Download Lightolier IS:40616 User's Manual

READ AND UNDERSTAND
THESEINSTRUCTIONS
BEFORE
INSTALLINGFIXTUFIE
is intesdedfor installationin acznrdance with tha National Electrical Code and Ictal regulations.
assura full compliance witi local ccdas and regulations, thack with your Id electrical inspactor before
tallation. To prevent elmtricel shcck, turn off elwtrici~ at fuw box bafora proceeding.
INSTRUCTION SHEE
ISfwra
IS:40616
R0194
Retainthese irretrarctimra
for maintenancereference.
Page 10
INSTRUCTIONS FOR INSTALLATION OF A.D.A. TRIO FIXTURES.
COVERSFIXTURES 4tM16WH,4(K16WHE1,40616WHE2,4W16WHN1, 40616WHH1,40616WHN2,
40616sB, 4W16SBE1,40616SBE2,40616SBN1,4LW16SBH1,40616sBN2,
40616SC,40616SCEl, 40616SCE2,40616SCN1,40B16SCH1AND 40616SCN2
NOTE This instructionsheetcoversbothcompactfluorescentand incandescenttypafirrturea.Althoughilhretrati(
showscompactfhaorescantversion,the incandescentversionassamblesand installstha sama.
IACKPIATE INSTALLATION:
1. Loosan two MOUNTING
from LOWER MOUNTING
SCREWS in LOWER MOUNTING
BRACKFE
and ramove OIFFUSER ASSEMBLY
BRACKETS and unhooking ASSEMBLY from two UPPER MOUNTING
2. Thraad CROSSBAR MOUNTING
by pulling OIFFUSER ASSE
BRACKETS (Fig. 1, Fig. 2 and Fig. 3).
SCREWS into CROSSBAR as shown in Fig. 1.
3. Using appropriate slots in CROSSBAR, sacure CROSSBAR to OUTLETBOX using OUTLET BOX SCREWS (providad with OUTLET 60)
4. While supporting BACKPLATEmaka connations black fisture laad or fixtura Iaed without trmar marks to hot (black) supply Iaad; v
lead or fisture lead with tracar marks to nautral (white) supply Iced. Uninsulated fklura wire is a ground wire and must be connect,
grounding tarminal or connections back into OUTLET BOX.
5. Position BACKPU+TE over CROSSBAR allowing CROSSBAR MOUNTING SCREWS to coma through holas in BACKPLATE.
CAUTION: Make certain wires ara not pinched between parts.
6. SacureBACKPL4TE
byinstalling
two BA~ERYNUTSoverCROSSBAR
MOUNTINGSCREWSandtighten.
7. Installracommendad
lamp(s).
CAUTION
MAXIMUM WAITAGE AS MAFIKEDON FIXTUREMUST NOT BE EXCEEOEO.
o
CR
Sc
1-1
C3HTC>LIEl?’
:::+’:~f~
NSTRUCTIONStlE~ NO.
INSTRUCTIONS FOR INSTALLATION OF A.D.A. TRIO FIXTURES.
1S:40616
lM6t
COVERSFIXTURES 40616WH, 4M16WHE1, 4&16WHE2, 4tNi16WHNl, 4W16WHHI,
AW16WHN2, 4061.6SB,40616SBE1,.40616SBE2,
4LM16SBN1,40616SBH1,41W16SBN2,
4iW16SC,~6SGEl,
60616SCEZ4W16SCN1, 4Mi16SCHl ANO 4M16SCM
)
Page2012
●
)IFFUSERINSTAU.ATION
1. HookDIFFUSIR ASSEMG4Yover UPPER.MOUNTINGBRACKETSallowing UPPERMOUNTING SCREWSto go down into holes in UPPERMOUNTING
WIACKETS,swing OIFFUSERASSEMBLYagainst EACKFLATE(Fig.2).
2. Secure OIFFUSERASSEMBLYin positionbytighteningtwo LOWERMOUNTING SCREWSinto LOWERMOUNTING BRACKETS(Fig.3).
wvMOuNT’NG
/-
~
UFPERMOUNTING
iihACKET
R
-
●
DIFFUSER
ASSEMBLY
B
J
LOWER
MOUNTING
SCREW
LOWER
MOUNTING
BRAcKH
\
=
GACKFIATE
M.2
FIG.3
●