Download HCD-WZ8D

HCD-WZ8D
SERVICE MANUAL
AEP Model
UK Model
E Model
Australian Model
Ver 1.0 2003. 07
• HCD-WZ8D is the tuner, and the CD/
DVD player section in MHC-WZ8D.
Model Name Using Similar Mechanism
DVD
Section
HCD-SA30
DVD Mechanism Type
CDM77A-DVBU20
Optical Pick-up Name
TDP022W
SPECIFICATIONS
CD/DVD player section
Laser
Semiconductor laser
(DVD: λ=650 nm,
CD: λ=780 nm)
Emission duration:
continuous
Frequency response
DVD (PCM 48 kHz):
2 Hz – 22 kHz = (±1 dB)
CD: 2 Hz – 20 kHz =
(±1 dB)
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 90 dB
Video color system format
NTSC, PAL
DVD DIGITAL (OPTICAL) OUT (European, Russian
and Australian models only) (Square optical connector
jack, rear panel):
Optical Wavelength:
660 nm
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
Russian model
Other models
Antenna
Antenna terminals
Intermediate frequency
65.0 – 74.0 MHz
(There is no stereo effect)
87.5 – 108.0 MHz
87.5 – 108.0 MHz
FM lead antenna
75 ohms unbalanced
10.7 MHz
AM tuner section
Tuning range
Latin American model:
530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
531 – 1,710 kHz
(with the tuning interval
set at 9 kHz)
European, Russian and Middle Eastern models:
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)
Other models:
531 – 1,602 kHz
(with the tuning interval
set at 9 kHz)
530 – 1,710 kHz
(with the tuning interval
set at 10 kHz)
Antenna
Antenna terminals
Intermediate frequency
AM loop antenna
External antenna terminal
450 kHz
Power consumption
European and Russian models:
235 watts
0.3 watts (in Power Saving
Mode)
Other models:
260 watts
Dimensions (w/h/d)
CD/DVD player/Tuner: Approx. 255 × 135 ×
355 mm
Mass
CD/DVD player/Tuner: Approx. 3.0 kg
Supplied accessories:
Remote Commander (1)
Batteries (2)
AM loop antenna (1)
FM lead antenna (1)
Speaker pads (20)
Speaker cords (5)
Video cord (1)
Design and specifications are subject to change
without notice.
General
Power requirements
Power voltage is DC 9V and fed with STEREO
CASSETTE DECK AMPLIFIER (DXA-WZ8D)
from the external SYSTEM CONTROL connectors.
CD/DVD PLAYER TUNER
9-877-415-01
Sony Corporation
2003G1678-1
© 2003.07
Home Audio Company
Published by Sony Engineering Corporation
HCD-WZ8D
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Laser component in this product is capable
of emitting radiation exceeding the limit for
Class 1.
This appliance is
classified as a CLASS 1
LASER product. This
label is located on the
rear exterior.
The following caution label is located inside the apparatus.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
TABLE OF CONTENTS
1. GENERAL ·········································································· 4
2. DISASSEMBLY
2-1. Case ··············································································· 7
2-2. Front Panel Assy ···························································· 8
2-3. PANEL Board, CD-TC-SW Board,
ENTER-SW Board, BACK LIGHT Board,
LCD Board ···································································· 8
2-4. 4CH-VOL Board, VIDEO Board ·································· 9
2-5. MAIN Board, REGULATOR Board,
HP AMP Board ······························································ 9
2-6. DVD Mechanism (CDM77A-DVBU20) ····················· 10
2-7. DMB03 Board ····························································· 10
2-8. MIC Board ··································································· 11
2-9. Tray (AU) ···································································· 11
2-10. MS-128 Board ····························································· 12
2-11. Base Unit ····································································· 12
2-12. Pick-up Unit (TDP022W) ··········································· 13
3. TEST MODE ···································································· 14
4. DIAGRAMS
4-1. Block Diagrams – RF Servo Section – ······················· 25
– Video Section – ····························· 26
– Audio Section – ···························· 27
– Main Section – ······························ 28
4-2. Printed Wiring Board – RF Board – ···························· 29
4-3. Schematic Diagram – RF Board – ···························· 30
4-4. Printed Wiring Board – DMB03 Board (Side A) – ····· 31
4-5. Printed Wiring Board – DMB03 Board (Side B) – ····· 32
4-6. Schematic Diagram – DMB03 Board (1/9) – ··········· 33
4-7. Schematic Diagram – DMB03 Board (2/9) – ··········· 34
4-8. Schematic Diagram – DMB03 Board (3/9) – ··········· 35
4-9. Schematic Diagram – DMB03 Board (4/9) – ··········· 36
4-10. Schematic Diagram – DMB03 Board (5/9) – ··········· 37
4-11. Schematic Diagram – DMB03 Board (6/9) – ··········· 38
4-12. Schematic Diagram – DMB03 Board (7/9) – ··········· 39
4-13. Schematic Diagram – DMB03 Board (8/9) – ··········· 40
4-14. Schematic Diagram – DMB03 Board (9/9) – ··········· 41
4-15. Printed Wiring Board – Main Section – ······················ 42
4-16. Schematic Diagram – Main Section (1/2) – ············· 43
4-17. Schematic Diagram – Main Section (2/2) – ············· 44
4-18. Printed Wiring Board – PANEL Board – ···················· 45
4-19. Schematic Diagram – PANEL Board – ···················· 46
4-20. Printed Wiring Board – LCD/Switch Section – ·········· 47
4-21. Schematic Diagram – LCD/Switch Section – ·········· 48
4-22. Printed Wiring Board – REGULATOR Board – ········· 49
4-23. Schematic Diagram – REGULATOR Board – ········· 50
4-24. Printed Wiring Board – 4CH-VOL Board – ················ 51
4-25. Schematic Diagram – 4CH-VOL Board – ················ 52
4-26. Printed Wiring Board – VIDEO/MIC Board – ············ 53
4-27. Schematic Diagram – VIDEO/MIC Board – ············ 54
4-28. IC Block Diagrams ······················································ 55
4-29. IC Pin Function Description ········································ 61
5. EXPLODED VIEWS
5-1. Front Panel Section ····················································· 70
5-2. Chassis Section ···························································· 71
5-3. DVD Mechanism Deck Section ·································· 73
6. ELECTRICAL PARTS LIST ······································· 74
2
HCD-WZ8D
[When bringing in the equipment for service]
In case of repairing, please bring the entire system set([HCD-WZ5,
DXA-WZ5],except for the speaker) to the service station.
MODEL IDENTIFICATION
— BACK PANEL —
PARTS No.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
MODEL
PARTS No.
AEP, UK models
4-244-897-0s
EA model
4-244-897-1s
E3, E15 models
4-244-897-2s
E2 model
4-244-897-3s
AUS models
4-244-897-4s
TH model
4-244-897-6s
KR model
4-244-897-7s
MY, SP models
4-244-897-8s
RU models
4-244-897-9s
PH model
4-247-928-0s
• Abbreviation
AUS : Australian model
E2
: 120V AC area in E model
E3
: 240V AC area in E model
E15 : 220-240V AC area in E model
EA
: Saudi Arabia model
KR
: Korean model
MY : Malaysia model
PH
: Philippines model
RU
: Russian model
SP
: Singapore model
TH
: Thai model
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
3
HCD-WZ8D
SECTION 1
GENERAL
This section is extracted
from instruction manual.
List of button locations and reference pages
Illustration number
r
How to use this page
Use this page to find the location of buttons and other
parts of the system that are mentioned in the text.
TAPE A/B 3 (41, 42)
R
Name of button/part
R
Reference page
Main unit
BUTTON DESCRIPTIONS
ALPHABETICAL ORDER
A–J
K–Z
ALBUM – qg (14, 17, 19)
ALBUM + qf (14, 17, 19)
CD SYNC 9 (41)
COLOR SELECT w; (50)
Control lever 7 (11, 45)
Disc tray wg (13)
DISPLAY ql (39, 49, 51, 52)
Display window wf
DVD 5 (11, 12, 13, 19, 37, 41,
42)
DVD MENU qf (16, 27)
DVD TOP MENU qg (16)
ECHO LEVEL*1 wa (46)
EFFECT qj (43, 45)
EQ EDIT qk (45, 60)
GROOVE 7 (43)
Headphone jack qd
KARAOKE/MPX*2 qh (45)
MD (VIDEO) 2 (42, 55)
MIC LEVEL*2 ws (45)
Microphone jacks*2*3 wd
MOVIE MODE 7 (43)
MPX*4 qh (46)
MUSIC MODE 7 (43, 45)
PUSH ENTER 7 (12, 16, 17, 18,
19, 21, 23, 26, 28, 31, 36, 45,
46, 47, 48)
Remote sensor qs
SOUND FIELD 7 (43)
TAPE A/B 3 (40, 41, 42, 46)
TUNER/BAND 6 (36, 37, 42)
VOLUME qa (47)
?/1 (power) 1 (10, 37, 47, 55,
60)
X (pause) 4 (10, 14, 40)
nN (play) 4 (14, 30, 40, 41,
46)
x (stop) 4 (11, 14, 27, 37, 40,
41, 46, 60)
+M> (fast forward/go
forward) 4 (14, 36, 40)
.m– (rewind/go back) 4
(14, 36, 40)
Z (open/eject) 8 (13)
z START (recording start) q;
(41, 46)
*1
*2
*3
*4
Except for European, Russian
and Latin American models
Except for European and
Russian models
Microphone jacks for:
Latin American model: 1
Asian, Australian and Middle
Eastern models: 2
European and Russian models
only
CD/DVD player/Tuner
Setting the clock
Use buttons on the remote for the operation.
To adjust the clock
1
2
3
4
5
1
2
Press CLOCK/TIMER SET.
3
Do the same procedures as step 3 to 6
above.
6
Press ?/1 to turn on the system.
Press CLOCK/TIMER SET.
Press M or m repeatedly to set the hour.
Press ,.
Press M or m repeatedly to set the
minute.
Press ENTER.
The clock starts working.
4
Press M or m repeatedly to select “CLOCK
SET?”, then press ENTER.
HCD-WZ8D
Remote control
ALPHABETICAL ORDER
BUTTON DESCRIPTIONS
A–O
P–Z
ALBUM – wa (14, 17, 19)
ALBUM + ws (14, 17, 19)
ANGLE wh (26)
AUDIO wj (23)
BAND 8 (36, 37)
CLEAR qa (19, 20, 22)
CLOCK/TIMER SELECT es
(48, 49)
CLOCK/TIMER SET ef (12, 47,
48)
COMMAND MODE switch qs
(10)
DIMMER e; (50)
DISPLAY ea (39, 49, 51, 52)
DVD DISPLAY qh (17, 18, 21,
23, 26, 28, 34, 52, 53)
DVD MENU ws (16, 27)
DVD SET UP qj (12, 15, 24, 26,
29, 31, 35, 61)
DVD TOP MENU wa (16)
ENTER w; (12, 16, 17, 18, 19, 21,
23, 26, 28, 31, 36, 45, 46, 47,
48)
FUNCTION 7 (12, 13, 19, 36,
37, 40, 47)
GROOVE 2 (43)
KEY CONTROL 5 (43, 46)
MOVIE MODE qk (43)
MUSIC MODE ql (43, 45)
Number buttons wk (15, 16, 20,
22, 25, 26, 28)
PLAY MODE/DIRECTION ed
(14, 19, 40, 41, 42, 46)
PRESET –/+ wf (36, 37)
PREV/NEXT wf (14)
REPEAT/FM MODE 6 (18, 38)
SELECT wd (16)
SLEEP eg (47)
SOUND FIELD 9 (43)
SUBTITLE wl (24)
TUNER MEMORY 5 (36)
TUNING MODE 4 (36, 37)
TUNING –/+ qd (36, 38)
TV CH –/+ wf (10)
TV/VIDEO 3 (10)
VOL +/– wg (10, 47)
eh
eg
ef
ed
es
ea
e;
wl
wk
wj
wh
wg
wf
wd
ws
wa
w;
ql
?/1 (power) 1 (10, 47)
m/M (rewind/fast forward)
qd (14, 36, 40)
SLOW t/T qd (14)
./> (go back/go forward)
wf (14, 36, 40)
nN (play) wd (14, 30, 40, 41,
46)
X (pause) qg (14, 40)
x (stop) qf (14, 40, 41, 46)
M/m/</, w; (12, 16, 23, 28,
33, 47)
O RETURN q; (16, 28)
TV ?/1 eh (10)
1
1
2
3
4
5
6
7
8
9
>10
10/0
2
3
4
5
6
7
8
9
0
qa
qs
qd
qf
qg
qh
qj
qk
5
HCD-WZ8D
Getting Started
Hooking up the system
Perform the following procedures 1 to 7 to hook up your system using the supplied cords and
accessories. European model is used for illustration purpose.
To center
speaker
AM loop antenna
FM lead antenna
CD/DVD player/Tuner
Amplifier/Tape deck
To front speaker (right)
To front speaker
(left)
To surround speaker (right)
To surround speaker (left)
Preparation
Note
Place the components as shown below.
Amplifier/
Tape deck
CD/DVD player/
Tuner
The system cable is used to send signals and electricity
between the components for interlinked operation.
Be sure to insert the connector horizontally until it
clicks into place. Otherwise the system will not operate
correctly.
2 Connect the speakers.
1 Connect the system control cables to
the SYSTEM CONTROL connectors on
the tape deck.
Connect to the same numbered jack in the
order indicated on the rear panel.
6
Be sure to match the appropriate speaker
cords from the speaker terminals to the
corresponding SPEAKER terminals on the
tape deck.
HCD-WZ8D
SECTION 2
DISASSEMBLY
• The equipment can be removed using the following procedure.
SET
CASE
FRONT PANEL ASSY
PANEL BOARD, CD-TC SW BOARD,
ENTER-SW BOARD,
BACK LIGHT BOARD, LCD BOARD
4CH-VOL BOARD,
VIDEO BOARD
DVD MECHANISM
(CDM77B-DVBU20)
MAIN BOARD,
REGULATOR BOARD,
HP AMP BOARD
TRAY (AU)
DMB03 BOARD
MS-128 BOARD
BASE UNIT
PICK-UP UNIT
(TDP022W)
Note : Follow the disassembly procedure in the numerical order given.
2-1. Case
4 case
3 two screws
(case 3 TP2)
1 three screws
(+BVTP 3 × 8)
2 two screws
(case 3 TP2)
7
HCD-WZ8D
2-2. Front Panel Assy
How to eject the disc tray when the
main power cannot be turned on.
3 loading panel
5 wire
(NO601)
4 screw
(+BVTP 3 × 8)
1
q; wire (flat type)
(23 core) (CN109)
9 connector
(CN108)
2
8
bottom side
7 claw
qa front panel
section
6 three screws
(+BVTP 3 × 8)
2-3. PANEL Board, CD-TC-SW Board, ENTER-SW Board, BACK LIGHT Board, LCD Board
ql Remove the soldering.
qk two screws
(+BVTP 2.6 × 8)
w; LCD board
wa LCD assy
qg four screws
(+BVTP 2.6 × 8)
qh three claws
9 connector
(CN602)
qj BACK LIGHT board
8 eight screws
(+BVTP 2.6 × 8)
qd wire (flat type)
(23 core) (CN605)
qf PANEL board
6 connector
(CN604)
4 two screws
(+BVTP 2.6 × 8)
7 CD-TC SW board
3 button (cursor)
5 two claws
q; connector
(CN603)
qa two screws
(+BVTP 2.6 × 8)
2 nut
1 knob (volume)
8
qs ENTER-SW board
HCD-WZ8D
2-4. 4CH-VOL Board, VIDEO Board
7 two screws
(+BVTP 3 × 8)
2 wire (flat type)
(11/15 core)
qd cord connector
(CN107)
3 seven screws
(+BVTP 3 × 8)
5 cord connector
(CN302)
1 wire (flat type)
(23/25 core)
4 four screws
(+BVTP 3 × 8)
8 4CH-VOL board
6 wire (flat type)
(25/21 core)
qf back panel
qa connector
(CN507)
qs cord connector
(CN503,CN504)
q; VIDEO board
9 wire (flat type)
(17 core)
2-5. MAIN Board, REGULATOR Board, HP AMP Board
qa MAIN board
q; two claws
9 four screws
(+BVTP 3 × 8)
8 screw
(+BVTP 3 × 8)
qs REGULATOR board
6 wire (flat type)
(5 core) (CN103)
5 wire (flat type)
(11 core) (CN102)
7 connector
(CN109)
4 wire (flat type)
(7 core) (CN101)
2 screw
(+BVTP 3 × 8)
1 connector
(CN601)
3 HP AMP board
9
HCD-WZ8D
2-6. DVD Mechanism (CDM77A-DVBU20)
4 DVD mechanism
(CDM77B-DVBU20)
2 three screws
(+BVTP 3 × 8)
3 wire (flat type)
(29 core) (RF board)
1 wire (flat type)
(5 core) (CN103)
2-7. DMB03 Board
5 claw
4 four screws (+BV)
q; bracket (CDM)
6 wire (flat type)
(25/21 core) (CN107)
3 screw
(+BVTP 3 × 8)
qa DMB03 board
1 wire (flat type)
(7 core) (CN101)
2 wire (flat type)
(11 core) (CN102)
9 heat sink (DMB)
8 four screws
(+BVTP 3 × 8)
10
7 wire (flat type)
(17 core) (CN105)
HCD-WZ8D
2-8. MIC Board
2 claw
1 two screws
(+BVTP 3 × 8)
3 connector
(CN701)
4 MIC board
2-9. Tray (AU)
bottom side
3 two claws
1
2
4 tray (AU)
11
HCD-WZ8D
2-10. MS-128 Board
1 belt
3 MS-128 board
2 four claws
2-11. Base Unit
1 belt
7 chuck cam
3 puley gear
4 driving gear
5 two claws
2 claw
6 base unit
12
HCD-WZ8D
2-12. Pick-up Unit (TDP022W)
6 holder (DBU1)
7 three insulators
1 claw
8 pick-up unit (TDP022W)
2 flexible board
(CN003)
3 wire (flat type)
24p (CN001)
5 three step screws (M)
4 RF board
13
HCD-WZ8D
SECTION 3
TEST MODE
[Cold Reset]
[Disc Tray Lock]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning the
set to the customer.
Procedure:
1. Press three buttons x , EQ EDIT and ?/1 simultaneously.
2. The liquid crystal display does not display any message and the
set is reset.
• The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Setting Procedure :
1. Press the ?/1 button to turn the set on.
2. Set the function to DVD.
3. Press two buttons of x and Z simultaneously for five seconds.
4. The message “LOCKED” is displayed and the tray is locked.
Releasing Procedure :
1. Press two buttons of x and Z simultaneously for five seconds
again.
2. The message “UNLOCKED” is displayed and the tray is
unlocked.
Note :When “LOCKED” is displayed, the tray lock is not released
by turning power on/off with the ?/1 button.
[MD/VIDEO Function Selection Mode]
• This mode is used to select the function of MD or VIDEO.
Procedure:
1. Press the ?/1 button to turn the set on.
2. Press the MD(VIDEO) and ?/1 buttons simultaneously.
3. The function will change from MD to VIDEO, and "VIDEO" is
displayed.
4. To change change back to MD , repeat the same procedure.
[AM Channel Step 9 kHz/10kHz Selection Mode]
• Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Set the function to AM.
2. Turn off the main power.
3. While depressing the x button, press the ?/1 button to turn
on the main power.
4. “AM 9k Step” or “AM 10k Step” is displayed and the channel
step is changed over.
* For E model only
[DVD Ship Mode (without Cold Reset)]
• This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the ?/1 button to turn the set on.
2. Set the function to DVD.
3. Press the x button and the M (Control lever) button
simultaneously.
4. After the "STANDBY" display blinks six times, the message
"LOCK" is displayed on the liquid crystal display, and the DVD
ship mode is set.
[DVD Ship Mode (without Cold Reset)]
• This mode is used to perform the DVD Ship Mode with Cold
Reset.
Procedure:
1. Press the ?/1 button to turn the set on.
2. Set the function to DVD.
3. Press three buttons x , z START (REC PAUSE) and
.m – simultaneously.
4. After the "STANDBY" display blinks six times, the message
"LOCK" is displayed on the liquid crystal display, and the DVD
ship mode is set.
[Color System Selection]
* Color system can be changed to PAL or NTSC.
Procedure:
1. Turn off the main power.
2. Press two buttons X and ?/1 simultaneously.
“COLOR PAL” is displayed and the color system is changed to
PAL. The set is powered on and the function is set to DVD.
3. To change the color system to NTSC, turn off the main power.
4. Press two buttons X and ?/1 simultaneously.
“COLOR NTSC” is displayed and the color system is changed
to NTSC. The set is powered on and the function is set to DVD.
14
[MC Test Mode]
* This mode is used to check operations of the amplifier and tape
deck.
Procedure:
1. Press the ?/1 button to turn the set on.
2. Press three buttons x , z START (REC PAUSE) and MUSIC
MODE simultaneously.
3. “MD” is displayed and dotted lines blink.
4. Every pressing the EQ EDIT button changes the displays in
the order of “GEQ MIN” → “GEQ FLAT” → “GEQ MAX”
5. When the VOLUME control knob is turned clockwise even
slightly, the sound volume increases to its maximum and the
message “VOLUME MAX” appears for two seconds, the display
returns to the original display.
6. When the VOLUME control knob is turned counterclockwise
even slightly, the sound volume decreases to its minimum and
the message “VOLUME MIN” appears for two seconds, the
display returns to the original display.
7. When a tape is inserted in Deck B and by pressing the z START
(REC PAUSE) button recording is started, the input source
function selects MD automatically.
8. During the recording by pressing the .m – button, the
TAPE A/B is selected and tape is rewound. Tape stops at around
the record-starting position and playback of the recorded portion
of the tape is started.
9. Press the ?/1 button to turn the set off.
[GC Test Mode]
• This mode is used to check the software version, key board, VACS
level, liquid crystal display and LEDs.
Procedure:
1. Press three buttons x , z START (REC PAUSE) and
TUNER/BAND simultaneously.
2. Segments of the liquid crystal display and LEDs are all turned
on.
3. To enter the software version display mode, press the .m –
button. The model name and destination are displayed.
4. Each time the .m – button is pressed, the display changes
in the following order. MC, GC, CD, CDD, CDMA, CDMB,
BDA, BDB, ST, TA, TM, TC and MD. Each time the + M >
button is pressed, the contents of the version display change.
5. Press the hH button, and the key check mode is activated.
6. In the key check mode, "K 0 V 0" is displayed. Each time a
button is pressed, "K 0" value increases. However, once a button
is pressed, it is no longer taken into account. "V 0" value
increases like 1, 2, 3 ... if rotaing the VOLUME knob clockwise,
or it decreases like 0, 9, 8 ... if rotating couterclockwise.
7. To exit from this mode, press three buttons in the same manner
as step 1, or disconnect the power cord.
HCD-WZ8D
• VACS Level Display Mode
Procedure:
1. Press three buttons x , z START (REC PAUSE) and
TUNER/BAND simultaneously.
2. Press the X button. The VACS level "VACS 0+0" is displayed.
3. To exit from this mode, press three buttons in the same manner
as step 1, or disconnect the power cord.
• Display Check
Procedure:
1. Press three buttons x , z START (REC PAUSE) and
TUNER/BAND simultaneously.
2. Press the x button and the display changes. Each time the x
button is pressed, the pattern of segments changes.
3. To exit from this mode, press three buttons in the same manner
as step 1, or disconnect the power cord.
DVD OSD Test Mode
[GENERAL DESCRIPTION]
The Test Mode allows you to make diagnosis and adjustment easily
using the remote commander and monitor TV. The instructions,
diagnostic results, etc. are given on the on-screen display (OSD).
[STARTING TEST MODE]
1.
2.
3.
Press the +/1 button to turn the power on, and set the function
to DVD.
While pressing the x and Z button, turn the [VOLUME]
knob clockwise to enter the test mode.
It displays “SERVICE IN” on the liquid crystal display, and
displays the Test Mode Menu on the monitor screen as follows.
(At the bottom of the menu screen, the model name and revision
number are displayed)
[VACS ON/OFF Mode]
• This mode is used to switch on and off the VACS (Variable
Attenuation Control System).
Procedure:
1. Press the ?/1 button to turn the set on.
2. To enter the test mode, press three buttons x , z START
(REC PAUSE) and MOVIE MODE simultaneously.
3. The message "VACS OFF" or "VACS ON" appears.
Test Mode Menu
0.
1.
2.
3.
4.
5.
6.
7.
Syscon Diagnosis
Drive Auto Adjustment
Drive Manual Operation
Mecha Aging
Emergency History
Mecha Error History
Version Information
Video Level Adjustment
Exit: POWER Key
Model
:MHC-WZ8D_6D xx
Revision :x.xx
4.
5.
To execute each function, select the desired menu and press its
number on the remote commander [COMMAND MODE]
(RM-SWZ8D).
To release from test mode, press the +/1 button and turn the
power off.
[OPERATING TEST MODE]
0. SYSCON DIAGNOSIS
The same contents as board detail check by serial interface can be
checked from the remote commander operation.
On the Test Mode Menu screen, press [10/0] key on the remote
commander, and the following Check Menu will be displayed.
### Syscon Diagnosis ###
Check Menu
0.
1.
2.
3.
4.
5.
6.
Quit
All
Version
EEPROM
GPIO
SD Bus
Video
0-0. Quit
Quit the Syscon Diagnosis and return to the Test Mode Menu.
0-1. All (All items continuous check)
This menu checks all diagnostic items continuously. Normally, all
items are checked successively one after another automatically
unless an error is found, but at a certain item that requires judgment
through a visual check to the result, the following screen is displayed
for the key entry.
15
HCD-WZ8D
• Example display
0-2-5. Region
Model destination code is displayed. (2 digits number)
### Syscon Diagnosis ###
Diag All Check
No.2 Version
2-3. ROM Check Sum
Check Sum = xxxx
0-3. EEPROM Check
0-3-1. Sampling Check
EEPROM check at every 64 words.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
0-3-2. Detail Check
EEPROM check at every 1 word.
It compares read data with write data of each address. When
there are discrepancies between two data, it displays error.
Press NEXT Key to Continue
Press PREV Key to Repeat
For the ROM Check, the check sum calculated by the Syscon is
output, and therefore you must compare it with the specified value
for confirmation.
Following the message, press the [NEXT > ] button to go to the
next item, or press the [. PREV] button to repeat the same
operation again.
To quit the diagnosis and return to Check Menu screen, press the
[RETURN] key on the remote commander to display Check Menu.
0-4. GP I/O Check
Pull up/down setting check of the DVD system processor (IC207)
pin 150, 151 and 154 (for clock setting port).
0-5. SD Bus Check
SD bus data check between DVD decoder (IC701) and D-RAM
(IC706).
0-6. Video Check
Output the color bars for video level adjustment.
1.
• Error occurred
If an error occurred, the diagnosis is suspended and error is displayed.
Press the [RETURN] key on the remote commander to quit the
diagnosis, or press the [. PREV] button to repeat the same check
where an error occurred, or press the [NEXT>] button to continue
the check from the item next to faulty item.
General Description of Checking Method
Selecting 2 and subsequent items calls the submenu screen of each
item. And selecting 2 and subsequent items executes respective
menus and outputs the results.
For the contents of each submenu, see “Check Items List” as below.
Check Items List:
0-2.
Version
0-2-1. All
0-2-2. Revision
0-2-3. ROM Check Sum
0-2-4. Model Type
0-2-5. Region
0-3.
EEPROM Check
0-3-1. Sampling Check
0-3-2. Detail Check
0-4.
GP I/O Check
0-5.
SD Bus Check
0-6.
Video Check
0-2. Version
0-2-2. Revision
The revision number of ROM (IC206) that the program for
the DVD system processor (IC207) is stored.
0-2-3. ROM Check Sum
Check sum is calculated.
(4 digits hexadecimal number)
0-2-4. Model Type
Model name is displayed. (MHC-WZ8D)
16
DRIVE AUTO ADJUSTMENT
On the Test Mode Menu screen, press the [1] key on the remote
commander, and the Adjustment Menu will be displayed.
## Drive Auto Adjustment ##
Adjustment Menu
0.
1.
2.
3.
ALL
DVD-SL
CD
DVD-DL
Exit: RETURN
Normally, [10/0] is selected to adjust DVD (single layer), CD and
DVD (dual layer) in this order. But, individual items can be adjusted
for the case where adjustment is suspended due to an error. In this
mode, the adjustment can be made easily through the operation
following the message displayed on the screen.
The disc used for adjustment must be the one specified for
adjustment.
1-0. ALL
Press the [10/0] key on the remote commander, and the servo set
data in EEPROM will be initialized. Then, 1. DVD-SL disc, 2. CD
disc and 3. DVD-DL disc are adjusted in this order.
Each time one disc was adjusted, it is ejected. Replace it with the
specified disc following the message. You can finish the adjustment
by pressing the [RETURN] button on the remote commander.
Note: During adjustment of each disc, the measurement for disc type judgment is made. As automatic adjustment does not judge the disc
type unlike conventional models, take care not to insert wrong type
discs. Also, do not give a shock during adjustment.
HCD-WZ8D
1-1. DVD-SL (single layer)
Press the [1] key on the remote commander and insert a DVD single
layer disc following the message. Then the adjustment will be made
through the steps below, then adjusted values will be written to the
EEPROM.
DVD Single Layer Disc Adjustment Steps:
1. Sled tilt reset
2. Disc check memory SL
3. Wait 300 msec
4. Set disc type SL
5. LD on
6. Spindle start
7. Wait 1 sec
8. Focus servo on 0
9. Auto track offset adjust
10. CLVA on
11. Wait 500 msec
12. Tracking on
13. Wait 1 sec
14. Sled on
15. Check CLV on
16. Auto LFO adjust
17. Auto focus offset adjust
18. Auto tilt position adjust
19. Auto focus gain adjust
20. Auto focus offset adjust
21. EQ boost adjust
22. Auto loop filter offset adjust
23. Auto track gain adjust
Search Check
24. 32 track jump forward
25. 32 track jump reverse
26. 500 track jump forward
27. 500 track jump reverse
28.All servo stop
29.EEP copy loop filter offset
1-2. CD
Press the [2] key on the remote commander and insert a CD disc
following the message. Then the adjustment will be made through
the steps below, then adjusted values will be written to the EEPROM.
CD Adjustment Steps
1. Sled tilt rest
2. Disc check memory CD
3. Wait 500 msec
4. Set disc type CD
5. LD on
6. Spindle start
7. Wait 500 msec
8. Focus servo on 0
9. Auto track offset adjust
10. CLVA on
11. Wait 500 msec
12. Tracking on
13. (TC display start)
14. Wait 1 sec
15. Jitter display start
16. Sled ON
17. Check CLV on
18. Auto loop filter offset adjust
19. Auto focus offset adjust
20. Auto focus gain adjust
21. Auto focus offset adjust
22. EQ boost adjust
23. Auto LFO Adjust
24. Auto track gain adjust
Search Check
25. 32Tj forward
26. 32Tj reverse
27. 500Tj forward
28. 500Tj reverse
29. All servo stop
1-3. DVD-DL (dual layer)
Press the [3] key on the remote commander and insert a DVD dual
layer disc following the message. Then the adjustment will be made
through the steps below, then adjusted values will be written to the
EEPROM.
DVD Dual Layer Disc Adjustment Steps:
1. Sled tilt reset
2. Disc check memory DL
3. Wait 500 msec
4. Set disc type DL
5. LD on
6. Spindle start
7. Wait 1 sec
Layer 1 Adjust
8. Focus servo on 0
9. Auto track offset adjust
10. CLVA on
11. Wait 500 msec
12. Tracking on
13. Wait 500 msec
14. Sled on
15. Check CLV lock
16. Auto loop filter offset adjust, Auto focus adjust
17. Auto focus gain adjust
18. Auto focus offset adjust
19. EQ boost adjust
20. Auto loop filter offset adjust
21. Auto Track Gain Adjust
Search Check
22. 32 track jump forward
23. 32 track jump reverse
24. 500 track jump forward
25. 500 track jump reverse
Layer 0 Adjust
26. Focus jump (L1 t L0)
27. Auto track offset adjust L0
28. CLVA on
29. Wait 500 msec
30. Tracking on
31. Wait 500 msec
32. Sled on
33. Check CLV lock
34. Auto focus filter offset adjust
35. Auto Focus Adjust
36. Auto focus gain adjust
37. Auto focus offset adjust
38. EQ boost adjust
39. Auto Loop Filter Offset
40. Auto track gain adjust
Search Check
41. 32 track jump forward
42. 32 track jump reverse
43. 500 track jump forward
44. 500 track jump reverse
Layer Jump Check
45. Layer jump (L0 ? L1)
46. Layer jump (L1 ? L0)
47. All servo stop
17
HCD-WZ8D
2.
DRIVE MANUAL OPERATION
2-1. Disc Type
Note: This mode is used for design, and not used in service fundamentally.
On the Test Mode Menu screen, press the [2] key on the remote
commander, and the Operation Menu will be displayed. For the
manual operation, each servo on/off control and adjustment can be
executed manually.
## Drive Manual Operation ##
Operation Menu
1. Disc Type
2. Servo Control
3. Track/Layer Jump
4. Non EEPROM Write Adjust
5. EEPROM Write Adjust
6. Memory Check
7. Disc Check Memory
8. Error Rate Display
9. SACD Water Mark
Exit: RETURN
In using the manual operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is displayed
when a disc is loaded.
Note:
1. Set correctly the disc type to be used on the Disc Type screen.
2. In case of an alarm, immediately press the x button to stop the
servo operation, and press the +/1 button to turn the power
off.
Basic operation:
(controllable from front panel or remote commander)
+/1
: Power OFF (release the Test Mode)
x
: Servo stop
Z
: Stop and eject/Loading
[RETURN]
: Return to Operation Menu or Test
Mode Menu
[. PREV], [NEXT>] : Transition between sub modes of menu
[1] to [9], [10/0]
: Selection of menu items
Cursor o / O
: Increase/Decrease in manually
adjusted value
Disc Type
Disc Type Select
1.
2.
3.
4.
Disc Type Auto Check
Set Disc Type DVD
Set Disc Type CD
Set Disc Type Hybrid
Exit: RETURN
2-1-1. Disc Type Auto Check
1) Press the [1] key on the remote commander to display the Disc
Type Auto Check screen.
2) Insert a disc and press the [ENTER] key on the remote
commander.
3) It judges the type of inserted disc automatically and displays
the disc type and so on as below.
Disc Type Auto Check
Disc Type
Layer
Mirr Time
Mirr Count
FZC Count
PI Reference
PI Peak
xx
xx
xx
xx
xx
xx
xx
ENTER.Execute
Exit: RETURN
Disc Type
Layer
Mirr Time
: CD, DVD or Hybrid (SACD)
: SINGLE, DUAL or HYBRID
: Mirror time of between disc surface and record
surface when disc type judgment. (hexadecimal
number)
Mirr Count : The number of times which mirror counts between
disc surface and record surface when disc type
judging.
FZC Count : The number of times which focus zero cross points
of each layer when lens down.
PI Reference : The average of PI reference voltage. (hexadecimal
number)
PI Peak
: PI peak level voltage. It performs only when disc
type judgment is successful. (hexadecimal number)
2-1-2. Disc Type DVD
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]: DVD single layer disc (12 cm)
[2]: DVD dual layer disc (0 layer, 12 cm)
[3]: DVD dual layer disc (1 layer, 12 cm)
[4]: DVD-RW disc (12 cm)
[5]: DVD single layer disc (8 cm)
[6]: DVD dual layer disc (0 layer, 8 cm)
[7]: DVD dual layer disc (1 layer, 8 cm)
[8]: DVD-RW disc (8 cm)
18
HCD-WZ8D
2-1-3. Disc Type CD
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]: CD disc (normal speed, 12 cm)
[2]: CD disc (double speed, 12 cm)
[3]: CD disc (normal speed, 8 cm)
[4]: CD disc (double speed, 8 cm)
[5]: CD-RW disc (normal speed, 12 cm)
[6]: CD-RW disc (double speed, 12 cm)
[7]: CD-RW disc (normal speed, 8 cm)
[8]: CD-RW disc (double speed, 8 cm)
2-1-4. Disc Type Hybrid
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
[1]: SACD Hybrid disc (SACD layer, 12 cm)
[2]: SACD Hybrid disc (CD layer, normal speed, 12 cm)
[3]: SACD Hybrid disc (CD layer, double speed, 12 cm)
[4]: SACD Hybrid disc (SACD layer, 8 cm)
[5]: SACD Hybrid disc (CD layer, normal speed, 8 cm)
[6]: SACD Hybrid disc (CD layer, double speed, 8 cm)
2-2. Servo Control
Note: Be sure to perform the disc type setup before performing this item.
Servo Control
1.LD
off R.Sled
2.Focus
off L.Sled
3.SPDL
off U.Sled
4.CLVA
off D.Sled
5.Trk.
off
6.Sled
off
7.Fcs.Srch
off
FWD
REV
Reset
Limit
0.All Servo Off
Exit: RETURN
On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system is
faulty or RF is not present. In such a case, do not operate CLVA.
[1] LD
: Turn on/off the laser.
[2] Focus
: Search the focus and turn on the focus.
[3] SPDL
: Turn on/off the spindle.
[4] CLVA
: Turn on/off normal servo of spindle servo.
[5] Trk.
: Turn on/off the tracking servo.
[6] Sled
: Turn on/off the sled servo.
[7] FCS. Srch : Turn on/off the focus search.
[10/0]
: All servo off.
[R] Sled FWD (right cursor) : Move the sled forward.
[L] Sled REV (left cursor) : Move the sled reverse.
[U] Sled FWD (up cursor) : Reset the sled.
[D] Sled REV (down cursor) : Limit in the sled.
2-3. Track/Layer Jump
1. 1Tj
2. 1Tj
3.500Tj
4.500Tj
5.10kTj
6.10kTj
7.20kTj
8.20kTj
Track/Layer Jump
FWD
REV
Fine
FWD
Fine
REV
Dirc
FWD
Dirc
REV
Dirc
FWD
Dirc
REV
0. All Servo Off
Exit: RETURN
On this screen, track jump, etc. can be performed. Only for the DVD
dual layer disc, the focus jump and layer jump are displayed in the
right field
[1] 1Tj FWD : 1 track jump forward.
[2] 1Tj REV : 1 track jump reverse.
[3] 500Tj FWD: 500 track jump (fine search)forward.
[4] 500Tj REV : 500 track jump (fine search) reverse.
[5] 10kTj FWD: 10k track jump (direct search) forward.
[6] 10kTj REV : 10k track jump (direct search) reverse.
[7] 20kTj FWD: 20k track jump (direct search) forward.
[8] 20kTj REV : 20k track jump (direct search) reverse.
[10/0]
: All servo off.
2-4. Non EEPROM Write Adjust
Non EEPROM Write Adjust
1.
2.
3.
4.
5.
6.
Focus
Focus
Trk.
Trk.
Trk.
EQ
Offset
Gain
Offset Coarse
Offset Fine
Gain
Boost
0.All Servo Off
Exit: RETURN
On this screen, each item can be adjusted manually. Select the desired
number [1] to [10/0] from the remote commander, and current
setting for the selected item will be displayed, then increase or
decrease numeric value with the O key or o key. This value is
stored in the EEPROM. If CLV has been applied, the jitter is
displayed for reference for the adjustment.
[1] Focus Offset : Adjusts focus offset.
[2] Focus Gain : Adjusts focus gain.
[3] TRK. Offset : Adjusts tracking offset of the RF amp
(IC001) side.
[4] TRK. Offset : Adjusts tracking offset of the DSP (IC401)
side.
[5] TRK. Gain : Adjusts track gain.
[6] EQ Boost : Adjusts amount of boost of equalizer.
[10/0]
: All servo off.
19
HCD-WZ8D
2-5. EEPROM Write Adjust
2-7. Disc Check Memory
EEPROM Write Adjust
1.
2.
3.
4.
5.
6.
Focus
Focus
Trk.
——————
Trk.
EQ
Offset
Gain
Offset Coarse
Disc Check Memory
1. SL Disc check
2. CD Disc check
3. DL Disc check
Gain
Boost
0.All Servo Off
Exit: RETURN
On this screen, each item can be adjusted automatically. Select the
desired number [1] to [10/0] from the remote commander, and
selected item is adjusted automatically.
Exit: RETURN
On this screen, measure the mirror time of chucked disc, and write
to the EEPROM.
2-8. Error Rate Display
[1] Focus Offset : Adjusts focus offset.
[2] Focus Gain : Adjusts focus gain.
[3] TRK. Offset : Adjusts tracking offset of the RF amp
(IC001) side.
[5] TRK. Gain : Adjusts track gain.
[6] EQ Boost : Adjusts amount of boost of equalizer.
[10/0]
: All servo off.
2-6. Memory Check
Display images are shown as follows, and all two screens are able
to switch by the O key (UP) or o key (DW).
EEPROM Data 1/2
CD
Focus Gain
xx
Trk.
Gain
xx
Focus Offset
xx
Trk.
Offset
xx
EQ.
Boost
xx
PI
Level
xx
Fcs. Balance
-Jitter
xx
Mirror Time
xx
FE Level
-Traverse Lv1.
-Next:DW Default:CLR
EEPROM
Focus
Trk.
Focus
Trk.
EQ.
Data 2/2
Gain
Gain
Offset
Offset
Boost
SL L0 L1
xx xx xx
xx xx xx
xx xx xx
xx xx xx
xx xx xx
xx -- -xx -- -xx xx xx
xx xx -xx -- -xx -- -Exit:RET
CDRW DVDRW
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
Error Rate Display
UC
CR ADD
PI1 Err Now xx xxxx xxxxxxxx
Max xx xxxx xxxxxxxx
Avg xx xxxx xxxxxxxx
PI2 Err Now xx xxxx xxxxxxxx
Max xx xxxx xxxxxxxx
Avg xx xxxx xxxxxxxx
PO Err Now xx xxxx xxxxxxxx
Max xx xxxx xxxxxxxx
Avg xx xxxx xxxxxxxx
Exit: RETURN
On this screen, measure and display the error rate.
UC : Incorrect value
CR : Correct value
Add : Address
2-9. SACD Water Mark Check (Not used)
SACD Water Mark Check
PSP AMP
PSN
Start: ENTER
Stop: RETURN
On this screen, measure the PSP AMP value and PSN value of SACD
water mark.
Prev:UP Default:CLR
Exit:RET
On this screen, current servo adjusted data stored in the EEPROM
are displayed. The adjusted data are initialized by pressing the
[CLEAR] key, but be careful that they are not recoverable after
initialization.
Before clearing the adjusted data, make a note of the set data. This
screen will also appear if [0]-All is selected in the Drive Auto
Adjustment. In this case, default setting cannot be made.
20
HCD-WZ8D
3.
MECHA AGING
On the Test Mode Menu screen, selecting [3] executes the aging of
the mechanism deck.
**
### Aging Test MENU ###
Pls use over 40min. CD **
Operation Menu
1. Open/Close Test
Exit: RETURN
1)
2)
3)
On the Aging Test MENU screen, press the [1] key on the
remote commander to display the Open/Close Test screen.
Insert discs and press the [ENTER] key on the remote
commander.
Is starts the aging.
During aging, the disc number, operating status and repeat cycle
are displayed. Aging can be aborted at any time by pressing
the [RETURN] key. After the operation is stopped, press the
[RETURN] key to return to the Aging Test MENU.
• Code list of Emergency History
10: Communication to RF AMP (IC001) failed.
11: Each servo for focus, tracking, and spindle is unlocked.
12: Check sum error of EEPROM (IC204).
14: Communication to servo DSP (IC509) failed, or servo DSP
(IC509) is faulty.
15: Communication to DVD decoder (IC701) failed, or DVD
decoder (IC701) is faulty.
16: Communication to DSD decoder (IC801) failed, or DSD
decoder (IC801) is faulty. (Not used)
20: Initialization of sled servo failed. It is not placed in the initial position.
23: Sled servo operation error.
24: Made a request to move the sled servo to wrong position.
30: Tracking balance adjustment error.
31: Tracking gain adjustment error.
33: Focus bias adjustment error.
34: Focus gain adjustment error.
35: Equalizer adjustment error.
40: Focus servo does not operate.
41: With a DVD dual layer disc, focus jump failed.
50: CLV (spindle) servo does not operate.
51: Spindle does not stop.
60: Made a request to seek nonexistent address.
61: Seek error of retry more than regulated times.
70: Control data could not be read.
80: Disc reading failed.
5.
4.
EMERGENCY HISTORY
On the Test Mode Menu screen, selecting [4] displays the
information such as servo emergency history.
The history information from last 1 up to 10 can be scrolled with
the O key or o key. Also, specific information can be displayed
by directly entering that number with ten keys.
MECHA ERROR HISTORY
On the Test Mode Menu screen, selecting [5] displays the information
of mechanism deck error history.
The history information from last 1 up to 8 can be scrolled with
the O key or o key. Also, specific information can be displayed
by directly entering that number with ten keys.
### Mecha Error History ###
### EMG. History ###
Laser Hours
CD xxxxhxxm
DVD xxxxhxxm
a.
bb xx xx xx
xx xx xx xx
xx xx xx xx
xx xx xx xx
a.
bb xx xx xx
xx xx xx xx
xx xx xx xx
xx xx xx xx
Select:1-9
(1.Latest EMG.)
Scroll:UP/DOWN
Exit: RETURN
1.
2.
3.
4.
5.
6.
7.
8.
aa
aa
aa
aa
aa
aa
aa
aa
bb
bb
bb
bb
bb
bb
bb
bb
cc
cc
cc
cc
cc
cc
cc
cc
xx
xx
xx
xx
xx
xx
xx
xx
(1.Latest Err.)
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
xx
Scroll:UP/DOWN
Exit: RETURN
xxxxhxxm : The laser on total hours. Data below minutes are
omitted.
a.
: Error number.
bb
: Error code.
xx
: Not used.
• Clearing History Information
Clearing laser hours:
Press the [DVD DISPLAY] and [CLEAR] keys in this order.
Then both CD and DVD data are cleared.
Clearing emergency history:
Press the [DVD TOP MENU] and [CLEAR] keys in this order.
Initializing set up data:
Press [DVD MENU] and [CLEAR] keys in this order.
The data have been initialized when “Set Up Initialized”
message is displayed. The EMG. History screen will be restored
soon.
21
HCD-WZ8D
aa: Initialization is completed or not.
FF
: Complete.
other number : Not complete.
bb: Operating status of mechanism deck at an error occurred.
(lod sq jcp)
00
: Initializing.
10 to 15 : Open operating.
16 to 19 : Kicking cause open failed.
1A to 1F : Open operating.
20 to 27 : Complete the open operation.
28
: No disc and complete the open operation.
29 to 2F : Complete the open operation.
30 to 3F : Close requesting.
40 to 4F : Open requesting.
50 to 5F : Close operating.
60 to 6F : Complete the chucking operation.
80 to 8F : Complete the release operation.
(BU is home position)
90 to 9F : BU down operating.
A0 to AF : Opening/closing the shutter. Or stationary state in
open/close the shutter is enablement.
B0 to BF : BU up requesting.
C0 to CF : BU down requesting.
D0 to DF : BU upping.
E0 to EF : No disc checking in disc loading.
cc: Operating status of mechanism deck at an error occurred.
(lod oq jcp)
00
: Complete the operation.
10 to 1F : Open operating.
20 to 2F : Close operating.
30 to 3F : Release operating.
60 to 6F : Chucking operating.
70 to 7F : Kicking operating.
80 to 8F : Returning the BU to home position. (after kicking)
22
6.
VERSION INFORMATION
On the Test Mode Menu screen, selecting [6] displays the ROM
version and region code.
The parenthesized hexadecimal number in version field is checksum
value of ROM.
## Version Information ##
IF con.
Ver.x. xx
SYScon.
Ver.x.
Model
Region
Config
xx (xxxx)
MHC-WZ8D_6D
0x
xxxxxxxx
Front End Ver.x.xx
Exit: RETURN
IF con. : The version of system controller (IC501).
SYScon. : The version of DVD system processor (IC207).
Front End: The version of mechanism controller (IC901).
7.
VIDEO LEVEL ADJUSTMENT
On the Test Mode Menu screen, selecting [7] displays color bars
for video level adjustment. During display of color bars, OSD
disappears but the menu screen will be restored if pressing the
[RETURN] key.
HCD-WZ8D
SECTION 4
DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
¢
•
: internal component
• 2 : nonflammable resistor
• 5 : fusible resistor
• C : panel designation
Circuit Boards Location
MAIN board
REGULATOR board
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
Note on Printed Wiring Boards:
• X : parts extracted from the component side
• Y : parts extracted from the conductor side
• b : Pattern from the side which enables seeing
Caution:
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Parts on the pattern face side seen from
the pattern face are indicated
Parts on the parts face side seen from
the parts face are indicated
• Indication of transistor
C
•
•
•
•
BACK LIGHT board
•
CD-TC SW board
ENTER-SW board
•
PANEL board
•
•
•
RF board
4CH-VOL board
MS-128 board
LCD board
VIDEO board
•
MIC board
DMB03 board
HP AMP board
23
A : B+ Line
B : B– Line
H : adjustment for repair
Power voltage is fed with DXA-WZ8D from external connector (SYSTEM CONTROL 1, 2).
Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
Circled numbers refer to waveforms.
Signal path
F : AUDIO
L : VIDEO
E : PB (TAPE)
a : REC (TAPE)
J : CD
c : DVD
d : TUNER
h : MD
N :Y
O : CHROMA
P : COMPONENT VIDEO
Abbreviation
AUS : Australian model
E2
: 120V AC area in E model
E3
: 240V AC area in E model
E15 : 220-240V AC area in E model
EA
: Saudi Arabia model
KR
: Korean model
MY
: Malaysia model
PH
: Philippines model
RU
: Russian model
SP
: Singapore model
TH
: Thai model
23
These are omitted.
Q
B E
Q
B C
E
These are omitted.
Q
B
C
E
These are omitted.
HCD-WZ8D
• Waveforms
-RF Board-
1 IC001 1 (DVDRFP)
2 IC001 el (TE)
3 IC001 r; (FE)
4 IC001 tj (RFAC)
0.3 Vp-p
0.5 Vp-p
800 mVp-p
200 mV/DIV, 100 ns/DIV
1.3 Vp-p
500 mV/DIV, 100 ns/DIV
100 mV/DIV, 1 ms/DIV
500 mV/DIV, 1 ms/DIV
-DMB03 Board-
5 IC906 8 (XTO)
7 IC906 q; (SO2)
4.2 Vp-p
8 IC906 qd (SO3)
1 V/DIV, 10 ns/DIV
29.5 ns
1 V/DIV, 10 ns/DIV
q; IC901 r; (XTAL)
37 ns
1 V/DIV, 10 ns/DIV
qa IC207 <zcz (VDAC 0)
5.1 Vp-p
4.3 Vp-p
4.5 Vp-p
29.5 ns
37 ns
9 IC906 3 (MO1)
1 V/DIV, 10 ns/DIV
qs IC207 <zx, (VDAC 1)
qd IC207 <zxb (VDAC 2)
1.3 Vp-p
1.1 Vp-p
3.6 Vp-p
50 ns
H
H
500 mV/DIV, 20 µs/DIV
1 V/DIV, 20 ns/DIV
qf IC207 <zxx (VDAC 3)
990 mVp-p
200 mV/DIV, 20 µs/DIV
200 mV/DIV, 20 µs/DIV
qg IC207 <zz. (VDAC 4)
H
qh IC601 <zc. (MCLK2)
790 mVp-p
3.3 Vp-p
H
820 mVp-p
H
200 mV/DIV, 20 µs/DIV
200 mV/DIV, 20 µs/DIV
82 ns
1 V/DIV, 40 ns/DIV
-MAIN Board-
qj IC401 qa (XC-OUT)
qk IC401 qd (X-OUT)
3.1 Vp-p
2.6 Vp-p
62.5 ns
30.5 µs
1 V/DIV, 10 µs/DIV
1 V/DIV, 20 ns/DIV
-VIDEO Board-
ql IC801 qk(CROUTA)
w; IC801 wa(CBOUTA)
wa IC801 wf (CYOUTA)
1.5 Vp-p
H
500 mV/DIV, 20 µs/DIV
1.5 Vp-p
wd IC801 wj (Y OUTA)
H
H
500 mV/DIV, 20 µs/DIV
ws IC801 e; (V OUTA)
2.6 Vp-p
2.1 Vp-p
500 mV/DIV, 20 µs/DIV
H
500 mV/DIV, 20 µs/DIV
wf IC801 ed (C OUT)
2.1 Vp-p
H
500 mV/DIV, 20 µs/DIV
H
1.9 Vp-p
500 mV/DIV, 20 µs/DIV
24
24
HCD-WZ8D
4–1. Block Diagrams – RF Servo Section –
AEP, UK, RU, AUS
CD_DOUT
A
VIDEO
SECTION
B
VIDEO
SECTION
C
VIDEO
SECTION
D
VIDEO
SECTION
E
VIDEO
SECTION
HDB0 – HDB7
DOUT 64
50 RFAC
PCMD 66
36
37
FOCUS COIL
DRIVE
48
1
TRACKING COIL
DRIVE
3
4
FF
FR
FF
FR
TF
TR
FF
FR
M1
(SPINDLE)
M
27
28
47
46
SPINDLE MOTOR
DRIVE
BUFFER
RFDC
26 SCOR
DATA 4
CLOK 6
XLAT 5
SENS 7
SQSO 76
SQCK 77
49
50
27
9
52
54
XRST
2
LOCK 24
GFS 13
MUTE 3
XTO
98 XDRST
75 LOCK_CD
71 GFS_CD
59 MUTE_CD
33 FFDR
34 FRDR
IC503
AMP
SLED 61
17
18
19
20
21
XRD
XWR
XCS
XINT0
XINT1
XMWR
XMOE
XRAS
XCAS
17
33
18
34
35
WE
OE
RAS
UCAS
LCAS
IC706
16Mbit
D-RAM
76
94
78
95
107 GFS
XRST_1882 25
164 XRST
109 92
53
27M
31 TFDR
32 TRDR
7 FCS_JMP_1
8 FCS_JMP_2
44 SLED_B
43 SLED_A
85
84
12
22
23
XRD
XWR
XCS_DVD
INIT0_DVD
INIT1_DVD
I/O0 – I/O15
XTI
DATA_CD
CLOK_CD
LAT_CD
SENS_CD
SQSO
SQCK
GFS_DVD 58
COUT 19
SCLK 8
FOK 22
MIRR 20
29 SFDR
30 SRDR
30
72
74
29
COUT_CD
SCLK_CD
FOK_CD
MIRR
SCK_DSD 45
JIT 64
IC703 (1/2)
COMPARATOR
XSRQ-ZIVA
10
39
19
20
21
22
97 A8
60 MUTE_2D
63 SP_ON
73 TSD-M
13
45
62 FG
MIRR
MNT1
TE
FE
PI
POWER SAVE
MUTE12
MUTE34
MUTE5
TSD-M
TF
TR
83 82 2
65 67 66
TE
FE
PI
SLED MOTOR
DRIVE
7
31
DATA_RF
CLK_RF
SDEN
SLED MOTOR
DRIVE
76 28
SDATA_RF
SDCLK_RF
SDEN
M
32
31
30
29
TE
SE
FE
SCOR 15
38 VC
42 CE
INLIM
40
34
35
M2
(SLED)
3 DOCTRL/
ISBTEST
A0 – A9
AVC
(1.65V)
BUFFER
41
40
39
43
FE
PI
LDSEL
LD_ON
TRK+
TRK–
TE
42
137 MDIN2
135 SPO
2-5, 7-10,
41-44, 46-49
26 SSTP
INLIM
FCS+
FCS–
IC703 (2/2)
BUFFER
21 DVDLD
IC501
FOCUS/TRACKING COIL DRIVER,
SPINDLE, SLED MOTOR DRIVER
167 XTAL
169 XTL2
170 XTL1
172-176, 1, 2, 4
MD2 63
MIRR
MIRR 27
Q901
LASER DIODE
SELECT
IC701
DVD DECODER
TE
FE
PI
TE 39
FE 40
MNTR 42
36 V125
2AXIS
DEVICE
FOCUS/
TRACKING
COIL
10
MDP 25
LDON 26
SW
3
WFCK
SBIN
EXCK
SCOR
XDCK, XSAK, SDEF
XDCK
XSAK
SDEF
XHWR 48
HDRQ 46
HDB8 26
21-24,
27-32
22 CDLD
8
13
XTAI 71
DATA_RF
CLK_RF
SDEN
SDATA 47
SCLK 46
SDEN 48
24 CDPD
23 DVDPD
Q001
AUTOMATIC POWER
CONTROL (FOR DVD)
IC906
CLOCK
GENERATOR
7
151
148
147
150
A0 – A7
LASER
DVD LD
DIODE
(FOR DVD)
X902
27MHz
BCLK
LRCK
C2PO
GSCOR
5, 7, 9-14
PD
CD A
CD B
CD C
CD D
WFCK
SBSO
EXCK
SCOR
D0 – D7
14-21
Q002
AUTOMATIC POWER
CONTROL (FOR CD)
16
15
14
13
IC509
CD DECODER,
DIGITAL SERVO PROCESSOR
IC001
CD/DVD/SACD RF AMP,
FOCUS/TRACKING ERROR AMP
WFCK
SBSO
EXCK
SCOR
158
163
155
146
A0 – A7
89-96
CD LD
B
A
D
C
A
B
C
D
BCLK
LRCK
C2PO
GSCOR
SO2
OPTICAL PICK-UP
BLOCK
(TDP022W)
12
11
10
9
BCLK
LRCK
C2PO
GSCOR
MO1
17 CD F
B
A
D
C
LASER
DIODE
(FOR CD)
WFCK 10
SBSO 79
EXCK 80
18 CD E
E
67
65
14
17
SO3
F
BCK
LRCK
C2PO
WDCK
A2
B2
C2
D2
27M
3
4
5
6
D
C
B
A
DETECTOR
A
B
C
D
160 MDAT
66-69, 71, 73-75, 96, 97,
99, 101, 102, 104-106
RFAC 57
SD0 – SD7
8
79, 80, 82-87,
89, 91
55 DIN
MDB0 – MDB9,
MDBA – MDBF
54 DIP
FNN 52
MA0 – MA9
FNP 53
60 AIN
XHAC
59 AIP
APE0
ATOP 62
ATON 61
MNT1
1 DVDRFP
63 RFSIN
D0 – D7
RF
44, 41, 39, 35,
32, 30, 27, 24
117 RFIN
6
SDA_EEP 5
SCL_EEP 100
WP_EEP 99
5 SDA
6 SCL
7 WP
IC903
EEPROM
• SIGNAL PATH
IC901 (1/2)
MECHANISM
CONTROLLER
25
25
: CD
: AUDIO
: DVD
: VIDEO
HCD-WZ8D
8
B
SD0
SD1
SD2
SD3
SD4
SD5
SD6
SD7
IC256
D-FF
AV0
AV1
AV2
AV3
AV4
AV5
AV6
AV7
IC801
VIDEO AMP, 75Ω DRIVER
SDDATA0 – SDDATA7
RF SERVO
SECTION
177-174, 171-168
– Video Section –
V
VDAC_0 131
V OUTA 30
V OUTB 31
4 V IN
J802
VOUT
VIDEO OUT
• SIGNAL PATH
C
VDAC_1 128
2 C IN
C
C OUT 33
: AUDIO
Q801,802
WIDE SWITCH
4
3
2
J801
S VIDEO OUT
1
: VIDEO
:Y
3
C
XSAK
SDEF
XDCK
6 Y IN
XSAK#
179 SDEN
SDEF#
182 SDERROR
XDCK#
183 SDCLK
IC258
D-FF
Y/G
VDAC_2 125
CB/R
VDAC_3 122
192 INT/EXT
AUDIO
SECTION
4
F
BCK
LRCK
14 CB IN
CR/B
VDAC_4 119
ADC_DATA
CY OUTA
CY OUTB
CB OUTA
CB OUTB
CR OUTA
CR OUTB
12 CY IN
MUTE1
MUTE2
RF SERVO
SECTION
: CHROMA
Y OUTA 27
Y OUTB 28
16 CR IN
IC255
IC259
D-FF
Y
: COMPONENT VIDEO
24
25
21
22
18
19
CYOUT
Y
J803
CBOUT
COMPONENT
VIDEO OUT
PB/CB
CROUT
PR/CR
3 15
V-MUTE1, V-MUTE2
V-MUTE2
V-MUTE1
K
AUDIO
SECTION
AEP, UK,RU, AUS
RF SERVO
SECTION
A
CD_DOUT
157 DAI_DATA
LRCK-ZIVA
BCK-ZIVA
XCK
DATA0
DATA1
148
149
147
150
151
152
153
DATA2
DATA3
161 160
186 187 185 184
188
116 165
162
191
IC207
DVD SYSTEM PROCESSOR
HAD0 – HAD15
22, 19-14, 11-3
HAD0 – HAD15
HA1 – HA3
2, 207, 206
190
195 27 25
MD0 – MD31
MA0 – MA11
42-33, 45, 46 48 47
57-60, 64-71, 75-78,
81-84, 88-95, 99-102
MCLK
MCS0
MWE
MRAS
MCAS
MDQM0
MDQM1
MDQM2
MDQM3
143 MDI
144 MC
145 ML
BA0
BA1
MDI
MC
ML
HCS0
HREAD
WEN.UDS
MDI, MC, ML
202 RESET
110 MREQ
56 49 53 51 52 62 73 86 97
CE
OE
WE
I
SYS RESET
MUTE REQ
VS
AUDIO
SECTION
SYS RESET, MUTE REQ
107
ALE
H
109
178 SDREQ
RST_SPC
AUDIO
SECTION
139 XIN
XSRQ_ZIVA
CDSEL
E
DVD DIGITAL
OUT OPTICAL
6
CS_(ZIVA_E2P)
RE SERVO
SECTION
27M
OPTICAL
OUT
5
HIRQ2
D
ICE958 156
DRVRDY
RE SERVO
SECTION
LRCK
BCK
XCK
DATA0(DM)
DATA1(FLR)
DATA2(SLR)
DATA3(CSW)
DRVTX
DRVRX
DRVCLK
HIRQ1
7
G
IC201
I2C_DA
I2C_CL
AUDIO
SECTION
IC252
2
1
HA1 – HA3
1 8 3
IC904
FLIP-FLOP
DQ0 – DQ31
55, 54, 52, 51,
49-47, 45-40, 38-36
1D1 – 1D10, 2D1 – 2D6
Q202
34, 33, 31
2D7 – 2D9
67
1Q1 – 1Q10, 2Q1 – 2Q9
38
RST
IC901 (2/2)
MECHANISM CONTROLLER
41
DATA & ADDRESS BUS
HAD0 – HAD15
HA1 –
HA3
29,31,33,35,38,40,42,44,
30,32,34,36,39,41,43,45
DQ0 – DQ15
40
25-23
A0 – A2
22-18, 9-1, 48,
17, 16, 9, 10, 13
A3 – A21
IC206
PROGRAMMABLE ROM
X901
20MHz
26
26
CE
OE
WE
32
26 28 11
CE
OE
WE
37
ADDRESS BUS
HA4 –HA22
34 33 35 36
CS_ZIVA
2, 3, 5, 6, 8-10, 12-17,
19-21, 23, 24, 26
78 79
A0 – A11
56 29
IC216
BUS INTERFACE
IC902
SWITCHING
25-27,
22 23
60-66,24,21
IC203
128Mbit SD-RAM
68 20 17 19 18 16 71 28 59
CLK
CS
WE
RAS
CAS
DQM0
DQM1
DQM2
DQM3
2,4,5,7,8,10,11,13,74,76,77,79,80,82,83,85,31,
33,34,36,37,39,40,42,45,47,48,50,51,53,54,56
HA1 – HA3
CKE
IC204
EEPROM
HAD0 – HAD15
1LE
2LE
Q903
SWITCH
BS0
BS1
R/B
WC
CS
DATA & ADDRESS BUS
6 DO
5 DI
4 SK
DRVRDY
I2CCLK
Q904
SWITCH
SO_ZIVA
SI_ZIVA
SCK_ZIVA
DRVIRQ
I2CDATA
XTAL
I2CDATA, I2CCLK
I2C_SIO
I2C_SCL
J
EXTAL
MAIN
SECTION
HCD-WZ8D
– Audio Section –
AEP, UK, RU, E2
7
G
IC302
D/A CONVERTER
EXCEPT AEP, UK, RU, E2
IC601
DSP
VIDEO
SECTION
G
7
DATA0
DATA1
DATA2
DATA3
LRCK-ZIVA
BCK-ZIVA
XCK
39
27
28
35
29
38
62
SDI4
SDI1
SDI2
SDI3
LRCKI1
BCKI1
KSIO
DATA0 (DMX-B)
DATA1 (FLR-B)
SDO4 26
FLR-B
SDO1 60
SDO2 61
SDO3 25
LRCKO 63
BCKO 64
SCKOUT 10
DATA2 (SLR-B)
DATA3 (CSW-B)
LRCK-ZIVA (LRCK-B)
BCK-ZIVA (BCK-B)
XCK (MCK-B)
DMX-B
SLR-B
CSW-B
31
45
46
47
41
40
38
DATA4
DATA1
DATA2
DATA3
LRCK
BCK
SCKI
VOUT1 14
VOUT2 13
VOUT3 12
LRCK-B
BCK-B
MCK-B
VIDEO
SECTION
MDI
MC
ML
I
VOUT4 11
34 MDI
35 MC
36 ML
VOUT5 10
D0 – D15
VOUT8 20
HDIN
HCLK
HCS
EXLOCK
PM
BST
XRST
FL
FL-OUT 34
Q304
MUTE
FR
2 FR-IN
FR-OUT 32
6 SL-IN
SL-OUT 29
10 SR-IN
SR-OUT 26
REAR-L
SR
Q308
MUTE
C
MAIN
SECTION
DXA-WZ8D (1/3)
SL
Q307
MUTE
SR
M
FR
Q305
MUTE
SL
REAR-R
DVD MUTE
13 C-IN
C
C-OUT 25
DVD MUTE
CENTER
Q306
MUTE
SW
14 LFE-IN
DOWNMIX-L
L-OUT 38
Q309
MUTE
DM_L
N
37 DM-L
DOWNMIX-R
R-OUT 39
MAIN
SECTION
Q302
MUTE
DM_R
IC602
S-RAM
40 DM-R
SOURROUND-IN-L 3
SOURROUND-IN-R 7
SOURROUND-IN-L
SOURROUND-IN-R
VRSWIN
SW-IN 15
Q276,277
MUTE
CONTROL
A0 – A15
DATA
DVD MUTE
O
MAIN
SECTION
P
MAIN
SECTION
J302
SW
SW-OUT 22
SUB WOOFER OUT
Q301
MUTE
17 18
Q274,275
MUTE
CONTROL
6 CS
17 WE
IC352
A/D CONVERTER
ANALOG-IN-L
L
1 VINL DOUT 15
R-CH
HDOUT 82
HACN 82
GP3 120
41 FL-IN
Q303
MUTE
MAIN
SECTION
74
75
76
136
140
141
8
FL
DVD MUTE
ADC_DATA
F
VIDEO
SECTION
BCK
LRCK
XCK
BCK 14
5 VINR LRCK 13
SYSCLK 16
DOUT
ACK
ERROR
DIN
CLK
HCE
EXLOCK
PM
BST
XRST
DOUT
ACK
ERROR
DIN
CLK
HCE
EXLOCK
PM
BST
XRST
7-10, 13-16,
29-32, 35-38
43,44,51,32,31,22-20,
52,53,56,79,57,58,67,68
CS0 44
WE0 45
9
VOUT7 16
5-1, 44-42,
27-24, 21-18
A4,A12-A15,A10,A9,
A11,A8.A7,A5,A6,A0-A3
139 MCLK2
105,50,42,41,34,69,70,59,77,
78,95,86,122,114,113,106
144 MCLK1
D26-D24,D27-D31,
D23-D21,D16,D20-D17
VOUT6
X601
12.288MHz
IC301
SOUND PROCESSOR
CLK
VIDEO
SECTION
H
VIDEO
SECTION
5 7 22 26 27 23 21
6 24 25
33
50 49
48
38 35
DSP DIN
DSP CLK
DSP HCE
DSP EXLOCK
DSP PM
DSP BST
DSP XRST
DSP DOUT
DSP ACK
DSP ERROR
A-MUTE
VR-DATA
VR-CLK
SW MUTE
IF-DVD-RESET
MUTE REQ
SYS RESET
MUTE REQ
SYS RESET, MUTE REQ
• R-ch is omitted due
to same as L-ch.
• SIGNAL PATH
: AUDIO
IC401 (1/2)
SYSTEM CONTROL
VIDEO
SECTION
K
V-MUTE1, V-MUTE2
V-MUTE1
V-MUTE2
: TUNER
37 IF-VIDEO-MUTE1
36 IF-VIDEO-MUTE2
27
27
HCD-WZ8D
– Main Section –
IC101
SOUND PROCESSOR
J101(1/2)
MD(VIDEO)
IN
L
37 IND2
AUDIO
SECTION
R-CH
R
DOWNMIX-L
N
AUDIO
SECTION
EXCEPT AEP, UK, RU
OUT2 25
3
h
R
R-CH
J603
i
35 REC B2
MIC LEVEL
IC702(1/2)
MIC AMP
HEADPHONE AMP
IC103
3
1
40 INA2
R-CH
RV702
J701
R-CH
2 MIC
ANALOG-IN-L
L
MD(VIDEO)
OUT
Q270
MUTE
38 INC2
R-CH
J101(2/2)
L
REC A2 36
39 INB2
IC401(2/2)
SYSTEM CONTROL
IC702(2/2)
MIC AMP
1
6
+
Q101
DBFB
BB A2 27
AUDIO
SECTION
M
F-L
BB B2 26
41 SUR2
7
Q171
MUTE
R-CH
1
Q191
VACS
VACS IN 97
EXCEPT E2
19 SA OUT
VOL-DATA 52
RV701
21 DATA
VOL-CLK 51
ECHO LEVEL
SW OUT 24
TOUT 29
22 CLOCK
2
h
ECHO
AMP
P
AUDIO
SECTION
SOUROUND-IN-L
O
AUDIO
SECTION
R-CH
IC701
J702
VRSWIN
Q272,273
9
MUTE
CONT
HP/REC OUT MUTE 77
MUTE
2
HEADPHONE IN 63
EXCEPT E2
Q401
DXA-WZ8D(3/3)
1 MIC-CHECK
FRONT-L
R CH
FRONT-R
DBFB FB
IO EXP DATA OUT
IO-EXP DATA IN 59
IO EXP DATA IN
IO-EXP DATA OUT 58
TUNER UNIT
+9V
IO EXP CLK 61
IO EXP CLK
IO EXP LAT 60
IO EXP LAT
STK MUTE
STK MUTE 65
ST A+9V
L OUT
R-CH
R OUT
ST D OUT
45 ST-DOUT
ST DIN
46 ST-DIN
ST CLK
47 ST-CLK
A SHUT 89
A SHUT
B SHUT 90
B SHUT
A TRG 91
A TRG
B TRG 92
B TRG
CN CHECK
EVER +4V
CN CHECK 53
LCD-DATA 81
ST CE
44 ST-CE
TUNED
43 TUNED
LCD-CLK 82
42 STEREO
LCD-ENB 83
ST MUTE
41 ST-MUTE
LCD-RS 84
RDS DATA
40 RDS DATA
STEREO
Q907 - 910
LCD201
(FAN)
M +7V
LCD RESET 100
RDS INT
AEP,UK
AD KEY1 95
+1.8V
PUSH ENTER
Q521,523
PB-R
R-CH
MUTE
Q501
MUTE
CONT
IC501
REC-L
3
Q522,524
REC-R
R-CH
MUTE
Q502
55 TC LINE-MUTE
REC
AMP
AD KEY2 94
2
VOL B 68
Q520
56 ALC
PB SW
Q581,582
IC581
57 TC REC-MUTE
Q583-585
AMS
5
IC906
S611-623
D +5V
FUNCTION
KEY
V +5V
VOLUME
ENCODER
+5V
REG
3
D901
DVD AC
IC913
2
1
+5V
REG
1
5
IC904
VOLUME
POWER KEY 74
S603
I/
DISPLAY KEY 73
S602
DISPLAY
LED AROUND PLAY 71
66 TA MUTE
LED MD(VIDEO) 75
LED TAPE A/B 72
IC601
2
M +12V
+12V
REG
1
4
Q903,904
DVD PWR
CONTROL
LED TUNER/BAND 69
4
SIRCS
LED STANDBY 76
D+3.3V
I2CDATA
CN401
JIG
29 IIC CLK
BACK-LIGHT3 78
BACK-LIGHT2 79
• Signal Path
J
X401
32.768kHz
I2CDATA, I2CCLK
D602-606
LED
DRIVE
10 XC-IN
AMP +9V
Q601
: MD
AU+9V
(STANDBY)
D402
µCOM
D+3.3V
D608-613
(BACK LIGHT)
4
MOTOR
DRIVE
2
A+4.5V
RIPPLE
FILTER
HP AMP
RIPPLE
FILTER
D403
Q182
AC-CUT 20
15 X-IN
RESET 12
RESET
SWITCH
IC251
3
RESET
D294
IC905
1
AUDIO_5V
D295
13 X-OUT
LOADING
M
MOTOR
3
+5 V
REG
IC902
1
3
+9 V
REG
1
IC392
7
85 LOAD-OUT
9
86 LOAD-IN
AUDIO_D3.3V
EXCEPT AEP,UK,RU,E2,MX
3
+3.3 V
1
REG
IC393
OPEN
AUDIO_D2.5V
(DSP)
IF-DVD-POWER 30
39
88 CLOSE-SW
28
3
+2.5 V
1
REG
Q902
87 OPEN-SW
CLOSE
+9V
REG
Q161
µCOM
+VCC
IC202
: PB (TAPE)
3
ST A+9V
LED
DRIVE
Q293
X402
16MHz
D+4V
BACK-LIGHT1 80
11 XC-OUT
: TUNER
IC901
D601
LED
DRIVE
Q608,609,611
30 IIC DATA
I2CCLK
• R-CH is omitted due to same as L-CH
VIDEO
SECTION
Q602-606
LED CD(DVD) 70
REMOTE
CONTROL
RECEIVER
g
: REC (TAPE)
1
+3.3V
1
REG
54 AMS-IN
TA MUTE
: AUDIO
+3.3V
REG
S601
VOL A 67
5
MUTE
CONT
DVD +3.3V
IC907
3
A3V-2
(ZIVA)
DVD AC
IC903
2
D +3.3V
4 DIRECTION
SWITCH
PB-L
+1.8V
3
1
REG
FUNCTION
KEY
S637
DXA-WZ8D(2/3)
D911-D913
IC211
S631-636
S638-640
18 RDS INT
M +9V
LED +9V
FAN
CONTROL
28
DVD PWR
CONTROL
Q901
B+
SWITCH
1
UNREG
HCD-WZ8D
4–3. Schematic Diagram – RF Board – • See page 24 for Waveforms. • See page 55 for IC Block Diagrams.
C028
0.1
C025
0.1
R023
820
C031
1000p
C006
22
10V
R026
12k
C013
0.1
C026
0.1
C029
0.01
C035
0.1
R024
0
C023 22p
C018 5600p
C020 22p
C022 22p
JL004
C021 22p
CN001
24P
CN002
29P
C030 0.01
C024
0.01
JL005
JL007
C027
0.1
R025
100
C009
0.1
C019
5600p
R022
220
R027 0
R028 0
C017
2200p
R029 0
A
C016 2200p
C015 2200p
C032
0.047
JL006
C014 2200p
C042
180p
R001 100
JL003
R014 0
R013 0
C033
0.1
C005
22
10V
C012
0.1
R032
100
IC001
CXD1881AR
R012 0
R011 0
R018 0
R017 0
C049
0.1
R016 0
JL002
R015 0
JL001
R041
1k
R020
0
C008
0.1
C041
0.1
R021
0
C040
0.1
R003
33
R004
33
R005
47k
C001
100
6.3V
R006
470
R007
33
IOP2
IOP1
Q001
2SB1132-T100-QR
Q002
2SB1132-T100-QR
CN003
9P
D001
1SS355TE
-17
L001
47uH
C002
10
16V
D002
1SS355TE
-17
C010
1000p
30
R008
33
R009
47k
C003
100
6.3V
R010
470
C011
1000p
L002
47uH
C004
10
16V
30
C037 330p
C039 0.033
R019
0
C038 0.033
R035
0
R033
0
C036
0.47
R034
10M
C034
0.1
(2/9)
CN501
34
HCD-WZ8D
4–6. Schematic Diagram – DMB03 Board (1/9) – • See page 56 for IC Block Diagrams.
(1/9)
(6/9,9/9)
(Page 38,41)
(4 /9)
36
* CN107
25P(AEP,UK,RU,AUS)
@AUDIO_DGND
@AUDIO_D3.3V
CL309
C309
100p
C308
100p
R311 100
3.2
R312
100
D392
1SS355TE-17
CL311
36, 39
C392
22
16V
(4 /9)
+2.5V REG
C393
0.01
C394 JW392
0
220
4V
IC393
BA25BC0FP-E2
3.3
36
R392
10
D393
1SS355TE-17
D1801
1SS355TE-17
D1802
1SS355TE-17
(4/9,6/9,7/9)
36, 38, 39
R1801
0.1
C396
0.1
R314
22
C397
220
4V
C325
100
4V
CL313
C324
0.01
5
C306
0.01
C323
0.1
1.6
1.6
2.5
C395
0.1
FL302
0uH
5
2.7
1.6
CL315
2.5
C326
0.01
CL316
5
C322
0.1
IC302
PCM1609KPTR
2.5
2.5
2.5
2.5
R1301
0.1
D1304
1SS355TE-17
F
CL317
D1303
1SS355TE-17
CL320
C1302 R1302
0
0.1
CL321
52
CL322
CL323
2.5
2.5
2.5
2.5
R305
220
36
CL324
C305
0.01
R304
220
C304
0.01
R303
220
C303
0.01
C302
0.01
R1304
0.1
R302
220
FL303
0uH
R327 0
38
R335 0
R328 0
(6 /9)
R329 0
FL352
0UH
1.5
R362
10k
C363
0.1
C364
100 6.3V
C367
470p
C355
100
6.3V
C368
470p
R353
1K
C357
1
50V
C352 100 6.3V
C366
100
6.3V
33
C365
0.1
IC352 PCM1800E/2 K
33
R352
1K
C356
1
50V
4CH-VOL
CN303
CL318
CL319
C321 R307
100 220
6.3V
R1303
0.1
C1304
0
CL314
C307
0.01
R306
220
R1803
0.1
(4 /9)
D394
1SS355TE-17
SL392
SL302
DAC_RST
IC392
uPC2933T-E2
(4/9, 7/9)
CL312
R313
10k
IC393
D1301
1SS355TE-17
39
21P(EXCEPT AEP,UK,RU,AUS)
*
CL310
R308 220
AEP,UK,RU,E2
D1302
1SS355TE-17
(7 /9)
CN107
R310 100
5
(Page 41)
@AUDIO_D2.5V
5
37
(9 /9)
R309
220
CL325
DOUT
38
(7/9)
39
HCD-WZ8D
4–7. Schematic Diagram – DMB03 Board (2/9) – • See page 57 for IC Block Diagrams.
(2/9)
R587
0
CL505
CL504
CL503
R502 0
R538 0
R539 0
R508 0
R544 0
CL501
R540 0
FL502
0UH
R541 0
R585 0
R583 0
CL502
C567
0.1
C568
10
C522
0.1
6.3V
B
CL544
C590
0.0022
C502
0.01
3.3
R578 0
(3 /9)
3.3
R506 47k
R560
1k
C570
10
3.3
C531
0.047
C544
0.1
3.3
CL517
CL518
SL502
R572
470k
R562
1k
CL520
R561
1k
C553
0.0033
C534
0.022
C535
0.0022
C548 0.01
C547
0.1
R566
10k
R565
1k
(4 /9)
36
34
34
R571
1M
C565
0.1
C552
0
C559
0.1
R567
3.3k
C560
0.0015
R601
0
R568
1M
FL501
0UH
R615
0
C558
100
4V
C563
100p
C556
10
R507
0
R573
10k
C569
0.1
C533
0.0022
C561
0.1
R558
47k
3.3
SL501
35
R629 0
R577 0
R505 47k
CL516
CL521
3.3
3.3
R576 0
R575 0
R504
47k
CL515
CL519
3.3
R501 0
R564 1k
CL528
CL514
R699 0
R563 1k
C573 100p
CL513
IC509
CXD3068Q
R593 100k
CL512
R552 1k
R559 1k
C501
0.01
CL511
30
R698
0
R551 1k
C589
0.0022
R599
1k
R503
47k
CL506
0.7
R550 1k
C588 0.0022
CL509
CL510
3.3
C543
0.1
0.9
0.9
CL525
CL522
C545
10
IC503
NJM3404AV(
TE2)
R588 10k
CL526
CL508
CL507
C551 0.47
C517 10 10V F
CL527
CL523
R695 0
R696 0
CL529
CL524
R694 10k
3.2
CL530
A
1.9
R555
0
0.9
3.3
C516
0.0022
50V
B
R592
0
R584 33k
CL531
R9988
0
R536
10k
C592
10
16V
C518 0.01 50V F
CL535
3.3
R548 10k
R537
68k
CL537
CL536
3.3
R545 10k
CN501
29P
3.3
3.3
R569
0
HCD-WZ8D
4–8. Schematic Diagram – DMB03 Board (3/9) – • See page 58 for IC Block Diagrams.
FL702
C780
10
C777
0.1
C716
0.47
R748 33k
0.1
0.2
3.3
0.5
C723 0.1
0.5
0.5
0.5
3.3
0.5
0.5
0.5
0.5
C722 0.1
C718 0.1
1.6
R717 100k
R780 0
3.3
R716 100
R781 0
R719
1k
R747 33k
TP701
1.7
C714 0.1
2.4
2.4
3.3
1.5
3.3
1.6
2.1
C752
0.1
R751
0
FL703
0UH
R718
10k
1.7
1.7
C713 0.1
R712
10k
CL703
R713 10k
R711
2.2k
3.3
C711
0.047
R709
150k
C715
0.0015
C712
100p
R714 10k
C706
0.1
R710 10k
C702
10
R708 470k
C709
0.1
3.3
R789
100k
C708 0.01
C783
C729
0.0015
10
50V
10V
B
F
TP703
C703
0.1
0UH
R707 100
FL706
R700
8.2k
R715 10k
FL701
0UH
R788
100k
1.7
C701
100
4V
1.7
R784
0
1.5
R786
100k
R787 100k
C705
0.01 16V B
IC703(2/2)
NJM3404AV(
TE2)
C782
0.0015 50V B
R785 10k
(3/9)
0UH
C779
10
C778
0.1
3.3
R725
1.8k
C730
0.1
0.1
FL704
0UH
C776
0.1
R765 22k
C781
150
4V
R767
47k
C774
0.0047
C775
0.1
0.1
3
C772
0.1
R764
1M
R763
8.2k
C773
0.47
C771
0.047
R762 22k
3.3
R730 22
3.3
C740 0.1
0.6
0.6
0.5
R731 22
0.6
0.6
0.5
C724
0.1
0.6
0.6
R758 0
1.8
R757 0
5
C741 0.1
R766 0
R755
0
CL791
0.6
0.6
0.6
C769
0.1
R778
100k
C768
0.1
IC701
CXD-1882R
3.3
3.3
C767
0.1
R754
0
CL787
R753
0
CL786
3.3
0.5
0.5
3.3
3.3
3
R735 10k
R736 10k
C766
100p
R776
0
3.3
3.3
0
0.2
0.1
C743 0.1
1
0.5
IC706
MSM51V1816
5F-60TSKR1
R734 10k
R799
0
0.5
R732 10k
C742
0.1
CL785
0.5
0.6
0.6
R733 10k
R752
0
0.5
0.6
0.6
0.6
5
3.3
R728
10k
3.3
C725
0.1
0.6
R756 0
IC703(1/2)
NJM3404AV(
TE2)
FL705
0UH
C727
10
3.3
R759 0
34
CL701
3
3
3
0.6
R727
3.3k
C728
0.1
C721
0.1
C720
0.1
3
R770 0
(2 /9)
R721
33k
3.3
R769
2.2k
C770
0.1
2.6
R720
1k
0.1
3
SL703
R726
100k
R724
1k
3
0.1
3
3
0.1
3
3.3
R737 10k
R738 10k
3
0.1
C726
0.1
C765
0.1
R750
10k
0
3.3
3.3
C744 0.1
2.7
2.7
2.3
R741 22
2.7
R742 22
2.7
C745 0.1
R743
22
(6 /9)
38
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
R777
0
C762
0.1
R746
47k
CL776
CL777
R745
47k
CL778
C763
0.1
C764
0.1
R744
22
(5 /9)
37
35
35
CL775
CL774
R9987
0
C760
0.1
CL773
C761
0.1
R9986
0
CL772
CL771
CL770
HCD-WZ8D
4–9. Schematic Diagram – DMB03 Board (4/9) –
(2 /9)
34
(4/9)
JL521
C527
0.01
50V
F
C526
22
16V
R543
0
R547
0
(5 /9)
R581
12k
37
R589
10k
R580
33k
(6 /9)
38
0.1
C519
0.01
(1 /9,7/9)
33, 39
R579
8.2k
C514
0.01
IC501
FAN8035L
R534
56k
R535
0
R532
0
R530
56k
R531
0
(1 /9,6/9,7/9)
33, 38, 39
R533
33k
R529
33k
R528 0
D901 1SS355TE-17
C512
0.01
(7/9)
39
C926
220
4V
3.3
C927
0.01
50V
F
R525
10k
C510
0.001
C509
330p
R527
2.2k
R524
10k
R521
100k
R522
4.7k
R523 10k
V+5V
C925
22 16V
35
(6/9)
(Page 38)
IC907
uPC2933T-E2
R586 200k
R513
56k
C504
33000p
3.3
C529
0.01
(1/9)
R519
100k
R512
56k
C503
33000p
33
R520
10k
R516
4.7k
C506
330p
R517
2.2k
(1/9)
33
C508
0.001
CL931
CL932
CL933
C528
22
16V
R553 0
R597
0
R554 0
CL935
C101
220
4V
C525
0.01
C151
100
6.3V
CL937
C
CL939
CL940
CL941
R510
150k
CL942
CL943
D1101 1SS355TE-17
R511
150k
R1101 0.1
D1102 1SS355TE-17
36
36
CN102
13P
(1/9)
33
REGULATOR BOARD
CN506
50
HCD-WZ8D
4–10. Schematic Diagram – DMB03 Board (5/9) – • See page 24 for Waveforms. • See page 58 for IC Block Diagrams.
(3 /9)
35
CD_DOUT
CD_DOUT
(5/9)
39
(7 /9)
39
(6 /9)
R911 10k
R907 22
R906 22
R905 22
3.3
Q901
DTC114TE-TL
3.3
3.3
C906 0.01
3.3
3.3
3.3
IC902
TC7S32FUTE85L
IC904
TC7W74FKTE85L
3.3
3.3
3.3
3.3
C918 0.01
IC903
BR24C16F-E2
3.3
3.3
R901
22
C901
100
4V
R978 10k
C902
0.01
R902 22
FL901 0UH
36
3.3
3.3
(4 /9)
R912 10k
38
R913
10k
R918
22
3.3
C907
0.01
50V
F
R974 0
3.3
R949 0
3.3
R948 0
R947 0
FL908 0UH
C904
0.01
C903
100
4V
C909
100p
CL905
JL967
3.3
JL965
IC901
CXP973064-228R
R988 0
R932
22
1.1
R995 0
2.7
2.7
2.7
CL934
R996 0
3.3
0.1
0.1
0.1
C915 6p
0.5
JL957
C914 X902
9p
27MHz
R998 0
R927
1M
C913 33000p
JL956
L901
47uH
R920
100
3.3
FL903
0UH
C917
0.01
C916
100
4V
R990 0
CN101
7P
3.3
CL906
Q903
2SK1828TE85L
CL907
3.3
CL908
R922 22
R984
10k
CL959
CL955
CL950
36
(6 /9)
38
0.4
0.4
0.5
3.3
2.1
3.3
3.3
R926 100
R928 100
R929 100
R930 100
C905 0.01
R971 0
R940 100
C910 0.01
R910 0
R973 0
R943
100
R921 100
R970
0
R923
220
R925
100
R904
10k
54
55
X901
20MHz
37
37
CL951
CL952
CL953
R935
4.7k
C924
0.01
R976 0
7
R908 10k
R975 10k
R942 100
VIDEO MUTE
43
3.3
CL910
6
CN901
7P
CL954
R964
10k
CL909
VIDEO SW
R933
22
FB902
0UH
1.2
R997 0
3.3
(1 /2)
CN101
CL904
0.4
R994 0
0.1
B
FB903
0UH
C908 100p
R917 1k
1.4
2.7
Q904
2SK1828TE85L
CL913
IC906
SM8707GV-G
-E2
R931
22
R916 1k
JL966
JL911
R962
10k
3.3
R915 100
3.3
R919 0
JL910
R992 0
CL922
R958
22
3.3
3.2
3.3
R991 0
HCD-WZ8D
4–11. Schematic Diagram – DMB03 Board (6/9) –
(6/9)
CN202
4P
(3/9)
(Page 35)
(7/9)
(Page 39)
(5/9)
(Page 37)
CN105
17P
1
2
3
4
VIDEO SW
VMUTE
5
PCM
6
7
IC255
TC7S00FU
(TE85R)
(1/9,9/9)
(Page 33, 41)
E
8
9
10
VIDEO BOARD
CN801
(Page 54)
11
C283
0.01
12
13
14
15
VGND
16
17
I/P SW
WIDE
V5V
R223
0
R9998 0
(1/9,4/9,7/9)
(Page 33, 36, 39)
R217
0
IC256
SN74LV573A
PWR
CL210
CL209
CL208
R224
0
CL207
CL204
R9999 0
CL206
R9994 0
R218
0
(4/9)
(Page 36)
C284 0.01 50V F
R270 0
V+5V
R278
75
R279
75
R280
75
R281
75
R282
75
C412
0
C413
0
C414
0
C415
0
C416
0
L402
0
L403
0
L405
0
L406
0
IC258
SN74LV573A
PWR
IC259
SN74LV573A
PWR
R9980 0
2.3
54
R198
4.7K
55
36
(4/9)
(Page 36)
(5/9)
(Page 37)
R9981 0
R291 0
R292 0 0.5
0.5
R9982 0
0.5
R9983 0
R9993
0
R222
0
R295 0
1.5
R219
0
D1202
1SS355TE-17
L412
0
L413
0
L414
0
L415
0
D1201
1SS355TE-17
L416
0
R1201
0
C287 0.01 50V F
(7/9)
(Page 39)
52
R293 0
R294 0
R9985
0
ADC_DATA
R1202
0.1
R221 0
R296
0
C286 0.01 50V F
D1203
1SS355TE-17
D1204
1SS355TE-17
R220
0
R9984 0
R197 4.7K
L404
0
(7/9)
(Page 39)
38
38
53
(1/9)
(Page 33)
35
HCD-WZ8D
4–12. Schematic Diagram – DMB03 Board (7/9) – • See page 24 for Waveforms.
(6/9)
53
52
38
(5/9)
(7/9)
37
39
R263
75
R268
0
R269 0
CD_DOUT
R265
75
R264
75
R266
75
R267
75
R574
330
R239
100
IC252
R225 0
R228 0
ST
Y
SL
IC252
TC7WH157FK(TE85R)
C238
0.01
C234
0.01
3.3 SWITCHING
0
0
*
R1001
0
C289
0.01
(1/9)
33
JL203
R284
180
R288
0
AEP,UK,RU,AUS
JL204
C233
0.01
R277 0
R276 0
R275 0
C232
0.01
C231
0.01
R274 0
R273 0
C230
0.01
R207 0
Y
GND
38
DOUT
0
0
0
0
3.3
0.6
3.2
0.7
3.2
3.2
3.2
3.2
3.3
R283
1k
3.2
JL207
1.2
3.3
3.3
3.3
JL208
JL211
JL209
JL210
JL212
3.3
JL214
JL213
R260
4.7k
R1000
4.7k
C229
0.01
C237
0.01
R261
4.7k
C236
0.01
R233
0
1.6
B
*
C226 0.1
R259
4.7k
VCC
*
R226 0
R251
0
A
(1/9)
33
R253
4.7k
R254
4.7K
R285
0
ADC_DATA
1.5
3.3
C241
0.01
0.6
R240
47k
3.3
3.3
0.4
0.8
3.3
R234
10k
Q202
DTC114TE-TL
C242 0.01
R15 22
C244 0.01
R243
0
3.3
0.5
0.5
0.7
0.3
IC204
BR9040F-D-WE2
0.8
(6/9)
C247 0.01
38
0.8
3.3
C248
0.01
0.4
R14 22
1.3
0.6
1.1
0.7
C204
0.01
50V
F
3.3
C251 0.01
C252
0.01
IC207
ZIVA5X-C1F
R227
4.7k
0.8
0.8
0.9
0.8
3.3
0.4
3.3
R248 4.7k
C253 0.01
R13 22
C256
0.01
0.7
0.7
1.5
0.6
0.6
0.6
1
0.5
3.3
0.4
JL216
R241 JL217
0
C260
0.01
3.3
R244 1k
2.7
R805 0
R246 10k
0.7
0.7
R247 1k
3.3
CL256
CL254
CL255
CL251
CL252
CL253
40
R12 22
C257
0.01
R255
0
(8/9)
C261 0.01
C216
0.01
JL218
1
1.7
3.3
CL257
C262
0.01
R213 68
C263 0.01
D202
1SS355TE-17
R232
33
C215
0.01
RB18
33
RB20
33
R11 22
2.9
2.5
2
0.2
2
1.9
R10 22
3.3
2.9
RB21
33
RB19
33
33, 36, 38
C214
0.01
JL202
C270
0.01
C272
0.01
FL206
0UH
(1/9,4/9,6/9)
R245 4.7k
C267
0.01
R257 4.7k
36
IC211
C266
0.01
C265
10
C269 0.01
FL205
0UH
(4/9)
C268 0.01
C271 0.01
0.5
0.4
0.6
0.4
0.5
1.2
0.5
1.2
3.3
3.3
R231
33
3.3
R230
33
3.3
(6/9)
C213
100
4V
(1/9,4/9)
33, 36
*: impossible to measure
(8/9)
40
39
39
HCD-WZ8D
4–13. Schematic Diagram – DMB03 Board (8/9) – • See page 57 for IC Block Diagrams.
(8/9)
IC203
HY57V283220T-6
C218
0.01
3.3
1
C255
10 10V F
C220
0.01
0.8
0.7
FL203
0UH
FL204
0UH
C258
10
C259
0.01
0.9
3.3
0.7
RB10 68
0.5
C205
0.01
C235
0.01
C227
0.01
0.8
0.7
RB12 68
3.3
1
0.7
0.6
1.5
3.3
0.6
0.6
IC206
MBM29DL324BE-90PFTN-SB3V107
C275
0.01
0.8
3.3
C239
0.01
RB13 68
RB11 68
C240
0.01
3.3
3.3
0.4
3
2.9
2.9
IC216
SN74ALVCH1
6841DGGR
2.5
CL350
(7/9)
CL351
CL389
CL352
CL388
CL353
CL387
CL354
R262
0
CL355
R250 0
39
3.3
R214 0
CL385
CL356
CL384
CL357
2
0.5
2
1.2
0.4
0.4
0.5
0.5
3.3
0.6
1.2
3.3
0.4
C315
0.01
3.3
CL386
R215
0
3.3
3.3
C264
0.01
C243
0.01
3.3
0.7
CL383
CL358
CL382
CL359
CL381
CL360
CL380
CL361
CL379
CL362
CL378
CL363
CL377
CL364
CL376
CL365
CL375
C281
0.01
3.3
0.6
C246
0.01
RB14 68
CL367
CL368
CL372
CL369
0.4
3.3
1.3
0.8
3.3
HA1
0.8
0.3
C254
0.01
C250
0.01
CL373
C245
0.01
RB16 68
0.8
3.3
CL374
0.6
1.1
CL366
3.3
R301
1k
3.3
0.2
1.9
CL390
C282
0.01
0.4
RB15 68
CL371
CL370
SYS_RST
(7/9)
39
40
40
0.5
3.3
0.7
3.3
C316
0.01
C249
0.01
0.5
RB17 68
HCD-WZ8D
4–14. Schematic Diagram – DMB03 Board (9/9) – • See page 24 for Waveforms.
C616
0.1
R610
100
R612
100
R611
100
R614
100
C611
0.1
R613
100
C617
0.1
C610
0.1
C612
0.1
R633
0
C609
0.1
IC602
IS61LV6416-
10TT(ISSI)
C613
0.1
R624
0
R623
0
R622
0
R621
0
R620
0
R630
0
C614
0.1
IC601
CXD9782R(E3)
C608
0.1
FL601
0UH
C601
0.1
C603
10
JL615
XX
C607
0.1
FL602
0UH
C650
0.1
C651
10
X601
12.288MHz
R616
100
R617
100
C626
56p
C627
22p
R619
0
R626
0
R609
0
R625
0
C615
0.1
C606
0.1
0
0
0
R604
R605
R606
R608
0
0
C619
0.1
0
R603
0
R628
C618
0.1
C605
0.1
R627
41
41
JW607
JW604
JW605
JW606
JW601
R607
100
JW602
R602
1k
JW603
CN103
11P
R618
1M
HCD-WZ8D
4–16. Schematic Diagram – Main Section (1/2) – • See page 59 for IC Block Diagrams.
CN104
100k
R292
JW7
JW6
D252
1SS355
100k
R242
R241
R291
CN105
R277
220
Q275
DTC114EKA
C272
100 10V
C271
100 10V
0
R280
Q274
DTA114EKA
JW9
Q272
DTA114EKA
J101
C174
10 50V
100k
1k
R105
100k
1k
R103
10k
680
R140
1M
C109
0.068
C140
1 50V
R104
C111
10
50V
0.18
C108
10
50V
0.33
R115
10 50V
10 50V
1k
Q271
2SC3624A
C102
R271
C175
0.1
R114
0
C104
Q270
2SC3624A
C112
R270
C113
C182
10 50V
0.0047
R182
100k
1k
R275
C110
1k C181
220p
R274
R273
220
Q273
DTC114EKA
100k
0
R181
10 50V
10 50V
C184
C172
R172
10k
220p
220p
0.022
R183 4.7k C183
R171 1k C171
R102
0
C270
100
10V
Q101
2SC1623
0
C107
C180
JR1
R101
2.2k
R184
0.022
R174
100k
C106
C173
R173 4.7k 220p
R112
10k
0.1
JW4
JW5
C126
IC101
M61529FP-D60G
C220
100 10V
100 10V
C125
JW3
L220
JW2
IC201
TOTX141
CN102
11P
680
R194
68k
R168
Q151
2SC1623
C166
100
10V
C134
47
50V
R195
100
C165
10
50V
R167
4.3k
Q161
2SC3624A
R166
3.3k
JW1
100
C221
R193
22k
R155
100k
10V
0.1
C222
0.01
1k
C225
R221
R196
330
C129
10 50V
R153
10k
C161
10
50V
R222
680
Q191
2SC1623
R154
C163
C162
0.33
0.18
0.068
0.0047
C159
C158
10
50V
C133
10
50V
R197
1k
10k
330
R151
2.2k
R152
10k
R113
C160
0.022
C156
0.022
10 50V
C152
C157
10 50V
10 50V
C124
C154
C123
100
10V
IC202
BA6956AN
CN101
7P
B
1SS355
B
D201
D202
1SS355
C227
0.01
S001
0.1
C242
CN110
16P
CN111
15P
CN103
5P
43
0.1
C226
0.01
CN001
5P
M001
C244
C402
0.1
43
NO807
4P
HCD-WZ8D
4–17. Schematic Diagram – Main Section (2/2) – • See page 24 for Waveforms. • See page 59 for IC Block Diagrams.
Q276
DTA114EKA
CN107
15P
R279
220
Q277
DTC114EKA
C114
10 50V
C403
0.1
R106
R156
0
0
C164
C193
1000
10V
R198
1k
10 50V
C194
100
10V
R451
1M
100
10k
R463
R497
JW100
R179
R160
R481
100
R482
100
R449
100
R483
100
R448
100
R484
100
R447
100
R450
100
C189
10 50V
R486
10k
R446
100
R487
100
R444
100
R488
100
R443
100
R462
10k
R489
1k
R442
100
R464
10k
R490
1k
R491
1k
R440
100
R492
1k
R439
100
R438
100
R493
D191
RB501V
R498
470
R499
R441
15k
15k
R495
470
C497
0.1
C498
10 50V
R437
100
R436
100
R435
R186
C190
22p
47k
R180
10k
NO808
3P
JW8
R175
10k
C170
22p
C187
1000 10V
100
R177
100k
C177
1000
10V
R189
22
R187
100k
Q181
2SC3624A
R190
10k
R159
22
CN109
23P
IC401
R496
R494
C179
10
50V
47k
R185
10k
Q171
2SC3624A
R149
22
IC103
R176
47k
R445
10k
22
R150
47k
R188
1k
R485
EP101
MT
1k
FB462
0
R178
R434
10k 10k
100
100
R453
R455
R454
1k
100
100
R458
R457
1k
R459
R456
1k
100
R461
R460
100
C462
10V
0.01
C463
100
R465
C475
0.01
100
R466
R412
10k
100
100
R468
R467
C476
0.01
10k
R408
R414
10k
100
100
R470
R469
100
10k
R410
100
R471
R472
100
100
R474
R473
100
100
100
R476
R478
R475
100
100
R480
R479
Q182
2SD2525
100
D284
1SS355
100
100
0.1
JW440
R431
C499
D193
0
10k
R416
10k
100
100
R430
1SS355
10k
Q293
D293
2SC1623
1SS355
R296
22k
R294
10k
D292
1SS355
D403
R402
R295
22k
C292
0.1
C293
0.1
4.7k
D294
1SS355
1SS355
R298
220
IC251
M62703SL
D295
1SS355
R299
10k
R297
D402
C294
10 50V
100
100
CN401
4P
10k
R426
R427
R415
100
100
100
R423
R424
R425
100
100
R421
R429
JR418
R417
FB416
4.7k
R420
R422
X402
16MHz
R418
100
C417
2200 6.3V
0
R413
0.1
C412
C416
330k
32.768KHz
R411
X401
CH
15p
100
R407
C411
100
R406
CH
100
100
R405
R452
100
R404
Q401
DTC114EKA
C400
0.1
18p
10k
C452
R400
EP102
C410
10k
0
0.1
R401
0.1
FB499
0
C401
0.1
R409
1SS355
1 50V
100k
R199
D192
C198
RB501V
R433
100
JR21
C255
0
C254
10
50V
0.1
C253
1 50V
CN108
9P
44
44
HCD-WZ8D
4–19. Schematic Diagram – PANEL Board –
D606
SEL5E23C
D605
SEL5E23C
D604
SEL5E23C
D602
SEL5423E
D603
SEL5E23C
DVD
D601
SEL5223S
C606
0.001
C605
0.001
C604
0.001
C603
0.001
Q608,609,611
NO805
4P
WIRE
Q
Q608
2SC1623
5.6
R601
1k
Q611
2SC1623
Q609
2SC1623
R676
1k
R606
1.5k
3.2
2.4
0.8
0.2
Q606
DTC114EKA
Q601
DTC114EKA
0.8
R655
1k
R654
1k
R637
1.5k
R657
100
R662
100
R671
1.5k
R605
1.5k
0.1
<6.7>
[6.1]
0.1
0.1
R656
1k
R665
1k
R638
1.5k
R672
1.5k
R604
1.5k
R673
1.5k
R603
1.5k
6.8
<0.1>
6.7
<0.1>
<3.2>
R639
1.5k
<3.2>
Q605
DTC114EKA
R658
100
R640
1.5k
R602
1k
R674
1.5k
6.7
R659
100
R675
1k
7.3
Q603
DTC114EKA
Q604
DTC114EKA
R664
1k
Q602
DTC114EKA
R660
100
R661
100
CN605
23P
1.25FFC
O
S611
S612
S613
S614
S615
S616
S617
S618
S619
DVD
S602
J
R683
2.2k
S603
R621
680
S621
S620
S622
R623
1.5k
R624
1.5k
R625
2.2k
R626
3.3k
R627
4.7k
R629
10k
R628
6.8k
CN603
3P
AMP-L
48
R632
33k
SOUND FIELD
R622
1k
S623
R630
15k
R631
22k
R682
2.2k
S634
AEP,UK,RU
S635
MPX
44
S631
S633
S632
COLOR SELECT
EXCEPT AEP,UK,RU DVD TOP MENU,
EFFECT KARAOKE/MPX
R641
680
R642
1k
R643
1.5k
ALBUMR644
1.5k
S636
DVD MENU,
ALBUM+
R645
2.2k
P
R679
0
C601
47 16V
IC601
RPM7240-H8
CN604
2P
AMP-L
R681
2.2k
S601
R614
0
R678
0
R680
2.2k
DVD STOP
46
46
48
HCD-WZ8D
4–21. Schematic Diagram – LCD/Switch Section –
LCD201
D608-613
R652
33k
R257 100
R258 100
C265 100p
C264 100p
R256 100
R255 100
C262 100p
C267
0.1
D262
1SS355TE-17
R651
22k
R254 100
C250
1 50V
C263 100p
D261
1SS355TE-17
C252 0.1
C249 0.1
R252
10k
46
C261 100p
CN602
4P
AMP-L
C248 0.1
Q
C247 0.1
C246 0.1
R253
10k
C266 0.1
C251 1 50V
R636 1k
R670 1k
R696 820
R694 820
R693 1k
R691 1k
D610
SELU6614C
D613
SELS6E14C
R695 820
C622
D612
0.001
SELS6D14C
R692 1k
C611
D611
0.001
SELS6D14C
R669 1k
R634 820
R668 820
R608 820
R633 1k
R667 1k
R609 1k
EP601
MT
44
D608
0.001
SELS6E14C
R611 1k
C608
D609
SELU6614C
R635 1k
J603
7P
N
C623
0.001
R610 1k
CN601
3P
AMP-L
NO806
9P
WIRE
R653
68k
I
P
NO804
2P
WIRE
S638
S639
44
S640
46
R650
15k
R649
10k
S637
O
R648
6.8k
NO803
3P
WIRE
46
48
48
R646
3.3k
R647
4.7k
HCD-WZ8D
4–23. Schematic Diagram – REGULATOR Board – • See page 59 for IC Block Diagrams.
IC501
BA3308
R522
2.2M
C522
0.1
Q552
2SC3624A
R562
100k
R554
100k
R512
100k
R504
100k
C559
10 50V 5L
R563
1k
R556
10k
R510
390
C506
22 50V
C523
22 50V
R500
220
C509
10 50V 5L
R513
1k
Q522
DTC114EKA
R506
10k
R525
100
CN504
12P
R559
18k
C556
22 50V
CN503
8P
C521
100 10V
R560
390
R509
18k
R507
3.9k
R508
1k
C503
10
50V
Q520
DTC114EKA
R558
1k
R521
100
R557
3.9k
R561
33k
C553
10 50V 5L
Q502
2SC3624A
R511
33k
Q524
DTA114EKA
Q551
2SC3624A
R564
3.3k
R552
100
R551
100k
C551
0.0015
R553
10k
Q521
DTC114EKA
JW921
R523
100
C501
0.0015
R503
R514
3.3k
Q909
DTC114EKA
R502
100
IC903
SI-8033JF
Q523
DTA114EKA
CN506
13P
R583
8.2k
C929
0.1
2.2M
C586
22p
IC581(1/2)
NJM4558M
R592
4.7k
R591
10k
10k
1k
R586
C585
100
10V
R598
100
IC913
SI-8050JF
R588
R594
10k
Q583
2SC1623
R595
10k
CN501
15P
B-TO-B
1SS355
D902
RK36LF-B3
C588
0.01
R590
15k
R596
22k
D581
Q581
DTC114EKA
JW915
C924
1000
6.3V
C583
1 50V 5L
C589
10
50V
R589
15k
Q585
DTC114EKA
C906
0.01
C907
6800
35V
C587
0.01
Q584
DTC114EKA
C909
1000
35V
C910
3300
6.3V
C911
1000
10V
R585
R584
2.2k
0
0
10k
Q910
DTC114EKA
Q908
2SC1623
R905
100k
JW922
R582
C926
47
16V
R597
IC581(2/2)
NJM4558M
R587
C927
0.01
C905
0.01
1k
L901
100k
R916
220k
R581
D901
D3SBA20
22 50V
R919
10k
R593
R917
22k
R918
22k
CN507
2P
D905
UDZSTE-1782B
R501
Q501
100k 2SC3624A
C590
Q907
2SD2525
C928
0.01
10k
JW903
FB912
Q582
DTC114EKA
C584
470 10V
JW906
IC906
BA05T
JW926
L913
L911
L912
R915
120
EP901
C921
1000
10V
JW911
JW914
C920
3300
10V
R914
C923
1000
6.3V
330
JW928
JW907
C919
1000
35V
CN502
16P
B-TO-B
D903
RK36LF-B3
IC904
PQ12RF21
JW920
C915
0.1
50V
C914
2200
10V
IC901
TA7809S
Q903
DTC114EKA
16V
1000
Q904
DTC114EKA
IC902
TA7809S
Q901
2SB734
C912
10 50V
R901
2.2k
R908
100
R900
10k
C913
R907
100
R906
10k
R902
JW925
R903
JW919
2.2k
2.2k
Q902
DTC114EKA
C903
0.1
50V
C904
1000
10V
JW923
EP502
IC905
TA7805S
JW916
D913
10EDB40-TB3
C902
1000
6.3V
C901
10
50V
JW924
D912
10EDB40-TB3
D911
10EDB40-TB3
50
50
HCD-WZ8D
4–25. Schematic Diagram – 4CH-VOL Board –
CN301
*
C310
10 50V
CN303
*
JW305
47k
C362
10 50V
C333
0.1 MF
C332
0.22 MF
R331
1k
R332
2.2k
1M
R330
1M
C334
10
50V
C331
10
50V
C365
10
50V
C330
16V B
0.047
R363 10k
C315
10
50V
R362
C345
470 16V
C312
10 50V
1M
R313
10k
R312
C308
C311
B 10 50V
0.001
C344
100 16V
R310
2.2k
B
0.0022
B
R359
2.2k
C309
C302
220p
B
C303 220p
R360 2.2k
R303
10k
C359
0.0022
R302
470
47k
R361
C361
10 50V
R311
R309
2.2k
R301
47k
C348
0.1
F
B
C347
0.1
C358
B
0.001
C360
10 50V
0.1
C301
10 50V
C346
IC301
M61530FP-D60G
C370
10
50V
CN302
4P
R370
2.2k
R372
1k
R371
10k
C371
10
50V
Q302
2SC3624A
R373
2.2k
R375
1k
R374
10k
C372
10
50V
R333
2.2k
Q303
2SC3624A
Q301
2SC3624A
C351
R385
2.2k
C376
10
50V
R390
1k
C377
10
50V
Q308
2SC3624A
R391
2.2k
R393
1k
R392
10k
Q309
2SC3624A
52
R341
1k
C343
1
50V
52
R323
47k
Q307
2SC3624A
R388
2.2k
R389
10k
C324
10
50V
R342
1k
0
C323
B
0.001
C304
10 50V
R387
1k
R386
10k
C325
10 50V
R319
R322
4.7k
R320
10k
C322
10 50V
C321
B
0.001
C356
0.001
B
R321 1k
R356
4.7k
C355
B
0.001
47k
47k
C320
10
50V
C354
R354
10 50V
10k
1k
R358
R357
R355
R306
4.7k
B
C306
B
0.001
R304
10k
0.022
1k
47k
47k
B
R308
R307
0.022
C357
10
50V
C366
Q306
2SC3624A
R352
470
C316
R383
10k
R353
10k
R384
1k
C353
220p B
R382
2.2k
R351
47k
Q305
2SC3624A
10 50V
R380
10k
C307
10
50V
C352
220p
B
R305
R379
2.2k
C305
B
0.001
Q304
2SC3624A
R381
1k
C375
10
50V
R336
1k
R334
100k
R378
1k
C374
10
50V
R335
1k
J302
R337
100k
R376
2.2k
R377
10k
C373
10
50V
R340
0
C342
C341
L341
0.1
100
F
16V
C337
0.1
HCD-WZ8D
4–27. Schematic Diagram – VIDEO/MIC Board – • See page 24 for Waveforms.
C701
0.47 50V
C711
0.001
R739
22k
C702
0.47
50V
R738
22k
C710
0.068
10k
R725
C730
R721
R722
1k
C726
JW701
J701
RV701
50k
JW715
R737
120k
C704
0.001
C716
2.2
50V
C709
47 16V
C708
47 16V
EP701
R711
15k
R734
22k
IC701
M65850FP-E1
R736
220
C706
1 50V
D702
UDZSTE-175.1B
R735
22k
CN801
17P
IC801
MM1568AJBE
C821
22 50V
C810
1 50V
C809
1 50V
C808
C732
R727
1k 0.22 50V
10k
RV702
50k
C727
47p
R726
C723
R720
100
IC702(1/2)
NJM4580MD
J702
C736
220
10V
JW711
R710
15k
C715
0.022
C703
0.068
R733
22k
C705
0.0068
C714
1 50V
C713
0.0068
C722
10
50V
R715
10k
R740
22k
R714
10k
R741
47k
C712
0.15
R713
100k
CN701
4P
R712
0
C725
0.01
C724
2.2 50V
0.001
R719
10k
C731
C719
2.2 50V
C728
150k
100k
R718
IC702(2/2)
NJM4580MD
47p
R716
100
100p
R723
C717
10 50V
C721
0.01
R724
C729
1k 0.22 50V
R742
10k
R810
75
FB806
0
R809
75
FB805
0
R808
68
FB804
0
R807
68
FB803
0
J803
C820
100 10V
R802
C819
10k
22 50V
C826
22p
CH
C818
100 10V
1 50V
C817
22 50V
C816
470 6.3V
C804
0.1
F
C815
22 50V
C825
22p
CH
C827
22p
CH
C814
470 6.3V
C807
1 50V
C806
1 50V
C805
1 50V
L801
C813
C803
22
50V
22 50V
C830
R806
68
FB802
0
R805
75
FB801
0
C811
0.1
C802
0.1
F
C801
100
10V
Q801
DTA114EKA
B
J802
C812
470 6.3V
R801
10k
0.1
C824
22p
CH
R803
10k
C829
0.1
B
R804
10k
J801
C822
22p
CH
Q802
DTC114EKA
C823
22p
CH
C828
54
54
0.1
B
HCD-WZ8D
4-28. IC Block Diagrams
RFDC
RFSIN
ATOP
ATON
AIN
AIP
VPA
RFAC
BYP
DIN
DIP
FNP
FNN
VNA
MEV
RX
IC001 CXD1881AR (RF Board)
64 63
62 61 60 59
58
57
56
55 54
53 52
51
50
49
FAST ATTACK
INPUT
SEL
DVDRFP 1
DVDRFN 2
ATT
4
MUX
INPUT
BIAS
ATT
PROGRAMMABLE
EQUALIZER
FILTER
DIFFERENTIATOR
AGC
2
INPUT
IMPEDANCE
SEL
+
CLAMP &
ENVELOPE
–
2
INPUT
IMPEDANCE
SEL
OUTPUT
FULL WAVE
INHIBIT
RECTIFER
FROM S-PORT
AGCO
CONTROL
SIGNALS
TO EACH
BLOCK
BUFFER
2
SIGDET
+
–
LEVEL
DAC
3
COMPARATOR
CE ATT
CEPOL
A2 3
PHASE
DETECTOR
B2 4
GCA
– –
–
+
TOPHOLD
3
3
FROM
FROM VC
S-PORT S-PORT
TOPHOLD
+
+
C
GCA
GCA
LPF
44 LCP
43 LCN
MNTR
CONTROL
42 MNTR
GCA
41 CE
OFFSET
CANSEL
GCA
40 FE
5
FROM
S-PORT
4
FROM
S-PORT
+
+
GCA
B
B 11
–
+
A+D
D
C 10
OFFSET
CANSEL
SDEN
SDATA
SCLK
V33
4
FROM
S-PORT
CP 7
CN 8
D 9
V33 FOR
OUTPUT
BUFFER
PI
FE
TE
CE
V25
V125
V25/3
PHASE
DETECTOR
D2 6
48
47
46
45
SERIAL
PORT
REGISTER
LPF ATT
POL SEL
BUFFER
+
+
EQ
C2 5
AGC
HOLD
AGC CHARGE
PUMP
B+C
A
A 12
MUX
GCA
3
FROM
S-PORT
MUX
GCA
LPF
CD/DVD CP/CN
LOW
IMPEDANCE
B+D
CD D 13
+
+
+
+
GCA
CEFDB
6
FROM
S-PORT
3
FROM
S-PORT
FOR SERVO
OUTPUT
GCA
GCA
4
FROM
S-PORT
3
FROM
S-PORT
HOLDEN
SEL
A+C
3
FROM
S-PORT
CD/DVD
39 TE
38 PI
+
+
CD A 16
TE
RST
5
FROM
S-PORT
SUM
AMP
GCA
W/LPF
OFFSET
CANSEL
OFFSET
CANSEL
GCA
LPF
CD C 14
CD B 15
GCA
SUB
BCA
DET
–
+
TOP
HOLD
FROM 2
DAC
S-PORT
PH
37 V25
36 V125
V25/2
35 TPH
COMPARATOR
–
+
34 DFT
GCA
SEL
33 LINK
VCI FOR SERVO INPUT
LINKEN
HYSTERESISTER
& OFFSET
FROM S-PORT
VC = VPB/2
APC SEL
DVD/CD
DUAL APC
LD H/L
FROM S-PORT
INPUT GAIN
BOTTOM
INPUT
FROM S-PORT
AGCO
ENVELOPE
IMPEDANCE
2
FROM S-PORT SINK CURRENT 2
2
FROM S-PORT
PH
PEAK/BOTTOM
INPUT
HOLD
BUFFER
MUX
MIRR
COMPARATOR
17 18 19 20
21 22
23
24 25 26
27
28 29
30
31
32
CD F
CD E
VPB
VC
DVDLD
CDLD
DVDPD
CDPD
VNB
LDON
MIRR
MP
MB
MLPF
MIN
MEVO
INTERNAL
FDGHG
55
HCD-WZ8D
ML
MC
MDI
MDO
ZERO8
DATA4
ZERO7
NC
VCC1
AGND1
VCC2
AGND2
IC302 PCM1609KPTR (DMB03 Board)
36
35
34
33
32
31
30
29
28
27
26
25
Power Supply
RST 37
SCKI 38
System Clock
Manager
24 VCC3
SCKO 39
DAC
Output Amp and
Low-pass Filter
DAC
Output Amp and
Low-pass Filter
21 AGND4
DAC
Output Amp and
Low-pass Filter
20 VOUT8
DAC
Output Amp and
Low-pass Filter
19 AGND6
23 AGND3
22 VCC4
BCK 40
Serial
Input
I/F
TEST 42
Enhanced
Multi-level
Delta-Sigma
Modulator
8x
Oversampling
Digital Filler
with
Function
Controller
LRCK 41
VDD 43
DGND 44
DATA1 45
Function
Control
I/F
DATA2 46
DATA3 47
DAC
Output Amp and
Low-pass Filter
DAC
Output Amp and
Low-pass Filter
DAC
Output Amp and
Low-pass Filter
DAC
Output Amp and
Low-pass Filter
18 VCC5
17 AGND5
16 VOUT7
15 VCOM
14 VOUT1
13 VOUT2
ZERO2/GPO2
ZERO3/GPO3
ZERO4/GPO4
ZERO5/GPO5
7
8
9
10 11 12
VOUT3
ZERO1/GPO1
6
VOUT4
5
VOUT5
4
VOUT6
3
NC
2
ZERO6/GPO6
1
NC
Zero Detect
ZEROA 48
AGND
VCC
C PR
C NR
C PR
C NR
VDD
DGND
SYSCLK
DOUT
BCK
LRCK
IC352 PCM1800E/2K (DMB03 Board)
24
23
22
21
20
19
18
17
16
15 14 13
DIGITAL ∑
MODULATOR
DIGITAL ∑
MODULATOR
56
1
2
3
4
5
6
7 8 9
10 11 12
V REF 2
RIN
RSTB
BYPASS
FMT0
FMT1
MODE0
MODE1
FSYNC
CLOCK/
TIMING CONTROL RESET/
POWER CONTROL
REFCOM
SINGLE-END
DEFERENTIAL
CONVERTER
V REF 1
REFERENCE
SERIAL I/O
INTERFACE
&
MODE/FORMAT
CONTROL
LIN
SINGLE-END
DEFERENTIAL
CONVERTER
1/64
DECIMATION
FILTER
&
LOW-CUT
FILTER
HCD-WZ8D
IC216 SN74ALVCH16841DGGR (DMB03 BOARD)
1OE
1
OE
LE
56 1LE
1D1
1D2
2
3
55 1Q1
54 1Q2
GND
4
53 GND
1D3
1D4
5
6
52 1Q3
51 1Q4
VCC
7
1D5
1D6
8
9
GND
10
47 GND
1D7
1D8
1D9
1D10
11
12
13
14
46
45
44
43
2D1
2D2
2D3
15
16
17
42 2Q1
41 2Q2
40 2Q3
GND
18
39 GND
2D4
2D5
2D6
19
20
21
38 2Q4
37 2Q5
36 2Q6
VCC
22
50 VCC
LATCH
49 1Q5
48 1Q6
1Q7
1Q8
1Q9
1Q10
35 VCC
2D7
2D8
23
24
34 2Q7
33 2Q8
GND
25
32 GND
2D9
2D10
26
27
31 2Q9
30 2Q10
2OE 28
OE
LE
29 2LE
XUGF
GFS
EMPH
WFCK
XTAI
XTAO
XTSL
V16M
VPCO
VCTL
ERROR
CORRECTOR
FSTO
CM4
RFAC
ASYI
ASYO
ASYE
BIAS
CLOCK
GENERATOR
ASYMMETRY
CORRECTOR
XPCK
FILO
FILI
PCO
CLTV
DIGITAL
PLL
MDP
LOCK
PWMI
DIGITAL
CLV
SENS
DATA
XLAT
CLOK
SCOR
SBSO
EXCK
SCSY
SQSO
SQCK
D/A
INTERFACE
EFM
DEMODURATOR
32K
RAM
DIGITAL
OUT
TES1
TEST
XRST
MD2
DOUT
SUB CODE
PROCESSOR
CPU
INTERFACE
SERVO
AUTO
INTERFACE
SERVO BLOCK
RFDC
CE
TE
SE
FE
VC
IGEN
SERVO
INTERFACE
SOUT
SOCK
XOLT
SCLK
COUT
SSTP
ATSK
MIRR
DFCT
FOK
MIRR
DFCT
FOK
SERVO DSP
OPAMP
A/D
ANALOG SW CONVERTER
PWM GENERATOR
FOCUS
SERVO
FOCUS PWM
GENERATOR
FFDR
FRDR
TRACKING
SERVO
TRACKING PWM
GENERATOR
TFDR
TRDR
SLED
SERVO
SLED PWM
GENERATOR
SFDR
SRDR
ADIO
LATCH
WDCK
C2PO
LRCK
PCMD
BCLK
MUTE
IC509 CXD3068Q (DMB03 Board)
57
HCD-WZ8D
40 – 36
35 34 33
REFRESH
CONTROL
CLOCK
TIMING
GENERATOR
VSS
44 43 42 41
A9
A8
A7
A6
A5
A4
DQ12
DQ11
DQ10
DQ9
45
OE
VSS
49 48 47 46
UCAS
DQ16
DQ15
DQ14
DQ13
NC
50
LCAS
VSS
IC706 MSM51V18165F-60TSKR1 (DMB03 Board)
32 31 30 29 28 27
26
INTERNAL
ADDRESS
COUNTER
I/O
CONTROLLER
INPUT
BUFFER
OUTPUT
BUFFER
INPUT
BUFFER
I/O
CONTROLLER
COLUMN
ADDRESS
BUFFERS
I/O
SELECTOR
OUTPUT
BUFFER
SENSE
AMPLIFIER
COLUMN
DECODERS
MEMORY
CELLS
VDD
11 – 16
DQ1
DQ2
DQ3
DQ4
VCC
DQ5
DQ6
DQ7
DQ8
NC
ON CHIP
IVCC GENERATOR
VDD
VDD
17 18
19 20
21 22 23 24
25
VDD
7 8 9 10
VDD
A0
A1
A2
A3
6
ON CHIP
VBB GENERATOR
NC
NC
2 3 4 5
ROW
DECODERS
WORD
DRIVERS
WE
RAS
1
VDD
VCC
ROW
ADDRESS
BUFFERS
IC903 BR24C16F-E2 (DMB03 Board)
VCC 8
1 A0
16 K bit EEPROM ARRAY
11 bit
TEST 7
ADDRESS
DECODER
8 bit
11 bit
START
SLAVE WORD
ADDRESS REGISTER
DATA
REGISTER
2 A1
STOP
SCL 6
3 A2
CONTROL CIRCUIT
ACK
SDA 5
58
HIGHT VOLTAGE
GENERATOR
POWER SUPPLY
VOLTAGE DETECTION
4 GND
HCD-WZ8D
VCC
PR
CLR
Q
8
7
6
5
S
R
Q
C
D
Q
1
2
3
4
CK
D
Q
GND
IC904 TC7W74FK-TE85L (DMB03 Board)
IC202 BA6956AN (MAIN Board)
TSD
IC903 SI-8033JF (REGULATOR Board)
ON/OFF
SOFT
START
COMPARATOR
+
–
+
–
8
9
RIN
OUT1
7
GND
RNF
6
FIN
OUT2
5
VCC
4
VM
3
OVER
CURRENT
PROTECTOR
REGULATOR
LATCH
&
DRIVER
RESET
OSC
2
IC913 SI-8050JF (REGULATOR Board)
OVER
CURRENT
PROTECTOR
REGULATOR
1
VREF
CONTROL LOGIC
OSC
+
–
OVER HEAT
PROTECTOR
COMPARATOR
+
–
ERROR AMP
VREF
OVER HEAT
PROTECTOR
1
2
3
4
5
1
2
3
4
5
SW OUT
GND
VOS
ON/OFF
VIN
SW OUT
GND
VOS
S.S
VREF
VIN
ERROR AMP
LATCH
&
DRIVER
RESET
59
HCD-WZ8D
IC801 MM1568AJBE (VIDEO Board)
VCC1
1
CIN
2
MUTE1
3
VIN
4
34 VCC2
BIAS
4dB
LPF
4dB
LPF
75Ω
DRIVER
2dB
75Ω
DRIVER
33 COUT
CLAMP
32 GND2
+
YC MIX
2dB
31 VOUT
5
30 VSAG
CLAMP
YIN
6
BIAS
7
GND1
8
NC
9
29 GND2
LPF
4dB
75Ω
DRIVER
2dB
28 YOUT
BIAS
27 YSAG
GND1 10
NC 11
26 GND2
CYIN 12
LPF
4dB
75Ω
DRIVER
2dB
CLP 13
25 CYOUT
24 CYSAG
BIAS
CLAMP
23 GND2
CbIN 14
4dB
LPF
2dB
BIAS
MUTE2 15
75Ω
DRIVER
22 CbOUT
21 CbSAG
CrIN 16
20 GND2
LPF
4dB
BIAS
GND2 17
75Ω
DRIVER
2dB
19 CrOUT
18 CrSAG
NC
VCC
CLOCK
REF
OP2 IN
OP2 OUT
LPF2 IN
LPF2 OUT
IC701 M65850FP-E1 (MIC Board)
16
15
14
13
12
11
10
9
OSCILLATOR
LPF2
D/A
1/2 Vcc
DO1
CLOCK
MO
AUTO
RESET
RESET
MAIN CONTROL
D1
20Kbit/
SRAM
MI
DO0
A/D
60
1
2
3
4
5
6
7
8
NC
LPF1 IN
LPF1 OUT
OP1 OUT
OP1 IN
CC1
CC2
GND
LPF1
HCD-WZ8D
4-29. IC Pin Function Description
• IC207 ZIVA5X-C1F (DVD SYSTEM PROCESSOR)(DMB03 BOARD)
Pin No.
Pin Name
I/O
Description
1
VDDP
—
Power supply terminal (+3.3V)(I/O signal)
2
HA1
I/O
Address bus
3
HAD15
I/O
Data bus (address signal multiplexed)
4
HAD14
I/O
Data bus (address signal multiplexed)
5
HAD13
I/O
Data bus (address signal multiplexed)
6
HAD12
I/O
Data bus (address signal multiplexed)
7
HAD11
I/O
Data bus (address signal multiplexed)
8
HAD10
I/O
Data bus (address signal multiplexed)
9
HAD9
I/O
Data bus (address signal multiplexed)
10
HAD8
I/O
Data bus (address signal multiplexed)
11
HAD7
I/O
Data bus (address signal multiplexed)
12
VDDP
—
Power supply terminal (+3.3V)(I/O signal)
13
GNDP
—
Ground terminal (I/O signal)
14
HAD6
I/O
Data bus (address signal multiplexed)
15
HAD5
I/O
Data bus (address signal multiplexed)
16
HAD4
I/O
Data bus (address signal multiplexed)
17
HAD3
I/O
Data bus (address signal multiplexed)
18
HAD2
I/O
Data bus (address signal multiplexed)
19
HAD1
I/O
Data bus (address signal multiplexed)
20
VDDP
—
Power supply terminal (+3.3V)(I/O signal)
21
GNDP
—
Ground terminal (I/O signal)
22
HAD0
I/O
Data bus (address signal multiplexed)
23
HDTACK
I/O
Acknowledge signal input/output for host data transfer (not used)
24
HIRQ0
I
25
WEH.UDS
I/O
Host upper data strobe signal output
26
WEL.LDS
I/O
Host lower data strobe signal output (not used)
27
HREAD
I/O
Read/write strobe signal output
28
GPIO0
I/O
Jig detection port (pull-up)
29
GND
—
Ground terminal (inside core)
30
VDD
—
Power supply terminal (+1.8V)(inside core)
31
GND25
—
Ground terminal (SDRAM I/O signal)
32
VDD25
—
Power supply terminal (+3.3V)(SDRAM I/O signal)
33
MA9
O
SDRAM address bus
34
MA8
O
SDRAM address bus
35
MA7
O
SDRAM address bus
36
MA6
O
SDRAM address bus
37
MA5
O
SDRAM address bus
38
MA4
O
SDRAM address bus
39
MA3
O
SDRAM address bus
40
MA2
O
SDRAM address bus
41
MA1
O
SDRAM address bus
42
MA0
O
SDRAM address bus
43
GND25
—
Ground terminal (SDRAM I/O signal)
44
VDD25
—
Power supply terminal (+3.3V)(SDRAM I/O signal)
45
MA10
O
SDRAM address bus
46
MA11
O
SDRAM address bus
47
BA1
O
SDRAM bank select 1 signal output
48
BA0
O
SDRAM bank select 0 signal output
49
MCS0
O
SDRAM chip select 0 signal output
50
MCS1
O
Not used
Interrupt signal input for Medusa (not used)
61
HCD-WZ8D
Pin No.
Pin Name
I/O
Description
51
MRAS
O
SDRAM row address strobe signal output
52
MCAS
O
SDRAM column address strobe signal output
53
MWE
O
SDRAM write enable signal output (“H” : read, “L” : write)
54
GND25
—
Ground terminal (SDRAM I/O signal)
55
VDD25
—
Power supply terminal (+3.3V)(SDRAM I/O signal)
56
MCLK
O
SDRAM Clock output
57
MD0
I/O
SDRAM data
58
MD1
I/O
SDRAM data
59
MD2
I/O
SDRAM data
60
MD3
I/O
SDRAM data
61
GND25
—
Ground terminal (SDRAM I/O signal)
62
MDQM0
O
Byte read /write mask signal 0 output
63
VDD25
—
Power supply terminal (+3.3V)(SDRAM I/O signal)
64
MD4
I/O
SDRAM data
65
MD5
I/O
SDRAM data
66
MD6
I/O
SDRAM data
67
MD7
I/O
SDRAM data
68
MD8
I/O
SDRAM data
69
MD9
I/O
SDRAM data
70
MD10
I/O
SDRAM data
71
MD11
I/O
SDRAM data
72
GND25
—
Ground terminal (SDRAM I/O signal)
73
MDQM1
O
Byte read /write mask signal 1 output
74
VDD25
—
Power supply terminal (+3.3V)(SDRAM I/O signal)
75
MD12
I/O
SDRAM data
76
MD13
I/O
SDRAM data
77
MD14
I/O
SDRAM data
78
MD15
I/O
SDRAM data
79
GND
—
Ground terminal (inside core)
80
VDD
—
Power supply terminal (+1.8V)(inside core)
81
MD16
I/O
SDRAM data
82
MD17
I/O
SDRAM data
83
MD18
I/O
SDRAM data
84
MD19
I/O
SDRAM data
85
GND25
—
Ground terminal (SDRAM I/O signal)
86
MDQM2
O
Byte read /write mask signal 2 output
87
VDD25
—
Power supply terminal (+3.3V)(SDRAM I/O signal)
88
MD20
I/O
SDRAM data
89
MD21
I/O
SDRAM data
90
MD22
I/O
SDRAM data
91
MD23
I/O
SDRAM data
92
MD24
I/O
SDRAM data
93
MD25
I/O
SDRAM data
94
MD26
I/O
SDRAM data
95
MD27
I/O
SDRAM data
96
GND25
—
Ground terminal (SDRAM I/O signal)
97
MDQM3
O
Byte read /write mask signal 3 output
98
VDD25
—
Power supply terminal (+3.3V)(SDRAM I/O signal)
99
MD28
I/O
SDRAM data
100
MD29
I/O
SDRAM data
62
HCD-WZ8D
Pin No.
Pin Name
I/O
Description
101
MD30
I/O
SDRAM data
102
MD31
I/O
SDRAM data
103
GND25
—
Ground terminal (SDRAM I/O signal)
104
VDD25
—
Power supply terminal (+3.3V)(SDRAM I/O signal)
105
VCLK
I/O
System clock (not used)
106
XCK_I/O_SEL
I/O
5.1ch/downmix switch signal output
107
VS
O
S1 signal output (not used)
108
I/P SW
O
Progressive/interlace switch signal output (not used)
109
CDSEL
O
CD-DA selection signal output (not used)
110
MREQ
O
Audio muting request signal output
111
VDDP
—
Power supply terminal (+3.3V)(I/O signal)
112
GNDP
—
Ground terminal (I/O signal)
113
MDI
O
Serial data output to the D/A converter (IC302)
114
MC
O
Serial data clock output to the D/A converter (IC302)
115
ML
O
Latch enable signal output to the D/A converter (IC302)
Busy signal input from the EEPROM (IC204)
116
HIRQ2_
I
117
VDAC_4B
—
Video DAC bias bit 4 (connected to the ground)
118
VDAC_VDD4
—
Power supply terminal (+3.3V)(Video DAC 4)
119
VDAC_4
O
VDAC output 4
120
VDAC_3B
—
Video DAC bias bit 3 (connected to the ground)
121
VDAC_VDD3
—
Power supply terminal (+3.3V)(Video DAC 3)
122
VDAC_3
O
VDAC output 3
123
VDAC_2B
—
Video DAC bias bit 2 (connected to the ground)
124
VDAC_VDD2
—
Power supply terminal (+3.3V)(Video DAC 2)
125
VDAC_2
O
VDAC output 2
126
VDAC_1B
—
Video DAC bias bit 1 (connected to the ground)
127
VDAC_VDD1
—
Power supply terminal (+3.3V)(Video DAC 1)
128
VDAC_1
O
VDAC output 1 (not used)
129
VDAC_0B
—
Video DAC bias bit 0 (connected to the ground)
130
VDAC_VDD0
—
Power supply terminal (+3.3V)(Video DAC 0)
131
VDAC_0
O
VDAC output 0
132
VDAC_DVSS
—
Ground terminal (Video DAC digital system)
133
VDAC_DVDD
—
Power supply terminal (+3.3V)(Video DAC digital system)
134
VDAC_REFVDD
—
Power supply terminal (Video DAC reference)
135
VDAC_REF
I
136
VDAC_REFVSS
—
Ground terminal (Video DAC reference)
137
XVSS
—
Ground terminal (crystal oscillator)
138
XOUT
O
Crystal oscillation signal output (not used)
Crystal oscillation signal input
Reference voltage input terminal(for Video DAC)
139
XIN
I
140
XVDD
—
Power supply terminal (crystal oscillator)
141
AVSS2
—
Ground terminal (analog PLL)
142
AVDD2
—
Power supply terminal (+3.3V)(analog PLL)
143
AVDD1
—
Power supply terminal (+3.3V)(analog PLL)
144
AVSS1
—
Ground terminal (analog PLL)
145
VDD
—
Power supply terminal (+1.8V)(inside core)
146
GND
—
Ground terminal (inside core)
147
XCK
O
Audio system clock output
148
LRCK
O
LRCK signal output for audio
149
BCK
O
BCK signal output for audio
150
DATA0(DM)
O
Audio data(Down Mix signal) output
63
HCD-WZ8D
Pin No.
Pin Name
151
DATA1(FLR)
O
Audio data(Front L/R signal) output
152
VDDP
—
Power supply terminal (+3.3V)(I/O signal)
153
GNDP
—
Ground terminal (I/O signal)
154
DATA2(SLR)
O
Audio data(Rear L/R signal) output
155
DATA3(CSW)
O
Audio data(Center/Subwoofer signal) output
156
IEC958
O
S/PDIF signal (not used)
157
DAI_DATA
I
Data input from ADC (not used)
158
DAI_BCK
I
BCK signal input from ADC (not used)
159
DAI_LRCK
I
LRCK signal input from ADC (not used)
160
I2C_CL
I/O
I2C clock bus
161
I2C_DA
I/O
I2C data bus
162
CS(ZIVA_E2P)
O
Chip select signal output to the EEPROM (IC204)
163
RXD1
I
Serial data input for check jig
164
TXD1
O
Serial data output for check jig
165
WRITE_CTRL(ZIVA_E2P)
O
Write control signal output to the EEPROM (IC204)
166
GNDP
—
Ground terminal (I/O signal)
167
VDDP
—
Power supply terminal (+3.3V)(I/O signal)
168
SDDATA7
I
SDBus data7 input
169
SDDATA6
I
SDBus data6 input
170
SDDATA5
I
SDBus data5 input
171
SDDATA4
I
SDBus data4 input
172
GND
—
Ground terminal (inside core)
173
VDD
—
Power supply terminal (+1.8V)(inside core)
174
SDDATA3
I
SDBus data3 input
175
SDDATA2
I
SDBus data2 input
176
SDDATA1
I
SDBus data1 input
177
SDDATA0
I
SDBus data0 input
178
SDREQ
O
SDBus data request signal output
179
SDEN
I
SDBus data enable signal input
180
GNDP
—
Ground terminal (I/O signal)
181
VDDP
—
Power supply terminal (+3.3V)(I/O signal)
182
SDERROR
I
SDBus data error signal input
183
SDCLK
I
SDBus data clock input
184
HIRQ1
I
Interrupt signal input from the mechanism controller (IC901)
185
DRVCLK
I
Serial data clock input from the mechanism controller (IC901)
186
DRVTX
I
Serial data input from the mechanism controller (IC901) and the EEPROM (IC204)
187
DRVRX
O
Serial data output to the mechanism controller (IC901) and the EEPROM (IC204)
188
DRVRDY
I
Ready signal input from the mechanism controller (IC901)
189
VNW
—
Power supply for 5V tolerance voltage input
190
ALE
O
Latch enable signal output for address data demux
191
RST_SPC
O
Reset signal output to the mechanism controller (IC901)
192
INT/EXT
O
Input selection signal output for SDBus or ADC
193
HCS2
O
Chip select signal output for Medusa (not used)
194
HCS1
I/O
195
HCS0
O
Chip select signal output to the external ROM (IC206)
196
VDDP
—
Power supply terminal (+3.3V)(I/O signal)
197
TRST
I
Reset signal input
198
TDO
O
Data output
199
TDI
I
Data input
200
TMS
I
TMS signal input
64
I/O
Description
Not used
HCD-WZ8D
Pin No.
Pin Name
I/O
Description
201
TCK
I
TCK signal input
202
RESET
I
ZIVA reset input
203
BUS CLK
I/O
Not used
204
GND
—
Ground terminal (inside core)
205
VDD
—
Power supply terminal (+1.8V)(inside core)
206
HA3
I/O
Address bus 3
207
HA2
I/O
Address bus 2
208
GNDP
—
Ground terminal (I/O signal)
65
HCD-WZ8D
• IC401 M30622MGN-B22FP (AEP, UK, RU, E2, MX) , -B12FP (EXCEPT AEP, UK, RU, E2, MX)(SYSTEM CONTROL)(MAIN BOARD)
Pin No.
Pin Name
I/O
Description
1
MIC-CHECK
I
2
NO USE
—
Not used
3
NO USE
—
Not used (connected to the ground)
Microphone detection signal input
4
SIRCS
I
SIRCS signal input fromthe remote sensor (IC601)
5
DSP DIN
O
Serial data output to the DSP (IC601)
6
DSP DOUT
I
Serial data input from the DSP (IC601)
7
DSP CLK
O
Serial clock output to the DSP (IC601)
8
BYTE
—
External data bus width selection terminal
Processor modes switch terminal
9
CN VSS
—
10
XC-IN
I
Sub clock input terminal (32.768kHz)
11
XC-OUT
O
Sub clock output terminal (32.768kHz)
12
RESET
I
System reset signal input
13
X-OUT
O
Main system clock output terminal (16MHz)
14
VSS
—
Ground terminal
15
X-IN
I
16
VCC
—
17
NMI
I
NMI input terminal (fixed at “H”)
18
RDS INT
I
RDS INT signal input
19
NO USE
—
Main system clock input terminal (16MHz)
Power supply terminal (+3.3V)
Not used (connected to the ground)
20
AC-CUT
I
AC cut detection signal input
21
DSP XRST
O
Reset signal output to the DSP (IC601)(“L” : reset)
22
DSP HCE
O
Chip select signal output to the DSP (IC601)
23
DSP BST
O
Boot strap signal output to the DSP (IC601)
24
DSP ACK
I
Acknowledge signal input from the DSP (IC601)
25
DSP ERROR
I
ERROR signal input from the DSP (IC601)
26
DSP EXLOCK
O
PLL lock error and data error flag signal output to the DSP (IC601)
27
DSP PM
O
PLL reset signal output to the DSP (IC601)
28
DSP DECODE
—
Not used
29
IIC-CLK
O
IIC serial clock output
30
IIC-DATA
O
IIC serial data output
31
NO USE
—
Not used (connected to the ground)
32
NO USE
—
Not used (connected to the ground)
33
A-MUTE
O
Audio muting signal output
34
SOFT-TEST
—
Soft test teminal
35
MUTE REQ
I
Audio muting request signal input from the DVD system processor (IC207)
36
IF-VIDEO MUTE2
O
Video muting signal output
37
IF-VIDEO MUTE1
O
Video muting signal output
38
IF-DVD-RESET
O
System reset signal output to the DVD system processor (IC207)
39
IF-DVD-POWER
O
DVD power supply control signal output (“H” : on, “L” : off)
40
RDS-DATA
I
RDS data input
41
ST-MUTE
O
Muting signal output to the tuner
42
STEREO
I
Stereo detection signal input from the tuner (“L” : in, “H” : off)
43
TUNED
I
Tuner tuned status signal input from the tuner (“L” : in, “H” : off)
44
ST-CE
O
Tuner chip enable signal output to the tuner
45
ST-DOUT
O
Data output to the tuner
46
ST-DIN
I
Data input from the tuner
47
ST-CLK
O
Clock output to the tuner
48
SW MUTE
O
Sub woofer muting signal output
49
VR-CLK
O
Clock output to the audio signal processor (IC301)
50
VR-DATA
Oº
Data output to the audio signal processor (IC301)
66
HCD-WZ8D
Pin No.
Pin Name
I/O
Description
51
VOL-CLK
O
Clock output to the audio signal processor (IC101)
52
VOL-DATA
O
Data output to the audio signal processor (IC101)
53
CN CHECK
I
Connection check signal input (from DXA-WZ8D)
54
AMS-IN
I
AMS signal input (“L” : in, “H” : off)(from DXA-WZ8D)
55
TC LINE-MUTE
O
TC line muting signal output (“H” : on, “L” : off)(to DXA-WZ8D)
56
ALC
O
ALC signal output (“L” : on, “H” : off)(to DXA-WZ8D)
57
TC REC-MUTE
O
TC REC muting signal output (“L” : on, “H” : off)(to DXA-WZ8D)
58
IO-EXP DATA OUT
O
Data output to the I/O expander (IC251, DXA-WZ8D)
59
IO-EXP DATA IN
I
Data input from the I/O expander (IC251, DXA-WZ8D)
60
IO-EXP LAT
O
Latch signal output to the I/O expander (IC251, DXA-WZ8D)
61
IO-EXP CLK
O
Clock output to the I/O expander (IC251, DXA-WZ8D)
62
VCC
—
Power supply terminal
63
HEAD-PHONE IN
I
64
VSS
—
Ground terminal
65
STK MUTE
O
Muting signal output to the power amplifier (to DXA-WZ8D)
66
TA MUTE
O
TA line muting signal output (“H” : on, “L” : off)(to DXA-WZ8D)
67
VOL-A
I
Encoder signal input from the volume encoder
Headphone detection signal input
68
VOL-B
I
Encoder signal input from the volume encoder
69
LED -TUNER/BAND
O
TUNER/BAND LED control signal output
70
LED-DVD
O
DVD LED control signal output
71
LED-AROUND PLAY
O
PLAY LED control signal output
72
LED-TAPE A/B
O
TAPE A/B LED control signal output
73
DISPLAY KEY
I
DISPLAY key signal input
74
POWER KEY
I
POWER key signal input
75
LED-MD (VIDEO)
O
MD (VIDEO) LED control signal output
76
LED-STANDBY
O
STANDBY LED control signal output
77
HP/REC OUT MUTE
O
Headphone/line out muting signal output (“L” : on, “H” : off)
78
BACK-LIGHT 3
O
LCD back light 3 LED control signal output (blue)
79
BACK-LIGHT 2
O
LCD back light 2 LED control signal output (green)
80
BACK-LIGHT 1
O
LCD back light 1 LED control signal output (red)
81
LCD-DATA
O
Data output to the liquid crystal display
82
LCD-CLK
O
Clock output to the liquid crystal display
83
LCD-ENB
O
Chip select signal output to the liquid crystal display
84
LCD-RS
O
Reset signal output to the liquid crystal display
85
LOAD-OUT
O
Loading motor control signal output
86
LOAD-IN
O
Loading motor control signal output
87
OPEN-SW
I
OPEN switch signal input
88
CLOSE-SW
I
CLOSE switch signal input
89
A SHUT
I
Reel pulse signal input from the deck A (from DXA-WZ8D)
90
B SHUT
I
Reel pulse signal input from the deck B (from DXA-WZ8D)
91
A TRG
O
Trigger control signal output to the deck A (“H” : on)(to DXA-WZ8D)
92
B TRG
O
Trigger control signal output to the deck B (“H” : on)(to DXA-WZ8D)
93
SPEC-IN
I
Spec setting terminal
94
AD-KEY2
I
Key input 2 (A/D)
95
AD-KEY1
I
Key input 1 (A/D)
96
AVSS
—
97
VACS IN
I
98
VREF
—
Voltage reference terminal (A/D converter)
99
AVCC
—
Power supply terminal (A/D converter)
100
LCD RESET
O
Reset signal output to the liquid crystal display
Ground terminal (A/D converter)
VACS signal input
67
HCD-WZ8D
• IC901 CXP973064-226R (MECHANISM CONTROLLER)(DMB03 BOARD)
Pin No.
Pin Name
I/O
Description
1
NO USE
O
Not used
2
SDEN
O
Serial data enable signal output to DVD/CD RF amplifier
3
DOCTRL/
ISBTEST
O
Digital out on/off control signal output to the digital signal processor
“L”: digital out off, “H”: digital out on
4
XPST 2753
O
Not used
5
SDA EEP
I/O
6
MNT1
I
EEPROM ready signal input from the DVD decoder
7
FCS JMP 1
O
Focus jump 1 signal output to the motor/coil driver
8
FCS JMP 2
O
Focus jump 2 signal output to the motor/coil driver
9
SENS CD
I
Internal status (SENSE) signal input from the digital signal processor
10
CDSP2
O
Loading motor drive signal (loading in direction) output terminal
11
CDSP4
O
Loading motor drive signal (loading out direction) output terminal
12
XCS DVD
O
Chip select signal output to the DVD decoder
13
VSS
—
Ground terminal (digital system)
14 to 21
D0 to D7
I/O
Two-way data bus with the DVD decoder
22
INIT0 DVD
I
Interrupt signal input from the DVD decoder
23
INIT1 DVD
I
Interrupt signal input from the DVD decoder
24
MSCK SAMBA
O
Serial data transfer clock signal output to the DSD decoder
25
XRST 1882
O
Reset signal output to the DVD decoder “L”: reset
Two-way data bus with the EEPROM
26
SCOR
I
Subcode sync (S0+S1) detection signal input from the digital signal processor
27
LAT CD
O
Serial data latch pulse signal output to the digital signal processor
28
LD ON
O
Laser diode on/off control signal output to the DVD/CD RF amplifier
“L”: laser diode off, “H”: laser diode on
29
MIRR
I
Mirror signal input from the digital signal processor
30
COUT CD
I
Numbers of track counted signal input from the digital signal processor
31
INLIM
I
Detection signal input from limit in switch The optical pick-up is inner position when “H”
32
CS ZIVA
O
Chip select signal output to the DVD system processor
33
SI ZIVA
I
Serial data input from the DVD system processor
34
SO ZIVA
O
Serial data output to the DVD system processor
35
SCK ZIVA
O
Serial data transfer clock signal output to the DVD system processor
36
DRVIRQ
O
Interrupt request signal output to the DVD system processor
37
DRVRDY
O
Ready signal output to the DVD system processor
38
RST
I
System reset signal input from the DVD system processor
39
VSS
—
40
XTAL
I
System clock input terminal (20 MHz)
41
EXTAL
O
System clock output terminal (20 MHz)
42
VDD
—
Power supply terminal (+3.3V) (digital system)
43, 44
SLED A, SLED B
O
Sled motor drive signal output
45
SCK DSD
O
Output terminal for offset adjustment of APEO
46
SDOUT DSD
O
Serial data output to the DSD decoder
47
SDIN DSD
I
Serial data input from the DSD decoder
48
READY DSD
I
Ready signal input from the DSD decoder
49
DATA CD
O
Serial data output to the digital signal processor
50
CLOK CD
O
Serial data transfer clock signal output to the digital signal processor
51
XMSLAT
O
Serial data latch pulse signal output to the DSD decoder
“L”: reset
Ground terminal (digital system)
“L”: ready
52
SQSO
I
Subcode Q data input from the digital signal processor
53
MUTE DSD
O
Muting on/off control signal output to the DSD decoder
54
SQCK
O
Subcode Q data reading clock signal output to the digital signal processor
55
VSS
—
Ground terminal (digital system)
56
CONTROL 4
I
68
Disc tray in detection signal input terminal Not used
“H”: muting on
HCD-WZ8D
Pin No.
Pin Name
I/O
Description
57
CONTROL 2
I
Disc tray out detection signal input terminal Not used
58
GFS DVD
I
Guard frame sync signal input from the DVD decoder
59
MUTE CD
O
Muting on/off control signal output to the digital signal processor
60
MUTE 2D
O
Muting on/off control signal output to the motor/coil driver “H”: muting on
61
SLED
I
Sled motor servo drive PWM signal input terminal
“H”: muting on
62
FG
I
Spindle motor control signal input
63
SP ON
O
Muting on/off control signal output to the motor/coil driver “H”: muting on
64
JIT
I
Jitter signal input
65
TE
I
Tracking error signal input from the DVD/CD RF amplifier
66
PI
I
Pull in signal input from the DVD/CD RF amplifier
Focus error signal input from the DVD/CD RF amplifier
67
FE
I
68
AVSS
—
69
AVREF
I
70
AVDD
—
71
GFS CD
I
Guard frame sync signal input from the digital signal processor
72
SCLK CD
O
SENSE serial data reading clock signal output to the digital signal processor
73
TSD
O
Thermal shut down signal output to the motor/coil driver
74
FOK CD
I
Focus OK signal input from the digital signal processor
75
LOCK CD
I
GFS is sampled by 460 Hz “H” input when GFS is “H”
76
LDSEL
O
Laser diode selection signal output
77
SACD/DVD
O
“SACD/DVD selection signal output “L”: DVD, “H”: SACD”
78
I2C SIO
I/O
Communication data bus with the DVD system processor and system controller
79
I2C SCL
I/O
Communication data reading clock signal input or transfer clock signal output with the DVD system processor
and system controller
80
RXD
I
Serial data input from the RS-232C (for check)
81
TXD
O
Serial data output to the RS-232C (for check)
82
SDCLK RF
O
Serial data transfer clock signal output to the DVD/CD RF amplifier
83
SDATA RF
I/O
Two-way data bus with the DVD/CD RF amplifier
84
XWR
O
Write strobe signal output to the DVD decoder
Ground terminal (for A/D converter)
Reference voltage input terminal (for A/D converter)
Power supply terminal (+3.3V) (for A/D converter)
85
XRD
O
Read strobe signal output to the DVD decoder
86
(PWE)
—
Not used
87
VDD
—
Power supply terminal (+3.3V) (digital system)
88
VSS
—
Ground terminal (digital system)
89 to 96
A0 to A7
O
Address signal output to the DVD decoder
97
DSAVE
O
Motor/coil driver power save control signal output terminal
98
XDRST
O
Reset signal output to the digital signal processor and DSD decoder
99
WP EEP
O
Write protect signal output to the EEPROM
100
SCL EEP
O
Clock signal output to the EEPROM
“L”: reset
69
HCD-WZ8D
SECTION 5
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may have •
some differences from the original one.
• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
• The mechanical parts with no reference number in
the exploded views are not supplied.
• Hardware (# mark) list and accessories and packing
materials are given in the last of this parts list.
Abbreviation
AUS : Australian model
E2 : 120V AC area in E model
E3 : 240V AC area in E model
E15 : 220-240V AC area in E model
EA : Saudi Arabia model
KR : Korean model
MY : Malaysia model
PH : Philippines model
RU
SP
TH
: Russian model
: Singapore model
: Thai model
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
5-1. Front Panel Section
DVD mechanism section
(CDM77B-DVBU20)
#1
14
15
#1
13
14
5
12
11
10
LCD201
5
#1
9
5
8
7
S601
5
2
6
5
#1
1
3
4
including S601
Ref. No.
Part No.
Description
1
2
3
3
3
4-244-435-01
4-244-423-01
X-4955-363-1
X-4955-377-1
X-4955-390-1
KNOB (VOLUME)
BUTTON (CURSOR)
PANEL ASSY, FRONT (AEP, UK)
PANEL ASSY, FRONT (E2)
PANEL ASSY, FRONT
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
3
4
5
6
7
X-4955-723-1
1-687-205-11
4-951-620-01
1-687-207-11
A-4732-210-A
PANEL ASSY, FRONT (RU)
ENTER-SW BOARD
SCREW (2.6X8), +BVTP
CD-TC BOARD
PANEL BOARD, COMPLETE (EXCEPT TH)
7
A-4734-616-A PANEL BOARD, COMPLETE (TH)
70
Remarks
Ref. No.
Part No.
Description
8
9
10
11
12
1-773-185-11
1-687-204-11
4-244-431-02
4-244-430-01
A-4732-447-A
WIRE (FLAT TYPE) (23CORE)
BACK LIGHT BOARD
SHEET (LCD)
HOLDER (LCD)
LCD BOARD, COMPLETE (EXCEPT TH)
12
13
14
15
LCD201
A-4734-602-A
4-244-434-11
3-363-099-11
4-244-441-11
1-805-136-11
LCD BOARD, COMPLETE (TH)
PANEL, LOADING
SCREW (CASE 3 TP2)
CASE
DISPLAY PANEL, LIQUID CRYSTAL
#1
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
Remarks
HCD-WZ8D
5-2. Chassis Section (1/2)
not supplied
#1
61
62
#1
#1
63
60
59
#1
#2
#1
#1
56
#1
57
55
65
64
58
67
66
71
not supplied
#1
#3
68
53
54
69
not supplied
#1
#1
52
#1
70
51
not supplied
Ref. No.
51
52
52
52
53
53
53
53
54
54
54
Part No.
Description
Remarks
4-238-994-11 KNOB (MIC)
(E2, E3, E15, EA, MY, SP, KR, TH, PH, AUS)
A-4732-216-A MIC BOARD, COMPLETE (E2)
A-4732-322-A MIC BOARD, COMPLETE
(E3, E15, EA, MY, SP, KR, PH, AUS)
A-4734-601-A MIC BOARD, COMPLETE (TH)
A-4732-334-A DMB03 BOARD, COMPLETE (AEP, UK, RU)
A-4732-357-A DMB03 BOARD, COMPLETE (E2)
A-4732-362-A DMB03 BOARD, COMPLETE
(E3, E15, EA, MY, SP, TH, KR, PH)
A-4732-369-A DMB03 BOARD, COMPLETE (AUS)
1-775-190-11 WIRE (FLAT TYPE)(21 CORE)(TH)
1-827-402-11 WIRE (FLAT TYPE)(21 CORE)
(E2, E3, E15, EA, MY, SP, KR, PH)
1-827-403-11 WIRE (FLAT TYPE)(25 CORE)
(AEP, UK, RU, AUS)
Ref. No.
Part No.
Description
Remarks
55
56
57
57
58
3-970-608-01
1-827-003-11
1-775-073-11
1-827-404-11
1-791-112-11
SUMITITE (B3), +BV
CORD (WITH CONNECTOR) 19P
WIRE (FLAT TYPE)(7 CORE)(TH)
WIRE (FLAT TYPE)(7 CORE)(EXCEPT TH)
WIRE (FLAT TYPE)(11 CORE)
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
59
59
59
59
59
A-4732-199-A
A-4732-213-A
A-4732-319-A
A-4732-326-A
A-4732-329-A
MAIN BOARD, COMPLETE (AEP, UK)
MAIN BOARD, COMPLETE (E2)
MAIN BOARD, COMPLETE (MY, SP, KR, PH)
MAIN BOARD, COMPLETE (EA)
MAIN BOARD, COMPLETE (AUS)
59
59
59
60
A-4734-568-A
A-4734-597-A
A-4734-805-A
1-693-603-31
MAIN BOARD, COMPLETE (E3, E15)
MAIN BOARD, COMPLETE (TH)
MAIN BOARD, COMPLETE (RU)
TUNER
(FM/AM)(E2, E3, E15, EA, MY, SP, TH, PH, AUS)
71
HCD-WZ8D
Chassis Section (2/2)
not supplied
#1
61
#1
62
#1
63
60
59
#1
#2
#1
#1
56
#1
57
55
65
64
58
67
66
71
not supplied
#1
#3
68
53
54
69
not supplied
#1
#1
52
#1
70
51
not supplied
Ref. No.
Part No.
Description
Part No.
Description
60
60
60
61
61
1-693-604-11
1-693-605-11
1-693-627-11
1-769-938-11
1-773-002-11
TUNER (FM/AM)(AEP, UK)
TUNER (FM/AM)(KR)
TUNER (FM/AM)(RU)
WIRE (FLAT TYPE)(11 CORE)(EXCEPT AEP, UK)
WIRE (FLAT TYPE)(15 CORE)(AEP, UK)
65
65
66
66
67
A-4732-332-A
A-4734-603-A
1-792-108-11
1-827-401-11
A-4732-205-A
4CH-VOL BOARD, COMPLETE (AUS)
4CH-VOL BOARD, COMPLETE (TH)
WIRE (FLAT TYPE)(17 CORE)(TH)
WIRE (FLAT TYPE)(17 CORE)(EXCEPT TH)
VIDEO BOARD, COMPLETE (EXCEPT TH)
62
1-773-182-11 WIRE (FLAT TYPE)(23 CORE)
(EXCEPT AEP, UK, RU, AUS)
1-773-212-11 WIRE (FLAT TYPE)(25 CORE)
(AEP, UK, RU, AUS)
1-500-657-11 CORE, FERRIET
1-827-012-11 CORD (WITH CONNECTOR) 20P
A-4732-203-A 4CH-VOL BOARD, COMPLETE (AEP, UK, RU)
67
68
69
69
70
A-4734-606-A
1-787-056-11
A-4732-208-A
A-4734-612-A
1-687-208-11
VIDEO BOARD, COMPLETE (TH)
FAN, DC
REGULATOR BOARD, COMPLETE (EXCEPT TH)
REGULATOR BOARD, COMPLETE (TH)
HP AMP BOARD
71
#1
#2
#3
1-500-657-11
7-685-646-79
7-685-873-09
7-684-023-04
XXXXXXXXXX
SCREW +BVTP 3X8 TYPE2 N-S
SCREW +BVTT 3X10 (S)
N 3, TYPE 2
62
63
64
65
65
65
72
Remarks
A-4732-217-A 4CH-VOL BOARD, COMPLETE (E2)
A-4732-323-A 4CH-VOL BOARD, COMPLETE
(E3, E15, EA, MY, SP, KR, PH)
Ref. No.
Remarks
HCD-WZ8D
5-3. DVD Mechanism Section
404
403
402
407
405
406
408
409
M001
401
410
416
412
not supplid
414
410
414
411
410
415
414
413
Ref. No.
Part No.
Description
401
402
403
404
405
4-243-742-01
3-080-484-01
3-080-485-01
3-080-478-01
3-080-477-01
TRAY (AU)
DRIVING GEAR
PULLEY GEAR
BELT
CHUCK CAM
406
407
408
409
4-243-741-01
3-080-476-01
3-080-483-01
4-243-743-01
BASE (AU), LOADING
YOKE
CHUCK PLATE
HOLDER (DBU1)
Remarks
Ref. No.
Part No.
Description
410
411
0 412
413
414
3-053-847-31
1-689-264-11
1-477-263-11
A-4728-690-A
4-981-923-01
INSULATOR
PWB, FLEXIBLE
PICKUP UNIT (TDP022W)
RF BOARD, COMPLETE
SCREW (M), STEP
415
416
M001
Remarks
1-775-265-11 WIRE (FLAT TYPE)(29 CORE)(EXCEPT TH)
1-827-178-11 WIRE (FLAT TYPE)(5 CORE)
1-763-967-11 MOTOR, DC (LOADING)
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
73
HCD-WZ8D
SECTION 6
ELECTRICAL PARTS LIST
4CH-VOL
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they may
have some difference from the original one.
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
Ref. No.
Part No.
•
•
•
•
KR
MY
PH
RU
SP
TH
CAPACITORS:
uF: µF
COILS
uH: µH
SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
Abbreviation
AUS : Australian model
E2 : 120V AC area in E model
E3 : 240V AC area in E model
E15 : 220-240V AC area in E model
EA : Saudi Arabia model
Description
: Korean model
: Malaysia model
: Philippines model
: Russian model
: Singapore model
: Thai model
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Remarks
Ref. No.
A-4732-203-A 4CH-VOL BOARD, COMPLETE (AEP, UK, RU)
************************
A-4732-217-A 4CH-VOL BOARD, COMPLETE (E2)
************************
A-4732-323-A 4CH-VOL BOARD, COMPLETE
(E3, E15, EA, MY, SP, KR, PH)
************************
A-4732-332-A 4CH-VOL BOARD, COMPLETE (AUS)
************************
A-4734-603-A 4CH-VOL BOARD, COMPLETE (TH)
************************
C347
1-164-360-11 CERAMIC CHIP
0.1uF
C348
C351
1-164-360-11 CERAMIC CHIP
1-126-964-11 ELECT
0.1uF
10uF
C352
C353
C354
C355
C356
1-162-960-11
1-162-960-11
1-126-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
220PF
220PF
10uF
0.001uF
0.001uF
10%
10%
20.00%
10%
10%
50V
50V
50V
50V
50V
C357
C358
C359
C360
C361
1-126-964-11
1-162-964-11
1-162-966-11
1-126-964-11
1-126-964-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
10uF
0.001uF
0.0022uF
10uF
10uF
20.00%
10%
10%
20.00%
20.00%
50V
50V
50V
50V
50V
C362
C365
C366
C370
C371
1-126-964-11
1-126-964-11
1-162-995-11
1-126-964-11
1-126-964-11
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
10uF
10uF
0.022uF
10uF
10uF
20.00% 50V
20.00% 50V
50V
20.00% 50V
20.00% 50V
C372
C373
C374
C375
C376
1-126-964-11
1-126-964-11
1-126-964-11
1-126-964-11
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
10uF
10uF
10uF
10uF
20.00%
20.00%
20.00%
20.00%
20.00%
C377
1-126-964-11 ELECT
10uF
20.00% 50V
< CAPACITOR >
C301
C302
C303
C304
C305
1-126-964-11
1-162-960-11
1-162-960-11
1-126-964-11
1-162-964-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
10uF
220PF
220PF
10uF
0.001uF
20.00%
10%
10%
20.00%
10%
50V
50V
50V
50V
50V
C306
C307
C308
C309
C310
1-162-964-11
1-126-964-11
1-162-964-11
1-162-966-11
1-126-964-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.001uF
10uF
0.001uF
0.0022uF
10uF
10%
20.00%
10%
10%
20.00%
50V
50V
50V
50V
50V
C311
C312
C315
C316
C320
1-126-964-11
1-126-964-11
1-126-964-11
1-162-995-11
1-126-964-11
ELECT
ELECT
ELECT
CERAMIC CHIP
ELECT
10uF
10uF
10uF
0.022uF
10uF
20.00% 50V
20.00% 50V
20.00% 50V
50V
20.00% 50V
C321
C322
C323
C324
C325
1-162-964-11
1-126-964-11
1-162-964-11
1-126-964-11
1-126-964-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
0.001uF
10uF
0.001uF
10uF
10uF
10%
20.00%
10%
20.00%
20.00%
50V
50V
50V
50V
50V
C330
C331
C332
C333
C334
1-165-176-11
1-126-964-11
1-136-169-00
1-136-165-00
1-126-964-11
CERAMIC CHIP
ELECT
FILM
FILM
ELECT
0.047uF
10uF
0.22uF
0.1uF
10uF
10.00%
20.00%
5.00%
5.00%
20.00%
16V
50V
50V
50V
50V
C337
C341
C342
C343
C344
1-164-360-11
1-126-933-11
1-164-360-11
1-126-960-11
1-126-933-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
0.1uF
100uF
0.1uF
1uF
100uF
16V
20.00% 16V
16V
20.00% 50V
20.00% 16V
C345
C346
1-126-935-11 ELECT
1-164-360-11 CERAMIC CHIP
470uF
0.1uF
Part No.
Description
Remarks
16V
(AEP, UK, RU, AUS)
16V
20.00% 50V
50V
50V
50V
50V
50V
< CONNECTOR >
74
20.00% 16V
16V
(AEP, UK, RU, AUS)
CN301
CN301
* CN302
CN303
CN303
1-784-786-11 CONNECTOR, FFC 25P (AEP, UK, RU, AUS)
1-784-784-11 CONNECTOR, FFC 23P
(EXCEPT AEP, UK, RU, AUS)
1-566-460-11 PIN, CONNECTOR 4P
1-779-293-11 CONNECTOR, FFC (LIF (NON-ZIF)) 25P
(AEP, UK, RU, AUS)
1-779-289-11 CONNECTOR, FFC (LIF (NON-ZIF)) 21P
(EXCEPT AEP, UK, RU, AUS)
< IC >
IC301
6-703-651-11 IC M61530FP-D60G
< JACK >
J302
1-770-377-31 JACK, PIN 1P 9 (SUB WOOFER OUT)
< COIL >
L341
1-412-064-11 INDUCTOR
100uH
HCD-WZ8D
4CH-VOL
Ref. No.
Part No.
Description
Remarks
< TRANSISTOR >
Q301
Q302
Q303
Q304
Q305
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
Q306
Q307
Q308
Q309
8-729-141-73
8-729-141-73
8-729-141-73
8-729-141-73
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
< RESISTOR >
R301
R302
R303
R304
R305
1-216-841-11
1-216-817-11
1-216-833-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
470
10K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R306
R307
R308
R309
R310
1-216-829-11
1-216-841-11
1-216-841-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47K
47K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R311
R312
R313
1-216-841-11 METAL CHIP
1-216-857-11 METAL CHIP
1-216-833-11 METAL CHIP
47K
1M
10K
5%
5%
5%
R320
R321
1-216-833-11 METAL CHIP
1-216-821-11 METAL CHIP
10K
1K
1/10W
1/10W
1/10W
(EXCEPT TH)
5%
1/10W
5%
1/10W
R322
R323
R330
R331
R332
1-216-829-11
1-216-841-11
1-216-857-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47K
1M
1K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R333
R334
R335
R336
R337
1-216-825-11
1-216-845-11
1-216-821-11
1-216-821-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
100K
1K
1K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R340
R341
R342
R351
R352
1-216-864-11
1-216-821-11
1-216-821-11
1-216-841-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
1K
1K
47K
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R353
R354
R355
R356
R357
1-216-833-11
1-216-833-11
1-216-821-11
1-216-829-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
1K
4.7K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R358
R359
R360
R361
R362
1-216-841-11
1-216-825-11
1-216-825-11
1-216-841-11
1-216-857-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
2.2K
2.2K
47K
1M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R363
R370
R371
R372
R373
1-216-833-11
1-216-825-11
1-216-845-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
2.2K
100K
1K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Ref. No.
BACK LIGHT
Part No.
Description
R374
R375
R376
R377
R378
1-216-845-11
1-216-821-11
1-216-825-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
1K
2.2K
100K
1K
5%
5%
5%
5%
5%
Remarks
1/10W
1/10W
1/10W
1/10W
1/10W
R379
R380
R381
R382
R383
1-216-825-11
1-216-845-11
1-216-821-11
1-216-825-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
100K
1K
2.2K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R384
R385
R386
R387
R388
1-216-821-11
1-216-825-11
1-216-845-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
2.2K
100K
1K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R389
1-216-845-11 METAL CHIP
100K
5%
1/10W
R390
1-216-821-11 METAL CHIP
1K
5%
1/10W
R391
1-216-825-11 METAL CHIP
2.2K
5%
1/10W
R392
1-216-845-11 METAL CHIP
100K
5%
1/10W
R393
1-216-821-11 METAL CHIP
1K
5%
1/10W
************************************************************
1-687-204-11 BACK LIGHT BOARD
*****************
< CAPACITOR >
C608
C611
C622
C623
1-162-971-11
1-162-971-11
1-162-971-11
1-162-971-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
10.00%
10.00%
10.00%
10.00%
50V
50V
50V
50V
< CONNECTOR >
CN602
1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4P
< DIODE >
D608
D609
D610
D611
D612
6-500-664-01
6-500-665-01
6-500-665-01
6-500-663-01
6-500-663-01
DIODE SELS6E14C-MTP5 (LCD BACK LIGHT)
DIODE SELU6614C-STP5 (LCD BACK LIGHT)
DIODE SELU6614C-STP5 (LCD BACK LIGHT)
DIODE SELS6D14C-TP5 (LCD BACK LIGHT)
DIODE SELS6D14C-TP5 (LCD BACK LIGHT)
D613
6-500-664-01 DIODE SELS6E14C-MTP5
< RESISTOR >
R608
R609
R610
R611
R633
1-216-820-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
820
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R634
R635
R636
R667
R668
1-216-820-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-820-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
820
1K
1K
1K
820
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R669
R670
R691
R692
R693
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
75
HCD-WZ8D
BACK LIGHT
Ref. No.
Part No.
CD-TC SW
DMB03
Description
Remarks
R694
1-216-820-11 METAL CHIP
820
5%
1/10W
R695
1-216-820-11 METAL CHIP
820
5%
1/10W
R696
1-216-820-11 METAL CHIP
820
5%
1/10W
************************************************************
1-687-207-11 CD-TC SW BOARD
************
R651
R652
R653
1-216-837-11 METAL CHIP
1-216-839-11 METAL CHIP
1-216-843-11 METAL CHIP
22K
33K
68K
5%
5%
5%
1/10W
1/10W
1/10W
< SWITCH >
S638
1-762-875-21 SWITCH, KEYBOARD (Z)
S639
1-762-875-21 SWITCH, KEYBOARD (CD SYNC)
S640
1-762-875-21 SWITCH, KEYBOARD (z START)
************************************************************
A-4732-334-A DMB03 BOARD, COMPLETE (AEP, UK, RU)
**********************
A-4732-357-A DMB03 BOARD, COMPLETE (E2)
**********************
A-4732-362-A DMB03 BOARD, COMPLETE
(E3, E15, EA, MY, SP, TH, KR, PH)
**********************
A-4732-369-A DMB03 BOARD, COMPLETE (AUS)
**********************
< CAPACITOR >
C101
C151
C204
C205
C213
1-126-246-11
1-126-206-11
1-164-947-11
1-164-947-11
1-126-209-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
220uF
100uF
0.01uF
0.01uF
100uF
C214
C215
C216
C218
C220
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
50V
50V
50V
50V
50V
C226
C227
C229
C230
C231
1-107-820-11
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.01uF
0.01uF
0.01uF
16V
50V
50V
50V
50V
C232
C233
C234
C235
C236
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
50V
50V
50V
50V
50V
C237
C238
C239
C240
C241
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
50V
50V
50V
50V
50V
C242
C243
C244
C245
C246
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
50V
50V
50V
50V
50V
C247
C248
1-164-947-11 CERAMIC CHIP
1-164-947-11 CERAMIC CHIP
0.01uF
0.01uF
50V
50V
76
20%
20%
4V
6.3V
50V
50V
20.00% 4V
Ref. No.
Part No.
Description
Remarks
C249
C250
C251
1-164-947-11 CERAMIC CHIP
1-164-947-11 CERAMIC CHIP
1-164-947-11 CERAMIC CHIP
0.01uF
0.01uF
0.01uF
50V
50V
50V
C252
C253
C254
C255
C256
1-164-947-11
1-164-947-11
1-164-947-11
1-117-370-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
10uF
0.01uF
50V
50V
50V
10V
50V
C257
C258
C259
C260
C261
1-164-947-11
1-117-370-11
1-164-947-11
1-164-947-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10uF
0.01uF
0.01uF
0.01uF
50V
10V
50V
50V
50V
C262
C263
C264
C265
C266
1-164-947-11
1-164-947-11
1-164-947-11
1-117-370-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
10uF
0.01uF
50V
50V
50V
10V
50V
C267
C268
C269
C270
C271
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
50V
50V
50V
50V
50V
C272
C275
C281
C282
C283
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
50V
50V
50V
50V
50V
C284
C286
C287
C289
1-164-947-11
1-164-947-11
1-164-947-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
C302
1-164-943-11 CERAMIC CHIP
0.01uF
C303
C304
C305
C306
C307
1-164-943-11
1-164-943-11
1-164-943-11
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
10.00%
10.00%
10.00%
10.00%
10.00%
C308
C309
C315
C316
C321
1-164-874-11
1-164-874-11
1-164-947-11
1-164-947-11
1-126-206-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
100PF
100PF
0.01uF
0.01uF
100uF
5.00% 50V
5.00% 50V
50V
50V
20%
6.3V
C322
C323
C324
C325
C326
1-107-820-11
1-107-820-11
1-107-820-11
1-126-209-11
1-164-947-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
100uF
0.01uF
16V
16V
16V
20.00% 4V
50V
C352
C355
C356
C357
C363
1-126-206-11
1-126-206-11
1-126-193-11
1-126-193-11
1-107-820-11
ELECT CHIP
ELECT CHIP
ELECT
ELECT
CERAMIC CHIP
100uF
100uF
1uF
1uF
0.1uF
20%
20%
20%
20%
C364
C365
C366
C367
1-126-206-11
1-107-820-11
1-126-206-11
1-164-935-11
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
100uF
0.1uF
100uF
470PF
20%
50V
50V
50V
50V
(AEP, UK, RU, AUS)
10.00% 16V
16V
16V
16V
16V
16V
6.3V
6.3V
50V
50V
16V
6.3V
16V
20%
6.3V
10.00% 50V
HCD-WZ8D
DMB03
Ref. No.
Part No.
Description
C368
1-164-935-11 CERAMIC CHIP
C392
C393
C394
C395
1-126-395-11
1-164-947-11
1-126-246-11
1-107-820-11
C396
C397
Remarks
470PF
10.00% 50V
ELECT
22uF
20%
16V
CERAMIC CHIP 0.01uF
50V
ELECT CHIP
220uF
20%
4V
CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
Ref. No.
Part No.
Description
Remarks
C573
1-164-874-11 CERAMIC CHIP
100PF
5.00% 50V
C588
C589
C590
C592
C601
1-164-939-11
1-164-939-11
1-164-939-11
1-124-779-00
1-107-820-11
C603
1-117-370-11 CERAMIC CHIP 10uF
10V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
CERAMIC CHIP 0.0022uF 10.00% 50V
CERAMIC CHIP 0.0022uF 10.00% 50V
CERAMIC CHIP 0.0022uF 10.00% 50V
ELECT CHIP
10uF
20%
16V
CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
C412
C413
C414
C415
1-126-246-11 ELECT CHIP
220uF
20%
4V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
1-216-864-11 METAL CHIP
0
5%
1/10W
1-216-864-11 METAL CHIP
0
5%
1/10W
1-216-864-11 METAL CHIP
0
5%
1/10W
C416
C501
C502
C503
C504
1-216-864-11
1-164-943-11
1-164-943-11
1-127-772-81
1-127-772-81
METAL CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0
0.01uF
0.01uF
33000PF
33000PF
5%
10.00%
10.00%
10%
10%
1/10W
16V
16V
10V
10V
C506
C508
C509
C510
C512
1-164-934-11
1-164-937-11
1-164-934-11
1-164-937-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
330PF
0.001uF
330PF
0.001uF
0.01uF
10.00%
10.00%
10.00%
10.00%
10.00%
50V
50V
50V
50V
16V
C514
C516
C517
C518
C519
1-164-943-11
1-164-939-11
1-117-370-11
1-164-947-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10.00% 16V
0.0022uF 10.00% 50V
10uF
10V
0.01uF
50V
0.01uF
10.00% 16V
C522
C525
C526
C527
C528
1-125-777-11
1-164-947-11
1-126-395-11
1-164-947-11
1-126-395-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0.1uF
0.01uF
22uF
0.01uF
22uF
10.00% 6.3V
50V
20%
16V
50V
20%
16V
C529
C531
C533
C534
C535
1-164-947-11
1-119-923-11
1-164-939-11
1-107-819-11
1-164-939-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.047uF
0.0022uF
0.022uF
0.0022uF
10.00%
10.00%
10.00%
10.00%
C543
C544
C545
C547
C548
1-107-820-11
1-125-777-11
1-117-370-11
1-107-725-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
10uF
0.1uF
0.01uF
16V
10.00% 10V
10V
10.00% 16V
10.00% 16V
C551
C552
C553
C556
C558
1-125-891-11
1-216-295-91
1-164-940-11
1-117-370-11
1-126-209-11
CERAMIC CHIP
SHORT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.47uF
10.00% 10V
0
0.0033uF 10.00% 16V
10uF
10V
100uF
20.00% 4V
C701
C702
C703
C705
C706
1-126-209-11
1-117-370-11
1-125-777-11
1-164-943-11
1-125-777-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
10uF
0.1uF
0.01uF
0.1uF
20.00% 4V
10V
10.00% 6.3V
10.00% 16V
10.00% 10V
C559
C560
C561
C563
C565
1-125-777-11
1-164-938-11
1-107-820-11
1-164-874-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.0015uF
0.1uF
100PF
0.1uF
10.00% 10V
10.00% 50V
16V
5.00% 50V
10.00% 10V
C708
C709
C711
C712
C713
1-164-943-11
1-125-777-11
1-164-923-11
1-164-874-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.047uF
100PF
0.1uF
10.00%
10.00%
10.00%
5.00%
10.00%
C567
C568
C569
C570
1-107-820-11
1-117-370-11
1-107-820-11
1-117-370-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
0.1uF
10uF
16V
10V
16V
10V
C714
C715
C716
C718
1-125-777-11
1-164-938-11
1-125-891-11
1-107-820-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10.00% 10V
0.0015uF 10.00% 50V
0.47uF
10.00% 10V
0.1uF
16V
C605
C606
C607
C608
C609
C610
C611
C612
C613
50V
10V
50V
16V
50V
C614
C615
C616
C617
C618
C619
C626
C627
C650
C651
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-164-868-11 CERAMIC CHIP 56PF
5.00% 50V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-164-858-11 CERAMIC CHIP 22PF
5.00% 50V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-107-820-11 CERAMIC CHIP 0.1uF
16V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-117-370-11 CERAMIC CHIP 10uF
10V
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
16V
10V
10V
50V
10V
77
HCD-WZ8D
DMB03
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
C918
C924
C925
C926
1-164-947-11
1-164-947-11
1-126-395-11
1-126-246-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT CHIP
0.01uF
0.01uF
22uF
220uF
C927
C1302
C1304
1-164-947-11 CERAMIC CHIP
1-107-820-11 CERAMIC CHIP
1-218-990-11 SHORT CHIP
0.01uF
0.1uF
0
C720
1-125-777-11 CERAMIC CHIP
0.1uF
10.00% 10V
C721
C722
C723
C724
C725
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
16V
16V
16V
16V
16V
C726
C727
C728
C729
C730
1-107-820-11
1-117-370-11
1-125-777-11
1-117-370-11
1-107-820-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
0.1uF
10uF
0.1uF
16V
10V
10.00% 10V
10V
16V
C740
C741
C742
C743
C744
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
1-107-820-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
16V
16V
16V
16V
16V
C745
C752
C760
C761
C762
1-107-820-11
1-125-777-11
1-107-820-11
1-107-820-11
1-107-820-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
16V
10.00% 10V
16V
16V
16V
C763
C764
C765
C766
C767
1-107-820-11
1-107-820-11
1-125-777-11
1-164-874-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
100PF
0.1uF
16V
16V
10.00% 10V
5.00% 50V
10.00% 10V
C768
C769
C770
C771
C772
1-125-777-11
1-125-777-11
1-107-820-11
1-119-923-11
1-107-820-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.047uF
0.1uF
10.00% 10V
10.00% 10V
16V
10.00% 10V
16V
C773
C774
C775
C776
C777
1-125-891-11
1-164-941-11
1-107-820-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47uF
0.0047uF
0.1uF
0.1uF
0.1uF
10.00% 10V
10.00% 16V
16V
10.00% 10V
10.00% 10V
C778
C779
C780
C781
C782
1-107-820-11
1-117-370-11
1-117-370-11
1-165-643-21
1-164-938-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
10uF
10uF
150uF
20%
0.0015uF 10.00%
C783
C901
C902
C903
C904
1-164-938-11
1-126-209-11
1-164-947-11
1-126-209-11
1-164-947-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.0015uF 10.00% 50V
100uF
20.00% 4V
0.01uF
50V
100uF
20.00% 4V
0.01uF
50V
C905
C906
C907
C908
C909
1-164-947-11
1-164-947-11
1-164-947-11
1-164-874-11
1-164-874-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
100PF
100PF
50V
50V
50V
5.00% 50V
5.00% 50V
FL203
FL204
FL205
FL206
FL302
1-234-177-21
1-234-177-21
1-234-177-21
1-234-177-21
1-234-177-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
C910
C913
C914
C915
C916
1-164-947-11
1-127-772-81
1-164-849-11
1-164-846-11
1-126-209-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.01uF
33000PF
9PF
6PF
100uF
10%
0.50PF
0.50PF
20.00%
50V
10V
50V
50V
4V
FL303
FL352
FL501
FL502
FL601
1-234-177-21
1-234-177-21
1-234-177-21
1-234-177-21
1-234-177-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
C917
1-164-947-11 CERAMIC CHIP
16V
10V
10V
4V
50V
Remarks
20%
20%
50V
50V
16V
4V
50V
16V
< CONNECTOR >
CN101
CN102
CN103
CN105
CN107
CN107
CN202
CN202
CN501
CN901
1-784-366-21 CONNECTOR, FFC/FPC 7P
1-815-954-21 PIN, CONNECTOR (PC BOARD) 13P
1-784-370-21 CONNECTOR, FFC/FPC 11P
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-784-376-11 CONNECTOR, FFC/FPC 17P
1-784-382-21 CONNECTOR, FFC/FPC 25P (AEP, UK, RU, AUS)
1-778-692-11 CONNECTOR, FFC/FPC 21P
(E2, E3, E15, EA, MY, SP, TH, KR, PH)
1-784-364-21 CONNECTOR, FFC/FPC 4P
(AEP, UK, RU, E2, E3, E15, EA, MY, SP, KR, PH)
1-784-364-31 CONNECTOR, FFC/FPC 4P (AUS)
1-778-957-11 CONNECTOR, FFC/FPC 29P
1-764-177-11 PIN, CONNECTOR (SMD)(1.5mm) 7P
< DIODE >
D202
D392
D393
D394
D901
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
D1101
D1102
D1201
D1202
D1203
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
D1204
D1301
D1302
D1303
D1304
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
D1801
D1802
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
< FERRITE BEAD >
78
0.01uF
50V
FB902
FB903
1-500-284-21 FERRITE
1-500-284-21 FERRITE
0uH
0uH
< FILTER >
0uH
0uH
0uH
0uH
0uH
0uH
0uH
0uH
0uH
0uH
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
HCD-WZ8D
DMB03
Ref. No.
Part No.
Description
Remarks
FL602
1-234-177-21 FERRITE
FL701
FL702
FL703
FL704
1-234-177-21
1-234-177-21
1-234-177-21
1-234-177-21
0uH
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
FERRITE
0uH
FERRITE
0uH
FERRITE
0uH
FERRITE
0uH
FL705
FL706
FL901
FL903
FL908
1-234-177-21
1-234-177-21
1-234-177-21
1-234-177-21
1-234-177-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
0uH
< IC >
IC203
* IC204
IC206
IC207
IC211
6-705-034-01
6-703-671-01
6-803-555-01
6-703-540-01
6-700-398-01
IC HY57V283220T-6
IC BR9040F-WE2
IC MBM29DL324BE-90PFTN-SB3V107
IC ZIVA5X-C1F
IC uPC2918T-E1
IC216
IC252
IC255
IC256
IC258
6-700-437-01
8-759-680-48
8-759-058-54
8-759-549-21
8-759-549-21
IC SN74ALVCH16841DGGR
IC TC7WH157FK (TE85R)(AEP, UK, RU, AUS)
IC TC7S00FU (TE85R)
IC SN74LV573APWR
IC SN74LV573APWR
IC259
IC302
IC352
IC392
IC393
8-759-549-21
6-703-787-01
8-759-560-56
8-759-583-47
6-700-394-01
IC SN74LV573APWR
IC PCM1609KPTR
IC PCM1800E/2K
IC uPC2933T-E2
IC BA25BC0FP-E2
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
IC501
IC503
IC509
IC601
6-702-157-01
8-759-058-43
8-752-408-73
6-704-421-01
Ref. No.
JW804
JW805
JW806
Part No.
Description
1-218-990-11 SHORT CHIP
1-218-990-11 SHORT CHIP
1-218-990-11 SHORT CHIP
Remarks
0
0
0
< COIL >
L402
L403
L404
L405
L406
1-216-296-11
1-216-296-11
1-216-296-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
L412
L413
L414
L415
L416
1-216-296-11
1-216-296-11
1-216-296-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
L901
1-412-031-11 INDUCTOR CHIP 47uH
< TRANSISTOR >
IC602
IC FAN8035L
IC NJM3404AV (TE2)
IC CXD3068Q
IC CXD9782R
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
8-759-538-16 IC IS61LV6416-10TT (ISSI)
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
IC701
IC701
IC703
IC706
IC901
6-703-552-01
6-703-552-01
8-759-058-43
8-759-564-30
8-752-937-54
IC CXD1882R
IC CXD1882R (AEP)
IC NJM3404AV (TE2)
IC MSM51V18165F-60TSKR1
IC CXP973064-228R
IC902
IC903
IC904
IC906
IC907
8-759-058-64
8-759-641-86
6-702-563-01
6-700-407-01
8-759-583-47
IC TC7S32FU-TE85L
IC BR24C16F-E2
IC TC7W74FK-TE85L
IC SM8707GV-G-E2
IC uPC2933T-E2
< JUMPER RESISTOR >
JW392
JW601
JW602
JW603
JW604
1-216-864-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
5%
1/10W
0 (AEP, UK, RU, E2)
0 (AEP, UK, RU, E2)
0 (AEP, UK, RU, E2)
0 (AEP, UK, RU, E2)
JW605
JW606
JW607
JW801
JW802
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0 (AEP, UK, RU, E2)
0 (AEP, UK, RU, E2)
0 (AEP, UK, RU, E2)
0
0
JW803
1-218-990-11 SHORT CHIP
0
Q202
Q901
Q903
Q904
8-729-929-26
8-729-929-26
8-729-025-28
8-729-025-28
TRANSISTOR DTC114TE-TL
TRANSISTOR DTC114TE-TL
TRANSISTOR 2SK1828TE85L
TRANSISTOR 2SK1828TE85L
< RESISTOR >
R10
R11
R12
R13
R14
1-216-801-11
1-216-801-11
1-216-801-11
1-216-801-11
1-216-801-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
22
22
22
22
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R15
R197
R198
R207
R213
1-216-801-11
1-216-829-11
1-216-829-11
1-216-864-11
1-216-807-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
4.7K
4.7K
0
68
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R214
R215
R217
R218
R219
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R220
R221
R222
R223
R224
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R225
R226
R227
R228
R230
1-216-864-11
1-216-864-11
1-216-829-11
1-216-864-11
1-216-803-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
4.7K
0
33
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R231
R232
R233
R234
R239
1-216-803-11
1-216-803-11
1-216-864-11
1-216-833-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33
33
0
10K
100
R240
R241
R243
1-216-841-11 METAL CHIP
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
47K
0
0
5%
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
(AEP, UK, RU, AUS)
5%
5%
5%
1/10W
1/10W
1/10W
79
HCD-WZ8D
DMB03
Ref. No.
Part No.
Description
Remarks
R244
R245
1-216-821-11 METAL CHIP
1-216-829-11 METAL CHIP
1K
4.7K
5%
5%
1/10W
1/10W
R246
R247
R248
R250
R251
1-216-833-11
1-216-821-11
1-216-829-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
4.7K
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R253
R254
R255
R257
R259
1-216-829-11
1-216-829-11
1-216-864-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
0
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R260
R261
R262
R263
R264
1-216-829-11
1-216-829-11
1-216-864-11
1-218-285-11
1-218-285-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
0
75
75
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R265
R266
R267
R268
R269
1-218-285-11
1-218-285-11
1-218-285-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
75
75
75
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R270
R273
R274
R275
R276
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R277
R278
R279
R280
R281
1-216-864-11
1-218-285-11
1-218-285-11
1-218-285-11
1-218-285-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
75
75
75
75
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R282
R283
R284
R285
R288
1-218-285-11
1-218-847-11
1-218-829-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
75
1K
180
0
0
R291
R292
R293
R294
R295
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R296
R301
R302
R303
R304
1-216-864-11
1-216-821-11
1-216-813-11
1-216-813-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
1K
220
220
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R305
R306
R307
R308
R309
1-216-813-11
1-216-813-11
1-216-813-11
1-216-813-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
220
220
220
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R310
R311
R312
R313
R314
1-216-809-11
1-216-809-11
1-216-809-11
1-216-833-11
1-216-801-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
10K
22
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
80
5%
1/10W
0.5% 1/10W
0.5% 1/10W
5%
1/10W
5%
1/10W
(AEP, UK, RU, AUS)
Ref. No.
Part No.
Description
R327
R328
R329
R335
R352
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-821-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
1K
5%
5%
5%
5%
5%
Remarks
1/10W
1/10W
1/10W
1/10W
1/10W
R353
R362
R392
R501
R502
1-216-821-91
1-216-833-11
1-216-797-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
10
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R503
R504
R505
R506
R507
1-216-841-11
1-216-841-11
1-216-841-11
1-216-841-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
47K
47K
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R508
R510
R511
R512
R513
1-216-864-11
1-216-847-11
1-216-847-11
1-216-842-11
1-216-842-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
150K
150K
56K
56K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R516
R517
R519
R520
R521
1-216-829-11
1-216-825-11
1-216-845-11
1-216-833-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
2.2K
100K
10K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R522
R523
R524
R525
R527
1-216-829-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
10K
10K
10K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R528
R529
R530
R531
R532
1-216-864-11
1-216-839-11
1-216-842-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
33K
56K
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R533
R534
R535
R536
R537
1-216-839-11
1-216-842-11
1-216-864-11
1-216-833-11
1-216-843-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
56K
0
10K
68K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R538
R539
R540
R541
R543
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R544
R545
R547
R548
R550
1-216-864-11
1-216-833-11
1-216-864-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
10K
0
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R551
R552
R553
R554
R555
1-216-821-11
1-216-821-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R558
R559
R560
1-216-841-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
47K
1K
1K
5%
5%
5%
1/10W
1/10W
1/10W
HCD-WZ8D
DMB03
Ref. No.
Part No.
Description
Remarks
R561
R562
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
1K
5%
5%
1/10W
1/10W
R563
R564
R565
R566
R567
1-216-821-11
1-216-821-11
1-216-821-11
1-216-833-11
1-216-827-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
10K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R568
R569
R571
R572
R573
1-216-857-11
1-216-864-11
1-216-857-11
1-216-853-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
0
1M
470K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R574
1-216-815-11 METAL CHIP
330
R575
R576
R577
R578
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
R579
R580
R581
R583
R584
1-216-832-11
1-216-839-11
1-216-834-11
1-216-864-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
8.2K
33K
12K
0
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R585
R586
R587
R588
R589
1-216-864-11
1-218-747-11
1-216-864-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
200K
0
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R592
R593
R597
1-216-864-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-864-11 METAL CHIP
0
100K
0
5%
5%
5%
R599
R601
1-216-821-11 METAL CHIP
1-216-864-11 METAL CHIP
1K
0
5%
5%
1/10W
1/10W
1/10W
(AEP)
1/10W
1/10W
R602
1-216-821-11 METAL CHIP
1K
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
Ref. No.
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-857-11 METAL CHIP
1M
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
R618
R620
R621
R622
R623
R624
R626
R627
R628
R629
R630
R631
R604
R605
R606
R607
R608
R609
R610
R611
R612
R613
R614
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
Remarks
R617
R625
R603
Description
1-216-864-11 METAL CHIP
0
5%
1/10W
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
R619
5%
1/10W
(AEP, UK, RU, AUS)
5%
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
Part No.
R615
R616
R633
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
R694
R695
R696
R698
1-216-864-11 METAL CHIP
0
5%
1/10W
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
1-216-833-11 METAL CHIP
10K
5%
1/10W
1-216-864-11 METAL CHIP
0
5%
1/10W
1-216-864-11 METAL CHIP
0
5%
1/10W
1-216-864-11 METAL CHIP
0
5%
1/10W
R699
R700
R707
R708
R709
1-216-864-11
1-216-832-11
1-216-809-11
1-216-853-11
1-216-847-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
8.2K
100
470K
150K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R710
R711
R712
R713
R714
1-216-833-11
1-216-825-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
2.2K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R715
R716
R717
R718
R719
1-216-833-11
1-216-809-11
1-216-845-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
100K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R720
R721
R724
R725
R726
1-216-821-11
1-216-839-11
1-216-821-11
1-216-824-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
33K
1K
1.8K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R727
R728
1-216-827-11 METAL CHIP
1-216-833-11 METAL CHIP
3.3K
10K
5%
5%
1/10W
1/10W
81
HCD-WZ8D
DMB03
Ref. No.
Part No.
Description
Remarks
R730
R731
R732
1-216-801-11 METAL CHIP
1-216-801-11 METAL CHIP
1-216-833-11 METAL CHIP
22
22
10K
5%
5%
5%
1/10W
1/10W
1/10W
R733
R734
R735
R736
R737
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R738
R741
R742
R743
R744
1-216-833-11
1-216-801-11
1-216-801-11
1-216-801-11
1-216-801-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
22
22
22
22
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R745
R746
R747
R748
R750
1-216-841-11
1-216-841-11
1-216-839-11
1-216-839-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
33K
33K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R751
R752
R753
R754
R755
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R756
R757
R758
R759
R762
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R763
R764
R765
R766
R767
1-216-832-11
1-216-857-11
1-216-837-11
1-216-864-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
8.2K
1M
22K
0
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R769
R770
R776
R777
R778
1-216-825-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
0
0
0
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R780
R781
R784
R785
R786
1-216-864-11
1-216-864-11
1-216-864-11
1-216-833-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
10K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R787
R788
R789
R799
R805
1-216-845-11
1-216-845-11
1-216-845-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R901
R902
R904
R905
R906
1-216-801-11
1-216-801-11
1-216-833-11
1-216-801-11
1-216-801-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
22
10K
22
22
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R907
R908
R910
R911
R912
1-216-801-11
1-216-833-11
1-216-864-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
10K
0
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
82
Ref. No.
Part No.
Description
R913
R915
R916
R917
R918
1-216-833-11
1-216-809-11
1-216-821-11
1-216-821-11
1-216-801-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
1K
1K
22
5%
5%
5%
5%
5%
Remarks
1/10W
1/10W
1/10W
1/10W
1/10W
R919
R920
R921
R922
R923
1-216-864-11
1-216-809-11
1-216-809-11
1-216-801-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100
100
22
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R925
R926
R927
R928
R929
1-216-809-11
1-216-809-11
1-216-857-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
1M
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R930
R931
R932
R933
R935
1-216-809-11
1-216-801-11
1-216-801-11
1-216-801-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
22
22
22
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R940
R942
R943
R947
R948
1-216-809-11
1-216-809-11
1-216-809-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R949
R958
R962
R964
R970
1-216-864-11
1-216-801-11
1-216-833-11
1-216-833-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
22
10K
10K
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R971
R973
R974
R975
R976
1-216-864-11
1-216-864-11
1-216-864-11
1-216-833-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
10K
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R978
R984
R988
R990
R991
1-216-833-11
1-216-833-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R992
R994
R995
R996
R997
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R998
R1000
R1001
1-216-864-11 METAL CHIP
1-216-829-11 METAL CHIP
1-216-864-11 METAL CHIP
0
4.7K
0
R1101
R1201
1-164-156-11 CERAMIC CHIP
1-216-864-11 METAL CHIP
0.1uF
0
R1202
R1301
R1302
R1303
R1304
1-164-156-11
1-164-156-11
1-216-864-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
METAL CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0
0.1uF
0.1uF
R1801
1-164-156-11 CERAMIC CHIP
0.1uF
5%
1/10W
5%
1/10W
5%
1/10W
(AEP, UK, RU, AUS)
25V
5%
1/10W
5%
25V
25V
1/10W
25V
25V
25V
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
HCD-WZ8D
DMB03
Ref. No.
Part No.
Description
R1803
R9980
R9981
R9982
1-164-156-11
1-216-864-11
1-216-864-11
1-216-864-11
CERAMIC CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0.1uF
0
0
0
5%
5%
5%
25V
1/10W
1/10W
1/10W
Remarks
R9983
R9984
R9985
R9986
R9987
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R9988
R9993
R9994
R9998
R9999
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
ENTER-SW
Ref. No.
Part No.
HP AMP
LCD
MAIN
Description
Remarks
< JACK >
J603
1-793-829-11 JACK, HEADPHONE (i)
************************************************************
A-4732-447-A LCD BOARD, COMPLETE (EXCEPT TH)
********************
A-4734-602-A LCD BOARD, COMPLETE (TH)
********************
< CAPACITOR >
C246
C247
C248
C249
C250
1-164-156-11
1-164-156-11
1-164-156-11
1-164-156-11
1-126-160-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
0.1uF
0.1uF
0.1uF
1uF
C251
C252
C261
C262
C263
1-126-160-11
1-164-156-11
1-162-953-11
1-162-953-11
1-162-953-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
100PF
100PF
100PF
C264
C265
C266
C267
1-162-953-11
1-162-953-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
0.1uF
0.1uF
20%
25V
25V
25V
25V
50V
< COMPOSITION CIRCUIT BLOCK >
RB10
RB11
RB12
RB13
RB14
1-233-388-11
1-233-388-11
1-233-388-11
1-233-388-11
1-233-388-11
RES, NETWORK 68 (3216)
RES, NETWORK 68 (3216)
RES, NETWORK 68 (3216)
RES, NETWORK 68 (3216)
RES, NETWORK 68 (3216)
RB15
RB16
RB17
RB18
RB19
1-233-388-11
1-233-388-11
1-233-388-11
1-234-524-21
1-234-524-21
RES, NETWORK 68 (3216)
RES, NETWORK 68 (3216)
RES, NETWORK 68 (3216)
RES, CHIP NETWORK 33
RES, CHIP NETWORK 33
RB20
RB21
1-234-524-21 RES, CHIP NETWORK 33
1-234-524-21 RES, CHIP NETWORK 33
20%
5%
5%
5%
50V
25V
50V
50V
50V
5%
5%
50V
50V
25V
25V
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< DIODE >
D261
D262
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
< VIBRATOR >
< RESISTOR >
X601
1-795-126-21 VIBRATOR, CRYSTAL (12.288MHz)
(E3, E15, EA, MY, SP, TH, KR, PH, AUS)
X901
1-781-945-21 VIBRATOR, CERAMIC (20MHz)
X902
1-795-630-11 VIBRATOR, CRYSTAL (27MHz)
************************************************************
1-687-205-11 ENTER-SW BOARD
****************
R252
R253
R254
R255
R256
1-216-833-11
1-216-833-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
100
100
100
R257
1-216-809-11 METAL CHIP
100
5%
1/10W
R258
1-216-809-11 METAL CHIP
100
5%
1/10W
************************************************************
< RESISTOR >
R646
R647
R648
R649
R650
1-216-827-11
1-216-829-11
1-218-867-11
1-216-833-11
1-216-835-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
4.7K
6.8K
10K
15K
5%
5%
5%
5%
5%
A-4732-199-A MAIN BOARD, COMPLETE (AEP, UK)
*********************
A-4732-213-A MAIN BOARD, COMPLETE (E2)
*********************
A-4732-319-A MAIN BOARD, COMPLETE (MY, SP, KR, PH)
*********************
A-4732-326-A MAIN BOARD, COMPLETE (EA)
*********************
A-4732-329-A MAIN BOARD, COMPLETE (AUS)
*********************
A-4734-568-A MAIN BOARD, COMPLETE (E3, E15)
*********************
A-4734-597-A MAIN BOARD, COMPLETE (TH)
*********************
A-4734-805-A MAIN BOARD, COMPLETE (RU)
*********************
1/10W
1/10W
1/10W
1/10W
1/10W
< SWITCH >
S637
1-771-879-11 SWITCH, TACTILE (PUSH ENTER)
************************************************************
1-687-208-11 HP AMP BOARD
*************
< CONNECTOR >
CN601
1-785-329-11 PIN, CONNECTOR (LIGHT ANGLE)3P
< TERMINAL >
EP601
1-537-738-21 TERMINAL, GROUND
< CAPACITOR >
C102
C104
C106
C107
1-126-964-11
1-124-261-00
1-164-227-11
1-164-227-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
10uF
10uF
0.022uF
0.022uF
20.00%
20%
10%
10%
50V
50V
25V
25V
83
HCD-WZ8D
MAIN
Ref. No.
Part No.
Description
Remarks
C108
1-126-964-11 ELECT
10uF
20.00% 50V
C109
C110
C111
C112
C113
1-110-563-11
1-162-968-11
1-126-964-11
1-137-189-11
1-136-171-00
0.068uF
0.0047uF
10uF
0.18uF
0.33uF
10.00%
10%
20.00%
5.00%
5.00%
C114
C123
C124
1-124-261-00 ELECT
1-104-665-11 ELECT
1-124-261-00 ELECT
C125
C126
1-164-156-11 CERAMIC CHIP
1-104-665-11 ELECT
20%
50V
20.00% 10V
20%
50V
(EXCEPT AEP, UK, RU)
0.1uF
25V
100uF
20.00% 10V
C129
C133
C134
C140
C152
1-126-964-11
1-126-964-11
1-126-967-11
1-126-960-11
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
10uF
47uF
1uF
10uF
20.00%
20.00%
20.00%
20.00%
20.00%
50V
50V
50V
50V
50V
C154
C156
C157
C158
C159
1-124-261-00
1-164-227-11
1-164-227-11
1-126-964-11
1-110-563-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
10uF
0.022uF
0.022uF
10uF
0.068uF
20%
10%
10%
20.00%
10.00%
50V
25V
25V
50V
16V
C160
C161
C162
C163
C164
1-162-968-11
1-126-964-11
1-137-189-11
1-136-171-00
1-124-261-00
CERAMIC CHIP
ELECT
FILM
FILM
ELECT
0.0047uF
10uF
0.18uF
0.33uF
10uF
10%
20.00%
5.00%
5.00%
20%
50V
50V
50V
50V
50V
C165
C166
C170
C171
C172
1-126-964-11
1-104-665-11
1-162-919-11
1-162-960-11
1-126-964-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
10uF
100uF
22PF
220PF
10uF
20.00%
20.00%
5%
10%
20.00%
50V
10V
50V
50V
50V
C173
C174
C175
C177
C179
1-162-960-11
1-126-964-11
1-164-156-11
1-126-926-11
1-124-261-00
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
220PF
10uF
0.1uF
1000uF
10uF
10%
50V
20.00% 50V
25V
20.00% 10V
20%
50V
C180
C181
C182
C183
C184
1-216-864-11
1-162-960-11
1-126-964-11
1-162-960-11
1-126-964-11
METAL CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0
220PF
10uF
220PF
10uF
5%
10%
20.00%
10%
20.00%
1/10W
50V
50V
50V
50V
C187
C189
C190
C193
C194
1-126-926-11
1-124-261-00
1-162-919-11
1-126-926-11
1-104-665-11
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
1000uF
10uF
22PF
1000uF
100uF
20.00%
20%
5%
20.00%
20.00%
10V
50V
50V
10V
10V
C198
C220
1-126-960-11 ELECT
1-104-665-11 ELECT
1uF
100uF
C221
C222
C225
1-104-665-11 ELECT
1-164-156-11 CERAMIC CHIP
1-162-974-11 CERAMIC CHIP
100uF
0.1uF
0.01uF
C226
C227
C242
C244
C253
1-162-974-11
1-162-974-11
1-164-156-11
1-164-156-11
1-126-960-11
0.01uF
0.01uF
0.1uF
0.1uF
1uF
CERAMIC CHIP
CERAMIC CHIP
ELECT
FILM
FILM
16V
50V
50V
50V
50V
10uF
100uF
10uF
Ref. No.
Part No.
Description
C254
C255
C270
C271
C272
1-126-964-11
1-164-156-11
1-104-665-11
1-104-665-11
1-104-665-11
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
10uF
0.1uF
100uF
100uF
100uF
20.00% 50V
25V
20.00% 10V
20.00% 10V
20.00% 10V
Remarks
C292
C293
C294
C400
C401
1-136-165-00
1-136-165-00
1-126-964-11
1-164-156-11
1-164-156-11
FILM
FILM
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
10uF
0.1uF
0.1uF
5.00% 50V
5.00% 50V
20.00% 50V
25V
25V
C402
C403
C410
C411
C412
1-164-156-11
1-164-156-11
1-162-918-11
1-162-917-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
18PF
15PF
0.1uF
25V
25V
5.00% 50V
5%
50V
25V
C416
C417
C452
C462
C463
1-164-156-11
1-104-656-11
1-164-156-11
1-104-665-11
1-162-974-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
2200uF
0.1uF
100uF
0.01uF
25V
20.00% 6.3V
25V
20.00% 10V
50V
C475
C476
C497
C498
C499
1-162-974-11
1-162-974-11
1-164-156-11
1-126-964-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.01uF
0.01uF
0.1uF
10uF
0.1uF
50V
50V
25V
20.00% 50V
25V
< CONNECTOR >
CN101
CN102
CN103
CN104
CN104
CN105
CN105
1-779-275-11 CONNECTOR, FFC (LIF (NON-ZIF)) 7P
1-779-279-11 CONNECTOR, FFC (LIF (NON-ZIF)) 11P
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-779-273-11 CONNECTOR, FFC (LIF (NON-ZIF)) 5P
1-784-776-11 CONNECTOR, FFC 15P (AEP, UK)
1-568-830-11 CONNECTOR, FFC 11P (EXCEPT AEP, UK)
CN107
CN108
CN109
1-784-786-11 CONNECTOR, FFC 25P (AEP, UK, RU, AUS)
1-784-784-11 CONNECTOR, FFC 23P
(EXCEPT AEP, UK, RU, AUS)
1-691-907-11 PIN, CONNECTOR 15P
1-785-321-11 PIN, CONNECTOR (STRAIGHT) 9P
1-784-784-11 CONNECTOR, FFC 23P
CN110
CN111
CN401
1-770-827-21 CONNECTOR, BOARD TO BOARD 16P
1-573-847-11 CONNECTOR, BOARD TO BOARD 15P
1-785-316-11 PIN, CONNECTOR (STRAIGHT) 4P
< DIODE >
84
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
20.00% 50V
20.00% 10V
(AEP, UK, RU, AUS)
20.00% 10V
25V
50V
50V
50V
25V
25V
20.00% 50V
D191
D192
D193
D201
D202
8-719-058-24
8-719-058-24
8-719-988-61
8-719-988-61
8-719-988-61
DIODE RB501V-40TE-17
DIODE RB501V-40TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17 (EXCEPT TH)
D252
D284
D292
D293
D294
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE 1SS355TE-17 (AEP, UK)
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
DIODE 1SS355TE-17
D295
D402
D403
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
HCD-WZ8D
MAIN
Ref. No.
Part No.
Description
Remarks
< TERMINAL >
EP102
1-500-445-21 FERRITE
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
0uH
0
0
5%
5%
1/10W
1/10W
< IC >
IC101
IC103
IC201
IC202
IC251
IC401
IC401
6-703-650-11 IC M61529FP-D60G
8-759-545-66 IC NJM3414AM-TE2
8-749-019-25 IC TOTX141 (DVD DIGITAL OUT (OPTICAL))
(AEP, UK, RU, AUS)
8-759-598-69 IC BA6956AN
8-759-532-64 IC M62703SL-TP
6-803-530-01 IC M30622MGN-B24FP (AEP, UK, RU, E2)
6-803-531-01 IC M30622MGN-B25FP
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
< JACK >
J101
1-794-212-11 JACK, PIN 4P (MD (VIDEO) IN/OUT)
< JUMPER RESISTOR >
JR1
JR21
JR418
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
0
0
0
JR440
1-216-864-11 METAL CHIP
0
5%
1/10W
5%
1/10W
5%
1/10W
(EXCEPT AEP, UK, RU)
5%
1/10W
(EXCEPT AEP, UK, RU)
< COIL >
L220
Part No.
Description
Remarks
R104
R105
1-216-819-11 METAL CHIP
1-216-845-11 METAL CHIP
680
100K
5%
5%
1/10W
1/10W
R106
R112
R113
R114
R115
1-216-864-11
1-216-833-11
1-216-833-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
10K
10K
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R140
R149
R150
R151
R152
1-216-857-11
1-216-801-11
1-216-841-11
1-216-825-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
22
47K
2.2K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R153
R154
R155
R156
R159
1-216-833-11
1-216-819-11
1-216-845-11
1-216-864-11
1-216-801-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
680
100K
0
22
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R160
R166
R167
R168
R171
1-216-841-11
1-216-827-11
1-216-828-11
1-216-815-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
3.3K
4.3K
330
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R172
R173
R174
R175
R176
1-216-845-11
1-216-829-11
1-216-845-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
4.7K
100K
10K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R177
R178
R179
R180
R181
1-216-845-11
1-216-821-11
1-216-801-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
1K
22
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R182
R183
R184
R185
R186
1-216-845-11
1-216-829-11
1-216-845-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
4.7K
100K
10K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R187
R188
R189
R190
R193
1-216-845-11
1-216-821-11
1-216-801-11
1-216-833-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
1K
22
10K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R194
R195
R196
R197
R198
1-216-843-11
1-216-809-11
1-216-815-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
68K
100
330
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R199
R221
R222
R241
1-216-845-11
1-216-821-11
1-216-819-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
1K
680
0
R241
1-216-833-11 METAL CHIP
10K
5%
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
(EXCEPT E2, TH)
5%
1/10W
(E2)
R242
1-216-845-11 METAL CHIP
100K
5%
R270
R271
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
1K
5%
5%
1-537-738-21 TERMINAL, GROUND
< FERRITE BEAD >
FB416
FB462
FB499
Ref. No.
1-412-064-11 INDUCTOR
100uH (AEP, UK, RU, AUS)
< TRANSISTOR >
Q101
Q151
Q161
Q171
Q181
8-729-120-28
8-729-120-28
8-729-141-73
8-729-141-73
8-729-141-73
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1623-T1-L5L6
2SC1623-T1-L5L6
2SC3624A-T1L15L16
2SC3624A-T1L15L16
2SC3624A-T1L15L16
Q182
Q191
Q270
Q271
Q272
8-729-026-68
8-729-120-28
8-729-141-73
8-729-141-73
8-729-027-23
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD2525 (TP)
2SC1623-T1-L5L6
2SC3624A-T1L15L16
2SC3624A-T1L15L16
DTA114EKA-T146
Q273
Q274
Q275
Q276
Q277
8-729-900-53
8-729-027-23
8-729-900-53
8-729-027-23
8-729-900-53
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EKA-T146
DTA114EKA-T146
DTC114EKA-T146
DTA114EKA-T146
DTC114EKA-T146
Q293
Q401
8-729-120-28 TRANSISTOR
8-729-027-23 TRANSISTOR
2SC1623-T1-L5L6
DTA114EKA-T146
(EXCEPT AEP, UK, RU)
< RESISTOR >
R101
R102
R103
1-216-825-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
2.2K
10K
10K
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
(E2)
1/10W
1/10W
85
HCD-WZ8D
MAIN
Ref. No.
Part No.
Description
Remarks
R273
R274
1-216-813-11 METAL CHIP
1-216-821-11 METAL CHIP
220
1K
5%
5%
R275
R277
R279
R280
R291
1-216-821-11
1-216-813-11
1-216-813-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
220
220
0
0
5%
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
(EXCEPT E2, TH)
R291
1-216-833-11 METAL CHIP
10K
5%
R292
1-216-845-11 METAL CHIP
100K
5%
R294
R295
R296
1-216-833-11 METAL CHIP
1-216-837-11 METAL CHIP
1-216-837-11 METAL CHIP
10K
22K
22K
5%
5%
5%
R297
R298
R299
R400
1-216-829-11
1-216-813-11
1-216-833-11
1-216-833-11
4.7K
220
10K
10K
R401
1-216-864-11 METAL CHIP
R402
R404
R405
1-216-833-11 METAL CHIP
10K
5%
1/10W
1-216-809-11 METAL CHIP
100
5%
1/10W
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
R406
R407
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
1/10W
1/10W
1/10W
(E2)
1/10W
(E2)
1/10W
1/10W
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
(EXCEPT AEP, UK, RU)
5%
1/10W
(AEP, UK, RU)
R408
R409
R410
R411
R412
1-216-833-11
1-216-833-11
1-216-833-11
1-216-851-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
330K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R413
R414
R415
R416
R417
1-216-864-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R418
1-216-809-11 METAL CHIP
100
5%
R420
R421
1-216-829-11
1-216-809-11
R422
1-216-809-11
R423
1-216-809-11
R424
R429
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
R430
R431
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
R425
R426
R427
86
1/10W
(AEP, UK)
METAL CHIP
4.7K
5%
1/10W
METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
METAL CHIP
100
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
100
100
5%
5%
1/10W
1/10W
Ref. No.
Part No.
Description
Remarks
R433
R434
R435
1-216-809-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-809-11 METAL CHIP
100
10K
100
5%
5%
5%
1/10W
1/10W
1/10W
R436
R437
R438
R439
R440
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
(AEP, UK)
R441
R442
R443
R444
R445
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R446
R447
R448
R449
R450
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R451
R452
1-216-857-11 METAL CHIP
1-216-809-11 METAL CHIP
1M
100
R453
R454
R455
1-216-833-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
10K
100
100
R456
R457
R458
R459
R460
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R461
R462
R463
R464
R465
1-216-809-11
1-216-833-11
1-216-809-11
1-216-833-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
100
10K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R466
R467
R468
R469
R470
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R471
R472
R473
R474
R475
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R476
R478
R479
R480
R481
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R482
R483
R484
R485
R486
1-216-809-11
1-216-809-11
1-216-809-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R487
R488
R489
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
100
100
100
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
5%
1/10W
(EXCEPT AEP, UK, RU)
5%
1/10W
5%
1/10W
5%
1/10W
HCD-WZ8D
MAIN
Ref. No.
Part No.
Description
Remarks
R490
R491
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
100
100
R492
R493
1-216-809-11 METAL CHIP
1-216-829-11 METAL CHIP
100
4.7K
R493
1-216-823-11 METAL CHIP
1.5K
R493
1-216-864-11 METAL CHIP
0
R493
1-216-821-11 METAL CHIP
1K
330
5%
5%
1/10W
1/10W
5%
1/10W
5%
1/10W
(AEP, UK, RU, E2)
5%
1/10W
(AUS)
5%
1/10W
(MY, SP, KR, TH, PH)
5%
1/10W
(EA)
R493
1-216-815-11 METAL CHIP
5%
1/10W
(E3, E15)
METAL CHIP
470
5%
1/10W
METAL CHIP
470
5%
1/10W
METAL CHIP
0
5%
1/10W
(AEP, UK)
METAL CHIP
4.7K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
R494
R495
R496
1-216-817-11
1-216-817-11
1-216-864-11
R496
1-216-829-11
R496
1-216-821-11 METAL CHIP
1K
5%
R496
1-216-811-11 METAL CHIP
150
5%
R497
R498
R499
1-216-833-11 METAL CHIP
1-216-835-11 METAL CHIP
1-216-835-11 METAL CHIP
10K
15K
15K
5%
5%
5%
1/10W
(E2)
1/10W
(RU)
1/10W
1/10W
1/10W
Ref. No.
Part No.
Description
MIC
Remarks
C712
1-136-167-00 FILM
0.15uF
5.00% 50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
CERAMIC CHIP 0.0068uF 10%
25V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
ELECT
1uF
20.00% 50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
CERAMIC CHIP 0.022uF 10%
25V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
ELECT
2.2uF
20.00% 50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
C713
1-162-969-11
C714
1-126-960-11
C715
1-164-227-11
C716
1-126-961-11
C717
1-124-261-00 ELECT
C719
1-126-961-11 ELECT
C721
1-162-953-11 CERAMIC CHIP
C722
1-126-964-11 ELECT
C723
1-162-949-11 CERAMIC CHIP
C724
1-126-961-11 ELECT
C725
1-126-957-11
C725
C726
1-126-956-91
1-162-957-11
C726
1-164-362-11
C727
1-162-949-11 CERAMIC CHIP 47PF
5%
50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-162-964-11 CERAMIC CHIP 0.001uF 10%
50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-126-957-11 ELECT
0.22uF
20.00% 50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-162-974-11 CERAMIC CHIP 0.01uF
50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-162-974-11 CERAMIC CHIP 0.01uF
50V
(EXCEPT AEP, UK, RU)
10uF
20%
50V
(EXCEPT AEP, UK, RU)
2.2uF
20.00% 50V
(EXCEPT AEP, UK, RU)
100PF
5%
50V
(EXCEPT AEP, UK, RU)
10uF
20.00% 50V
(EXCEPT AEP, UK, RU)
47PF
5%
50V
(EXCEPT AEP, UK, RU)
2.2uF
20.00% 50V
(EXCEPT AEP, UK, RU)
ELECT
0.22uF
20.00% 50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
ELECT
0.1uF
20.00% 50V (E2)
CERAMIC CHIP 220PF
5%
50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
CERAMIC CHIP 470PF
5.00% 50V (E2)
< VIBRATOR >
X401
1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
X402
1-781-107-21 VIBRATOR, SERAMIC (16MHz)
************************************************************
C728
C729
A-4732-216-A MIC BOARD, COMPLETE (E2)
********************
A-4732-322-A MIC BOARD, COMPLETE
(E3, E15, EA, MY, SP, KR, PH, AUS)
********************
A-4734-601-A MIC BOARD, COMPLETE (TH)
********************
< CAPACITOR >
C701
1-124-465-00 ELECT
0.47uF
20%
50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
ELECT
0.47uF
20%
50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
FILM
0.068uF 5.00% 50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
CERAMIC CHIP 0.001uF 10%
50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
CERAMIC CHIP 0.0068uF 10%
25V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
C702
1-124-465-00
C703
1-136-495-11
C704
1-162-964-11
C705
1-162-969-11
C706
1-126-960-11 ELECT
C708
1-124-589-11
C709
1-124-589-11
C710
1-136-495-11
C711
1-162-964-11
1uF
20.00% 50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
ELECT
47uF
20%
16V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
ELECT
47uF
20%
16V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
FILM
0.068uF 5.00% 50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
CERAMIC CHIP 0.001uF 10%
50V
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
C730
C731
C732
1-126-957-11 ELECT
C736
1-126-934-11 ELECT
0.22uF
20.00% 50V
(EXCEPT AEP, UK, RU)
220uF
20.00% 10V
(EXCEPT AEP, UK, RU)
< CONNECTOR >
CN701
1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4P
(EXCEPT AEP, UK, RU)
< DIODE >
D702
8-719-069-54 DIODE UDZSTE-175.1B
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
< TERMINAL >
EP701
1-537-738-21 TERMINAL, GROUND (EXCEPT AEP, UK, RU)
< IC >
IC701
IC702
8-759-496-41 IC M65850FP-E1
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
8-759-656-83 IC NJM4580MD- (TE2)(EXCEPT AEP, UK, RU)
87
HCD-WZ8D
MIC
Ref. No.
MS-128
Part No.
PANEL
Description
Remarks
< JACK >
J701
J702
1-770-226-11 JACK (LARGE TYPE)(MIC1)
(EXCEPT AEP, UK, RU)
1-770-226-11 JACK (LARGE TYPE)(MIC2)
(EXCEPT AEP, UK, RU, E2)
< RESISTOR >
R710
R711
R712
R713
R714
R715
R716
R718
R719
R720
R721
R721
R722
R723
R724
R725
R726
R727
R733
R734
1-216-835-11 METAL CHIP
15K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-835-11 METAL CHIP
15K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-864-11 METAL CHIP
0
5%
1/10W
(EXCEPT AEP, UK, RU)
1-216-845-11 METAL CHIP
100K
5%
1/10W
(EXCEPT AEP, UK, RU)
1-216-833-11 METAL CHIP
10K
5%
1/10W
(E2, E3, E15, EA, MY, SP, KR, PH, AUS)
1-216-833-11 METAL CHIP
10K
5%
1/10W
(E2, E3, E15, EA, MY, SP, KR, PH, AUS)
1-216-809-11 METAL CHIP
100
5%
1/10W
(E2, E3, E15, EA, MY, SP, KR, PH, AUS)
1-216-847-11 METAL CHIP
150K
5%
1/10W
(EXCEPT AEP, UK, RU)
1-216-833-11 METAL CHIP
10K
5%
1/10W
(EXCEPT AEP, UK, RU)
1-216-809-11 METAL CHIP
100
5%
1/10W
(EXCEPT AEP, UK, RU)
1-216-841-11 METAL CHIP
47K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-837-11 METAL CHIP
22K
5%
1/10W
(E2)
1-216-821-11 METAL CHIP
1K
5%
1/10W
(EXCEPT AEP, UK, RU)
1-216-845-11 METAL CHIP
100K
5%
1/10W
(EXCEPT AEP, UK, RU)
1-216-821-11 METAL CHIP
1K
5%
1/10W
(E3, E15, EA, MY, SP, KR, PH, AUS)
1-216-833-11 METAL CHIP
10K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-833-11 METAL CHIP
10K
5%
1/10W
(EXCEPT AEP, UK, RU)
1-216-821-11 METAL CHIP
1K
5%
1/10W
(EXCEPT AEP, UK, RU)
1-216-837-11 METAL CHIP
22K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-837-11 METAL CHIP
22K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
Ref. No.
R742
Part No.
Description
Remarks
1-216-833-11 METAL CHIP
10K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
< VARIABLE RESISTOR >
RV701
1-223-984-11 RES, VAR, CARBON 50K (ECHO LEVEL)
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
RV702 1-223-984-11 RES, VAR, CARBON 50K (MIC LEVEL)
(EXCEPT AEP, UK, RU)
************************************************************
MS-128 BOARD
*************
< CONNECTOR >
CN001
1-815-412-11 CONNECTOR, FFCI FPC 5P
< SWITCH >
S001
1-786-357-12 SWITCH, LEVER (SLIDE)
************************************************************
A-4732-210-A PANEL BOARD, COMPLETE (EXCEPT TH)
**********************
A-4734-616-A PANEL BOARD, COMPLETE (TH)
**********************
< CAPACITOR >
C601
C603
C604
C605
C606
1-126-947-11
1-162-971-11
1-162-971-11
1-162-971-11
1-162-971-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
0.001uF
0.001uF
0.001uF
0.001uF
20.00%
10.00%
10.00%
10.00%
10.00%
16V
50V
50V
50V
50V
< CONNECTOR >
CN603
CN604
CN605
1-785-329-11 PIN, CONNECTOR (LIGHT ANGLE) 3P
1-785-328-11 PIN, CONNECTOR (LIGHT ANGRE) 2P
1-784-784-11 CONNECTOR, FFC 23P
< DIODE >
D601
D602
D603
D604
D605
8-719-058-04
8-719-058-03
6-500-327-01
6-500-327-01
6-500-327-01
DIODE SEL5223S-TP15 (I/1)
DIODE SEL5423E-TP15 (gG)
DIODE SEL5E23C-STP15 (MD (VIDEO))
DIODE SEL5E23C-STP15 (TAPE A/B)
DIODE SEL5E23C-STP15 (DVD)
D606
6-500-327-01 DIODE SEL5E23C-STP15 (TUNER/BAND)
< IC >
R735
R736
R737
R738
R739
R740
R741
88
1-216-837-11 METAL CHIP
22K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-813-11 METAL CHIP
220
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-846-11 METAL CHIP
120K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-837-11 METAL CHIP
22K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-837-11 METAL CHIP
22K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-837-11 METAL CHIP
22K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-216-841-11 METAL CHIP
47K
5%
1/10W
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
IC601
6-600-210-01 IC RPM7240-H8 (g)
< JUMPER RESISTOR >
JR605
JR606
JR607
JR608
JR609
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
JR610
JR611
JR612
JR613
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
HCD-WZ8D
PANEL
Ref. No.
Part No.
Description
Remarks
Ref. No.
< TRANSISTOR >
Q601
Q602
Q603
Q604
Q605
8-729-900-53
8-729-900-53
8-729-900-53
8-729-900-53
8-729-900-53
TRANSISTOR DTC114EKA-T146
TRANSISTOR DTC114EKA-T146
TRANSISTOR DTC114EKA-T146
TRANSISTOR DTC114EKA-T146
TRANSISTOR DTC114EKA-T146
Q606
Q608
Q609
Q611
8-729-900-53
8-729-120-28
8-729-120-28
8-729-120-28
TRANSISTOR DTC114EKA-T146
TRANSISTOR 2SC1623-T1-L5L6
TRANSISTOR 2SC1623-T1-L5L6
TRANSISTOR 2SC1623-T1-L5L6
REGULATOR
Part No.
Description
R675
R676
R678
R679
R680
1-216-821-11
1-216-821-11
1-216-864-11
1-216-864-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
0
0
2.2K
5%
5%
5%
5%
5%
Remarks
1/10W
1/10W
1/10W
1/10W
1/10W
R681
R682
R683
1-216-825-11 METAL CHIP
1-216-825-11 METAL CHIP
1-216-825-11 METAL CHIP
2.2K
2.2K
2.2K
5%
5%
5%
1/10W
1/10W
1/10W
< SWITCH >
< RESISTOR >
R601
R602
R603
R604
R605
1-216-821-11
1-216-821-11
1-216-823-11
1-216-823-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1.5K
1.5K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R606
R614
R621
R622
R623
1-216-823-11
1-216-864-11
1-216-819-11
1-216-821-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
0
680
1K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R624
R625
R626
R627
R628
1-216-823-11
1-216-825-11
1-216-827-11
1-216-829-11
1-218-867-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
2.2K
3.3K
4.7K
6.8K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R629
R630
R631
R632
R637
1-216-833-11
1-216-835-11
1-216-837-11
1-216-839-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
15K
22K
33K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R638
R639
R640
R641
R642
1-216-823-11
1-216-823-11
1-216-823-11
1-216-819-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
1.5K
1.5K
680
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R643
R644
R645
1-216-823-11 METAL CHIP
1-216-823-11 METAL CHIP
1-216-825-11 METAL CHIP
1.5K
1.5K
2.2K
5%
5%
5%
1/10W
1/10W
1/10W
S601
S602
S603
S611
S612
1-476-504-11
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
ENCODER, ROTARY (VOLUME)
SWITCH, KEYBOARD (DISPLAY)
SWITCH, KEYBOARD (I/1)
SWITCH, KEYBOARD (TUNER/BAND)
SWITCH, KEYBOARD (DVD)
S613
S614
S615
S616
S617
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (TAPE A/B)
SWITCH, KEYBOARD (MD (VIDEO)
SWITCH, KEYBOARD (.m–)
SWITCH, KEYBOARD (+M>)
SWITCH, KEYBOARD (MUSIC MODE)
S618
S619
S620
S621
S622
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (MOVIE MODE)
SWITCH, KEYBOARD (SOUND FIELD)
SWITCH, KEYBOARD (GROOVE)
SWITCH, KEYBOARD (x)
SWITCH, KEYBOARD (gG)
S623
S631
S632
S633
S634
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (X)
SWITCH, KEYBOARD (COLOR SELECT)
SWITCH, KEYBOARD (EQ EDIT)
SWITCH, KEYBOARD (EFFECT)
SWITCH, KEYBOARD (KARAOKE/MPX)
(EXCEPT AEP, UK RU)
S634
S635
1-762-875-21 SWITCH, KEYBOARD (MPX)(AEP, UK, RU)
1-762-875-21 SWITCH, KEYBOARD
(DVD TOP MENU, ALBUM–)
S636
1-762-875-21 SWITCH, KEYBOARD (DVD MENU, ALBUM+)
************************************************************
A-4732-208-A REGULATOR BOARD, COMPLETE (EXCEPT TH)
***************************
A-4734-612-A REGULATOR BOARD, COMPLETE (TH)
***************************
4-931-401-01 HEAT SINK, V.OUT
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
*
< RESISTOR >
R654
R655
R656
R657
R658
1-216-821-11
1-216-821-11
1-216-821-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R659
R660
R661
R662
R664
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R665
R671
R672
R673
R674
1-216-821-11
1-216-823-11
1-216-823-11
1-216-823-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1.5K
1.5K
1.5K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< CAPACITOR >
C501
C503
C506
C509
C521
1-162-965-11
1-124-261-00
1-128-131-11
1-124-261-00
1-124-584-00
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.0015uF
10uF
22uF
10uF
100uF
10%
20%
20.00%
20%
20%
50V
50V
50V
50V
10V
C522
C523
C551
C553
C556
1-164-156-11
1-128-131-11
1-162-965-11
1-124-261-00
1-128-131-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
0.1uF
22uF
0.0015uF
10uF
22uF
20.00%
10%
20%
20.00%
25V
50V
50V
50V
50V
C559
C583
C584
C585
1-124-261-00
1-126-160-11
1-126-935-11
1-104-665-11
ELECT
ELECT
ELECT
ELECT
10uF
1uF
470uF
100uF
20%
20%
20.00%
20.00%
50V
50V
10V
10V
89
HCD-WZ8D
REGULATOR
Ref. No.
Part No.
Description
Remarks
C586
1-162-945-11 CERAMIC CHIP
22PF
5%
50V
C587
C588
C589
C590
C901
1-130-483-00
1-130-483-00
1-126-964-11
1-126-965-91
1-126-964-11
MYLAR
MYLAR
ELECT
ELECT
ELECT
0.01uF
0.01uF
10uF
22uF
10uF
5%
5%
20.00%
20.00%
20.00%
50V
50V
50V
50V
50V
C902
C903
C904
C905
C906
1-126-916-11
1-126-956-91
1-126-926-91
1-130-483-00
1-130-483-00
ELECT
ELECT
ELECT
MYLAR
MYLAR
1000uF
0.1uF
1000uF
0.01uF
0.01uF
20.00%
20.00%
20.00%
5%
5%
6.3V
50V
10V
50V
50V
C907
C909
C910
C911
C912
1-119-939-51
1-126-952-11
1-165-718-21
1-126-926-91
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
6800uF
1000uF
3300uF
1000uF
10uF
20.00%
20.00%
20%
20.00%
20.00%
35V
35V
6.3V
10V
50V
C913
C914
C915
C919
C920
1-126-767-11
1-126-927-11
1-126-956-91
1-126-952-11
1-128-947-21
ELECT
ELECT
ELECT
ELECT
ELECT
1000uF
2200uF
0.1uF
1000uF
3300uF
20.00%
20.00%
20.00%
20.00%
20%
16V
10V
50V
35V
10V
C921
C923
C924
C926
C927
1-126-926-91
1-126-916-11
1-126-916-11
1-126-947-11
1-162-974-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
1000uF
1000uF
1000uF
47uF
0.01uF
20.00%
20.00%
20.00%
20.00%
10V
6.3V
6.3V
16V
50V
C928
C929
1-162-974-11 CERAMIC CHIP
1-164-156-11 CERAMIC CHIP
0.01uF
0.1uF
Ref. No.
Part No.
Description
IC581
IC901
IC902
IC903
8-759-100-96
8-759-701-59
8-759-701-59
6-700-813-01
IC NJM4558M-TE2
IC TA7809S
IC TA7809S
IC SI-8033JF
Remarks
IC904
IC905
IC906
IC913
8-759-518-68
8-759-231-53
8-759-450-47
6-700-812-01
IC PQ12RF21
IC TA7805S
IC BA05T
IC SI-8050JF
< JUMPER RESISTOR >
JR500
JR501
JR502
JR503
JR504
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
JR505
JR506
JR507
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
0
0
0
5%
5%
5%
1/10W
1/10W
1/10W
< COIL >
L901
L911
L912
L913
1-456-467-11
1-456-468-11
1-414-398-11
1-414-398-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
150uH
100uH
10uH
10uH
< TRANSISTOR >
< CONNECTOR >
Q501
Q502
Q520
Q521
Q522
8-729-141-73
8-729-141-73
8-729-900-53
8-729-900-53
8-729-900-53
TRANSISTOR 2SC3624A-T1L15L16
TRANSISTOR 2SC3624A-T1L15L16
TRANSISTOR DTC114EKA-T146
TRANSISTOR DTC114EKA-T146
TRANSISTOR DTC114EKA-T146
CONNECTOR, BOARD TO BOARD 15P
CONNECTOR, BOARD TO BOARD 16P
PIN, CONNECTOR 8P
PIN, CONNECTOR 12P
PIN, CONNECTOR (SMALL TYPE)13P
Q523
Q524
Q551
Q552
Q581
8-729-027-23
8-729-027-23
8-729-141-73
8-729-141-73
8-729-900-53
TRANSISTOR DTA114EKA-T146
TRANSISTOR DTA114EKA-T146
TRANSISTOR 2SC3624A-T1L15L16
TRANSISTOR 2SC3624A-T1L15L16
TRANSISTOR DTC114EKA-T146
Q582
Q583
Q584
Q585
Q901
8-729-900-53
8-729-120-28
8-729-900-53
8-729-900-53
8-729-114-93
TRANSISTOR DTC114EKA-T146
TRANSISTOR 2SC1623-T1-L5L6
TRANSISTOR DTC114EKA-T146
TRANSISTOR DTC114EKA-T146
TRANSISTOR 2SB734
Q902
Q903
Q904
Q907
Q908
8-729-900-53
8-729-900-53
8-729-900-53
8-729-026-68
8-729-120-28
TRANSISTOR DTC114EKA-T146
TRANSISTOR DTC114EKA-T146
TRANSISTOR DTC114EKA-T146
TRANSISTOR 2SD2525 (TP)
TRANSISTOR 2SC1623-T1-L5L6
Q909
Q910
8-729-900-53 TRANSISTOR DTC114EKA-T146
8-729-900-53 TRANSISTOR DTC114EKA-T146
CN501
CN502
CN503
CN504
* CN506
1-573-829-11
1-770-828-41
1-568-373-11
1-794-568-11
1-564-715-11
* CN507
1-564-704-11 PIN, CONNECTOR (SMALL TYPE) 2P
< DIODE >
D581
D901
D902
D903
D905
8-719-988-61
8-719-028-23
8-719-080-53
8-719-080-53
8-719-056-85
DIODE 1SS355TE-17
DIODE D3SBA20-4101
DIODE RK36LF-B3
DIODE RK36LF-B3
DIODE UDZSTE-178.2B
D911
D912
D913
6-500-522-21 DIODE 10EDB40-TB3
6-500-522-21 DIODE 10EDB40-TB3
6-500-522-21 DIODE 10EDB40-TB3
50V
25V
< TERMINAL >
< RESISTOR >
EP502
EP901
1-537-738-21 TERMINAL, GROUND
1-537-738-21 TERMINAL, GROUND
< FERRITE BEAD >
FB912
1-410-397-21 FERRITE BEAD INDUCTOR
< IC >
IC501
90
8-759-939-73 IC BA3308
R500
R501
R502
R503
R504
1-216-813-11
1-216-845-11
1-216-809-11
1-216-833-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
100K
100
10K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R506
R507
R508
1-216-833-11 METAL CHIP
1-216-828-11 METAL CHIP
1-216-821-11 METAL CHIP
10K
3.9K
1K
5%
5%
5%
1/10W
1/10W
1/10W
HCD-WZ8D
REGULATOR
Ref. No.
Part No.
Description
Remarks
R509
R510
1-216-836-11 METAL CHIP
1-216-816-11 METAL CHIP
18K
390
5%
5%
1/10W
1/10W
R511
R512
R513
R514
R521
1-216-839-11
1-216-845-11
1-216-821-11
1-216-827-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
100K
1K
3.3K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R522
R523
R525
R551
R552
1-216-861-11
1-216-809-11
1-216-809-11
1-216-845-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2M
100
100
100K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R553
R554
R556
R557
R558
1-216-833-11
1-216-845-11
1-216-833-11
1-216-828-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
10K
3.9K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R559
R560
R561
R562
R563
1-216-836-11
1-216-816-11
1-216-839-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
18K
390
33K
100K
1K
5%
5%
5%
5%
5%
R564
R581
R582
R583
R584
1-216-827-11
1-216-845-11
1-216-845-11
1-216-832-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
100K
100K
8.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R585
R586
R587
R588
R589
1-216-833-11
1-216-821-11
1-216-821-11
1-216-861-11
1-216-835-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
1K
2.2M
15K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R590
R591
R592
R593
R594
1-216-835-11
1-216-833-11
1-216-829-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
10K
4.7K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R595
R596
R597
1-216-833-11 METAL CHIP
1-216-837-11 METAL CHIP
1-216-864-11 METAL CHIP
10K
22K
0
5%
5%
5%
R598
R900
1-216-809-11 METAL CHIP
1-216-833-11 METAL CHIP
100
10K
1/10W
1/10W
1/10W
(EXCEPT TH)
5%
1/10W
5%
1/10W
R901
R902
R903
R905
R906
1-216-825-11
1-216-825-11
1-216-825-11
1-216-864-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
2.2K
0
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R907
R908
R909
R910
R914
1-216-809-11
1-216-809-11
1-216-809-11
1-216-821-11
1-216-815-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
1K
330
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
(EXCEPT TH)
R915
1-216-810-11 METAL CHIP
120
5%
1/10W
R916
1-216-849-11 METAL CHIP
220K
5%
1/10W
R917
1-216-837-11 METAL CHIP
22K
5%
1/10W
R918
1-216-837-11 METAL CHIP
22K
5%
1/10W
R919
1-216-833-11 METAL CHIP
10K
5%
1/10W
************************************************************
Ref. No.
Part No.
Description
RF
Remarks
A-4728-690-A RF BOARD, COMPLETE
*******************
< CAPACITOR >
C001
C002
C003
C004
C005
1-126-206-11
1-124-779-00
1-126-206-11
1-124-779-00
1-128-993-21
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
100uF
10uF
100uF
10uF
22uF
20%
20%
20%
20%
20%
6.3V
16V
6.3V
16V
10V
C006
C008
C009
C010
C011
1-128-993-21
1-107-826-11
1-107-826-11
1-115-416-11
1-115-416-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.1uF
0.1uF
0.001uF
0.001uF
20%
10.00%
10.00%
5.00%
5.00%
10V
16V
16V
25V
25V
C012
C013
C014
C015
C016
1-107-826-11
1-107-826-11
1-162-966-11
1-162-966-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.0022uF
0.0022uF
0.0022uF
10.00%
10.00%
10%
10%
10%
16V
16V
50V
50V
50V
C017
C018
C019
C020
C021
1-162-966-11
1-164-172-11
1-164-172-11
1-162-919-11
1-162-919-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.0056uF
0.0056uF
22PF
22PF
10%
10.00%
10.00%
5%
5%
50V
25V
25V
50V
50V
C022
C023
C024
C025
C026
1-162-919-11
1-162-919-11
1-162-970-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
22PF
0.01uF
0.1uF
0.1uF
5%
5%
10%
10.00%
10.00%
50V
50V
25V
16V
16V
C027
C028
C029
C030
C031
1-107-826-11
1-107-826-11
1-162-970-11
1-162-970-11
1-115-416-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.01uF
0.001uF
10.00%
10.00%
10%
10%
5.00%
16V
16V
25V
25V
25V
C032
C033
C034
C035
C036
1-165-176-11
1-107-826-11
1-107-826-11
1-107-826-11
1-125-891-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.1uF
0.1uF
0.1uF
0.47uF
10.00%
10.00%
10.00%
10.00%
10.00%
16V
16V
16V
16V
10V
C037
C038
C039
C040
C041
1-162-959-11
1-164-677-11
1-164-677-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
330PF
0.033uF
0.033uF
0.1uF
0.1uF
5%
10.00%
10.00%
10.00%
10.00%
50V
16V
16V
16V
16V
C042
C049
1-164-218-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
180PF
0.1uF
0.25PF 50V
10.00% 16V
< CONNECTOR >
CN001
CN002
CN003
1-815-031-11 CONNECTOR, FFC/FPC (ZIF) 24P
1-784-836-21 CONNECTOR, FFC (LIF (NON-ZIF)) 29P
1-784-861-21 CONNECTOR, FFC (LIF (NON-ZIF)) 9P
< DIODE >
D001
D002
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
< IC >
IC001
6-703-551-01 IC CXD1881AR
91
HCD-WZ8D
RF
Ref. No.
VIDEO
Part No.
Description
Remarks
< COIL >
L001
L002
1-412-031-11 INDUCTOR CHIP 47uH
1-412-031-11 INDUCTOR CHIP 47uH
< TRANSISTOR >
Q001
Q002
8-729-903-46 TRANSISTOR 2SB1132-T100-QR
8-729-903-46 TRANSISTOR 2SB1132-T100-QR
< RESISTOR >
R001
R003
R004
R005
R006
1-218-668-11
1-216-803-11
1-216-803-11
1-216-841-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
33
33
47K
470
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R007
R008
R009
R010
R011
1-216-803-11
1-216-803-11
1-216-841-11
1-216-817-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33
33
47K
470
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R012
R013
R014
R015
R016
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R017
R018
R019
R020
R021
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R022
R023
R024
R025
R026
1-216-813-11
1-216-820-11
1-216-864-11
1-216-809-11
1-218-718-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
820
0
100
12K
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R027
R028
R029
R032
R033
1-216-864-11
1-216-864-11
1-216-864-11
1-216-809-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
100
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Ref. No.
Part No.
Description
Remarks
C809
C810
1-126-960-11 ELECT
1-126-960-11 ELECT
1uF
1uF
20.00% 50V
20.00% 50V
C811
C812
C813
C814
C815
1-107-826-11
1-126-935-11
1-104-665-11
1-126-935-11
1-104-665-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.1uF
470uF
100uF
470uF
100uF
10.00%
20.00%
20.00%
20.00%
20.00%
16V
6.3V
10V
6.3V
10V
C816
C817
C818
C819
C820
1-126-935-11
1-104-665-11
1-104-665-11
1-126-965-91
1-104-665-11
ELECT
ELECT
ELECT
ELECT
ELECT
470uF
100uF
100uF
22uF
100uF
20.00%
20.00%
20.00%
20.00%
20.00%
6.3V
10V
10V
50V
10V
C821
C822
C823
C824
C825
1-126-965-91
1-162-919-11
1-162-919-11
1-162-919-11
1-162-919-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
22PF
22PF
22PF
22PF
20.00%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C826
C827
C828
C829
C830
1-162-919-11
1-162-919-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
22PF
0.1uF
0.1uF
0.1uF
5%
5%
10.00%
10.00%
10.00%
50V
50V
16V
16V
16V
< CONNECTOR >
CN801
1-779-554-21 CONNECTOR, FFC (LIF (NON-ZIF)) 17P
< FERRITE BEAD >
FB801
FB802
FB803
FB804
FB805
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
FB806
1-216-864-11 METAL CHIP
0
5%
1/10W
< IC >
R034
1-219-570-11 METAL CHIP
10M
5%
1/10W
R035
1-216-864-11 METAL CHIP
0
5%
1/10W
R041
1-216-821-11 METAL CHIP
1K
5%
1/10W
************************************************************
A-4732-205-A VIDEO BOARD, COMPLETE (EXCEPT TH)
**********************
A-4734-606-A VIDEO BOARD, COMPLETE (TH)
**********************
1-104-665-11
1-164-360-11
1-126-965-91
1-164-360-11
1-126-960-11
C806
C807
C808
1-126-960-11 ELECT
1-126-960-11 ELECT
1-126-960-11 ELECT
92
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
100uF
0.1uF
22uF
0.1uF
1uF
20.00% 10V
16V
20.00% 50V
16V
20.00% 50V
1uF
1uF
1uF
20.00% 50V
20.00% 50V
20.00% 50V
6-702-335-01 IC MM1568AJBE
< JACK >
J801
J802
J803
1-537-943-11 TERMINAL, S (S VIDEO OUT)
1-774-227-11 JACK, PIN 1P (VIDEO OUT)
1-817-601-11 JACK, PIN 3P (COMPONENT VIDEO OUT)
< COIL >
L801
1-412-058-11 INDUCTOR CHIP 10uH
< TRANSISTOR >
Q801
Q802
< CAPACITOR >
C801
C802
C803
C804
C805
IC801
8-729-027-23 TRANSISTOR DTA114EKA-T146
8-729-900-53 TRANSISTOR DTC114EKA-T146
< RESISTOR >
R801
R802
R803
R804
R805
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-218-285-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
75
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
HCD-WZ8D
VIDEO
Ref. No.
Part No.
Description
Remarks
R806
1-218-284-11 METAL CHIP
68
5%
1/10W
R807
1-218-284-11 METAL CHIP
68
5%
1/10W
R808
1-218-284-11 METAL CHIP
68
5%
1/10W
R809
1-218-285-11 METAL CHIP
75
5%
1/10W
R810
1-218-285-11 METAL CHIP
75
5%
1/10W
************************************************************
MISCELLANEOUS
**************
54
54
54
56
57
57
58
1-775-190-11 WIRE (FLAT TYPE)(21 CORE)(TH)
1-827-402-11 WIRE (FLAT TYPE)(21 CORE)
(E2, E3, E15, EA, MY, SP, KR, PH)
1-827-403-11 WIRE (FLAT TYPE)(25 CORE)
(AEP, UK, RU, AUS)
1-827-003-11 CORD (WITH CONNECTOR) 19P
1-775-073-11 WIRE (FLAT TYPE)(7 CORE)(TH)
60
60
1-827-404-11 WIRE (FLAT TYPE)(7 CORE)(EXCEPT TH)
1-791-112-11 WIRE (FLAT TYPE)(11 CORE)
(E3, E15, EA, MY, SP, KR, TH, PH, AUS)
1-693-603-31 TUNER (FM/AM)
(E2, E3, E15, EA, MY, SP, TH, PH, AUS)
1-693-604-11 TUNER (FM/AM)(AEP, UK)
1-693-605-11 TUNER (FM/AM)(KR)
60
61
61
62
1-693-627-11
1-769-938-11
1-773-002-11
1-773-182-11
60
62
TUNER (FM/AM)(RU)
WIRE (FLAT TYPE)(11 CORE)(EXCEPT AEP, UK)
WIRE (FLAT TYPE)(15 CORE)(AEP, UK)
WIRE (FLAT TYPE)(23 CORE)
(EXCEPT AEP, UK, RU, AUS)
1-773-212-11 WIRE (FLAT TYPE)(25 CORE)
(AEP, UK, RU, AUS)
63
64
66
66
68
1-500-657-11
1-827-012-11
1-792-108-11
1-827-401-11
1-787-056-11
CORE, FERRIET
CORD (WITH CONNECTOR) 20P
WIRE (FLAT TYPE)(17 CORE)(TH)
WIRE (FLAT TYPE)(17 CORE)(EXCEPT TH)
FAN, DC
71
411
0 412
415
416
1-500-657-11
1-689-264-11
1-477-263-11
1-775-265-11
1-827-178-11
CORE, FERRITE
PWB, FLEXIBLE
OPTICAL PICK-UP
WIRE (FLAT TYPE)(29 CORE)
WIRE (FLAT TYPE)(5 CORE)
LCD201 1-805-136-11 DISPLAY PANEL, LIQUID CRYSTAL
M001
1-763-967-11 MOTOR, DC (LOADING)
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
93