Download SECO-LARM USA SECO-LARM EV-122C-DXB3Q User's Manual

SECO-LARM BALL-MOUNT IR DOME CAMERA Manual
SECO-LARM
TROUBLE SHOOTING
The screen is blank
• Check that the camera is powered up.
• Check that the monitor is powered up.
• Check that the video cable connecting the camera to the monitor is connected properly.
The screen image is dim
• Clean the lens (using a soft, clean cloth).
• Check that the light source is adequate.
The screen image has poor contrast
• Adjust the monitor’s contrast knob.
• Change the position of the camera.
The screen image flickers
• Change the position of the camera.
The screen image is distorted
• Change the position of the camera.
The camera case is hot
• Check that the correct power supply is in use.
EV-122C-DXB3Q
Multi-Axis Ball-Mount Color Dome Camera
MANUAL
IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held
responsible for the use of this product in violation of any current laws or statutes.
WARNING Stop using the camera if you see a malfunction like smoke or unusual heat, as it could cause fire or
electric shock. Do not open the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT Information to the user: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited
to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that
such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal
or property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
• Multi-Axis ball mount for
•
•
wall or ceiling mounting
360° Rotation, 10°~120° tilt
1/3” Sony Super HAD II CCD
•
•
•
•
3.6mm Lens
24 IR LEDs
50ft (15m) IR range
Concealed wiring
C M U.S.A.,
., IInc..
SECO-LARM
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: [email protected]
®
PICSN4
MiEV-122C-DXB3Q_0914b.pmd
Note: Products with model number that ends with "Q" or have a round green "Q" sticker represents RoHS compliant products.
SECO-LARM BALL-MOUNT IR DOME CAMERA Manual
Specifications
EV-122C-DXB3Q (NTSC)
____________________________________________________________________________________________________
Type
Color camera
____________________________________________________________________________________________________
_____Chip
____________________________________________________________________________________________________________________1/3”
________Sony
_________Super
__________HAD
________II___CCD
____________________________________________________________
Resolution
420
TV
lines
____________________________________________________________________________________________________
Pickup elements
510x492 pixels
____________________________________________________________________________________________________
Scanning system
2:1 interlace, V: 60Hz, H: 15.734KHz
____________________________________________________________________________________________________
SECO-LARM BALL-MOUNT IR DOME CAMERA Manual
Parts List
CA-161T - DC plug included.
1 x Camera Ball
1 x Case (2-part construction)
1 x Base
3 x Screws
1 x Manual
1 x DC plug with terminal block
To BNC
(From DC
Camera)
(CA-161T)
Sync
Internal
____________________________________________________________________________________________________
Video
output
1.0Vp~p
composite
output, 75 ohms
____________________________________________________________________________________________________
Power
Connector
3x
Screws
Lens
F1 2, 3.6 mm (lens included)
____________________________________________________________________________________________________
IR LEDs
24
____________________________________________________________________________________________________
IR distance
Up to 50 ft. (15 m)
____________________________________________________________________________________________________
o
o
IR
view
angle
~80
Beam spread, 30o per LED
50
____________________________________________________________________________________________________
Minimum illumination
0 05 lux, (0 lux with IR on)
____________________________________________________________________________________________________
Gamma correction
0.45
____________________________________________________________________________________________________
S/N ratio
>50dB
____________________________________________________________________________________________________
Shutter
control
Auto
Electronic
Shutter
(AES)
1/60~1/100,000 sec. (NTSC)
____________________________________________________________________________________________________
Automatic gain control
Auto
____________________________________________________________________________________________________
White balance
Auto, 2500o~9500o K
____________________________________________________________________________________________________
____Power
_______________source
_____________________________________________________________________________________________________12
_____VDC
_______±10%
____________________________________________________________________
Power
consumption
70
mA
LEDs
off, 200 mA LEDs on
____________________________________________________________________________________________________
Storage temperature
-4°~122° F (-20°~50° C)
____________________________________________________________________________________________________
Operating temperature
14°~122° F (-10°~50° C)
____________________________________________________________________________________________________
Dimensions
311/16” x 211/16” (93 x 69 mm)
____________________________________________________________________________________________________
Weight
6 oz. (170 g)
____________________________________________________________________________________________________
Dimensions:
211/16”
(69mm)
311/16” (93mm)
BNC
Connector
Case
Camera
Ball
Case
BEFORE STARTING
1. Please read this manual carefully and keep it for future reference.
2. Use the camera within given temperature and electrical limits.
3. Do not mount the camera where it is exposed to rain or other
moisture, or in humid or dusty places.
4. Do not point the camera at the sun. Heat could damage the
camera, even when not in use.
5. Do not mount the camera in areas exposed to radiation, strong
magnetic fields, or strong electrical signals.*
INSTALLATION
1. Run a 12VDC power supply wire and a video cable with a male
BNC connector through the wall to where the camera is to be
mounted.
2. Temporarily connect the camera to the 12VDC power supply.
3. Temporarily connect the camera’s female BNC connector to the
video cable’s male BNC connector.
4. While watching the monitor, hold the camera against the wall by
hand where it is to be mounted, then turn the camera until it is
certain that this mounting location is correct. Use a pencil to
mark the location of the three screw holes in the base.
5. Disconnect the 12VDC power supply and video cable.
Base
6. Do not open or disassemble the camera. There are no userserviceable parts inside.
7. Do not drop the camera or subject it to strong vibrations.
* Note: Many video monitors produce strong electromagnetic
fields close to the display CRT, especially when the monitor is
turned on or during de-Gaussing, which occurs automatically
with many monitors when the monitor is turned on.
6. Mount the bracket to the wall using the three included mounting
screws. If the wall is made of dry wall, brick, or similar material,
it may be necessary to use screw anchors (not included).
7. Reconnect the 12VDC power supply and video cable. Turn the
monitor on, and make sure the camera is sending the proper
video signal.
8. Adjust the camera angle.
9. Put the case over the camera ball and twist to secure to the
base.
10. Do a final test of the video camera and monitor.
* Note: The base also allows flush-mounting of the camera.
However, for the best security, run the wires through the wall.