Download Metra Dash kit
Transcript
INSTALLATION INSTRUCTIONS FOR PART 99-7880B APPLICATIONS Honda Odyssey 2011-up 99-7880B KIT FEATURES • ISO DIN head unit provision with pocket • DDIN head unit provisions • Painted matte black to match factory finish KIT COMPONENTS • A) Radio Housing Trim Panel • B) Storage Pocket • C) (4) #8 x 3/8” Phillips screws A B C WIRING & ANTENNA CONNECTIONS (Sold Separately) Wiring Harness: • 70-1729 - Honda harness 2008-up • 70-1730 - Honda Premium Audio Integration harness 2008-up Antenna Adapter: • 40-HD11 - Honda antenna adapter 2009-up TOOLS REQUIRED Panel Removal Tool • Phillips Screwdriver • Socket Wrench METRA. THE WORLD’S BEST KITS.™ metraonline.com 1-800-221-0932 © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION 99-7880B Table of Contents Dash Disassembly – Honda Odyssey 2011-up 3-4 Kit Assembly – ISO DIN head unit provisions – Double DIN head unit provisions 5 6 Caution Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition. *NOTE: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians 99-7880B Dash Disassembly 1. Unsnap and remove trim around the shifter. (Figure A) 2. Unsnap and remove the passenger side trim panel above the glove box. (Figure B) 3. Unsnap and remove the climate control panel from the controls over to the passenger side. (Figure C) Continued on next page (Figure A) (Figure B) (Figure C) 3 99-7880B Dash Disassembly 4. Remove four Phillips screws from the upper part of the lower center console and pull back the upper part enough to remove the radio. (Figure D) 5. Remove four screws and remove the radio. Remove the factory brackets for use in kit assembly. (Figure E) 6. Remove two screws and remove the factory pocket from the top of the radio. (Figure F) 7. Attach the factory pocket to the Metra radio housing trim panel using the factory hardware. (Figure G) (Figure E) Continue to kit assembly (Figure F) (Figure D) (Figure G) 4 Kit Assembly 99-7880B ISO DIN head unit provisions 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2. Mount the factory radio brackets to the head unit with the screws supplied with the unit. (Figure A) 3. Mount the Metra pocket to the brackets using the supplied screws. (Figure A) (Figure A) 4. Mount the radio assembly into the dash and snap the radio housing panel over the radio asembly. (Figure B) 5. Reassemble dash in reverse order of disassembly. (Figure B) 5 Kit Assembly 99-7880B Double DIN head unit provisions 1. Locate the factory wiring harness and antenna plug in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Mount the factory radio brackets to the new head unit with the screws supplied with the unit. (Figure A) 3. Mount the radio assembly into the dash and snap the radio housing panel over the radio asembly. (Figure B) (Figure A) 4. Reassemble dash in reverse order of disassembly. (Figure B) 6 Notes REV. 8/15/11 INSTALLATION INSTRUCTIONS FOR PART 99-7880B METRA. THE WORLD’S BEST KITS.™ metraonline.com 1-800-221-0932 © COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION