Download Miele F 1803 Vi Specification Sheet
Transcript
Fully Integrated 30” Freezer F 1813 Vi / F 1803 Vi 8mieleusa.com Fully Integrated 30” Freezer F 1813 Vi / F 1803 Vi FOR FLUSH INSTALLATION 25" m 84" in.* 4" 29 3/ 24 5/ 8" EPTS ACC UNIT STOM A CU PANEL NT FRO O 30" 10 1/ 4 Location Codes E - 5 foot - 120 Volt - 15 Amp 3-wire molded plug power supply connects lower left rear O - Standard NEMA 5-15 Duplex Outlet - locate less than 9" above finished floor W - 1/4" flexible water line - tape to floor 4 1/8 " 6 5/8" - 8 1/2" 1 1/8 " 2" - 8 3/8" E 83 1/2" - 85 3/8" W Notes • All Installations must be done in accordance with local codes • Sides of adjoining cabinets should be filled (flush to frame) to insure proper fit and finish • For Proud Installation - please adjust accordingly * Depth assumes a 3/4” panel, please adjust according to custom panel thickness F 1813 Vi / F 1803 Vi Page 2 of 6 Fully Integrated 30” Freezer F 1813 Vi / F 1803 Vi CUSTOM PANEL INSTALLATIONS These units do not come equipped with a front panel. They are designed to accept a custom door panel supplied by the cabinet maker. Miele has a unique panel integration system which allows the panels to align with the surrounding cabinets. Panel size is determined in the following manner: Width: 29 3/4" in all cases Thickness: Minimum 3/4" outside frame Panel Height = HOC - TKH HOC = Total height of cabinet or side panel TKH = Toe-kick height HOC Panel Height Height: Determined using the following calculation: Note: Miele Fully Integrated Freezer Finish back side of panels to insure appearance Panel may extend above unit. This is not considered in height calculation Maximum panel weight: 105.8 Pounds TKH Panel Notes If the adjoining cabinets are taller than the height of machine (HOM) - the front panel may be extended accordingly. Simply maintain the toekick height and extend the panel the needed distance. Adjoining cabinet Extended Panel Machine F 1813 Vi / F 1803 Vi Page 3 of 6 Fully Integrated 30” Freezer F 1813 Vi / F 1803 Vi HINGING DETAILS 90° Door 115° Door Thickness options Thickness options 0-1/8" 0-1/8" 0-3/4" 1" 1-1/4" 1-1/2" 1-3/4" 0-3/4" 1" 1-1/4" 1-1/2" 1-3/4" 2" Cabinet Front Cabinet Front 1" Fro nt P ane l 0-3/4" 1-1/2" 1-1/4" 1" 1-1/4" Front Panel 0-3/4" 1-1/2" Door Swing Door Swing 14 3/8" MAX 32 11/16" 7/16" NOTE: Additional space needed depending on the thickness of front panels and handle used. Freezer units cannot be stop pinned at 90° NOTE: Additional space needed depending on the thickness of front panels and handle used. Freezer units cannot be stop pinned at 90° F 1813 Vi / F 1803 Vi Page 4 of 6 Fully Integrated 30” Freezer F 1813 Vi / F 1803 Vi HINGING DETAILS 115° Door Thickness options 0-1/8" 0-3/4" 1" 1-1/4" 1-1/2" 1-3/4" Cabinet Front 13/8”(35mm) 11/6” (29.6mm) 17/24” (18mm) 1/4”(6.4mm) 25/8” (67mm) 21/3” (59mm) 21/24”(52mm) 3/4” 1 (44.5mm) 3”(76.2mm) F r o nt P ane l 0-3/4" 1" 1-1/4" 1-1/2" Door Swing 16 7/8" MAX F 1813 Vi / F 1803 Vi Page 5 of 6 Fully Integrated 30” Freezer F 1813 Vi / F 1803 Vi 90° Door HINGING DETAILS FOR INSTALLATION WITH APPLIANCE/OBJECT ON HINGE SIDE Thickness options Thickness 0-1/8" 7/16” 13/16” (11 mm) (30mm) 1-1/2" 1-3/4" 0-3/4" 1" 1-1/4" 1-1/2" 1-3/4" 2" 17/16” (36.5mm) 111/16” (43mm) 115/16” (49.2mm) Cabinet Front 1" 1-1/4" Front Panel 0-3/4" Handle or object that is NOT flush with Cabinet Front. 1-1/2" Door Swing Door Sw 16 7/ MAX 38 11/16" 7/16" **When installing hing side next to an appliance or object that is within range of the door panel, limit the door opening angle to 90O. This is done by installing the banking pin as illustrated.Insert the banking pin through the holes and drive in with a hammer. F 1813 Vi / F 1803 Vi Page 6 of 6