1
Download PowerStar User Manual Uninterruptible Power Supply
Transcript
Important Safety Warnings This manual contains instructions and warnings that should be followed during the installation, operating and storage of the UPS system. Please keep this manual for further reference. CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive contaminants. (See the specifications for the acceptable temperature and humidity range.) CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and avoid exposing the unit to direct sunlight or installing the unit near heat emitting appliances such as space heaters or furnaces. CAUTION! Do not attach non-computer-related items, such as medical equipment, life-support equipment, microwave ovens, or vacuum cleaners to UPS. CAUTION! Do not plug the UPS input into its own output. CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid-containing vessels on or near the unit. CAUTION! In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS. CAUTION! Do not attach a power strip or surge suppressor to the UPS. CAUTION! If the UPS is with metal chassis, for safety purpose, grounding is a must during UPS installation in order to reduce leakage current below 3.5mA. Attention hazardous through electric shock. Also with disconnection of this unit from the mains, hazardous voltage still may be accessible through supply from battery. The battery supply should be therefore disconnected in the plus and minus pole at the quick connectors of the battery when maintenance or service work inside the UPS is necessary. CAUTION! Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required safety precautions. Keep unauthorized personnel away from batteries. CAUTION! When replacing the batteries, use the same number and type of batteries. CAUTION! Internal battery voltage is 12VDC. Sealed, lead-acid, 6-cell battery. CAUTION! Do not dispose of batteries in a fire. The battery may explode. Do not open or mutilate the battery or batteries. Released electrolyte is harmful to the skin and eyes. CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent. CAUTION! A battery can present a risk of electric shock and high short circuit current. The following precaution should be observed before replacing batteries: 1) Remove watches, rings, or other metal objects. 2) Use tools with insulated handles. 3) Wear rubber gloves and boots. 4) Do not lay tools or metal parts on top of batteries. 5) Disconnect charging source prior to connecting or disconnecting batteries terminal. PowerStar User Manual Uninterruptible Power Supply Specifications MODEL CAPACITY INPUT Input Voltage Voltage Range OUTPUT Voltage Regulation Transfer Time Waveform BATTERY Type & Number Charging Time PHYSICAL Dimension (DxWxH) mm Net Weight (kgs) MANAGEMENT USB Port PSTAR650 650 VA / 360 W PSTAR850 850 VA / 480 W PSTAR1000 1000 VA / 600 W 230 VAC 162-290 VAC +/-10% Typical 2-6 ms, 10 ms max. Simulated Sine Wave 12 V/7 AH x 1 12 V/9 AH x 1 12 V/7 AH x 2 4-6 hours recover to 90% capacity 287 x 100 x 142 4.25 4.9 350 x 146 x 160 8.0 Supports Windows® 2000/2003/XP/Vista/2008/7, Linux, Unix, and MAC Connection Chart Installation & Operation Initial Set-up Surge Protected Socket Surge Protected Socket After unpacking the unit, please avoid placing the unit in direct sun light, excessive heat, excessive humidity or in contact with fluids of any type. Place the unit away from other equipment at least 20 cm to avoid interference. Place the unit to avoid: - Direct sunlight Battery Backup Sockets - Excessive heat - Excessive humidity or contact with fluids Connect Utility Battery Backup Sockets 1000 650/850 Status Indicator AC mode LED: green lighting Battery mode LED: yellow lighting Fault LED: red lighting Plug the UPS into an electrical outlet that does not share a circuit with a heavy electrical load. Please allow the UPS to charge at least 6 hours prior to use. Connect Equipment UPS status LED AC Mode: green lighting Battery Mode: green flashing Connect critical equipment to “Battery Backup Sockets”. These battery backup sockets provide battery back-up and surge protection. In case of power outage, battery power is automatically provided to these outlets. Connect minor less critical devices to “Surge Protected Socket”. Power is not supplied to this socket when the utility fails. NOTE: Please DO NOT connect scanner or printer into “Battery Backup Sockets”. Connect Com. Port and Install Software Connect the communication port cable end to the communication port located on the rear Troubleshooting Problem No LED display on the front panel. panel of the UPS. Connect the other end of communication port cable to the port on the rear panel of the computer. Connect Modem/Phone/Network for Surge Protection Connect a single modem/phone line into surge-protected “IN” outlet on the back panel of the UPS unit. Connect from “OUT” outlet to the computer with another phone line cable. Power On/Off UPS Press power switch on the front panel of the UPS to turn on UPS. Press switch again to turn off the UPS. Solutions Charge the UPS at least 6 hours. Battery fault. Replace the battery with the same type of battery. Press the power switch again to turn on the UPS. Remove some loads first. Before reconnecting equipment, please verify that the load matches the UPS capability specified in the specs. Remove some critical load. The UPS is not turned on. Download the software from http://www.power-software-download.com/viewpower.html. Follow on-screen instruction to install the monitoring software. Possible Cause Low battery. Alarm continuously sounds when the mains is normal. The UPS is overload. When power fails, The UPS is overload. back-up time is shorten. Battery voltage is too low. Charge the UPS at least 6 hours. Battery defect. It might be due Replace the battery with the same to high temperature operation type of battery. environment, or improper operation to battery. The mains is normal but Power cord is loose. Reconnect the power cord properly. green LED is flashing.
