Download XR-CA360/CA360X

XR-CA360/CA360X
SERVICE MANUAL
E Model
XR-CA360/CA360X
Ver 1.2 2003.12
Saudi Arabia Model
XR-CA360
Photo: XR-CA360
Model Name Using Similar Mechanism
NEW
Tape Transport Mechanism Type
MG-36SZ13-32
SPECIFICATIONS
Cassette player section
Tape track
Wow and flutter
Frequency response
Signal-to-noise ratio
AM (E model)
Tuning range
4-track 2-channel stereo
0.13 % (WRMS)
30 – 15,000 Hz
55 dB
Aerial terminal
Intermediate frequency
Sensitivity
Tuner section
FM
Tuning range
(E model)
Tuning range
(Saudi Arabia model)
Aerial terminal
Intermediate frequency
Usable sensitivity
Selectivity
Signal-to-noise ratio
FM tuning interval:
50 kHz/200 kHz
switchable
87.5 – 108.0 MHz
(at 50 kHz step)
87.5 – 107.9 MHz
(at 200 kHz step)
87.5 – 108.0 MHz
External aerial connector
10.7 MHz/450 kHz
9 dBf
75 dB at 400 kHz
67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5 % (stereo),
0.3 % (mono)
Separation
35 dB at 1 kHz
30 – 15,000 Hz
Frequency response
AM tuning interval:
9 kHz/10 kHz switchable
531 – 1,602 kHz
(at 9 kHz step)
530 – 1,710 kHz
(at 10 kHz step)
External aerial connector
10.7 MHz/450 kHz
30 µV
General
Outputs
Inputs
Tone controls
MW/SW (Saudi Arabia model)
Tuning range
Aerial terminal
Intermediate frequency
Sensitivity
MW: 531 – 1,602 kHz
SW1: 2,940 – 7,735 kHz
SW2: 9,500 – 18,135 kHz
(except for 10,140 – 11,575
kHz)
External aerial connector
10.7 MHz/450 kHz
30 µV
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output 45 W × 4 (at 4 ohms)
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
Audio output
Power aerial relay control
lead
Power amplifier control
lead
BUS control input terminal
BUS audio input terminal
Low:
±10 dB at 60 Hz (Xplod)
Mid:
±10 dB at 1 kHz (Xplod)
High:
±10 dB at 10 kHz (Xplod)
12 V DC car battery
(negative earth)
Approx. 178 × 50 × 178 mm
(w/h/d)
Approx. 182 × 53 × 161 mm
(w/h/d)
Approx. 1.2 kg
Parts for installation and
connections (1 set)
Front panel case (1)
Design and specifications are subject to change
without notice.
E model
FM/AM/CASSETTE CAR STEREO
Saudi Arabia model
FM/MW/SW CASSETTE CAR STEREO
9-874-258-03
Sony Corporation
2003L05-1
C 2003.12
e Vehicle Company
Published by Sony Engineering Corporation
CA
XR-CA360/CA360X
Ver 1.2
TABLE OF CONTENTS
SERVICING NOTES
SERVICING NOTES ......................................................... 2
SERVICE POSITION
In checking the control board and main board, prepare two jigs
(extension (MD) cord J-2502-060-1 and
connection cable for F/P to main J-2502-072-1).
1.
GENERAL
Location of Controls ....................................................... 3
Setting the Clock ............................................................. 3
main board (CN300)
main board (CN350)
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
2-8.
2-9.
Disassembly Flow ...........................................................
Sub Panel .........................................................................
Mechanism Deck (MG-36SZ13-32) ...............................
MAIN Board ...................................................................
Heat Sink .........................................................................
Bracket (MD) ..................................................................
DC Motor (Capstan/Reel) (M901) .................................
Main Belt, Sub Belt (C) ..................................................
Magnetic Head (Playback) (HP901) ..............................
3.
MECHANICAL ADJUSTMENTS ....................... 12
4.
ELECTRICAL ADJUSTMENTS
7
7
8
8
9
9
10
10
11
main board
(CN600)
mechanism deck
Tape Deck Section .......................................................... 12
Tuner Section .................................................................. 13
5.
connect jig
(extention (MD) cord J-2502-060-1)
to the main board (CN300, CN350)
and mechanism deck.
DIAGRAMS
5-1. Note for Printed Wiring Boards and
Schematic Diagrams .......................................................
5-2. Printed Wiring Board – MAIN Board – ........................
5-3. Schematic Diagram – MAIN Board (1/2) – ..................
5-4. Schematic Diagram – MAIN Board (2/2) – ..................
5-5. Printed Wiring Board – CONTROL Board – ................
5-6. Schematic Diagram – CONTROL Board – ...................
5-7. IC Pin Function Description ...........................................
14
15
16
17
18
19
21
6.
EXPLODED VIEWS
6-1.
6-2.
6-3.
6-4.
General Section ...............................................................
Front Panel Section .........................................................
MAIN Board Section ......................................................
Mechanism Deck Section (MG-36SZ13-32) .................
7.
ELECTRICAL PARTS LIST ............................... 27
23
24
25
26
control board (CN900)
connect jig
(connection cable
for F/P to main J-2502-072-1)
to the main board (CN600) and
control board (CN900).
Note of replacing of the IC1
In this set, the IC1 on the MAIN board is changed from the midway of the production.
When the replacing of the IC1, be sure to check the model name
printed by IC, and replace the IC1 by following the instructions
below.
• When replacing of the IC1 (MN101C49HAS)
Replace the IC1 with the MN101C49HEA (Part No.: 6-603178-01), and replace the TU101 (A-3220-944-A) simultaneously.
• When replacing of the IC1 (MN101C49HEA)
Perform the usual replacing.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
2
XR-CA360/CA360X
SECTION 1
GENERAL
This section is extracted from
instruction manual.
Setting the clock
Location of controls
The clock uses a 12-hour digital indication.
Example: To set the clock to 10:08
1
The hour indication flashes.
DIR
SOURCE
EQ3
SEEK
MODE
1 Press either side of the volume button
to set the hour.
DSPL
DISC
RELEASE
SEL
ATT
1
2
REP
SHUF
3
4
ATA
5
6
Press (DSPL) for 2 seconds.
BTM
SENS
OFF
to go forward
XR-CA360X/CA360
to go back
Refer to the pages listed for details.
1 SOURCE (Radio/CD/MD) button
2 MODE button
During radio reception:
Band select
During CD/MD playback:
CD/MD unit select
3 Volume +/– button
4 Z (eject) button
5 Display window
6 m/M (fast winding)/DIR (tape
transport direction change) buttons
7 SEEK button
Seek
Automatic Music Sensor
Manual search
8 DSPL (display mode change) button
9 EQ3 button
0 RELEASE (front panel release) button
qa SEL (select) button
qs RESET button (located on the front side
of the unit behind the front panel)
qd ATT (attenuate) button
qf Number buttons
During radio reception:
Preset number select
2 Press (SEL).
During CD/MD playback:
(1) DISC –
(2) DISC +
(3) REP
(4) SHUF
The minute indication flashes.
3 Press either side of the volume button
to set the minute.
qg Frequency select switch (E model)
(located on the bottom of the unit)
See “Frequency select switch” in the
Installation/Connections manual.
to go forward
qh BTM/ATA button
to go back
qj SENS button
qk OFF button*
* Warning when installing in a car
without ACC (accessory) position on
the ignition key switch
Be sure to press (OFF) on the unit for 2
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) momentarily, the
clock display does not turn off and this
causes battery wear.
2
Press (DSPL).
The clock starts.
After the clock setting is complete, the
display returns to normal play mode.
3
XR-CA360/CA360X
2
A
B
BUS AUDIO IN
BUS CONTROL IN
AUDIO OUT
REAR
BUS AUDIO IN
Source selector*
Selector de fuente*
XA-CA30
* not supplied
no suministrado
BUS CONTROL IN
Cautions
Connection example (2)
•This unit is designed for negative earth 12 V DC
operation only.
•Do not get the wires under a screw, or caught in
moving parts (e.g. seat railing).
•Before making connections, turn the car ignition
off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth wires to a common earth point.
•Be sure to insulate any loose unconnected wires
with electrical tape for safety.
Notes (2-B- )
• Be sure to connect the earth cord before connecting
the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will be
deactivated.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
•The numbers in the list are keyed to those in the
instructions.
•The bracket 1 and the protection collar 5 are
attached to the unit before shipping. Before
mounting the unit, use the release keys 7 to
remove the bracket 1 and the protection collar
5 from the unit. For details, see “Removing the
protection collar and the bracket (4)” on the
reverse side of the sheet.
•Keep the release keys 7 for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
1
Catch
Note
Before installing, make sure that the catches on both
sides of the bracket 1 are bent inwards 2 mm. If the
catches are straight or bent outwards, the unit will not
be installed securely and may spring out.
4
Tip (2-B- )
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
Connection diagram (3)
1 To a metal surface of the car
First connect the black earth lead, then connect the
yellow and red power input leads.
2 To the power aerial control lead or power supply
lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there is no
power aerial or aerial booster, or with a manuallyoperated telescopic aerial.
• When your car has a built-in FM/AM aerial in the
rear/side glass, see “Notes on the control and
power supply leads.”
3 To AMP REMOTE IN of an optional power amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the +12 V power terminal which is energised in
the accessory position of the ignition key switch
Notes
• If there is no accessory position, connect to the +12
V power (battery) terminal which is energised at
all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
• When your car has a built-in FM/AM aerial in the
rear/side glass, see “Notes on the control and
power supply leads.”
5 To the +12 V power terminal which is energised at
all times
Be sure to connect the black ground lead to a metal
surface of the car first.
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM aerial in the rear/
side glass, connect the power aerial control lead
(blue) or the accessory power input lead (red) to the
power terminal of the existing aerial booster. For
details, consult your dealer.
• A power aerial without relay box cannot be used with
this unit.
Memory hold connection
When the yellow power input lead is connected, power
will always be supplied to the memory circuit even
when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and
with adequate power handling capacities to avoid its
damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right speakers
with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares a
common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each other.
XR-CA360/CA360X
3
Equipment used in illustrations
(not supplied)
Equipo utilizado en las ilustraciones
(no suministrado)
Supplied with XA-C30
Suministrado con el XA-C30
Supplied with the CD/MD changer
Suministrado con el cambiador de CD/MD
Source selector
(not supplied )
Selector de fuente
(no suministrado )
Fuse (10 A)
Fusible (10 A)
XA-C30
Front speaker
Altavoces delanteros
BUS
CONTROL IN
Rear speaker
Altavoces traseros
BUS AUDIO IN
from car aerial
de antena de automóvil
BUS
AUDIO IN
Power amplifier
Amplificador de potencia
AUDIO
OUT
AUDIO
OUT REAR
CD/MD
Cambiador de CD/MD
RCA pin cord (not supplied)
Cable con clavijas RCA (no suministrado)
Blue/white striped
Con raya azul/blanca
6
AMP REM
3
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
White
Blanco
Left
Izquierdo
Black
Negro
1
White/black striped
Con raya blanca/negra
Grey
Gris
Blue
Azul
ANT REM
Right
Derecho
Grey/blackstriped
Con raya gris/negra
Green
Verde
Left
Izquierdo
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
Red
Rojo
4
Green/black striped
Con raya verde/negra
Purple
Púrpura
Right
Derecho
2
Yellow
Amarillo
5
Purple/blackstriped
Con raya violeta/negra
Precautions
Mounting example (5)
•Choose the installation location carefully so that the unit will not
interfere with normal driving operations.
•Avoid installing the unit in areas subject to dust, dirt, excessive
vibration, or high temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for a safe and secure
installation.
Installation in the dashboard
Notes
• Bend these claws outward for a tight fit, if necessary (5-2).
• Make sure that the 4 catches on the protection collar 5 are properly
engaged in the slots of the unit (5-3).
Mounting angle adjustment
Mounting the unit in a Japanese car (6)
Adjust the mounting angle to less than 20°.
Removing the protection collar and the
bracket (4)
Before installing the unit, remove the protection collar 5 and
the bracket 1 from the unit.
1
2
Remove the protection collar 5.
1 Engage the release keys 7 together with the protection collar
5.
2 Pull out the release keys 7 to remove the protection collar 5.
Remove the bracket 1.
1 Insert both release keys 7 together between the unit and the
bracket until they click.
2 Pull down the bracket 1, then pull up the unit to separate.
Warning when installing in a car without ACC
(accessory) position on the ignition key
switch
Be sure to press (OFF) on the unit for two seconds to turn
off the clock display after turning off the engine.
When you press (OFF) only momentarily, the clock display does not
turn off and this causes battery wear.
You may not be able to install this unit in some makes of Japanese
cars. In such a case, consult your Sony dealer.
RESET button
Note
To prevent malfunction, install only with the supplied screws 4.
When the installation and connections are completed, be sure to
press the RESET button with a ballpoint pen, etc., after detaching the
front panel.
How to detach and attach the front panel
(7)
Before installing the unit, detach the front panel.
7-A To detach
Before detaching the front panel, be sure to press (OFF).
Press (RELEASE), then slide the front panel to the left, and pull it off
towards you.
7-B
To attach
Attach part A of the front panel to part B of the unit as illustrated
and push the left side into position until it clicks.
Frequency select switch (E model)
The AM (FM) tuning interval is factory-set to the 9 k (50 k) position.
If the frequency allocation system of your country is based on 10 kHz
(200 kHz) interval, set the switch on the bottom of the unit to the 10 k
(200 k) position before making connections.
5
XR-CA360/CA360X
2
41
7
7
5
c
c
c
Orient the release key
correctly.
Oriente la llave de
liberación en la dirección
correcta.
Face the hook inwards.
El gancho debe
encontrarse en la parte
interior.
1
51
3
2
Dashboard
Salpicadero
Fire wall
Panel cortafuegos
1
182
mm
5
2
53 m
m
Claws
Uñas
3
1
6A
B
TOYOTA
NISSAN
4
4
max. size
5 × 8 mm
Tamaño máx.
5 × 8 mm
max. size
5 × 8 mm
Tamaño máx.
5 × 8 mm
to dashboard/centre console
al salpicadero/consola central
4
Bracket
Soporte
max. size
5 × 8 mm
Tamaño máx.
5 × 8 mm
Bracket
Soporte
(OFF)
4
Bracket
Soporte
max. size
5 × 8 mm
Tamaño máx.
5 × 8 mm
Bracket
Soporte
Existing parts supplied with your car
Piezas existentes suministradas con su automóvil
Existing parts supplied with your car
Piezas existentes suministradas con su automóvil
7A
to dashboard/centre console
al salpicadero/consola central
B
A
B
(RELEASE)
6
XR-CA360/CA360X
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1.
DISASSEMBLY FLOW
Note 1: The process described in
can be performed in any order.
Note 2: Without completing the process described in
, the next process can not be performed.
Note 3: Illustration of disassembly is omitted.
SET
FRONT PANEL SECTION
(Note 3)
COVER
(Note 3)
2-2. SUB PANEL
(Page 7)
2-3. MECHANISM DECK (MG-36SZ13-32)
(Page 8)
2-4. MAIN BOARD
(Page 8)
2-6. BRACKET (MD)
(Page 9)
2-5. HEAT SINK
(Page 9)
2-7. DC MOTOR
(CAPSTAN/REEL) (M901)
(Page 10)
2-8. MAIN BELT,
SUB BELT (C)
(Page 10)
2-9. MAGNETIC HEAD
(PLAYBACK) (HP901)
(Page 11)
Note: Follow the disassembly procedure in the numerical order given.
2-2.
SUB PANEL
1 two claws
1 claw
1 two claws
2 sub panel
7
XR-CA360/CA360X
2-3.
MECHANISM DECK (MG-36SZ13-32)
2 two screws
(PTT2.6 × 6)
2 two screws
(PTT2.6 × 6)
1 connector
(CN350)
3 mechanism deck
(MG-36SZ13-32)
1 connector
(CN300)
2-4.
MAIN BOARD
4 main board
2 two ground point screws
(PTT2.6 × 6)
3 two screws
(PTT2.6 × 6)
3 screw
(PTT2.6 × 6)
1 claw
8
XR-CA360/CA360X
2-5.
HEAT SINK
1 two screws
(PTT2.6 × 10)
2 heat sink
1 five screws
(PTT2.6 × 10)
2-6.
BRACKET (MD)
1 claw
1 claw
3 bracket (MD)
1 claw
2 four screws
(B2.6 × 4)
9
XR-CA360/CA360X
2-7.
DC MOTOR (CAPSTAN/REEL) (M901)
2 main belt
3 sub belt (C)
1 two screws
(P2 × 2.5)
4 DC motor (capstan/reel)
(M901)
Note : When installing motor,
adjust the screw and
screw hole of motor.
2-8.
MAIN BELT, SUB BELT (C)
1 main belt
2 screw
(PTP2 × 3)
4 sub belt (c)
A
2 screw
(PTP2 × 3)
2 screw
(PTP2 × 3)
2 screw
(PTP2 × 3)
10
3 Lift up the bottom BKT (TS)
in the direction of arrow A
(as far as the belt can be removed).
XR-CA360/CA360X
2-9.
MAGNETIC HEAD (PLAYBACK) (HP901)
2 screw
(PTT2 × 4)
3 FF/REV lever section
1 screw
(P2 × 3)
7 PSW (reel) B
9 screw
(P2 × 4)
8 HP roller (A)
0 SPG support plate
qa adjuster arm SPG (A)
qs adjuster arm SPG (B)
6 slide SW board
qf magnetic head (play back)
(HP901)
4 Remove the three solders
of magnetic head lead wires.
5 screw
(PTP2 × 3)
qd Remove three magnetic
head lead wires from
the adjuster arm blue.
adjuster arm blue
magnetic head lead wire
• MAGNETIC HEAD LEAD WIRE COLOR INDICATION
ON HEAD (HP901) AND SLIDE SW BOARD.
magnetic head
(HP901)
yellow lead wire
black lead wire
red lead wire
slide SW board
11
XR-CA360/CA360X
SECTION 3
MECHANICAL ADJUSTMENTS
1. Clean the following parts with a denatured-alcohol-moistened
swab:
playback head
pinch roller
rubber belt
capstan
idler
2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the power supply
voltage (14.4 V) unless otherwise noted.
Note: With this set, it is not necessary to apply suitable locking
compound to the parts after the azimuth adjustment.
SECTION 4
ELECTRICAL ADJUSTMENTS
TAPE DECK SECTION
0 dB= 0.775 V
1. The adjustments should be performed in the order given in
this service manual.
2. The adjustments should be performed for both L-CH and
R-CH.
TEST TAPE
Type
Signal
Used for
P-4-A063
6.3 kHz, –10 dB
head azimuth adjustment
WS-48A
3 kHz, 0 dB
tape speed adjustment
• TORQUE MEASUREMENT
Mode
Torque Meter
Meter Reading
CQ-102C
2.46 – 5.39 mN•m
(25 – 55 g•cm)
(0.35 – 0.76 oz•inch)
CQ-102C
0.15 – 0.39 mN•m
(1.5 – 4 g•cm)
(0.02 – 0.06 oz•inch)
CQ-102RC
2.46 – 5.39 mN•m
(25 – 55 g•cm)
(0.35 – 0.76 oz•inch)
Reverse
Back Tension
CQ-102RC
0.15– 0.39 mN•m
(1.5 – 4 g•cm)
(0.02 – 0.06 oz•inch)
FF, REW
CQ-201B
4.91 – 14.70 mN•m
(50 – 150 g•cm)
(0.69 – 2.08 oz•inch)
Forward
Forward
Back Tension
Reverse
Tension Meter
Forward
CQ-403A
Reverse
CQ-403R
test tape
P-4-A063
(6.3 kHz, –10 dB)
level
meter
4Ω
+
–
set
speaker out terminal
2. Turn the screw and check the output peak value. Adjust the
screw so that the peak value in channels L and R coincides
within 3 dB.
within
3 dB
L-CH
peak
• TAPE TENSION MEASUREMENT
Mode
PB HEAD AZIMUTH ADJUSTMENT
Procedure:
1. Put the set into the FWD PB mode.
within
3 dB
output
level
Meter Reading
more than 5.89 mN•m
(more than 60 g)
(more than 2.12 oz)
screw
position
R-CH
peak
angle
L-CH
peak
R-CH
peak
3. Check the phase in the FWD PB mode.
test tape
P-4-A063
(6.3 kHz, –10 dB)
oscilloscope
4Ω
L-CH
V
set
R-CH
H
+ +
– –
4Ω
speaker out terminal
Screen pattern
in phase 45 °
good
90 ° 135 ° 180 °
wrong
4. Repeat the above adjustment for the REV PB mode.
5. Check that output level difference between FWD PB mode
and REV PB mode is within 4 dB.
Adjustment Location: PB head (See page 13)
12
XR-CA360/CA360X
TAPE SPEED ADJUSTMENT
Setting:
test tape
WS-48A
(3 kHz, 0 dB)
frequency counter
4Ω
+
–
set
speaker out terminal
Procedure:
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the
reading on the frequency counter becomes in 3,015 Hz.
Specified Value: 2,940 to 3,090 Hz
Adjustment Location: DC motor
TUNER SECTION
Tuner section adjustments are done automatically in this set.
Adjustment Location: PB head
Adjustment Location: DC motor
– Set Upper View –
– Set Upper View –
Tape Speed Adjustment
FWD 

 adjustment
 screws
REV 
13
XR-CA360/CA360X
Ver 1.2
5-1.
SECTION 5
DIAGRAMS
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
z
•
: Through hole.
•
: Pattern from the side which enables seeing.
: Carbon pattern.
•
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Abbreviation
EA
: Saudi Arabia model
• When replacing the IC1, refer to servicing note (Page 2 “When
replacing the IC1”).
14
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• C : panel designation.
• A : B+ Line.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from ACC and BATT cords.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
〈〈
〉〉 : TAPE PLAYBACK
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
f : AM
E : TAPE PLAYBACK
L : BUS AUDIO IN
• Abbreviation
EA
: Saudi Arabia model
• When replacing the IC1, refer to servicing note (Page 2
“When replacing the IC1”).
XR-CA360/CA360X
Ver 1.2
5-2.
PRINTED WIRING BOARD – MAIN Board –
1
2
Note: When replacing the IC1, refer to servicing note (Page 2 “When replacing the IC1”).
3
4
A
5
6
7
8
9
10
11
6
CN400
BUS
AUDIO IN
ANT100
(FM/AM ANTENNA)
L
R
R
CN800
(BUS CONTROL IN)
(FOR SONY BUS)
7
3
L
13
4
5
8
AUDIO
OUT
12
2
1
F901
TO
CN700
(FRONT VIEW)
9
1
JW2
JW60
JW181
JC30
BCE
R50
JW172
GND
BATT
D805
Q800
R811
4 3
1 2
R81
IC2
JW84
8
JW112
ORG
BCE
BRN
JW88
RED
(CHASSIS)
Q651
R711
R712
JW176
R656
R607
D651
S1
RESET
JW86
1
JW87
ECB
BLU
Q710
1
S901
(DIRECTION)
REV
m
FWD
BRN
C710
Q711
S902
(FF/REW)
(OFF : PLAYBACK)
ORG
TO
CN350
JC170
Q350
JC166
8
Q351
S903
(TAPE DETECT)
(ON : TAPE IN)
YEL
YEL
E
R353
JW102
C
CN350
JW85
JW82
R350
JW80
C4
C733
C732
Q730
B
BCE
C3
Q731
R732
D350
50kHz 9kHz
15
C730
JW149
R657
(Page 18)
D731
R730
R352
JW128
C2
C1
R2
L1
SW1
FREQUENCY
SELECT
AM
FM
200kHz 10kHz
CONTROL BOARD
CN900
ECB
R59
R60
X2
Q732
C731
R3
C734
R722
JW98
R4
R5
JC147
R731
R655
11
15
C7
JW145
-2
R36
R710
YEL
ACC
R800
ECB
R740
JW138
JW29
BCE
R654
JW139
8
R713
R58
JW159
JW161
JW162
JW163
-1
12
A
7
R815
JW144
JW114
(E)
C600
R600
R601
R602
R603
R604
R605
R606
JW146
CN600
1
14 C801
R814
JW143
R7
R6
JW151
R303
R302
JW150
JW157
C314
JW171
C601
R852
JW137
R26
R16
R17
R1
C6
R42
JW158
2
JW22
TH800
R720
BCE
R44
R53
R27
R19
1
8
BLK
IC800
1
R804
R351
100
ANT REM
Ref. No.
Location
D250
D253
D300
D350
D451
D452
D500
D501
D502
D503
D504
D505
D506
D507
D650
D651
D653
D700
D721
D722
D723
D724
D731
D741
D742
D800
D802
D803
D805
D-5
D-5
G-3
H-10
D-6
D-6
C-7
C-7
C-7
C-7
D-7
D-7
C-7
D-7
E-9
J-10
D-9
D-10
D-8
D-9
D-8
D-9
H-11
E-10
D-10
E-10
E-11
E-11
F-11
IC1
IC2
IC300
IC400
IC500
IC800
G-7
G-11
H-3
E-3
B-6
E-11
Q251
Q252
Q253
Q350
Q351
Q400
Q401
Q402
Q403
Q450
Q451
Q650
Q651
Q710
Q711
Q722
Q724
Q725
Q726
Q730
Q731
Q732
Q740
Q741
Q800
E-5
E-5
E-6
I-11
H-10
D-4
D-4
D-3
D-4
D-5
D-6
E-9
I-9
I-11
I-10
D-8
D-7
E-8
E-7
H-11
G-11
G-10
D-10
E-10
F-11
JW140
JW103
X1
R39
JW61
JW62
JW13
JW5
R721
ECB
JW135
R18
R46
R48
25
R40
16
L700
7
RED
C81
R31 (E)
+
JW76
JW113
BCE
JW116
R33
R205
C742
D741
JW117
R38
JW66
C315
(CHASSIS)
J
C8
26
JW68
+
I
JW59
JW3
JW4
R728
JW96
JW95
JW94
R503
R502
IC1
C5
C305
C740
R12
76
R307
R306
R13
R43
JW152
R305
1
C304
C303
R35
R309
14
R25
(EA)
JC148
R304
JW172
R311
C650
JW77
R28 (CA360X) 75
JW153
IC300
R308
R301
R37
15
+
C306
C302
R8
R9
+
JW99
R314
C307
7
R310
R300
R11
R30 (EA)
8
1
R10
R54
AMP REM
D803
JW142
50
FRONT RCH (–)
Q741
BCE
+
R14
R653
C741
R22
51
FRONT RCH (+)
D802
D800
R651 D650
Q650
R29 (CA360)
JW125
C311
CN300
3
BCE
C262
R262
R264
R259
BCE
JW115
JW124
JW127
R49
R55
REAR RCH (–)
JW26
JW141
R21
+
D300
+
JC169
JC133
C310
R56
R41
C312
H
JC53
JW89
JW55
JW108
R312
JC132
JW126
G
R57
R47
JW48
JW58
JW57
R401
JW123
JW120
R423
JW121
C414
C415
JW105
R263
C505
JW118
R422
JW42
HP901
PLAYBACK
HEAD
R452
B CE
JW47
Q253
REAR RCH (+)
JW27
Q740
D653
D724
R652
Q725
REAR LCH (–)
D700
+
R313
JC52
17
R250
JW46
C413
JW56
C400
C401
C412
R418
JW90
JW177
R102
R106
R419
JW129
JW54
C100
12
C
E
Q726
REAR LCH (+)
+
11
R105
F
C411
R420
Q252
R500
+
C104
R421
C451
Q251
B
JW45
R505
D721
6
BLU
FRONT LCH (–)
JW28
D742
+
JC104
JC44
R650
D722
R663
+
C251
14
5
BLU/WHT
JW17
Q722
JW97
C452
R400
R801
+
TH700
D723
Q724
R451
JW100
C105
JC49
4
GRY
GRY/BLK
13
JW18
JW92
R20
ECB
22
D452
Q451
D451
JC91
JC83
1
R101
E
R450
+
+
+
12
C800
JW19
JW24
TH701
D250
4
R802
JW23
JW180
D253
7
C701
D507
R501
VIO
FRONT LCH (+)
JW20
D504
Q403
Q450
C410
5
3
VIO/BLK
C700
D505
+
IC400
C409
C404
R664
D501 D502
+
C419
+
8
D506
R405
JW51
+
D500
C500
R413
1
JC110
B CE
Q401
R403
C417
+
JW7
C503
Q400 JW35
R402
C416
JW32
JW31
ECB
JW34
R409
6
16
CN700
R411
C250
C405
R407
B CE
C418
+
C106
R406
R408
R404
1
C423
JW50
D
C427
C421
C420
Q402
TU100
TUNER UNIT
C425
C424
JW33
R410
C422
9
11
CN800
3 2 1
19
8
D503
JW6
C522
C521
R412
C426
18
C523
C520
C
17
1
R725
C429
IC500
25
JW122
C428
C431
C430
JW119
R415
GRN
GRN/BLK
2
R24
R414
24
JC134
R417
JW9
R416
JW8
JW15
C403
2
JW10
+
C402
10
C507
R23
JC173
C508
JW36
B
JW11
JW16
JW12
R853
WHT
WHT/BLK
MAIN BOARD
• Semiconductor
Location
1-686-927-
11
M
M901
(CAPSTAN/REEL)
XR-CA360/CA360X
Ver 1.2
5-3. SCHEMATIC DIAGRAM – MAIN Board (1/2) –
Note: When replacing the IC1, refer to servicing note (Page 2 “When replacing the IC1”).
E2P SDA
E2P SCL
E2P VDD
TU SDA
TU SCL
GND2
TU VDD
VCC
RDS
S METER
TU MUTE
MUTE CON
TU100
TUX-031//Q2
TUNER UNIT
QUALITY
L
R
GND1
ANT
(1/2)
• See page 20 for Waveforms.
A1
A2
A3
A4
ANT100
(FM/AM ANTENNA)
R101
22k
C105
0.1
C104
0.1
C106
100
10V
R102
3.3
TU4
TU5
R106
220
TU8
TU10
(CHASSIS)
TU9
TU1
R105
220
TU7
C100
0.047
R263
10
Q251
2SD1664
R259
10k
R262
1k
B2
B1
Q252
2PB710A
R250
470
+5V REGULATOR
Q252,253
R264
1k
D253
1SS133
TUNER
B+ SWITCH
C251
10
16V
C250
0.01
D250
MTZJ5.1A
Q253
PDTC114EK
L1
C262
1
A5
A6
BUS6
TU10
AU2
AU1
R53 100
R16 100k
R26 100
AU4
AU3
R27 100
R44 100
R18 100 BUS4
R17 47k
R19 100 BUS5
R57 0
R24
10k
R23 10k
R56
0
R20 100 BUS3
TU7
TU8
TU11
R43 R50
0 100
R13
100
R306
56
R312
1k
CN300
3P
L
R302
100
L-CH
R-CH
1/2VCC
C302
0.001
R300
47k
C303
0.001
R301
47k
C304
100p
R304
100
D300
1SS133
R314
10
DAVN
BU-IN
NC
NIL
NCI
TU-ATTIN
NC
RESET
BEEP
ILL-IN
POWER-ON
ACC-IN
NC
TEL-ATT
NCI
BUS-SO
BUS-SI
NC
NC
NC
LO/
RIP
NC1
N/R
FWD
GND
FF/REW
XI
C3 18p
VSS
LCD-RES
LCD-CE
PNL2
SYSTEM CONTROLLER
OSC1
IC1
MN101C49HEA
OSC2
VDD
FLASH-W
(FF/REW)
TAPE1
R14
100k
TAPE2
GND
TAPE-IN
S903
(TAPE DETECT)
R303
100
TAPE3
C305
100p
R305
100
R309
330k
R313
1k
MPTH
NC
QUALITY
NC
NC
NC
NC
NC
NC
D1
LAMP+B
R42
0
C6
22
10V
A11
R58
1k
TU1
DAVDD
TAPE-IN
FF/REW
N/ R
NS-MASK
DAVSS
TAPE-ON
NC
NOSE-SW
VREFC5
0.1
(E)
LAMP+B
SW1
FREQUENCY
R606 1k
PNL7
CAPSTAN/REEL
LCD-CE
MOTOR DRIVE
R351
1.5k
R352
1.5k
LCD-DO
(EA)
R35 100k
PNL6
R33 100k
R605 1k
(E)
R31 100k
Q350,351
R28 0
LCD-DI
(EA)
(CA360X)
PNL5
R604 1k
A12
SELECT
R350
10k
R30 0
C600
0.1
(CA360)
LCD-CLK
R29 100k
LCD-RESET
FM
AM
200k
10k
50k
9k
A13
A14
A15
-1
-2
R39
100k
(E)
R36
100k
D350
11ES2
(CHASSIS)
S1
RESET
PNL1
R607
1k
(CHASSIS)
16
16
TAPE3
GND
TAPE4
TAPE2
Q351
PDTC114EK
GND
TAPE1
DRIVE+5V
TAPE4
(Page 19)
NC
PNL4
R41
0
VSM
NC
R603 1k
C1
12p
Q350
2SA1428
R353
1
FRASH WRITE
NC
PNL3
COL-SEL
ILL-ON
R602 1k
R9
100
NC
PNL2
NC
PNL1
R601 1k
NC
R600 1k
NOSE-SW
NC
CN600
12P
NC
EE-CKO
NC
EE-SIO
(CHASSIS)
R1 R2
1k 0
NC
NC
TU5
NC
TU4
R8
100
NC
C310
1
50V
R311
15k
DEST-SEL2
C307
0.01
DEST-SEL1
R307
56
DEST-SEL0
C314
100 6.3V
A10
R3
100k
X1
18.432MHz
NC
NC
GND
(ON:TAPE IN)
C2
12p
PNL5
VREF+
NC
R54
100
(OFF:PLAYBACK)
R60
100
XO
AM-ON
R11
100
PNL7
R4
4.7k
MMOD
TEST-IN
S902
R5
100
LCD-SO(TX)
X2 32.768KHz
R10
100
PNL6
MOTOR-
A9
R59
1k
R55 100
TAPE EQUALIZER
IC300
HA12232FP-EL
PNL4
R6
100
LCD-SI(RX)
NC
VCC
NC3
NC2
CN350
8P
NC4
R7
1k
LCD-CKO
DX
FM-ON
MOTOR+
REV
NC
TU-ATT
VOL-ATT
VREF GND
(CAPSTAN/REEL)
SYS-RES
NC
TU-ON
PNL3
S901
BUS1
R37 100k
M901
(DIRECTION)
BUS-ON
NC
R25
100
AU8
R
A8
BUS2
D2
R308
330k
C315
100
6.3V
R49
100
KEYACK
C4 22p
C312
100
10V
C311
470p
NC
TU9
R310
15k
TUI11
C306
0.01
HP901
(PLAYBACK)
R12
100k
BUS-CKO
NC
NC
R21
100
I2C-SIO
R48 100
I2C-CKO
R47 100
AU7
AMP-ON
AU6
ATT
R46 100
AMP-ATT
AU5
R205
0
C8
0.001
R22
100
R40
100k
R38
100k
A16
(Page 17)
XR-CA360/CA360X
SCHEMATIC DIAGRAM – MAIN Board (2/2) –
• See page 20 for IC Block Diagrams.
(2/2)
CN400
BUS AUDIO IN
R
AUDIO OUT
L
R
L
R853
0
(CHASSIS)
A1
A2
A3
(CHASSIS)
A4
IC500
TA8272H
POWER AMP
GND
R416
10k
R414
1k
C428
100p
R417
10k
R415
1k
C429
100p
C431
3300p
C430
3300p
D502
11ES2
SP2
D501
11ES2
FL+
C424
0.47
C417
4.7
50V
OR2
R410
10k
C522
47p
C500
10
16V
SP3
GND
R406
47k
R407
47k
D500
11ES2
SP4
RIPPLE
RL+
R402
100
FL IN
Q400
DTC314TK
RL IN
CN700
16P
C520
47p
FR IN
MUTING
AU1
C521
47p
Q401
DTC314TK
R500
47k
R505
0
C503
0.001
RR IN
SP5
RR+
MUTING
C421
0.47
R403
100
C425
0.47
R501
2.2k
R411
10k
GND
D507
11ES2
C508
0.1
SP6
VCC1
OF1
R423 0
C412
10p
R408
47k
C413
10p
R409
47k
C419
4.7
50V
OR1
R412
10k
SP1
FL-
FRONT LCH+
SP4
RL+
FRONT LCH-
SP3
RL-
REAR LCH+
SP5
RR+
REAR LCH-
SP6
RR-
REAR RCH+
SP7
FR+
REAR RCH-
FR-
FRONT RCH+
AMP-REM
MUTE
C505
10
16V
FRONT RCH-
AU6
SP8
SP7
FR+
C523
47p
MUTING
D505
11ES2
SP8
ATT-REM
GND
D504
11ES2
FR-
R502
10k
AMP REM
ACC
TEST
R664
1k
Q403
DTC314TK
C423
0.47
R413
10k
C700
3300
16V
C701
0.22
D700
IN5404TU
BATT
BATT
GND
F901
10A
32V
AU7
AU2
TU7
C427
0.47
ANT REM
GND
ACC
L700
250µH
MUTING
R405
100
AU3
AU8
TU8
R401
39k
AU4
C426
0.47
Q402
DTC314TK
C411
0.01
R400
10
C422
0.47
R404
100
OF1
R422 0
R421 100
R420 100
R419 100
OR1
OR2
C410
47
16V
OF2
R418
100
D506
11ES2
RRC418
4.7
50V
FL+
BEEP
A5
A6
SP2
GND
AGND
C415
10p
DGND
12C_DATA
FIL
AN
AP1
MUTE
12C_CLK
AP2
SEL
B2
B1
ADJ
C1
OUT_F1
VCC
C2
OUT_R1
D2
D1
OUT_F2
OUT_R2
IC400
BD3803F-FE2
SP1
VCC2
C420
0.47
C414
10p
VOLUME
D503
11ES2
FLSTBY
RL-
C416
4.7
50V
ELECTRICAL
R503
1k
C507
0.1
OF2
INPUT SELECT,
AU5
D653
MTZJ6.2B
B1
C405 0.47
C403 0.47
B2
C404 0.47
C409 10 16V
D1
C401 0.47
C402 0.47
D2
C400 0.47
GND
A8
TU11
(Page 16)
R657
100
Q730
2SD1760
R654
100k
Q722
2SA1428
+9V REGULATOR
R852
0
A9
Q651
2PB709A
ACCESSORY
R656
27k
R655
47k
C601
0.1
R653
4.7k
CHECK
C650
1
50V
R651
47k
D451
1SS133
R450
47
TH700
Q731
2PB709A
R650
4.7k
D650
MTZJ18B
Q650
2PD601A
B+ SWITCH
D651
1SS133
Q450
PDTA114EK
R652
47k
Q724
2SA1428
R732
470
TH701
R720
10k
R730
10k
D721
11ES2
D723
11ES2
Q450,451
A10
MUTING
R81
100k
Q731,732
IC2
PST3443UL
R451
10k
C733
470p
NC
GENERATOR
REGULATOR
C452
1
VDD
SWITCH
RESET SIGNAL
C7
0.047F
5.5V
R452
4.7k
CONTROL
VSS VOUT
5-4.
C81
0.1
Q451
PDTC144EK
R663
100k
D452
MTZJ7.5C
C732
1
C451
47
16V
C730
10
16V
CONTROL
R721
560
1/2W
Q722,724-726
R731
2.2k
B+ SWITCH
R728
10k
R725
560
1/2W
SWITCH
D731
MTZJ9.1C
C734
1
R722
0
Q732
PDTC114EK
Q726
PDTC114EK
D724
11ES2
D722
11ES2
Q725
PDTC114EK
C731
0.047
A11
CN800
8P
BUS CONTROL IN
(FOR SONY BUS)
R710
4.7
1/2W
Q710
2SA1428
GND
R713
10k
BUS5
R814
220k
B+ SWITCH
R712
1.5k
BUS6
R711
1.5k
R815
0
Q740
2SA1428
A12
DATA
OUT
DATA
IN
BUS4
Q710,711
D742
1SS133
BUS-CLK
VREF
CLK
CLK-IN
BUS2
BUS-DATA
I/O
B/U-C
BUS3
BUS-ON
GND
DATA
D800
MTZJ6.8B
BATT
BUS-IN
BUS1
TH800
RESET
R801 100
RST
RST
Q711
PDTC114EK
+B.U
R800 10k
R802 100
BUS-ON
VCC
A13
Q741
2PD601A
A14
Q740,741
R804
10
R740
22k
IC800
MM1175XFF
+5V REGULATOR
A15
Q800
PDTC114EK
BATTERY
C710
0.1
C742
100
10V
C740
10
16V
D741
HZS6B1L
C741
0.01
DETECT
D805
R811
MTZJ18B 1k
SONY BUS
C801
0.01
INTERFACE
D802
MTZJ18B
D803
MTZJ18B
C800
330
16V
(CHASSIS)
A16
(CHASSIS)
17
17
XR-CA360/CA360X
PRINTED WIRING BOARD – CONTROL Board –
3
4
5
6
7
8
D910 – 912, 914, 916,
D918 – 922, 924, 930, 932,
D934 – 937, 941 – 944
S958
S969
S976
SEEK
A
B
D934,
S957, 975 –
S957
A
D944
A
S981
S955
D936, S955, 978
SEL
D920, S951
DISC –
1
D918, S960
DISC +
2
D910, S961
REP
3
D911, S962
SHUF
4
D912
D932
D912, S963
5
D932, S968
6
K
S973
K
S982
1-686-928-
D914, S965
ATA
BTM
A
A
K
D919, S954
ATT
D915
D914
K
A
K
D920
A
S965
S968
A
K
A
K
D911
K
A
D910
D919
A
D936
D918
A
D933
D937, S956, 979
MODE
S967
S963
S962
A
S961
S960
S951
S954
K
C
S975
K
S978
K
A
D930, S967, 981
DSPL
D930
A
K
S983
S971
S977
S970
D934
D937
K
D916
LCD1
LIQUID CRYSTAL DISPLAY
K
S979
S972
1
56
S959
S956
D943, 944, S972, 983
EQ3
D921
K
(VOLUME)
A
A
K
R917
K
D942
D916, S970, 977
m
.
–
A
D935
D941
A
K
D935,
S958, 974
+
K
A
D941, 942, S959, 980
SOURCE
K
S980
10
D921, S969, 976
+
>
M
CONTROL BOARD (COMPONENT SIDE)
S974
9
A D943
A
2
K
1
R918
5-5.
D922
D922, S971, 982
SENS
A
D
11
D924
K
A
(11)
D924, S973
OFF
MAIN BOARD
CN600
(Page 15)
CONTROL BOARD (CONDUCTOR SIDE)
D963
R960
D940
R961
11
R911
41
1
CN900
12
R920
2
R900
40
1
(LCD BACK LIGHT)
K
R910
C955
C954
IC900
80
A
R905
A
E
K
60
R921
R955
61
C952
A
R954
K
A
D960
C953
K
D962
R904
D964
R903
20
21
R914
A
R915
R912 R913
R916
R931
R932
R964
R934
R965
R935
F
R966
R933
R967
R930
K
R902
R901
D961
R963
R962
1-686-928-
• Semiconductor Location
Ref. No.
D910
D911
D912
D914
D916
D918
D919
D920
D921
D922
Location
C-5
C-6
C-6
C-7
B-9
C-5
C-3
C-4
B-9
C-9
Ref. No.
Location
Ref. No.
Location
D924
D930
D932
D934
D935
D936
D937
D940
D941
D942
C-10
C-10
C-7
B-2
B-2
C-2
C-1
E-3
B-1
B-1
D943
D944
D960
D961
D962
D963
D964
B-10
B-9
E-2
F-2
D-4
D-7
E-10
IC900
E-5
18
18
11
(11)
XR-CA360/CA360X
SCHEMATIC DIAGRAM – CONTROL Board –
• See page 20 for Waveform.
COM2
COM2
COM1
COM4
COM3
COM3
S51
S50
S51
S50
S43
COM4
S48
S49
S49
S46
S47
S48
S46
S47
S44
S43
S42
S45
S45
S44
S42
S43
S40
S41
S39
S39
S40
S41
S38
S37
S37
S38
S36
S35
S35
S36
S33
S34
S34
S31
S32
S32
S31
S33
S30
S29
S28
S29
S30
S27
S27
S28
S25
S26
S26
S23
S24
S25
S23
S24
S21
S22
S20
S19
S18
S17
S16
S15
S14
S955,978
S951
S44
∗
S12
S11
S10
S9
S8
S7
S6
S5
S3
R962
S22
R920
100
S20
R910
100
S21
R912
100
S19
R915
100
S18
R931
100
S17
R934
100
S16
R966
220
S15
R961
220
S14
∗
S13
R921
∗
S12
R911
∗
S10
R913
∗
S9
R916
∗
S8
R932
∗
S7
R935
∗
S6
R965
S5
R960
220
S13
∗ R962
22 (CA360)
180 (CA360X)
S4
270 (CA360X)
S11
∗ R911,913
S2
120 (CA360)
270 (CA360X)
S4
∗ R916,921,932
S1
150 (CA360)
330 (CA360X)
S3
∗ R935
150 (CA360)
S2
∗ R965
22 (CA360)
180 (CA360X)
COM1
LCD1
LIQUID CRYSTAL DISPLAY
S1
S960
SEL
DISC -
D921
1
R967
220
R933
100
R930
100
+
R914
100
DISC +
S955
2
S978
S969
S976
R963
220
S969,976
D921
∗
+
R918
100
R917
100
R964
220
S956,979
D932
∗
SEEK
S961
S965
MODE
6
S956
S979
REP
ATA
3
BTM
S970
S977
D916
∗
SEEK
D916
-
D940
NSPW310BS
D935
D919
D912
∗
∗
∗
+
ATT
5
(LCD BACK LIGHT)
D930
∗
D944
∗
S957,975
DSPL
D943,944
∗
S958,974
D961
1SS355
CL-190PG-CD (CA360)
CL-190SR-CD (CA360X)
D963
1SS355
S42
S43
S44
S45
D964
1SS355
S959,980
R901 1k
R902 1k
LCD-DI(TX)
R903 1k
LCD-CE
R904 1k
SOURCE
S973
D960
1SS355
OFF
S959
S980
D962
1SS355
R905 1k
S45
LCD-CLK
LCD-DO(RX)
S46
∗ D941-944
S46
CL-170SR-CD (CA360X)
3
S47
LCD-RESET
REP
BTM
S48
CL-170PG-CD (CA360)
ATA
2
S983
∗
S49
LAMP+B
DISC +
D922
SENS
S51
918-922,924,930,932,934-937
∗
S50
∗ D910-912,914,916,
D910
∗
S52
FRASH WRITE
D914
∗
S53
SEL
R900
0
D918
COM1
∗
S972
COM2
D933
6
COM3
∗
5
S47
EQ3
S974
KS5
D936
S958
S968
S48
ATT
GND
S972,983
S963
S49
4
D943
∗
OFF
S50
1
D924
S51
SHUF
COM1
∗
∗
COM2
D915
+(VOLUME)
∗
-
COM3
∗
DISC -
S954
D941
S982
D911
SOURCE
GND
S971
COM4
-
S981
KS1
∗
S967
COM4
D934
∗
4
S975
KS2
D937
MODE
S957
D941,942
BU+5V
S970,977
KS3
∗
(Page 16)
SENS
KS4
D942
LAMP+B
S971,982
DSPL
EQ3
D920
NOSE SW
S967,981
SHUF
(VOLUME)
CN900
12P
S962
-(VOLUME)
KS6
S42
KI1
S41
KI2
S40
KI3
S39
S41
∗ D915, 933
100 (CA360)
S40
120 (CA360X)
S39
S38
KI4
S38
KI5
S37
VDD
S36
VLCD
S35
C954
0.047
VLCD1
S34
C955
0.047
VLCD2
LIQUID CRYSTAL
S33
VSS
DISPLAY DRIVER
S32
TEST
IC900
LC75884W
S31
S37
S36
R955 0
S35
C953
0.47
C952
680p
(CHASSIS)
R954
43k
S34
S33
S32
S31
S30
OSC
S30
RES
S29
DO
S28
CE
S27
CL
S26
DI
S25
S1
S24
S2
S23
S29
S28
S27
S26
S25
S24
19
19
S22
S21
S22
S20
S21
S18
S19
S20
S19
S18
S17
S17
S16
S15
S14
S15
S14
S16
S13
S12
S11
S12
S13
S10
S11
S9
S10
S7
S8
S9
S8
S7
S6
S6
S5
S5
S4
S3
S2
S3
S4
S23
S1
5-6.
XR-CA360/CA360X
• Waveforms
– MAIN Board –
– CONTROL Board –
• IC Block Diagrams
– MAIN Board –
1 IC1 qs (OSC2)
3 IC900 ud (OSC)
IC400
3.1 Vp-p
DGND
SDA
SCL
MUTE
SEL
ADJ
VCC
OUTF1
OUTR1
OUTF2
OUTR2
22
21
20
19
18
17
16
15
14
13
12
2
VCO
FADER
(0 ∼ –58,
– ∞ dB)
FADER
(0 ∼ –58,
– ∞ dB)
FADER
(0 ∼ –58,
– ∞ dB)
TONE
PASS
21.1 µs
FADER
(0 ∼ –58,
– ∞ dB)
TONE
PASS
2 IC1 qh (XO)
BASS, TREBLE, MIDDLE
(–15dB ∼ +15dB, 1dB STEP)
VOLUME
(+23 ∼ –79dB, – ∞ dB
1dB STEP)
VOLUME
(+23 ∼ –79dB, – ∞ dB
1dB STEP)
INPUT GAIN
(0 ∼ 15dB, 1dB STEP)
INPUT GAIN
(0 ∼ 15dB, 1dB STEP)
MUTE
MUTE
5.1 Vp-p
INPUT SELECTOR
(4 STEREO INCLUDE 1 ISOLATION INPUT)
30.5 µs
20
20
1
2
3
4
5
6
7
8
9
10
11
AGND
FIL
AP1
AN
AP2
B1
B2
C1
C2
D1
D2
VCC/2
14 VCC
RESET 2
OUT
RESET
SWITCH
13
RESET
IN
BATT 3
BATT
SWITCH
12
BUS ON
IN
CLK
4
OUT
11
CLK
IN
VREF 5
10
BATT
CHECK
DATA
6
IN/OUT
BASS, TREBLE, MIDDLE
(–15dB ∼ +15dB, 1dB STEP)
MM1175XFF
BUS ON 1
OUT
2.4 Vp-p
1 C BUS
LOGIC
54.3 ns
IC800
BD3803F-FE2
GND 7
9 DATA IN
8 DATA OUT
XR-CA360/CA360X
5-7. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC1 MN101C49HAS (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
1
VREF –
—
Description
2
VSM
I
FM and AM signal meter voltage detection input from the tuner unit (A/D input)
3 to 6
NC
I
Not used
7
QUALITY
I
Not used
8
MPTH
I
Not used
9
NC
I
Not used
10
VREF +
—
Reference voltage (+5V) terminal (for A/D converter)
11
VDD
—
Power supply terminal (+5V)
12
OSC2
O
Main system clock output terminal (18.432 MHz)
13
OSC1
I
Main system clock input terminal (18.432 MHz)
Reference voltage (0V) terminal (for A/D converter)
14
VSS
—
15
XI
I
Sub system clock input terminal (32.768 kHz)
16
XO
O
Sub system clock output terminal (32.768 kHz)
Ground terminal
17
MMOD
I
Setting terminal for the single chip mode
18
LCD-SO (TX)
O
LCD serial data output to the liquid crystal display driver
19
LCD-SI (RX)
I
LCD serial data input from the liquid crystal display driver
20
LCD-CKO
O
LCD serial transfer clock signal output to the liquid crystal display driver
21 to 23
NC
O
Not used
24
SYS-RES
O
System reset signal output to the SONY bus interface “L”: reset
25
BUS-ON
O
Bus interface control signal output to the SONY bus interface “L”: uni-link on
26
KEYACK
I
Key acknowledge signal detection input from the liquid crystal display driver
27
DAVN
I
Not used
“L”: single chip (fixed at “L” in this set)
28
BU-IN
I
Battery detection signal input from the bus interface and battery detect circuit
“L” is input at low voltage
29
NC
I
Not used
30
TU-ATTIN
I
Tuner muting on/off control signal input from the tuner unit “L”: muting on
31, 32
NC
I
Not used
33
RESET
I
System reset signal input from the reset signal generator and reset switch “L”: reset
“L”is input for several 100 msec after power on, then it changes to “H”
34
NC
O
Not used
35
BEEP
O
Beep sound drive signal output to the power amplifier “H”: beep on
36
POWER-ON
O
Main system power supply on/off control signal output “H”: power on
37
ILL-IN
I
Illuminate line detection signal input terminal “L”: ill on Not used
38
ACC-IN
I
Accessory detection signal input “L”: accessory on
“H” is input for several 200 msec after accessory on, then it changes to “L”
39
NC
O
Not used
40
TEL-ATT
I
Telephone muting signal input terminal At input of “H”, the signal is attenuated by –20 dB
Not used
41
NCI
I
Not used
42
BUS-SO
O
Serial data output to the SONY bus interface
43
BUS-SI
I
Serial data input from the SONY bus interface
44
BUS-CKO
O
Serial data transfer clock signal output to the SONY bus interface
45
I2C-SIO
I/O
Two-way data bus with the tuner unit and electrical volume
46
NC
O
Not used
47
I2C-CKO
O
Serial data transfer clock signal output to the tuner unit and electrical volume
48
AMP-ON
O
Standby on/off control signal output to the power amplifier
“L”: standby mode, “H”: amplifier on
49
AMP-ATT
O
Muting on/off control signal output to the power amplifier “L”: muting on
21
XR-CA360/CA360X
Pin No.
Pin Name
I/O
Description
50
ATT
O
Audio line muting on/off control signal output “H”: muting on
51 to 53
NC
O
Not used
54
TU-ATT
O
Tuner muting on/off control signal output to the tuner unit “L”: muting on
55, 56
NC
O
Not used
57
LO/DX
O
Local/DX selection signal output terminal “L”: DX, “H”: local Not used
58
TU-ON
O
Tuner system power supply on/off control signal output “H”: tuner power on
59
VOL-ATT
O
Electrical volume muting on/off control signal output to the electrical volume “L”: muting on
60
FM-ON
O
FM system power supply on/off control signal output terminal
“H”: FM power on Not used
61
AM-ON
O
AM system power supply on/off control signal output terminal
“H”: AM power on Not used
62
NC
O
Not used
63
LCD-RES
O
LCD reset signal output to the liquid crystal display driver
64
LCD-CE
O
Chip enable signal output to the liquid crystal display driver
65
FLASH-W
I
Internal flash memory data write mode detection signal input
“L”: data write mode Normally: fixed at “H”
66
TEST-IN
I
Setting terminal for the test mode
“L”: reset
“H” active
“L”: test mode Normally: fixed at “H”
67 to 73
NC
O
Not used
74
EE-SIO
I/O
Two-way data bus with the tuner unit
75
EE-CKO
O
Serial data transfer clock signal output to the tuner unit
76
COL-SEL
I
Illumination color selection signal input “L”: red illumination “H”: green illumination
(XR-CA360: fixed at “H” in this set, XR-CA360X: fixed at “L” in this set)
77 to 82
NC
O
Not used
83
ILL-ON
O
Power on/off control signal output of the illumination LED and LCD back light
“H”: power on
84
DEST-SEL0
I
Destination setting terminal
(E model: fixed at “H” in this set, Saudi Arabia model: fixed at “L” in this set)
85
DEST-SEL1
I
Destination setting terminal (fixed at “H” in this set)
86
DEST-SEL2
I
Destination setting terminal (E model: input terminal for the ferquency select switch,
Saudi Arabia model: fixed at “H” in this set)
87 to 92
NC
O
Not used
93
NOSE-SW
I
Front panel block remove/attach detection signal input
“L”: front panel is attached
94
NS-MASK
O
Not used
95
DAVSS
—
Ground terminal (for D/A converter)
96
TAPE-ON
O
Capstan/reel motor drive signal output “H”: motor on
22
97
N/R
I
Tape direction switch input terminal “L”: reverse direction, “H”: forward direction
98
FF/REW
I
FF/REW detection switch input terminal “L”: FF/REW mode, “H”: PLAYBACK mode
99
TAPE-IN
I
Tape in detection switch input terminal “L”: tape in
100
DAVDD
—
Power supply terminal (+5V) (for D/A converter)
XR-CA360/CA360X
SECTION 6
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Accessories are given in the last of the electrical parts list.
6-1. GENERAL SECTION
not supplied
6
#1
main board section
F901
5
MG-36SZ13-32
#1
9
#1
2
1
not supplied
3
7
4
not supplied
not supplied
8
front panel section
Ref. No.
Part No.
Description
Remark
1
2
3
4
5
3-246-741-01
X-3383-739-1
3-041-581-11
3-044-125-01
3-376-464-11
PANEL, SUB
LOCK ASSY (S)
DOOR, CASSETTE
SPRING, TORSION
SCREW (+PTT 2.6X6), GROUND POINT
6
1-776-207-31 CORD (WITH CONNECTOR) (POWER)
Ref. No.
7
8
9
F901
#1
Part No.
Description
Remark
3-042-244-01
3-246-758-01
3-256-779-01
1-532-877-11
7-685-792-09
SCREW (T)
COLLAR
PLATE (C), GROUND
FUSE (BLADE TYPE) (AUTO FUSE) (10A/32V)
SCREW +PTT 2.6X6 (S)
23
XR-CA360/CA360X
Ver 1.1
6-2. FRONT PANEL SECTION
#4
not supplied
(control board)
not supplied
#4
not supplied
59
58
60
57
not supplied
LCD1
52
55
61
not supplied
62
56
not supplied
not supplied
63
not supplied
53
not supplied
54
51
Ref. No.
Part No.
Description
51
51
52
53
54
A-3337-197-A
A-3337-363-A
X-3383-132-1
3-231-816-01
3-246-738-11
PANEL ASSY, FRONT (CA360X)
PANEL ASSY, FRONT (CA360)
BUTTON KIT (SVX) ASSY
SPRING (RELEASE)
PANEL, FRONT (CA360X)
54
55
56
57
3-246-738-21
3-029-327-01
3-375-372-01
1-780-021-11
PANEL, FRONT (CA360)
SPRING (EJECT)
SPRING (F/R)
CONDUCTIVE BOARD, CONNECTION
24
Remark
Ref. No.
Part No.
Description
58
59
60
61
62
1-786-464-11
3-246-739-01
X-3378-490-2
3-246-744-01
3-246-743-01
SWITCH, SHEET
PANEL, FRONT BACK
CASE (PANEL) ASSY
BUTTON (EJECT) (Z)
BUTTON (REW) (m)
63
LCD1
#4
3-246-742-01 BUTTON (FF) (M)
1-805-131-11 DISPLAY PANEL, LIQUID CRYSTAL
7-685-105-19 SCREW +P 2X8 TYPE2 NON-SLIT
Remark
XR-CA360/CA360X
Ver 1.2
6-3. MAIN BOARD SECTION
101
#3
102
#3
main board
not supplied
TU100
Ref. No.
101
101
101
Part No.
Description
Remark
A-3274-648-A MAIN BOARD, COMPLETE (CA360X)
A-3274-708-A MAIN BOARD, COMPLETE (CA360: E)
A-3274-711-A MAIN BOARD, COMPLETE
(CA360: Saudi Arabia)
Ref. No.
Part No.
* 102
TU100
#3
3-041-578-01 BRACKET (IC)
A-3220-944-A TUNER UNIT (TUX-031//Q2)
7-685-794-09 SCREW +PTT 2.6X10 (S)
Description
Remark
25
XR-CA360/CA360X
6-4. MECHANISM DECK SECTION
(MG-36SZ13-32)
159
#9
161
160
not supplied
158
155
157
#8
162
163
not supplied
HP901
not supplied
M901
not supplied
156
156
154
156
S902
S903
#10
164
153
not supplied
165
not supplied
#7
S901
159
not supplied
(slide SW board)
not supplied
167
159
#6
#7
167
152
not supplied
not supplied
not supplied
#7
#7
151
#5
Part No.
Description
Part No.
Description
151
152
153
154
155
3-246-754-01
3-045-943-01
3-045-945-01
3-045-953-01
3-045-940-01
BRACKET (MD)
MAIN BELT
SUB BELT (C)
+MACHINE SCREW M1.7X6
PINCH ARM SPG (R)
165
167
169
HP901
M901
3-713-786-51
3-045-893-01
A-3220-926-B
1-500-661-11
1-763-507-11
SCREW +P 2X3
REEL SPINDLE
MECHANISM DECK ASSY (MG-36SZ13-32)
HEAD, MAGNETIC (PLAYBACK)
MOTOR, DC (CAPSTAN/REEL)
156
157
158
159
160
3-045-950-01
3-045-890-01
3-045-933-01
3-045-949-01
3-045-932-01
E-RING (DIA. 2)
PINCH ARM (R)
ADJUSTER ARM SPG (B)
PSW (REEL) B
ADJUSTER ARM SPG (A)
S901
S902
S903
#5
#6
1-771-928-11
1-771-926-11
1-771-927-11
7-621-775-10
7-627-854-08
SWITCH, SLIDE (DIRECTION)
SWITCH, LEAF (FF/REW)
SWITCH, LEAF (TAPE DETECT)
SCREW +B 2.6X4
PRECISION SCREW +P 2X2.5 TYPE 3
161
162
163
164
3-045-939-01
3-045-891-01
3-045-906-01
3-045-952-01
PINCH ARM SPG (F)
PINCH ARM (F)
ADJUSTER SHIM (X)
+MACHINE SCREW M1.7X4
#7
#8
#9
#10
7-685-101-11
7-621-255-35
7-621-772-18
7-685-781-09
SCREW +PTP 2X3 NON-SLIT
SCREW +P 2X5
SCREW +P 2X4
SCREW +PTT 2X4 (S)
Ref. No.
26
Remark
Ref. No.
169
Remark
XR-CA360/CA360X
Ver 1.1
SECTION 7
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Abbreviation
EA : Saudi Arabia model
Ref. No.
Part No.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
Description
Remark
CONTROL BOARD
**************
1-780-021-11 CONDUCTIVE BOARD, CONNECTION
1-786-464-11 SWITCH, SHEET
< CAPACITOR >
C952
C953
C954
C955
1-115-412-11
1-107-823-11
1-165-176-11
1-165-176-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
680PF
0.47uF
0.047uF
0.047uF
5%
10%
10%
10%
25V
16V
16V
16V
< CONNECTOR >
CN900
1-794-312-11 PIN, CONNECTOR 12P
< RESISTOR/DIODE >
D910
D910
D911
D911
D912
8-719-033-14
8-719-078-39
8-719-033-14
8-719-078-39
8-719-033-14
D912
D914
D914
D915
8-719-078-39
8-719-033-14
8-719-078-39
1-216-025-11
D915
D916
LED
LED
LED
LED
LED
CL-170PG-CD-T (REP, 3) (CA360)
CL-170SR-CD-T (REP, 3) (CA360X)
CL-170PG-CD-T (SHUF, 4) (CA360)
CL-170SR-CD-T (SHUF, 4) (CA360X)
CL-170PG-CD-T (5) (CA360)
LED CL-170SR-CD-T (5) (CA360X)
LED CL-170PG-CD-T (ATA, BTM) (CA360)
LED CL-170SR-CD-T (ATA, BTM) (CA360X)
RES-CHIP
100
5%
1/10W
(CA360)
1-216-027-00 RES-CHIP
120
5%
1/10W
(CA360X)
D918
D918
D919
8-719-033-14 LED CL-170PG-CD-T (– m ., SEEK)
(CA360)
8-719-078-39 LED CL-170SR-CD-T (– m ., SEEK)
(CA360X)
8-719-033-14 LED CL-170PG-CD-T (DISC +, 2) (CA360)
8-719-078-39 LED CL-170SR-CD-T (DISC +, 2) (CA360X)
8-719-033-14 LED CL-170PG-CD-T (ATT) (CA360)
D919
D920
D920
D921
8-719-078-39
8-719-033-14
8-719-078-39
8-719-033-14
D916
Ref. No.
D922
D922
D924
LED
LED
LED
LED
CL-170SR-CD-T (ATT) (CA360X)
CL-170PG-CD-T (DISC –, 1) (CA360)
CL-170SR-CD-T (DISC –, 1) (CA360X)
CL-170PG-CD-T (+ M >)
(CA360)
8-719-078-39 LED CL-170SR-CD-T (+ M >)
(CA360X)
8-719-033-14 LED CL-170PG-CD-T (SENS) (CA360)
8-719-078-39 LED CL-170SR-CD-T (SENS) (CA360X)
8-719-033-14 LED CL-170PG-CD-T (OFF) (CA360)
Part No.
When indicating parts by reference
number, please include the board.
Description
Remark
D924
D930
8-719-078-39 LED CL-170SR-CD-T (OFF) (CA360X)
8-719-033-14 LED CL-170PG-CD-T (DSPL)(CA360)
D930
D932
D932
D933
8-719-078-39
8-719-033-14
8-719-078-39
1-216-025-11
D933
LED CL-170SR-CD-T (DSPL) (CA360X)
LED CL-170PG-CD-T (6) (CA360)
LED CL-170SR-CD-T (6) (CA360X)
RES-CHIP
100
5%
1/10W
(CA360)
1-216-027-00 RES-CHIP
120
5%
1/10W
(CA360X)
D934
D934
D935
D935
D936
8-719-033-14
8-719-078-39
8-719-033-14
8-719-078-39
8-719-033-14
LED
LED
LED
LED
LED
CL-170PG-CD-T (– (VOLUME)) (CA360)
CL-170SR-CD-T (– (VOLUME)) (CA360X)
CL-170PG-CD-T (+ (VOLUME)) (CA360)
CL-170SR-CD-T (+ (VOLUME)) (CA360X)
CL-170PG-CD-T (SEL) (CA360)
D936
D937
D937
D940
D941
8-719-078-39
8-719-033-14
8-719-078-39
6-500-491-01
8-719-038-07
LED
LED
LED
LED
LED
CL-170SR-CD-T (SEL) (CA360X)
CL-170PG-CD-T (MODE) (CA360)
CL-170SR-CD-T (MODE) (CA360X)
NSPW310BST (LCD BACK LIGHT)
CL-190PG-CD-T (SOURCE) (CA360)
D941
D942
D942
D943
D943
8-719-061-16
8-719-038-07
8-719-061-16
8-719-038-07
8-719-061-16
LED
LED
LED
LED
LED
CL-190SR-CD-T (SOURCE) (CA360X)
CL-190PG-CD-T (SOURCE) (CA360)
CL-190SR-CD-T (SOURCE) (CA360X)
CL-190PG-CD-T (EQ3) (CA360)
CL-190SR-CD-T (EQ3) (CA360X)
D944
D944
D960
D961
D962
8-719-038-07
8-719-061-16
8-719-988-61
8-719-988-61
8-719-988-61
LED CL-190PG-CD-T (EQ3) (CA360)
LED CL-190SR-CD-T (EQ3) (CA360X)
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
D963
D964
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
< IC >
IC900
D921
CONTROL
8-759-657-06 IC LC75884W
< LIQUID CRYSTAL DISPLAY >
LCD1
1-805-131-11 DISPLAY PANEL, LIQUID CRYSTAL
< RESISTOR >
R900
R901
R902
R903
1-216-864-11
1-216-821-11
1-216-821-11
1-216-821-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
1K
1K
1K
5%
5%
5%
1/10W
1/10W
1/10W
27
XR-CA360/CA360X
Ver 1.1
CONTROL
Ref. No.
Part No.
MAIN
Description
Remark
Ref. No.
Part No.
Description
Remark
R904
1-216-821-11 METAL CHIP
1K
5%
1/10W
7-685-794-09 SCREW +PTT 2.6X10 (S)
R905
R910
R911
1-216-821-11 METAL CHIP
1-216-025-11 RES-CHIP
1-216-027-00 RES-CHIP
1K
100
120
5%
5%
5%
< JACK >
R911
1-216-814-11 METAL CHIP
270
5%
R912
1-216-025-11 RES-CHIP
100
5%
1/10W
1/10W
1/10W
(CA360)
1/10W
(CA360X)
1/10W
R913
1-216-027-00 RES-CHIP
120
5%
R913
1-216-814-11 METAL CHIP
270
5%
R914
R915
R916
1-216-025-11 RES-CHIP
1-216-025-11 RES-CHIP
1-216-029-00 RES-CHIP
100
100
150
5%
5%
5%
R916
1-216-814-11 METAL CHIP
270
5%
R917
R918
R920
R921
1-216-809-11
1-216-809-11
1-216-025-11
1-216-029-00
100
100
100
150
5%
5%
5%
5%
R921
1-216-035-00 RES-CHIP
270
5%
R930
R931
R932
1-216-025-11 RES-CHIP
1-216-025-11 RES-CHIP
1-216-029-00 RES-CHIP
100
100
150
5%
5%
5%
R932
1-216-035-00 RES-CHIP
270
5%
R933
R934
R935
1-216-025-11 RES-CHIP
1-216-025-11 RES-CHIP
1-216-029-00 RES-CHIP
100
100
150
5%
5%
5%
R935
1-216-815-11 METAL CHIP
330
5%
R954
1-218-731-11 METAL CHIP
43K
0.5%
R955
R960
R961
R962
1-216-864-11
1-216-033-00
1-216-033-00
1-216-009-00
0
220
220
22
5%
5%
5%
R962
1-216-031-00 RES-CHIP
180
5%
R963
R964
R965
1-216-033-00 RES-CHIP
1-216-033-00 RES-CHIP
1-216-009-00 RES-CHIP
220
220
22
5%
5%
5%
R965
1-216-812-11 METAL CHIP
180
5%
R966
1-216-813-11 METAL CHIP
220
5%
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1/10W
(CA360)
1/10W
(CA360X)
1/10W
1/10W
1/10W
(CA360)
1/10W
(CA360X)
1/10W
1/10W
1/10W
1/10W
(CA360)
1/10W
(CA360X)
1/10W
1/10W
1/10W
(CA360)
1/10W
(CA360X)
1/10W
1/10W
1/10W
(CA360)
1/10W
(CA360X)
1/10W
1/10W
1/10W
1/10W
(CA360)
1/10W
(CA360X)
1/10W
1/10W
1/10W
(CA360)
1/10W
(CA360X)
1/10W
R967
1-216-813-11 METAL CHIP
220
5%
1/10W
************************************************************
A-3274-648-A MAIN BOARD, COMPLETE (CA360X)
A-3274-708-A MAIN BOARD, COMPLETE (CA360: E)
A-3274-711-A MAIN BOARD, COMPLETE (EA)
*********************
*
28
3-041-578-01 BRACKET (IC)
ANT100 1-815-185-13 JACK (ANT) (FM/AM ANTENNA)
< CAPACITOR >
C1
C2
C3
C4
C5
1-162-916-11
1-162-916-11
1-162-918-11
1-162-919-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
12PF
12PF
18PF
22PF
0.1uF
5%
5%
5%
5%
10%
50V
50V
50V
50V
16V
C6
C7
C8
C81
C100
1-124-234-00
1-125-701-11
1-162-964-11
1-107-826-11
1-165-176-11
ELECT
DOUBLE LAYER
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.047F
0.001uF
0.1uF
0.047uF
20%
10%
10%
10%
10V
5.5V
50V
16V
16V
C101
1-162-964-11 CERAMIC CHIP
0.001uF
10%
50V
C104
C105
C106
C250
1-164-156-11
1-164-156-11
1-124-584-00
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
0.1uF
100uF
0.01uF
20%
10%
25V
25V
10V
25V
C251
C262
C302
C303
C304
1-126-157-11
1-165-908-11
1-162-964-11
1-162-964-11
1-162-927-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
1uF
0.001uF
0.001uF
100PF
20%
10%
10%
10%
5%
16V
10V
50V
50V
50V
C305
C306
C307
C310
C311
1-162-927-11
1-162-970-11
1-162-970-11
1-104-942-11
1-164-315-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
100PF
0.01uF
0.01uF
1uF
470PF
5%
10%
10%
20%
5%
50V
25V
25V
50V
50V
C312
C314
C315
C400
C401
1-124-584-00
1-124-584-00
1-124-584-00
1-125-891-11
1-125-891-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
100uF
100uF
100uF
0.47uF
0.47uF
20%
20%
20%
10%
10%
10V
6.3V
6.3V
10V
10V
C402
C403
C404
C405
C409
1-125-891-11
1-125-891-11
1-125-891-11
1-125-891-11
1-126-157-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.47uF
0.47uF
0.47uF
0.47uF
10uF
10%
10%
10%
10%
20%
10V
10V
10V
10V
16V
C410
C411
C412
C413
C414
1-124-589-11
1-162-970-11
1-162-915-11
1-162-915-11
1-162-915-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
0.01uF
10PF
10PF
10PF
20%
10%
0.5PF
0.5PF
0.5PF
16V
25V
50V
50V
50V
C415
C416
C417
C418
C419
1-162-915-11
1-126-163-11
1-126-163-11
1-126-163-11
1-126-163-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
10PF
4.7uF
4.7uF
4.7uF
4.7uF
0.5PF
20%
20%
20%
20%
50V
50V
50V
50V
50V
C420
C421
C422
C423
C424
1-125-891-11
1-125-891-11
1-125-891-11
1-125-891-11
1-125-891-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47uF
0.47uF
0.47uF
0.47uF
0.47uF
10%
10%
10%
10%
10%
10V
10V
10V
10V
10V
(EA)
XR-CA360/CA360X
Ver 1.2
MAIN
Ref. No.
Part No.
Description
C425
C426
C427
C428
C429
1-125-891-11
1-125-891-11
1-125-891-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47uF
0.47uF
0.47uF
100PF
100PF
10%
10%
10%
5%
5%
10V
10V
10V
50V
50V
Remark
C430
C431
C451
C452
C500
1-162-967-11
1-162-967-11
1-124-589-11
1-109-982-11
1-126-157-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0.0033uF
0.0033uF
47uF
1uF
10uF
10%
10%
20%
10%
20%
50V
50V
16V
10V
16V
C503
C505
C507
C508
C520
1-162-964-11
1-126-157-11
1-107-826-11
1-107-826-11
1-162-923-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
10uF
0.1uF
0.1uF
47PF
10%
20%
10%
10%
5%
50V
16V
16V
16V
50V
C521
C522
C523
C600
C601
1-162-923-11
1-162-923-11
1-162-923-11
1-164-156-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47PF
47PF
47PF
0.1uF
0.1uF
5%
5%
5%
50V
50V
50V
25V
16V
C650
C700
C701
C710
C730
1-104-942-11
1-126-936-11
1-165-128-11
1-107-826-11
1-126-157-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
1uF
3300uF
0.22uF
0.1uF
10uF
20%
20%
10%
20%
50V
16V
16V
16V
16V
C731
C732
C733
C734
C740
1-165-176-11
1-165-908-11
1-164-315-11
1-165-908-11
1-126-157-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.047uF
1uF
470PF
1uF
10uF
10%
10%
5%
10%
20%
16V
10V
50V
10V
16V
C741
C742
C800
C801
1-162-970-11
1-124-584-00
1-126-940-11
1-162-970-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
0.01uF
100uF
330uF
0.01uF
10%
20%
20%
10%
25V
10V
25V
25V
10%
Ref. No.
Part No.
Description
Remark
D650
8-719-110-49 DIODE RD18ESB2
D651
D653
D700
D721
D722
8-719-991-33
8-719-109-93
8-719-049-38
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
RD6.2ESB2
1N5404TU
11ES2
11ES2
D723
D724
D731
D741
D742
8-719-200-82
8-719-200-82
8-719-110-14
8-719-935-39
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
11ES2
RD9.1ESB3
HZS6B1LTD
1SS133T-77
D800
D802
D803
D805
8-719-109-97
8-719-110-49
8-719-110-49
8-719-110-49
DIODE
DIODE
DIODE
DIODE
RD6.8ESB2
RD18ESB2
RD18ESB2
RD18ESB2
< IC >
IC1
IC2
IC300
IC400
IC500
6-803-178-01
6-701-405-01
6-802-510-01
6-703-302-02
8-759-827-12
IC
IC
IC
IC
IC
MN101C49HEA
PST3443UL
HA12232FP-EL
BD3803AF-FE2
TA8272H
IC800
8-759-096-16 IC MM1175XFF
< SHORT >
* CN300
* CN350
CN400
CN600
CN700
CN800
1-564-705-11
1-573-486-11
1-774-699-12
1-794-311-21
1-774-701-11
JC30
JC44
JC49
JC52
JC53
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
< CONNECTOR >
JC83
JC91
JC104
JC110
JC132
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
PIN, CONNECTOR (PC BOARD) 3P
PIN, CONNECTOR (PC BOARD) 8P
JACK, PIN 4P (BUS AUDIO IN, AUDIO OUT)
PLUG, CONNECTOR 12P
PIN, CONNECTOR 16P
JC133
JC134
JC147
JC148
JC166
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC169
JC170
JC173
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
0
0
0
1-580-907-31 PLUG, CONNECTOR (BUS CONTROL IN)
< DIODE >
D250
D253
D300
D350
D451
8-719-921-42
8-719-991-33
8-719-991-33
8-719-200-82
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
MTZJ-5.1A
1SS133T-77
1SS133T-77
11ES2
1SS133T-77
D452
D500
D501
D502
D503
8-719-110-03
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
RD7.5ESB2
11ES2
11ES2
11ES2
11ES2
D504
D505
D506
D507
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
11ES2
11ES2
11ES2
11ES2
< COIL >
L1
L700
1-410-509-11 INDUCTOR
1-419-476-11 COIL, CHOKE
10uH
250uH
< TRANSISTOR >
When replacing the IC1, refer to servicing note
(Page 2 “When replacing the IC1”).
Q251
Q252
Q253
Q350
Q351
8-729-920-85
8-729-049-85
8-729-043-27
8-729-205-95
8-729-043-27
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD1664-QR
2PB710AR-115
PDTC114EK-115
2SA1428-Y
PDTC114EK-115
Q400
Q401
Q402
8-729-920-21 TRANSISTOR
8-729-920-21 TRANSISTOR
8-729-920-21 TRANSISTOR
DTC314TK-T-146
DTC314TK-T-146
DTC314TK-T-146
29
XR-CA360/CA360X
MAIN
Ref. No.
Part No.
Description
Remark
Q403
Q450
8-729-920-21 TRANSISTOR
8-729-043-32 TRANSISTOR
DTC314TK-T-146
PDTA114EK-115
Q451
Q650
Q651
Q710
Q711
8-729-043-29
8-729-422-33
8-729-216-22
8-729-205-95
8-729-043-27
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
PDTC144EK-115
2SD601A-Q-TX
2SA1162-G
2SA1428-Y
PDTC114EK-115
Q722
Q724
Q725
Q726
Q730
8-729-205-95
8-729-205-95
8-729-043-27
8-729-043-27
8-729-921-48
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1428-Y
2SA1428-Y
PDTC114EK-115
PDTC114EK-115
2SD1760F5-Q
Q731
Q732
Q740
Q741
Q800
8-729-216-22
8-729-043-27
8-729-205-95
8-729-422-33
8-729-043-27
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1162-G
PDTC114EK-115
2SA1428-Y
2SD601A-Q-TX
PDTC114EK-115
< RESISTOR >
R1
R2
R3
R4
R5
1-216-821-11
1-216-864-11
1-216-845-11
1-216-829-11
1-216-809-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
0
100K
4.7K
100
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R6
R7
R8
R9
R10
1-216-809-11
1-249-417-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
100
1K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
1/10W
R11
R12
R13
R14
R16
1-216-809-11
1-249-441-11
1-216-809-11
1-216-845-11
1-216-845-11
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
100
100K
100
100K
100K
5%
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
1/10W
R17
R18
R19
R20
R21
1-216-841-11
1-216-809-11
1-247-807-31
1-247-807-31
1-216-809-11
METAL CHIP
METAL CHIP
CARBON
CARBON
METAL CHIP
47K
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/4W
1/10W
R22
R23
R24
R25
R26
1-216-809-11
1-216-833-11
1-216-833-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
10K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R27
R28
R29
1-247-807-31 CARBON
1-216-864-11 SHORT CHIP
1-216-845-11 METAL CHIP
100
5%
0 (CA360X)
100K
5%
R30
R31
1-216-864-11 SHORT CHIP
1-216-845-11 METAL CHIP
0 (EA)
100K
5%
1/10W
(E)
R33
R35
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
100K
100K
5%
5%
R36
1-216-845-11 METAL CHIP
100K
5%
R37
R38
1-216-845-11 METAL CHIP
1-249-441-11 CARBON
100K
100K
5%
5%
1/10W
1/10W
(EA)
1/10W
(E)
1/10W
1/4W
30
Ref. No.
Part No.
Description
R39
R40
R41
R42
R43
1-249-441-11
1-249-441-11
1-216-864-11
1-216-864-11
1-216-864-11
CARBON
CARBON
SHORT CHIP
SHORT CHIP
SHORT CHIP
100K
100K
0
0
0
5%
5%
1/4W
1/4W
Remark
R44
R46
R47
R48
R49
1-247-807-31
1-247-807-31
1-216-809-11
1-247-807-31
1-216-809-11
CARBON
CARBON
METAL CHIP
CARBON
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/10W
1/4W
1/10W
R50
R53
R54
R55
R56
1-247-807-31
1-247-807-31
1-216-809-11
1-216-809-11
1-216-864-11
CARBON
CARBON
METAL CHIP
METAL CHIP
SHORT CHIP
100
100
100
100
0
5%
5%
5%
5%
1/4W
1/4W
1/10W
1/10W
R57
R58
R59
R60
R81
1-216-864-11
1-249-417-11
1-249-417-11
1-216-809-11
1-216-845-11
SHORT CHIP
CARBON
CARBON
METAL CHIP
METAL CHIP
0
1K
1K
100
100K
5%
5%
5%
5%
1/4W
1/4W
1/10W
1/10W
R101
R102
R105
R106
R205
1-216-837-11
1-249-387-11
1-216-813-11
1-216-813-11
1-216-864-11
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
SHORT CHIP
22K
3.3
220
220
0
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
R250
R259
R262
R263
R264
1-216-817-11
1-216-833-11
1-216-821-11
1-216-797-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
10K
1K
10
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R300
R301
R302
R303
R304
1-216-841-11
1-216-841-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R305
R306
R307
R308
R309
1-216-809-11
1-216-806-11
1-216-806-11
1-216-851-11
1-216-851-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
56
56
330K
330K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R310
R311
R312
R313
R314
1-216-835-11
1-216-835-11
1-249-417-11
1-249-417-11
1-216-797-11
METAL CHIP
METAL CHIP
CARBON
CARBON
METAL CHIP
15K
15K
1K
1K
10
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/4W
1/10W
R350
R351
R352
R353
R400
1-216-833-11
1-249-419-11
1-249-419-11
1-217-671-11
1-216-797-11
METAL CHIP
CARBON
CARBON
RES-CHIP
METAL CHIP
10K
1.5K
1.5K
1
10
5%
5%
5%
5%
5%
1/10W
1/4W
1/4W
1/10W
1/10W
R401
R402
R403
R404
R405
1-216-840-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
39K
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R406
R407
R408
1-216-841-11 METAL CHIP
1-216-841-11 METAL CHIP
1-216-841-11 METAL CHIP
47K
47K
47K
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
1/10W
(CA360)
XR-CA360/CA360X
Ver 1.1
MAIN
Ref. No.
Part No.
Description
Remark
R409
R410
1-216-841-11 METAL CHIP
1-216-833-11 METAL CHIP
47K
10K
5%
5%
1/10W
1/10W
R411
R412
R413
R414
R415
1-216-833-11
1-216-833-11
1-216-833-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R416
R417
R418
R419
R420
1-216-833-11
1-216-833-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R421
R422
R423
R450
R451
1-216-809-11
1-216-864-11
1-216-864-11
1-216-805-11
1-216-833-11
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
100
0
0
47
10K
5%
1/10W
5%
5%
1/10W
1/10W
R452
R500
R501
R502
R503
1-216-829-11
1-216-841-11
1-216-825-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47K
2.2K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R505
R600
R601
R602
R603
1-216-864-11
1-249-417-11
1-249-417-11
1-249-417-11
1-249-417-11
SHORT CHIP
CARBON
CARBON
CARBON
CARBON
0
1K
1K
1K
1K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
R604
R605
R606
R607
R650
1-249-417-11
1-249-417-11
1-249-417-11
1-216-821-11
1-249-425-11
CARBON
CARBON
CARBON
METAL CHIP
CARBON
1K
1K
1K
1K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/10W
1/4W
R651
R652
R653
R654
R655
1-216-841-11
1-216-841-11
1-216-829-11
1-216-845-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
4.7K
100K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R656
R657
R663
R664
R710
1-216-838-11
1-216-809-11
1-216-845-11
1-216-821-11
1-260-300-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
27K
100
100K
1K
4.7
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/2W
R711
R712
R713
R720
R721
1-249-419-11
1-249-419-11
1-216-833-11
1-216-833-11
1-247-749-11
CARBON
CARBON
METAL CHIP
METAL CHIP
CARBON
1.5K
1.5K
10K
10K
560
5%
5%
5%
5%
5%
1/4W
1/4W
1/10W
1/10W
1/2W
R722
R725
R728
R730
R731
1-216-864-11
1-247-749-11
1-216-833-11
1-216-833-11
1-249-421-11
SHORT CHIP
CARBON
METAL CHIP
METAL CHIP
CARBON
0
560
10K
10K
2.2K
5%
5%
5%
5%
1/2W
1/10W
1/10W
1/4W
R732
R740
R800
R801
R802
1-216-817-11
1-216-837-11
1-216-833-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
22K
10K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Ref. No.
Part No.
Description
R804
R811
R814
R815
R852
1-216-797-11
1-249-417-11
1-216-849-11
1-216-864-11
1-216-864-11
METAL CHIP
CARBON
METAL CHIP
SHORT CHIP
SHORT CHIP
R853
1-216-864-11 SHORT CHIP
Remark
10
1K
220K
0
0
5%
5%
5%
1/10W
1/4W
1/10W
0
< SWITCH >
S1
SW1
1-692-431-21 SWITCH, TACTILE (RESET)
1-572-552-11 SWITCH, SLIDE (FREQUENCY SELECT) (E)
< TUNER UNIT >
TU100
A-3220-944-A TUNER UNIT (TUX-031//Q2)
< THERMISTOR >
TH700
TH701
TH800
1-801-726-11 THERMISTOR, POSITIVE
1-801-726-11 THERMISTOR, POSITIVE
1-801-792-21 THERMISTOR, POSITIVE
< VIBRATOR >
X1
1-795-539-11 VIBRATOR, CRYSTAL (18.432MHz)
X2
1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
**************************************************************
MISCELLANEOUS
**************
6
57
58
169
F901
1-776-207-31
1-780-021-11
1-786-464-11
A-3220-926-B
1-532-877-11
CORD (WITH CONNECTOR) (POWER)
CONDUCTIVE BOARD, CONNECTION
SWITCH, SHEET
MECHANISM DECK ASSY (MG-36SZ13-32)
FUSE (BLADE TYPE) (AUTO FUSE) (10A/32V)
HP901
LCD1
M901
S901
S902
1-500-661-11
1-805-131-11
1-763-507-11
1-771-928-11
1-771-926-11
HEAD, MAGNETIC (PLAYBACK)
DISPLAY PANEL, LIQUID CRYSTAL
MOTOR, DC (CAPSTAN/REEL)
SWITCH, SLIDE (DIRECTION)
SWITCH, LEAF (FF/REW)
S903
1-771-927-11 SWITCH, LEAF (TAPE DETECT)
************************************************************
ACCESSORIES
************
3-246-852-22 MANUAL, INSTRUCTION (ENGLISH, SPANISH,
TRADITIONAL CHINESE) (E)
3-246-852-32 MANUAL, INSTRUCTION (ENGLISH, ARABIC)
(EA)
3-246-853-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
SPANISH, TRADITIONAL CHINESE) (E)
3-246-853-31 MANUAL, INSTRUCTION, INSTALL
(ENGLISH, ARABIC) (EA)
************************************************************
31
XR-CA360/CA360X
Ref. No.
Part No.
Description
Remark
PARTS FOR INSTALLATION AND CONNECTIONS
**************************************
501
502
503
504
505
X-3382-647-1
3-246-758-01
1-776-207-31
3-246-471-01
X-3382-759-1
501
FRAME ASSY, FITTING
COLLAR
CORD (WITH CONNECTOR) (POWER)
KEY (FRAME)
SCREW ASSY (4), FITTING
502
FITTING FRAME ASSY
×1
503
COLLAR
×1
504
POWER CORD
×1
KEY (FRAME)
×2
505
+K5 × 8
×4
FITTING SCREW
×1
BUSHING
×1
SCREW ASSY (4), FITTING
32
Ref. No.
Part No.
Description
Remark
XR-CA360/CA360X
E Model
XR-CA360/CA360X
Saudi Arabia Model
SERVICE MANUAL
XR-CA360
Ver 1.2 2003.12
SUPPLEMENT-1
File this supplement with the service manual.
Subject: Change of MAIN board.
(ECN-CSA07576)
In this set, MAIN board have been changed in the midway of production.
Printed wiring boards and schematic diagrams of type B, and changed parts list are described in
this supplement-1.
Refer to original service manual for other information.
• TYPE A/B DISCRIMINATION
– MAIN BOARD (Conductor Side) –
Type A: PTP008401
Type B: PTP008402
9-874-258-81
XR-CA360/CA360X
1 DIAGRAMS
1-1.
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
z
•
: Through hole.
•
: Pattern from the side which enables seeing.
: Carbon pattern.
•
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Abbreviation
EA
: Saudi Arabia model
• When replacing the IC1, refer to servicing note (Page 2 “When
replacing the IC1”).
2
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• C : panel designation.
• A : B+ Line.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from ACC and BATT cords.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
〈〈
〉〉 : TAPE PLAYBACK
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
f : AM
E : TAPE PLAYBACK
L : BUS AUDIO IN
• Abbreviation
EA
: Saudi Arabia model
• When replacing the IC1, refer to servicing note (Page 2
“When replacing the IC1”).
XR-CA360/CA360X
1-2.
PRINTED WIRING BOARD – MAIN Board –
1
2
Note: When replacing the IC1, refer to servicing note (Page 2 “When replacing the IC1”).
3
4
A
5
6
7
8
9
10
11
6
CN400
BUS
AUDIO IN
ANT100
(FM/AM ANTENNA)
L
R
R
CN800
(BUS CONTROL IN)
(FOR SONY BUS)
7
3
L
2
1
F901
TO
CN700
(FRONT VIEW)
MAIN BOARD
C508
JW8
R417
25
JW5
TH800
JW181
JW113
BCE
D805
Q800
R811
IC2
L1
BCE
C733
ECB
D731
R730
C730
Q731
R732
R352
Q730
X2
B
JW84
R60
C2
C734
Q732
R59
C732
R3
R731
C731
R4
R5
JC147
R722
JW98
R6
R657
50kHz 9kHz
R656
R607
JC170
BRN
1
R712
JW176
D651
S1
RESET
S901
(DIRECTION)
REV
m
FWD
BLU
JW88
R711
S902
(FF/REW)
(OFF : PLAYBACK)
ORG
BRN
RED
(CHASSIS)
1
JW86
R36
R350
R353
Q651
S903
(TAPE DETECT)
(ON : TAPE IN)
YEL
ORG
TO
CN350
Q710
R713
Q711
SW1
FREQUENCY
SELECT
FM
AM
200kHz 10kHz
3
Q350
C710
R655
CONTROL BOARD
CN900
E
8
Q351
JW112
8
YEL
JW85
JW82
JW102
C
CN350
JC166
BCE
JW80
JW128
C3
-2
11
3
BATT
R800
ECB
R740
JW138
JW139
JW29
R654
C601
R852
JW137
R26
R50
JW172
BCE
R58
JW159
R710
GND
4 3
1 2
R81
JW144
JW114
(E)
-1
JW161
JW162
JW163
JC30
R815
C7
JW145
CN600
A
8
D350
12
1
7
JW149
JW150
C600
R600
R601
R602
R603
R604
R605
R606
JW146
R7
C4
JW157
JW171
2
JW60
JW59
R720
R44
R16
R17
C1
R1
C6
R42
JW158
JW61
JW62
R53
R27
R19
1
R39
C314
14 C801
R814
JW143
R351
100
ACC
IC800
1
R804
JW103
X1
R40
BLK
• Semiconductor
Location
Ref. No.
Location
D250
D253
D300
D350
D451
D452
D500
D501
D502
D503
D504
D505
D506
D507
D650
D651
D653
D700
D721
D722
D723
D724
D731
D741
D742
D800
D802
D803
D805
D-5
D-5
G-3
H-10
D-6
D-6
C-7
C-7
C-7
C-7
D-7
D-7
C-7
D-7
E-9
J-10
D-9
D-10
D-8
D-9
D-8
D-9
H-11
E-10
D-10
E-10
E-11
E-11
F-11
IC1
IC2
IC300
IC400
IC500
IC800
G-7
G-11
H-3
E-3
B-6
E-11
Q251
Q252
Q253
Q350
Q351
Q400
Q401
Q402
Q403
Q450
Q451
Q650
Q651
Q710
Q711
Q722
Q724
Q725
Q726
Q730
Q731
Q732
Q740
Q741
Q800
E-5
E-5
E-6
I-11
H-10
D-4
D-4
D-3
D-4
D-5
D-6
E-9
I-9
I-11
I-10
D-8
D-7
E-8
E-7
H-11
G-11
G-10
D-10
E-10
F-11
JW140
ECB
R303
R302
JW76
(CHASSIS)
J
BCE
R721
R725
ECB
JW122
JW135
R18
R47
R20
R48
R46
JW121
JW152
JW153
R31 (E)
+
+
I
JW13
JW3
R728
JW96
JW95
R503
R502
JW119
BCE
JW118
JW116
JW115
R33
25
76
8
C81
R38
JW66
C742
D741
JW117
JW68
C315
C740
JW87
R301
C650
26
JW151
R300
R205
+
R12
IC1
R28 (CA360X) 75
R307
R306
C8
R2
C303
R13
R9
16
RED
D803
JW77
R43
7
ANT REM
Q741
JW99
C5
C305
1
C304
C302
R35
R305
14
50
+
H
(EA)
R309
JC148
R308
R311
51
15
BLU
AMP REM
D802
JW142
R37
R8
L700
+
R310
R304
C307
7
IC300
8
1
R25
C741
Q650
R29 (CA360)
R314
+
R10
R30 (EA)
C306
JC169
JW125
R49
R653
R22
R11
R54
JW127
R55
6
FRONT RCH (–)
JW26
JW141
R21
14
BLU/WHT
JW27
D800
R651 D650
BCE
BCE
C262
R262
R259
BCE
R264
JW120
R14
C311
CN300
3
JW94
R452
B CE
R250
JC53
JW124
JC133
R56
FRONT RCH (+)
D700
Q740
D653
D724
R652
Q725
R41
D300
+
HP901
PLAYBACK
HEAD
C310
R57
R23
ECB
JW89
JC132
JW108
JW55
JW58
JW57
JW56
C400
C401
R312
JC52
C312
JW42
R500
C505
JW123
JW126
G
D722
Q726
REAR RCH (–)
JW28
D742
+
R313
Q253
JW105
R263
JW48
JW90
JW177
R102
17
JC110
B CE
JW54
C100
R423
R401
E
R650
JW97
R505
5
JW17
Q722
D721
13
YEL
TH700
D723
Q724
4
+
F
C
JW47
JW18
JW92
R663
C414
C415
R422
+
+
C413
R418
R106
JW46
C412
R419
R105
JC49
+
12
Q252
B
C411
R420
11
D452
+
R421
C451
Q251
JC104
JW45
C104
D451
C251
JC44
C105
R450
REAR RCH (+)
GRY
GRY/BLK
R801
JW19
JW24
Q451
C452
JW100
12
C800
C701
D507
R451
R400
R101
E
Q450
JW129
JC83
22
4
REAR LCH (–)
JW20
TH701
+
1
7
R802
JW23
D250
5
3
FRONT LCH (–)
REAR LCH (+)
VIO
VIO/BLK
C700
R501
JW180
+
+
6
R664
D504
D253
C410
IC400
C409
C404
8
D505
Q403
JC91
+
D503
1
D501 D502
+
+
JW51
16
D500
C500
R413
C419
+
9
D506
R405
R403
C417
C416
Q401
8
CN700
C503
Q400 JW35
R402
+
JW33
JW31
ECB
JW34
R409
19
1
JW7
R411
C250
C405
R407
B CE
C418
+
C106
R406
R408
R404
1
C423
JW50
D
C427
C421
C420
Q402
TU100
TUNER UNIT
C425
C424
C422
JW32
R410
C522
C521
R412
C426
18
JW22
JW6
C520
C
17
11
CN800
3 2 1
C523
JW4
C429
IC500
FRONT LCH (+)
GRN
GRN/BLK
2
R24
C428
C431
C430
JW9
R415
JW15
R414
2
JW10
24
WHT
WHT/BLK
+
R416
1
10
C403
C402
9
C507
JW2
JW36
JC173
JW11
JW16
JW12
R853
B
13
4
5
8
AUDIO
OUT
12
1-686-927-
11
M
M901
(CAPSTAN/REEL)
XR-CA360/CA360X
SCHEMATIC DIAGRAM – MAIN Board (1/2) –
Note: When replacing the IC1, refer to servicing note (Page 2 “When replacing the IC1”).
E2P SDA
E2P SCL
E2P VDD
TU SCL
TU SDA
GND2
TU VDD
VCC
RDS
MUTE CON
TU MUTE
QUALITY
TU100
TUX-030
TUNER UNIT
S METER
L
R
GND1
(1/2)
ANT
A1
A2
A3
A4
ANT100
(FM/AM ANTENNA)
R101
22k
C104
0.1
C105
0.1
C106
100
10V
R102
3.3
TU4
TU5
R106
220
TU8
TU10
(CHASSIS)
TU9
TU1
R105
220
TU7
C100
0.047
Q251
2SD1664
R263
10
Q252
2PB710A
R259
10k
R250
470
+5V REGULATOR
R262
1k
B2
B1
Q252,253
R264
1k
D253
1SS133
TUNER
B+ SWITCH
C251
10
16V
C250
0.01
D250
MTZJ5.1A
L1
Q253
PDTC114EK
C262
1
A5
A6
R306
56
R312
1k
CN300
3P
R302
100
L-CH
L
R-CH
1/2VCC
C302
0.001
R300
47k
C304
100p
R304
100
D300
1SS133
R314
10
R25
100
C303
0.001
BUS6
AU1
TU10
AU2
R26 100
R53 100
AU3
R16 100k
AU4
R27 100
R18 100 BUS4
R44 100
DAVN
BU-IN
NC
NIL
NCI
TU-ATTIN
RESET
NC
BEEP
POWER-ON
ILL-IN
ACC-IN
NC
TEL-ATT
NCI
BUS-SO
BUS-SI
NC
NC
TU-ATT
NC
NC
NC
NC
LCD-CKO
LO/
R10
100
XI
C3 18p
LCD-CE
PNL2
SYSTEM CONTROLLER
OSC1
IC1
MN101C49HEA
OSC2
FLASH-W
FWD
GND
S902
FF/REW
(FF/REW)
TAPE1
R14
100k
TAPE2
R54
100
GND
R303
100
(OFF:PLAYBACK)
TAPE-IN
S903
TAPE3
C305
100p
R305
100
R309
330k
R313
1k
R60
100
VSS
LCD-RES
VDD
R1 R2
1k 0
NC
NC
NC
MPTH
NC
QUALITY
NC
NC
NC
NC
NC
NC
R8
100
NC
R42
0
C6
22
10V
DAVDD
TAPE-IN
FF/REW
PNL7
N/ R
R606 1k
TAPE-ON
PNL6
DAVSS
R605 1k
NOSE-SW
PNL5
NS-MASK
R604 1k
NC
PNL4
NC
R603 1k
R58
1k
TU1
VREF(EA)
R64
0
C5
0.1
Q350
2SA1428
R353
1
FRASH WRITE
A11
VSM
NC
PNL3
COL-SEL
NC
R602 1k
R9
100
ILL-ON
PNL2
NC
PNL1
R601 1k
NC
R600 1k
NC
CN600
12P
NOSE-SW
NC
EE-CKO
NC
(CHASSIS)
C1
12p
NC
EE-SIO
TU5
NC
TU4
NC
R311
15k
NC
C307
0.01
DEST-SEL2
R307
56
DEST-SEL1
C314
100 6.3V
A10
R41
0
D1
C310
1
50V
R3
100k
VREF+
DEST-SEL0
(ON:TAPE IN)
C2
12p
PNL5
X1
18.432MHz
GND
(TAPE DETECT)
PNL7
R4
4.7k
XO
TEST-IN
N/R
R5
100
MMOD
AM-ON
R11
100
PNL6
IC300
HA12232FP-EL
MOTOR-
A9
R59
1k
X2 32.768KHz
TAPE EQUALIZER
RIP
NC1
PNL4
R6
100
LCD-SO(TX)
NC
VCC
NC3
CN350
8P
NC4
R7
1k
LCD-SI(RX)
DX
FM-ON
MOTOR+
REV
BUS1
NC
R37 100k
NC2
(CAPSTAN/REEL)
BUS-ON
VOL-ATT
R301
47k
M901
S901
BUS2
SYS-RES
TU-ON
PNL3
(DIRECTION)
A8
KEYACK
R55 100
AU8
R
R205
0
D2
R308
330k
C315
100
6.3V
R49
100
C8
0.001
C4 22p
C312
100
10V
C311
470p
NC
TU9
(PLAYBACK)
R310
15k
TUI11
C306
0.01
BUS-CKO
NC
HP901
R13
100
R12
100k
I2C-SIO
R48 100
I2C-CKO
AU7
AMP-ON
R47 100
ATT
AU6
R43 R50
0 100
R21
100
AMP-ATT
R46 100
R17 47k
R22
100
AU5
R19 100 BUS5
R57 0
R23 10k
R24
10k
R56
0
R20 100 BUS3
TU7
TU8
TU11
VREF GND
(E)
LAMP+B
SW1
LAMP+B
(EA)
R35 100k
LCD-DO
R33 100k
MOTOR DRIVE
R352
1.5k
(E)
R31 100k
LCD-CE
R351
1.5k
R30 0
CAPSTAN/REEL
R28 0
(EA)
Q350,351
LCD-DI
A12
SELECT
R350
10k
(CA360X)
LCD-CLK
FREQUENCY
C600
0.1
(CA360)
LCD-RESET
R29 100k
FM
AM
200k
10k
50k
9k
A13
A14
A15
-1
-2
R39
100k
(E)
C11
100p
D350
11ES2
R36
100k
(CHASSIS)
S1
RESET
PNL1
R607
1k
(CHASSIS)
4
4
TAPE2
GND
TAPE4
TAPE3
Q351
PDTC114EK
GND
TAPE1
DRIVE+5V
TAPE4
1-3.
R40
100k
R38
100k
A16
XR-CA360/CA360X
SCHEMATIC DIAGRAM – MAIN Board (2/2) –
(2/2)
CN400
BUS AUDIO IN
R
AUDIO OUT
L
R
L
R853
0
(CHASSIS)
A1
A2
A3
(CHASSIS)
A4
IC500
TA8272H
POWER AMP
GND
R416
10k
R414
1k
C428
100p
R417
10k
R415
1k
C429
100p
C431
3300p
C430
3300p
D502
11ES2
SP2
D501
11ES2
FL+
C424
0.47
C417
4.7
50V
OR2
R410
10k
C522
47p
C500
10
16V
SP3
GND
R406
47k
R407
47k
D500
11ES2
SP4
RIPPLE
RL+
R402
100
FL IN
Q400
DTC314TK
RL IN
CN700
16P
C520
47p
FR IN
MUTING
AU1
C521
47p
Q401
DTC314TK
R500
47k
R505
0
C503
0.001
RR IN
SP5
RR+
MUTING
C421
0.47
R403
100
C425
0.47
R501
2.2k
R411
10k
GND
D507
11ES2
C508
0.1
SP6
VCC1
OF1
R423 0
C412
10p
R408
47k
C413
10p
R409
47k
C419
4.7
50V
OR1
FL-
FRONT LCH+
SP4
RL+
FRONT LCH-
SP3
RL-
REAR LCH+
SP5
RR+
REAR LCH-
SP6
RR-
REAR RCH+
SP7
FR+
REAR RCH-
FR-
FRONT RCH+
AMP-REM
C523
47p
FRONT RCH-
AU6
SP8
SP7
FR+
MUTE
C505
10
16V
D505
11ES2
SP8
ATT-REM
GND
D504
11ES2
FR-
R502
10k
AMP REM
ACC
TEST
R664
1k
Q403
DTC314TK
C423
0.47
R413
10k
C700
3300
16V
C701
0.22
D700
IN5404TU
BATT
BATT
GND
F901
10A
32V
TU7
C427
0.47
ANT REM
GND
ACC
L700
250µH
MUTING
R405
100
AU2
AU4
R412
10k
MUTING
AU3
(EA)
TU8
AU8
R401
39k
SP1
AU7
C456
0.01
C426
0.47
Q402
DTC314TK
C411
0.01
R400
10
C422
0.47
R404
100
OF1
R422 0
R421 100
R420 100
R419 100
OR1
OR2
C410
47
16V
OF2
R418
100
D506
11ES2
RRC418
4.7
50V
FL+
BEEP
A5
A6
SP2
GND
AGND
C415
10p
DGND
12C_DATA
FIL
AN
AP1
MUTE
12C_CLK
AP2
SEL
B2
B1
ADJ
C1
OUT_F1
VCC
C2
OUT_R1
D2
D1
OUT_F2
OUT_R2
IC400
BD3803F-FE2
SP1
VCC2
C420
0.47
C414
10p
VOLUME
D503
11ES2
FLSTBY
RL-
C416
4.7
50V
ELECTRICAL
R503
1k
C507
0.1
OF2
INPUT SELECT,
AU5
D653
MTZJ6.2B
B1
C405 0.47
C403 0.47
B2
C404 0.47
C409 10 16V
D1
C401 0.47
C402 0.47
D2
C400 0.47
GND
A8
TU11
R657
100
Q730
2SD1760
R654
100k
Q722
2SA1428
+9V REGULATOR
R852
0
A9
Q651
2PB709A
ACCESSORY
R656
27k
R655
47k
C601
0.1
R653
4.7k
CHECK
C650
1
50V
R651
47k
D451
1SS133
R450
47
TH700
Q731
2PB709A
R650
4.7k
D650
MTZJ18B
Q650
2PD601A
B+ SWITCH
D651
1SS133
Q450
PDTA114EK
R652
47k
Q724
2SA1428
R732
470
TH701
R720
10k
R730
10k
D721
11ES2
D723
11ES2
Q450,451
A10
MUTING
R81
100k
Q731,732
IC2
PST3443UL
R451
10k
C733
470p
NC
GENERATOR
REGULATOR
C452
1
VDD
SWITCH
RESET SIGNAL
C7
0.047F
5.5V
R452
4.7k
CONTROL
VSS VOUT
1-4.
C81
0.1
Q451
PDTC144EK
R663
100k
D452
MTZJ7.5C
C732
1
C451
47
16V
C730
10
16V
CONTROL
R721
560
1/2W
Q722,724-726
R731
2.2k
B+ SWITCH
R728
10k
R725
560
1/2W
SWITCH
D731
MTZJ9.1C
C734
1
R722
0
Q732
PDTC114EK
Q726
PDTC114EK
D724
11ES2
D722
11ES2
Q725
PDTC114EK
C731
0.047
A11
CN800
8P
BUS CONTROL IN
(FOR SONY BUS)
R710
4.7
1/2W
Q710
2SA1428
GND
R713
10k
BUS5
R814
220k
B+ SWITCH
R712
1.5k
BUS6
R711
1.5k
R815
0
Q740
2SA1428
A12
DATA
OUT
DATA
IN
BUS4
Q710,711
D742
1SS133
BUS-CLK
VREF
CLK
CLK-IN
BUS2
BUS-DATA
I/O
B/U-C
BUS3
BUS-ON
GND
DATA
D800
MTZJ6.8B
BATT
BUS-IN
BUS1
TH800
RESET
R801 100
RST
RST
Q711
PDTC114EK
+B.U
R800 10k
R802 100
BUS-ON
VCC
A13
Q741
2PD601A
A14
Q740,741
R804
10
R740
22k
IC800
MM1175XFF
+5V REGULATOR
A15
Q800
PDTC114EK
BATTERY
C710
0.1
C742
100
10V
C740
10
16V
D741
HZS6B1L
C741
0.01
DETECT
D805
R811
MTZJ18B 1k
SONY BUS
C801
0.01
INTERFACE
D802
MTZJ18B
D803
MTZJ18B
C800
330
16V
(CHASSIS)
A16
(CHASSIS)
5
5
XR-CA360/CA360X
MEMO
6
6
XR-CA360/CA360X
MAIN
2 ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Abbreviation
EA : Saudi Arabia model
Ref. No.
*
Part No.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
Description
Remark
Ref. No.
When indicating parts by reference
number, please include the board.
Part No.
Description
Remark
A-3274-648-A MAIN BOARD, COMPLETE (CA360X)
A-3274-708-A MAIN BOARD, COMPLETE (CA360: E)
A-3274-711-A MAIN BOARD, COMPLETE (EA)
*********************
C402
C403
C404
C405
1-125-891-11
1-125-891-11
1-125-891-11
1-125-891-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47uF
0.47uF
0.47uF
0.47uF
10%
10%
10%
10%
10V
10V
10V
10V
3-041-578-01 BRACKET (IC)
7-685-794-09 SCREW +PTT 2.6X10 (S)
C409
C410
C411
C412
C413
1-126-157-11
1-124-589-11
1-162-970-11
1-162-915-11
1-162-915-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
47uF
0.01uF
10PF
10PF
20%
20%
10%
0.5PF
0.5PF
16V
16V
25V
50V
50V
C414
C415
C416
C417
C418
1-162-915-11
1-162-915-11
1-126-163-11
1-126-163-11
1-126-163-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
10PF
10PF
4.7uF
4.7uF
4.7uF
0.5PF
0.5PF
20%
20%
20%
50V
50V
50V
50V
50V
C419
C420
C421
C422
C423
1-126-163-11
1-125-891-11
1-125-891-11
1-125-891-11
1-125-891-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4.7uF
0.47uF
0.47uF
0.47uF
0.47uF
20%
10%
10%
10%
10%
50V
10V
10V
10V
10V
C424
C425
C426
C427
C428
1-125-891-11
1-125-891-11
1-125-891-11
1-125-891-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47uF
0.47uF
0.47uF
0.47uF
100PF
10%
10%
10%
10%
5%
10V
10V
10V
10V
50V
C429
C430
C431
C451
C452
1-162-927-11
1-162-967-11
1-162-967-11
1-124-589-11
1-109-982-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
100PF
0.0033uF
0.0033uF
47uF
1uF
5%
10%
10%
20%
10%
50V
50V
50V
16V
10V
C456
1-162-970-11 CERAMIC CHIP
0.01uF
10%
25V
C500
C503
C505
C507
1-126-157-11
1-162-964-11
1-126-157-11
1-107-826-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
10uF
0.001uF
10uF
0.1uF
20%
10%
20%
10%
16V
50V
16V
16V
C508
C520
C521
C522
C523
1-107-826-11
1-162-923-11
1-162-923-11
1-162-923-11
1-162-923-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
47PF
47PF
47PF
47PF
10%
5%
5%
5%
5%
16V
50V
50V
50V
50V
C600
C601
C650
C700
1-164-156-11
1-107-826-11
1-104-942-11
1-126-936-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.1uF
0.1uF
1uF
3300uF
10%
20%
20%
25V
16V
50V
16V
< JACK >
ANT100 1-815-185-13 JACK (ANT) (FM/AM ANTENNA)
< CAPACITOR >
C1
C2
C3
C4
C5
1-162-916-11
1-162-916-11
1-162-918-11
1-162-919-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
12PF
12PF
18PF
22PF
0.1uF
5%
5%
5%
5%
10%
50V
50V
50V
50V
16V
C6
C7
C8
C11
C81
1-124-234-00
1-125-701-11
1-162-964-11
1-162-927-11
1-107-826-11
ELECT
DOUBLE LAYER
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.047F
0.001uF
100PF
0.1uF
20%
10%
5%
10%
10V
5.5V
50V
50V
16V
C100
C101
1-165-176-11 CERAMIC CHIP
1-162-964-11 CERAMIC CHIP
0.047uF
0.001uF
10%
10%
16V
50V
C104
C105
C106
1-164-156-11 CERAMIC CHIP
1-164-156-11 CERAMIC CHIP
1-124-584-00 ELECT
0.1uF
0.1uF
100uF
20%
25V
25V
10V
C250
C251
C262
C302
C303
1-162-970-11
1-126-157-11
1-165-908-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10uF
1uF
0.001uF
0.001uF
10%
20%
10%
10%
10%
25V
16V
10V
50V
50V
C304
C305
C306
C307
C310
1-162-927-11
1-162-927-11
1-162-970-11
1-162-970-11
1-104-942-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
100PF
100PF
0.01uF
0.01uF
1uF
5%
5%
10%
10%
20%
50V
50V
25V
25V
50V
C311
C312
C314
C315
C400
1-164-315-11
1-124-584-00
1-124-584-00
1-124-584-00
1-125-891-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
470PF
100uF
100uF
100uF
0.47uF
5%
20%
20%
20%
10%
50V
10V
6.3V
6.3V
10V
C401
1-125-891-11 CERAMIC CHIP
0.47uF
10%
10V
(EA)
(EA)
7
XR-CA360/CA360X
MAIN
Ref. No.
Part No.
Description
Remark
C701
1-165-128-11 CERAMIC CHIP
0.22uF
C710
C730
C731
C732
C733
1-107-826-11
1-126-157-11
1-165-176-11
1-165-908-11
1-164-315-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
0.047uF
1uF
470PF
C734
C740
C741
C742
C800
1-165-908-11
1-126-157-11
1-162-970-11
1-124-584-00
1-126-940-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
C801
1-162-970-11 CERAMIC CHIP
* CN300
* CN350
CN400
CN600
CN700
CN800
1-564-705-11
1-573-486-11
1-774-699-12
1-794-311-21
1-774-701-11
Ref. No.
Part No.
Description
16V
IC500
8-759-827-12 IC TA8272H
10%
20%
10%
10%
5%
16V
16V
16V
10V
50V
IC800
8-759-096-16 IC MM1175XFF
1uF
10uF
0.01uF
100uF
330uF
10%
20%
10%
20%
20%
10V
16V
25V
10V
25V
0.01uF
10%
25V
Remark
< SHORT >
JC30
JC44
JC49
JC52
JC53
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
< CONNECTOR >
JC83
JC91
JC104
JC110
JC132
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
PIN, CONNECTOR (PC BOARD) 3P
PIN, CONNECTOR (PC BOARD) 8P
JACK, PIN 4P (BUS AUDIO IN, AUDIO OUT)
PLUG, CONNECTOR 12P
PIN, CONNECTOR 16P
JC133
JC134
JC147
JC148
JC166
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC169
JC170
JC173
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
0
0
0
1-580-907-31 PLUG, CONNECTOR (BUS CONTROL IN)
< DIODE >
D250
D253
D300
D350
D451
8-719-921-42
8-719-991-33
8-719-991-33
8-719-200-82
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
MTZJ-5.1A
1SS133T-77
1SS133T-77
11ES2
1SS133T-77
D452
D500
D501
D502
D503
8-719-110-03
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
RD7.5ESB2
11ES2
11ES2
11ES2
11ES2
D504
D505
D506
D507
D650
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
8-719-110-49
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
11ES2
11ES2
11ES2
RD18ESB2
D651
D653
D700
D721
D722
8-719-991-33
8-719-109-93
8-719-049-38
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
RD6.2ESB2
1N5404TU
11ES2
11ES2
D723
D724
D731
D741
D742
8-719-200-82
8-719-200-82
8-719-110-14
8-719-935-39
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
11ES2
RD9.1ESB3
HZS6B1LTD
1SS133T-77
D800
D802
D803
D805
8-719-109-97
8-719-110-49
8-719-110-49
8-719-110-49
DIODE
DIODE
DIODE
DIODE
RD6.8ESB2
RD18ESB2
RD18ESB2
RD18ESB2
< COIL >
L1
L700
1-410-509-11 INDUCTOR
1-419-476-11 COIL, CHOKE
10uH
250uH
< TRANSISTOR >
< IC >
IC1
IC2
IC300
IC400
8
6-803-178-01
6-701-405-01
6-802-510-01
6-703-302-02
IC
IC
IC
IC
MN101C49HEA
PST3443UL
HA12232FP-EL
BD3803AF-FE2
Q251
Q252
Q253
Q350
Q351
8-729-920-85
8-729-049-85
8-729-043-27
8-729-205-95
8-729-043-27
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD1664-QR
2PB710AR-115
PDTC114EK-115
2SA1428-Y
PDTC114EK-115
Q400
Q401
Q402
Q403
Q450
8-729-920-21
8-729-920-21
8-729-920-21
8-729-920-21
8-729-043-32
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC314TK-T-146
DTC314TK-T-146
DTC314TK-T-146
DTC314TK-T-146
PDTA114EK-115
Q451
Q650
Q651
Q710
Q711
8-729-043-29
8-729-422-33
8-729-216-22
8-729-205-95
8-729-043-27
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
PDTC144EK-115
2SD601A-Q-TX
2SA1162-G
2SA1428-Y
PDTC114EK-115
Q722
Q724
Q725
Q726
Q730
8-729-205-95
8-729-205-95
8-729-043-27
8-729-043-27
8-729-921-48
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1428-Y
2SA1428-Y
PDTC114EK-115
PDTC114EK-115
2SD1760F5-Q
Q731
Q732
Q740
Q741
Q800
8-729-216-22
8-729-043-27
8-729-205-95
8-729-422-33
8-729-043-27
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1162-G
PDTC114EK-115
2SA1428-Y
2SD601A-Q-TX
PDTC114EK-115
< RESISTOR >
R1
R2
1-216-821-11 METAL CHIP
1-216-864-11 SHORT CHIP
1K
0
5%
1/10W
When replacing the IC1, refer to servicing note
(Page 2 “When replacing the IC1”).
XR-CA360/CA360X
MAIN
Ref. No.
Part No.
Description
Remark
R3
R4
R5
1-216-845-11 METAL CHIP
1-216-829-11 METAL CHIP
1-216-809-11 METAL CHIP
100K
4.7K
100
5%
5%
5%
1/10W
1/10W
1/10W
R6
R7
R8
R9
R10
1-216-809-11
1-249-417-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
100
1K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
1/10W
R11
R12
R13
R14
R16
1-216-809-11
1-249-441-11
1-216-809-11
1-216-845-11
1-216-845-11
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
100
100K
100
100K
100K
5%
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
1/10W
R17
R18
R19
R20
R21
1-216-841-11
1-216-809-11
1-247-807-31
1-247-807-31
1-216-809-11
METAL CHIP
METAL CHIP
CARBON
CARBON
METAL CHIP
47K
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/4W
1/10W
R22
R23
R24
R25
R26
1-216-809-11
1-216-833-11
1-216-833-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
10K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R27
R28
R29
1-247-807-31 CARBON
1-216-864-11 SHORT CHIP
1-216-845-11 METAL CHIP
100
5%
0 (CA360X)
100K
5%
R30
R31
1-216-864-11 SHORT CHIP
1-216-845-11 METAL CHIP
0 (EA)
100K
5%
1/10W
(E)
R33
R35
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
100K
100K
5%
5%
R36
1-216-845-11 METAL CHIP
100K
5%
R37
R38
1-216-845-11 METAL CHIP
1-249-441-11 CARBON
100K
100K
5%
5%
1/10W
1/10W
(EA)
1/10W
(E)
1/10W
1/4W
R39
R40
R41
R42
R43
1-249-441-11
1-249-441-11
1-216-864-11
1-216-864-11
1-216-864-11
CARBON
CARBON
SHORT CHIP
SHORT CHIP
SHORT CHIP
100K
100K
0
0
0
5%
5%
1/4W
1/4W
R44
R46
R47
R48
R49
1-247-807-31
1-247-807-31
1-216-809-11
1-247-807-31
1-216-809-11
CARBON
CARBON
METAL CHIP
CARBON
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/10W
1/4W
1/10W
R50
R53
R54
R55
R56
1-247-807-31
1-247-807-31
1-216-809-11
1-216-809-11
1-216-864-11
CARBON
CARBON
METAL CHIP
METAL CHIP
SHORT CHIP
100
100
100
100
0
5%
5%
5%
5%
1/4W
1/4W
1/10W
1/10W
R57
R58
R59
R60
R64
1-216-864-11
1-249-417-11
1-249-417-11
1-216-809-11
1-216-809-11
SHORT CHIP
CARBON
CARBON
METAL CHIP
METAL CHIP
0
1K
1K
100
100
5%
5%
5%
5%
1/4W
1/10W
(CA360)
1/4W
1/4W
1/10W
1/10W
(EA)
Ref. No.
Part No.
Description
R81
R101
R102
R105
R106
1-216-845-11
1-216-837-11
1-249-387-11
1-216-813-11
1-216-813-11
METAL CHIP
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
100K
22K
3.3
220
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/10W
1/10W
Remark
R205
R250
R259
R262
R263
1-216-864-11
1-216-817-11
1-216-833-11
1-216-821-11
1-216-797-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
470
10K
1K
10
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R264
R300
R301
R302
R303
1-216-821-11
1-216-841-11
1-216-841-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
47K
47K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R304
R305
R306
R307
R308
1-216-809-11
1-216-809-11
1-216-806-11
1-216-806-11
1-216-851-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
56
56
330K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R309
R310
R311
R312
R313
1-216-851-11
1-216-835-11
1-216-835-11
1-249-417-11
1-249-417-11
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
CARBON
330K
15K
15K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
1/4W
R314
R350
R351
R352
R353
1-216-797-11
1-216-833-11
1-249-419-11
1-249-419-11
1-217-671-11
METAL CHIP
METAL CHIP
CARBON
CARBON
RES-CHIP
10
10K
1.5K
1.5K
1
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/4W
1/10W
R400
R401
R402
R403
R404
1-216-797-11
1-216-840-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
39K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R405
R406
R407
R408
R409
1-216-809-11
1-216-841-11
1-216-841-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
47K
47K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R410
R411
R412
R413
R414
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R415
R416
R417
R418
R419
1-216-821-11
1-216-833-11
1-216-833-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
10K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R420
R421
R422
R423
R450
1-216-809-11
1-216-809-11
1-216-864-11
1-216-864-11
1-216-805-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
100
100
0
0
47
5%
5%
1/10W
1/10W
5%
1/10W
R451
R452
R500
1-216-833-11 METAL CHIP
1-216-829-11 METAL CHIP
1-216-841-11 METAL CHIP
10K
4.7K
47K
5%
5%
5%
1/10W
1/10W
1/10W
9
XR-CA360/CA360X
MAIN
Ref. No.
Part No.
Description
Remark
R501
R502
1-216-825-11 METAL CHIP
1-216-833-11 METAL CHIP
2.2K
10K
5%
5%
1/10W
1/10W
R503
R505
R600
R601
R602
1-216-821-11
1-216-864-11
1-249-417-11
1-249-417-11
1-249-417-11
METAL CHIP
SHORT CHIP
CARBON
CARBON
CARBON
1K
0
1K
1K
1K
5%
1/10W
5%
5%
5%
1/4W
1/4W
1/4W
R603
R604
R605
R606
R607
1-249-417-11
1-249-417-11
1-249-417-11
1-249-417-11
1-216-821-11
CARBON
CARBON
CARBON
CARBON
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/10W
R650
R651
R652
R653
R654
1-249-425-11
1-216-841-11
1-216-841-11
1-216-829-11
1-216-845-11
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47K
47K
4.7K
100K
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/10W
1/10W
R655
R656
R657
R663
R664
1-216-841-11
1-216-838-11
1-216-809-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
27K
100
100K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R710
R711
R712
R713
R720
1-260-300-11
1-249-419-11
1-249-419-11
1-216-833-11
1-216-833-11
CARBON
CARBON
CARBON
METAL CHIP
METAL CHIP
4.7
1.5K
1.5K
10K
10K
5%
5%
5%
5%
5%
1/2W
1/4W
1/4W
1/10W
1/10W
R721
R722
R725
R728
R730
1-247-749-11
1-216-864-11
1-247-749-11
1-216-833-11
1-216-833-11
CARBON
SHORT CHIP
CARBON
METAL CHIP
METAL CHIP
560
0
560
10K
10K
5%
1/2W
5%
5%
5%
1/2W
1/10W
1/10W
R731
R732
R740
R800
R801
1-249-421-11
1-216-817-11
1-216-837-11
1-216-833-11
1-216-809-11
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
470
22K
10K
100
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/10W
1/10W
R802
R804
R811
R814
R815
1-216-809-11
1-216-797-11
1-249-417-11
1-216-849-11
1-216-864-11
METAL CHIP
METAL CHIP
CARBON
METAL CHIP
SHORT CHIP
100
10
1K
220K
0
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/10W
R852
R853
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
0
0
< SWITCH >
S1
SW1
1-692-431-21 SWITCH, TACTILE (RESET)
1-572-552-11 SWITCH, SLIDE (FREQUENCY SELECT) (E)
< TUNER UNIT >
TU100
A-3220-944-A TUNER UNIT TUX-031
< THERMISTOR >
TH700
TH701
TH800
10
1-801-726-11 THERMISTOR, POSITIVE
1-801-726-11 THERMISTOR, POSITIVE
1-801-792-21 THERMISTOR, POSITIVE
Ref. No.
Part No.
Description
Remark
< VIBRATOR >
X1
1-795-539-11 VIBRATOR, CRYSTAL (18.432MHz)
X2
1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
************************************************************
XR-CA360/CA360X
MEMO
11
XR-CA360/CA360X
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
1.0
1.1
Date
2002.12
2003.02
Description of Revision
New
Addition of JIG
Correction of Part No. for Ref. No. 57, 58, LCD1
XR-CA360X Saudi Arabia model is deleted
(ECN-CSA06620/CSA06687/ENG-03001/SPM-03004)
1.2
2003.12
Addition of “When replaceing the IC1” to SERVICING NOTE
Change of Part No. for Ref. No. IC1, TU100
Change of Part No. for mechanism deck (MG-36SZ13-32)
Change of MAIN board (SUPPLEMENT-1: 9-874-258-81)
(ECN-CSA07071/CSA07525/CSA07576/CSB04022)