Download Samsung SCD-6080 surveillance camera
Transcript
HD-SDI CAMERA User Manual SCD-6080 HD-SDI Camera User Manual Copyright ©2011 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin. Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice. Warranty If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the problem for free of charge. The warranty period is 3 years. However, the followings are excluded: • If the system behaves abnormally because you run a program irrelevant to the system operation. • Deteriorated performance or natural worn-out in process of time YY Design and specifications are subject to change without prior notice. YY The default password can be exposed to a hacking thread so it is recommended to change the password after installing the product. Note that the security and other related issues caused by the unchanged password shall be responsible for the user. overview Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. ● overview 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11.Only use attachments/ accessories specified by the manufacturer. 12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13.Unplug this apparatus during lighting storms or when unused for long periods of time. 14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. English _3 overview WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT. Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. CAUTION CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. 4_ overview Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed. CAUTION These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Please use the input power with just one camera and other devices must not be connected. English _5 ● overview Battery overview Please read the following recommend safety precautions carefully. yy Do not place this apparatus on an uneven surface. yy Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. yy Do not place this apparatus near conductive material. yy Do not attempt to service this apparatus yourself. yy Do not place a glass of water on the product. yy Do not install near any magnetic sources. yy Do not block any ventilation openings. yy Do not place heavy items on the product. yy Do not expose the camera to radioactivity. User’s Manual is a guidance book for how to use the products. The meaning of the symbols are shown below. yy Reference : In case of providing information for helping of product’s usages yy Notice : If there’s any possibility to occur any damages for the goods and human caused by not following the instruction Please read this manual for the safety before using of goods and keep it in the safe place. 6_ overview CONTENTS overview installation & connection 12 Operating Your Camera 18 appendix 32 Important Safety Instructions Product Features What’s Included At a Glance 12Installation 15 Connecting with other Device 18 19 Menu Configuration Menu Setup 32Specification 34 Product Overview 35Troubleshooting English _7 ● overview 3 3 8 9 10 overview Product Features •• Supports Full HD-SDI Video By adopting a diagonal 6mm (1/3”) 2M pixel CMOS, the camera produces clear picture quality. •• Excellent low-illumination image quality By adopting high-sensitive colour CMOS, the camera provides clear image quality under a severe low illumination condition of 0.017 Lux (with SENS-UP, x60). •• SSNR3 (Samsung Super Noise Reduction) Function The high-performance WN2 DSP chip effectively removes low-light gain noise and afterimage to provide clear images even in dark environments. •• Electrical Day&Night This camera has a function that automatically selects the mode that is appropriate for daytime or night-time conditions. The COLOR mode operates in daytime conditions to provide optimum colors, and B/W mode operates in night-time conditions to enhance the definition of the image. •• Motion Detection Since the camera detects motion without any additional external sensor, you can monitor activity more efficient. •• SSDR (Samsung Super Dynamic Range) For images with high contrast between bright and dark areas from difficult lighting conditions such as backlighting, this camera selectively illuminates darker areas while retaining the same light level for brighter areas to even out the overall brightness. •• Miscellaneous Functions HLC(High Light Compensation), SENS-UP, FLIP (H/V-REV), D-ZOOM and PRIVACY functions are provided. •• OSD By providing multi-lingual user-friendly OSD (On-screen Display) menu, the camera provides easy handling of the camera. 8_ overview What’s Included Check if the main unit and all the following accessories are included in the product package. Item Name Quantity Description Camera 1 User Manual 1 Iron Screw 3 Used for fixing to an iron plate Cable for the testingmonitor 1 Used to test the camera connection to a portable display device Dustproof Plate 1 Preventing dust inflow ● overview Appearance English _9 overview At a Glance Appearance Item Description a Top cover Case cover used to protect the lens and the main unit. b Camera Case Covers the lens and camera body. c Power Port Used to plug the power cable. d e I/O Port HD-SDI Video Out terminal 10_ overview 1:GND Earth-grounding port for external signal. 2:EXT_D/N External signal reception port for Day/Night mode setup. 3:MD_OUT Output port that signals when a motion is detected. 4:RS-485+ RS-485+ signal port for RS-485 communication. 5:RS-485– RS-485– signal port for RS-485 communication. BNC terminal for HD-SDI video signal output. Inside ● overview Item a b c SETUP Switch C-VIDEO Wiring Cover Description The switch is used for setting and adjusting the camera’s functions and properties. Press and hold this switch more than 2 seconds to display the main menu on the screen. _/+ Move this switch left or right to move the cursor or change the value in the menu. $/% Move this switch up or down to move the cursor in the menu. @ Press the switch to set the function in menu. To move to a submenu item in the menu, press this switch. Analogue video output terminal of C-Video. Use a monitor cable for testing the camera with a portable display. (for installation) If you drill a hole in the wiring cover for wiring, remove the cover and attach the provided dustproof plate to it, and arrange the cables through the plate. `` The dust-proof plate is to prevent outside dust from inflow to the wiring compartment. d Lock Release To separate the bracket from the main unit for the installation or to separate the camera from an installed camera, push this release and turn the main unit in the marked direction of <UNLOCK>. English _11 installation & connection Installation Precautions before installation Ensure you read out the following instructions before installing the camera: •• Select an installation site (ceiling or wall) that can endure at least 5 times of the camera weight. •• Stuck-in or peeled-off cables can cause damage to the product or a fire. •• For safety purposes, keep anyone else away from the installation site. And put asid personal belongings from the site, just in case. Disassembling 1. Take the camera body with one hand and take the top cover with the other hand. Then, turn the cover counter clockwise to remove it. Top cover Camera Body 2. Hold down the lock lever in the outer direction as shown and turn the camera body in the <UNLOCK> direction (counter clockwise) to remove the bracket from the body. `` If it fails, take the bottom hole of the bracket and turn the bracket in the <LOCK> direction (clockwise) to remove it. Camera Body Bracket 12_ installation & connection Installation 1. Use the provided screws (x3) to fix the bracket to a desired position (ceiling or wall). `` Ensure that the <CAMERA FRONT> label on the bracket faces the direction for camera monitoring. 3. Mount the camera body onto the bracket. Align the marking hole of the camera body with the <CAMERA FRONT> label of the bracket, and turn the body in the <LOCK> direction. ● installation & connection 2. Arrange the cables through the bracket to the ceiling or wall. `` If you drill a hole in the ceiling cover for wiring, press hard to remove the cover and attach the dust-proof plate to it, and arrange the cables through the plate. If you intend to arrange the cables without drilling a hole, use the empty area opposite to the <CAMERA FRONT> label side for the wiring purpose. Wiring Cover 4. Refer to “Adjusting the monitoring direction for the camera” to adjust the lens in a desired direction. 5. Close the top cover. `` Fit the top cover into the fixing tips of the camera body and turn the cover clockwise. English _13 installation & connection Adjusting the monitoring direction for the camera Panning Tilting ❖❖ Adjusting the monitoring direction Cover Front You can adjust the camera direction only when the camera is fixed on the ceiling. Where, rotating the camera unit to the left or right is called Pan and adjusting the tilt is called Tilt. -- The effective range of pan is a total of 355 degrees. -- The effective range of tilt is a total of 90 degrees. JJ `` In some angles, the top cover may cause cutting some part of the monitoring object. `` Do not rotate the focus/zoom lens by force after removing the cover front. Otherwise, it may cause an incorrect focus due to a motor failure. ❖❖ Methods of adjustment 1. After installing the camera, adjust the panning angle in consideration of the monitoring direction. When tilting the camera, you should adjust the horizontal angle lest that the image be displayed reversely. 2. Adjust the tilt angle so that the camera faces toward the monitoring object. 14_ installation & connection Connecting with other Device ● installation & connection HD-SDI Monitor Motion detection output device Day/Night mode controller Connecting to the monitor Connect the video out port of the camera to the video input port of the monitor. initial installation of the camera, you can connect the camera to the monitor for checking MM `` Inthetheconnection status. `` When connecting a general monitor device to the HD-SDI video output, you need to use a signal converter. `` You can set the video output type to either NTSC or PAL. (page 29) Video Cable The cable connecting the camera’s video output and a monitor is a BNC coaxial cable as shown below. If the distance between the camera and the monitor exceeds the recommended maximum, please us an auxiliary video amp. Maximum video transfer distance Recommended cable specification 200m L-6CHD(75ohm) (SDI-specific Cable) 100~140m L-5C2V(75ohm) English _15 installation & connection External Day/Night Switching Input Day/Night mode of the camera can be switched by signal from an external device. MM `` To(Pageuse27)this function, <DAY/NIGHT> setting of the camera should be set to the <EXTERN>. Motion Detection Signal Out Upon a motion detection, the port outputs signal for an external device for display or operation. When a motion is detected, the port outputs 3.3V signal. MM `` To use this function, <ALARM OUT> setting of the camera should be set to <ON>. (Page 30) Power Supply Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera. JJ `` Be careful not to reverse the polarity when you connect the power cable. `` Be sure to turn the power off the device to be connected. DVR System Controller or RS-485 Converter R+ T+ T- R- CONVERTER RS232C RS485, 422 POWER PC For AC/DC Power Supply You can use either one of AC 24 V / 500 mA and DC 12V / 500 mA adaptor. 16_ installation & connection Resistance of copper wire [at 20°C (68°F)] #24(0.22mm2) #22(0.33mm2) #20(0.52mm2) Voltage Drop (V/m) 0.028 0.018 0.011 Resistance (Ω/m) 0.078 Recommended Distance (m) 0.050 Less than 20 Less than 30 0.030 Less than 30 #18(0.83mm2) 0.018 0.006 Less than 30 •• As shown in the table above, you may encounter a voltage-sag depending on the wire length. If you use an excessively long wire for camera connection, the camera may not work properly. `` Voltage for proper camera operation: DC 12V±10%, AC 24V±10% `` Voltage drop shown in the table above may show difference from the actual depending on the manufacturer and cable type. RS-485 Communications Using RS-485 communication, the camera menu can be accessed using Samsung Techwin’s System Controller or the DVR. •• For accessing the camera from a computer Use a RS-485 converter to connect the camera’s control port with the computer’s serial cable. Ex) Serial port (COM1) of computer Serial Cable RS-485 Converter Camera’s RS-485 control port •• For accessing the camera from a DVR or the System Controller connect the camera’s RS-485+ and RS-485– terminals to the RS-485 control board’s terminals of desired device with a RS-485 cable (TRX+ and TRX–). Control ports of RS-485 Controller RS-485 ports of the camera (–) CONNECTION TERMINAL (TRX–) 485– (+) CONNECTION TERMINAL (TRX+) 485+ Default RS-485 communication settings Item Default Camera Number 1 Transfer Rate 9600 Communication Mode 8-NONE-1 Return Data Not used constructing a proprietary controller for direct camera control, apply Pelco-D or Samsung-Techwin JJ `` When protocol. `` Use only a DVR model that supports HD-SDI saving. English _17 ● installation & connection Wire specification (AWG) Operating Your Camera Menu Configuration LENSa •DC MAIN SETUP •BRIGHTNESS •SHUTTER •SENS-UP •RETURN •ATW •OUTDOOR •MANUAL •AWC ➝ SET SSDR •OFF •ON BACKLIGHT •OFF •BLC SSNR3 •ON •OFF •AUTO •EXTERN •COLOR •CAM TITLE •IMAGE ADJ •MOTION DET •PRIVACY •COMM ADJ •LANGUAGE •RESET •RETURN EXPOSURE WHITE BAL DAY/NIGHT SPECIAL EXIT •AGC •INDOOR •HLC •B/W •EXIT 18_ Operating Your Camera Menu Setup To configure the camera’s function settings, use the button on the rear side of the product. ● Operating Your Camera •• $% : Moves up/down in menu. •• _+ : Moves right/left in menu. •• SET : Press the switch to set the function in camera menu. To move to a sub-menu item in the menu, press this switch. 1. Press the SET button. •• Enters the function menu. The selected function’s menu appears on the monitor. Use up/down buttons to set the desired item. MAIN SETUP ► 1. LENSDC 2. EXPOSURE 3. WHITE BAL ATW 4. SSDRON 5. BACKLIGHTOFF 6. SSNR3ON 7. DAY/NIGHTAUTO 8. SPECIAL 9. EXIT Use right/left buttons to change the selection. 2. Use the Up/Down buttons to select a desired function. •• Move the button up or down to move the arrow up or down. Set the arrow to indicate the desired item. English _19 Operating Your Camera 3. Use the Up/Down buttons to select a desired function. •• Move the button right or left to display available values or settings. Set the desired setting value using the button. 4. To finish, select <EXIT> and press the SET button. the icon also has sub menus. To select a sub menu, select an item with the icon and MM `` AnpressitemthewithFunction Setup switch. `` An item with the --- icon is unavailable due to function settings. LENS Using this function, you can control the screen brightness. 1. When the SETUP menu screen is displayed, select <LENS> by using the Function Setup switch so that the arrow indicates <LENS>. 2. Adjust the focus automatically or manually when SETUP menu screen is displayed. • DC -- ONE-PUSH : Adjust the focus automatically. -- MANUAL : Adjust the zoom and focus manually using the Function Setup switch. 20_ Operating Your Camera MAIN SETUP ► 1. LENSDC 2. EXPOSURE 3. WHITE BAL ATW 4. SSDRON 5. BACKLIGHTOFF 6. SSNR3ON 7. DAY/NIGHTAUTO 8. SPECIAL 9. EXIT FUCUS ADJUST ► 1. ONE-PUSH 2. MANUAL 3. RETURNL EXPOSURE 2. Select a desired mode using the Function Setup switch. •• BRIGHTNESS : Adjust the screen brightness. •• SHUTTER : You can select the shutter. -- – – – : 1/30sec -- A.FLK : Select this when you experience picture flicker, this happen when there is a clash with the installed lighting frequency. -- ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter speed is automatically controlled depending on the ambient illumination of the subject. MAIN SETUP 1. LENSDC ► 2. EXPOSURE 3. WHITE BAL ATW 4. SSDRON 5. BACKLIGHTOFF 6. SSNR3ON 7. DAY/NIGHTAUTO 8. SPECIAL 9. EXIT EXPOSURE SETUP 1. BRIGHTNESS * .... .... .... ....50 ► 2. SHUTTERA.FLK 3. AGCHIGH 4. SENS-UPON 5. RETURN -- MANUAL : You can control shutter speed manually (1/30sec ~ 1/12,000sec) JJ `` When you use a DC lens, set the shutter mode to --- if color rolling occurs. `` Carefully position the camera when installing, since produced image quality might be poor if framing a bright light source while the shutter mode of EXPOSURE is set to AUTO. `` When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled. English _21 ● Operating Your Camera 1. When the SETUP menu screen is displayed, select <EXPOSURE> by using the Function Setup switch so that the arrow indicates <EXPOSURE> . Operating Your Camera •• AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen but the greater the noise. -- OFF : Not being used - Low : Allows automatic gain control from 5.3dB to 20dB. - Medium : Allows automatic gain control from 5.3dB to 26dB. - High : Allows automatic gain control from 5.3dB to 32dB. •• SENS-UP : When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated. -- OFF : Deactivates the SENS-UP function. -- AUTO : Activates the SENS-UP function. •• RETURN : Select this to save the changes in the EXPOSURE menu and return to the SETUP menu. the SET button while in AUTO mode to adjust the automatic scene accumulation multiplier JJ `` Press for low-illumination operation. (x2 ~ x60) `` The greater the video accumulation factor is, the brighter the screen is but the afterimage of a moving object grows accordingly. `` Although noise, spots, and whitish symptoms may occur in higher accumulation, this is normal. `` If the gain control (AGC) of EXPOSURE mode is set to OFF, SENS-UP mode is accordingly set to ‘- - -‘. 22_ Operating Your Camera White Bal (White Balance) Use the White Balance function to adjust the screen color. 2. Select a desired mode using the Function Setup switch. Select one of the following 5 modes, as appropriate for your purpose. MAIN SETUP 1. LENSDC 2. EXPOSURE ► 3. WHITE BAL ATW 4. SSDRON 5. BACKLIGHTOFF 6. SSNR3ON 7. DAY/NIGHTAUTO 8. SPECIAL 9. EXIT •• ATW : Select this when the color temperature is between 2,400˚K and 11,000˚K. •• OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K. (sodium light inclusion) •• INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K. •• MANUAL : Select this to fine-tune White WB MANUAL Balance manually. Set White Balance first by .... .... * .... ....552 ► 1. RED GAIN using the ATW or AWC mode. After that switch .... .... * .... ....560 2. BLUE GAIN to MANUAL mode, fine-tune the White Balance 3. RETURN and the Function Setup switch. •• AWC ➞ SET : To find the optimal luminance level for the current environment, point the camera towards a sheet of white paper and press the Function Setup switch. If the environment changes, readjust it. Balance may not work properly under the following conditions. In this case select the AWC JJ `` White mode. -- When the ambient illumination of the subject is dim. -- If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable. English _23 ● Operating Your Camera 1. When the SETUP menu screen is displayed, select <WHITE BAL>. by using the Function Setup switch so that the arrow indicates <WHITE BAL>. Operating Your Camera SSDR (Samsung Super Dynamic Range) SSDR illuminates darker areas of an image while retaining the same light level for brighter areas to even out the overall brightness of images with high contrast between bright and dark areas. 1. When the SETUP menu screen is displayed, select <SSDR> by using the Function Setup switch so that the arrow indicates <SSDR>. 2. Use the Function Setup switch to change the SSDR level in the sub menu according to the contrast between bright and dark areas. •• LeveL : Adjust the dynamic range level. •• D-RANGE : Select the amplitude area of the dynamic range. SSDR ON 24_ Operating Your Camera MAIN SETUP 1. LENSDC 2. EXPOSURE 3. WHITE BAL ATW ► 4. SSDRON 5. BACKLIGHTOFF 6. SSNR3ON 7. DAY/NIGHTAUTO 8. SPECIAL 9. EXIT SSDER SETUP .... .... * .... ....8 ► 1. LEVEL 2. D-RANGENARROW 3. RETURN SSDR OFF BACKLIGHT This camera is designed so that it delivers a distinctive subject and background at the same time, even when the subject is in backlight, by adopting a function of the proprietary WN2 DSP chip. 2. Select a desired mode using the Function Setup switch depending on the camera purpose. •• BLC : Enables a user to select a desired area on a picture and view that area more clearly. -- LEVEL : Adjust level of the BLC function. MAIN SETUP 1. LENSDC 2. EXPOSURE 3. WHITE BAL ATW 4. SSDRON ► 5. BACKLIGHTOFF 6. SSNR3ON 7. DAY/NIGHTAUTO 8. SPECIAL 9. EXIT -- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced. •• HLC (High Light Compensation) : If the scene contains extremely bright light areas such as; from car headlight, the light can mask out much of the on-screen detail. -- LEVEL : Adjust level of the HLC function. -- MASK COLOR/TONE : Change the color / brightness of the masking area. (Black, Red, Blue, Cyan, Magenta) -- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced. •• OFF : Not being used 3. Select a desired mode using the Function Setup switch. BLC SETUP ► 1. LEVELMIDDEL .... * .... .... ....30 2. TOP .... .... .... * ....75 3. BOTTOM .... * .... .... ....30 4. LEFT .... .... .... * ....75 5. RIGHT 6. RETURN HLC SETUP ► 1. LEVELMIDDEL 2. MASK TONE .... .... * .... ....5 .... * .... .... ....30 3. TOP .... .... .... * ....75 4. BOTTOM .... * .... .... ....30 5. LEFT .... .... .... * ....75 6. RIGHT 7. RETURN there can be a difference in the effectiveness of HLC according to the amount of light JJ `` Because area in the screen, optimize the installation angle for the best HLC performance. `` When dark, the HLC is only activated when a bright light exceeding a specific size. (In NIGHT ONLY mode). `` The HLC is not activated in day light or when bright light is not present at night. (In NIGHT ONLY mode). English _25 ● Operating Your Camera 1. When the SETUP menu screen is displayed, select <BACKLIGHT> by using the Function Setup switch so that the arrow indicates <BACKLIGHT>. Operating Your Camera SSNR3 This function reduces the background noise in a low luminance environment. 1. When the SETUP menu screen is displayed, select <SSNR3> by using the Function Setup switch so that the arrow indicates <SSNR3>. 2. Select a desired mode using the Function Setup switch. •• ON : Activates SSNR3 so that noise is reduced. •• OFF : Deactivates SSNR3. Noise is not reduced. MAIN SETUP 1. LENSDC 2. EXPOSURE 3. WHITE BAL ATW 4. SSDRON 5. BACKLIGHTOFF ► 6. SSNR3ON 7. DAY/NIGHTAUTO 8. SPECIAL 9. EXIT 3. Set the SSNR3 mode to <ON> and press the Function Setup switch. Then you can adjust the noise reduction level. JJ `` You cannot set the SSNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the ‘EXPOSURE’ menu is ‘OFF’. `` When adjusting the noise reduction level in the SSNR3 mode, remember that the higher the level set, the more the noise level will be reduced, as will the brightness of the image. DAY/NIGHT You can display pictures in color or in black and white. 1. When the SETUP menu screen is displayed, select <DAY/NIGHT> by using the Function Setup switch so that the arrow indicates <DAY/ NIGHT>. 2. Select a desired mode using the Function Setup switch according to the picture display you want. •• COLOR : The picture is always displayed in color. •• B/W : The picture is always displayed in black and white. 26_ Operating Your Camera MAIN SETUP 1. LENSDC 2. EXPOSURE 3. WHITE BAL ATW 4. SSDRON 5. BACKLIGHTOFF 6. SSNR3ON ► 7. DAY/NIGHTAUTO 8. SPECIAL 9. EXIT AUTO SETUP ► 1. COLOR B/W DWELL TIME 5 SEC DURATIONSLOW 2. COLOR B/W DWELL TIME 10 SEC DURATIONSLOW 3. SPECIAL -- DURATION : Adjust the brightness of the lighting where the mode switch occurs. •• EXTERN : Control the image modes of Color and B/W when an external controller is synchronized via the Alarm In port. AGC in the EXPOSURE menu is ‘OFF’, ‘---’ mode operates as selecting ‘AUTO’ mode cannot JJ `` When be selected. SPECIAL 1. When the SETUP menu screen is displayed, select <SPECIAL> by using the Function Setup switch so that the arrow indicates <SPECIAL>. 2. Select a desired mode using the Function Setup switch. MAIN SETUP 1. LENSDC 2. EXPOSURE 3. WHITE BAL ATW 4. SSDRON 5. BACKLIGHTOFF 6. SSNR3ON 7. DAY/NIGHTAUTO ► 8. SPECIAL 9. EXIT SPECIAL ► 1. CAM TITLE ON 2. IMAGE ADJ 3. MOTION DET ATW 4. PRIVACYON 5. COMM ADJ ON 6. LANGUAGEENGLISH 7. RESET 8. RETURN English _27 ● Operating Your Camera •• AUTO : The mode is switched to <COLOR> in a normal environment, but switches to <B/W> mode when ambient illumination is low. To set up the switching time for AUTO mode, press the Function Setup switch. -- DWELL TIME : You can select day/night switching delay time from. ➝ 5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s Operating Your Camera •• CAM TITLE : If you enter a title, the title will appear on the monitor. 1) If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates <CAM TITLE>. 2) Set it to <ON> by using the Function Setup switch. 3) Press the Function Setup switch. A B C NOP a b c n o p – . 1 ← → CAM TITLE SETUP D EF Q R S d e f q r s 2 3 C L R G T g t 4 H I J K L M UVW X Y Z h i j k l m u v w x y z 5 6 7 8 9 P O S E N D — — — — — — — — — — — — — — 4) Use the Function Setup switch to move to a desired letter and select the letter by pressing the Function Setup switch. Repeat this to enter multiple letters. You can enter up to 15 letters. 5) Enter a title, move the cursor to <POS> and press the Function Setup switch. The entered title appears on the screen. Select the position to display the title on the screen by using the Function Setup switch and press the Function Setup switch. When the position is determined, select <END> and press the Function Setup switch to return to the SPECIAL menu. ABCD ←→↑↓ to Locate, then SET the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you JJ `` When enter one. `` Only English is available in this mode. `` If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the Function Setup switch. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the Function Setup switch. 28_ Operating Your Camera 2) Select a desired mode using the Function Setup switch. -- Monitor : Please change the settings value of video appropriate to your monitor. •• LCD : Please select this menu item when using an LCD monitor. •• USER : Please use this menu item when using a monitor other than standard ones. You can change the gamma, PED level and color gain in the sub menus. SPECIAL 1. CAM TITLE ON ► 2. IMAGE ADJ 3. MOTION DET ATW 4. PRIVACYON 5. COMM ADJ ON 6. LANGUAGEENGLISH 7. RESET 8. RETURN IMAGE ADJ ► 1. MONTIORLCD 2. H-REVOFF 3. V-REVOFF 4. D-ZOOMOFF 5. SHARPNESSON 6. FONT COLOR WHITE 7. VIDEO FMT CVBS-NTSC 8. VIDEO SIZE 1080p 30 9. RETURN -- V-REV : You can flip the picture vertically on the screen. -- H-REV : You can flip the picture horizontally on the screen. -- D-ZOOM : You can use a digital zoom of x1 ~ x16. -- SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer. Adjust this value appropriately depending on the sharpness of the picture. -- FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue) -- VIDEO FORMAT : Sets the video output format of the C-Video port on the camera provided for test and installation. -- VIDEO SIZE : Sets the image resolution of the HD-SDI output of the camera. Select the desired setting and press the SET button. (1080i 50, 1080p 30, 720p 50, 720p 60, 1080i 60) -- RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to the SPECIAL menu. JJ ` If you increase the sharpness level excessively, the image may be displayed abnormally or it can cause a noise. English _29 ● Operating Your Camera •• IMAGE ADJ : 1) When the SPECIAL menu screen is displayed, select <IMAGE ADJ> by using the Function Setup switch so that the arrow indicates <IMAGE ADJ>. Operating Your Camera •• MOTION DET : This product has a feature that allows you to observe movement of objects in 4 different areas on the screen, and the words <MOTION DET> appear on the screen when movement is detected. You can monitor activity more efficient. 1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates <MOTION DET>. MOTION DET ► 1. AREAAREA1 2. MODEOFF 3. ALARM OUT OFF 4. TOP * .... .... .... ....60 .... .... * .... ....480 5. BOTTOM 6. LEFT * .... .... .... ....60 .... .... * .... ....900 7. RIGHT 8. SENSITIVITY .... .... * .... ....3 9. RETURN 2) Set up the mode using the Function Setup switch. -- AREA SEL : You can specify up to 4 motion detection areas to your preference. Select the desired type of motion detection area. According to the selected area type, top/bottom/left/right coordinates change. -- AREA: Specify the use of the selected motion detection area. If selected <ON>, the area is marked on the screen. -- ALARM OUT: Specify the use of output signal on motion detection. -- UP/DOWN/LEFT/RIGHT: Change the position of the selected area. -- SENSITIVITY : The lower the figure is, the higher the sensitivity is and the camera can track a slightest movement. -- RETURN : Save the motion detection settings and return to the OPERATION SETUP menu. detection area is marked only in MOTION DET menu, and not displayed on the monitoring JJ `` Motion screen. •• PRIVACY : Mask an area you want to hide on the screen. 1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates <PRIVACY>. 2) Set up the mode using the Function Setup switch. -- AREA : You can select up to 16 PRIVACY areas. PRIVACY AREA SETUP ► 1. AREAAREA1 2. AREA MODE OFF 3. MASK COLOR GRAY 4. TOP * .... .... .... ....80 .... * .... .... ....180 5. BOTTOM 6. LEFT * .... .... .... ....190 .... * .... .... ....290 7. RIGHT 8. RETURN -- MODE : Determines whether to use the area selected in the AREA. -- MASK COLOR : Determine area color. You can select Green, Red, Blue, Black, White, Gray. -- TOP/BOTTOM/LEFT/RIGHT : Adjust the size and position of the selected area. -- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL menu. 30_ Operating Your Camera 2) Set up the mode using the Function Setup switch. COMM SETUP ► 1. PROTOCOLSAMSUNG-T 2. CAM ID * .... .... .... ....1 3. BAUD RATE 9600 4. UART MODE 8-N-1 5. DISP ID OFF 6. RET PKT ENABLE 7. RETURN -- PROTOCOL : Select the communication PROTOCOL. (SAMSUNG-T, SAMSUNG-E, Pelco-D, Pelco-P, Bosch, Honeywell, Vicon, Panasonic, GE, AD) -- CAM ID : Determines the camera's identification number (between 0 and 255). -- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps. -- UART MODE : You can select NONE, EVEN or ODD for the parity bits. -- DISP ID : Display camera title on top left corner of the screen. -- RETURN DATA : Specify whether to return the same command to the controlling device when a control command is delivered to the camera. •• LANGUAGE : You can select the menu language according to your requirements. •• RESET : Resets the camera settings to the factory defaults. Communication, Language and Monitor settings are not initialized. •• RETURN : Select this to save the SPECIAL menu settings and return to the MAIN SETUP menu. EXIT Save the current settings and exit the MAIN SETUP menu. English _31 ● Operating Your Camera •• COMM ADJ (Communication Adjustment) : This function sets up the camera communication status when controlling the camera through an external control device. 1) When the SPECIAL menu screen is displayed, press the Function Setup switch so that the arrow indicates <COMM ADJ>. appendix Specification Items Video 1/3" Progressive Scan CMOS Total Pixels 2,010(H) x 1,108(V), 2.2M Pixels Effective Pixels 1,944(H) x 1,092(V), 2.1M Pixels Scanning System Progressiv Scan Min. Illumination Color : 1Lux @ F1.2, 0.017 Lux (Sens-up, 60x) B/W : 0.1 Lux @ F1.2, 0.0017 Lux ( Sens-up, 60x) S / N Ratio Lens Type Operational Description Video 50dB (AGC off, Weight on) Video Output SMPTE292M ( HD-SDI ), Monotoring CVBS Lens Type DC Auto Iris Lens 3~8.5mm (2.8X) Motorized Vari-focal Mount Type Board type On Screen Display Multi-language Support English, Korean, Japanese, Spanish, French, Portuguese, Chinese, German, Italian, Russian, Czech, Polish, Rumanian, Serbian, Swedish, Denish, Turkish, Thai, Taiwanese Camera Title Off / On (Displayed 15 characters) Day &Night Auto (ICR), Color, B/W , External Backlight Compensation Off / User BLC / HLC Contrast Enhancement SSDR ( Off / On ) Digital Noise Reduction SSNRⅢ ( Off / On ) Motion Detection 32_ appendix Motion Detection(Off/On) Items Environmenta Electrical Mechanica Privacy Masking Off / On (16 Rect-angle zones) Sens-up (Frame Integration) 2x ~ 60x Gain Control Off / Low / Middle / High White Balance ATW / Outdoor / Indoor / Manual / AWC (1,700K° ~ 11,000K°) Electronic Shutter Speed Esc / A.FLK / Manual Digital Zoom Off / On (1x ~ 16x) Reverse Off / H-Rev / V-Rev / HV-Rev Communication RS-485 Protocol RS-485 : SAMSUNG-T, SAMSUNG-E, Pelco-D, Pelco-P, Bosch, Honeywell, Vicon, Panasonic, GE, AD Operating Temperature 0°C ~ +50°C / ~ 90% RH / Humidity Input Voltage/Current Dual ( 24VAC±10% & 12VDC±10% ) Power Consumption Max. 6W Color / Material Body : Ivory / Plastic Dimension (ØxH) Ø133.0 x H129.4mm Weight 537g HD-SDI L-5C2V ( 75ohm ) Transmission L-6CHD ( 75 ohm ) Distance Max. 100~140m Max. 200m `` The maximum transferrable distance of HD-SDI video signal depends on the cable manufacturer or installation conditions. `` When a BNC cable adaptor is used to combine two or more BNC cables for distributed HD-SDI video transfer, make sure the impedance of the adaptor is 75Ω. Otherwise, the adaptor may cause shorter transfer distance or broken video transfer due to loss of transferred signal. English _33 ● appendix Operational Description appendix Product Overview Unit : mm (inch) 0 60(2.36") Ø9 129.4(5.09") Ø 133.0(5.24") Ø 100.4(3.94") 34_ appendix Troubleshooting PROBLEM yy When the camera’s HD-SDI BNC output is directly connected to the monitor’s BNC terminal: Make sure the monitor supports HD-SDI signal input. yy When the camera’s HD-SDI BNC output is connected to the DVR: Make sure the DVR supports HD-SDI signal input. yy HD-SDI output is converted into other format such as DVI and VGA by using video converter: Make sure the converter’s HD-SDI input format supports the product’s output video format. yy Is lens stained with dirt? Clean your lens with soft, clean cloth. The image on the screen is dim. yy Set the monitor to the proper condition. The image on the screen is dark. yy Adjust the contrast feature of the monitor. The camera is not working properly, and the surface of the camera is hot. The SENS-UP function does not work. The Motion Detection function does not work. Color is not correct. yy If the camera is exposed to very strong light, change the camera position. yy Check that you have properly connected the camera to an appropriate power source. yy Check that AGC of EXPOSURE SETUP menu is ‘OFF’. yy Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’. yy Check the setting of WHITE BAL SETUP menu . yy Ensure the camera is not pointing towards the sun. yy Is the camera framing the sun or other bright light source? The screen flickers continually. RS-485 communication is not available. yy HD-SDI video may not appear to be normal if distance exceeds the maximum transferrable distance. yy When a BNC cable adaptor is used to combine two or more BNC cables for distributed HD-SDI video transfer, make sure the impedance of the adaptor is 75Ω. Otherwise, it may cause shorter transfer distance or broken video transfer. y Check RS-485 communication settings. English _35 ● appendix Nothing appears on the screen. SOLUTION yy Check that the power cord and line connection between the camera and monitor are properly connected. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Samsung Techwin cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products. The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly products, and indicates that the product satisfies the EU RoHS Directive. Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. Correct disposal of batteries in this product (Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health or the environment. To protect natural resources and to promote material reuse, please separate batteries from other types of waste and recycle them through your local, free battery return system. SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660 Toll Free : +1-877-213-1222 Direct : +1-201-325-6920 Fax : +1-201-373-0124 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com SAMSUNG TECHWIN EUROPE LTD. Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS TEL : +44-1932-45-5300 FAX : +44-1932-45-5325