Download Hampton Bay AL772-BN Use and Care Manual
Transcript
323-627 Baxter II 52 in Ceiling Fan Owner’s Manual Baxter II Ventilador de Techo de 1,32 m Manual del Propietario Baxter II by Hampton Bay ® 52” Baxter II Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Ceiling Fan by Hampton Bay Date Purchased Table of Contents Store Purchased Safety Rules . . . . . . . . . . . . . . . . . . . . 1 Model No. 323-627 Unpacking Your Fan . . . . . . . . . . . . . . 2 Installing Your Fan . . . . . . . . . . . . . . . 3 Serial No. Installing the Light Kit . . . . . . . . . . . 10 Operating Your Fan . . . . . . . . . . . 12 Vendor No. 219032 Care of Your Fan . . . . . . . . . . . . . . . . 13 Troubleshooting . . . . . . . . . . . . . . . . . 13 UPC 792145356011 Specifications . . . . . . . . . . . . . . . . . . 14 Warranty Information . . . . . . . . . . . . 15 Safety Rules - Read and Save These Instructions 1. To reduce the risk of electric shock, insure electricity has been turned off 10. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires should be at the circuit breaker or fuse box before beginning. spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and ungrounded conductor on the 2. All wiring must be in accordance with the National Electrical Code other side of the outlet box. “ANSI/NFPA 70-1999” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician. 11. All set screws must be checked and retightened where necessary before installation. 3. WARNING: To reduce the risk of electrical shock or fire, do not use this fan with any solid-state fan speed control device. It will permanently WARNING damage the electronic circuitry. 4. CAUTION: To reduce the risk of personal injury, use only the screws provided with the outlet box. TO REDUCE THE RISK OF PERSONALL INJURY, DO NOT BEND THE BLADE ARMS (ALSO REFERRED TO AS FLANGES), WHEN INSTALLING THE BRACKETS, BALANCING THE BLADES OR CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS IN– BETWEEN ROTATING FAN BLADES. 5. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 pounds, Use only UL WARNING Listed outlet boxes marked “FOR FAN SUPPORT”. 6. The fan must be mounted with a minimum of 7 feet clearance from the trailing edge of the blades to the floor. 7. Avoid placing objects in the path of the blades. 8. To avoid personal injury or damage to the fan and other items, be cautious when working around or cleaning the fan. 9. Do not use water or detergents when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning. TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR FAN SUPPORT WITH THE SCREWS PROVIDED WITH THE OUTLET BOX. ATTENTION FAN INCLUDES A 190W LIMITER TO COMPLY WITH THE DEPARTMENT OF ENERGY 2009 REGULATION. LAMPING THIS PRODUCT OVER 190W WILL CAUSE THIS FAN TO NOT LIGHT. PLEASE USE BULBS WITH A TOTAL WATTAGE UNDER THE 190W REGULATION. 1 Unpacking Your Fan 2 Unpack your fan and check the contents. You should have the following items: 6 3 1 9 A B 10 4 7 5 C 11 8 12 1. 2. 3. 4. 5. 6. Set of blades (5) Canopy assembly Ball/downrod assembly Coupling cover Fan motor assembly Blade arms (5) WARNING DO NOT INSTALL OR USE FAN IF ANY PART IS DAMAGED OR MISSING. CALL TOLL FREE 1-877-902-5588. 2 7. 8. 9. 10. 11. 12. Mounting plate Light kit assembly Glass shade 40 Watt E12 candelabra bulbs (3) Pull chains and fobs (2) Additional plastic plug A. Blade Attachment Hardware (16 Screws with 16 Fiber Washers) B. Electrical Hardware (3 Plastic Wire Nuts) C. Balance Kit Installing Your Fan Tools Required Provide Strong Support Figures 1~3 are examples of different ways to mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Outlet Box Mounting Options Ceiling Mounting Plate Figure 3 Outlet Box If there isn't an existing UL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Figure 1 Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 35 lbs). Do not use plastic outlet boxes. Note: You may need a longer downrod to maintain proper blade clearance when installing on a steep, sloped ceiling. The maximum angle allowable is 19°. If the canopy touches downrod, remove the decorative canopy bottom cover and turn the canopy 180° before attaching the canopy to the mounting plate. WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, MOUNT FAN ONLY TO AN OULET BOX MARKED ACCEPTABLE FOR FAN SUPPORT AND USE THE MOUNTING SCREWS PROVIDED WITH THE OULET BOX. OUTLET BOX COMMONLY USED FOR THE SUPPORT OF LIGHTING FIXTURE MAY NOT BE ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT. Outlet Box Figure 4 Outlet Box Figure 2 To hang your fan where there is an existing fixture but no ceiling joist, you may need an installation hanger bar as shown in Figure 4 (available at any Home Depot store). 3 Hanging the Fan 5. Align the holes at the bottom of the downrod with the holes in the coupling on top of the motor housing (Figure 6). Carefully insert the REMEMBER to turn off the power. Follow the clevis pin through the holes in the collar and steps below to hang your fan properly. downrod. Be careful not to jam the clevis pin against the wiring inside the downrod. Insert 1. Remove the decorative canopy bottom cover the cotter pin through the hole near the end of from the canopy by turning the cover counter the clevis pin until it snaps into its locked clockwise. (Figure 5) position, as noted in the circle inset of Fig. 6. 2. Remove the mounting bracket from the canopy by removing the 1 of 2 screws from the bottom of the mounting bracket and loosening the other one a half turn from the screw head. Next, turn the canopy counter clockwise to removing the canopy cover form the canopy. (Figure 5) 3. Remove the clevis pin, cotter pin and set screws from the top of the motor assembly. (Figure 6) NOTE: If a longer downrod is needed, take out the screw located in the hanger ball, lower the hanger ball and remove the pin, remove all 3 pieces from the downrod and assemble them onto the new longer downrod before proceeding step 4. (The longer downrod is available at any Home Depot store) 4. Route wires exiting from the top of the fan motor through the coupling cover, canopy cover, canopy and then through the ball/ downrod. (Figure 6) 4 WARNING Motor Wires Ball/Downrod Assembly Ceiling Canopy Canopy Bottom Cover Coupling Cover FAILURE TO PROPERLY INSTALL COTTER PIN AS NOTED IN STEP 5 COULD RESULT IN FAN LOOSENING AND POSSIBLY FALLING. Pin in Locked Positioon Tighten Screw Firmly Motor Collar 6. Tighten two set screws at top of the fan motor collar firmly and evenly. (Fig. 6) Clevis Pin Cotter Pin Ceiling Mounting Bracket Figure 6 Ceiling Canopy Canopy Bottom Cover Figure 5 Installing Fan to the Electrical Box WARNING UL Listed Outlet Box THE TAB IN THE RING MUST REST IN THE GROOVE OF THE HANGER BALL AS FIGURE 8. FAILURE TO PROPERLY SEAT THE TAB IN THE GROOVE COULD CAUSE DAMAGE TO WIRING. WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR OTHER PERSONAL INJURY. MOUNT FAN ONLY TO AN OUTLET BOX OR SUPPORTING SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT AND USE THE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX. 1. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 7. 120V Wires Ceiling Mounting Bracket Tab Mounting Screws (Supplied with Electrical Box) Figure 7 2. Install the ceiling mounting bracket on the outlet box with the screws and washers provided with your outlet box (Figure 7). 3. Security tighten the two mounting screws. 4. Carefully lift the fan assembly up to the ceiling mounting bracket and seat the hanger ball in the mounting bracket socket. Make sure the tab on the mounting bracket socket is properly seated in the groove in the hanger ball (Figure 8). This will help to balance the ceiling fan. Tab Groove Figure 8 5 TO AVOID POSSIBLE ELECTRICAL SHOCK, BE SURE ELECTRICITY IS TURNED OFF AT THE MAIN FUSE BOX BEFORE WIRING. If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps below to connect the fan to your household wiring. Use the wire nuts supplied with your fan. Secure the wire nuts with electrical tape. Make sure there are no loose strands or connections. 1. Connect the ground conductor of the 120V supply (this may be a bare wire or a wire with green colored insulation) to the green ground lead(s) of the fan. (Figure 9) SUPPLY CIRCUIT BLACK WHITE WARNING 5. Turn wire nut connections upward, spreading them apart so the green (ground) will be on one side of the outlet box and the white, black and blue wire will be on the other side, and push carefully up into the outlet box. WARNING CHECK TO SEE THAT ALL CONNECTIONS ARE TIGHT, INCLUDING GROUND, AND THAT NO BARE WIRE IS VISIBLE AT THE WIRE NUTS. EXCEPT FOR THE GROUND WIRE. WARNING ELECTRICAL DIAGRAMS ARE FOR REFERENCE ONLY. OPTIONAL USE OF ANY LIGHT KIT SHALL BE UL LISTED AND MARKED SUITABLE FOR USE WITH THIS FAN. Ground Conductor Outlet Box BLUE BLACK WHITE GREEN Making the Electrical Connections Green Ground Lead Ground to Downrod WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT USE THIS FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE. 2. Connect the fan motor white wire to the supply white (neutral) wire using a wire nut. (Figure 9) 3. Connect the fan motor black wire to the supply black (hot) wire using a wire nut. (Figure 9) 4. Connect the blue wire for light kit to the black household supply wire. 6 Figure 9 Finishing the Fan Installation 1. Tuck connections neatly into ceiling outlet box. 2. Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 10) Outlet Box Ceiling Mounting Bracket Screw 3. Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by tightening the two set screws. Note: Adjust the canopy screws as necessary until the canopy and canopy cover are snug. WARNING MAKE SURE THE TAB ON THE MOUNTING BRACKET PROPERLY SITS IN THE GROOVE IN THE HANGER BALL BEFORE ATTACHING THE CANOPY TO THE BRACKET BY TURNING THE HOUSING UNTIL IT DROPS INTO PLACE. Canopy Screw Canopy Bottom Cover Figure 10 7 Attaching the Fan Blades NOTE MOTOR IS SHIPPED WITH RUBBER PACKING MOUNTS TO PREVENT MOVEMENT DURING TRANSPORTATION. REMOVE 5 RUBBER PACKING MOUNTS FROM FAN MOTOR ASSEMBLY AND DISCARD PRIOR TO ATTACHING BLADE ARMS. (FIG. 11) 1. Attach blades to blade arms using three screws with fiber washers (Fig. 12). Start a screw into the blade arm, do not tighten. Repeat for the 2 remaining screws and washers. 2. Tighten each screw securely starting with the center screw. Make sure the blade is straight. Repeat steps for the remaining blades. Motor Assembly Rubber packing mounts Screws Tab Figure 11 Screws and Fiber Washers Slot Screws 3. Fasten the blade assemblies to the motor by lining up the slots of the blade arms with the tabs on the motor, then tighten the two screws and washers already installed in the blade arms (Fig. 13). Blade Assembly Figure 13 Blade Blade Arm Figure 12 8 WARNING TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE ARMS WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO NO INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES. Attaching the Mounting Plate Blade Balancing The following procedure should correct most fan wobble. Check after each step. Touching Ceiling 1. Remove 1 of 3 screws from the mounting ring and loosen the other 2 screws. (Do not remove) 1. Check that all blade and blade bracket screws are secure. 2. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. Measure from a point on the center of each blade to the point on the ceiling. Measure this distance as shown in Figure 14. Rotate the fan until the next blade is positioned for measurement. Repeat for each blade. Measurements deviation should be within 1/8˝. Run the fan for 10 Minutes. Figure 14 2. Place the key holes on the mounting plate over the 2 screws previously loosened from the mounting ring, turn mounting plate until it locks in place at the narrow section of the key holes. Secure by tightening the 2 screws previously loosened and the one previously removed. (Fig. 15) 3. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable. Mounting Plate Mounting Ring Screws Figure 15 9 Installing the Light Kit CAUTION BEFORE STARTING INSTALLATION, DISCONNECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. 1. Remove 4 screws from the mounting plate. NOTE LIGHT BULBS HAVE NO WARRANTY; CAN BE PURCHASED AT ANY HOME DEPOT STORE. 7. Restore power and your light kit is ready for operation. NOTE MAKE SURE TO LEAVE ENOUGH SPACE BETWEEN THE FAN PULL CHAIN AND THE BULBS SO THE CHAIN DOESN'T RUB AGAINST ANY OF THE BULBS. 2. While holding the light kit assembly under your fan, snap together the wire connection plugs. 3. Secure the light kit assembly to the mounting plate with the 4 screws previously removed. (Fig. 16) Light Kit Assembly 4. Install 3 x 40W candelabra bulbs (included). 5. Remove the decorative nut, glass cap and plastic nut from the light kit stem. Raise the glass shade up against the mounting plate and secure it with the plastic nut. Do not overtighten. Place the glass cap over the light kit stem and secure it with the decorative nut. (Fig. 17) 6. Insert the 2 pull chain through the eyelet in the shade and cap. Secure the glass cap and decorative nut provided (Fig. 17). 10 Bulbs Mounting Plate Wire Connectors Screws Light Kit Assembly Glass Shade Plastic Nut Glass Cap Decorative Nut Pull Chains Figure 17 Figure 16 Fan without Light Kit Wire Connectors (Optional) Nut Washer CAUTION BEFORE STARTING INSTALLATION, DISCONNECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. 1. Disassemble the switch housing from the light kit, you can keep the light kit for future use. (Fig. 18) Switch Housing Light Kit Mounting Plate 2. Attach the additional plastic plug to the switch housing. (Fig. 19) 3. Holding the switch housing under your fan, snap together the wire connection plugs. (Fig. 19) Wire Connectors Screws Figure 18 Switch Housing Plastic Plug Figure 19 4. Install the switch housing to the mounting plate with screws provided. (Fig. 19) 11 Operating Your Fan NOTE WAIT FOR FAN TO STOP BEFORE REVERSING THE DIRECTION OF THE BLADE ROTATION. Turn on the power and check the operation of your fan. There are two pull chains available in your fan: Warm weather - (Counter-Clockwise direction) A downward air flow creates a cooling effect as shown in Figure 20. This allows you to set your air conditioner on a higher setting without affecting your comfort. 1. 3-speed pull chain- it controls the fan speed as follows: 1 pull- High, 2 pulls- Medium, 3 pullsLow, and 4 pulls- Off. Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans, and so on. 2. Light kit pull chain- it controls the light kit in "ON" or "OFF". The reverse switch is located on the surface of the switch housing. Slide the switch to the left for warm weather operation. Slide the switch to the right for cool weather operation. Figure 20 Cool weather - (Clockwise direction) An upward air flow moves warm air off the ceiling are as shown in Figure 21. This allows you to set your heating unit on a lower setting without affecting your comfort. Figure 21 12 Care of Your Fan Troubleshooting Here are some suggestions to help you maintain your fan. 1. Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from ceiling.) PROBLEM SOLUTION Fan will not start 1. Check main and branch circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. Fan sounds noisy 1. Make sure all motor housing screws are snug. 2. Make sure the screws that attach the fan blade bracket to the motor hub is tight. 3. Make sure wire nut connections are not rattling against each other or the interior wall of the switch housing. 4. Allow a 24-hour "breaking-in" period. Most noises associated with a new fan disappear during this time. 5. If using ceiling fan light kit, make sure the screws securing the glassware are tight. Check that the light bulb is also secure. 6. Make sure there is a short distance from the ceiling to the canopy. It should not touch the ceiling. 7. Make sure your ceiling box is secure and rubber isolator pads are used between mounting bracket and outlet box. Lights shut off and will not come back on. 1. This unit is equipped with a wattage limiting device. Lamping in excess of 190 watts will disable your ceiling fan's light kit. To reset your light kit you must turn the power off and relamp, keeping the wattage under 190 watts. Restore power to your ceiling fan and continue normal operation. 2. Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing. Do not use water when cleaning. This could damage the motor, or the wood, or possibly cause an electrical shock. 3. You can apply a light coat of furniture polish to the wood blades for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish. 4. There is no need to oil your fan. The motor has permanently lubricated sealed ball bearings. WARNING MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPY ANY REPAIRS. REFER TO THE SECTION, “MAKING ELECTRICAL CONNECTIONS”. 13 Specifications FAN SIZE SPEED VOLTS AMPS LOW 52” MED. HIGH 120 WATTS RPM CFM 0.21 10 54 1602 0.37 29 100 3125 0.52 62 147 4686 These are approximate measures. They do not include Amps and Wattage used by the light kit. 14 N.W. G.W. C.F. 9.23 kgs (20.31 lbs) 10.3 kgs (22.66 lbs) 2.06' Hampton Bay Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser. Hampton Bay also warrants that all other fan parts, excluding any glass or acrylic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser. We agree to correct such defects without charge or at our option replace with a comparable or superior model if the product is returned to Hampton Bay. To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and reinstalling the product are your responsibility. Damage to any part such as by accident or misuse or improper installation or by affixing any accessories, is not covered by this warranty. Because of varying climatic conditions this warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or peeling. Brass finishes of this type give their longest useful life when protected from varying weather conditions. A certain amount of “wobble” is normal and should not be considered a defect. Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. Hampton Bay hereby disclaims any and all warranties, including but not limited to. Those of merchantability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. The Hampton Bay shall not be liable for incidental, consequential, or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer. IMPORTANT NOTE: To ensure warranty service if ever needed, please register your fan at: www.tal-usa.com/registration You must present a copy of the original purchase receipt to obtain warranty service. Ceiling Fan Parts & Service Department 2919 E. Philadelphia Street Ontario, CA 91761 U.S.A. Attach receipt here for easy location 15