Download SERVICE MANUAL

CFD-S03CP/S03CPL
SERVICE MANUAL
Canadian Model
CFD-S03CP
AEP Model
Ver. 1.6 2007.08
CFD-S03CP/S03CPL
UK Model
E Model
Australian Model
CFD-S03CP
Photo: CFD-S03CP
Model Name Using Similar Mechanism CFD-S01
CD
CD Mechanism Type
KSM-213CDP
Section
Optical Pick-up Name
KSS-213C
Model Name Using Similar Mechanism CFD-S01
TC
Section Tape Transport Mechanism Type
MF-S01
SPECIFICATIONS
CD player section
System
Compact disc digital audio system
Laser diode properties
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on the
optical pick-up block with 7 mm aperture.)
Number of channels
2
Frequency response
20 - 20 000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
FM: 87.5 - 108 MHz
CND, E92, MX model:
AM: 530 - 1 710 kHz
TW model:
AM: 531 - 1 611 kHz
EXCEPT CND, E92, MX, TW model:
AM/MW: 531 - 1 611 kHz (9 kHz step)
530 - 1 610 kHz (10 kHz step)
CFD-S03CPL:
LW: 153 - 279 kHz
IF
FM: 10.7 MHz
AM/MW/LW: 450 kHz
Antennas
FM: Telescopic antenna
AM/MW/LW: Built-in ferrite bar antenna
9-887-043-07
2007H04-1
© 2007.08
Sony Corporation
Personal Audio Division
Published by Sony Techno Create Corporation
Cassette-corder section
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 150 s (sec.) with Sony cassette C-60
Frequency response
TYPE I (normal): 80 - 10 000 Hz
General
Speaker
Full range: 8 cm dia., 4 Ω, cone type (2)
Outputs
Headphones jack (stereo minijack):
For 16 - 32 Ω impedance headphones
Power output
1.7 W + 1.7 W (at 4 Ω, 10% harmonic distortion)
Power requirements
For CD radio cassette-corder:
120 V AC, 60 Hz (CND, E92, MX, TW model)
220 V AC, 60 Hz (KR model)
220 – 230 V AC, 50 Hz (AR model)
230 V AC, 50 Hz (EXCEPT E92, KR, MX, AR, TW model)
9 V DC, 6 R14 (size C) batteries
For remote control:
3 V DC, 2 R03 (size AAA) batteries
– Continued on next page –
CD RADIO CASSETTE-CORDER
CFD-S03CP/S03CPL
Ver. 1.2
Power consumption
AC 13 W (CND, E92, MX model)
AC 12 W (EXCEPT CND, E92, MX model)
Battery life
For CD radio cassette-corder:
FM recording
Sony R14P: approx. 6 h
Sony alkaline LR14: approx. 20 h
Tape playback
Sony R14P: approx. 3 h
Sony alkaline LR14: approx. 12 h
CD playback
Sony R14P: approx. 1.5 h
Sony alkaline LR14: approx. 4.5 h
Dimensions
Approx. 360 × 141 × 235 mm (w/h/d)
(incl. projecting parts)
Mass
Approx. 2.6 kg (incl. batteries)
Supplied accessory
AC power cord (1)
Remote control (1)
Design and specifications are subject to change
without notice.
• Abbreviation
CND : Canadian model
E92 : AC 120V area in E model
KR : Korea model
MX : Mexican model
AR : Argentina model
TW : Taiwan model
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged
by heat.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Notes on DualDiscs
A DualDisc is a two sided disc product which mates DVD recorded
material on one side with digital audio material on the other side.
However, since the audio material side does not conform to the
Compact Disc (CD) standard, playback on this product is not
guaranteed.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
CFD-S03CP/S03CPL
SOLDER
• UNLEADED
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
TABLE OF CONTENTS
1.
SERVICING NOTES ................................................ 4
2.
GENERAL ................................................................... 5
3.
DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
3-10.
3-11.
3-12.
Cabinet (Rear) Assy .........................................................
Cabinet (Front) Assy, Cabinet (Upper) Assy ...................
Main Board ......................................................................
CD Block Assy ................................................................
BD83S Board ..................................................................
Optical Pick-up ................................................................
Panel Board .....................................................................
CD Lid .............................................................................
Tape Mechanism Block, Belt (1), Belt (2) ......................
TC Board .........................................................................
Key-1 Board, Key-2 Board ..............................................
Power Board ....................................................................
4.
MECHANICAL ADJUSTMENTS ......................... 13
5.
ELECTRICAL ADJUSTMENTS
7
7
8
8
9
9
10
10
11
11
12
12
Tape Section .................................................................... 13
Tuner Section ................................................................... 14
CD Section ...................................................................... 16
6.
DIAGRAMS
6-1.
6-2.
6-3.
6-4.
6-5.
6-6.
6-7.
6-8.
6-9.
6-10.
6-11.
6-12.
6-13.
6-14.
6-15.
Block Diagram – CD Section – .......................................
Block Diagram – Main Section – ....................................
Circuit Boards Location ..................................................
Printed Wiring Board – BD83S Section – .......................
Schematic Diagram – BD83S Section – ..........................
Printed Wiring Board – Main Section – ..........................
Schematic Diagram – Main Section (1/3) – ....................
Schematic Diagram – Main Section (2/3) – ....................
Schematic Diagram – Main Section (3/3) – ....................
Printed Wiring Boards – TC Section – ............................
Schematic Diagram – TC Section – ................................
Printed Wiring Boards – Panel Section – ........................
Schematic Diagram – Panel Section – ............................
Printed Wiring Boards – Power Supply Section – ...........
Schematic Diagram – Power Supply Section – ...............
7.
EXPLODED VIEWS
7-1.
7-2.
7-3.
7-4.
7-5.
7-6.
Rear Cabinet Section .......................................................
Front Cabinet Section (1) ................................................
Front Cabinet Section (2) ................................................
Upper Cabinet Section (1) ...............................................
Upper Cabinet Section (2) ...............................................
CD Mechanism Section ...................................................
8.
ELECTRICAL PARTS LIST .................................. 45
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
39
40
41
42
43
44
3
CFD-S03CP/S03CPL
Ver. 1.4
SECTION 1
SERVICING NOTES
CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the lid (CD), use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
1. Turn ON the [OPERATE] button and press [CD] button to CD
position.
2. Open the CD lid.
3. Turn on SW2 with screwdriver, etc. as following figure.
4. Press the N X (CD) button.
5. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Optical Pick-up is broken.
Objective lens moves up and down three times for focus search.
NOTE FOR REPLACEMENT OF THE IC804 AND
IC806
There have been changes to the 3.3V regulator circuit in the course
of production.
When repairing the 3.3V regulator circuit, check which of TYPE A
or B is applicable as specified in the table below.
Ref. No.
IC804
IC806
R883
R884
4
TYPE A
S-816A33AMC-BAI-T2-G
NO MOUNT
100k
220k
TYPE B
NO MOUNT
XC6202P332FR
NO MOUNT
NO MOUNT
SW2
CFD-S03CP/S03CPL
SECTION 2
GENERAL
This section is extracted
from instruction manual.
Basic Operations
To
Pause playback
Press
u 9. To resume play, press it
again.
Stop playback
Go to the next
track/MP3 file
Go back to the
previous track/
MP3 file
Select a folder on
an MP3 disc
Play the selected
folder only (MP3
disc only)
x 9.
If you need to change the AM/MW tuning interval, do
the following:
1 Press RADIO•BAND•AUTO PRESET qd on the
unit until “AM” or “MW” is displayed.
> 7.
2 Press DISPLAY•ENTER 5 on the unit for 2
seconds.
. 7.
3 Press RADIO•BAND•AUTO PRESET qd on the
+ 0 on the unit to go forward
– 0 to go backward.
and
MODE 4 on the unit until
+ or – 0 on
“FLDR” appears,
the unit to select a folder and then
u 9 to start playing.
> (forward) or . (backward)
7 while playing and hold it until
you find the point.
> (forward) or . (backward)
7 in pause and hold it until you
find the point.
Z PUSH OPEN/CLOSE 8 on the
unit.
Locate a point
while listening to
the sound
Locate a point
while observing
the display
Remove the CD
Changing the AM/MW tuning interval
unit for 2 seconds.
“9K STEP” or “10K STEP” flashes.
4 Press PRESET + or – 7 on the unit to select
“9K STEP” for 9 kHz interval or “10K STEP” for
10 kHz interval.
5 Press DISPLAY•ENTER 5 on the unit.
After changing the tuning interval, you need to reset your
preset AM/MW radio stations.
Playing a tape
Use buttons on the unit for the operation.
1 Press TAPE qd on the unit (direct power-on).
2 Press xZ qs on the unit, and insert the tape into
the tape compartment with the side you want to
play facing you. Use TYPE I (normal) tape only.
Close the compartment.
Make sure there is no slack in the tape to avoid
damaging the tape or the unit.
Tips
• Playback starts from the track/MP3 file you last stopped playing
(Resume play). During stop, the track/MP3 file number to be played
is displayed.
• To cancel the resume play (to start play from the beginning of the
first track/MP3 file), press x 9 in stop mode. When you open
the CD compartment or turn off the unit, the resume play is also
canceled.
Example of folder structure and playing
order
The playing order of the folders and files is as follows:
* VOLUME + (VOL + on the remote) qa, u 9 and n qs on the
unit have a tactile dot.
CD-R
CD-RW
Folder
MP3 file
Before using the unit
1
3 Press n qs.
The player starts playing.
1
2
To turn on/off the power
European model: Press OPERATE 1.
Other models: Press POWER 1.
2
3
To adjust the volume
Press VOLUME +, – (VOL +, – on the remote) qa.
3
To listen through headphones
4
5
Connect the headphones to the i (headphones) jack qf.
4
To reinforce the bass sound
Press MEGA BASS 2.
“MEGA BASS” appears in the display.
To return to normal sound, press the button again.
6
To
Press
Pause playback
X qs on the unit. To resume play,
press it again.
xZ qs on the unit.
m or M (fast forward or
rewind) qs on the unit.
xZ qs on the unit.
Stop playback
Fast-forward or
rewind*
Eject the cassette
* When the tape is wound to the end, press xZ qs to release m or
M qs.
7
8
Recording on a tape
Use buttons on the unit for the operation.
5
Playing a CD/MP3 disc
1 Press CD qd on the unit (direct power-on).
(On the remote, press OPERATE or POWER 1 and
then press FUNCTION qh repeatedly until “CD”
appears in the display.)
2 Press Z PUSH OPEN/CLOSE 8 on the unit,
and place a disc with the label side up on the CD
compartment.
To close the CD compartment, press Z PUSH OPEN/
CLOSE 8 on the unit.
3 Press u 9.
The player plays all the tracks/MP3 files once.
When you play a MP3 disc, MP3 indicator lights up
after the player reads the file information.
Audio CD
Track
number
Playing
time
MP3 disc
MP3 file
number
After the folder name*, song title
and artist name are displayed,
the playing time** will appear.
* If there is no folder, “ROOT” appears in the display.
** If the playing time is more than 100 minutes, it appears “--:--” in
the display.
6
9
1 Press xZ qs on the unit to open the tape
compartment and insert a blank tape with the
side you want to record on facing you. Use TYPE
I (normal) tape only. Close the compartment.
0
2 Select the program source you want to record.
Notes on MP3 discs
• When the disc is inserted, the player reads all the files on that disc.
During this time, “READING” is displayed. If there are many
folders or non-MP3 files on the disc, it may take a long time for play
to begin or for the next MP3 file to start play.
We recommend that you do not save unnecessary folders or files
other than MP3 ones in the disc to be used for MP3 listening.
• A folder that does not include an MP3 file is skipped.
• Maximum number of files: 255
Maximum number of folders: 150 (including the root folder)
Maximum number of folders and files in total: 256
Maximum directory levels: 8
• Folder names and file names can be displayed with up to 30
characters including quotation marks.
• The characters A - Z, 0 - 9, and _ can be displayed on this player.
Other characters are displayed as “_”.
• This player conforms to Version 1.0, 1.1, 2.2, 2.3 and 2.4 of the
ID3 tag format. When the file has the ID3 tag information, “song
title”, “artist name” and “album name” can be displayed and
“ID3” appears in the display. If the file does not have the ID3 tag
information, file name appears instead of song title, folder name
appears instead of album name and “no artist” appears instead of
artist name. The ID3 tag information can be displayed with up to 15
characters.
• When naming, be sure to add the file extension “mp3” to the file
name.
• If you put the extension “mp3” to a file other than an MP3 file, the
player cannot recognize the file properly and will generate random
noise that could damage your speakers.
• The file name does not correspond to the ID3 tag.
To record from the CD player, insert a CD and press
CD qd.
To record from the radio, tune in the station you want.
3 Press z qs on the unit to start recording
(n is depressed automatically).
To
Press
Pause recording
X qs on the unit.
Stop recording
xZ qs on the unit.
To resume recording, press it
again.
Tips
• Adjusting the volume or the audio emphasis will not affect the
recording level.
• If the AM/MW/LW program makes a whistling sound after you’ve
press z qs in step 3, press MODE 4 on the unit to select the
position of ISS (Interference Suppress Switch) that most decreases
the noise.
• For the best results, use the AC power as a power source for
recording.
• To erase a recording, proceed as follows:
1 Insert the tape whose recording you want to erase.
2 Press TAPE qd on the unit.
3 Press z qs on the unit.
Listening to the radio
1 Press RADIO•BAND•AUTO PRESET qd on the
unit (BAND qg on the remote) repeatedly (direct
power-on).
Each time you press the button, the indication changes
as follows:
CFD-S03CPL: “FM” t “MW” t “LW”
CFD-S03CP: “FM” t “AM”
2 Hold down TUNE + or – 0 until the frequency
digits begin to change in the display.
The player automatically scans the radio frequencies
and stops when it finds a clear station.
If you can not tune in a station, press TUNE + or – 0
repeatedly to change the frequency step by step.
When an FM stereo broadcast is received, “ST”
appears.
Tip
If the FM broadcast is noisy, press MODE 4 until “MONO” appears
in the display and the radio will play in monaural.
5
CFD-S03CP/S03CPL
SECTION 3
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
SET
3-1.
CABINET (REAR) ASSY
(Page 7)
3-2.
CABINET (FRONT) ASSY,
CABINET (UPPER) ASSY
(Page 7)
3-3.
MAIN BOARD
(Page 8)
3-9.
3-12. POWER BOARD
(Page 12)
TAPE MECHANISM BLOCK,
BELT (1), BELT (2)
(Page 11)
3-11. KEY-1 BOARD,
KEY-2 BOARD
(Page 12)
3-10. TC BOARD
(Page 11)
3-4.
CD BLOCK ASSY
(Page 8)
3-5.
BD83S BOARD
(Page 9)
6
3-7.
PANEL BOARD
(Page 10)
3-6.
OPTICAL PICK-UP
(Page 9)
3-8.
CD LID
(Page 10)
CFD-S03CP/S03CPL
Note: Follow the disassembly procedure in the numerical order given.
3-1. CABINET (REAR) ASSY
2 screw
(+BV tapping B2.6)
1 two screws
(+BV tapping (B2.6))
telescopic antenna
4 three screws
(+BV tapping (B2.6))
handle
3 screw
(+BV tapping B2.6)
5
6 CN305 (3P)
7 cabinet (rear) assy
3-2. CABINET (FRONT) ASSY, CABINET (UPPER) ASSY
2 screw
(+BV tapping B2.6)
9 cabinet (upper) assy
4
1 CN308 (4P)
3 screw
(+BV tapping B2.6)
5 flexible flat cable (4 core)
(CN403)
6 CN304 (4P)
7 flexible flat cable (14 core)
(CN301)
8 cabinet (front) assy
7
CFD-S03CP/S03CPL
3-3. MAIN BOARD
9 flexible flat cable(23 core)
(CN805)
1 CN306 (4P)
4 connector
(S801)
8
3 flexible flat cable(20 core)
(CN803)
0 MAIN board
7 two screws
(+BV tapping B2.6)
5 two screws
(+BV tapping B2.6)
2 flexible flat cable(20 core)
(CN804)
6 screw
(+BV tapping B2.6)
3-4. CD BLOCK ASSY
4 CD cover
claw
two claws
5 CD block assy
3 CD chassis
2 two screws
(+BV tapping (B2.6))
1 two screws
(+BV tapping (B2.6))
8
CFD-S03CP/S03CPL
3-5. BD83S BOARD
4 Remove the two solders.
5 BD83S board
1 flexible flat cable(16 core)
(CN301)
3 Remove the two solders.
2 screw
(+BVTT 2 × 6)
3-6. OPTICAL PICK-UP
5 optical pick-up
1 gear (A)
claw
3
2 claw
4 sled shaft
9
CFD-S03CP/S03CPL
3-7. PANEL BOARD
3 PANEL board
2 five screws
(+P tapping (B2.6))
1 four screws
(+P tapping (B2.6))
3-8. CD LID
5 CD lid
1
2
4
3
6 CD spring
10
CFD-S03CP/S03CPL
3-9. TAPE MECHANISM BLOCK, BELT (1), BELT (2)
6 belt (1)
7 belt (2)
5 motor bracket
1 two screws
(+BV tapping (B2.6))
4 two screws
3 tape mechanism block
2 two screws
(+BV tapping (B2.6))
3-10. TC BOARD
2 Remove the four solders.
1 screw
(+P tapping (B2.6))
3 TC board
11
CFD-S03CP/S03CPL
3-11. KEY-1 BOARD, KEY-2 BOARD
9 button (FUNC)
6 three screws
(+BV tapping (B2.6))
8 KEY-1 board
7 HOLDER board
2 two screws
(+BV tapping (B2.6))
3 two HOLDER boards
5 button (volume)
1 flexible flat cable(4 core)
(CN421)
4 KEY-2 board
3-12. POWER BOARD
3 two screws
(+BV tapping (B2.6))
1 CN902 (2P)
4 POWER board
2 screw
(+BV tapping (B2.6))
12
SECTION 4
MECHANICAL ADJUSTMENTS
PRECAUTION
TAPE SECTION
1. Clean the following parts with a denatured-alcohol-moistened
swab :
record/playback head
pinch roller
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head demagnetizer.
(Do not bring the head magnetizer close to the erase head.)
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the rated power
supply voltage (9V) unless otherwise noted.
Torque Measurement
Mode
Torque meter
Meter reading
FWD
CQ-102C
2.95 – 6.86 mN • m
(30 – 70 g • cm)
(0.42 – 0.97 oz • inch)
FWD
Back Tension
CQ-102C
0.15 – 0.53 mN • m
(1.5 – 5.5 g • cm)
(0.021 – 0.076 oz • inch)
FF
CQ-201B
more than 5.88 mN • m
(more than 60 g • cm)
(more than 0.83 oz • inch)
CQ-201B
more than 5.88 mN • m
(more than 60 g • cm)
(more than 0.83 oz • inch)
REW
Tape Tension Measurement
Mode
Tension meter
FWD
CQ-403A
CFD-S03CP/S03CPL
SECTION 5
ELECTRICAL ADJUSTMENTS
Meter reading
more than 100 g
(more than 3.53 oz)
0 dB = 0.775 V
• Standard Output Level
Output terminal
HP OUT
32 Ω
0.25 V (–10 dB)
load impedance
output signal level
• Test Tape
Type
WS-48A
Signal
Used for
3 kHz, 0 dB
tape speed adjustment
Tape Speed Adjustment
Procedure:
Mode: playback
digital frequency
counter
test tape
WS-48A
(3 kHz, 0 dB)
32 Ω
set
i jack (J321)
Adjust so that the value on the digital frequency counter is
3,000 Hz.
Specification Value:
Digital frequency counter
2,910 to 3,090 Hz
Adjust so that the frequency at the beginning and that at the end of
tape winding are between 2,910 to 3,090 Hz.
Adjustment Location:
Tape speed adjustment
control inside motor
13
CFD-S03CP/S03CPL
Ver. 1.2
TUNER SECTION
0 dB = 1 µV
[AM (MW/LW)]
Setting:
Function: RADIO/BAND/AUTO PRESET
Band: MW or LW
T1
Put the loop
antenna close to
the set.
AM RF signal
generator
level meter
32 Ω
+
–
set
30% amplitude
modulation by
400 Hz signal
Output level:
as low as possible
i jack (J321)
MAIN board
TP ANT2 (JW231, 232) level meter
0.01 µF
32 Ω
+
–
set
75 kHz frequency
deviation by 1 kHz
signal
Output level:
as low as possible
i jack (J321)
• Connecting Digital Voltmeter (FM, MW and LW)
digital voltmeter
MAIN board
TP (VT)
TP (GND)
LW FREQUENCY COVERAGE ADJUSTMENT (AEP)
Adjustment Part Frequency Display Reading on Digital Voltmeter
L3
279 kHz
5.3 ± 0.5 V
Confirmation
153 kHz
0.6 ± 0.05 V
LW TRACKING ADJUSTMENT (AEP)
Adjust for a maximum reading on level meter
ANT1-2
162 kHz
CT5
261 kHz
MW FREQUENCY COVERAGE ADJUSTMENT (AEP)
Adjustment Part Frequency Display Reading on Digital Voltmeter
Confirmation
531 kHz
0.9 ± 0.2 V
Confirmation
1,611 kHz
5.5 ± 0.5 V
[FM]
Setting:
Function: RADIO/BAND/AUTO PRESET
BAND button: FM
FM RF signal
generator
AM (MW/LW) IF ADJUSTMENT
Adjust for a maximum reading on level meter
450 kHz
100 k Ω
• Repeat the procedures in each adjustment several times, and the
tracking adjustments should be finally done by the trimmer
capacitors.
• Remove FM antenna in FM adjustment.
MW FREQUENCY COVERAGE ADJUSTMENT
(EXCEPT CND, AEP, E92, MX)
Adjustment Part Frequency Display Reading on Digital Voltmeter
L3
531 kHz
0.8 ± 0.05 V
Confirmation
1,611 kHz
5.0 ± 0.5 V
MW FREQUENCY COVERAGE ADJUSTMENT (CND, E92, MX)
Adjustment Part Frequency Display Reading on Digital Voltmeter
L3
530 kHz
0.8 ± 0.5 V
Confirmation
1,710 kHz
5.8 ± 0.05 V
MW TRACKING ADJUSTMENT (EXCEPT CND, E92, MX)
Adjust for a maximum reading on level meter
ANT1-1
621 kHz
CT3
1,404 kHz
MW TRACKING ADJUSTMENT (CND, E92, MX)
Adjust for a maximum reading on level meter
ANT1-1
620 kHz
CT3
1,400 kHz
L6
FM IF ADJUSTMENT
Adjust for a minimum reading on level meter
10.7 MHz
FM FREQUENCY COVERAGE ADJUSTMENT
Adjustment Part Frequency Display Reading on Digital Voltmeter
L2
108 MHz
3.0 ± 0.2 V
Confirmation
87.5 MHz
1.5 ± 0.5 V
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter
L1
87.5 MHz
CT1
108 MHz
Adjustment and Connecting Location:
MAIN board (See page 15)
• Abbreviation
CND : Canadian model
E92 : AC 120V area in E model
MX : Mexican model
14
CFD-S03CP/S03CPL
Adjustment Location:
L2: FM FREQUENCY
COVERAGE
ADJUSTMENT
CT1: FM TRACKING
ADJUSTMENT
L3: AM (MW/LW)
FREQUENCY COVERAGE
ADJUSTMENT
– MAIN BOARD (Component Side) –
CT5: LW TRACKING
ADJUSTMENT
IC1
ANT1
ANT1-1: MW TRACKING
ADJUSTMENT
ANT1-2: LW TRACKING
ADJUSTMENT
CT3: MW TRACKING
ADJUSTMENT
L6: FM IF ADJUSTMENT
L1: FM TRACKING
ADJUSTMENT
T1: AM (MW/LW)
IF ADJUSTMENT
Test Point:
– MAIN BOARD (Conductor Side) –
TP ANT2
D5
JW232
D4
JW231
C19
R14
C18
R25
C28
R29
D6
C37
JW187
JW2
C72
T1
L6
C30
R32
R31
C51
Q32
R22
E92,MX
MODEL
C32
R41
C68
TP (VT)
R18
C39
R20
R28
C27
CF2
CF3
C25
R17
C69
JW209
R21
JW188
JW191
R36
CT3
C31
R23
R4
C4
R26
R35
R34
JW220
C54
C29
R30
Q35
C55
C53
CT5
R19
C34
C24
C35
C38
R10
JW219
C40
R16
JW226
C20
C41
C26
JW218
R27
C42
IC1
C22
C9
C70
R37
X1
C23
JW217
R5
R15
C67
JW208
C61
D3
L1
R38
Q33
C64
C3
C62
R6
R12
C33
C1
C60
C21
C11
C10
JW207
C46
C45
D1
C15
C63
C12
R13
C7
R7
JW223
R2
R11 JW224
R3
R1
R9
C16
C5
CT1
C2
C14
C13
C17
L2
C6
R39
D2
L3
TP (GND)
15
CFD-S03CP/S03CPL
CD SECTION
CD section adjustments are done automatically in this set.
In case of operation check, confirm that focus bias.
Test Point:
– BD83S BOARD (Conductor Side) –
C292
B9
R270
C301 C304
C213 C222
C214
R267
100
91
C221
R268
C217
90
1
R278
C261
R258
R250
03
IC201
FEI
C252
C253
1-868-067-
TP (VC)
When observing the eye pattern, set the oscilloscope for AC range
and raise vertical sensitivity.
16
CN301
C256
C254
C251
APC
R254
R252
VC
C208
61
60
C224
R253
R255
30
31
TEI
RF level :
1.1 +0.3
–0.2 Vp-p
R266
C265
C273
C264
C260
RFACI
RFACO
VOLT/DIV : 50 mV (10 : 1 probe in use)
TIME/DIV : 500 nS
C303
R257
03
C258
• RF signal reference waveform (eye pattern)
R265
C291
R292
C218
C230
1. Connect the oscilloscope between IC201 pin u; and pin th (or
TP (RFAC0) and TP (VC)).
2. Insert the disc (PATD-012 (Tr 15)). (Part No. : 4-225-203-01)
3. Press the N X (CD) button.
4. Confirm that the oscilloscope waveform is as shown in the figure
below. (eye pattern)
A good eye pattern means that the diamond shape ( ) in the
center of the waveform can be clearly distinguished.
R291
FOCUS BIAS CHECK
TP (RFAC0)
11
(11)
CFD-S03CP/S03CPL
SECTION 6
DIAGRAMS
6-1. BLOCK DIAGRAM — CD SECTION —
AOUT1
A
57
B
B
C
C
59
D
D
60
E
E
F
F
58
50
51
PD
PD
66
67
SYNCHRONOUS
CIRCUIT
DSP
AOUT2
B
CD_IN_ L
117
CD_IN_R
A
PRISERVO
AMP
D
RF AMP,
SYSTEM SERVO PROCESSOR,
DIGITAL SIGNAL PROCESSOR
IC201
E
F
DIGITAL
SERVO
CONTROL
LD
PD
I/F
APC
VDD (3.3V)
44 43 45 46 41 42 38
TRACKING
COIL
T+
T–
13 CH1OUTR TRACKING
COIL
CH1OUTF
14
DRIVE
CH1INR
5
CH1INF
4
FOCUS
COIL
F+
F–
CH2OUTF
12
CH2OUTR
11
CH2INF
6
CH2INR
7
FOCUS
COIL
DRIVE
39
12 90 13
REQ-MP3
IREQ-MP3
ACK-MP3
XTACN
XLAT
DATA
CLOK
SENS
SCOR
XRST
56 VC
OPTICAL PICK-UP
BLOCK
(KSS-213C)
SSTB
TRDR
TFDR
FFDR
FRDR
SFDR
SRDR
MDP
VC
DATA2
CLK2
XLAT-MP3
CLOCK
GENERATOR
VC
(Page 18)
C
VR
VC
112
DAC
14 10 15 7 16 89 11 20 26 8
VDD (1.8V)
+1.8V REG.
IC202
CD3.3V
XTAO
LD
LD
LD POWER
CONTROLLER
Q321
A
XTAI
A
109
108
X201
16.93MHz
MUTE 20
M402
SLED
MOTOR
M
SL+
SL–
CH3OUTF
17
CH3OUTR
18
SLED
MOTOR
DRIVE
CH3INF
23
CH3INR
22
M401
SPINDLE
MOTOR
M
SP+
SP–
16 CH4OUTF
CH4OUTR
15
SPINDLE
MOTOR
DRIVE
CH4IN
24
OPOUT
27
SLED/SPINDLE
MOTOR DRIVER,
TRACKING/FOCUS
COIL DRIVER
IC402
OPIN+
2
VREF 26
VC
T901
POWER
TRANSFORMER
S201
(LIMIT)
J901
AC IN
23
38
37
I-DATA-MP3
O-DATA-MP3
O-CLK-MP3
O-XLAT-MP3
O-STBY-MP3
O-RQ-MP3
I-RQ-MP3
I-ACK-MP3
O-CD-XTACN
I-CD-XLAT
O-CD-CMD
O-CD-CLK
I-CD-SENS
I-CD-SCOR
CD-XRST
BAT-CHK-H
36
SYSTEM CONTROLLER
IC801 (1/2)
O-POWER
V-CHECK
18 LID-OPEN
I-CD-CTL
SW2
PUSH
OPEN/
CLOSE
REG-CHK
7 5 6 10 11 12 27 28 26 8 31 30 29 43 4
D901 – 904
RECT
F902
Q801
AC-CHK 45
1
3.3V
5
+3.3V REG
4
IC804,Q802
AC-HI
CD 6V
Signal path
: CD
CD 3.3V
+3.3V
REC/PB
POWER
CONTROL
Q957-959,D957
AUDIO+6V
REG
Q955,D953
RIPPLE
FILTER
Q304
D951
6V
(TAPE)
POWER
SWITCH
Q951
D952
D324
RADIO +B
R-VT
CFD-S03CP/S03CPL
17
U-COM
(VDD)
POWER
SWITCH
Q952,953
9V (SW)
17
BATT
VDD
DRY BATTERY
SIZE "D"
(IEC DESIGNATION R20)
6PCS, 9V
CFD-S03CP/S03CPL
Ver. 1.1
6-2. BLOCK DIAGRAM — MAIN SECTION —
CD_IN_L
L.RO
4
L.LIN
24
A
HRP301
RECORD/PLAYBACK
HEAD
IC302
ELECTRONIC VOLUME
POWER AMP
IC303
REC/PB
PRE AMP
IC301
DET
ALC 2
L.LO
8
20
VOL AMP
L-OUT
L-IN
7
6
L.IN
RADIO L
LOGIC
L.RAD
REC
PB
22
1
RESET
IC805
2
I-KEY2
I-KEY1
I-KEY0
42
41 40 39
1
-1
JC4
2 REG
JC3
KEY NETWORK
Q35
Q32
AM
MIX
KEY0
KEY1
KEY2
AM
IF-IN
T1
5
16 18 17 15
DI
DO
CL
CE
AM
DET
7
AF
BUFFER
CF3
FM
MIX-OUT
RADIO 5V
8
3
Q31
FM
IF-IN
DET-OUT
23
MPX-IN
22
FM
MPX
FM
DET
CF2
ANT2
FM
TELESCOPIC
ANTENNA
29 BO1
30 BO2
AEP MODEL
FM
RF-IN
36
L1
CT1
RADIO 5V
L6
T1
AW
IF
L6
FM
IF
RADIO 5V
FM
RF-OUT FM OSC
34
32
D1
D2
L2
RADIO 5V
L2
FM
FREQUENCY
COVERAGE
CFD-S03CP/S03CPL
18
18
RADIO 5V
R-OUT
13
L-OUT
12
TU_IN_R
S401–407
S411,413–417
S421–424
Signal path
: FM
: AM
: TAPE PLAY
: TAPE REC
: CD
R-ch is omitted due to same as
L-ch.
VCC
6,33
FM-DET
11
RADIO 5V
CT1,L1
FM
TRACKING
19
X IN
X OUT
PD
FM/MW/LW FRONT-END,
IF AMP, DET, FM MPX
IC1
AM
MIX-OUT
FM
OSC
-2
20
FM
MIX
EXCEPT
AEP MODEL
EXCEPT
AEP
MODEL
CT5
AM RF-IN
26
LP-OUT
LP-IN
31
ANT1
MW/LW
FERRITE-ROD
ANTENNA
28 27
D461
AEP,AUS,AR,KR,TW MODEL
R-VT
AM
OSC
AC-HI
REMOTE
CONTROL
RECEIVER
IC401
3
D406
OPR/BATT
Q806
L3
AM OSC
1
Q805,D801,802
X1
75kHz
RADIO 5V
I-RMC 9
9V (SW)
3.3V
Q33
ANT1-2,CT5
LW TRACKING
SW1
(TAPE PLAY)
M901
CAPSTAN/REEL
MOTOR
48
3.3V
FREQUENCY
EXCHANGE
SWITCH
3 24
A-MUTE
TAPE-PLAY
21 22 20 19
17
WAKE-UP
54
AEP MODEL
CT3
9V (SW)
I-SUFFIX
O-TU-DATA
I-TU-COUNT
O-TU-CLK
O-TU-CE
2
VOL-CLK
VOL-DATA
RESET
CD-ON
FM/AM SHIFT
34 33
92
X802
4.19MHz
(VT)
55
93
LIQUID CRYSTAL
DISPLAY PANEL
LCD401
L3
MW/LW
FREQUENCY
COVERAGE
57
X1
ISS2
97–94,89–67,
64,63
6
EEPROM
IC802
ANT1-1,CT3
MW TRACKING
SP201
SPEAKER
(R-CH)
TAPE PLAY
DETECT
Q808
X0
ISS1
62–59
SYSTEM CONTROLLER
IC801 (2/2)
S1
|
S29
TAPE REC
COM1
|
COM4
50
SCL
49
47
D3
SP101
SPEAKER
(L-CH)
M
25
46
5
U-COM
(VDD)
Q303
SAD
+B
6V (TAPE)
i
D322
REC BIAS OSC
Q301
Q302
J321
2
LEVEL
DETECT
D323
TU_IN_R
TAPE
T301
R-CH
5 4
16
TU_IN_L
21
TAPE 15
CD
-2
TAPE
-1
R.RAD
6 REF
S301
(REC/PB)
REC
HE301
ERASE HEAD
MUTE
Q124
CLK
DATA
LINE 17
R-CH
MEGA
BASS
SWITCH
Q122
R-CH
R.LO 18
5
L-CH
M-BASS
(Page 17)
CD_IN_R
R.RO
9
R.IN
8
R.LIN
14
RADIO+B
Abbreviation
AUS : Australian model
AR : Argentina model
KR : Korea model
TW : Taiwan model
CFD-S03CP/S03CPL
Ver. 1.2
6-3. CIRCUIT BOARDS LOCATION
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
POWER board
HEADPHONE board
BD83S board
BATTERY-1 board
KEY-1 board
TC board
KEY-2 board
• Waveforms
— BD83S Board — (CD PLAY)
3
IC201 1 (LRCK)
5
IC201 td (TEO)
3.2 Vp-p
IC201 u; (RFACO)
1.1 +0.3
–0.2 Vp-p
1.7 V
Approx. 1 Vp-p
22.6 µsec
1 V/div, 10 µsec/div
1 V/div, 5 msec/div
500 mV/div, 0.5 µsec/div
2
4
6
IC201 5 (BCK)
IC201 tg (FEO)
3.2 Vp-p
Approx. 150 mVp-p
0.47 µsec
1 V/div, 200 nsec/div
100 mV/div, 5 msec/div
1 V/div, 20 nsec/div
— TC Board — (REC)
2
IC1 w; (X OUT)
1 V/div, 5 µsec/div
1
IC801 os (X1)
2.2 Vp-p
75 kHz
3.3 Vp-p
16.95 MHz
— MAIN Board —
1
IC201 <z/, (XTAO)
1.7 V
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• W : indicates side identified with part number.
f
•
: internal component.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
4.13 MHz (AM)
4.17 MHz (EXCEPT AM)
1 V/div, 100 nsec/div
2
Q301 C
HRP301 (YEL)
35 Vp-p
3.5 Vp-p
3.4 Vp-p
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
• A : B+ Line.
• H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
– BD83S Board –
no mark : CD PLAY
– MAIN (1/3) Board –
no mark : FM
(
) : AM
– MAIN (2/3), (3/3) and Other Boards –
no mark : FM
(
) : PB
<
> : REC
[
] : CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
f : AM
E : PB
a : REC
J : CD PLAY
• Abbreviation
CND : Canadian model.
CET : East European & Russian model.
E41 : AC 230V area in E model.
E92 : AC 120V area in E model.
AUS : Australian model.
KR
: Korea model
MX
: Mexican model.
SP
: Singapore model.
IT
: Italian model.
AR
: Argentina model.
TH
: Thai model.
TW : Taiwan model.
BATTERY-2 board
1
For printed wiring boards.
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
f
: internal component.
• C : panel designation.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
MAIN board
PANEL board
For schematic diagrams.
18.2 µsec
18.2 µsec
1 V/div, 10 µsec/div
10 V/div, 10 µsec/div
CFD-S03CP/S03CPL
19
19
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
C
These are omitted.
Q
B E
Q
B
C
E
These are omitted.
Q
B
C
E
• Abbreviation
CND : Canadian model.
CET : East European & Russian model.
E41 : AC 230V area in E model.
E92 : AC 120V area in E model.
AUS : Australian model.
KR
: Korea model
MX
: Mexican model.
SP
: Singapore model.
IT
: Italian model.
AR
: Argentina model.
TH
: Thai model.
TW : Taiwan model.
CFD-S03CP/S03CPL
6-4. PRINTED WIRING BOARD — BD83S SECTION — • Refer to page 19 for Circuit Boards Location.
1
2
3
4
5
6
: Uses unleaded solder.
7
8
9
10
11
12
13
14
A
(Page 22)
MAIN BOARD
CN805
A
B
R201
R401
M402
(SLED)
CN102
M
C227
IC402
C404
C405
C424
C101
C102
C108
R280
C112
C113
IC202
2
3
C110
R207
1
R202
C203
R111
C202
C
R112
R113
B8
C201
C111
C226
C401
91
R103
30
31
61
60
C224
C251
B10
1-868-067-
11
(11)
C256
FEI
C252
C253
1-868-067-
G
H
CFD-S03CP/S03CPL
20
20
CN301
APC
R254
R252
VC
C207
C258
RFACI
RFACO
TEI
C323
C260
C208
R101
R266
C265
C273
C264
R257
R324
F
R268
C261
R258
R250
R108
R109
R107
R102
C205
C221
90
R278
C303
C230
R105
100
IC201
R451
R452
R267
C103
R104
C104
C107
C109
C105
C301 C304
C213 C222
C214
1
C451
M401
(SPINDLE)
R270
C217
C254
C257
R322
R321
C274
R256
R323
B CE
C232
C206
C220
Q321
M
C291
R292
C218
R253
R255
C272
C210
C271
C219
R260
C321
C322
R110
R277
R275
C215
C266
C267
C275
C268
C277
R276
C223
E
S201
(LIMIT)
C276
R203
B7
R271
B9
C292
R421
C204
R291
D
R265
C406
R423
X201
11
(11)
OPTICAL
PICK-UP
BLOCK
(KSS-213C)
CFD-S03CP/S03CPL
6-5. SCHEMATIC DIAGRAM — BD83S SECTION — • Refer to page 19 for Waveforms. • Refer to page 32 for IC Block Diagram. • Refer to page 34 for IC Pin Description of IC201.
C210
CN301
C301
R260
C273
C264
R257
C260
C265 R265
C322
R256 C208
R250
C230
R324
C303
C274
C258
R258
C261
R267
R323
TP1
R268
IC202
R266
R322
Q321
C257
C221
R321
C323
C304
C321
C256
R207
R202
C227
C226
C203
C222
C204
C207
C254
R255
TP4
R254
C213
C223
TP3
C253
C252
R253
R252
C251
C214
C206 C205
X201 C266
C232
C267
IC201
C268
R271
R270
C275
C215
R203
C217
C201
C291
R291
R451
R452
C202
C292
R292
TP2
C276
C277
C424
C451
R423
C404
R421
C218
C219
CN102
R113
IC B/D
R112
R111
C220 C224
IC402
R201
R276
C272 C271
R275
R277
R278
R110
R103
(Page 24)
R105
C401
R104
C405
C406
R109
R108
R280
R107
R102
R101
M402
C107
C109
C104
C103
C105
C102
C101
C110
C108
C111
C113
R401
C112
M401
S201
CFD-S03CP/S03CPL
21
21
CFD-S03CP/S03CPL
Ver. 1.4
6-6. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 19 for Circuit Boards Location.
4
5
6
7
8
ANT2
FM TERESCOPIC
ANTENNA
(Page 26)
HP BOARD
CN307
E
F
CN305
JW101
JW102
JW103
JW121
+
C112
R245
+
R316
C354
C356
R324
C324
R323
R243
1
JW117
C206
3
C355
C108
R144
C119
C106
R143
+
C130
C110
C125
C231
Q224
C208
C225
C229
JW104
JW105
JW134
C323
C957
C232
R235
R234
JW129
C357
JW138
JW137
JW106
JW128
D957
R965
R959
C959
R333
JW132
JW131
JW142
JW169
JW133
JW148
R328 R321
R879
JW182
R162
BD83S BOARD
CN102
(Page 20)
R873
JW151
FB831
JW118
JW119
R872
JW120
R887
R893
JW152
JW124
R875
JW150
R876
JW186
FB832
JW147
JW156
R813
R803
R801
Q452
R452
R867
R866
R864
R865
R863
R862
R861
R860
C453
R856
Q451
C815
C816
R857
C455
C457
E CB
R858
C458
E CB
C456
C451
C454
C836
R878
R451
R453
C452
JC101
JC102
R871
JW154
C818
JW158
R804
CN805
JW153
JW155
JW157
JW190
JW159
R817
C813
R488
A
R859
D322
JW195
JW161
JW163
JW162
JW164
JW165
C814
R809
JW166
JW181
R478
JC103
C808
R262
R880
R814
C811
R868
JW199
R874
R877
C331
JW144
JW145
JW107
R475
JW140
JW149
JW196
JW197
R892
R492
R843
R842
R841
R839
R840
R838
R836
R837
4
Q124
R831
R490
R835
C227
R961
R962
R330
C330
JW177
R338
R337
JW178 R336
R479
JW201
R811
C821
JW204
R896
JW202
R888
JW198
R829
R820
R482
JW213
R951
JW136
C311
R332
R331
JW206
C823
JW205
D801
R894
R481
R826
R827
C325
JW125
JW126
R956
R960
JW180
JW143
JW184
JW183
JW185
R476
C822
JW228
JW212
JW230
JW233
JW210
R483
R898
JW215
12
R855
R491
JW200
CN804
C819
R844
R899
JW179
R845
R854
R849
R851
R847
C162
CN803
R850
R846
1
X802
JW160
C817
1
R824
R853
4
C131
R141
R136 E C B
C132
R805
R852
CN304
R466
JW141
JW174
JW175
JW110
JW189
JW229
JW192
JW193
JW194
JC807
R467
R815
R889
L804
JW222
D462
JW172
JW139
C36
R23
JW191
JW211
JW216
R480
JW234
JW236
JW235
JW221
JW237
JW238
JW225
JW239
JW240
JW242
JW244
JW248
JW250
C261
JW214
B
C804
JW249
C820
C825
JW256
JW255
R486
R484
R463
R261
R161
C161
B CE
6
R142
R327
0
FFC802
R897
R810
80
CN806
14
R816
R819
81
C262
Q808
D461
R464
10
C129
10
R885
R472
R465
9
R139
R147
1
JW257
+
R145
IC303
R812
R818
R825
C807
7
R135
C115
C212
R242
JW130
BCE
JW146
C210
C322
R239
1
JW247
R462
Q222
Q122
JW116
C219
R329
L803
C461
C806
AEP,AUS,
KR,AR,TW
MODEL
C127
R140
R477
R821
R822
R241
E CB
B CE
80
JW246
R461
R886
4
5
IC805
R802
R823
Q959
+
R238
R134
C117
R335
R891
C230
R247
IC
R473
1
UK,E41,CET,
IT,SP,TH
MODEL
C350
R240
R244
D323
30
R471
R474
3
Q801
D802
IC302
C113
E C B
R138
51
R487
CND,AEP,E92,AUS,
MX,KR,AR,TW MODEL
AEP,AUS,
KR,AR,TW
MODEL
Q805
Q806
C349
C213
R236
50
G
JW171
R954
R24
D6
JW187
R22
R17
C217
Q957
C215
31
R869
JW245
R870
IC802
R828
R493
JC2
JC3
JW254
EXCEPT AEP
MODEL
H
1
3
IC804
TYPE A
C805
ANT1
JC1
AEP MODEL
R884
C
3
JW241
4
R830
E
5
2
-2
R883
C803
1
Q802
JC4
TYPE B
IC806
Q304 B C E
C358
Q951
C961
B CE
R958
D952
AEP MODEL
-1
C956
JW135 R957
JW203
JW227
R31
R32
C30
Q32
C52
E
L6
T1
R953
R952
R14
C19
C18
C39
R18
R10
C68
C72
C37
R28
C27
R20
R41
R29
Q958
JW127
B CE
R325
R21
C32
C51
Q31
JC804
JW188
R16
C69
C28
C25
C35
Q953
E
+
R36
CF2
JW209
R30
R34
R19
R955
R326
JW108
C38
C31
C26
R35
R25
C54
CT3
ANT1
MW/LW
FERRITE BAR
ANTENNA
C29
CF3
Q35
R39
C4
JW208
C22
C34
JW220
C53
C55
CT5
D324
C326
C40
CND,E92,MX
MODEL
C24
D
D951
C953
C42
IC1
C23
C70
JW219
JW226
C20
C41
R26
R38
C64
JW217
JW218
R27 C43
C
+
L1
C3
R37
R5
C9
X1
Q952
BCE
Q33
C61
D3
C67
C60
C62
R6
R15
C1
C63
C12
R12
B
D953
C952
C46
C45
C33
D1
C21
C11
C10
JW207
C13
R4
C7
R1
C15
R13
R3
R7
JW223
CT1
C2
4
CN306
JW170
C17
R9
C16
C5
R2
R11 JW224
C6
C14
C
L2
1
JW168
Q955
L3
14
3
C951
JW231
D2
13
(Page 30)
1
D4
AEP MODEL
12
POWER BOARD
CN901
R963
B
11
JW167
D5
JW232
10
C353
A
F
9
JW176
3
R964
2
1
: Uses unleaded solder.
R848
1-869-160-
I
B
TC BOARD
CN301
(Page 26)
M
SW2
Z/PUSH
OPEN/CLOSE
C
PANEL BOARD
FFC402
(Page 28)
(Page 28)
M801
SW1
(LEAF SW) (CAPSTAN/REEL MOTOR)
J
Refer to NOTE FOR REPLACEMENT OF THE
IC804 AND IC806 on page 4 for type A and B.
CFD-S03CP/S03CPL
D
PANEL BOARD
FFC401
• Semiconductor Location
Ref. No.
D1
D2
D3
D4
D5
D6
D322
D323
D324
22
Location
C-4
B-4
D-3
B-5
B-5
C-6
E-10
C-12
C-7
Ref. No.
D461
D462
D801
D802
D951
D952
D953
D957
22
Location
H-5
H-5
G-7
G-7
C-8
C-9
C-8
C-10
Ref. No.
IC1
IC302
IC303
IC801
IC802
IC804
IC805
IC806
Location
C-5
E-9
D-12
G-10
G-3
F-5
H-4
F-4
Ref. No.
Q31
Q32
Q33
Q35
Q122
Q124
Q222
Q224
Q304
Location
E-3
E-3
C-3
D-3
D-11
E-11
D-11
C-11
C-9
Ref. No.
Q451
Q452
Q801
Q802
Q805
Q806
Q808
Q951
Q952
Location
H-12
G-11
G-6
F-5
F-7
G-6
H-6
C-8
B-9
Ref. No.
Q953
Q955
Q957
Q958
Q959
Location
C-9
B-7
C-11
C-10
D-10
11
(11)
CFD-S03CP/S03CPL
Ver. 1.2
6-7. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 19 for Waveforms. • Refer to page 32 for IC Block Diagram.
(CND,E92,MX)
(EXCEPT CND,E92,MX)
R30
(CND,E92,MX)
(EXCEPT CND,E92,MX)
R35
R11
L3
C2
R1
CT1
C3
Q33
C20
R9
L1
C1
R3
C5
C6
C61
C41
C39
C46
C42
C43
C18
R13
R7
L2
C17
R27
X1
C19
C64
R38
C62
C11
R2
C45
C63
C10
C4
C67
C40
C14
D1
C69
C68
R37
D2
C13 C15
R14
C16
C7
R36
R24
R12
R4
R39
R15
C60
C12
R6
R5
C9
D3
C53
IC B/D
C55
R34
C54
Q35
D6
IC1
CT5
CT3
JC2
JC3
Q32
JC1
R32
ANT1
R22
C52
ANT2
T1
C26
R19
R20
R21
CF2
C72
C37
(Page 24)
CND,E92,MX MODEL
CFD-S03CP/S03CPL
23
C38
R17
R10
C34
C30
C24
C32
C70
C33
C29
C31
C21
R26
C35
R41
R29
C23
C28
C22
R16
C36
C27
JC4
CF3
R25
C51
R31
D5
R18
R28
C25
D4
R23
L6
Q31
23
CFD-S03CP/S03CPL
Ver. 1.4
6-8. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 19 for Waveforms. • Refer to page 37 for IC Pin Description of IC801.
R490
C823
C822
C821
R492
CN807
CN804
R870
R817
R491
R836
R488
R835
R838
R837
R840
R839
C815
R842
R841
R845
R844
R843
R847
R846
R849
R848
R852
R851
C455
R850
R854
R819
R853
C456
R818
IC802
R869
R484
Q451
C454
C457
C453
C820
UK,E41,CET,IT,SP,TH MODEL
R820
R855
R161
R261
C458
C451
JC804
R452
(Page 23)
C452
Q452
R826
R856
R451
R453
R898
R857
Q805
(Page 29)
R827
R858
R481
R860
R802
R862
R824
R482
R863
R823
IC801
C819
R821
R825
X802
R471
R830
R864
TYPE A
Q802
R829
R865
R828
R866
R480
R867
R472
(Page 27)
CN803
R822
R868
C806
R886
AEP,AUS,KR,
AR,TW MODEL
D802
Q806
R861
R885
D801
IC805
C161
FFC802
C261
R859
R483
(AEP,AUS,KR,TW)
(CND,E92,MX,AR)
R815
R816
C814
R473
Q801
R474
(AEP,AR)
(AUS,KR,TW)
R461
R486
D461
(Page 29)
R463
R801
R803
R804
IC804
R462
R884
R883
R814
R813
R812
R811
R810
C818
R809
C807
C805
R831
C808
R805
C262
C162
C825
C803
C816
C813
L803
C811
R487
C461
R464
R466
R465
R467
D462
R479
L804
C804
R476
R478
R493
SW2
R894
R896
R893
CN806
R162
R262
TYPE B
CN805
IC806
XC6202P332FR
IC806
R889
R475
R892
(Page 25)
R880
R891
R887
R888
R879
R477
R878
R877
R876
R875
R874
FB832
FB831
R873
R872
R871
Refer to NOTE FOR REPLACEMENT OF THE
IC804 AND IC806 on page 4 for type A and B.
CFD-S03CP/S03CPL
24
24
(Page 21)
CFD-S03CP/S03CPL
6-9. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 32 for IC Block Diagrams.
C323
R134
C129
C132
R135
R144
C112
CN306
CN307
Q124
C108
R147
J321
C119
R143
R330
R329
R328
R321
C216 C116
C355
R142
Q122
IC B/D
R316
IC302
R139
R145
C110
R136
R138
IC B/D
R245
C324
R324
C130
R140
C131
C115
C113
D323
R323
C125
C106
C127
R148 R146
R141
R248
IC303
C206
R239
C225
C227
R246
C356
C331
R241
CN308
C213
R247
Q222
C208
Q224
SP101
C219
C212
R238
C215
R235 R236
R242
R240
R335
C230
R336
C330
C311
C353
R234
C229
R244
R243
R337
C217
R338
SP201
C117
C231
C232
C322
C210
C354
D322
R327
C349
C350
R332
CN305
R331
(Page 31)
R964
R963
Q955
R962
R961
Q952
R951
(Page 24)
Q957
C325
Q953
R958
Q951
R955
R959
Q958
R953
R954
C951
R325
R960
D324
R952
Q304
R956
R326
C326
R965
D957
C358
C959
C952
C357
D953
R333
C961
C953
C957
Q959
CN304
JC807
Q808
R897
M901
R899
C817
SW1
CFD-S03CP/S03CPL
25
25
D951
R957
C956
D952
CFD-S03CP/S03CPL
6-10. PRINTED WIRING BOARDS — TC SECTION — • Refer to page 19 for Circuit Boards Location.
2
1
3
4
5
: Uses unleaded solder.
6
7
8
9
10
11
12
13
14
YEL
RED
WHT
BLK
BLK
RED
YEL
WHT
A
R306
R312
R304
R303
JC308
JW303
G
11
(11)
1-869-165-
B
MAIN BOARD
FFC802
H
R148
C116
JC306
JC307
R205
R211
JW302
JW301
R111
R105
R302
CN301
3
2
6
1-869-164-
C312
R309
F
4
7
1
C304
JC303
JC302
JC305
IC301
5
C216
R311
R315
R209
Q303
R208
R203
C205
C203
R201
C201
R207
R204
R212
FB203
FB202
C309
R106
C303
R305
JW304
R206
E
FB204
R301
C301
FB201
R112
C103
C207
C104
FB206
C101
C204
R103
R314
R210
FB205
C107
R202
C302
R109
REC
Q302
C202
R146
JW321
R107
(Page 22)
JW322
R310
R101
R104
S301
(REC/PB)
PB
MAIN BOARD
CN306
R248
R110
C105
SP101
SPEAKER
(L-CH)
R246
C306
R108
D
CN307
CN308
F
T301
C308
R102
SP201
SPEAKER
(R-CH)
Q301
R307
HRP300
RECORD/PLAYBACK
HEAD
S301
C310
HE301
ERASE
HEAD
C102
C307
C
FB207
(R-CH)
C305
(L-CH)
R308
C318
B
(Page 22)
CFD-S03CP/S03CPL
26
26
11
(11)
J321
i
CFD-S03CP/S03CPL
Ver. 1.2
6-11. SCHEMATIC DIAGRAM — TC SECTION — • Refer to page 19 for Waveforms. • Refer to page 33 for IC Block Diagram.
IC B/D
(AEP,UK,CET,KR,IT)
(CND,E41,E92,AUS,MX,SP,AR,TH,TW)
C102
R102
R108
IC301
R103
R104
R112
R109
C301
C103
C104
R301
C107
HRP301
R111
FB201
C101
C105
FB202
R101
R107
R110
JC305 R304
FB203
C303
C309
C302
R303
FB204
HE301
R207
R210
C205
R201
JC306
C312
R211
FB205
C207
FB206
C201
C203
C204
R204
R212
R302
R209
R309
C202
S301
R202
CN301
R203
R208
FB207
JC302
R106
R105
R206
JC303
R205
FFC802
(Page 24)
T301
C318
C310
R305
C305
C308
R314
R315
R306
R312
Q301
Q302
R310
Q303
R311
R308
JC308
C306
C304
C307
R307
CFD-S03CP/S03CPL
27
27
JC307
CFD-S03CP/S03CPL
Ver. 1.1
6-12. PRINTED WIRING BOARDS — PANEL SECTION — • Refer to page 19 for Circuit Boards Location.
3
4
5
6
A
S417
x
B
7
8
(Page 22)
(Page 22)
MAIN BOARD
CN804
MAIN BOARD
CN803
D
C
9
10
11
12
13
S407
BX
IC401
S415
/
TUNE
R415
R413
R409
R416
1
R408
FFC401
20
1
FFC402
R406
R414
S415
S414
S413
S406
D
R402
R401
R403
R404
S401
4
CN403
2
1
D406
1-869-161-
11
(11)
R407
33
S414
S402
S405
20
1
3
R430
R417
R419
JW401
C
S407
R418
S416
SLEEP
R412
/
TUNE
2
C401
MODE
R405
S416
R411
3
S417
14
IC401
R432
R431
2
1
: Uses unleaded solder.
1
LCD401
LIQUID CRYSTAL DISPLAY UNIT
S404
D406
S403
OPR/BATT
S401
z/POWER
(EXCEPT AEP,UK,CET,IT)
>/PRESET
S413
S406
S404
S403
z/OPERATE
./PRESET
REPEAT
DISPLAY/
ENTER
MEGA BASS
(AEP,UK,CET,IT)
E
F
1
G
2
3
4
R422 R421
CN421
R423
FFC411
FFC412
R424
11
1-869-162- (11)
S411
S421
S422
S424
S423
H
11
1-849-163- (11)
CD
TAPE
VOLUME
I
CFD-S03CP/S03CPL
28
28
RADIO/BAND/
AUTO PRESET
CFD-S03CP/S03CPL
Ver. 1.1
6-13. SCHEMATIC DIAGRAM — PANEL SECTION —
R401
S401
R402
S402
R403
R404
S403
S404
R405
R406
S405
R407
R408
R409
S406
S407
(EXCEPT AEP,UK,CET,IT)
OPERATE
(AEP,UK,CET,IT)
S413
R411
R412
S414
R413
R414
S415
R415
S416
R416
R417
S417
R418
FFC412
R419
CN403
CN421
FFC411
S423
S411
S421
RADIO/
BAND/
AUTO
PRESET
D406
R430
R424
R421
LCD401
IC401
C401
R432
FFC402
R431
FFC401
(Page 24)
(Page 24)
CFD-S03CP/S03CPL
29
S424
S422
29
R422
R423
FFC422
CFD-S03CP/S03CPL
6-14. PRINTED WIRING BOARDS — POWER SUPPLY SECTION — • Refer to page 19 for Circuit Boards Location.
1
2
3
4
5
6
7
: Uses unleaded solder.
8
9
10
11
12
13
14
A
FH901
F902
FH902
JW904
T901
JW905
B
D903
JW908
D904
C904
CN901
C902
11
(11)
D902
E
D
CN903
MAIN BOARD
CN305
(Page 22)
C906
C901
1-869-167-
GRY
RED
CN902
C
D901
JW907
C903
–
+
+
–
–
DRY BATTERY
SIZE "D"
(IEC DESIGNATION R20)
6pcs, 9V
+
E
J901
F
11
(11)
- AC IN
1-869-166-
JW903
JW902
JW901
JW900
G
1-869-168-
H
I
CFD-S03CP/S03CPL
30
30
11
(11)
CFD-S03CP/S03CPL
6-15. SCHEMATIC DIAGRAM — POWER SUPPLY SECTION —
CN902
CN903
C901
D901
D902
C902
CN901
T901
C903
F902
D903
J901
FH901
FH902
C906
D904
(Page 25)
C904
CFD-S03CP/S03CPL
31
31
CFD-S03CP/S03CPL
• IC BLOCK DIAGRAMS
AM
RF
AM RF-IN 1
FM
RF
OPOUT
OUTVREF
CH4CAPA
CH4IN
CH3FIN
CH3RIN
GND
MUTE
POWVCC
CH3OUTF
CH3OUTR
CH4OUTF
CH4OUTR
IC1 LV23003VA (MAIN Board (1/3))
PREVCC
IC402 BA5947FM-E2 (BD83S Board)
28
27
26
25
24
23
22
21
20
19
18
17
16
15
36 FM RF-IN
MUTING
D
D
D
D
35 GND2
34 FM RF-OUT
REG 2
FM
MIX
33 VCC2
FM
OSC
GND1 4
32 FM OSC
FM
DET
23 DET-OUT
VREF
FM
S-METER
OPIN–
OPIN+
1 2
SD
IF
BUFFER
3
4
5
6
ST
PIROT
DET
P-DET 9
TRIG
STSW
FF
FF
FF
PHASE
COMPARATOR
P-COMP 10
FM-DET 11
L-OUT 12
R-OUT 13
VCO
DECODER
22 MPX-IN
MUTE
VSS 14
POWER ON
RESET
UNIVERSAL
COUNTER
IC303 TA8227P (MAIN Board (3/3))
L-BS
L-OUT
CTU
6
5
4
3
2
1
7
8
9
10
11
12
R-BS
R-OUT
VCC
REFERENCE
DIVIDER
PREGND
PHASE
DETECTOE
CHARGE
PUMP
RIPPLE
UNLOCK
DETECTOR
L-NF
SWALLOW
COUNTER
R-NF
CCB
I/F
DATA SHIFT
REGISTER
LATCH
L-IN
15
16
17
18
R-IN
CE
DI
CL
DO
21 VDD
PROGRAMMABLE
DIVIDER
20 X OUT
19 X IN
CFD-S03CP/S03CPL
32
32
D
D
D
D
7
8
9
10
11
12
13
14
CH1OUTF
FM
IF
CH1OUTR
FM IF-IN 8
CH2OUTF
24 AM LOW CUT
CH2OUTR
AM
DET
POWVCC
AM
IF
VREFIN
AM IF-IN 7
INTERFACE
GND
AGC
INTERFACE
CH2RIN
LOW-PASS
FILTER
LEVEL SHIFT
CH2FIN
OSC
BUFFER
AM OSC
BO2
BO1
LP-OUT
LP-IN
PD
AGC
CH1RIN
VCC1 6
31
30
29
28
27
26
25
CH1FIN
AM
OSC
SW
AM MIX-OUT 5
+ –
INTERFACE
AM
MIX
+ –
FM-MIX 3
CFD-S03CP/S03CPL
IC302 PT2257-S (MAIN Board (3/3))
L-IN
L-OUT
VDD
CLK
8
7
6
5
VREF
LOGIC
CONTROL
VR 2
VOL AMP 2
VOL AMP 1
REF AMP
VR 1
1
2
3
4
R-IN
R-OUT
GND
DATA
IC301 TA2068N (TC Board)
AGC 1
LINE
NAB
AMP1 BUF AMP
A1
L.NF 3
R.IN 8
RADIO
BUF AMP MUTE MONITOR
AMP
B1
DET
2.1
ALC2 ALC1
REF
AMP
BUF AMP
B2
REC
AMP2
ON
7dB
ON
7dB
MIC
AMP1
MIC.NF 12
MUTE
TAPE
RADIO
MONITOR
AMP
BUF AMP
A2
16 R.RAD
15 TAPE
TAPE
NAB
AMP2
LOGIC 19 VCC
17 LINE
ON
26dB
R.NF 10
20 L.LO
18 R.LO
MUTE
R.RO 9
R.PO 11
22 L.RAD
21 REC
26dB
L.IN 5
GND 7
23 MIC I/EX
TAPE
REC
AMP1
L.RO 4
REF 6
24 L.LIN
TAPE
L.PO 2
LINE
14 R.LIN
13 MIC
33
CFD-S03CP/S03CPL
• IC PIN DESCRIPTIONS
• IC201 CXD3014A-201R (RF AMP, SYSTEM SERVO PROCESSOR, DIGITAL SIGNAL PROCESSOR) (BD83S BOARD)
Pin No.
Pin Name
I/O
1
LRCK
O
2
LRCKI
I
L/R sampling clock signal input terminal
3
PCMD
O
Serial data output terminal
4
PCMDI
I
Serial data input terminal
5
BCK
O
Bit clock signal output terminal
6
BCKI
I
Bit clock signal input terminal
7
XTACN
I
8
XRST
I
9
VSS
—
Ground terminal
10
IREQ-MP3
O
MP3 data request signal output to the system controller
11
CLOK
I
CD serial data transfer clock signal input from the system controller
12
DATA2
I
MP3 serial data input/output with the system controller
13
XLAT-MP3
I
MP3 serial data latch pulse signal input from the system controller
14
REQ-MP3
I
MP3 data request signal input from the system controller
15
ACK-MP3
O
MP3 acknowledge signal output to the system controller
16
XLAT
I
CD serial data latch pulse signal input from the system controller
17
VDD
—
Power supply terminal (+1.8V)
18
SVSS
—
Ground terminal
19
SVDD
—
Power supply terminal (+1.8V)
34
Pin Description
L/R sampling clock signal output terminal
Oscillation circuit on/off switch control signal input from the system controller
“L”: oscillation stop, “H”: self-oscillation
System reset signal input from the system controller
“L”: reset
20
SENS
O
Internal status (SENSE) signal output to the system controller
21
WFCK
—
Not used
22
XUGF
—
Not used
23
XPCK
—
Not used
24
GFS
—
Not used
25
C2PO
—
Not used
26
SCOR
O
Subcode sync (S0+S1) detection signal output to the system controller
27
VDD
—
Power supply terminal (+1.8V)
28
COUT
—
Not used
29
SVSS
—
Ground terminal
30
SVDD
—
Power supply terminal (+1.8V)
31
MIRR
—
Not used
32
DFCT
—
Not used
33
FOK
—
Not used
34
VSS
—
Ground terminal
35
VDD
—
Power supply terminal (+1.8V)
36
VSS
—
Ground terminal
37
MIRR
—
Not used
38
MDP
O
Spindle motor servo control signal output terminal
Disc inner position detection signal input terminal
39
SSTP
I
40
IOVSS1
—
Ground terminal
41
SFDR
O
Sled servo drive signal (+) output to the coil/motor driver
42
SRDR
O
Sled servo drive signal (–) output to the coil/motor driver
43
TFDR
O
Tracking servo drive signal (+) output to the coil/motor driver
44
TRDR
O
Tracking servo drive signal (–) output to the coil/motor driver
45
FFDR
O
Focus servo drive signal (+) output to the coil/motor driver
46
FRDR
O
Focus servo drive signal (–) output to the coil/motor driver
47
IOVDD1
—
Power supply terminal (+3.3V)
CFD-S03CP/S03CPL
Pin No.
Pin Name
I/O
48
AVDD0
—
Power supply terminal (+3.3V)
Pin Description
49
AVSS0
—
Ground terminal
50
E
I
E signal input from the optical pick-up block
51
F
I
F signal input from the optical pick-up block
52
TEI
I
Tracking error signal input terminal
53
TEO
O
Tracking error signal output terminal
54
FEI
I
Focus error signal input terminal
55
FEO
O
Focus error signal output terminal
56
VC
O
Middle point voltage output terminal
57
A
I
A signal input from the optical pick-up block
58
B
I
B signal input from the optical pick-up block
59
C
I
C signal input from the optical pick-up block
60
D
I
D signal input from the optical pick-up block
61
AVDD4
—
Power supply terminal (+3.3V)
62
RFDCO
O
Not used
63
PDSENS
I
Not used
64
AC_SUM
O
RFAC summing amplifier signal output terminal
65
EQ_IN
I
RF equalizer circuit input terminal
66
LD
O
Laser diode on/off control signal output to the automatic power control circuit
“L”: laser off, “H”: laser on
67
PD
I
Light amount monitor input from the optical pick-up block laser diode
68
RFC
I
Equalizer cut off frequency adjustment terminal
69
AVSS4
—
Ground terminal
70
RFACO
O
EFM signal output terminal
71
RFACI
I
EFM signal input terminal
72
AVDD3
—
73
BIAS
I
Power supply terminal (+3.3V)
Asymmetry circuit constant current input terminal
74
ASYI
I
Playback EFM asymmetry comparator voltage input terminal
75
ASYO
O
Playback EFM full-swing output terminal
76
VPCO
O
Charge pump output terminal for broad-band EFM PLL
77
VCTL
I
VCO2 control voltage input terminal for broad-band EFM PLL
78
AVSS3
—
79
CLTV
I
VCO1 control voltage input terminal for multiplier
80
FILO
O
Filter output terminal for master PLL
Ground terminal
81
FILI
I
Filter input terminal for master PLL
82
PCO
O
Charge pump output terminal for master PLL
83
SVSS
—
Ground terminal
84
SVDD
—
Power supply terminal (+1.8V)
85
SSTB-MP3
I
86
VDD
—
Power supply terminal (+1.8V)
87
VSS
—
Ground terminal
88
TEST1
I
Test terminal
89
DATA
I
CD serial data input from the system controller
MP3 standby on/off control signal input terminal
“L”: standby
Not used
Normally: fixed at “L”
90
CLK2
I
91
SVSS
—
Ground terminal
MP3 serial data transfer clock signal input from the system controller
92
SVDD
—
Power supply terminal (+2.5V)
93
JTAGTCK
—
Not used
94
JTAGTDI
—
Not used
95
JTAGTDO
—
Not used
96
JTAGTMS
—
Not used
35
CFD-S03CP/S03CPL
Pin No.
Pin Name
I/O
97
TRST
—
36
Pin Description
Not used
98
VSS
—
Ground terminal
99
VDD
—
Power supply terminal (+1.8V)
100
IOVDD2
—
Power supply terminal (+3.3V)
101
DOUT
O
Digital audio signal output terminal
102
TEST
I
Test terminal
Normally: fixed at “L”
Test terminal
Normally: fixed at “L”
Not used
103
TES1
I
104
IOVSS2
—
105
PLLVDD
—
Power supply terminal (+1.8V)
106
PLLVSS
—
Ground terminal
107
XVSS
—
Ground terminal
108
XTAO
O
System clock output terminal (16.9344 MHz)
109
XTAI
I
System clock input terminal (16.9344 MHz)
Ground terminal
110
XVDD
—
Power supply terminal (+1.8V)
111
AVDD1
—
Power supply terminal (+3.3V)
112
AOUT1
O
L-ch analog audio signal output terminal
113
VREFL
O
L-ch reference voltage output terminal
114
AVSS1
—
Ground terminal
115
AVSS2
—
Ground terminal
116
VREFR
O
R-ch reference voltage output terminal
117
AOUT2
O
R-ch analog audio signal output terminal
118
AVDD1
—
Power supply terminal (+3.3V)
119
IOVDD0
—
Power supply terminal (+3.3V)
120
IOVSS0
—
Ground terminal
CFD-S03CP/S03CPL
• IC801 MB90802NPF-G-109E1 (SYSTEM CONTROL) (MAIN BOARD (2/3))
Pin No.
Pin Name
I/O
Pin Description
1
O-POWER
O
2
FM/AM SHIFT
O
system clock shift control signal output
3
A-MUTE
O
A-mute signal output
System power control output
H: Power ON
H: mute on
4
CD-XRST
O
CD reset signal output
5
O-DATA-MP3
O
MP3 serial data output
6
O-CLK-MP3
O
MP3 serial transfer clock output
7
I-DATA-MP3
I
MP3 serial data input
8
I-CD-XLAT
I
CD LAT signal output
9
I-RMC
I
Remote commander receiver data input
10
O-XLAT-MP3
O
MP3 LAT signal output
11
O-STBY-MP3
O
CD mechanical mute signal output
12
O-RQ-MP3
O
MP3 chip select signal output
13
X0A
—
Not used (Open)
14
X1A
—
Not used (Open)
15
VCC
—
Power supply (+3.3 V)
16
VSS
—
Ground
17
M-BASS
O
MEGA BASS control signal output
18
LID-OPEN
I
CD door open/close switch input
19
O-TU-CE
O
Tuner PLL chip enable signal output
20
O-TU-CLK
O
Tuner PLL serial transfer clock output
21
O-TU-DATA
O
Tuner PLL serial data output
22
I-TU-COUNT
I
Tuner PLL serial data input
23
O-CD-CLT
O
CD power control signal output
24
TAPE PLAY
I
Tape play switch signal input
L: Close
H: CD ON
25
TAPE REC
I
Tape record switch signal input
26
O-CD-XTCN
O
CD DSP oscillation control signal output
H: REC
27
I-RQ-MP3
I
MP3 REQ signal input
28
I-ACK-MP3
I
MP3 acknowledgment detect signal input
29
I-CD-SENS
I
CD SENS signal input
30
O-CD-CLK
O
CD command transfer clock output
31
O-CD-CMD
O
CD command data output
32
AVCC
—
Power supply (+3.3 V)
33
VOL DATA
O
Volume command serial data output
34
VOL CLK
O
Volume command serial transfer clock output
35
AGND
—
Ground
36
REQ-CHK
I
37
BTT-CHK-H
I
Power supply 9V check signal input
38
V-CHECK
I
Power supply 6V check signal input
39
I-KEY0
I
Key input
40
I-KEY1
I
Key input
41
I-KET2
I
Key input
Power supply CD 3.3V check signal input
42
WAKE-UP
I
Key wake-up signal input
43
I-CD-SCOR
I
CD Q-data request signal input
44
VSS
—
45
AC-CHK
I
46
SDA
I/O
47
SCL
O
EEPROM transfer clock output
48
I-SUFFIX
I
Suffix distinction input
49
ISS1
O
ISS control signal output
Ground
AC IN check signal input
EEPROM serial data input/output
37
CFD-S03CP/S03CPL
Pin No.
Pin Name
I/O
50
ISS2
O
ISS control signal output
Pin Description
51
MD2
I
Operation mode setting pin
52
MD1
I
Operation mode setting pin
53
MD0
I
Operation mode setting pin
54
RESET
I
System reset signal input
55
CD-ON
O
Audio CD mode control signal output
56
TU-ON
—
Not used (Open)
57
TAPE
O
Audio tape mode control signal output
58
VLCD
—
Not used (Open)
59 to 62
COM4 to 4
O
LCD drive common signal output
63
SEG29
O
LCD drive segment signal output
64
SEG28
O
LCD drive segment signal output
65
VCC
—
Power supply (+3.3 V)
66
VSS
—
Ground
67 to 89
SEG27 to 5
O
LCD drive segment signal output
90
VCC
—
Power supply (+3.3 V)
91
VSS
—
Ground
92
X1
O
Main system oscillation output (4.19 MHz)
93
X0
I
Main system oscillation input (4.19 MHz)
94 to 97
SEG4 to 1
O
LCD drive segment signal output
99 to 100
NC
—
Not used (Open)
38
CFD-S03CP/S03CPL
Ver. 1.6
SECTION 7
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
7-1.
•
•
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Accessories are given in the last of this parts list.
Abbreviation
CND : Canadian model
CET : East European & Russian model
E41 : AC 230V area in E model
E92 : AC 120V area in E model
AUS : Australian model
KR
: Korea model
MX : Mexican model
SP
: Singapore model
IT
: Italian model
AR
: Argentina model
TH
: Thai model
TW
: Taiwan model
REAR CABINET SECTION
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
1
ANT2
11
11
10
3
T901
2
3
9
3
3
F902
8
3
5
3
3
3
7
5
6
11
3
6
4
11
3
Ref. No.
1
Part No.
Description
Remark
1
1
2
2-654-054-01 LID, BATTERY (GRAY)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
2-654-054-11 LID, BATTERY (LIGHT GRAY)...(SILVER)
(AEP,UK,CET,IT,MX)
2-654-054-21 LID, BATTERY (WHITE)...(WHITE) (MX)
2-654-054-31 LID, BATTERY (PINK)...(PINK) (MX)
3-252-833-01 SCREW (M3), (+) P
3
4
5
6
7
3-252-827-01
A-1157-013-A
3-229-975-01
3-252-540-01
2-654-073-01
8
9
9
A-1157-012-A BATTERY-2 BOARD, COMPLETE
A-1157-015-A POWER BOARD, COMPLETE (E92,MX)
A-1157-362-A POWER BOARD, COMPLETE
(EXCEPT CND,E92,MX,TW)
1
SCREW (B2.6), (+) BV TAPPING
BATTERY-1 BOARD, COMPLETE
SPRING, BATTERY (–)
SPRING (+.–), BATTERY
TERMINAL, ANTENNA
Ref. No.
9
9
10
10
10
Part No.
Description
Remark
A-1157-370-A POWER BOARD, COMPLETE (CND)
A-1157-380-A POWER BOARD, COMPLETE (TW)
2-654-040-02 CABINET (REAR) (GRAY)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
2-654-040-32 CABINET (REAR) (LIGHT GRAY)...(SILVER)
(AEP,UK,CET,IT,MX)
2-654-040-61 CABINET (REAR) (WHITE)...(WHITE) (MX)
10
11
ANT2
0 F902
0 T901
2-654-040-71
3-831-441-99
1-754-376-11
1-533-468-12
1-443-861-11
CABINET (REAR) (PINK)...(PINK) (MX)
SHEET (1)
ANTENNA, TELESCOPIC (FM)
FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)
TRANSFORMER, POWER
(EXCEPT CND,E92,MX,TW)
0 T901
1-443-871-11 TRANSFORMER, POWER (CND,E92,MX,TW)
39
CFD-S03CP/S03CPL
Ver. 1.6
67
7-2.
FRONT CABINET SECTION (1)
70
A
58
51
52
59
60
57
61
62
51
68
65
63
not supplied
56
69
64
not supplied
A
63
51
55
53
51
51
52
66
54
Ref. No.
51
52
53
54
55
55
55
55
56
57
Part No.
Description
3-252-827-01
2-655-159-02
3-047-468-01
2-654-071-01
X-2103-302-2
SCREW (B2.6), (+) BV TAPPING
JOINT, CABINET
DAMPER
SPRING, CASSETTE
HOLDER SUB ASSY, CASSETTE
(BLUE)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
Remark
Ref. No.
59
X-2103-333-2 HOLDER SUB ASSY, CASSETTE
(GRAY)...(SILVER) (UK,CET,IT,MX)
X-2103-334-1 HOLDER SUB ASSY, CASSETTE
(GRAY)...(SILVER) (AEP)
X-2186-760-1 HOLDER SUB ASSY, CASSETTE
(WHITE)...(WHITE,PINK) (MX)
A-1283-378-A MF-S01//C (including M901)
2-654-047-01 BUTTON (PAUSE) (GRAY)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
61
60
60
60
61
61
62
62
57
57
58
58
58
59
59
40
2-654-047-11 BUTTON (PAUSE) (GRAY)...(SILVER)
(AEP,UK,CET,IT,MX)
2-654-047-21 BUTTON (PAUSE)
(LIGHT GRAY)...(WHITE,PINK) (MX)
2-654-046-01 BUTTON (STOP) (GRAY)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
2-654-046-11 BUTTON (STOP) (GRAY)...(SILVER)
(AEP,UK,CET,IT,MX)
2-654-046-21 BUTTON (STOP) (LIGHT GRAY)...(WHITE,PINK)
(MX)
2-654-045-01 BUTTON (REW) (GRAY)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
2-654-045-11 BUTTON (REW) (GRAY)...(SILVER)
(AEP,UK,CET,IT,MX)
62
63
64
64
Part No.
Description
Remark
2-654-045-21 BUTTON (REW) (LIGHT GRAY)...(WHITE,PINK)
(MX)
2-654-044-01 BUTTON (FF) (GRAY)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
2-654-044-11 BUTTON (FF) (GRAY)...(SILVER)
(AEP,UK,CET,IT,MX)
2-654-044-21 BUTTON (FF) (LIGHT GRAY)...(WHITE,PINK)
(MX)
2-654-042-01 BUTTON (PLAY) (GRAY)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
2-654-042-11 BUTTON (PLAY) (GRAY)...(SILVER)
(AEP,UK,CET,IT,MX)
2-654-042-21 BUTTON (PLAY) (LIGHT GRAY)...(WHITE,PINK)
(MX)
2-654-043-01 BUTTON (REC) (GRAY)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
2-654-043-11 BUTTON (REC) (GRAY)...(SILVER)
(AEP,UK,CET,IT,MX)
2-654-043-21 BUTTON (REC) (LIGHT GRAY)...(WHITE,PINK)
(MX)
65
66
3-254-029-01 SCREW
A-1156-999-A TC BOARD, COMPLETE (AEP,UK,CET,IT,KR)
A-1158-597-A TC BOARD, COMPLETE
(CND,E41,E92,AUS,MX,SP,AR,TH,TW)
3-253-143-01 SCREW (B2.6), (+) P TAPPING
3-923-151-01 CUSHION, RUBBER
67
68
69
70
3-254-141-01
2-670-389-01
3-214-817-01
3-254-140-01
SCREW (B2.6), (+) BV TAPPING
BELT (1)
BELT (FR)
SCREW (B2.6), (+) BV TAPPING
CFD-S03CP/S03CPL
Ver. 1.6
7-3.
FRONT CABINET SECTION (2)
101
106
106
105
102
not supplied
106
104
103
SP201
106
108
102
107
not supplied
106
SP101
106
109
110
Ref. No.
Part No.
Description
101
102
103
104
105
A-1157-000-A
3-831-441-99
1-831-616-11
1-831-613-11
2-654-050-02
KEY-1 BOARD, COMPLETE
SHEET (1)
CABLE, FLEXIBLE FLAT (4 CORE)
CABLE, FLEXIBLE FLAT (4 CORE)
BUTTON (FUNC) (BLUE)...(GRAY,SILVER)
105
106
107
108
2-654-050-31
3-252-827-01
A-1157-002-A
2-654-051-01
108
108
108
109
Remark
BUTTON (FUNC) (WHITE)...(WHITE,PINK)
SCREW (B2.6), (+) BV TAPPING
KEY-2 BOARD, COMPLETE
BUTTON (VOLUME) (GRAY)...(GRAY)
(CND,E41,E92,MX,AR)
2-654-051-11 BUTTON (VOLUME) (LIGHT GRAY)...(SILVER)
(EXCEPT CND,E41,E92,MX,AR,TW,MX)
2-654-051-21 BUTTON (VOLUME) (WHITE)...(WHITE) (MX)
2-654-051-31 BUTTON (VOLUME) (PINK)...(PINK) (MX)
X-2102-579-1 CABINET (FRONT) SUB ASSY
(GUNMETALLIC)...(GRAY) (CND)
Ref. No.
109
109
109
109
109
109
110
SP101
SP201
Part No.
Description
Remark
X-2103-199-1 CABINET (FRONT) SUB ASSY
(SILVER)...(SILVER) (AEP,UK,CET,IT)
X-2103-301-1 CABINET (FRONT) SUB ASSY
(GUNMETALLIC)...(GRAY) (E41,E92,MX,AR)
X-2103-331-1 CABINET (FRONT) SUB ASSY
(SILVER)...(SILVER) (AUS,KR,SP,TH,TW,CET)
X-2186-747-1 CABINET (FRONT) SUB ASSY
(SILVER)...(SILVER) (MX)
X-2186-759-1 CABINET (FRONT) SUB ASSY
(WHITE)...(WHITE) (MX)
X-2186-764-1 CABINET (FRONT) SUB ASSY
(PINK)...(PINK) (MX)
3-040-916-01 FOOT (FRONT), RUBBER
1-826-280-11 SPEAKER (7.7cm) (L-CH)
1-826-280-11 SPEAKER (7.7cm) (R-CH)
41
CFD-S03CP/S03CPL
Ver. 1.6
7-4.
UPPER CABINET SECTION (1)
151
155
152
156
153
161
154
157
158
SW2
159
162
160
158
158
158
Ref. No.
151
151
151
152
153
154
155
Part No.
Description
Remark
2-654-053-21 LID, CD (GRAY)...(SILVER) (AEP,UK,CET,IT,MX)
2-654-053-31 LID, CD (BLUE)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
2-654-053-81 LID, CD (WHITE)...(WHITE,PINK) (MX)
1-452-899-11 MAGNET
3-019-395-01 PLATE, CHUCKING
155
155
156
3-253-143-01 SCREW (B2.6), (+) P TAPPING
2-654-056-01 HANDLE (BLUE)...(GRAY,SILVER)
(CND.E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
2-654-056-11 HANDLE (GRAY)...(SILVER) (AEP,UK,CET,IT,MX)
2-654-056-21 HANDLE (WHITE)...(WHITE,PINK) (MX)
2-654-072-01 SPRING, CD
157
3-047-468-21 DAMPER
Ref. No.
Part No.
Description
158
159
159
159
159
3-252-827-01
A-1157-008-A
A-1157-365-A
A-1157-386-A
A-1157-391-A
SCREW (B2.6), (+) BV TAPPING
MAIN BOARD, COMPLETE (CND,E92,MX)
MAIN BOARD, COMPLETE (E41,SP,TH)
MAIN BOARD, COMPLETE (UK,CET,IT)
MAIN BOARD, COMPLETE (AEP)
Remark
159
159
160
161
162
A-1157-967-A
A-1157-973-A
1-832-008-11
3-923-151-01
2-674-958-01
MAIN BOARD, COMPLETE (AUS,KR,TW)
MAIN BOARD, COMPLETE (AR)
CABLE, FLEXIBLE FLAT (14 CORE)
CUSHION, RUBBER
PAPER (MAIN), SHIELD
SW2
1-692-960-21 SWITCH, PUSH (1 KEY)
(Z PUSH OPEN/CLOSE)
42
CFD-S03CP/S03CPL
Ver. 1.6
7-5.
UPPER CABINET SECTION (2)
217
215
216
214
201
210
212
IC401
202
218
213
LCD401
213
203
205
206
213
204
S201
203
208
#1
211
211
209
Ref. No.
Part No.
Description
201
202
203
204
205
3-923-736-01
3-931-379-21
3-931-379-31
1-832-404-21
1-831-973-21
COVER, CD
RUBBER, VIBRATION PROOF (RED)
RUBBER, VIBRATION PROOF (GREEN)
CABLE, FLEXIBLE FLAT (16 CORE)
CABLE, FLEXIBLE FLAT (23 CORE)
214
214
215
216
206
207
208
209
210
A-1134-279-A
3-252-827-01
2-654-055-21
3-254-151-01
A-1157-006-A
BD83S BOARD, COMPLETE
SCREW (B2.6), (+) BV TAPPING
CHASSIS, CD
SCREW (B2.6), (+) P TAPPING
PANEL BOARD, COMPLETE
216
211
212
213
214
1-832-009-11
2-673-399-01
3-831-441-99
2-654-058-01
Remark
Ref. No.
216
216
214
214
207
207
209
CABLE, FLEXIBLE FLAT (20 CORE)
SHEET (IR), ADHESIVE
SHEET (1)
WINDOW, LCD (CLEAR)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW)
2-654-058-12 WINDOW, LCD (GLASS)...(SILVER)
(AEP,UK,CET,IT)
217
218
IC401
Part No.
Description
Remark
2-654-058-31
2-654-058-41
A-1154-900-A
X-2103-303-2
WINDOW, LCD (CLEAR)...(SILVER,PINK) (MX)
WINDOW, LCD (GLASS)...(WHITE) (MX)
HEADPHONE BOARD, COMPLETE
CABINET (UPPER) SUB ASSY
(BLUE)...(GRAY,SILVER)
(CND,E41,E92,AUS,KR,MX,SP,AR,TH,TW,CET)
X-2103-332-2 CABINET (UPPER) SUB ASSY
(GRAY)...(SILVER) (AEP,UK,CET,IT)
X-2186-748-1 CABINET (UPPER) SUB ASSY
(GRAY)...(SILVER) (MX)
X-2186-761-1 CABINET (UPPER) SUB ASSY
(WHITE)...(WHITE,PINK) (MX)
3-831-441-11 CUSHION (D)
2-654-085-01 HOLDER, IR
6-600-108-01 IC RPM7140 (IR)
LCD401 1-802-046-11 DISPLAY PANEL, LIQUID CRYSTAL
S201
1-771-853-11 SWITCH, DETECTION (LIMIT)
#1
7-685-853-04 SCREW +BVTT 2X6 (S)
2-654-058-21 WINDOW, LCD (CLEAR)...(SILVER) (CET)
43
CFD-S03CP/S03CPL
7-6.
CD MECHANISM SECTION
(KSM-213CDP)
251
not supplied
256
252
253
255
254
not supplied
(M701 (SPINDLE))
M702
Ref. No.
251
252
253
254
44
Part No.
Description
2-626-907-11
2-627-003-01
2-174-500-01
2-626-908-01
GEAR (A)
GEAR (B) (RP)
SCREW (2X3)
SHAFT, SLED
Remark
Ref. No.
255
0 256
M702
Part No.
Description
Remark
X-2162-709-2 CHASSIS ASSY (CDP), MOTOR (SPINDLE)
(including M701)
8-848-483-12 OPTICAL PICK-UP (KSS-213C/C2RP)
X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)
CFD-S03CP/S03CPL
SECTION 8
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
Ref. No.
Part No.
•
•
•
CAPACITORS
uF : µF
COILS
uH : µH
Abbreviation
CND : Canadian model
CET : East European & Russian model
E41 : AC 230V area in E model
E92 : AC 120V area in E model
AUS : Australian model
KR
: Korea model
MX : Mexican model
SP
: Singapore model
IT
: Italian model
AR
: Argentina model
TH
: Thai model
TW
: Taiwan model
Description
Remark
A-1157-013-A BATTERY-1 BOARD, COMPLETE
**************************
3-229-975-01 SPRING, BATTERY (–)
Ref. No.
BATTERY-1
Ver. 1.2
BATTERY-2
BD83S
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
When indicating parts by reference
number, please include the board.
Part No.
Description
Remark
C220
C221
C222
C223
C224
1-164-360-11
1-164-360-11
1-164-360-11
1-164-360-11
1-164-360-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
C226
C227
C230
C232
C251
1-165-908-11
1-165-908-11
1-162-927-11
1-164-360-11
1-164-315-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
100PF
0.1uF
470PF
10%
10%
5%
5%
10V
10V
50V
16V
50V
C252
C253
C254
C256
C257
1-162-968-11
1-164-315-11
1-162-968-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
470PF
0.0047uF
0.1uF
0.1uF
10%
5%
10%
10%
10%
50V
50V
50V
16V
16V
C258
C260
C261
C264
C265
1-164-230-11
1-117-863-11
1-162-970-11
1-162-964-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.47uF
0.01uF
0.001uF
0.1uF
5%
10%
10%
10%
10%
50V
6.3V
25V
50V
16V
C266
C267
C268
C271
C272
1-162-915-11
1-162-910-11
1-162-915-11
1-107-826-11
1-164-360-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10PF
5PF
10PF
0.1uF
0.1uF
0.5PF
0.25PF
0.5PF
10%
50V
50V
50V
16V
16V
C273
C274
C275
C276
C277
1-164-315-11
1-107-826-11
1-162-910-11
1-165-908-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
0.1uF
5PF
1uF
1uF
5%
10%
0.25PF
10%
10%
50V
16V
50V
10V
10V
C291
C292
C301
C303
C304
1-164-315-11
1-164-315-11
1-164-360-11
1-137-710-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
470PF
0.1uF
10uF
1uF
5%
5%
50V
50V
16V
6.3V
10V
C321
C322
C323
C401
C404
1-162-964-11
1-165-908-11
1-128-995-21
1-128-394-11
1-164-360-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
0.001uF
1uF
100uF
220uF
0.1uF
10%
10%
20%
20%
C405
C406
C424
C451
1-164-360-11
1-164-360-11
1-164-360-11
1-165-176-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.047uF
16V
16V
16V
16V
16V
< CONNECTOR >
CN903 1-815-550-11 PIN, CONNECTOR (PWB) 2P
*************************************************************
A-1157-012-A BATTERY-2 BOARD, COMPLETE
**************************
3-229-975-01 SPRING, BATTERY (–)
*************************************************************
A-1134-279-A BD83S BOARD, COMPLETE
**********************
< CAPACITOR >
C101
C102
C103
C104
C105
1-162-919-11
1-162-919-11
1-162-919-11
1-164-230-11
1-162-919-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
22PF
22PF
220PF
22PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C107
C108
C109
C110
C111
1-164-230-11
1-164-230-11
1-164-230-11
1-164-230-11
1-164-230-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
220PF
220PF
220PF
220PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C112
C113
C201
C202
C203
1-162-919-11
1-162-919-11
1-128-995-21
1-164-360-11
1-128-995-21
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
22PF
22PF
100uF
0.1uF
100uF
5%
5%
20%
50V
50V
10V
16V
10V
C204
C205
C206
C207
C208
1-164-360-11
1-164-360-11
1-164-360-11
1-128-995-21
1-164-360-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
100uF
0.1uF
C210
C213
C214
C215
C217
1-164-360-11
1-164-360-11
1-164-360-11
1-164-360-11
1-164-360-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
16V
16V
16V
16V
16V
C218
C219
1-164-360-11 CERAMIC CHIP
1-164-360-11 CERAMIC CHIP
0.1uF
0.1uF
16V
16V
20%
20%
16V
16V
16V
10V
16V
20%
10%
10%
50V
10V
10V
10V
16V
16V
16V
16V
16V
45
CFD-S03CP/S03CPL
BD83S
Ref. No.
HEADPHONE
Part No.
KEY-1
KEY-2
Description
Remark
< CONNECTOR >
CN102
CN301
Ref. No.
R423
R451
R452
1-770-706-21 CONNECTOR, FFC/FPC 23P
1-770-425-51 CONNECTOR, FFC/FPC 16P
Part No.
Description
1-216-833-11 METAL CHIP
1-216-837-11 METAL CHIP
1-216-833-11 METAL CHIP
Remark
10K
22K
10K
5%
5%
5%
1/10W
1/10W
1/10W
< VIBRATOR >
< IC >
IC201
IC202
IC402
X201
1-795-101-21 VIBRATOR, CERAMIC (16.93MHz)
*************************************************************
8-753-246-30 IC CXD3014A-201R
6-708-736-01 IC BD18KA5FP-E2
6-705-808-01 IC BA5947FM-E2
A-1154-900-A HEADPHONE BOARD, COMPLETE
***************************
< TRANSISTOR >
< CAPACITOR >
Q321
6-551-120-01 TRANSISTOR 2SA2119K
C116
C216
< RESISTOR >
R101
R102
R103
R104
R105
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R107
R108
R109
R110
R111
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R112
R113
R201
R202
R203
1-216-809-11
1-216-809-11
1-216-295-11
1-216-295-11
1-500-445-21
METAL CHIP
100
5%
METAL CHIP
100
5%
SHORT CHIP
0
SHORT CHIP
0
FERRITE, EMI (SMD) (2012)
1/10W
1/10W
R207
R250
R252
R253
R254
1-216-295-11
1-216-857-11
1-216-833-11
1-216-821-11
1-216-833-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
1M
10K
1K
10K
R255
R256
R257
R258
R260
1-216-821-11
1-216-837-11
1-216-845-11
1-216-849-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
R265
R266
R267
R268
R270
1-216-829-11
1-216-821-11
1-216-829-11
1-216-833-11
1-216-821-11
R271
R275
R276
R277
R278
1-162-964-11 CERAMIC CHIP
1-162-964-11 CERAMIC CHIP
0.001uF
0.001uF
10%
10%
50V
50V
< CONNECTOR >
CN308
1-815-445-11 PIN, CONNECTOR (PWB) 4P
< JACK >
J321
1-815-325-11 JACK (i)
< RESISTOR >
R146
1-216-809-11 METAL CHIP
100
5%
1/10W
R148
1-216-805-11 METAL CHIP
47
5%
1/10W
R246
1-216-809-11 METAL CHIP
100
5%
1/10W
R248
1-216-805-11 METAL CHIP
47
5%
1/10W
*************************************************************
A-1157-000-A KEY-1 BOARD, COMPLETE
*********************
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1K
22K
100K
220K
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
1K
4.7K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1-216-857-11
1-216-809-11
1-216-841-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
100
47K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R280
R291
R292
R321
R322
1-216-864-11
1-216-809-11
1-216-809-11
1-216-789-11
1-216-789-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100
100
2.2
2.2
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R323
R324
R401
R421
1-216-864-11
1-216-845-11
1-216-295-11
1-216-864-11
SHORT CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
0
100K
0
0
5%
1/10W
1-831-613-11 CABLE, FLEXIBLE FLAT (4 CORE) (FFC412)
1-831-616-11 CABLE, FLEXIBLE FLAT (4 CORE) (FFC411)
3-831-441-99 SHEET (1)
< RESISTOR >
R421
R422
R423
1-216-813-11 METAL CHIP
1-216-817-11 METAL CHIP
1-216-821-11 METAL CHIP
220
470
1K
5%
5%
5%
1/10W
1/10W
1/10W
< SWITCH >
46
S411
S421
1-786-050-21 SWITCH, KEYBOARD (CD)
1-786-050-21 SWITCH, KEYBOARD
(RADIO/BAND/AUTO PRESET)
S422
1-786-050-21 SWITCH, KEYBOARD (TAPE)
*************************************************************
A-1157-002-A KEY-2 BOARD, COMPLETE
*********************
3-831-441-99 SHEET (1)
< CONNECTOR >
CN421
1-784-726-11 CONNECTOR, FFC 4P
< RESISTOR >
R424
1-216-821-11 METAL CHIP
1K
5%
1/10W
CFD-S03CP/S03CPL
KEY-2
Ref. No.
Part No.
Description
Remark
< SWITCH >
S423
1-786-050-21 SWITCH, KEYBOARD (VOLUME –)
S424
1-786-050-21 SWITCH, KEYBOARD (VOLUME +)
*************************************************************
A-1157-008-A
A-1157-365-A
A-1157-386-A
A-1157-391-A
A-1157-967-A
MAIN BOARD, COMPLETE (CND,E92,MX)
MAIN BOARD, COMPLETE (E41,SP,TH)
MAIN BOARD, COMPLETE (UK,CET,IT)
MAIN BOARD, COMPLETE (AEP)
MAIN BOARD, COMPLETE (AUS,KR,TW)
A-1157-973-A MAIN BOARD, COMPLETE (AR)
*********************
1-832-008-11 CABLE, FLEXIBLE FLAT (14 CORE) (FFC802)
2-674-958-01 PAPER (MAIN), SHIELD
3-254-142-01 SCREW (B3), (+) BV TAPPING
Ref. No.
Part No.
Description
Remark
C33
1-162-968-11 CERAMIC CHIP
C34
C35
C36
C37
1-162-970-11
1-162-968-11
1-162-962-11
1-162-962-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF 10%
50V
(CND,E92,MX)
0.01uF
10%
25V
0.0047uF 10%
50V
470PF
10%
50V
470PF
10%
50V
C38
C39
C40
C41
C42
1-162-927-11
1-126-923-11
1-162-970-11
1-162-915-11
1-162-915-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
220uF
0.01uF
10PF
10PF
5%
20%
10%
0.5PF
0.5PF
50V
10V
25V
50V
50V
C43
C45
C46
C51
1-126-964-11
1-162-970-11
1-115-416-11
1-162-970-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.01uF
0.001uF
0.01uF
20%
10%
5%
10%
C52
1-107-826-11 CERAMIC CHIP
0.1uF
10%
50V
25V
25V
25V
(AEP)
16V
(AEP)
C53
1-162-923-11 CERAMIC CHIP
47PF
5%
C54
1-162-923-11 CERAMIC CHIP
47PF
5%
C55
1-162-970-11 CERAMIC CHIP
0.01uF
10%
C60
1-162-970-11 CERAMIC CHIP
0.01uF
10%
C61
1-162-919-11 CERAMIC CHIP
22PF
5%
C62
1-162-927-11 CERAMIC CHIP
100PF
5%
C63
1-164-230-11 CERAMIC CHIP
220PF
5%
C64
1-162-970-11 CERAMIC CHIP
0.01uF
10%
C67
C68
1-162-964-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
0.001uF
0.01uF
10%
10%
C69
1-162-970-11 CERAMIC CHIP
0.01uF
10%
C70
C72
C106
C108
1-162-927-11
1-162-927-11
1-162-966-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
0.0022uF
0.01uF
5%
5%
10%
10%
25V
(AEP)
50V
50V
50V
25V
C110
C112
C113
C115
C117
1-127-715-11
1-126-925-11
1-126-960-11
1-126-960-11
1-162-964-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
0.22uF
470uF
1uF
1uF
0.001uF
10%
20%
20%
20%
10%
16V
10V
50V
50V
50V
C119
C125
C127
C129
C130
1-104-658-11
1-126-959-11
1-125-891-11
1-165-176-11
1-126-957-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
100uF
0.47uF
0.47uF
0.047uF
0.22uF
20%
20%
10%
10%
20%
10V
50V
10V
16V
50V
C131
C132
C161
C162
C206
1-126-947-11
1-164-227-11
1-126-960-11
1-126-960-11
1-162-966-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
47uF
0.022uF
1uF
1uF
0.0022uF
20%
10%
20%
20%
10%
35V
25V
50V
50V
50V
C208
C210
1-162-970-11 CERAMIC CHIP
1-127-715-11 CERAMIC CHIP
0.01uF
0.22uF
10%
10%
25V
16V
< ANTENNA >
ANT1
ANT1
1-754-116-12 ANTENNA, FERRITE-ROD (MW/LW) (AEP)
1-754-117-12 ANTENNA, FERRITE-ROD (AM) (EXCEPT AEP)
< CAPACITOR >
C1
C2
C3
C4
C5
1-162-964-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.01uF
0.01uF
0.01uF
0.01uF
C6
C7
C9
C10
1-162-915-11
1-165-176-11
1-165-176-11
1-162-923-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C10
1-162-927-11 CERAMIC CHIP
10PF
0.5PF 50V
0.047uF 10%
16V
0.047uF 10%
16V
47PF
5%
50V
(EXCEPT CND,E92,MX)
100PF
5%
50V
(CND,E92,MX)
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10%
10%
10%
10%
10%
50V
25V
25V
25V
25V
C11
C12
C13
C14
1-162-927-11
1-164-230-11
1-162-915-11
1-162-910-11
100PF
5%
50V
220PF
5%
50V
10PF
0.5PF 50V
5PF
0.25PF 50V
(EXCEPT CND,E92,MX)
8PF
0.5PF 50V
(CND,E92,MX)
C14
1-162-913-11 CERAMIC CHIP
C15
C16
C17
C18
C19
1-107-826-11
1-125-891-11
1-104-662-11
1-126-963-11
1-126-956-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.1uF
0.47uF
22uF
4.7uF
0.1uF
10%
10%
20%
20%
20%
16V
10V
25V
50V
50V
C20
C21
C22
C23
C24
1-164-315-11
1-162-970-11
1-165-176-11
1-126-947-11
1-165-176-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
470PF
0.01uF
0.047uF
47uF
0.047uF
5%
10%
10%
20%
10%
50V
25V
16V
35V
16V
C25
C26
C27
C28
C29
1-162-927-11
1-115-156-11
1-125-891-11
1-115-156-11
1-126-925-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
100PF
1uF
0.47uF
1uF
470uF
5%
50V
10V
10V
10V
10V
C30
C31
1-126-923-11 ELECT
1-162-968-11 CERAMIC CHIP
C32
1-162-970-11 CERAMIC CHIP
10%
20%
220uF
20%
10V
0.0047uF 10%
50V
(CND,E92,MX)
0.01uF
10%
25V
Ver. 1.2
MAIN
50V
(AEP)
50V
(AEP)
25V
(AEP)
25V
(AEP)
50V
(AEP)
50V
(AEP)
50V
(AEP)
25V
(AEP)
50V
25V
(AEP)
47
CFD-S03CP/S03CPL
Ver. 1.4
MAIN
Ref. No.
Part No.
Description
Part No.
Description
C212
C213
C215
C217
C219
1-126-925-11
1-126-960-11
1-126-960-11
1-162-964-11
1-104-658-11
ELECT
ELECT
ELECT
CERAMIC CHIP
ELECT
470uF
1uF
1uF
0.001uF
100uF
20%
20%
20%
10%
20%
10V
50V
50V
50V
10V
Remark
C952
C953
C956
C957
C959
1-162-974-11
1-126-925-11
1-126-965-11
1-162-974-11
1-126-923-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
C225
C227
C229
C230
C231
1-126-959-11
1-125-891-11
1-165-176-11
1-126-957-11
1-126-947-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.47uF
0.47uF
0.047uF
0.22uF
47uF
20%
10%
10%
20%
20%
50V
10V
16V
50V
35V
C961
1-107-826-11 CERAMIC CHIP
C232
C261
C262
C311
C322
1-164-227-11
1-126-960-11
1-126-960-11
1-126-965-11
1-126-934-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.022uF
1uF
1uF
22uF
220uF
10%
20%
20%
20%
20%
25V
50V
50V
50V
16V
C323
C324
C325
C326
C330
1-126-964-11
1-164-156-11
1-126-937-11
1-126-923-11
1-162-974-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
10uF
0.1uF
4700uF
220uF
0.01uF
20%
50V
25V
16V
10V
50V
C331
C349
C350
C353
C354
1-126-947-11
1-162-915-11
1-162-915-11
1-126-925-11
1-162-964-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
47uF
10PF
10PF
470uF
0.001uF
20%
0.5PF
0.5PF
20%
10%
C355
C356
C357
C358
C451
1-126-767-11
1-107-826-11
1-126-934-11
1-164-156-11
1-162-908-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
1000uF
0.1uF
220uF
0.1uF
3PF
20%
10%
20%
C452
C453
C454
C455
C456
1-162-908-11
1-162-923-11
1-162-923-11
1-162-923-11
1-162-923-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
3PF
47PF
47PF
47PF
47PF
0.25PF
5%
5%
5%
5%
50V
50V
50V
50V
50V
C457
C458
C461
C803
C804
1-162-970-11
1-162-970-11
1-126-964-11
1-164-156-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
10uF
0.1uF
1uF
10%
10%
20%
25V
25V
50V
25V
10V
C805
C806
C807
C808
C811
1-104-658-11
1-115-156-11
1-162-970-11
1-104-658-11
1-216-864-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
SHORT CHIP
100uF
1uF
0.01uF
100uF
0
20%
10V
10V
25V
10V
C813
C814
C815
C816
C817
1-107-826-11
1-162-970-11
1-162-970-11
1-162-927-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.01uF
100PF
0.1uF
10%
10%
10%
5%
16V
25V
25V
50V
25V
C818
C819
C820
C821
C822
1-162-927-11
1-107-826-11
1-107-826-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.1uF
0.1uF
100PF
100PF
5%
10%
10%
5%
5%
50V
16V
16V
50V
50V
C823
C825
C951
1-162-927-11 CERAMIC CHIP
1-115-156-11 CERAMIC CHIP
1-162-974-11 CERAMIC CHIP
100PF
1uF
0.01uF
5%
50V
10V
50V
20%
20%
Ref. No.
Remark
0.01uF
470uF
22uF
0.01uF
220uF
0.1uF
20%
50V
10V
50V
50V
10V
10%
16V
20%
20%
< FILTER >
CF2
CF3
1-767-555-11 FILTER, CERAMIC
1-781-962-21 FILTER, CERAMIC
< CONNECTOR >
CN304
CN305
CN306
CN803
CN804
1-815-552-11
1-815-551-11
1-815-552-11
1-784-742-11
1-784-742-11
PIN, CONNECTOR (PWB) 4P
PIN, CONNECTOR (PWB) 3P
PIN, CONNECTOR (PWB) 4P
CONNECTOR, FFC 20P
CONNECTOR, FFC 20P
CN805
1-779-291-11 CONNECTOR, FFC (LIF(NON-ZIF)) 23P
< TRIMMER >
35V
50V
50V
10V
50V
CT1
CT3
CT5
1-141-304-21 CAP, CERAMIC TRIMMER 10PF
1-141-442-91 CAP, CERAMIC TRIMMER 20PF
1-141-459-11 CAP, TRIMMER (SEAL TYPE) 45PF (AEP)
< DIODE >
48
16V
16V
16V
25V
0.25PF 50V
10%
20%
D1
D2
D3
D4
D5
6-501-440-01
6-501-440-01
6-501-392-01
8-719-991-33
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
SVC707-AL
SVC707-AL
SVC386-AL
1SS133T-77
1SS133T-77
D6
D322
D323
D324
D461
6-500-697-01
8-719-991-33
8-719-988-61
8-719-991-33
6-500-335-01
DIODE
DIODE
DIODE
DIODE
DIODE
UDZSTE-173.3B
1SS133T-77
1SS355TE-17
1SS133T-77
MC2838-T112-1
D462
D801
D802
D951
D952
8-719-069-54
8-719-991-33
6-500-334-01
6-500-334-01
8-719-991-33
DIODE
DIODE
DIODE
DIODE
DIODE
UDZSTE-175.1B
1SS133T-77
MC2836-T112-1
MC2836-T112-1
1SS133T-77
D953
D957
8-719-978-33 DIODE DTZ-TT11-6.8B
8-719-083-58 DIODE UDZSTE-173.9B
< FERRITE BEAD >
Refer to NOTE FOR REPLACEMENT OF THE
IC804 AND IC806 on page 4 for type A and B.
FB831
FB832
1-216-864-11 SHORT CHIP
0
1-500-445-21 FERRITE, EMI (SMD) (2012)
< IC >
IC1
IC302
IC303
IC801
IC802
6-708-840-01
6-701-919-01
6-703-710-01
6-806-232-01
6-703-740-01
IC
IC
IC
IC
IC
LV23003VA
PT2257-S
TA8227P
MB90802NPF-G-109E1
S-24CS02AFT-TB-G
IC804
IC805
IC806
8-759-679-43 IC S-816A33AMC-BAI-T2-G (TYPE A)
6-704-118-01 IC S-80828CNMC-B8NT2G
6-706-338-01 IC XC6202P332FR (TYPE B)
CFD-S03CP/S03CPL
Ver. 1.1
MAIN
Ref. No.
Part No.
Description
Remark
Part No.
Description
R16
R17
R18
R19
R20
1-216-864-11
1-216-864-11
1-216-809-11
1-216-809-11
1-216-809-11
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
100
100
100
5%
5%
5%
1/10W
1/10W
1/10W
R21
R22
R23
R24
R25
1-216-809-11
1-216-829-11
1-216-817-11
1-216-829-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
4.7K
470
4.7K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R26
R27
R28
R29
R30
1-216-813-11
1-216-833-11
1-216-825-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
10K
2.2K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
(AEP)
R31
1-216-833-11 METAL CHIP
10K
5%
< TRANSISTOR >
R32
1-216-845-11 METAL CHIP
100K
5%
R34
1-216-833-11 METAL CHIP
10K
5%
R35
1-216-829-11 METAL CHIP
4.7K
5%
R36
1-216-845-11 METAL CHIP
100K
5%
1/10W
(AEP)
1/10W
(AEP)
1/10W
(AEP)
1/10W
(AEP)
1/10W
(AEP)
R37
1-216-853-11 METAL CHIP
470K
5%
R38
1-216-829-11 METAL CHIP
4.7K
5%
R39
R41
R134
1-216-864-11 SHORT CHIP
1-216-837-11 METAL CHIP
1-216-813-11 METAL CHIP
0
22K
220
5%
5%
1/10W
1/10W
R135
R136
R138
R139
R140
1-216-825-11
1-216-864-11
1-216-817-11
1-216-833-11
1-216-821-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
0
470
10K
1K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R141
R142
R143
R144
R145
1-216-841-11
1-216-821-11
1-216-809-11
1-216-789-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
1K
100
2.2
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R147
R161
R162
R234
R235
1-216-833-11
1-216-841-11
1-216-864-11
1-216-813-11
1-216-825-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
10K
47K
0
220
2.2K
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R236
R238
R239
R240
R241
1-216-864-11
1-216-817-11
1-216-833-11
1-216-821-11
1-216-841-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
470
10K
1K
47K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R242
R243
R244
R245
R247
1-216-821-11
1-216-809-11
1-216-789-11
1-216-829-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100
2.2
4.7K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R261
1-216-841-11 METAL CHIP
47K
5%
1/10W
< JUMPER RESISTOR >
JC1
JC2
JC3
JC4
JC101
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0 (EXCEPT AEP)
0 (AEP)
0 (EXCEPT AEP)
0 (EXCEPT AEP)
0
JC102
JC103
JC804
JC807
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
< COIL >
L1
L2
L3
L6
L803
1-419-847-11
1-419-655-11
1-411-199-31
1-457-168-11
1-410-521-11
COIL, AIR-CORE
COIL, AIR-CORE
COIL, MW/LW OSC
COIL, DET
INDUCTOR
100uH
Q31
Q32
Q33
Q35
Q122
8-729-054-77
8-729-920-31
8-729-054-77
8-729-601-58
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC4098-T106-PQ (AEP)
DTC343TK (AEP)
2SC4098-T106-PQ (AEP)
2SC3053-C (AEP)
2SC1623-L5L6
Q124
Q222
Q224
Q304
Q451
8-729-120-28
8-729-120-28
8-729-120-28
8-729-120-28
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1623-L5L6
2SC1623-L5L6
2SC1623-L5L6
2SC1623-L5L6
2SC1623-L5L6
Q452
Q801
Q802
Q805
Q806
8-729-120-28
6-551-445-01
8-729-037-03
8-729-600-22
6-551-444-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1623-L5L6
RT1N44QC-TP-1
KTA1266GR-AT
2SA1235-F
RT1N436C-TP-1
(AEP,AUS,KR,AR,TW)
Q808
Q951
Q952
Q953
Q955
8-729-120-28
6-551-444-01
8-729-040-76
8-729-120-28
8-729-018-99
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1623-L5L6
RT1N436C-TP-1
KTA1273-Y-AT
2SC1623-L5L6
2SD2394-F
Q957
Q958
Q959
6-550-542-01 TRANSISTOR 2SD999-T1-AZ
6-551-443-01 TRANSISTOR RT1P436C-TP-1
8-729-027-46 TRANSISTOR DTC114YKA-T146
< RESISTOR >
R1
R2
R3
R4
R5
1-216-845-11
1-216-837-11
1-216-829-11
1-216-797-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
22K
4.7K
10
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R6
R7
R9
R10
R11
1-216-853-11
1-216-797-11
1-216-829-11
1-216-801-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
10
4.7K
22
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R12
R13
R14
R15
1-216-825-11
1-216-825-11
1-216-833-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
10K
22K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
Ref. No.
Remark
1/10W
(AEP)
1/10W
(AEP)
49
CFD-S03CP/S03CPL
Ver. 1.2
MAIN
Ref. No.
Part No.
Description
R262
R316
R321
R323
R324
1-216-864-11
1-216-864-11
1-216-809-11
1-216-857-11
1-216-833-11
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
100
1M
10K
Part No.
Description
1/10W
1/10W
1/10W
R813
R814
R815
R816
R817
1-216-821-11
1-216-821-11
1-216-809-11
1-216-809-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
100
100
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
5%
5%
5%
R325
R326
R327
R328
R329
1-216-821-11
1-216-821-11
1-216-821-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R818
R819
R820
R821
R822
1-216-821-11
1-216-821-11
1-216-853-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
470K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R330
R331
R332
R333
R335
1-216-809-11
1-216-817-11
1-216-817-11
1-216-821-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
470
470
1K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R823
R824
R825
R826
1-216-821-11
1-216-821-11
1-216-821-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
470
R826
1-216-829-11 METAL CHIP
4.7K
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
(CND,E92,MX,AR)
5%
1/10W
(AEP,AUS,KR,TW)
R336
R337
R338
R451
R452
1-216-833-11
1-216-833-11
1-216-833-11
1-216-821-11
1-216-821-11
R827
1-216-817-11 METAL CHIP
470
5%
R827
1-216-829-11 METAL CHIP
4.7K
5%
R453
R461
R462
R463
R464
1-216-833-11
1-216-817-11
1-216-817-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
470
470
470
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R828
R829
R830
1-216-829-11 METAL CHIP
1-216-829-11 METAL CHIP
1-216-829-11 METAL CHIP
4.7K
4.7K
4.7K
5%
5%
5%
R465
R466
R467
R471
R472
1-216-817-11
1-216-817-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
470
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R831
R835
R836
R837
R838
1-216-821-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R473
R474
R475
R476
R477
1-216-821-11
1-216-821-11
1-216-821-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R839
R840
R841
R842
R843
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R478
R479
R480
R481
R482
1-216-841-11
1-216-833-11
1-216-841-11
1-216-841-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
10K
47K
47K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R844
R845
R846
R847
R848
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R483
R484
R486
R487
R488
1-216-841-11
1-216-841-11
1-216-845-11
1-216-845-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
100K
100K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R849
R850
R851
R852
R853
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R490
R491
R492
R493
R801
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-821-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
0
0
0
0
1K
R854
R855
R856
R857
R858
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
5%
1/10W
R802
R803
R804
R805
R809
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R859
R860
R861
R862
R863
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R810
R811
R812
1-216-821-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
10K
1K
5%
5%
5%
1/10W
1/10W
1/10W
R864
R865
R866
R867
R868
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
50
Remark
Ref. No.
Remark
1/10W
(AUS,KR,TW)
1/10W
(AEP,AR)
1/10W
1/10W
1/10W
CFD-S03CP/S03CPL
MAIN
Ref. No.
Part No.
Description
R869
R870
R871
R872
R873
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
R874
R875
R876
R877
R878
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R879
R880
R883
R884
1-216-821-11
1-216-821-11
1-216-845-11
1-216-849-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
100K
220K
5%
5%
5%
5%
R885
1-216-821-11 METAL CHIP
1K
5%
1/10W
1/10W
1/10W
1/10W
(TYPE A)
1/10W
(TYPE A)
R886
R887
R888
R889
R891
1-216-841-11
1-216-837-11
1-216-837-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
22K
22K
10K
47K
5%
5%
5%
5%
5%
R892
R893
R894
R896
R897
1-216-864-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
10K
10K
10K
10K
R898
1-216-817-11 METAL CHIP
470
R899
R951
R952
R953
1-216-825-11
1-216-841-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
47K
2.2K
2.2K
R954
R955
R956
R957
R958
1-216-821-11
1-216-821-11
1-216-833-11
1-216-833-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10K
10K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R959
R960
R961
R962
R963
1-216-809-11
1-216-821-11
1-216-825-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
1K
2.2K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R964
R965
1-216-825-11 METAL CHIP
1-216-833-11 METAL CHIP
2.2K
10K
5%
5%
1/10W
1/10W
Ref. No.
Description
Remark
A-1157-006-A PANEL BOARD, COMPLETE
**********************
1-832-009-11 CABLE, FLEXIBLE FLAT (20 CORE)
(FFC401,FFC402)
2-654-085-01 HOLDER, IR
2-673-399-01 SHEET (IR), ADHESIVE
3-831-441-99 SHEET (1)
< CAPACITOR >
C401
1-115-156-11 CERAMIC CHIP
1uF
10V
< CONNECTOR >
CN403
1-784-726-11 CONNECTOR, FFC 4P
< DIODE >
D406
1/10W
1/10W
1/10W
1/10W
1/10W
Part No.
Ver. 1.4
PANEL
8-719-059-97 LED L-34HD (OPR/BATT)
< IC >
IC401
6-600-108-01 IC RPM7140 (IR)
< LIQUID CRYSTAL DISPLAY >
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
5%
1/10W
(UK,E41,CET,IT,SP,TH)
5%
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
LCD401 1-802-046-11 DISPLAY PANEL, LIQUID CRYSTAL
< RESISTOR >
R401
R402
R403
R404
R405
1-216-813-11
1-216-817-11
1-216-821-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
470
1K
1K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R406
R407
R408
R409
R411
1-216-821-11
1-216-825-11
1-216-825-11
1-216-829-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
2.2K
2.2K
4.7K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R412
R413
R414
R415
R416
1-216-817-11
1-216-821-11
1-216-821-11
1-216-825-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
1K
1K
2.2K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R417
R418
R419
R430
R431
1-216-825-11
1-216-825-11
1-216-829-11
1-216-813-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
4.7K
220
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R432
1-216-845-11 METAL CHIP
100K
5%
1/10W
< TRANSFORMER >
T1
1-433-741-11 TRANSFORMER, IF
< SWITCH >
< VIBRATOR >
S401
X1
1-795-449-11 VIBRATOR, CRYSTAL (75kHz)
X802
1-813-175-21 VIBRATOR, CERAMIC (4.19MHz)
*************************************************************
Refer to NOTE FOR REPLACEMENT OF THE
IC804 AND IC806 on page 4 for type A and B.
S402
S403
S404
1-786-050-21 SWITCH, KEYBOARD (z/OPERATE)
(AEP,UK,CET,IT)
1-786-050-21 SWITCH, KEYBOARD (z/POWER)
(EXCEPT AEP,UK,CET,IT)
1-786-050-21 SWITCH, KEYBOARD (SLEEP)
1-786-050-21 SWITCH, KEYBOARD (MEGA BASS)
1-786-050-21 SWITCH, KEYBOARD (DISPLAY/ENTER)
S405
S406
1-786-050-21 SWITCH, KEYBOARD (MODE)
1-786-050-21 SWITCH, KEYBOARD (REPEAT)
S401
51
CFD-S03CP/S03CPL
Ver. 1.2
PANEL
Ref. No.
S407
S413
S414
S415
S416
POWER
TC
Part No.
Description
1-786-050-21
1-786-050-21
1-786-050-21
1-786-050-21
1-786-050-21
SWITCH, KEYBOARD (u)
SWITCH, KEYBOARD (./PRESET –)
SWITCH, KEYBOARD (>/PRESET +)
SWITCH, KEYBOARD ( /TUNE –)
SWITCH, KEYBOARD ( /TUNE +)
Remark
S417
1-786-050-21 SWITCH, KEYBOARD (x)
*************************************************************
A-1157-015-A POWER BOARD, COMPLETE (E92,MX)
A-1157-362-A POWER BOARD, COMPLETE
(EXCEPT CND,E92,MX,TW)
A-1157-370-A POWER BOARD, COMPLETE (CND)
A-1157-380-A POWER BOARD, COMPLETE (TW)
***********************
C901
C902
C903
C904
C906
Ref. No.
Part No.
Description
C305
C306
C307
C308
C309
1-162-962-11
1-162-970-11
1-162-964-11
1-162-927-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
0.01uF
0.001uF
100PF
0.001uF
10%
10%
10%
5%
10%
50V
25V
50V
50V
50V
C310
C312
C318
1-164-230-11 CERAMIC CHIP
1-162-964-11 CERAMIC CHIP
1-162-962-11 CERAMIC CHIP
220PF
0.001uF
470PF
5%
10%
10%
50V
50V
50V
< CONNECTOR >
CN301
FB201
< CAPACITOR >
FB201
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.022uF
0.022uF
0.022uF
0.022uF
10uF
20%
50V
50V
50V
50V
50V
1-784-775-11 CONNECTOR, FFC 14P
< FERRITE BEAD >
1-533-217-41 HOLDER, FUSE
1-162-995-11
1-162-995-11
1-162-995-11
1-162-995-11
1-126-964-11
Remark
FB202
FB202
FB203
1-216-864-11 SHORT CHIP
0
(CND,E41,E92,AUS,MX,SP,AR,TH,TW)
1-414-445-11 FERRITE, EMI (SMD) (1608)
(AEP,UK,CET,KR,IT)
1-216-864-11 SHORT CHIP
0
(CND,E41,E92,AUS,MX,SP,AR,TH,TW)
1-414-445-11 FERRITE, EMI (SMD) (1608)
(AEP,UK,CET,KR,IT)
1-216-864-11 SHORT CHIP
0
(CND,E41,E92,AUS,MX,SP,AR,TH,TW)
< CONNECTOR >
FB203
CN902
1-815-443-11 PIN, CONNECTOR (PWB) 2P
FB204
< DIODE >
FB204
D901
D902
D903
D904
8-719-063-79
8-719-063-79
8-719-063-79
8-719-063-79
DIODE
DIODE
DIODE
DIODE
1N4002B
1N4002B
1N4002B
1N4002B
FB205
FB205
1-414-445-11 FERRITE, EMI (SMD) (1608)
(AEP,UK,CET,KR,IT)
1-216-864-11 SHORT CHIP
0
(CND,E41,E92,AUS,MX,SP,AR,TH,TW)
1-414-445-11 FERRITE, EMI (SMD) (1608)
(AEP,UK,CET,KR,IT)
1-216-864-11 SHORT CHIP
0
(CND,E41,E92,AUS,MX,SP,AR,TH,TW)
1-414-445-11 FERRITE, EMI (SMD) (1608)
(AEP,UK,CET,KR,IT)
< AC INLET >
FB206
0 J901
1-526-818-11 INLET, AC (- AC IN) (E92,MX)
0 J901
1-526-838-11 INLET, AC 2P (- AC IN) (EXCEPT CND,E92,MX)
0 J901
1-540-009-11 INLET, AC (- AC IN) (CND)
*************************************************************
A-1156-999-A TC BOARD, COMPLETE (AEP,UK,CET,KR,IT)
A-1158-597-A TC BOARD, COMPLETE
(CND,E41,E92,AUS,MX,SP,AR,TH,TW)
*******************
FB206
FB207
FB207
< IC >
IC301
< CAPACITOR >
8-759-264-71 IC TA2068N
< JUMPER RESISTOR >
C101
C102
C103
C104
C105
1-162-964-11
1-104-658-11
1-165-176-11
1-162-966-11
1-162-923-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
100uF
0.047uF
0.0022uF
47PF
10%
20%
10%
10%
5%
50V
10V
16V
50V
50V
C107
C201
C202
C203
C204
1-162-962-11
1-162-964-11
1-104-658-11
1-165-176-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
470PF
0.001uF
100uF
0.047uF
0.0022uF
10%
10%
20%
10%
10%
50V
50V
10V
16V
50V
C205
C207
C301
C302
C303
1-162-923-11
1-162-962-11
1-104-658-11
1-104-658-11
1-104-658-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
47PF
470PF
100uF
100uF
100uF
5%
10%
20%
20%
20%
50V
50V
10V
10V
10V
Q301
Q302
Q303
C304
1-126-947-11 ELECT
47uF
20%
35V
R101
52
1-216-864-11 SHORT CHIP
0
(CND,E41,E92,AUS,MX,SP,AR,TH,TW)
1-414-445-11 FERRITE, EMI (SMD) (1608)
(AEP,UK,CET,KR,IT)
1-216-864-11 SHORT CHIP
0
(CND,E41,E92,AUS,MX,SP,AR,TH,TW)
1-414-445-11 FERRITE, EMI (SMD) (1608)
(AEP,UK,CET,KR,IT)
JC302
JC303
JC305
JC306
JC307
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC308
1-216-864-11 SHORT CHIP
0
< TRANSISTOR >
8-729-901-81 TRANSISTOR 2SC2412K-T-146-R
8-729-027-46 TRANSISTOR DTC114YKA-T146
8-729-027-46 TRANSISTOR DTC114YKA-T146
< RESISTOR >
1-216-837-11 METAL CHIP
22K
5%
1/10W
CFD-S03CP/S03CPL
Ver. 1.5
TC
Ref. No.
Part No.
Description
R102
R103
R104
R105
R106
1-216-805-11
1-216-845-11
1-216-825-11
1-216-837-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47
100K
2.2K
22K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
R107
R108
R109
R110
R111
1-216-841-11
1-216-801-11
1-216-849-11
1-216-809-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
22
220K
100
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R112
R201
R202
R203
R204
1-216-821-11
1-216-837-11
1-216-805-11
1-216-845-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
22K
47
100K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
0
0
0
0
0
1-590-342-12
1-769-412-22
1-770-019-61
1-776-985-12
1-782-126-11
CORD, POWER (E92,MX)
CORD, POWER (AEP,CET,E41,IT,SP,TH)
ADAPTOR, CONVERSION PLUG (UK)
CORD, POWER (KR)
CORD, POWER (CND)
R205
R206
R207
R208
R209
1-216-837-11
1-216-825-11
1-216-841-11
1-216-801-11
1-216-849-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
2.2K
47K
22
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
0
0
0
0
1-783-952-21
1-827-945-12
1-827-946-21
1-829-433-11
2-655-836-11
CORD, POWER (AR)
CORD, POWER (AUS)
CORD, POWER (UK)
CORD, POWER (TW)
MANUAL, INSTRUCTION (ENGLISH)
(CND,E92,TW)
R210
R211
R212
R301
R302
1-216-809-11
1-216-833-11
1-216-821-11
1-216-857-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
1K
1M
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R303
R304
R305
R306
R307
1-216-829-11
1-216-821-11
1-216-817-11
1-216-833-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
1K
470
10K
10
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R308
R309
R310
R311
R312
1-216-837-11
1-216-805-11
1-216-857-11
1-216-857-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
47
1M
1M
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R314
R315
1-216-817-11 METAL CHIP
1-216-817-11 METAL CHIP
470
470
5%
5%
1/10W
1/10W
< SWITCH >
S301
1-786-126-11 SWITCH, SLIDE (REC/PB)
Ref. No.
SW2
Part No.
Description
Remark
1-692-960-21 SWITCH, PUSH (1 KEY)
(Z PUSH OPEN/CLOSE)
1-826-280-11 SPEAKER (7.7cm) (L-CH)
1-826-280-11 SPEAKER (7.7cm) (R-CH)
1-443-861-11 TRANSFORMER, POWER
(EXCEPT CND,E92,MX)
0 T901
1-443-871-11 TRANSFORMER, POWER (CND,E92,MX)
*************************************************************
SP101
SP201
0 T901
ACCESSORIES
************
2-655-836-21
2-655-836-31
2-655-836-41
2-655-836-51
MANUAL, INSTRUCTION (SPANISH) (E92,MX)
MANUAL, INSTRUCTION (FRENCH) (AEP,SP)
MANUAL, INSTRUCTION (GERMAN) (AEP)
MANUAL, INSTRUCTION
(DUTCH,PORTUGUESE) (AEP)
2-655-836-61 MANUAL, INSTRUCTION (ITALIAN) (IT)
2-655-836-71 MANUAL, INSTRUCTION (FINNISH,SWEDISH)
(CET)
2-655-836-81 MANUAL, INSTRUCTION (POLISH) (CET)
2-655-836-91 MANUAL, INSTRUCTION (CZECH,HUNGARIAN)
(CET)
2-655-837-11 MANUAL, INSTRUCTION
(SLOVAKIAN,RUSSIAN) (CET)
2-655-837-21 MANUAL, INSTRUCTION (ENGLISH)
(AEP,UK,AUS,KR,E41,AR,SP,TH)
2-655-837-31 MANUAL, INSTRUCTION (KOREAN) (KR)
2-655-837-41 MANUAL, INSTRUCTION
(TRADITIONAL CHINESE) (TW)
2-655-837-51 MANUAL, INSTRUCTION (FRENCH) (CND)
2-655-837-61 MANUAL, INSTRUCTION (SPANISH)
(AEP,E41,AR)
2-655-837-71 MANUAL, INSTRUCTION (UKRAINIAN) (CET)
< TRANSFORMER >
T301
1-416-041-11 TRANSFORMER, BIAS OSCILLATION
*************************************************************
MISCELLANEOUS
***************
56
152
204
205
255
1-797-376-11
1-452-899-11
1-827-992-11
1-831-973-11
X-2162-709-2
DECK, MECHANICAL (including M901)
MAGNET
WIRE (FLAT TYPE) (16 CORE)
CABLE, FLEXIBLE FLAT (23 CORE)
CHASSIS ASSY (CDP), MOTOR (SPINDLE)
(including M701)
0 256
ANT2
0 F902
M702
S201
8-848-483-12
1-754-376-11
1-533-468-12
X-2625-769-1
1-771-853-11
OPTICAL PICK-UP (KSS-213C/C2RP)
ANTENNA, TELESCOPIC (FM)
FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)
GEAR ASSY (MB) (RP), MOTOR (SLED)
SWITCH, DETECTION (LIMIT)
3-238-070-01 LID, BATTERY CASE (for RMT-CE95A/CE95AD)
A-3172-070-A REMOTE COMMANDER (RMT-CE95AD)
(AEP,UK,CET,IT)
A-3172-079-A REMOTE COMMANDER (RMT-CE95A)
(CND,E41,E92,AUS,AR,KR,MX,SP,TH,TW)
53
CFD-S03CP/S03CPL
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Ver.
Date
Description of Revision
1.0
2006.01
New
1.1
2006.02
E41, Australian, Italian, Argentina, Thai and Taiwan model addition.
1.2
2006.03
Canadian model addition.
1.3
2006.04
Silver model addition of blue type to CET model.
1.4
2007.03
Change of 3.3V regulator circuit.
1.5
2007.07
MANUAL, INSTRUCTION of ukrainian is added to East European &
Russian models of CFD-S03CP.
1.6
54
2007.08
Color variation addition to Mexican model (silver, white, pink).
(SPM-07020)
(SPM-07058)