Download Sony WX-4500X Installation Instructions
Transcript
2 A Changer Control Audio Master SUBWOOFER OUT (MONO) Installation/Connections B BUS AUDIO IN BUS CONTROL IN BUS AUDIO IN Source selector* * * WX-4500X Sony Corporation © 2001 Printed in Japan BUS CONTROL IN * not supplied 1 3 To AMP REMOTE IN of an optional power 1 2 ×6 Cautions 3 • This unit is designed for negative ground 12 V DC operation only. • Do not get the wires under a screw, or caught in moving parts (e.g. seat railing). • Before making connections, turn the car ignition off to avoid short circuits. • Connect the yellow and red power input leads only after all other leads have been connected. • Run all ground wires to a common ground point. • Be sure to insulate any loose unconnected wires with electrical tape for safety. • The use of optical instruments with this product will increase eye hazard. ×6 4 For NISSAN cars only Notes on the power supply cord (yellow) • When connecting this unit in combination with other stereo components, the connected car circuit’s rating must be higher than the sum of each component’s fuse. • When no car circuits are rated high enough, connect the unit directly to the battery. Equipment used in illustrations (not supplied) Front speaker Parts Iist (1) Power amplifier The numbers in the list are keyed to those in the instructions. Rear speaker Active subwoofer Connection example (2) CD/MD changer Tip (2-B- ) For connecting two or more changers, the source selector XA-C30 (optional) is necessary. Connection diagram (3) Rotary commander RM-X4S When insert the each connector, be sure to insert it securely, as vibration through driving may cause a poor connection. 1 To a metal surface of the car 2 *I-3-229-007-11* (1) First connect the black ground lead, then connect the yellow and red power input leads. To the power antenna control lead or power supply lead of antenna booster amplifier Notes • It is not necessary to connect this lead if there is no power antenna or antenna booster, or with a manually-operated telescopic antenna. • When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.” 4 5 6 7 amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. To the interface cable of a car telephone To a car’s illumination feed Be sure to connect the black ground lead to it first. To the +12 V power terminal which is energized in the accessory position of the ignition key switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energised at all times. Be sure to connect the black ground lead to it first. • When your car has a built-in FM/AM antenna in the rear/side glass, see “Notes on the control and power supply leads.” To the +12 V power terminal which is energised at all times Be sure to connect the black ground lead to it first. Notes on the control and power supply leads • The power antenna control lead (blue) supplies +12 V DC when you turn on the tuner. • When your car has built-in FM/AM antenna in the rear/side glass, connect the power antenna control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna booster. For details, consult your dealer. • A power antenna without relay box cannot be used with this unit. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition key is turned off. Notes on speaker connection • Before connecting the speakers, turn the unit off. • Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. • Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. • Do not connect the ground lead of this unit to the negative (–) terminal of the speaker. • Do not attempt to connect the speakers in parallel. • Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. • To avoid a malfunction, do not use the built-in speaker wires installed in your car if the unit shares a common negative (–) lead for the right and left speakers. • Do not connect the unit’s speaker cords to each other. 3 Source selector*1 *1 *1 Supplied with XA-C30 BUS CONTROL IN SUBWOOFER OUT (MONO) BUS AUDIO IN Supplied with the CD/MD changer REMOTE IN MONO MONO *1 *2 L R SUB WOOFER OUT BUS AUDIO IN *1 *2 RCA pin cord (not supplied) * 2 *1 *2 Fuse (10 A) 4 Black Blue ANT REM 1 Max. supply current 0.1 A 2 Blue/white striped White AMP REM Left Max. supply current 0.3 A White/black striped 3 Light blue ATT Gray 4 Right Gray/black striped Orange/white striped ILLUMINATION 5 Green Red Left Green/black striped Purple 6 Yellow Right 7 Purple/black striped 3 • • 3 4 5 • 6 • • 4 5 • • • • • • 6 • • 7 • • • 7 • • • 1 • • • • • • 1 2 2 2 • 2 3 • • 1 • 2 3 • • • • • 1 2 • • • • • • • • • • • not supplied Connect the Bus cable to its terminal with the unit’s V mark and the Bus cable’s v mark aligned. 4 A B TOYOTA/MITSUBISHI NISSAN This illustration is for TOYOTA cars. Bracke 1 or 2 1 or 2 max. size 5 × 8 mm (7/32 × 11/32 in.) 1 max. size 5 × 8 mm (7/32 × 11/32 in.) to dashboard/center console 2 1 2 Bracket 3 1 or 2 Existing parts supplied with your car max. size 5 × 8 mm (7/32 × 11/32 in.) 1 Existing parts 2 Bracket Precautions •Choose the installation location carefully so that the unit will not interfere with normal driving operations. •Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperatures, such as in direct sunlight or near heater ducts. •Use only the supplied mounting hardware for a safe and secure installation. When mounting this unit to the preinstalled brackets of your car, use the supplied screws 1 or 2 in the appropriate screw holes, according to your vehicle: T for TOYOTA, M for MITSUBISHI, and N for NISSAN. 1 2 • • T N M M T N M T T • N T M N T T N T N N T T Mounting angle adjustment N N M N M Adjust the mounting angle to less than 20°. Frequency select switch The AM (FM) tuning interval is factory-set to the 9 k (50 k) position. If the frequency allocation system of your country is based on 10 kHz (200 kHz) interval, set the switch on the left side of the unit to the 10 k (200 k) position before making connections. After the frequency select switch is set, you must press the reset button to reset the unit. T N M M T N T T N N T N • Notes • Use the screws 1 or 2 depending on the make of car. When this unit is attached to a MITSUBISHI car, use the supplied screws 2. • To prevent malfunction, be sure to install using brackets and the supplied screws 1 or 2. • Do not apply excessive force to the buttons of the unit. • Do not push on the display window. • Before mounting, make sure there is nothing on the top of the unit. 1 2 2 • 1 2 • • • T N M M T N T T Warning when installing in a car without ACC (accessory) position on the ignition key switch N N T N M (OFF) (OFF) M Be sure to press (OFF) on the unit for two seconds to turn off the clock display after turning off the engine. When you press (OFF) only momentarily, the clock display does not turn off and this causes battery wear. CD To set the frequency select switch, use a pointed object, such as a ball-point pen, to gently slide the switch. DSO Reset button Mounting the unit in a Japanese car (4) CD DSO EQ7 DSPL SCRL OFF SOUND MENU MD ATT SA SEEK/AMS DSPL SCRL OFF When the installation and connections are completed, be sure to press the reset button with a ball-point pen, etc. You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer. EQ7 SEEK/AMS MODE SOURCE Reset button Note When you connect the power supply cord to the unit or reset the unit, wait for about 10 seconds before you insert a disc. If you insert a disc within these 10 seconds, the unit will not be reset, and you will have to press the reset button again. 4 SEEK/AMS SOUND MENU MD ATT SA SEEK/AMS MODE SOURCE B NISSAN Bracket 1 or 2 max. size 5 × 8 mm (7/32 × 11/32 in.) rd/center console 1 to dashboard/center console 2 3 1 or 2 1 or 2 max. size 5 × 8 mm (7/32 × 11/32 in.) 1 max. size 5 × 8 mm (7/32 × 11/32 in.) Existing parts supplied with your car 2 1 Bracket 2 Bracket 1 2 T N • • T N M M M T N T M T • • • • T N T N N T N N M T N T N M • 1 • • • • • 2 2 • 1 T N 2 M • • • M T N T T N N T N M T N M M T N T T N N T N M (OFF) (OFF) CD DSO EQ7 DSPL SCRL OFF SEEK/AMS SOUND 4 CD DSO EQ7 DSPL SCRL OFF 4 SEEK/AMS SOUND MENU MD ATT SA SEEK/AMS MODE SOURCE MENU MD ATT SA SEEK/AMS MODE SOURCE ket to dashboard/center console 3 1 or 2 max. size 5 × 8 mm (7/32 × 11/32 in.) s supplied with your car 1 2 Bracket T N • • • M M T N T T N N T N M • • • • • T N M M T N T T N N T N M CD DSO EQ7 DSPL SCRL OFF SEEK/AMS SOUND 4 MENU MD ATT SA SEEK/AMS MODE SOURCE