Download Matsushita Electric Industrial Co., Ltd., Osaka, Japan 4PW12556
Transcript
CZ-P11~75BK11P 4PW12556-1A.fm Page 1 Friday, September 27, 2002 1:41 PM CZ-P11BK11P CZ-P18BK11P CZ-P37BK11P CZ-P40BK11P CZ-P75BK11P Installation manual Line branch pipes for Urban Multi IMPROPER INSTALLATION OR ATTACHMENT OF EQUIPMENT OR ACCESSORIES COULD RESULT IN ELECTRIC SHOCK, SHORT-CIRCUIT, LEAKS, FIRE OR OTHER DAMAGE TO THE EQUIPMENT. BE SURE ONLY TO USE ACCESSORIES MADE BY PANASONIC WHICH ARE SPECIFICALLY DESIGNED FOR USE WITH THE EQUIPMENT AND HAVE THEM INSTALLED BY A PROFESSIONAL. IF UNSURE OF INSTALLATION PROCEDURES OR USE, ALWAYS CONTACT YOUR INFORMATION. THIS KIT INCLUDES THE FOLLOWING PARTS gas side junction INSTALLATION ■ PANASONIC DEALER FOR ADVICE AND liquid side junction heat insulating material different diameter union 1 set for each junction Only for CZ-P37BK11P PROCEDURE Junction sizes are as follows liquid side junction gas side junction CZ-P11BK11P ø9.5 ø9.5 ø15.9 ø12.7 ø19.1 ø6.4 ø15.9 ø6.4 ø9.5 CZ-P18BK11P ø9.5 ø15.9 ø9.5 ø15.9 ø19.1 ø12.7 ø19.1 ø6.4 ø15.9 ø6.4 ø22.2 ø9.5 CZ-P37BK11P ø15.9 ø12.7 ø12.7 ø15.9 ø31.8 ø9.5 ø28.6 ø12.7 ø19.1 ø15.9 ø25.4 ø12.7 CZ-P40BK11P ø19.1 ø6.4 ø19.1 reducer: ø25.4➞ø19.1 ø28.6➞ø25.4 ø38.1 ø12.7 ø12.7 ø19.1 ø31.8 ø31.8 ø15.9 ø12.7 ø15.9 CZ-P75BK11P ø19.1 ø25.4 ø28.6 ø19.1 ø25.4 ø9.5 ø15.9 reducer: ø15.9➞ø12.7 reducer: ø9.5➞ø6.4 ø22.2 ø15.9 ø25.4 ø9.5 ø15.9 ø12.7 ø19.1 ø12.7 ø44.5 ø31.8 ø38.1 ø31.8 ø15.9 ø19.1 reducer: ø19.1➞ø15.9➞ø12.7 / ø12.7➞ø9.5➞ø6.4 reducer: ø25.4➞ø19.1➞ø15.9 / ø31.8➞ø34.9 (3x) ø38.1➞ø41.3 / ø31.8➞ø34.9➞ø41.3 Matsushita Electric Industrial Co., Ltd., Osaka, Japan Made in Belgium ø38.1 ø25.4 CZ-P11~75BK11P 4PW12556-1A CZ-P11~75BK11P 4PW12556-1A.fm Page 2 Friday, September 27, 2002 1:41 PM Use a pipe cutter to cut off the pipe at a position where the size of the pipe fits the size of the connecting pipe selected according to the pipe selection procedure. Be sure to insulate the junction against heat. ■ Seal the heat insulating material and field piping heat insulating material junction with tape. Example: Model CZ-P11BK11P Diameter 9.5 mm outlet of the liquid piping Use a pipe cutter to cut the piping Heat insulating material (supplied) Junction ø9.5 Cut the center area of the piping ➞ (supplied) Model CZ-P37BK11P NOTE Tape (Field supply) Apply tape to ➀, ➁, ➂ and ➃ Diameter 28.6 mm outlet of gas piping 3 1 2 Use the provided special union for connection Cut the piping (A) with a pipe cutter before connecting 2 1 4 Field piping heat insulating material Part A ø28.6 Outlet for suction gas piping Different diameter union (CZ-P37BK11P) INSTALLATION PRECAUTIONS Install the junction so that it is branched vertically or horizontally. or vertical Within ±30° (horizontal line) View A ➞ Make sure to flow nitrogen gas through the pipe when brazing. CZ-P11~75BK11P Line branch pipes for Urban Multi 4PW12556-1A Installation manual