Download Lincoln Impinger 1600 Series User's Manual

Capacity Estimates | Pies Per Hour:
BAKE TIME
Pie Size
3 min.
3½ min.
4 min.
4½ min.
5 min.
5½ min.
6 min.
6½ min.
7 min.
12” (30 cm)
182
155
135
120
108
99
90
84
78
14” (36 cm)
115
99
87
88
69
63
58
53
50
16” (41 cm)
101
87
76
67
61
55
51
47
44
Ventilation Requirements:
Ventilation is required. Local codes prevail. These are the “authority having jurisdiction” as stated by the
National Fire Protection Association, Inc., in NFPA 96-1994. Estimates of CFM requirements can vary from
2400 to as high as 6000 CFM exhaust. In all cases the ambient temperature around the oven must not
exceed 95°F (35°C) when the oven is operating. This information is shown as a guideline for ventilating
the Impinger® 1600 Ovens.
18-24”
(457 mm 610mm)
94” (2388 mm)
70” (1778 mm)
CAPTURE AREA
CAPTURE AREA
CAPTURE
VELOCITY
50 FPM
CAPTURE VELOCITY 50 FPM
8”
(203 mm)
6”
(153 mm)
8”
(203 mm)
6”
(153 mm)
78”
(1981 mm)
1. Dimensions shown are for ovens without long extension shelves. The outside end of the conveyor
frame must be a minimum of eight (8) inches (203 mm) inside the canopy as shown.
2. The capture velocity across the lower edge of the canopy is to be 50 FPM at sides and front.
3. Use filters at rear exhaust area of the hood, as shown. Do not just put an opening into a 4 sided canopy.
4. The ovens are to be centered in the canopy space left-to-right and front-to-back if possible.
5. A six (6) inch space at rear of oven is recommended for utilities.
6. Use of a Type I or Type II application and overall final installation is determined per local codes.
7. Recommended 2400-3000 CFM exhaust, typical, or higher per local codes; as a guideline to obtain
adequate capture velocity.
8. Recommended 80% of make-up air provided outside of the canopy through perforated metal diffusers directed straight down... not at the oven; located at front , side or both.
9. Room air diffusers must not be directed onto the oven and should be positioned a minimum of
three (3) feet from the perimeter of the hood to keep airflow from affecting the oven.
NOTE: Specifications subject to change without notification.
1111 North Hadley Road
P.O. Box 1229
Fort Wayne, Indiana 46801-1229
Tel 1.260.459.8200
Fax 1.260.436.0735
E mail [email protected]
web www.lincolnfp.com
©2007 Lincoln Foodservice Products, Inc.
Printed in the U.S.A.
1256-2.5K-04/07-SP
1600 Series | Impinger® Low Profile Single Belt Conveyorized Oven
Global
1600 Series Impinger® Low Profile
Single Belt Conveyorized Oven
Models:
1600-000-U
1622-000-U
1628-000-N
1634-000-E
1601-000-U
1623-000-U
1629-000-N
1635-V00-E
1621-000-E
1624-000-U
1633-000-E
1636-V00-E
Benefits:
1637-000-E
Standard Features:
• Faster bake times improve
• Stackable up to three (3) oven
• Advanced Air Impingement
• 32” (812 mm) wide, 73” (1854
• Improved product flow
• 40” (1016 mm) baking
time of service.
Technology enhances bake
quality and uniformity.
during cooking reduces
operation costs.
cavities high.
mm) long conveyor belt with
product stop.
chamber.
• Research and Applications
support for continued
operational success.
• Temperature is adjustable from
250°F (121°C) to 600°F (316°C).
• Conveyor speed is adjustable
• Enodis Star service support
is committed to ongoing
customer satisfaction.
from one (1) minute to thirty
(30) minutes cooking time.
• Dual heating systems for
• New FastBake ™ Technology
designed to bake up to 35%
faster than other conveyor
ovens without increased
noise levels or loss of product
quality! (Optional)
maximized cooking efficiency.
• Front-loading access door with
cool handle.
• Customer-specific setups give
customer very specific results.
• Indirect conveyor drive is
powered by an AC motor.
• Stainless Steel top, front and
Lincoln Impinger ® Conveyor Ovens are
the premier continuous cook platform
for the food service industry. Using the
latest advancements in air impingement
technology, Impinger ® Ovens allow for
rapid heating, cooking, baking, and
crisping of foods, typically done two
to four times faster than conventional
ovens.
Easy to Operate:
• Digital controls with single
on/off power switch.
•
Microprocessor controlled
bake time/conveyor speed.
• Improved view vacuum
florescent readout displays
set temperatures in degrees
(F° or C°), conveyor belt
speed, thermostat indicator
light, and diagnostic
messages for easy trouble
shooting.
1111 North Hadley Road
P.O. Box 1229
Fort Wayne, Indiana 46801-1229
• All settings are automatically
locked out to eliminate
accidental changes.
sides.
• Oven Start-Up/Check-Out
by Enodis Star service agent
included in price.
Easy to Clean:
• Front door for easy cleaning
and removal of finger
assemblies.
• Conveyor is removable
through the right side
opening.
Optional Features:
• FastBake™ Upgrade: Improve
your bake time by up to
35% without increased noise
levels or loss of product
quality!
• Entry and exit shelves.
• Flexible gas connector.
• Cleaning kit (#1050)
Tel 1.260.459.8200
Fax 1.260.436.0735
E mail [email protected]
web www.lincolnfp.com
Approved by The Canadian Standards Association
www.lincolnfp.com
1600 Series | Impinger® Low Profile Single Belt Conveyorized Oven
Global
Global
Gas Supply Pressure Recommendations:
Supply (Inlet) Pressure (mbar)
Recommended
Minimum
Gas Pipe Size
Natural
9-14” WC (2.2 kPA / 22.4 mbar - 3.5kPa / 34.9 mbar)
2” (51 mm)
LP
11-14” WC (2.7 kPa / 27.36 mbar - 3.5 kPa / 34.9 mbar)
2” (51 mm)
Gas Type
*Gas supply pressures are dependent on local gas type and on all applicable local codes. Agency approved flexible
connection to each oven must be minimum¾” (19 mm) NPT and length must not exceed six (6) feet (1829 mm).
Electrical Service:
Each oven deck requires voltage, phase and hertz as indicated by model number. Neutral must be grounded
at electrical service and receptacle properly polarized. Gas 120V units have a cord with NEMA 5-15 plug.
All other models have terminal block connections. It is recommended that a separate circuit breaker be
provided for each oven deck.
Recommended Minimum Clearances:
Rear of oven to combustible surface: 6” (152 mm). Clearance on each side from other cooking equipment: 24”
(610 mm). Clearance required to remove conveyor for cleaning: 11’ (3553 mm).
Warranty:
All new impinger® ovens installed in the United States and Canada come with a one (1) year parts and labor
warranty starting from the date of start-up/check-out. All ovens installed in locations other than the US and
Canada are warranted for one (1) year parts and ninety (90) days labor starting from the date of start-up/
check-out. Start-up/check-out must occur within 24 months of date of manufacture.
General Information:
All 1600 Models
Length
Depth
Height
Single
Height
Double Stacked
Height
Triple Stacked
80”
(2032 mm)
60 ¹/₂”
(1537 mm)
44 ¹/₈”
(1121 mm)
63 ³/₈”
(1610 mm)
66 ³/₈”
(1686 mm)
Model
Number
Agency
Utility
1600-000-U
NSF/CSA
Natural
1633-000-E
NSF/AGA/CE
Natural
Input Rate
110,000 BTU
32.2 kW
(116 MJ)
Voltage
Hertz
Phase
Supply
120
60
1
3
230
50
1
3
220
60
1
5
120
60
1
3
1635-V00-E
--
Natural
1601-000-U
NSF/CSA
LP
1634-000-E
NSF/AGA/CE
LP
230
50
1
3
1636-V00-E
--
LP
220
60
1
5
1621-000-E
CE
Electric
400/230
50
3
5
1622-000-U
UL/NSF
Electric
120/208
60
3
5
1623-000-U
UL/NSF
Electric
120/240
60
3
5
1624-000-U
UL/NSF
Electric
120/220
60
3
5
1628-000-N
--
Electric
29 kW
380/220
50
3
5
1629-000-N
--
Electric
415/240
50
3
5
1637-000-E
CE
Electric
215/240
50
3
5
NOTE: Panel setups are added as kit numbers to the end of the model number to complete the oven order; (example: 1600-000-U-K1819 is a 1600-000-U with
standard setup, left to right.)
Technical Drawings:
”
mm)
91”
11mm)
(19 mm)
UNION
120 VOLT
3/4” N.P.T.
10 FT. LONG
(19 mm)
POWER CORD
3/4” N.P.T. INLET w/Tee
(19 mm)
120 VOLT
10 FT. LONG
UNION
POWER CORD
GAS
3/4” N.P.T.
(19 mm)
GAS
(19 mm)
UNION
3/4” N.P.T.
(19 mm)
120 VOLT
10 FT. LONG
POWER CORD
GAS
3/4” N.P.T.
(19 mm)
GAS
UNION
120 VOLT
120 VOLT
3/4” N.P.T.
10 FT. LONG
10 FT. LONG
(19 mm)
POWER CORD
POWER CORD
3/4” N.P.T. INLET w/Tee
3/4” N.P.T. INLET w/Tee
GAS
UNION
Global
3/4” N.P.T. INLET w/Tee
(19 mm)
91”
(2311mm)
91”
(2311mm)
DOOR SWING
DOOR SWING
91”
(2311mm)
DOOR SWING
DOOR SWING
DOOR SWING
80” (2032 mm)
18”
(457 mm)
80” (2032 mm)
18”
(457 mm)
/2”
mm)
7 1/2”
91 mm)
m)
8”
mm)
40”
18”
(1016 mm)
(457 mm)
40” 18”
(1016
(457
mm)
mm)
80” (2032 mm)
22”
40”
(585 mm)
(1016 mm)
22”
(585 mm)
63 3/8”
(1610 mm)
80” (2032 mm)
22”40”
(585
(1016
mm)mm)
22”
(585 mm)
44 1/8”
(1121 mm)
32 1/8”
(816 mm)
7 1/2”
(191 mm)
18”
32 1/8”
(457 mm) (816 mm)
44 1/8”
(1121 mm)
40”
(1016 mm)
44 1/8”
(1121 mm)
32 1/8”
(816 mm)
32 1/8”
(816 mm)
51 3/8”
(1305 mm)
63 3/8”
(1610 mm)
22”
(585 mm)
7 1/2”
(191 mm)
32 1/8”
(816 mm)
32 1/8”
(816 mm)
44 1/8”
(1121 mm)
7 1/2”
(191 mm)
32 1/8”
(816 mm)
7 1/2”
(191 mm)
60 1/2”
(1537 mm)
60 1/2”
(1537 mm)
58 1/4”
(1479 mm)
66 3/8”
(1692 mm)
5 5/8”
(143 mm)
5 5/8”
(143 mm)
66 3/8”
(1692 mm)
54 3/8”
(1387 mm)
66 3/8”
(1692 mm)
66 3/8”
(1692 mm)
16”
(406 mm)
35 1/2”
(901 mm)
16”
(406 mm)
33 1/2”
(851 mm) 60 1/2”
OPENING(1537 mm)
58 1/4”
(1479 mm)
33
1/2”
3 1/8”
(851
mm)
(79 mm)
OPENING
3 1/8”
(79 mm)
OPENING
35 1/2”
54 3/8”
(901 mm)
(1387 mm)
16”
(406 mm)35 1/2”
(901 mm)
3 1/8” 66 3/8”
(79 mm)(1692 mm)
OPENING
3 1/8”
(79 mm)
OPENING
33 1/2”
(851 mm)
60 1/2”
OPENING
(1537 mm) 64 1/2”
(1638 mm)
58 1/4”
(1479 mm)
33 1/2”
(851 mm)
OPENING
GAS
64 1/2”
(1638 mm)
27 5/8”
GAS 64 1/2”
(1638 mm)
GAS(702 mm)
OPENING
16”
(406 mm)
64 1/2”
(1638 mm)
27 5/8”
GAS
(702 mm)
27 5/8” 3 1/8”
(702 mm) (79 mm)
35 1/2”
(901 mm)
5 5/8”
(143 mm)
58 1/4”
(1479 mm)
54 3/8”
(1387 mm)
16”
(406 mm)
NOTE: Specifications subject to change without notification.
32 1/8”
(816 mm)
51 3/8”
(1305 mm)
51 3/8”
(1305 mm)
7 1/2”
(191 mm)
35 1/2”
(901 mm) 54 3/8”
(1387 mm)
63 3/8”
(1610 mm)
32 1/8”
(816 mm)
7 1/2”
(191 mm)
7 1/2”
(191 mm)
7 1/2”
(191 mm)
54 3/8”
(1387 mm)
63 3/8”
(1610 mm)
51 3/8”
(1305 mm)
(2032 mm)
4480”
1/8”
(1121 mm)
1600 Series | Impinger® Low Profile Single Belt Conveyorized Oven
3/4” N.P.T. INLET w/Tee
(19 mm)
27 5/8”
(702 mm)
33 1
(851 m
OPEN