Download User's Guide For Label Applicator APN10-30
Transcript
TOWA User's Guide For Label Applicator APN10-30 Thank you for purchasing TOWA Label Applicator. Please read the instructions below before you use the unit. ******* Getting Started ******* 1 Twist the label Holder in a counterclockwise direction and remove it. Set your roll label, and place the Label Holder back by twisting it. 4 Gentry squeeze the Lever, then a label will appear at the nose-section. Release the Lever each time a label is dispensed. 2 Unlock the Bottom Cover by sliding the Tab with "Open" sign, and open the Bottom Cover. Insert the Roll Label under the clear plastic plate which hold the Roll Label. Turn back the Roll Label via the nose section. 5 3 Length of the Roll Label should be longer than the Bottom cover. Place back the Bottom Cover and turn the Tab back until it clicks. Now, the Roll Label is fixed by the Bottom Cover. Now the unit is ready to use. * Do not keep squeezing the lever when you apply a label. ATTENTION! 1. 2. 3. 4. 5. 6. 7. Lever should be squeezed gently. Otherwise, internal part (Gear B) will get broken, and the unit becomes unusable accordingly. Squeeze the Lever fully first and release it right away after the label is ready to apply. This unit is a precision instruments. Avoid high impact like bump or rough squeeze. These can be the cause of failure. Watch out for portion where fingers can be squeezed, or any sharp parts. Keep away from small children. Label with thickness under 50 micrometers are unusable. Film Labels or Synthetic materials may cause a malfunction even the thickness is under 50 micrometers. This unit is a label applicator. Do not use for other purpose. <Label size> * For backing papers, up to 4mm wider than the maximum width listed below is usable. Model Weight APN10-30 Approx. 312g Label Applicator is TOWA's registered Trade Name. Label Size Width 20 - 30 mm Max outside diameter Length 20 - 60 mm 100 mm Product specification may be changed without notice. MADE IN JAPAN TOWA User's Guide For Label Applicator APF Series Thank you for purchasing TOWA Label Applicator. Please read the instructions below before you use the unit. ******* Getting Started ******* 1 Twist the label Holder in a counterclockwise direction and remove it. Set your roll label, and place the Label Holder back by twisting it. 2 4 Unscrew the clincher with sensor a little. Locate the sensor in the center of the label. Screw the clincher with the sensor. 5 Unlock the Bottom Cover by sliding the Tab with "Open" sign, and open the Bottom Cover. Insert the Roll Label under the clear plastic plate which hold the Roll Label. Turn back the Roll Label via the nose section. Gentry squeeze the Lever, then a label will appear at the nose-section. Release the Lever each time a label is dispensed. 3 6 Length of the Roll Label should be longer than the Bottom cover. Place back the Bottom Cover and turn the Tab back until it clicks. Now, the Roll Label is fixed by the Bottom Cover. Now the unit is ready to use. * Do not keep squeezing the lever when you apply a label. SENSOR HERE ↓ ATTENTION! 1. 2. 3. 4. 5. 6. 7. Lever should be squeezed gently. Otherwise, internal part (Gear B) will get broken, and the unit becomes unusable accordingly. Squeeze the Lever fully first and release it right away after the label is ready to apply. This unit is a precision instruments. Avoid high impact like bump or rough squeeze. These can be the cause of failure. Watch out for portion where fingers can be squeezed, or any sharp parts. Keep away from small children. Label with thickness under 50 micrometers are unusable. Film Labels or Synthetic materials may cause a malfunction even the thickness is under 50 micrometers. This unit is a label applicator. Do not use for other purpose. <Label size> * For backing papers, up to 4mm wider than the maximum width listed below is usable. Model Weight APF-30 Label Size Max outside diameter Width Length Approx. 312g 20 - 30 mm 20 - 60 mm 100 mm APF-60 Approx. 370g 20 - 60 mm 20 - 60 mm 100 mm APF-100 Approx. 420g 20 - 100 mm Label Applicator Applicator isis TOWA's TOWA'sregistered registeredTrade TradeName. Name. 20 - 60 mm 100 mm Product specification may be changed without notice. MADE IN JAPAN