Download Service Manual of Sony DSC-H1 Digital Camera

DSC-H1
SERVICE MANUAL
LEVEL
2
DSC-H1
Ver 1.0 2005. 04
US Model
Canadian Model
AEP Model
UK Model
E Model
Hong Kong Model
Australian Model
Chinese Model
Japanese Model
Korea Model
Tourist Model
Revision History
How to use
Acrobat Reader
Internal memory
ON BOARD
Link
SPECIFICATIONS
BLOCK DIAGRAMS
PRINTED WIRING BOARDS
SERVICE NOTE
FRAME SCHEMATIC DIAGRAMS
REPAIR PARTS LIST
DISASSEMBLY
SCHEMATIC DIAGRAMS
• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-880-51).
• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (9-876-880-41).
• Reference number search on printed wiring boards is available.
On the CH-169 and SY-127 board
This service manual provides the information that is premised the circuit board replacement service and not intended repair
inside the SY-127 board.
Therefore, schematic diagram, printed wiring board, mounted parts location and electrical parts list of the SY-127 board are not
shown.
The following pages are not shown.
Mounted parts location ............................. Page 4-64
Schematic diagram ............................. Pages 4-21 to 4-44
Electrical parts list ................................... Pages 5-14 to 5-18
Printed wiring board ............................ Pages 4-55 to 4-60
Waveforms ........................................... Page 4-62
DIGITAL STILL CAMERA
DSC-H1
9-876-880-31
Sony EMCS Co.
2005D1600-1
©2005.4
Published by DI Technical Support Section
SPECIFICATIONS
Camera
LCD panel
[System]
Image device
BC-CS2A/CS2B Ni-MH battery charger
[LCD screen]
7.19 mm (1/2.5 type) color
CCD, Primary color filter
6.2 cm (2.5 type) TFT drive
Total number of dots
115 200 (480x240) dots
Output voltage
Total pixel number of camera
Approx. 5 255 000 pixels
[Finder]
Effective pixel number of camera
Approx. 5 127 000 pixels
Total number of dots
115 200 (480x240) dots
Lens
[Power, general]
12 zoom lens
f = 6.0 - 72.0 mm (36 - 432 mm
when converted to a 35 mm still
camera)
F2.8 - 3.7
LCD panel
Power
Exposure control Automatic exposure, Shutter
speed priority, Aperture
priority, Manual exposure,
Scene Selection (7 modes)
White balance
Automatic, Daylight, Cloudy,
Fluorescent, Incandescent,
Flash, One push
File format (DCF compliant)
Still images: Exif Ver. 2.2
JPEG compliant, DPOF
compatible
Movies: MPEG1 compliant
(Monaural)
Recording media Internal memory 32 MB
“Memory Stick”
Flash
Viewfinder
Recommended distance (ISO
set to Auto): 0.3 m to 6.8 m
(11 26/32 inches to 22 feet
3 23/32 inches) (W)/0.9 m to
5.2 m (2 feet 11 14/32 inches to
17 feet 23/32 inches) (T)
[Input and Output connectors]
A/V OUT (MONO) jack (Monaural)
Minijack
Video: 1 Vp-p, 75 ,
unbalanced, sync negative
Audio: 327 mV (at a 47 k
load)
Output impedance 2.2 k
USB jack
0.75 cm (0.3 type) TFT drive
HR 15/51:HR6 (size AA)
Nickel-Metal Hydride batteries
(2), 2.4 V
ZR6 (size AA) Oxy Nickel
Primary Battery (2, not
supplied), 3 V
AC-LS5K AC Adaptor (not
supplied), 4.2 V
Power consumption
(during shooting with the LCD screen)
1.8 W
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
–20°C to +60°C (–4°F to
+140°F)
Dimensions
108x81.4x91.2 mm
(4 1/4x 31/4x 35/8 inches)
(W/H/D, excluding maximum
protrusions)
Mass
Approx. 590.8 g (1 lb 20.8 oz)
(including two batterries,
shoulder strap, adaptor ring,
lens hood, lens cap, etc.)
Microphone
Electret condenser microphone
Electric viewfinder (color)
Speaker
Dynamic speaker
Exif Print
Compatible
PRINT Image Matching III
Compatible
PictBridge
Power requirements
AC 100 to 240 V, 50/60 Hz,
3W
Compatible
mini-B
USB communication
Hi-Speed USB (USB 2.0
compliant)
DSC-H1
—2—
AA: DC 1.4V 400 mAx2
AAA: DC 1.4 V 160 mAx2
Operating temperature
0°C to +40°C (+32°F to
+104°F)
Storage temperature
–20°C to +60°C (–4°F to
+140°F)
Dimensions
Approx. 71x30x91 mm
(2 7/8x 13/16x 35/8 inches)
(W/H/D)
Mass
Approx. 90 g (3 oz)
Design and specifications are subject to change
without notice.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the B+ voltage to see it is at the values specified.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
DSC-H1
—3—
1.
TABLE OF CONTENTS
4-3. PRINTED WIRING BOARDS
SERVICE NOTE ........................................................ 1-1
2.
DISASSEMBLY
• CD-576 (CCD IMAGER)
PRINTED WIRING BOARD ······················· 4-49
• MS-275 (MEMORY STICK, LI BATTERY)
PRINTED WIRING BOARD ······················· 4-47
• ST-123 (FLASH DRIVE)
PRINTED WIRING BOARD ······················· 4-51
• ST-124 (FLASH)
PRINTED WIRING BOARD ······················· 4-52
• PL-039 (PLUNGER)
PRINTED WIRING BOARD ······················· 4-51
• SW-447 (FUNCTION SW, PITCH/YAW SENSOR AMP)
PRINTED WIRING BOARD ······················· 4-53
• EV-016 (EVF, BACK LIGHT)
PRINTED WIRING BOARD ······················· 4-49
• AF-102 FLEXIBLE (AF LED, LENS COVER SW)
PRINTED WIRING BOARD ······················· 4-47
2-1. DISASSEMBLY ······························································ 2-1
2-2. SERVICE POSITION ····················································· 2-5
2-3. CIRCUIT BOARDS LOCATION ··································· 2-7
2-4. FLEXIBLE BOARDS LOCATION ································ 2-8
HELP (List of caution points is shown here.)
3.
BLOCK DIAGRAMS
3-1.
3-2.
3-3.
3-4.
OVERALL BLOCK DIAGRAM (1/2) ··························· 3-1
OVERALL BLOCK DIAGRAM (2/2) ··························· 3-3
POWER BLOCK DIAGRAM (1/2) ································ 3-5
POWER BLOCK DIAGRAM (2/2) ································ 3-7
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM ································ 4-1
4-2. SCHEMATIC DIAGRAMS
• CD-576 (CCD IMAGER)
SCHEMATIC DIAGRAM ······························ 4-5
• MS-275 (MEMORY STICK, LI BATTERY)
SCHEMATIC DIAGRAM ······························ 4-7
• ST-123 (FLASH DRIVE)
SCHEMATIC DIAGRAM ······························ 4-9
• ST-124 (FLASH)
SCHEMATIC DIAGRAM ···························· 4-17
• PL-039 (PLUNGER)
SCHEMATIC DIAGRAM ······························ 4-8
• SW-447 (1/2) (FUNCTION SW)
SCHEMATIC DIAGRAM ···························· 4-11
• SW-447 (2/2) (PITCH/YAW SENSOR AMP)
SCHEMATIC DIAGRAM ···························· 4-13
• EV-016 (EVF, BACK LIGHT)
SCHEMATIC DIAGRAM ······························ 4-7
• AF-102 FLEXIBLE (AF LED, LENS COVER SW)
SCHEMATIC DIAGRAM ···························· 4-15
• SW-006 FLEXIBLE (SY-SW RELAY)
SCHEMATIC DIAGRAM ···························· 4-18
• MS-029 FLEXIBLE (SY-MS RELAY)
SCHEMATIC DIAGRAM ···························· 4-15
• ST-001 FLEXIBLE (SY-ST RELAY)
SCHEMATIC DIAGRAM ···························· 4-17
• FP-224 FLEXIBLE (SY-CD RELAY)
SCHEMATIC DIAGRAM ···························· 4-16
• CONTROL SWITCH BLOCK (SW51780)
SCHEMATIC DIAGRAM ···························· 4-19
Printed wiring board of the CH-169 and SY-127 board
are not shown.
Pages from 4-55 to 4-60 are not shown.
4-4. WAVEFORMS ······························································ 4-61
Waveforms of the SY-127 board are not shown.
Page 4-62 is not shown.
4-5. MOUNTED PARTS LOCATION ································· 4-63
Mounted parts location of the SY-127 board is not
shown.
Page 4-64 is not shown.
5.
REPAIR PARTS LIST
5-1. EXPLODED VIEWS ······················································ 5-3
5-1-1. OVERALL SECTION ···················································· 5-3
5-1-2. LED SECTION, CABINET(REAR) SECTION ············ 5-4
5-1-3. MAIN SECTION ··························································· 5-5
5-1-4. EVF SECTON ······························································· 5-6
5-1-5. LENS SECTION ··························································· 5-7
5-1-6. CABINET(FRONT) SECTION ····································· 5-8
5-1-7. ST SECTION ································································· 5-9
Checking supplied accessories ················································ 5-10
5-2. ELECTRICAL PARTS LIST ········································ 5-11
Shematic diagram of the CH-169 and SY-127 board
are not shown.
Pages from 4-21 to 4-44 are not shown.
DSC-H1
—4—
Electrical parts list of the SY-127 board are not
shown.
Pages from 5-14 to 5-18 are not shown.
1. SERVICE NOTE
• NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
When remove a connector, don't pull at wire of connector.
Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector.
Be in danger of the snapping of a wire.
Cut and remove the part of gilt
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
[Discharging of the FLASH unit’s charging capacitor]
1 kΩ/1 W
The charging capacitor of the FLASH unit is charged up to the
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-H1 is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Wrap insulating tape.
Preparing the Short Jig
To preparing the short jig. a small clip is attached to each end of a
resistor of 1 kΩ /1 W (1-215-869-11)
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
Discharging the Capacitor
1 Remove the main section.
2 Discharge the capacitor on the ST-123 board for about 10 seconds
by using the short jig.
Caution
1 Discharging the capacitor
Capacitor
Short jig (1kΩ/1W)
ST-123 board
DSC-H1
1-1
[Description on Self-diagnosis Display]
Self-diagnosis display
• C: ss: ss
The contents which can be handled
by customer, are displayed.
• E: ss: ss
The contents which can be handled
by engineer, are displayed.
Display Code
Countermeasure
Cause
Caution Display During Error
C:32:01
Turn off the main power then back on.
Trouble with hardware.
SYSTEM ERROR
C:13:01
Replace the memory stick.
Format the memory stick with the DSC-H1.
• The type of memory stick that cannot be
used by this machine, is inserted.
• Data is damaged.
• Unformatted memory stick is inserted.
MS ERROR
E:91:01
Checking of flash unit or replacement of
flash unit.
Abnormality when flash is being
charged.
Flash LED
Flash display
Flashing at 3.2 Hz
Checking of lens drive circuit
When failed in the focus initialization.
E:01:XX
E:61:00 *1
E:61:10 *1
Note : The error code is cleared if the battery is removed, except defective flash unit.
*1: The error display is given in two ways.
DSC-H1
1-2
—
• METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note: 1 When replacing the SY-127 board, erase the data in internal memory of the board before replacement.
Note: 2 When replacing the SY-127 board or the IC381 on the SY-127 board, execute formatting and initialize the internal memory after
replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a “Memory Stick”.
OK
See the following procedure.
Cancel
Cancels the copying.
1 Insert a “Memory Stick” having 32 MB or larger capacity.
2 Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appears.
3 Select [OK] with v , then press z.
Copying starts.
Copying
102_COPY
Use batteries with enough capacity or the AC Adaptor (not supplied). If you attempt to copy image files
using batteries with little remaining capacity, the batteries may run out, causing copying to fail or possibly
corrupting the data.
You cannot copy individual images.
The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick” after copying, then execute the [Format] command in
Internal Memory Tool.
You cannot select a folder copied on a “Memory Stick”.
The setting of
(Print order) marks is not copied even when you copy data.
Method for Formatting the Internal Memory
Format
Formats the internal memory.
Note that formatting irrevocably erases all data in the internal memory, including even protected images.
OK
See the following procedure.
Cancel
Cancels the formatting.
1 Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be erased Ready?” appears.
2 Select [OK] with v, then press z.
The format is complete.
• PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the
flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
Method for Initializing the Flash Error Code
Initialize
Initializes the setting to the default setting.
OK
See the following procedure.
Cancel
Cancels the resetting.
1 Select [OK] with v on the control button, then press z.
The message “Initialize all settings Ready?” appears.
2 Select [OK] with v, then press z.
The settings are reset to the default setting.
Make sure that the power is not disconnected during resetting.
DSC-H1
1-3E
2. DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
2
2
4
2
1
7
-12
SY
3
5
5
4
1 Three screws (M2x4) silver
3
2 Three screws (M2x4) silver
1
3 Remove the JK lid in the
4
1 Light guide plate (2.5) block
direction of the arrow.
3
4 Claw
2 Two claws
1 Tapping screw (M1.7x4) black
3 Remove the LCD, Light guide plate (2.5) block
1
5 Cabinet (rear) section
2 Three claws
in the direction of the arrow.
4 LCD unit
3 Claw
5 LCD unit, Light guide plate (2.5) block
4 LCD frame assembly
3
1
Note: Be very careful not to
damage the flexible board.
6
1 EV-016 board
2 Two claws
3 EVF section
5
7
-12
SY
9
2
3
4
3
7
2
Y-1
7
-44
SW
S
2
7
1
1
2
Y-1
2 Battery connector
4
S
2
3 From the loudspeaker
1 Flexible flat cable (SW-006)
2 Four tapping screws (M1.7x4) black
8
4 Three tapping screws (M1.7x4) black
3 Claw
6
5 Fuse replacement caution label
4 SW-447 board
7
-12
SY
6 SY-127 board
1 From the lens flexible board
5
3
7 6
2 FP-224 flexible board
3 From the lens flexible board
4
5
6
4 Flexible flat cable (ST-001)
5 Control switch block (SW51780)
6 AF-102 flexible board
1 Flexible flat cable (MS-029)
2 Tapping screw (M1.7x4) black
3 Two claws
SY-127
3
4
7 From the microphone
8 Tapping screw (M1.7x4) black
5
SY
-12
9 Main section
7
4 MS-275 board
1
2
3
7
5 Battery connector
4
6 Three claws
7 Battery terminal board
1
5
-27
MS
ST section
2
(See page 2-3.)
DSC-H1
2-1
2
1
7
1 Flexible flat cable (MS-029)
2-2
2. DISASSEMBLY
2
Caution
1 Discharging the capacitor
Capacitor
2
1
Short jig (1kΩ/1W)
1 Two tapping screws (M1.7x4) black
1
2 Lens section
ST-123 board
1 Tapping screw (M1.7x4) black
2 Control switch block (SW51780), Microphone unit
1
5
6
HELP 01
4
1 Tapping screw (M1.7x4) black
3
HELP 02
2 Claw
3 ST-123 board
3
4 Three harnesses (HA-001) (Red, White, Blue)
5 Open the ST cover in the direction of the arrow.
6 ST section
2
1
4
2
1 Remove the AF-102 flexible board
in the direction of the arrow.
2 Three claws
3 Three claws
4 AF-102 flexible board
DSC-H1
2-3
2-4
2-2. SERVICE POSITION
2
[SERVICE POSITION TO CHECK THE SY-127 BOARD]
1
From the lens section
SW-447 board
FP-224 flexible board
2
Flexible flat cable (SW-006)
2
SW
-44
4
Lens section
Monitor TV
7
5
3
1
1
Audio/Video jack
CN401
2
S
1
Y
-1
CN101
2
7
CN502
5
CN513
Caution
1 Discharging the capacitor
4
Capacitor
3
Short jig (1kΩ/1W)
From the lens section
Flexible flat cable (MS-029)
CN509
Battery terminal board
5
7
-2
S
M
ST-123 board
CN506
CN514
SY-127 board
MS-275 board
1
-12
SY
7
2
3
2
6
7
-12
SY
5
3
1
4
Battery section
4
3
1
Control switch block (SW51780)
Insert the batteries (size AA).
Nickel Metal Hydride batteries (x2).
3
-12
SY
7
-44
SW
7
7
-12
SY
2
1
2
4
6
MS-275 board
5
9
4
3
2
7
1
-12
SY
7
8
Flexible flat cable (MS-029)
DSC-H1
2-5
2-6
2. DISASSEMBLY
2-3. CIRCUIT BOARDS LOCATION
ST-123
AF-102
ST-124
MS-275
PL-039
CD-576
SW-447
CH-169
SY-127
EV-016
NAME
AF-102
CD-576
CH-169
EV-016
MS-275
PL-039
ST-123
ST-124
SW-447
SY-127
FUNCTION
AF LED, LENS COVER SW
CCD IMAGER
CCD SIGNAL PROCESS
EVF, BACK LIGHT
MEMORY STICK, LI BATTERY
PLUNGER
FLASH DRIVE
FLASH
FUNCTION SW, PITCH/YAW SENSOR AMP
LENS DRIVE, CAMERA A/D CONV., TIMING GENERATOR, CAMERA DSP,
SYSTEM CONTROL, 256Mbit SDRAM, FLASH MEMORY, SUPER AND FLASH MEMORY,
A/V AMP, USB/AV JACK, SP, MIC, PANEL DRIVE, STEADY SHOT CONTROL,
LENS SERVO, CONNECTOR, DC/DC CONVERTER
DSC-H1
2-7
2. DISASSEMBLY
2-4. FLEXIBLE BOARDS LOCATION
The flexible boards contained in the optical unit are not shown.
CONTROL SWITCH BLOCK (SW51780)
MS-029
SW-006
ST-001
FP-224
DSC-H1
2-8E
HELP
Disassembling and assembling procedures that require attention are described here.
HELP 01
Harness (HA-001) (Blue)
Harness (HA-001) (White)
Harness (HA-001) (Red)
HELP 02
6
7
1 Harness (H-001) (Red)
2White
2 Harness (H-001) (White)
8
3 Harness (H-001) (Blue)
4 Apply the soldering in three points.
5 ST-123 board
6 ST-124 board
7 Four claws
8 ST cover
1Red
9
3Blue
Blue
9 Tapping screw (M1.7x4) black
0 ST section
0
Red
4
White
5
DSC-H1
HELP
3. BLOCK DIAGRAMS
Link
DSC-H1
OVERALL BLOCK DIAGRAM (1/2)
POWER BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (2/2)
POWER BLOCK DIAGRAM (2/2)
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3-1. OVERALL BLOCK DIAGRAM (1/2)
LENS UNIT
FP-224 FLEXIBLE
BOARD
CD-576 BOARD
IRIS
SHUTER
IC101
CCD IMAGER
15
3
27,28
19-17
1-14
V1A,B
V2
V3A,B
V4
V5A,B
V6
V7A,B
V8,
DST,
VHLD
12
10
8
6
18
12
10
8
6
18
CN101
1
|
5
F2
E2
D2
B1
SHUTTER
MOTOR
M
SHUTTER +
SHUTTER-
8
5
9
M
ZOOM +
ZOOM -
36
M
IRIS DRIVE
D6
E6
B7
C6
16
ZOOM
MOTOR
(1/2)
F3
F4
FOCUS A
FOCUS XA
FOCUS B
FOCUS XB
FOCUS
MOTOR
IC401
F3
F4
39
F5
E5
D3
F1
SHUTTER DRIVE
G1
E4
FOCUS MOTOR
DRIVE
D5
A6
B6
C5
40 41
MSHUT DIR
MSHUT EN
D0-D31
IC353
256Mbit
SDRAM
22
ZOOM RESET
SENSOR 1ST
24
ZOOM RESET
SENSOR 2ND
25
D8,D7,E8
E7,D6,D5
E6,B4
B3,A3,B4
B5,A5,B6
A7,B7
LCD D0-D7
LCD HD
LCD VD
E9
B8
B9
A10
ZM DC FG 1A
ZM DC FG 1B
VR
VG
VB
IC602
U5
V4
EVF BL ON
EVF BL LEV
V5
W4
XSHIFT ON
7
PITCH
6
7
6
IC103
3
1
PITCH DRIVE
8
Y DRIVE A
Y DRIVE B
9
7
6
3
YAW DRIVE
7
(8/11)
1
IC901
3
SE402
YAW
SENSOR
12
IC401
PITCH/YAW
SENSOR
AMP
18
7
CN451
PITCH AD
YAW AD
4
8
IC381
IC351
SUPER AND
FLASH MEMORY
FLASH MEMORY
IC107
12
L26
A20,A21,A25
D0-D15
12
STEADY SHOT
CONTROL
AB13,AA13,AE13,AF13,AF12
AE12,AA12,AC12,AC11,AB12
AE11,AF11,AE10,AB11,AC10
AB10
D0-D15
AF21,AF20,AE20,AB18,AB19
AC19,AB16,AE19,AF19,AF18
AE18,AA15,AC18,AC17,AB15
AE17,AF17,AE16,AB14,AC16
AC15,AE14,
130
AUIN
184
V LINE OUT
EVF BL ON
EVF BL LEV
5
E6
IC801
MIC AMP
IC802
SPEAKER AMP
K26
AUOUT
E5
EV-016
FLEXIBLE
BOARD
15
|
5
1
1
ST 5V
EVF BL H
D001
(EVF BACK LIGHT)
2
CN510
2
B6
MIC SIG
MIC901
MIC
1
2
A5
A2
SP+
SP-
SP901
SPEAKER
D1
AU OUT AMP
C2
3,2
AC1
AD1
CN751
USB DPP, USB DMM
(USB)
USB VBUS
1
3
V OUT
U25
XAV JACK IN
V LINE OUT
H26
J751
A/V OUT
VIDEO AMP
AU LINE OUT
XDD RST OUT
SAN1 SO, SI, SCK
XSHIFT ON
SW-447 BOARD (1/2)
SW-006 FLEXIBLE
FLAT CABLE (1/2)
DSC-H1
3-1
20
CN511
T5
(6/11)
SAN1 SO, SI, SCK
63
F3
E3
C1
Q301
9
8
CN513
PITCH PWM
YAW PWM
66
65
37
38
129
14
95
96
7
21
|
17
14
|
10
6
21
19
(PAGE 3-4)
D0-D15
2
17
18
16
A01-A21
YAW PWM
4
EVF BACK LIGHT
DRIVE
PANEL REF
PANEL VST
VCK,EN
DWN,XSTB E
PCG,HST
HCK2,HCK1
RGT
EVF BL L
5
8
9
3
4
(6/11)
SAN1 SO, SCK
2
(9/11)
LPF
132
SE401
9
3
(9/11)
IC106
9
PITCH PWM
A01-A21,A25
YAW POS AD
2
7
131
X902
20MHz
8
6
LPF
8
CN101
PITCH
SENSOR
(9/11)
IC105
6
PITCH POS AD
4
7
PRE DRIVE
IC102
2
2
IC104
(9/11)
YAW
(9/11)
XDD RST OUT
USB VBUS
IC101
CN001
EVF COM/CS
Q602,603
TO
OVERALL
BLOCK DIAGRAM
(2/2)
XMS IN
(9/11)
P DRIVE A
P DRIVE B
CN508
(7/11)
(4/11)
LCD901
2.5 INCH
COLOR LCD
PANEL
22
|
19
14
|
11
8
|
6
2
PSIG
N6
N2
ZM DC FG 1A
ZM DC FG 1B
(5/11)
6
PANEL REF
PANEL VST
VCK,EN
DWN,XSTB M
PCG,HST
HCK2,HCK1
RGT
J7
31
(9/11)
24
23
PANEL COM/CS
C10
U4
ZM SENS 2ND
4
5
3
PSIG
PANEL REF
XSTB E
PANEL VST
VCK,EN
DWN,XSTB M
J4,H1 PCG,HST
H2,G1 HCK2,HCK1
G2,F1 RGT
F2,E2
D1,D2
C2,B1
L2
N5
L4
FC SENS
ZM SENS 1ST
ZM SENS 2ND
CN505
K4
A2
SAN1 SO, SCK
VR
VG
VB
R25
R5
FC DIR A
FC DIR B
FC EN
ZM SENS 1ST
J6
RGB DRVE
TIMING
GENERATOR
A9
C9
LCD CK
CN401
ACTIVE
LENS
ACTUATOR
K2
K3
K1
IC601
U2
T2 SAN1 SO, SI, SCK
R6
XSAN RST OUT
AF4
N4
P6
P4
R2
FC SENS
32
ZOOM DC FG
MS-275
BOARD
(1/2)
D9
MSHUT DIR
MSHUT EN
ZM DIR A
ZM BRK A
5
CAMERA DSP
D17,D18,D16,B18,A19
B19,E16,D19,E19,E17
B20,A20
A0-A11
ZM DIR A
ZM BRK A
FOCUS RESET
SENSOR
IC301
(1/2)
D21,D22,D20,B22,A22,A23
B23,E20,E21,B24,A24,A25
B25,C25,C26,B26,E10,A10
D10,E11,B10,A11,B11,E12
D11,D12,F12,B12,A12,E13
D13,D14
DIR2A
BRK2A
DIR2B
BRK2B
FC DIR A
FC DIR B
FC EN
A2
B2
ZOOM MOTOR
DRIVE
(4/11)
DIR2A
BRK2A
DIR2B
BRK2B
6
8
CN506
H5
J5
7
|
20
(1/11)
4
E1
CA HDCA FD
SAN1 SO,SCK
M
XMS IN
(7/11)
CN502
1
CLK TGO
47
45
46
25-38
IRIS
MOTOR
TIMING
GENERATOR
CN502
CN101
25-38
IRIS A
IRIS XA
IRIS B
IRIS XB
A6
4,3,5,7,2,8
CN251
7,8,6,
4,9,3
6,5,7,
9,4,10
MS D0-MS D3, MS BS, MS CLK
(3/11)
EXTAL
CP201
H1A,B
H2A,B
RG
AC4,AE4
AE5,AC5
AB6,AF6
X301
12MHz
XTAL OSC
(2/11)
BUFFER
K5,G4,H4,L5
H2,H1,J1,J2
M5,J4,K4,M6
K2,K1
CA AD0 - CA AD13
6
22
22
22
|
35
S/H
A/D CONV.
CCD OUT
IC102
1
MS-029 FLEXIBLE
BOARD (1/2)
SY-127 BOARD (1/2)
3-2
LCD902
COLOR EVF
UNIT
CN252
MEMORY
STICK
CONNECTOR
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3-2. OVERALL BLOCK DIAGRAM (2/2)
SY-127 BOARD (2/2)
ST-001
FLEXIBLE
FLAT CABLE
MS-275
BOARD
(2/2)
IC301
(2/2)
MS-029
FLEXIBLE
FLAT CABLE
(2/2)
CN251
FLASH UNIT
(ST-124
FLEXIBLE
BOARD)
ST UNREG
D001
(RECT)
T001
XE H
15
STRB CHG R22
4
9
10
XSTRB FULL V23
5
8
9
STRB CHG CONT AB22
6
7
6
STRB ON R4
6
7
HIGH VOLTAGE
CHAGER
C004
1
2
L001
TRIGGER
COIL
IC001
Q001
IGBT
DRIVE
4
CN501
CN506
VL 3V
2
BT251
BATTERY
(SECONDARY)
SYSTEM CONTROL
1
|
3
12
|
10
(3/11)
ST-123 BOARD
XE L
FLASH
DRIVE
7
D001
CN001
2
(1/11)
A1
STRB PLUNGER ON AA25
IC401
(2/2)
AF-102 FLEXIBLE BOARD
CN507
STRB PLUNGER
8
7
B3
RY301
PLUNGER
4
3
STRB PLUNGER DRIVE
XSTRB POPUP V22
XLENS COVER SENS AC23
1
4
BATTERY
TERMINAL
UNREG
2
1
REG GND
CN001
S001
(LENS COVER OPEN)
VL 3V
4
3
S301
(STRB POP UP)
1
5
XAF LED
D001 (AF LED)
PL-039 BOARD
ST UNREG
F001
CN514
SAN0 SO C5
SAN0 SI C6
XSAN0 SCK B6
CN509
SAN0 SO, SI, SCK
BATT SENS G5
XDD RST OUT
(11/11)
XPWR OFF
A7
UNREG
EVER 3.1V
EVER 2.8V
D 3.2V
D 3.2V (TO CAM)
DC/DC CONVERTER
REAL TIME CLOCK
F002
X001
32.768KHz
A8
OSC I
A9
OSC O
B8
D 3.2V (TO SP)
A 3.2V
MS VCC
CAM 2.9V (TO CAM)
CAM 2.9V (TO PANEL)
D 1.8V
VL 3V
C7
XPWR ON
C9
USB VBUS
SAN0 SO
SAN0 SI
XSAN0 SCK
XAE LOCK SW
XSHUTTER SW
K25
BATT SENS
MODE DIAL 0
MODE DIAL 1
Y4
R26
XDD RST OUT
A23
B7
IC001
AB5
AA5
Y5
XPWR OFF
SHUTTER
L22
L25
14
12
MODE DIAL
AB23
W22
10
9
G25
11
E22
1
D101 (FLASH)
D23
3
D102 (POWER)
S105
JOG A
JOG B
XSTRB LED
XPWR LED
EXEC
EVF/LCD, FOCUS, BRK
S104
4
XPWR ON
POWER
S107
1
BL H
BL L
XAF LED
JOG DIAL
S106,101,102
KEY AD2
PANEL 8.5V
A4
CONTROL SWITCH
BLOCK(SW51780)
8
7
M 5V
ST 5V
D 1.2V
B10 XMS IN
S103
N21
P23
TO
OVERALL
BLOCK DIAGRAM
(1/2)
XMS IN
(PAGE 3-2)
XDD RST OUT
XSHIFT ON
6
XSHIFT ON
STEADY SHOT
USB VBUS
DOWN, RIGHT, UP, LEFT, SET, DUST
S458,460,456,454,457,453
CN513
KEY AD0 K23
20
1
DOWN, RIGHT, UP, LEFT, SET, DUST
KEY AD1 L23
19
2
ZOOM WIDE, ZOOM TELE, MENU, DISPLAY
1
20
S459,455,452,451
(11/11)
IC005
CAM 15V
-7,5V/15V REG
CAM -7.5V
(11/11)
XACCESS LED E4
5
4
3
2
BL H
BL L
STEADY 5V
DC/DC CONV.
SW-006
FLEXIBLE
FLAT CABLE
(1/2)
16
17
18
19
6
4
CN452
SW-447 BOARD (2/2)
DSC-H1
3-3
LCD
BACK
LIGHT
D455 (ACCESS)
CN451
IC004
LED901
3-4
XENON
TUBE
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3-3. POWER BLOCK DIAGRAM (1/2)
4
3
BATTERY
TERMINAL
UNREG
ST-123 BOARD
ST-001
FLEXIBLE
FLAT CABLE
SY-127 BOARD (1/2)
F001
ST UNREG
IC004
4
9
10
XSTRB FULL
5
8
9
6
7
6
4
3
ST 5V
STEADY 5V
L010
2
MS VCC
9
15
L001
IC001
C004
1
2
HIGH VOLTAGE
CHAGER
IGBT DRIVE
FLASH UNIT
(ST-124
FLEXIBLE BOARD)
CN001
CN501
DC/DC CONV.
9
F002
STRB CHG
STRB CHG CONT
(11/11)
6
8
1
UNREG
MT 5V
(6/11)
(11/11)
MEMORY
STICK
CONNECTOR
9
CN251
MS VCC
EVER 3.1V
11
H1
R002
BT251
LITHIUM
BATTERY
(SECONDARY)
VL 3V
VL 3V
2
CN506
STRB CHG
XSTRB FULL
X001
32.768KHz
R22
(3/11)
V23
STRB CHG CONT
AB22
CAMERA DSP
SYSTEM CONTROL
R26
Y4
BATT SENS
B8 RTC BAT
MS PWR
A8 OSC I
LDO3IN
A9 OSC O
XDD RST OUT
XPWR OFF
A23
MS PWR ON
XCS DD
SAN0 SO
SAN0 SI
XSAN0 SCK
A7 XRESET
B7 XPWR OFF
MS PWR ON
D3
AA5
Y5
D23
D101 (FLASH)
1
E22
D 3.2V
UNREG2
A 3.2V
MS VCC
POWER
XPWR ON
CAM 2.9V
L803
VI 3.2V
D 1.8V
J6
K6
XPWR LED
XSTRB LED
LX5-1
LX5-2
LX5-3
LX5-4
K10
VO5
H10
(11/11)
L006
J9
J10
K9
7
Q004
SWITCHING & RECT
D003
(RECT)
15V REG
CAM 15V
6
IC005
VFB5 H9
-7.5V REG
L009
GT6 H6
3
CAM -7.5V
4
TO
POWER
BLOCK DIAGRAM
(2/2)
1
(PAGE 3-7)
1
-7.5V ON
VFB6 H7
M 5V
AU 3.2V
VI 3.2V
D 1.2V
PWR2
D10
L003
D 1.2V
LX2 C10
13
XPWR ON
4
C7 XPWRON1
LX3
D 3.2V
(5/11)
(4/11)
LV3
IC353
RS3
AF-102 FLEXIBLE
BOARD
D 1.8V
F9
L008
IC351
TG4
F10
3
BL L
BL L
Q003
SWITCH
M 5V
ST 5V
PANEL 8.5V
Q002
RECT
VFB4 F7
D3.2V
BL H
ST 5V
BG4 G9
FLASH MEMORY
BL H
F8
Q001
SWITCHING
(4/11)
D 1.2V
F003
D002
(RECT)
256Mbit
SDRAM
IC381
SUPER AND
FLASH MEMORY
STEADY 5V
L005
E10
VO3 E9
XAF LED
CAM 2.9V
PANEL 2.9V
B3
CN514
D001 (AF LED)
AU 3.2V
1
3.2V REG
B2
VFB2 D8
S104
IC803
4
3
G2
PWR56 OUT J7
K7
A 3.2V
MODE
DIAL
G1
A3
D 3.2V
2
A 3.2V
(6/11)
LDO2
P25
3
D 3.2V
1.8V REG
-7.5V ON
D102 (POWER)
L001
L011
A2
LDO2IN
A6
AB5
D 3.2V
A 3.2V
2.9V REG
G5 UNREGMON
XCS DD
C5 SAN0 SO
C6 SAN0 SI
B6 XSAN0 SCK
W23
MIC AMP
SPEAKER AMP
AU OUT AMP
D 3.2V (TO CAM)
VFB1 H2
MS PWR IN
LDO3
IC301
K25
T25
CONTROL SWITCH
BLOCK (SW51780)
3.1V
REG.
LDO1
D 3.2V (TO CAM)
VO1-1 F1
VO1-2 F2
J1 UNREG1-1,2
K1
D001
D 3.2V (TO SP)
PWR1-1 A1
PWR1-2 B1
PWR1-3 C2
DC/DC CONVERTER
REAL TIME CLOCK
EVER 2.8V
IC801
AU 3.2V
IC001
MS-275
BOARD
CN252
D001
(RECT)
XE H
1
|
3
ST UNREG
2 REG GND
1
CN509
T001
12
|
10
CAM 2.9V (TO PANEL)
PSG4 G8
A4
4
XAF LED
CN507
VO7 K4
PANEL 8.5V
(6/11)
IC802
CAM 3.2V
D821
-7.5V ON
D 3.2V
A 3.2V, AU 3.2V, VI 3.2V, D 1.8V, D 1.2V
DSC-H1
3-5
3-6
VIDEO AMP
XENON
TUBE
3-4. POWER BLOCK DIAGRAM (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-127 BOARD (2/2)
CP201
D 3.2V
CD-576 BOARD
FP-224
FLEXIBLE
BOARD
(2/11)
D 3.2V
S/H
A/D CONV.
TIMING GENERATOR
A 3.2V
CAM 2.9V
IC102
BUFFER
L201
CAM 15V
16
16
IC101
14
14
CCD IMAGER
CAM 15V CD
CAM -7.5V
CAM -7.5V
CN101
CN502
D 3.2V
(1/11)
21
FC RST VCC
FOCUS
RESET
SENSOR
ZM RST VCC
ZOOM
RESET
SENSOR
IC401
M 5V
IRIS DRIVE
SHUTTER DRIVE
FOCUS MOTOR DRIVE
ZOOM MOTOR DRIVE
PLUNGER DRIVE
(9/11)
IC110
STEADY 5V
27
28
Q107,110
CURRENT
LIMITER
ZM FG VCC
VCC
33
TO
POWER
BLOCK DIAGRAM
(1/2)
ZOOM
DC FG
CN401
FULL PWR
LIM PWR
1
LENS UNIT
(9/11)
(9/11)
(9/11)
IC101
IC107
IC105
IC106
IC104
INVERTER
LPF
(9/11)
IC102
IC103
PRE DRIVE
L101
ACTIVE
LENS
ACTUATOR
A 4.6V
3
PITCH DRIVE
YAW DRIVE
CN101
(9/11)
IC108
(PAGE 3-6)
3
A 4.6V
1
4.6V REG
L103
SW-006
FLEXIBLE
FLAT CABLE
4
SW-447
BOARD
IC401
PITCH/YAW
SENSOR AMP
XFE ON / VAP DD ON
XFE ON / VAP DD ON
10
A 3.2V
9
11
A 3.2V
8
D 3.2V
18
D 3.2V
BL H
5
BL H
BL L
4
3
2
BL L
CN513
Q401,402
12
13
D455
3
ACCESS LED
16
17
18
19 CN451
CN452
4
FULL PWR
LIM PWR
154
155
(8/11)
IC901
XFE ON / VAP DD ON
170
PANEL VDD
18
STEADY SHOT
CONTROL
D_1.2V
(7/11)
79
37
36
38
IC601
EVF BL ON
EVF BL LEV
LCD901
2.5 INCH
COLOR LCD
PANEL
LED901
LCD
BACK
LIGHT
CN505
(7/11)
RGB DRIVE
TIMING
GENERATOR
IC602
EVF BL ON
EVF BL LEV
BACK LIGHT
DRIVE
Q602, 603
EVF BL L
ST 5V
L603
EVF BL H
PANEL 8.5V
L602
PANEL VDD
D001 (EVF BACK LIGHT)
1
CN001
2
16
2
CAM_ 2.9V(TO PANEL)
CN508
EV-016
FLEXIBLE BOARD
DSC-H1
3-7
6
3-8E
LCD902
COLOR EVF
UNIT
SE401, 402
PITCH/YAW
SENSOR
N
4-1
LENS UNIT
CD-576 BOARD
CN101
A_4.6V
Y_OUT
REG_GND
P_DRIV_B
P_DRIV_A
3
4
5
6
7
39P
N.C.
CN507 10P
EV-016 FLEXIBLE BOARD
EVF,BACK LIGHT
F
G
USB
20P
SY-127 BOARD
(1/11) LENS DRIVE
(2/11) CAMERA A/D CONV. TIMING GENERATOR
(3/11) CAMERA DSP,SYSTEM CONTROL
CN505 24P
(9/11) LENS SERVO
(10/11) CONNECTOR
(11/11) DC/DC CONVERTER
(CH-169 board) CCD SIGNAL PROCESS
CN101 10P
7
6
5
4
3
2
1
REG_GND
XSTRB_POPUP
XAF_LED
D_3.2V
REG_GND
XLENS_COVER_SENSE
3
2
1
UNREG
REG_GND
REG_GND
4
8
STRB_PLUNGER
UNREG
9
REG_GND
STRB_PLUNGER
10
1
MIC_GND
REG_GND
2
MIC_SIG
BL_H
BL_L
BL_L
XACCESS_LED
18
19
20
STRB_PLUNGER
REG_GND
XSTRB_POPUP
1
STRB_PLUNGER
2
REG_GND
4
3
REG_GND
5
CN451 20P
6
17
CN509 4P
MODE_DIAL0
A_3.2V
13
MODE_DIAL1
14
12
KEY_AD2
11
JOG_A
10
JOG_B
9
XAE_LOCK_SW
8
XSHUTTER_SW
7
XSHIFT_ON
REG_GND
5
XPWR_ON
6
4
XPWR_LED
3
D_3.2V
2
XSTRB_LED
1
MS_D3
REG_GND
VL_3V
9
XMS_IN
8
MS_D2
7
MS_D0
6
MS_D1
5
MS_BS
4
REG_GND
3
2
ST_5V
9
REG_GND
8
STRB_ON
7
STRB_CHG_CONT
6
XSTRB_FULL
5
STRB_CHG
4
REG_GND
3
REG_GND
REG_GND
ST_UNREG
12
1
ST_UNREG
ST_UNREG
11
2
ST_UNREG
ST_UNREG
10
3
ST_UNREG
4
ST_5V
5
REG_GND
6
STRB_ON
7
STRB_CHG_CONT
9
STRB_CHG
10
8
XSTRB_FULL
REG_GND
2
11
REG_GND
1
12
REG_GND
DSC-H1
4-2
SY-ST RELAY
20
KEY_AD0
BL_H
17
16
MS-029
FLEXIBLE
FLAT CABLE
19
KEY_AD1
REG_GND
16
15
ST-001
FLEXIBLE
FLAT CABLE
18
D_3.2V
CN510 2P
Y_DRIV_B
17
REG_GND
SY-SW RELAY
9
16
VST_C_RESET
A_3.2V
REG_GND
15
LENS COVER SW
10
15
REG_GND
A_3.2V
14
13
REG_GND
8
12
YAW_AD
7
PITCH_AD
REG_GND
6
VAP_DD_ON
VST_C_RESET
5
11
REG_GND
4
REG_GND
D_3.2V
3
10
KEY_AD1
2
9
KEY_AD0
1
14
Y_DRIV_A
P_OUT
2
14
YAW_AD
1
13
8
LENS_VC
1
V3B
V7A
REG_GND
34
33
V3A
V4
33
V7A
32
V6
V8
32
V3A
31
V2
VHLD
V1B
39
31
V6
30
V5B
39
30
V2
29
V1A
REG_GND
29
VHLD
28
V5A
VST
28
V1B
27
REG_GND
38
27
V5B
26
REG_GND
37
26
V1A
25
CCD_OUT
REG_GND
REG_GND
36
25
V5A
24
23
22
38
24
REG_GND
FP-224 FLEXIBLE BOARD
37
23
REG_GND
SY-CD RELAY
36
22
CCD_OUT
REG_GND
CN502
21
13
REG_GND
E
V4
21
REG_GND
RG
CN401 39P
20
12
PITCH_AD
SW-006
FLEXIBLE FLAT CABLE
V8
20
REG_GND
REG_GND
2.5 INCH
LCD UNIT
19
11
REG_GND
2
N.C.
PLUNGER
VST
19
REG_GND
CAM_15V_CD
LCD BACK LIGHT
18
POWER_SAVE
10
VAP_DD_ON
3
VDD
(1/2) FUNCTION SWITCH
(2/2) PITCH/YAW SENSOR AMP
V7B
18
RG
17
16
15
9
A_3.2V
4
REG_GND
SW-447 BOARD
35
17
REG_GND
8
A_3.2V
5
EVF_VSSG
CN452 6P
34
16
CAM_15V_CD
7
REG_GND
6
HST
A
35
15
POWER_SAVE
CAM_-7.5V_CD
REG_GND
14
13
6
REG_GND
7
HCK2
12
V7B
14
H1A
REG_GND
12
11
5
BL_H
8
HCK1
11
V3B
13
L
REG_GND
12
H1A
H1B
8
H2A
REG_GND
7
REG_GND
H2B
6
9
REG_GND
5
10
RAMDOM_TRIGGER
4
4
BL_H
9
RGT
10
CAM_-7.5V_CD
11
REG_GND
8
H1B
9
7
REG_GND
10
6
3
CN513
H2A
5
VSUB
2
3
BL_L
10
DWN
9
REG_GND
4
H2B
CSUB
1
CN508 22P
REG_GND
REG_GND
2
BL_L
CN001 21P
RAMDOM_TRIGGER
ZM_DC_MOTOR_-
39
1
XACCESS_LED
11
REF
COLOR EVF UNIT
3
ZM_DC_MOTOR_-
SPEAKER
38
22
REG_GND
12
XSTB
BL_H
XZM_FG_TR
21
HST
13
VST
N.C.
6
ZM_DC_MOTOR_+
20
HCK1
14
VCK
BL_L
5
ZM_DC_MOTOR_+
19
DWN
15
EN
4
37
34
18
XSTB_E
16
PCG
N.C.
36
XZM_FG_LED
33
17
VCK
17
B
3
35
ZM_DC_FG_1A
ZM_FG_VCC
32
16
PANEL_VDD
18
R
N.C.
2
ZM_RST_VCC2
28
15
EVF_VSSG
19
G
N.C.
2
VSUB
ZM_RST_VCC1
27
24
23
22
21
14
20
CS
B
1
CSUB
XZM_RST_LED1
26
COM
CS
VST
VCK
20
13
12
RGT
11
VST
PANEL_REF
HCK2
9
10
8
VG
EN
7
VB
6
PCG
5
PSIG
4
CS
VR
21
COM
PSIG
8
1
ZM_SENS_2ND
25
XZM_RST_LED2
ZM_SENS_1ST
24
ZM_DC_FG_1B
XZM_RST_TR1
23
XZM_RST_TR2
FC_SENS
22
31
FC_RST_VCC
21
EN
19
18
17
16
15
14
13
12
11
3
7
REG_GND
M
30
XFC_RST_TR
20
DWN
PANEL_VDD
REG_GND
N.C.
PANEL_VSSG
XSTB_M
PCG
HST
2
COM
6
29
XFC_RST_LED
CN511 2P
19
LENS_TMP
FOCUS_XA
15
18
FOCUS_B
14
FOCUS_XA
FOCUS_B
13
J
PANEL_REF
1
EVF_BL_L
EVF_BL_H
AV
REG_GND
FOCUS_A
12
10
9
8
7
6
5
C
17
FOCUS_A
11
TEST1
N.C.
HCK2
HCK1
4
5
16
FOCUS_XB
SHUTTER_+
8
FOCUS_XB
SHUTTER_+
7
PSIG
3
2
1
D
9
SHUTTER_-
6
VG
VR
VB
RGT
TEST2
4
10
SHUTTER_-
5
SP_+
IRIS_XA
1
4
SP_-
IRIS_XB
2
IRIS_A
K
IRIS_B
I
3
3
H
2
2
1
1
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
18
19
REG_GND
12
1
REG_GND
MS_VCC
CN506 12P
11
2
MS_VCC
MS_CLK
10
3
MS_CLK
1
CN501 12P
4
MS_D3
5
XMS_IN
6
MS_D2
7
MS_D0
8
MS_D1
9
MS_BS
10
REG_GND
11
VL_3V
12
REG_GND
20
21
MS-275
BOARD
MEMORY STICK,
LI BATTERY
(LITHIUM BATTERY)
(SECONDARY)
22
PL-039 BOARD
CN301 6P
AF
BATTERY
AF-102 FLEXIBLE BOARD
AF LED,LENS COVER SW
MIC
CN514 14P
CONTROL SWITCH BLOCK
(SW51780)
CN251 12P
VSS
1
MS_BS
10P
2
DATA1
3
SDIO/DATA0
4
DATA2
5
INT
6
DATA3
SCLK
VCC
7
9
VSS
10
MEMORY
STICK
CONNECTOR
CN252
8
(4/11) 256Mbit SDRAM,FLASH MEMORY
(5/11) SUPER AND FLASH MEMORY
(6/11) A/V AND,USB/AV JACK,SP,MIC
(7/11) PANEL DRIVE
(8/11) STEADY SHOT CONTROL
CN001 12P
ST-124
FLEXIBLE BOARD
FLASH
FLASH DRIVE
ST-123 BOARD
39P
CCD IMAGER
CCD IMAGER
16
FRAME SCHEMATIC DIAGRAM
4-2. SCHEMATIC DIAGRAMS
Link
CD-576 BOARD (CCD IMAGER)
EV-016 FLEXIBLE BOARD (EVF, BACK LIGHT)
MS-275 BOARD (MEMORY STICK, LI BATTERY)
AF-102 FLEXIBLE BOARD
ST-123 BOARD (FLASH DRIVE)
SW-006 FLEXIBLE BOARD (SY-SW RELAY)
ST-124 FLEXIBLE BOARD (FLASH)
MS-029 FLEXIBLE BOARD (SY-MS RELAY)
PL-039 BOARD (PLUNGER)
ST-001 FLEXIBLE BOARD (SY-ST RELAY)
SW-447 BOARD (1/2) (FUNCTION SW)
FP-224 FLEXIBLE BOARD (SY-CD RELAY)
SW-447 BOARD (2/2)
(PITCH/YAW SENSOR AMP)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-H1
(AF LED, LENS COVER SW)
CONTROL SWITCH BLOCK (SW51780)
WAVEFORMS
4-2. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
Link
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
1. Connection
Pattern box
Color bar chart
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-1450:
J-6082-559-A
Pattern box
Kinds of capacitor
100 cm (PTB-450)
40 cm (PTB-1450)
Temperature characteristics
External dimensions (mm)
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with * differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT → EDIT
PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line
• J : IN/OUT direction of (+,–) B LINE.
• C: adjustment for repair.
• A: VIDEO SIGNAL (ANALOG)
• A: AUDIO SIGNAL (ANALOG)
• A: VIDEO/AUDIO SIGNAL (ANALOG)
• A: VIDEO/AUDIO/SERVO SIGNAL
• A: SERVO SIGNAL
• Circled numbers refer to waveforms.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Front of the lens
A B
Red
Blue
White
Magenta
H
Cyan
Green
Yellow
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
A=B
B A
Fig. a (Video output terminal output waveform)
Electronic beam
scanning frame
CRT picture frame
Fig.b (Picture on monitor TV)
Precautions Upon Replacing CCD imager
• The CD-576 board mounted as a repair part is not equipped
with a CCD imager.
When replacing this board, remove the CCD imager from
the old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the
adjustments for the camera section.
• As the CCD imager may be damaged by static electricity
from its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
When indicating parts by reference number, please
include the board name.
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
DSC-H1
4-3
Note :
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
For Schematic Diagram
• Refer to page 4-49 for printed wiring board.
4-2. SCHEMATIC DIAGRAMS
3
2
1
• Refer to page 4-61 for waveforms
4
5
6
7
CD-576 BOARD
A
9
8
V1A
V1B
CCD IMAGER
V2
XX MARK:NO MOUNT
V3A
V3B
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
VST
1
V4
V5A
CN101 39P
25
V5A
REG_GND
24
REG_GND
23
CCD_OUT
22
REG_GND
21
REG_GND
20
REG_GND
19
RG
18
REG_GND
17
CAM_15V_CD
16
POWER_SAVE
15
F
13
H1A
12
REG_GND
11
H2A
10
REG_GND
9
H1B
8
REG_GND
7
H2B
6
REG_GND
5
RAMDOM_TRIGGER
4
VSUB
3
CSUB
2
REG_GND
1
VHLD
V5B
R-6.6/P0
V8
R-6.5/P0
V7B
R-6.5/P0
V7A
R11.7/P0
CCD_OUT
R15.1/P0
VDD
2
7
6
GND
VCC
OUT
IDRV
R15.1
P0
R4.1
P0
C101
0.01u
1
R108
0
2
Q104
DTC144EMT2L
VSUB
1
R109
270k
0
R104
1500
0
R106
220k
R2.9
P0
C103
XX
R3.5
P0
2
Q102
3
DTC144EMT2L
SWITCH
R105
1200
7
CL124
R-7.6
P0
R2.0
P0.1
R1.2
P0.1
R11.0
P0
R11.3
P0
CL123
R13.3
P0.3
R2.0
P0.1
R1.2
P0.1
R11.7
P0
ISF
IN
C102
0.1u
16V B
6
R11.7
P0
IC101
ICX495BQF
15 16 17 18 19 20 21 22 23 24 25 26 27 28
IC102
CXA3691EN-T9
14
REG_GND
5
BUFFER
3
C109 0.1u 16V B
CAM_-7.5V_CD
IC102
CL101
V5A
CCD IMAGER
Note
V1A
V1A
1
V1B
26
2
H2A
V1A
IC101
3
H1A
V5B
CL104
27
4
V2
V5B
5
VL
V1B
V1B
6
V3A
VHLD
28
7
N.C.
29
Note:IC101 is not included in this
complete board of CD-576 board.
8
V3B
VHLD
9
CSUB
V2
14 13 12 11 10
VST
30
4
SUB
31
V2
CL108
V6
V6
V4
V3A
GND
32
CL109
33
V3A
V5A
V7A
GND
V8
V7A
GND
V3B
H2B
34
CL113
V7B
1
R-0.3
P0
R-7.3
P0
R-0.3
P0
R-0.3
P0
R-0.3
P0
R-6.2
P0
R-0.4
P0
R-0.4
P0
R-0.3
P0
R-0.5
P0
R-0.5
P0
V3B
V7B
V6
35
V7A
H1B
V7B
VST
C105 0.1u 16V B
E
36
5
(PAGE 4-16)
VST
V6
4
TO
FP-224
FLEXIBLE BOARD
37
1
D
V8
VHLD
V8
2
C
38
RG
V4
V4
3
B
V5B
39
C107
0.1u
REG_GND
C108
XX
R110
1M
3
G
16
DSC-H1
4-5
4-6
CD-576
For Schematic Diagram
• Refer to page 4-49 for printed wiring board.
For Schematic Diagram
• Refer to page 4-51 for printed wiring board.
2
1
3
EV-016 FLEXIBLE BOARD
EVF,BACK LIGHT
22P
1
EVF_BL_H
2
COM
3
CS
4
VR
5
PCG
6
PSIG
7
LND002
A
6
2
1
D001
NSCW455T-TC9
(EVF BACK LIGHT)
LND001
EVF_BL_L
5
4
CN001 21P
LND003
21
COM
20
PSIG
19
CS
18
G
17
R
16
B
15
PCG
14
EN
13
VCK
12
VST
11
XSTB
PL-039 BOARD
LND004
LND005
A
LND006
PLUNGER
XX MARK:NO MOUNT
CN301 6P
LND007
LND008
8
VG
TO
AF-102
FLEXIBLE BOARD
LND009
VB
9
EN
10
VST
11
PANEL_REF
12
LND010
B
TO
SY-127 BOARD(7/11)
CN508
(PAGE 4-15)
LCD902
COLOR EVF
UNIT
LND011
LND012
(PAGE 4-34 OF LEVEL3)
LND013
RGT
13
B
LND014
HCK2
14
EVF_VSSG
15
10
REF
9
DWN
8
RGT
7
HCK1
6
HCK2
5
HST
4
EVF_VSSG
3
REG_GND
2
VDD
1
N.C.
REG_GND
6
REG_GND
5
STRB_PLUNGER
4
STRB_PLUNGER
3
REG_GND
2
XSTRB_POPUP
1
16
17
D302
1SS355TE-17
2
RY301
(PLUNGER)
1
S301
(FLASH POP UP)
LND301
STATIC_GND
LND016
VCK
C301
1u
D301
XX
LND015
PANEL_VDD
4
3
16
LND017
LND018
C
XSTB_E
18
DWN
19
HCK1
20
HST
21
REG_GND
22
LND019
LND020
LND021
16
LND022
For Schematic Diagram
• Refer to page 4-47 for printed wiring board.
1
2
3
4
5
6
MS-275 BOARD
MEMORY STICK,LI BATTERY
A
XX MARK:NO MOUNT
CN251 12P
REG_GND
B
12
VL_3V
11
REG_GND
10
MS_BS
9
TO
MS-029
FLEXIBLE FLAT CABLE
MS_D1
8
MS_D0
7
(PAGE 4-15)
MS_D2
6
XMS_IN
5
MS_D3
4
MS_CLK
BT251
(LITHIUM BATTERY)
(SECONDARY)
10P
1
VSS
2
MS_BS
3
DATA1
4
SDIO
5
DATA2
6
INT
7
DATA3
3
8
SCLK
MS_VCC
2
9
VCC
REG_GND
1
10
VSS
CL251
CL257
FB251
0uH
FB252
0uH
FB253
0uH
FB254
0uH
R253
1k
CL256
R251
0
C251
XX
CL262
C252
0.1u
B
C
LND251
STATIC_GND
16
D251
XX
CN252
MEMORY
STICK
CONNECTOR
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Note :
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
DSC-H1
4-7
4-8
EV-016/MS-275/PL-039
For Schematic Diagram
• Refer to page 4-51 for printed wiring board.
1
ST-123 BOARD
FLASH DRIVE
A
2
4
3
5
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
ST_UNREG
1
ST_UNREG
2
ST_UNREG
3
ST_5V
4
REG_GND
5
STRB_ON
6
STRB_CHG_CONT
7
XSTRB_FULL
8
STRB_CHG
9
REG_GND
10
REG_GND
11
REG_GND
12
9
8
10
T001
CONVERTER
TRANSFORMER
XX MARK:NO MOUNT
CN001 12P
7
6
L001
4.7uH
D001
FT02P80TP
C001
22u
6.3V
LND003
6
2
C005
22u
6.3V
XE_H
1
TO
ST-001
FLEXIBLE FLAT CABLE
B
(PAGE 4-17)
4
3
5
C004
205u
330V
3.1
TO
ST-124 BOARD
C
(PAGE 4-17)
N.C
XFULL
7
6
0
5
REG_GND
3.2
5
N.C
G_IGBT
F_ON
10 11 12
CHG
LND004
0
9
VCC
IC001
TPS65552RGTR
8
0
4
C002
1u
C
PGND
SW
I_PEAK
0
D
PGND
SW
N.C
3
5.1
R004
XX
N.C
3.1
1
2
R001
0
N.C
IC001
HIGHT VOLTAGE
CHARGE,
IGBT DRIVE
VBATT
HGND
17 16 15 14 13
0
E
6
2
7
3
8
R002
4.7M
R003
33
1
LND005
R280.0
P13.0
XE_L
4
Q001
CY25BAJ-8F-T23
FLASH DRIVE
C003
XX
16
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
DSC-H1
4-9
4-10
Note :
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
ST-123
For Schematic Diagram
• Refer to page 4-53 for printed wiring board.
2
1
3
5
4
SW-447 BOARD(1/2)
A_3.2V
FUNCTION SWITCH
A
6
A_3.2V
VST_C_RESET
XX MARK:NO MOUNT
VST_C_RESET
YAW_AD
YAW_AD
PITCH_AD
R457
5600
ZOOM W
ZOOM T
S452
VAP_DD_ON
MENU
2
7
5
3
1
CN452 6P
2 NO
1 1st
2 NO
1 1st
1
N.C.
3
4 2nd
3
4 2nd
2
N.C.
3
N.C.
4
BL_L
6
5
6
5
1
4
3
S456
2
KEY_AD1
3
D_3.2V
4
REG_GND
5
VST_C_RESET
6
REG_GND
7
YAW_AD
8
REG_GND
9
PITCH_AD
10
REG_GND
11
VAP_DD_ON
12
A_3.2V
13
A_3.2V
14
REG_GND
S453
15
REG_GND
DUST
16
BL_H
17
BL_H
18
BL_L
19
BL_L
20
XACCESS_LED
D452
MAZW068H0LS0
3
3
8
6
4
2
4
2
R453
RB451
2200X4
1
VST_C_RESET
YAW_AD
R454
5600
1
S457
2
1
SET
4
D
S454
2
1
4
3
S460
PITCH_AD
RIGHT
4
3
3
R455
27k
LEFT
2
1
S458
DOWN
4
E
2
1
4
3
D451
1SS387-TPL3
2
VAP_DD_ON
A_3.2V
3
REG_GND
LND451
STATIC_GND
16
BL_H
2
3
DISP
2
6
KEY_AD0
7
5
3
1
C
N.C.
1
1
4
5
330
TO
SW-006
FLEXIBLE FLAT CABLE
(PAGE 4-18)
D455
SML-310LTT86
(ACCESS)
DSC-H1
4-11
LED901
LCD
BACK LIGHT
CN451 20P
1
UP
S451
(2/2)
8
6
4
2
S455
@W01
PITCH_AD
VAP_DD_ON
RB452
2200X4
B
R456
27k
S459
8
7
4-12
SW-447(1/2)
For Schematic Diagram
• Refer to page 4-53 for printed wiring board.
2
1
3
SW-447 BOARD(2/2)
5
6
NO MARK:REC/PB MODE
R :REC MODE
P :PB MODE
PITCH/YAW SENSOR AMP
A
4
XX MARK:NO MOUNT
7
Q401,402
3.2V SWITCH
L401
10uH
R3.2
P0.5 1
Q401
2SA2029T2LQ/R
R2.5
P3.2
3.2
3
2
R0.1
P3.2 1
B
8
R412
47k
R411
1k
2
IC401
A_3.2V
R3.2
P0
VAP_DD_ON
Q402
DTC144EMT2L
PITCH/YAW SENSOR AMP
@W01
(1/2)
3
PITCH_AD
IC0401
R1.3
P0
SE401
(PITCH SENSOR)
3
C
R403
15k
C404
0.33u
R404
1M
R1.3
P0
R405
10k
R1.3
P0
1
C401
22u
6.3V
TA A
2
4
R1.3
P0.2
C406
10u
C408
10u
R401
22k
R402
22k
R1.3
P0
R1.3
P0
C405
0.047u
D
R0.9
P0
R0.7
P0
C403
0.1u
1
PASS
R3.2/P0.5
VCC
2
OUT1
C_RESET
3
4
AM1
OUT2
Vref1
AM2
C411
0.1u
20
19
18
17
5
HO1
Vref2
16
6
HI1
HO2
15
7
LO1
HI2
14
8
LIA1
LO2
13
9
LIB1
LIA2
12
10
GND
LIB2
11
R0
P3.1
VST_C_RESET
R1.2
P0
R1.3
P0
R406
1M
R1.3
P0
R407
10k
3
1
2
SE402
(YAW SENSOR)
YAW_AD
R408
15k
C414
0.33u
R1.3
P0.2
R1.3
P0
C409
10u
C412
10u
R1.3
P0
R0.8
P0
C413
0.047u
R409
22k
R410
22k
R0.6
P0
C410
0.047u
4
C402
22u
6.3V
TA A
C407
0.047u
NJM3230V(TE2)
C416
22u
6.3V
TA A
C415
0.1u
E
REG_GND
16
DSC-H1
4-13
4-14
SW-447(2/2)
For Schematic Diagram
• Refer to page 4-47for printed wiring board.
2
1
3
4
AF-102 FLEXIBLE BOARD
10P
XLENS_COVER_SENSE
1
REG_GND
2
2
1
D001
DOR5073
(AF LED)
AF LED,LENS COVER SW
A
5
D_3.2V
3
XAF_LED
4
1
6
LND001
2
5
XSTRB_POPUP
5
LND002
3
4
39P
REG_GND
6
STRB_PLUNGER
7
STRB_PLUNGER
8
REG_GND
9
REG_GND
10
LND006
16
V8
VST
36
36
VST
V7B
35
35
V7B
V3B
34
34
V3B
REG_GND
V7A
33
33
V7A
6
REG_GND
V3A
32
32
V3A
V6
31
31
V6
V2
30
30
V2
VHLD
29
29
VHLD
V1B
28
28
V1B
V5B
27
27
V5B
V1A
26
26
V1A
V5A
25
25
V5A
REG_GND
24
24
REG_GND
REG_GND
23
23
REG_GND
CCD_OUT
22
22
CCD_OUT
REG_GND
21
21
REG_GND
(PAGE 4-8)
B
(PAGE 4-23
OF LEVEL3)
5
REG_GND
20
20
REG_GND
REG_GND
19
19
REG_GND
RG
18
18
RG
MS-029 FLEXIBLE FLAT CABLE
REG_GND
17
17
REG_GND
CAM_15V_CD
16
16
CAM_15V_CD
SY-MS RELAY
POWER_SAVE
15
15
POWER_SAVE
CAM_-7.5V_CD
14
14
CAM_-7.5V_CD
REG_GND
13
13
REG_GND
H1A
12
12
H1A
REG_GND
11
11
REG_GND
H2A
10
10
H2A
REG_GND
9
9
REG_GND
H1B
8
8
H1B
REG_GND
7
7
REG_GND
H2B
6
6
H2B
REG_GND
5
5
REG_GND
RANDOM_TRIGGER
4
4
RANDOM_TRIGGER
VSUB
3
3
VSUB
CSUB
2
2
CSUB
REG_GND
1
1
REG_GND
12P
REG_GND
12
12
REG_GND
MS_VCC
11
11
MS_VCC
MS_CLK
TO
SY-127 BOARD(10/11)
CN506
(PAGE 4-39
OF LEVEL3)
MS_D3
10
9
10
9
MS_CLK
8
8
XMS_IN
MS_D2
7
7
MS_D2
MS_D0
6
6
MS_D0
MS_D1
5
5
MS_D1
REG_GND
4
3
4
3
E
MS_D3
XMS_IN
MS_BS
C
37
5
4
12P
B
37
STRB_PLUNGER
D
A
V4
V8
4
LND021
3
38
STRB_PLUNGER
TO
SY-127 BOARD
(2/11)
CN502
2
38
3
TO
PL-039 BOARD
CN301
C
1
REG_GND
V4
REG_GND
LND020
LND010
39
2
LND011
LND009
39
XSTRB_POPUP
LND016
LND008
39P
REG_GND
1
LND013
LND007
B
6P
LND012
LND005
5
SY-CD RELAY
A
LND004
(PAGE 4-39
OF LEVEL3)
4
FP-224 FLEXIBLE BOARD
S001
(LENS COVER OPEN)
LND003
TO
SY-127 BOARD(10/11)
CN507
3
TO
MS-275 BOARD
CN251
(PAGE 4-7)
MS_BS
REG_GND
VL_3V
2
2
VL_3V
REG_GND
1
1
REG_GND
MS-029 FLEXIBLE FLAT CABLE is replaced as a block.
So that this PRINTED WIRING BOARD is omitted.
F
16
TO
CD-576 BOARD
CN101
(PAGE 4-5)
FP-224 FLEXIBLE BOARD is replaced as a block.
So that this PRINTED WIRING BOARD is omitted.
16
DSC-H1
4-15
4-16
AF-102/FP-224/MS-029
3
2
1
4
SY-ST RELAY
B
XX MARK:NO MOUNT
20P
20P
12
ST_UNREG
ST_UNREG
11
11
ST_UNREG
KEY_AD0
20
20
KEY_AD0
ST_UNREG
KEY_AD1
19
19
KEY_AD1
D_3.2V
18
18
D_3.2V
REG_GND
17
17
REG_GND
VST_C_RESET
16
16
VST_C_RESET
REG_GND
15
15
REG_GND
YAW_AD
14
14
YAW_AD
REG_GND
13
13
REG_GND
PITCH_AD
12
12
PITCH_AD
10
10
ST_5V
9
9
ST_5V
REG_GND
8
8
REG_GND
STRB_ON
7
7
STRB_ON
XSTRB_FULL
5
SY-SW RELAY
12
STRB_CHG_CONT
16
4
ST_UNREG
ST_UNREG
(PAGE 4-40
OF LEVEL3)
A
12P
12P
TO
SY-127 BOARD
(10/11)
CN501
3
SW-006 FLEXIBLE FLAT CABLE
ST-001 FLEXIBLE FLAT CABLE
A
2
1
5
6
6
5
5
TO
ST-123 BOARD
CN001
(PAGE 4-9)
STRB_CHG_CONT
XSTRB_FULL
STRB_CHG
4
4
STRB_CHG
REG_GND
3
3
REG_GND
REG_GND
2
2
REG_GND
REG_GND
1
1
REG_GND
B
TO
SY-127 BOARD
(10/11)
CN513
(PAGE 4-40
OF LEVEL3)
ST-001 FLEXIBLE FLAT CABLE is replaced as a block.
So that this PRINTED WIRING BOARD is omitted.
C
16
For Schematic Diagram
• Refer to page 4-52 for printed wiring board.
REG_GND
11
11
REG_GND
XFE_ON/VAP_DD_ON
10
10
XFE_ON/VAP_DD_ON
A_3.2V
9
9
A_3.2V
A_3.2V
8
8
A_3.2V
REG_GND
7
7
REG_GND
REG_GND
6
6
REG_GND
BL_H
5
5
BL_H
BL_H
4
4
BL_H
BL_L
3
3
BL_L
BL_L
2
2
BL_L
XACCESS_LED
1
1
XACCESS_LED
TO
SW-447 BOARD
(1/2)
CN451
(PAGE 4-12)
SW-006 FLEXIBLE FLAT CABLE is replaced as a block.
So that this PRINTED WIRING BOARD is omitted.
1
2
3
4
5
ST-124 FLEXIBLE BOARD
FLASH
A
XX MARK:NO MOUNT
LND005
LND001
XE_H
XE_+
R001
1M
C002
0.047u
250V
B
L001
TRIGGER COIL
LND004
XENON
TUBE
TRIGGER
TO
ST-123 BOARD
C003
0.01u
250V
(PAGE 4-10)
LND002
XE_L
XE_D001
RR255L-400TE25
C
LND003
REG_GND
R002
100k
1/10W
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Note :
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
16
DSC-H1
4-17
4-18
ST-001/ST-124/SW-006
1
2
3
5
4
R111
2K
CONTROL SWITCH BLOCK
(SW51780)
A
S101
S102
AF/MF
BRK
R106
2K
B
R113
2K
6
R105
2K
R107
2K
7
14
13
5
12
4
11
3
10
2
1
8
R110
2K
R101
49003
8
R112
2K
R109
2K
R104
2K
7
6
9
R115
2K
R116
2K
R117
2K
S106
EVF/LCD
S107
STEADY SHOT
R118
2K
R114
2K
R108
10K
C
S103
SHUTTER
1
3
S104
POWER
S105
JOG DIAL
4
2
D
D102
(POWER)
D101
(FLASH)
E
LND115
10
9
8
7
6
5
4
3
REG_GND
XSHIFT_ON
XSHUTTER_SW
XAE_LOCK_SW
JOG_B
JOG_A
KEY_AD2
MODE_DIAL1
1
11
XPWR_ON
2
12
XPWR_LED
A_3.2V
13
D_3.2V
MODE_DIAL0
14
XSTRB_LED
CONTROL SWITCH BLOCK(SW51780) is
replaced as a block.
So that this PRINTED WIRING BOARD is omitted.
14P
STATIC_GND
16
TO SY-127 BOARD(10/11)
CN514
(PAGE 4-41 OF LEVEL3)
Schematic diagram of the CH-169 and SY-127 board
are not shown.
Pages from 4-21 to 4-44 are not shown.
DSC-H1
4-19
4-20
SW51780
4-3. PRINTED WIRING BOARDS
Link
CD-576 BOARD
PL-039 BOARD
MS-275 BOARD
SW-447 BOARD
ST-123 BOARD
EV-016 FLEXIBLE BOARD
ST-124 FLEXIBLE BOARD
AF-102 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
NAME
AF-102
CD-576
CH-169
EV-016
MS-275
PL-039
ST-123
ST-124
SW-447
SY-127
DSC-H1
CIRCUIT BOARDS LOCATION
WAVEFORMS
FLEXIBLE BOARDS LOCATION
FUNCTION
AF LED, LENS COVER SW
CCD IMAGER
CCD SIGNAL PROCESS
EVF, BACK LIGHT
MEMORY STICK, LI BATTERY
PLUNGER
FLASH DRIVE
FLASH
FUNCTION SW, PITCH/YAW SENSOR AMP
LENS DRIVE, CAMERA A/D CONV., TIMING GENERATOR, CAMERA DSP,
SYSTEM CONTROL, 256Mbit SDRAM, FLASH MEMORY, SUPER AND FLASH MEMORY,
A/V AMP, USB/AV JACK, SP, MIC, PANEL DRIVE, STEADY SHOT CONTROL,
LENS SERVO, CONNECTOR, DC/DC CONVERTER
4-3. PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR WIRING BOARDS
(In addition to this, the necessary note is printed in each block)
(For printed wiring boards)
•
: Uses unleaded solder.
: Pattern from the side which enables seeing.
•
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• Circled numbers refer to waveforms.
• There are a few cases that the part printed on diagram
isn’t mounted in this model.
• C: panel designation
• Chip parts.
Transistor
6 5 4 4 5 6 5
C
B
E
4 4
waveforms
parts location
4-61
–
–
–
–
–
–
–
4-62
2
2
2
1
2
2
1
1
8
DSC-H1
4-45
3
3
1 23
2
1 2
1 2
1 6 54
1
2 3
4
3
3
4
1 1 2
4
3
2
1
2 2
1 3
4
5 4 3 3 4 5 2
1
pattern
4-63
–
–
–
–
4-63
–
–
4-64
3
1
(shown on page) (shown on page) number of layers layers not shown
CD-576
MS-275
ST-123
ST-124
PL-039
SW-447
EV-016
AF-102
SY-127
Diode
1 2 3 3 2 1 1 2 3 3 2 1
BOARD INFORMATION
board name
5
–
–
–
–
–
–
–
–
2 to 7
4
3 2
5
4
1
3 1
6
3
4
1
2
4-3. PRINTED WIRING BOARDS
•
• Refer to page 4-45 for common note for printed wiring board.
: Uses unleaded solder.
AF-102 FLEXIBLE BOARD
LND010
LND009
LND008
LND007
LND006
LND005
LND004
LND003
LND002
LND001
1
K
6
10
LND021
LND020
LND011
LND016
LND013
LND012
A
1-867-129D001
3
2
>PI<
1
16
1-867-129-
AF-102
1
AF LED
B
S001
(LENS COVER OPEN)
3
1
11
1
4
2
6
3
4
MS-275 BOARD(SIDE A)
5
LND251
MS-275 BOARD(SIDE B)
12
CN251
1
1
C252
R253
FB252
11
D251
+
CL262 +
CL256
FB254
FB253
FB251
BT251
LITHIUM BATTERY
(SECONDARY)
CL257
CL251
R251
MEMORY STICK
CONNECTOR
1-867-122-
MS-275
>EP GW <
1-867-122-
CN252
A C251
10
12
11
1-867-122-
11
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
DSC-H1
4-47
4-48
AF-102/MS-275
•
• Refer to page 4-45 for common note for printed wiring board.
: Uses unleaded solder.
CD-576 BOARD(SIDE A)
7
7 6 5
A
1
14
C101
R106
6
C102
A
CD-576 BOARD(SIDE B)
Note:IC101 is not included in
this COMPLETE of CD-576 board
IC101
4
C103
IC102
1
3
C107
28
15
2
B
1
1
3
B
4
C105
C109
R110
C108
312
11
1-867-121-
R109
R104
R105
Q102
2
Q104
312
38
CN101
1
R108
39
1-867-12116
1
2
3
3
2
1
11
16
EV-016 FLEXIBLE BOARD
K
1
22
11
1-867-128-
1
16
>PI<
EV-016
1-867-128-
D001
CN001
2
A
20
LND001
LND002
LND003
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
21
1
2
3
4
DSC-H1
4-49
4-50
CD-576/EV-016
•
• Refer to page 4-45 for common note for printed wiring board.
: Uses unleaded solder.
ST-123 BOARD(SIDE B)
C002
K
5
A
1
L001
12
A
D001
C003
2
1
4
12 13
2
8 9
6
R001
17
T001
5
4
1
16
1
4
3
R004
LND003
R002
R003
8
LND005
Q001
C004
IC001
5
C001
C005
A
1
ST-123
>EP GW<
1-867-123-
LND004
ST-123 BOARD(SIDE A)
CN001
11
1-867-12311
16
1
2
3
4
4
PL-039 BOARD
(SIDE B)
PL-039 BOARD
(SIDE A)
3
2
(FLASH POP UP)
2
RY301
11
>PI<
R001
1
LND006 2
1
>EP GW<
1-867-124-
C002
R002 LND003
LND001
C301
1-867124-
S301
D301
C003
D302
PL-039
PL-039
1-867-124-
LND002
6
CN301
L001
LND005
3
1-867-127-
11
LND004
1-867-124-
11
DSC-H1
4-51
16
ST-124 FLEXIBLE BOARD
D001
1
1
ST-124-
1-867-123-
4-52
ST-123/PL-039/ST-124
•
• Refer to page 4-45 for common note for printed wiring board.
: Uses unleaded solder.
SW-447 BOARD
CN451
1
20
A
S457
S460
2
1
2
C407
C410
ZOOM W
11
IC0401
ZOOM T
5
1
1
10
R405
C405
R401
2
S455
3
2
6
4
8
RB452
1
7
CN452
C408
7
8
RB451
2
K
A
16
SE401
1
Q401
D455
C
312
4
6
3
4
R411
20
1
2
C402
2
3 12
1
A
R412
4
+
(PITCH SENSOR)
R453
+
2
S453
1
A
A
R408
S456
2
3
R455
4
4
3
C401
RIGHT
D451
D452
312
R457
3
1
2
R456
R454
1
DUST
3
2
C403
R402
S458
4
C416
+
4
2
S459
R410
R409
C413
3
4
B
UP
SET
DOWN
3
2
2
C415
1
1
L401
2
(YAW SENSOR)
C412
S454
5
1
SE402
S452
Q402
1
4
C411
S451
3
4
C409
3
1
C406
4
3
6
1
1-867-125-
1
3
MENU
LEFT
C414
R403R404 R407
C404
R406
DISP
3
11
4
Printed wiring board of the CH-169 and SY-127 board
are not shown.
Pages from 4-55 to 4-60 are not shown.
DSC-H1
4-53
4-54
SW-447
4-3. PRINTED WIRING BOARDS
4-4. WAVEFORMS
CD-576 BOARD (CAMERA MODE)
1 IC101 1-5,7-9,qa
6 IC101 qj
4.6 Vp-p
7.7 Vp-p
265 us
74 ns
2 IC101 6
7 IC101 qk,ql,wj,wk
7.7 Vp-p
4.4 Vp-p
265 us
74 ns
3 IC101 q;
7.7 Vp-p
265 us
4 IC101 qs-qf
7.7 Vp-p
265 us
5 IC101 qg
1.8 Vp-p
265 us
Waveforms of the SY-127 board are not
shown.
Page 4-62 is not shown.
DSC-H1
4-61
CD-576
4-3. PRINTED WIRING BOARDS
no mark : side A
* mark : side B
4-5. MOUNTED PARTS LOCATION
CD-576 BOARD
* C101
* C102
* C103
* C105
* C107
* C108
* C109
A-1
A-1
A-1
B-3
B-1
B-3
B-3
* CN101 B-1
IC101
* IC102
A-3
A-1
* Q102
* Q104
B-3
B-2
R104
R105
R106
R108
R109
R110
B-3
B-3
A-1
B-2
B-2
B-3
*
*
*
*
*
*
SW-447 BOARD
C401
C402
C403
C404
C405
C406
C407
C408
C409
C410
C411
C412
C413
C414
C415
C416
B-3
B-3
C-4
B-3
B-4
C-3
B-4
C-3
C-3
B-4
B-3
C-4
B-4
B-3
B-4
B-3
CN451 A-3
CN452 C-4
D451
D452
D455
B-1
B-1
C-1
IC0401 B-4
L401
B-3
Q401
Q402
C-3
C-2
R401
R402
R403
R404
R405
R406
R407
R408
R409
R410
R411
R412
R453
R454
R455
R456
R457
C-4
C-4
B-3
B-3
B-3
B-3
B-3
B-3
B-4
B-4
B-2
B-3
C-1
B-1
C-1
B-1
C-1
RB451 C-2
RB452 C-4
S451
S452
S453
S454
S455
S456
S457
S458
S459
S460
A-1
A-3
C-1
A-2
B-4
B-2
B-2
B-1
A-4
C-2
SE401
SE402
C-3
A-3
Mounted parts location of the SY-127 board are not
shown.
Page 4-64 is not shown.
DSC-H1
4-63E
CD-576/SW-447
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
EXPLODED VIEWS
Link
D
I
H
OVERALL SECTION
LCD/CABINET(REAR)
SECTION
B
LENS SECTION
Link
DSC-H1
EVF SECTION
MAIN SECTION
E
F
G
A
CABINET(FRONT)
SECTION
C
ST SECTION
ELECTRICAL PARTS LIST
ACCESSORIES
AF-102 Flexible BOARD
A
CD-576 BOARD
B
EV-016 Flexible BOARD
C
MS-275 BOARD
D
PL-039 BOARD
E
ST-123 BOARD
F
ST-124 Flexible BOARD
G
SW-447 BOARD
H
SY-127 BOARD
I
5. REPAIR PARTS LIST
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from
the original one.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not
supplied.
• Due to standardization, replacements in the parts list may be different from
the parts specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
• Abbreviation
CND : Canadian model
HK : Hong Kong model
AUS : Australian model
CH : Chinese model
KR : Korea model
JE : Tourist model
J
: Japanese model
Swedish
Korean
Russian
Arabic
Dutch
Simplified
Chinese
Traditional
Chinese
Portugal
Italian
Spanish
German
French
Japanese
English
Area
Language that can be selected about SY-127 board
z
GP1
J
GP2
US
CND
AUS
Vietnam
z z
GP3
AEP
UK
z z z z z z
GP4
E
AR
BR
TW
z
z
z
z
z
GP5
JE
HK
CH
KR
z
z
z
z
z
z z
z
z
z z z
z
z
DSC-H1
5-1
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
5-1-1. OVERALL SECTION
Cabinet (front) section
(See page 5-8)
E
1
D
A
B
Lens section
(See page 5-7)
C
A
3
B
C
2
D
LCD section,
Cabinet (rear) section
(See page 5-4)
4
7
-12
SY
1
2
2
2
Main section
(See page 5-5)
E
1
1
Ref. No.
1
2
3
4
Part No.
Description
3-056-233-21
3-080-204-11
A-1119-330-A
1-830-604-11
SCREW (M2), LOCK ACE, P2
SCREW, TAPPING, P2
SW-447 BOARD, COMPLETE
CABLE, FLEXIBLE FLAT (SW-006)
DSC-H1
5-3
5. REPAIR PARTS LIST
5-1-2. LCD SECTION, CABINET(REAR) SECTION
ns : not supplied
51
60
58
55
LED901
52
ns
53
LCD901
59
ns
56
54
57
Ref. No.
51
52
53
54
55
Part No.
Description
3-080-204-11
2-629-828-01
2-629-831-01
2-629-769-01
2-629-767-01
SCREW, TAPPING, P2
SHEET METAL (L), STRAP
LID, DC
WINDOW, LCD
EYE CUP
Ref. No.
56
57
58
59
60
Part No.
Description
2-629-833-01
2-629-834-01
X-2055-957-1
X-2055-956-1
2-629-835-01
SHEET, LCD ADHESIVE
LID, JK
FRAME ASSY, LCD
CABINET (REAR) ASSY
BRACKET (L), STRAP
LCD901 8-753-229-36 ACX336AK-3
LED901 1-479-015-11 BLOCK, LIGHT GUIDE PLATE (2.5)
DSC-H1
5-4
5. REPAIR PARTS LIST
5-1-3. MAIN SECTION
EVF section
(See page 5-6)
ns : not supplied
102
ns
BT251
103
BT901
MS
-27
5
107
108
ns
104
110
109
7
-12
SY
101
(Note)
103
SP901
106
105
: BT251 (Lithium battery) MS-275 board on the mount position. (See page 4-48)
Note : Refer to the table of page 5-1 about language of SY-127 board.
Ref. No.
Part No.
Description
101
102
103
104
105
X-2055-945-1
A-1119-327-A
3-080-204-11
1-830-602-11
2-629-768-01
HOLDER ASSY, BATTERY
MS-275 BOARD, COMPLETE
SCREW, TAPPING, P2
CABLE, FLEXIBLE FLAT (MS-029)
RETAINER, SP
106
107
108
109
109
2-630-230-01
2-629-759-01
2-629-760-01
A-1127-774-A
A-1127-775-A
LABEL, FUSE REPLACEMENT CAUTION
SHAFT, BT
SPRING, BT, OPEN
SY-127 BOARD, COMPLETE (SERVICE) (GP1)
SY-127 BOARD, COMPLETE (SERVICE) (GP2)
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No.
109
109
109
110
SP901
0 BT251
BT901
Note :
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Part No.
Description
A-1127-776-A
A-1127-777-A
A-1127-778-A
X-2059-858-1
1-825-923-41
SY-127 BOARD, COMPLETE (SERVICE) (GP3)
SY-127 BOARD, COMPLETE (SERVICE) (GP4)
SY-127 BOARD, COMPLETE (SERVICE) (GP5)
LID ASSY (SERVICE), BT
LOUDSPEAKER (1.3CM)
1-528-999-61 BATTERY, LITHIUM SECONDARY
1-780-267-11 TERMINAL BOARD, BATTERY
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
DSC-H1
5-5
5. REPAIR PARTS LIST
5-1-4. EVF SECTION
156
157
LCD902
155
154
153
152
151
Ref. No.
151
152
153
154
155
Part No.
Description
A-1119-332-A
3-089-447-01
3-089-448-01
3-089-445-01
3-089-446-01
EV-016 BOARD, COMPLETE
GUIDE, LAMP
CUSHION, LB
ILLUMINATOR
SHEET, PRISM
Ref. No.
Part No.
Description
156
X-2055-959-1 HOLDER ASSY, LCD
157
X-2055-958-1 LENS ASSY, VF
LCD902 8-753-233-08 LCX067AKEB-1
DSC-H1
5-6
5. REPAIR PARTS LIST
5-1-5. LENS SECTION
207
201
208
IC101
209
206
76
204
-5
CD
210
202
205
203
Ref. No.
201
202
203
204
205
Part No.
Description
A-1127-773-A
2-631-861-01
2-629-774-01
2-629-773-01
3-078-890-21
OPTICAL UNIT (B173A) (SERVICE)
SHEET (CD)
HEAT SINK, CCD
FRAME, LENS
SCREW, TAPPING
Ref. No.
206
207
208
209
210
IC101
Part No.
205
Description
2-592-605-01
1-788-298-11
2-592-693-01
A-1119-326-A
RUBBER (TM), SEAL
OPTICAL FILTER BLOCK
PLATE (T), LIGHT INTERCEPTION
CD-576 BOARD, COMPLETE
(IC101 is not included in this COMPLETE board.)
1-867-126-11 FP-224 FLEXIBLE BOARD
A-1122-935-A CCD BLOCK ASSY (CCD IMAGER)
(IC101 is not included in this COMPLETE board of CD-576.)
Be sure to read “Precautions upon replacing CCD imager”
on page 4-1 when changing the CCD imager.
DSC-H1
5-7
5. REPAIR PARTS LIST
5-1-6. CABINET(FRONT) SECTION
ns : not supplied
ST section
(See page 5-9)
B
259
A
256
260
253
ns
258
ns
B
259
MIC901
261
259
ns
252
254
259
251
259
257
ns
A
255
259
262
Ref. No.
251
252
253
254
255
Part No.
Description
X-2055-951-1
2-629-813-01
2-629-815-01
2-629-812-01
2-629-783-01
CABINET (FRONT) ASSY
PLATE, ORNAMENTAL
GRIP
SHEET METAL (R), STRAP
SCREW, TRIPOD
Ref. No.
256
257
258
259
260
Part No.
Description
1-830-603-11
2-629-781-01
1-479-260-11
3-080-204-11
2-629-820-01
CABLE, FLEXIBLE FLAT (ST-001)
PLATE (LENS), FRONT GROUND
SWITCH BLOCK, CONTROL (SW51780)
SCREW, TAPPING, P2
RING (W), LENS
261
2-629-817-01 HOLDER, MICROPHONE
262
A-1119-333-A AF-102 FLEXIBLE BOARD, COMPLETE
MIC901 1-542-446-81 MICROPHONE
DSC-H1
5-8
5. REPAIR PARTS LIST
5-1-7. ST SECTION
306
303
304
Blue
White
301
309
Red
308
310
RY301
305
307
302
ns
PRECAUTION DURING SOLENOID PLUNGER INSTALLATION
6
5
301
3
4
2
1
Ref. No.
301
302
303
304
305
Part No.
Description
3-080-204-11
A-1119-329-A
X-2055-955-1
A-1119-331-A
A-1119-328-A
SCREW, TAPPING, P2
PL-039 BOARD, COMPLETE
BASE ASSY, ST
ST-124 BOARD, COMPLETE
ST-123 BOARD, COMPLETE
1 Plunger solenoid
4 PL-039 board
2 Two claws
5 Apply the soldering in two points.
3 Solenoid retainer
6 Tapping screw (M1.7x4) black
Ref. No.
DSC-H1
5-9
Part No.
Description
306
307
308
309
310
2-629-816-01
2-629-818-01
1-963-811-11
1-963-811-21
1-963-811-31
COVER, ST
RETAINER, SOLENOID
HARNESS (HA-001) (RED)
HARNESS (HA-001) (WHITE)
HARNESS (HA-001) (BLUE)
RY301
1-455-038-11 SOLENOID, PLUNGER
5. REPAIR PARTS LIST
Checking supplied accessories.
Make sure that the following accessories are supplied with your camcorder.
CHARGER, BATTERY (US,CND,J) (1)
1-479-378-11
BATTERY CHARGER (BC-CS2) (1)
(AEP,UK,E,AUS,HK,JE) (1)
1-479-378-21
BATTERY CHARGER (BC-CS2) (1)
(KR,CH)
1-479-378-31
CORD, POWER (1)
(US,CND)
1-790-107-42
CORD, POWER (1)
(AEP,E)
1-823-946-12
CORD, POWER (1)
(AUS)
1-827-945-12
POWER-SUPPLY CORD (1)
(KR)
1-823-947-12
CORD, POWER (1)
(UK,HK)
1-783-374-12
CORD, POWER (1)
(CH)
1-782-476-51
CORD, POWER (1)
(JE,J)
1-790-732-12
CASE, BATTERY CARRYING (1)
3-074-757-01
CORD WITH CONNECTOR (1)
(USB 5P)
1-827-038-11
RING, ATTACHMENT (1)
2-629-861-01
CAP ASSY, LENS (1)
X-2055-960-1
STRING, CAP
3-979-194-31
CORD, CONNECTION (1)
1-824-519-11
C-S APPLI SOFT V1.6 (1)
2-583-853-01
BELT, SHOULDER (1)
2-629-892-01
ADAPTOR, CONVERSION 2P (1)
(JE,E)
1-573-856-12
• Abbreviation
CND : Canadian model
HK : Hong Kong model
AUS : Australian model
CH : Chinese model
KR : Korea model
JE
: Tourist model
J
: Japanese model
HOOD, LENS (1)
2-629-860-01
Other accessories
2-629-893-01 INSTRUCTION (READ THIS FIRST) (JAPANESE)(J)
2-629-893-11 INSTRUCTION (READ THIS FIRST)(ENGLISH)
(US,CND,AEP,UK,E,HK,AUS,JE)
2-629-893-21 INSTRUCTION (READ THIS FIRST) (FRENCH/ITALIAN)
(CND,AEP)
2-629-893-31 INSTRUCTION (READ THIS FIRST)
(SPANISH/PORTUGUESE)(AEP,E,JE)
2-629-893-41 INSTRUCTION (READ THIS FIRST) (GERMAN/DUTCH)
(AEP)
2-629-893-51 INSTRUCTION (READ THIS FIRST)
(TRADITIONAL CHINESE/SIMPLIEIED CHINESE)(E,HK,JE,CH)
2-629-893-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN/SWEDISH)
(AEP)
2-629-893-71 INSTRUCTION (READ THIS FIRST) (ARABIC/PERSIAN)(E)
2-629-893-81 INSTRUCTION (READ THIS FIRST) (KOREAN)(KR,JE)
2-629-893-91 INSTRUCTION (READ THIS FIRST) (POLISH/CZECH)
(AEP)
2-629-894-11 INSTRUCTION (READ THIS FIRST)
(HUNGARIAN/SLOVAK)(AEP)
DSC-H1
5-10
2-629-895-01 INSTRUCTION (USER'S GUIDE) (JAPANESE)(J)
2-629-895-11 INSTRUCTION (USER'S GUIDE) (ENGLISH)
(US,CND,AEP,UK,E,HK,AUS,JE)
2-629-895-21 INSTRUCTION (USER'S GUIDE) (FRENCH/ITALIAN)
(CND,AEP)
2-629-895-31 INSTRUCTION (USER'S GUIDE)
(SPANISH/PORTUGUESE)(AEP,E,JE)
2-629-895-41 INSTRUCTION (USER'S GUIDE) (GERMAN/DUTCH)(AEP)
2-629-895-51 INSTRUCTION (USER'S GUIDE)
(TRADITIONAL CHINESE/SIMPLIEIED CHINESE)(E,HK,JE,CH)
2-629-895-61 INSTRUCTION (USER'S GUIDE) (RUSSIAN/SWEDISH)
(AEP)
2-629-895-71 INSTRUCTION (USER'S GUIDE) (ARABIC/PERSIAN)(E)
2-629-895-81 INSTRUCTION (USER'S GUIDE) (KOREAN)(KR)
2-629-895-91 INSTRUCTION (USER'S GUIDE) (POLISH/CZECH)(AEP)
2-629-943-11 INSTRUCTION (USER'S GUIDE) (HUNGARIAN/SLOVAK)
(AEP)
AF-102
CD-576
EV-016
MS-275
PL-039
5-2. ELECTRICAL PARTS LIST
Ref. No.
Part No.
Description
Ref. No.
A-1119-333-A AF-102 FLEXIBLE BOARD, COMPLETE
***********************
(D001 and S001 are included in this COMPLETE board.)
Part No.
Description
A-1119-327-A MS-275 BOARD, COMPLETE
***********************
< BATTERY >
< DIODE >
0 BT251
D001
not supplied
1-756-539-21 BATTERY, LITHIUM SECONDARY
DIODE DOR5073
< CAPACITOR >
< SWITCH >
C252
1-125-777-11 CERAMIC CHIP
S001
not supplied
SWITCH, PUSH (1 KEY)
************************************************************
0.1uF
10%
10V
< CONNECTOR >
A-1119-326-A CD-576 BOARD, COMPLETE
**********************
(IC101 is not included in this COMPLETE board.)
CN251
CN252
1-816-644-31 FFC/FPC CONNECTOR (LIF) 12P
1-815-572-71 CONNECTOR, MEMORY STICK
< FERRITE BEAD >
< CAPACITOR >
C101
C102
C105
C107
C109
1-164-943-81
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
FB251
FB252
FB253
FB254
16V
16V
16V
16V
16V
R251
1-218-990-81 SHORT CHIP
0
R253
1-218-953-11 RES-CHIP
1K
5%
1/16W
************************************************************
1-817-544-31 CONNECTOR, FPC (ZIF) 39P
< IC >
IC101
IC102
A-1119-329-A PL-039 BOARD, COMPLETE
**********************
A-1122-935-A CCD BLOCK ASSY (CCD IMAGER)
(IC101 is not included in this COMPLETE of CD-576 board.)
< CAPACITOR >
8-753-230-85 IC CXA3691EN-T9
C301
< TRANSISTOR >
Q102
Q104
6-550-119-01 TRANSISTOR
6-550-119-01 TRANSISTOR
BEAD, FERRITE (1005)
BEAD, FERRITE (1005)
BEAD, FERRITE (1005)
BEAD, FERRITE (1005)
< RESISTOR >
< CONNECTOR >
CN101
1-400-807-21
1-400-807-21
1-400-807-21
1-400-807-21
1-165-908-11 CERAMIC CHIP
1uF
10%
10V
< CONNECTOR >
DTC144EMT2L
DTC144EMT2L
CN301
1-816-654-31 FFC/FPC CONNECTOR (LIF) 6P
< DIODE >
< RESISTOR >
D302
R104
R105
R106
R108
R109
1-218-955-11
1-218-954-11
1-218-981-11
1-218-990-81
1-218-982-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
1.5K
1.2K
220K
0
270K
5%
5%
5%
1/16W
1/16W
1/16W
5%
1/16W
8-719-988-61 DIODE 1SS355TE-17
< RELAY >
RY301
1-455-038-11 SOLENOID, PLUNGER
< SWITCH >
R110
1-218-989-11 RES-CHIP
1M
5%
1/16W
************************************************************
S301
1-786-179-31 SWITCH, PUSH (1KEY)
************************************************************
A-1119-332-A EV-016 FLEXIBLE BOARD, COMPLETE
**********************
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
< CONNECTOR >
CN001
1-817-560-31 CONNECTOR, FPC (ZIP) 21P
Note :
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
< DIODE >
D001
6-501-154-01 DIODE NSCW455AT-TY5
************************************************************
Be sure to read “Precautions upon replacing CCD imager”
on page 4-1 when changing the CCD imager.
DSC-H1
5-11
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
ST-123
Ref. No.
Part No.
Description
Ref. No.
A-1119-328-A ST-123 BOARD, COMPLETE
**********************
Part No.
1-100-611-91
1-100-506-91
1-112-468-11
1-100-611-91
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
SW-447
Description
A-1119-330-A SW-447 BOARD, COMPLETE
***********************
< CAPACITOR >
C001
C002
0 C004
C005
ST-124
< CAPACITOR >
22uF
1uF
205uF
22uF
20%
20%
99%
20%
6.3V
6.3V
330V
6.3V
C401
C402
C403
C404
C405
1-119-750-11
1-119-750-11
1-125-777-11
1-128-934-61
1-119-923-11
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
22uF
0.1uF
0.33uF
0.047uF
20%
20%
10%
10%
10%
6.3V
6.3V
10V
10V
10V
C406
C407
C408
C409
C410
1-137-710-11
1-119-923-11
1-137-710-11
1-137-710-11
1-119-923-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.047uF
10uF
10uF
0.047uF
20%
10%
20%
20%
10%
6.3V
10V
6.3V
6.3V
10V
C411
C412
C413
C414
C415
1-125-777-11
1-137-710-11
1-119-923-11
1-128-934-61
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
0.047uF
0.33uF
0.1uF
10%
20%
10%
10%
10%
10V
6.3V
10V
10V
10V
C416
1-119-750-11 TANTAL. CHIP
22uF
20%
6.3V
< CONNECTOR >
CN001
1-816-644-31 FFC/FPC CONNECTOR (LIF) 12P
< DIODE >
0 D001
6-501-141-01 DIODE FT02P80TP
< IC >
0 IC001
6-707-555-01 IC TPS65552RGTR
< COIL >
L001
1-456-499-11 INDUCTOR
4.7uH
< CONNECTOR >
< TRANSISTOR >
0 Q001
6-550-656-01 TRANSISTOR
CN451
CN452
CY25BAJ-8F-T23
1-818-046-11 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 20P
1-818-619-21 CONNECTOR, FFC/FPC (ZIF) 6P
< DIODE >
< RESISTOR >
R001
R002
R003
1-216-864-11 SHORT CHIP
1-243-975-81 METAL CHIP
1-218-935-11 RES-CHIP
0
4.7M
33
5%
5%
D451
D452
D455
1/16W
1/16W
8-719-056-23 DIODE MA2S111-(K8).SO
6-500-776-01 DIODE MAZW068H0LS0
8-719-064-07 DIODE SML-310LTT86
< IC >
< TRANSFORMER >
0 T001
1-443-689-11 TRANSFORMER, D.C.-D.C.CONVERTER
************************************************************
IC0401
8-759-489-19 IC uPC6756GR-8JG-E2
< COIL >
A-1119-331-A ST-124 FLEXIBLE BOARD, COMPLETE
**********************
0
L401
1-469-757-21 INDUCTOR
< TRANSISTOR >
1-479-261-11 FLASH UNIT
Q401
Q402
< CAPACITOR >
C002
C003
1-100-758-11 CERAMIC CHIP
1-100-761-21 CERAMIC CHIP
0.047uF
0.01uF
10%
10%
2SA2029T2LQ/R
DTC144EMT2L
< RESISTOR >
6-500-811-01 DIODE RR255L-400TE25
< COIL >
L001
6-550-232-01 TRANSISTOR
6-550-119-01 TRANSISTOR
250V
250V
< DIODE >
D001
10uH
1-456-193-11 COIL, TRIGGER
< RESISTOR >
R001
1-216-121-11 RES-CHIP
1M
5%
1/10W
R002
1-216-097-11 RES-CHIP
100K
5%
1/10W
************************************************************
R401
R402
R403
R404
R405
1-218-969-11
1-218-969-11
1-218-967-11
1-218-989-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
22K
22K
15K
1M
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R406
R407
R408
R409
R410
1-218-989-11
1-218-965-11
1-218-967-11
1-218-969-11
1-218-969-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1M
10K
15K
22K
22K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
DSC-H1
5-12
Note :
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
SW-447
Ref. No.
Part No.
Description
R411
R412
R453
R454
R455
1-218-953-11
1-218-973-11
1-208-671-11
1-218-962-11
1-218-970-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
R456
R457
1-218-970-11 RES-CHIP
1-218-962-11 RES-CHIP
1K
47K
330
5.6K
27K
5%
5%
0.5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
27K
5.6K
5%
5%
1/16W
1/16W
< COMPOSITION CIRCUIT BLOCK >
RB451
RB452
1-234-376-21 RES, NETWORK
1-234-376-21 RES, NETWORK
2.2K (1005X4)
2.2K (1005X4)
< SWITCH >
S451
S452
S453
S454
S455
1-786-157-11
1-786-157-11
1-786-157-11
1-786-157-11
1-786-525-31
SWITCH, TACTILE (DISP)
SWITCH, TACTILE (MENU)
SWITCH, TACTILE (DUST)
SWITCH, TACTILE (LEFT)
TACTILE SWITCH (ZOOM T)
S456
S457
S458
S459
S460
1-786-157-11
1-786-157-11
1-786-157-11
1-786-525-31
1-786-157-11
SWITCH, TACTILE (UP)
SWITCH, TACTILE (SET)
SWITCH, TACTILE (DOWN)
TACTILE SWITCH (ZOOM W)
SWITCH, TACTILE (RIGHT)
< SENSOR >
SE401 1-476-807-31 SENSOR, ANGULAR VELOCITY (PITCH)
SE402 1-476-807-41 SENSOR, ANGULAR VELOCITY (YAW)
************************************************************
SY-127 BOARD, COMPLETE
**********************
Electrical parts list of the SY-127 board are not
shown.
Pages from 5-14 to 5-18 are not shown.
DSC-H1
5-13E
SY-127
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar
Printing a text
Reversing the screens displayed once
1. Click the Print button
.
2. Specify a printer, print range, number of copies, and other options, and then click [OK].
• To reverse the previous screens (operation) one by one, click
.
the
• To advance the reversed screens (operation) one by one, click
the
.
Application of printing:
To set a range to be printed within a page, select the graphic
and drag on the page to enclose a range to
selection tool
be printed, and then click the Print button.
Application to the Service Manual:
This function allows you to go and back between circuit diagram and printed circuit board diagram, and accordingly it
will be convenient for the voltage check.
Finding a text
1. Click the Find button
.
2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary)
Application to the Service Manual:
To execute “find” from current page toward the previous pages,
select the check box “Find Backward” and then click the
“Find”.
Moving with link
1. Select either palm tool
, zoom tool
, text selection tool
, or graphic selection tool
.
2. Place the pointer in the position in a text where the link exists
(such as a button on cover and the table of contents page, or
blue characters on the removal flowchart page or drawing
page), and the pointer will change to the forefinger form
.
3. Then, click the link. (You will go to the link destination.)
Moving with bookmark:
Click an item (text) on the bookmark pallet, and you can move
can display the
to the link destination. Also, clicking
hidden items.
(To go back to original state, click
)
3. Open the find dialog box again, and click the [Find Again] and
you can find the matched character strings displayed next.
(Character strings entered previously are displayed as they are
in the text box.)
Application to the Service Manual:
The parts on the drawing pages (block diagrams, circuit diagrams, printed circuit boards) and parts list pages in a text
can be found using this find function. For example, find a
Ref. No. of IC on the block diagram, and click the [Find Again]
continuously, so that you can move to the Ref. No. of IC on
the circuit diagram or printed circuit board diagram successively.
Note: The find function may not be applied to the Service
Manual depending on the date of issue.
Zooming or rotating the screen display
“Zoom in/out”
• Click the triangle button in the zoom control box to select the
display magnification. Or, you may click
ing in or out.
or
for zoom-
Switching a page
• To move to the first page, click the
.
• To move to the last page, click the
.
• To move to the previous page, click the
• To move to the next page, click the
.
.
“Rotate”
• Click rotate tool
, and the page then rotates 90 degrees each.
Application to the Service Manual:
The printed circuit board diagram you see now can be changed
to the same direction as the set.
Reverse
987688031.pdf
Revision History
Ver.
Date
1.0
2005.04
DSC-H1
History
Official Release
Contents
—
S.M. Rev.
issued
—