Download SERVICE MANUAL

TopPage
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
SERVICE MANUAL
No. S60G440LE812E
LCD COLOUR TELEVISION
LC-40LE812E
LC-46LE812E
LC-40LX812E
LC-46LX812E
MODELS
LC-40LE822E
LC-46LE822E
LC-52LE822E
LC-40LU822E
LC-46LU822E
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original
condition and only parts identical to those specified should be used.
This Service Manual covers the differences from LC-40/46LE810E, LC-40/46LX810E and LC-40/46/52LE820E, LC-40/
46LU820E. For other technical information, refer to the LC-40/46LE810E, LC-40/46LX810E (No. S30E940LE810E) Service Manual and LC-40/46/52LE820E, LC-40/46LU820E (No. S30F240LE820E) Service Manual.
CONTENTS
OUTLINE AND DIFFERENCES FROM BASE MODEL
OUTLINE.............................................................i
DIFFERENCES FROM BASE MODEL
(LC-40LE812E/LX812E) .....................................i
DIFFERENCES FROM BASE MODEL
(LC-46LE812E/LX812E) .....................................i
DIFFERENCES FROM BASE MODEL
(LC-40LE822E/LU822E) ....................................ii
DIFFERENCES FROM BASE MODEL
(LC-46LE822E/LU822E) ....................................ii
DIFFERENCES FROM BASE MODEL
(LC-52LE822E) ................................................. iii
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION ..........................................................iv
Precautions for using lead-free solder ...............v
End of life disposal ............................................vi
OUTLINE
MAJOR SERVICE PARTS ............................... vii
CHAPTER 1. SPECIFICATIONS
[1] SPECIFICATIONS ......................................... 1-1
CHAPTER 2. OPERATION MANUAL
[1] OPERATION MANUAL .................................. 2-1
CHAPTER 3. ADJUSTMENT
[1] ADJUSTMENT PROCEDURE ......................3-1
CHAPTER 4. TROUBLESHOOTING TABLE
[1] TROUBLESHOOTING TABLE ......................4-1
CHAPTER 5. MAJOR IC INFORMATIONS
[1] MAJOR IC INFORMATIONS .........................5-1
CHAPTER 6. OVERALL WIRING/BLOCK DIAGRAM
[1] OVERALL WIRING DIAGRAM
(LC-40LE812E/LX812E)................................6-1
[2] OVERALL WIRING DIAGRAM
(LC-46LE812E/LX812E)................................6-2
[3] OVERALL WIRING DIAGRAM
(LC-40LE822E/LU822E)................................6-3
[4] OVERALL WIRING DIAGRAM
(LC-46LE822E/LU822E)................................6-4
[5] OVERALL WIRING DIAGRAM
(LC-52LE822E)..............................................6-5
[6] SYSTEM BLOCK DIAGRAM
(LC-40/46LE812E, LC-40/46LX812E) ...........6-6
[7] SYSTEM BLOCK DIAGRAM
(LC-40/46/52LE822E, LC-40/46LU822E) .........6-7
Parts Guide
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
LC-40LE812E
Service Manual
OUTLINE AND DIFFERENCES FROM BASE MODEL
OUTLINE
This Service Manual covers the differences from LC-40/46LE810E, LC-40/46LX810E and LC-40/46/52LE820E, LC-40/46LU820E.
For other technical information, refer to the LC-40/46LE810E, LC-40/46LX810E (No. S30E940LE810E) Service Manual and LC-40/46/52LE820E,
LC-40/46LU820E (No. S30F240LE820E) Service Manual.
DIFFERENCES FROM BASE MODEL (LC-40LE812E/LX812E)
LC-40LE810E/LX810E
(No. S30E940LE810E)
LC-40LE812E/LX812E
(No. S60G440LE812E)
PRINTED WIRING BOARD ASSEMBLIES
N
MAIN Unit
N
R/C, LED Unit
N
ICON Unit
N
TOUCH SENSOR Unit
N
POWER/LED CONTROL Unit
N
LCD CONTROL Unit
DKEYDF455FM03
DUNTKF494FM02
DUNTKF493FM03
RUNTKA692WJQZ
RUNTKA685WJQZ
RUNTK4512TPZC
LCD PANEL
N
40" LCD Panel Module Unit
R1LK400D3LWF2Y
Ref No.
Description
Interchangeability
Note
DKEYDF455FM06
←
←
←
←
←
—
—
—
—
—
Changed
No change
No change
No change
No change
No change
←
—
No change
Interchangeability
Note
CABINET AND MECHANICAL PARTS
Please refer to a Parts Guide
SUPPLIED ACCESSORIES
Please refer to a Parts Guide
PACKING PARTS (NOT REPLACEMENT ITEM)
Please refer to a Parts Guide
DIFFERENCES FROM BASE MODEL (LC-46LE812E/LX812E)
LC-46LE810E/LX810E
(No. S30E940LE810E)
LC-46LE812E/LX812E
(No. S60G440LE812E)
PRINTED WIRING BOARD ASSEMBLIES
N
MAIN Unit
N
R/C, LED Unit
N
ICON Unit
N
TOUCH SENSOR Unit
N
POWER/LED CONTROL Unit
N
LCD CONTROL Unit
DKEYDF455FM03
DUNTKF494FM02
DUNTKF493FM03
RUNTKA692WJQZ
RUNTKA686WJQZ
RUNTK4437TPZE
DKEYDF455FM06
←
←
←
←
←
—
—
—
—
—
Changed
No change
No change
No change
No change
No change
LCD PANEL
N
46" LCD Panel Module Unit
R1LK460D3LWA2Y
←
—
No change
Ref No.
Description
CABINET AND MECHANICAL PARTS
Please refer to a Parts Guide
SUPPLIED ACCESSORIES
Please refer to a Parts Guide
PACKING PARTS (NOT REPLACEMENT ITEM)
Please refer to a Parts Guide
Interchangeability
A:
Completely interchangeable
OLD = NEW
C:
Interchangeable from
NEW to OLD
NEW ψ OLD
B:
Interchangeable from
OLD to NEW
OLD ψ NEW
D:
Not interchangeable
NEW X OLD
i
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
DIFFERENCES FROM BASE MODEL (LC-40LE822E/LU822E)
LC-40LE820E/LU820E
(No. S30F240LE820E)
LC-40LE822E/LU822E
(No. S60G440LE812E)
PRINTED WIRING BOARD ASSEMBLIES
N
MAIN Unit
N
R/C, LED Unit
N
ICON Unit
N
LOGO Unit
N
TOUCH SENSOR Unit
N
POWER/LED CONTROL Unit
N
LCD CONTROL Unit
DKEYDF455FM01
DUNTKF494FM02
DUNTKF493FM03
DUNTKF493FM04
RUNTKA690WJQZ
RUNTKA685WJQZ
RUNTK4512TPZC
LCD PANEL
N
40" LCD Panel Module Unit
R1LK400D3LWF0Y
Ref No.
Description
Interchangeability
Note
DKEYDF455FM07
←
←
←
←
←
←
—
—
—
—
—
—
Changed
No change
No change
No change
No change
No change
No change
←
—
No change
Interchangeability
Note
CABINET AND MECHANICAL PARTS
Please refer to a Parts Guide
SUPPLIED ACCESSORIES
Please refer to a Parts Guide
PACKING PARTS (NOT REPLACEMENT ITEM)
Please refer to a Parts Guide
DIFFERENCES FROM BASE MODEL (LC-46LE822E/LU822E)
LC-46LE820E/LU820E
(No. S30F240LE820E)
LC-46LE822E/LU822E
(No. S60G440LE812E)
PRINTED WIRING BOARD ASSEMBLIES
N
MAIN Unit
N
R/C, LED Unit
N
ICON Unit
N
LOGO Unit
N
TOUCH SENSOR Unit
N
POWER/LED CONTROL Unit
N
LCD CONTROL Unit
DKEYDF455FM01
DUNTKF494FM02
DUNTKF493FM03
DUNTKF493FM04
RUNTKA690WJQZ
RUNTKA686WJQZ
RUNTK4437TPZE
DKEYDF455FM07
←
←
←
←
←
←
—
—
—
—
—
—
Changed
No change
No change
No change
No change
No change
No change
LCD PANEL
N
46" LCD Panel Module Unit
R1LK460D3LWA0Y
←
—
No change
Ref No.
Description
CABINET AND MECHANICAL PARTS
Please refer to a Parts Guide
SUPPLIED ACCESSORIES
Please refer to a Parts Guide
PACKING PARTS (NOT REPLACEMENT ITEM)
Please refer to a Parts Guide
Interchangeability
A:
Completely interchangeable
OLD = NEW
C:
Interchangeable from
NEW to OLD
NEW ψ OLD
B:
Interchangeable from
OLD to NEW
OLD ψ NEW
D:
Not interchangeable
NEW X OLD
ii
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
DIFFERENCES FROM BASE MODEL (LC-52LE822E)
LC-52LE820E
(No. S30F240LE820E)
LC-52LE822E
(No. S60G440LE812E)
PRINTED WIRING BOARD ASSEMBLIES
N
MAIN Unit
N
R/C, LED Unit
N
ICON Unit
N
LOGO Unit
N
TOUCH SENSOR Unit
N
POWER/LED CONTROL Unit
N
LCD CONTROL Unit
DKEYDF455FM01
DUNTKF494FM02
DUNTKF493FM03
DUNTKF493FM04
RUNTKA690WJQZ
RUNTKA694WJQZ
RUNTK4512TPZC
LCD PANEL
N
52" LCD Panel Module Unit
R1LK520D3LWA0Y
Ref No.
Description
Interchangeability
Note
DKEYDF455FM07
←
←
←
←
←
←
—
—
—
—
—
—
Changed
No change
No change
No change
No change
No change
No change
←
—
No change
CABINET AND MECHANICAL PARTS
Please refer to a Parts Guide
SUPPLIED ACCESSORIES
Please refer to a Parts Guide
PACKING PARTS (NOT REPLACEMENT ITEM)
Please refer to a Parts Guide
Interchangeability
A:
Completely interchangeable
OLD = NEW
C:
Interchangeable from
NEW to OLD
NEW ψ OLD
B:
Interchangeable from
OLD to NEW
OLD ψ NEW
D:
Not interchangeable
NEW X OLD
iii
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
LC-40LE812E
SAFETY PRECAUTION
Service Manual
IMPORTANT SERVICE SAFETY PRECAUTION
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
„ WARNING
•
1. For continued safety, no modification of any circuit should be
attempted.
Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity or measure the AC voltage drop across the resistor.
•
Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
Any reading of 1.05 V peak (this corresponds to 0.7 mA peak AC.)
or more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
2. Disconnect AC power before servicing.
CAUTION:
FOR CONTINUED PROTECTION AGAINST A
RISK OF FIRE REPLACE ONLY WITH SAME
TYPE FUSE.
40 inch model: F7000, F7001 (3.15A/250V)
46/52 inch model: F7000, F7001 (5A/250V)
DVM
AC SCALE
„ BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
1.5k ohm
10W
Before returning the receiver to the user, perform the following
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
0.15 µF
TEST PROBE
4. Inspect all protective devices such as non-metallic control knobs,
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner.
•
Plug the AC cord directly into a 220~240 volt AC outlet.
•
Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground.
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have
special safety-related characteristics.
For continued protection, replacement parts must be identical to those
used in the original circuit.
These characteristics are often not evident from visual inspection, nor
can protection afforded by them be necessarily increased by using
replacement components rated for higher voltage, wattage, etc.
The use of a substitute replacement parts which do not have the same
safety characteristics as the factory recommended replacement parts
shown in this service manual, may create shock, fire or other hazards.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by “
” and shaded areas in the Replacement Parts
List and Schematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
iv
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
Precautions for using lead-free solder
„Employing lead-free solder
•
“PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type of lead-free solder.
Example:
L F a/a
LFa
Indicates lead-free solder of tin, silver and copper.
Indicates lead-free solder of tin, silver and copper.
„Using lead-free wire solder
•
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
„Soldering
•
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
•
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Part No.
ZHNDAi123250E
ZHNDAi126500E
ZHNDAi12801KE
Description
J
J
J
φ0.3mm 250g (1roll)
φ0.6mm 500g (1roll)
φ1.0mm 1kg (1roll)
Code
BL
BK
BM
v
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
End of life disposal
End of life disposal
vi
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
LC-40LE812E
OUTLINE
Service Manual
MAJOR SERVICE PARTS
„PWB UNIT
Ref No.
N
N
N
N
N
N
N
N
N
N
N
N
Parts Code
DKEYDF455FM06
DKEYDF455FM07
DUNTKF494FM02
DUNTKF493FM03
DUNTKF493FM04
RUNTKA690WJQZ
RUNTKA692WJQZ
RUNTKA685WJQZ
RUNTKA686WJQZ
RUNTKA694WJQZ
RUNTK4512TPZC
RUNTK4437TPZE
Description
MAIN Unit (LC-40/46LE812E, LC-40/46LX812E) (*1)
MAIN Unit (LC-40/46/52LE822E, LC-40/46LU822E) (*1)
R/C, LED Unit
ICON Unit
LOGO Unit (LC-40/46/52LE822E, LC-40/46LU822E)
TOUCH SENSOR Unit (LC-40/46/52LE822E, LC-40/46LU822E) (*2)
TOUCH SENSOR Unit (LC-40/46LE812E, LC-40/46LX812E)
POWER/LED CONTROL Unit (LC-40LE812E/LX812E, LC-40LE822E/LU822E)
POWER/LED CONTROL Unit (LC-46LE812E/LX812E, LC-46LE822E/LU822E)
POWER/LED CONTROL Unit (LC-52LE822E)
LCD CONTROL Unit (LC-40LE812E/LX812E/LE822E/LU822E, LC-52LE822E)
LCD CONTROL Unit (LC-46LE812E/LX812E/LE822E/LU822E)
NOTE: (*1) Replace MAIN Unit (DKEYDF455FM06, DKEYDF455FM07) in case of IC8401 or IC3302 failure.
(*2) TOUCH SENSOR Unit (RUNTKA690WJQZ) reuse will be impossible, once it is stuck on front cabinet and
exfoliates.
Therefore, please exchange of a TOUCH SENSOR Unit in the case of front cabinet exchange.
„OTHER UNIT
Ref No.
N
N
N
N
N
Parts Code
R1LK400D3LWF0Y
R1LK400D3LWF2Y
R1LK460D3LWA0Y
R1LK460D3LWA2Y
R1LK520D3LWA0Y
Description
40" LCD Panel Module Unit (LC-40LE822E/LU822E)
40" LCD Panel Module Unit (LC-40LE812E/LX812E)
46" LCD Panel Module Unit (LC-46LE822E/LU822E)
46" LCD Panel Module Unit (LC-46LE812E/LX812E)
52" LCD Panel Module Unit (LC-52LE822E)
„IC FOR EXCLUSIVE USE OF THE SERVICE
Ref No.
IC501
IC2002
Parts Code
RH-iXD108WJQZS
RH-iXC786WJNJQ
IC 24LC21AT-I/SN
IC R5F364A6NFB
Description
Q’ty
1
1
Description
Main Unit to LCD Control Unit (LW)
Main Unit to Power Unit (PL)
Main Unit to Power Unit (PD)
Main Unit to Power (LED Drive) Unit (LB)
Main Unit to R/C, LED Unit (RA)
Main Unit to Speaker (SP)
Main Unit to Icon Unit (RL) (LC-40/46/52LE822E, LC-40/46LU822E)
Main Unit to Woofer (SB)
Q’ty
1
1
1
1
1
1
1
1
„SERVICE JIGS
Ref No.
N
N
N
N
N
N
N
N
Parts Code
QCNW-G616WJQZ
QCNW-G625WJQZ
QCNW-H184WJQZ
QCNW-H185WJQZ
QCNW-K594WJQZ
QCNW-K595WJQZ
QCNW-K596WJQZ
QCNW-K597WJQZ
vii
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
CHAPTER 1. SPECIFICATIONS
LC-40LE812E
Service Manual
[1] SPECIFICATIONS
Item
LCD COLOUR
TV (40 "/102 cm),
LC-40LE822E,
LC-40LU822E,
LC-40LE812E, LC40LX812E
LCD COLOUR
TV (46 "/117 cm),
LC-46LE822E,
LC-46LU822E,
LC-46LE812E, LC46LX812E
LCD COLOUR TV
(52 "/132 cm), LC52LE822E
LCD panel
102 cm (40 ")
X-Gen panel
117 cm (46 ")
X-Gen panel
132 cm (52 ")
X-Gen panel
Resolution
1,920 x 1,080 x 4 dots
Video colour system
TV function
TV-standard
Receiving
channel
PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
Analogue
CCIR (B/G, I, D/K, L/L')
Digital
DVB-T (2K/8K OFDM), DVB-C, DVB-S/S2
VHF/UHF
IR A ch-E69 ch (Digital), E2-E69 ch, F2-F10 ch, I21-I69 ch, IR A-IR J ch
CATV
Hyper-band, S1-S41 ch
Satellite
950-2150 MHz* 3
TV-tuning system
Auto Preset 999 ch (non-Nordic [DTV]), Auto Preset 9999 ch (Nordic [DTV]),
Auto Preset 99 ch (ATV), Auto Label, Auto Sort, Auto Preset 9999 ch (SAT)
STEREO/BILINGUAL
NICAM/A2
Audio amplifier
10 W x 2/15 W x 1
Speaker
(234 mm x 22 mm) x 2/Ø 110 mm
Terminals
Antenna
UHF/VHF 75
RS-232C
D-Sub 9 pin male connector
EXT 1
SCART (AV input, Y/C input, RGB input, TV output)
EXT 2
RCA pin (AV input/AUDIO L/R)
EXT 3
15 pin mini D-sub
HDMI 1 (EXT 4)
HDMI (ARC)
HDMI 2 (EXT 5)
HDMI
HDMI 3 (EXT 6)
HDMI
HDMI 4 (EXT 7)
HDMI
USB
USB
Din type (analogue & digital), Satellite 75
ETHERNET (10/100)
Home network connector (only the 822 model series)
HDMI 2/EXT 3 AUDIO (L/R)
Ø 3.5 mm jack*1
DIGITAL AUDIO OUTPUT
Optical S/PDIF digital audio output
C. I. (Common Interface)
EN50221, R206001, CI Plus specification
OUTPUT/Headphones
RCA pin (AUDIO R/L)/Ø 3.5 mm jack (audio output)
F type (DVB-S/S2)
OSD language
Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek,
Hungarian, Italian, Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian,
Slovak, Slovene, Spanish, Swedish, Turkish, Ukrainian
Power requirement
AC 220-240 V, 50 Hz
Power consumption (method
IEC62087)
822 models
127 W (0.2 W standby* 2) 147 W (0.2 W standby*2) 159 W (0.2 W standby*2)
812 models
127 W (0.2 W standby* 2) 147 W (0.2 W standby*2)
Weight
822 models
19.5 kg (without stand),
23.5 kg (with stand)
24.5 kg (without stand),
30.0 kg (with stand)
812 models
16.0 kg (without stand),
19.5 kg (with stand)
20.5 kg (without stand),
26.0 kg (with stand)
Operating temperature
*1
*2
*3
30.0 kg (without stand),
35.0 kg (with stand)
0 °C to + 40 °C
The HDMI 2 and EXT 3 terminals can both use the same audio input terminal.
Standby power consumption applies when the TV is set to not receive EPG data.
The satellite channel's frequency may vary according to satellites and antennas.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product
improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be
some deviations from these values in individual units.
1–1
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
CHAPTER 2. OPERATION MANUAL
LC-40LE812E
Service Manual
[1] OPERATION MANUAL
TV (front view)
1
2
1
2
3
4
5
6
3
4
5
6
7
8
7
VOL /
(Volume buttons)
CH /
(Programme [channel]
buttons)
INPUT
(Input source button)
MANU
(Menu button)
POWER (Power button)
OPC sensor
Remote control sensor
Illumination LED
8
TV (rear view)
6
1
2
3
4
5
*1
7
8
9
6
7
8
10
9
*2
11
12
13
14
15
*2
*3
10
11
12
13
14
15
16
17
Antenna terminal
Satellite antenna terminal
EXT 1 (RGB) terminal
RS-232C terminal
DIGITAL AUDIO OUTPUT
terminal
USB terminal
ETHERNET (10/100) terminal
OUTPUT (Headphones/AUDIO
(L/R)) terminal
EXT 2 (AV IN/VIDEO/AUDIO (L/R))
terminal
EXT 3 (ANALOGUE RGB (PC/
COMPONENT)) terminal
HDMI 2/EXT 3 AUDIO (L/R) jack
HDMI 1 (HDMI/ARC) terminal
HDMI 2 (HDMI) terminal
HDMI 3 (HDMI) terminal
HDMI 4 (HDMI) terminal
C.I. (COMMON INTERFACE) slot
MAIN POWER switch
WARNING
Excessive sound pressure from earphones
and headphones can cause hearing loss.
Do not set the volume at a high level.
Hearing experts advise against extended
listening at high volume levels.
16
*3
17
*1
1
2
3
4
5
This terminal is not available for the 812 model series.
The HDMI 2 and EXT 3 terminals can both use the same audio input terminal (HDMI 2/EXT 3 AUDIO (L/R)). However, the proper item
must be selected in the Audio select menu.
When the MAIN POWER switch is turned off ( ), the amount of electric power consumed will be reduced to 0.01 W or less. However,
unlike when unplugging the AC cord, the power is not completely disconnected.
2–1
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
CHAPTER 3. ADJUSTMENT
LC-40LE812E
Service Manual
[1] ADJUSTMENT PROCEDURE
1. Adjustment method after PWB and/or IC replacement due to repair
The unit is set to the optimum at the time of shipment from the factory.
If any value should become improper or any adjustment is necessary due to the part replacement, make an adjustment according to the following procedure.
1. Procure the following units in order to replace the main unit
MAIN UNIT:
DKEYDF455FM06 (LC-40/46LE812E, LC-40/46LX812E)
DKEYDF455FM07 (LC-40/46/52LE822E, LC-40/46LU822E)
NOTE: [Caution when replacing ICs in the main unit (IC501, IC2002)]
The above ICs are EEPROMs storing the EDID data of PC, and Monitor microcomputer.
Before replacing the relevant part, procure the following parts in which the data have been rewritten.
IC501
IC2002
RH-iXD108WJQZS
RH-iXC786WJNJQ
PC EDID
Monitor microcomputer
NOTE: [Caution when replacing ICs in the main unit (IC8401, IC3302)]
When replacing either IC8401 or IC3302, exchange MAIN units for DKEYDF455FM06/07
Each part should not be individually exchanged.
IC8401
IC3302
RH-iXC147WJQZQ
RH-iXC951WJQZQ
Flash
Main CPU
NOTE: HDMI ROM Writing
After replacing IC1504, execute “HDMI EDID WRITE” on the page 5/21
Please execute it after checking MODEL NAME & INCH SIZE. are correct.
IF MODEL NAME & INCH SIZE. are not correct, set them previously. (Refer to 2)
The ROM data based on information of MODEL NAME & INCH SIZE
1) Enter the process adjustment mode in TV.
2) Use the cursor keys ( / ) and CH keys (
/
) of R/C to select the item [HDMI EDID WRITE] on the page 5/21.
2. After replacing the LCD panel or LCD control/MAIN UNIT, check MODEL NAME in the following procedure.
1) Enter the process adjustment mode in TV.
2) Use the cursor keys ( / ) and CH keys (
/
) of R/C to select the item [MODEL NAME] on the page 21/21.
3) Verify that the Model name is displayed.
4) If the Model name doesn't match, select the values of the Model name with the VOL keys (+/-).
5) After selection in Step 4), press the OK key, and it is completed with OK displayed.
6) Use the cursor keys ( / ) and CH keys (
/
) of R/C to select the item [PANEL_SIZE] on the page 21/21.
7) Verify that the panel size is displayed.
8) If the size doesn't match, select the values of the panel size with the VOL keys (+/-).
9) After selection in Step 8), press the OK key, and it is completed with OK displayed.
3. After replacing the LCD panel or LCD control PWB, adjust the VCOM in the following procedure.
1) Enter the process adjustment mode.
2) Use the cursor keys ( / ) and CH keys (
/
) of R/C to select the item [VCOM ADJ] on the page 10/21.
3) Press the OK key to verify that the adjustment pattern is displayed.
4) Use VOL keys (+/-) of R/C to adjust the flicker in the center of the screen to minimum.
5) When the optimal state is achieved in Step 4, press the OK key to turn the pattern to OFF.
3–1
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
2. Notes of Touch sensor unit (LC-40/46/52LE822E, LC-40/46LU822E)
Touch sensor unit (RUNTKA690WJQZ) is fixed directly in the module glass.
The unit cannot never be recycled when exfoliated from the module glass.
Therefore, please exchange the touch sensor units when the module glass is changed.
Please note the adhesion and mixing of dust for the module glass when the module glass and the touch sensor unit are exchanged.
Module glass
40inch: CPNLHA019WE11
46inch: CPNLHA020WJ11
52inch: CPNLHA021WJ11
3. Method of shuts down for Power supply
Please execute the following procedures to shut down Power supply from the state of normal operation.
1) Keep touching the power supply key on the set for 5 seconds from the state of watching.
*
The screen disappears when power supply key is touched, but Keep pushing the power supply key.
2) A central icon lights between 500ms when the power supply shuts down.
Please separate the finger from the power supply key when lighting of a central icon is confirmed
4. Entering and exiting the adjustment process mode
Please execute the following procedures to enter the adjustment process mode when the power supply shuts down.
1) While holding down the “VOL (-)” and “INPUT” keys on the set at once, touch the power supply key on the set.
Please separate the fingers from key on the set when boot-up is confirmed with lighting of a central icon etc.
After a while, The letter “K” appears on the screen. This state is in Inspection mode.
2) Next, hold down the “VOL (-)” and “CH (
)” keys on the set at once.
Multiple lines of blue characters appearing on the screen indicate that the set is now in the adjustment Process mode.
If you fail to enter the adjustment process mode (the display is the same as normal startup), retry the procedure.
3) To exit the adjustment process mode after the adjustment is done, unplug the AC power cord to force off the power.
(When the power is turned off with the remote controler, once unplug the AC power cord and plug it in again. In this case, wait for 10 seconds or
so after unplugging.)
CAUTION: Use due care in handling the information described here lest the users should know how to enter the adjustment process mode.
If the settings are tampered with in this mode, unrecoverable system damage may result.
5. Remote controler key operation and description of display in adjustment process mode.
1. Key operation
Remote controler key
CH keys (
/
)
VOL keys (+/-)
Cursor ( / )
Cursor ( / )
INPUT
OK
RETURN
Main unit key
CH (
/
)
VOL (+/-)
—
—
INPUT
—
—
Remote controler key Main unit key Function
Moving an item (line) by one (UP/DOWN)
Changing a selected item setting (+1/-1)
Turning a page (PREVIOUS/NEXT)
Changing a selected line setting (+10/-10)
Input source switching (toggle switching) (TV→EXT1~9, USB)
Executing a function
Returning to a present page
Input mode is switched automatically when relevant adjustment is started so far as the necessary input signal is available.
3–2
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
6. Description of display
(1) Present page / number of total pages
(4) Inducing display
(3) Present colour system
(2) Input that has been selected now
(5) Inch setting and Model name display
1/21
INPUT1
MAIN Version
BOOT Version
Monitor Version
T-CON Version/LED CON Version
CPLD Version
CI+INFO/SECURE BOOT
FRC-N Auto Script Version
TCON Master/Slave Serial Version
TOUCH SENSOR UCON VERSION
LAMP ERROR
MONITOR ERR CAUSE
NORMAL STANDBY CAUSE
ERROR STANDBY CAUSE
AUTO
Description
Present page/number of total pages
Input that has been selected now
Present colour system
Inducing display
Inch setting and Model name display
Item name
Parameter
xxxxx
1.00 (E 2009/**/** )
xxxxxxx
xxxxxxx
xxxxxxxx/xxxx
xxxxxxx
xxxxx/YES
xxxxxxx
xxxxxxx
xxxxxxx
0
1)xxxxxx 2)xxxxxx
3)xxxxxx 4)xxxxxx
0
0000
(7) Parameter
(6) Item name
No.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
EURO
Display specification
2char/2char Decimal Number mark.
TUNER/DTV/INPUT1/INPUT2/INPUT3/INPUT5/INPUT6/INPUT7
AUTO/N358/N443/PAL/SECAM/480i/580i/1080i/50 etc. ⋅⋅⋅
EUROPE
Inch setting and Model name display
Max. 30 char
Max. 60 char
3–3
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
7. Adjustment process mode menu
The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
Page
1/21
Line
Item
Description
1xxx (xxxxx)
xxxxxxx
xxxxxxx
xxxxxxxx/xxxx
xxxxxxx
xxxxx/YES
xxxxxxx
xxxxxxx
xxxxxxx
0
1) xxxxxx 2) xxxxxx
3) xxxxxx 4) xxxxxx
0
Remarks (adjustment detail, etc.)
1
2
3
4
5
7
8
9
10
11
12
MAIN Version
BOOT Version
Monitor Version
T-CON Version/LED CON Version
CPLD Version
CI+INFO/SECURE BOOT
FRC-N Auto Script Version
TCON Master/Slave Serial Version
TOUCH SENSOR UCON VERSION
LAMP ERROR
MONITOR ERR CAUSE
13
NORMAL STANDBY CAUSE
14
ERROR STANDBY CAUSE
1
2
INDUSTRY INIT
INDUSTRY INIT (-Public)
Enter
OFF
3
4
5
6
7
8
9
10
11
12
13
PUBLIC MODE
Center Acutime
RESET
Backlight Acutime
RESET
LAMP ERROR RESET
ADJ PARAM SET
VIC XPOS
VIC YPOS
VIC SIGNAL TYPE
VIC READ
OFF
—
OFF
—
OFF
OFF
Enter
0
0
MAIN
OFF
1
2
3
4
5
6
7
8
9
TUNER ADJ
PAL+TUNER ADJ
TUNER ADJ (SMPTE)
PAL+TUNER ADJ (SMPTE)
TUNER ADJ (SMPTE CH57)
PAL+TUNER ADJ (SMPTE CH57)
TUNER CONTRAST A_GAIN
TUNER CONTRAST D_GAIN
TUNER CONTRAST OFFSET
Enter
Enter
Enter
Enter
Enter
Enter
16
2073
256
TUNER auto adjustment execution
PAL TUNER auto adjustment execution
TUNER auto adjustment execution (SMPTE)
PAL TUNER auto adjustment execution (SMPTE)
TUNER auto adjustment execution (SMPTE CH57)
PAL TUNER auto adjustment execution (SMPTE CH57)
TUNER signal level adjustment
TUNER signal level adjustment
TUNER signal level adjustment
1
2
3
4
5
6
7
8
9
10
11
12
PAL ADJ
SECAM ADJ
N358 ADJ
PAL CONTRAST A_GAIN
PAL CONTRAST D_GAIN
PAL CONTRAST OFFSET
SECAM CONTRAST A_GAIN
SECAM CONTRAST D_GAIN
SECAM CONTRAST OFFSET
N358 CONTRAST A_GAIN
N358 CONTRAST D_GAIN
N358 CONTRAST OFFSET
Enter
Enter
Enter
14
2149
255
14
2123
256
14
2192
255
PAL adjustment
SECAM adjustment
N358 adjustment
PAL contrast adjustment
PAL contrast adjustment
PAL contrast adjustment
SECAM contrast adjustment
SECAM contrast adjustment
SECAM contrast adjustment
N358 contrast adjustment
N358 contrast adjustment
N358 contrast adjustment
0000
Main software version
BOOT Version.
Monitor software version
T-CON/H.264 Version
CPLD Version.
CI+ Key Information/SECURE BOOT
Number of termination due to lamp error.
Last error standby cause.
Situation that became standby at the end.
(Excluding the error)
Error standby cause
2/21
Initialization to factory settings execution.
Initialization to factory settings execution.
(Public mode is excluded)
Public mode ON/OFF setting
Main operating hours.
Main operating hours reset.
Backlight operating hours.
Backlight operating hours reset.
Lamp error reset.
ADJ PARAM SET
X-coordinate setting for VIC READ
Y-coordinate setting for VIC READ
Signal type setting for VIC READ
Picture level acquisition function
(Level appears in green on the upper right)
3/21
4/21
3–4
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
Page
5/21
Line
Item
Description
Remarks (adjustment detail, etc.)
Enter
Enter
Enter
OFF
Enter
Size 1
HDMI CEC test
Reading inspection of USB memory terminal
HDMI EDID WRITING
MONITOR Temperature/OPC Acquisition tool.
Reset of standby cause
SD CARD TEST
(*This item is LC-40/46/52LE822E, LC-40/46LU822E only)
SD CARD REC SIZE
(*This item is LC-40/46/52LE822E, LC-40/46LU822E only)
SD CARD RESET
(*This item is LC-40/46/52LE822E, LC-40/46LU822E only)
1
2
3
4
5
6
HDMI CEC TEST
INSPECT USB TERM
HDMI EDID WRITE
MONIDATA READ [TEMP/OPC]
CAUSE RESET
SD CARD TEST
7
SD CARD REC SIZE
8
RESET
OFF
1
2
3
4
5
6
7
COMP15K ALL ADJ
COMP15K MAIN Y GAIN
COMP15K MAIN CB GAIN
COMP15K MAIN CR GAIN
COMP15K Y OFFSET
COMP15K CB OFFSET
COMP15K CR OFFSET
Enter
141
150
150
64
128
128
Component 15K picture level adjustment
Y GAIN adjustment value
Cb GAIN adjustment value
Cr GAIN adjustment value
Y OFFSET adjustment value
Cb OFFSET adjustment value
Cr OFFSET adjustment value
1
2
3
4
5
6
7
HDTV ADJ
HDTV Y GAIN
HDTV CB GAIN
HDTV CR GAIN
HDTV Y OFFSET
HDTV CB OFFSET
HDTV CR OFFSET
Enter
141
150
150
64
128
128
HDTV video level adjustment
HDTV Y GAIN adjustment value
HDTV Cb adjustment value
HDTV Cr adjustment value
HDTV Y OFFSET adjustment value
HDTV Cb OFFSET adjustment value
HDTV Cr OFFSET adjustment value
1
2
3
4
5
6
7
ANALOG PC ADJ
R OFFSET
G OFFSET
B OFFSET
R GAIN
G GAIN
B GAIN
Enter
64
64
64
44
44
44
DVI ANALOG video level adjustment
R CUTOFF adjustment value
G CUTOFF adjustment value
B CUTOFF adjustment value
R DRIVE adjustment value
G DRIVE adjustment value
B DRIVE adjustment value
1
2
3
4
5
6
7
SCART RGB ADJ
SCART R CUTOFF
SCART G CUTOFF
SCART B CUTOFF
SCART R GAIN
SCART G GAIN
SCART B GAIN
Enter
64
64
64
44
44
44
SCART RGB level adjustment
SCART R CUTOFF adjustment value
SCART G CUTOFF adjustment value
SCART B CUTOFF adjustment value
SCART R GAIN adjustment value
SCART G GAIN adjustment value
SCART B GAIN adjustment value
1
VCOM ADJ
0
Common bias adjustment
1
2
3
4
5
6
R GAIN (LO)
G GAIN (LO)
B GAIN (LO)
R GAIN (HI)
G GAIN (HI)
B GAIN (HI)
0
0
0
0
0
0
R DRIVE adjustment value
G DRIVE adjustment value
B DRIVE adjustment value
R DRIVE adjustment value
G DRIVE adjustment value
B DRIVE adjustment value
1
2
3
4
5
MONITOR TIME OUT
MONITOR MAX TEMP
MONITOR EEP READ/WRITE
MONITOR EEP ADR
MONITOR EEP DATA
1
2
3
4
5
LCD TEST PATTERN
LCD TEST PATTERN 1
LCD TEST PATTERN 2
LCD TEST PATTERN 3
LCD TEST PATTERN 4
xx
6/21
7/21
8/21
9/21
10/21
11/21
12/21
ON
45
WRITE
0x 0
0x 0
Monitor and the main communication time-out setting
MONITOR MAX temperature setting
MONITOR EEPROM READ/WRITE Setting/execution
MONITOR EEPROM arbitrary addressing
MONITOR EEPROM arbitrary data specification
13/21
OFF
OFF
OFF
OFF
OFF
3–5
Pattern with built-in LCD controler display
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
Page
14/21
Line
Item
Description
1
2
3
4
5
6
7
FRV-N Firmware Version
FRC-N Boot Script Version
FRC-N Device Version
TCON FPGA1 Serial Flash Version
TCON FPGA2 Serial Flash Version
TCON FPGA1 Config Rom Version
TCON FPGA2 Config Rom Version
1
2
3
4
5
6
7
8
9
10
POWER LED BRIGHTNESS
MENU LED BRIGHTNESS
INPUT LED BRIGHTNESS
CH UP LED BRIGHTNESS
CH DOWN LED BRIGHTNESS
VOL UP LED BRIGHTNESS
VOL DOWN LED BRIGHTNESS
LOGO LED BRIGHTNESS
ICON LED BRIGHTNESS
ICON LED BRIGHTNESS (STANDBY)
0
0
0
0
0
0
0
99
99
30
1
2
3
4
5
6
7
POWER KEY SENSITIVITY
MENU KEY SENSITIVITY
INPUT KEY SENSITIVITY
CH UP KEY SENSITIVITY
CH DOWN KEY SENSITIVITY
VOL UP KEY SENSITIVITY
VOL DOWN KEY SENSITIVITY
0
0
0
0
0
0
0
1
2
3
4
5
6
7
KEY STRENGTH GET MODE
POWER KEY STRENGTH
MENU KEY STRENGTH
INPUT KEY STRENGTH
CH UP KEY STRENGTH
CH DOWN KEY STRENGTH
VOL UP KEY STRENGTH
VOL DOWN KEY STRENGTH
1
2
3
READ/WRITE
SLAVE/ADDRESS
REGISTER ADDRESS
4
WRITE DATA
5
READ DATA
1
2
3
4
RF AGC BG
RF AGC DK
RF AGC I
RF AGC L/L'
1
2
3
4
5
6
ERROR STANDBY CAUSE 1
ERROR STANDBY CAUSE 2
ERROR STANDBY CAUSE 3
ERROR STANDBY CAUSE 4
ERROR STANDBY CAUSE 5
STANDBY CAUSE RESET
Remarks (adjustment detail, etc.)
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
xxxxx
15/21
16/21
17/21
Enter
18/21
READ
SLAVE0
0x 0
0x 0
0x 0
0x 0
0x 0
0x 0
Read/Write
Slave address
Register address
Writing data
Reading data
19/21
6
5
6
4
RF-AGC BG adjustment execution
RF-AGC DKG adjustment execution
RF-AGC I adjustment execution
RF-AGC L/L' adjustment execution
20/21
NO RECORD
NO RECORD
NO RECORD
NO RECORD
NO RECORD
OFF
3–6
ERROR STANDBY CAUSE
Reset stand by cause.
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
Page
21/21
Line
1
2
3
4
5
6
7
8
9
10
11
Item
Description
EEP SAVE
EEP RECOVER
MONITOR ERROR CAUSE RESET
MODEL NAME
PANEL SIZE
SHORT CHECK MODE
SHORT CHECK CURRENT
CURRENT SW
PRODUCT EEP ADR
PRODUCT EEP DATA
PRODUCT FACTORY
OFF
OFF
OFF
LE705
40
Enter
60
LOW
0x 0
0x 0
1
Remarks (adjustment detail, etc.)
Writing setting values to EEPROM.
Reading setting values from EEPROM.
Reset of monitor error cause
MODEL NAME
Panel size setting. (40/46/52)
Check LED Back light
Don't touch when serving (for producer of factory)
Don't touch when serving (for producer of factory)
Don't touch when serving (for producer of factory)
8. Special features
1. NORMAL STANDBY CAUSE (Page 1/21)
Display of a cause (code) of the last standby.
The cause of the last standby is recorded in EEPROM whenever it is possible.
Checking this code will be useful in finding a problem when you repair the troubled set.
2. EEP SAVE (Page 21/21)
Storage of EEP adjustment value
3. EEP RECOVER (Page 21/21)
Retrieval of EEP adjustment value from storage area.
4. MONITOR ERR CAUSE (Page 1/21)
Display of a cause (code) of Error from sub-Microcomputer.
The cause of Error is recorded in EEPROM whenever it is possible.
Checking this code will be useful in finding a problem when you repair the troubled set.
1) This displays Error code and time when the error occurred.
The latest error is displayed on “1)”
The error that happens ahead of “1)” is displayed on “2)”.
2) The character depends on the way how to acquire Time Information
T:
U:
B:
Time is acquired from digital broadcasting
This doesn't contain “Time offset” which is considered a time difference and Daylight-Saving Time, etc. ...
Time is acquired from analog broadcasting (teletext)
Accumulation time of Backlight
In the case that Time information cannot be acquired, “B” is displayed.
Example) In this example, it is shown that the error occurred 3 times.
1) 16 T07/01/01 12:03
2) 16 U01/01/01 04:07
3) 16 B00000004:11
4) 00 0000000000000
Error code: 16 (lamp error)
Time: 07/01/01 12:03
* It is latest Error.
* Time is acquired from digital broadcasting.
* Time is UTC which doesn't have Time offset.
Error code: 16 (lamp error)
Time: 07/01/01 04:07
* It is Error that happens ahead of “1)”.
* Time is acquired from analogue broadcasting.
Error code: 16 (lamp error)
Accumulation time: It is displayed that 4:11 have passed after Backlight driving.
* It is Error that happens ahead of “2)”.
No error (“00” shows that the error is not occurred.)
3–7
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
9. Lamp Error detection
1. Function
This LCD colour TV set incorporates a Lamp error detection feature that automatically turns off the power for safety under abnormal lamp or lamp
circuit conditions. If by any chance anything is wrong with the lamp or lamp circuit or if the lamp error detection feature is activated for some reason, the following will result.
1) The power is interrupted in about 500ms after it is turned on.
(A central icon on the front of the TV flash on and off.: ON for 400ms and OFF for 1600ms.).
2) If the above phenomenon 1) occurs 5 times, it becomes impossible to turn on the power.
(A central icon keep flashing on/off.)
2. Measures
1) Set the lamp error detection to OFF
Enter the adjustment process mode, referring to “4. Entering and exiting the adjustment process mode.”
The adjustment process mode can ignore “5 times count”, so If the above phenomenon 1) occurs 1~4 times, the lamp will go out.
If Lamp Error detection pin (6pin of LB: P9602) is “High” by a trouble with the lamp and lamp circuit, it can boot-up by the adjustment process
mode.
Please execute “Lamp Error detection off-mode”.
While holding down the “VOL (-)” and “CH (
)” keys on the set at once, touch the power supply key on the set.
After a central icon flash off, separate the fingers from key on the set.
Touch the power supply key on the set again, so the power will boot-up.
Then, you can check the operation to see if the lamp and lamp circuit are in trouble.
If you fail boot-up, retry the procedure.
2) Resetting the lamp error count
After the lamp and lamp circuit are improved from a trouble, reset the lamp error count.
(Because the power cannot be turned on, if a lamp error is detected 5 consecutive times)
a) Enter the adjustment process mode, referring to “4. Entering and exiting the adjustment process mode.”
b) Using the cursor ( / ) key, move to the cursor to [LAMP ERROR RESET], Line 8 on adjustment process mode service page 2/21.
c) With the cursor ( / ) keys, select the [LAMP ERROR RESET] value.
Finally press the cursor (OK)., the count is reset.
Check LAMP ERROR Count on adjustment process mode Page 2/21.
Table of contents of adjustment process mode Page 2/21
INDUSTRY INIT
INDUSTRY INIT (-Publicl)
Public MODE
Center Acutime
RESET
Backlight Acutime
RESET
LAMP ERROR RESET
ADJ PARAM SET
VIC XPOS
VIC YPOS
VIC SIGNAL TYPE
VIC READ
Enter
OFF
OFF
OFF
OFF
OFF
Enter
Resetting to "0"
0
0
MAIN
OFF
3–8
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
10. Public Mode
1. Starting the Public Mode
•
There are two following ways to display the PUBLIC Mode setting screen.
1) Method of needing password
a) Turn off the power, refer to “3. Method of shuts down for Power supply”
b) While holding down the “INPUT” and “Volume (+)” keys on the set at once, touch the power supply key on the set.
Please separate the finger from the power supply key when boot-up is confirmed with lighting of a central icon etc.
After a while, value of Public Mode appears on the screen.
c) Display the Pass Word input screen.
Public Mode
Public Mode
Public Mode
Operation procedure
•
The initial input position is the digit at the left end.
•
For the numeric keys “0” to “9” of R/C, key input is accepted.
Input of the other keys is prohibited.
•
Change “—” to “ * ” by inputting the numeric key at the input position, and shift the input position rightward one digit.
•
When three digits are completely input, the Pass Word is judged.
d) Check the Pass Word by inputting three digits.
If the Pass Word “0” “2” “7”, it shifts to the PUBLIC Mode setting screen.
In another case, the screen is erased, and it operates in the ordinary mode.
2. Exiting the Public Mode Setting screen
•
There are two following ways to exit the Public Mode setting screen.
1) Turn off the power.
2) Select “Execution” in the PUBLIC_Mode to execute it.
Activate the restart under the set content.
Here, the START input SOURCE setting is excluded since this item is referred to only when the power is turned on.
3. Set value of the Public Mode
•
When the shipment setting is done, a set each value in Public Mode is initialized.
(PUBLIC MODE in the process mode Setting of a flag is also initialized)
•
Separately, the shipment beginnings when all except for each set value in Public Mode is initialized are provided for a process mode.
(INDUSTRY INIT (-Public))
•
Only when turning on the PUBLIC MODE item, each setting is effective.
•
After it decides it with EXECUTE, it AC OFF/ON it to reflect a set value.
3–9
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
4. Basic operation in the Public Mode
Vol (+/-) or Cursor ( / )
CH (
/
) or Cursor ( / )
Decision (ok)
Change or execution of the set value.
Movement to the selected item.
Execution (Used by the items “Execution” and “RESET”.)
Public Mode setting screen.
Public Mode
POWER ON FIXED
SHUT DOWN MODE
MAXIMUM VOLUME
VOLUME FIXED
VOLUME FIXED LEVEL
RC BUTTON
PANEL BUTTON
MENU BUTTON
AV POSITION FIXED
ON SCREEN DISPLAY
INPUT MODE START
INPUT MODE FIXED
LOUD SPEAKER
RC PATH THROUGH
232C POWON
PUBLIC MODE
RESET
EXECUTE
[VARIABLE]
[NORMAL]
[60]
[VARIABLE]
[20]
[RESPOND]
[RESPOND]
[RESPOND]
[VARIABLE]
[YES]
[NORMAL]
[VARIABLE]
[ON]
[OFF]
[DISABLE]
[ON]
5. Operation after “RESET”
Select “RESET” in the PUBLIC Mode, and it operates as follows when it is executed (refer to the basic operation).
•
The set contents in the PUBLIC mode are initialized.
•
It does not exit the PUBLIC mode.
•
If “EXCUTE” is not executed, the content that does RESET is not reflected.
6. Setting items (* Item names and selective items are expressed in English.)
1) Power ON fixed [POWER ON FIXED]
Option
Default
Function
Key disabled when set
other than default
Remarks
“VARIABLE”, “FIXED_ALL”, “FIXED_BODYKEY” or “RCRESPOND” (loop enabled)
“VARIABLE”
• VARIABLE
: “POWER/RECEPTION” key on TV unit or remote control is enabled.
• FIXED_ALL“
: “POWER/RECEPTION” key on TV unit or remote control is disabled.
• FIXED_BODYKEY : only the “MAIN POWER” key on TV unit is disabled (the remote control is enabled).
• RC RESPOND
: the main unit’s POWER switch toggles between ON and Standby (the same operation by
the remote control).
• OFF TIMER (SLEEP) (* Only when setting to FIXED_ALL)
•
When selecting to “FIXED_ALL”, function related standby factors (see below) doesn't work. and not selecting
OFF TIMER (Sleep)
No operation OFF
No signal OFF (including the power management)
* These items does not exist according to the model.
If the power button is pressed in the ordinary mode in setting to “FIXED_ALL” and “FIXED_BODYKEY”, the caution is displayed for 5 seconds.
When power button on the main unit is pressed
When power button on R/C is pressed
No Power off by power button.
No Power off by remote control.
*
The OSD display is an example.
If another ODS is previously displayed, the status is reset (MENU or similar).
3 – 10
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
2) Instantaneous current shutdown setting in turning off the power [SHUT DOWN MODE]
Option
Default
Function
Remarks
“NORMAL” or “QUICK”
NORMAL
• This function decides whether scanning digital tuner is enabled or disabled when the power is standby.
NORMAL
: Scanning digital tuner is enabled when the power is standby.
QUICK
: Scanning digital tuner is disable
It is possible to put into the standby state instantaneously due to power off input, when the
power is standby.
Immediately, state is a complete standby.
In selecting “QUICK”, the function does not work for the following items (selection impossible.)
• ON TIMER, QUICK START, DIGITAL FIXED, etc.
* These items does not exist according to the model.
3) Volume maximum level [MAXIMUM VOLUME]
Option
Default
Function
Remarks
0~60 (loop disabled)
60
The volume cannot be increased more than the adjusted value (the main unit’s speaker only).
• When setting to 59 or less, only the figure is displayed in the normal mode; the volume bar is not displayed.
• The volume of the headphones is limited. or monitor output
• The setting is impossible when VOLUME FIXED is set to FIXED.
4) Volume fixed [VOLUME FIXED]
Option
Default
Function
Exception
Disabled key when setting
to FIXED
Remarks
“VARIABLE”, “FIXED”, “ACCTRL” or “AC/RCCTRL” (loop enabled)
“VARIABLE”
• VARIABLE
: The volume is not fixed.
• FIXED
: The volume is fixed to the value adjusted in the volume fixed level.
• AC CTRL
: The unit starts at the volume specified in the volume fixed level, when power is turned on in
the case of the AC-ON only.
• AC/RC CTRL
: The unit starts at the volume specified in the volume fixed level, when power is turned on in
any case. (AC→ON, remote control→ON, main unit's key→ON)
• In the adjustment process, the volume can be set to any level regardless of this setting.
• VOLUME UP/DOWN [both remote control and main unit]
• MUTE
• [MAXIMUM VOLUME] has priority to [VOLUME FIXED]
* When setting to FIXED, Maximum volume is fixed.
• The volume of the headphones is fixed.
• When setting to “FIXED”, the volume is not displayed in operating Disabled key
• In menu operation, the main unit's keys (Vol (+/-)) are enabled.
5) Volume fixed level [VOLUME FIXED LEVEL]
Option
Default
Function
Exception
Remarks
0~60 (loop disabled)
20
The volume is fixed to the adjusted value (the main unit’s speaker only).
• In the adjustment process, the volume can be set to any level regardless of this setting.
• When [VOLUME FIXED] is set to “VARIABLE”, the setting cannot be changed.
6) Remote control operation [RC BUTTON]
Option
Default
Function
Exception
Remarks
“RESPOND”, “NORESPOND” or “LIMITED” (loop enabled)
“RESPOND”
The operation of the remote control’s keys is set.
RESPOND
: the remote control’s keys in the normal state are enabled.
NO RESPOND
: the remote control’s keys in the normal state are disabled.
The POWER key (RECEPTION/STANDBY key) is also disabled.
LIMITED
: only a part of keys (CHANNEL, etc.) is enabled and other keys are disabled.
• In the adjustment process mode, inspection mode are enabled regardless of this setting.
• All the keys are enabled regardless of this setting while entering the adjustment process mode, inspection mode
or Public Mode setting screen.
The enable keys when setting to “LIMITED” are depended on keys of controler for Public.
It is different according to Model.
3 – 11
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
7) Main Unit Operation [PANEL BUTTON]
Option
Default
Function
Exception
“RESPOND” or “NORESPOND” (loop enabled)
“RESPOND”
• RESPOND
: The main unit’s keys are enabled.
• NO RESPOND
: The main unit’s keys are disabled excluding the POWER key (RECEPTION/STANDBY
key).
• The start operation in the adjustment process mode, inspection mode are enabled regardless of this setting.
• All the keys are enabled regardless of this setting while entering the adjustment process mode, inspection mode
or Public Mode setting screen.
• For the models with the MENU key on the main unit, menu operation is possible regardless of the setting during
the initial setting when the power is turned on for the first time.
8) Menu operation [MENU BUTTON]
Option
Default
Function
Exception
Disabled key excluding
Menu key when setting to
not default
Remarks
“RESPOND” or “NO RESPOND” (loop enabled)
“RESPOND”
The MENU key on the main unit and remote control is decided whether it is enabled or disabled.
• RESPOND
: The menu key is enabled.
• NO RESPOND
: The menu key is disabled.
: The start operation in the adjustment process mode, inspection mode is enabled regardless of this setting.
: All the keys are enabled regardless of this setting while entering the process mode, inspection mode or Public Mode setting screen.
All the direct transition keys to menu display (AUTO PRESET, MANUAL MEMORY and others)
* These keys does not exist according to the model.
When setting to “NO RESPOND”
• For the models with the MENU key on the main unit, menu operation is possible regardless of the setting while
the initial setting when the power is turned on for the first time
9) AV position fixed [AV POSITION FIXED]
Option
Default
Function
Remarks
“VARIABLE” or “FIXED” (loop enabled)
“VARIABLE”
• VARIABLE
: AV position is not fixed.
• FIXED
: AV position is fixed.
: The image/sound adjustment items in the menu are fixed in the selected state.
: When receiving “AV POSITION” of the remote control, only the actual state is displayed,
and setting is not changed.
• When receiving the sound select direct keys (AV POSITION key, OPC, DOLBY key, etc.), only the actual state is
displayed; no setting is changed.
* These keys does not exist according to the model.
• The settings for the Public mode are retained after the personal data is initialized, each item for the AV position
and image/sound adjustment are not initialized.
3 – 12
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
10)OSD display [ON SCREEN DISPLAY]
Option
Default
Function
Key which may be enabled
(Example of the confusing
key)
Disabled key when setting
to not default
Remarks
“YES”, “NO” or “LIMITED” (loop enabled)
“LIMITED” is looped only in case of need (destination).
“YES”
• YES
: OSD is displayed
• NO
: the following OSD is not displayed.
Registration, setting, adjustment menu, channel call, volume bar, and input select
• LIMITED
: only a part of OSD (CH call: “New Information” etc. ...) is not displayed.
• It is OK in the case that simple input select occure or the original state returns soon automatically.
•
•
•
When setting to “NO”, the keys which is related to visibility of the screen and sound cannot be used.
STILL IMAGE, SCREEN DISPLAY, OFF TIMER, AV POSITION, BRIGHTNESS SENSOR, SCREEN SIZE
SELECT, AUTO PRESET, MANUAL MEMORY, IMAGE SELECT, SOUND SELECT, LANGUAGE, Closed caution
* Disabled keys dependeds on the models.
When setting to “NO”,
ON TIMER (Watching reservation) is cleared.
OFF TIMER “SLEEP” is cleared.
* These items does not exist according to the model.
When setting to “NO”,
These Displays (Version-up, Public mode setting screen, Pass Word input screen of Public Mode,
the adjustment process mode, K mark of inspection mode) are enabled regardless of this setting.
11)Start mode [INPUT MODE START]
Option
Default
Function
Remarks
“NORMAL” or “Input source 1 (input selection or channel)” . . . (loop enabled)
“NORMAL”
which kinds of input source or channel is decided when the power turning on.
NORMAL
: the content of the last memory is followed.
• When setting to not Normal,
ON TIMER (Watching reservation) has priority.
• When setting to “NORMAL”, [INPUT MODE FIXED] is set to “VARIABLE”. and [INPUT MODE FIXED] is prohibited to select. (selection impossible.)
Example of option: “NORMAL”
“TVD (002TV)”, “INPUT1”, “INPUT2”, “INPUT3”, “HDMI1”, “HDMI2”, “HDMI3”, “HDMI4”.
12)Input fixed [INPUT MODE FIXED]
Option
Default
Function
Disabled key when setting
to “FIXED”
Remarks
“VARIABLE” “FIXED”, “ACCTRL” or “AC/RCCTRL” (loop enabled)
VARIABLE
VARIABLE
: If [INPUT MODE START] is set to Normal, input mode is not fixed.
FIXED
: when “INPUT MODESTART” is active, it is impossible to switch to another channel or input
source.
AC CTRL
: when “INPUT MODESTART” is active the unit starts at the input mode which is selected
when power is turned on in the case of the AC-ON only.
AC/RC CTRL
: when “INPUT MODESTART” is active the unit starts at the input mode which is selected
when power is turned on in any case (AC→ON, remote control→ON, main unit's key→ON)
CHANNEL (+/-), DIRECT CHANNEL buttons, FLASHBACK, INPUT SELECT, TV/VIDEO, AUTO PRESET, MANUAL
MEMORY, i.LINK, DIRECTINPUTSELECT, ATV, DTV, EPG, RADIO etc. ...
• If [INPUT MODE START] is Normal, this function cannot be set.
Set to “VARIABLE” automatically.
• When setting to “FIXED”,
The item related to the channel setting and input selection in Menu are not displayed.
ON TIMER (Watching reservation) is not active.
* These items does not exist according to the model.
3 – 13
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
13)Speaker ON/OFF selection [LOUD SPEAKER]
Option
Default
Function
Remarks
“ON” or “OFF” (loop enabled)
ON
ON
: The sound from the speakers is output.
OFF
: The sound from the speakers is not output even if the headphones are not used.
• When the VOL (+/-) key is pressed, the mute icon is displayed for 4 seconds.
• For the MUTE key and sound-related keys, caution is displayed.
• For the headphones, normal operation is possible.
14)Remote control path through [RC PATH THROUGH]
Option
Default
Function
Exception
Remarks
“OFF”, “ON: TVRCE” or “ON: TVRCD” (loop enabled)
OFF
The item decide whether the signal received by the remotecontrol’ slight-receiving section is output to the blankpin
(9pin) of RS232C.
OFF
: this function is not active.
ON: TVRCE
: this function is active, and remote control is active, too
ON: TVRCD
: this function is active, but remote control is not active
• In the case of “ON:TV RCD”, the start operation in the adjustment process mode, inspection mod are enabled
regardless of this setting.
• In the case of “ON: TV RCD”, all the keys are enabled regardless of this setting while entering the adjustment process mode, inspection mode or Public mode setting screen.
* Remote control path through does not exist according to the model.
15)232C power ON control [232C POWON]
Option
Default
Function
“ENABLE” or “DISABLE” (loop enabled)
DISABLE
The item decide whether Power ON by the 232C command is enabled/disabled in the standby state.
The same function as 232C command “RSPW”.
ENABLE
: POWR0001 is always enabled.
DISABLE
: Start-up may be impossible at POWR0001.
(If the 232C command reception module is set to OFF, the command is invalid.)
16)Public mode setting [PUBLIC MODE]
Option
Default
Function
Remarks
“OFF” or “ON” (loop enabled)
OFF
The item decide whether Public mode setting menu are enabled or disabled.
The same item as [PUBLIC MODE] in the adjustment process menu.
OFF
: Public mode is not active
ON
: Public mode is active
Each operation of the Public mode is impossible unless this item is set to ON.
11. Video signal adjustment procedure
The adjustment process mode menu is listed in Section 5.
Signal generator level adjustment check (Adjustment to the specified level)
•
•
•
Composite signal PAL/SECAM
RGB signal
15K component signal (50 Hz)
•
33K component signal (50 Hz)
•
ANALOG RGB signal
: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
: 0.7Vp-p ± 0.02Vp-p
: Y level
: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
: PB, PR level
: 0.7Vp-p ± 0.02Vp-p
: Y level
: 0.7Vp-p ± 0.02Vp-p (Pedestal to white level)
: PB, PR level
: 0.7Vp-p ± 0.02Vp-p
: RGB level
: 0.7Vp-p ± 0.02Vp-p
11.1. Entering the adjustment process mode
Enter the adjustment process mode according to Section 4.
3 – 14
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
11.2. PAL signal adjustment
1
Adjustment point
Setting
Adjustment conditions
[Signal]
PAL
Full field colour bar composite
signal
•
Adjustment procedure
Feed the PAL full field colour bar signal (75% colour saturation) to EXT1
SCART IN.
[VIDEO input signal]
[Terminal]
EXT1 SCART IN
2
*
Auto adjustment
performance
Adjustment process
[PAL ADJ]
page 4/21
100% white
Black
Bring the cursor on [PAL ADJ] and press [OK].
[PAL ADJ OK] appears when finished.
ATTENTION: Please execute [3. TUNER adjustment] afterwards if you adjust [2. PAL signal adjustment] after all adjustments are completed.
11.3. TUNER adjustment
1
Adjustment point
Setting
Adjustment conditions
[Signal]
PAL split field colour Bar
RF signal UV
[Terminal]
TUNER
Adjustment procedure
Feed the PAL Split Field colour bar signal (E-12ch) to TUNER.
Make sure the PAL colour bar pattern has the sync level of 7:3 with the
picture level.
Signal level: 55 dB µV ± 1dB (75Ω LOAD)
[E-12CH]
•
•
100% white
2
Auto adjustment
performance
Adjustment process
[TUNER ADJ]
page 3/21
Bring the cursor on [TUNER ADJ] and press [OK].
[TUNER ADJ OK] appears when finished.
11.4. SECAM adjustment
1
Adjustment point
Setting
Adjustment conditions
[Signal]
SECAM
Full field colour Bar Signal
•
Adjustment procedure
Feed the SECAM full field colour bar signal (75% colour saturation) to
EXT1 SCART IN.
[VIDEO input signal]
[Terminal]
EXT1 SCART IN
2
Auto adjustment
performance
Adjustment process
[SECAM ADJ]
page 4/21
100% white
Bring the cursor on [SECAM ADJ] and press [OK].
[SECAM ADJ OK] appears when finished.
3 – 15
Black
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
11.5. ADC adjustment (Component 15K)
1
Adjustment point
Setting
Adjustment conditions
[Signal]
COMP15K, 50Hz
100% Full field colour bar Signal
•
Adjustment procedure
Feed the COMPONENT 15K 100% full field colour bar signal (100%
colour saturation) to EXT3 COMPONENT IN.
[Terminal]
EXT3 COMPONENT IN
2
Auto adjustment
performance
Adjustment process
[COMP15k ALL ADJ]
page 6/21
100% white
Black
Bring the cursor on [COMP15k ALL ADJ] and press [OK] [COMP15k ALL
ADJ] [OK] appears when finished.
11.6. ADC adjustment (Component 33K)
1
Adjustment point
Setting
Adjustment conditions
[Signal]
COMP33K, 50Hz
100% Full field colour bar Signal
•
Adjustment procedure
Feed the COMPONENT 33K 100% full field colour bar signal (100%
colour saturation) to EXT3 COMPONENT IN.
[Terminal]
EXT3 COMPONENT IN
2
Auto adjustment
performance
Adjustment process
[HDTV ADJ]
page 7/21
100% white
Black
Bring the cursor on [HDTV ADJ] and press [OK].
[HDTV ADJ OK] appears when finished.
11.7. PC signal adjustment (ANALOG RPG)
1
Adjustment point
Setting
Adjustment conditions
•
[Signal]
XGA, 60Hz
100% Full Field Colour Bar Signal
Adjustment procedure
Feed the XGA 60Hz 100% full field colour bar signal (100% colour saturation) to EXT3 PC IN.
[Terminal]
EXT3 PC IN
2
Auto adjustment
performance
Adjustment process
[ANALOG PC ADJ] menu
page 8/21
100% white
Black
Bring the cursor on [ANALOG PC ADJ] and press [OK].
[ANALOG PC ADJ OK] appears when finished.
11.8. RGB (SCART) adjustment (RGB 15K)
1
Adjustment point
Setting
Adjustment conditions
[Signal]
RGB 15K, 50Hz
100% Full field colour bar signal
•
Adjustment procedure
Feed the RGB 15k 50Hz 100% full field colour bar signal (100% colour
saturation) to EXT1 SCART IN.
[Terminal]
EXT1 SCART RGB IN
2
Auto adjustment
performance
Adjustment process
[SCART RGB ADJ] menu
page 9/21
100% white
Bring the cursor on [SCART RGB ADJ] and press [OK].
[SCART RGB ADJ OK] appears when finished.
3 – 16
Black
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
12. White Balance Adjustment
For white balance adjustment, adjust the offset values on pages 11/21.
[Condition of the unit for inspection]
[Input signal condition]
[Adjustment reference device]
: Modulated light (+16), Colour temperature (High)
AV MODE: DYNAMIC
Active Backlight: OFF
OPC: OFF
Asing Time: Min,60 minute
: HDMI 1080i 15IRE (LO), 78IRE (HI)
: Minolta CA-210
[Adjustment procedure]
1) Display the current adjustment status at R/G/B_GAIN (HI). (Page 11/21 of process adjustment)
The signal of 78IRE is input.
2) Read the value of the luminance meter. x = 0.272, y = 0.277
3) Change R_GAIN (HI)/B_GAIN (HI) (Adjustment offset value) on page 11/21 of process adjustment so that the values of the luminance meter
approach x = 0.272 and y = 0.277.
(Basically, G is not changed. If adjustment fails with R and B, change G. When G is lowered, the weaker of R or B must be fixed.)
4) Display the adjustment status of the current R/G/B_GAIN (LO).
The signal of 15IRE is input.
Change R_GAIN (LO)/B_GAIN (LO) (adjustment offset value) on page 11/21 of process adjustment so that the values of the luminance meter
approach x = 0.272 and y = 0.277.
5) Both HI and LO are repeating the step from 1 to 4 until becoming an aim value.
[Adjustment reference standard value]
Adjustment spec ± 0.002
Inspection spec ± 0.004 (point LO)
Adjustment spec ± 0.001
Inspection spec ± 0.002 (point HI)
6) After completing adjustments, set EEP SAVE (21/21) to ON in the process menu to save the white balance adjustment value.
13. Confirmation item
1. HDMI-CEC Inspection
After repairing the CEC function, check the operation about HDMI-CEC circuit
2. CI card Inspection
After repairing the CI function, check that the DTV signal is received in the UK setting by inserting CAM
And check the KEY certification by inserting CAM which is prepare for CI+
3. LAN Inspection
After repairing the LAN function, check the communication by connecting PC and LAN terminal.
3 – 17
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
14. Initialization to factory settings
CAUTION: When the factory settings have been made, all user setting data, including the channel settings, are initialized.
(The adjustments done in the adjustment process mode are not initialized.) Keep this in mind when initializing these settings.
1
Adjustment point
Factory settings
Adjustment conditions
ends by turning off the
MAIN POWER key.
(See to below caution)
Adjustment procedure
[Factory setting with adjustment process mode]
• Enter the adjustment process mode.
• Move the cursor to [INDUSTRY INIT] on page 2/21.
• Use the R/C key to select a region from [EUROPE/RUSSIA] and press the [OK] key.
• “EXECUTING” display appears.
• After a while, “SUCCESS” display appears, the setting is completed.
When succeeding: Background colour (green)
When failing: Background colour (red)
The following items are initialized in the factory setting.
1) User settings
2) Channel data (e.g. broadcast frequencies)
3) Maker option setting
4) Password data
After adjustments, exit the adjustment process mode.
To exit the adjustment process mode, unplug the AC power cord from the outlet to forcibly turn off the power.
When the power is turned off with the remote control, unplug the AC power cord and plug it back in (wait approximately 10 seconds before plugging
in the AC power cord)
Please execute the initialized in the factory setting again when you turn on the power supply after the initialized in the factory setting is set.
15. Upgrading the software
1. Turn on the AC power.
2. Insert the upgrading USB flash memory for upgrade into the service slot.
(After a while, an external input changes into USB automatically.)
3. Use the Menu button and cursor keys ( / / / ), CH keys (
on OSD menu.
/
) of R/C or on the set to select Menu - Setup - Information - Software update
4. The message (Insert the USB memory device contains the software update file) shows up.
Push OK when if there is no problem.
5. After a while, if software update file is detected in the USB memory device, the following screen shows up.
Select OK when if there is no problem.
NOTE: If there is no software update file in the USB memory device, caution shows up.
Please insert the correct file and retry software update.
NOTE: If software update file in the USB memory device doesn't mutch this model, caution shows up.
Please insert the correct file and retry software update.
NOTE: If software update file in the USB memory device is already installed, caution shows up.
Please reconfirm the software version and reinstall (if necessary).
Menu(Setup
Software Update)
Software update file is detected
in the USB memory device
start update
current version : xxxxxx
update version : xxxxxx
YES
NO
3 – 18
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
6. The caution for update showes up.
•
The picture will temporary go dark until the software update display apeeares
•
Wait several minutes and don't unplug the AC cord
Select OK when if there is no problem.
7. Software update starts.
Please wait for a while until the bar shows 100%
NOTE: Do not take out the USB memory device during updating.
Menu(Setup
Software Update)
LExxx
Now Updating
Don't unpluged AC cord
update version xxxxxxx
xx %
8. When all the procedures are complete, the following upgrade success screen shows up.
The new software version can be confirmed on screen.
After a while, Turn off power and boot-up automatically.
NOTE: TV is restarted automatically, the AC code need not be pulled out.
Menu(Setup
Software Update)
LExxx
Software Update Complete
xxxxxxx
9. After boot-up, the following caution shows up.
Select OK when if there is no problem.
Software update is completed, please remove the USB memory device.
system software was
succesfully updated
Remove the USB memory device.
OK
NOTE: Then get the set started and call the process adjustment screen 1/21 to check the main software version.
3 – 19
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
Service
CHAPTER 4. TROUBLESHOOTING TABLE
LC-40LE812E
Manual
[1] TROUBLESHOOTING TABLE
No sound (during the reception of TV (DIGITAL) broadcasting)
Does not the sound go out though the picture has come out when DTV is received?
Is IF signal output to pins (10, 11) of TU1101?
NO
Check the tuner and its peripheral circuits.
Replace as required.
YES
Is IF signal sent to pins (14, 15) of IC1102 (Multiplexer)?
NO
Check the line between TU1101 and IC1102.
YES
Are pins (9, 10, 11) of IC1102 at H/L?
L
Is IF signal sent to pins (AA29/D__IF_P, AB29/D__IF_N) of
IC3302 (Digital AV decode & Main CPU)?
YES
Refer to “No sound output in all modes.”
H
Is IF signal sent to pins (41/INM, 42/INP) of IC1106?
NO
Check the line between IC1102 and IC1106.
YES
Is signal output to pins (17/CTS_CK_60MHz, 18/CTS_SY, 19/
CTS_VA, 21/CTS_D0) of IC1106?
NO
Check IC1106 and its peripheral circuits.
YES
Is signal sent to pins (2, 3/CS_TS_CK, 5, 6/CS_TS_SY, 10, 11/
CS_TS_VA, 14/CS_TS_D7) of IC4409 (TS SW)?
NO
Check the line between IC1106 and IC4405.
Is pins (2) of IC4409 at H?
NO
Check the line between IC4409 and 21pins of IC4405.
YES
Is signal sent to pins (11/TS_DATA1, 12/TS_DATA2, 13/
TS_DATA3, 14/TS_DATA4) of IC4405?
NO
Check the line between IC1106 and IC4405.
YES
Is signal output to pins (122/TS_VALIDO, 123/TS_CLKO, 124/
TS_DATAO, 124/TS_SYNCO) of IC4405?
NO
Check IC4405 and its peripheral circuits.
NO
Check the line between IC4405 and IC3302.
YES
YES
Is signal sent to pins (A30/TS_CPUIN_VAL, B30/
TS_CPUIN_CLK, C30/TS_CPUIN_SYNC, C29/TS_CPUIN_D0)
of IC3302 (Digital AV decode & Main CPU)?
YES
Refer to “No sound output in all modes.”
4–1
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
No sound (during the reception of TV (DIGITAL-Satellite) broadcasting)
Does not the sound go out though the picture has come out when DTV is received?
Is signal input to TU1301?
NO
Check the setting of an external input device that connects with
TU1301.
YES
Is signal sent to pins (2, 3/CS_TS_CK, 5, 6/CS_TS_SY, 10, 11/
CS_TS_VA, 14/CS_TS_D7) of IC4409 (TS SW)?
NO
Check the line between TU1301 and IC4409.
Check TU1301 and its peripheral circuits (IC1301 etc. ⋅⋅⋅).
Replace as required.
Is pins (2) of IC4409 at L?
NO
Check the line between IC4409 and 21pins of IC4405.
YES
Is signal sent to pins (4/CS_TS_SCK, 7/CS_TS_SSY, 9/
CS_TS_SVA, 12/CS_TS_SDATA) of IC4409?
NO
Check IC4409 and its peripheral circuits.
YES
Is signal sent to pins (11/T0_DATA1, 12/T0_DATA2, 13/
T0_DATA3, 14/T0_DATA4) of IC4405?
NO
Check the line between IC4409 and IC4405.
YES
Is signal output to pins (122/TS_VALIDO, 123/TS_CLKO, 124/
TS_DATAO, 124/TS_SYNCO) of IC4405?
NO
Check IC4405 and its peripheral circuits.
NO
Check the line between IC4405 and IC3302.
YES
YES
Is signal sent to pins (A30/TS_CPUIN_VAL, B30/
TS_CPUIN_CLK, C30/TS_CPUIN_SYNC, C29/TS_CPUIN_D0)
of IC3302 (Digital AV decode & Main CPU)?
YES
Refer to “No sound output in all modes”.
No picture on the display (4)
Does not the picture come out when DTV (Satellite) is received?
Refer to “No sound (during the reception of TV(DIGITAL-Satellite) broadcasting)”.
4–2
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
CHAPTER 5. MAJOR IC INFORMATIONS Service
LC-40LE812E
Manual
[1] MAJOR IC INFORMATIONS
REF NO
[MAIN UNIT]
IC8401
RH-iXC147WJQZQ
Flash
IC3302
RH-iXC951WJN1Q
Main CPU
IC2002
RH-iXC786WJQZQ
for service
(RH-iXC786WJNJQ)
RH-iXC754WJQZQ
UCOM
IC3501/3502
Name
Part Code
Description
DDR
1K bit E2PROM
IC8455
VHi24LC21AT-1Y
for service
(RH-iXD108WJQZS)
VHiR24064AS-1Y
IC506
VHiM3221EIP-1Y
RS232C-DRIVER
IC4405
VHiMT8295AE-1Q
CI controler
IC2004
VHiR24002AS-1Y
2K bit E2PROM
IC1504
VHiSii9287+-1Q
HDMI_Port _Processor
IC1106
VHiSTV0297E-1Q
COFDM
IC9501
(LC-40/46/52LE822E,
LC-40/46LU822E)
IC2701
VHiKSZ8041T-1Y
Ethernet Bus Interface
VHiYSS951VZ-1Y
Sound processor
IC2702/2703
VHiYDA164QZ-1Y
Audio-AMP
IC1301
RH-iXC563WJQZ
LNB supply and control
IC501
64K bit E2PROM
This IC is 512MB NAND flash memory.
This IC stores the software data that processes the system of TV such
as the graphic processing, the LCD controls, and backlights etc.
This IC is Video Processor & MAIN CPU.
In this IC, the decode processing and the video signal processing are
done. Moreover, OSD is generated here and added to a picture signal.
The monitor microprocessor is intended to communicate with the main
CPU and to operate the system.
It also controls power of the entire system.
This IC is 1GB DDR2 SDRAM.
This IC operates as a memory of IC3302 (Video Processor). ***
This IC is a 1Kbit-2-wire (I2C bus type) serial EEPROM that can be
programmed electrically. The EEPROM chip stores the EDID data of
PC input. This data is controlled through I2C signals.
The BR24S64W is a 64Kbit-2-wire (I2C bus type) serial EEPROM that
can be programmed electrically. This IC stores the menu data and the
adjustment value data of adjustment process mode etc. The data is
given out by commands from the main microprocessor.
The MAX3221E is a single driver, single receiver RS-232 solution
operating from a single Vcc supply. The RS-232 pins provide IEC
G1000-4-2 ESD Protection. The device meets the requirements of
TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controler and the serial-port connector. The
charge pump and four small external capacitors allow operation from a
single 3V to 5.5V supply.
This is a control IC for PCMCIA cards. This controls information on IC
cards inserted into the PCMCIA card slot (SC4401) or information on
software version upgrade cards saved on flash memories to transfer
the data to CPUs and memories.
This is a 2Kbit-2-wire (I2C bus type) serial EEPROM that can be programmed electrically. This IC stores the menu data and the adjustment value data of adjustment process mode etc. The data is given
out by commands from the main microprocessor.
The SiI9287 HDMI port processor is the second generation of HDMI
devices that support revision 1.3 of the HDMI specification. The main
feature is as follows.
1) 4-input, 1-output HDMI port processor.
2) Integrated TMDS receiver and transmitter cores capable of receiving and transmitting at 2.25Gbps.
3) Supports video resolutions up to 1080p, 60Hz, 12bit or 720p/1080i,
120Hz,12bit.
4) Receiver fully comply with DVI1.0, HDCP1.1 and HDMI1.3 specifications.
The STV0297E’s demodulator is a complete QAM (quadrature amplitude modulation) demodulation and FEC (forward error correction)
solution that performs IF to transport stream block processing of QAM
signals. It is intended for the digital transmission of compressed television, sound, and data services over cable.
This IC is a single supply 10Base-T/100Base-TX Physical Layer
Transceiver, which provides MII/RMII/SMII interfaces to transmit and
receive data.
This IC is the Sound processing LSI with built-in two DSP (MDSP/
SDSP) and FM (frequency modulation) oscillators. This IC process
sound signal and sent it to AMP for Speaker and Woofer
This IC is digital audio power amplifier with digital audio interface.
The power-supply voltage is corresponded to A.8V~18V and the maximum output is 20Wx2ch.
It is IC for amplifying the feeble electric wave sent from satellite broadcasting on the level which can treat a decoder, and changing and processing signal.
5–1
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
CHAPTER 6. OVERALL WIRING/BLOCK DIAGRAM
LC-40LE812E
Service Manual
[1] OVERALL WIRING DIAGRAM (LC-40LE812E/LX812E)
OVERALL WIRING DIAGRAM (LC-40LE812E/LX812E)
J
Module Unit
[L1]
Woofer
[L2]
[LB]
21
P9602 1
9
QCNW-K978WJQZ
1
[PD]
P9601
1
QCNW-K976WJQZ 12
[PD]
G
1
8
[AS]
[SP]
P2701
QCNW-K556WJQZ
QCNW-K554WJQZ
F
[SB]
P2702
QCNW-K553WJQZ
[LB]
9
1
1
9
1
6
USB
J3301
H/P
Audio out
J504
MAIN Unit
15
AV-IN
J505
1
5
20 19
2 1
PC/COMP
D-SUB
SC501
[AC]
HDMI/PC/COM
P
Audio
J501
[PL]
HDMI1
SC1503
[LW]
P2601
LCD-Controler
1
HDMI1
SC1502
1
41
1
[LW]
QCNW-K576WJQZ
[RA]
P2005
41
D
14
HDMI1
SC1501
HDMI
QCNW-K977WJQZ
HDMI1
SC1505
HDMI
POWER
SW
E
USB
POWER Unit
H
HDMI
I
1
1
10
14
QCNW-K551WJQZ 15
QACCKA052WJPZ
1
3
4
[PL] 1
TUNER
CI card slot
SC4401
DVB-S
TUNER
C
SCART
SC505
1
80
1
RS232C
D-SUB 9pin
SC504
OpticalOut
D520
80
B
Touch Key Unit
R/C Unit
A
1
2
3
[KM]
Icon Unit
[RA]
4
5
6
7
8
9
10
[RI]
11
6–1
12
13
14
15
16
17
18
19
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[2] OVERALL WIRING DIAGRAM (LC-46LE812E/LX812E)
OVERALL WIRING DIAGRAM (LC-46LE812E/LX812E)
J
Module Unit
QCNW-K570WJQZ
I
Woofer
[L1]
[L2]
H
POWER Unit
[SB]
P2702
[LB]
21
P9602 1
9
QCNW-K978WJQZ
1
[PD]
P9601
1
QCNW-K976WJQZ 12
G
[PD]
1
8
[SP]
P2701
F
QCNW-K559WJQZ
1
1
9
1
6
USB
J3301
H/P
Audio out
J504
MAIN Unit
15
AV-IN
J505
1
5
20 19
2 1
PC/COMP
D-SUB
SC501
[AC]
HDMI/PC/COM
P
Audio
J501
[PL]
HDMI1
SC1503
QCNW-K556WJQZ
[LW]
P2601
LCD-Controler
QCNW-K577WJQZ
1
1
41
HDMI1
SC1501
HDMI1
SC1505
1
41
[RA]
P2005
QCNW-K572WJQZ
QACCKA052WJPZ
(For UK : QACCBA099WJPZ)
HDMI1
SC1502
1
[LW]
D
14
HDMI
POWER
SW
HDMI
E
HDMI
[AS]
9
USB
[LB]
1
14
15
1
3
4
[PL] 1
10
TUNER
CI card slot
SC4401
DVB-S
TUNER
QCNW-K977WJQZ
C
SCART
SC505
1
80
1
80
RS232C
D-SUB 9pin
SC504
OpticalOut
t
D520
B
Touch Key Unit
A
R/C Unit
1
2
[KM]
Icon Unit
[RA]
3
4
5
6
7
8
9
[RI]
10
11
6–2
12
13
14
15
16
17
18
19
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[3] OVERALL WIRING DIAGRAM (LC-40LE822E/LU822E)
OVERALL WIRING DIAGRAM (LC-40LE822E/LU822E)
J
Module Unit
[L1]
Woofer
[L2]
[SB]
P2702
QCNW-K553WJQZ
[LB]
[LB]
21
P9602 1
9
QCNW-K978WJQZ
1
[PD]
P9601
1
QCNW-K976WJQZ 12
[PD]
G
1
8
[AS]
[SP]
P2701
QCNW-K554WJQZ
QCNW-K556WJQZ
1
1
9
1
6
USB
J3301
LAN
J9501
H/P
Audio out
J504
MAIN Unit
15
AV-IN
J505
1
5
[AC]
F
9
20 19
2 1
PC/COMP
D-SUB
SC501
SC CARD
Connector
SC8454
HDMI/PC/COM
P
Audio
J501
[PL]
HDMI1
SC1503
[LW]
P2601
LCD-Controler
1
HDMI1
SC1502
1
41
1
[LW]
QCNW-K576WJQZ
[RA]
P2005
41
D
14
4
[PL] 1
HDMI1
SC1505
1
1
QCNW-K551WJQZ 15
[RL]
P2006 1
QACCKA052WJPZ
HDMI1
SC1501
HDMI
QCNW-K977WJQZ
HDMI
POWER
SW
E
USB
POWER Unit
H
HDMI
I
3
10
14
TUNER
CI card slot
SC4401
DVB-S
TUNER
C
SCART
SC505
1
80
1
RS232C
D-SUB 9pin
SC504
80
OpticalOut
D520
B
Touch Key Unit
R/C Unit
A
1
2
[KM]
QCNW-K580WJQZ
Icon Unit
[RA]
3
4
5
6
7
8
9
10
11
6–3
LOGO
[RI]
12
13
14
15
16
17
[RL]
18
19
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[4] OVERALL WIRING DIAGRAM (LC-46LE822E/LU822E)
OVERALL WIRING DIAGRAM (LC-46LE822E/LU822E)
J
Module Unit
QCNW-K570WJQZ
I
Woofer
[L1]
[L2]
H
POWER Unit
[SB]
P2702
G
[AS]
[PD]
1
8
[SP]
P2701
F
QCNW-K559WJQZ
9
1
1
9
1
6
USB
J3301
LAN
J9501
H/P
Audio out
J504
MAIN Unit
15
AV-IN
J505
1
5
20 19
2 1
PC/COMP
D-SUB
SC501
SC CARD
Connector
SC8454
[AC]
HDMI/PC/COM
P
Audio
J501
[PL]
HDMI1
SC1503
QCNW-K556WJQZ
[LW]
P2601
LCD-Controler
QCNW-K577WJQZ
1
1
41
HDMI1
SC1501
HDMI1
SC1505
1
41
[RA]
P2005
QCNW-K572WJQZ
[RL]
P2006
QACCKA052WJPZ
4
[PL] 1
HDMI1
SC1502
1
[LW]
D
14
HDMI
POWER
SW
HDMI
E
USB
[LB]
21
P9602 1
9
QCNW-K978WJQZ
1
[PD]
P9601
1
QCNW-K976WJQZ 12
HDMI
[LB]
1
10
14
15
1
3
TUNER
CI card slot
SC4401
DVB-S
TUNER
QCNW-K977WJQZ
C
SCART
SC505
1
80
1
80
RS232C
D-SUB 9pin
SC504
OpticalOut
D520
B
Touch Key Unit
A
R/C Unit
1
2
QCNW-K580WJQZ
[KM]
LOGO
Icon Unit
[RA]
3
4
5
6
7
8
9
[RL]
[RI]
10
11
6–4
12
13
14
15
16
17
18
19
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[5] OVERALL WIRING DIAGRAM (LC-52LE822E)
OVERALL WIRING DIAGRAM (LC-52LE822E)
Module Unit
J
Woofer
I
QCNW-K574WJQZ
[L1]
H
[L2]
POWER Unit
[SB]
P2702
[AS]
[PD]
1
8
F
[SP]
P2701
QCNW-K579WJQZ
9
1
1
9
1
6
USB
J3301
LAN
J9501
H/P
Audio out
J504
MAIN Unit
15
AV-IN
J505
1
5
20 19
2 1
PC/COMP
D-SUB
SC501
SC CARD
Connector
SC8454
[AC]
E
USB
[LB]
21
P9602 1
9
QCNW-K978WJQZ
1
[PD]
P9601
1
QCNW-K976WJQZ 12
G
HDMI/PC/COM
P
Audio
J501
[PL]
HDMI
[LB]
HDMI1
SC1503
[LW]
P2601
LCD-Controler
QCNW-K577WJQZ
1
D
1
41
[RA]
P2005
1
QCNW-K562WJQZ 15
[RL]
P2006 1
QACCKA052WJPZ
4
3
10
14
TUNER
80
1
HDMI1
SC1505
CI card slot
SC4401
DVB-S
TUNER
QCNW-K977WJQZ
SCART
SC505
1
HDMI1
SC1501
1
41
C
HDMI1
SC1502
1
[LW]
[PL] 1
14
HDMI
QCNW-K556WJQZ
HDMI
POWER
SW
RS232C
D-SUB 9pin
SC504
80
OpticalOut
D520
B
Touch Key Unit
A
R/C Unit
1
2
3
QCNW-K565WJQZ
[KM]
LOGO [RL]
Icon Unit
[RA]
4
5
6
7
8
9
[RI]
10
11
6–5
12
13
14
15
16
17
18
19
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[6] SYSTEM BLOCK DIAGRAM (LC-40/46LE812E, LC-40/46LX812E)
SYSTEM BLOCK DIAGRAM (LC-40/46LE812E, LC-40/46LX812E)
CVBS
CVBS_L/R
CVBS/LR
EXT2
J
CVBS/LR
RGB
EXT1
(SCART1)
MAIN
CVBS
L/R
S-Video
RGB
[LW]
P2601
(41p )
TUNER CVBS OUT
TUNER_OUT
LR_OUT
TUNER OUT L/R
FS/FB
Mute
From CPU or UCON
FAST_SW
IC504
TUNER OUT
MM1506XN
SLOW SW
I
TU_CVBS_OUT_MUTE
From CPU or UCON
+13V
IC2703
SP AMP(2CH)
VHIYDA164QZ
IC2702
Woofer AMP
(0.1CH)
VHIYDA164QZ
AMP_DATA_
SW
+1.8V
IC2701
DSP
YSS951VZ
UCOM_RST
(400KHz 3.3V)
CI-CPU_IN
I2C_0 (400KHz)
DDC_I2C_1
HDMI_1
From CPU or UCON
E
Mute
+1.25V
+1.05V
N_SRESET
CEC_0
MT5391W(FHD)
H.264 / CI+
PWM_0
PWM_1
SPDIF
EXT3
Comp/RGB
N_CPU_RST
D-SUB
RGB
/Component
D
DTV/SPDIF
RESET
C
HDMI 4
HDMI 3
HDMI 2
DDC_3
IC1504
HDMI_3
HDMI-SW
SII9287B
DDC_2
HDMI_2
HDMI 1
DDC_1
HDMI_
CEC_0
J3301
USB
Mute
IC8401 +3.3V
NAND FLASH
512Gbit
IXC147WJQZQ
4
S13V
BU+3.3V
From CPU or UCON
[RL] P2006 (3p)
D+5V
[KM] J1 (8p)
[RA] P102 (5p)
R/C
MENU/POWER
INPUT/CHANNEL
VOLUME
3
UR13V
I2C_0_400KHz
A
2
AC_DET
PS_ON
PNL_POW
BU5V
[RA] P2005 (15p)
IC3301
LINE Reg.
[PD]
P9601
(12PIN)
POWER CIRCUIT
KEY
1
1) BU3.3V
2) D3.3V
3) D5.6V
4) D5V
5) D+1.8V
6) D+1.05V
7) STB+3.3V
8) S+8V
9) CPU+1.2V
+3.3V
DDC_4
HDMI_4
B
IC3501
DDR2(1066M)
IC3502
1Gbit
DDR2(1066M)
1Gbit
TxD/RxD
RS232C TxRx
M3221EIP
No.9 pin RC Passthrough
IC1505
OPT OUT
AHC1G08
DET_PNL12V
IC2004
EEPROM
2kbit
IC8452
SW
LCX157FT
IC501
EEPROM
+3.3V IC506
RS-232C
FRAME
BU+3.3V
KEY_POW,KEY_SCL,KEY_SDA
Audio in
RGB_L/R
OFL
DMMER
EEPROM_SCL/SDA
CVBS_L/R
From CPU or UCON
IC9601
Spliter
HC2G66DP
USB_0
Mute
RGB_LR_IN
ERROR
OFL2
27.000MHz
X3302
X'tal
CPU_UARXD0_RS
CPU_UATXD0_RS
RGB/HDMI
Audio
(Mini Plug)
I2C
VON
Audio out
SPI_FLASH
EXT3/HDMI2
[LB]
P9602
(9pin)
OFL1
Digital AV decode & Main CPU
SCART_L/R
PS_ON
PNL_POW
STB_CPU
HP/MONI_L/R
OPT_OUT
DET_SYNC
STB
AC_DET
PM_REQ, CBOOTS
IC3302
CPU_UARXD2_UCOM
CPU_UATXD2_UCOM
IC503
OPT OUT
T7SET08
ERR_PNL
PM_REQ,
SIF
OPTICAL
OUT
SUB MCU
A/D
20MHz
+1.8V
RGB HV
RGB/Component in
Headphone/
Audio
Out
THERMO
X2002
Xtal
+3.3V
I2C_0
I2C_1
I2C_2
I2S(DATA/LRCK/BCLK)
TUNER OUT_L/R
Thermister
+8.0V
CI-CPU_OUT
IF_AGC
D_IF_IN-/+
TUNER_I2C
DVB_TC_IFSW
From CI
TUNER_RESET From CPU
LVDS OUT
X1101
Xtal
FE_RST
CVBS
27.000MHz
BU+3.3V
IC2002
M16C/64A
IXC786WJ
DET_13V,DET_3.3V
TUNER_I2C
IC1102
IF_DEMUX
LV4053FT
IC1106
Demodulator
DVB-C
STV0297E
X2001
Xtal
PNL_I2C_EN
From CPU
ILL_CTRL1
TU1301
Satellite
Tuner
AGC
CNVss
PNL_WP
WP
F
+3.3V
CVBS
IF_AGC
D_IF IN-/+
I2C
SIF
TU1101
Analog/
Digital
Tuner
+1.2V
S-Video
RF IN
+3.3V
UART
UART
32.768kHz
LCX157
LCX244FT
RGB
+5V
CI_CNT_RESET
FBIN
TS_CIIN
IC4405
CI Controller
MT8295
CNVss
RxD,TxD
IC2008
Gate
7WH126FU
RxD,TxD_CPU
RC,OPC
IC4401
IC4402
IC4403
CI_CEB, CI_RB
+1.8V
ADIN5
ADIN0
CARD
INTERFACE
+3.3V
ROM_WP
IC2601
Spliter
HC2G66DP
27.000MHz
X4401
Xtal
TUNER CVBS OUT
P_TS_SW
DET_POW
PE PE
PNL_ROM_EN
(400KHz)
+3.3V
IC8455
EEPROM
64kbit
CI_D[7:0] /CI_A[14:0]
TS_CIOUT
TS_CIIN
DVB_CS_SW
IC4409
From CPU
B_STATUS
PNL_EN
RS_BUF_CNT
I2C_0
G
VCOM_WP
TCON_I2C
B_STATU
From CPU
DAC OUT1
DAC OUT2
[SB]
P2702
EXT-SP
Woofer
H
O_S_SET
FRAME
DET_SYNC
IC2001
Reset
+3.3V
LRCK/BCLK/MCLK
+13V
(400KHz)
BU+3.3V
AMP_DATA_LR
PDD[7:1]
[SP]
P2701
EXT-SP
SPEAKER
I2C_0
O_S_SET
Mute
From CPU
I2C_0 (400KHz)
5
6
7
8
9
10
11
6–6
12
13
OPC sensor
R/C receiver
14
15
[RI] P202 (2p)
[RL] P201 (3p)
ICON
LOGO
LED
x3
LED
x3
16
17
18
19
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[7] SYSTEM BLOCK DIAGRAM (LC-40/46/52LE822E, LC-40/46LU822E)
SYSTEM BLOCK DIAGRAM (LC-40/46/52LE822E, LC-40/46LU822E)
CVBS
CVBS_L/R
CVBS/LR
EXT2
MAIN
J
CVBS
CVBS/LR
RGB
EXT1
(SCART1)
[LW]
P2601
(41p)
L/R
S-Video
RGB
TUNER CVBS OUT
TUNER_OUT
LR_OUT
IC504
TUNER OUT
MM1506XN
TUNER OUT L/R
Mute
FS/FB
FAST_SW
From CPU or
UCON
SLOW SW
I
TU_CVBS_OUT_MUTE
From CPU or UCON
IC2703
SP AMP(2CH)
VHIYDA164QZ
LRCK/BCLK/MCLK
+13V
AMP_DATA_
SW
IC2701
DSP
YSS951VZ
(400KHz 3.3V)
CI-CPU_IN
Headphone/
Audio
Out
E
+1.05V
N_SRESET
CEC_0
MT5391W(FHD)
H.264 / CI+
PWM_0
PWM_1
EEPROM_SCL/SDA
BU+3.3V
D
DTV/SPDIF
RESET
IC8452
SW
LCX157FT
IC501
EEPROM
+3.3V IC506
RS-232C
C
TxD/RxD
RS232C TxRx
M3221EIP
No.9 pin RC Passthrough
HDMI 4
DDC_4
HDMI_4
HDMI 3
DDC_3
HDMI_3
HDMI 2
DDC_2
HDMI_2
HDMI 1
DDC_1
HDMI_1
B
IC1505
OPT OUT
AHC1G08
Mute
CEC_0
J3301
USB
4
S13V
DET_PNL12V
FRAME
BU5V
IC9501 +3.3V
Ethernet Bus
Interface
KSZ8041T
From CPU or
UCON
BU+3.3V
[RL] P2006 (3p)
D+5V
[KM] J1 (8p)
SC8454
SD Connector
for Time Shift
3
UR13V
POWER CIRCUIT
[RA] P2005 (15p)
IC3301
LINE Reg.
BD6538G
AC_DET
PS_ON
PNL_POW
I2C_0_400KHz
A
2
DET_SYNC
IC8401 +3.3V
NAND FLASH
512Gbit
IXC147WJQZQ
IC1504
HDMI-SW
SII9287B
OFL
DMMER
[PD]
P9601
(12PIN)
1) BU3.3V
2) D3.3V
3) D5.6V
4) D5V
5) D+1.8V
6) D+1.05V
7) STB+3.3V
8) S+8V
9) CPU+1.2V
+3.3V
[RA] P102(5p)
R/C
KEY
1
IC2004
EEPROM
2kbit
KEY_POW,KEY_SCL,KEY_SDA
SPDIF
N_CPU_RST
D-SUB
RGB
/Component
IC9601
Spliter
HC2G66DP
IC3501
DDR2(1066M)
IC3502
1Gbit
DDR2(1066M)
1Gbit
SDIOCMD/SDIOCLK
SDI0㨪3
ONDD8㨪
15
ONDA6㨪
Audio in
RGB_L/R
USB_0
CVBS_L/R
From CPU or UCON
ERROR
OFL2
27.000MHz
X3302
X'tal
CPU_UARXD0_RS
CPU_UATXD0_RS
Mute
RGB_LR_IN
I2C
VON
Audio out
SPI_FLASH
EXT3
Comp/RGB
RGB/HDMI
Audio
(Mini Plug)
[LB]
P9602
(9pin)
PNL_POW
OFL1
Digital AV decode & Main CPU
SCART_L/R
EXT3/HDMI2
PS_ON
STB_CPU
HP/MONI_L/R
OPT_OUT
O_S_SET
STB
AC_DET
PM_REQ,
PM_REQ, CBOOTS
CPU_UARXD2_UCOM
CPU_UATXD2_UCOM
IC503
OPT OUT
T7SET08
ERR_PNL
+1.25V
SIF
OPTICAL
OUT
SUB MCU
A/D
20MHz
IC3302
DDC_I2C_1
HDMI_1
I2S(DATA/LRCK/BCLK)
TUNER OUT_L/R
IC2002
M16C/64A
IXC786WJ
+1.8V
RGB HV
RGB/Component in
From CPU or
UCON
Mute
X2002
Xtal
BU+3.3V
UART
32.768kHz
THERMO
Thermister
+3.3V
I2C_0
I2C_1
I2C_2
DVB_TC_IFSW
From CI
TUNER_RESET From CPU
X2001
Xtal
+8.0V
CI-CPU_OUT
IF_AGC
D_IF_IN-/+
TUNER_I2C
I2C_0 (400KHz)
CNVss
PNL_WP
PNL_I2C_EN From CPU
DET_13V,DET_3.3V
FE_RST
LVDS OUT
X1101
Xtal
CVBS
IC1106
Demodulator
DVB-C
STV0297E
27.000MHz
UART
ILL_CTRL1
IC1102
IF_DEMUX
LV4053FT
+1.2V
S-Video
AGC
TUNER_I2C
CI_CNT_RESET
IC2008
Gate
7WH126FU
RxD,TxD_CPU
RC,OPC
TU1301
Satellite
Tuner
F
+3.3V
+3.3V
D_IF IN-/+
I2C
SIF
TU1101
Analog/
Digital
Tuner
IC4405
CI Controller
MT8295
CNVss
RxD,TxD
LCX157
LCX244FT
CVBS
IF_AGC
+3.3V
CI_CEB, CI_RB
+1.8V
FBIN
+5V
CI_D[7:0] /CI_A[14:0]
TS_CIOUT
TS_CIIN
DVB_CS_SW
IC4409
IC4401
IC4402
IC4403
TS_CIIN
+3.3V
IC8455
EEPROM
64kbit
ROM_WP
IC2601
Spliter
HC2G66DP
27.000MHz
X4401
Xtal
RGB
CARD
INTERFACE
PNL_ROM_EN
(400KHz)
P_TS_SW
DET_POW
PE PE
PNL_EN
RS_BUF_CNT
From CPU
RF IN
B_STATUS
UCOM_RST
From CPU
I2C_0
G
VCOM_WP
TCON_I2C
B_STATUS
ADIN5
ADIN0
H
IC2702
Woofer AMP
(0.1CH)
VHIYDA164QZ
[SB]
P2702
EXT-SP
O_S_SET
FRAME
DET_SYNC
IC2001
Reset
+3.3V
+1.8V
TUNER CVBS OUT
Woofer
(400KHz)
BU+3.3V
AMP_DATA_LR
DAC OUT1
DAC OUT2
[SP]
P2701
EXT-SP
PDD[7:1]
SPEAKER
I2C_0
+13V
WP
Mute
From CPU
I2C_0 (400KHz)
5
6
7
8
9
10
11
6–7
J9501
Ethernet for LAN
12
MENU/POWER
INPUT/CHANNEL
VOLUME
13
OPC sensor
R/C receiver
14
15
[RI] P202 (2p)
(2PIN)
[RL] P201 (3p)
ICON
LOGO
LED
x3
LED
x3
16
17
18
19
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
—MEMO—
6–8
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
PartsGuide
PARTS GUIDE
No. S60G440LE812E
LCD COLOUR TELEVISION
LC-40LE812E
LC-46LE812E
LC-40LX812E
LC-46LX812E
MODELS
LC-40LE822E
LC-46LE822E
LC-52LE822E
LC-40LU822E
LC-46LU822E
CONTENTS
[1]
PRINTED WIRING BOARD
ASSEMBLIES
[2]
LCD PANEL MODULE
[3]
CABINET PARTS
(LC-40LE812E/LX812E)
[4]
CABINET PARTS
(LC-46LE812E/LX812E)
[5]
CABINET PARTS
(LC-40LE822E/LU822E)
[6]
CABINET PARTS
(LC-46LE822E/LU822E)
[7]
CABINET PARTS (LC-52LE822E)
[8]
SUPPLIED ACCESSORIES
[9]
PACKING PARTS
(NOT REPLACEMENT ITEM)
(LC-40LE812E/LX812E/LE822E/
LU822E)
[10] PACKING PARTS
(NOT REPLACEMENT ITEM)
(LC-46LE812E/LX812E/LE822E/
LU822E)
[11] PACKING PARTS
(NOT REPLACEMENT ITEM)
(LC-52LE822E)
[12] SERVICE JIGS
(USE FOR SERVICING)
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[1] PRINTED WIRING BOARD ASSEMBLIES
!
!
!
N
N
N
N
N
N
N
N
N
N
N
N
DKEYDF455FM06
DKEYDF455FM07
DUNTKF494FM02
DUNTKF493FM03
DUNTKF493FM04
RUNTKA690WJQZ
RUNTKA692WJQZ
RUNTKA685WJQZ
RUNTKA686WJQZ
RUNTKA694WJQZ
RUNTK4512TPZC
RUNTK4437TPZE
CA
CM
N
N
N
N
N
N
N
N
N
N
N
N
P
P
P
P
P
P
P
P
P
P
P
P
MAIN Unit (LC-40/46LE812E, LC-40/46LX812E)
MAIN Unit (LC-40/46/52LE822E, LC-40/46LU822E)
R/C, LED Unit
ICON Unit
LOGO Unit (LC-40/46/52LE822E, LC-40/46LU822E)
TOUCH SENSOR Unit (LC-40/46/52LE822E, LC-40/46LU82
TOUCH SENSOR Unit (LC-40/46LE812E, LC-40/46LX812E)
POWER/LED CONTROL Unit (LC-40/46/52LE822E, LC-40/46LU822E)
POWER/LED CONTROL Unit (LC-40/46LE812E, LC-40/46LX812E)
POWER/LED CONTROL Unit (LC-52LE822E)
LCD CONTROL Unit (LC-40LE812E/LX812E/LE822E/LU822E, LC-52LE822E)
LCD CONTROL Unit (LC-46LE812E/LX812E/LE822E/LU822E)
N
N
N
N
N
P
P
P
P
P
40" LCD Panel Module Unit (LC-40LE822E/LU822E)
40" LCD Panel Module Unit (LC-40LE812E/LX812E)
46" LCD Panel Module Unit (LC-46LE822E/LU822E)
46" LCD Panel Module Unit (LC-46LE812E/LX812E)
52" LCD Panel Module Unit (LC-52LE822E)
[2] LCD PANEL MODULE
N
N
N
N
N
R1LK400D3LWF0Y
R1LK400D3LWF2Y
R1LK460D3LWA0Y
R1LK460D3LWA2Y
R1LK520D3LWA0Y
2
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[3] CABINET PARTS (LC-40LE812E/LX812E)
a
39
J
1
33
L
39
L
q
ICON
Unit
f
g
d
TOUCH
b R/C, SENSOR
LED Unit Unit
26
44
m
44
55
n
8
18
F
K
56
p
p
53
13
44
H
51
14
17
11
g
44
14
16
E
44
h
51
12
a
7
h
30
b
K
10
40
G
32
2-2
k
46
40" LCD
Panel Module Unit
2-1
2
47
2-3
19
5
B
44
38
C
X3
16
4
C
38
2-4
2-9
46
2-6
X1
X2
A
2-10
X3
A
48
2-7
9
2-7
44
3
46
15
2-5
44
16
16
q
44
52
23
E
d
20
22
45
n
36
44
21
17
25
j
50
28
F
G
44
44
44
45
16
k
37
17
B
44
POWER
j
Unit
31
m
44
44
f
27
29
44
MAIN
Unit
6
44
52
17
35
21
44
X3
X1
41
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[3] CABINET PARTS (LC-40LE812E/LX812E)
!
!
1
1
2
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-9
2-10
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
25
26
27
28
29
30
31
32
33
35
36
37
38
39
40
41
44
45
46
47
48
50
51
52
53
55
56
57
58
59
60
CCABAC527WJ11
CCABAC527WJ13
CCABBB698WJ14
Not available
Not available
Not available
Not available
Not available
Not available
Not available
Not available
Not available
GCOVAD696WJ1A
GCOVAD699WJ1A
GCOVAD710WJSA
GCOVAD711WJSA
GCOVAD709WJ1A
LANGKC719WJM1
LANGKC743WJFW
LANGKC744WJFW
LANGKC745WJFW
LANGKC746WJFW
LANGKC775WJM1
LHLDKA011WJKZ
LHLDWA143WJKZ
LHLDWA294WJUZ
LHLDZA587WJKZ
LX-BZA170WJF9
LX-BZA364WJF7
NSFTZA362WJFW
PCLiCA004WJKZ
PMLT-A636WJZZ
PZETKA548WJKZ
PZETKA556WJKZ
QACCKA052WJPZ
QCNW-K976WJQZ
QCNW-K977WJQZ
QCNW-K551WJQZ
QCNW-K978WJQZ
QCNW-K553WJQZ
QCNW-K554WJQZ
QCNW-K556WJQZ
QCNW-K576WJQZ
QEARZ0057CEFW
QEARZA186WJZZ
RSP-ZA474WJZZ
RSP-ZA476WJZZ
TLABNC117WJZZ
XBPS730P06WS0
XBPS730P10WS0
XBPS830P06WS0
XBPS830P14WS0
XEBS840P10000
PSPAZC492WJKZ
PSPAGA889WJKZ
PSPAGA891WJKZ
PZETKA563WJKZ
PCUSGA142WJKZ
PSPAZC494WJKZ
TLABZC453WJZZ
PMLT-A637WJQZ
RCORFA023WJZZ
TLABZC596WJZZ
-
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
AD
AC
AC
AC
AC
AB
N
AC
AG
AE
AF
N
N
N
N
N
N
N
N
N
N
N
N
AB
N
N
N
N
AA
AA
AA
N
AF
N
AE
AD
N
N
N
N
N
AK
N
P
P
P
P
P
P
P
P
P
P
P
P
P
P
J
J
J
J
J
J
P
J
P
P
P
P
J
J
P
J
P
P
P
P
J
P
P
P
P
J
J
J
P
J
P
J
J
P
P
P
P
P
J
P
Front Cabinet Ass'y (LC-40LE812E)
Front Cabinet Ass'y (LC-40LX812E)
Rear Cabinet Ass'y
Rear Cabinet
Terminal Label (Side)
Terminal Label (Bottom)
Himeron
Spacer
Insulation Sheet
Himeron, x4
Himeron
Himeron
Stand Cover
AC Cord Cover
Terminal Angle (Side)
Terminal Angle (Bottom)
ECO Switch Cover
Stand Angle
LCD Angle (Bottom-L)
LCD Angle (Bottom-R)
LCD Angle (Top-L)
LCD Angle (Top-R)
VESA Angle, x2
AC Cord Band
Wire Holder, x5
Wire Holder, x4
Spacer, x5
Screw (for VESA/Rear Cabinet Ass'y), x4
Screw (for Woofer), x4
Shaft (for PWB/Angle), x4
Nylon Rivet, x2
Gasket
Insulation Sheet (Power)
Insulation Sheet (ECO)
AC Cord
Connecting Cord (PD)
Connecting Cord (PL)
Connecting Cord (RA)
Connecting Cord (LB)
Connecting Cord (SB)
Connecting Cord (SP)
Connecting Cord (AS)
Connecting Cord (LW)
Earth Spring
Conductive Tape, x2
Speaker (L/R), x2
Speaker (Woofer)
Model Label
Screw (for PWB/Angle/LCD/Cabinet), x39
Screw (for Panel Angle), x3
Screw (for Rear Cabinet Ass'y), x13
Screw (for Rear Cabinet Ass'y)
Screw (for Speaker), x4
Spacer, x2
Spacer, x2
Spacer, x2
Insulation Sheet (AC)
Rubber Bush, x2
Cooling Sheet
Panel Label
Gasket
Core
Label (LC-40LX812E)
4
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[4] CABINET PARTS (LC-46LE812E/LX812E)
a
41
J
1
35
L
41
L
d
ICON
Unit
p
TOUCH
SENSOR
b R/C,
Unit
LED Unit
f
g
28
8
j
46
POWER
Unit
46
20
k
F
K
m
58
m
31
29
j
33
46
57
13
H
19
11
g
47
55 15
19
B
14
46
j
h
25
K
k
a
38
46
34
23
46
54
24
46
7
46
19
37
30
39
27
G
E
46 46
F
47
32
j
12
19
46
MAIN h
Unit
6
53
46
54
f
46
19
46
46
23
46
53
h
b
10
d
p
19
22
h
47
G
48
E
2
42
49
2-1
2-2
21
2-3
48
46" LCD
Panel Module Unit
5
B
46
17 40
X3
46
17
46
4
C
16
2-10
40
2-5
X3
C
X2
2-4
2-9
X1
46
A
48
2-6
2-7
A
50
17
52
2-7
9
5
X3
X1
43
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[4] CABINET PARTS (LC-46LE812E/LX812E)
!
!
1
1
2
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-9
2-10
4
5
6
7
8
9
10
11
12
13
14
15
16
17
19
20
21
22
23
24
25
27
28
29
30
31
32
33
34
35
37
38
39
40
41
42
43
46
47
48
49
50
52
53
54
55
57
58
59
60
61
62
63
CCABAC528WJ11
CCABAC528WJ13
CCABBB699WE14
Not available
Not available
Not available
Not available
Not available
Not available
Not available
Not available
Not available
GCOVAD816WJ1A
GCOVAD699WJ1A
GCOVAD710WJSA
GCOVAD711WJSA
GCOVAD709WJ1A
LANGKC720WJFW
LANGKC743WJFW
LANGKC744WJFW
LANGKC745WJFW
LANGKC746WJFW
LANGKC747WJFW
LANGKC811WJFW
LHLDKA011WJKZ
LHLDWA143WJKZ
LHLDWA294WJUZ
LHLDZA587WJKZ
LX-BZA170WJF9
LX-BZA364WJF7
NSFTZA362WJFW
PCLiCA004WJKZ
PMLT-A636WJZZ
PZETKA541WJKZ
PZETKA556WJKZ
QACCKA052WJPZ
QCNW-K976WJQZ
QCNW-K977WJQZ
QCNW-K978WJQZ
QCNW-K556WJQZ
QCNW-K572WJQZ
QCNW-K559WJQZ
QCNW-K570WJQZ
QCNW-K577WJQZ
QEARZ0057CEFW
QEARZA186WJZZ
RSP-ZA474WJZZ
RSP-ZA476WJZZ
TLABNC117WJZZ
XBPS730P06WS0
XBPS730P10WS0
XBPS830P06WS0
XBPS830P14WS0
XEBS840P10000
PSPAZC492WJKZ
PSPAGA889WJKZ
PSPAGA891WJKZ
PSPAGA892WJKZ
PZETKA563WJKZ
PCUSGA142WJKZ
TLABZC453WJZZ
PMLT-A637WJQZ
RCORFA020WJZZ
RCORFA023WJZZ
TLABZC596WJZZ
-
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
AD
AC
AC
AC
AC
AB
N
AC
AG
AE
AF
AK
AG
AR
AB
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
AA
AA
AA
N
AF
N
AE
AD
AD
N
N
N
N
AN
AK
N
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
J
J
J
J
J
J
P
J
P
P
P
P
J
J
J
P
P
J
J
J
J
P
P
P
P
J
J
J
P
J
P
J
J
J
P
P
P
P
J
J
P
Front Cabinet Ass'y (LC-46LE812E)
Front Cabinet Ass'y (LC-46LX812E)
Rear Cabinet Ass'y
Rear Cabinet
Terminal Label (Side)
Terminal Label (Bottom)
Himeron
Spacer
Insulation Sheet
Himeron, x4
Himeron
Himeron
Stand Cover
AC Cord Cover
Terminal Angle (Side)
Terminal Angle (Bottom)
ECO Switch Cover
Stand Angle
LCD Angle (Bottom-L)
LCD Angle (Bottom-R)
LCD Angle (Top-L)
LCD Angle (Top-R)
LCD Angle (B-C-A)
LCD Angle (B-C-B)
AC Cord Band
Wire Holder, x3
Wire Holder, x8
Spacer, x5
Screw (for VESA/Rear Cabinet Ass'y), x4
Screw (for Woofer), x4
Shaft (for PWB/Angle), x4
Nylon Rivet, x2
Gasket
Insulation Sheet (Power)
Insulation Sheet (ECO)
AC Cord
Connecting Cord (PD)
Connecting Cord (PL)
Connecting Cord (LB)
Connecting Cord (AS)
Connecting Cord (RA)
Connecting Cord (SP)
Connecting Cord (SB)
Connecting Cord (LW)
Earth Spring
Conductive Tape, x2
Speaker (L/R), x2
Speaker (Woofer)
Model Label
Screw (for PWB/Angle/LCD/Cabinet), x37
Screw (for Panel Angle), x5
Screw (for Rear Cabinet Ass'y), x17
Screw (for Rear Cabinet Ass'y)
Screw (for Speaker/Rear Cabinet Ass'y), x4
Spacer, x2
Spacer, x2
Spacer, x2
Spacer
Insulation Sheet (AC)
Rubber Bush
Panel Label
Gasket
Core
Core
Label (LC-46LX812E)
6
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[5] CABINET PARTS (LC-40LE822E/LU822E)
Note:
Be sure to attach this insulation sheet. (Ref No. 2-6, 25, 53)
Otherwise there is a risk of electric shock.
1
a
H
39
J
33
L
1-1
L
39
1-3
J
1-2
3
e
LOGO
Unit
f
ICON
Unit
p
b R/C,
LED
Unit
44
26
g
44
m
55
n
8
18
F
K
56
p
p
53
13
44
H
TOUCH
SENSOR
Unit
51
d
14
17
11
44
14
16
E
44
51
12
a
7
52
25
G
b
K
E
G
32
2-2
46
40" LCD
Panel Module Unit
2-1
2
C
X3
16
38
4
C
X1
X2
46
2-6
48
2-9
9
2-9
44
7
46
15
A
2-7
A
5
2-4
2-8
X3
2-3
19
2-5
44
16
16
47
B
44
38
e
10
k
49
p
34
20
22
45
d
40
23
49
h
30
44
n
36
44
F
j
50
28
44
h
44
44
21
45
44
k
37
17
B
16
POWER
j
Unit
31
m
44
44
f
27
29
44
MAIN
Unit
6
44
52
g
35
21
44
X3
X1
41
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[5] CABINET PARTS (LC-40LE822E/LU822E)
!
!
1
1
1-1
1-2
1-3
1-4
1-5
1-6
2
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
44
45
46
47
48
49
50
51
52
53
55
56
57
58
59
60
61
62
CCABAC522WJ11
CCABAC522WJ12
Not available
Not available
Not available
PSPAGA906WJZZ
PSPAZC495WJZZ
PSPAHC201WJZZ
CCABBB698WJ13
Not available
HiNDPD710WJSA
HiNDPD727WJSA
PSPAHC152WJ1Z
PSPAZC461WJZZ
PZETKA570WJKZ
PSPAHC159WJZZ
PSPAHC160WJZZ
PSPAHC194WJZZ
CPNLHA019WE11
GCOVAD696WJ1A
GCOVAD699WJ1A
GCOVAD706WJSA
GCOVAD711WJSA
GCOVAD709WJ1A
LANGKC719WJM1
LANGKC743WJFW
LANGKC744WJFW
LANGKC745WJFW
LANGKC746WJFW
LANGKC775WJM1
LHLDKA011WJKZ
LHLDWA143WJKZ
LHLDWA294WJUZ
LHLDZA587WJKZ
LX-BZA170WJF9
LX-BZA364WJF7
NSFTZA362WJFW
PCLiCA004WJKZ
PMLT-A636WJZZ
PZETKA548WJKZ
PZETKA556WJKZ
QACCKA052WJPZ
QCNW-K976WJQZ
QCNW-K977WJQZ
QCNW-K551WJQZ
QCNW-K978WJQZ
QCNW-K553WJQZ
QCNW-K554WJQZ
QCNW-K580WJQZ
QCNW-K556WJQZ
QCNW-K576WJQZ
QEARZ0057CEFW
QEARZA186WJZZ
RSP-ZA474WJZZ
RSP-ZA476WJZZ
TLABNC117WJZZ
XBPS730P06WS0
XBPS730P10WS0
XBPS830P06WS0
XBPS830P14WS0
XEBS840P10000
PSPAGA888WJZZ
PSPAZC492WJKZ
PSPAGA889WJKZ
PSPAGA891WJKZ
PZETKA563WJKZ
PCUSGA142WJKZ
PSPAZC494WJKZ
PSPAKA474WJKZ
TLABZC585WJZZ
TLABZC453WJZZ
PMLT-A637WJQZ
RCORFA023WJZZ
TLABZC597WJZZ
-
-
N
N
N
N
N
N
N
N
N
N
N
N
N
AE
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
AD
AC
AC
AC
AC
AB
N
AC
AG
AE
AF
N
N
N
N
N
N
N
N
N
N
N
N
N
AB
N
N
N
N
AA
AA
AA
N
AF
N
N
AE
AD
N
N
N
N
N
N
N
AK
N
P
P
P
P
P
P
P
P
P
J
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
J
J
J
J
J
J
P
J
P
P
P
P
J
J
P
J
P
P
P
P
P
J
P
P
P
P
J
J
J
P
J
P
P
J
J
P
P
P
P
P
P
P
J
P
Front Cabinet Ass'y (LC-40LE822E)
Front Cabinet Ass'y (LC-40LU822E)
Front Cabinet
R/C Decoration Cover
Front Decoration
Spacer
Spacer, x5
Himelon, x4
Rear Cabinet Ass'y
Rear Cabinet
Terminal Label (Side)
Terminal Label (Bottom)
Himelon
Spacer
Insulation Sheet
Himelon
Himelon
Himelon, x4
Glass Front Panel Ass'y
Stand Cover
AC Cord Cover
Terminal Angle (Side)
Terminal Angle (Bottom)
ECO Switch Cover
Stand Angle
LCD Angle (Bottom-L)
LCD Angle (Bottom-R)
LCD Angle (Top-L)
LCD Angle (Top-R)
VESA Angle, x2
AC Cord Band
Wire Holder, x5
Wire Holder, x3
Spacer, x5
Screw (for VESA/Rear Cabinet Ass'y), x4
Screw (for Woofer), x4
Shaft (for PWB/Angle), x4
Nylon Rivet, x2
Gasket
Insulation Sheet (Power)
Insulation Sheet (ECO)
AC Cord
Connecting Cord (PD)
Connecting Cord (PL)
Connecting Cord (RA)
Connecting Cord (LB)
Connecting Cord (SB)
Connecting Cord (SP)
Connecting Cord (RL)
Connecting Cord (AS)
Connecting Cord (LW)
Earth Spring
Conductive Tape, x2
Speaker (L/R), x2
Speaker (Woofer)
Model Label
Screw (for PWB/Angle/LCD/Cabinet), x39
Screw (for Panel Angle), x3
Screw (for Rear Cabinet Ass'y), x13
Screw (for Rear Cabinet Ass'y)
Screw (for Speaker), x4
Spacer, x4
Spacer, x2
Spacer, x2
Spacer, x2
Insulation Sheet (AC)
Rubber Bush, x2
Cooling Sheet
Spacer
Quattron Label
Plane Label
Gasket
Core
Label (LC-40LU822E)
8
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[6] CABINET PARTS (LC-46LE822E/LU822E)
Note:
Be sure to attach this insulation sheet. (Ref No. 2-6, 27, 57)
Otherwise there is a risk of electric shock.
1
H
a
41
J
35
L
1-5
1-5
1-4
L
41
1-1
1-5
1-3
J
1-2
3
e
LOGO
Unit
ICON
Unit
p
b R/C,
LED
Unit
f
g
8
28
F
19
18
46
19
46
11
46
23
46
46
55 15
19
47
19
37
G
24
h
25
j
K
51
30
46
a
7
34
h
b
10
d
p
36
22
e
h
47
38
46
23
46
54
k
39
46
27
56
E
19
46 46
14
F
32
j
12
19
46
46
MAIN h
Unit
6
53
46
54
B
j
33
57
29
13
19
g
m
31
H
53
47
m
46
d TOUCH
SENSOR
Unit
20
k
K
f
j
46
POWER
Unit
46
G
48
E
2
42
49
2-1
2-2
21
2-3
48
51
17 40
46" LCD
Panel Module Unit
B
X3
46
4
40
C
X2
A
2-7
X1
46
C
2-5
X3
48
2-6
A
2-9
50
17
52
16
2-4
2-8
46
46
17
5
2-9
9
9
X3
X1
43
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[6] CABINET PARTS (LC-46LE822E/LU822E)
!
!
1
1
1-1
1-2
1-3
1-4
1-5
1-6
2
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
46
47
48
49
50
51
52
53
54
55
56
57
59
60
61
62
63
64
65
66
CCABAC523WJ11
CCABAC523WJ12
Not available
Not available
Not available
PSPAGA907WJZZ
PSPAZC495WJZZ
PSPAHC201WJZZ
CCABBB699WE13
Not available
HiNDPD710WJSA
HiNDPD727WJSA
PSPAHC152WJ1Z
PSPAZC461WJZZ
PZETKA569WJKZ
PSPAHC159WJZZ
PSPAHC160WJZZ
PSPAHC194WJZZ
CPNLHA020WJ11
GCOVAD816WJ1A
GCOVAD699WJ1A
GCOVAD706WJSA
GCOVAD711WJSA
GCOVAD709WJ1A
LANGKC720WJFW
LANGKC743WJFW
LANGKC744WJFW
LANGKC745WJFW
LANGKC746WJFW
LANGKC747WJFW
LANGKC811WJFW
LHLDKA011WJKZ
LHLDWA143WJKZ
LHLDWA176WJUZ
LHLDWA294WJUZ
LHLDZA587WJKZ
LX-BZA170WJF9
LX-BZA364WJF7
NSFTZA362WJFW
PCLiCA004WJKZ
PMLT-A636WJZZ
PZETKA541WJKZ
PZETKA556WJKZ
QACCKA052WJPZ
QCNW-K976WJQZ
QCNW-K977WJQZ
QCNW-K978WJQZ
QCNW-K556WJQZ
QCNW-K572WJQZ
QCNW-K559WJQZ
QCNW-K580WJQZ
QCNW-K570WJQZ
QCNW-K577WJQZ
QEARZ0057CEFW
QEARZA186WJZZ
RSP-ZA474WJZZ
RSP-ZA476WJZZ
TLABNC117WJZZ
XBPS730P06WS0
XBPS730P10WS0
XBPS830P06WS0
XBPS830P14WS0
XEBS840P10000
PSPAGA888WJZZ
PSPAZC492WJKZ
PSPAGA889WJKZ
PSPAGA891WJKZ
PSPAGA892WJKZ
LANGFA776WJFW
PZETKA563WJKZ
PSPAKA474WJKZ
TLABZC586WJZZ
TLABZC453WJZZ
PCUSGA142WJKZ
PMLT-A637WJQZ
RCORFA020WJZZ
RCORFA023WJZZ
TLABZC597WJZZ
-
-
N
N
N
N
N
N
N
N
N
N
N
N
N
AE
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
AD
AC
AC
AC
AC
AC
AB
N
AC
AG
AE
AF
AK
AG
AR
AB
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
AA
AA
AA
N
AF
N
N
AE
AD
AD
N
N
N
N
N
N
N
AN
AK
N
P
P
P
P
P
P
P
P
P
J
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
J
J
J
J
J
J
J
P
J
P
P
P
P
J
J
J
P
P
J
P
J
J
J
P
P
P
P
J
J
J
P
J
P
P
J
J
J
P
P
P
P
P
P
P
J
J
P
Front Cabinet Ass'y (LC-46LE822E)
Front Cabinet Ass'y (LC-46LU822E)
Front Cabinet
R/C Decoration Cover
Front Decoration
Spacer
Double Side Tape, x3
Himeron, x4
Rear Cabinet Ass'y
Rear Cabinet
Terminal Label (Side)
Terminal Label (Bottom)
Himelon
Spacer
Insulation Sheet
Himelon
Himelon
Himelon, x4
Glass Front Panel Ass'y
Stand Cover
AC Cord Cover
Terminal Angle (Side)
Terminal Angle (Bottom)
ECO Switch Cover
Stand Angle
LCD Angle (Bottom-L)
LCD Angle (Bottom-R)
LCD Angle (Top-L)
LCD Angle (Top-R)
LCD Angle (B-C-A)
LCD Angle (B-C-B)
AC Cord Band
Wire Holder, x3
Wire Holder
Wire Holder, x6
Spacer, x5
Screw (for VESA/Rear Cabinet Ass'y), x4
Screw (for Woofer), x4
Shaft (for PWB/Angle), x4
Nylon Rivet, x2
Gasket
Insulation Sheet (Power)
Insulation Sheet (ECO)
AC Cord
Connecting Cord (PD)
Connecting Cord (PL)
Connecting Cord (LB)
Connecting Cord (AS)
Connecting Cord (RA)
Connecting Cord (SP)
Connecting Cord (RL)
Connecting Cord (SB)
Connecting Cord (LW)
Earth Spring
Conductive Tape, x2
Speaker (L/R), x2
Speaker (Woofer)
Model Label
Screw (for PWB/Angle/LCD/Cabinet), x39
Screw (for Panel Angle), x5
Screw (for Rear Cabinet Ass'y), x17
Screw (for Rear Cabinet Ass'y)
Screw (for Speaker/Rear Cabinet Ass'y), x4
Spacer, x4
Himelon, x2
Spacer, x2
Spacer, x2
Spacer
BL Chassis Support Angle
Insulation Sheet (AC)
Spacer
Quattron Label
Plane Label
Rubber Bush
Gasket
Core
Core
Label (LC-46LU822E)
10
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[7] CABINET PARTS (LC-52LE822E)
Note:
Be sure to attach this insulation sheet. (Ref No. 2-6, 28, 58)
Otherwise there is a risk of electric shock.
1
H
a
36
42
J
L
1-1
L
42
1-3
J
1-2
3
e
LOGO
Unit
ICON
Unit
p
f
g
b R/C,
LED
Unit
21
m
F
47
29
POWER
Unit
47
k
62
32
30
15
d TOUCH
SENSOR
H
Unit
54
g
48
B
24
19
60
47
54
28
G
56
47
31
a
40
47
39
7
47
60
12
55
25
h
k
E
47
61
48
47
14
16
57
33
6
47
19
47
MAIN
n
Unit
47
19
17
F
j
m
47
24
47
35
b
h
d
38
26
52
G
n
60
47
43
34
47
13 47
f
23
37
60
55
j
p
K
47
58
p
8
p
e
K
E
48
2
50
2-1
52" LCD
Panel Module Unit
52
2-2
49
41
2-5
C
X3
19
47
19
47
47
19
53
41
C
X2
X3
X1
2-7
X1
4
5
2-8
A
X3
49
2-6
A
51
2-9
2-9
11
11
49
18
2-4
B
47
2-3
22
44
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[7] CABINET PARTS (LC-52LE822E)
!
!
1
1-1
1-2
1-3
1-4
1-5
1-6
2
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
3
4
5
6
7
8
11
12
13
14
15
16
17
18
19
21
22
23
24
25
26
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
47
48
49
50
51
52
53
54
55
56
57
58
60
61
62
63
64
65
66
67
68
CCABAC524WJ31
Not available
Not available
Not available
PSPAGA908WJZZ
PSPAZC528WJZZ
PSPAHC201WJZZ
CCABBB700WE12
Not available
HiNDPD710WJSA
HiNDPD727WJSA
PSPAHC152WJ1Z
PSPAZC461WJZZ
PZETKA569WJKZ
PSPAHC159WJZZ
PSPAHC160WJZZ
PSPAHC194WJZZ
PSPAHA565WJZZ
CPNLHA021WJ11
GCOVAD816WJ1A
GCOVAD699WJ1A
GCOVAD706WJSA
GCOVAD711WJSA
GCOVAD709WJ1A
LANGKC720WJFW
LANGKC743WJFW
LANGKC744WJFW
LANGKC745WJFW
LANGKC746WJFW
LANGKC747WJFW
LANGKC811WJFW
LHLDKA011WJKZ
LHLDWA143WJKZ
LHLDZA587WJKZ
LX-BZA170WJF9
LX-BZA364WJF7
NSFTZA362WJFW
PCLiCA004WJKZ
PMLT-A636WJZZ
PZETKA541WJKZ
PZETKA556WJKZ
QACCKA052WJPZ
QCNW-K976WJQZ
QCNW-K977WJQZ
QCNW-K978WJQZ
QCNW-K556WJQZ
QCNW-K562WJQZ
QCNW-K579WJQZ
QCNW-K574WJQZ
QCNW-K565WJQZ
QCNW-K577WJQZ
QEARZ0057CEFW
QEARZA186WJZZ
RSP-ZA474WJZZ
RSP-ZA475WJZZ
TLABNC117WJZZ
XBPS730P06WS0
XBPS730P10WS0
XBPS830P06WS0
XBPS830P14WS0
XEBS840P10000
PSPAGA888WJZZ
PSPAZC492WJKZ
PSPAGA889WJKZ
PSPAGA891WJKZ
PSPAGA892WJKZ
LANGFA776WJFW
PZETKA563WJKZ
LHLDWA294WJUZ
LHLDWA176WJUZ
PCUSGA142WJKZ
PSPAKA474WJKZ
TLABZC586WJZZ
TLABZC453WJZZ
PMLT-A637WJQZ
PSLDPA108WJKZ
RCORFA023WJZZ
-
-
N
N
N
N
N
N
N
N
N
N
N
N
AE
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
AD
AC
AC
AC
AB
N
AC
AG
AE
AF
AK
AF
AE
AR
AB
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
AA
AA
AA
N
AF
N
N
AE
AD
AD
N
N
AC
AC
N
N
N
N
N
N
AK
P
P
P
P
P
P
P
P
J
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
J
J
J
J
J
P
J
P
P
P
P
J
J
J
P
P
J
J
J
J
J
P
P
P
P
J
J
J
P
J
P
P
J
J
J
P
P
J
J
P
P
P
P
P
P
J
Front Cabinet Ass'y
Front Cabinet
R/C Decoration Cover
Front Decoration
Spacer
Spacer, x4
Himeron, x4
Rear Cabinet Ass'y
Rear Cabinet
Terminal Label (Side)
Terminal Label (Bottom)
Himelon
Spacer
Insulation Sheet
Himelon
Himelon
Himelon, x4
Himelon
Glass Front Panel Ass'y
Stand Cover
AC Cord Cover
Terminal Angle (Side)
Terminal Angle (Bottom)
ECO Switch Cover
Stand Angle
LCD Angle (Bottom-L)
LCD Angle (Bottom-R)
LCD Angle (Top-L)
LCD Angle (Top-R)
LCD Angle (B-C-A)
LCD Angle (B-C-B)
AC Cord Band
Wire Holder, x6
Spacer, x5
Screw (for VESA/Rear Cabinet Ass'y), x4
Screw (for Woofer), x4
Shaft (for PWB/Angle), x4
Nylon Rivet, x2
Gasket
Insulation Sheet (Power)
Insulation Sheet (ECO)
AC Cord
Connecting Cord (PD)
Connecting Cord (PL)
Connecting Cord (LB)
Connecting Cord (AS)
Connecting Cord (RA)
Connecting Cord (SP)
Connecting Cord (SB)
Connecting Cord (RL)
Connecting Cord (LW)
Earth Spring
Conductive Tape, x2
Speaker (L/R), x2
Speaker (Woofer)
Model Label
Screw (for PWB/Angle/LCD Angle/Cabinet), x43
Screw (for LCD/Front Cabinet Ass'y), x6
Screw (for Raer Cabinet), x19
Screw (for Rear Cabinet)
Screw (for Speaker/Rear Cabinet Ass'y), x4
Spacer, x4
Himelon, x2
Spacer, x2
Spacer, x2
Spacer
BL Chassis Support Angle, x2
Insulation Sheet (AC)
Wire Holder, x6
Wire Holder
Rubber Bush
Spacer
Quattron Label
Panel Label
Gasket
Shield Tape A, x2
Core
12
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[8] SUPPLIED ACCESSORIES
X8
Remote control unit ( x 1)
X13
"AAA" size alkaline battery ( x 2)
X4
Cable clamp ( x 1)
X6
RGB component cable ( x 1)
X5
SCART cable ( x 1)
X7
AV cable ( x 1)
X2 Stand unit ( x 1)
X1 Stand Support Ass'y
X12 Operation manual
X14 Caution Card
X15 Warranty Card
X16 Warranty Card
X17 Operation Manual
X3 Stand Screw Ass'y
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[8] SUPPLIED ACCESSORIES
X1
X1
X2
X2
X2
X2
X3
X4
X5
X6
X7
X8
X8
X12
X13
X14
X15
X16
X17
CANGKC707WJ01
CANGKC708WJ01
CDAi-A653WJ01
CDAI-A653WJ04
CDAi-A654WJ02
CDAI-A654WJ04
CX-BZA363WJ01
LHLDWA298WJKA
QCNWGA158WJPZ
QCNWGA159WJPZ
QCNWGA160WJPZ
RRMCGA841WJSA
RRMCGA857WJSA
TiNS-E678WJZZ
Not available
TCAUSA034WJZZ
TGAN-B078WJZZ
TGAN-B079WJZZ
TiNS-E679WJZZ
AD
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
P
P
P
P
P
P
P
J
P
P
P
P
P
P
P
P
P
P
Stand Support Ass'y (LC-40LE810E/LX810E/LE822E/LU822E)
Stand Support Ass'y (LC-46LE812E/LX812E/LE822E/LU822E, LC-52LE822E)
Stand Unit (LC-40LE812E/LE822E)
Stand Unit (LC-40LX812E/LU822E)
Stand Unit (LC-46LE812E/LE822E, LC-52LE822E)
Stand Unit (LC-46LX812E/LU822E)
Stand Screw Ass'y
Cable Clamp
SCART Cable
RGB Component Cable
AV Cable
Remote Control Unit (LC-40/46/52LE822E, LC-40/46LU822E)
Remote Control Unit (LC-40/46LE812E, LC-40/46LX812E)
Operation Manual
"AAA" size alkaline battery, x2
Caution Card
Warranty Card
Warranty Card
Operation Manual
13
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[9] PACKING PARTS (NOT REPLACEMENT ITEM) (LC-40LE812E/LX812E/LE822E/LU822E)
S8
X14
X15
X16
X17
S2
X8
S10
X3
S7
X4
X13
S5
X5
S3
X1
X6
X7
S5
S5
S5
S4
X2
S6
S6
S1
S11
14
S8
X12
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[9] PACKING PARTS (NOT REPLACEMENT ITEM) (LC-40LE812E/LX812E/LE822E/LU822E)
S1
S1
S2
S3
S4
S4
S5
S6
S7
S8
S10
S11
SPAKCF708WJZZ
SPAKCF712WJZZ
SPAKPB475WJZZ
SPAKPB526WJZZ
SPAKPB528WJZZ
SPAKPB561WJZZ
SPAKXC920WJZZ
SPAKXC925WJZZ
SSAKAA009WJZZ
SSAKAA111WJZZ
SSAKKA008WJZZ
TLABM5584BMZZ
-
N
N
N
N
N
N
N
N
N
N
N
N
-
Packing Case (LC-40LE822E/LX822E)
Packing Case (LC-40LE812E/LX812E)
Wrapping Paper
Wrapping Paper, x2
Wrapping Paper (LC-40LE812E)
Wrapping Paper (LC-40LX812E)
Packing Add. (Top)
Packing Add. (Bottom)
Polyethylene Bag
Polyethylene Bag, x2
Polyethylene Bag
Case No. Label
15
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[10] PACKING PARTS (NOT REPLACEMENT ITEM) (LC-46LE812E/LX812E/LE822E/LU822E)
S9
X14
X15
X16
X17
S6
X8
S1
S9
X12
S11
X3
X6
X7
S6
S6
S3
S5
X2
X5
S8
X4
X13
S6
S7
S4
X1
S7
S7
S7
S12
S2
16
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[10] PACKING PARTS (NOT REPLACEMENT ITEM) (LC-46LE812E/LX812E/LE822E/LU822E)
S1
S1
S2
S3
S4
S5
S5
S6
S7
S8
S9
S11
S12
SPAKCF707WJZZ
SPAKCF711WJZZ
SPAKCF496WJZZ
SPAKPB477WJZZ
SPAKPB527WJZZ
SPAKPB529WJZZ
SPAKPB562WJZZ
SPAKXC921WJZZ
SPAKXC926WJZZ
SSAKAA009WJZZ
SSAKAA111WJZZ
SSAKKA008WJZZ
TLABM5584BMZZ
-
N
N
N
N
N
N
N
N
N
N
N
N
N
-
Packing Case (Top) (LC-46LE812E/LX812E)
Packing Case (Top) (LC-46LE812E/LX812E)
Packing Case (Bottom)
Wrapping Paper
Wrapping Paper, x2
Wrapping Paper (LC-46LE812E)
Wrapping Paper (LC-46LX812E)
Packing Add. (Top)
Packing Add. (Bottom)
Polyethylene Bag
Polyethylene Bag, x2
Polyethylene Bag
Case No. Label
17
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
[11] PACKING PARTS (NOT REPLACEMENT ITEM) (LC-52LE822E)
S9
X14
X15
X16
X17
S1
X8
S6
S9
X12
S8
X4
X13
S6
S6
X5
S11
X3
S6
S3
S5
X2
S7
S4
X1
S7
S7
S7
S12
S2
18
X6
X7
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E (1st Edition)
NO.
PARTS CODE
PRICE NEW PART
RANK MARK DELIVERY
DESCRIPTION
[11] PACKING PARTS (NOT REPLACEMENT ITEM) (LC-52LE822E)
S1
S2
S3
S4
S5
S6
S7
S8
S9
S11
S12
SPAKCF706WJZZ
SPAKCF497WJZZ
SPAKPB478WJZZ
SPAKPB527WJZZ
SPAKPB529WJZZ
SPAKXC922WJZZ
SPAKXC927WJZZ
SSAKAA009WJZZ
SSAKAA111WJZZ
SSAKKA008WJZZ
TLABM5584BMZZ
-
N
N
N
N
N
N
N
N
N
N
N
-
Packing Case (Top)
Packing Case (Bottom)
Wrapping Paper
Wrapping Paper, x2
Wrapping Paper
Packing Add. (Top)
Packing Add. (Bottom)
Polyethylene Bag
Polyethylene Bag, x2
Polyethylene Bag
Case No Label
J
J
J
J
J
J
J
J
Main Unit to LCD Control Unit (LW)
Main Unit to Power Unit (PL)
Main Unit to Power Unit (PD)
Main Unit to Power (LED Drive) Unit (LB)
Main Unit to R/C, LED Unit (RA)
Main Unit to Speaker (SP)
Main Unit to Icon Unit (RL) (LC-40/46/52LE822E, LC-40/46LU822E)
Main Unit to Woofer (SB)
[12] SERVICE JIGS (USE FOR SERVICING)
N
N
N
N
N
N
N
N
QCNW-G616WJQZ
QCNW-G625WJQZ
QCNW-H184WJQZ
QCNW-H185WJQZ
QCNW-K594WJQZ
QCNW-K595WJQZ
QCNW-K596WJQZ
QCNW-K597WJQZ
BK
AP
AX
AV
N
N
N
N
19
LC-40/46LE812E, LC-40/46LX812E, LC-40/46/52LE822E, LC-40/46LU822E
COPYRIGHT © 2010 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No Part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
May. 2010
SH. DS
SHARP CORPORATION
AV Systems Group
CS Promotion Center
Yaita,Tochigi 329-2193, Japan