Download Ergotron 200 Series adjustable wall mount system, black

Dimensional Illustrations
Ergotron 200 Series
®
fixed height pivots and extensions
Rotation…
• Telescopic motion
360˚
360˚
180˚
20"
(508 mm)
Top View
Monitor Pivot…
180˚
360˚
180˚
Side View
Up/down tilt
Front View
Portrait/landscape
Top View
Left/right tilt
Bow Pivot…
• Up/down tilt controlled by adjustment lever: +25°/-10°
• Portrait/landscape motion available with single-arm configurations only
360
35
Side View
Up/down tilt
Front View
Clock-rotation
Keyboard/Laptop and Combo Pivots…
105˚
180˚
90˚
© 2006 Ergotron, Inc.
rev. 02/28/2006 DIM-035
Content is subject to change
without notification.
Ergotron, Inc.: St. Paul, MN; (800) 888-8458;
www.ergotron.com; [email protected]
Ergotron Europe: Amsterdam, The Netherlands;
Tel. +31 20 312.29.39; [email protected]
Ergotron Asia: (800) 468-3917 ext. 7617;
[email protected]
200 SERIES
Desk Mount (Desk Clamp and Grommet Mount) Base
Vertical Mount Base
1.787"
(45.4 mm)
ø .2"
Ø.340"
A
1.13"
(28.7 mm)
(8.6 mm)
.662" (16.8 mm)
1.787"
1.944"
(45.4 mm)
(49.4 mm)
B
4.881"
(5.1 mm)
A
A
(124 mm)
4.1"
(104 mm)
Ø.188"
2.102"
Ø.348"
(53.4 mm)
(4.8 mm)
(8.8 mm)
2.7"
3.889"
(68.6 mm)
(98.8 mm)
4.8"
(122 mm)
A
A: #10-24 UNC Tap
.35 Deep,
Break through
allowed
B #3/8-16 UNC Tap
1.0 Deep,
No break through
allowed
WALL MOUNT PLATE
Wall Mount Plate Hole Pattern
3.5"
ø .281"
TABLE A: Weight Capacity When Adding Extensions
(88.9 mm)
(7.1 mm)
(6 through holes)
When adding Extensions to a 200 Series system, use the formula below to
calculate the maximum allowable load:
#10-24
(10 tap holes)
Holes used
to attach
Vertical Mount
#8-32
(4 tap holes)
8.375"
(213 mm)
Outline of
an attached
Vertical Mount
3.75"
(95.3 mm)
(12.7 mm)
Load (L) = The weight in pounds of the monitor.
Example:
Therefore:
1.25"
(31.8 mm)
(12.7 mm)
C/G
Distance (D) = The measurement in inches on a horizontal
plane from the center-line of the mounting bracket to the
center-of-gravity (C/G) of the monitor.
Monitor weighing 25 lbs using three 9" Extensions
and a Single Pivot with P/L.
.5"
.5"
D x L = maximum inch-lbs (not to exceed 900)
1.125"
(28.6 mm)
2.5"
(63.5 mm)
D = (3 x 9") + 5" = 32"
L = 25 lbs
32" x 25 lbs = 800 inch-lbs
9"
9"
9"
27"
32" (D)
As 800 is less than 900, your component can be used in this configuration.
© 2006 Ergotron, Inc.
rev. 02/28/2006 DIM-035
Content is subject to change
without notification.
Ergotron, Inc.: St. Paul, MN; (800) 888-8458;
www.ergotron.com; [email protected]
Ergotron Europe: Amsterdam, The Netherlands;
Tel. +31 20 312.29.39; [email protected]
Ergotron Asia: (800) 468-3917 ext. 7617;
[email protected]
5"
200 SERIES
25"
3-1/4"
(635 mm)
Vertical Mount Monitor Arms
9"
9"
(229 mm)
(229 mm)
(83 mm)
Extensions
9"
1-7/8"
6-1/8"
(229 mm)
(48 mm)
3-3/8"
11-1/2"
(156 mm)
28-106-xxx
(86 mm)
(292 mm)
28-096-xxx
5-1/2"
45-056-xxx
(140 mm)
2-3/4"
(70 mm)
5"
21-3/4"
3-1/2"
6-3/4"
(552 mm)
(89 mm)
(171 mm)
9"
9"
(229 mm)
(229 mm)
(127 mm)
(86 mm)
6"
(152 mm)
NO
LONGER
AVAILABLE
1"
(25 mm)
3-3/8"
45-121-xxx
NO
17" (max.)
21"
LONGER
(432 mm)
(533 mm)
AVAILABLE
NO
LONGER
AVAILABLE
7-1/4"
(184 mm)
3-1/4"
NO
LONGER
AVAILABLE3-3/8"
(83 mm)
28-153-xxx
(86 mm)
28-144-xxx
Vertical Mount Combo Arm
45-120-xxx
Desk Mount Monitor Arm
10-7/8"
Mounts
(276 mm)
33-069-xxx
23-1/2"
28-188-xxx
1-7/8"
(48 mm)
(597 mm)
9"
(229 mm)
9"
16-7/8"
to 15"
(229 mm)
9"
9"
(229 mm)
(229 mm)
3-1/4"
(83 mm)
6"
5-1/8"
(152 mm)
(130 mm)
(429 to 381 mm)
2"
2-1/8"
(51 mm)
(54 mm)
1-3/8"
(35 mm)
28-097-xxx
19-7/8"
19-5/8"
(505 mm)
(498 mm)
Crossbar
14-1/2"
4-1/2"
(368 mm)
(114 mm)
6"
(152 mm)
(76 mm)
Miscellaneous Slatwall Config.
1-7/8"
(48 mm)
21"
28"
(533 mm)
(711 mm)
7-1/4"
60-249-xxx
5"
(127 mm)
5-1/2"
(184 mm)
12-1/4"
(140 mm)
6-7/8"
(311 mm)
(175 mm)
26"
(660 mm)
3"
60-409-xxx
Available Monitor Widths Using Crossbars
Attention:
Listed allowable widths assume monitor thickness is 4" (102 mm). If monitor
thickness is less, allowable width may
be more. Contact Ergotron for details.
200 Series Pre-configurations that use
Crossbars come standard with Sliding
Pivots (i.e., without P/L).
Number of Monitors
Sliding Pivots
Single Pivots w/ P/L
(Horizontal Crossbar)
Allowable Monitor Width*
Allowable Monitor Width*
Dual-Monitor (28" Crossbar)
23-1/4" (590 mm)
23" (584 mm)
Triple-Monitor (46" Crossbar)
20" (508 mm)
19-1/2" (495 mm)
Triple-Monitor (55" Crossbar)
24-1/2" (622 mm)
24" (609 mm)
Quad-Monitor (55" Crossbar)
16" (406 mm)
15-1/2" (393 mm)
* Width refers to monitor’s physical outside dimension – not screen size.
© 2006 Ergotron, Inc.
rev. 02/28/2006 DIM-035
Content is subject to change
without notification.
Ergotron, Inc.: St. Paul, MN; (800) 888-8458;
www.ergotron.com; [email protected]
Ergotron Europe: Amsterdam, The Netherlands;
Tel. +31 20 312.29.39; [email protected]
Ergotron Asia: (800) 468-3917 ext. 7617;
[email protected]