Download SERVICE MANUAL - Audio Design Guide

SCD-XE597
SERVICE MANUAL
AEP Model
UK Model
Ver. 1.3 2006.02
Model Name Using Similar Mechanism
NEW
CD Mechanism Type
CDM66D-DVBU50
Optical Pick-up Name
DBU-3
SPECIFICATIONS
When a Super Audio CD is played
General
Playing frequency range 2 Hz to 100 kHz
Frequency response
2 Hz to 40 kHz (–3 dB)
Dynamic range
100 dB or more
Total harmonic distortion rate
0.0035 % or less
Wow and flutter
Value of measurable limit
(±0.001 % W. PEAK) or
less
Laser
When a CD is played
Mass (approx.)
Frequency response
2 Hz to 20 kHz
Dynamic range
96 dB or more
Total harmonic distortion rate
0.0039 % or less
Wow and flutter
Value of measurable limit
(±0.001 % W. PEAK) or
less
Power requirements
Power consumption
Dimensions (w/h/d)
Semiconductor laser
(Super Audio CD: λ = 650
nm) (CD: λ = 780 nm)
Emission duration:
continuous
230 V AC, 50/60 Hz
15 W
430 × 95 × 283 mm incl.
projecting parts
3.1 kg
Supplied accessories
Audio connecting cord
Remote commander
Battery
Red and White × 2 (1)
RM-SX800 (1)
R6 (size-AA) (2)
Design and specifications are subject to change
without notice.
Output connector
Jack type Output
level
Load
impedance
ANALOG Phono
5.1CH OUT jacks
2 Vrms (at Over 10
50 kilohms) kilohms
Square
DIGITAL
(CD) OUT optical
OPTICAL* output
connector
–18 dBm
(Light
emitting
wave length:
660 nm)
* Output only the audio signals of the CD
SUPER AUDIO CD PLAYER
9-879-005-04
2006B16-1
© 2006.02
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
SCD-XE597
TABLE OF CONTENTS
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
1.
SERVICING NOTES ................................................ 3
2.
GENERAL ................................................................... 4
3.
DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
3-10.
Disassembly Flow ........................................................... 6
Cover ............................................................................... 6
MAIN Board .................................................................... 7
Loading Panel .................................................................. 7
Front Panel Section ......................................................... 8
KEY Board, DISPLAY Board ......................................... 8
CD Mechanism Deck (CDM66D-DVBU50) .................. 9
Base Unit (DVBU50) ...................................................... 9
RF Board, Pick-up Unit (DBU-3) ................................... 10
Belt (LD), LOADING Board, Motor (L) Assy ................ 10
4.
DIAGRAMS
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
4-7.
4-8.
4-9.
4-10.
Block Diagram ................................................................ 12
Printed Wiring Board — RF Section — ......................... 13
Schematic Diagram — RF Section — ........................... 14
Printed Wiring Board — MAIN Section — ................... 15
Schematic Diagram — MAIN Section (1/4) — ............ 16
Schematic Diagram — MAIN Section (2/4) — ............ 17
Schematic Diagram — MAIN Section (3/4) — ............ 18
Schematic Diagram — MAIN Section (4/4) — ............ 19
Printed Wiring Board — DISPLAY Section — ............ 20
Schematic Diagram — DISPLAY Section — ................ 21
5.
TEST MODE ............................................................... 22
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
6.
EXPLODED VIEWS
6-1.
6-2.
6-3.
6-4.
Main Section .................................................................... 23
Front Panel Section ......................................................... 24
CD Mechanism Deck ...................................................... 25
Base Unit (DVBU50) ...................................................... 26
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveform is output three times.
7.
ELECTRICAL PARTS LIST ................................ 27
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
This appliance is
classified as a CLASS 1
LASER product. This
label is located on the
rear exterior.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
SCD-XE597
SECTION 1
SERVICING NOTES
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH
TURNS OFF
MODEL IDENTIFICATION
– Back Panel –
Insert a tapering driver into the aperture of the unit bottom, and turn
in the direction of arrow.
Use a flat (-) head screwdriver to open the disc tray by manual
operation. (Flat head screwdriver with nominal blade length of
3mm.)
* To close the disc table, turn the driver in the reverse direction.
Parts No.
tapering driver
MODEL
AEP Model
UK Model
Part No.
4-255-245-0[ ]
4-255-245-1[ ]
3
SCD-XE597
SECTION 2
GENERAL
This section is extracted
from instruction manual.
Front Panel
1
2
3
4
5
6
7
8
l
qh
qg
qf qd
qs
qa q;
9
A POWER switch (9)
J X button (9)
B SA-CD/CD button (5, 9)
Each time you press the button while playing back
a hybrid disc, the layer to be played back switches
between the SA-CD layer and the CD layer.
K H button (9, 12, 13, 14)
C PLAY MODE button (13, 14)
Press to select the play mode.
D Disc tray (9)
E MULTI CHANNEL DECODING indicator
Turns on when you turn on the player, or when the
Multi-channel Super Audio CD is loaded and
select the multi-channel playback area by pressing
MULTI/2CH.
F A button (9)
G x button (9, 14)
H m/M buttons (12)
I l AMS L dial
(AMS: Automatic Music Sensor) (8, 9, 10,
12, 14, 15, 16, 18)
4
L
L Display window (10)
M Remote sensor
(6)
N TIME/TEXT button (11)
Each time you press the button, the playing time of
the track, the remaining time of the disc, or TEXT
information appears in the display.
O MULTI/2CH button (5, 9)
Press to select the playback area when a disc with
the 2 channel area and the multi-channel area
(page 5) is loaded.
P MENU button (8, 9, 10, 12, 15, 16, 18)
Press to enter the menu.
Press to exit from the menu and return to the
normal display.
SCD-XE597
A CD1/2 (command mode) switch (8)
Select the command mode.
Remote
1
qg
2
qf
3
qd
4
qs
5
B CONTINUE button (13, 14)
Press to resume Continuous Play from Shuffle Play
or Program Play.
SHUFFLE button (13)
PROGRAM button (14)
C TIME/TEXT button (11)
Each time you press the button, the playing time of
the track, the remaining time of the disc, or TEXT
information appears in the display.
D DISPLAY MODE button (12)
Press to turn the display information off or on.
E m/M buttons (12)
F CLEAR button (14)
Press to delete a programed track number.
G LEVEL ADJ button (17)
Press to adjust the output level balance for the
Multi-channel management function (page 15).
qa
H ENTER button (8, 9, 10, 12, 14, 15, 17, 18)
q;
9
6
7
8
I CHECK button (14)
Press to check the programed order.
J REPEAT button (13)
K H button (9, 12, 13, 14)
X button (9)
x button (9, 14)
L AMS ./> buttons
(AMS: Automatic Music Sensor) (8, 9, 10,
12, 14, 15, 17, 18)
M SA-CD/CD button (5, 9)
Each time you press the button while playing back
a hybrid disc, the layer to be played back switches
between the SA-CD layer and the CD layer.
N MULTI/2CH button (5, 9)
Press to select the playback area when a disc with
the 2 channel area and the multi-channel area
(page 5) is loaded.
O DISC SKIP +/– buttons*
Press to select the disc.
*This button cannot be used in this player.
5
SCD-XE597
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
• The dotted square with arrow (
) prompts you to move to the next job when all of the works within the dotted square (
completed.
3-1. DISASSEMBLY FLOW
SET
3-2.COVER
(Page 6)
3-4.LOADING PANEL
(Page 7)
3-3.MAIN BOARD
(Page 7)
3-7.CD MECHANISM DECK
(CDM66D-DVBU50)
(Page 9)
3-5. FRONT PANEL SECTION
(Page 8)
3-8.BASE UNIT (DVBU50)
(Page 9)
3-6.KEY BOARD,
DISPLAY BOARD
(Page 8)
3-9. RF BOARD,
PICK-UP UNIT (DBU-3)
(Page 10)
3-10. BELT (LD), LOADING BOARD,
MOTOR (L) ASSY
(Page 10)
Note: Follow the disassembly procedure in the numerical order given.
3-2. COVER
1 two screws
(case 3)
cover
3 screw
(+BVTP 3 × 8)
4
5
4
2 two screws
(case 3)
6
) are
SCD-XE597
3-3. MAIN BOARD
3 wire (flat type)
(13 core) (CN703)
4 wire (flat type)
(31 core) (CN702)
6 screw
(+BVTP 3 × 8)
2 connector
(8p) (CN901)
8 MAIN board
5 three screws
(+BVTP 3 × 8)
7 PWB holder
1 connector
(5p) (CN151)
3-4. LOADING PANEL
1
3 two claws
tapering driver
4 loading panel
2
7
SCD-XE597
3-5. FRONT PANEL SECTION
3 connector (CN101)
2 connector (CN891)
1 wire (flat type)
(13 core) (CN703)
4 claw
5 claw
7 front panel section
6 three screws
(+BVTP 3 × 8)
3-6. KEY BOARD, DISPLAY BOARD
6 LED board
8 connector (CN813)
3 bracket
9 KEY board
1 knob (AMS)
7 three screws
(+BVTP 2.6 × 8)
5 connector (CN814)
4 two screws
(+BVTP 2.6 × 8)
q; seven screws
(+BVTP 2.6 × 8)
2 two screws
(+BVTP 2.6 × 8)
qa DISPLAY board
8
SCD-XE597
3-7. CD MECHANISM DECK (CDM66D-DVBU50)
3 three screws
(+BVTP 3 × 8)
4 CD mechanism deck
(CDM66D-DVBU50)
1 wire (flat type)
(31 core) (CN702)
2 connector
(5p) (CN151)
3-8. BASE UNIT (DVBU50)
3 screw (DIA. 12), floating
DVBU50
1 Turn the cam to the direction of
arrow (counter clock wise) by
tapering driver.
4 Remove the Base unit
(DVBU50) to the direction
of arrow.
2 Take off the tray.
9
SCD-XE597
3-9. RF BOARD, PICK-UP UNIT (DBU-3)
7 three screws
(step screw (M))
8 pick-up unit (DBU-3)
holder (66D)
2 hook
4 CN001
5 wire (flat type) (CN002)
6 RF board
3 flexible board (CN003)
1 two screws
(BTTP M2.6)
3-10. BELT (LD), LOADING BOARD, MOTOR (L) ASSY
6 belt (LD)
5 gear (LD)
7 two screws
(B 2.6 × 4)
1 claw
3
0 motor (L) assy
2 claw
9 LOADING board
4 tray (66)
10
8 Removal the solders.
SCD-XE597
SECTION 4
DIAGRAMS
• Waveforms
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
W : indicates side identified with part number.
•
f
: internal component.
•
: Pattern from the side which enables seeing.
Note Schematic Diagrams.
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
f : internal component.
• C : panel designation.
Caution:
Pattern face side: Parts on the pattern face side seen from
(Side B)
the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(Side A)
the parts face are indicated.
– MAIN Board –
– DISPLAY Board –
1 IC001 tl SIGO (CD)
2 IC706 uk DSPHREFO
5 IC801 5 IC
200 ns/DIV
These are omitted.
B E
40 ns/DIV
3 IC706 <z./
40 ns/DIV
RF IN (SACD)
1.4 Vp-p
3.3 Vp-p
88.6 ns
PT board
RF board
KEY board
LED board
LOADING board
1.4 Vp-p
200 ns
354 ns
4 IC320 2,4,6,q;,qs
• Circuit Boards Location
POWER SW board
1.4 Vp-p
1 IC001 tl SIGO (SACD)
• A : B+ Line.
• B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark: SACD PLAY
(
): CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J
: CD
c
: CD DIGITAL OUT (OPTICAL)
C
3.5 Vp-p
3.5 Vp-p
Note: The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
• Indication of transistor.
Q
– RF Board –
MAIN board
DISPLAY board
SCD-XE597
11
11
SCD-XE597
4-1. BLOCK DIAGRAMS
OPTICAL PICK-UP BLOCK
6,14
VCC
A5V
VC
5
3
9
1 RFIP
A
14 A
B
13 B
2
C
1
7
D
12 C
11 D
E
15 E
F
10
16 F
Q001
17
LD
DRIVE
DVDLD
25 DVDLD
SIGO 59
190 RFAC
15
12
LD
DRIVE
CDLD
SW
26 CDLD
2 PD
200 TEI
CDBCK 95
FE 42
201 FEI
CDLRCK 94
MIRR 33
TZC 37
DSAR 84
4
PDATA VOUTL 9
231 MIRR
DSALS 85
3
PBCK
230 TZC
DSARS 86
5
PLRCK
DSAC 89
1
DSDL
2
DSDR
DFT 38
229 DFCTI
SRD 45
245 SSI
SWD 46
246 SSO
SCLK 47
247 SCK
SDEN 48
244 SCS
LDON 27
234 INLIM
GND
DSPHREFO 78
LIMIT
IN
SWITCH
IC712
MOTOR/COIL DRIVER
FCS+
FOCUS
COIL
IC260
DAC
37 DO1+
215 FDOP
IC705
MASTER CONTROL
MCKI 3
A0-8
21-29
D0-7
11-18
XINT 32
92 XINT0
XCS 33
87 XCS
73 XWAIT
71 XWR
XWR 35
TR+
TRACKING
COIL
36 DO1-
IN1- 1
216 FDON
35 DO2+
IN2+ 3
213 TDOP
TR-
34 DO2-
SLB+
SLB-
214 TDON
IN2- 4
32 DO3+
31 DO330 DO4+
C
OUT 6
IC702
EEPROM
IN3+ 6
220 SLDB
IN3- 7
IN4+ 9
SLA-
29 DO428 DO5+
IN5+ 12
206 VCO
M
SPM+
27 DO5-
47 OPIN1+
221 MDS0
MD0-15
222 MDP0
XRAS,
XCAS,
XMWR,
MCKE,
MMCK,
LDQM,
UDQM
IN5- 13
204 SP RV
OPOUT1 45
235 FGMODE
LOADP
14 ZEROR
MZL 95
13 ZEROL
R MUTE
Q305
R MUTE 97
M/2 100
IC230
DAC
24 DO6-
12
OUT
LOAD S1 27
16
1
DSDL
2
DSDR
J351(2/3)
7
SL
SR
2
SR
1
17 MS
MUTE
Q531,532
16 MC
15 MD
IC200
DAC
7
PBCK
5
PLRCK VOUTR 10
1
DSDL
2
DSDR
RAS,
CAS,
WE,
CKE,
CLK,
LDQM,
UDQM
EXTAL 65
IC801
DISPLAY CONTROLLER
RESET 6
17 SIRCS
SO1 9
SI1 8
3
ANI1-3
6
J351(3/3)
7
CENTER
SW
SW
MUTE
IC460(2/2) Q462,463
AMP
2
1
18 PSCK
X321
11.2896MHz
5
6
9
D509
RM 1
CENTER
19 DSCK
MUTE5 21
IC802
SIRCS
VOUTL 9
IC460(1/2)
AMP
20 DBCK
35 DRV ON
ACK 12
SCK1 7
REQ 15
17 MS
8
3
4
11
10
13
12
1
2
15 MD
VF2
VFL
IC703
+1.8V REG
+1.8V
3
IC920
+3.3V REG
+3.3V
1
3
VFL REG
Q971
RECT
D921-924
1
84 IFSI
IC950
+5V REG
83 IFSO
91 XIFINT
85 IFSC
+5V
3
+12V
RECT
D931-934
1
96 XIFCS
IC985
AU+ REG
MUTE
11 P23
AU+
D801
SCD-XE597
12
12
T101
POWER TRANSFORMER
VF1
IC320
INVERTER
36 SP ON
MUTE
Q562,563
16 MC
INDICATION TUBE
FL801
LED
Q826
6
MUTE
IC430(2/2) Q431,432
AMP
3
MUTE12 19
: CD DIGITAL OUT (OPTICAL)
PLRCK VOUTR 10
SL
MUTE
Q301
18 PSCK
30 TRAY IN
: CD
5
DQ0-15
FWD 16
KEY
VOUTL 9
19 DSCK
PS 39
• Signal Path
PBCK
20 DBCK
EPR/B,
XEPCS,
XEWC,
EEPSO,
EEPSI,
EEPSCK
33 TRAY OUT
S841-845,
S851,855,
S861-865
3
A0-10,BA
REV 17
MUTE34 20
IC430(1/2)
AMP
IN
LOAD S0 25
M
LOADN
L MUTE
Q303
L MUTE 98
72 XWRST
59 XRST
MUTE
Q501,502
15 MD
MZR 94
38 XLDON
25 DO6+
1
16 MC
IC708
16M SDRAM
MA0-10,BA
2
74 SMUTE
219 SLDA
IN4- 10
70 XRD
R
MUTE
IC400(2/2) Q401,402
AMP
17 MS
52 JIT
JIT 226
SMUTE 61
46 OPIN1-
LOADING
MOTOR
S701
RESET
203 SEI
M
SPMSPINDLE
MOTOR
IC701
RESET
M
SLA+
SLED A
MOTOR
XRST 37
5
OUT2 5
SLED B
MOTOR
D511
L
VOUTR 10
18 PSCK
13,15-22 CA0-8 SLATR DAC 3
SCLK DAC 2
4-11 CD0-7
SDATA DAC 1
8
J351(1/3)
7
19 DSCK
9
XRD 36
FCS-
6
20 DBCK
XWAIT 34
IN1+ 48
IC400(1/2)
AMP
DSAL 83
202 PI
PI 36
VCI 39
4
DIGITAL
OUT
OPTICAL
1
PCMD1 96
TE 41
DSASW 90
24 LDSELO
PD
VR
D OUT
DOUT958 100
Q002
19
IC330
OPTICAL OUT
19 VC
RF
8
IC706
DIGITAL SERVO,
DIGITAL SIGNAL PROCESSOR
IC001
RF AMP
3
1
MUTE REG
Q961
RECT
D960,961
RECT
D936,937
D971
S891
POWER
SCD-XE597
4-2. PRINTED WIRING BOARD — RF SECTION —
• See page 11 for Circuit Boards Location.
:Uses unleaded solder.
OPTICAL
PICK-UP
BLOCK
(DBU-3)
A
IC001
MAIN BOARD
CN702
(Page 15)
M901
SPINDLE MOTOR
M902
SLED MOTOR
• Semiconductor
Location
SCD-XE597
13
13
Ref. No.
D001
D004
Location
C-9
D-9
IC001
C-9
Q001
Q002
D-5
D-5
SCD-XE597
• See page 11 for Waveforms.
4-3. SCHEMATIC DIAGRAM — RF SECTION —
C011
0.01
C001
0.01
C004
22
6.3V
C035 0.1
C044
10
16V
R037 12k
C033 0.001
C031 0.1
C028 0.1
C025 0.1
C022 0.1
R002 100
C032 0.1
C027 0.01
C002
0.01
C039
0.01
CN001
24P
JL003
JL004
R045
220
JL005
R009
820
C016
JL006
C015
0.0047
JW001
0.0047
JW002
JL007
C019
560p
JL008
JL009
JL011
JL012
R003
100
C005
0.0022
C006
0.0022
C007
0.0022
CN002
31PIN
C043
0.1
IC001
SP3726A
JL010
R004
C047
0.1
C048
0.01
0
C008 0.0022
JL013
R052 0
JL014
R053
JL015
0
R054 0
R055 0
JL016
JW003
JL017
C046
JW004
JL018
JL020
R006
27k
JL021
JL022
R018
10k
C026
0.01
R008
33
R010
47k
C017
100
6.3V
R011
100
C034
0.022
R023
33
R020
33
JL002
R013
10k
Q001
2SB1132-T100-QR
R025
47k
Q002
2SB1132-T100-QR
CN003
9P
JL025
JL026
L002
L001
JL024
D001
1SS355TE-17
C009
10
16V
C018
0.001
D004
1SS355TE-17
C024
0.001
C021
10
16V
JL027
JL028
JL029
JL030
JL031
SCD-XE597
14
14
C023
100 6.3V
R007
33
JL001
C038 0.047
C036 0.047
JL023
R029
100
C040
150p
R038
2.2M
R005
100k
JL019
0.01
SCD-XE597
• See page 11 for Circuit Boards Location.
4-4. PRINTED WIRING BOARD — MAIN SECTION —
:Uses unleaded solder.
DISPLAY BOARD
CN801
(Page 20)
B
PT BOARD
CN102
(Page 20)
IC950
IC985
C
IC200
IC400
L
FRONT
IC920
R
IC230
IC702
L
IC430
SURR
R
IC320
IC260
IC701
CENTER
IC460
IC705
SUB WOOFER
IC712
IC706
IC703
IC330
IC708
A
LOADING BOARD
RF BOARD
CN002
(Page 13)
CN151
5
S272
LOADING
IN
S271
LOADING
OUT
M
M151
(LOADING)
1
21
1-645-721-
• Semiconductor Location
Ref. No.
D321
D509
D511
D921
D922
D923
D924
D931
D932
D933
Location
E-4
G-6
E-6
C-12
C-12
C-12
C-12
C-12
C-12
C-12
Ref. No.
D934
D936
D937
D960
D961
D963
D971
D972
D973
Location
C-12
B-12
C-10
B-4
C-8
B-4
D-11
D-8
D-8
Ref. No.
IC200
IC230
IC260
IC320
IC330
IC400
IC430
IC460
IC701
IC702
Location
C-4
D-4
E-4
S-5
G-16
D-15
D-15
E-15
E-11
D-12
Ref. No.
IC703
IC705
IC706
IC708
IC712
IC920
IC950
IC985
Location
F-12
E-5
G-3
H-15
F-7
D-13
B-13
B-14
Q301
C-3
Ref. No.
Q303
Q305
Q401
Q402
Q431
Q432
Q462
Q463
Q501
Q502
Location
C-3
C-3
C-15
D-2
D-15
E-2
E-15
E-2
C-15
C-2
Ref. No.
Q531
Q532
Q562
Q563
Q961
Q971
Location
D-15
D-2
E-15
E-2
B-3
D-7
SCD-XE597
15
15
(21)
5.1CH OUT
ANALOG
SCD-XE597
• See page 11 for Waveforms.
C706
0.1
CL771
CL847
CL848
CL770
CL846
C714
220
4V
C762 0.1
CL844
0.1
C761
CL845
0.1
C759
CL842
CL841
CL838
CL839
CL840
CL836
CL843
C757
0.1
C755
0.1
CL837
47k
C753
R783
10k
CL835
SL798
C751
100p
R781 1k
CL723
C745
0.1
0.1
C746
0.1
C733
0.047
0.1
CL724
C788
STP702
XX
C749
CN702
31P
0.1
C754
220
4V
C789
0.1
R782
4-5. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) —
IC703
RB604
4.7k
SL897
C771
0.1
CL877
SL896
CL876
C736 0.1
CL721
CL875
CL874
TP713
RB603
470
SL774
C731
0.0047
C730
0.0047
C723
1
C726
0.001
C722
0.1
C727
0.0047
SL773
C729
0.001
R752
0
RB602
1k
SL772
CL804
SL771
CL803
CL830
CL802
CL829
CL801
CL828
CL800
CL754
CL799
CL753
CL798
CL752
CL797
C770
0.1
C769
0.1
CL796
CL751
0.1
C743
SL778
CL795
SL777
CL794
SL776
CL793
SL775
C742 0.1
CL792
CL791
C768
0.1
CL790
CL834
CL833
CL832
CL831
IC706
CXD2754Q
256-QFP(0.4)
0.1
C741
RB617
470
CL789
CL788
CL787
CL873
CL872
CL767
C734
0.1
CL871
SL770
0.1
C740
CL870
CL786
CL827
C767
0.1
CL826
RB616
470
CL869
CL825
C739 0.1
C766
0.1
CL867
CL866
CL824
CL823
CL766
CL865
CL765
CL864
CL764
CL763
CL785
CL762
CL784
C765
0.1
C738 0.1
SL871
CL822
CL821
SL875
CL820
CL782
CL819
SL872
CL776
CL755
CL775
TP729
CL861
CL862
CL863
CL860
CL859
CL856
CL857
CL858
C760
CL854
CL855
CL852
CL853
CL850
CL851
SL856
SL845
TP715
SL848
CL849
SL840
SL841
SL843
SL839
C758 0.1
SL837
0.1
C756
TP714
SL800
C744
1
CL773
CL777
CL756
TP730
XX
SCD-XE597
16
16
CL774
CL778
CL757
CL772
CL779
CL758
C763 0.1
CL759
0.1
CL780
C752 0.1
CL781
CL760
C750 1
CL761
CL737
RB613
10k
0.1
SL799
C737
C764
0.1
RB615
470
SCD-XE597
• See page 22 for IC Block Diagrams.
4-6. SCHEMATIC DIAGRAM — MAIN SECTION (2/4) —
CN703
13P
FB703
0UH
FB710
0UH
RB612
10k
RB601
10k
RB607
10k
RB606
10k
FL606
0UH
C715
CL883
CL880
CL881
CL882
CL748
CL879
CL746
CL740
CL878
C721 0.1
C713
100 16V
0.1
R731
10k
R708
100
CL734
CN701
9P
CL769
CL768
C712
0.1
CL731
C711
0.1
C748
0.1
CL891
IC705
HD6432238RN51TEV
CL890
CL889
CL888
D511
DAP202UT106
CL733
CL732
C704 0.1
STP703
XX
R701 1k
S701 RESET
CL743
CL708
C702 1
CL730
C705
0.1
C701
R703 10k
0.1
R702 10k
RB611
10k
C703
0.1
IC702
BR9040F-WE2
CL722
RB605
10k
CL726
SCD-XE597
17
17
SL790
SL792
SL759
SL757
SL753
SL751
SL749
CL747
SL746
CL742
CL745
CL741
SL742
CL893
CL894
CL739
CL892
CL738
SL732
CL725
SL730
R707
1k
CL736
CL709
CL710
CL735
IC701
M51957BFP-600C
SCD-XE597
4-7. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) —
CL712
CL727
C709
220
4V
CL713
C716
100
16V
CL711
STP701
XX
CL728
CL729
R861
270k
C815
0.015
C814
0.22
C793
0.1
R878
470k
C825
0.0015
R858
120k
R877
470k
R860
680k
CL809
C796
100
16V
CL808
R831
10k
R840
CL807
R852
100k
100k
D509
DAP202UT106
C800 0.1
CN705
5P
RB610
47k
CL818
R897
470k
C832
0.0047
CL812
CL813
RB609
10k
R899
220k
C817
0.001
IC712
FAN8035L
R870
33k
C772 0.1
R869
56k
SL891
C816
0.001
SL898
C775
0.1
R866
33k
R865
56k
R889
0
CL805
C776
0.1
R876
82k
R791 47
CL806
R895
56k
SL894
R874
33k
C780
0.1
C794
0.1
C795
100
16V
R846
56k
C787
0.1
R872
10k
IC708
MSM56V16160F-
R871
10k
R804
330
C819
1
C781
0.1
C785
220
4V
C783
100
16V
8TK7R1
TP733
XX
R880
100k
C804 0.1
R820 150k
R819
150k
SCD-XE597
18
18
R853
56k
C813
0.033
C829 0.068
R893
120k
M151
15k
CN151
5P
R888
SL892
R857
33k
C809
0.033
C779
0.1
CL814
S272
C820
220p
SL893
C778
0.1
S271
R894
56k
R886 82k
CL815
C782
0.1
C828
0.068
SL895
R806 10
C822
220p
C777
10p
R885
15k
C821
100p
R892
120k
C830
100p
SCD-XE597
4-8. SCHEMATIC DIAGRAM — MAIN SECTION (4/4) —
• See page 11 for Waveforms.
IC985
BA12FP-E2
C934
470
16V
C933
0.1
C953
0.1
D960
DAN202UT106
D936
C932 1SR154-400TE25
470
35V
D937
1SR154-400TE25
C954
470
10V
C935
1000
16V
D933
1SR154-400TE25
D931
1SR154-400TE25
C901
0.01
IC950
BA50BC0FPE2
L320
XX
C324
1
R330 22
22
Q961
DTC143TKAT146
D932
1SR154-400TE25
C961
10
50V
R323
1k
R961
R962
1k
D934
1SR154-400TE25
D961
DAN202UT106
C910 0.001
R963
1k
ETP910
EARTH PLATE
1k
R328
C921
10000
10V
C924
470
10V
C931
10000
16V
D963
UDZSTE -173.0B
D923
1SR154-400TE25
D921
1SR154-400TE25
R322
0
IC320
SN74LVU04APWR
C920 0.01
D922
1SR154-400TE25
C322
15p
C321
15p
CN901
8P
C962 0.1
R321
1M
Q305
UN5116-TX
IC920
BA33BC0T
C281
2200p
X321
11.2896M
D924
1SR154-400TE25
D971
1SR154-400TE25
R324
100
Q303
UN5116-TX
CL301
C302
0.1
C212
10
50V
Q301
UN5116-TX
RB301
4.7k
Q971
2SB1260
SL216
C971
47
63V
SL217
R326 22
SL220
C406
47 25V
IC200
DSD1751DBQR
C405
0.1
C504 1
C208 1
C206 1
SL201
C402
0.001
RB402
6.8k
C403
150p
C362
0.1
R407
100k
R411
R409
220
Q401
2SC3624AT1L15L16
C972
10
50V
R975
33k
R976
100
R977
100
R979
10k
R978
22k
C973
22
16V
100
Q402
2SC3624A-T
1L15L16
R404
3.3k
R504
3.3k
C502
0.001
R973
3.3k
D972
UDZSTE-17-33B
R408
330
C201
1000
6.3V
R972
10k
R971
10k
IC400(2/2)
NJM4565M(T
E2)
C404
1
0.01
CL302
RB302
220k
SL215
C970
C305
0.1
C303
0.1
D973
UDZSTE-179.1B
D321
1SS357-TPH3
C923 0.1
C325
100
6.3V
RB410
2.2k
R507
100k
C503
150p
Q501
2SC3624AT1L15L16
RB502
6.8k
IC400(1/2)
NJM4565M(T
E2)
CL245
C202
47
6.3V
IC430(2/2)
NJM4565M(T
E2)
C534 1
C238 1
C236 1
C436
47
25V
C433 150p
33k
C434 1
R202
SL231
CL275
R508
330
R511
100
0UH
R201 10k
CL274
J351
6P
R509
220
C506
47 25V
FB201
IC230
DSD1751DBQR
C505
0.1
C432
0.001
RB432
6.8k
C532
0.001
RB532
6.8k
R439
220
Q431
2SC3624AT1L15L16
C435
0.1
C364
0.1
C533
150p
C272
10
50V
R438
330
Q432
2SC3624AT1L15L16
R434
3.3k
R437
100k
R534
3.3k
R537
100k
Q532
2SC3624AT1L15L16
C535
0.1
IC430(1/2)
NJM4565M(T
E2)
IC460(2/2)
NJM4565M(T
E2)
C463 150p
C464 1
IC260
DSD1751DBQR
C462
0.001
SL261
C562
0.001
CL868
C366
0.1
C466
47
25V
CL201
C266 C268
1
1
C351
0.1
CL202
Q531
2SC3624AT1L15L16
R468
330
C331
0.1
R469
220
C465
0.1
RB462
6.8k
RB562
6.8k
R464
3.3k
R467
100k
R564
3.3k
R567
100k
Q463
2SC3624A-T
1L15L16
Q462
2SC3624AT1L15L16
Q563
2SC3624A-T
1L15L16
SL262
C564
1
RB442
2.2k
R539
220
R538
330
C536
47
25V
RB441
2.2k
C565
0.1
C563
150p
IC460(1/2)
NJM4565M(T
E2)
C566
47
25V
Q562
2SC3624AT1L15L16
R569
220
R568
330
SCD-XE597
19
19
IC330
IC TOTX141L
CL244
C242
10
50V
Q502
2SC3624A-T
1L15L16
SCD-XE597
4-9. PRINTED WIRING BOARD — DISPLAY SECTION —
B
• See page 11 for Circuit Boards Location.
:Uses unleaded solder.
MAIN BOARD
CN703
(Page 15)
MULTI CHANNEL DECODING
M
m
A
IC801
. AWS >
PUSH ENTER
x
X
H
IC802
C
TIME/TEXT
PLAY MODE
MULTI/2CH
SA-SD/CD
MENU
MAIN BOARD
CN901
(Page 15)
S891
AC IN
• Semiconductor
Location
SCD-XE597
20
20
Ref. No.
Location
D801
B-12
IC801
IC802
E-12
E-16
Q821
Q822
Q823
Q824
Q825
Q826
E-14
E-10
E-10
E-10
D-9
E-8
SCD-XE597
4-10. SCHEMATIC DIAGRAM — DISPLAY SECTION —
• See page 11 for Waveforms.
C819
0.01
CN805
2P
R832
100
R862
2.2k
R861
1k
C831
47
6.3V
C832
0.01
S861
S862
S863
S864
S865
R841
1k
TP126
CN813
2P
IC802
NJL73H400A
R831
47
R826
10k
TP26
R842
2.2k
R820
10k
S841
S842
S843
R844
4.7k
R845
10k
C816
0.001
100k
0.01
S845
R853
2.2k
R854
4.7k
S851
S855
ENCORDER
Q826
2SC3624AT1L15L16
C812
0.001
R858
82
CN804
2P
C813
0.001
RB802
100k
R852
2.2k
S844
C817
C803 0.1
R828
100k
C818 0.01
R851
1k
R827
R843
2.2k
R819
10k
C804
0.1
R817 10k
R863
2.2k
R818 10k
R864
4.7k
C811
0.001
IC801
8BT-A
R856
10k
RB801
100k
FB801
FB
R857
10k
TP5
X801
5MHz
R805
10k
C802
0.1
C805
0.1
C806
0.1
C801
100
6.3V
Q824
DTC114EKA
-T146
CN801
13P
Q821
DTC114EKA-T146
Q825
DTC114EKA
-T146
Q822
DTC114EKA-T146
R821
100k
R822
100k
Q823
DTC114EKA
-T146
R823
100k
C822
0.001
C823
0.001
R824
100k
C824
0.001
R825
100k
C825
0.001
C821
0.001
C827
0.1
C829
0.1
FL801
T101
D801
SEL5E20C-STP15
BLUE
S891
C891
0.0022
250V
C101
0.0022
250V
CN101
2P
CN892
2P
CN891
2P
CN102
8P
SCD-XE597
21
21
C833
0.1
R834
10k
CN814
2P
SCD-XE597
SECTION 5
TEST MODE
• IC Block Diagrams
– MAIN Board –
VCC
OUT
C
WC
GND
DO
DI
IC702 BR9040F-WF2
NC
IC701 M51957BFP-600C
8
7
6
5
8
7
6
5
3
4
IN
NC
GND
8bit
2
16bit
HIGH VOLTAGE
GENERATOR
R/W
AMP
POWER
SUPPLY
VOLTAGE
DETECTOR
3. Sircs Receive Check
Procedure:
1. The message “SIRCS CHECK” is displayed on the fluorecent
indicator tube.
2. With the machine in the status that is set in step 2, press any
on the remote commander. The machine enters the key check
standby state. (When the H key or the x key is pressed,
the reception check is canceled.)
COMMAND DECODE
CONTROL CLOCK
GENERATION
1
2
3
4
VCC
CS
SK
DATA
REGISTER
R/B
ADDRESS
BUFFER
WRITE
DISABLE
16bit
8bit
1.25V
1
NC
ADDRESS
DECODER
2. FL Tube Grid, Segments Check
Procedure:
1. Grid of all segments lights up sequentially starting from 1G to
16G.
2. The vertical line (total 5 lines) of all grids lights up sequentially
in the range of 5G to 16 G starting from the left.
3. The horizontal line of (total 7 lines) of all grids lights up
sequentially in the range of 5G to 16G starting from the top.
COMMAND
REGISTER
4096bit
EEPROM ARRAY
–
+
1. Setting Methed of Test Mode
Press three buttons m , [PUSH ENTER] and [POWER] simultaneously, The test mode becomes active. Then all segments of the
fluorecent indicator tube are turned on.
SCD-XE597
22
22
4. Key Check
Procedure:
1. In the key check mode, the fluorecent indicator displays “KEY
CHECK**”. Each time a button is pressed, “**” value.
However, once a button is pressed, it is no longer taken into
account.
2. To exit from this mode, the message “JOG CHECK” is
displayed.
5. Jog Check
Procedure:
1. After the key check is completed, turn JOG clockwise to turn
on the calendar segments sequentially. When the segment “15”
is confirmed, turn JOG counter-clockwise that turns off the
calendar segment. When the segment “1” is confirmed, this is
the end of check.
6. Releasing Meted of Test Mode
1. After all the checks are completed, confirm to see that the
display “TEST-END” appears. The message indicates that
the check is ended normally.
2. Press the [POWER] button to turn off the main power and
disconnect the power plug from the wall outlet.
SCD-XE597
Ver. 1.3
SECTION 6
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
6-1.
•
•
The mechanical parts with no reference
number in the exploded views are not supplied.
Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet’s Color
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
MAIN SECTION
3
2
#1
11
2
4
#1
6
CD mechanism deck
(CDM66D-DVBU50)
8
5
not supplied
10
7
#1
front panel section
not supplied
#1
9
1
#1
Ref. No.
Part No.
Description
Remark
1
1
1
2
2
4-255-243-01
4-255-243-11
4-255-243-31
3-363-099-02
3-363-099-11
PANEL LOADING (BLACK)
PANEL LOADING (SILVER)
PANEL LOADING (SILVER: Hair-line Finish)
SCREW (CASE 3 TP2) (AEP: BLACK)
SCREW (CASE 3 TP2)
(AEP: SILVER, SILVER: for Hair-line Finish)
2
3
3
3
4-227-843-21
2-660-400-31
4-232-149-31
4-232-580-31
SCREW (TP), FLAT HEAD (UK)
CASE (SILVER, SILVER: for Hair-line Finish)
CASE (408226) (BLACK)
CASE (408226)
Ref. No.
Part No.
Description
4
* 5
06
* 7
8
1-862-181-11
3-703-244-00
1-777-071-43
4-954-051-51
A-4752-595-A
PT BOARD
BUSHING (2104), CORD
CORD, POWER
HOLDER, PC BOARD
MAIN BOARD, COMPLETE
9
0 10
11
#1
X-2022-049-1
1-443-287-11
3-077-331-01
7-685-646-79
FOOT ASSY
TRANSFORMER, POWER
+BV3 (3-CR)
SCREW +BVTP 3X8 TYPE2 IT-3
Remark
23
SCD-XE597
Ver. 1.3
6-2. FRONT PANEL SECTION
56
not
supplied
56
56
not
supplied
57
54
56
56
55
56
53
58
not
supplied
56
59
not
supplied
60
52
51
Ref. No.
51
51
51
Part No.
Description
Remark
52
53
4-232-622-01 KNOB (AMS) (BLACK)
4-232-622-31 KNOB (AMS) (SILVER)
4-232-622-41 KNOB (AMS)
(SILVER: SILVER: for Hair-line Finish)
3-354-981-11 SPRING (SUS), RING
X-2103-118-1 PANEL, FRONT ASSY (SILVER: Hair-line Finish)
53
53
54
X-4956-440-1 PANEL, FRONT ASSY (BLACK)
X-4956-441-1 PANEL, FRONT ASSY (SILVER)
4-255-244-01 BUTTON, POWER (BLACK)
24
Ref. No.
Part No.
Description
Remark
54
54
55
56
57
4-255-244-11
4-255-244-31
1-862-182-11
3-087-053-01
1-862-179-11
BUTTON, POWER (SILVER)
BUTTON, POWER (SILVER: for Hair-line Finish)
POWER SW BOARD
+BVTP2.6 (3CR)
KEY BOARD
58
59
60
1-828-333-11 WIRE (FLAT TYPE) (13 CORE)
A-4752-665-A DISPLAY BOARD, COMPLETE
4-977-358-01 CUSHION
SCD-XE597
6-3.
CD MECHANISM DECK
not supplied
208
not supplied
207
#3
209
206
205
204
210
DVBU50
M901
203
201
202
Ref. No.
Part No.
Description
201
202
203
204
205
4-227-899-01
1-645-721-11
4-231-530-12
4-232-712-05
4-232-710-01
SCREW (DIA.12), FLOATING
LOADING BOARD
TRAY (66)
CAM (66)
PULLEY (LD)
206
4-232-713-01 BELT (LD)
Remark
Ref. No.
Part No.
Description
207
208
209
210
M901
4-232-711-01
3-053-844-01
4-231-529-01
4-232-682-01
A-4604-363-A
GEAR (LD)
YOKE
CHASSIS (66)
CUSHION (66)
MOTOR (L) ASSY (LOADING)
#3
7-621-775-10 SCREW +B 2.6X4
Remark
25
SCD-XE597
6-4.
BASE UNIT (DVBU50)
257
257
256
255
256
257
256
254
258
253
252
251
Ref. No.
251
252
253
254
Part No.
Description
4-218-253-52
A-4750-527-A
1-829-172-11
4-240-953-05
SCREW (M2.6), +BTTP
RF BOARD, COMPLETE
WIRE (FLAT TYPE) (31 CORE)
HOLDER (66D)
Remark
Ref. No.
Part No.
Description
0 255
256
257
258
A-4713-410-A
3-053-847-31
4-981-923-01
1-824-106-12
PICK-UP UNIT (DBU-3)
INSULATOR
SCREW (M), STEP
CABLE, FLEXIBLE FLAT (24 CORE)
Remark
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
26
SCD-XE597
SECTION 7
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• CAPACITORS
uF: µF
Ref. No.
Part No.
•
•
•
RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
COILS
uH: µH
SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
Description
Remark
A-4752-665-A DISPLAY BOARD, COMPLETE
************************
4-949-935-41 CUSHION (FL)
< CAPACITOR >
C801
C802
C803
C804
C805
1-124-584-00
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.1uF
0.1uF
0.1uF
20%
C806
C811
C812
C813
C816
1-165-319-11
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
50V
50V
50V
50V
50V
C817
C818
C819
C821
C822
1-162-970-11
1-162-970-11
1-162-970-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
25V
25V
25V
50V
50V
C823
C824
C825
C827
C829
1-162-964-11
1-162-964-11
1-162-964-11
1-165-319-11
1-165-319-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.1uF
0.1uF
10%
10%
10%
50V
50V
50V
50V
50V
C831
C832
1-124-589-11 ELECT
1-162-970-11 CERAMIC CHIP
47uF
0.01uF
20%
10%
6.3V
25V
< CONNECTOR >
CN801
1-779-281-11 CONNECTOR, FFC (LIF (NON-ZIF)) 13P
6.3V
25V
25V
25V
25V
Ref. No.
DISPLAY
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
•
Accessories are given in the last of this parts
list.
Part No.
Description
Q822
Q823
Q824
Q825
8-729-027-43
8-729-027-43
8-729-027-43
8-729-027-43
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q826
8-729-141-73 TRANSISTOR
Remark
DTC114EKA-T146
DTC114EKA-T146
DTC114EKA-T146
DTC114EKA-T146
2SC3624A-T1L15L16
< RESISTOR >
R805
R817
R818
R819
R820
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R821
R822
R823
R824
R825
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R826
R827
R828
R831
R832
1-216-833-11
1-216-845-11
1-216-845-11
1-216-805-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
100K
47
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R841
R842
R843
R844
R845
1-216-821-11
1-216-825-11
1-216-825-11
1-216-829-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
2.2K
2.2K
4.7K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R851
R852
R853
R854
R856
1-216-821-11
1-216-825-11
1-216-825-11
1-216-829-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
2.2K
2.2K
4.7K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R857
R858
1-216-833-11 METAL CHIP
1-216-808-11 METAL CHIP
10K
82
5%
5%
1/10W
1/10W
< FERRITE BEAD >
FB801
1-414-595-11 INDUCTOR, FERRITE BEAD
< COMPOSITION CIRCUIT BLOCK >
< FILTER >
FL801
1-518-992-11 INDICATOR TUBE, FLUORESCENT
RB801
RB802
1-233-810-21 RES, NETWORK
1-233-810-21 RES, NETWORK
100K (3216)
100K (3216)
< IC >
< SWITCH >
IC801
IC802
6-804-318-01 IC uPD780232GC-706-8BT-A
8-759-826-33 IC NJL73H400A ( )
< TRANSISTOR >
Q821
8-729-027-43 TRANSISTOR
DTC114EKA-T146
S841
S842
S843
S844
S845
1-771-349-21
1-771-349-21
1-771-349-21
1-771-349-21
1-771-349-21
SWITCH, KEYBOARD (x)
SWITCH, KEYBOARD (H)
SWITCH, KEYBOARD (X)
SWITCH, KEYBOARD (m)
SWITCH, KEYBOARD (M)
27
SCD-XE597
DISPLAY
Ref. No.
S851
S855
Part No.
KEY
LED
LOADING
Description
Remark
MAIN
Ref. No.
1-771-349-21 SWITCH, KEYBOARD (A)
1-478-268-11 ENCODER, ROTARY (. AMS >)
(PUSH ENTER)
Part No.
Description
Remark
A-4752-595-A MAIN BOARD, COMPLETE
*********************
< CAPACITOR >
< VIBRATOR >
X801
1-795-058-21 VIBRATOR, CERAMIC 5MHz
************************************************************
1-862-179-11 KEY BOARD
*********
< CONNECTOR >
CN813
1-506-481-11 PIN, CONNECTOR 2P
C201
C202
C206
C208
C212
1-126-916-11
1-126-205-11
1-115-156-11
1-115-156-11
1-128-991-21
ELECT
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
1000uF
47uF
1uF
1uF
10uF
20%
20%
C236
C238
C242
C266
C268
1-115-156-11
1-115-156-11
1-128-991-21
1-115-156-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
10uF
1uF
1uF
20%
10V
10V
50V
10V
10V
C272
C281
C302
C303
C305
1-128-991-21
1-162-966-11
1-164-156-11
1-164-156-11
1-164-156-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
20%
0.0022uF 10%
0.1uF
0.1uF
0.1uF
50V
50V
25V
25V
25V
C321
C322
C324
C325
C331
1-162-917-11
1-162-917-11
1-115-156-11
1-126-206-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
15PF
15PF
1uF
100uF
0.1uF
50V
50V
10V
6.3V
25V
C351
C362
C364
C366
C402
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.001uF
C403
C404
C405
C406
C432
1-164-217-11
1-115-156-11
1-107-826-11
1-128-992-21
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
150PF
1uF
0.1uF
47uF
0.001uF
5%
C433
C434
C435
C436
C462
1-164-217-11
1-115-156-11
1-107-826-11
1-128-992-21
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
150PF
1uF
0.1uF
47uF
0.001uF
5%
C463
C464
C465
C466
C502
1-164-217-11
1-115-156-11
1-107-826-11
1-128-992-21
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
150PF
1uF
0.1uF
47uF
0.001uF
5%
C503
C504
C505
C506
C532
1-164-217-11
1-115-156-11
1-107-826-11
1-128-992-21
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
150PF
1uF
0.1uF
47uF
0.001uF
5%
C533
C534
C535
C536
C562
1-164-217-11
1-115-156-11
1-107-826-11
1-128-992-21
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
150PF
1uF
0.1uF
47uF
0.001uF
5%
C563
C564
C565
1-164-217-11 CERAMIC CHIP
1-115-156-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
150PF
1uF
0.1uF
5%
20%
6.3V
6.3V
10V
10V
50V
< RESISTOR >
R861
R862
R863
R864
1-216-821-11
1-216-825-11
1-216-825-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
2.2K
2.2K
4.7K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
< SWITCH >
S861
1-771-349-21 SWITCH, KEYBOARD (MENU)
S862
1-771-349-21 SWITCH, KEYBOARD (SA-CD/CD)
S863
1-771-349-21 SWITCH, KEYBOARD (MULITI/2CH)
S864
1-771-349-21 SWITCH, KEYBOARD (PLAY MODE)
S865
1-771-349-21 SWITCH, KEYBOARD (TIME/TEXT)
************************************************************
LED BOARD
**********
< CAPACITOR >
C833
1-164-156-11 CERAMIC CHIP
0.1uF
25V
< CONNECTOR >
CN814
1-506-481-11 PIN, CONNECTOR 2P
< DIODE >
D801
6-500-647-01 DIODE SEL5E20C-STP15
< RESISTOR >
R834
1-216-833-11 METAL CHIP
10K
5%
1/10W
************************************************************
1-645-721-11 LOADING BOARD
**************
< CONNECTOR >
* CN151
1-568-943-11 PIN, CONNECTOR 5P
< SWITCH >
S271
1-572-086-11 SWITCH, LEAF
S272
1-572-086-11 SWITCH, LEAF
************************************************************
28
5%
5%
20%
5%
10%
20%
5%
10%
20%
5%
10%
20%
5%
10%
20%
5%
10%
20%
5%
10%
25V
25V
25V
25V
25V
50V
10V
16V
25V
25V
50V
10V
16V
25V
25V
50V
10V
16V
25V
25V
50V
10V
16V
25V
25V
50V
10V
16V
25V
25V
50V
10V
16V
SCD-XE597
MAIN
Ref. No.
Part No.
Description
Remark
C566
C701
1-128-992-21 ELECT CHIP
1-164-156-11 CERAMIC CHIP
47uF
0.1uF
20%
25V
25V
C702
C703
C704
C705
C706
1-125-837-91
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
6.3V
25V
25V
25V
25V
C709
C711
C712
C713
C714
1-126-246-11
1-164-156-11
1-164-156-11
1-117-681-11
1-126-246-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
220uF
0.1uF
0.1uF
100uF
220uF
20%
C715
C716
C721
C722
C723
1-164-156-11
1-117-681-11
1-164-156-11
1-107-826-11
1-125-837-91
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
0.1uF
0.1uF
1uF
C726
C727
C729
C730
C731
1-162-964-11
1-162-968-11
1-162-964-11
1-162-968-11
1-162-968-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C733
C734
C736
C737
C738
1-165-176-11
1-107-826-11
1-164-156-11
1-164-156-11
1-164-156-11
C739
C740
C741
C742
C743
20%
20%
4V
25V
25V
16V
4V
10%
10%
25V
16V
25V
16V
6.3V
0.001uF
0.0047uF
0.001uF
0.0047uF
0.0047uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
16V
16V
25V
25V
25V
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
C744
C745
C746
C748
C749
1-115-156-11
1-107-826-11
1-164-156-11
1-164-156-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
0.1uF
0.1uF
0.1uF
C750
C751
C752
C753
C754
1-115-156-11
1-162-927-11
1-164-156-11
1-164-156-11
1-126-246-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
1uF
100PF
0.1uF
0.1uF
220uF
C755
C756
C757
C758
C759
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
25V
25V
25V
25V
25V
C760
C761
C762
C763
C764
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
25V
25V
25V
25V
25V
C765
C766
C767
C768
C769
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
25V
25V
25V
25V
25V
20%
25V
25V
25V
25V
25V
10%
10%
5%
20%
10V
16V
25V
25V
16V
10V
50V
25V
25V
4V
Ref. No.
Part No.
Description
C770
C771
C772
C775
C776
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
Remark
C777
C778
C779
C780
C781
1-162-915-11
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10PF
0.1uF
0.1uF
0.1uF
0.1uF
C782
C783
C785
C787
C788
1-164-156-11
1-117-681-11
1-126-246-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
220uF
0.1uF
0.1uF
C789
C793
C794
C795
C796
1-164-156-11
1-164-156-11
1-164-156-11
1-117-681-11
1-117-681-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
0.1uF
0.1uF
0.1uF
100uF
100uF
C800
C804
C809
C813
C814
1-164-156-11
1-164-156-11
1-164-677-11
1-164-677-11
1-115-467-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.033uF
0.033uF
0.22uF
C815
C816
C817
C819
C820
1-164-245-11
1-162-964-11
1-162-964-11
1-115-156-11
1-164-816-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.015uF
0.001uF
0.001uF
1uF
220PF
2%
25V
50V
50V
10V
50V
C821
C822
C825
C828
C829
1-162-927-11
1-164-816-11
1-162-965-11
1-110-563-11
1-110-563-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
220PF
0.0015uF
0.068uF
0.068uF
5%
2%
10%
10%
10%
50V
50V
50V
16V
16V
C830
C832
C901
C910
C920
1-162-927-11
1-162-968-11
1-162-970-11
1-162-964-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.0047uF
0.01uF
0.001uF
0.01uF
5%
10%
10%
10%
10%
50V
50V
25V
50V
25V
C921
C923
C924
C931
C932
1-128-546-11
1-164-156-11
1-126-925-91
1-126-939-11
1-126-951-11
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
10000uF
0.1uF
470uF
10000uF
470uF
20%
10V
25V
10V
16V
35V
C933
C934
C935
C953
C954
1-164-156-11
1-126-935-11
1-126-767-11
1-164-156-11
1-126-925-91
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
0.1uF
470uF
1000uF
0.1uF
470uF
C961
C962
C970
C971
C972
1-128-991-21
1-164-156-11
1-162-970-11
1-128-552-51
1-128-991-21
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT CHIP
10uF
0.1uF
0.01uF
47uF
10uF
10%
20%
20%
50V
25V
25V
63V
50V
C973
1-126-395-11 ELECT CHIP
22uF
20%
16V
25V
25V
25V
25V
25V
0.5PF
20%
20%
50V
25V
25V
25V
25V
25V
16V
4V
25V
25V
20%
20%
25V
25V
25V
16V
16V
10%
10%
10%
25V
25V
16V
16V
10V
10%
10%
10%
20%
20%
20%
20%
20%
20%
20%
25V
16V
16V
25V
10V
29
SCD-XE597
MAIN
Ref. No.
Part No.
Description
< CONNECTOR >
CN701
CN702
CN703
* CN705
CN901
1-784-368-11
1-784-387-11
1-793-989-21
1-568-954-11
1-784-924-11
CONNECTOR, FFC/FPC 9P
CONNECTOR, FFC/FPC 31P
CONNECTOR, FFC/FPC 13P
PIN, CONNECTOR 5P
PIN, CONNECTOR 8P
< DIODE >
D321
D509
D511
D921
D922
8-719-027-76
8-719-941-09
8-719-941-09
8-719-053-18
8-719-053-18
DIODE
DIODE
DIODE
DIODE
DIODE
1SS357-TPH3
DAP202UT106
DAP202UT106
1SR154-400TE-25
1SR154-400TE-25
D923
D924
D931
D932
D933
8-719-053-18
8-719-053-18
8-719-053-18
8-719-053-18
8-719-053-18
DIODE
DIODE
DIODE
DIODE
DIODE
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
D934
D936
D937
D960
D961
8-719-053-18
8-719-053-18
8-719-053-18
8-719-941-86
8-719-941-86
DIODE
DIODE
DIODE
DIODE
DIODE
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
DAN202UT106
DAN202UT106
D963
D971
D972
D973
6-500-696-01
8-719-053-18
8-719-083-87
8-719-069-60
DIODE
DIODE
DIODE
DIODE
UDZSTE-173.0B
1SR154-400TE-25
UDZS-TE17-33B
UDZSTE-179.1B
IC985
Part No.
Description
Remark
8-759-460-81 IC BA12FP-E2
< JACK >
J351
1-785-536-11 JACK, PIN 6P
< TRANSISTOR >
Q301
Q303
Q305
Q401
Q402
8-729-924-04
8-729-924-04
8-729-924-04
8-729-141-73
8-729-141-73
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
UN5116-TX
UN5116-TX
UN5116-TX
2SC3624A-T1L15L16
2SC3624A-T1L15L16
Q431
Q432
Q462
Q463
Q501
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
Q502
Q531
Q532
Q562
Q563
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
Q961
Q971
8-729-027-56 TRANSISTOR
8-729-019-72 TRANSISTOR
DTC143TKA-T146
2SB1260T100
< RESISTOR >
1-216-833-11
1-216-839-11
1-216-857-11
1-216-864-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
10K
33K
1M
0
1K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R324
R326
R328
R330
R404
1-216-809-11
1-216-801-11
1-216-801-11
1-216-801-11
1-216-827-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
22
22
22
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< IC >
R407
R408
R409
R411
R434
1-216-845-11
1-216-815-11
1-216-813-11
1-216-809-11
1-216-827-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
330
220
100
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
ETP910 1-537-771-21 TERMINAL BOARD, GROUND
< FERRITE BEAD >
1-500-283-11 INDUCTOR, FERRITE BEAD
1-414-595-11 INDUCTOR, FERRITE BEAD
1-414-595-11 INDUCTOR, FERRITE BEAD
< FILTER >
FL606
Ref. No.
R201
R202
R321
R322
R323
< GROUND TERMINAL BOARD >
FB201
FB703
FB710
Remark
1-234-177-21 FILTER, CHIP EMI
IC200
IC230
IC260
IC320
IC330
6-703-420-01
6-703-420-01
6-703-420-01
8-759-549-25
6-600-012-01
IC
IC
IC
IC
IC
DSD1751DBQR
DSD1751DBQR
DSD1751DBQR
SN74LVU04APWR
TOTX141L
R437
R438
R439
R464
R467
1-216-845-11
1-216-815-11
1-216-813-11
1-216-827-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
330
220
3.3K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
IC400
IC430
IC460
IC701
* IC702
8-759-710-97
8-759-710-97
8-759-710-97
8-759-636-64
6-703-671-01
IC
IC
IC
IC
IC
NJM4565M (TE2)
NJM4565M (TE2)
NJM4565M (TE2)
M51957BFP-600C
BR9040F-WE2
R468
R469
R504
R507
R508
1-216-815-11
1-216-813-11
1-216-827-11
1-216-845-11
1-216-815-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330
220
3.3K
100K
330
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
IC703
IC705
IC706
IC708
IC712
6-700-398-01
6-804-317-01
8-752-420-59
6-702-336-01
6-702-157-01
IC
IC
IC
IC
IC
uPC2918T-E1
HD6432238RN51TEV
CXD2754Q
MSM56V16160F-8TK7R1
FAN8035L
R509
R511
R534
R537
R538
1-216-813-11
1-216-809-11
1-216-827-11
1-216-845-11
1-216-815-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
100
3.3K
100K
330
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
IC920
IC950
6-705-463-01 IC BA33BC0T
6-705-469-01 IC BA50BC0FP-E2
R539
R564
1-216-813-11 METAL CHIP
1-216-827-11 METAL CHIP
220
3.3K
5%
5%
1/10W
1/10W
30
SCD-XE597
MAIN
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
POWER SW
Description
PT
Remark
R567
R568
R569
1-216-845-11 METAL CHIP
1-216-815-11 METAL CHIP
1-216-813-11 METAL CHIP
100K
330
220
5%
5%
5%
1/10W
1/10W
1/10W
R979
R701
R702
R703
R707
R708
1-216-821-11
1-216-833-11
1-216-833-11
1-216-821-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
10K
1K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RB301
RB302
RB402
RB410
RB432
1-233-414-11
1-233-873-21
1-233-419-21
1-233-413-11
1-233-419-21
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
4.7K (3216)
220K (3216)
6.8K (3216)
2.2K (3216)
6.8K (3216)
R731
R752
R781
R782
R783
1-216-833-11
1-216-864-11
1-216-821-11
1-216-841-11
1-216-833-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
0
1K
47K
10K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
RB441
RB442
RB462
RB502
RB532
1-233-413-11
1-233-413-11
1-233-419-21
1-233-419-21
1-233-419-21
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
2.2K (3216)
2.2K (3216)
6.8K (3216)
6.8K (3216)
6.8K (3216)
R791
R804
R806
R819
R820
1-216-805-11
1-216-815-11
1-216-150-91
1-216-847-11
1-216-847-11
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
47
330
10
150K
150K
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/10W
1/10W
RB562
RB601
RB602
RB603
RB604
1-233-419-21
1-236-908-11
1-233-412-11
1-233-577-11
1-233-414-11
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
6.8K (3216)
10K (3216)
1.0K (3216)
470 (3216)
4.7K (3216)
R831
R840
R846
R852
R853
1-216-833-11
1-216-845-11
1-216-842-11
1-216-845-11
1-216-842-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
56K
100K
56K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RB605
RB606
RB607
RB609
RB610
1-236-908-11
1-236-908-11
1-236-908-11
1-236-908-11
1-233-578-11
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
10K (3216)
10K (3216)
10K (3216)
10K (3216)
47K (3216)
R857
R858
R860
R861
R865
1-216-839-11
1-216-846-11
1-216-855-11
1-216-850-11
1-216-842-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
120K
680K
270K
56K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RB611
RB612
RB613
RB615
RB616
1-236-908-11
1-236-908-11
1-236-908-11
1-233-577-11
1-233-577-11
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
RES, CHIP NETWORK
10K (3216)
10K (3216)
10K (3216)
470 (3216)
470 (3216)
R866
R869
R870
R871
R872
1-216-839-11
1-216-842-11
1-216-839-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
56K
33K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RB617
1-233-577-11 RES, CHIP NETWORK
470 (3216)
R874
R876
R877
R878
R880
1-216-839-11
1-216-844-11
1-216-853-11
1-216-853-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
82K
470K
470K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R885
R886
R888
R889
R892
1-216-835-11
1-216-844-11
1-216-835-11
1-216-864-11
1-216-846-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
15K
82K
15K
0
120K
5%
5%
5%
1/10W
1/10W
1/10W
0 C891
5%
1/10W
* CN891
R893
R894
R895
R897
R899
1-216-846-11
1-216-842-11
1-216-842-11
1-216-853-11
1-216-849-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120K
56K
56K
470K
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R961
R962
R963
R971
R972
1-216-821-11
1-216-821-11
1-216-821-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R973
R975
R976
R977
R978
1-216-827-11
1-216-839-11
1-216-809-11
1-216-809-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
33K
100
100
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1-216-833-11 METAL CHIP
10K
5%
1/10W
< COMPOSITION CIRCUIT BLOCK >
< VIBRATOR >
X321
1-795-535-21 VIBRATOR, CRYSTAL
************************************************************
1-862-182-11 POWER SW BOARD
****************
< CAPACITOR >
1-113-920-11 CERAMIC
0.0022uF 20%
250V
< CONNECTOR >
1-580-230-31 PIN, CONNECTOR (PC BOARD) 2P
< SWITCH >
0 S891
1-762-581-11 SWITCH, AC POWER PUSH (1 KEY)
************************************************************
1-862-181-11 PT BOARD
********
< CAPACITOR >
0 C101
1-113-920-11 CERAMIC
0.0022uF 20%
250V
< CONNECTOR >
* CN101 1-568-226-11 PIN, CONNECTOR (3.96mm PITCH) 2P
************************************************************
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
31
SCD-XE597
RF
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Q001
Q002
< CAPACITOR >
C001
C002
C004
C005
C006
1-107-726-91
1-107-726-91
1-124-778-00
1-162-966-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
22uF
0.0022uF
0.0022uF
10%
10%
20%
10%
10%
16V
16V
6.3V
50V
50V
C007
C008
C009
C011
C015
1-162-966-11
1-162-966-11
1-124-779-00
1-107-726-91
1-162-968-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.0022uF
10uF
0.01uF
0.0047uF
10%
10%
20%
10%
10%
50V
50V
16V
16V
50V
C016
C017
C018
C019
C021
1-162-968-11
1-126-206-11
1-115-416-11
1-164-739-11
1-124-779-00
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.0047uF
100uF
0.001uF
560PF
10uF
10%
20%
5%
5%
20%
50V
6.3V
25V
50V
16V
C022
C023
C024
C025
C026
1-107-826-11
1-126-206-11
1-115-416-11
1-107-826-11
1-107-726-91
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
0.001uF
0.1uF
0.01uF
10%
20%
5%
10%
10%
16V
6.3V
25V
16V
16V
C027
C028
C031
C032
C033
1-107-726-91
1-107-826-11
1-107-826-11
1-107-826-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.1uF
0.1uF
0.001uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
50V
C034
C035
C036
C038
C039
1-164-227-11
1-107-826-11
1-165-176-11
1-165-176-11
1-107-726-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.1uF
0.047uF
0.047uF
0.01uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C040
C043
C044
C046
C047
1-164-217-11
1-107-826-11
1-124-779-00
1-107-726-91
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
150PF
0.1uF
10uF
0.01uF
0.1uF
5%
10%
20%
10%
10%
50V
16V
16V
16V
16V
C048
1-107-726-91 CERAMIC CHIP
0.01uF
10%
16V
1-815-031-11 CONNECTOR, FFC/FPC (ZIF) 24P
1-784-879-21 CONNECTOR, FFC (LIF (NON-ZIF)) 31P
1-784-861-21 CONNECTOR, FFC (LIF (NON-ZIF)) 9P
< DIODE >
D001
D004
8-729-903-46 TRANSISTOR
8-729-903-46 TRANSISTOR
2SB1132-T100-QR
2SB1132-T100-QR
< RESISTOR >
R002
R003
R004
R005
R006
1-216-809-11
1-216-809-11
1-216-864-11
1-216-845-11
1-216-838-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
100
100
0
100K
27K
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R007
R008
R009
R010
R011
1-216-803-11
1-216-803-11
1-216-820-11
1-216-841-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33
33
820
47K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R013
R018
R020
R023
R025
1-216-833-11
1-216-833-11
1-216-803-11
1-216-803-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
33
33
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R029
R037
R038
R045
R052
1-216-809-11
1-216-834-11
1-216-861-11
1-216-813-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
100
12K
2.2M
220
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R053
1-216-864-11 SHORT CHIP
0
R054
1-216-864-11 SHORT CHIP
0
R055
1-216-864-11 SHORT CHIP
0
************************************************************
MISCELLANEOUS
**************
06
0 10
58
253
0 255
258
M901
1-777-071-43
1-443-287-11
1-828-333-11
1-829-172-11
A-4713-410-A
CORD, POWER
TRANSFORMER, POWER
WIRE (FLAT TYPE) (13 CORE)
WIRE (FLAT TYPE) (31 CORE)
PICK-UP UNIT (DBU-3)
1-824-106-12 CABLE, FLEXIBLE FLAT (24 CORE)
A-4604-363-A MOTOR (L) ASSY (LOADING)
ACCESSORIES
************
< CONNECTOR >
CN001
CN002
CN003
Remark
< TRANSISTOR >
A-4750-527-A RF BOARD, COMPLETE
*******************
1-478-636-11 COMMANDER, STANDARD (RM-SX800)
1-790-735-12 CORD, CONNECTION
2-021-059-11 MANUAL, INSTRUCTION
(ENGLISH, FRENCH, GERMAN, SPANISH)
2-021-059-21 MANUAL, INSTRUCTION
(DUTCH, SWEDISH, ITALIAN, PORTUGUESE) (AEP)
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
< IC >
IC001
6-703-445-01 IC SP3726A
< COIL >
L001
L002
1-412-031-11 INDUCTOR
1-412-031-11 INDUCTOR
47uH
47uH
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
32
SCD-XE597
AEP Model
UK Model
SERVICE MANUAL
Ver. 1.2 2005.05
SUPPLEMENT-1
Subject: TEST MODE and ELECTRICAL ADJUSTMENT
9-879-005-81
SCD-XE597
SECTION 1
TEST MODE
1. DIAG MODE of The Test Mode
While press [MENU] and [PUSH ENTER] buttons, press the [POWER] button to turn the power on and enter the Test Mode and display “DIAG
MODE”.
2. Operating The Test Mode
Procedure:
1. Turn the l AMS L knob to select the command number (hexadecimal number) (refer to the following table for command
number).
2. Press the [PUSH ENTER] button to execute the selected command item.
3. The Commands in Test Mode
Command No.
Command name
12
LD ON/OFF
Item
Turn on/off the laser diode
13
SPIN ON/OFF
Turn on/off the spindle motor
14
FSRV ON/OFF
Turn on/off the focus servo
15
TSRV ON/OFF
Turn on/off the tracking servo
16
CLV ON/OFF
17
SSRV ON/OFF
Turn on/off the spindle CLV servo, when both focus servo and tracking servo are on
Turn on/off the spindle CLV servo, when all servo of focus servo, tracking servo
and spindle servo are on
18
ALL SRV ON
Turn on all servo
19
ALL SRV OFF
Turn off all servo
1A
DISC STOP
24
ADJ FCSBIAS
Stop the disc rotation (useful as overdrived)
Automatically adjust the focus bias (*1)
27
FOCUS AGC
Automatically adjust the focus servo gain (*1)
31
PI/FE OFSET
Automatically adjust the offset signal of PI, PE and TE (*1)
45
TRACKING AGC
61
DISC DETECT
Automatically adjust the focus servo gain (*1)
Judge the disc type (when SA-CD, “SL” or “DL” is displayed)
7C
FJUMP TEST
81
SYSTEM VERSION
Focus jump test mode
82
I/F VERSION
8D
CEL
Initialization
8F
U&OTHERS
Initialization
92
ERR CHECK
Error rate display (to stop, press the x button)
Display the version of system microcomputer for 2 seconds
Display the version of IF microcomputer for 2 seconds
for CD display “92 C1 C2 0xff”
for SA-CD display “92 PI1 PO PI2”
93
WATER MARK
WaterMark display
display “93 xxxx” (“xxxx” is value of pspamp)
9D
PLAY&RFD ON
Measuring the jitter (to stop, press the x button)
display: “9D xx 0xff 0xff” (“xx” is measuring value of jitter)
*1) Not used in servicing
4. The Commands in Automatic Electrical Adjustments
(Use the commands When The system version number is ver1.24 and higher)
2
Command No.
Item
B0
RAM clear
B1
Writing
B2
Check writing data
SCD-XE597
SECTION 2
ELECTRICAL ADJUSTMENTS
GENERAL DESCRIPTION
After parts to the circuit (OPTICAL PICK-UP (DBU-3), RF
BOARD, MAIN BOARD, EEPROM (IC702), MASTERCOM
(IC705), DSP (IC706), so on) are replaced, readjusting is necessary.
1. ROM Version Check
Procedure:
1. While pressing [PUSH ENTER] button and [MENU] buttons,
press the [POWER] button to turn the set on.
“DIAG MODE” is displayed on the screen.
2. Select “81 SYS-F VER” by tuning l AMS L knob.
3. Press [PUSH ENTER] button.
4. Check the version of ROM.
“SYS. VER X.XX” is displayed.
5. Select “82 I/F-F VER”
“I/F VER X.XX” is displayed.
Automatically return “81 SYS-F VER”
2. U-CON Check (The system version number is Ver
1.24 and higher)
This checking must be performed before any other checking.
CHECK DISC LIST
Use the following disc on this check.
SATD-S4: PART No. J-2501-184-A
SATD-S5: PART No. J-2501-215-A
Procedure:
1. While pressing [PUSH ENTER] button and [MENU] buttons,
press the [POWER] button to turn the set on.
“DIAG MODE” is displayed on the screen.
2. Push the Z button to open the tray.
3. Load CD to tray.
4. Push the Z button to close the tray.
5. Turn “JOG DIAL” clockwise until “B0” and press the [PUSH
ENTER] (Used time : 7 sec) “FFFF” is displayed.
6. Turn “JOG DIAL” clockwise until “B1” and press the [PUSH
ENTER].
Display shows “-9” and the numbering is counting down until
“-0” lastly, “****” (4 DIGITS VALUE) appears. (Used time :
33 sec)
7. Turn “JOG DIAL” clockwise until “B2” and press the [PUSH
ENTER].
Display shows the last number that appear at. STEP NO.7.
Confirm that the value is “08D0”>THE VALUE>“04D0”
8. Push the Z button to open the tray.
9. Unload CD from tray.
10. Push the Z button to close the tray.
11. Press the [POWER] button to turn the set off. (Do not continue
with another test mode without power off.)
3. Optical Sensitivity Check
CHECK DISC LIST
Use the following hybrid disc on this check.
HLXA-509 : PART No. J-6090-090-A
SACD HYBRID DISC (MARKET DISC)
Connection:
oscilloscope
Procedure:
1. Press the Z button.
2. Insert SACD hybrid disc (market disc).
3. Connect the oscilloscope to pin 27 and pin31 of CN702.
4. Observe the MIRR waveform immediately after the disc
chucking is completed when disc identification is made.
MIRR signal waveform
T
1V/DIV, 5ms/DIV
5. Read the measurement of ∆ T.
IF 7.5ms <∆ T<9.7ms> OK
OTHERS>NG
6. When the system version number is before ver.1.24, and if the
MIRR waveform is NG (No Good), change the values of R892
and R893, and then repeat step4 and after.
9.7 ms< ∆ t
R892/R893 120 kΩ → 110 kΩ (1-218-741-11)
∆ t< 6.9 ms
R892/R893 120 kΩ → 130 kΩ (1-218-743-11)
4. Mode Setting For Shipping (MAIN board on EEPROM
(IC702) is replaced.)
Be sure to set the unit to the specified modes as stated in the steps
below after sampling inspections by the QA dept.
Or before shipping.
Procedure:
1. While pressing [PUSH ENTER] and [MENU] buttons, press the
[POWER] button to turn the set on.
“DIAG MODE” is displayed in the screen.
2. Turn jog until the specified mode (According to version) is
displayed:
a) “8D SETUP” : CEL
b) “8F SETUP” : U & OTHERS
3. Press jog one single time.
“INIT START” is displayed and Mode setting for shipping
starts.
4. Wait until “INITIAL OK” appears on the display.
5. By this operation, the unit is initialized as follows:
PLAY MODE
ALL DISCS
COMMAND MODE
CD 1
REPEAT
OFF
SACD/CD
SACD
M/2ch
MULTI
6. After 2 to 3 sec., Press the [POWER] button to turn the set off.
Note : When EEPROM (IC702) is replaced, the initialization
is necessary.
MAIN board
CN702 (PIN27)
CN702 (PIN31)
+
–
3
SCD-XE597
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
Date
Description of Revision
1.0
2004.06
New
1.1
2004.11
Addition of silver model for UK
1.2
2005.05
Addition of TEST MODE and ELECTRICAL ADJUSTMENT with
SUPPLEMENT-1 (9-879-005-81)
1.3
2006.02
Addition of silver (Hair-line Finish) model
(SPM-06013)