Download HDMI 1 - Datatail
Transcript
C English Français AV Receiver/Ampli-tuner audio-vidéo Easy Setup Guide Manuel de configuration rapide 1 Preparation AV Receiver Accessories Check that the following accessories are supplied with the product. Remote control Batteries (AAA, R03, UM-4) (x2) Insert the batteries the right way round. Easy Setup Guide English YPAO microphone Power cable *The supplied power cable varies depending on the region of purchase. AM antenna FM antenna *The supplied FM antenna varies depending on the region of purchase. This document explains how to set up a 5.1- or 7.1-channel system and play back surround sound from a BD/DVD on the unit. CD-ROM (Owner’s Manual) Safety Brochure Easy Setup Guide To reduce the impact on natural resources, the Owner’s Manual for this product is supplied on CD-ROM. For more information about this product, refer to the Owner’s Manual on the supplied CD-ROM. PDF versions of this guide and “Owner’s Manual” can be downloaded from the following website. http://download.yamaha.com/ [For U.S. customers only] Visit the following website for additional information, FAQ’s, downloads such as “Owner’s Manual” and product updates. http://usa.yamaha.com/support/ Cables required for connections The following cables (not supplied) are required to build the system described in this document. • Speaker cables (depending on the number of speakers) • HDMI cable (x2) • Audio pin cable (x1) • Digital optical cable (x1) (not required if your TV supports ARC [Audio Return Channel]) En 1 2 Placing speakers Set up the speakers in the room using the following diagram as a reference. For information on other speaker systems, refer to “Owner’s Manual”. 5.1-channel system 7.1-channel system 1 9 1 2 2 3 4 5 10° to 30° 9 3 10° to 30° 6 7 30 cm (1 ft) or more 1 Front speaker (L) 4 5 10° to 30° 10° to 30° 2 Front speaker (R) 3 Center speaker 4 Surround speaker (L) 5 Surround speaker (R) 6 Surround back speaker (L) 7 Surround back speaker (R) 9 Subwoofer 2 En 3 Connecting speakers/subwoofer • Under its default settings, the unit is configured for 8-ohm speakers. When connecting 6-ohm speakers, set the unit’s speaker impedance to “6 Ω MIN”. For details, see “Setting the speaker impedance” in “Owner’s Manual”. 1 Connect the front speakers (1/2) to the FRONT (//\) terminals. • Use a subwoofer equipped with built-in amplifier. • Before connecting the speakers, remove the unit’s power cable from the AC wall outlet and turn off the subwoofer. • Ensure that the core wires of the speaker cable do not touch each other or come into contact with the unit’s metal areas. This may damage the unit or the speakers. If the speaker cables short circuit, “Check SP Wires” will appear on the front display when the unit is turned on. Connect the center speaker (3) to the CENTER terminal. EXTRA SP EXTRA SP ZONE2/F PRESENCE ZONE2/F PRESENCE The unit (rear) The unit (rear) SPEAKERS FRONT CENTER SPEAKERS SURROUND FRONT SURROUND BACK B -AMP SINGLE 1 ■ Connecting speaker cables 2 CENTER SURROUND SURROUND BACK B -AMP SINGLE 1 2 2 SUBWOOFER SUBWOOFER Speaker cables have two wires. One is for connecting the negative (–) terminals of the unit and the speaker, and the other is for the positive (+) terminals. If the wires are colored to prevent confusion, connect the black wire to the negative and the other wire to the positive terminals. a Remove approximately 10 mm (3/8”) of insulation from the ends of the speaker cable and twist the bare wires of the cable firmly together. + (red) b 1 c FR ON 2 1 2 T d a 9 3 9 3 – (black) b Loosen the speaker terminal. 4 5 4 5 c Insert the bare wires of the cable into the gap on the side (upper right or bottom left) of the terminal. d Tighten the terminal. Using a banana plug (U.S.A., Canada and Australia models only) a Tighten the speaker terminal. Banana plug a FR ON T b b Insert a banana plug into the end of the terminal. En 3 3 Connect the surround speakers (4/5) to the SURROUND (//\) terminals. 4 Connect the subwoofer (9) to the SUBWOOFER PRE OUT (1) jack. • Use a subwoofer equipped with built-in amplifier. EXTRA SP EXTRA SP EXTRA SP ZONE2/F PRESENCE ZONE2 F PRESENCE The unit (rear) SPEAKERS CENTER Connect the surround back speakers (6/7) to the SURROUND BACK (//\) terminals. ZONE2/F PRESENCE The unit (rear) FRONT For 7.1-channel system The unit (rear) SPEAKERS SURROUND FRONT SURROUND BACK BI-AMP SINGLE 1 CENTER SPEAKERS SURROUND FRONT SURROUND BACK B -AMP SINGLE 1 CENTER SURROUND SURROUND BACK/BI AMP SI GLE 1 2 2 2 SUBWOOFER SUBWOOFER SUBWOOFER Audio pin cable 1 9 4 2 1 3 9 5 4 2 1 3 9 5 En 3 4 5 6 4 2 7 1 4 Connecting external devices TV Audio out (optical) HDMI in HDMI out HDMI HDMI BD/DVD player OPTICAL Connect external devices to the unit. a Connect a BD/DVD player to the unit with an HDMI cable. If the BD/DVD player is currently connected to the TV directly with an HDMI cable, disconnect the cable from the TV and connect it to this unit. b Connect a TV to the unit with the other HDMI cable. HDMI O b c a HDMI HDMI OUT jack HD c Connect a TV to the unit with a digital optical cable. This connection is required to play back TV audio on the unit. This connection is not required if your TV supports ARC (Audio Return Channel). HDMI d Connect the supplied power cable to the unit and then to an AC wall outlet. HDMI O T ( H 1 • For information on how to connect radio antennas or other external devices, see “PREPARATIONS” in “Owner’s Manual”. HDMI 1 jack ) ARC O T IGGER OU 12 0 1A DC OUT V A NETWORK HD (NET) HDMI OUT HDMI 2 HDMI 3 HDMI 4 HDMI 5 (BD DV IN 2 Turn on the unit, the TV and the BD/DVD player. 3 Use the TV remote control to change the TV input to video from the unit. AC N ARC UT EXTRA SP ZONE2 F PRESENCE OPT CAL REMOTE O TI AL (TV) AV4 AM V DEO FM (TV) AV4 COM ONENT V DEO C AXI L (RAD O) d PR ANTENNA AV3 Y PR PB SPEAKERS To an AC wall outlet PB AV 4 (OPTICAL) jack AV2 V DEO V DEO FRONT CENTER SURROUND SURROU D BACK B -AMP O TI AL Y AV 1 MONITOR OUT OM ONENT V DEO S NGLE 1 2 AUD O 1 AU IO 2 ONE 2 AV 5 AV 6 AV OUT UBWOO ER PRE OUT ONE OU The unit (rear) MAIN ZONE PURE D RECT Turn on the unit ZONE 2 ZONE CONTROL INFO MEMORY PR SET INPUT FM AM PHONES YPAO MIC TONE CONTROL TV • By connecting a TV to the unit with an HDMI cable, you can configure the unit’s settings with the menu displayed on the TV. In addition, you can select the on-screen menu language from English (default), Japanese, French, German, Spanish, Russian, Italian and Chinese. For details, refer to “Owner’s Manual”. In this guide, illustrations of English menu screens are used as examples. TUNING VOLUME SCENE BD/DVD S LENT CINEMA The connections are complete. Proceed to the next page to optimize the speaker settings. NET RAD O V DEO AUX PROGRAM STRAIGHT HDMI/ MHL V 1A VIDEO V 2 1A The unit (front) En 5 5 Optimizing the speaker settings automatically (YPAO) 1 The following screen appears on the TV. The Yamaha Parametric room Acoustic Optimizer (YPAO) function detects speaker connections, measures the distances from them to your listening position(s), and then automatically optimizes the speaker settings, such as volume balance and acoustic parameters, to suit your room. • During the measuring process, test tones are output at high volume. Ensure that the test tones do not frighten small children. Also, refrain from using this function at night when it may be a nuisance to others. Connect the YPAO microphone to the YPAO MIC jack on the front panel. RECEIVER SOURCE RECEIVER HDMI 1 2 3 4 • During the measuring process, you cannot adjust the volume. 5 V AUX • During the measuring process, keep the room as quiet as possible. • Do not connect headphones. AV 1 2 3 5 6 1 4 TUNER USB NET AUDIO • Do not stand between the speakers and the YPAO microphone during the measurement process (about 3 minutes). • Move to the corner of the room or leave the room. MA N 2 ZONE 2 • To cancel the operation, disconnect the YPAO microphone before starting the measurement. SCENE BD DV DVD Preparing for YPAO Turn on the subwoofer and set the volume to half. If the cross-over frequency is adjustable, set it to maximum. TV NET PROGRAM The unit (front) MUTE RADIO YPAO MIC TOP MENU To start the measurement, use the cursor keys to select “Measure” and press ENTER. POP UP/MENU ON SCREEN The measurement will start in 10 seconds. OPT ON Cursor keys ENTER RETURN ENTER VOLUME 2 VOLUME CROSSOVER/ HIGH CUT RETURN The following screen appears on the TV when the measurement finishes. DISPLAY BAND MODE TUNING PRESET SUR DECODE STRAIGHT MIN MAX MIN MAX MOV E MUS C NFO SLEEP ENHANCER PURE DIRECT YPAO microphone 1 2 5 6 9 0 3 4 8 MEMORY 10 ENT TV NPUT TV VOLL Ear height Place the YPAO microphone at your listening position (same height as your ears). We recommend the use of a tripod as a microphone stand. You can use the tripod screws to fix the microphone in place. 6 En MUTE TV CH CODE SET • If the cursor keys do not work, press RECEIVER and then use the cursor keys. • If any error message (such as E-1) or warning message (such as W-2) appears, see “Error messages” or “Warning messages” in “Owner’s Manual”. • If the warning message “W-1:Out of Phase” appears, see “If “W-1:Out of Phase” appears” (next page). 3 4 Use the cursor keys to select “Save/Cancel” and press ENTER. Use the cursor keys to select “SAVE” and press ENTER. If “W-1:Out of Phase” appears Follow the procedure below to check the speaker connections. a Use the cursor keys to select “Result” and press ENTER. b Use the cursor keys to select “Wiring”. c Check the cable connections (+/–) of the speaker that was identified as being “Reverse” in the warning message. If the speaker is connected correctly: Depending on the type of speakers or room environment, this message may appear even if the speakers are connected correctly. In this case, you can ignore the message. 5 Press RETURN and proceed to step 3. Disconnect the YPAO microphone from the unit. This completes optimization of the speaker settings. If the speaker is connected incorrectly: Turn off the unit, reconnect the speaker cable, and then try YPAO measurement again. • The YPAO microphone is sensitive to heat, so should not be placed anywhere where it could be exposed to direct sunlight or high temperatures (such as on top of AV equipment). En 7 6 Playing back a BD/DVD Now let’s play back a BD/DVD. We recommend playing back multichannel audio (5.1-channel or more) to feel surround sound produced by the unit. Many more features! 1 VOL HDMI1 RECEIVER SOURCE Press HDMI 1 to select “HDMI 1” as the input source. L SL SW C R SR HDMI HDMI 1 1 5 V AUX AV 1 2 3 4 AUDIO 5 6 1 TUNER USB NET MA N 2 2 3 Start playback on the BD/DVD player. Press STRAIGHT repeatedly to select “STRAIGHT”. STRAIGHT SCENE TV NET PROGRAM MUTE RADIO VOLUME VOLUME 4 L SL SW C R SR Press VOLUME to adjust the volume. VOL TOP MENU Volume -30.0dB POP UP/MENU ON SCREEN OPTION L SL SW C R SR This completes the basic setup procedure. ENTER RETURN If surround sound is not working DISPLAY BAND MODE TUNING PRESET SUR DECOD MOV E MUS C NFO SLEEP 1 2 5 6 9 0 STRA GHT Sound is only being output from the front speakers during multichannel audio playback 4 Check the digital audio output setting on the BD/DVD player. 8 It may be set to 2-channel output (such as PCM). ENHANCER PURE DIRECT 3 STRAIGHT MEMORY 10 ENT TV No sound is coming from a specific speaker NPUT TV VOLL MUTE TV CH CODE S T Please refer to “Owner’s Manual” on the supplied CD-ROM to help you get the most out of the unit. Connecting other playback devices Connect audio devices (such as CD player), game consoles, camcorders, and many others. Selecting the sound mode VOL ZONE 2 BD DV DVD The unit has various other functions. See “Troubleshooting” in “Owner’s Manual”. Select the desired sound program (CINEMA DSP) or surround decoder suitable for movies, music, games, sports programs, and other uses. Playing back from iPod By using a USB cable supplied with iPod, you can enjoy iPod music on the unit. ■ Listening to FM/AM radio ■ Playing back music stored on a USB storage device ■ Playing back the network contents ■ Selecting the input source and favorite settings at once For more information, see “What you can do with the unit”. 8 En 1 Préparation Ampli-tuner audio-vidéo Accessoires Vérifiez que les accessoires suivants sont fournis avec le produit. Télécommande Piles (AAA, R03, UM-4) (x2) Insérez les piles comme indiqué. Manuel de configuration rapide Microphone YPAO Câble d’alimentation *Le câble d’alimentation fourni dépend de la région d’achat. Antenne AM Antenne FM Français * L’antenne FM fournie dépend de la région d’achat. Ce document décrit la configuration d’un système à 5.1 ou 7.1 voies et explique comment restituer le son d’ambiance d’un disque BD/DVD sur l’unité. Afin de préserver l’environnement, le Mode d’emploi de ce produit est fourni sur CD-ROM. Pour en savoir plus sur ce produit, reportez-vous au Mode d’emploi fourni sur CD-ROM. Pour télécharger ce guide ainsi que le « Mode d’emploi » au format PDF, rendez-vous sur le site Web suivant : http://download.yamaha.com/ CD-ROM (Mode d’emploi) Brochure sur la sécurité Manuel de configuration rapide Câbles requis pour les raccordements Les câbles suivants (non fournis) sont requis pour l’installation du système décrit dans le présent document. • Câbles d’enceintes (en fonction du nombre d’enceintes) • Câble HDMI (x2) • Câble de broche audio (x1) • Câble optique numérique (x1) (inutile si votre téléviseur prend en charge la fonction ARC [Audio Return Channel]) Fr 1 2 Installation des enceintes Installez les enceintes dans la pièce en vous reportant au diagramme suivant. Pour obtenir des informations sur les autres systèmes d’enceinte, consultez le « Mode d’emploi ». Système à 5.1 voies Système à 7.1 voies 1 9 1 2 2 3 4 5 10° à 30° 9 3 10° à 30° 6 7 30 cm ou plus 1 Enceinte avant (G) 4 5 10° à 30° 10° à 30° 2 Enceinte avant (D) 3 Enceinte centrale 4 Enceinte Surround (G) 5 Enceinte Surround (D) 6 Enceinte Surround arrière (G) 7 Enceinte Surround arrière (D) 9 Subwoofer 2 Fr 3 Raccordement des enceintes/du caisson de graves • L’unité est configurée pour des enceintes 8 ohms par défaut. Lorsque vous raccordez des enceintes 6 ohms, réglez l’impédance d’enceinte de l’unité sur « 6 Ω MIN ». Pour plus d’informations, reportez-vous à la section « Réglage de l’impédance des enceintes » du « Mode d’emploi ». 1 Raccordez les enceintes avant (1/2) aux bornes FRONT (//\). 2 Raccordez l’enceinte centrale (3) à la borne CENTER. • Utilisez un caisson de graves équipé d’un amplificateur intégré. • Avant de raccorder les enceintes, retirez le câble d’alimentation de l’unité de la prise secteur et éteignez le caisson de graves. • Veillez à ce que les fils conducteurs du câble de l’enceinte ne se touchent pas ou n’entrent pas en contact avec les parties métalliques de l’unité. Ce contact risque d’endommager l’unité ou les enceintes. Si un court-circuit survient au niveau des câbles de l’enceinte, le message « Check SP Wires » apparaît sur l’afficheur de la face avant lors de la mise sous tension de l’unité. EXTRA SP EXTRA SP ZONE2/F PRESENCE ZONE2/F PRESENCE L’unité (arrière) L’unité (arrière) SPEAKERS FRONT CENTER SPEAKERS SURROUND SINGLE 1 n Raccordement des câbles d’enceinte 2 SUBWOOFER O SUBWOOFER O + (rouge) b Desserrez la borne d’enceinte. b 1 CENTER SURROUND SURROUND BACK B -AMP SINGLE 1 2 Les câbles d’enceinte sont composés de deux fils. L’un se connecte aux bornes négatives (-) de l’appareil et de l’enceinte, et l’autre aux bornes positives (+). Si les fils sont de couleurs différentes afin d’éviter toute confusion, connectez le fil de couleur noire aux bornes négatives et l’autre fil aux bornes positives. a Dénudez les extrémités du câble d’enceinte sur environ 10 mm, puis torsadez fermement les brins dénudés du câble. FRONT SURROUND BACK B -AMP 2 1 2 c FR ON T 9 d 3 9 3 a – (noir) 4 5 4 5 c Insérez les fils dénudés du câble dans l’écartement sur le côté (supérieur droit ou inférieur gauche) de la borne. d Serrez la borne. Utilisation d’une fiche banane (Modèles destinés aux États-Unis, au Canada et à l’Australie uniquement) a Serrez la borne d’enceinte. b Insérez la fiche banane dans l’extrémité de la borne. Fiche banane a FR ON T b Fr 3 3 Raccordez les enceintes d’ambiance (4/5) aux bornes SURROUND (//\). 4 Raccordez le subwoofer (9) à la prise SUBWOOFER PRE OUT (1). • Utilisez un subwoofer équipé d’un amplificateur intégré. EXTRA SP EXTRA SP EXTRA SP ZONE2/F PRESENCE ZONE2 F PRESENCE L’unité (arrière) SPEAKERS CENTER Raccordez les enceintes surround arrière (6/7) aux bornes SURROUND BACK (//\). ZONE2/F PRESENCE L’unité (arrière) FRONT Pour le système à 7.1 voies L’unité (arrière) SPEAKERS SURROUND FRONT SURROUND BACK BI-AMP SINGLE 1 CENTER SPEAKERS SURROUND FRONT SURROUND BACK B -AMP SINGLE 1 CENTER SURROUND SURROUND BACK/BI AMP SI GLE 1 2 2 2 SUBWOOFER SUBWOOFER SUBWOOFER Câble de broche audio 1 9 4 2 1 3 9 5 4 2 1 3 9 5 Fr 3 4 5 6 4 2 7 1 4 Raccordement des appareils externes a Raccordez un lecteur BD/DVD à l’unité au moyen d’un câble HDMI. Si le lecteur BD/DVD est actuellement directement raccordé au téléviseur à l’aide d’un câble HDMI, débranchez ce câble du téléviseur et raccordez-le à cette unité. Téléviseur Sortie audio (optique) Entrée HDMI Sortie HDMI HDMI HDMI Lecteur BD/DVD OPTICAL Raccordez les appareils externes à l’unité. b Raccordez un téléviseur à l’unité au moyen de l’autre câble HDMI. HDMI O b c a HDMI Prise HDMI OUT HD c Raccordez un téléviseur à l’unité au moyen d’un câble optique numérique. Ce raccordement est nécessaire si vous souhaitez restituer le son TV sur l’unité. Ce raccordement n’est pas nécessaire si votre téléviseur prend en charge la fonction ARC (Audio Return Channel). HDMI d Raccordez le câble d’alimentation à une prise électrique murale. HDMI O T ( H I1 Prise HDMI 1 ) ARC O T IGGER OU 12 0 1A DC OUT V A NETWORK HD (NET) HDM OUT HDMI 2 HDMI HDMI 4 HDMI 5 (BD DV IN AC N ARC UT EXTRA SP ZONE2 F PRESENCE OPT CAL REMOTE O TI AL (TV) AV4 AM V DEO FM (TV) AV4 COMPO ENT V DEO C AXI L (RAD O) d PR ANTENNA AV3 Y Prise AV 4 (OPTICAL) P PB Branchement sur une prise secteur SPEAKERS PB AV2 V DEO V DEO FRONT CENTER SURROUND SURROUND BACK B -AMP O TI AL Y AV 1 MONITOR OUT COM ONENT V DEO S NGLE 2 3 • Pour plus d’informations sur le raccordement des antennes radio ou des autres appareils externes, reportez-vous à la section « PRÉPARATION » du « Mode d’emploi ». Mettez sous tension, l’unité, le téléviseur et le lecteur BD/DVD. Utilisez la télécommande du téléviseur pour changer la source d’entrée du téléviseur et afficher l’image à partir de l’unité. 2 AUD O 1 AUD O 2 ONE 2 AV 5 AV 6 AV OUT Les raccordements sont terminés. Passez à la page suivante pour optimiser les réglages des enceintes. UBWOOF R PRE OUT ZO E OU L’unité (arrière) Mettre l’unité sous tension MAIN ZONE PURE D RECT ZONE 2 ZONE CONTROL INFO MEMORY PRE ET INPUT FM AM TUNING VOLUME SCENE BD/DVD PHONES S LENT CINEMA YPAO MIC ONE CONTROL TV NET RAD O V DEO AUX PROGRAM • Lorsque le téléviseur est raccordé à l’unité par un câble HDMI, vous pouvez configurer les réglages de cette dernière à l’aide du menu qui s’affiche sur le téléviseur. Par ailleurs, vous pouvez sélectionner la langue souhaitée dans le menu affiché à l’écran parmi les langues suivantes : anglais (par défaut), japonais, français, allemand, espagnol, russe, italien et chinois. Pour plus d’informations, reportez-vous au « Mode d’emploi ». Des illustrations d’écrans de menus anglais sont utilisées comme exemples dans ce guide. STRAIGHT HDMI/ MHL V 1A VIDEO V 2 1A L’unité (avant) Fr 5 5 Optimisation automatique des réglages d’enceintes (YPAO) 1 Raccordez le microphone YPAO à la prise YPAO MIC sur le panneau avant. L’écran suivant apparaît sur le téléviseur. La fonction Yamaha Parametric room Acoustic Optimizer (YPAO) permet de détecter les raccordements des enceintes et de mesurer la distance entre ces dernières et la position d’écoute. Elle optimise ensuite automatiquement les réglages des enceintes tels que les paramètres d’équilibre du volume et les paramètres acoustiques qui conviennent à la pièce. • Lors de la mesure, des signaux test sont restitués à un volume élevé. Assurez-vous que le signal test n’effraie pas les jeunes enfants. Évitez également d’utiliser cette fonction la nuit, où elle peut constituer une nuisance pour les autres. • Lors de la mesure, vous ne pouvez pas régler le volume. • Faites en sorte que la pièce soit le plus calme possible. • Ne raccordez pas d’écouteurs. • Ne restez pas entre les enceintes et le microphone YPAO pendant la mesure (environ 3 minutes). • Placez-vous dans un coin de la pièce ou quittez-la. Préparation à la fonction YPAO RECE VER SOURCE RECEIVER HDMI 1 2 3 4 5 V AUX AV 1 2 3 5 6 1 4 TUNER USB NET AUDIO MA N 2 • Pour annuler l’opération, débranchez le microphone YPAO avant le début de l’opération de mesure. ZONE 2 2 SCENE BD DV DVD Allumez le caisson de graves et réglez le volume à moitié. Si la fréquence de coupure est réglable, réglez-la sur le maximum. TV NET YPAO MIC PROGRAM MUTE TOP MENU VOLUME Pour commencer la mesure, utilisez les touches de curseur pour sélectionner « Measure » et appuyez sur ENTER. La mesure commence dans les 10 secondes. Lorsque la mesure est terminée, l’écran suivant apparaît sur le moniteur TV. POP UP MENU ON SCREEN VOLUME RADIO L’unité (avant) OPTION CROSSOVER/ HIGH CUT ENTER RETURN DISPLAY Touches de curseur ENTER RETURN BAND MIN MAX MIN MODE MAX TUNING PRESET Microphone YPAO SUR DECODE STRA GHT MOV E MUSIC NFO SLEEP ENHANCER PURE DIRECT 1 2 5 6 9 0 3 4 8 MEMORY Hauteur d’oreille TV MUTE 6 Fr ENT • Si les touches de curseur ne fonctionnent pas, appuyez sur RECEIVER puis utilisez les touches de curseur. NPUT TV VOL Placez le microphone YPAO à votre position d’écoute (à hauteur d’oreilles). Nous conseillons l’utilisation d’un trépied comme support de microphone. Lorsque vous utilisez un trépied, utilisez les vis du trépied pour fixer le microphone. 10 TTVV CH CODE S T • Si un message d’erreur (par exemple E-1) ou d’avertissement (par exemple W-2) apparaît, reportez-vous aux sections « Messages d’erreur » ou « Messages d’avertissement » du « Mode d’emploi ». • Si le message d’avertissement « W-1:Out of Phase » apparaît, reportez-vous à la section « Si le message « W-1:Out of Phase » apparaît » se trouvant à la page suivante. 3 4 Utilisez les touches de curseur pour sélectionner « Save/Cancel » et appuyez sur ENTER. Utilisez les touches de curseur pour sélectionner « SAVE » et appuyez sur ENTER. Si le message « W-1:Out of Phase » apparaît Suivez la procédure ci-dessous pour vérifier les raccordements de l’enceinte. a Utilisez les touches de curseur pour sélectionner « Result » et appuyez sur ENTER. b Utilisez les touches de curseur pour sélectionner « Wiring ». c Vérifiez les raccordements de câble (+ et -) de l’enceinte désignée par « Inversé » dans le message d’avertissement. Si l’enceinte est correctement raccordée : Selon le type d’enceintes ou l’environnement, ce message peut apparaître, même si les enceintes sont correctement raccordées. Dans ce cas, vous pouvez ignorer le message. 5 Appuyez sur RETURN et passez à l’étape 3. Débranchez le microphone YPAO de l’unité. L’optimisation des réglages d’enceintes est maintenant terminée. Si l’enceinte n’est pas correctement raccordée : Mettez l’unité hors tension et raccordez à nouveau le câble d’enceinte, puis essayez à nouveau d’effectuer la mesure YPAO. • Le microphone YPAO est sensible à la chaleur. Ne le placez pas dans un endroit où il pourrait être exposé directement à la lumière du soleil ou à des températures élevées (sur un équipement AV, etc.). Fr 7 6 Lecture d’un disque BD/DVD Voyons maintenant comment lire un disque BD/DVD. sur HDMI 1 pour sélectionner 1 Appuyez « HDMI 1 » comme source d’entrée. Pour sentir les effets d’ambiance sonore produits par l’unité, nous vous recommandons de lire les disques avec le système audio multivoies (5.1 voies et plus). RECEIVER SOURCE HDMI L’unité propose diverses autres fonctions. VOL HDMI1 L SL SW C R SR 2 Commencez la lecture sur le lecteur BD/DVD. 3 Appuyez à plusieurs reprises sur STRAIGHT pour sélectionner « STRAIGHT ». HDMI 1 1 5 V AUX AV 1 2 3 4 5 6 1 TUNER USB NET AUDIO MA N 2 STRAIGHT 4 SCENE TV NET Reportez-vous au « Mode d’emploi » sur le CD-ROM fourni pour savoir comment utiliser l’unité de manière optimale. Raccordement d’autres appareils de lecture VOL ZONE 2 BD DV DVD Encore plus de fonctions ! RADIO L SL SW C R SR Appuyez sur VOLUME pour régler le volume. Raccordez des appareils audio (lecteurs CD et autres), consoles de jeux, caméscopes, etc. Sélection du mode sonore VOL PROGRAM MUTE TOP MENU VOLUME VOLUME OPTION SW C R SR Si le système de son d’ambiance ne fonctionne pas ENTER RETURN L SL La procédure d’installation de base est maintenant terminée. POP UP/MENU ON SCREEN Volume -30.0dB DISPLAY Sélectionnez le programme sonore souhaité (CINEMA DSP) ou le décodeur d’ambiance qui convient aux films, à la musique, aux jeux, aux programmes sportifs, etc. Écoute de musique à partir d’un iPod BAND MODE TUNING PRESET SUR DECOD MOV E MUS C NFO SLEEP 1 2 STRA GHT ENHANCER PURE DIRECT 5 6 9 0 3 Vérifiez le réglage de la sortie audio numérique du lecteur BD/DVD. 4 8 MEMORY 10 STRAIGHT Lors de la lecture à l’aide du système audio multivoies, le son est restitué uniquement par les enceintes avant ENT Il est peut-être réglé pour restituer un son à 2 voies (PCM par exemple). TV Une enceinte spécifique n’émet aucun son NPUT TV VOL MUTE TTVV CH CODE S T Reportez-vous à la section « Guide de dépannage » du « Mode d’emploi ». Grâce au câble USB fourni avec l’iPod, vous pouvez écouter votre musique sur l’unité. n Écoute d’émission FM/AM n Lecture de musique stockée sur un dispositif de stockage USB n Lecture de contenus réseau n Sélection simultanée de la source et des paramètres favoris Pour plus d’informations, reportez-vous à la section « Fonctions de l’unité ». 8 Fr © 2013 Yamaha Corporation Printed in Malaysia ZF58230
This document in other languages
- français: Yamaha RX-A730