Download Harbor Freight Tools 12 in. Four Tray Revolving Storage Product manual

Specifications
Bins:
Tray Diameters:
Dividers:
2 Bottom Trays:
2 Top Trays:
Maximum Weight:
Weight:
Ball Bearing revolving bins
11-3/4" diameter x 1" deep
5-1/2" L x 3" H x 1/64" Thick
Three Divider Trays
Six Divider Trays
7-1/2 lb each Tray (evenly distributed); 30 lb total
6.4 lb
IMPORTANT SAFETY INFORMATION
Assembly Precautions
1. Assemble only according to these instructions.
Improper assembly can create hazards.
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the
influence of alcohol, drugs or medication.
6. Weight capacity and other product capabilities apply
to properly and completely assembled product only.
Use Precautions
1. This product is not a toy. Do not allow
children to play with or near this item.
2. Use as intended only.
5. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
3. Inspect before every use; do not use
if parts are loose or damaged.
6. Only locate the Revolving Bins on a clean, flat, level
surface. Be careful not to tip over the Revolving Bins.
4. Do not exceed listed weight capacity.
Be aware of dynamic loading!
Sudden load movement may briefly create
excess load causing product failure.
7. Warning: The warnings, cautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document
including all text under subheadings therein before set up or use of this product.
1. On your workbench or a clean, flat surface, lay
out all four Trays (1). There are two 6-hole Trays
and two 12-hole Trays. Locate and lay out the
two 6-Hole Shafts (4) and the two 12-Hole Shafts
(5). Locate and lay out all eighteen Dividers (3).
3. Lay one Divider over the base and line up
the holes in the bottom of the Divider with the
holes in the 6-Hole Tray (See Figure A).
6-Hole Tray (1)
2. Set one 6- Hole Shaft onto one 6-Hole Tray
with the base resting on the 6-Hole Tray.
6-Hole Shaft (4)
Item 94050
Bolt (11)
Figure A
For technical questions, please call 1-888-866-5797.
Page 2
4. Insert one Bolt (11) down through the Divider
and the Tray. From underneath slide on one
Small Flat Washer (12) and thread on Small
Hex Nut (13) (See Figure A and Figure B).
Divider
Shaft
Bolt
Flat Washer
8. Insert the Connector Tube (7) down
into the Center Tube top end.
9. Slide Trays onto the Center Tube separated
by a Large Flat Washer (9), Flat Ball Bearing
(10) and Large Flat Washer between each
Tray (see Figure D). From the Base up, you
will have one Flat Ball Bearing, then a Large
Flat Washer. Next one Tray, Large Flat Washer,
Flat Ball Bearing, and Large Flat Washer.
Small Hex Nut
6 Dividers
Figure B
5. Assemble all Dividers in the same manner.
Repeat for the second 6-Hole Tray.
Flat Ball
Bearing
Center Tube
3 Dividers
6. Follow the same steps for assembling
each of the 12-Hole Trays.
Base
7. Attach the Center Tube (6) to the Base (2)
using three M6 x 10mm Bolts (14). Slide
on Medium Flat Washer (15) and thread on
Medium Hex Nut (16) (see Figure C).
Figure D
10. Repeat until all four Trays are installed.
11. Screw the Handle Screw (8) down onto the
welded Nut on the end of the Center Tube.
Tighten the Handle Screw securely.
Center Tube
12. Make certain all hardware is secure and fully
tightened. Turn the Trays to make certain that
they rotate smoothly and evenly. Verify that the
Base and Trays sit properly on a flat surface.
M6x10 Bolt
Medium Flat
Washer
Large Flat
Washer
Base
13. Use the Revolving Bins with 12" Diameter Trays only
on a flat, level surface capable of supporting the
Revolving Bins and the weight of everything in the
Trays. Always distribute the weight evenly among the
bins. Heavier weights should be in the lower bins.
Medium
Hex Nut
Figure C
Parts List and Diagram
Part
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Description
Tray (two 6-Hole and two 12-Hole)
Base
Divider
6-Hole Shaft
12-Hole Shaft
Center Tube
Connector Tube
Handle Screw
Large Flat Washer
Flat Ball Bearing
M5x8mm Bolt
Small Flat Washer
Small Hex Nut
M6 x 10mm Bolt
Medium Flat Washer
Medium Hex Nut
Item 94050
Qty.
4
1
18
2
2
1
1
1
7
4
72
72
72
3
3
3
1
2
12pc Holes
6pc Holes
4
3
9
5
10
11
12 13
14
15 16
7
6
For technical questions, please call 1-888-866-5797.
8
Page 3
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Some parts are listed and shown for
illustration purposes only, and are not available
individually as replacement parts.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Item 94050
For technical questions, please call 1-888-866-5797.
Page 4