Download American Standard Chandler 7048 Series User's Manual
Transcript
™ M A D E W I T H Installation Instructions CHANDLER™ APRON KITCHEN SINK MODEL 7048 SERIES Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. Certified to comply with ANSI Z124.6 Patent Pending Observe local plumbing and building codes. 790759-100 REV A BEFORE YOU BEGIN...Unpack new sink and inspect carefully for damage. Replace the sink in its original packing carton to protect it until you are ready to begin installation. RECOMMENDED TOOLS & MATERIALS Putty Knife Phillips Screwdriver Pipe Wrench Regular Screwdriver Channel Locks Adjustable Wrench Drill Basin Wrench Saber Saw Plumbers' Putty or Caulking Various Carpentry Tools Tubing Cutter Tape Measure Hacksaw Silicone Adhesive PRODUCT REQUIREMENTS Due to the special nature of this installation, American Standard recommends that an experienced cabinet maker build the new cabinet or modify an existing cabinet to achieve a satisfactory installation. To ensure proper fit of the sink in the cabinet, we suggest you provide the cabinet maker with the actual sink that will be installed. NOTES The cabinet designs illustrated below are intended as suggestions only. Your specific installation requirements may vary from those shown. CABINET DESIGN The sink is designed to be installed with the apron exposed and the back of the apron flush against the front of the cabinet. SINK DIMENSIONS 1-3/4 (44mm) DIA. 1-3/8 (35mm) DIA. HOLES TYP. NOTE: Tile recess is designed to accept four 6" x 6" x 5/16" thick tiles (by others). Secure tiles with silicone adhesive. C/L 7-1/8 8-3/4 (181mm) (222mm) 7048.804 4 HOLE VARIATION 22 (558mm) 3-1/2 (89mm) DIA. 1 (25mm) RAD. TYP. 9-1/2 (241mm) 4-1/2 (114mm) 36 (914mm) 1-1/2 (38mm) REF. SEALING COMPOUND 3/8 (10mm) 6-3/16 (157mm) 9-3/4 (248mm) 24-1/2 (622mm) TILE RECESS 33 (838mm) Product names listed herein are trademarks of American Standard Inc. unless otherwise noted. Corian® Dupont registered trademark 2 (51mm) FRONT OF CABINET © American Standard Inc. 2004 1 SINK INSTALLATION SINK UPSIDE DOWN C CENTER MARK ON BACKSIDE OF SINK B ALIGN MARKS A CENTER OF MOUNTING LOCATION MARKED ON COUNTERTOP C Mark SIDE VIEW X SINK PLACED UPSIDE DOWN ON COUNTERTOP COUNTERTOP TOP VIEW COUNTERTOP C/L A E TRACE THIS EDGE 22 (559mm) X SHOULD BE MAXIMUM 25mm (1") D CABINET FACE CABINET FACE APRON EDGE X APRON PORTION OF SINK B A. Mark center of backside of sink. Mark center of location on counter top approx. 22in. from outside edge of countertop. B. Mark countertop to show the cabinet face location (dim. X) . C. Place sink, upside down, on countertop. Align centerline marks of sink and countertop. D. Align the apron edges with the cabinet face marks on countertop. E. Trace outside of sink (this is not the cut line.). Carefully remove sink, set aside. 1a SINK CUTOUT B TRACED LINE OF SINK SINK CUTOUT LINE COUNTERTOP DIM "X" B SINK CUTOUT LINE 3/8 IN. MAX. 25mm (1") COUNTERTOP OVERHANG-DIM "X" CABINET FACE A. Measure 3/8 in. inside of marked line - this is the sink cutout line. B. Cut out countertop. 790759-100 REV A 2 A 1b COUNTERTOP NOTCH AND CABINET CUTOUT MARKED LINE OF SINK SINK CUTOUT LINE 10mm (3/8") X TRACED LINE OF SINK SINK CUTOUT LINE A CUT LINES FOR NOTCH 9-1/4 (235mm) MARKED LINE OF SINK 32-1/4 (819mm) B CABINET FACE CUTOUT MAX. 25mm (1") COUNTERTOP OVERHANG-DIM "X" CABINET FACE A. The cut allows the apron portion of the sink to fit in the countertop. B. Cut the cabinet face per the diagram. C. Drop in sink and check fit. Be sure apron edges touch the cabinet face. 1C INSTALLED VIEW (after completing steps 2 thru 7) 790759-100 REV A FRONT EDGE OF COUNTERTOP TOP VIEW FOLLOW THE SINK CUTOUT LINE VERTICALLY DOWN ON THE CABINET 3 CABINET FACE 2 3 4 5 Mount the faucet and drain assembly on the sink following the manufacturer's instructions. Before applying the sealant, place the sink temporarily into the cutout. Check for alignment and clearance, then trace around the outside edge of the sink as a guide for installation location and application of sealant. Remove sink. Apply a masking tape outline 1/8" outside traced outline as a guide for application of silicone sealant. Cutout Masking Tape 6 Sink outline Silicone Sealant Sink Connect supply lines to faucet finger tight, and carefully bend to engage with the supply stops. Tighten connections to faucet for secure seal. 1/8" 7 Masking tape outline AMERICAN STANDARD TEN-YEAR LIMITED WARRANTY CORIAN® SINK If inspection of the Corian Sink of this American Standard product, within ten years after its initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model. This warranty applies only to the original purchaser and installation of these products. All labor and transportation costs or charges incidental to warranty service are to be borne by the original consumer-purchaser. Double Bowl Corian® Care & Maintenance Tips American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.) Cleaning This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state of from province to province, in which case this warranty does not affect such statutory rights. For residents of the United States, warranty information may also be obtained by calling the following toll free number: (800) 442-1902 In Canada: American-Standard, 1401 Dupont Street, Toronto, Ontario Canada M6H 2B1 Toll free: (800) 387-0369 Most dirt and stains Use soapy water or ammonia-based cleaner. Water marks Wipe with damp cloth; towel dry. Difficult stains Use an abrasive cleanser and a green Scotch-Brite* pad. Disinfecting Occasionally wipe surface with diluted household bleach (1 part water/1 part bleach). Maintenance Rub with Scotch-Brite* pad alone. *Registered trademark of the 3M Company 790759-100 REV A B A Trap This warranty shall be void if the product has been fabricated or modified in a manner inconsistent with the product as shipped by American-Standard; moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damages; or if it was not installed in accordance with American Standard's instructions. In the United States: American Standard Inc., P. O. Box 6820 Piscataway, NJ 08855 Attention: Director of Consumer Affairs Connect drain assembly hand tight to check alignment. It may be necessary to cut off part of the tailpiece (area "A") or part of the horizontal leg of the trap (area "B"). Secure joint for watertight assembly. This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation. In Mexico: Customer Service Manager Ideal Standard, S.A. de C.V. Via Morelos #330 Col. Santa Clara Ecatepec 55540 Edo. Mexico Apply a generous portion of silicone sealant inside line traced on countertop. Carefully lower sink into place and press down firmly. Use guidelines for proper positioning. Using water to dampen your finger, remove excess sealant for a smooth even line. Apply additional sealant if necessary to provide a uniform bead from the rim of sink to the masking tape line as shown. Carefully remove tape. Dampen finger and run it slightly over the sealant to remove any high spots. 4