Download Pioneer XV-DV363 User's Manual
Transcript
cover & anki.fm 1 ページ 2007年2月3日 土曜日 午後3時18分 cover & anki.fm 2 ページ 2007年2月3日 土曜日 午後3時18分 Thank you for buying this Pioneer product. Please read through these operating instructions so that you will know how to operate your model properly. After you have finished reading the instructions, put them in a safe place for future reference. Location: bottom of the unit IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D3-4-2-1-1_En-A WARNING VENTILATION CAUTION This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain D3-4-2-1-3_A_En or moisture. When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side). WARNING Before plugging in for the first time, read the following section carefully. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230 V D3-4-2-1-4_A_En or 120 V) written on the rear panel. WARNING To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the D3-4-2-1-7a_A_En equipment. WARNING Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the D3-4-2-1-7b_A_En equipment on thick carpet or a bed. CAUTION The STANDBY/ON switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation). D3-4-2-2-2a_A_En cover & anki.fm 3 ページ 2007年2月3日 土曜日 午後3時18分 CAUTION This product is a class 1 laser product, but this product contains a laser diode higher than Class 1. To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel. The following caution label appears on your unit. Location: top of the unit CLASS 1 LASER PRODUCT D3-4-2-1-8_B_En POWER-CORD CAUTION Operating Environment Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement. S002_En Operating environment temperature and humidity: +5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or D3-4-2-1-7c_A_En strong artificial light) This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a restaurant or use in a car or ship) and which requires repair will be charged for even during the K041_En warranty period. If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. Make sure it is properly disposed of after removal. The equipment should be disconnected by removing the mains plug from the wall socket when left unused for a long period of time (for example, when D3-4-2-2-1a_A_En on vacation). HTZ363DVD_WL 4 ページ 2007年2月3日 土曜日 午後3時27分 Contents 01 Controls and displays 04 Disc playback features Front panel . . . . . . . . . . . . . . . . . . . . . . . . .6 Remote control . . . . . . . . . . . . . . . . . . . . . .7 Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Scanning discs . . . . . . . . . . . . . . . . . . . . . 18 Playing in slow motion . . . . . . . . . . . . . . . 18 Frame advance/frame reverse . . . . . . . . . . 18 Playing a JPEG slideshow . . . . . . . . . . . . . 18 Browsing DVD or Video CD/Super VCD discs with the Disc Navigator . . . . . . . . . . . . . . . 19 Browsing WMA, MP3, MPEG-4 AAC, DivX video and JPEG files with the Disc Navigator . . . . . . . . . . . . . . . . . . . . . . . . . 20 Using Playlists . . . . . . . . . . . . . . . . . . . . . 20 Programming playlists . . . . . . . . . . . . . . 20 Listening to playlists . . . . . . . . . . . . . . . . 21 Clearing files from a playlist . . . . . . . . . . 21 Looping a section of a disc . . . . . . . . . . . . 21 Using repeat play . . . . . . . . . . . . . . . . . . . 21 Using random play . . . . . . . . . . . . . . . . . . 21 Creating a program list . . . . . . . . . . . . . . . 22 Other functions available from the program menu . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Searching a disc . . . . . . . . . . . . . . . . . . . . 23 Switching subtitles . . . . . . . . . . . . . . . . . . 23 Switching language/audio channels . . . . . 23 Zooming the screen . . . . . . . . . . . . . . . . . 23 Switching camera angles . . . . . . . . . . . . . 24 Displaying disc information. . . . . . . . . . . . 24 02 Getting started Home theater sound setup . . . . . . . . . . . .10 Using the Auto MCACC setup for optimal surround sound . . . . . . . . . . . . . . . . . . . . .10 Using the on-screen displays . . . . . . . . . . .11 Playing discs . . . . . . . . . . . . . . . . . . . . . . .12 Basic playback controls . . . . . . . . . . . . .12 Resume and Last Memory. . . . . . . . . . . .13 DVD-Video disc menus . . . . . . . . . . . . . .13 Video CD/Super VCD PBC menus . . . . . .13 Listening to the radio . . . . . . . . . . . . . . . . .13 Improving poor FM reception . . . . . . . . .14 Reducing AM reception noise . . . . . . . . .14 Memorizing stations . . . . . . . . . . . . . . . .14 Listening to station presets . . . . . . . . . . .14 Listening to other sources . . . . . . . . . . . . .14 03 Listening to your system Auto listening mode . . . . . . . . . . . . . . . . .15 Listening in surround sound . . . . . . . . . . .15 Dolby Pro Logic II Music settings . . . . . .15 Using Front Stage Surround Advance . . . .16 Using Advanced Surround. . . . . . . . . . . . .16 Listening in stereo . . . . . . . . . . . . . . . . . . .16 Listening with headphones . . . . . . . . . . . .16 Listening with Acoustic Calibration EQ . . .16 Using the Sound Retriever . . . . . . . . . . . . .17 Enhancing dialog. . . . . . . . . . . . . . . . . . . .17 Using the Tone controls . . . . . . . . . . . . . . .17 Adjusting the bass and treble . . . . . . . . .17 Quiet and Midnight modes . . . . . . . . . . .17 Boosting the bass level . . . . . . . . . . . . . . .17 05 USB playback Using the USB interface . . . . . . . . . . . . . . 25 Basic playback controls . . . . . . . . . . . . . . 25 Scanning files . . . . . . . . . . . . . . . . . . . . . . 26 Playing a JPEG slideshow . . . . . . . . . . . . . 26 Browsing files with the Navigator . . . . . . . 26 06 Surround sound settings Using the Setup menu . . . . . . . . . . . . . . . 27 07 Video Adjust menu Video Adjust menu . . . . . . . . . . . . . . . . . . 28 4 En HTZ363DVD_WL 5 ページ 2007年2月3日 土曜日 午後3時28分 08 Initial Settings menu 10 Additional information 29 29 30 30 31 31 32 09 Other connections 33 33 33 34 36 37 37 Italiano 36 Français 34 34 35 35 35 35 Deutsch Connecting external antennas . . . . . . . . . Connecting auxiliary audio components . Recording mode . . . . . . . . . . . . . . . . . . Connecting the S-video output . . . . . . . . . Connecting using the component video output . . . . . . . . . . . . . . . . . . . . . . . . . . . About progressive scan video . . . . . . . . Connecting using HDMI . . . . . . . . . . . . . Switching the HDMI audio setting . . . . . Resetting the HDMI connection. . . . . . . About HDMI . . . . . . . . . . . . . . . . . . . . . . . Using this unit with a Pioneer plasma television . . . . . . . . . . . . . . . . . . . . . . . . . SR+ Setup for Pioneer plasma televisions . . . . . . . . . . . . . . . . . . . . . . . Switching on the SR+ mode . . . . . . . . . About control out connections . . . . . . . . . Nederlands Optional system settings . . . . . . . . . . . . . . 38 Setting the sleep timer . . . . . . . . . . . . . . . 39 Dimming the display . . . . . . . . . . . . . . . . . 39 Disc/content format playback compatibility . . . . . . . . . . . . . . . . . . . . . . . 39 Disc compatibility table. . . . . . . . . . . . . . 40 About DVD+R/DVD+RW compatibility . . . . . . . . . . . . . . . . . . . . . . 40 About DivX . . . . . . . . . . . . . . . . . . . . . . . 41 About MPEG-4 AAC. . . . . . . . . . . . . . . . . 41 About WMA . . . . . . . . . . . . . . . . . . . . . . 41 Using and taking care of discs . . . . . . . . . 42 DVD Video regions . . . . . . . . . . . . . . . . . 42 Installation and maintenance . . . . . . . . . . 42 Hints on installation . . . . . . . . . . . . . . . . 42 Cleaning the pickup lens. . . . . . . . . . . . . 43 Problems with condensation. . . . . . . . . . 43 Moving the system unit . . . . . . . . . . . . . . 43 Screen sizes and disc formats . . . . . . . . . . 43 Troubleshooting. . . . . . . . . . . . . . . . . . . . . 44 General . . . . . . . . . . . . . . . . . . . . . . . . . . 44 DVD/CD/Video CD player . . . . . . . . . . . . 45 Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 USB connection . . . . . . . . . . . . . . . . . . . 46 HDMI connection . . . . . . . . . . . . . . . . . . 46 Error Messages . . . . . . . . . . . . . . . . . . . . 47 Resetting the system . . . . . . . . . . . . . . . . . 48 Using the language code list . . . . . . . . . . . 48 Language code list . . . . . . . . . . . . . . . . . . 49 Country/Area code list . . . . . . . . . . . . . . . . 49 Specifications . . . . . . . . . . . . . . . . . . . . . . 50 English Using the Initial Settings menu . . . . . . . . Video Output settings. . . . . . . . . . . . . . . . Language settings . . . . . . . . . . . . . . . . . . Display settings . . . . . . . . . . . . . . . . . . . . Options settings. . . . . . . . . . . . . . . . . . . . Parental Lock. . . . . . . . . . . . . . . . . . . . . About DivX® VOD content. . . . . . . . . . . Español 5 En HTZ363DVD_EN_WL.book 01 6 ページ 2007年2月3日 土曜日 午後3時13分 Controls and displays Chapter 1 Controls and displays 7 Front panel OPEN/CLOSE 3 8 USB interface Connect a USB device for playback (see USB playback on page 25). DVD/CD 4 USB 5 VOLUME 6 9 PHONES jack Connect headphones. 7 10 Indicator Lights blue when the power is on (except when the dimmer/sleep timer is active). STANDBY/ON PLAY LIST 1 1 VOLUME +/– buttons PLAY LIST 2 PLAY LIST 3 2 11 Remote Sensor 12 Display See Display below. 10 8 11 12 9 1 STANDBY/ON Switches the system on or into standby. 2 PLAY LIST buttons Add tracks (during playback), or select a playlist (while stopped) (page 20). 3 OPEN/CLOSE Opens/closes the disc tray. 4 DVD/CD Selects the DVD/CD function and starts/ pauses/resumes playback. 5 Stops playback. 6 USB Selects the USB function and starts/pauses playback. 6 En HTZ363DVD_EN_WL.book 7 ページ 2007年2月3日 土曜日 午後3時13分 Controls and displays 01 STANDBY /ON DVD/CD TUNER SOUND (FM/AM) RETRIEVER USB LINE OPEN/CLOSE 11 12 SHIFT+ZOOM Changes the screen zoom level (page 23). PLAYLIST 1 3 4 7 2 3 AUDIO SUBTITLE 5 6 ANGLE ZOOM 8 9 1 2 4 TOP MENU – Displays the top menu of a DVD disc in the play position — this may be the same as pressing MENU (page 13). 14 SHIFT+SETUP – Use to make various system and surround sound settings (page 14, 27 and 39). 3 DISPLAY CLEAR 0 TOP MENU 4 5 MENU TUNE SR SETUP ENTER ST HOME MENU ST RETURN 15 6 TUNE MCACC F.S.SURR SURROUND TEST TONE ADVANCED 5 SOUND 8 TV CONTROL 9 INPUT 10 VOLUME MUTE ENTER – Selects an option or executes a command. 16 TUNE +/– – Tunes the radio. 17 ST +/– – Selects station presets when listening to the radio. VOLUME 18 6 3 Number buttons, CLEAR, DISPLAY and DVD controls 7 Sound controls F.S.SURR – Selects Front Stage Surround Advance mode (page 16). Español SHIFT+MCACC – Starts the Auto MCACC setup (page 10). 1 STANDBY/ON Switches the system on or into standby. 2 Function select buttons Selects the source you want to listen to (DVD/ CD, TUNER, USB, LINE). HOME MENU – Displays (or exits) the onscreen menu for Initial Settings, Play Mode functions, etc. Nederlands SHIFT CHANNEL SLEEP Cursor, ENTER and tuning buttons /// – Use the cursor buttons to navigate on-screen displays and menus. Italiano 7 Français 13 Deutsch 1 2 SHIFT+ANGLE Changes camera angle during DVD multiangle scene playback (page 24). English SHIFT+SUBTITLE Displays/changes the subtitles (page 23). Remote control SURROUND – Selects a Surround mode (page 15) or switches to stereo playback (page 16). CLEAR Clears an entry. ADVANCED – Selects a Pioneer original surround mode (page 16) . DISPLAY Displays/changes disc information shown on-screen (page 24). SOUND – Accesses the sound menu to adjust the tone, bass and treble, etc. (page 15 to 17 and 33). SHIFT+AUDIO Selects audio channel/language (page 23). 7 En HTZ363DVD_EN_WL.book 01 8 ページ 2007年2月3日 土曜日 午後3時13分 Controls and displays 8 Playback controls See Basic playback controls on page 12, Disc playback features on page 18 and USB playback on page 25 for an explanation of these controls. 9 TV CONTROL buttons These control Pioneer plasma televisions. 10 SHIFT Press to access the controls highlighted in green. 11 SOUND RETRIEVER – Press to restore CD quality sound to compressed audio sources (page 17). 12 OPEN/CLOSE Opens/closes the disc tray. 13 PLAYLIST buttons Add tracks (during playback), or select a playlist (while stopped) (page 20). 14 MENU – Press to display a USB menu, or the Navigator (page 13, 18 and 26). SHIFT+SR+ – Switches the SR+ mode on/ off (page 36). 15 RETURN – Returns to a previous menu screen. SHIFT+TEST TONE – Outputs the test tone (for speaker setup) (page 27). 16 SLEEP Press to set the sleep timer (page 39). 17 MUTE Mutes the sound (press again to cancel). 18 VOLUME +/– Adjusts the volume. 8 En HTZ363DVD_EN_WL.book 9 ページ 2007年2月3日 土曜日 午後3時13分 Controls and displays 01 1 2 3 4 11 2 PRGSVE Lights when progressive scan video output is selected (page 29). 8 9 RDM Lights during random play (page 21). 10 kHz/MHz Indicates the frequency unit shown in the character display (kHz for AM, MHz for FM). 11 Character display 4 13 Lights during playback. F.SURR. Lights when one of the Front Stage Surround Advance mode is selected (page 16). 15 2 D Lights during playback of a Dolby Digital source (page 15). Español 5 RPT and RPT-1 RPT lights during repeat play. RPT-1 lights during repeat one-track play (page 21). 14 2 PL II Lights during Dolby Pro Logic II decoding (page 15). Nederlands 12 Lights when sleep timer is active (page 39). Italiano 3 SOUND Lights when the Sound Retriever is active (page 17). SURR. Lights when one of the Advanced surround listening modes is selected (page 16). Français 1 DTS Lights during playback of a DTS source (page 15). 10 9 Deutsch REC MODE RPT -1 kHz PGM MHz RDM 2D 2PL 15 14 13 12 6 7 5 PRGSVE SOUND DTS F.SURR. English Display 6 REC MODE Lights when Recording mode is on (page 33). 7 PGM Lights during program play (page 20 and 22). 8 Tuner indicators – Lights when a broadcast is being received. – Lights when a stereo FM broadcast is being received in auto stereo mode. – Lights when FM mono reception is selected. 9 En HTZ363DVD_EN_WL.book 02 10 ページ 2007年2月3日 土曜日 午後3時13分 Getting started Chapter 2 Getting started Home theater sound setup Place your speakers as shown below for optimal surround sound (see the Speaker Setup Guide for more placement tips). • Standard surround setup – This is a standard multichannel surround sound speaker setup for optimal 5.1 channel home theater sound. Front left Center Front right For HTZ565DVD and HTZ767DVD: Center Front left Surround left Subwoofer Surround right Front right Listening position After placing your speakers, see Using the Auto MCACC setup for optimal surround sound below to complete your surround setup. Subwoofer Listening position Surround left Surround right Depending on the size and characteristics of your room, you can choose to use the following setup option:1 • Front surround setup – This setup is ideal when rear surround speaker placement isn't possible or you want to avoid running long speaker cables in your listening area. The placement of speakers shown below allows for the creation of virtual surround sound. For HTZ363DVD: Center Front left Surround left Front right Subwoofer Surround right Using the Auto MCACC setup for optimal surround sound The Multichannel Acoustic Calibration (MCACC) system measures the acoustic characteristics of your listening area, taking into account ambient noise and testing for channel delay and channel level. After you have set up the microphone provided with your system, the receiver uses the information from a series of test tones to optimize the speaker settings and equalization (Acoustic Calibration EQ) for your particular room.2 Important • These test tones are loud; however, do not turn the volume down during setup as this may result in a sub-optimal calibration. Listening position Note 1 See Using Front Stage Surround Advance on page 16 to select a front surround mode when using this setup. 2 You only need to use the Auto MCACC setup once (unless you change the placement of your speakers or your room layout). 10 En HTZ363DVD_EN_WL.book 11 ページ 2007年2月3日 土曜日 午後3時13分 Getting started 02 DISPLAY CLEAR 0 TOP MENU TV CONTROL INPUT STANDBY /ON DVD/CD TUNER SOUND (FM/AM) RETRIEVER LINE 2 3 AUDIO SUBTITLE 4 7 5 6 ANGLE ZOOM 8 9 1 ENTER MCACC SHIFT ST HOME MENU F.S.SURR VOLUME MUTE VOLUME • If you see an ERR MIC or ERR SP message in the display, there may be a problem with your mic or the speaker connections. To try again, press ENTER when you see RETRY2. RETURN TUNE SURROUND TEST TONE ADVANCED SOUND 2 3 1 Connect the microphone to the MCACC MIC jack on the rear panel. COMPONENT VIDEO FM UNBAL 75 Ω IN MCACC HDMI OUT SETUP MIC CONTROL CR/ PR CB/ PB VIDEO S-VIDEO Français ANTENNA AM LOOP When the MCACC setup is complete, the volume level returns to normal and COMPLETE3 shows in the display, indicating that the MCACC setup is complete and Acoustic Calibration EQ has been activated.4 Deutsch USB PLAYLIST 1 CHANNEL SR SETUP ST OPEN/CLOSE SLEEP MENU TUNE • If the noise level is too high, NOISY blinks in the display for five seconds. To exit and check the noise levels1, press SHIFT+MCACC, or to try again, press ENTER when RETRY shows in the display. English • Make sure the mic and speakers are not moved during the MCACC setup. Y VIDEO OUT For ease of use, this system makes extensive use of graphical on-screen displays (OSDs). All the screens are navigated in basically the same way, using , , , to change the highlighted item and pressing ENTER to select it.5 3 If the system is off, press STANDBY/ON to turn the power on. If the tuner is selected, switch the input source. • Press SHIFT+MCACC to cancel and revert to the previous Auto MCACC settings. Button What it does HOME MENU Displays/exits the on-screen display Español 4 Press SHIFT+MCACC. Try to be as quiet as possible after pressing SHIFT+MCACC. The volume increases automatically and the system outputs a series of test tones. Important • Throughout this manual, ‘Select’ means use the cursor buttons to highlight an item on-screen, then press ENTER. Nederlands Make sure there are no obstacles between the speakers and the microphone. Using the on-screen displays Italiano 2 Place the microphone at your normal listening position. Place it about ear height, and make sure it is level by using a table or chair. Changes the highlighted menu item ENTER Selects the highlighted menu item Note 1 • If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary. • Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV during the Auto MCACC setup. 2 If this doesn’t work, press SHIFT+MCACC, turn off the power, and check the problem indicated by the ERR message, then try the Auto MCACC setup again. 3 If COMPLETE doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again. 4 See Listening with Acoustic Calibration EQ on page 16 to switch on/off Acoustic Calibration EQ. 5 The screen saver will appear after five minutes of inactivity. 11 En HTZ363DVD_EN_WL.book 02 12 ページ 2007年2月3日 土曜日 午後3時13分 Getting started Button What it does RETURN Returns to the main menu without saving changes Tip • The button guide at the bottom of every OSD screen shows you which buttons you’ll need to use for that screen. • If a disc contains a mixture of DivX video and other media file types (MP3, for example), first select whether to play the DivX video files (DivX) or the other media file types (MP3/WMA/JPEG/MPEG-4 AAC) from the on-screen display. 4 Adjust the volume. Use the VOLUME control. Basic playback controls Playing discs The basic playback controls for playing DVD, CD, Video CD/Super VCD, DivX video and WMA/MP3/MPEG-4 AAC discs are covered here. Further functions are detailed in chapter 4. The following table shows the basic controls on the remote for playing discs1. You can find other playback features in the chapter 4. Button What it does Starts/resumes normal playback. • If the display shows RESUME or LAST MEM playback starts from the resume or last memory point (see Resume and Last Memory below). Pauses/unpauses a disc. Stops playback or cancels the resume function (if the display shows RESUME). Press to start fast reverse scanning. Press to start fast forward scanning. Skips to the start of the current track or chapter, then previous tracks/chapters. Skips to the next track or chapter. 1 If the player isn’t already on, switch it on. If you’re playing a disc with video, also turn on your TV and make sure that it is set to the correct video input. 2 Press OPEN/CLOSE to load a disc. Load a disc with the label side facing up, using the disc tray guide to align the disc (if you’re loading a double-sided DVD disc, load it with the side you want to play face down). 3 Press (play) to start playback. If you’re playing a DVD or Video CD/Super VCD, a menu may appear. See DVD-Video disc menus and Video CD/Super VCD PBC menus on page 13 to navigate these. If you loaded a disc containing JPEGs, a slideshow will start. See Playing a JPEG slideshow on page 18 for more on this. Numbers Use to enter a title/chapter/track number. Press ENTER to select. • If the disc is stopped, playback starts from the selected title (for DVD) or track (for CD/Video CD/Super VCD). • If the disc is playing, playback jumps to the start of the selected title (VR mode DVD-R/-RW), chapter (DVDVideo) or track (CD/Video CD/Super VCD). Note 1 You may find with some DVD discs that some playback controls don’t work in certain parts of the disc. 12 En HTZ363DVD_EN_WL.book 13 ページ 2007年2月3日 土曜日 午後3時13分 Getting started Many DVD-Video discs contain menus from which you can select what you want to watch. Button What it does TOP MENU Displays the ‘top menu’ of a DVD MENU Displays a DVD disc menu — this varies with the disc and may be the same as the ‘top menu’. Moves the cursor around the screen. ENTER Selects the current menu option. RETURN Returns to the previously displayed menu screen. Numbers Highlights a numbered menu option (some discs only). Press ENTER to select. Video CD/Super VCD PBC menus Some Video CD/Super VCDs have menus from which you can choose what you want to watch. These are PBC (Playback control) menus. Numbers Selects numbered menu options. Press ENTER to select. Displays the previous menu page (if there is one). Displays the next menu page (if there is one). Listening to the radio The tuner can receive both FM and AM broadcasts, and lets you memorize your favorite stations so you don’t have to manually tune in every time you want to listen. 1 Press TUNER to switch to the tuner, then press repeatedly to select the AM or FM band. The display shows the band and frequency. 2 Tune to a frequency. There are three tuning modes — manual, auto, and high-speed: • Manual tuning: Press TUNE +/– repeatedly to change the displayed frequency. • Auto tuning: Press and hold TUNE +/– until the frequency display starts to move, then release. The tuner will stop on the next station it finds. Repeat to keep searching. Español Displays the PBC menu. Nederlands disc — this varies with the disc. What it does RETURN Italiano Sometimes DVD-Video menus are displayed automatically when you start playback; others only appear when you press MENU or TOP MENU. Button Français DVD-Video disc menus You can play a PBC Video CD/Super VCD without having to navigate the PBC menu by starting playback using a number button to select a track, rather than the (play) button. Deutsch When you stop playback of a disc, RESUME shows in the display indicating that you can resume playback from that point. With DVDs and Video CD/Super VCDs, even if ejected, the play position is stored in memory.1 The next time you load the disc, the display shows LAST MEM and you can resume playback. If you want to clear the resume point, press (stop) while RESUME is displayed. English Resume and Last Memory 02 • High-speed tuning: Press and hold TUNE +/– until the frequency display starts to move rapidly. Keep the button held down until you reach the frequency you want. If necessary, fine tune the frequency using the manual tuning method. Note 1 • The Last Memory function may not work with some discs. • For DVD-Video discs (except VR mode DVD-R/-RW), the player stores the play position of the last five discs. 13 En HTZ363DVD_EN_WL.book 02 14 ページ 2007年2月3日 土曜日 午後3時13分 Getting started Improving poor FM reception If you’re listening to an FM station in stereo but the reception is weak, you can improve the sound quality by switching to mono. 3 Use / to select the station preset you want then press ENTER. Listening to station presets 1 Tune to an FM radio station then press SHIFT+SETUP. 1 Make sure the TUNER function is selected. 2 Use / to choose FM MODE then press ENTER. 2 Use the ST +/– buttons to select a station preset. • You can also use the number buttons to do this. 3 Use / to select FM MONO then press ENTER. The mono indicator ( ) lights when the tuner is in mono reception mode. Select FM AUTO above to switch back to autostereo mode (the stereo indicator ( ) lights when receiving a stereo broadcast). Listening to other sources You can connect auxiliary sources (TV, satellite receiver, etc.) to this unit for playback through the speaker system. See Connecting auxiliary audio components on page 33 for more on this. Reducing AM reception noise If AM reception seems particularly poor, or the AM radio station you’re listening to seems noisy, try using the Noise Cut feature for better sound quality. 1 Tune to an AM radio station then press SHIFT+SETUP. 2 Use / to choose NOISECUT then press ENTER. 3 Use /to select the noise cut mode then press ENTER. Select an effect level between 1 and 3. Memorizing stations You can save up to 30 station presets so that you always have easy access to your favorite stations without having to tune in manually each time. 1 Tune to an AM or FM radio station. Select mono or auto-stereo reception (FM) or the Noise Cut mode (AM) as necessary. These settings are saved along with the preset. 2 Press SHIFT+SETUP and use / to choose ‘ST.MEM.’ then press ENTER. 14 En • To connect a USB device to the USB terminal, see USB playback on page 25. 1 Make sure that the external source (TV, satellite receiver, etc.) is switched on. 2 Press LINE to select the source. 3 If necessary, start playback of the source. HTZ363DVD_EN_WL.book 15 ページ 2007年2月3日 土曜日 午後3時13分 Listening to your system 03 Listening to your system The Auto listening mode is the simplest way to listen to any source as it was mastered: the output from the speakers mirrors the channels in the source material. MCACC F.S.SURR TUNE SURROUND ADVANCED SOUND TUNE SURROUND TEST TONE ADVANCED SOUND • Press SURROUND repeatedly to select a listening mode.1 The choices that appear in the display will vary according to the type of source that’s playing. • AUTO – Auto listening mode (see above) 1 With Dolby Pro Logic II Music mode active, press SOUND. 2 Use / to select ‘C WIDTH’, ‘DIMEN.’ or ‘PANORAMA’ then press ENTER to confirm. • C WIDTH (Center Width) – Provides a better blend of the front speakers by spreading the center channel between the front right and left speakers, making it sound wider (higher settings) or narrower (lower settings). • DIMEN. (Dimension) – Adjusts the depth of the surround sound balance from front to back, making the sound more distant (minus settings), or more forward (positive settings). Español • If you set up the system for Front surround (page 10), the Front Surround modes will give the best results. When listening in Dolby Pro Logic II Music mode, there are three settings you can adjust: Center Width, Dimension, and Panorama. Nederlands You can listen to stereo or multichannel sources in surround sound.2 Surround sound is generated from stereo sources using one of the Dolby Pro Logic decoding modes. Dolby Pro Logic II Music settings Italiano Listening in surround sound MCACC • STEREO – See Listening in stereo below TEST TONE • Press SURROUND to select the AUTO listening mode.1 F.S.SURR • MUSIC (Dolby Pro Logic II Music) – Pro Logic II 5.1 channel surround sound, especially suited to music sources (use with any two-channel source) Français • If you set up the system for Front surround (page 10), the Front Surround modes will give the best results. • MOVIE (Dolby Pro Logic II Movie) – Pro Logic II 5.1 channel surround sound, especially suited to movie sources (use with any two-channel source) Deutsch Auto listening mode English Chapter 3 • PANORAMA – Extends the front stereo image to include the surround speakers for a ‘wraparound' effect. • DOLBY PL (Dolby Pro Logic) – 4.1 channel surround sound (use with any two-channel source) Note 1 If the source is Dolby Digital or DTS, the corresponding indicator lights in the front panel display. 2 Note that when the tuner is selected, multichannel playback is not possible. 15 En HTZ363DVD_EN_WL.book 03 16 ページ 2007年2月3日 土曜日 午後3時13分 Listening to your system Using Front Stage Surround Advance The Front Stage Surround Advance modes are effective when you are using the Front surround speaker setup as described on page 10.1 0 TOP MENU MENU TUNE SR SETUP ST ENTER HOME MENU MCACC F.S.SURR ST RETURN TUNE SURROUND TEST TONE ADVANCED SOUND • Press ADVANCED to select an Advanced Surround mode. Press repeatedly to select ACTION, UNPLUGED, EXPANDED, TV SURR., SPORTS, ADV.GAME, VIRTUAL or X-STEREO (Extended Stereo). Listening in stereo You can listen to any source — stereo or multichannel — in stereo. When playing a multichannel source, all channels are downmixed to the front left/right speakers and the subwoofer. MCACC F.S.SURR • Press F.S.SURR to select a Front Stage Surround Advance mode. Press repeatedly to select FOCUS5.1, WIDE5.1 or EXTRAPWR. • FOCUS5.1 – Use to provide a rich surround sound effect directed to the center area where the left and right speakers’ sound projection converges. • WIDE5.1 – Use to provide a surround sound effect to a wider area than FOCUS5.1 mode. • EXTRAPWR – Outputs stereo sound (in the case of multi-channel sources, down-mixed stereo sound) from the surround speakers for powerful stereo effect. Using Advanced Surround The Advanced Surround effects can be used with any multichannel or stereo source for a variety of additional surround sound effects.1 These modes are designed to provide optimum listening effect when using the Standard surround setup described on page 10. MCACC F.S.SURR TUNE SURROUND When headphones are connected, only the STEREO (default) and PHONES SURROUND (virtual surround sound for headphones) modes are available. • With headphones connected, press ADVANCED to select PHONES SURROUND or SURROUND to select STEREO. Listening with Acoustic Calibration EQ You can listen to sources using the Acoustic Calibration Equalization set in Using the Auto MCACC setup for optimal surround sound on page 10.2 1 Press SOUND and use / to select MCACC EQ then press ENTER. SOUND Note En SOUND Listening with headphones 1 Note that when the tuner is selected, multichannel playback is not possible. 2 Acoustic Calibration EQ is not available when headphones are connected. 16 TEST TONE ADVANCED • Press SURROUND repeatedly until STEREO shows in the display. TEST TONE ADVANCED TUNE SURROUND HTZ363DVD_EN_WL.book 17 ページ 2007年2月3日 土曜日 午後3時13分 Listening to your system Using the Sound Retriever 1 Press SOUND and use / to select DIALOGUE then press ENTER. 2 Use / to select the amount of dialog enhancement then press ENTER to confirm. Select between OFF, MID or MAX. The Quiet listening feature reduces excessive bass or treble in a sound source. The Midnight listening feature allows you to hear effective surround sound of movies at low volume levels. • After pressing ENTER, the setting switches on/off. • To cancel the Quiet or Midnight listening modes, select BASS/TRE. Boosting the bass level There are two bass modes you can use to enhance the bass in a source.1 1 Press SOUND and use / to select BASSMODE then press ENTER. 2 Use / to adjust the sound then press ENTER to confirm. Select between OFF, MUSIC or CINEMA. Español The Dialog Enhancement feature is designed to make the dialog stand out from other background sounds in a TV or movie soundtrack. Quiet and Midnight modes Nederlands Enhancing dialog • Use / to select BASS or TREBLE then use / to adjust the tone. Press ENTER to confirm. Italiano • While listening to a stereo source, press SOUND RETRIEVER to switch the sound retriever on or off. Use the tone controls to adjust the bass and treble. Français When audio data is removed during the WMA/ MP3/MPEG-4 AAC compression process, sound quality often suffers from an uneven sound image. The Sound Retriever feature employs new DSP technology that helps bring CD quality sound back to compressed 2channel audio by restoring sound pressure and smoothing jagged artifacts left over after compression. Adjusting the bass and treble Deutsch • EQ ON is selected automatically after the Auto MCACC setup is completed. 2 Use / to select the option you want to adjust and press ENTER. The Bass/Treble, Quiet and Midnight features cannot be used at the same time. English 2 Use / to select EQ ON or EQ OFF then press ENTER to confirm. • If you select EQ OFF, equalization is set to off but speaker settings (channel delay and channel level) remain in effect. 03 Using the Tone controls You can change the tonal balance of the sound by using the tone control menu. 1 Press SOUND and use / to select TONE then press ENTER. Note 1 The Bass Mode is not available when headphones are connected. 17 En playing audio_video discs.fm 04 18 ページ 2007年2月5日 月曜日 午後4時8分 Disc playback features Chapter 4 Disc playback features Important • Many of the functions covered in this chapter apply to DVD discs, Video CDs/ Super VCDs, CDs, DivX video and WMA/ MP3/MPEG-4 AAC/JPEG discs, although the exact operation of some varies slightly with the kind of disc loaded. • Some DVDs restrict the use of some functions (random or repeat, for example) in some or all parts of the disc. This is not a malfunction. • When playing Video CD/Super VCDs, some of the functions are not available during PBC playback. If you want to use them, start the disc playing using a number button to select a track. Scanning discs You can fast-scan discs forward or backward at various different speeds.1 • During playback, press or to start scanning. Press repeatedly to increase the scanning speed (shown on-screen). • To resume playback, press (play).2 Playing in slow motion You can play DVDs, Video CD/Super VCDs and DivX video at four different forward slow motion speeds. DVD discs can also be played in reverse slow motion. 1 During playback, press (pause). 2 Press and hold / or / until slow motion playback starts. Press repeatedly to change the slow motion speed (shown on-screen). • To resume playback, press (play).2 Frame advance/frame reverse You can advance or back up DVD discs frameby-frame. With Video CD/Super VCDs and DivX video you can only use frame advance. 1 During playback, press (pause). 2 Press / or / to reverse or advance a frame at a time. • To resume playback, press (play).2 Playing a JPEG slideshow After loading a disc containing JPEG pictures, press to start a slideshow from the first folder/picture on the disc.3 The player displays the pictures in each folder in alphabetical order. • If the disc contains WMA/MP3/MPEG-4 AAC files, playback of the slideshow and audio files repeats. During audio playback, you can still use the skip (/), scan (/) and pause () functions. Pictures are automatically adjusted so that they fill as much of the screen as possible. Note 1 Only one speed is available for DivX video discs. 2 • Depending on the disc, normal playback may automatically resume when a new chapter is reached on a DVD disc. • For Video CDs/Super VCDs in PCB mode and WMA/MP3/MPEG-4 AAC tracks (in Scan Mode only), normal playback resumes when you reach the beginning or the end of a track. 3 • The time it takes for the player to load a file increases with large file sizes. • Discs can contain up to 299 folders and up to 648 folders and files combined. 18 En HTZ363DVD_EN_WL.book 19 ページ 2007年2月3日 土曜日 午後3時13分 Disc playback features While the slideshow is running: Pauses the slideshow (or audio); press again to restart. Jumps to the previous picture (or audio file with audio playback). Jumps to the next picture (or audio file with audio playback). /// Pauses the slideshow and SHIFT+ ZOOM Use the Disc Navigator to browse through the contents of a DVD or Video CD/Super VCD disc to find the part you want to play. 1 During playback, press HOME MENU and select ‘Disc Navigator’ from the onscreen menu. Disc Navigator 2 • Original: Title – Original titles from a VR mode DVD-R/-RW disc. • Playlist: Title – Playlist titles from a VR mode DVD-R/-RW disc. • Original: Time – Thumbnails from the Original content at 10 minute intervals. • Playlist: Time – Thumbnails from the Playlist at 10 minute intervals. The screen shows up to six moving thumbnail images displayed one after another. To display the previous/next six thumbnails, press / . 3 Select the thumbnail image for what you want to play. 01 02 03 04 05 06 Español Browsing DVD or Video CD/ Super VCD discs with the Disc Navigator • Time – Thumbnails from a Video CD/Super VCD disc at 10 minute intervals. Nederlands Displays the Disc Navigator screen (see below). • Track – Tracks from a Video CD/Super VCD disc. Italiano MENU Pauses the slideshow and zooms the picture. Press again to toggle between 1x, 2x and 4x zoom (Press (play) to restart slideshow). • Chapter – Chapters from the current title of a DVD-Video disc. Français rotates/flips the displayed picture (Press (play) to restart slideshow). • Title – Titles from a DVD-Video disc. Deutsch What it does The options available depend on the kind of disc loaded and whether the disc is playing or not, but include: English Button 04 Disc Navigator: Title 01- 49: - - You can use either /// and ENTER to select a thumbnail, or the number buttons. To select using the number buttons, enter a two-digit number then press ENTER. Select a view option. Disc Navigator Title Chapter 19 En HTZ363DVD_EN_WL.book 04 20 ページ 2007年2月3日 土曜日 午後3時13分 Disc playback features • When a JPEG file is selected, a slideshow begins, starting with that file, and continues to the end of the folder. Browsing WMA, MP3, MPEG-4 AAC, DivX video and JPEG files with the Disc Navigator Tip Use the Disc Navigator to find a particular file or folder by filename. • You can also play a JPEG slideshow while listening to WMA/MP3/MPEG-4 AAC playback. Simply select the audio file you want to listen to followed by the JPEG from which you want the slideshow to start. Playback of both the slideshow and the audio files repeats. Playback controls are effective for the JPEG slideshow only. 1 Press HOME MENU and select ‘Disc Navigator’ from the on-screen menu. 00:00/ 00:00 0kbps Folder1 Folder2 Folder3 • To play the contents of the whole disc rather than just the current folder, exit the Disc Navigator and start playback using the (play) button. Folder4 2 Use /// and ENTER to navigate. Use / to move up and down the folder/file list. Use to return to the parent folder.1 Use ENTER or to open a highlighted folder. • When a JPEG file is highlighted, a thumbnail image is displayed on the right. 00:00/ 00:00 0kbps Folder2 File1 File2 File3 File4 File5 3 To play the highlighted track or DivX video file or display the highlighted JPEG file, press ENTER. • When a WMA/MP3/MPEG-4 AAC or DivX video file is selected, playback begins from that file, and continues until the end of the folder. Using Playlists With this feature, you can make up to three playlists of 30 files each for discs containing WMA, MP3, MPEG-4 AAC and JPEG files. Since this unit will remember all playlists for the last ten discs you have loaded, this is useful for if you have a large number of files that you want to organize quickly and easily.2 Programming playlists 1 With the disc stopped, press HOME MENU and select ‘Disc Navigator’ from the on-screen menu. 2 Select the file you want to add to the playlist. See Browsing WMA, MP3, MPEG-4 AAC, DivX video and JPEG files with the Disc Navigator above if you don’t know how to do this. 3 Press PLAY LIST 1, 2 or 3. The file is added to the playlist you select. 4 Repeat steps 2 and 3 until you’re done. Note 1 You can also do this by going to the ‘..’ folder at the top, then pressing ENTER. 2 The disc must be loaded for the files in your playlist to play back. 20 En HTZ363DVD_EN_WL.book 21 ページ 2007年2月3日 土曜日 午後3時13分 Disc playback features 2 Listening to playlists Clearing files from a playlist Start playback of your playlist. Looping a section of a disc 1 During playback, press HOME MENU and select ‘Play Mode’. Play Mode Using repeat play In addition to various repeat play options, it’s also possible to use repeat play together with program play (see Creating a program list on page 22). 1 During playback, press HOME MENU and select ‘Play Mode’. 2 Select ‘Repeat’ then select a repeat play option.1 If program play is active, select Program Repeat to repeat the program list, or Repeat Off to cancel. • For DVD discs, select Title Repeat or Chapter Repeat. • For CDs and Video CD/Super VCDs, select Disc Repeat or Track Repeat. • For DivX video discs, select Title Repeat (or Repeat Off). Español The A-B Repeat function allows you to specify two points (A and B) within a track (CD, Video CD/Super Video CD) or title (DVD) that form a loop which is played over and over. To resume normal playback, select ‘Off’. Nederlands 2 From the ‘Disc Navigator’ screen, select the file you want to remove from the playlist and press CLEAR. 5 Italiano • If the playlist contains both JPEG and audio files, playback of the slideshow and audio files starts. 4 Press ENTER on ‘B(End Point)’ to set the loop end point. After pressing ENTER, playback jumps back to the start point and plays the loop. Français • With playback stopped, press PLAY LIST 1, 2 or 3. During playback, PGM lights in the front panel display. If no playlist has been programmed, NO LIST shows in the display. 3 Press ENTER on ‘A(Start Point)’ to set the loop start point. Deutsch • To add files without the on-screen display, simply press PLAY LIST 1, 2 or 3 during normal playback of the file you want (except when a JPEG slideshow is playing at the same time as audio). Select ‘A-B Repeat’. English Tip 1 04 Using random play Use this function to play titles or chapters (DVD-Video) or tracks (CD and Video CD/Super VCD) in a random order.2 1 During playback, press HOME MENU and select ‘Play Mode’. Note 1 You can’t use repeat play with WMA/MP3/MPEG-4 AAC discs. 2 • You can set the random play option when a disc is playing or stopped. However, you can’t use random play together with program play. • You can’t use random play with VR format DVD-R/-RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video discs, or while a DVD disc menu is being displayed. 21 En HTZ363DVD_EN_WL.book 04 22 ページ 2007年2月3日 土曜日 午後3時13分 Disc playback features 2 Select ‘Random’ then select an option. • For DVD discs, select Random Title or Random Chapter. After pressing ENTER to select the title/ chapter/track, the step number automatically moves down one. • For CDs and Video CD/Super VCDs, select On or Off to switch random play on or off. 4 Repeat step 3 to build up a program list. A program list can contain up to 24 steps. Tip • Use the following controls during random play: Button What it does Selects a new track/title/chapter at random. Returns to the beginning of the current track/title/chapter; further presses select another random track/title/chapter. • Random play remains in effect until you select Random Off from the random play menu options. • You can insert steps by just highlighting the position where you want the new step to appear and entering a title/chapter/track number. • To delete a step, highlight it and press CLEAR. 5 To play the program list, press (play). Program play remains active until you turn off program play (see below), erase the program list (see below), eject the disc or switch off. Tip • Use the following controls during program play: Button What it does Creating a program list HOME MENU Save the program list and exit without starting playback. This feature lets you program the play order of titles/chapters/tracks on a disc.1 Skip to the next step in the program list. 1 During playback, press HOME MENU and select ‘Play Mode’. 2 Select ‘Program’ then select ‘Create/Edit’ from the list of program options. 3 Use /// and ENTER to select a title, chapter or track for the current step in the program list. • For a DVD disc, you can add a title or a chapter. • For a CD or Video CD/Super VCD, select a track to add to the program list. Other functions available from the program menu There are a number of other options in the program menu in addition to Create/Edit. • Playback Start – Starts playback of a saved program list • Playback Stop – Turns off program play, but does not erase the program list • Program Delete – Erases the program list and turns off program play Note 1 You can’t use Program play with VR format DVD-R/-RW discs, WMA/MP3/MPEG-4 AAC discs, DivX video discs, or while a DVD disc menu is being displayed. 22 En HTZ363DVD_EN_WL.book 23 ページ 2007年2月3日 土曜日 午後3時13分 Disc playback features You can search DVD discs by title or chapter number, or by time; CDs and Video CD/Super VCDs by track number or time; DivX video discs by time. 3 Select a search mode. • The disc must be playing in order to use time search. Press ENTER to start playback. Some DVD discs and DivX video discs have subtitles in one or more languages; the disc box will usually tell you which subtitle languages are available. You can switch subtitle language during playback.1 Zooming the screen Using the zoom feature you can magnify a part of the screen by a factor of 2 or 4, while watching a DVD, DivX video title or Video CD/ Super VCD or playing a JPEG disc. 1 During playback, use the SHIFT+ZOOM button to select the zoom factor (Normal, 2x or 4x). 2 Use /// to change the zoomed area. You can change the zoom factor and the zoomed area freely during playback.4 Español Switching subtitles • Press SHIFT+AUDIO repeatedly to select an audio language option. • To set audio language preferences, see Language settings on page 30. Nederlands 5 When playing discs recorded with dialog in two or more languages, or with dual-mono audio2 you can switch these during playback.3 Italiano 4 Use the number buttons to enter a title, chapter or track number, or a time. • For a time search, enter the number of minutes and seconds into the currently playing title (DVD/ DivX video) or track (CD/ Video CD/Super VCD) you want playback to resume from. For example, press 4, 5, 0, 0 to have playback start from 45 minutes into the disc. For 1 hour, 20 minutes and 30 seconds, press 8, 0, 3, 0. Switching language/audio channels Français 2 Select ‘Search Mode’. The search options that appear depend on the kind of disc loaded. • See Displaying DivX subtitle files on page 41 for more on DivX subtitles. Deutsch 1 Press HOME MENU and select ‘Play Mode’. • Press SHIFT+SUBTITLE repeatedly to select a subtitle option. • To set subtitle preferences, see Language settings on page 30. English Searching a disc 04 Note 1 Some discs only allow you to change subtitle language from the disc menu. Press TOP MENU or MENU to access. 2 Some Super VCDs have two soundtracks. With these discs you can switch between the two soundtracks as well as individual channels in each. 3 Some discs only allow you to change audio language from the disc menu. Press TOP MENU or MENU to access. 4 • Since DVD, Video CD/Super VCD, DivX video title and JPEG pictures have a fixed resolution, picture quality will deteriorate, especially at 4x zoom. This is not a malfunction. • If the navigation square at the top of the screen disappears, press SHIFT+ZOOM again to display it. 23 En HTZ363DVD_EN_WL.book 04 24 ページ 2007年2月3日 土曜日 午後3時13分 Disc playback features Switching camera angles Some DVD discs feature scenes shot from two or more angles — check the disc box for details. When a multi-angle scene is playing, a icon appears on screen (this can be switched off if you prefer — see Display settings on page 30). • During playback (or when paused), press SHIFT+ANGLE to switch angle. Displaying disc information Various track, chapter and title information can be displayed on-screen during playback. • To show/switch/hide the information displayed, press DISPLAY repeatedly. Limited disc information also appears in the front panel display. Press DISPLAY to change the displayed information. 24 En HTZ363DVD_EN_WL.book 25 ページ 2007年2月3日 土曜日 午後3時13分 USB playback 05 English Chapter 5 USB playback 1 It is possible to listen to two-channel audio and watch JPEG files using the USB interface on the front of this unit. Connect a USB mass storage device2 as shown below. • Reconnecting the USB device with the player switched off. • Selecting to another input source (like DVD/CD), then back to USB. • Using a dedicated AC adapter (supplied with the device) for USB power. If this doesn’t remedy the problem, it is likely your USB device is incompatible. Basic playback controls The following table shows the basic controls on the remote for USB playback. Nederlands USB (Type A) Italiano 2 Connect your USB device. The USB terminal is located on the front panel. • Switch the player off, then on again. Français 1 With the player switched on, press USB. Make sure your TV is on and set to the correct video input. If a USB ERR message lights in the display, it may mean that the power requirements of the USB device are too high for this player, or that the device is incompatible. Try the following: Deutsch Important Using the USB interface Button What it does 3 Press (play) to start playback. If your USB device contains JPEGs, a slideshow will start. See Playing a JPEG slideshow on page 26 for more on this. • Make sure USB DATA is showing in the front panel display (or the system is in standby) when disconnecting. Starts normal playback. Pauses/unpauses playback. Stops playback. Press to start fast reverse scanning. Press to start fast forward scanning. Skips to the start of the current file, then previous files. Skips to the next file. Español USB mass storage device Note 1 This includes playback of WMA/MP3/MPEG-4 AAC files (except files with copy-protection or restricted playback). It is not possible to play DivX files through the USB terminal. 2 • Compatible USB devices include external magnetic hard drives, portable flash memory (particularly keydrives) and digital audio players (MP3 players) of format FAT16/32. It is not possible to connect this unit to a personal computer for USB playback. • Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no responsibility for any loss of data that may occur when connected to this unit. • With large amounts of data, it may take longer for the system to read the contents of a USB device. 25 En HTZ363DVD_EN_WL.book 05 26 ページ 2007年2月3日 土曜日 午後3時13分 USB playback Scanning files You can fast-scan forward or backward at various different speeds. • During playback, press or . Press repeatedly to increase the scanning speed (shown on-screen). • To resume playback, press (play).1 Playing a JPEG slideshow Press to start a slideshow from the first folder/picture.2 The pictures in each folder are displayed in order. • If the device contains WMA/MP3/MPEG-4 AAC files, playback of the slideshow and audio files repeats. During audio playback, you can still use the skip (/), scan (/) and pause () functions. Pictures are automatically adjusted so that they fill as much of the screen as possible. While the slideshow is running: Button What it does Pauses the slideshow (or audio); press again to restart. Jumps to the previous picture (or audio file with audio playback). Jumps to the next picture (or audio file with audio playback). /// Pauses the slideshow and rotates/flips the current picture (Press to restart slideshow). SHIFT+ ZOOM Pauses the slideshow and zooms the picture. Press again to toggle between 1x, 2x and 4x zoom (Press to restart slideshow). Button What it does MENU Displays the Navigator screen (see below). Browsing files with the Navigator Use the Navigator to find WMA, MP3, MPEG-4 AAC and JPEG files or folders by name.3 1 Press MENU then use /// and ENTER to navigate. Use / to move up/down the folder/file list. Use to return to the parent folder.4 Use ENTER or to open a highlighted folder. • When a JPEG file is highlighted, a thumbnail image is displayed on the right. 2 To play the highlighted track or display the highlighted JPEG file, press ENTER. • When a WMA/MP3/MPEG-4 AAC file is selected, playback begins from that file, and continues until the end of the folder. • When a JPEG file is selected, a slideshow begins, starting with that file, and continues to the end of the folder. Tip • You can also play a JPEG slideshow while listening to WMA/MP3/MPEG-4 AAC playback. Simply select the audio file you want to listen to followed by the JPEG from which you want the slideshow to start. Playback of both the slideshow and the audio files repeats. Playback controls are effective for the JPEG slideshow only. • To play all of the contents, rather than just the current folder, exit the Navigator and start playback using the (play) button. Note 1 With WMA/MP3/MPEG-4 AAC tracks, playback automatically resumes at the end or beginning of the track. 2 • The time it takes for the player to load a file increases with large file sizes. • USB devices can contain up to 299 folders and up to 648 folders and files combined. 3 Filenames may be displayed incorrectly with some digital audio players. 4 You can also do this by going to the ‘..’ folder at the top, then pressing ENTER. 26 En HTZ363DVD_EN_WL.book 27 ページ 2007年2月3日 土曜日 午後3時13分 Surround sound settings 06 Surround sound settings Channel level setting Use / to switch between channels in the following order: • • • • L – Front left speaker C – Center speaker R – Front right speaker SR – Surround right speaker Specifies dynamic range adjustment to Dolby Digital or some DTS soundtracks. If low level sound or dialog seem difficult to hear properly, this can help by bringing up the low level sounds, while controlling high level peaks. • DRC OFF (default) – No dynamic range adjustment (use when listening at higher volumes) • DRC MID – Mid setting • DRC HIGH – Dynamic range is reduced (loud sounds are reduced in volume while quieter sounds are increased) Español Set the relative channel levels from your main listening position.3 Dynamic Range Control Nederlands 2 Use / to adjust then press ENTER to confirm and exit. • Note that using the Auto MCACC (page 10) again overwrites the speaker settings. Specifies the distance from your listening position to your speakers. When DISTANCE appears, press ENTER, then use / to adjust the distance, and / to switch between the following speakers: • L – Front left speaker • C – Center speaker • R – Front right speaker • SR – Surround right speaker • SL – Surround left speaker • SW – Subwoofer Each speaker can be adjusted between 0.3 m and 9.0 m. The default setting is 3.0 m. Italiano 1 Press SHIFT+SETUP and use / then ENTER to choose the setting you want to adjust. The available settings are shown in the front panel display.2 Speaker distance setting Français From the Setup menu you can access all the surround sound settings of the system1, including channel levels, speaker distances and dynamic range adjustment. The Auto MCACC feature (page 10) should give you the best surround sound setup. However you may find that by further adjustment of the surround sound settings you can improve the surround sound in your listening room. • SL – Surround left speaker • SW – Subwoofer The channel level range is ±10 dB. Deutsch Using the Setup menu English Chapter 6 Note 1 There are other settings you can adjust from the Setup menu; these are explained in Improving poor FM reception on page 14 and Dimming the display on page 39. 2 The setup menu is exited automatically after 5 minutes of inactivity. 3 • You can’t adjust center/surround when Stereo or Virtual playback is selected (or with stereo sources using the Auto mode). • The Channel level setting is not available when headphones are connected. • The speaker volume can be adjusted at any time by pressing SHIFT+TEST TONE and then using / to adjust the channel levels. The test tone automatically moves from speaker to speaker in the order listed above. You should hear the test tone at the same volume from each speaker when seated in the main listening position. Press ENTER when you’re finished. • Since the subwoofer produces ultra-low frequencies it may seem quieter than it actually is. 27 En HTZ363DVD_EN_WL.book 07 28 ページ 2007年2月3日 土曜日 午後3時13分 Video Adjust menu Chapter 7 Video Adjust menu Video Adjust menu From the Video Adjust screen you can adjust settings that affect picture presentation. 1 Press HOME MENU and select ‘Video Adjust’ from the on-screen display. Video Adjust 2 Make settings using /// and ENTER. Video Adjust Sharpness Brightness Contrast Gamma Hue Chroma Level Standard 0 0 Off 0 0 You can adjust the following settings: • Sharpness – Adjusts the sharpness of edges in the picture (Fine, Standard, Soft) • Brightness – Adjusts the overall brightness (–20 to +20) • Contrast – Adjusts the contrast between light and dark (–16 to +16) • Gamma – Adjusts the ‘warmth’ of the picture (High, Medium, Low, Off) • Hue – Adjusts the red/green balance (Green 9 to Red 9) • Chroma Level – Adjusts how saturated colors appear (–9 to +9) Adjust the Brightness, Contrast, Hue and Chroma Level settings using /. Brightness min max 0 3 Press ENTER to return to the Video Adjust screen, or HOME MENU to exit. 28 En HTZ363DVD_EN_WL.book 29 ページ 2007年2月3日 土曜日 午後3時13分 Initial Settings menu 08 English Chapter 8 Initial Settings menu 1 Press DVD/CD. 2 With playback stopped, press HOME MENU and select ‘Initial Settings’. The Initial Settings menu provides audio and video output settings, parental lock settings, and display settings, among others. Initial Settings 3 Use /// and ENTER to select the setting and option you want to set. All the settings and options are explained on the following pages.1 What it means 4:3 (Letter Box) Set if you have a conventional 4:3 TV. Widescreen movies are shown with black bars top and bottom. 4:3 (Pan & Scan) Set if you have a conventional 4:3 TV. Widescreen movies are shown with the sides cropped so that the image fills the screen. 16:9 (Wide) Set if you have a widescreen TV. 16:9 (Compressed) Set if you have a widescreen TV. 4:3 material is shown with black bars on either side of the screen.2 1920x1080i Set if your TV supports 1920 x 1080 pixel interlace video. 1280x720p Set if your TV supports 1280 x 720 pixel progressive-scan video. 720x480p (NTSC)/ 720x576p (PAL) Set if your TV supports 720 x 480 (NTSC)/720 x 576 (PAL) pixel progressive-scan video. 720x480i (NTSC)/ 720x576i (PAL) Set if your TV supports 720 x 480 (NTSC)/720 x 576 (PAL) pixel interlace video. HDMI Resolution* (See Connecting using HDMI on page 35.) * Default changes with TV format (PAL/NTSC). Español Option TV Screen (See also Screen sizes and disc formats on page 43.) Nederlands Setting Italiano Video Output settings Français If an option is grayed out it means that it cannot be changed at the current time. This is usually because a disc is playing. Stop the disc, then change the setting. Deutsch Using the Initial Settings menu Note 1 • In the table, the default setting is shown in bold: other settings are shown in italics. • Some settings, such as TV Screen, Audio Language and Subtitle Language may be overridden by the DVD disc. Often these settings can also be made from the DVD disc menu. • The HDMI Resolution and HDMI Color settings only need to be set if you connected this player to an HDMI-compatible component using the HDMI connector. 2 This setting can only be used when you are connected via HDMI and have the HDMI resolution set to 1920x1080i or 1280x720p. When using this setting, only the HDMI connection is available. 29 En HTZ363DVD_EN_WL.book 08 30 ページ 2007年2月3日 土曜日 午後3時13分 Initial Settings menu Setting Option What it means HDMI Color (See Connecting using HDMI on page 35.) * Default changes depending on device connected. Full range RGB If colors are weak, this gives brighter colors and deeper black (default setting for HDMI-compatible DVI devices). RGB Use this setting if colors appear overly rich on the Full Range RGB setting. Component Outputs 8-bit component video format (default setting for HDMI-compatible devices). Component Out (See also Connecting using the component video output on page 34.) Interlace Set if your TV is not compatible with progressive scan video. Progressive Set if your TV is compatible with progressive scan video (see your TV’s instruction manual for details). Press ENTER once more to confirm (or RETURN to cancel). Note that progressive scan video is only output from the component video jacks. Language settings Setting Option What it means Audio Language English If there is an English soundtrack on the disc, it is played. Languages as displayed If there is a language selected on the disc, it is played. Other Language Select to choose a language other than the ones displayed (see Using the language code list on page 48). English If there are English subtitles on the disc they are displayed. Languages as displayed The subtitle language selected on the disc is displayed. Other Language Select to choose a language other than the ones displayed (see Using the language code list on page 48). w/Subtitle Lang. DVD disc menus are displayed in the same language as your selected subtitle language, if possible. Languages as displayed DVD menus are displayed in the selected language, if possible. Other Language Select to choose a language other than the ones displayed (see Using the language code list on page 48). On Subtitles are displayed in your selected subtitle language. Off Subtitles are always off by default when you play a DVD disc. Subtitle Language DVD Menu Language Subtitle Display Display settings 30 En Setting Option What it means OSD Language English On-screen displays of the player are in English. Languages as displayed On-screen displays are shown in the language selected. HTZ363DVD_EN_WL.book 31 ページ 2007年2月3日 土曜日 午後3時13分 Initial Settings menu 08 Option What it means Angle Indicator On A camera icon is displayed on-screen during multi-angle scenes on a DVD disc. Off No multi-angle indication is shown. Setting Option What it means Parental Lock – See Parental Lock below. DivX(R) VOD Display See About DivX® VOD content below. Changing your password • Default level: Off; Default password: none; Default Country/Area code: us (2119) Registering a new password 1 Select ‘Password’. Enter a new password and press ENTER. Setting/changing the Parental Lock 1 Select ‘Level Change’. 2 Use number buttons to enter your password, then press ENTER. 3 Select a new level and press ENTER. • Press repeatedly to lock more levels (more discs will require the password); press to unlock levels. You can’t lock level 1. Español Register a password to change the Parental Lock level or enter a Country/Area code.1 2 Nederlands Some discs also support the Country/Area Code feature. The player does not play certain scenes on these discs, depending on the Country/Area Code you set. 1 Select ‘Password Change’, input your existing password, then press ENTER. Italiano To give you some control over what your children watch on your DVD player, some DVDVideo discs feature a Parental Lock level. If your player is set to a lower level than the disc, the disc won’t play. To change your password, confirm your existing password then enter a new one. Français Parental Lock Deutsch Options settings English Setting Initial Settings Video Output Parental Lock Password Language Display DivX (R) VOD Level Change Country Code Options 2 Use the number buttons to input a fourdigit password then press ENTER. Note 1 • Not all discs use Parental Lock, and will play without requiring the password first. • If you forget your password, you’ll need to reset the player to register a new password (see Resetting the system on page 48). 31 En Initial settings menu.fm 08 32 ページ 2007年2月3日 土曜日 午後3時33分 Initial Settings menu Setting/changing the Country/Area code You can find the Country/Area code list on page 49. 1 Select ‘Country Code’, input your password, then press ENTER. 2 Select a Country/Area code then press ENTER. There are two ways you can do this: • Select by code letter: Use / to change the Country/Area code. • Select by code number: Press then use the number buttons to enter the four-digit Country/Area code. Displaying your DivX VOD registration code 1 Press HOME MENU and select ‘Initial Settings’. 2 Select ‘Options’, then ‘DivX (R) VOD’. Initial Settings Video Output Language Parental Lock DivX (R) VOD Display Display Options 3 Select ‘Display’. Your eight-digit registration code is displayed. The new Country/Area code takes effect after ejecting the disc once. Make a note of the code as you will need it when you register with a DivX VOD provider. About DivX® VOD content Playing DivX® VOD content In order to play DivX VOD (video on demand) content on this player, you first need to register the player with your DivX VOD content provider. You do this by generating a DivX VOD registration code, which you submit to your provider.1 Important • DivX VOD content is protected by a DRM (Digital Rights Management) system. This restricts playback of content to specific, registered devices. • If you load a disc that contains DivX VOD content not authorized for your player, the message Authorization Error is displayed and the content will not play. Some DivX VOD content may only be playable a fixed number of times. When you load a disc containing this type of DivX VOD content, the remaining number of plays is shown on-screen and you then have the option of playing the disc (thereby using up one of the remaining plays), or stopping. If you load a disc that contains expired DivX VOD content (for example, content that has zero remaining plays), the message Rental Expired is displayed. If your DivX VOD content allows an unlimited number of plays, then you may load the disc into your player and play the content as often as you like, and no message will be displayed. Note 1 Resetting the player (as described in Resetting the system on page 48) will not cause you to lose your registration code. 32 En Other connections.fm 33 ページ 2007年2月5日 月曜日 午後3時53分 Other connections 09 English Chapter 9 Other connections To audio output For an external AM antenna, use 5 m to 6 m of vinyl-insulated wire and set up either indoors or outdoors. Leave the loop antenna connected. Only use the included AM loop antenna. NENT DEO Tape deck, etc. CR/ PR LINE IN CB/ PB L Y R OUT R OUT FRONT L L CONTROL OUT R AUDIO R SURROUND L SPEAKERS (4 Ω • Connect the AUDIO IN jacks to the analog outputs of an external playback component. Connect using RCA pin-plug stereo cables. 5 m to 6 m AM LOOP For an external FM antenna, use a PAL connector to hook up an external FM antenna. The recording mode allows you to make surround-compatible analog recordings from the LINE OUT jacks1. Dolby multichannel sources are downmixed to stereo for improved playback with systems that can provide matrixdecoding (like Dolby Pro Logic). 1 PAL connector Using the stereo analog inputs, you can connect an external component such as a tape deck or MD player for playback through this system. 2 Use / to select a REC MODE, then press ENTER. 3 Use / to choose MODE ON or MODE OFF and then press ENTER to confirm. • MODE ON – A surround-compatible downmix (left-total/right-total, or Lt/Rt) of Dolby multichannel sources is output, (suitable for Dolby Surround Pro Logic or other matrix decoding). Español Connecting auxiliary audio components Press SOUND. Nederlands ANTENNA Recording mode Italiano Indoor antenna (vinyl-coated wire) Français Outdoor antenna Deutsch Connecting external antennas • MODE OFF – A simple stereo downmix (left-only/right-only, or Lo/Ro) is output (suitable for playback on a two-channel stereo system or on headphones. Note 1 • When the recording mode is on, most sound features cannot be used. The display will briefly blink REC MODE if you try and use a prohibited function while the recording mode is on. • When the recording mode is off, the audio from the analog output jacks may be interrupted, depending on the operation. • The recording mode switches off if you change the input function (DVD/CD, TUNER, etc.) or switch the power off. 33 En HTZ363DVD_EN_WL.book 09 34 ページ 2007年2月3日 土曜日 午後3時13分 Other connections Connecting the S-video output If your TV has an S-video input, you can use this instead of the standard video output for a better quality picture. • Use an S-video cable to connect the SVIDEO OUT to an S-video input on your TV. Line up the small triangle above the jack with the same mark on the plug before plugging in. Connecting using the component video output If your TV has component video inputs, you can use these instead of the standard video output to connect this system to your TV.1 This should give you a higher quality picture than the S-video output. • Use a component video cable to connect the COMPONENT VIDEO OUT to a set of component inputs on your TV. To S-video input TV To component input ANTENNA COMPONENT VIDEO AM LOOP FM UNBAL 75 Ω IN MCACC HDMI OUT SETUP MIC CONTROL VIDEO S-VIDEO TV CR/ PR CB/ PB L Y R ANTENNA COMPONENT VIDEO VIDEO OUT AM LOOP FM UNBAL 75 Ω IN MCACC HDMI OUT SETUP MIC CONTROL CR/ PR CB/ PB VIDEO S-VIDEO Y VIDEO OUT About progressive scan video Compared to interlace video, progressive scan video effectively doubles the scanning rate of the picture, resulting in a very stable, flickerfree image. Progressive scan video is available only from the component video output. Compatibility of this player with progressive-scan and high-definition TVs This player is compatible with progressive video Macro Vision System Copy Guard.2 Note 1 The component video output is switchable between interlaced and progressive formats. See Video Output settings on page 29. 2 Consumers should note that not all high-definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output (Interlace). If there are questions regarding our TV set compatibility with this model, please contact our customer service center. 34 En HTZ363DVD_EN_WL.book 35 ページ 2007年2月3日 土曜日 午後3時13分 Other connections 09 1 If you have a HDMI or DVI (with HDCP) equipped monitor or display, you can connect it to this player using a commercially available HDMI cable for high quality digital video.1 To HDMI connector 3 Use / to choose the setting you want then press ENTER. • AUDIO ON – Audio signals are output through the HDMI interconnect • AUDIO OFF – Switches off HDMI audio Resetting the HDMI connection If you get an error message (the display shows HDMI ERR) or if the screen goes blank (for example, after changing the resolution), check the troubleshooting guide on page 46. If this doesn’t solve the problem, follow the steps below to reset the HDMI connection. 1 COMPONENT VIDEO AM LOOP FM UNBAL 75 Ω IN VIDEO S-VIDEO CR/ PR LINE IN CB/ PB L Y R R OUT FRONT L CENTER L CONTROL OUT R SUB MCACC HDMI OUT SETUP MIC CONTROL VIDEO OUT AUDIO WOOFER R SURROUND L SPEAKERS (4 Ω - 6 Ω) 2 Press SHIFT+SETUP and use / to choose HDMI INI then press ENTER. The system will restart and the HDMI settings are automatically reset to the factory defaults. See Video Output settings on page 29 for more on these settings. Nederlands • The arrow on the cable connector body should be face up for correct alignment with the connector on the player. Switch the system into standby. Italiano HDMI-compatible display ANTENNA Français • Use an HDMI cable to connect the HDMI OUT interconnect on this player to an HDMI interconnect on a HDMI-compatible monitor. 2 Press SHIFT+SETUP and use / to choose HDMI OUT then press ENTER. Deutsch See About HDMI below for more about the HDMI connection. Switch the system into standby. English Connecting using HDMI About HDMI Switching the HDMI audio setting To listen to audio from the HDMI interconnect, make sure you’ve specified the HDMI audio output setting. Español You can also adjust the HDMI settings for resolution and color. For more on these settings see Video Output settings on page 29. HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for use with DVD players, DTV, set-top boxes, and other AV devices. HDMI was developed to provide the technologies of High Bandwidth Digital Content Protection (HDCP) as well as Digital Visual Interface (DVI) in one specification. HDCP is used to protect digital content transmitted and received by DVI-compliant displays. Note 1 • An HDMI connection can only be made with DVI-equipped components compatible with both DVI and High Bandwidth Digital Content Protection (HDCP). If you choose to connect to a DVI connector, you will need a separate adaptor (DVIHDMI) to do so. A DVI connection, however, does not support audio signals. Consult your local audio dealer for more information. • Depending on the component you have connected, using a DVI connection may result in unreliable signal transfers. • When you change the component connected to the HDMI output, you will also need to change the HDMI settings to match the new component (see Video Output settings on page 29 to do this). 35 En HTZ363DVD_EN_WL.book 09 36 ページ 2007年2月3日 土曜日 午後3時13分 Other connections HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multichannel surround-sound audio. HDMI features include uncompressed digital video, a bandwidth of up to 2.2 gigabytes per second (with HDTV signals), one connector (instead of several cables and connectors), and communication between the AV source and AV devices such as DTVs. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC. Using this unit with a Pioneer plasma television If you have a Pioneer plasma television1, you can use an SR+ cable2 to connect it to this unit and take advantage of various convenient features, such as controlling this unit via the plasma television’s remote sensor, automatic video input switching of the plasma television, and automatic volume muting on the plasma television. Important • When using the CONTROL IN jack for the first time, you must first remove the protective seal that covers the jack. • With an SR+ cable connected, the remote must now be pointed towards your plasma television rather than the remote sensor of this unit in order to control this system. • Use a 3-ringed miniplug SR+ cable to connect the CONTROL IN jack of this unit through a media receiver to the CONTROL OUT jack of your plasma television.3 Before you can use the extra SR+ features, you need to make a few settings in the unit. See SR+ Setup for Pioneer plasma televisions below for detailed instructions. SR+ Setup for Pioneer plasma televisions Make the following settings if you have connected a Pioneer plasma television to this unit using an SR+ cable. Note that the number of video inputs available will depend on the plasma television you’ve connected. 1 CONTROL OUT Pioneer plasma television ANTENNA COMPONENT VIDEO AM LOOP FM UNBAL 75 CR/ PR CB/ PB VIDEO IN S-VIDEO MCACC HDMI OUT SETUP MIC CONTROL Y VIDEO OUT Press SHIFT+SR+ on the remote. 2 Use the / to select SETUP, then press ENTER. 3 Use / to select the setting you want. • VoL.C OFF – This unit does not control the volume of the plasma television. • VOL.C ON – When this unit is switched to one of the inputs that use the plasma television (DVD, or another one of functions below), the volume on the plasma television is muted so only sound from this system is heard. Note 1 This system is compatible with all Pioneer plasma televisions from 2003 onward. 2 The 3-ringed SR+ cable from Pioneer is commercially available under the part number ADE7095. Contact the Pioneer Customer Support division for more information on obtaining an SR+ cable. 3 You won’t be able to use the remote sensor of this unit with the CONTROL IN jack of this unit connected to the CONTROL OUT jack of your plasma television. You can use the remote sensor of the plasma television (even in standby) as long as the power isn’t switched off. 36 En HTZ363DVD_EN_WL.book 37 ページ 2007年2月3日 土曜日 午後3時13分 Other connections When you're finished, press ENTER. 1 Press SHIFT+SR+ on the remote. • If you disconnect the SR+ cable or switch the plasma television off while SR+ is on, the SR+ ON setting remains. When this unit is connected to both another device and a plasma television, you can control all components by pointing their respective remote controls at the sensor for the plasma television. Español • The SR+ setting is maintained even after switching this system into standby then back on. Automatic muting will be effective when this system is switched on. Nederlands 2 Use / to select SR+ ON then press ENTER. To switch SR+ control off, select SR+ OFF. • Using a cable with mono mini-plugs on either side (sold separately), connect the CONTROL IN jack on another Pioneer component to the CONTROL OUT jack on this unit. This will allow you to control the other component by pointing its remote at this unit. Italiano Switching on the SR+ mode If you choose to use this feature, you must make sure that you also have at least one set of analog audio jacks connected to another component for grounding purposes. Français 5 Many Pioneer components support SR CONTROL connections, by which you can use the remote controls of any connected components by aiming them at the sensor of just one component. When you use a remote control, the control signal is passed along the chain to the appropriate component. This can be useful when you have multiple components contained inside an entertainment center. Deutsch This matches this unit’s input source with a numbered video input on the plasma television.1 For example, select the LN PDP3 setting if the video output of your line component is connected to video input 3 on the plasma television. TVTN switches the plasma television to its built-in tuner and NONE leaves the plasma television input as is (no switching takes place). About control out connections English 4 Assign any input source connected to the plasma television to the corresponding input number. Use / to select the source (DVD, LN (LINE) or USB), then / to select the input number. 09 Note 1 The PDP5 input may be called ‘PC Input’ (or similar) on your plasma television. 37 En HTZ363DVD_EN_WL.book 10 38 ページ 2007年2月3日 土曜日 午後3時13分 Additional information Chapter 10 Additional information Optional system settings All the available settings in the standby setup menu are listed below. See the notes in each section for more information about the settings. The first setting in each section is the default. 1 Switch the system into standby. 2 Press SHIFT+SETUP and use / then ENTER to choose the setting you want to adjust. The available settings are shown in the front panel display.1 3 Use / to adjust then press ENTER to confirm and exit. System demo setting Switches the automatic demo feature on or off (this starts when you plug in for the first time): TV system setting The default setting of this system is AUTO, and unless you notice that the picture is distorted when playing some discs, you should leave it set to AUTO. If you find picture distortion with some discs, set the TV system to match your country or region’s system. However, this may restrict the kinds of disc you can watch. See the table for the kinds of discs compatible with each setting (AUTO, PAL and NTSC).2 • After using / to choose TV SYS (step 2 above), press ENTER to change the TV system as follows: • AUTO NTSC • NTSC PAL • PAL AUTO The system automatically switches on and you’ll see the new TV system setting in the display after seeing WELCOME.3 Player setting • DEMO ON – Switches the demo feature on. • DEMO OFF – Switches the demo feature off. Frequency step setting If you find that you can’t tune into stations successfully, the frequency step may not be suitable for your country/region. • AM 9K • AM 10K Media Type Format NTSC PAL AUTO DVD/Super VCD/ Video CD/DivX Video NTSC NTSC PAL NTSC PAL NTSC PAL PAL CD/MP3/WMA/ MPEG-4 AAC/ JPEG/no disc — NTSC PAL NTSC or PAL DTS CD setting If you play a DTS-encoded CD, you will need to change this setting to hear the decoded signal. Note 1 The setup menu is exited automatically after 5 minutes of inactivity. 2 Most models of the newly developed countdown PAL TV system detect 50 Hz (PAL)/60 Hz (NTSC) and automatically switch vertical amplitude, resulting in a display without vertical shrinkage. However, in some cases, the image may appear without color. If your PAL TV does not have a V-Hold control, you may not be able to watch NTSC discs because of picture roll. If the TV has a V-Hold control, adjust it until the picture stops rolling. On some TVs, the picture may shrink vertically, leaving black bands at the top and bottom of the screen. 3 You have to switch the player into standby (press STANDBY/ON) before each change. 38 En HTZ363DVD_EN_WL.book 39 ページ 2007年2月3日 土曜日 午後3時13分 Additional information • DTS-CD – Proper decoding of DTSencoded CDs; the beginning of regular CD tracks my be skipped. • LOCK ON – Makes the front panel buttons and controls inoperative. • LOCK OFF – Restores regular use of the front panel buttons and controls. This player is compatible with a wide range of disc types (media) and formats. Playable discs will generally feature one of the following logos on the disc and/or disc packaging. Note however that some disc types, such as recordable CD and DVD, may be in an unplayable format. Setting the sleep timer DVD-Video • Press SLEEP repeatedly to select an option. Choose between the following options: Audio CD DVD-R Video CD DVD-RW CD-R CD-RW Italiano The sleep timer switches off the system after about an hour so you can fall asleep without worrying about it.1 Français See the Disc compatibility table below for more information. Deutsch Key lock setting Disc/content format playback compatibility English • NORMAL – Regular CD playback; some DTS-encoded CDs output a noisy signal. 10 • SLP ON – Switches off after about an hour After selecting SLP ON, you can press SLEEP again to check how much time is left. Each line indicates approximately 12 minutes (remaining): • This unit will play DVD+R/+RW discs. • • is a trademark of FUJIFILM Corporation. is a trademark of DVD Format/Logo Licensing Corporation. • Also compatible with KODAK Picture CD. Dimming the display You can adjust the brightness of the text in the front panel display. When the display is set to a darker color, the Power Indicator is turned off. 1 Press SHIFT+SETUP and use / to select DIMMER then press ENTER. Español SLP - - - - - Fujicolor CD Nederlands • SLP OFF – Cancels the sleep timer This player supports the IEC’s Super VCD standard for superior picture quality, dual soundtracks, and widescreen support. VIDEO CD Super Video CD (Super VCD) 2 Use / to adjust then press ENTER to confirm and exit. • LIGHT – Brighter setting • DARK – Darker setting Note 1 The display dims when the sleep timer is set, and the power indicator is turned off. 39 En HTZ363DVD_EN_WL.book 10 40 ページ 2007年2月3日 土曜日 午後3時13分 Additional information About DualDisc playback A DualDisc is a new two -sided disc, one side of which contains DVD content video, audio, etc. while the other side contains non-DVD content such as digital audio material. The non-DVD, audio side of the disc is not compliant with the CD Audio specification and therefore may not play. The DVD side of a DualDisc plays in this product. DVD-Audio content will not play. For more detailed information on the DualDisc specification, please refer to the disc manufacturer or disc retailer. Disc compatibility table 40 En Media Compatible formats CD-R/-RW • CD-Audio, Video CD/Super VCD, ISO 9660 CD-ROM* * ISO 9660 Level 1 or 2 compliant. CD physical format: Mode1, Mode2 XA Form1. Romeo and Joliet file systems are both compatible. • Multi-session playback: No • Unfinalized disc playback: No DVD-R/-RW • DVD-Video (Video mode), Video Recording (VR)*, UDF Bridge DVD-ROM * Edit points may not play exactly as edited; screen may go momentarily blank at edited points. • Multi Border playback: No • Unfinalized playback: No PC-created disc • Discs recorded using a PC may not be playable due to the setting of the software used to create the disc. In these instances, check the DVD-R/RW or CD-R/-RW software manual or disc boxes for more on compatibility. • Discs recorded in packet write mode are not compatible. Media Compatible formats Compressed • MPEG-1 Audio Layer 3 (MP3), audio Windows Media Audio (WMA), MPEG4 AAC • Sampling rates: 32 kHz/44.1 kHz/ 48 kHz • Bit-rates: Any (128 kbps or higher recommended) • VBR (variable bit rate) MP3/WMA/ MPEG-4 AAC playback: No • WMA lossless encoding: No • DRM (Digital Rights Management) compatible: Yes (DRM-protected audio files will not play in this player.) • File extensions: .mp3, .wma, .m4a (these must be used for the player to recognize MP3/WMA/MPEG-4 AAC files) • File structure (may differ): Up to 299 folders on a disc; up to 648 folders and files (combined) within each folder JPEG file • Baseline JPEG and EXIF 2.2* still image files up to a resolution of 3072 x 2048 *File format for digital still cameras • Progressive JPEG compatible: No • File extensions: .jpg (must be used for the player to recognize JPEG files) • File structure (may differ): Up to 299 folders on a disc; up to 648 folders and files (combined) within each folder About DVD+R/DVD+RW compatibility Only DVD+R/DVD+RW discs recorded in ‘Video Mode (DVD Video Mode)’ which have been finalized, can be played back. However, some editing made during the recording may not be played back accurately. HTZ363DVD_EN_WL.book 41 ページ 2007年2月3日 土曜日 午後3時13分 Additional information • Official DivX® Certified product. The font sets listed below are available for DivX external subtitle files. You can see the proper font set on-screen by setting the Subtitle Language (in Language settings on page 30) to match the subtitle file.2 Group 1: Albanian (sq), Basque (eu), Catalan (ca), Danish (da), Dutch (nl), English (en), Faroese (fo), Finnish (fi), French (fr), German (de), Icelandic (is), Irish (ga), Italian (it), Norwegian (no), Portuguese (pt), About WMA This player can playback Windows Media Audio content. WMA is an acronym for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA content can be encoded by using Windows Media® Player version 7.7.1, Windows Media® Player for Windows® XP, or Windows Media® Player 9 series. Español Displaying DivX subtitle files Apple and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries. Nederlands • File extensions: .avi and .divx (these must be used for the player to recognize DivX video files). Note that all files with the .avi extension are recognized as MPEG4, but not all of these are necessarily DivX video files and therefore may not be playable on this player. Advanced Audio Coding (AAC) is at the core of the MPEG-4 AAC standard, which incorporates MPEG-2 AAC, forming the basis of the MPEG-4 audio compression technology. The file format and extension used depend on the application used to encode the AAC file. This unit plays back AAC files encoded by iTunes® bearing the extension ‘.m4a’. DRM-protected files will not play, and files encoded with some versions of iTunes® may not play, or filenames may display incorrectly. Italiano • Plays all versions of DivX® video (including DivX®6) with standard playback of DivX® media files.1 About MPEG-4 AAC Français DivX video compatibility DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license. Deutsch DivX is a compressed digital video format created by the DivX® video codec from DivX, Inc. This player can play DivX video files burned on CD-R/-RW and DVD-R/-RW/-ROM discs. Keeping the same terminology as DVD-Video, individual DivX video files are called ‘Titles’. When naming files/titles on a CD-R/-RW or DVD-R/-RW disc prior to burning, keep in mind that by default they will play in alphabetical order. Rhaeto-Romanic (rm), Scottish (gd), Spanish (es), Swedish (sv) Group 2: Albanian (sq), Croatian (hr), Czech (cs), Hungarian (hu), Polish (pl), Romanian (ro), Slovak (sk), Slovenian (sl) Group 3: Bulgarian (bg), Byelorussian (be), Macedonian (mk), Russian (ru), Serbian (sr), Ukrainian (uk) Group 4: Hebrew (iw), Yiddish (ji) Group 5: Turkish (tr) English About DivX 10 Note 1 Playback of .avi video files larger than 4 GB is not possible. 2 • For external subtitle files the following subtitle format filename extensions are supported (please note that these files are not shown within the disc navigation menu): .srt, .sub, .ssa, .smi • Some external subtitle files may be displayed incorrectly or not at all. • The filename of the movie file has to be repeated at the beginning of the filename for the external subtitle file. • The number of external subtitle files which can be switched for the same movie file is limited to a maximum of 10. 41 En HTZ363DVD_EN_WL.book 10 42 ページ 2007年2月3日 土曜日 午後3時13分 Additional information Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. This product includes technology owned by Microsoft Corporation and cannot be used or distributed without a license from Microsoft Licensing, Inc. Using and taking care of discs Handling discs Hold the disc by its edges when handling so as not to leave fingerprints, dirt or scratches on either side of the disc. Damaged or dirty discs can affect playback performance. If a disc becomes marked with fingerprints, dust, etc., clean using a soft, dry cloth. This unit is designed for use with conventional, fully circular discs only. Pioneer disclaims all liability arising in connection with the use of shaped discs. DVD Video regions All DVD Video discs carry a region mark that indicates which region(s) of the world the disc is compatible with. Your DVD system also has a region mark (on the rear panel). Discs from incompatible regions will not play in this player. In this instance, the following message appears on-screen: Incompatible disc region number Can’t play disc Discs marked ALL play in any player. Installation and maintenance Hints on installation Wipe lightly from the center of the disc using straight strokes. Don’t wipe the disc surface with circular strokes. If necessary, use a cloth soaked in alcohol, or a commercially available CD/DVD cleaning kit to clean a disc more thoroughly. Never use benzine, thinner or other cleaning agents such as those designed for cleaning vinyl records. Storing discs Avoid leaving discs in excessively cold, humid, or hot environments (including under direct sunlight). Don’t glue paper or put stickers onto the disc, or use a pencil, ball-point pen or other sharp-tipped writing instrument. These could all damage the disc. Discs to avoid Discs spin at high speed inside the player. If a disc is cracked, chipped, warped, or otherwise damaged, don’t risk using it in your player— you could end up damaging the unit. 42 En We want you to enjoy using this system for years to come, so please bear in mind the following points when choosing a location: Do... Use in a well-ventilated room. Place on a solid, flat, level surface, such as a table, shelf or stereo rack. Don’t... Use in a place exposed to high temperatures or humidity, including near radiators and other heat-generating appliances. Place on a window sill or other place where the system will be exposed to direct sunlight. Use in an excessively dusty or damp environment. Place directly on top of an amplifier, or other component in your stereo system that becomes hot in use. Use near a television or monitor as you may experience interference — especially if the television uses an indoor antenna. Use in a kitchen or other room where the system may be exposed to smoke or steam. HTZ363DVD_EN_WL.book 43 ページ 2007年2月3日 土曜日 午後3時13分 Additional information Problems with condensation Set to 4:3 (Letter Box), widescreen discs are shown with black bars top and bottom. Set to 4:3 (Pan&Scan), widescreen discs are shown with the left and right sides cropped. Although the picture looks larger, you don’t actually see the whole picture. Español If you need to move the main unit, first remove a disc if there’s one in the player, then press STANDBY/ON on the front panel to turn the system off. Wait for GOOD BYE to disappear from the display, then unplug the power cord.1 Never lift or move the unit during playback — discs rotate at high speeds and may damage. Nederlands Moving the system unit Italiano Condensation may form inside the player if it is brought into a warm room from outside, or if the temperature of the room rises quickly. Although the condensation won’t damage the player, it may temporarily impair performance. Leave it to adjust to the warmer temperature for about an hour before switching on. Televisions also come in different aspect ratios; ‘standard’ 4:3 and widescreen 16:9.3 Français The DVD player’s lens should not become dirty in normal use, but if for some reason it should malfunction due to dust or dirt, consult your nearest Pioneer authorized service center. Although lens cleaners are commercially available, we do not recommend using them since some may damage the lens. DVD-Video discs come in different screen aspects, ranging from TV programs, which are generally 4:3, to CinemaScope widescreen movies2, with an aspect ratio of up to about 7:3. Deutsch Cleaning the pickup lens Screen sizes and disc formats English Use on a thick rug or carpet, or cover with cloth — this may prevent proper cooling of the system unit. Place on an unstable surface, or one that is not large enough to support all four of the system unit’s feet. 10 Note 1 Unplugging the unit before GOOD BYE disappears from the display may cause the system to return to the factory settings. 2 Many widescreen discs override the system’s settings so that the disc is shown in letterbox format regardless of the setting. 3 • Using the 16:9 (Wide) setting with a standard 4:3 TV, or one of the 4:3 settings with a widescreen TV, will result in distortion. • When you watch discs recorded in 4:3 format, you can use the TV controls to select how the picture is presented. Your TV may offer various zoom and stretch options; see the instructions that came with your TV for details. • Some movie aspect ratios are wider than 16:9, so even with a widescreen TV, these discs will still play in a ‘letterbox’ style. 43 En HTZ363DVD_EN_WL.book 10 44 ページ 2007年2月3日 土曜日 午後3時13分 Additional information Troubleshooting Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work. • If the system does not operate normally due to external effects such as static electricity disconnect the plug from the outlet and insert again to return to normal operating conditions. General Problem Remedy The power does not turn on, or switches off suddenly (an error message may be displayed at startup). • Wait for one minute before switching back on. • Make sure there are no loose strands of wire touching the unit. This could cause the system to shut off automatically. • Check that the speakers are connected correctly. • Make sure the voltage of the mains power source is correct for the model. • Try reducing the volume level. • If the problem persists, take it to your nearest Pioneer authorized service center or your dealer for servicing. No sound is output when a function is selected. • If you’re using the line input, make sure the component is connected correctly (see Connecting auxiliary audio components on page 33). • Press MUTE on the remote control to turn muting off. • Turn up the volume. No sound from surround • Refer to Channel level setting on page 27 to check the speaker levels. or center speakers. • When TUNER is selected, you can only hear the source in stereo. • Check that you haven’t selected the AUTO, STEREO or VIRTUAL mode (see Listening to your system on page 15). • Connect the speakers properly (refer to the Setup Guide). • If the source is 96 kHz, it will be played in stereo. Can’t operate the remote • Replace the batteries (refer to the Setup Guide). control. • Operate within 7 m, 30° of the remote sensor (refer to the Setup Guide). • Remove any obstacles or operate from another position. • Avoid exposing the remote sensor on the front panel to direct light. • Check that there’s nothing mistakenly plugged into the CONTROL IN jack. • If the system is connected to a Pioneer plasma television with an SR+ cable, check that the plasma television is switched on. Point the remote control at the plasma television in order to operate the system. • To operate other Pioneer components, make sure that the control cable and analog audio cable are connected. TRAYLOCK shows in the • Press and hold OPEN/CLOSE on the front panel for about eight seconds. Then display and the tray can’t the tray can be opened/closed using OPEN/CLOSE. be ejected. 44 En HTZ363DVD_EN_WL.book 45 ページ 2007年2月3日 土曜日 午後3時13分 Additional information Remedy SND. DEMO shows in the display and the unit can’t be controlled. • Press and hold (stop) on the front panel for about five seconds. The disc tray ejects automatically to indicate the Sound Demo mode is disabled. The disc is ejected automatically after loading. • Clean the disc and align the disc properly in the disc guide. • If the region number on a DVD-video disc does not match the number on the player, the disc cannot be used (see DVD Video regions on page 42). In this instance, the following message appears on screen: Incompatible disc region number/Can’t play disc. • Allow time for any condensation inside the player to evaporate. Avoid using the player near an air-conditioning unit. Playback not possible. • If the disc is loaded upside down, reload the disc with label side face up. Picture playback stops and buttons cannot be used. • Press (stop), then (play) to start playback again. • Switch the power off once, then on again using the front panel STANDBY/ON button. • Check that connections are correct and that plugs are inserted fully. • Check the manual of the TV/monitor to make sure the settings are correct. • If the Progressive setting is selected and you have used component video cables to connect a TV that is not compatible with a progressive scan signal, you will not be able to see any picture at all. With your TV connected using either the composite or S-video terminals, change the Component Out setting to Interlace (see Video Output settings on page 29). Screen is stretched or aspect doesn’t change. • The TV Screen setting is incorrect. Set the TV Screen option to match the TV/ monitor you're using (see Video Output settings on page 29). When recorded on a VCR or passed through an AV selector, there is disturbance in the playback picture. • This system uses copy-protection technology which may prevent recording or cause picture problems when connected through a VCR or AV selector. This is not a malfunction. Español • When the power is cut, settings will be canceled. No picture/No color. Nederlands Settings are canceled. Italiano Remedy Français Problem Deutsch DVD/CD/Video CD player English Problem 10 Picture disturbance • This player is compatible with Macro-Vision System copy guard. Some discs during playback or dark. include a copy prevention signal, and when this type of disc is played back, stripes etc., may appear on some sections of the picture depending on the TV. This is not a malfunction. • Discs respond differently to particular player functions. This may result in the screen becoming black for a brief instant or shaking slightly when the function is executed. These problems are largely due to differences between discs and disc content and are not malfunctions of this player. Noticeable difference in • DVDs and CDs use different recording methods. This is not a malfunction. DVD and CD volume. 45 En HTZ363DVD_EN_WL.book 10 46 ページ 2007年2月3日 土曜日 午後3時13分 Additional information Problem Remedy CD-ROM disc is not recognized. • Make sure that the CD-ROM was recorded using the ISO 9660 disc format. See Disc compatibility table on page 40 for more on disc compatibility. DVD-ROM disc is not recognized. • Make sure that the DVD-ROM was recorded using the UDF bridge format. See Disc compatibility table on page 40 for more on disc compatibility. Files don’t show up in the Disc Navigator/ Photo Browser. • The files on the disc must be named with the correct file extension: .mp3 for MP3 files; .wma for WMA files; .m4a for MPEG-4 AAC files; .jpg for JPEG files (upper or lower-case is OK). See Disc compatibility table on page 40. Can’t play WMA or MPEG-4 AAC files. • The files were recorded using DRM (digital rights management). This is not a malfunction. Tuner Problem Remedy Considerable noise in radio broadcasts. • Connect the AM antenna (refer to the Setup Guide) and adjust the direction and position for best reception. You may also connect an additional internal or external AM antenna (refer to Connecting external antennas on page 33). • Fully extend the FM wire antenna, position for best reception, and secure to a wall. You may also connect an outdoor FM antenna (see Connecting external antennas on page 33). • Turn off other equipment that may be causing the noise or move it further away. • The tuning interval is incorrect for your country or region. See Frequency step setting on page 38 to switch the tuning interval. Auto tuning does not pick up some stations. • The radio signal is weak. Auto tuning will only detect radio stations with a good signal. For more sensitive tuning, connect an outdoor antenna. USB connection Problem Remedy USB mass storage • Make sure you have completely inserted the USB connector to this unit. device is not recognized • Check that the memory format is FAT16 or FAT32. by the system. • USB devices with an internal USB hub are not supported. Files don’t show up in the Navigator/Photo Browser. • The files must have the correct file extension: .mp3 for MP3 files; .wma for WMA files; .m4a for MPEG-4 AAC files; .jpg for JPEG files (upper or lower-case is OK). • Make sure the file permission hasn’t been restricted (through a password, etc.). Can’t play WMA or MPEG-4 AAC files. • The files were recorded using DRM (digital rights management). This is not a malfunction. HDMI connection 46 En Problem Remedy No HDMI audio output. • See Switching the HDMI audio setting on page 35 to make sure that AUDIO ON is selected. HTZ363DVD_EN_WL.book 47 ページ 2007年2月3日 土曜日 午後3時13分 Additional information • Depending on the connected equipment, some HDMI Color settings may cause the picture to be displayed incorrectly. In this case, use the TV’s own video input settings to select RGB, if possible. Alternatively, revert to the previous HDMI Color setting. Error Messages • An operation is prohibited because it is only applicable to 2 channel sources, while the current source is a multichannel source. 96K • An operation is prohibited because the source is 96 kHz digital. REC MODE • An operation is prohibited because the Recording mode is on (page 33). SND. DEMO • The sound demo is on. See General in Troubleshooting on page 44. NOISY • Background noise is too high to complete MCACC setup successfully. ERR MIC • An error occured during MCACC setup because the microphone is not connected or is not connected properly. ERR SP • An error occured during MCACC setup because the speakers are not connected or are not connected properly. MUTING • An operation is prohibited because the sound is muted (press MUTE). STEREO • An operation is prohibited because the tuner is selected. TRAYLOCK • The tray lock is on. See General in Troubleshooting on page 44. KEYLOCK • The key lock is enabled. See Key lock setting on page 39. PHONESIN • An operation is prohibited because the headphones are connected. HDMI ERR • See HDMI connection above for troubleshooting tips. See also Resetting the HDMI connection on page 35 if the problem persists. USB ERR • See Important in Using the USB interface on page 25 for more on this. Español Description 2CH ONLY Nederlands Message Italiano Color problems occur with your monitor after changing the HDMI Color setting (page 30). Français • Make sure that you’ve selected this player as the HDMI input in the settings for the component you’re using (refer to the component’s instruction manual). • Check that the HDMI cable is connected properly and isn’t damaged. • Check that components connected using the HDMI interface are switched on and HDMI compatible (components must be compatible with both DVI and High Bandwidth Digital Content Protection (HDCP)). • Depending on the component you have connected, using a DVI connection may result in unreliable signal transfers. • Make sure the resolution on this player matches that of the component you have connected using HDMI. See Video Output settings on page 29 to change the HDMI resolution. • If the screen goes blank after changing the resolution, it means the you selected a resolution incompatible with your monitor. See Resetting the HDMI connection on page 35 to reset to the factory defaults. Deutsch Remedy No HDMI video output. English Problem 10 47 En HTZ363DVD_EN_WL.book 10 48 ページ 2007年2月3日 土曜日 午後3時13分 Additional information Message Description EEP ERR • Contact your Pioneer authorized service center or your dealer for servicing. EXIT • Appears when a menu is automatically exited after a set period of inactivity. Resetting the system Using the language code list Use the front panel controls to reset all system settings to the factory default. Some of the language options (see Language settings on page 30) allow you to set your preferred language from any of the 136 languages in the Language code list below. • With the system on, press STANDBY/ ON while holding down USB. The next time you switch on, all the system settings should be reset. 1 Select ‘Other Language’. 2 Use / to select either a code letter or a code number. 3 Use / to select a code letter or a code number. See the Language code list below for a complete list of languages and codes. 48 En HTZ363DVD_EN_WL.book 49 ページ 2007年2月3日 土曜日 午後3時13分 Additional information 10 Language (Language code letter), Language code Nederlands Español Slovak (sk), 1911 Slovenian (sl), 1912 Samoan (sm), 1913 Shona (sn), 1914 Somali (so), 1915 Albanian (sq), 1917 Serbian (sr), 1918 Siswati (ss), 1919 Sesotho (st), 1920 Sundanese (su), 1921 Swedish (sv), 1922 Swahili (sw), 1923 Tamil (ta), 2001 Telugu (te), 2005 Tajik (tg), 2007 Thai (th), 2008 Tigrinya (ti), 2009 Turkmen (tk), 2011 Tagalog (tl), 2012 Setswana (tn), 2014 Tonga (to), 2015 Turkish (tr), 2018 Tsonga (ts), 2019 Tatar (tt), 2020 Twi (tw), 2023 Ukrainian (uk), 2111 Urdu (ur), 2118 Uzbek (uz), 2126 Vietnamese (vi), 2209 Volapük (vo), 2215 Wolof (wo), 2315 Xhosa (xh), 2408 Yoruba (yo), 2515 Zulu (zu), 2621 Italiano Lingala (ln), 1214 Laothian (lo), 1215 Lithuanian (lt), 1220 Latvian (lv), 1222 Malagasy (mg), 1307 Maori (mi), 1309 Macedonian (mk), 1311 Malayalam (ml), 1312 Mongolian (mn), 1314 Moldavian (mo), 1315 Marathi (mr), 1318 Malay (ms), 1319 Maltese (mt), 1320 Burmese (my), 1325 Nauru (na), 1401 Nepali (ne), 1405 Norwegian (no), 1415 Occitan (oc), 1503 Oromo (om), 1513 Oriya (or), 1518 Panjabi (pa), 1601 Polish (pl), 1612 Pashto, Pushto (ps), 1619 Portuguese (pt), 1620 Quechua (qu), 1721 Rhaeto-Romance (rm), 1813 Kirundi (rn), 1814 Romanian (ro), 1815 Kinyarwanda (rw), 1823 Sanskrit (sa), 1901 Sindhi (sd), 1904 Sangho (sg), 1907 Serbo-Croatian (sh), 1908 Sinhalese (si), 1909 Français Esperanto (eo), 0515 Estonian (et), 0520 Basque (eu), 0521 Persian (fa), 0601 Finnish (fi), 0609 Fiji (fj), 0610 Faroese (fo), 0615 Frisian (fy), 0625 Irish (ga), 0701 Scots-Gaelic (gd), 0704 Galician (gl), 0712 Guarani (gn), 0714 Gujarati (gu), 0721 Hausa (ha), 0801 Hindi (hi), 0809 Croatian (hr), 0818 Hungarian (hu), 0821 Armenian (hy), 0825 Interlingua (ia), 0901 Interlingue (ie), 0905 Inupiak (ik), 0911 Indonesian (in), 0914 Icelandic (is), 0919 Hebrew (iw), 0923 Yiddish (ji), 1009 Javanese (jw), 1023 Georgian (ka), 1101 Kazakh (kk), 1111 Greenlandic (kl), 1112 Cambodian (km), 1113 Kannada (kn), 1114 Kashmiri (ks), 1119 Kurdish (ku), 1121 Kirghiz (ky), 1125 Latin (la), 1201 Deutsch Japanese (ja), 1001 English (en), 0514 French (fr), 0618 German (de), 0405 Italian (it), 0920 Spanish (es), 0519 Dutch (nl), 1412 Russian (ru), 1821 Chinese (zh), 2608 Korean (ko), 1115 Greek (el), 0512 Afar (aa), 0101 Abkhazian (ab), 0102 Afrikaans (af), 0106 Amharic (am), 0113 Arabic (ar), 0118 Assamese (as), 0119 Aymara (ay), 0125 Azerbaijani (az), 0126 Bashkir (ba), 0201 Byelorussian (be), 0205 Bulgarian (bg), 0207 Bihari (bh), 0208 Bislama (bi), 0209 Bengali (bn), 0214 Tibetan (bo), 0215 Breton (br), 0218 Catalan (ca), 0301 Corsican (co), 0315 Czech (cs), 0319 Welsh (cy), 0325 Danish (da), 0401 Bhutani (dz), 0426 English Language code list Country/Area code list Country/Area, Country/Area code, Country/Area code letter Argentina, 0118, ar Australia, 0121, au Austria, 0120, at Belgium, 0205, be Brazil, 0218, br Canada, 0301, ca Chile, 0312, cl China, 0314, cn Denmark, 0411, dk Finland, 0609, fi France, 0618, fr Germany, 0405, de Hong Kong, 0811, hk India, 0914, in Indonesia, 0904, id Italy, 0920, it Japan, 1016, jp Korea, Republic of, 1118, kr Malaysia, 1325, my Mexico, 1324, mx Netherlands, 1412, nl New Zealand, 1426, nz Norway, 1415, no Pakistan, 1611, pk Philippines, 1608, ph Portugal, 1620, pt Russian Federation, 1821, ru Singapore, 1907, sg Spain, 0519, es Switzerland, 0308, ch Sweden, 1905, se Taiwan, 2023, tw Thailand, 2008, th United Kingdom, 0702, gb United States of America, 2119, us 49 En Additional_information.fm 10 50 ページ 2007年2月3日 土曜日 午後5時34分 Additional information S-DV363 Speaker system Specifications • • Amplifier section RMS Power Output: Front, Center, Surround . . . 100 W per channel (1 kHz, 10 % T.H.D., 4 Ω) Subwoofer. . . 100 W (100 Hz, 10 % T.H.D., 4 Ω) • Disc section Digital audio characteristics . . . . . . . . . DVD fs: 96 kHz, 24-bit Type . . . . . . . DVD system, Video CD/Super VCD system and Compact Disc digital audio system Frequency response . . . . . . . . . . . 4 Hz to 44 kHz (96 kHz sampling) / 4 Hz to 22 kHz (48 kHz sampling) Wow and Flutter . . . . . . . .Limit of measurement (±0.001 % W.PEAK) or less (JEITA) • FM tuner section Frequency range . . . . . . . . 87.5 MHz to 108 MHz Antenna . . . . . . . . . . . . . . . . . . 75 Ω, unbalanced • AM tuner section Frequency range: With 9 kHz step . . . . . . . . 531 kHz to 1602 kHz With 10 kHz step . . . . . . . 530 kHz to 1700 kHz Antenna . . . . . . . . . . . . . . . . . . . . . .Loop antenna • Miscellaneous Power requirements. . . AC 220 V to 240 V, 50 Hz/60 Hz Power consumption . . . . . . . . . . . . . . . . . . . 55 W Power consumption in standby. . . . . . . . .0.30 W Dimensions . . . . . . . 420 mm (W) x 60 mm (H) x 332 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3 kg • Accessories (DVD/CD receiver) Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . AA/R6 dry cell batteries . . . . . . . . . . . . . . . . . . . (to confirm system operation) Video cable (yellow plugs) . . . . . . . . . . . . . . . . . AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . Microphone (for Auto MCACC setup) . . . . . . . . Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup Guide These operating instructions 50 En 1 2 1 1 1 1 1 Front/surround speakers Enclosure . . . . . . . . . . Closed-box bookshelf type (magnetically shielded) System . . . . . . . . . . . . . . . . 7.7 cm 1-way system Speakers . . . . . . . . . . . . . . . . . . 7.7 cm cone type Nominal impedance . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . . 80 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . . .100 W Dimensions . . . . . . .100 mm (W) x 100 mm (H) x 100 mm (D) Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.54 kg • Center speaker Enclosure . . . . . . . . . . Closed-box bookshelf type (magnetically shielded) System . . . . . . . . . . . . . . . . 7.7 cm 1-way system Speakers . . . . . . . . . . . . . . . . . . 7.7 cm cone type Nominal impedance . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . . 75 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . . .100 W Dimensions . . . . . . . . 220 mm (W) x 90mm (H) x 100 mm (D) Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.70 kg • Subwoofer Enclosure . . . . . . .Bass-reflex floorstanding type System . . . . . . . . . . . . . . . . . 16 cm 1-way system Speaker . . . . . . . . . . . . . . . . . . . . 16 cm cone type Nominal impedance . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . 30 Hz to 2.5 kHz Maximum Input Power . . . . . . . . . . . . . . . .100 W Dimensions . . . . . 221 mm (W) x 401.5 mm (H) x 390 mm (D) Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 kg • Accessories Speaker cables. . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Screws (for brackets). . . . . . . . . . . . . . . . . . . . . . 4 Non-skid pads (small) . . . . . . . . . . . . . . . . . . . . 16 Non-skid pads (large) . . . . . . . . . . . . . . . . . . . . . 4 S-DV2T Speaker system • Front speakers Enclosure . . . . . . .Closed-box floorstanding type (magnetically shielded) System . . . . . . . . . . . . . . . . . . . . . . .2-way system HTZ363DVD_EN_WL.book 51 ページ 2007年2月3日 土曜日 午後3時13分 Additional information Surround speakers Accessories Speaker cables. . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Non-skid pads (small) . . . . . . . . . . . . . . . . . . . . . 8 Non-skid pads (large) . . . . . . . . . . . . . . . . . . . . . 8 Speaker stand bases . . . . . . . . . . . . . . . . . . . . . . 2 Screws (for bases) . . . . . . . . . . . . . . . . . . . . . . . . 6 • Front/surround speakers Same as S-DV2T Front speakers (see above). • Center speaker Same as S-DV363 Center speaker (see above). • Accessories Speaker cables. . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Non-skid pads (large) . . . . . . . . . . . . . . . . . . . . 16 Speaker stand bases . . . . . . . . . . . . . . . . . . . . . . 4 Screws (for bases) . . . . . . . . . . . . . . . . . . . . . . . 12 S-DV2SW Speaker system • Subwoofer Same as S-DV363 Subwoofer (see above). DRM (digital rights management) copy protection is a technology designed to prevent unauthorized copying by restricting playback, etc. of compressed audio files on devices other than the PC (or other recording equipment) used to record it. For detailed information, please see the instruction manuals or help files that came with your PC and/or software. Español S-DV4T Speaker system This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. Nederlands • This product includes FontAvenue® fonts licenced by NEC corporation. FontAvenue is a registered trademark of NEC Corporation. Italiano Enclosure . . . . . . . . . . Closed-box bookshelf type (magnetically shielded) System . . . . . . . . . . . . . . . . 7.7 cm 1-way system Speakers. . . . . . . . . . . . . . . . . . .7.7 cm cone type Nominal impedance . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . . 80 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . . .100 W Dimensions . . . . . . . 100 mm (W) x 100 mm (H) x 100 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.54 kg Note • Specifications and design subject to possible modification without notice, due to improvements. Français • Accessories Speaker cables . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Non-skid pads (large) . . . . . . . . . . . . . . . . . . . . . 4 Deutsch • Center speaker Same as S-DV363 Center speaker (see above). • English Speakers: Woofer . . . . . . . . . . . . . . . . . .7.7 cm cone typex2 Tweeter . . . . . . . . . . . . . 2.6 cm semi-dome type Nominal impedance . . . . . . . . . . . . . . . . . . . . 4 Ω Frequency range . . . . . . . . . . . . . 70 Hz to 20 kHz Maximum input power . . . . . . . . . . . . . . . .100 W Dimensions . . . . 260 mm (W) x 1096.3 mm (H) x 260 mm (D) Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 kg 10 Manufactured under license from Dolby Laboratories.“Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories. “DTS” and “DTS Digital Surround” are registered trademarks of DTS, Inc. Published by Pioneer Corporation. Copyright © 2007 Pioneer Corporation. All rights reserved. 51 En HTZ363DVD_EN_WL.book 52 ページ 2007年2月3日 土曜日 午後3時13分 PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411 PIONEER EUROPE NV Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11 PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300 PIONEER ELECTRONICS DE MEXICO S.A. DE C.V. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270 K002_B_En Printed in <XRE3161-A>