Download Fujitsu FPC58-0437-02 User's Manual

Copyright
Copyright
Earthlink is a registered trademark of EarthLink
Network, Inc.
Fujitsu PC Corporation has made every effort to ensure
the accuracy and completeness of this document.
However, as ongoing development efforts are continually
improving the capabilities of our products, we cannot
guarantee the accuracy of the contents of this document.
We disclaim liability for errors, omissions, or future
changes.
Netscape Communicator is a registered trademark of
Netscape Communications Corporation.
Fujitsu and the Fujitsu logo are registered trademarks
and LifeBook is a trademark of Fujitsu Limited.
All other trademarks mentioned herein are the property
of their respective owners.
PC-Doctor is a trademark of PC-Doctor.com, Inc.
LapLink is a registered trademark of LapLink.com, Inc.
McAfee is a registered trademark of Network Associates/
McAfee.com, Inc.
First Cabin is a servicemark of Fujitsu PC Corporation.
The following are registered trademarks of Microsoft
Corporation: MS, MS-DOS, Windows.
PCMCIA is a trademark of the Personal Computer
Memory Card International Association.
Intel and Celeron are registered trademarks of Intel
Corporation.
Adobe Acrobat Reader is a registered trademark of
Adobe System Inc.
CompuServe and AOL are registered trademarks of
America Online, Inc.
© Copyright 2000 Fujitsu PC Corporation. All rights
reserved. No part of this publication may be copied,
reproduced, or translated, without prior written consent
of Fujitsu PC Corporation. No part of this publication
may be stored or transmitted in any electronic form
without the written consent of Fujitsu PC Corporation.
FPC58-0437-02
B5FH-2031-02EN-00
DECLARATION OF CONFORMITY
according to FCC Part 15
Responsible Party Name:
Fujitsu PC Corporation
Address:
5200 Patrick Henry Drive
Santa Clara, CA 95054
Telephone:
(408) 982-9500
Declares that product:
Model Configuration:
LifeBook B-2175
Complies with Part 15 of the FCC Rules.
This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions:
(1) This device must not be allowed to cause harmful interference, (2) This device must accept any
interference received, including interference that may cause undesired operation.
LifeBook B Series
CAUTION
Changes or modifications not expressly approved by
Fujitsu PC Corporation could void this user’s authority
to operate the equipment.
FCC NOTICES
Notice to Users of Radios and Television
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
■
■
■
■
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet that is on a
different circuit than the receiver.
Consult the dealer or an experienced radio/TV
technician for help.
Shielded interconnect cables must be employed with this
equipment to ensure compliance with the pertinent RF
emission limits governing this device.
Notice to Users of the US Telephone Network
Your Fujitsu LifeBook may be supplied with an internal
modem which complies with Part 68 of the FCC rules.
On this LifeBook is a label that contains the FCC Registration Number and the Ringer Equivalence Number
(REN) for this equipment among other information. If
requested, the user must provide their telephone
company with the following information:
1. The telephone number to which the LifeBook
is connected.
2. The Ringer Equivalence Number (REN) for
this equipment.
3. That the equipment requires a standard modular
jack type USOC RJ-11C which is FCC Part 68
compliant.
4. The FCC Registration Number.
This equipment is designed to be connected to the telephone network or premises wiring using a standard
modular jack type USOC RJ-11C which is FCC Part 68
compliant and a line cord between the modem and the
telephone network with a minimum of 26AWG.
The REN is used to determine the number of devices
that you may connect to your telephone line and still
have all of those devices ring when your number is
called. Too many devices on one line may result in
failure to ring in response to an incoming call. In most,
but not all, areas the sum of the RENs of all of the
devices should not exceed five (5). To be certain of
the number of devices you may connect to your line,
as determined by the RENs, contact your local
telephone company.
If this equipment causes harm to the telephone network,
your telephone company may discontinue your service
temporarily. If possible, they will notify you in advance.
If advance notice is not practical they will notify you as
soon as possible. You will also be advised of your right to
file a complaint with the FCC.
This fax modem also complies with fax branding
requirements per FCC Part 68.
Your telephone company will probably ask you to
disconnect this equipment from the telephone network
until the problem is corrected and you are sure that the
equipment is not malfunctioning. This equipment may
not be used on coin-operated telephones provided by
your telephone company. Connection to party lines is
subject to state tariffs. Contact your state’s public utility
commission, public service commission or corporation
commission for more information.
This equipment includes automatic dialing capability.
When programming and/or making test calls to
emergency numbers:
■
■
Remain on the line and briefly explain to the
dispatcher the reason for the call.
Perform such activities in off-peak hours, such
as early morning or late evening.
FCC rules prohibit the use of non-hearing aid compatible
telephones in the following locations or applications:
■
■
■
■
■
■
■
■
■
All public or semipublic coin-operated or credit
card telephones.
Elevators, highways, tunnels (automobile, subway,
railroad or pedestrian) where a person with impaired
hearing might be isolated in an emergency.
Places where telephones are specifically installed to
alert emergency authorities such as fire, police or
medical assistance personnel.
Hospital rooms, residential health care facilities,
convalescent homes and prisons.
Workstations for the hearing impaired.
Hotel, motel or apartment lobbies.
Stores where telephones are used by patrons to
order merchandise.
Public transportation terminals where telephones are
used to call taxis or to reserve lodging or rental cars.
In hotel and motel rooms as at least ten percent of
the rooms must contain hearing aid compatible telephones or jacks for plug-in hearing aid compatible
telephones which will be provided to hearing impaired
customers on request.
Copyright
DOC (INDUSTRY CANADA) NOTICES
Notice to Users of Radios and Television
This Class B digital apparatus meets all
requirements of the Canadian InterferenceCausing Equipment Regulations.
CET appareil numérique de la class B respecte toutes les
exigence du Réglement sur le matérial brouilleur du
Canada.
Notice to Users of the Canadian Telephone
Network
The Canadian Industry Canada label identifies certified
equipment. This certification means that the equipment
meets certain telecommunications network protective,
operational, and safety requirements. The Department
does not guarantee the equipment will operate to the
user’s satisfaction.
Fujitsu LifeBook computers are supplied with an
internal modem which complies with the Industry
Canada certification standards for telecommunication
network protection and safety requirements. Before
connecting this equipment to a telephone line the user
should ensure that it is permissible to connect this
equipment to the local telecommunication facilities.
The user should be aware that compliance with the
certification standards does not prevent service
degradation in some situations.
Repairs to telecommunication equipment should be
made by a Canadian authorized maintenance facility.
Any repairs or alterations not expressly approved by
Fujitsu PC Corporation or any equipment failures
may give the telecommunication company cause to
request the user to disconnect the equipment from
the telephone line.
The connecting arrangement code for this equipment
is CA11A.
The Load Number assigned to each telephone terminal
device denotes the percentage of the total load to be
connected to a telephone loop or circuit which is used
by the device to prevent overloading. The termination
on a loop may consist of any combination of devices
such that the total of the load numbers of all devices
does not exceed 100.
CAUTION
For safety, users should ensure that the electrical
ground of the power utility, the telephone lines and
the metallic water pipes are connected together.
Users should NOT attempt to make such connections
themselves but should contact the appropriate electric
inspection authority or electrician. This may be
particularly important in rural areas.
Avis Aux Utilisateurs Du Réseau
Téléphonique Canadien
L’étiquette canadienne Industrie Canada identifie
l’équipement certifié. Cette certification signifie que
l’équipement satisfait certaines normes de protection,
d’exploitation et de sécurité des réseaux de télécommunications. Le département ne garantit pas le fonctionnement de l’équipement à la satisfaction de l’utilisateur.
La série LifeBookTM e possède un modem interne
conforme aux normes de certification d’Industrie
Canada pour protéger les réseaux de télécommunications et satisfaire aux normes de sécurité. Avant de
connecter cet équipement à une ligne téléphonique,
l’utilisateur doit vérifier s’il est permis de connecter cet
équipement aux installations de télécommunications
locales. L’utilisateur est averti que même la conformité
aux normes de certification ne peut dans certains cas
empêcher la dégradation du service.
Les réparations de l’équipement de télécommunications
doivent être eVectuées par un service de maintenance
agréé au Canada. Toute réparation ou modification, qui
n’est pas expressément approuvée par Fujitsu PC
Corporation, ou toute défaillance de l’équipement peut
entraîner la compagnie de télécommunications à exiger
que l’utilisateur déconnecte l’équipement de la ligne
téléphonique.
Le code d’arrangement de connexion de cet équipement
est CA11A.
Le numéro de charge assigné à chaque terminal téléphonique indique le pourcentage de la charge totale pouvant
être connecté à une boucle ou à un circuit téléphonique,
utilisé par ce périphérique afin de prévenir toute
surcharge. La terminaison d’une boucle peut être constituée de n’importe quelle combinaison de périphériques
de sorte que le total de numéros de charge de tous les
périphériques n’excède pas 100.
AV E RT I S S E M E N T
Pour assurer la sécurité, les utilisateurs doivent vérifier
que la prise de terre du service d’électricité, les lignes
télphoniques et les conduites d’eau métalliques sont
connectées ensemble. Les utilisateurs NE doivent PAS
tenter d’établir ces connexions eux-mêmes, mais
doivent contacter les services d’inspection d’installations
électriques appropriés ou un électricien. Ceci peut être
particulièrement important en régions rurales.
LifeBook B Series
UL Notice
This unit requires an AC adapter to operate. Use only UL
Listed Class 2 Adapters with an output rating of 16Vdc,
with a current of 2.5A.
AC Adapter output polarity:
+
CAUTION
To reduce the risk of fire, use only #26 AWG or larger
telecommunications line cord.
For Authorized Repair Technicians Only
CAUTION
For continued protection against risk of fire, replace
only with the same type and rating fuse.
CAUTION
Danger of explosion if Lithium (clock) battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instruction.
Ta b l e o f C o n t e n t s
Fujitsu LifeBook B Series Notebook
Table of Contents
1
PREFACE
Preface
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . 3
Fujitsu PC Contact Information. . . . . . . . . . . . . . . 3
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
GETTING TO KNOW
YOUR LIFEBOOK
Overview
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Locating the Controls
and Connectors
Top and Front Components . . . . . . . . . . . . . . . . . 8
Left-Side Panel Components . . . . . . . . . . . . . . . 10
Right-Side Panel Components . . . . . . . . . . . . . . 11
Bottom Components . . . . . . . . . . . . . . . . . . . . . 12
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . .15
Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Function Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Quick Point Pointing Device
Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Volume Control
Controlling the Volume . . . . . . . . . . . . . . . . . . . 20
LifeBook Security/Application Panel
Setting up Your LifeBook Security Panel . . . . . . .21
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Operating Your LifeBook Security/
Application Panel . . . . . . . . . . . . . . . . . . . . . . . . 22
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Uninstalling the Security Panel Application . . . . . 22
Launching Applications with
the Security/Application Panel . . . . . . . . . . . . . 23
3
GETTING STARTED
Power Sources
Status Indicator Panel
Connecting the Power Adapters . . . . . . . . . . . . . 27
Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . 13
AC Adapter Indicator . . . . . . . . . . . . . . . . . . . . . 13
Battery Level Indicators . . . . . . . . . . . . . . . . . . . 13
Battery Charging Indicators . . . . . . . . . . . . . . . . 14
Hard Drive or Removable
Media Drive Access Indicator . . . . . . . . . . . . . . 14
PC Card Access Indicators . . . . . . . . . . . . . . . . . 14
NumLk Indicator. . . . . . . . . . . . . . . . . . . . . . . . . 14
CapsLock Indicator . . . . . . . . . . . . . . . . . . . . . . . 14
ScrLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Security Indicator. . . . . . . . . . . . . . . . . . . . . . . . 14
Display Panel
Keyboard
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . 15
Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . . 15
Opening the Display Panel . . . . . . . . . . . . . . . . . 28
Adjusting Display Panel Brightness . . . . . . . . . . . 28
Closing the Display Panel . . . . . . . . . . . . . . . . . .28
Starting Your LifeBook
Power On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . 29
BIOS Setup Utility. . . . . . . . . . . . . . . . . . . . . . . . 29
Booting the System
with Windows 98 Second Edition . . . . . . . . . . . 30
Installing Click Me! (Windows 98 only) . . . . . . . 31
Booting the System with
Windows 2000 Professional . . . . . . . . . . . . . . .31
Registering Your LifeBook . . . . . . . . . . . . . . . . . 31
!
LifeBook i Series
Power Management
Detaching the Port Replicator . . . . . . . . . . . . . . 45
Suspend/Resume Button . . . . . . . . . . . . . . . . . . 32
Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Save-to-Disk Mode
(Windows 98 Second Edition models only) . . . . 32
Hibernation Feature
(Windows 2000 Professional models only) . . . . 33
Idle Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . 34
Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . 34
Windows Power Management . . . . . . . . . . . . . . 34
Restarting the System. . . . . . . . . . . . . . . . . . . . . 34
Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Device Ports
4
USER-INSTALLABLE FEATURES
Lithium ion Battery
Recharging the Batteries. . . . . . . . . . . . . . . . . . . 37
Replacing the Battery . . . . . . . . . . . . . . . . . . . . . 38
External Floppy Disk Drive
Loading a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Ejecting a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Preparing a Disk for Use. . . . . . . . . . . . . . . . . . . 39
PC Cards
Modem (RJ-11) Telephone Port . . . . . . . . . . . . . 46
Internal LAN (RJ-45) Port. . . . . . . . . . . . . . . . . . 46
Parallel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
PS/2 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
External Floppy Disk Drive Port . . . . . . . . . . . . . 47
Universal Serial Bus Port. . . . . . . . . . . . . . . . . . . 47
Infrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 47
Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 47
External Monitor Port . . . . . . . . . . . . . . . . . . . . 47
5
TROUBLESHOOTING
Troubleshooting
Identifying the Problem . . . . . . . . . . . . . . . . . . . 51
Specific Problems . . . . . . . . . . . . . . . . . . . . . . . . 51
Troubleshooting Table . . . . . . . . . . . . . . . . . . . . 52
Power On Self Test Messages . . . . . . . . . . . . . . 61
Modem Result Codes. . . . . . . . . . . . . . . . . . . . . 62
Restoring Your
Pre-installed Software
Installing PC Cards . . . . . . . . . . . . . . . . . . . . . . . 40
Removing PC Cards . . . . . . . . . . . . . . . . . . . . . . 40
SmartCard Reader . . . . . . . . . . . . . . . . . . . . . . . 41
Drive Image Special Edition (DISE) . . . . . . . . . . . 63
Drivers and Applications Restore CD . . . . . . . . . 63
Memory Upgrade Module
6
Installing a Memory Upgrade Module . . . . . . . . 42
Removing a Memory Upgrade Module . . . . . . . 42
Checking the Computer Recognition
of New Memory Capacity . . . . . . . . . . . . . . . . 43
Port Replicator
Rear Panel Components . . . . . . . . . . . . . . . . . . . 44
Front Panel Components . . . . . . . . . . . . . . . . . . 45
Attaching the Port Replicator . . . . . . . . . . . . . . . 45
CARE AND MAINTENANCE
Care and Maintenance
LifeBook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Floppy Disks and Drives . . . . . . . . . . . . . . . . . . . 68
CDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
"
Ta b l e o f C o n t e n t s
7
SPECIFICATIONS
Specifications
Configuration Label . . . . . . . . . . . . . . . . . . . . . . 73
Microprocessor. . . . . . . . . . . . . . . . . . . . . . . . . . 73
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Mass Storage Device Options. . . . . . . . . . . . . . . 73
Integrated Pointing Device . . . . . . . . . . . . . . . . . 73
LifeBook Security/Application Panel . . . . . . . . . . 73
Theft Prevention Lock . . . . . . . . . . . . . . . . . . . . 74
Communications . . . . . . . . . . . . . . . . . . . . . . . . 74
Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Dimensions and Weight . . . . . . . . . . . . . . . . . . . 74
Environmental Requirements . . . . . . . . . . . . . . .75
Popular Accessories . . . . . . . . . . . . . . . . . . . . . . 75
Pre-Installed Software . . . . . . . . . . . . . . . . . . . . 75
Learning About Your Application Software. . . . . 75
8
GLOSSARY
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
#
LifeBook i Series
1
Preface
1
LifeBook B Series
2
Preface
Preface
ABOUT THIS GUIDE
The LifeBook™ B Series notebook from Fujitsu PC
Corporation is a powerful mini-notebook computer. It
is powered by an Intel® Celeron™ microprocessor,
has a built-in color touch screen display, and brings the
computing power of desktop personal computers (PCs)
to a portable environment.
This manual explains how to operate your LifeBook’s
hardware and built-in system software. Your LifeBook is
compatible with the IBM® PC AT.
FUJITSU PC CONTACT INFORMATION
Service and Support
You can contact Fujitsu Service and Support the
following ways:
■
■
■
■
Before you place the call, you should have the
following information ready so that the customer
support representative can provide you with the
fastest possible solution:
■
It comes with Windows® 98 Second Edition or
Windows® 2000 Professional pre-installed.
Your LifeBook is a completely self-contained unit with
an active-matrix (TFT) color LCD display. It has a
powerful interface that enables it to support a variety of
optional features.
■
■
■
■
■
■
■
Conventions Used in the Guide
Keyboard keys appear in brackets.
Example: [Fn], [F1], [Esc], [Enter] and [Ctrl].
Pages with additional information about a specific topic
are cross-referenced within the text.
Example: (See page xx.)
On screen buttons or menu items appear in bold
Example: Click OK to restart your LifeBook.
DOS commands you enter appear in Courier type.
Example: Shutdown the computer?
Toll free: 1-800-8FUJITSU (1-800-838-5487)
Fax: 1-901-259-5700
E-mail: [email protected]
Web site: http://www.fujitsupc.com
Product name
Product configuration number
Product serial number
Purchase date
Conditions under which the problem occurred
Any error messages that have occurred
Hardware configuration
Type of device connected, if any
Fujitsu On-line
You can go directly to the on-line Fujitsu Product
catalog for your LifeBook by clicking on the LifeBook
Accessories Web site URL link, located in the Windows
Start menu.
You can also reach Fujitsu Service and Support on-line
by clicking on the Fujitsu Service and Support Web site
URL link, located in the Service and Support Software
folder of the Windows Start menu.
POINT
POINT
The point icon highlights information that will enhance
your understanding of the subject material.
CAUTION
The caution icon highlights information that is
important to your safety, to the safe operation of your
computer, or to the integrity of your files. Please read
all caution information carefully.
You must have an active internet connection to use the
on-line URL links.
WARRANTY
Your LifeBook is backed by a one year International
Limited Warranty and includes toll-free technical
support. Check the service kit that came with your
LifeBook for warranty terms and conditions.
WARNING
The warning icon highlights information that can be
hazardous to either you, your LifeBook, or your files.
Please read all warning information carefully.
3
LifeBook B Series – Section One
4
2
Getting to Know
Your LifeBook
5
!
LifeBook B Series – Section Two
6
"
G e t t i n g t o K n o w Yo u r L i f e B o o k
Figure 2-1 Fujitsu LifeBook B Series
Overview
This section describes the components of your Fujitsu
LifeBook B Series notebook. We strongly recommend
that you read it before using your LifeBook – even if you
are already familiar with notebook computers.
UNPACKING
When you receive your LifeBook, unpack it carefully,
and compare the parts you have received with the items
listed below.
Figure 2-2 AC Adapter
For a pre-configured model you should have:
■
■
■
■
■
■
■
■
■
■
■
■
LifeBook B-Series notebook (Figure 2-1)
Two 3-cell Lithium ion batteries (one pre-installed)
AC adapter with AC power cord (Figure 2-2)
Port Replicator (Figure 2-3)
External USB Floppy Disk Drive (Figure 2-4)
Phone/Modem (RJ-11) telephone cable
Driver and Application Restore CD
Getting Started Guide
User’s Guide (this document)
International Limited Warranty Brochure
Microsoft Windows Manual and
Certificate of Authenticity
First Cabin Registration card and envelope
Figure 2-3 Port Replicator
Figure 2-4 External Floppy Disk Drive
7
#
LifeBook B Series – Section Two
Display Panel Latch
Touch Screen Stylus
Suspend/Resume Button
Display Panel
Status Indicator Panel
Closed Cover Switch
Cursor Control
LifeBook Security/
Application Panel
Keyboard
Quick Point
Pointing Device
Built-in
Microphone
Figure 2-5 LifeBook with display open
Locating the Controls
and Connectors
Status Indicator Panel
The Status Indicator Panel displays symbols that correspond with a specific component of your LifeBook.
(Figure 2-5) See “Status Indicator Panel” on page 13.
TOP AND FRONT COMPONENTS
Display Panel Latch
The display panel latch locks and releases the display
panel. (Figure 2-5)
The following is a brief description of your LifeBook’s
top and front components.
Touch Screen Stylus
The stylus is used as the pointing device for the touch
screen. (Figure 2-5)
Closed Cover Switch
The closed cover switch turns off the LCD back
lighting when the display panel is closed. (Figure 2-5)
Suspend/Resume Button
The Suspend/Resume button allows you to suspend LifeBook activity without powering off, resume your LifeBook from suspend mode, and power on your LifeBook
when it has been shut down from the Windows operating system. (Figure 2-5) See “Suspend/Resume
Button” on page 32.
8
LifeBook Security/Application Panel
The LifeBook Security/Application Panel provides
hardware security and one-touch application launch
capability. (Figure 2-5) See “LifeBook Security/Application Panel” on page 23.
Quick Point Pointing Device
The Quick Point pointing device consists of two mouselike buttons and one cursor control button. (Figure 2-5)
See “Quick Point Pointing Device” on page 17.
Keyboard
A full-function keyboard with dedicated Windows
keys. (Figure 2-5) See “Keyboard” on page 15.
G e t t i n g t o K n o w Yo u r L i f e B o o k
Built-in Microphone
The built-in microphone allows mono audio input.
(Figure 2-5)
Display Panel
The display panel is a color LCD panel with back
lighting for the display of text and graphics and Touch
Screen functionality. (Figure 2-5)
9
LifeBook B Series – Section Two
DC Power Jack
Air Vents
External Monitor Port
(behind cover)
Figure 2-6 LifeBook left-side panel
LEFT-SIDE PANEL COMPONENTS
Following is a brief description of your LifeBook’s
left-side components.
DC Power Jack
The DC power jack allows you to plug in the AC adapter
or the optional Auto/Airline adapter to power your LifeBook and charge the internal Lithium ion Battery.
(Figure 2-6)
10
PC Card Slot
PC Card Eject/Lock Button
External Monitor Port
The external monitor port allows you to connect an
external VGA or SVGA CRT monitor. Note that when
the Port Replicator is attached to the system, you must
use the external monitor port on the Port Replicator
rather than the port on the system. (Figure 2-7) See
“External Monitor Port” on page 47.
PC Card Slot
The PC Card Slot allow you to install two Type II or
one Type III PC Card. (Figure 2-6) See “PC Cards” on
page 40.
G e t t i n g t o K n o w Yo u r L i f e B o o k
Infrared Port
Microphone Jack
LAN (RJ-45) Port
USB Ports
Power Switch
Headphone Jack
Modem (RJ-11) Port
Anti-theft Lock
Figure 2-7 LifeBook right-side panel
RIGHT-SIDE PANEL COMPONENTS
Following is a brief description of your LifeBook’s
right-side components.
Headphone Jack
The headphone jack allows you to connect headphones
or powered external speakers. (Figure 2-7) See “Headphone Jack” on page 47.
Microphone Jack
The microphone jack allows you to connect an external
mono microphone. (Figure 2-7) See “Microphone Jack”
on page 47.
Power Switch
This switch is the main power switch for your LifeBook.
(Figure 2-7)
USB Ports
The two USB ports allow you to connect Universal Serial
Bus devices. (Figure 2-7) See “Universal Serial Bus Port”
on page 47.
Infrared Port
The fast IrDA compatible port allows you to communicate with another IrDA compatible infrared device
without a cable. (Figure 2-6)
Modem (RJ-11) Telephone Port
The Modem (RJ-11) telephone port is for attaching
a telephone line to the internal multinational 56K
modem. (Figure 2-6)
WARNING
The internal multinational modem is not intended for
use with Digital PBX systems. Do not connect the
internal modem to a Digital PBX as it may cause serious
damage to the internal modem or your entire LifeBook.
Consult your PBX manufacturer’s documentation for
details. Some hotels have Digital PBX systems. Be sure
to find out BEFORE you connect your modem.
POINT
The internal modem is designed to the ITU-T V.90
standard. Its maximum speed of 53000bps is the
highest allowed by FCC, and its actual connection
rate depends on the line conditions. The maximum
speed is 33600bps at upload.
LAN (RJ-45) Port
The internal LAN (RJ-45) port is used for an internal
Fast Ethernet (10/100 Base-T/Tx) connection.
(Figure 2-6) See “Internal LAN (RJ-45) Port” on
page 46.
Anti-theft Lock Slot
The anti-theft lock slot allows you to attach a optional
physical lock down device. (Figure 2-7)
11
LifeBook B Series – Section Two
Battery Pack Lock
Battery Pack Latch
Lithium ion
Battery Bay
Port Replicator
Connector
Main Unit and
Configuration
Label (approximate
location)
Memory Upgrade
Compartment
Speaker
Speaker
Figure 2-8 LifeBook bottom panel
BOTTOM COMPONENTS
Following is a brief description of your LifeBook’s
bottom panel components.
Lithium ion Battery Bay
The battery bay contains the internal Lithium ion
battery. It can be opened for the removal of the battery
when stored over a long period of time or for swapping
a discharged battery with a charged Lithium ion battery.
(Figure 2-8) See “Lithium ion Battery” on page 37.
Stereo Speakers
The built-in dual speakers allow for stereo sound.
(Figure 2-8)
Port Replicator Connector
This connector allows you to connect the Port Replicator. (Figure 2-8)
12
Main Unit and Configuration Label
The configuration label shows the model number and
other information about your LifeBook. In addition,
the configuration portion of the label has the serial
number and manufacturer information that you will
need to give your support representative. It identifies the
exact version of various components of your LifeBook.
(Figure 2-8)
Memory Upgrade Compartment
Your LifeBook comes with high speed Synchronous
Dynamic RAM (SDRAM). The memory upgrade
compartment allows you to expand the system memory
capacity of your LifeBook, hence improving overall
performance. (Figure 2-8) See “Memory Upgrade
Module” on page 42.
G e t t i n g t o K n o w Yo u r L i f e B o o k
Battery
Charging
1
Hard Drive
Access
AC Adapter
2
PC Card
Access
Battery
Level
1
A
Security
Indicator
CapsLk
NumLk
Power
ScrLk
Figure 2-9 Status Indicator Panel
Status Indicator Panel
The Status Indicator displays symbols that correspond
with a specific component of your LifeBook. These
symbols tell you how each of those components are
operating. (Figure 2-9)
POWER INDICATOR
The Power indicator symbol states whether your
system is operational. It has several different states,
each of which tells you what mode your LifeBook is
in at that time.
■
■
■
Steady On: This means that there is power to your
LifeBook and that it is ready for use.
Flashing: This means that your LifeBook is in
Suspend mode.
Steady Off: This means that your system is either in
Save-to-Disk mode, or that your LifeBook has been
turned off with the power switch.
If you are charging your battery, the Power indicator
symbol will remain on even if your LifeBook is shut off.
The Power indicator symbol will also remain on if you
have either adapter connected and are shut down from
Windows, but have not turned off the power switch.
AC ADAPTER INDICATOR
The AC Adapter indicator states whether your LifeBook
is operating from the AC adapter, the Auto/Airline
adapter or the batteries. This icon has two different
states that can tell you what power source your LifeBook
is using.
■
■
On: This means that either of the adapters are
currently in use.
Off: Power is only coming from the batteries, and
you do not have an adapter connected.
BATTERY LEVEL INDICATORS
The Battery Level indicators state whether or not the
primary Lithium ion battery is installed. In addition,
this symbol states how much charge is available within
the installed battery. The symbol will only be displayed
for a battery that is currently installed in your LifeBook.
(Figure 2-10)
76%–100% Charging
76%–100%
51%–75%
26%–50%
11%–25%
Low Warning <11%
Critical Low or
Dead Battery
Shorted Battery
Figure 2-10 Battery Level Indicator
13
LifeBook B Series – Section Two
1
CAUTION
A shorted battery is damaged and must be replaced.
(Figure 2-10)
2
PC CARD ACCESS INDICATORS
The PC Card Access indicator states whether or not your
LifeBook is accessing a PC Card. The indicator will flash
if your software tries to access a PC Card even if there is
no card installed. See “PC Cards” on page 40.
POINT
If there is no battery activity, the power adapters are not
connected, and the power switch is Off, the Battery
Level indicators will also be off.
BATTERY CHARGING INDICATORS
Located to the left of the Battery Level indicator is a
small arrow symbol. This symbol states whether the
battery is charging. This indicator operates whether the
power switch is in the On or Off position, and will flash
if the battery is too hot or cold to charge.
CAUTION
Batteries subjected to shocks, vibration or extreme
temperatures can be permanently damaged.
NUMLK INDICATOR
The NumLk indicator states that the internal keyboard is
set in ten-key numeric keypad mode.
POINT
If you are using the optional external numerical keypad,
pressing the [NumLk] key will activate the external
keypad. The indicator will come on, however it will not
change any of the functionality of your keyboard keys.
CAPSLOCK INDICATOR
The CapsLock indicator states that your keyboard is set
to type in all capital letters.
SCRLK INDICATOR
HARD DRIVE OR REMOVABLE
MEDIA DRIVE ACCESS INDICATOR
The Hard Drive Access indicator states whether your
internal hard drive.
The ScrLk indicator states that your scroll lock is active.
SECURITY INDICATOR
The Security Indicator flashes (if a password was set)
when the system resumes from Off or Suspend modes.
You must enter the password that was set in the Security
Panel before your system will resume operation.
14
G e t t i n g t o K n o w Yo u r L i f e B o o k
Function Keys
Back
Space
Tab
Fn Key
Start Key
Start Key
Numeric Keypad
Application Key
Cursor Keys
Figure 2-11 Keyboard
Keyboard
USING THE KEYBOARD
Your LifeBook has an integral 83-key keyboard. The keys
perform all the standard functions of a 101-key
keyboard, including the Windows keys and other special
function keys. This section describes the following keys.
(Figure 2-11)
■
■
■
■
Numeric keypad: Your LifeBook allows certain keys to
serve dual purposes, both as standard characters and
as numeric and mathematical keys. The ability to
toggle between the standard character and numerical
keys is controlled through the [NumLk] key.
Cursor keys: Your keyboard contains four arrow
keys for moving the cursor or insertion point to the
right, left, up, or down within windows, applications
and documents.
Function keys: The keys labeled [F1] through [F12],
are used in conjunction with the n][Fn] key to produce special actions that vary depending on what program is running.
Windows keys: These keys work with your Windows
operating system and function the same as the
onscreen Start menu button, or the right button on
your pointing device.
NUMERIC KEYPAD
Certain keys on the keyboard perform dual functions as
both standard character keys and numeric keypad keys.
NumLk can be activated by pressing the [NumLk] keys.
Turning off the NumLk feature is done the same way.
Once this feature is activated you can enter numerals 0
through 9, perform addition ( + ), subtraction ( - ),
multiplication ( * ), or division ( / ), and enter decimal
points ( . ) using the keys designated as ten-key function
keys. The keys in the numeric keypad are marked on the
front edge of the key to indicate their secondary functions. (Figure 2-11)
POINT
If you are using the optional external numerical keypad,
pressing the [NumLk] key will activate the external
keypad. The indicator will come on, however it will not
change any of the functionality of your keyboard keys.
WINDOWS KEYS
Your LifeBook has three Windows keys: two Start keys
and an Application key. The two Start keys display the
Start menu. This button functions the same as your
onscreen Start menu button. The Application key functions the same as your right mouse button and displays
shortcut menus for the selected item. (Please refer to
your Windows documentation for additional information regarding the Windows keys.) (Figure 2-11)
CURSOR KEYS
The cursor keys are the four arrow keys on the keyboard
which allow you to move the cursor up, down, left and
right in applications. In programs such as Windows
Explorer, it moves the “focus” (selects the next item up,
down, left, or right). (Figure 2-11)
15
!
LifeBook B Series – Section Two
FUNCTION KEYS
Your LifeBook has 12 function keys, F1 through F12.
The functions assigned to these keys differ for each
application. You should refer to your software documentation to find out how these keys are used.
(Figure 2-11)
[Fn] Key
The [Fn] key provides extended functions for the
LifeBook and is always used in conjunction with another
key.
■
[FN+F3]: Pressing [F3] while holding [FN] will toggle
the Audio Mute on and off.
■
[FN+F4]: Pressing [F4] while holding [FN] will toggle
the internal pointing device on and off.
■
[Fn +F5]: Pressing [F5] while holding [Fn] allows
you to toggle between video compensation and no
compensation. (Video compensation controls spacing
on the display. When it is enabled, displays with less
than 1024 x 768 or 800 x 600 pixel resolution will still
cover the entire screen.)
■
[Fn+F6]: Pressing [F6] repeatedly while holding [Fn]
will lower the brightness of your display.
■
[Fn+F7]: Pressing [F7] repeatedly while holding [Fn]
will increase the brightness of the display.
■
[FN+F8]: Pressing [F8] repeatedly while holding [FN]
will decrease the volume of your LifeBook.
■
[FN+F9]: Pressing [F9] repeatedly while holding [FN]
will increase the volume of your LifeBook.
■
[Fn+F10]: Pressing [F10] while holding [Fn] allows
you to change your selection of where to send your
display video. Each time you press the combination
of keys you will step to the next choice. The choices,
in order, are: built-in display panel only, both built-in
display panel and external monitor or external monitor only.
16
"
G e t t i n g t o K n o w Yo u r L i f e B o o k
Left Button
Right Button
Cursor Control
Figure 2-12 Quick Point pointing device
Quick Point Pointing
Device
The Quick Point is built into your LifeBook. It is used to
control the movement of the cursor to select items on
your display panel. The Quick Point is composed of a
cursor control at the center of the keyboard and two
buttons on the palm rest of your LifeBook. The cursor
control works the same way a mouse ball does, and
moves the cursor around the display. It only requires
light pressure with the tip of your finger, and the more
pressure you use, the faster the cursor will move. The
upper button functions the same as a left mouse button
while the lower button has the same function as a right
mouse button. The actual functionality of the buttons
may vary depending on the application that is being
used. (Figure 2-12)
Figure 2-13 Clicking
Double-Clicking
Double-clicking means pushing and releasing the top
button twice in rapid succession. This procedure does
not function with the right button. To double-click,
move the cursor to the item you wish to select, press
and release the top button twice. (Figure 2-14)
POINT
You have the option of using any two of the following
pointing devices at any given time; Quick Point, touch
screen or external PS/2 mouse. See “BIOS Setup
Utility” on page 29.
Figure 2-14 Double-clicking
Clicking
Clicking means pushing and releasing a button. To leftclick, move the cursor to the item you wish to select,
press the top button once, and then immediately release
it. To right-click, move the cursor to the item you wish
to select, press the bottom button once, and then immediately release it. (Figure 2-13)
CAUTION
If the interval between clicks is too long, the
double-click will not be executed.
POINT
Parameters for the Quick Point can be adjusted from
the Mouse Properties dialog box located in the
Windows Control Panel.
17
#
LifeBook B Series – Section Two
Dragging
Dragging means pressing and holding the top button,
while moving the cursor. To drag, move the cursor to
the item you wish to move. Press and hold the top
button while moving the item to its new location
and then release it. (Figure 2-15)
CAUTION
To avoid potential scratching and damage, never
use anything but the included stylus or your finger
with the Touch Screen.
POINT
To purchase additional or replacement styluses,
visit Fujitsu’s accessories web site at:
http://www.fujitsupc.com.
Figure 2-15 Dragging
Quick Point Device Control Adjustment
The Windows Control Panel allows you to customize
your Quick Point with selections made from within the
Mouse Properties dialog box. There are three aspects of
Quick Point operation, which you can adjust:
■
■
■
Buttons: This tab lets you set up the buttons for
right or left handed operation, in addition to
setting up the time interval allowed between
clicks in double-clicking.
Pointers: This tab lets you set up the scheme for
the cursor depending on its functionality.
Motion: This tab lets you set up a relation between
the speed of your finger motion and the speed of the
cursor. It also allows you to enable a Pointer Trail for
the cursor arrow.
TOUCH SCREEN
The integrated Touch Screen allows you to use either the
included stylus, or your finger, as a pointing device. You
can use the stylus to click, double-click, drag items and
icons, or to draw like a pen or pencil in applications that
support this behavior, such as drawing or painting
programs. See the documentation that came with your
application for details. (Figure 2-16)
Clicking
To left-click, touch the object you wish to select and then
lift the stylus tip immediately. The Touch Screen does
not support right-clicking. You also have the option to
perform the left-click operation by tapping lightly with
your finger on the Touch Screen once. (Figure 2-17)
Figure 2-17 Clicking the Touch Screen
Double-Clicking
To double-click, touch the item twice, and then immediately remove the stylus tip. You also have the option to
perform the double-click operation by tapping lightly
with your finger on the Touch Screen twice. (Figure 218)
Figure 2-18 Double-clicking the Touch Screen
POINT
If the interval between taps is too long, the
double-click will not be executed.
POINT
Figure 2-16 Using the Stylus with the Touch Screen
18
Parameters for the Touch Screen can be adjusted from
the Mouse Properties dialog box located in the
Windows Control Panel.
G e t t i n g t o K n o w Yo u r L i f e B o o k
Dragging
Dragging means touching the screen with the stylus,
moving and then lifting the stylus. To drag, tap the
Touch Screen twice with your stylus over the item you
wish to move, making sure to leave your finger on the
screen after the final tap. Next, move the item to its new
location by moving the stylus across the screen, and then
lifting the stylus to release it. Dragging can also be done
using your fingertip. (Figure 2-19)
6. Touch the stylus to various points on the screen to
verify that the screen is correctly calibrated. If you
are satisfied with the screen’s calibration, press the
[ENTER] key. If you are not satisfied, press the
[HOME] key to begin again at Step 2.
Figure 2-19 Dragging on the Touch Screen
Calibrating the Touch Screen
In order to ensure accurate tracking between the stylus
and cursor, you must run the Touch Screen Calibration
Utility before you use the Touch Screen for the first time,
or after you change the display resolution.
To run the calibration utility:
1. On the Start menu, point to Programs. Point
to Fujitsu Touch Panel/Compensation Tool. This
will
open the Compensation Tool.
2. Adjust the display of your LifeBook to a comfortable
angle and find the red + symbol in the upper-left
corner of the display.
3. Using the stylus, touch the screen near the + symbol
and without lifting the tip, move the stylus to the
center of the symbol. Once the stylus tip is in the
center of the symbol, lift it off the Touch Screen.
This will cause the red + to disappear from the
corner and reappear in a different place on
your screen.
4. Repeat step 3 until you have selected a total of nine
symbols. This is the minimum number of points
necessary to calibrate your touch screen.
5. Once you have selected the nine symbols, press the
[ENTER] key.
POINT
If you receive an error message at this point, you
selected fewer than nine symbols. Click OK and
begin again at Step 2.
19
LifeBook B Series – Section Two
Volume Control
Your Fujitsu LifeBook has multiple volume controls
which interact with each other.
CAUTION
Any software that contains audio files will also contain
a volume control of its own. If you install an external
audio device that has an independent volume control,
the hardware volume control and the software volume
control will interact with each other. It should be noted
that if you set your software volume to Off, you will
override the external volume control setting.
CONTROLLING THE VOLUME
The volume can be controlled in several different ways:
■
■
Volume can be set from within the Volume Control on
the Taskbar.
Volume can be controlled with the F8 and F9 functions keys. Pressing [F8] repeatedly while holding
[FN] will decrease the volume of your LifeBook. Pressing [F9] repeatedly while holding [FN] will increase
the volume of your LifeBook.
POINT
There are seventeen levels through which the function
keys cycle.
■
■
Volume can be controlled by many volume controls
that are set within individual applications.
Certain external audio devices you might connect to
your system may have hardware volume controls.
Each source discussed above puts an upper limit on the
volume level that must then be followed by the other
sources.
We recommend that you experiment with the various
volume controls to discover the optimal sound level.
20
G e t t i n g t o K n o w Yo u r L i f e B o o k
(1) Application A Button
(2) Application B Button
(3) Internet Button
(4) E-Mail Button
Enter Button
Figure 2-20 LifeBook Security/Application Panel
LifeBook Security/
Application Panel
one or up to four buttons simultaneously. The following
are valid button strokes:
■
■
A unique feature of your LifeBook is the Security/Application Panel that allows you to secure your LifeBook
from unauthorized use. The Security/Application Panel
also allows you to launch applications with a touch of a
button when your system is on.
If the security system is activated, upon starting your
LifeBook or resuming from suspend mode the security
system requires you to enter a password code using the
buttons on the Security/Application Panel. After entering
a correct password, your LifeBook resumes system
operation. (Figure 2-20)
SETTING UP YOUR LIFEBOOK SECURITY
PANEL
When you receive your LifeBook, the security panel
application is pre-installed without any passwords.
The following sections will provide detailed information
on your security panel, how to set, change or remove
passwords.
Numbered Buttons
Use these buttons to enter your password.(Figure 2-20)
Enter Button
After entering the button strokes, push this button to
enter the password into the LifeBook. (Figure 2-20)
■
■
Pushing [4] by itself
Pushing [2] and [3] at the same time
Pushing [1], [2], and [4] at the same time
Pushing [1], [2], [3], and [4] at the same time
The following are valid passwords. The numbers
within braces ({ }) are button strokes using more
than one button.
■
■
■
{[2]+[3]}, [1], [enter]
[4], [enter]
{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [enter]
Setting Passwords
When shipped from the factory, no passwords are set.
You have a choice of having no password or setting a
supervisor and user password. You must set the supervisor password before the user password.
POINT
The purpose of supervisor password is to be able to
bypass the user password in case the user password is
forgotten. The supervisor password alone will not lock
the system.
POINT
You have to set both the supervisor and user passwords
for the security panel to work.
PASSWORDS
The user and supervisor password may be set on this
LifeBook. A supervisor password is typically the same
for all LifeBooks in a working group, office, or company
to allow for system management. Individual LifeBooks
in a group environment should not use a common password. A password consists of one to five button strokes
plus the enter button. A valid stroke consists of pushing
Setting Supervisor Password
You must have set a supervisor password before setting
any user passwords. The supervisor password can bypass
the user password.
1. Go to the Start menu.
2. Click on Run.
3. Type in FJSECS.EXE, then press [Enter]
21
LifeBook B Series – Section Two
4. Follow the on-screen instructions to set the
Supervisor password.
Setting User Password
1 Go to the Start menu.
2. Click on Programs.
3. Click on Security Panel Application and
Set User Password.
4. Follow the on-screen instructions to set the
user password.
POINT
You may change or remove the supervisor or user
password by repeating the steps defined above.
OPERATING YOUR LIFEBOOK SECURITY/
APPLICATION PANEL
The security lock feature is in effect both when the system
resumes from Off or suspend state. You always need to
push the Suspend /Resume button to input the user password. Your system will not begin the boot sequence
without entering your supervisor/user password.
From Off State
1. Turn on your system.
2. When the Security Indicator flashes, enter the password and press Enter button.
For example, if the password is 22222,
Press Button Number 2 five times and press Enter
button.
The LifeBook will boot to normal operation.
From Suspend State
1. Press your Suspend/Resume button.
2. When the Security Indicator flashes, enter the password and press Enter button.
The LifeBook should resume normal operation.
Incorrect Password Entry
If an invalid supervisor or user password is entered three
times in succession, the system will “beep” for about one
minute. If a valid password is entered within a minute
(while system beeps), the beeping will stop and the LifeBook will resume normal operation. If no or an invalid
password is entered while the system beeps, the system
will return to its previous locked state (suspend or off)
and the Security Indicator will go off. To reactivate the
LifeBook after a password failure, you must press the
Suspend/Resume button, then enter a correct password.
22
POINT
Remember the user password you specified on the
Security Panel Application. If you forget the password
you will not be able to use your computer. The supervisor password can override the user password.
PRECAUTIONS
Opening and Closing the Cover
Closing the cover automatically places the LifeBook into
suspend mode. Opening the cover does not automatically place the LifeBook into normal operation. Instead,
you must enter the proper security password after
pushing the Suspend/Resume button.
Low Battery Operations
If your LifeBook has low battery, pushing the suspend/
resume button only turns on the Security Indicator.
Your LifeBook does not unlock, the Security Indicator
turns off after one minute. To resume normal operation,
first attach a power supply to the LifeBook. Then you
may unlock the LifeBook.
UNINSTALLING THE SECURITY
PANEL APPLICATION
You have two options when uninstalling the security
panel application:
■
■
Uninstall the security panel application software.
This will disable all security feature.
Uninstall the security panel application with password
still active. This will not allow any changes to the
password.
Uninstalling the Security Panel
Application Software
Remove passwords when User wants no password
protection whatsoever and doesn’t want to give anybody
the utility to set a password on their computer. In this
case, if passwords (supervisor, user, or both) are set, the
passwords must first be cleared BEFORE removing the
application. To clear passwords, follow same procedure
in SETTING PASSWORD CODES except this time,
select REMOVE, enter current password then click Next.
When asked to confirm select Yes.
Removing Security Panel Application with
Passwords Still Active
Using this feature will not allow any changes to
the password.
G e t t i n g t o K n o w Yo u r L i f e B o o k
POINT
Removing the applications does not remove the
password. It simply removes the utility to change/add/
remove passwords. To change your password you must
reinstall the application.
User:
1. Go to Start Menu, Click on Control Panel.
2. Open Add/Remove Programs Properties in the
Control Panel.
3. Select the Security Panel Application in the list, and
click Add/Remove.
4. When the Confirm File Deletion box appears,
click Yes.
Supervisor:
1. Go to Start Menu, Click on Control Panel.
2. Open Add/Remove Programs Properties in the
Control Panel.
3. Select the Security Panel Application for
Supervisor in the list, and click Add/Remove.
4. When the Confirm File Deletion box appears,
click Yes.
Reinstalling the Security/Application Panel
To reinstall supervisor or user security application, you
will need your Drivers and Utilities CD. The Secpanel
folder located in the Utilities\Security Panel contains
the setup files for supervisor and user security application.
1. Double-click the Setup FJSECS.EXE file. The
Installing Security Panel Application window will
appear. Follow the instructions on the screen.
2. Double-click the Setup FJSECU.EXE file. The
Installing Security Panel Application window will
appear. Follow the instructions on the screen.
Supervisor and user passwords can be set by the
Windows Software which are FJSECS.EXE and
FJSECU.EXE respectively. FJSECU.EXE for user
password cannot run without supervisor password.
First you need to run FJSECS.EXE to set supervisor
password before setting user password. Follow
instructions under Setting Passwords.
If you forget both passwords, please contact Fujitsu PC
Corporation Service and Support at 1-800-8FUJITSU
(1-800-838-5487). Fujitsu PC Corporation charges a
service fee for unlocking a password restricted LifeBook.
When calling please have a valid credit card and provide
proof of ownership. You will then be given instructions
on where to ship your LifeBook.
LAUNCHING APPLICATIONS WITH
THE SECURITY/APPLICATION PANEL
The security panel also enables you to launch applications
with the touch of a button when your system is on.
Pressing any of the buttons will launch a user-defined
application. Your LifeBook is pre-installed with software
utilities that let you operate and configure your LifeBook
Security /Application Panel. These utilities are found
under the Start menu, under Programs, then under LifeBook Application Panel. They include Application Panel
Setup, Application Panel Guide, Activate Panel and Deactivate Panel.
Configuring your LifeBook Application Panel
When you start Windows, the LifeBook Application
Panel is automatically activated. An icon resembling a
finger pressing a button will appear on the system tray
(the indented portion of the status bar where the clock is
displayed). When you see this icon you will know that
LifeBook Application Panel is active.
As an application launcher, the LifeBook Application
Panel is very flexible, giving you a variety of options. To
set up the Panel to best suit your needs, we have
provided the Application Panel Setup utility that quickly
and easily helps you make the most of this valuable
feature.
To configure your LifeBook Application Panel with
Application Panel Setup:
1. Click on Start.
2. Click on Programs.
3. Click on LifeBook Application Panel.
4. Click on Application Panel Setup.
The Application Panel Setup utility will appear. There
are tabs that correspond to the application buttons on
the LifeBook Application Panel. When you receive your
LifeBook, these buttons are pre-configured to launch
specific programs, as referenced in Chapter 7 of this
document.
POINT
The tabs in Application Panel Setup may not be in the
same order as the buttons on your LifeBook, please
select the tab you wish to change carefully.
To change an application associated with the Application buttons, click on the tab for the button you would
like to reconfigure – for example, Application 1. Click
on Browse from Start Menu, scroll down the list of
applications, click on the application you wish to launch
with this button, and then click OK. The button will
now launch the new application.
23
LifeBook B Series – Section Two
The Internet tab is different. It comes set to launch your
Windows default Internet browser (Internet Explorer),
unless you have changed this in Windows. In order to
reconfigure it to launch another program follow these
easy steps:
1. Click on Other from the Internet browser box.
2. Click on Browse from Start Menu.
3. Scroll down the list of applications, and then click
on the application you wish to launch with this
button.
4. Click OK.
The button will now launch the new application. If you
want to return to launching your Windows default
Internet browser with this button, you need only click
on “Default Internet Browser” from the Internet browser
box. Be aware that you will erase the settings for the
“other application”. If you wish to go back to launching
the “other application” from this button, you will need
to reconfigure it as described above.
POINT
If your system has dedicated one of the application
launcher buttons to be an Internet launcher, the button
can still be configured to launch any application you
wish, not just an Internet browser.
When you have finished with Application Panel Setup
click OK, and the new settings will take effect. You can
reconfigure your LifeBook Application Panel as often as
you like.
24
Deactivating and Activating the LifeBook
Application Panel
To deactivate the LifeBook Application Panel, follow
these easy steps:
1.
2.
3.
4.
Click on Start.
Click on Programs.
Click on LifeBook Application Panel.
Click on Deactivate Panel.
To reactivate, follow the same procedure, except for
step 4. Click on Activate Panel instead.
POINT
Every time you start Windows the LifeBook Application
Panel is activated, even if you deactivated it before you
shut down.
3
Getting Started
25
!
LifeBook B Series – Section Three
26
"
Getting Started
DC Power Jack
DC Output Cable
AC Adapter
AC Cable
Figure 3-1 Connecting the AC Adapter
Power Sources
Your LifeBook has three possible power sources: a
primary Lithium ion battery, an AC adapter or an
optional Auto/Airline adapter.
CONNECTING THE POWER ADAPTERS
The AC adapter or optional Auto/Airline adapter
provides power for operating your LifeBook and
charging the batteries.
Connecting the AC Adapter
1. Plug the DC output cable into the DC power jack
of your LifeBook.
2. Plug the AC adapter into an AC electrical outlet.
(Figure 3-1)
Connecting the Optional Auto/Airline Adapter
1. Plug the DC output cable into the DC power jack
on your LifeBook.
2. Plug the Auto/Airline adapter into the cigarette
lighter of an automobile with the ignition key in
the On or Accessories position.
OR
3. Plug the Auto/Airline adapter into the DC power
jack on an airplane seat.
Switching from AC Adapter Power or the
Auto/Airline Adapter to Battery Power
1. Be sure that you have at least one charged
battery installed.
2. Remove the AC adapter or the Auto/Airline adapter.
CAUTION
The Lithium ion battery is not charged upon purchase.
Initially, you will need to connect either the AC adapter
or the Auto/Airline adapter to use your LifeBook.
27
#
LifeBook B Series – Section Three
Display Panel Latch
Figure 3-2 Opening the Display Panel
Display Panel
Your LifeBook contains a display panel that is backlit for
easier viewing in bright environments and maintains top
resolution through the use of active-matrix technology.
OPENING THE DISPLAY PANEL
1. Slide the Display Panel latch. This releases the
locking mechanism and raises the display slightly.
2. Lift the display backwards, being careful not to
touch the screen, until it is at a comfortable
viewing angle. (Figure 3-2)
ADJUSTING DISPLAY PANEL BRIGHTNESS
Once you have turned on your LifeBook, you may want
to adjust the brightness level of the screen to a more
comfortable viewing level. There are two ways to adjust
the brightness, keyboard and power management utility.
Keyboard
Adjusting the brightness using the keyboard changes the
setting only temporarily.
■
[Fn+F6]: Pressing repeatedly will lower the
brightness of your display.
■
[Fn+F7]: Pressing repeatedly will increase the
brightness of the display.
POINT
If using AC power your brightness setting is set to its
highest level by default. If using battery power your
brightness settings is set to approximately mid-level by
default.
Power Management Utility
(Windows 98 Second Edition models only)
Adjusting the brightness using the Power Management
Utility changes the setting permanently.
28
1. Double-click the Battery Icon in the lower right
corner of your display. This will open the BatteryAid
Properties dialog box.
2. Select the Power Control tab and adjust your
LCD Backlighting to the desired level.
3. Click OK or Apply to permanently change
the settings.
You may need to readjust the brightness level periodically depending on your operating environment.
POINT
The higher the brightness level, the more power the
LifeBook will consume and the faster your batteries
will discharge. For maximum battery life, make sure that
the brightness is set as low as possible.
CLOSING THE DISPLAY PANEL
1. Holding the edge of your display panel, pull it
forward until it is flush with the body of your LifeBook.
2. Push down until you hear a click. This will
engage the locking mechanism and prevent
your display panel from opening unexpectedly.
Getting Started
Starting Your LifeBook
POWER ON
Power Switch
The power switch is used to turn on your LifeBook from
its off state. Once you have connected your AC adapter
or charged the internal Lithium ion battery, you can
power on your LifeBook. (See figure 2-7 on page 11 for
location)
memory is empty, and it needs to find instructions to
start up your LifeBook. This information is in the BIOS
program. Each time you power up or restart your LifeBook, it goes through a boot sequence which displays a
Fujitsu logo until your operating system is loaded.
During booting, your LifeBook is performing a standard
boot sequence including a Power On Self Test (POST).
When the boot sequence is completed without a failure
and without a request for the BIOS Setup Utility, the
system displays the operating system’s opening screen.
The boot sequence is executed when:
CAUTION
When you turn on your LifeBook be sure you have a
power source. This means that at least one battery is
installed and charged, or that the AC or Auto/Airline
adapter is connected and has power.
■
■
■
■
Facing the right-side panel of your LifeBook, move the
power switch to the right, this is the On position. The
power switch moved to the left is the Off position. When
you are done working you can either leave your LifeBook in Suspend mode, See “Suspend Mode” on
page 32., or you can turn it off. See “Power Off” on
page 34.
CAUTION
Do not carry your LifeBook around with the power on
or subject it to shocks or vibration, as you risk damaging
your LifeBook.
When you Power On your LifeBook, it will perform a
Power On Self Test (POST) to check the internal parts
and configuration for correct functionality. If a fault is
found, your LifeBook will emit an audio warning and/or
an error message will be displayed. See “Power On Self
Test Messages” on page 61. Depending on the nature of
the problem, you may be able to continue by starting the
operating system or by entering the BIOS setup utility
and revising the settings.
After satisfactory completion of the Power On Self Test
(POST), your LifeBook will load your operating system.
CAUTION
Never turn off your LifeBook during the Power On
Self Test (POST) or it will cause an error message to
be displayed when you turn your LifeBook on the next
time. See “Power On Self Test Messages” on page 61.
BOOT SEQUENCE
The procedure for starting-up your LifeBook is termed
the Bootup sequence and involves your LifeBook’s BIOS.
When your LifeBook is first turned on, the main system
You turn on the power to your LifeBook.
You restart your LifeBook from the Windows
Shut Down dialog box.
The software initiates a system restart. Example:
When you install a new application.
You reset the system by pressing the three keys
[CTRL+ALT+DEL].
BIOS SETUP UTILITY
The BIOS Setup Utility is a program that sets up the
operating environment for your LifeBook. Your BIOS
is set at the factory for normal operating conditions,
therefore there is no need to set or change the BIOS’
environment to operate your LifeBook.
The BIOS Setup Utility configures:
■
■
Device control feature parameters, such as changing
I/O addresses and boot devices.
System Data Security feature parameters, such
as passwords.
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility do the following:
1. Turn on or restart your LifeBook.
2. Press the [F2] key once the Fujitsu logo appears
on the screen. This will open the main menu
of the BIOS Setup Utility with the current
settings displayed.
3. Press the [RIGHT ARROW] or [LEFT ARROW] key
to scroll through the other setup menus to review or
alter the current settings.
BIOS Guide
A guide to your LifeBook’s BIOS is available online.
Please visit our service and support Web site at
www.fujitsupc.com/support. Once there, click on the
Self Help Center link, and select your LifeBook series
from the pull-down menu. Once you have done that,
select the heading BIOS Guides from the pull-down
menu and finally, select your specific unit’s BIOS
number. If you are unsure of your LifeBook’s BIOS
number, please
refer to your packing slip.
29
LifeBook B Series – Section Three
POINT
If your data security settings require it, you may be
asked for a password before the BIOS main menu
will appear.
BOOTING THE SYSTEM
WITH WINDOWS 98 SECOND EDITION
We strongly recommend that you not attach any external
devices and do not put a CD or floppy disk in
any drive until you have gone through the initial power
on sequence.
When you turn on your LifeBook for the first time,
it will display a Fujitsu logo on the screen. If you do
nothing the system will read the hard drive for the
operating system software, flash the LifeBook
configuration information on the screen, and then the
Windows 98 Second Edition Welcome will begin.
Designed to accommodate the needs of many users,
in many different countries, Windows 98 Second Edition
needs to be configured the first time you use it.
Windows 98 Second Edition has three parts:
■
■
■
Getting Started: You have the opportunity to enter
custom information for your configuration file and
setup your modem so that your LifeBook will be
prepared to dial out.
Registration: Easy online registration for Windows
98 with Microsoft, and for your LifeBook with Fujitsu
PC Corporation.
Windows License Agreement and Final Settings:
You have the opportunity to review the Windows 98
Second Edition License Agreement and then your
configuration file will be generated.
POINT
You may click Cancel at any time within this process to
shutdown Windows 98 Second Edition. You may restart
this process at any time in the future, but you must
complete it in order to use your computer.
Getting Started
Read the instructions on the screens carefully and fill
in the information as directed. You will be asked to enter
several pieces of identification information and how you
access the Internet. For the modem settings, enter your
current location information where you will be using
your LifeBook. If you are not connected to a phone line
and plan to register at a later time, you may click the
Skip button, and you will go directly to the condition
of use page.
Once you have setup your LifeBook to dial out,
Windows 98 Second Edition will make a free
30
telephone call which will test these settings. If the call is
unsuccessful, you will be returned to the phone settings
page where you may try to fix them. If you are unable to
fix the settings please contact Fujitsu PC Service and
Support. See “Fujitsu PC Contact Information” on
page 3. If you would simply like to move on, and register
at a later time, you may click the Skip button, and you
will go directly to the Condition of Use page.
Registration
If your connection is successful, you will go to the
Registration Confirmation page. On this page simply
enter the requested information, and then check the
box at the bottom to register your copy of Windows 98
Second Edition with Microsoft. Once you have finished,
click the Next button to continue.
POINT
If you do not register at this time you can do it later
simply by double-clicking on the LifeBook Registration
icon on your desktop and following the instructions.
You will then go through the Fujitsu registration process.
Follow the instructions on the screens, and enter all of
the necessary information. Be as specific as possible so
that if you need help the service and support team will
be able to serve you better.
Final Settings
The first part of your final settings is the Windows End
User License Agreement. Read the agreement carefully.
When you finish reading you must accept or reject the
terms of the agreement and then click on the Next
button.
POINT
If you reject the terms of the license agreement you
will be asked to review the license agreement for
information on returning Windows 98 Second Edition
or to shut down your LifeBook.
POINT
You cannot use your LifeBook until you have accepted
the License Agreement. If you stop the process your
LifeBook will return to the beginning of the Windows
98 Second Edition Welcome Process, even if you shut
your LifeBook down and start it up again.
Getting Started
INSTALLING CLICK ME! (WINDOWS 98
ONLY)
you can also double-click on the LifeBook Registration
icon on your desktop and then follow the instructions.
The first time you boot up your system, you will see an
icon on the desktop called Click Me!. When you click the
Click Me! icon, your system will automaticaly build the
icon tray in the bottom right of the screen. These icons
provide links to utilities that you will frequently access.
Although the icon remains on the screen, you need
invoke it only once. When you click Click Me!, the
following pre-installed applications and utilities will be
activated and appear on the taskbar:
■
■
■
■
■
McAfee ActiveShield
BatteryAid
LifeBook Application Panel
ATI Display Properties
Alps Touchpad
BOOTING THE SYSTEM WITH WINDOWS
2000 PROFESSIONAL
We strongly recommend that you not attach any
external devices and do not put a CD or floppy disk in
any drive until you have gone through the initial power
on sequence.
POINT
Make sure you have connected a phone line to your
modem before you use E-Registration.
You may also complete the pre-printed registration form
and either:
Fax to 1-800-511-9989
Mail to:
Fujitsu PC Corporation
5200 Patrick Henry Drive
Santa Clara, CA 95054
Attn: Warranty Department
You may also register on our Web site:
■
■
■
www.fujitsupc.com/support
You will need to be set up with an Internet Service
Provider (ISP) to use this option.
When you turn on your LifeBook for the first time,
it will display a Fujitsu logo on the screen and then the
Windows 2000 setup screen will appear. The Windows
2000 Professional setup will prompt you through a
series of screens. You will be asked to enter custom and
computer information, user password, date and time,
workgroup or computer domain and accept or reject the
license agreement. Once you have entered all the information you will be asked to restart your computer.
POINT
If you reject the terms of the license agreement you
will be asked to review the license agreement for
information on returning Windows 2000 Professional or
to shut down your LifeBook.
REGISTERING YOUR LIFEBOOK
What are the benefits of registering?
You will receive an identification label for your LifeBook, which, if your LifeBook is ever lost, may help in
getting it returned to you. You also receive priority
Personal Identification Number (PIN) technical support
access and useful product mailings. Proof of purchase is
not required if you register within 30 days of your
purchase.
How do I register?
With Windows 98 Second Edition, it is a part of the
Welcome process. For Windows 98 and Windows 2000,
31
LifeBook B Series – Section Three
Power Management
Your LifeBook has many options and features for
conserving battery power. Some of these features are
automatic and need no user intervention, such as those
for the internal modem. However, others depend on the
parameters you set to best suit your operating conditions, such as those for the display brightness. Internal
power management for your LifeBook may be
controlled from settings made in your operating system,
pre-bundled power management application, or from
settings made in BIOS setup utility.
Besides the options available for conserving battery
power, there are also some things that you can do to
prevent your LifeBook battery from running down as
quickly. For example, you can create an appropriate
power saving profile, put your LifeBook into Suspend
mode when it is not performing an operation, and you
can limit the use of high power devices. As with all
mobile, battery powered computers, there is a trade-off
between performance and power savings.
SUSPEND/RESUME BUTTON
When your LifeBook is active, the Suspend/Resume
button can be used to manually put your LifeBook
into Suspend mode. Push the Suspend/Resume button
when your LifeBook is active, but not actively accessing
anything, and immediately release the button. You will
hear two short beeps and your system will enter Suspend
mode. (See figure 2-5 on page 8 for location).
If your LifeBook is suspended, pushing the Suspend/
Resume button will return your LifeBook to active operation. You can tell whether or not your system is in
Suspend mode by looking at the Power indicator. See
“Power Indicator” on page 13. If the indicator is visible
and not flashing, your LifeBook is fully operational. If
the indicator is both visible and flashing, your LifeBook
is in Suspend mode. If the indicator is not visible at all,
the power is off or your LifeBook is in Save-to-Disk
mode (See Save-to-Disk Mode)
32
SUSPEND MODE
Suspend or Standby mode in Windows saves the
contents of your LifeBook’s system memory during
periods of inactivity by maintaining power to critical
parts. This mode will turn off the CPU, the display, the
hard drive, and all of the other internal components
except those necessary to maintain system memory and
allow for restarting. Your LifeBook can be put in
Suspend mode by:
■
■
■
■
Pressing the Suspend/Resume button when your
system is turned on.
Selecting Standby from the Windows Shut Down
menu.
Timing out from lack of activity.
Allowing the battery to reach the Dead Battery
Warning condition.
Your LifeBook’s system memory typically stores the
file(s) on which you are working, open application(s)
information, and any other data required to support the
operation(s) in progress. When you resume operation
from Suspend mode, your LifeBook will return to the
point where it left off. To resume operation, you must
use the Suspend/Resume button to resume operation,
and there must be an adequate power source available,
or your LifeBook will not resume.
CAUTION
If you are running your LifeBook on battery power,
be aware that the battery continues to discharge while
your LifeBook is in Suspend mode, though not as fast as
when fully operational.
SAVE-TO-DISK MODE
(Windows 98 Second Edition models only)
The Save-to-Disk mode saves the contents of your
LifeBook’s system memory to the hard drive as a part
part of the Suspend/Resume mode. Your LifeBook is
pre-configured to perform this function. The Save-toDisk mode can also be configured through the system
BIOS to run in other ways depending on what you need
to accomplish. See “BIOS Setup Utility” on page 29.
Getting Started
Default Methods for using Save-to-Disk Mode:
1. Press the [Fn] button together with the Suspend/
Resume button. This will open a Save-to-Disk dialog
box and begin the process.
Customer Configured BIOS Methods for using
Save-to-Disk Mode:
1. Click on the Start button, click Shut Down and
and then Standby. Prior to that you should enable
Save-to-Disk in the BIOS setup utility.
OR
2. Enable Save-To-Disk mode from within the Power
dialog box of the BIOS setup utility, then press the
Suspend/Resume button to execute this command
under DOS or Windows 98 Second Edition.
OR
3. Enable Save-To-Disk mode from within the Power
dialog box of the BIOS setup utility, then allow the
LifeBook to time out from lack of activity.
CAUTION
The Suspend or Save-to-Disk mode should not be used
with certain PC Cards. Check your PC Card
documentation for more information.
POINTS
■
■
Disabling the Suspend/Resume button prevents it
from being used to put your LifeBook in Suspend
or Save-to-Disk mode. The resume function of the
button cannot be disabled.
If your LifeBook is actively accessing information
when you enter the Suspend or Save-to-Disk mode,
changes to open files are not lost. The files are left
open and memory is kept active during Suspend
mode or the memory is transferred to the internal
hard drive during Save-to-Disk mode.
■
When PC Cards or external devices are in use, Saveto-Disk mode cannot return to the exact state prior
to suspension, because all of the peripheral devices
will be re-initialized when the system restarts.
■
The main advantage of using the Save-to-Disk function is that power is not required to maintain your
data. This is particularly important if you will be
leaving your LifeBook in a suspended state for a
prolonged period of time. The drawback of using
Save-to-Disk mode is that it lengthens the power
down and power up sequences and resets peripheral
devices.
POINT
Save-to-Disk mode requires allocating a significant
amount of hard drive capacity for saving all system
memory, which reduces your usable disk space. When
you purchase your LifeBook it will have space allocated
for the memory installed. If you upgrade the original
system by adding a memory upgrade module without
changing the size of your Save-to-Disk allocation you
will get an error message when you try to activate Saveto-Disk mode and it will not work. Use the PHDISK
Utility to increase the size of the Save-to-Disk file,
SAVE2DSK.BIN. You can download the Save-to-Disk
File Allocation information from our Web site at
www.fujitsupc.com. If you need help, contact your
support representative for recommendations.
HIBERNATION FEATURE
(Windows 2000 Professional models only)
The Hibernation feature saves the contents of your
LifeBook’s system memory to the hard drive as a part
of the Suspend/Resume mode. You can enable or disable
this feature. To use the Hibernation feature follow these
easy steps:
1. Click on the Start button, click Shut Down.
2. Select Hibernate option from the “What do you
want the computer to do” list.
Enable or Disable the Hibernation Feature
The default setting is enabled. To enable or disable the
Hibernation feature follow these easy steps:
1. From the Start menu, select Settings, and then select
Control Panel.
2. Select Hibernation, and then select the box to
enable or disable this feature.
IDLE MODE
Idle mode is one of the power management parameters.
When Idle mode is enabled, the CPU is put into lowspeed operation when there is no activity (keystroke,
pointer action, sound generation, video display change,
modem transmission or reception, etc.) on your LifeBook for 16 seconds. Any activity will cause the normal
operation to restart automatically. This feature is independent of the Suspend/Resume modes.
STANDBY MODE
Standby mode is one of the power management parameters. When Standby mode is activated, your LifeBook
shuts off the display and turns off the hard drive when
there is no activity (keystroke, pointer action, sound
generation, video display change, modem transmission
or reception, etc.) on your LifeBook for the user selected
time-out period. Any activity will cause your LifeBook
33
LifeBook B Series – Section Three
to return to normal operation automatically. This
feature is independent of the Suspend/Resume button.
DISPLAY TIMEOUT
The Video Timeout is one of the power management
parameters. This feature saves power by turning off the
display if there is no keyboard or pointer activity for the
user selected timeout period. Any keyboard or pointer
activity will cause the display to restart automatically.
This feature is independent of the Suspend/Resume
button and can be enabled and disabled in Windows and
BIOS setup utility. See “BIOS Setup Utility” on page 29.
HARD DISK TIMEOUT
The Hard Disk Timeout is another one of the power
management parameters. This feature saves power by
turning off the hard drive if there is no hard drive
activity for the user selected timeout period. Any
attempt to access the hard drive will cause it to restart
automatically. This feature is independent of the
Suspend/Resume button and can be enabled and
disabled in Windows and BIOS setup utility. See “BIOS
Setup Utility” on page 29.
WINDOWS POWER MANAGEMENT
The Power Management icon located in the Windows
Control Panel allows you to configure some of the power
management settings. For example, you can use the
Power Management to set the timeout values for turning
off the display and hard disks whether you are running
the LifeBook on battery power or one of the adapters.
The settings may also be changed in the BIOS. See “BIOS
Setup Utility” on page 29.
RESTARTING THE SYSTEM
If your system is on and you need to restart it, be sure
that you use the following procedure.
1. Click the Start button, and then click Shut Down.
2. Select the Restart option from within the Windows
Shut Down dialog box.
3. Click OK. Your LifeBook will shut down and then
reboot.
CAUTION
Turning off your LifeBook without exiting Windows or
turning on your LifeBook within 10 seconds of the
LifeBook being shut off may cause an error when you
start the next time.
34
POWER OFF
Before turning off the power by choosing Shut Down
from the Windows Start menu, check that the Hard
Drive, CD-ROM, PC Card and the Floppy Disk Drive
Access indicators are all Off. (See Figure 2-5 on page 8) If
you turn off the power while accessing a disk or PC Card
there is a risk of data loss. To assure that your LifeBook
shuts down without error, use the Windows shut down
procedure.
CAUTION
Be sure to close all files, exit all applications, and shut
down your operating system prior to turning off the
power with the power switch. If files are open when
you turn the power off, you will lose any changes that
have not been saved, and may cause disk errors.
Using the correct procedure to shut down from
Windows, allows your LifeBook to complete its operations and turn off power in the proper sequence to avoid
errors. The proper sequence is:
1. Click the Start button, and then click Shut Down.
2. Select the Shut Down option from within the
Windows Shut Down dialog box.
3. Click OK.
4. Move the power switch to the off position.
If you are going to store your LifeBook for a month or
more see the Care and Maintenance section.
4
User-Installable
Features
35
!
LifeBook B Series – Section Four
36
"
User Installable Features
Lithium ion Battery
Your LifeBook has a Lithium ion battery that provides
power for operating your LifeBook when no external
power source is available. The battery is durable and
long lasting, but should not be exposed to extreme
temperatures, high voltages, chemicals or other hazards.
The Lithium ion battery operating time may become
shorter if it is used under the following conditions:
■
■
When used at temperatures that exceeds a low of
5°C (40°F) or a high of 35°C (95°F). Extreme temperatures not only reduce charging efficiency, but can also
cause battery deterioration. The Charging icon
on the Status Indicator panel will flash when you try
to charge a battery that is outside its operating temperature range. See “Battery Charging Indicators” on
page 14.
When using a high current device such as a modem,
CD-ROM drive, or the hard drive, using the AC
adapter will conserve your battery life.
CAUTION
Actual battery life will vary based on screen brightness,
applications, features, power management settings,
battery condition and other customer preferences.
CD-ROM drive or hard drive usage may also have a
significant impact on battery life. The battery charging
capacity is reduced as the battery ages. If your battery is
running low quickly, you should replace it with a new
one.
CAUTION
Do not leave a faulty battery in your LifeBook. It
may damage your AC adapter, optional Auto/Airline
adapter, another battery or your LifeBook itself. It may
also prevent operation of your LifeBook by draining all
available current into the bad battery.
CAUTION
Under federal, state, or local law it may be illegal to
dispose of batteries by putting them in the trash. Please
take care of our environment and dispose of batteries
properly. Check with your local government authority
for details regarding recycling or disposing of old
batteries. If you cannot find this information elsewhere,
contact your support representative at 1-800-8FUJITSU
(1-800-838-5487).
The Lithium ion battery is recharged internally using
the AC adapter or Auto/Airline adapter. To recharge the
battery make sure the battery that needs to be charged
is installed in your LifeBook and connect the AC or
Auto/Airline adapter.
POINT
Make sure that the Battery Charging indicator and the
percentage charge is shown inside the Battery Level
icon on the Status Indicator Panel.
There is no memory effect on the Lithium ion battery
therefore you do not need to discharge the battery
completely before recharging. The charge times will be
significantly longer if your LifeBook is in use while the
battery is charging. If you want to charge the battery
more quickly, put your LifeBook into Suspend mode,
or turn it off while the adapter is charging the battery.
See “Power Management” on page 32.
CAUTION
Using heavy current devices such as Modem or
frequent CD-ROM and PCMCIA powered external
devices accesses may prevent charging completely.
Low Battery State
When the battery is running low, your LifeBook will
beep every 15 seconds and the Battery Level indicator
will flash. If you do not respond to the low battery
alarm, the batteries will continue to discharge until they
are
too low to operate. When this happens there will be a
multiple beep alarm and the Battery Level indicator will
show a dead battery. Your LifeBook will then go into
Suspend mode to try and protect your data for as long
as possible. There is no guarantee that your data will not
be lost once the LifeBook reaches this point.
CAUTION
You may not be able to hear the audio alarm if the
volume control is set too low or is turned off by either
the hardware or software. However, you will still be
able to see the Battery Level indicator flash. Once the
low battery alarm occurs you need to save all your
active data and put your LifeBook into Suspend mode
until you can provide a new power source. You should
provide a charged battery, an AC power adapter, or
Auto/Airline as soon as possible.
RECHARGING THE BATTERIES
If you want to know the condition of the primary
Lithium ion battery, check the Battery Level indicator
located on the Status Indicator panel. The indicator
changes as the battery level changes.
37
#
LifeBook B Series – Section Four
CAUTION
When you are in Suspend mode there must always be
at least one power source active. If you turn off the
power with the power switch, or remove all power
sources while your LifeBook is in Suspend mode, any
data that has not been saved to the hard drive will be
lost.
Dead Battery Suspend mode shows on the Status indicator just like the normal Suspend mode. Once your
LifeBook goes into Dead Battery Suspend mode you
will be unable to resume operation until you provide
a source of power either from an adapter, or a charged
battery. Once you have provided power, you will need to
press the Suspend/Resume button to resume operation.
In the Dead Battery Suspend mode, your data can be
maintained for some time, but if a power source is not
provided promptly, the Power indicator will stop
flashing and go out, meaning that you have lost the data
that was not stored. Once you provide power, you can
continue to use your LifeBook while an adapter is
charging the battery.
Shorted Batteries
The Status Indicator panel uses a symbol inside the
battery outline of the Battery Level indicator to display
the operating level available in that battery.
(See figure 2-10 on page 13) If this display shows a
Shorted Battery, it means that the battery is damaged
and must be replaced so it does not damage any other
parts of your LifeBook.
REPLACING THE BATTERY
Your LifeBook B Series comes with two battery packs:
one installed and one spare. By keeping the spare battery
fully charged, you can immediately swap with one that is
not charged. There are two ways to swap batteries: coldswapping and warm-swapping:
Cold-swapping Batteries
To cold-swap batteries in your battery bay follow these
easy steps: (Figure 4-1)
1. Have a charged battery ready to install.
2. Shut down your LifeBook and disconnect
the AC adapter.
3. Slide the Battery Bay Lock to the right, then slide the
battery release button in the same direction.
4. Slide the battery away from the battery bay and
remove it from the bay.
5. Position the new battery on the tray slides and carefully slide it fully into the tray. (Figure 4-2)
6. Slide the Battery Bay Lock to the left to lock the pack
into position.
7. Plug in the AC adapter and turn the power on.
38
Battery Bay Lock/
Release Button
2
1
1 - Battery Lock
2 - Battery Release
Button
Battery
Figure 4-1 Removing the Battery
Battery Slides
(both sides)
Figure 4-2 Installing the Battery
Warm-swapping Batteries
To warm-swap batteries in your battery bay follow these
easy steps: (Figure 4-1)
1. Close any open files and put your LifeBook into
suspend mode.
3. Slide the Battery Bay Lock to the right, then slide the
Battery Release Button in the same direction.
4. Slide the battery away from the battery bay and
remove it from the bay.
5. Position the new battery on the tray slides and carefully slide it fully into the tray. (Figure 4-2)
6. Slide the Battery Bay Lock to the left to lock the pack
into position.
7. Press the Suspend/Resume button to return your
LifeBook to normal operation.
CAUTION
If the Lithium ion battery connector is not fully seated,
you may not be able to use your LifeBook or charge
your battery.
User Installable Features
Eject Button
Figure 4-3 Loading/Ejecting a 3.5” Floppy Disk
External Floppy Disk
Drive
Your LifeBook has an external floppy disk drive which
can read and write information on removable 1.44MB
and 720KB floppy disks.
LOADING A DISK
To load a disk into your disk drive, follow these easy
steps:
This preparation is called formatting or initializing a
disk. You will need to format new disks, unless they are
preformatted. (Please refer to your operating system
manual for step-by-step instructions on formatting a disk)
To prevent accidental erasure of the data stored on a
disk, slide the “write protect” tab until a small hole is
exposed. This sets the disk into a protected state where
nothing can be added or removed. If you want to add or
remove data on a protected disk, slide the “write
protect” tab to close the small hole. (Figure 4-4)
1. Orient the disk so that its label is facing upwards
and the shutter side is pointing towards the drive.
(Figure 4-3)
2. Push the disk into the drive until the Eject button
pops out and you hear a click.
Write Enabled
POINT
When there is no disk in the drive, the Eject button is
flush with your LifeBook.
EJECTING A DISK
To eject a disk from the disk drive, follow these easy
steps:
1. Check that the Floppy Disk Drive Access indicator
is inactive.
2. Press the Eject button. This will push your disk
partially out of the drive.
3. Remove the disk.
Write Protected
Figure 4-4 Floppy Disk Write Protect
CAUTION
Formatting a floppy disk that already contains data will
erase all of the information on the disk.
CAUTION
If you eject the disk while the Floppy Disk Drive Access
indicator is active, there is a risk of damaging the data
on the disk, the disk itself or even the disk drive.
PREPARING A DISK FOR USE
Before you can use a new disk, it needs to be prepared
so your LifeBook knows where to store information.
39
LifeBook B Series – Section Four
PC Card Slot
PC Card
Eject Button
Figure 4-5 Installing/Removing PC Cards
PC Cards
Your LifeBook supports Type II and Type III PC Cards,
which can perform a variety of functions.
Some available PC Cards:
■
■
■
■
■
■
Fax/data modem cards.
Local area network (LAN) cards.
IDE solid-state disk cards.
SCSI cards.
Other PC Cards that conform to PCMCIA 2.1 or
CardBus standards.
Optional SmartCard adapter
For further information, refer to the instructions
supplied with your PC Card.
INSTALLING PC CARDS
PC Cards are installed in the PC Card slot. To install a
PC Card, follow these easy steps: (Figure 4-5)
WARNING
Installing or removing a PC Card during your LifeBook’s
shutdown or bootup process may damage the card
and/or your LifeBook.
3. Insert your PC Card into the slot, with the product
label facing up.
4. Push the card into the slot firmly until it is seated in
the opening.
REMOVING PC CARDS
To remove a PC Card, follow these easy steps:
CAUTION
Windows has a shutdown procedure for PC Cards
that must be followed before removing a card.
(Please review your operating system manual for
the correct procedure)
1. See your PC Card manual for specific instructions
on removing your card. Some PC Cards may require
your LifeBook to be in Suspend Mode or Off while
removing them.
POINT
If the dialog box states that the device cannot be
removed, you must save all of your open files, close
any open applications and shutdown your LifeBook.
Once your LifeBook has been shutdown, you must turn
Off the power using the power switch.
WARNING
Do not insert a PC Card into a slot if there is water or
any other substance on the card as you may
permanently damage the card, your LifeBook, or both.
1. See your PC Card manual for specific instructions
on the installation of your card. Some PC Cards
may require your LifeBook to be Off while
installing them.
2. Make sure there is no PC Card currently in the slot.
If there is, see Removing PC Cards.
40
2. Push the Eject button until it pops out, and then
push it in to eject the card. This will allow you to
remove the card.
CAUTION
If the PC Card has an external connector and cable, do
not pull the cable when removing the card.
User Installable Features
SMARTCARD READER
An embedded SmartCard Reader is provided on your
LifeBook. SmartCards are the same size and shape as
credit cards, but they contain an integrated microprocessor chip. The chip can hold a variety of different
information, and provides the user with many possible
options, such as allowing them to make secure
purchases, pay for phone calls, store security information, and provide personal identification and information.
In order to use the embedded SmartCard Reader, you
must purchase an optional SmartCard adapter for
installation into an available Type II PC Card slot.
41
LifeBook B Series – Section Four
Memory Upgrade
Module
Your LifeBook has been configured with either 64MB or
128MB of high speed Synchronous Dynamic RAM
(SDRAM) factory installed. To increase your LifeBook’s
memory capacity, you must replace the original memory
module with a higher capacity module. The memory
upgrade must be a dual-in-line (DIMM) 100 MHz
SDRAM module.
upgrade module with the connector slot in the
compartment. The connector will be pointing
toward the rear of the LifeBook.
8. Insert the memory upgrade module at a 45° angle.
Press the connector edge of the module firmly down
and into the connector until it lodges under the
retaining clip. You will hear a click when it is properly in place. (Figure 4-7)
CAUTION
Do not remove any screws from the memory upgrade
module compartment except those specifically shown in
the directions for installing and removing the memory
upgrade module.
INSTALLING A MEMORY UPGRADE
MODULE
1. Turn off power to your LifeBook using the power
switch, and remove any attached power adapter
(AC or auto/airline).
2. Make sure that all connector covers are closed.
3. Turn the LifeBook bottom side up, with the front
panel toward you.
4. Remove the screws of the memory upgrade module
compartment. (Figure 4-6)
5. Remove the cover.
Figure 4-7 Installing a Memory Upgrade Module
9. Replace the cover.
10. Replace the screws.
POINT
The memory upgrade module is not something you
routinely remove from your LifeBook. Once it is
installed, you should leave it in place unless you want
to change system memory capacity.
REMOVING A MEMORY UPGRADE MODULE
1. Perform steps 1 through 5 of Installing a Memory
Upgrade Module.
2. Pull the clips sideways away from each side of the
memory upgrade module at the same time.
3. While holding the clips out, remove the module
from the slot by lifting it up and pulling towards the
rear of your LifeBook. (Figure 4-8)
Figure 4-6 Opening the Memory Upgrade Compartment
CAUTION
The memory upgrade module can be severely damaged
by electrostatic discharge (ESD). Be sure you are
properly grounded when handling and installing the
module.
Figure 4-8 Removing a Memory Upgrade Module
6. Remove the memory upgrade module from the
static guarded sleeve.
7. Align the memory upgrade module with the part
side up. Align the connector edge of the memory
42
4. Store the memory upgrade module in a static
guarded sleeve.
User Installable Features
5. Replace the cover by following steps 9 and 10 of
Installing a Memory Upgrade Module.
POINT
After installing your new memory module, you must
complete the Resetting the Save-to-Disk Parameters
procedure in order for the Save-to-Disk mode to
operate properly on your LifeBook. See “Save-to-Disk
Mode (Windows 98 Second Edition models only)” on
page 32.
CHECKING THE COMPUTER RECOGNITION
OF NEW MEMORY CAPACITY
Once you have changed the system memory capacity, be
sure to check that your LifeBook has recognized the
change.
You can check the memory capacity by looking at the
main menu of the BIOS setup:
1. Turn on the power to your LifeBook using the
power switch.
2. Allow the system to start booting and press the [F2]
key once the Fujitsu logo appears on the screen. This
will open the main menu of the BIOS setup with the
current settings displayed. See “BIOS Setup Utility”
on page 29.
The System Memory and the Extended Memory
capacity, as detected by your LifeBook during the Power
On Self Test (POST), are displayed at the bottom of the
main menu screen.
POINT
If the total memory displayed is incorrect, check that
your memory upgrade module is properly installed. If
the module is properly installed and the capacity is still
not correctly recognized, see the Troubleshooting
section. See “Troubleshooting” on page 51.
43
LifeBook B Series – Section Four
PS/2 Mouse Port
LAN (RJ-45) Port
Parallel Port
External Monitor Port
Serial Port
External Floppy Disk Drive Port
DC Power Jack
Figure 4-9 Port Replicator rear panel
Port Replicator
Your LifeBook comes with a Port Replicator. The Port
Replicator extends the functionality of your LifeBook by
providing ports to connect PS/2 devices, a parallel
device, a serial device, and an external floppy disk drive.
The Port Replicator connects to the rear panel of your
LifeBook. See “Device Ports” on page 46.
REAR PANEL COMPONENTS
Following is a brief description of your Port Replicator’s
rear panel components.
External Floppy Disk Drive Port
The external floppy disk drive port allows you to attach
an optional external floppy disk drive. Note that if you
are connecting a USB floppy disk drive, you must use
the USB port on the system. (Figure 4-9)
PS/2 Mouse Port
The PS/2 mouse port allows you to connect an external
PS/2 Mouse. (Figure 4-9)
LAN (RJ-45) Port
The LAN port allows you to connect a LAN to the Port
Replicator. Note that when the system is attached to the
Port Replicator, the LAN Port on the Port Replicator
should be used, not the LAN Port on the system.
Serial Port
The serial port allows you to connect serial (RS-232C)
devices. (This is also sometimes referred to as a COMM
port.) (Figure 4-9)
DC Power Jack
The DC power jack allows you to plug in the AC adapter
to power your LifeBook and charge the internal Lithium
ion battery.
Parallel Port
The parallel port allows you to connect parallel devices.
(This is also sometimes referred to as an LPT port.)
(Figure 4-9)
44
External Monitor Port
The external monitor port allows you to connect an
external VGA or SVGA monitor. Note that if a Port
Replicator is attached, you must use the external
monitor port on the Port Replicator. (Figure 4-9)
User Installable Features
Port Replicator
Release Latch
Docking Port
Figure 4-10 Port Replicator front panel
FRONT PANEL COMPONENTS
Following is a brief description of your Port Replicator’s
front panel components
Docking Port
The docking port connects the Port Replicator to your
LifeBook. (Figure 4-10)
Port Replicator Release Latch
Pull the Port Replicator Release latch away from the Port
Replicator to remove the Port Replicator from your LifeBook. (Figure 4-10)
Figure 4-12 Unlatching the Port Replicator
DETACHING THE PORT REPLICATOR
ATTACHING THE PORT REPLICATOR
To attach the Port Replicator follow these easy steps:
1. Power off your LifeBook.
2. Align the Port Replicator connector on the bottom
of your LifeBook with the connector on the
Port Replicator and push together at the two
corners. (Figure 4-11)
To detach the Port Replicator follow these easy steps:
1. Power off your LifeBook.
2. Pull the Port Replicator’s release latch away from the
Port Replcator to release it from your LifeBook.
(Figure 4-12)
3. Pull away the Port Replicator to detach it from
your LifeBook. (Figure 4-13)
Figure 4-13 Removing the Port Replicator
Figure 4-11 Attaching the Port Replicator
45
!
LifeBook B Series – Section Four
Device Ports
Your LifeBook and Port Replicator come equipped with
multiple ports to which you can connect an external
device including: disk drives, keyboards, modems,
printers, etc.
MODEM (RJ-11) TELEPHONE PORT
The modem (RJ-11) telephone port is used for an
internal modem. To connect the telephone cable follow
these easy steps: (See figure 2-6 on page 10 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Plug the other end of the telephone cable into a
telephone outlet.
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Plug the other end of the cable into a LAN outlet.
PARALLEL PORT
The parallel port, or LPT port, located on the Port Replicator allows you to connect parallel devices, such as a
printer to your LifeBook. In order to connect a parallel
interface device follow these easy steps: (See figure 4-9 on
page 44 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Tighten the two hold-down screws, located on
each end of the connector.
SERIAL PORT
WARNING
The internal modem is not intended for use with Digital
PBX systems. Do not connect the internal modem to a
Digital PBX as it may cause serious damage to the
internal modem or your entire LifeBook. Consult your
PBX manufacturer’s documentation for details. Some
hotels have Digital PBX systems. Be sure to find out
BEFORE you connect your modem.
CAUTIONS
■
■
The internal modem is designed to the ITU-T V.90
standard. Its maximum speed of 53000bps is the
highest allowed by FCC, and its actual connection
rate depends on the line conditions. The maximum
speed is 33600bps at upload.
The internal modem on all LifeBooks from Fujitsu PC
Corporation are certified for use in the United States
and Canada.
The serial port, or COMM port, located on the Port
Replicator allows you to connect serial devices, such as
printers or scanners. In order to connect a
serial interface device follow these easy steps:
(See figure 4-9 on page 44 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Tighten the two hold-down screws, located on each
end of the connector.
PS/2 PORT
The PS/2 port located on the Port Replicator allows
you to connect an external keyboard, and/or numeric
keypad and mouse. In order to connect a PS/2 interface
device follow these easy steps: (See figure 4-9 on page 44
for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
INTERNAL LAN (RJ-45) PORT
The internal LAN (RJ-45) port is used for an internal
Fast Ethernet (10/100 Base-T/Tx) connection. If your
LifeBook has been configured with internal LAN
capability you will need to configure your LifeBook
to work with your particular network. (Please refer to
your network administrator for information on your
network configuration.) To connect the LAN cable
follow these easy steps: (See figure 2-6 on page 10 for location)
POINT
Note that the Port Replicator is designed to cover the
LAN port located on the system. This design ensures
that the LAN port on the Port Replicator is the only one
used when the Port Replicator is installed.
46
POINT
A mouse, keyboard, or keypad may be installed and
automatically recognized by your LifeBook without
restarting or changing setups.
POINT
The use of two PS/2 devices simultaneously from the
port requires a PS/2 splitter.
DOCKING PORT
The docking port is used for the connection of your LifeBook to an optional port replicator or docking station.
In order to connect your LifeBook to one of these
devices follow the instructions that came with your
docking port. (See figure 2-8 on page 12 for location)
"
User Installable Features
EXTERNAL FLOPPY DISK DRIVE PORT
The external floppy disk drive port is used for attaching
an optional external floppy disk drive. In order to
connect an external floppy disk drive to your LifeBook
follow the instructions that came with your external
floppy disk drive. (See figure 4-9 on page 44 for location)
CAUTION
Be careful not to scratch the infrared port lens.
Scratches, dirt, or other surface marks can
degrade operation.
POINT
POINT
Although there is a USB port on the system that will
accommodate a floppy disk drive, and a standard floppy
disk drive connector on the Port Replicator, only one
drive should be connected at any time.
With Windows 98 Second Edition, you can use the
Infrared Recipient application for infrared file transfers.
LapLink Professional software can also be used
for infrared file transfers.
MICROPHONE JACK
The Universal Serial Bus port (USB) allows you to
connect USB devices such as external game pads,
pointing devices, keyboards and/or speakers. In order
to connect a USB device follow these easy steps: (See
figure 2-7 on page 11 for location)
The microphone jack allows you to connect an external
mono microphone. Your microphone must be equipped
with a 1/8"(3.5 mm) mono mini-plug in order to fit into
the microphone jack of your LifeBook. In order to
connect a microphone follow these easy steps: (See
figure 2-7 on page 11 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
UNIVERSAL SERIAL BUS PORT
POINT
Due to the ongoing changes in USB technology
and standards, not all USB devices and/or drivers
are guaranteed to work.
INFRARED PORT
HEADPHONE JACK
The headphone jack allows you to connect headphones
or powered external speakers to your LifeBook. Your
headphones or speakers must be equipped with a 1/8"
(3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: (See figure 27 on page 11 for location)
The Infrared IrDA 1.1 (4Mbps) port allows for wireless
data transfer between your LifeBook and other IrDAcompatible devices, such as another computer or a
printer, without the use of a cable. (See figure 2-6 on
page 10 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
It is important to keep in mind that while carrying out
this form of communication, both devices must be
placed so their infrared ports are directly facing each
other without obstruction. The devices must also be
separated by at least 6" but no more than 36" for
maximum performance.
If you plug headphones into the headphone jack, the
built-in stereo speakers will be disabled.
The following conditions may interfere with infrared
communications:
■
■
A television, radio remote control unit, or a wireless
headphone is being used nearby.
Direct sunlight, fluorescent light, or incandescent light
shines directly on the port.
POINT
EXTERNAL MONITOR PORT
The external monitor port allows you to connect an
external VGA or SVGA monitor. In order to connect an
external monitor follow these easy steps: (See figure 2-7
on page 11 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Tighten the two hold-down screws, located on
each end of the connector.
CAUTION
Do not move either device while communication is
active as it may interrupt data transmission.
47
#
LifeBook B Series – Section Four
CAUTION
Pressing the [Fn] + [F10] keys allows you to change
your selection of where to send your display video. Each
time you press the key combination, you will
step to the next choice, starting with the built-in display
panel only, moving to the external monitor only, finally
moving to both the built-in display panel and an
external monitor.
48
5
Troubleshooting
49
LifeBook B Series – Section Five
50
Tro ubleshoo ting
Troubleshooting
Your LifeBook is sturdy and subject to few problems in
the field. However, you may encounter simple setup or
operating problems that you can solve on the spot, or
problems with peripheral devices, that you can solve by
replacing the device. The information in this section
helps you isolate and resolve some of these straightforward problems and identify failures that require service.
sentative can provide you with the fastest possible solution:
■
■
■
■
■
■
■
■
IDENTIFYING THE PROBLEM
If you encounter a problem, go through the following
procedure before pursuing complex troubleshooting:
1. Turn off your LifeBook.
2. Make sure the AC adapter is plugged into your LifeBook and to an active AC power source.
3. Make sure that any card installed in the PC Card slot
is seated properly. You can also remove the card
from the slot, thus eliminating it as a possible cause
of failure.
4. Make sure that any devices connected to the external
connectors are plugged in properly. You can also
disconnect such devices, thus eliminating them as
possible causes of failure.
5. Turn on your LifeBook. Make sure it has been off at
least 10 seconds before you turn it on.
6. Go through the boot sequence.
7. If the problem has not been resolved, refer to the
Troubleshooting Table, that follows, for more
detailed troubleshooting information.
POINT
If you keep notes about what you have tried, your
support representative may be able to help you
more quickly by giving additional suggestions
over the phone.
Product name
Product configuration number
Product serial number
Purchase date
Conditions under which the problem occurred
Any error messages that have occurred
Hardware configuration
Type of device connected, if any
See the Configuration Label on the bottom of your
LifeBook for configuration and serial numbers. (See
figure 2-8 on page 12 for location)
SPECIFIC PROBLEMS
Using PC-Doctor 2000
(with Windows 98 Second Edition only)
PC-Doctor 2000 is a diagnostic program by PCDoctor.com, Inc. which comes pre-installed on your
LifeBook. If you are an experienced computer user you
may find it useful, however, it is intended primarily to
help your Fujitsu support representative better serve
you.
Using the Troubleshooting Table
When you have problems with your LifeBook, try to
find the symptoms under the Problem column of the
troubleshooting table for the feature giving you difficulty.
You will find a description of common causes for that
symptom under the column Possible Cause and what, if
anything, you can do to correct the condition under
Possible Solutions. All possible causes or solutions may
not apply to your LifeBook.
CAUTION
Do not return a failed LifeBook to your supplier until
you have talked to a support representative.
8. If you have tried the solutions suggested in the Troubleshooting Table without success, contact your
support representative:
Toll free: 1-800-8FUJITSU (1-800-838-5487)
Fax: 1-901-259-5700
E-mail: [email protected]
Web site: http://www.fujitsupc.com.
Before you place the call, you should have the following
information ready so that the customer support repre-
51
LifeBook B Series – Section Five
TROUBLESHOOTING TABLE
Problem
Page
Audio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 52
Docking Problems . . . . . . . . . . . . . . . . . . . . . . . . page 52
Floppy Disk Drive Problems . . . . . . . . . . . . . . . . page 52
Hard Drive Problems . . . . . . . . . . . . . . . . . . . . . . page 53
Keyboard or Mouse Problems. . . . . . . . . . . . . . . page 53
Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . page 53
Problem
Problem
Page
Modem Problems. . . . . . . . . . . . . . . . . . . . . . . . . page 54
Parallel, Serial and USB Device Problems . . . . . page 54
PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 54
Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 55
Shutdown and Startup Problems . . . . . . . . . . . . page 57
Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 58
Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 60
Possible Cause
Possible Solutions
Audio Problems
There is no sound coming
from the built-in speakers.
The volume is turned too low.
Adjust the volume control on your LifeBook.
The software volume control is
set too low.
Adjust the sound volume control settings in your
software, operating system and applications.
Headphones are plugged into
your LifeBook.
Plugging in headphones disables the built-in
speakers, remove the headphones.
BIOS audio settings
are incorrect.
Set the BIOS setup utility to the default values
within the Multimedia Device Configuration menu.
See “BIOS Setup Utility” on page 29.
Software driver is not configured correctly.
Refer to your application and operating system
documentation for help.
Sound could have been muted
with function keys.
Press [F3] while holding the [Fn] key to toggle the
sound on and off.
Port Replicator AC adapter is
not plugged in.
Provide power to the Port Replicator.
LifeBook is not properly seated
in the Port Replicator.
Remove and re-dock your LifeBook.
You tried to write to a write
protected floppy disk.
Eject the floppy disk and set it to write enable.
See “Preparing a Disk for Use” on page 39.
Floppy disk is not
loaded correctly.
Eject floppy disk, check orientation and re-insert.
See “Ejecting a Disk” on page 39.
BIOS setup utility states
Revise the setup utility Main menu settings to
enable Diskette Controller. See “BIOS Setup Utility”
on page 29.
Port Replicator Problems
LifeBook does not turn
on when installed in
Port Replicator
Floppy Disk Drive Problems
You cannot access your
floppy disk.
You cannot access your
floppy disk. (continued)
52
Diskette Controller:
Disabled.
The floppy disk drive may not
be properly installed.
Remove and re-install your floppy disk drive.
Security is set to protect access
to floppy disk data.
Verify your password and security settings.
Tro ubleshoo ting
Problem
Possible Cause
Possible Solutions
Hard Drive Problems
You cannot access your
hard drive.
The setup utility is incorrectly
set for your internal (Primary
Master) or optional second
hard drive (Primary Slave).
Revise BIOS settings to set both Primary Master
and Primary Slave correctly. See “BIOS Setup
Utility” on page 29.
The wrong drive designator
was used by an application
when a bootable CD-ROM was
used to start the LifeBook.
Verify drive designator used by application is in
use by the operating system. When the operating
system is booted from a CD, drive designations
are automatically adjusted.
Security is set so your operating system cannot be started
without a password.
Verify your password and security settings.
Keyboard or Mouse Problems
The built-in keyboard does
not seem to work.
You have installed an
external keyboard or
mouse, and it does not
seem to work.
You have connected an
external keyboard or a
mouse and it seems to be
locking up the system.
The LifeBook has gone into
Suspend mode.
Push the Suspend/Resume button.
Your application has locked
out your keyboard.
Try to use your integrated pointing device to restart
your system. If this fails, turn your LifeBook off
using the power switch, wait 10 seconds or more,
and then turn it back on.
Your external device is not
properly installed.
Re-install your device. See “Device Ports” on page 46.
Your operating system
software is not setup with
the correct software driver
for that device.
Check your device and operating system documentation and activate the proper driver.
Your mouse or keyboard is
connected to the wrong PS/2
port on the LANdock.
Plug the mouse into the PS/2 Mouse port and
the external keyboard or numeric key pad into the
PS/2 Keyboard port. See “PS/2 Port” on page 46.
Your operating system
software is not setup with
the correct software driver
for that device.
Check your device and operating system
documentation and activate the proper driver.
Your system has crashed.
Try to restart your LifeBook. If that fails, turn off the
power using the power switch, wait at least 10
seconds, and then power on.
Your memory upgrade module
is not properly installed.
Remove and re-install your memory upgrade
module. See “Memory Upgrade Module” on page 42.
You have a memory failure.
Check for Power On Self Test (POST) messages.
See “Power On Self Test Messages” on page 61.
Memory Problems
Your Power On screen,
or Main menu of the
BIOS setup utility information, does not show
the correct amount of
installed memory.
53
LifeBook B Series – Section Five
Problem
Possible Cause
Possible Solutions
Modem Problems
Messages about modem
operation.
Messages about modem
operation are generated
by whichever modem
application is in use.
See your application software documentation for
additional information.
Parallel, Serial, and USB Device Problems
You have installed a parallel
port device, a serial port
device or a USB device.
Your LifeBook does not
recognize the device, or the
device does not seem to
work properly.
The device is not
properly installed.
Remove and re-install the device. See “Device Ports”
on page 46.
The device may have been
installed while an application
was running, so your LifeBook
is not aware of its installation.
Close the application and restart your LifeBook.
Your software may not
have the correct software
driver active.
See your software documentation and activate the
correct driver.
You may have the wrong
I/O address selected for
your device.
See your device documentation and software documentation to determine the required I/O address.
Change the settings in the BIOS setup utility. See
“BIOS Setup Utility” on page 29.
Your device and another
device are assigned the same
I/O address.
Check all I/O addresses located within the BIOS
setup utility and any other installed hardware or
software to make sure there are no duplications.
Parallel port is set to
output only.
Check parallel port setting in the BIOS and set to
bi-directional or ECP.
The card is not
properly installed.
Remove and re-install the card. See “PC Cards” on
page 40.
The card may have been
installed while an application
was running, so your LifeBook
is not aware of its installation.
Close the application and restart your LifeBook.
Your software may not
have the correct software
driver active.
See your software documentation and activate the
correct driver.
You may have the wrong
I/O address selected for your
PC Card device.
See your PC Card documentation to determine
the required I/O address. Change the settings in
the BIOS. See “BIOS Setup Utility” on page 29.
Your PC Card device and
another device are assigned the
same I/O address.
Check all I/O addresses located within the BIOS
setup utility and any other installed hardware or
software to make sure there are no duplications.
PC Card Problems
A card inserted in the PC
Card slot does not work or
is locking up the system.
54
Tro ubleshoo ting
Problem
Possible Cause
Possible Solutions
Power Failures
You turn on your
LifeBook and nothing
seems to happen.
The installed primary
battery is completely
discharged, there is no
optional second battery
installed or there is no
Power adapter (AC or Auto/
Airline) installed.
Check the Status Indicator Panel to determine the
presence and condition of the batteries. See “Status
Indicator Panel” on page 13. Install a charged
battery or a Power adapter.
The primary battery is
installed but is faulty.
Use the Status Indicator Panel to verify the presence
and condition of the batteries. See “Status Indicator
Panel” on page 13. If a battery is indicating a short,
remove that battery and operate from another
power source or replace that battery.
The battery or batteries are low. Check the Status Indicator Panel to determine the
presence and condition of the batteries. See “Status
Indicator Panel” on page 13. Use a Power adapter to
operate until a battery is charged or install a charged
battery.
You turn on your LifeBook
and nothing seems to
happen. (continued)
The power adapter (AC or
auto/airline) is not plugged
in properly.
Verify that your adapter is connected correctly. See
“Power Sources” on page 27.
The Power adapter (AC
or auto/airline) has no
power from the AC outlet,
airplane seat jack, or the car’s
cigarette lighter.
Move the AC cord to a different outlet, check for
a line switch or tripped circuit breaker for the AC
outlet. If you are using an auto/airline adapter in
a car make sure the ignition switch is in the On or
Accessories position.
The Power adapter (AC or
auto/airline) is faulty.
Try a different Power adapter or install a charged
optional second battery.
Power switch is not in the
On position.
Slide your power switch firmly to the Off position,
pause 10 seconds or more and then firmly to the
On position.
55
!
LifeBook B Series – Section Five
Problem
Your LifeBook turns off
all by itself.
Your LifeBook will not
work on battery alone.
56
Possible Cause
Possible Solutions
The power management
parameters are set for auto
timeouts which are too short
for your operating needs.
Press any button on the keyboard, or move the
mouse to restore operation. If that fails, push the
Suspend/Resume button. Check your power
management settings, or close your applications
and go to the Power Savings menu of the setup
utility to adjust the timeout values to better suit
your operation needs.
You are operating on battery
power only and have ignored a
low battery alarm until the
batteries are all at the dead
battery state and your machine
has gone into Dead Battery
Suspend mode.
Install a power adapter and then push the Suspend/
Resume button. See “Power Sources” on page 27.
You have a battery failure.
Verify the condition of the batteries using the
Status Indicator panel, and replace or remove
any batteries that are shorted. See “Status Indicator
Panel” on page 13.
Your power adapter has failed
or lost its power source.
Make sure the adapter is plugged in and the outlet
has power.
The installed batteries
are dead.
Replace the battery with a charged one or install
a Power adapter.
No batteries are installed.
Install a charged battery.
The batteries are
improperly installed.
Verify that the batteries are properly connected
by re-installing them.
Your installed batteries
are faulty.
Verify the condition of the batteries using the
Status Indicator panel and replace or remove
any batteries that are shorted. See “Status Indicator
Panel” on page 13.
"
Tro ubleshoo ting
Problem
The batteries seem to
discharge too quickly.
Possible Cause
Possible Solutions
You are running an application
that uses a great deal of power
due to frequent hard drive
access or CD-ROM access, use
of a modem card or a LAN PC
card.
Use both the primary battery and an optional
second battery and/or use a power adapter for this
application when at all possible.
The power savings features
may be disabled.
Check the power management and/or setup utility
settings in the Power Savings menu and adjust
according to your operating needs.
The brightness is turned all
the way up.
Turn down the brightness adjustment. The higher
the brightness the more power your display uses.
The batteries are very old.
Replace the batteries.
The batteries have been
exposed to high temperatures.
Replace the batteries.
The batteries are too hot
or too cold.
Restore the LifeBook to normal operating temperature. The Charging icon on the Status Indicator
panel will flash when the battery is outside its
operating range.
Shutdown and Startup Problems
The Suspend/Resume
button does not work.
The system powers up, and
displays power on information, but fails to load the
operating system.
The system powers up, and
displays power on information, but fails to load the
operating system.
(continued)
The Suspend/Resume button
is disabled from the Advanced
submenu of the Power menu
of the setup utility.
Enable the button from the setup utility.
You did not hold the button
in long enough.
Hold the button longer. This may need to be a few
seconds if your application is preventing the CPU
from checking for button pushes.
There may be a conflict with
the application software.
Close all applications and try the button again.
The boot sequence settings
of the setup utility are not
compatible with your
configuration.
Set the operating source by pressing the [ESC] key
while the Fujitsu logo is on screen or use the [F2]
key and enter the setup utility and adjust the source
settings from the Boot menu. See “BIOS Setup
Utility” on page 29.
You have a secured system
requiring a password to load
your operating system.
Make sure you have the right password. Enter the
setup utility and verify the Security settings and
modify them as accordingly. See “BIOS Setup
Utility” on page 29.
Internal hard drive was
not detected.
Use the BIOS setup utility or Primary Master
submenu, located within the Main menu, to try to
auto detect the internal hard drive.
57
#
LifeBook B Series – Section Five
Problem
Possible Cause
Possible Solutions
An error message is
displayed on the screen
during the LifeBook
(boot) sequence.
Power On Self Test (POST) has
detected a problem.
See the Power On Self Test (POST) messages to
determine the meaning and severity of the problem.
Not all messages are errors; some are simply status
indicators. See “Power On Self Test Messages” on
page 61.
Your system display won’t
turn on when the system is
turned on or when the
system has resumed.
The system may be passwordprotected.
Check the status indicator panel to verify that the
Security icon is blinking. If it is blinking, enter your
password.
Your LifeBook appears to
change setup parameters
when you start it.
BIOS setup changes were not
saved when you made them
and exited the BIOS setup
utility returning it to
previous settings.
Make sure you select Save Changes And Exit when
exiting the BIOS setup utility.
The BIOS CMOS back-up
battery has failed.
Contact your support representative for repairs.
This is not a user serviceable part but has a normal
life of 3 to 5 years.
Something is pushing on the
Closed Cover switch.
Clear the Closed Cover switch. (See figure 2-5 on
page 8 for location)
The LifeBook is set for an
external monitor only.
Pressing [F10] while holding down the [FN] key
allows you to change your selection of where to
send your display video. Each time you press the
combination of keys you will step to the next
choice. The choices, in order are: built-in display
only, external monitor only, both built-in display
and external monitor.
The angle of the display
and the brightness settings
are not adequate for your
lighting conditions.
Move the display and the brightness control until
you have adequate visibility.
The power management timeouts may be set for very short
intervals and you failed to
notice the display come on
and go off again.
Press any button the keyboard, or move the mouse
to restore operation. If that fails, push the Suspend/
Resume button. (The display may be shut off by
Standy mode, Auto Suspend or Video Timeout)
The LifeBook turned
on with a series of beeps
and your built-in display
is blank.
Power On Self Test (POST)
has detected a failure which
does not allow the display
to operate.
Contact your support representative.
Your system display won’t
turn on when the system is
turned on or when the
system has resumed.
The system may be passwordprotected.
Check the status indicator panel to verify that the
Security icon is blinking. If it is blinking, enter your
password.
Video Problems
The built-in display is
blank when you turn on
your LifeBook.
58
Tro ubleshoo ting
Problem
The display goes blank by
itself after you have been
using it.
Possible Cause
Possible Solutions
The LifeBook has gone into
Video Timeout, Standby
Mode, Suspend Mode or Saveto-Disk Mode because you
have not used it for a period of
time.
Press any button on the keyboard, or move the
mouse to restore operation. If that fails, push the
Suspend/Resume button. Check your power
management settings, or close your applications
and go to the Power Savings menu of the setup
utility to adjust the timeout values to better suit
your operation needs. See “BIOS Setup Utility” on
page 29.
Something is pushing on the
Closed Cover switch.
Check the Closed Cover switch. (See figure 2-5 on
page 8 for location)
The power management timeouts may be set for very short
intervals and you failed to
notice the display come on
and go off again.
Press any button on the keyboard, or move the mouse
to restore operation. If that fails, push the Suspend/
Resume button. (The display may be shut off by
Standby Mode, Auto Suspend or Video Timeout)
The Built-in Display does
not close.
A foreign object, such as a
paper clip, is stuck between the
display and the keyboard.
Remove all foreign objects from the keyboard.
The Built-in Display has
bright or dark spots.
If the spots are very tiny and
few in number, this is normal
for a large LCD display.
This is normal; do nothing.
If the spots are numerous or
large enough to interfere with
your operation needs.
Display is faulty; contact your support representative.
The application display
uses only a portion of your
screen and is surrounded
by a dark frame.
You are running an application
that does not support 800 x
600/1024 x 768 pixel resolution
display and display compression is enabled.
Display compression gives a clearer but smaller
display for applications that do not support 800 x
600/1024 x 768 pixel resolution. You can fill the
screen but have less resolution by changing your
display compression setting, (See the Video Features
submenu, located within the Advanced menu of the
BIOS. See “BIOS Setup Utility” on page 29.
The Display is dark when
on battery power.
The BatteryAid default is set
on low brightness to
conserve power.
Press [FN] + [F7] to increase brightness or doubleclick on BatteryAid battery gauge and adjust Power
Control under battery settings.
You have connected an
external monitor and
it does not display
any information.
Your BIOS setup is not set to
enable your external monitor.
Try toggling the video destination by pressing [FN]
and [F10] together, or check your BIOS setup and
enable your external monitor. (See the Video
Features submenu, located within the Advanced
Menu of the BIOS. See “BIOS Setup Utility” on
page 29.
Your external monitor is not
properly installed.
Reinstall your device. See “External Monitor Port” on
page 47.
Your operating system software is not setup with the
correct software driver for
that device.
Check your device and operating system
documentation and activate the proper driver.
59
!
LifeBook B Series – Section Five
Problem
You have connected an
external monitor and it
does not come on.
Possible Cause
Possible Solutions
Your external monitor
is not compatible with
your LifeBook.
See your monitor documentation and the
External Monitor Support portions of the
Specifications section. See “Specifications” on
page 73.
Application software often
has its own set of error
message displays.
See your application manual and help displays
screens for more information. Not all messages are
errors some may simply be status.
Miscellaneous Problems
An error message is
displayed on the screen
during the operation of
an application.
60
!
Tro ubleshoo ting
POWER ON SELF TEST MESSAGES
The following is an alphabetic list of error-and-status
messages that Phoenix BIOS and/or your operating
system can generate and an explanation of each message.
Error messages are marked with an *. If an error
message is displayed that is not in this list, write it down
and check your operating system documentation both
on screen and in the manual. If you can find no reference
to the message and its meaning is not clear, contact
your support representative for assistance.
nnnn Cache SRAM Passed
Where nnnn is the amount of system cache in kilobytes
successfully tested by the Power On Self Test. (This can
only appear if you have an SRAM PC Card installed.)
*Diskette drive A error or Diskette drive B error
Drive A: or B: is present but fails the BIOS Power On Self
Test diskette tests. Check to see that the drive is defined
with the proper diskette type in the Setup Utility, See
“BIOS Setup Utility” on page 29. and that the diskette
drive is installed correctly. If the disk drive is properly
defined and installed, avoid using it and contact your
support representative.
*Extended RAM Failed at offset: nnnn
Extended memory not working or not configured properly. If you have an installed memory upgrade module,
verify that the module is properly installed. If it is properly installed, you may want to check your Windows
Setup to be sure it is not using unavailable memory
until you can contact your support representative.
*Incorrect Drive A type – run SETUP
Type of floppy drive A: not correctly identified in Setup.
This means that the floppy disk drive type identified in
your setup utility does not agree with the type detected
by the Power On Self Test. Run the setup utility to
correct the inconsistency.
*Incorrect Drive B type – run SETUP
Type of floppy drive B: not correctly identified in Setup.
This means that the floppy disk drive type identified in
your setup utility does not agree with the type detected
by the Power On Self Test. Run the setup utility to
correct the inconsistency.
*Invalid NVRAM media type
Problem with NVRAM access. In the unlikely case that
you see this message you may have some display problems. You can continue operating but should contact
your support representative for more information.
*Keyboard controller error
The keyboard controller test failed. You may have to
replace your keyboard or keyboard controller but may
be able to use an external keyboard until then. Contact
your support representative.
*Keyboard error
Keyboard not working. You may have to replace your
keyboard or keyboard controller but may be able to
use an external keyboard until then. Contact your
support representative.
nnnn Extended RAM Passed
Where nnnn is the amount of memory in kilobytes
successfully tested.
*Keyboard error nn
BIOS discovered a stuck key and displays the scan code
for the stuck key. You may have to replace your keyboard
but may be able to use an external keyboard until then.
Contact your support representative.
*Failing Bits: nnnn The hex number nnnn
This is a map of the bits at the memory address (in
System, Extended, or Shadow memory) which failed the
memory test. Each 1 (one) in the map indicates a failed
bit. This is a serious fault that may cause you to lose data
if you continue. Contact your support representative.
*Monitor type does not match CMOS – Run SETUP
Monitor type not correctly identified in Setup. This
error probably means your BIOS is corrupted, run the
setup utility and set all settings to the default conditions.
If you still get this error, contact your support representative.
*Fixed Disk x Failure or Fixed Disk Controller
Failure (where x = 1-4)
The fixed disk is not working or not configured properly. This may mean that the hard drive type identified
in your setup utility does not agree with the type
detected by the Power On Self Test. Run the setup utility
to check for the hard drive type settings and correct
them if necessary. If the settings are OK and the message
appears when you restart the system, there may be a
serious fault which might cause you to lose data if you
continue. Contact your support representative.
*Operating system not found
Operating system cannot be located on either drive A: or
drive C: Enter the setup utility and see if both the fixed
disk, and drive A: are properly identified and that the
boot sequence is set correctly. Unless you have changed
your installation greatly, the operating system should be
on drive C:. If the setup utility is correctly set, your hard
drive may be corrupted and your system may have to be
re-installed from your back up media.
*Parity Check 1 nnnn
Parity error found in the system bus. BIOS attempts to
locate the address and display it on the screen. If it
61
!
LifeBook B Series – Section Five
cannot locate the address, it displays????. This is a
potentially data destroying failure. Contact your
support representative.
*Parity Check 2 nnnn
Parity error found in the I/O bus. BIOS attempts to
locate the address and display it on the screen. If it
cannot locate the address, it displays ????. This is a
potentially data destroying failure. Contact your
support representative.
*System RAM Failed at offset: nnnn
System memory failed at offset nnnn of in the 64k block
at which the error was detected. This means that there is
a fault in your built-in memory. If you continue to
operate, you risk corrupting your data. Contact your
support representative for repairs.
nnnn System RAM Passed
Where nnnn is the amount of system memory in
kilobytes successfully tested.
*Press <F1> to resume, <F2> to SETUP
Displayed after any recoverable error message. Press
the [F1] key to continue the boot process or the [F2]
key to enter Setup and change any settings.
*System timer error
The timer test failed. The main clock that operates the
computer is faulty. Requires repair of system board.
Contact your support representative for repairs.
*Previous boot incomplete –
Default configuration used
Previous Power On Self Test did not complete successfully. The Power On Self Test will load default values and
offer to run Setup. If the previous failure was caused by
incorrect values and they are not corrected, the next
boot will likely fail also. If using the default settings does
not allow you to complete a successful boot sequence,
you should turn off the power with the Power Switch
and contact your support representative.
UMB upper limit segment address: nnnn
Displays the address of the upper limit of Upper
Memory Blocks, indicating released segments of the
BIOS memory which may be reclaimed by a virtual
memory manager.
*Real time clock error
Real-time clock fails BIOS test. May require board repair.
Contact your support representative.
*Shadow RAM Failed at offset: nnnn
Shadow RAM failed at offset nnnn of the 64k block at
which the error was detected. You are risking data
corruption if you continue. Contact your support representative.
Video BIOS shadowed
Video BIOS successfully copied to shadow RAM.
MODEM RESULT CODES
The operating system and application software that is
factory installed detects the modem characteristics and
provides the necessary command strings to operate the
modem. The internal modem operation is controlled by
generic AT commands from the operating system and
application software. The standard long form result
codes may, in some cases, be displayed on your screen to
keep you informed of the actions of your modem. The
operating system and application software may suppress
display of the result codes.
nnnn Shadow RAM Passed
Where nnnn is the amount of shadow RAM in kilobytes
successfully tested.
Examples of result codes are:
*System battery is dead – Replace and run SETUP
The BIOS CMOS RAM memory hold up battery is dead.
This is part of your BIOS and is a board mounted
battery which requires a support representative to
change. You can continue operating but you will have to
use setup utility default values or reconfigure your setup
utility every time you turn off your LifeBook. This
battery has an expected life of 2 to 3 years.
■
System BIOS shadowed
System BIOS copied to shadow RAM.
*System CMOS checksum bad – run SETUP
BIOS CMOS RAM has been corrupted or modified
incorrectly, perhaps by an application program that
changes data stored in BIOS memory. Run Setup and
reconfigure the system.
62
■
■
■
■
■
■
■
■
OK
NO CARRIER
NO DIALTONE
CONNECT 53000 (Connection complete
at 53,000 bps.)
ERROR
FAX
RING (This means an incoming call.)
BUSY
NO ANSWER
When using the internal modem with applications
that are not factory installed refer to the
application documentation.
!
Tro ublesho oting
Restoring Your
Pre-installed Software
Your system has been loaded with a valuable utility that
allows you to restore your LifeBook disk drive contents
as they were originally shipped from the factory. Most
often this is necessary if files or software programs (only
those files/programs that came pre-installed) become
corrupt or accidentally erased.
DRIVE IMAGE SPECIAL EDITION (DISE)
PowerQuest Drive Image Special Edition (DISE)
provides a way to restore your computer if you experience a hard disk crash or other system failure. Fujitsu has
used DISE to create an image of everything that was
installed on the computer at the time you purchased it.
The image is saved on a separate partition on the hard
disk. You can use DISE to restore the factory image and
return your computer to the state in which it shipped
from Fujitsu.
Although it is not necessary, you can use DISE to store
an additional image file that you create. For example, if
you install several applications and save data files on
your hard disk, you can create a new image file that
includes them and then save that image file on the hard
disk. Then, in the event of a hard disk failure, you can
restore the image that includes the applications and data
files you use.
Fujitsu recommends that you create a DISE disk as a
"rescue disk." If your computer fails, you can boot and
run DISE from the rescue disk.
POINT
Using the DISE feature will reduce the amount of usable
disk space on your hard disk drive.
Creating Drive Image SE Diskettes
Note: You can use a DISE disk to boot your machine and
run DISE if your machine is unbootable or if you do not
have access to Windows.
Insert a formatted floppy disk in your machine.
From the Drive Image Special Edition main window,
click Options > Create Drive Image SE Diskette.
Running DISE from Diskettes
1. Insert the Drive Image SE Disk 1 in the floppy drive.
2. Reboot your computer.
3. Insert Disk 2, type DISE, then press <Enter>.
Creating a Backup Image
You can create a backup image of your C:\ drive at any
time. The C:\ partition must be a FAT, FAT32, or NTFS
partition, and it must be directly before the backup
partition on your hard disk.
1. At the Drive Image Special Edition main screen,
click Options> Create New Backup.
There is also a button on the main DISE screen that
performs the same function.
2. You will be prompted to type a password. Type a
password (or leave the password fields blank), then
click OK. DISE displays a warning that it must go to
DOS to create the image.
3. Click Yes.
DISE creates an image file in the backup partition. If
you created a backup image previously, the new
image overwrites the old one.
Enlarging the Backup Partition
If there is not enough unused space in the backup partition on your hard disk, DISE will resize the partition.
DISE will display the minimum, maximum, and recommended sizes for the backup partition. You choose the
size you want.
DISE takes the space from the FAT, FAT32, or NTFS
partition that you are backing up. If there is not enough
unused space in that partition to take, you will not be
able to resize the backup partition and create an image
file. You can delete files from the FAT, FAT32, or NTFS
partition to create more unused space on the hard disk.
Restoring a Backup Image
You can restore either a factory image or a backup image
you created. Be aware that restoring a backup image will
replace the contents of the C:\ partition with the image
you restore.
1. Disable virus protection software in the BIOS. If
virus protection software is enabled, DISE will hang.
2. From the DISE main window, click Options >
Restore Backup to restore an image you created, or
click Options > Restore Factory Backup to restore
the factory image.
DISE shuts down to DOS and restores the image file.
DRIVERS AND APPLICATIONS RESTORE CD
The Drivers and Application CD can be used to selectively re-install drivers and/or applications that may have
been un-installed or corrupted. Please refer to installation instructions located in readme.txt file on the
Drivers and Applications Restore CD.
POINT
Look for and open files with the extensions.DOC, .PDF
and/or .TXT.
63
!
LifeBook B Series – Section Five
64
! 6
Care and Maintenance
65
!!
LifeBook B Series – Section Six
66
!"
Care and Maintenance
Care and Maintenance
If you use your LifeBook carefully, you will increase its
life and reliability. This section provides some tips for
looking after the LifeBook and its devices.
Cleaning your LifeBook
■
Always disconnect the power plug. (Pull the plug,
not the cord.)
■
Clean your LifeBook with a damp, lint-free cloth. Do
not use abrasives or solvents.
■
Use a soft cloth to remove dust from the screen.
Never use glass cleaners.
CAUTION
Electrical equipment may be hazardous if misused.
Operations of this product or similar products, must
always be supervised by an adult. Do not allow children
access to the interior of any electrical products and do
not permit them to handle any cables.
Storing your LifeBook
■ If storing your LifeBook for a month or longer, turn
your LifeBook off and remove all Lithium ion batteries.
■
Store your LifeBook and batteries
separately. If you store your LifeBook with a battery
installed, the battery will discharge, and battery life
will be reduced. In addition, a faulty battery might
damage your LifeBook.
■
Store your LifeBook in a cool, dry location.
Temperatures should remain between -25ºC (13ºF)
and 60ºC (140ºF).
LIFEBOOK
Caring for your LifeBook
■ Your LifeBook is a durable but sensitive electronic
device. Treat it with care.
■
Make a habit of transporting it in a suitable
carrying case.
■
Do not attempt to service the computer yourself.
Always follow installation instructions closely.
■
Keep it away from food and beverages.
■
If you accidentally spill liquid on your LifeBook:
1. Turn it off.
2. Position it so that the liquid can run out.
3. Let it dry out for 24 hours, or longer if needed.
4. If your LifeBook will not boot after it has dried
out, call your support representative.
Do not use your LifeBook in a wet environment (near
a bathtub, swimming pool).
■
■
Always use the AC adapter and batteries that are
approved for your LifeBook.
■
Avoid exposure to sand, dust and other
environmental hazards.
■
Do not expose your LifeBook to direct sunlight for
long periods of time as temperatures above
140° F (60° C) may damage your LifeBook.
■
Keep the covers closed on the connectors and slots
when they are not in use.
Do not put heavy or sharp objects on the computer.
■
■
If you are carrying your LifeBook in a briefcase, or any
other carrying case, make sure that there are no
objects in the case pressing on the lid.
■
Do not drop your LifeBook.
■
Do not touch the screen with any sharp objects.
Traveling with your LifeBook
■
Do not transport your LifeBook while it is turned on.
■
Do not check your LifeBook as baggage. Carry it with
you.
■
Never put your LifeBook through a metal detector.
Have your LifeBook hand-inspected by security personnel. You can, however, put your LifeBook through
a properly tuned X-ray machine. To avoid problems,
place your LifeBook close to the entrance of the
machine and remove it as soon as possible or have
your LifeBook hand-inspected by security personnel.
Security officials may require you to turn your LifeBook On. Make sure you have a charged battery on
hand.
■
When traveling with the hard drive removed, wrap the
drive in a non-conducting materials (cloth or paper).
If you have the drive checked by hand, be ready to
install the drive if needed. Never put your hard drive
through a metal detector. Have your hard drive handinspected by security personnel. You can however, put
your hard drive through a properly tuned X-ray
machine.
■
Take the necessary plug adapters if you're traveling
overseas. Check the following diagram to determine
which plug adapter you'll need or ask your travel
agent.
67
!#
LifeBook B Series – Section Six
Outlet Type
Location
United States, Canada,
parts of Latin America,
Japan, Korea,
the Philippines, Taiwan
Russia and the Commonwealth of Independent States
(CIS), most of Europe, parts
of Latin America, the Middle
East, parts of Africa, Hong
Kong, India, most of South
Asia
Mexico, United Kingdom,
Ireland, Malaysia, Singapore,
parts of Africa
China, Australia,
New Zealand
BATTERIES
Caring for your Batteries
■
Always handle batteries carefully.
■
■
Do not short-circuit the battery terminals (that is, do
not touch both terminals with a metal object). Do not
carry lose batteries in a pocket or purse where they
may mix with coins, keys, or other metal objects.
Doing so may cause an explosion or fire.
Do not drop, puncture, disassemble, mutilate or incinerate the battery.
■
Recharge batteries only as described in this manual
and only in ventilated areas.
■
Do not leave batteries in hot locations for more than a
day or two. Intense heat can shorten battery life.
■
Do not leave a battery in storage for longer than 6
months without recharging it.
68
Increasing Battery Life
■
Power your LifeBook through the AC or optional
auto/airline adapter whenever possible.
■
If your LifeBook is running on battery power all day,
connect it to the AC adapter overnight to recharge the
battery.
■
Keep brightness to the lowest level comfortable.
■
Set the power management for maximum battery life.
■
Put your LifeBook in Suspend mode when it is turned
on and you are not actually using it.
■
Limit your CD-ROM access.
■
Disable the Windows CD auto insert function.
■
Always use fully charged batteries.
■
Eject PCMCIA cards when not in use.
FLOPPY DISKS AND DRIVES
Caring for your Floppy Disks
■
Avoid using the floppy disks in damp and
dusty locations.
■
Never store a floppy disk near a magnet or
magnetic field.
■
Do not use a pencil or an eraser on a disk or
disk label.
■
Avoid storing the floppy disks in extremely hot or cold
locations, or in locations subject to severe temperature
changes. Store at temperatures between 50º F (10ºC)
and 125ºF (52ºC).
■
Do not touch the exposed part of the disk
behind the metal shutter.
Caring for your Floppy Disk Drive
■ To clean, wipe the floppy disk drive clean with a dry
soft cloth, or with a soft cloth dampened with water or
a solution of neutral detergent. Never use benzene,
paint thinner or other volatile material.
■
Avoid storing the floppy disk drive in extremely hot or
cold locations, or in locations subject to severe temperature changes. Store at temperatures between
50º F (10ºC) and 125ºF (52ºC).
■
Keep the floppy disk drive out of direct sunlight and
away from heating equipment.
■
Avoid storing the floppy disk drive in locations subject
to shock and vibration.
■
Never use the floppy disk drive with any liquid, metal,
or other foreign matter inside the floppy disk
drive or disk.
■
Never disassemble or dismantle your floppy disk drive.
!
Care and Maintenance
CDs
Caring for your CDs
CDs are precision devices and will function reliably if
given reasonable care.
will provide specific information, but you should
pay attention to the following points:
■
To keep out dust and dirt, store PC Cards in their
protective sleeves when they are not installed in
your LifeBook.
■
Always store your CDs in its case when it is not in use.
■
Always handle CDs by the edges and avoid touching
the surface.
■
Avoid prolonged exposure to direct sunlight or
excessive heat.
■
Avoid storing any CDs in extreme temperatures.
■
Keep the cards dry.
■
Do not bend CDs or set heavy objects on them.
■
Do not flex or bend the cards, and do not place heavy
objects on top of them.
■
Do not spill liquids on CDs.
■
Do not force cards into the slot.
■
Do not scratch CDs.
■
■
Do not put a label on CDs.
Avoid dropping cards, or subjecting them to
excessive vibration.
■
Do not get dust on CDs.
■
Never write on the label surface with a ballpoint pen
or pencil. Always use a felt pen.
■
If a CD is subjected to a sudden change in temperature, cold to warm condensation may form on the surface. Wipe the moisture off with a clean, soft, lint free
cloth and let it dry at room temperature. DO NOT use
a hair dryer or heater to dry CDs.
■
If a CD is dirty, use only a CD cleaner or wipe it with a
clean, soft, lint free cloth starting from the inner edge
and wiping to the outer edge.
Caring for your CD-ROM Drive
Your CD-ROM drive is durable but you
must treat it with care. Please pay attention to the
following points:
■
■
■
■
■
■
The drive rotates the compact disk at a very high
speed. Do not carry it around or subject it to shock
or vibration with the power on.
Avoid using or storing the drive where it will be
exposed to extreme temperatures.
Avoid using or storing the drive where it is
damp or dusty.
Avoid using or storing the drive near magnets or
devices that generate strong magnetic fields.
Avoid using or storing the drive where it will be
subjected to shock or vibration.
Do not disassemble or dismantle the CD-ROM drive.
PC CARDS
Caring for your PC Cards
PC Cards are durable, but you must treat them with
care. The documentation supplied with your PC Card
69
"
LifeBook B Series – Section Six
70
"
7
Specifications
71
"
LifeBook B Series – Section Seven
72
"
Specifications
Specifications
CONFIGURATION LABEL
Your LifeBook contains a configuration label located on
the bottom of your LifeBook. (See figure 2-8 on page 12
for location) This label contains specific information
regarding the options you’ve chosen for your LifeBook.
Following is an example label and information on how
to read your own configuration label.
This section provides the hardware and environmental
specifications for your Fujitsu LifeBook B Series.
Specifications of particular configurations will vary.
Part Number
Configuration ID
Operating System
01013AQ
CPXXXXXXXXXXXX
B-2175, Celeron 500, 10.4T, 64M, 98, 10G
Model
Processor
Memory
Screen Size
Hard Drive
Figure 7-1 Configuration Label
MICROPROCESSOR
AUDIO
Intel Celeron 500 MHz low-voltage processor.
■
MEMORY
■
System Memory
64MB or 128MB SDRAM pre-installed,
with 256MB SDRAM maximum
Cache Memory
128K On-die L2
BIOS Memory
512KB Flash ROM
256 Bytes CMOS RAM with back-up battery
VIDEO
Built-in color flat-panel TFT active matrix LCD display
with simultaneous display capability.
Video Color and Resolution
10.4" SVGA TFT
■
Internal: 800 x 600 pixel resolution, 256K colors.
■ External: 1280 x 1024 pixel resolution, 256 colors.
Simultaneous Video = Yes (800 x 600, 16 bit high
color max) XGA, SVGA and VGA compatible.
Video RAM
4MB Embedded SDRAM.
■
■
■
SoundBlaster Pro-compatible 32-bit stereo PCM/FM
sound chip.
Stereo headphone jack, 1 Vrms, or less, minimum
impedance 32 Ohms.
Mono microphone jack, 125 mVp-p or less, minimum
impedance 10K Ohms.
Two built-in speakers, 28 mm diameter (Stereo).
One built-in monaural microphone.
MASS STORAGE DEVICE OPTIONS
Floppy Disk Drive
External USB 3.5" Floppy Disk Drive, which accommodates 1.44MB or 720KB floppy disks.
INTEGRATED POINTING DEVICE
Quick Point pointing device.
LIFEBOOK SECURITY/APPLICATION PANEL
Application Launcher buttons default to the following:
Label
Button Function
Default Application
1
Application A
Microsoft Works
2
Application B
Calculator
3
Internet
Internet Explorer
4
E-Mail
Netscape Messenger
73
"
LifeBook B Series – Section Seven
THEFT PREVENTION LOCK
KEYBOARD
Lock slot for use with physical restraining security
systems. The locking system by Kensington is
recommended.
Built-in keyboard with all functions of 101 key PS/2
compatible keyboards.
■ Total number of keys: 83.
■
Function keys: F1 through F12.
■
Feature extension key: Fn.
■ Three Windows keys: two Start keys and one
application key
■
Key pitch: 17 mm.
■ Key stroke: 2 mm.
■
Built-in Quick Point pointing device with
left and right buttons.
■ Built-in Palm Rest.
COMMUNICATIONS
Modem: Internal Multinational V.90 standard 56K fax/
modem (ITU V.90, 56K data, 14.4K fax.), and
LAN: 10/100 base-Tx Ethernet.
* Actual data transfer rate over U.S. telephone lines
varies and is less than 56Kbps due to the current FCC
regulations and line conditions.
DEVICE PORTS
On the LifeBook:
■
PC Card slot for two Type II or one Type III cards:
PCMCIA Standard 2.1 with CardBus support
■
One 15-pin D-SUB connector for VGA external
monitor (see Display specifications)
■
Two USB (Universal Serial Bus) connectors for
input/output devices.
■
One modular modem (RJ-11) connector.
■
One LAN (RJ-45) connector.
■ One stereo headphone jack. (See Audio specifications)
■
One mono microphone jack.
(See Audio specifications)
■
One IrDA port for infrared devices.
■
One 100-pin connector for docking devices.
■ One embedded SmartCard Reader (requires an
optional SmartCard adapter and a third-party application)
On the Port Replicator:
■ One 6-pin mini DIN PS/2 compatible connector,
for external keyboard, external mouse or external
numeric keypad.
■
One 15-pin D-SUB connector for VGA external
monitor (see Display specifications).
■
One 25-pin D-SUB connector for parallel input/
output devices; Bi-directional, output only or ECP.
■
One 9-pin D-SUB connector for RS-232C serial
input/output devices.
■
One 25-pin special connector for external floppy
disk drive connection.
■
One RJ-45 port for LAN connectivity
External Keyboard Support
PS/2-compatible.
External Numeric Keypad Support
PS/2-compatible.
External Mouse Support
PS/2-compatible.
POWER
Batteries
One 3-cell Lithium ion battery, rechargeable, 10.8V,
1800mAh. (Two batteries are shipped with the system:
One installed, and one spare.) An optional 6-cell, 10.8V,
3600mAh battery is also available.
Bridge Battery
Your LifeBook comes equipped with a bridge battery. A
bridge battery allows a charged Lithium ion battery to be
replaced without shutting down the system. The bridge
battery capacity is not large and can vary with the condition or your LifeBook, so you will have three minutes at
the most to make the change.
AC Adapter
Autosensing 100-240V AC, 40W, supplying 16V DC to
the LifeBook, Fujitsu Model FPCAC16 which includes
an AC cable.
Power Management
Conforms to ACPI (Advanced Configuration and Power
Interface) standards.
DIMENSIONS AND WEIGHT
Overall Dimensions
Approximately 9.92"(w) x 8.54"(d) x 1.26"(h).
Weights
Approximately 2.95 lbs with 3-cell battery.
Approximately 3.61 lbs with Port Replicator and 3-cell
battery.
74
" Specifications
ENVIRONMENTAL REQUIREMENTS
Temperature
Operating: 5° to 35° C (41° to 95° F).
Non-operating: –15° to 60° C (5° to 140° F).
Humidity
Operating: 20% to 85%, relative, non-condensing.
Non-operating; 8% to 85%, relative, non-condensing.
Altitude
Operating: 10,000 feet (3,048 m) maximum.
POPULAR ACCESSORIES
For ordering or additional information on Fujitsu
accessories please visit our Web site at
www.fujitsupc.com or call 1-800-733-0884.
Memory Upgrades
■
128MB SDRAM
■ 256MB SDRAM
Docking/Expansions
■
Additional Port Replicator
■ Universal LAN Hub
Power
■
3-cell Lithium ion battery pack
■ 6-cell Lithium ion battery pack
■
Battery Charger
■
Auto/Airline Adapter
■ AC Adapter
Storage
■
External CD-ROM drive
PC Cards
■
Xircom® CreditCard™ Modem 56K GlobalACCESS™
Additional Accessories
■ Wireless Keyboard and Mouse
■
Numeric Keypad
■
USB Camera
■ Presentation Audio system
■
TeleAdapt 16' TeleCord
■
IBM Modem Saver
■ Notebook Guardian Lock
■
Stylus Five Pack
■
Pointing Cap
Carrying Cases
■
Duo Carrying Case
■
Diplomat Carrying Case
PRE-INSTALLED SOFTWARE
Your LifeBook comes with pre-installed software for
playing audio and video files of various formats. The
software configuration installed is dependent upon the
operating system that is pre-installed on your system. In
addition, there is file transfer software, virus protection
software and Power Management software.
LEARNING ABOUT YOUR
APPLICATION SOFTWARE
Tutorials
All operating systems and most application software
have tutorials built-into them upon installation. We
highly recommend that you step through the tutorial
before you use an application.
Manuals
Included with your LifeBook you will find manuals for
your operating system and other pre-installed software.
Manuals that are not included are available online
through the help system of the software. We recommend
that you review these manuals for general information
on the use of these applications.
Microsoft Windows 98 Second Edition
or 2000 Professional
Depending upon the configuration of your LifeBook,
either Microsoft Windows 98 Second Edition or
Microsoft Windows 2000 Professional is installed as
your operating system.
PC Doctor 2000
PC Doctor® by PC-Doctor.com, Inc. is primarily for use
by your support representative when assisting you
with troubleshooting.
LapLink 2000
(with Windows 98 Second Edition Only)
LapLink® Professional by LapLink.com, Inc., allows you
to transfer files directly to other computers via an
internal modem, a PC Card modem, the infrared port,
the USB port, or a serial or parallel cable (cables not
included). (See your LapLink online help for proper operating procedures)
Microsoft Works
Microsoft Works is a suite of software containing the
basic tools to write letters and reports, track family and
friends address books, manage home finances, and
create a home inventory.
McAfee.com, Inc. ActiveShield
ActiveShield, by McAfee, is an antivirus program that
can be run after loading data or programs onto your
notebook. It assists in protecting the data currently
residing on your hard disk from contamination and
destruction. (See your ActiveShield online help or manual
for more information on how and when to run this
program)
75
"!
LifeBook B Series – Section Seven
McAfee.com Clinic on-line coupon
Clinic, by McAfee.com, is a web-based antivirus
program that can be run from the McAfee.com website
after loading data or programs onto your LifeBook. It
assists in the protection of the data currently residing on
your hard disk from destruction or contamination. (Go
to http://www.mcafee.com for more information on how
and when to run this program.)
Drive Image Special Edition (DISE) by PowerQuest
DISE by PowerQuest provides a way to restore your
computer if you experience a hard disk crash or other
system failure. DISE is used to restore the factory image
and restore the system to its original state.
BatteryAid by Fujitsu Limited
BatteryAid allows you to control the display brightness
of your LifeBook in order to maximize battery life. (See
your BatteryAid online help for more information on the
correct way to use this program)
POINT
As your notebook does not support the CPU Clock
control, the option is not active within the Power Control
menu of BatteryAid.
Microsoft Internet Explorer
Internet Explorer is installed as your default internet
browser.
Netscape Communicator by Netscape
Communications Corporation
Netscape Explorer is installed as an alternative browser.
Adobe Acrobat Reader
The Adobe Acrobat Reader, located in the Service and
Support Software folder, allows you to view, navigate,
and print PDF files from across all of the major
computing platforms.
LifeBook Security/Application Panel Software
Your LifeBook is pre-installed with software utilities that
let you operate and configure your LifeBook Application
Panel. These utilities are found under the Start menu,
under Programs, then under LifeBook Application
panel. They include a CD Player, Application Panel
Setup, Application Panel Guide, Activate Panel and
Deactivate Panel.
76
""
8
Glossary
77
"#
LifeBook B Series – Section Eight
78
"
Glossary
Glossary
AC Adapter
A device which converts the AC voltage from a
wall outlet to the DC voltage needed to power
your LifeBook.
ACPI
Advanced Configuration and Power Interface
Active-Matrix Display
A type of technology for making flat-panel displays
which has a transistor or similar device for every pixel
on the screen.
APM
Advanced Power Management.
Auto/Airline Adapter
A device which converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to
the DC voltage needed to power your LifeBook.
BIOS
Basic Input-Output System. A program and set of
default parameters stored in ROM which tests and
operates your LifeBook when you turn it on until it
loads your installed operating system from disk. Information from the BIOS is transferred to the installed
operating system to provide it with information on
the configuration and status of the hardware.
Bit
An abbreviation for binary digit. A single piece of
information which is either a one (1) or a zero (0).
CardBus
A faster, 32-bit version of the PC Card interface
which offers performance similar to the 32-bit
PCI architecture.
CD-ROM
Compact disk read only memory. This is a form of
digital data storage which is read optically with a laser
rather than a magnetic head. A typical CD-ROM can
contain about 600MB of data and is not suject to heads
crashing into the surface and destroying the data when
there is a failure nor to wear from reading.
CMOS RAM
Complementary metal oxide semiconductor random
access memory. This is a technology for manufacturing
random access memory which requires very low levels of
power to operate.
COMM Port
Abbreviation for communication port. This is your
serial interface connection.
Command
An instruction which you give your operating
system. Example: run a particular application or
format a floppy disk.
Configuration
The combination of hardware and software that makes
up your system and how it is allocated for use.
CRT
Cathode Ray Tube. A display device which uses a beam
of electronic particles striking a luminescent screen. It
produces a visual image by varying the position and
intensity of the beam.
bps
An abbreviation for bits per second. Used to describe
data transfer rates.
Data
The information a system stores and processes.
Boot
To start-up a computer and load its operating system
from disk, ROM or other storage media into RAM.
DC
Direct current. A voltage or current that does not
fluctuate periodically with time.
Bus
An electrical circuit which passes data between the CPU
and the sub-assemblies inside your LifeBook.
Default Value
A pre programmed value to be used if you fail to
set your own.
Byte
8 bits of parallel binary information.
DIMM
Dual-in-line memory module.
Cache Memory
A block of memory built into the micro-processor
which is much faster to access than your system RAM
and used in specially structured ways to make your
overall data handling time faster.
Disk
A spinning platter of magnetic data storage media. If the
platter is very stiff it is a hard drive, if it is highly flexible
it is a floppy disk, if it is a floppy disk in a hard housing
with a shutter it is commonly called a diskette.
79
#
LifeBook B Series – Section Eight
Disk Drive
The hardware which spins the disk and has the heads
and control circuitry for reading and writing the data
on the disk.
Diskette
A floppy disk in a hard housing with a shutter.
DMA
Direct Memory Access. Special circuitry for memory
to memory transfers of data which do not require
CPU action.
DMI
Desktop Management Interface. A standard that
provides PC management applications with a common
method of locally or remotely querying and configuring
PC computer systems, hardware and software components, and peripherals.
Floppy Disk
A spinning platter of magnetic data storage media which
is highly flexible.
GB
Gigabyte.
Hard drive
A spinning platter of magnetic data storage media where
the platter is very stiff.
Hexadecimal
A decimal notation for the value of a 4 bit binary
number. (0-9, A, B, C, D, E, F) Example: 2F in hexadecimal = 00101111 in binary = 47 in decimal.
I/O
Input/Output. Data entering and leaving your LifeBook
in electronic form.
DOS
Disk Operating System (MS-DOS is a Microsoft Disk
Operating System).
I/O Port
The connector and associated control circuits for data
entering and leaving your LifeBook in electronic form.
Driver
A computer program which converts application and
operating system commands to external devices into the
exact form required by a specific brand and model of
device in order to produce the desired results from that
particular equipment.
IDE
Intelligent Drive Electronics. A type of control interface
for a hard drive which is inside the hard drive unit.
ECP
Extended Capability Port. A set of standards for high
speed data communication and interconnection
between electronic devices.
ESD
Electro-Static Discharge. The sudden discharge of electricity from a static charge which has built-up slowly.
Example: the shock you get from a doorknob on a dry
day or the sparks you get from brushing hair on a dry
day.
Extended Memory
All memory more than the 640KB recognized by
MS-DOS as system memory.
FCC
Federal Communication Commission.
80
Infrared
Light just beyond the red portion of the visible light
spectrum which is invisible to humans.
IR
An abbreviation for infrared.
IrDA
Infrared Data Association. An organization which
produces standards for communication using infrared
as the carrier.
IRQ
Interrupt Request. An acronym for the hardware signal
to the CPU that an external event has occurred which
needs to be processed.
KB
Kilobyte.
#
Glossary
LAN
Local Area Network. An interconnection of computers
and peripherals within a single limited geographic
location which can pass programs and data amongst
themselves.
LCD
Liquid Crystal Display. A type of display which makes
images by controlling the orientation of crystals in a
crystalline liquid.
Lithium ion Battery
A type of rechargeable battery which has a high powertime life for its size and is not subject to the memory
effect as Nickel Cadmium batteries.
LPT Port
Line Printer Port. A way of referring to parallel
interface ports because historically line printers were
the first and latter the most common device connected
to parallel ports.
MB
Megabyte.
Megahertz
1,000,000 cycles per second.
Memory
A repository for data and applications which is readily
accessible to your LifeBook CPU.
MHz
Megahertz.
MIDI
Musical Instrument Digital Interface. A standard
communication protocol for exchange of information
between computers and sound producers such
as synthesizers.
Modem
A contraction for MOdulator-DEModulator. The
equipment which connects a computer or other data
terminal to a communication line.
Monaural
A system using one channel to process sound
from all sources.
MPU-401
A standard for MIDI interfaces and connectors.
NTSC
National TV Standards Commission. The standard for
TV broadcast and reception for the USA.
Operating System
A group of control programs that convert application
commands, including driver programs, into the exact
form required by a specific brand and model of microprocessor in order to produce the desired results from
that particular equipment.
Parallel Port
A connection to another device through which data is
transferred as a block of bits simultaneously with a wire
for each bit in the block and with other wires only for
control of the device not for transfer of data.
Partition
A block of space on a hard drive which is set aside
and made to appear to the operating system as if it
were a separate disk, and addressed by the operating
system accordingly.
PCMCIA
PCMCIA is a trademark of the Personal Computer
Memory Card International Association. The Personal
Computer Memory Card International Association is an
organization that sets standards for add-in cards for
personal computers.
Peripheral Device
A piece of equipment which performs a specific
function associated with but not integral to a computer.
Examples: a printer, a modem, a CD-ROM.
Pitch (keyboard)
The distance between the centers of the letter keys
of a keyboard.
Pixel
The smallest element of a display, a dot of color on your
display screen. The more pixels per area the clearer your
image will appear.
POST
Power On Self Test. A program which is part of the BIOS
which checks the configuration and operating condition
of your hardware whenever power is applied to your
LifeBook. Status and error messages may be displayed
before the operating system is loaded. If the self test
detects failures that are so serious that operation can not
continue, the operating system will not be loaded.
81
#
LifeBook B Series – Section Eight
Program
An integrated set of coded commands to your
computers telling your hardware what to do and how
and when to do it.
PS/2
An IBM series of personal computers which established
a number of standards for connecting external devices
such as keyboards and monitors.
RAM
Random Access Memory. A hardware component of
your LifeBook that holds binary information (both
program and data) as long as it has the proper power
applied to it.
RAM Module
A printed circuit card with memory and associated
circuitry which allows the user to add additional
memory to the computer without special tools.
Reset
The act of reloading the operating system. A reset erases
all information stored in RAM.
Shadow RAM
A technique of copying data or applications stored in
ROM (Read Only Memory) into RAM (Random Access
Memory) for access during actual operation. RAM is
much faster to access than ROM, however ROM
contents are not lost when power is removed.
Shadowing allows permanently stored information
to be rapidly accessed.
SMART
Self-Monitoring, Analysis and Reporting Technology
(SMART) is an emerging technology that provides nearterm failure predictions for hard drives. When SMART is
enabled the hard drive monitors pre-determined drive
attributes that are susceptible to degradation over time.
If a failure is likely to occur, SMART makes a status
report available so that the LifeBook can prompt the
user to back up the data on the drive. Naturally not all
failures are predictable. SMART predictability is limited
to those attributes which the drive can self-monitor. In
those cases where SMART can give advance warning, a
considerable amount of precious data can be saved.
Restart
See Reset.
SRAM
Static random access memory. A specific technology
of making RAM which does not require periodic
data refreshing.
Resume
To proceed after interruption. In your LifeBook this
refers to returning to active operation after having been
in one of the suspension states.
Status Indicator
A display which reports the condition of some portion
of your hardware. On your LifeBook this is an LCD
screen just above the keyboard.
ROM
Read Only Memory. A form of memory in which information is stored by physically altering the material. Data
stored in this way can not be changed by your LifeBook
and does not require power to maintain it.
Stereo (audio)
A system using two channels to process sound from two
different sources.
SDRAM
Synchronous Dynamic Random Access Memory.
Serial Port
A connection to another device through which data is
transferred one bit at a time on a single wire with any
other wires only for control of the device not for transfer
of data.
82
Stroke (keyboard)
The amount of travel of a key when it is pressed from
resting to fully depressed.
Suspend
To make inoperative for a period of time. Your LifeBook
uses various suspension states to reduce power
consumption and prolong the charge of your battery.
#
Glossary
SVGA
Super VGA.
S-Video
Super Video. A component video system for driving a
TV or computer monitor.
System Clock
An oscillator of fixed precise frequency which synchronizes the operation of the system and is counted to
provide time of day and date.
TFT
Thin Film Transistor – A technology for flat display
panels which uses a thin film matrix of transistors to
control each pixel of the display screen individually.
UL
Underwriters Laboratories – An independent organization that tests and certifies the electrical safety of
devices.
VRAM
Video Random Access Memory. A memory dedicated to
video display data and control.
WFM
Wired for Management is Intel’s broad-based initiative
to reduce the total cost of ownership (TCO) of business
computing without sacrificing power and flexibility.
Write Protect
Prevent alteration of the binary state of all bits in a
storage media. Example: all information on a device
such as a floppy diskette; a block of space in a storage
media such as a partition of a hard drive; a file or directory of floppy diskette or hard drive.
XGA
Extended VGA.
Zip Drive
A 100MB read/write removable media disk drive.
VGA
Video Graphics Array. A video display standard
originally introduced by IBM with the PS/2 series of
personal computers.
83
#
LifeBook B Series – Section Eight
84
# Index
Index
A
Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
AC
adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27, 79
indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
plug adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Anti-theft Lock Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DC Power Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 27
Application
See Pre-installed Software
Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Auto/Airline Adapter . . . . . . . . . . . . . . . . . . . . . . . 27, 79
DISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63, 76
B
Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9, 28
adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
power management . . . . . . . . . . . . . . . . . . . . . . . . . 28
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58, 59
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
charging indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 14
cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
conserving power . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
dead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
faulty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
increasing life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
level indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
lithium ion battery . . . . . . . . . . . . . . . . . . . . . . . 37, 81
low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56, 57
recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
shorted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
suspend mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
warm-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
D
DC Output Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Display Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Drive Image Special Edition . . . . . . . . . . . . . . . . . . . . 63
Drivers and Application CD . . . . . . . . . . . . . . . . . . . . 63
E
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Extended Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
External Monitor Port . . . . . . . . . . . . . . . . . . . . . . 11, 47
F
BatteryAid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Flexible Bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
setup utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Floppy Disk
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
ejecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
formatting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
preparing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
write protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Built-in Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Built-in Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
C
Cache Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
CapsLock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CD-ROM
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Closed Cover Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cold-swapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
COMM Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Floppy Disk Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44, 47
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Function Key
F10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
F5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
F6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
F7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 20
FN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Fn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
85
#!
LifeBook B Series
H
Modem Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Hard Disk Drive
access indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Modem Result Codes . . . . . . . . . . . . . . . . . . . . . . . . . .62
Hard Disk Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 47
Hibernation Feature . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Mouse
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
See Quick Point
N
Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
I
NumLk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Idle Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
P
Infrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 47
Internal LAN Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
IrDA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
K
Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8, 15
cursor keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
L
LifeBook
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
traveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
LifeBook Application Panel . . . . . . . . . . . . . . . . . . . . . 8
LifeBook Security Application Panel . . . . . . . . . . . . .
buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
configuring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
launching applications . . . . . . . . . . . . . . . . . . . . . .
operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
23
23
24
23
22
21
24
22
M
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 42
extended . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
upgrade module . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 47
Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
86
Parallel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46, 81
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
PC Card
access indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Port Replicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
attaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
detaching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
POST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Power
AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Auto/Airline adapter . . . . . . . . . . . . . . . . . . . . . . . .27
failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Power Management . . . . . . . . . . . . . . . . . . . . . . . .32, 34
Power On Self Test . . . . . . . . . . . . . . . . . . . . . . . . .29, 61
Pre-Installed Software . . . . . . . . . . . . . . . . . . . . . . . . .75
manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
tutorials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
PS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
PS/2 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Q
Quick Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
control adjustment . . . . . . . . . . . . . . . . . . . . . . . . . .18
double-clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
#"
Index
R
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30, 31
Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Restoring your hard disk . . . . . . . . . . . . . . . . . . . . . . . 63
RJ-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
S
Save-to-Disk Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
ScrLk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 42
Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46, 82
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Software
See Pre-installed Software
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Status Indicator Panel . . . . . . . . . . . . . . . . . . . . . . . 8, 13
Suspend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Suspend Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Suspend/Resume Button . . . . . . . . . . . . . . . . . . . . . . . . 8
T
Theft Prevention Lock . . . . . . . . . . . . . . . . . . . . . . . . . 74
Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
calibrating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
double-clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
U
Universal Serial Bus Port . . . . . . . . . . . . . . . . . . . . . . . 47
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47, 54
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
W
Warm-swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
end user license agreement . . . . . . . . . . . . . . . . . . . 30
Windows keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Application key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Start keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
87
##
LifeBook B Series
88