Download SERVICE MANUAL - Whaley Food Service

Henny Penny
Heated Merchandiser
Model CM-5/7
Model CMT-5/7
Model HM-3/5/7
Model HMT-3/5/7
Model HS/HST-3
SERVICE MANUAL
TABLE OF CONTENTS
Section
Page
Section 1
INTRODUCTION
1-1 Heated Merchandiser
1-2 Features
1-3 Assistance
1-4 Model Variations
1-5 Safety
1-1
1-1
1-1
1-1
1-2
1-2
Section 2
INSTALLATION
2-1 Introduction
2-2 Unpacking
2-3 Electrical Connection
2-4 Electrical Data Table
2-5 Cabinet Dimensions
2-1
2-1
2-1
2-2
2-2
2-3
Section 3
OPERATION
3-1 Operating Controls
3-2 Start-Up
3-3 Operation With Product
3-4 Recommended Settings for Heated Merchandiser
3-5 Shut Down and Clean Up
3-1
3-1
3-4
3-5
3-6
3-6
Section 4
PROGRAMMING
4-1 Entering Program Mode
4-2 Programming Upper Heat
4-3 Programming Water Heat
4-4 Programming Air Temperature
4-5 Special Program Mode
4-6 Error Codes
4-1
4-1
4-1
4-1
4-1
4-1
4-2
Section 5
MAINTENANCE
5-1 Introduction
5-2 Removing Front Glass
5-3 Radiant Heaters
5-4 Light Socket
5-5 Water Heater
5-6 Base Heaters
5-7 Air Blowers
5-8 Heat Probe (Air)
5-9 Transformer
5-10 Product Probe Outlet
5-11 Heat Relay
5-1
5-1
5-1
5-3
5-3
5-4
5-5
5-6
5-6
5-7
5-7
5-8
TABLE OF CONTENTS (Continued)
Section
Page
Section 5
MAINTENANCE (Continued)
5-12 Cooling Fan
5-13 Printed Circuit Board
5-14 Gas Shocks
5-15 Fuse and Fuse Holder
5-16 Power and Light Switch
5-17 Wiring Diagrams
5-8
5-8
5-9
5-9
5-10
5-11
5-12
Section 6
TROUBLESHOOTING
6-1 Introduction
6-2 Troubleshooting
6-1
6-1
6-1
Section 7
PARTS INFORMATION
7-1
SECTION 1. INTRODUCTION
1-1. HEATED
MERCHANDISER
The Henny Penny Heated Merchandiser is a basic unit of food
processing equipment used to display the food product and
maintain the temperature of hot foods in a commercial food
service operation. Using a combination of precise heat,
humidity and slowly circulating air, Henny Penny's even heat
process creates the ideal environment to maintain the taste
and quality of freshly-cooked foods for hours.
1-2. FEATURES
• Unique THERMA-VEC even heat process re-circulates
heated air, keeping temperature precise and stable
throughout the case.
• Contemporary curved glass cases present 100 per cent
product visibility.
• Individually controlled radiant heaters over each well.
• Air heating elements under pans.
• Humidity controlled with heated water pan.
• Touch pad electronic controls and LED readouts.
• Incandescent lighting for attractive food presentation.
• Fold-down cutting board.
1-3. ASSISTANCE
Should you require outside assistance, just call your local,
independent Henny Penny distributor maintained by Henny
Penny Corporation. In addition, feel free to contact our
corporate headquarters in Eaton, Ohio. Dial 1-800-543-6243
toll free, except in Ohio, dial 1-800-762-2964.
Henny Penny
CABINET DIMENSIONS
Model CM/CIVIT- 5/7 HM/HMT- 3/5/7 HS/HST- 3 2-5
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT - 5/7 HM/HMT- 3/5/7 HS/HST-3
SECTION 3. OPERATION
3-1. OPERATING CONTROLS
This section describes the functions of all operating controls.
Item
No.
1
Description
Function
Increase Switch
The increase switch is used during programming to increase
the displayed value by one setting. It is also used to enter
special program mode.
2
Decrease Switch
The decrease switch is used during programming to decrease
the displayed value by one setting. It is also used to enter
special program mode.
3
Air Heat Switch
This switch is depressed to set the air heat temperature set
point.
4
Water Heat Switch
This switch is depressed to set the water heat.
5
Upper Heat - 1, 2, 3, 4,
These switches are depressed to set the radiant heaters.
and 5.
NOTE
HM-3 will have 1, 2, and 3.
HM-7 will have 1 through 7.
6
Temperature Display
The temperature display is a three-digit red LED display. The
display is used to show the air and product temperatures. It
is also used to display control error messages, and during
programming to show the parameter being programmed.
7
8
Ready LED
This LED turns on when the merchandiser is ready to hold
product. It turns on to indicate the air temperature is near
the set point.
Display Air Temp LED
This LED turns on when the merchandiser air temperature
is shown in the display.
9
Display Probe Temp LED
This LED turns on when the product probe temperature is
shown in the display.
10
UPPER HEAT 1, 2, 3, 4,
These LED's turn on during operation when the associated
and 5 LED's
radiant heater turns on.
NOTE
The HM-3 has three LED's.
The HM-7 has seven LED's.
Henny Penny
Item
Description
No.
11
Water Heat LED
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Function
This LED turns on during operation when the water heater
is on.
12
Air Heat LED
This LED turns on during operation when the air heater is on.
13
Power Switch
The power switch is a two-position switch used to switch
electrical current to the unit.
14
Light Switch
The light switch is a two-position switch that turns the lights
off and on.
15
Fuse
The fuse (2) is a protective device for the PCB control, motor,
and lights circuit. The fuses are a 15 amp rating and must be
replaced by a fuse of the same size and rating.
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
3-2. START-UP
Model CM/CMT.5/7 HM/HMT.3/5/7 HS/HST-3
Normal Operation
1. Turn POWER and LIGHTS to the ON position.
2. Fill water pan with approximately one quart of water (1
inch in water pan).
3. Allow approximately 30 minutes preheat time.
4. Check air temperature setting by depressing switch
marked AIR HEAT.
5. Check water temperature setting by depressing switch
marked WATER HEAT.
NOTE
Water heat settings read 1, 2, 3, etc. One meaning the
heat is on 10% of the time, and ON meaning the heat
is on 100% of the time. Refer to programming section
for correct setting changes. If you wish to operate unit
with no humidity, program water heat to OFF.
6. Check upper heat settings by depressing numbered switch
corresponding to each well.
NOTE
HM-3 is numbered 1 through 3; HM-5 is number 1
through 5; HM-7 is numbered 1 through 7. Refer to
"Recommended Settings for HM-3, HM-5, and HM-7."
7. As a rule, a lower upper heat setting, such as 3 or 4, holds
dense foods like macaroni and cheese or cherry cobbler.
Use higher upper heat settings for less dense foods, such
as fried chicken.
8. If using a probe to check product temperature, plug probe
into probe outlet (just left of the control panel) and place
probe into the product you are testing.
9. Depress switch marked PROBE TEMP DISPLAY.
Henny Penny
3-3. OPERATION WITH
PRODUCT
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
1.
Rotate food from front to back.
2.
Food in half-full pans does not hold as well as food in full
pans. Rotate pan to back of merchandiser where it is
directly under upper heating elements or move food to a
smaller pan that has been preheated.
3.
When "freshening" foods such as macaroni and cheese
with added water, heat the water in a clean container until
is it 10 to 20 degrees above the desired holding
temperature of the food. This will keep food at a safe
serving temperature. Depending on the amount of water,
the temperature can drop 10 to 20 degrees in as little as
five minutes.
4.
When transferring hot foods in the heated merchandiser
to clean pans, preheat the clean pan. Transferring hot
foods to room temperature pans can cause the temperature
of the food to drop 20 degrees or more, thus causing food
to be at an unsafe serving temperature.
5.
To keep hot foods from drying too fast, keep a clean
misting bottle (such as you find in a garden supply store)
with a mixture of 1/3 vegetable oil and 2/3 water on hand.
Set the nozzle for a fine mist. Shake the vegetable oil and
water mixture well. Spray surface of food immediately,
shaking the bottle between each entree. Frequency foods
need to be misted will depend upon the unique
characteristics of the food, the water heat setting in the
case and atmospheric conditions. Do not use this mixture
on foods with a pastry crust or crumb toppings where a
dry surface is desirable.
6.
If prepackaging foods, place containers directly under
upper heating elements (in back of the case) for maximum
holding time. Upper heat may need to be increased slightly.
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
SECTION 4. PROGRAMMING
4-1. ENTERING PROGRAM
MODE
Program mode is entered by depressing and holding a
parameter switch. Parameter switches are AIR HEAT,
WATER HEAT, and the UPPER HEAT switches.
4-2. PROGRAMMING UPPER
HEAT
Depress and hold switch marked UPPER HEAT.
Using the INCREASE or DECREASE switches, program the
desired percentage on time of the radiant heater. The display
will be numbered 1 through 9. One meaning 10%; 2 meaning
20%, etc. "OFF" means the heater is always off- "ON" means
the heater is always on. Repeat procedures until all radiant
heaters are programmed.
4-3. PROGRAMMING
WATER HEAT
The procedure for programming the water heat is identical
to that of programming the radiant heat, except that the
WATER HEAT LED flashes.
4-4. PROGRAMMING AIR
TEMPERATURE
Depress switch marked AIR HEAT.
Using the INCREASE or DECREASE button, program
desired air temperature. Air temperature can be programmed
between 120°F and 175°F.
4-5. SPECIAL PROGRAM
MODE
Special program mode is used to perform the following
functions:
• Calibrating the air and product temperature probes.
• Initializing the program.
• Changing the control for Fahrenheit 0 /Celsius".
To enter the special program mode, depress and hold the
INCREASE switch and turn the power switch to the "ON"
position. Display will read "SP" for special program. To
exit special program, turn the power switch to "OFF".
To calibrate air temperature, depress and hold the
DISPLAY AIR TEMP switch. Display will show the actual
air temperature seen by the probe. Use your
INCREASEDECREASE switch to adjust the displayed
temperature. Temperature can be adjusted plus or minus 15
degrees.
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT- 5/7 HM/HMT-3/5/7 HS/HST-3
SECTION 8. MAINTENANCE
Henny Penny
Model CM/CMT- 5/7 HM/HMT - 3/5/7
HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT.5/7 HM/HMT.3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT.5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
SECTION 6. TROUBLESHOOTING
Henny Penny
PROBLEM
With power switch in
POWER position, unit
is completely
inoperative (NO
POWER)
Unit will not heat
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
CAUSE
• Open Circuit
• Check to see that unit is
plugged in.
• Check breaker or fuse at
supply box.
• Check control panel fuses per
paragraph 5-15.
• Check voltage at wall
receptacle.
• Check MAIN POWER switch
per section 5-16.
Replace if defective.
• Check cord and plug for loose
connections
• Control board defective.
• Check for 12 volt input from
transformer. Replace if
defective.
• Transformer defective.
• Check input and output voltage
Replace if defective.
• Control board not calling
• Check set point reading. If unit
for heat.
• Power on, board has
no display.
No air heat.
CORRECTION
• Faulty heat relay.
• Faulty air heater.
• Unit not pre heated
below setpoint and not calling
for heat, control board
defective.
• Hi limit tripped. Check for
defective hi limit, or defective
blower motor.
• Check and replace per section
5-11.
• Check and replace per section
5-6.
• Pre heat unit with pans in
place before loading product.
Henny Penny
PROBLEM
No radiant heat.
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
CAUSE
CORRECTION
• Faulty input/output board.
• Replace input/output board.
• Faulty radiant heater.
• Replace radiant heater per
• Faulty input/output board.
• Replace input/output board.
• Faulty water heater.
• Replace water heater per
section 5-3.
No water heat.
section 5-5.
No lights.
• Light switch defective.
• Replace per section 5-16.
• Light relay defective
• Replace per section 5-11
( Same as heat relay )
Canopy glass fogging.
• Light socket shorted
• Replace per section 5-4.
• Light bulb blown
• Replace light bulb.
• Air blowers not circulating
• Replace blower motor per
heated air across glass.
• Water heat setting too high.
section 5-7.
• Lower water heat setting as
per section 4.
• Radiant heat setting too low.
• Raise radiant heat setting as
per section 4.
Product not holding
• Doors are left open.
temperature.
• Keep doors closed except to
load and unload product.
• Heat settings too low.
• Adjust heat settings as per
section 4.
• Low or improper voltage.
• Using meter, compare recep
tacle voltage to data plate
voltage.
• Product held too long.
• Hold product only for
recommended time.
• Product not placed correctly
in unit.
• Place product in unit as per
section 3-3.
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
SECTION 6. PARTS INFORMATION
HM-3/5/7 Service Parts List
No.
Part
Number
Description
3
1
1
1
1
1
1
1
2
2
2
3
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
18
18
19
20
21
21
22
22
23
23
24
24
25
25
26
26
26
26
28
29
30
31
31
32
33
37000
54033.
37001
54031
39027
54129
54130
37972
37973
39114
37638
41507
40833*
42440*
39216
40097
28979
PL01-006*
18135
MS01-162
22609
22610
ME50-003*
NS03-013*
EF02-040*
37230
37757
42969
43794
39974
16685
37059
44976
37060
48020
39795
54041
BL01-009
BL01-015
54181
64257
38413
37536
37537
38412
37127*
30723 *
52843
37815
42341
16688
37128
Front Viewing Glass - 3 Pan (Before July 1, 1994)
Front Viewing Glass Assy. - Complete - 3 Pan
Front Viewing Glass Assy. - 5 Pan (Before July 1,1994)
Front Viewing Glass Assy. - Complete - 5 Pan
Front Viewing Glass Assy. - 7 Pan (Before July 1,1994)
Front Viewing Glass Assy. Complete - RH - 7 Pan
Front Viewing Glass Assy. Complete - LH - 7 Pan
Sliding Door Assembly - 3 Pan
Sliding Door Assembly - 5 Pan
Sliding Door Assembly - 7 Pan
Water Pan Assembly (Before July 1, 1994)
Water Pan Assembly
Probe Bracket
Temperature Probe PC Board Assy.
Blower Motor
Series Regulating Thermostat
Transformer
Plug - Bottom
End Clamp
Mounting Channel
Terminal Block
Barrier
Spacer
Cage Nut
Bushing - Snap
Bracket - Drop Shelf
Side Viewing Panel
Side Viewing Panel - (Mir)-Left
Side Viewing Panel - (Mir)-Right
Fan Blade
Fan Guard
Heater - Lower - 240v
Heater - Lower - 208v
Heater - Water - 240v
Heater-Water-208v.
Light Socket
Light Socket - CE
Light Bulb- 120v- lOOw
Light Bulb - 240v - 60w
Heater - Upper Radiant - 240v
Heater - Upper Radiant - 208v
Decal - Control Panel - 7 Pan - Left
Decal - Control Panel - 3 Pan
Decal - Control Panel - 5 Pan
Decal - Control Panel - 7 Pan
Bracket for Plug
Relay - 3 Pan
Probe- 5 ft.
Receptacle Assy. - Probe (Control Panel)
Receptacle Assy. - Probe (Uprights)
Cooling Fan
Gas Shock - 3 Pan (Before May 1, 1994)
1
1
2
1
1
1
1
2
2
1
2
2
3
2
2
4
2
2
2
2
2
2
4
2
2
1
1
6
6
6
6
3
3
1
1
1
1
1
2
1
2
*not shown
**Front Viewing Glass before July 1, 1994, 02736 Tape Kit must also be ordered.
Qty. Per Unit
5
7
1
1
2
1
1
1
1
2
2
1
2
2
3
2
2
4
2
2
2
2
2
2
4
3
3
1
1
10
10
10
10
5
5
1
1
2
1
1
2
1
-
2
1
1
2
2
2
2
2
3
2
2
2
2
3
2
2
4
2
4
2
2
2
3
5
4
4
2
2
14
14
14
14
7
7
1
1
3
4
3
3
2
1
2
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
HM-3/5/7 Service Parts List - Continued
No.
33
33
33
33
34
34
34
34
35
35
35
36
37
38
39
39
40
40
40
41
41
42
43
43
44
44
44
44
45
45
45
46
46
47
47
48
48
49
51
52
53
53
53
54
54
54
55
55
55
55
55
58
59
60
*not shown
Part
Number
37129
41751
41750
42620
43258
39181
43262
39840
37841
37849
41233
PN01-016*
PN01-017*
LW01-004*
37044
41760
37231
42088
39180
41154
39026
54011
41024
42844
37061
37062
39008
39009
37063
37064
39010
37130
41778
EF02-007
EF02-083
EF02-006
EF02-085
43768
37770RB
SC06-045*
37184
37185
39025
37182
37183
39024
42183*
42595
42291*
42468*
42469*
36210*
29523*
54003 *
Description
Gas Shock - 5 Pan (Before May 1, 1994)
Gas Shock - 3 Pan
Gas Shock - 5 Pan
Gas Shock Assy. - 7 Pan
Cutting Board - 3 Pan
Cutting Board (Poly) - 3 Pan
Cutting Board - 5 Pan
Cutting Board (Poly) - 5 Pan
Power Cord Assy. - 3 Pan
Power Cord Assy. - 5 Pan
Power Cord Assy. - 7 Pan
Clevis Pin
Cotter Pin
Lockwasher
Hinge Cap (Before May 1, 1994)
Hinge Cap
Hinge Block Assy. (Before May 1, 1994)
Hinge Block Assy.
Hinge Block Assy. - Center - 7 Pan
Hinge Pin
Hinge Pin - Center
Tape - Acrylic Foam
Crank (Before April 1, 1994)
Crank
Hinge Extrusion - 3 Pan
Hinge Extrusion - 5 Pan
Hinge Extrusion - 7 Pan - Right
Hinge Extrusion - 7 Pan - Left
Clamp Extrusion - 3 Pan
Clamp Extrusion - 5 Pan
Clamp Extrusion - 7 Pan
Pivot Support (Before May 1, 1994)
Pivot Support
Fuse - 15 Amp
Fuse - 20 Amp
Fuse Holder - 15 Amp
Fuse Holder - 20 Amp
Power Switch
PC Board - Output
Shoulder Screw
Lower Track - 3 Pan
Lower Track - 5 Pan
Lower Track - 7 Pan
Upper Track - 3 Pan
Upper Track - 5 Pan
Upper Track - 7 Pan
Air Deflector - 3 Pan
Air Deflector - 5 Pan - Alb.
Air Deflector - 5 Pan
Air Deflector - 7 Pan - Right
Air Deflector - 7 Pan Left
Replaceable Beeper
Probe
Legs
3
2
1
1
1
2
2
2
2
2
2
2
2
1
4
4
1
1
2
2
2
2
2
1
1
1
1
1
1
2
4
Qty. Per Unit
5
2
2
1
1
1
2
2
2
2
2
2
2
2
2
4
4
1
1
2
2
2
2
2
1
1
1
1
1
1
1
2
4
7
2
2
2
2
1
4
4
4
3
3
2
2
1
2
2
2
4
4
1
1
1
4
4
2
2
2
2
2
1
1
1
1
2
2
4
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HM-3/5/7
Service Parts List - Continued
Part
Number
41056
41055*
41057*
41162*
41163*
42661*
14151*
14155*
37159*
37371*
43568
43569
43666
43667
55870*
55871*
No.
61
61
61
62
62
62
63
63
64
65
67
67
67
67
68
69
Description
Seal - Canopy Glass - 3 Pan (Before May 1, 1994)
Seal - Canopy Glass - 5 Pan (Before May 1, 1994)
Seal - Canopy Glass - 7 Pan (Before May 1, 1994)
Seal - Side Glass - 3 Pan
Seal - Side Glass - 5/7 Pan
Seal - Side Glass - Alb.
Kit - Digital Display Uprights - O/S
Kit - Digital Display Uprights - 90°
Pan Support - Long
Pan - Cross Support
Upright Stud Assy. - Right - 90° w/probe guard
Upright Stud Assy. - Left - 90 ° w/probe guard
Upright Stud Assy. - Left - O/S w/probe guard
Upright Stud Assy. - Right - O/S w/probe guard
Right Water Pan Support Bracket
Left Water Pan Support Bracket
3
1
2
2
2
2
2
6
1
1
1
1
1
1
Qty. Per Unit
5
1
2
2
2
2
4
10
7
1
2
2
2
2
6
14
*not shown
HMT-3/5/7 Service Parts List
No.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
3
3
4
5
6
7
8
9
10
Part
Number
37000
54032
54128
54127
37001
54030
54035
54034
39027
54036
54037
54134
54135
54132
54133
38946
38915
45171
41028
37638
41507
40833*
42440*
39216
40097
28979
PLO 1-006*
18135
*not shown
Description
Front Viewing Glass - 3 Pan (Before July 1, 1994)
Front Viewing Glass Assy. - Complete - 3 Pan
Front Viewing Glass Assy. Complete - 3 Pan - Huss
Front Viewing Glass Assy. Complete - 3 Pan - Tyler
Front Viewing Glass Assy. - 5 Pan (Before July 1,1994)
Front Viewing Glass Assy. Complete - 5 Pan
Front Viewing Glass Assy. Complete - 5 Pan - Huss
Front Viewing Glass Assy. Complete - 5 Pan - Tyier
Front Viewing Glass Assy. - 7 Pan (Before July 1,1994)
Front Viewing Glass Assy. Complete - RH - 7 Pan
Front Viewing Glass Assy. Complete - LH - 7 Pan
Front Viewing Glass Assy. Complete - 7 Pan - Huss RH
Front Viewing Glass Assy. Complete - 7 Pan - Huss. LH
Front Viewing Glass Assy. Complete - 7 Pan - Tyier RH
Front Viewing Glass Assy. Complete - 7 Pan - Tyier LH
Sliding Door Assy. - 3 Pan
Sliding Door Assy. - 5 Pan
Sliding Door Assy. - HMT-5 (4 doors)
Sliding Door Assembly - 7 Pan
Water Pan Assembly (Before July 1, 1994)
Water Pan Assembly
Probe Bracket
Temperature Probe PC Board Assy.
Blower Motor
Series Regulating Thermostat
Transformer
Plug - Bottom
End Clamp
3
l
l
l
l
2
1
1
1
2
2
2
1
2
2
Qty Per Unit
5
l
1
1
1
2
4
1
1
1
2
2
2
1
2
2
**Front viewing glass before July 1, 1994, 02736 Tape Kit must also be ordered.
7
2
1
1
1
1
1
1
2
2
2
2
2
3
2
2
2
2
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HMT-3/5/7
Service Parts List - Continued
*not shown
No.
Part
Number
Description
Qty. Per Unit
3
5
7
11
12
13
14
15
16
17
17
18
18
18
18
18
18
18
18
18
19
20
21
21
22
22
23
23
24
24
25
25
26
26
26
26
26
27
28
29
30
31
31
31
32
33
33
33
33
33
34
34
34
34
34
34
35
35
35
36
37
38
MS01-162
22609
22610
ME50-003*
NS03-013*
EF02-040*
37230
49297
39938
42229
43791
42003
42230
43793
42009
42231
43792
39974
16685
37059
44976
37060
48020
39795
54041
BLO 1-009
BL01-015
54181
64257
41019
41020
41021
38413
49046
36900
37127
30723
52843
37420
37815
42341
16688
37128
41751
37129
41750
46502
43258
39181
43262
39840
49308
49309
37841
37849
41233
PN01-016*
PN01-017*
LW01-004*
Mounting Channel
Terminal Block
Barrier
Spacer
Cage Nut
Bushing - Snap
Bracket - Drop Shelf
Cutting Board Brace - KFC
Side Viewing Panel
Side Viewing Panel (Mir)-Left
Side Viewing Panel (Mir)-Right
Side Viewing Panel - Hussmann
Side Viewing Panel - Hussmann (Mir)-Left
Side Viewing Panel - Hussmann (Mir)-Right
Side Viewing Panel - Tyier
Side Viewing Panel - Tyier (Mir)-Left
Side Viewing Pane] - Tyier (Mir)-Right
Fan Blade
Fan Guard
Heater - Lower - 240 v
Heater - Lower - 208 v
Heater - Water - 240 v
Heater-Water-208 v
Socket - Light
Socket - Light - CE
Light Bulb- 120v- lOOw
Light Bulb - 240v - 60w
Heater - Upper Radiant - 240 v
Heater - Upper Radiant - 208 v
Decal - Control Panel - 3 Pan
Decal - Control Panel - 5 Pan
Decal - Control Panel - 7 Pan
Decal - Control Panel - 7 Pan - Left
Decal - Control Panel - KFC
PC Board Assembly - Control
Bracket for Plug
Relay
Probe - 5 ft.
Plug - Probe
Receptacle Assy. - Probe (Control Panel)
Receptacle Assy. - Probe (Uprights)
Cooling Fan
Gas Shock - 3 Pan (Before April 1, 1994)
Gas Shock-3 Pan
Gas Shock - 5 Pan (Before April 1, 1994)
Gas Shock-5 Pan
Gas Shock Assy. - HM-7
Cutting Board - 3 Pan
Cutting Board (Poly) - 3 Pan
Cutting Board - 5 Pan
Cutting Board (Poly) - 5 Pan
Cutting Board - KFC - HMT-3
Cutting Board - KFC - HMT-5
Power Cord Assy. - 3 Pan
Power Cord Assy. - 5 Pan
Power Cord Assy. - 7 Pan
Clevis Pin
Cotter Pin
Lockwasher
3
2
2
4
2
2
1
2
2
2
2
2
2
2
2
2
2
4
2
2
1
1
6
6
6
6
3
3
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
1
2
2
2
3
2
2
4
2
2
1
2
2
2
2
2
2
2
2
2
2
4
3
3
1
1
10
10
10
10
5
5
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
1
2
2
2
3
2
2
4
2
4
2
2
2
2
2
2
2
2
2
3
5
4
4
2
2
14
14
14
14
7
7
1
1
2
3
4
3
3
3
2
1
4
2
2
2
1
4
4
4
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HMT-3/5/7
Service Parts List - Continued
No.
Part
Number
Description
3
39
39
40
40
40
41
41
42
43
43
44
44
44
44
45
45
45
46
47
47
48
48
49
51
52
52
53
53
53
54
54
54
55
55
55
58
59
60
61
61
61
62
62
62
63
63
64
65
67
67
67
67
68
68
69
70
71
37044
41760
37231
42088
39180
41154
39026
54011
41024
41761
37061
37062
39008
39009
37063
37064
39010
37130
EF02-007
EF02-083
EF02-006
EF02-085
43768
37770
SC06-045*
SC06-060*
39961
39942
39025
37182
37183
39024
39978*
39977*
39979*
36210*
29523*
54003*
41056*
41055*
41057*
38932*
46624*
43549*
14122
14123
37159*
37371*
42333
42340
43562
43563
05835
05387
55870*
55871*
51530
Hinge Cap (Before April 1, 1994)
Hinge Cap
Hinge Block Assy. (Before April 1, 1994)
Hinge Block Assy.
Hinge Block Assy.- Center - 7 Pan
Hinge Pin
Hinge Pin - Center - 7 Pan
Tape - Acrylic Foam
Crank (Before April 1, 1994)
Crank
Hinge Extrusion - 3 Pan
Hinge Extrusion - 5 Pan
Hinge Extrusion -7 Pan - Right
Hinge Extrusion - 7 Pan-Left
Clamp Extrusion -3 Pan
Clamp Extrusion - 5 Pan
Clamp Extrusion - 7 Pan
Pivot Support
Fuse - 15 Amp
Fuse - 20 Amp
Fuse Holder - 15 Amp
Fuse Holder - 20 Amp
Power Switch
PC Board - Output
Shoulder Screw
Shoulder Screw - HMT-7
Lower Track - 3 Pan
Lower Track - 5 Pan
Lower Track - 7 Pan
Upper Track - 3 Pan
Upper Track - 5 Pan
Upper Track - 7 Pan
Air Deflector - 3 Pan
Air Deflector - 5 Pan
Air Deflector - 7 Pan
Replaceable Beeper
Probe
Legs
Seal - Canopy Glass - 3 Pan (Before April 1, 1994)
Seal - Canopy Glass - 5 Pan (Before April 1, 1994)
Seal - Canopy Glass - 7 Pan (Before April 1, 1994)
Seal - Side Glass
Seal - Side Glass - Huss.
Seal - Side Glass - Tyler
Kit - Digital Display Uprights - 90'
Kit - Digital Display Uprights - 0/S
Pan Support - Long
Pan - Cross Support
Upright Stud Assy. - Left - 90° - D/D - Probe Guard
Upright Stud Assy. - Rt. - 90° - D/D - Probe Guard
Upright Stud Assy. - Right - 0/S -D/D- Probe Guard
Upright Stud Assy. - Left - 0/S- D/D - Probe Guard
Bun Pan Insert - KFC - KMT-5
Bun Pan Insert - KFC - KMT-3
Right Water Pan Support Bracket
Left Water Pan Support Bracket
Contactor- 3 ph Albertsons
2
2
2
2
2
1
4
4
1
1
2
2
2
2
1
1
1
1
1
1
2
4
1
2
2
2
2
2
2
6
1
1
1
1
1
1
1
1
*not shown
Qty. Per Unit
5
7
2
2
2
2
2
2
4
4
1
1
2
2
2
2
1
1
1
1
1
1
2
4
1
2
2
2
2
2
4
10
1
1
1
1
1
1
1
1
3
3
2
2
1
2
2
2
4
4
1
1
1
4
2
2
2
2
1
1
1
1
2
2
4
1
2
2
2
2
2
6
14
1
1
1
1
1
1
1
Henny Penny
Service Parts List
No.
1
1
1
1
1
1A
1A
1
1
1
1
1
1A
1A
1
1
1
1
1
1
1A
1A
1
1
1A
1A
2
2
2
2
3
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18A
18
18
18
18A
18
18
18
18A
18
18
18
18A
18A
18
18
18
*not shown
Part
Number
37000
54109
54111
54105
54107
54110
54112
37001
54136
54138
54140
54142
54106
54108
54119
54117
54113
54115
54150
54146
54120
54118
54148
54144
54116
54114
37973
39114
38915
41028
37638
41507
40833*
42440*
39216
40097
28979
PL01-006*
18135
MS01-162
22609
22610
ME50-013
NS03-013
EF02-040
37230
38995
37757
42969
43794
38993
39938
42229
43791
42871
42230
43793
42003
42871
42872
42009
42231
43792
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 CM/CMT-5/7
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Description
Front Viewing Glass - CM/CMT-5 (before July 1, 1994)
Front Viewing Glass Assy. Complete. - CM-5 RH
Front Viewing Glass Assy. Complete - CM-5 LH
Front Viewing Glass Assy. Complete - CMT-5 RH
Front Viewing Glass Assy. Complete - CMT-5 LH
Glass-Canopy Guard - Assy. Complete - CM-5/7 RH
Glass-Canopy Guard - Assy. Complete - CM-5/7 LH
Front Viewing Glass - CM/CMT-7 (before July 1, 1994)
Front Viewing Glass Assy. - CM-7 RH
Front Viewing Glass Assy. - CM-7 LH
Front Viewing Glass Assy. - CMT-7 RH
Front Viewing Glass Assy. - CMT-7 LH
Glass Canopy Guard Complete - CMT-5/7 RH
Glass Canopy Guard Complete- CMT-5/7 LH
Front View Glass Assy. Complete - CMT-5-Huss. LH
Front View Glass Assy. Complete - CMT-5-Huss. RH
Front Viewing Glass Assy. Complete - CMT-5-Tyler RH
Front Viewing Glass Assy. Complete - CMT-5-Tyler LH
Front Viewing Glass Assy. Complete - CMT-7-Huss. RH
Front Viewing Glass Assy. Complete - CMT-7-Huss. LH
Glass Canopy Guard Assy. Complete - CMT-5/7-Huss. LH
Glass Canopy Guard Assy. Complete - CMT-5/7-Huss. RH
Front Viewing Glass Assy. Complete - CMT-7-Tyler RH
Front Viewing Glass Assy. Complete - CMT-7-Tyler LH
Glass Canopy Guard Assy. Complete - CMT-5/7-Tyler LH
Glass Canopy Guard Assy. Complete - CMT-5/7-Tyler RH
Sliding Door Assembly - CM-5
Sliding Door Assembly - CM-7
Sliding Door Assembly - CMT-5
Sliding Door Assembly - CMT-7
Water Pan Assembly (Before July 1, 1994)
Water Pan Assembly
Probe Bracket
Temperature Probe PCB Assembly
Blower Motor
Series Regulating Thermostat
Transformer
Plug-Bottom
End Clamp
Mounting Channel .292
Terminal Block
Barrier
Spacer
Cage Nut
Bushing- Snap
Bracket - Drop Shelf
Glass - Center Panel - CM-5/7
Side Viewing Panel - CM-5/7
Side Viewing Panel - Mir.-CM-5/7-Left
Side Viewing Panel - Mir.-CM-5/7-Right
Glass - Center Panel - CMT-5/7
Side Viewing Panel - CMT-5/7
Side Viewing Panel - Mir.-CMT-5/7-Left
Side Viewing Panel - Mir.-CMT-5/7-Right
Glass - Center Panel - CMT-5/7-Huss.
Side Viewing Panel - CMT-5/7-Mir.-Huss.-Left
Side Viewing Panel - CMT-5/7-Mir.-Huss.-Right
Side Viewing Panel - CMT-5/7-Huss.
Glass - Center Panel - CMT-5/7-Huss.
Glass - Center Panel - CMT-5/7-Tyler
Side Viewing Panel - CMT-5/7-Tyler
Side Viewing Panel - CMT-5/7-Mir.-Tyler-I.eft
Side Viewing Panel - CMT-5/7-Mir.-Tyler-Right
Qty. Per Unit
7
8
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
2
2
2
2
2
2
1
2
1
1
2
2
3
3
1
1
2
2
4
4
2
2
2
4
1
1
2
2
2
2
2
2
1
1
9
2
2
2
2
2
1
1
2
2
2
2
2
2
1
1
1
I
2
2
2
2
2
2
**Front Viewing Glass before July 1, 1994, 02736 Tape Kit must also be ordered.
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
CM/CMT-5/7 Service Parts List - Continued
No.
23
23
24
24
25
25
26
26
26
26
26
26
26
26
27
28
29
30
31
31
31
32
33
33
33
33
33
33
33
34
34
35
35
36
37
38
39
39
40
40
40
41
41
41
42
43
43
43
43
44
44A
44
44
44
44
45
45
Part
Number
39795
54041
BL01-009
BL01-015
54181
64257
41159
41160
41052
41053
48264
48263
41151
48265
36900
37420
30723 *
52843
37127
37815
42431
16688
37128
41751
37129
42925
42620
44608
48845
43258
43262
37849
39215
PN01-016*
PN01-107*
LW01-004*
37044
41760
37231
42088
39180
37026
41154
41154
54011
41024
42844
41024
41761
41217
41101
41102
41145
41008
41009
37063
37064
Description
Socket- Light
Socket- Light - CE
Light Bulb-120v-100w
Light Bulb - 240v - 60w
Heater - Upper Radiant - 240 v
Heater - Upper Radiant - 208 v
Decal - Control Panel - CM/CMT-7-Left
Decal - Control Panel - CM-7-Right
Decal - Control Panel - CM-5 - 0/S (single controls)
Decal - Control Panel - CMT-5 - 0/S (single controls)
Decal - Control Panel - CM-5 (dual controls)
Decal - Control Panel - CMT-5 (dual controls)
Decal - Control Panel - CMT-7-Right
Decal - Control Panel - Self Serve - CM/CMT-5
PC Board Assembly - Display
Plug for Probe
Relay
Probe- 5 ft.
Bracket for Plug
Receptacle Assy. - Probe - (Control Panel)
Receptacle Assy. - Probe - (Uprights)
Cooling Fan
Gas Shock - 3 Pan (Before April 1, 1994)
Gas Shock - 3 Pan
Gas Shock - 5 Pail (Before April 1,1994)
Gas Shock
Gas Shock Assy. (CM/CMT-5 & CM-7)
Gas Shock Assy. (CM/CMT-5 T&H only)
Gas Shock - CMT-7
Cutting Board - 3 Pan
Cutting Board - 5 Pan
Power Cord Assembly - 5 Pan
Power Cord Assembly - 7 Pan
Clevis Pin
Cotter Pin
Lockwasher
Hinge Cap (Before April 1, 1994)
Hinge Cap
Hinge Block Assy. (Before April 1, 1994)
Hinge Block Assembly
Hinge Block Assembly - Center - 7 Pan
Hinge Pin Center
Hinge Pin
Hinge Pin CM/CMT-7
Tape - Acrylic Foam
Crank - Steel - CM-5/7 (Before April 1, 1994)
Crank - Steel - CM-5/7
Crank - Steel - CMT-5/7 (Before April 1,1994)
Crank - Steel - CMT-5/7
Hinge Extrusion - LH - CM/CMT-7
Hinge Extrusion - RH - CM/CMT-5/7
Hinge Extrusion - RH - CM/CMT-5
Hinge Extrusion - RH - CM/CMT-7
Hinge Extrusion - LH - CM/CMT-5
Hinge Extrusion - LH - CM/CMT-5/7
Clamp Extrusion - CM/CMT-5
Clamp Extrusion - CM/CMT-7
*not shown
Qty. Per Unit
5
7
10
14
10
14
10
14
10
14
5
7
5
7
1
1
1
1
1
1
1
1
1
2
2
3
2
4
1
3
1
3
1
1
2
2
1
1
2
2
2
1
1
1
1
1
1
1
1
1
2
1
1
1
3
3
3
3
3
3
3
3
3
3
2
2
2
2
1
2
2
2
1
1
2
2
2
4
2
4
4
4
4
4
2
1
1
1
2
1
1
1
1
Henny Penny
CM/CMT-5/7 Service Parts List - Continued
No.
45
46
46
47
47
48
48
49
51
52
52
52
53
53
53
53
54
54
55
55
56
56
56
57
58
59
60
61
61
62
62
62
63
64
65
66
67
67
67
67
68
69
70
71
72
73
*not shown
C E Parts
46076
46209
48063
48064
48065
48066
48067
48068
48069
Part
Number
41010
37130
41778
EF02-006
EF02-085
EF02-007
EF02-083
43768
37770
SC06-045*
SC06-045*
SC06-060*
37185
39025
39942
39968
39024
37183
42824
42819
39797
49420
55406
41041
36210*
29523*
54003*
41055*
41056*
38932*
46624*
43549*
44489*
41413*
37159*
37371*
42333
42340
43562
43563
23560*
22046*
55804*
55870*
55871*
51530*
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Qty. Per Unit
Description
Clamp Extrusion - CM/CMT-5/7
Pivot Support (Before April 1, 1994)
Pivot Supports
Fuse Holder - 15 Amp
Fuse Holder - 20 Amp
Fuse - 15 Amp
Fuse - 20 Amp
Power Switch2
PC Board - Output
Shoulder Screw - CM-5/7
Shoulder Screw - CMT-5
Shoulder Screw - CMT-7
Lower Track - CM-5
Lower Track - CMT-7
Lower Track - CMT-5
Lower Track - CMT-7
Upper Track - CM/CMT-7
Upper Track - CM/CMT-5
Air Deflector - CM/CMT-7
Air Deflector - CM/CMT-5
Well Cover - 2"
Flat Well Cover
Well Cover- 3/8"
Viewing Window - CM/CMT-5/7
Replaceable Beeper
Probe - Temperature
Legs
Seal - Canopy Glass - 7 Pan (Before April 1, 1994)
Seal - Canopy Glass - 5 Pan (Before April 1, 1994)
Seal - Side Glass
Seal - Side Glass - Huss.
Seal - Side Glass - Tyler
Seal - Middle Glass
Viewing Window Bracket
Pan Support - Long
Pan - Cross Support
Upright Stud Assy. - Left - 90° - D/D - Probe Guard
Upright Stud Assy. - Rt. - 90°- D/D - Probe Guard
Upright Stud Assy. - Rt. - 0/S-D/D - Tall - Probe Guard
Upright Stud Assy. - Lt - 0/S-D/D - Tall - Probe Guard
Infinite Switch
Infinite Switch Knob
Power Cord Assy- 30A 3 Ph
Right Water Pan Support Bracket
Left Water Pan Support Bracket
Contactor- 3ph Albertsons
Lamp holder
Decal - Control Panel - HMT-5
Decal - Control Panel - HMT-3
Decal - Control Panel - HMT-3
Decal - Control Panel - HM-5
Decal - Control Panel - HM-7
Decal - Control Panel - HMT-7
Decal - Control Panel - CM-5
Decal - Control Panel - CMT-5
48070
48071
48072
48073
48074
48075
48078
48079
51058
51062
5
1
3
4
2
2
2
1
3
3
1
1
1
1
1
1
1
1
2
4
1
2
2
2
1
1
2
6
1
1
1
1
1
1
1
1
1
Decal - Control Panel - CM-7
Decal - Control Panel - CMT-7
Decal - Control Panel - HS-5
Decal - Control Panel - HST-5
Decal - Control Panel - HS-3
Decal - Control Panel - HST-3
Decal - Output Panel - HM 7
Decal - Output Panel - CM-7
Filter Board - HS/HST-3/5
Filter Board - HM/HMT/CM/CMT-3/5/7
7
1
4
2
2
2
2
2
1
1
1
1
1
1
1
1
1
2
2
4
1
2
2
2
1
1
4
10
1
1
1
1
1
1
1
1
1
1
Henny Penny
No.
1A
1A
1A
1A
1A
1A
1A
1A
2
2
2
9
10
11
12
13
14
15
16
17
18
18
18
18
18
18
18
18
18
18
18
18
21
21
23
23
24
24
25
25
26
26
26
26
29
33
33
33
34
34
34
34
35
35
35
35
Part
Number
54028
54125
54126
54038
54122
54123
54124
54121
38946
37972
37973
PL01-006*
18135
MS01-162
22609
22610
ME50-013
NS03-013
EF02-040
37230
37757
42969
43794
39938
42229
43791
42003
42230
43793
42009
42231
43792
37059
44976
39795
54041
BL01-009
BL01-015
54181
64257
39199
43017
41022
42245
30723
37128
42925
41751
43258
39181
43262
39840
43766
43767
37841
37849
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3 HS/HST-3/5 Service Parts List
Description
Canopy Guard Assy. Complete - HST-3
Canopy Guard Assy. Complete - HST-3-Tyler
Canopy Guard Assy. Complete - HST-3-Huss
Canopy Guard Assy. Complete - HST-5
Canopy Guard Assy. Complete - HST-5-Tyler
Canopy Guard Assy. Complete - HST-5-Huss
Canopy Guard Assy. Complete - HS-3
Canopy Guard Assy. Complete - HS-5
Sliding Door Assembly - HST-3
Sliding Door Assembly - HS-3
Sliding Door Assembly - HS-5
Plug - Bottom
End Clamp
Mounting Channel .292
Terminal Block
Barrier
Spacer .250 TH, .281 LG, .171 I.D.
Cage Nut
Bushing - Snap
Bracket - Drop Shelf
Side Viewing Panel - HS-3/5
Side Viewing Panel - HS-3/5 (Mir)-Left
Side Viewing Panel - HS-3/5 (Mir)-Right
Side Viewing Panel - HST-3/5
Side Viewing Panel - HST-3/5 (Mir)-Left
Side Viewing Panel - HST-3/5 (Mir)-Right
Side Viewing Panel - HST-5-Huss.
Side Viewing Panel - HST-5-Huss (Mir)-Left
Side Viewing Panel - HST-5-Huss (Mir)-Right
Side Viewing Panel - HST-5-Tyler
Side Viewing Panel - HST-5-Tyler (Mir)-Left
Side Viewing Panel - HST-5-Tyler (Mir)-Right
Heater - Lower - 240 v
Heater - Lower - 208 v
Socket - Light
Socket - Light - CE
Light Bulb-120 V-100 W
Light Bulb - 240 V - 60 W
Heater - Upper Radiant - 240 v
Heater - Upper Radiant - 208 v
Decal - Control Panel - HS-3
Decal - Control Panel - HS-5
Decal - Control Panel - HST-3
Decal - Control Panel - HST-5
Relay - HS/HST-5 only
Gas Shock (Before April 1,1994)
Gas Shock - HS/HST-3
Gas Shock - HS/HST-5
Cutting Board - 3 Pan
Cutting Board (Poly) - 3 Pan
Cutting Board - 5 Pan
Cutting Board (Poly) - 5 Pan
Wire Grid - HS/HST-3
Wire Grid - HS/HST-5
Power Cord Assembly - 3 Pan
Power Cord Assembly - 5 Pan
Qty. Per Unit
3
5
1
1
1
1
1
1
1
1
2
2
2
1
1
2
2
3
3
1
1
2
2
4
4
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
2
3
6
10
6
10
6
10
6
10
3
5
3
5
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
HS/HST-3/5 Service Parts List - Continued
No.
36
37
37
38
39
39
40
40
41
42
43
43
43
43
44A
44A
45
45
46
46
47
48
49
52
53
53
53
53
54
54
56
56
56
56
56
56
56
57
57
60
61
61
62
62
64
64
65
66
66
68
68
69
70
71
71
72
73
Part
Number
PNOl-016*
PN01-017*
PN01-017*
LW01-004*
37044
41760
37231
42088
41154
54011
41024
41024
42844
41761
37061
37062
37063
37064
37130
41778
EF02-007
EF02-006
43768
SC06-045
37184
37185
39961
39942
37182
37183
39185
42479
42477
42463
42413
46419
46420
39196
42253
54003*
41161*
41162*
41163*
41080*
41436*
42210*
41442*
42255*
41161*
37159*
37371 *
23560*
22045*
05863*
05864*
51058*
51530
Description
Clevis Pin
Cotter Pin - HS
Cotter Pin - HST
Lockwasher
Hinge Cap (Before April 1, 1994)
Hinge Cap
Hinge Block Assy. (Before April 1, 1994)
Hinge Block Assy.
Hinge Pin
Tape - Acrylic Foam
Crank-HS (Before May 1, 1994)
Crank-HST (Before April 1, 1994)
Crank-HS
Crank-HST
Hinge Extrusion - HS/HST-3
Hinge Extrusion - HS/HST-5
Clamp Extrusion - HS/HST-3
Clamp Extrusion - HS/HST-5
Pivot Support (Before May 1 1994)
Pivot Support
Fuse
Fuse Holder
Power Switch
Shoulder Screw
Lower Track - HS-3
Lower Track - HS-5
Lower Track - HST-3
Lower Track - HST-5
Upper Track - HS/HST-3
Upper Track - HS/HST-5
Well Cover - HS/HST-3 (Bun Pans)
Well Cover-3/8"- HS/HST-3
Well Cover-2". HS/HST-3
Well Cover-3/8"- HS/HST-5
Well Cover-2". HS/HST-5
Well Cover-Flat - HS-3
Well Cover-Flat - HS-5
Viewing Window - HS/HST-3
Viewing Window - HS/HST-5
Legs
Seal-Canopy Glass (Before April 1, 1994)
Seal- Side Glass - HS-3
Seal-Side Glass - HS-5
Seal-Side Glass - HST-3/5
Viewing Window Bracket - HS/HST-3
Viewing Window Bracket - HS/HST-5
Pan Insert Assy.-HS/HST - 3 (Before May 1, 1994)
Seal-Front Viewing Glass - HS/HST-5
Seal-Front Viewing Glass - HS/HST-3
Pan Support-Long
Pan-Cross Support
Infinite Switch
Infinite Switch Knob
Sneeze Guard - HST-3
Sneeze Guard - HST-5
Filter Board - CE
Contactor- 3ph Albertsons
*not shown
Qty. Per Unit
3
5
l
l
2
2
1
1
2
2
2
2
2
2
2
2
2
2
2
2
1
2
4
4
2
2
4
4
2
2
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
1
2
2
2
2
2
2
1
1
1
1
1
2
4
6
10
1
2
1
2
1
1
1
1
1
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
LIGHT CANOPY ASSEMBLY
Henny Penny
Model CM/CMT.5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT.5/7 HM/HMT-3/5/7 HS/HST-3
Henny Penny
Model CM/CMT-5/7 HM/HMT-3/5/7 HS/HST-3