Download Lian Li PC-V1110 computer case
Transcript
Case components: Power LED HDD LED Front door with lock 5.25” mounting bracket Power switch button Reset switch button Front panel 14cm fan with filter Metal casters Door key is attach to the accessory box Multi-media port Side panel lock 3-speed fan controller 12cm fan 12cm fan VGA card pillar Air vent 14cm fan Removable PSU tray HDD module Brake for wheels Support liquid cooling system Side panels installation 2 1 Loose the screw and pull the latch to release the side panel. Remove the side panel. Adding a lock to secure the hardware. Loosen the screws to remove dust-free cover for water tube openings. Removable fan filter 2 Removable air filter 1 Push to release Removable air filter 1. Fasten the HDD screws with anti-vibration rubber rings to the HDD. 2. Slide the HDD into the HDD cage with the anti-vibration kit. Loosing the two thumb screws on the fan module to release. Press down the HDD into the slots to secure. Note: Adding extra screw to the HDD cage for extra security. Hardware list Buzzer(1) (56) Extension cable 12V(1) for power supply to M/B Stand off bolt(16) Thumb screw(26) & rubber ring(26) for fix HDD Power supply holder kit(2) Mounting bracket for SSI CEB/EEB for stand off PCI card holder-S(3) PCI card holder-L(4) Thumb screw(7) for PCI card holder Chip set cooler(1)+ themb screw(2) to mount on PCI card holder Rubber protectors(4) for wheels 1 for stand off bolt Thumb screw(6) for HDD extra fixing (6) 2 for cable management C50.V1110.00E-1 3-speed fan adjustable device 3 for SSI CEB/EEB 1 The oval hole on M/B tray designed for special server boards, please use the nut to hold the copper bolt in place. 2 Secure the stand off bolts on the M/B tray which match with the M/B fix points, place the M/B on the copper bolt, fasten the screws to secure. Loosing two thumb screws to release the M/B tray. PSU tray installation Extension cable for 12V PSU to M/B VGA Card Pillar Installation Guide 2 1 3 9 7 Black(GND) 5 Green 3 White 1 Red KEY10 Black(GND) 8 Green 6 White 4 Red 2 9 7 Black(GND) 5 Green 3 White 1 Red 2 Red(MIC) 4 Brown(MIC-PWE) 6 Yellow(R-OUT) 8 10 Blue(L-OUT) EAR MIC USB KEY 10 Black(GND) 8 Green 6 White 4 Red 2 1 3 5 7 9 USB USB 9 Green(SENSE2 RETUR) 7 KEY 5 Orange(SENSE1 RETUR) 3 Black(PRESENCE) 1 Black(GND) HD AUDIO AC'97 Blue(PORT2 L) 10 Black(SENSE SEND) 8 Yellow(PORT2 R) 6 Brown(PORT1 R) 4 Red(PORT1 L) 2 Black(AGND) NC Yellow(R-RET) KEY Blue(L-RET) 4 USB 9 7 5 3 1 Black(GND) White(+12V) Red(TPB-) Black(VG) Orange(TPA-) 1394 IEEE1394 Black(KEY) 10 White(+12V) 8 Green(TPB+) 6 Black(VG) 4 Blue(TPA+) 2 E-SATA Connector SATA Cable C50.V1110.00E-2 Chip set cooler installation Aluninum wheel brake Rubber protector for aluminum wheels Adjustment for door swing direction Take the spindles off the top and bottom plate Loose the screws on the top panel plate as show in the image above. A Remove the door, and place the door on a table top. Loose the nut to uninstall the lock B ▼ Face to the top of the front panel. When lock at A side ▼ Face to the top of the front panel. Swap the hinge and door stop as show as the image above When lock at B side 1. Secure all screws, and lock 2. Check the lock working mechanism swing the right direction Reverse the step 2 and step 1 to secure the door panel. Finish. C50.V1110.00E-3