Download HMD-A400

HMD-A400
SERVICE MANUAL
US Model
Canadian Model
Chassis No. SCC-L35A-A
H1CHASSIS
SPECIFICATIONS
CRT
0.24 mm aperture grille pitch (center)
19 inches measured diagonally
90-degree deflection
FD Trinitron
Approx. 365 × 274 mm (w/h)
(14 3/8 × 10 7/8 inches)
18.0" viewing image
Viewable image size
Resolution
Maximum
Horizontal: 1600 dots
Vertical: 1200 lines
Recommended Horizontal: 1280 dots
Vertical: 1024 lines
Standard image area
Approx. 352 × 264 mm (w/h)
(13 7/8 × 10 1/2 inches)
Deflection frequency*
Horizontal: 30 to 86 kHz
Vertical: 48 to 120 Hz
AC input voltage/current 100 – 120 V, 50 – 60 Hz, 2.3 A
Power consumption
Max. 150 W
Dimensions
Approx. 497 × 458 × 469 mm
(w/h/d)
(19 5/8 × 18 1/8 × 18 1/2 inches)
Mass
Approx. 26 kg (57 lb 5 oz)
Plug and Play
DDC2B/DDC2Bi
* Recommended horizontal and vertical timing condition
• Horizontal sync width should be more than 1.0 µsec.
• Horizontal blanking width should be more than 3.0 µsec.
• Vertical blanking width should be more than 500 µsec.
Design and specifications are subject to change without notice.
TRINITRON COLOR COMPUTER DISPLAY
®
HMD-A400
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps,
and mounting hardware have been replaced. Be absolutely
certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious
signs of deterioration. Point them out to the customer and
recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend
the replacement of any such line cord to the customer.
7. Check the B+ and HV to see if they are specified values.
Make sure your instruments are accurate; be suspicious of
your HV meter if sets always have low HV.
8. Check the antenna terminals, metal trim, “metallized”
knobs, screws, and all other exposed metal parts for AC
Leakage. Check leakage as described below.
To Exposed Metal
Parts on Set
0.15 µF
1.5 kΩ
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500
microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or
RCA WT-540A. Follow the manufacturers’ instructions to
use these instruments.
2. A battery-operated AC milliammeter. The Data Precision
245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are
examples of a passive VOMs that are suitable. Nearly all
battery operated digital multimeters that have a 2 V AC
range are suitable. (See Fig. A)
WARNING!!
NEVER TURN ON THE POWER IN A CONDITION IN
WHICH THE DEGAUSS COIL HAS BEEN REMOVED.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY SHADING AND MARK
0 ON THE SCHEMATIC DIAGRAMS, EXPLODED
VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR
SAFE OPERATION. REPLACE THESE COMPONENTS
WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. CIRCUIT ADJUSTMENTS THAT ARE CRITICAL FOR SAFE OPERATION
ARE IDENTIFIED IN THIS MANUAL. FOLLOW THESE
PROCEDURES WHENEVER CRITICAL COMPONENTS
ARE REPLACED OR IMPROPER OPERATION IS SUSPECTED.
AVERTISSEMENT!!
NE JAMAIS METTRE SOUS TENSION QUAND LA
BOBINE DE DEMAGNETISATION EST ENLEVÉE.
ATTENTION AUX COMPOSANTS RELATIFS À LA
SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE TRAME ET
UNE MARQUE 0 SONT CRITIQUES POUR LA SÉCURITÉ.
NE LES REMPLACER QUE PAR UNE PIÈCE PORTANT LE
NUMÉRO SPECIFIÉ. LES RÉGLAGES DE CIRCUIT DONT
L’IMPORTANCE EST CRITIQUE POUR LA SÉCURITÉ DU
FONCTIONNEMENT SONT IDENTIFIÉS DANS LE
PRÉSENT MANUEL. SUIVRE CES PROCÉDURES LORS
DE CHAQUE REMPLACEMENT DE COMPOSANTS CRITIQUES, OU LORSQU’UN MAUVAIS FONCTIONNEMENT
EST SUSPECTÉ.
–2–
HMD-A400
POWER SAVING FUNCTION
This monitor meets the power-saving guidelines set by VESA,
ENERGY STAR, and NUTEK. If no signal is received by the
monitor from the connected computer, the monitor will
automatically reduce power consumption as shown below.
Power mode
Power
consumption*
! (power)
indicator
normal
operation
≤ 150 W
green
active off**
≤3W
orange
power off
0W
off
* Figures reflect power consumption when no USB compatible
peripherals are connected to the monitor.
** When your computer enters the “active off” mode, the input signal is
cut and NO INPUT SIGNAL appears on the screen. After 20 seconds,
the monitor enters the power saving mode.
DIAGNOSIS
Failre
HV or +B failure or Hstop
Vstop
ABL protector
Aging / Self Test
Self Test (OSD Color Bar)
Power LED
Orange →
(0.5 sec)
Orange →
(1.5 sec)
Orange →
(0.5 sec)
Orange →
(0.5 sec)
Off
(0.5 sec)
Off
(0.5 sec)
Off
(1.5 sec)
Off
→
Green →
Off
(0.5 sec)
(0.5 sec)
(0.5 sec)
: During Power Save, press “CONT” (,) key for longer than 2 second.
–3–
HMD-A400
TIMING SPECIFICATION
MODE AT PRODUCTION
RESOLUTION
CLOCK
— HORIZONTAL —
H-FREQ
H. TOTAL
H. BLK
H. FP
H. SYNC
H. BP
H. ACTIV
— VERTICAL —
V. FREQ(HZ)
V. TOTAL
V. BLK
V. FP
V. SYNC
V. BP
V. ACTIV
— SYNC —
INT(G)
EXT(H/V)/POLARITY
EXT(CS)/POLARITY
INT/NON INT
MODE AT PRODUCTION
RESOLUTION
CLOCK
— HORIZONTAL —
H-FREQ
H. TOTAL
H. BLK
H. FP
H. SYNC
H. BP
H. ACTIV
— VERTICAL —
V. FREQ(HZ)
V. TOTAL
V. BLK
V. FP
V. SYNC
V. BP
V. ACTIV
— SYNC —
INT(G)
EXT(H/V)/POLARITY
EXT(CS)/POLARITY
INT/NON INT
MODE 1
640 X 480
25.175 MHz
MODE 2
640 X 480
36.000 MHz
MODE 3
720 X 400
28.321 MHz
MODE 4
800 X 600
56.250 MHz
MODE 5
832 X 624
57.283 MHz
31.469 kHz
usec
31.778
6.356
0.636
3.813
1.907
25.422
43.269 kHz
usec
23.111
5.333
1.556
1.556
2.222
17.778
31.468 kHz
usec
31.779
6.356
0.636
3.813
1.907
25.423
53.674 kHz
usec
18.631
4.409
0.569
1.138
2.702
14.222
49.725 kHz
usec
20.111
5.586
0.559
1.117
3.910
14.524
59.940 Hz
lines
525
45
10
2
33
480
85.008 Hz
lines
509
29
1
3
25
480
70.084 Hz
lines
449
49
12
2
35
400
85.061 Hz
lines
631
31
1
3
27
600
74.550 Hz
lines
667
43
1
3
39
624
NO
YES N/N
NO
NON INT
NO
YES N/N
NO
NON INT
NO
YES N/P
NO
NON INT
NO
YES N/P
NO
NON INT
NO
YES N/N
NO
NON INT
MODE 6
1024 X 768
94.500 MHz
MODE 7
1152 X 870
100.000 MHz
MODE 8
1280 X 1024
135.000 MHz
MODE 9
1600 X 1200
162.000 MHz
68.677 kHz
usec
14.561
3.725
0.508
1.016
2.201
10.836
68.681 kHz
usec
14.560
3.040
0.320
1.280
1.440
11.520
79.976 kHz
usec
12.504
3.022
0.119
1.067
1.837
9.481
75.000 kHz
usec
13.333
3.457
0.395
1.185
1.877
9.877
84.997 Hz
lines
808
40
1
3
36
768
75.062 Hz
lines
915
45
3
3
39
870
75.025 Hz
lines
1066
42
1
2
38
1024
60.000 Hz
lines
1250
50
1
3
46
1200
NO
YES P/P
NO
NON INT
NO
YES N/N
NO
NON INT
NO
YES P/P
NO
NON INT
NO
YES P/P
NO
NON INT
2001.2.23 VER.
–4–
HMD-A400
TABLE OF CONTENTS
Section
Title
Page
1. GENERAL .................................................................. 1-1
2. DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
Bucket Assembly Removal ................................. 2-1
A Board Removal ................................................ 2-1
D Board Removal ................................................ 2-2
Service Position .................................................... 2-3
H Board Removal ................................................. 2-4
Picture Tube Removal .......................................... 2-4
Harness Location .................................................. 2-5
3. SAFETY RELATED ADJUSTMENT ............. 3-1
4. ADJUSTMENTS ...................................................... 4-1
5. DIAGRAMS
5-1.
5-2.
5-3.
5-4.
(1)
(2)
(3)
5-5.
Block Diagrams ................................................... 5-1
Frame Schematic Diagram .................................. 5-5
Circuit Boards Location ...................................... 5-6
Schematic Diagrams and Printed Wiring Boards .. 5-7
Schematic Diagram of H Board ......................... 5-8
Schematic Diagram of A Board ......................... 5-9
Schematic Diagrams of
D (a, b, c, d, e, f) Board .................... 5-15
Semiconductors .................................................. 5-27
6. EXPLODED VIEWS
6-1.
6-2.
6-3.
Chassis ................................................................. 6-1
Picture Tube ........................................................ 6-2
Packing Materials ................................................ 6-3
7. ELECTRICAL PARTS LIST ............................ 7-1
–5–
SECTION 1
GENERAL
Use of the stand
Precautions
Warning on power connections
• Use the supplied power cord. If you use a different power cord,
be sure that it is compatible with your local power supply.
For the customers in the U.S.A.
If you do not use the appropriate cord, this monitor will not
conform to mandatory FCC standards.
Insert the supplied stand into the groove to adjust the angle of the
monitor. You can use the stand in either the vertical or horizontal
position. If you do not need the stand for this purpose, you can use
it as a convenient CD rack.
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remein as in the manual.
Identifying parts and controls
See the pages in parentheses for further details.
Front
Rear
Example of plug types
MENU
for 100 to 120 V AC
• Before disconnecting the power cord, wait at least 30 seconds
after turning off the power to allow the static electricity on the
screen’s surface to discharge.
• After the power is turned on, the screen is demagnetized
(degaussed) for about 5 seconds. This generates a strong
magnetic field around the screen which may affect data stored
on magnetic tapes and disks placed near the monitor. Be sure to
keep magnetic recording equipment, tapes, and disks away
from the monitor.
1-1
The equipment should be installed near an easily accessible
outlet.
Installation
Do not install the monitor in the following places:
• on surfaces (rugs, blankets, etc.) or near materials (curtains,
draperies, etc.) that may block the ventilation holes
• near heat sources such as radiators or air ducts, or in a place
subject to direct sunlight
• in a place subject to severe temperature changes
• in a place subject to mechanical vibration or shock
• on an unstable surface
• near equipment which generates magnetism, such as a
transformer or high voltage power lines
• near or on an electrically charged metal surface
1 Control button (page 9)
The control button is used to display the menu and make
adjustments to the monitor, including brightness and contrast
adjustments.
2 ! (power) switch and indicator (pages 6, 12, 15)
This button turns the monitor on and off. The power indicator
lights up in green when the monitor is turned on, and either
flashes in green and orange, or lights up in orange when the
monitor is in power saving mode.
3 AC IN connector (page 6)
This connector provides AC power to the monitor.
4 Video input connector (HD15) (page 6)
This connector inputs RGB video signals (0.700 Vp-p,
positive) and sync signals.
1 2 3 4 5
6 7 8 9 10
11 12 13 14 15
Pin No.
Signal
1
Red
2
Green
3
Blue
4
ID (Ground)
5
DDC Ground*
6
Red Ground
7
Green Ground
8
Blue Ground
9
DDC + 5V*
Maintenance
10
Ground
• Clean the screen with a soft cloth. If you use a glass cleaning
liquid, do not use any type of cleaner containing an anti-static
solution or similar additive as this may scratch the screen’s
coating.
• Do not rub, touch, or tap the surface of the screen with sharp or
abrasive items such as a ballpoint pen or screwdriver. This type
of contact may result in a scratched picture tube.
• Clean the cabinet, panel and controls with a soft cloth lightly
moistened with a mild detergent solution. Do not use any type
of abrasive pad, scouring powder or solvent, such as alcohol or
benzene.
11
ID (Ground)
Transportation
When you transport this monitor for repair or shipment, use the
original carton and packing materials.
4
12
Bi-Directional Data (SDA)*
13
H. Sync
14
V. Sync
15
Data Clock (SCL)*
US
* DDC (Display Data Channel) is a standard of VESA.
5 USB (universal serial bus) downstream connectors
(page 7)
Use these connectors to link USB peripheral devices to the
monitor.
6 USB (universal serial bus) upstream connector
(page 7)
Use this connector to link the monitor to a USB compliant
computer.
5
Step 2: Connect the power cord
Setup
Before using your monitor, check that the following accessories
are included in your carton:
• Power cord (1)
• USB cable (1)
• Monitor stand (1)
• Warranty card (1)
• Notes on cleaning the screen’s surface (1)
• This instruction manual (1)
With the monitor and computer switched off, first connect the
power cord to the monitor, then connect it to a power outlet.
Connecting Universal Serial Bus
(USB) compliant peripherals
Your monitor has one upstream USB connector (on the rear
panel) and four downstream USB connectors (two on both the left
and right sides). They provide a fast and easy way to connect USB
compliant peripheral devices (such as keyboards, mice, printers
and scanners) to your computer using a standardized USB cable.
To use your monitor as a hub for your peripheral devices, connect
the USBs as illustrated below.
Selecting the on-screen menu
language (LANGUAGE/
INFORMATION)
English, French, German, Italian, Spanish, Dutch, Swedish,
Russian and Japanese versions of the on-screen menus are
available. The default setting is English.
1 Press the center of the control button.
See page 9 for more information on using the control button.
to AC IN
Step 1: Connect your monitor to
your computer
Turn off the monitor and computer before connecting.
Note
Do not touch the pins of the video cable connector as this might bend the
pins.
x Connecting to an IBM PC/AT or compatible
computer
MENU
EX I T
P I CTURE E F F ECT
S I Z E / CENT ER
GEOME TRY
CONVERGENCE
SCREEN
COLOR
L ANGUAGE / I NFORMA T I ON
RESE T
SE L ECT
to a power outlet
power cord (supplied)
MENU
Step 3: Turn on the monitor and
computer
2 Move the control button m/M to highlight
LANGUAGE/INFORMATION and press the center
of the control button again.
First turn on the monitor, then turn on the computer.
to USB compliant
peripheral devices
1-2
The installation of your monitor is complete.
If necessary, use the monitor’s controls to adjust the picture.
If no picture appears on your screen
to video output
IBM PC/AT or
compatible computer
x Connecting to a Macintosh or compatible
computer
You will need a Macintosh adapter (not supplied).
• Check that the monitor is correctly connected to the computer.
• If NO INPUT SIGNAL appears on the screen, confirm that
your computer’s graphic board is completely seated in the
correct bus slot.
• If you are replacing an old monitor with this model and OUT
OF SCAN RANGE appears on the screen, reconnect the old
monitor. Then adjust the computer’s graphic board so that the
horizontal frequency is between 30 – 86 kHz, and the vertical
frequency is between 48 – 120 Hz.
For more information about the on-screen messages, see “Trouble
symptoms and remedies” on page 13.
Setup on various OS (Operating System)
This monitor complies with the “DDC” Plug & Play standard and
automatically detects all the monitor’s information. No specific driver
needs to be installed to the computer.
If you connect the monitor to your PC, and then boot your PC for the first
time, the setup Wizard may be displayed on the screen. Click on “Next”
several times according to the instructions from the Wizard until the Plug
& Play Monitor is automatically selected so that you can use this monitor.
Macintosh adapter (not supplied)
Macintosh or
compatible
computer
6
to a USB compliant
computer
to USB compliant
peripheral devices
LANGUAGE / I NFORMAT I ON
ENGL I SH
DEUT SCH
ESPAÑOL
SVENSKA
1 Turn on the monitor and computer.
SE L ECT
2 Connect your computer to the square upstream
connector using the supplied USB cable.
For customers using Windows
If a message appears on your screen, follow the on-screen
instructions and select Generic USB Hub as the default setting.
3 Connect your USB compliant peripheral devices to
the rectangular downstream
USB connectors.
Notes
• Not all computers and/or operating systems support USB
configurations. Check your computer’s instruction manual to see if you
can connect USB devices.
• In most cases, USB driver software needs to be installed on the host
computer. Refer to the peripheral device’s instruction manual for
further details.
• The monitor functions as a USB hub as long as the monitor is either
“on” or in power saving mode.
• If you connect a keyboard or mouse to the USB connectors and then
boot your computer for the first time, the peripheral devices may not
function. First connect the keyboard and mouse directly to the
computer and set up the USB compliant devices. Then connect them to
this monitor.
• Do not lean on the monitor when plugging in the USB cables. The
monitor may suddenly shift and cause injury.
US
FRANÇA I S
I T A L I ANO
NEDER L AN D S
EX I T
MENU
3 Move the control button m/M to select
. Then move
the control button </, to select a language.
• ENGLISH
• FRANÇAIS: French
• DEUTSCH: German
• ITALIANO: Italian
• ESPAÑOL: Spanish
• NEDERLANDS: Dutch
• SVENSKA: Swedish
•
: Russian
•
: Japanese
To close the menu
Press the center of the control button once to return to the main MENU,
and twice to return to normal viewing. If no buttons are pressed, the menu
closes automatically after about 30 seconds.
To reset to English
See “Resetting the adjustments (RESET)” on page 11.
For customers using Windows NT4.0
Monitor setup in Windows NT4.0 does not use the display driver. Refer
to the Windows NT4.0 instruction manual for further details on adjusting
the resolution, refresh rate, and number of colors.
to video output
7
Customizing Your Monitor
You can make numerous adjustments to your monitor using the
on-screen menu.
6 SCREEN (page 11)
Select the SCREEN menu to
degauss the screen and adjust
the moire cancellation level.
x Using the control button
SCREEN
Press the center of the control button to display the main
MENU on your screen.
ON
SE L ECT
Navigating the menu
Press the center of the control button to display the main MENU
on your screen. See page 9 for more information on using the
control button.
7 COLOR (page 11)
Select the COLOR menu to
adjust the picture’s color
temperature. You can use this
to match the monitor’s colors
to a printed picture’s colors.
MENU
EX I T
P I CTURE E F F ECT
S I Z E / CENT ER
GEOME TRY
CONVERGENCE
SCREEN
COLOR
L ANGUAGE / I NFORMA T I ON
RESE T
SE L ECT
EX I T
50
50
50
SE L ECT
BR I GHTNESS / CONTRAST
LANGUAGE / I NFORMAT I ON
ENGL I SH
DEUT SCH
ESPAÑOL
SVENSKA
FRANÇA I S
I T A L I ANO
NEDER L AN D S
SE L ECT
26
2 Select the menu you want to adjust.
2 Move the control button m/M to adjust the
EX I T
brightness (
(6).
RESE T
MOD E
ALL
MENU
MENU
1-3
P I CTURE EFFECT
S T ANDARD
DYNAM I C
Move the control button left (<) or right (,) to make the
adjustment.
The horizontal and vertical frequencies of the current input signal
are displayed under the BRIGHTNESS/CONTRAST menu. If the
signal matches one of this monitor’s factory preset modes, the
resolution is also displayed.
The main MENU appears on the screen.
2 Move the control button to highlight PICTURE
MENU
EX I T
S I ZE / CENTER
H - C E N T ER
26
EX I T
the resolution
of the current
input signal
26
H : 6 8 . 7 kHz V : 8 5Hz
1 0 2 4X7 6 8
the horizontal
and vertical
frequencies of
the current
input signal
US
The PICTURE EFFECT feature allows you to select the most
appropriate picture mode from among two preset modes
maximum performance.
1 Press the center of the control button.
BR I GHTNESS / CONTRAST
SE L ECT
Adjusting the picture quality
(PICTURE EFFECT)
3 Adjust the menu.
x Displaying the current input signal
4 Close the menu.
EFFECT and press the center of the control button
again .
The PICTURE EFFECT menu appears on the screen.
3 Move the control button m/M to select the desired
Press the center of the control button once to return to the
main MENU, and twice to return to normal viewing. If no
buttons are pressed, the menu closes automatically after about
30 seconds.
picture mode.
Select
For
STANDARD
images with high contrast and
brightness. Choose this mode for
commonly used applications, such as
spreadsheets, word processing,
E-mail, or WEB surfing.
DYNAMIC
extremely vivid and photo-realistic
images. Brighter than “STANDARD”
mode, choose this for intense graphic
applications such as games, DVD
playback, or entertainment software.
GEOMETRY
RO T A T I ON
26
SE L ECT
EX I T
MENU
8
), and </, to adjust the contrast
RESET
EX I T
SE L ECT
5 CONVERGENCE
(page 10)
Select the CONVERGENCE
menu to adjust the picture’s
horizontal and vertical
convergence.
26
H : 6 8 . 7 kHz V : 8 5Hz
1 0 2 4X7 6 8
Highlight the desired menu by moving the control button up
(M), down (m), and left (<) or right (,).
The menu automatically disappears after about 3 seconds.
26
4 GEOMETRY (page 10)
Select the GEOMETRY
menu to adjust the picture’s
rotation and shape.
The BRIGHTNESS/CONTRAST menu appears on the
screen.
EX I T
MENU
9 RESET (page 11)
Select the RESET menu to
reset the adjustments.
1 EXIT
Select EXIT to close the menu.
3 SIZE/CENTER (page 10)
Select the SIZE/CENTER
menu to adjust the picture’s
centering, size or zoom.
Brightness and contrast adjustments are made using a separate
BRIGHTNESS/CONTRAST menu.
These settings are stored in memory for all input signals.
1 Move the control button in any direction.
USER 5000 K 6500 K 9300 K
R
G
B
Use the control button to select one of the following menus.
2 PICTURE EFFECT
(page 9)
Select the PICTURE
EFFECT menu to choose the
most appropriate preset
picture mode.
Adjusting the brightness and
contrast
COLOR
8 LANGUAGE/
INFORMATION
(page 7, 14)
Select the LANGUAGE/
INFORMATION menu to
choose the on-screen menu’s
language and display this
monitor’s information box.
MENU
1 Display the main MENU.
D EGA U S S
CONVERGENCE
x Resetting the adjustments
You can reset the adjustments using the RESET menu. See
page 11 for more information on resetting the adjustments.
26
SE L ECT
EX I T
9
Adjusting the centering of the
picture (CENTER)
Adjusting the shape of the picture
(GEOMETRY)
Adjusting the color of the picture
(COLOR)
This setting is stored in memory for the current input signal.
The GEOMETRY settings allow you to adjust the rotation and
shape of the picture.
The
(ROTATION) setting is stored in memory for all input
signals. All other settings are stored in memory for the current
input signal.
The COLOR settings allow you to adjust the picture’s color
temperature by changing the color level of the white color field.
Colors appear reddish if the temperature is low, and bluish if the
temperature is high. This adjustment is useful for matching the
monitor’s colors to a printed picture’s colors.
This setting is stored in memory for all input signals.
1 Press the center of the control button.
The main MENU appears on the screen.
2 Move the control button m/M to highlight
SIZE/
CENTER and press the center of the control button
again.
The SIZE/CENTER menu appears on the screen.
3 First move the control button m/M to select
(H-CENTER) for horizontal adjustment, or
(V-CENTER) for vertical adjustment. Then move
the control button </, to adjust the centering.
1 Press the center of the control button.
The main MENU appears on the screen.
The main MENU appears on the screen.
2 Move the control button m/M to highlight
GEOMETRY and press the center of the control
button again.
The GEOMETRY menu appears on the screen.
3 First move the control button m/M to select the
Adjusting the size of the picture
(SIZE)
desired adjustment item. Then move the control
button </, to make the adjustment.
Select
This setting is stored in memory for the current input signal.
1 Press the center of the control button.
The main MENU appears on the screen.
2 Move the control button m/M to highlight
1-4
SIZE/
CENTER and press the center of the control button
again.
The SIZE/CENTER menu appears on the screen.
(ROTATION)
To
rotate the picture
(PIN)
expand or contract the picture sides
(PIN BALANCE)
shift the picture sides to the left or
right
(KEY)
adjust the picture width at the top of
the screen
(KEY BALANCE) shift the picture to the left or right at
the top of the screen
3 First move the control button m/M to select
(H-SIZE) for horizontal adjustment, or
(V-SIZE) for vertical adjustment. Then move the
control button </, to adjust the size.
Enlarging or reducing the picture
(ZOOM)
This setting is stored in memory for the current input signal.
1 Press the center of the control button.
SIZE/
CENTER and press the center of the control button
again.
The SIZE/CENTER menu appears on the screen.
3 Move the control button m/M to select
(ZOOM),
and move </, to enlarge or reduce the picture.
2 Move the control button m/M to highlight
COLOR
and press the center of the control button again.
The COLOR menu appears on the screen.
3 Move the control button </, to select a color
temperature.
The preset color temperatures are 5000K, 6500K, and 9300K.
Since the default setting is 9300K, the whites will change
from a bluish hue to a reddish hue as the temperature is
lowered to 6500K and 5000K.
Adjusting the convergence
(CONVERGENCE)
First move the control button </, to select USER. Then
move the control button m/M to select R (red), G (green), or
B (blue) and move the control button </, to make the
adjustment.
COLOR
USER 5000 K 6500 K 9300 K
R
G
B
50
50
50
EX I T
If you fine tune the color temperature, the new color settings
are stored in memory and recalled whenever you select
USER.
The CONVERGENCE settings allow you to adjust the quality of
the picture by controlling the convergence. The convergence
refers to the alignment of the red, green, and blue color signals.
If you see red or blue shadows around letters or lines, adjust the
convergence.
These settings are stored in memory for all input signals.
You can manually degauss (demagnetize) the screen, and adjust
the moire cancellation level.
1 Press the center of the control button.
1 Press the center of the control button.
The main MENU appears on the screen.
2 Move the control button m/M to highlight
CONVERGENCE and press the control button again.
The CONVERGENCE menu appears on the screen.
3 First move the control button m/M to select the
desired adjustment item. Then move the control
button </, to make the adjustment.
Select
To
horizontally shift red or blue shadows
x Adjusting the moire*
If elliptical or wavy patterns appear on the screen, adjust the moire
cancellation level.
To adjust the amount of moire cancellation, first move
the control button m/M to select
(CANCEL MOIRE).
Then move the control button </, until the moire
effect is at a minimum.
* Moire is a type of natural interference which produces soft, wavy lines
on your screen. It may appear due to interference between the pattern
of the picture on the screen and the phosphor pitch pattern of the
monitor.
Example of moire
4 If necessary, fine tune the color temperature.
SE L ECT
The main MENU appears on the screen.
2 Move the control button m/M to highlight
1 Press the center of the control button.
x Degaussing the screen
The monitor is automatically demagnetized when the power is
turned on.
To manually degauss the monitor, first move the
control button m/M to select
(DEGAUSS). Then move
the control button ,.
The screen is degaussed for about 5 seconds. If a second degauss
cycle is needed, allow a minimum interval of 20 minutes for the
best result.
Additional settings (SCREEN)
The main MENU appears on the screen.
2 Move the control button m/M to highlight
SCREEN and press the center of the control button
again.
The SCREEN menu appears on the screen.
3 Move the control button m/M to select the desired
adjustment item.
Adjust the selected item according to the following
instructions.
US
MENU
Resetting the adjustments
(RESET)
This monitor has the following two reset methods. Use the
RESET menu to reset the adjustments.
1 Press the center of the control button.
The main MENU appears on the screen.
2 Move the control button m/M to highlight 0 RESET
and press the center fo the control button again.
The RESET menu appears on the screen.
Reset the settings according to the following instructions.
Resetting all of the adjustment data for the
current input signal (MODE)
Move the control button <.
The MODE item is selected. All of the adjustment data for the
current input signal is reset.
Note that the following items are not reset by this method.
• on-screen menu language (page 7)
• picture’s rotation (page 10)
Resetting all of the adjustment data to factory
preset levels (ALL)
Move the control button ,.
The ALL item is selected. All of the adjustment data for the
current input signal is reset. All of the adjustment data (except for
the USER settings in the COLOR menu) is reset to the factory
preset levels.
vertically shift red or blue shadows
Note
The monitor’s buttons will not operate for about 5 seconds when ALL is
selected.
10
11
Technical Features
Troubleshooting
Before contacting technical support, refer to this section.
Preset and user modes
When the monitor receives an input signal, it automatically
matches the signal to one of the factory preset modes stored in the
monitor’s memory to provide a high quality picture at the center of
the screen. (See Appendix for a list of the factory preset modes.)
For input signals that do not match one of the factory preset
modes, the digital Multiscan technology of this monitor ensures
that a clear picture appears on the screen for any timing in the
monitor’s frequency range (horizontal: 30 – 86 kHz, vertical: 48 –
120 Hz). If the picture is adjusted, the adjustment data is stored as
a user mode and automatically recalled whenever the same input
signal is received.
Note for Windows users
If thin lines appear on your screen
(damper wires)
The visible lines on your screen especially when the background
screen color is light (usually white), are normal for the Trinitron
monitor. This is not a malfunction. These are shadows from the
damper wires used to stabilize the aperture grille. The aperture
grille is the essential element that makes a Trinitron picture tube
unique by allowing more light to reach the screen, resulting in a
brighter, more detailed picture.
Trouble symptoms and remedies
If the problem is caused by the connected computer or other equipment, please refer to the connected equipment’s instruction manual.
Use the self-diagnosis function (page 15) if the following recommendations do not resolve the problem.
Symptom
If the ! (power) indicator is not lit
• Check that the power cord is properly connected.
• Check that the ! (power) switch is in the “on” position.
If the NO INPUT SIGNAL message
appears on the screen, or if the !
(power) indicator is orange
• Check that the video signal cable is properly connected and all plugs are firmly seated in
their sockets (page 6).
• Check that the HD15 video input connector’s pins are not bent or pushed in.
xProblems caused by the connected computer or other equipment
• The computer is in power saving mode. Try pressing any key on the computer keyboard or
moving the mouse.
• Check that the computer’s power is “on.”
• Check that the graphic board is completely seated in the proper bus slot.
Damper wires
For Windows users, check your video board manual or the utility
program which comes with your graphic board and select the
highest available refresh rate to maximize monitor performance.
If the OUT OF SCAN RANGE
message appears on the screen
xProblems caused by the connected computer or other equipment
• Check that the video frequency range is within that specified for the monitor. If you
replaced an old monitor with this monitor, reconnect the old monitor and adjust the
frequency range to the following.
Horizontal: 30 – 86 kHz
Vertical: 48 – 120 Hz
If no message is displayed and the !
(power) indicator is green or flashing
orange
• Use the Self-diagnosis function (page 15).
Power saving function
This monitor meets the power-saving guidelines set by VESA,
ENERGY STAR, and NUTEK. If no signal is received by the
monitor from the connected computer, the monitor will
automatically reduce power consumption as shown below.
1-5
Power mode
Power
consumption*
! (power)
indicator
normal
operation
≤ 150 W
green
active off**
≤3W
orange
power off
0W
off
On-screen messages
If there is something wrong with the input signal, one of the
following messages appears on the screen. To solve the problem,
see “Trouble symptoms and remedies” on page 13.
OUT OF SCAN RANGE
* Figures reflect power consumption when no USB compatible
peripherals are connected to the monitor.
** When your computer enters the “active off” mode, the input signal is
cut and NO INPUT SIGNAL appears on the screen. After 20 seconds,
the monitor enters the power saving mode.
If using a Macintosh system
Picture flickers, bounces,
oscillates, or is scrambled
INFORMATION
Input signal condition
The input signal condition
OUT OF SCAN RANGE
indicates that the input signal is not supported by the
monitor’s specifications.
NO INPUT SIGNAL
indicates that no signal is being input to the monitor.
Check these items
No picture
US
• Check that the Macintosh adapter (not supplied) and the video signal cable are properly
connected (page 6).
• Isolate and eliminate any potential sources of electric or magnetic fields such as other
monitors, laser printers, electric fans, fluorescent lighting, or televisions.
• Move the monitor away from power lines or place a magnetic shield near the monitor.
• Try plugging the monitor into a different AC outlet, preferably on a different circuit.
• Try turning the monitor 90° to the left or right.
xProblems caused by the connected computer or other equipment
• Check your graphics board manual for the proper monitor setting.
• Confirm that the graphics mode (VESA, etc.) and the frequency of the input signal are
supported by this monitor (Appendix). Even if the frequency is within the proper range,
some video boards may have a sync pulse that is too narrow for the monitor to sync
correctly.
• Adjust the computer’s refresh rate (vertical frequency) to obtain the best possible picture.
Picture is fuzzy
• Adjust the brightness and contrast (page 9).
• Degauss the monitor* (page 11).
• Select CANCEL MOIRE and adjust the moire cancellation effect (page 11).
Picture is ghosting
• Eliminate the use of video cable extensions and/or video switch boxes.
• Check that all plugs are firmly seated in their sockets.
Picture is not centered or sized
properly
• Adjust the size (page 10) or centering (page 10). Note that some video modes do not fill
the screen to the edges.
Edges of the image are curved
• Adjust the geometry (page 10).
Wavy or elliptical pattern (moire)
is visible
• Select CANCEL MOIRE and adjust the moire cancellation effect (page 11).
xProblems caused by the connected computer or other equipment
• Change your desktop pattern.
(continued)
12
13
Symptom
Check these items
Color is not uniform
• Degauss the monitor* (page 11). If you place equipment that generates a magnetic field,
such as a speaker, near the monitor, or if you change the direction the monitor faces, color
may lose uniformity.
White does not look white
Self-diagnosis function
• Adjust the color temperature (page 11).
Letters and lines show red or blue
shadows at the edges
• Adjust the convergence (page 10).
USB peripherals do not function
• Check that the appropriate USB connectors are securely connected (page 7).
• Check that the ! (power) switch is in the “on” position.
Specifications
CRT
Viewable image size
xProblems caused by the connected computer or other equipment
• Check that the power of any self-powered USB compliant peripheral devices is “on.”
• Install the latest version of the device driver on your computer. Contact your device’s
manufacturer for information about the appropriate device driver.
• If your USB compliant keyboard or mouse does not function, connect them directly to
your computer, reboot your computer, and make any necessary adjustments to the USB
settings. Then reconnect the keyboard or mouse to the monitor. If you connect a keyboard
or mouse to the USB connectors and then boot your computer for the first time, the
peripheral devices may not function.
• For customers using Windows 95
1. Right-click on My Computer and select Properties.
2. Click on the Device Manager tab. Scroll down and select Universal Serial Bus
Controller.
If Universal Serial Bus Controller does not appear, you need to load a USB supplement
disk. Contact your computer’s manufacturer for more information about obtaining a
USB supplement disk.
3. Select Generic USB Device from the USB controller list and click on Properties.
4. If there is a check in the box next to “Disable in this hardware profile,” remove the
check.
5. Click on Refresh.
1-6
A hum is heard right after the
power is turned on
This monitor is equipped with a self-diagnosis function. If there is
a problem with your monitor or computer, the screen will go blank
and the ! (power) indicator will either light up green or flash
orange. If the ! (power) indicator is lit in orange, the computer is
in power saving mode. Try pressing any key on the keyboard.
Resolution
Maximum
MENU
! (power) indicator
If the ! (power) indicator is green
1 Disconnect the video input cable or turn off the
connected computer.
2 Press the ! (power) button twice to turn the monitor
off and then on.
3 Move the control button , for 2 seconds before the
monitor enters power saving mode.
Displaying this monitor’s name, serial number,
and date of manufacture
1 Press the center of the control button.
The main MENU appears on the screen.
If the problem persists, call your authorized Sony dealer and give
the following information.
• Model name: HMD-A400
• Serial number
• Name and specifications of your computer and graphics board.
Horizontal: 1600 dots
Vertical: 1200 lines
Recommended Horizontal: 1280 dots
Vertical: 1024 lines
Standard image area
Approx. 352 × 264 mm (w/h)
(13 7/8 × 10 1/2 inches)
Deflection frequency*
Horizontal: 30 to 86 kHz
Vertical: 48 to 120 Hz
AC input voltage/current 100 – 120 V, 50 – 60 Hz, 2.3 A
Power consumption
Max. 150 W
Dimensions
Approx. 497 × 458 × 469 mm
(w/h/d)
(19 5/8 × 18 1/8 × 18 1/2 inches)
Mass
Approx. 26 kg (57 lb 5 oz)
Plug and Play
DDC2B/DDC2Bi
Supplied accessories
See page 6
US
* Recommended horizontal and vertical timing condition
• Horizontal sync width should be more than 1.0 µsec.
• Horizontal blanking width should be more than 3.0 µsec.
• Vertical blanking width should be more than 500 µsec.
• This is the sound of the auto-degauss cycle. When the power is turned on, the monitor is
automatically degaussed for five seconds.
* If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result. A humming noise may be heard, but this is not a
malfunction.
0.24 mm aperture grille pitch (center)
19 inches measured diagonally
90-degree deflection
FD Trinitron
Approx. 365 × 274 mm (w/h)
(14 3/8 × 10 7/8 inches)
18.0" viewing image
MENU
Design and specifications are subject to change without notice.
If all four color bars appear (white, red, green, blue), the monitor
is working properly. Reconnect the video input cable and check
the condition of your computer.
If the color bars do not appear, there is a potential monitor failure.
Inform your authorized Sony dealer of the monitor’s condition.
2 Move the control button m/M to highlight
LANGUAGE/INFORMATION and press the center
of the control button.
The LANGUAGE/INFORMATION menu appears on the
screen.
3 Move the control button m/M to select
.
This monitor’s information menu appears on the screen.
Example
LANGUAGE / I NFORMAT I ON
MODE L : HMD - A 4 0 0
SER I A L : 1 2 3 4 5 6 7 8
MANUF ACTURED : 2 0 0 0 . 5 2
SE L ECT
14
EX I T
If the ! (power) indicator is flashing orange
Press the ! (power) button twice to turn the monitor off
and then on.
If the ! (power) indicator lights up green, the monitor is working
properly.
If the ! (power) indicator is still flashing, there is a potential
monitor failure. Count the number of seconds between orange
flashes of the ! (power) indicator and inform your authorized
Sony dealer of the monitor’s condition. Be sure to note the model
name and serial number of your monitor. Also note the make and
model of your computer and video board.
15
HMD-A400
SECTION 2
DISASSEMBLY
2-1. BUCKET ASSEMBLY REMOVAL
Bucket assembly
2
1
1
Two screws
(+BVTP 4 x 16)
Two screws
(+BVTP 4 x 16)
2-2. A BOARD REMOVAL
CN305
CN309
CN302
CN307
CN306
1
CN303
GND
CN310
CN304
CN301
2-1
A board
HMD-A400
2-3. D BOARD REMOVAL
6
I/O Cable
5
4
3
2
Two screws
(+BVTP 3 X 12)
9
8
Cable stopper
Cable holder
Cable bracket
7
Screw (+BVTP 3 X 12)
Screw
(+BVTT 4 X 8)
A board
CN304
CN301
13
CN302
11
GND
Bottom assembly
Two screws
(+BVTT 4 X 8)
CN310
CN309
CN306
Connector (2P)
P4
CN307
CN305
CN303
1
Anode cap
(Refer to page 2-3)
12
Claw
P2
20
22
D board
Eight screws
(+BV 3 X 12)
19
Side sield (L)
18
17
14
Side sield (R)
Screw
(+BVTT 4 X 8)
16
15
Harnes
Two screws
(+BV 3 X 12)
2-2
21
Two claws
Two screws
(+BV 3 X 12)
HMD-A400
2-4. SERVICE POSITION
A board
D board
• REMOVAL OF ANODE-CAP
NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after
removing the anode.
• REMOVING PROCEDURES
c
b
a
Anode Button
1 Turn up one side of the rubber cap in
the direction indicated by the arrow A.
2 Using a thumb pull up the rubber cap
firmly in the direction indicated by the
arrow B.
• HOW TO HANDLE AN ANODE-CAP
1 Don’t scratch the surface of anode-caps with sharp shaped
material!
2 Don’t press the rubber hardly not to damage inside of anodecaps!
A material fitting called as shatter-hook terminal is built in the
rubber.
3 Don’t turn the foot of rubber over hardly!
The shatter-hook terminal will stick out or damage the rubber.
2-3
3 When one side of the rubber cap is
separated from the anode button, the
anode-cap can be removed by turning
up the rubber cap and pulling up it in the
direction of the arrow C.
HMD-A400
2-5. H BOARD REMOVAL
Three screws
(+BVTP 3 X 12)
1
2
Menu knob
3
H board
Cushion
2-6. PICTURE TUBE REMOVAL
3
4
2
A board
6
Screw
(+BVTP 4 X 16)
Four tapping screws (5)
8
Bottom assembly
3
Deflection yoke
7
Screw
(+BVTP 4 X 16)
Neck assembly
P2
10
P4
Picture tube
Connector (2P)
5
1
Claw
Anode cap
(Refer to page 2-3)
9
2-4
Bezel assembly
HMD-A400
2-7. HARNESS LOCATION
H board
Power switch
P701
P702
P703
Picture tube
P4
P2
CN506
CN901
CN903
CN502
CN505
CN902
CN300
D board
CN501
CN603
CN4001
CN604
FBT
CN602
AC inlet
CN306
CN304
CN301
CN310
CN305
CN302
CN303
CN309
CN307
A board
2-5
HMD-A400
SECTION 3
SAFETY RELATED ADJUSTMENT
8)
When replacing parts shown in the table below, the
following operational checks must be performed as a
safety precaution against X-ray emissions from the unit.
Part Replaced ( ] )
HV Regulator
Circuit
D board
IC502, R515, T501 (FBT)
• Mounted D Board
HV HOLD
DOWN Circuit
D board
D538, IC901, Q534, R521,
R551, R552, R598, R599,
T501 (FBT)
• Mounted D Board
Beam Current
Protector Circuit
D board
IC901, R911, R949, R950,
T501 (FBT)
• Mounted D Board
After adjusting the High Voltage within specification,
put the RV cover on RV501 as shown below and apply
sufficient amount of RTV around RV501.
b) HV Protector Circuit Check
1) Confirm that the voltage between cathode of D517 an
GND is more than 27.5 VDC.
2) Using an external DC Power supply, apply the voltage
shown below between cathode of D517 on "D" and
GND, and confirm that the HV Hold-Down circuit
works. (Raster disappears) Apply DC Voltage: Less than
35.8 VDC.
Check Condition
• Input voltage
• Input signal
• Controls
• B+ Voltage
Allow the unit to warm up for one minute prior to checking
the following conditions:
a) HV Regulator Check
1) Input white cross hatch signal. (fH = 69 kHz)
2) CONT maximum and BRT center
3) Cut off Screen VR (G2).
4) Input voltage: 120 ± 2 VAC
5) Confirm that the voltage is within the voltage range
shown below.
Standard voltage: 26.9 KV ± 0.4 KV
6) When replacing components identified by ], make sure
to recheck the High Voltage.
7) Verify the High Voltage as shown above (26.9 KV ± 0.4
KV) is within specification. If not, set H. SIZE data at
minimum (-127) and then adjust RV501 on "D" Board.
: 120 ± 2 VAC
: (fH = 69 kHz), White Cross Hatch
: CONT (max) & BRT (center)
: 179 ± 3.0 VDC
c) Beam Protector Check (Software logic)
1) Using an external current source, apply < 1.55mA
between pin qa of FBT (T501) and GND, and confirm
that the raster fades out.
Check Condition
• Input voltage
• Input signal
• Controls
: 120 ± 2 VAC
: (fH = 69 kHz), White Cross Hatch
: CONT (max) & BRT (center)
d) B+ Voltage Check
1) Input white cross hatch (fH = 69 kHz) signal.
2) CONT (max) & BRT (center)
3) Input voltage: 120 ± 2 VAC
Note: Use NF power supply or make sure that distortion
factor is 3% or less.
4) Confirm that the voltage is within the voltage range
shown below.
Standard voltage: 179 ± 3.0 VDC
RV501
3-1
HMD-A400
SECTION 4
ADJUSTMENTS
Connect the communication cable of the computer to the connector located on the monitor. Run the service software and then follow
the instruction.
I2C Interface Card
I2 C Interface Cable
HD15 Connector Adapter
Computer
as a Jig
Video Cable
• Landing Fine Adjustment
1.
2.
3.
4.
Put the set inside the Helmholtz coil.
Set TLH plate to zero position.
Input the single green signal.
Demagnetize the CRT surface with the hand degausser , and
perform auto degaussing.
5. Attach the wobbling coil to the designated part of the CRT
neck.
6. Attach the sensor of the landing adjustment unit on the CRT
surface.
Purity magnet position
L/D control specification
±5
±5
±5
a
d
±5
±5
±5
(µm)
10. If the corner landing is out of specification, put a disk magnet for the landing correction.
11. Perform auto degauss in case disk magnets are used.
12. Remove the sensor and wobbling coil.
13. Fix purity magnet on DY with UL black tape.
7. Adjust the DY position and purity, and the DY tilt.
8. Fasten DY with screw.
Note: Torque 20 +2
-1 kgcm
9. Adjust top and bottom pins by pitching DY up and down
with two wedges.
Also leave the yaw of DY to physical center position with
Another two wedes.
c
±7
±7
±7
“a” and “b” must be equal, and
“c” and “d” must be equal.
b
<How to drive in wedges>
4-1
HMD-A400
• Convergence Specification
• Convergence Rough Adjustment
1. Enter the crosshatch signal.
2. Recheck focus and readjust when focus was worse.
3. Adjust roughly H. STAT and V. STAT convergence by 4
pole magnet.
4. Adjust roughly HMC and VMC by 6 pole magnet.
B
• Convergence Adjustment
1. Open H and V Stat by 4 pole magnet.
2. Adjust 6 pole magnet perform HMC and VMC.
3. Adjust 4 pole magnet close both Stat of R.G.B just overlap
each other Horizontal and Vertical.
4. Adjust TLH for side MC by TLH magnet when R or B is in
the opposite direction.
5. Adjust XCV to correct Vertical cross MC.
6. Adjust XBV to correct Vertical bow MC.
7. Adjust TLV to corect Vertical tilt MC.
8. Adjust YCH to correct top and bottom Horizontal cross MC.
9. Adjust YBH to correct top and bottom Horizontal bow MC.
10. Using permalloys to correct MC of the cornters.
11. Check convergence for whole screen. If necessary, perform
step from 3-9 and correct with permalloys.
12. Paint lock 4 pole magnet, 6 poles magnets, XBV reactor
XCV corrector and TLH corrector handle.
0.30 mm
B
0.35 mm
• Vertical and Horizontal Position and Size
Specification
A
b
MODE
a
6Pole Mg
All mode
A
• White Balance Adjustment Specification
(1) 9300K
(2) 6500K
x = 0.283 ± 0.01
x = 0.313 ± 0.01
y = 0.298 ± 0.01
y = 0.329 ± 0.01
(2) 5000K
x = 0.346 ± 0.01
y = 0.359 ± 0.01
B
Purity Mg.
MODE
A
TLH
All mode
A
312 mm
B
234 mm
XCV
a
b
YV
YCH
CRT
DY
1.5 mm
1.5 mm
• Focus adjustment
Adjust the focus volume 1 and 2 for the optimum focus.
4Pole Mg
XCV
XBV
YCH
B
R
TLV
R
B
YBH
TLH
R
B
B
R
Focus 1
(V)
Focus 2
(H)
B
R
R
B
B
R
R
B
FBT
4-2
HMD-A400
MEMO
4-3
SECTION 5
DIAGRAMS
5-1. BLOCK DIAGRAMS
SIGNAL-IN
HD15
PIG-TAIL
5
A
15
(VIDEO, RGB OUT)
IC001 PRE AMP,OSD MIX
10
14
9
3
13
8
2
12
5
7
9
1
2
IC002
RGB OUT
2 R IN
6 G IN
R OUT 35
9 R VIN2
R VOUT2 3
11 B IN
G OUT 32
8 G VIN3
G VOUT3 5
B OUT 29
11 B VIN1
B VOUT1 1
R.G.B
CRT
G1
G2
4
CN301
RED
GREEN
BLUE
H-IN
V-IN
7
D305
1
IC009
ROM
11
6
CN306
PC DET
DDC SDA
DDC SCL
DA4 23
7 VCLK
5 SDA
6 SCL
4
3
2
D205
D105
TO D BOARD
CN902
A
6
5
4
3
1
TO D BOARD
CN901
B
CN302
CLAMP
SDA/I
SCL/I
H_RTN
V_RTN
G1
TO D BOARD
CN603
C
TO
D BOARD
FBT
FV1
TO
D BOARD
FBT
CN309
1.2kV
2
1
4
3
CN304
CS0
CS1
CS2
CS3
E
TO D BOARD
CN504
F
TO D BOARD
CN502
6
19 CLAMP
–
+
DA1 26
7
G2 CONT
Q004
5
7
8
9
3
4
5
5
6
4
3
1
1
IC004 AMP
21 SDA
20 SCL
IC003 OSD
27 BLK
CN303
ABL
+5V
+6.3V
+12V
+81V
R CUT-OFF
Q101
DA2 25
CLAMP AMP
Q001,002
FV2
G CUT-OFF
Q201
DA3 24
CN305
DDC SCL
DDC SDA
PCDET
V-IN
H-IN
TO
D BOARD
FBT
HV
B CUT-OFF
Q301
15 ABL IN
OSDR 4
13 P1/R
OSDG 9
15 P3/G
OSDB 13
17 P5/B
OSD BLKIN 1
12 P0/BK0
+5V
+6.3V
+12V
+81V
6 SIN
5 SCK
H SYNC
BUFF
Q003
V SYNC
BUFF
Q005
18 HOR
19 VERT
P2 14
P4 16
P6 9
P7 10
B-SS3578<U/C>-BD1-EPS05
H
(USER CONTROL)
SW701
MENU
TO D BOARD
CN903
D
P701
MENU
ORANGE/LED
GREEN/LED
1
2
3
LED701
POWER
5-1
5-2
USB BLOCK
D
µ-COM, DEFLECTION CONTROL,
DEFLECTION, HV, POWER SUPPLY,
H.DF, V.DF, USB CONTROL
CN2903
USB DB_A BLOCK
IC7000
USB CONT
IC7001
1
ENA
PSW1 32
7
2
FLGA
8
3
FLGB
OC1_N
OC2_N
PSW2
4
2
ENB
1
OUTA
8
OUTB
5
P8D1
V1
M1
P1
V2
M2
P2
2
6
5
1
4
3
2
P7D1
V1
M1
P1
2
6
5
V2
M2
P2
1
4
3
3
CN2903
1
2
DM1 26
DP1 27
SCL
SDA
1
2
SCL
SDA
P7000
USB DM
USB DP
CN904
USB DM
USB DP
23 INDV/SCL
22 OPTION/SDA
DM2 30
DP2 31
28 DM0
29 DP0
DP3 5
DM4 12
DP4 13
DM3
1
2
20 XTAL2
X7000
6MHz
IC 501
DEFLECTION
CONTROL
19 XTAL1
3
4
CN2903
USB DB_B BLOCK
1
PSW3 16
1
OC3_N 9
OC4_N 10
PSW4 17
2
FLGA
3
FLGB
4
ENA
ENB
OUTA
8
OUTB
5
IC7002
2
5
2
1
P8D2
V3
M3
P3
P7D2
V3
M3
P3
5
2
1
4
6
7
V4
M4
P4
V4
M4
P4
4
6
7
3
CN2903
1
2
3
USBVCC 14
+5V
USBDM 15
IC901 CPU
IC903
RESET
USBDP 16
T502
OUT 3
1 IN
40 Reset
HDRV
BUFF
Q526
PA6 34
TO A BOARD
CN305
A
CN902
H-IN
V-IN
PCDET
SDA
SCL
H SYNC BUFF
Q902
18 HSYNCI
1
3
4
5
6
19
26
28
27
16 CLBL
PD0/V SYNCO 20
14 VSYNC
PD1/H SYNCO 21
15 HSYNC
PD4/ITB 24
PB0/SCLD
H DRIVE
Q523,527
IC401
V OUT
VSYNCI
PD6/CLAMPOUT
PB1/SDAD
H DRIVE
OUT
Q502
H DRIVE
Q520,521
8
VOUT1 13
7 +V IN
VOUT2 12
1 -V IN FLYBACK 3
5
6
1
9
H OUT
Q503
L505
OUT 5
1
2
3
CN501
H DY(+)
H DY(+)
H DY(–)
4
5
6
H DY(–)
V DY(–)
V DY(+)
V.DY
RY501
17 HUNLOCK
H.DY
T503
D511
HFLB 1
18 SCL
ABL/O
TO A BOARD
CN302
B
25 PD5/HFBACK
3
V_RTN
SOG
SDA/I
SCL/I
H_RTN
G1
6
9
2
1
7
5
S CAP CHANGE
Q505, Q506-Q509,
Q524, Q536, Q537
H CENT
DRIVE
Q517,518
8
BIN 5
OSCOUT 32
X901
24MHz
CN901
CLAMP
10
2
19 SDA
11 PB5/AIN1
H_RETURN
5
EWDRV 11
B DRIVE
Q515,516
BDRV 6
SWITCHING
Q501
1
D512
PD3/ITA/VFBACK 23
5
7
DF AMP
Q504, Q530
1 PC0/HSYNCDIV
30 PB3/SDAI
1
2
CN505
ROTATION+
ROTATION-
5
1
3
4
6
CN603
ABL
+81V
+12V
HERTER
+5V
E
TO A BOARD
CN309
PC7/PWM7 8
29 PB2/SCU
PC3/PWM3 4
SW
Q511
T504
DF AMP
Q514, Q543, Q544,
Q547-Q549
FOCUS 32
PS5/PWM5 6
IC902
EEP ROM
T501
FBT
11
1
HV
9
12
11
D521
D517
SYNC BUFF
Q538, 539
BOP CONT
Q510, Q513
BOP CONT
Q512
42 PA0/OCMP
39 PA1/RDI
2
3
1
HV
TO CRT ANODE CAP
H CENT
Q519
IC502
PWM CONT
D
CN504
1.2kV
TO A BOARD
CN304
RELAY DRIVE
Q540
BOP 3
+12V
TO H BOARD
P701
1
F
22 PD2/C SYNCI
TEST 7
SDA 5
SCL 6
CN903
ORANGE/LED
GREEN/LED
MENU
CN502
CS1
CS2
CS3
CS0
6
OSCIN 33
C SYNC BUFF
Q901
4
1
2
3
4
OSC
8
V REF
1
COMP
2
FB
OUT
6
Q522
10
14
8
FV1
FV1 TO CRT
FV2
FV2 TO CRT
7
13
D509
6
VR501
HV
ADJ
12 PB4/AIN0
Q5201, Q5202
3
I SENSE
3
15
PA7/BLANKOUT 31
Q532, Q535
PC4/PWM4 5
+12V
4
IC504 (1/2)
AMP
3
1
+
Q531
OVP
Q525, 534
TILT DRIVE
Q541, Q542
–
PB7/AIN3/PWM1 9
TILT(ROTATION)
COIL
2
37 PA3
38 PA2/TD0
7 PS6/PWM6
PB6/AIN2/PWM0 10
PA5 35
SW
Q401
ABL CONT
Q528, 529
D601
AC RECT
SW601
POWER
CN601
F601
ABL CONT
Q533
T603 PIT
LF601
LFT
T601
D613
L606
D628
+200V
11
AC-SOCKET
D612
TH601
10
3
D631
D615
+81V
IC607
+12V REG
12
D623
D627
D626
D616
D604
DGC
DGC
NC
DGC
1 IN
13
9
1
CN602
1
2
3
TH602
IC601
PWM CONTROL
RELAY DRIVE
Q615
OUT 3
+12V
+15V
+6.3V SW
CONT
Q608
D617
RY601
+5V
+12V
IC504 (2/2)
AMP
3
-12V
16
+
–
CN506
1
1
2
2
4
OSC
8
V AEF
Vcc
7
1
COMP
OUT
6
+6.3V SW
Q607
+15V
IC4002
AMP
D610
IC606
SWITCHING
Q602
D6005
A
G
K
5
SW
Q601
3
IC4000
T6000
+5V
6
2 SCL
AO2 13
FB603
2
FB
3
CN4001
1
V.CONV DRIVE
Q4003, Q4004
1
2
3
4
2
4
I SENSE
D609
+
–
D620
IC602
VOLTAGE
FEED BACK
3 SDA
AO3 14
AO4 15
IC603
VOLTAGE
FEED BACK
IC6000
2
R
K
A
IC4001
AMP
3
PH6000
+
–
IC6001
1
H.CONV DRIVE
Q4001, Q4002
2
K
G
A
PH6001
D6000
Q6000
B-SS3578<U/C>-BD2-EPS05
5-3
5-4
C
TO A BOARD
CN303
5-2. FRAME SCHEMATIC DIAGRAM
5-3. CIRCUIT BOARDS LOCATION
CN301
6P
H-IN
V-IN
GND
RGND
RED
GGND
GREEN
BGND
BLUE
A
VIDEO,
RGB OUT
A
1
2
3
4
5
6
7
8
9
VIDEO CABLE
1
2
3
4
VIDEO CABLE
CN301
6P
+5V
DDC SCL
DDC SDA
PCDET
HG
H
PICTURE
TUBE
CN902
7P
1
2
3
4
5
6
H-IN
GND
V-IN
PCDET
SDA
SCL
CN309
1P
1.2kV
1
1
2
3
4
CS1
CS0
CS3
CS2
CN304
4P
SOG
GND
H_RTN
V_RTN
G1
GND
CLAMP
SDA/I
SCL/I
CN302
9P
1
2
3
4
5
6
7
8
9
GND
+5V
ABL
+6.3V
+12V
GND
+81V
7
6
5
4
3
2
1
CN303
7P
RGB G1 G2
H
1
2
3
4
5
6
7
H
H-IN
GND
V-IN
PCDET
SDA
SCL
PC+5V(NC)
CN902
7P
1
1.2kV
CN504
1P
4
3
2
1
CS1
CS0
CS3
CS2
CN502
4P
CN901
10P
Auto-Size(NC) 10
9
SOG
8
GND
7
H_RTN
6
V_RTN
5
G1
4
GND
3
CLAMP
2
SDA/I
1
SCL/I
CN603
7P
P701
7P
MENU
ORG LED
GRN LED
GND
GND
+5V
ABL
+6.3V
+12V
GND
+81V
7
6
5
4
3
2
1
D
HV
CN903
4P
1
2
3
4
1
2
3
4
MENU
ORANGE/LED
GREEN/LED
GND
USER
CONTROL
CN506
2P
2
1
CN4001
6P
D
CN602
3P
DGC
µ-COM,DEFLECTION CONTROL,
DEFLECTION,HV,POWER SUPLLY,
H.DF, V.DF, USB CONTROL
DGC
NC
DGC
1
2
3
1
2
3
4
CN601
AC-SOCKET
CN501
6P
H
H
H
H
V
V
DY+
DY+
DYDYDYDY+
1
2
3
4
5
6
H DY
V DY
L
G
N
CN505
2P
ROTATIONROTATION+
2
1
TILT(ROTATION)
COIL
B-SS3545<AEP>-KESSENZU-EPS05
5-5
5-6
5-4. SCHEMATIC DIAGRAMS AND PRINTED
WIRING BOARDS
Note:
• All capacitors are in µF unless otherwise noted. (pF: µµF)
Capacitors without voltage indication are all 50 V.
• Indication of resistance, which does not have one for rating
electrical power, is as follows.
(1) Schematic Diagram of H Board
• Divided circuit diagram
One sheet of D board circuit diagram is divided into six
sheets, each having the code D-a to D-f. For example, the
destination ab1 on the D- a sheet is connected to ab1 on the
D-b sheet.
a
b
1
2
3
4
5
6
7
A
1
Ref. No.
Pitch: 5 mm
Rating electrical power 1/4 W (CHIP : 1/10 W)
Circuit diagram division code
• All resistors are in ohms.
• f : nonflammable resistor.
• F : fusible resistor.
f : internal component.
•
• p : panel designation, and adjustment for repair.
• All variable and adjustable resistors have characteristic curve B,
unless otherwise noted.
e : earth-ground.
•
E : earth-chassis.
•
• All voltages are in V.
• Readings are taken with a 10 M digital multimeter.
• Readings are taken with a color-bar signal input.
• Voltage variations may be noted due to normal production
tolerances.
•
* : Can not be measured.
• Circled numbers are waveform references.
• s : B + bus.
• S : B – bus.
• When replacing components identified by ] , make the
necessary adjustments indicated. (See page 3-1)
• When replacing the part in below table, be sure to perform the
related adjustment.
Note: The components identified by shading and mark
0 are critical for safety. Replace only with part
number specified.
Note: Les composants identifiés par un tramé et une
marque 0 sont critiques pour la sécurité. Ne les
remplacer que par une pièce portant le numéro
spécifié.
B
LED701
LT6463-23-D51
(POWER)
P701
4P
MENU
ORANGE/LED
GREEN/LED
GND
R701
2.15k
1%
R706
3.83k
1
2
3
4
D board IC502, R515,
T501 (FBT)
• Mounted D board
HV Hold-down
Circuit Check
D board D538, IC901, Q534,
R521, R551, R552,
R598, R599,
T501 (FBT)
• Mounted D board
Beam Current
Protector Circuit
Check
D board IC901, R911, R949,
R950, T501 (FBT)
• Mounted D board
R705
6.19k
R702
15k
1%
SW701
4
MENU
3
2
5
TO D-a BOARD
CN901
6
C
1
D
H (USER CONTROL)
B-SS3578<U/C>-H..-EPS05
Part Replaced (])
HV Regulator
Circuit Check
R709
10.2k
1%
(h)
USER CONTROL
— H BOARD —
Schematic diagram
5-7
H
Board
l
5-8
(2) Schematic Diagram of A Board
7
CN305
6P
1
2
3
4
5
6
33
32
GIN
GOUT
C110
100p
EXTFB
SOGI
MBRI
VCCG
BOUT
OSDG
EXTFB
VCCB
OSDB
GNDB
ABLIN
NC
SDA
VCC
SCL
SOG OUT
29
28
27
25
7
G VIN3
GND
VCC
G VOUT3
GND2
R VOUT2
GND1
B VOUT1
5
4
3
2
1
53.1
2.9 2.0
C009
47
16V
R310
3.3k
R042
100
1/2W
FB215
FB115
R215
110
1/2W
C010
0.1
50V
R115
68
1/2W
D017
ER106
C045
10000P
3kV
C019
0.1
100V
HV
TO
D BOARD FBT
5
6
R034
10k
1/2W
SG001
R035
2.2M
1/2W
CN309
1P
1
C014
0.01 2kV
C303
0.1
50V
R005
1k
R303
1k
C310
100p
0.6
C106
0.1
100V
L102
0.1µH
2.1
DA2
DA3
DA4
GND5
1.5
D103
HSS82
C008
0.1
50V
R108
20k
SG101
D104
HSS82
SG301
+80VF
R112
120
1/2W
R111
1M
2.9
R107
5.1k
R208
20k
+5V
C004
0.22
16V
C025
0.1
50V
D
C107
0.1
D105
HSS82
2.9
C304
0.1
50V
C204
0.1
50V
Q101
2SC1921
R CUT-OFF
C104
0.1
50V
5.0
R109
510
R308
20k
5.0
1
2
3
4
5
6
7
8
9
C206
0.1
100V
L202
0.1µH
D203
HSS82
D204
HSS82
+80VF
R212
120
1/2W
R211
1M
+5V
R207
5.1k
R014
4.7k
R013
4.7k
R018
100
D303
HSS82
P5/B
17
SCK
P4
5.0
R309
510
VDD1
P2
FB002
2µH
L002
FB005 150µH
R302
+81VF
+12V
+12V
+6.3V
R113
470
D001
1SS119
13
C036
0.1
R025
2.2k
P0/BK0
P7
VSS
C038
47
16V
R030
10k
11
P6
Q004
2SC4634
G2 CONT
+IN.B
-IN.B +IN.A
OUT.B -IN.A
Vcc
OUT,A
Vee
R031
22M
C028
330p
R033
220k
C016
1000p
12
0
9
C045
0.1
P1/R
10
CN303
7P
C015
0.47
16V
14
7
TCK
0
C035
100
10V
R023
300k
15
6
P3/G
+12V
IC004
LM358
AMP
R024
150k
+12V
8
G
SIN
+12V
R213
470
0
5.0
Q003
2N3904
H SYNC BUFF
Q301
2SC1921
B CUT-OFF
R313
470
4
CS
3.8
3
HOR
2
VERT
AC
5.0
5.0
R028
1k
D305
HSS82
1
VIR
16
19
2
0
C307
0.1
C030
470
16V
0
C027
330p
R307
5.1k
5.0
3
C032
1 50V
C040
0.01
100V
20
1
VDD2
4
R026
470
4.4
CPOUT
FB012
C033
4700p 50V
R312
120
1/2W
R311
1M
1.3
5
C034 R039
0.1 2.4k
50V
C026
5600p
50V
1
2
3
4
5
6
7
D304
HSS82
+80VF
IC003
M35047
OSD
5.0
+5V
D003
MTZJ5.1B
C306
0.1
100V
L302
0.1µH
JW035
150µH
6
R022
2.4k
Q005
2SC945
V SYNC 0
BUFF
F
C042
12p
50V
R020
1k
R021
12.4k
R015
240
1/4W
+5VF
D004
1SS119
7
+5V
R209
510
18
C055
33p
D205
HSS82
8
C056
33p
C207
0.1
Q201
2SC1921
G CUT-OFF
R019
100
TO D-a BOARD
CN901
+81VS
GND
+12V
+6.3V
ABL
+5V
GND
0.2
C023
100
10V
5
SOG
GND
H_RTN
V_RTN
G1
GND
CLAMP
SDA/I
SCL/I
CLAMP
19
0.6
CN302
9P
R032
56K
C039
100
16V
C037
0.22
16V
R029
1.5k
C029
1000p
50V
CN304
4P
C047
0.1
R037 100
R036 100
FB004 150µH
C017
0.1
100V
TO D-d BOARD
CN603
C020
47
16V
+5V
R001 100
R002 100
C049
0.1
100V
FB011
1
2
3
4
CS1
CS0
CS3
CS2
TO D-b BOARD
CN502
B-SS3578<U/C>-A..-EPS05
I
1.2kV
TO D-b BOARD
CN504
L301
0.1µH
4.4
C108
0.1
R315
68
1/2W
C011 C012 C048
10 0.1 0.1
100V 100V 100V
R304
22
RGB G1 G2
4
FB315
+80VF
R203
1k
C210
100p
C043
4.7
35V
N.P
4.7
C013
0.1
50V
52.7
41.9
FB001
JW
V901
PICTURE
TUBE
HG
H
FB003
2µH
0.1
R016
470
FB008
C105
0.1
2.1
13
SG201
DA1
24
Q001
2N3904
CLAMP AMP
D002
1N4148
C120
0.1
BIN
23
Q002
2N3904
CLAMP AMP
-0.2
R008
2.4k
6
1.1
0.8
22
/TEST
R006
10k
+5V +12V
R007
100
1
VCC
D013
1N4148
1
2
3
4
1.1
C022
390p
50V
7
3
2.6
D009
1SS119
8
D011
1SS119
NC
2
C109
220p
VCLK
R010
100
BLK
GNDG
21
R102
4.7k
11
/WP
3
SCL
0.2
8
R210
3.3k
4.4
0.1
C203
0.1
50V
R009
1k
6
TO D-a BOARD
CN902
R120
47
R106
47
R046
3k
10
VSS
4
SDA
26
R011
470
C041
FB010 220p
9
R204 L201
68 0.1µH
2.9
2
2.9
31
R101
75
GNDR
10
2.1
FB006
3µH
R103
1k
+12V
+5V
IC005
24C21
DDC
L101
0.1µH
35
34
GNDA
20
D008
1SS119
R105
47
CN306
4P
H
36
1
2
3
OSDR
+12V
D010
1SS119
FB009
+5V
DDSCL
DDSDA
PCDET
C103
0.1
50V
D012
1SS119
5
H-IN
GND
V-IN
PCDET
DDSDA
DDSCL
R201
75
EXTFB
30
R301
75
+5V
R104
22
0.1
6
SIGNAL IN
HD15
PIG-TAIL
VCCR
4
C302
10 50V
C002
220
16V
12
+6.3V
+12VF
R110
3.3k
5
FB301
JW
C006
0.1
50V
2.0
ROUT
6
11
VCC2
1
7
7
1
RIN
8
12
OSD BLKIN
+12V
C202
10 50V
C005
470
16V
R004
100
2.6
11
IC002
LM2412
RGB OUT
IC001
M52743BSP
PRE AMP,OSD MIX
C102
10 50V
FB201
JW
11
J001
CRT_SOKET
L001
100µH
0.1
12
2
D301
1SS119
13
8
FB101
JW
D201
1SS119
D302
1SS119
14
13
D202
1SS119
15
14
9
3
1
2
3
4
5
6
7
8
9
10
9
+12VF
C054
0.1
16
4
H-IN
V-IN
GND
RGND
RED
GGND
GREEN
BGND
BLUE
D101
1N4148
17
15
10
D102
1N4148
18
5
E
8
9
A
(VIDEO,RGB OUT)
CN301
9P
C
6
R VIN2
5
+12V
A
B
4
VBB
3
2
B VIN1
1
• A BOARD WAVEFORMS
2
1
H
0.75 Vp-p (H)
4
3
5
6
H
1.08 Vp-p (H)
5-9
0.75 Vp-p (H)
43.5 Vp-p (H)
43.5 Vp-p (H)
44.5 Vp-p (H)
5-10
14
(a)
VIDEO, RGB OUT
— A BOARD (Coductor Side) —
— A BOARD (Component Side) —
Schematic diagram
Ò A
board
5-11
5-12
(d)
µ-COM, DEFLECTION CONTROL, DEFLECTION,
HV, POWER SUPPLY, H DF, V DF, USB CONTROL
— D BOARD —
5-13
5-14
(3) Schematic Diagrams of D (a
a , b , c , d , e , f ) Board
1
3
2
4
5
6
7
8
10
9
11
12
14
13
D-a
A
(µ-COM,DEFLECTION CONTROL)
ad2
ad1
PC0/
HSYNCDIV
PA0/OCMP
PC1/VA
TEST/Vpp
4
PA1/RDI
R904 100
6
PA3
7
PS6/PWM6
PA4
8
PC7/PWM7
R955
10k
C409
1000p
100V
35
33
CN505 2P
TILT(ROTATION)
COIL
-12V
Q526
RN1203
BUFF
29
D904
HZ5C1
C505
0.1
R504
732 1.0
1%
C506
0.01 2.6
100V
C918
47p
C507
4700p
100V
+5V
CN901
10P
H
16
17
15
14
13
12
21
R571
4.7k
GNDS
HPLL1
PGND
HBUF
BDRV
HDRV
R508
13k
R522
4.7k
R513
100
5.7
HDRV
R500
43
5.3
HREF
BIN
HCAP
BSENS
HPLL2
1.5
BOP
HSMOD
XRAY
FOCUS
HFLB
R507
10k
BOP
2.5
31
4.6
BDRV
R592
47k
2.5
4.5
5.4
R924
1k
1
SCL/I
2
SDA/I
3
CLAMP
4
GND
5
G1
6
V_RTN
7
H_RTN
8
GND
9
SOG
Auto-Size(NC) 10
DGND
2.4
R505
2.8k
1%
C919
47p
VCC
VCAP
L509
150µH
10
R503 4.7k
R933
22
D903
HZ5C1
VREF
7
R932
22
R947 47
C927
100p
18
19
20
4.9
R952 47
C926
100p
22
2
4
C503
0.1
100V
C504 0.01 100V
C513
220p
50V
+12V
2.8
C510 C534
1000 0.1
16V 50V
2.7
R928 R929 R930
10k 10k 10k
R931
10k
EWDRV
6
+5V
VOUT2
9
3.1
5.0
Audio_Mute
VAGC
10
Vss
VSOMD
C512
220p
50V
2.9
9
A2
SDA
VOUT1
3.2
3
SCL
COR
23
R944
470
D902
MTZJ5.1A
TO A BOARD
CN305
PMG0
SDA
C502
0.1
100V
R502
22.1k 1%
6
C914
100p
0
2.9
32
C531
0.022
100V
6.1
0.2
R922
10k
6.3
Q901
H2N3904
C SYNC BUFF
C509
3300p
100V
1
G
1
2
3
4
5
6
7
A1
5
R920
10k
CN902
7P
H-IN
GND
V-IN
PCDET
SDA
SCL
PC+5V(NC)
A0
TEST
VSYNC
24
0.5
0.5
R919
4.7k
F
Vcc
SDA
8
4.9
R918
10k
D901
HZ5C1
R510 R511
100 100
0.4
HSYNC
6
7
IC902
24LC16
EEPROM
D905
HZ5C1
+5V
C915
100p
C920
0.1
H_RETURN
D906
HZ5C1
Q902
H2N3904
H SYNC BUFF
SCL
4.6
SCL
4.9
25
PD2/
CSYNCI
PD1/
HSYNCO
0.8
HUNLOCK CLBL
5.0
R934
47
22
21
HSYNC/O
+5V
R925
10k
23
-0.6
0.4
TO H BOARD
P701
0.2
26
PD3/ITA/
VFBACK
0
VSYNC/O
R412
6.8k
1%
BLANK OUT
R951
4.7k
R926
100
27
PD0/
VSYNCO
0.2
28
PD4/ITB
PD5/HFBACK
4
29
VSYNCI
R411
6.8k
1%
30
HSYNCI
4.2
D907
1N4148
+5V
1
R943
1k
ae1
R913
1k
1.7
8
C930
220p
MENU
ORANGE/LED
GREEN/LED
3
18
1
2
3
4
PD6/CLAMPOUT
19
CN903
4P
VSS
0.5
0.1
R946
100
26
5.0
7
R921
1k
D908
1SS119
27
C907
10
25
C910
0.1
24
C911
0.1
R529
1k
0.8
R935
10k
4.1
C913
22p
17
TO D-f BOARD
P7000
C912
22p
+5V
28
15
PB0/SCLD
FB903 0.45µH
+5V
MENU
ORANGE/LED
GREEN/LED
GND
PB1/SDAD
USBDP
ROTATION+
ROTATION-
C581
0.22 50V
R5125
430
R5120
46.4k
0.7-4.0
USBDM
16
1
2
3
20
USB DM
USB DP
GND
E
PB2/SCU
VSYNC/O
-12V
11
USBVCC
R406
1.5
1
2
C579
3300p
100V
4.9
FB902 0.45µH
R404
0.75
2W
C402
470
25V
5.0
CN904
3P
C405
0.22
50V
8
PB3/SDAI
R407
330
1W
C572
47
16V
0.1
FB901 2µH
C908
0.1
C403
0.022
100V
Q542
2SB647
TILT DRIVE
R5123
10k
4.9
D911
1N4148
R401
2.15k
5
VDD
C571
0.1
50V
32
PB4/AIN0
C922
22p 50V
C921
22p 50V
0.1
4
C909
470p
PA7/
BLANKOUT
C925
0.1
R912 10k
C924
4.7
OSCOUT
R937 0
31
R950
16k
PB5/AIN1
12
11
R911 1k
ABL/O
X901
24MHz
R936
1M
2.3
5
-2.0
0.3
2.2
ab3
3
4
3
OSCIN
5
ab2
6
C580
0.1
100V
1
4
34
9
PB6/AIN2/
PWM0
C928
0.1
R949
10k
MENU
PA6
-14.3
R5124
100
8
3
0.1
PB7/AIN3/
PWM1
3.1
R909 1k
ac1
4.9
PA5
10
1N4148
R908 10k
36
2
D910 +5V
C404
1000
25V
2
2.5
R906 1k
C906
2.2
R403
1/2W
2
IC401
TDA8172
V OUT
-1.4
IC504(1/2)
LM358
0.3
AMP
2
30
R914
33.2
1
HSYNC/O
TILT
R5122
47k
4.9
R905 1k
R915
30.1k
D
PS5/PWM5
Q541
2SD667
TILT DRIVE
R954
4.7k
0
13
R948
1.4k
PA2/TDO
7 +
0.7
1 -
-2.0
C905 2.2
H-DRIVER
PC4/PWM4
14
C
39
1
0.7
C563
330
16V
R953
10k
38
C904 2.2
R941
47
C570
10
50V
R5121
10K
2
C923
2.2
37
R903 1k
+12V
GND
5
C903 2.2
D402
1N4002
C408
470
35V
3 OUT IN 1
2.0
R902 1k
C406
3300p
100V
5.0
40
3
Reset
PC3/PWM3
R402
2.1k
1%
IC903
M51951B
RESET
R940
10k
5.0
PC2/PWM2
1.2
C902 2.2
TEST
BLK
CS4
R942
47
15.2
2
R907
1k
42
1
C900
0.1
+15V
+5V
41
TH602
10k
IC901
ST72754
CPU
GREEN/LED
0.7 ORANGE/LED
R900
2.7k
4.9
B
TILT
TEST
H-CENTER/O
BRI
ABL/PWM
ab1
+5V
0.2
IC501
TDA4841
DEFLECTION
CONTROL
R596
95.3k
R501
27k
HFLB
R506
10k
R923
10k
C508
100p
50V
D501
1SS119
TO A BOARD
CN302
FOCUS
MUTE
HUNLOCK
G1/VBLK
ab4
B-SS3578<U/C>-D..-P1-EPS05
I
• Divided circuit diagram
One sheet of D board circuit diagram is divided into six
sheets, each having the code D-a to D-f. For example, the
destination ab1 on the D-a sheet is connected to ab1 on the
• D - a BOARD WAVEFORMS
2
1
a
b
4
3
D-b sheet.
5
6
7
8
0
9
1
Ref. No.
3.2 Vp-p (H)
3.4 Vp-p (H)
5.0 Vp-p (H)
4.0 Vp-p (V)
2.8 Vp-p (24MHz)
5.0 Vp-p (H)
5.0 Vp-p (V)
Circuit diagram division code
Schematic diagram
5-15
D
-a board
l
5-16
3.0 Vp-p (V)
2.0 Vp-p (V)
12.0 Vp-p (H)
1
3
2
4
5
6
7
8
10
9
11
12
13
D-b
A
(DEFLECTION)
Q532
16.4 2SA733
R509
3.6k
ab3
R409
3k
D523
1SS119
V DY-
1.9
-27.6
Q529
2SC945P
ABL CONT
Q528
2SC945P
ABL CONT
C574
330
R585
5.1k
Q401
2SC945
SW
C577
22
250V
R5102
13k
R5103
10k
R5107
10k
R5109
1M
R5113
51k
R5112
6.8k
16.4
R5108
18k
R5110
470
Q535
RN1203
R5106
470
Q533
2SA733
D592
1SS119
0.5
C514
0.1
bc3
D532
Z10-160B
R590
1M
R5111
20k
1.4
D527
HZ12A1
C575
0.01
C401
0.1
250V
Q531
KSP92
R523
10k
D522
PG104R
R589
10k
R586
124k
15.8
R512
1k
V DY+
ab2
+12V
H-CENTER/O
D540
1N4148
16.4
R408
3.3k
1/2W
ABL/PWM
+12V
R516
4.3k
B
BRI
BLK
H-DRIVER
ab1
L502
100µH
bd1
C591
0.1
C590
0.1
C576
0.1
bc1
bc4
G1/VBLK
C
+12V
bc5
R576
51k
2W
R5201
1.1k
D5201
1N4148
C595
0.1
400V
+12V
Q5201
RN1203
R5202
3k
Q5202
2SC945
Q530
2SC2688
DF AMP
T504
74.8
L508
0.12
1/2W
+12V
R5129
1k
Q504
2SC945
DF AMP
R573
36k
D520
1N4148
C5201
10
10V
7
C568
22p
2kV
11
R572
10
0.4
D
5
R577
120
C592
4.7
35V
R5009
2.7
2W
R5010
470
R5130
10k
C593
0.22
Q514
2SC2362
C584
270p
C573
0.1
11
R578
1k
CN501
6P
R591
5.6k
R5126
1.8k
Q549
RN1203
C583
33
100V
R574
15k
D534
1N4148
Q544
2SA1358
R5131 C585
820k 220p
1kV
+12V
D531
1N4148
Q548
2SA733
R5128
22
1/2W
R575
3.3k
2
R5104
27k
D530
1N4148
R5127
3.3
1/2W
bc6
+80VF
Q547
2SC945
Q543
2SC3421
1.0
SG501
1.2KV
D513
BYV26C
V DY+
V DY-
R5134
12
FOCUS
bc2
T503
CN503
+5V
E
FB507
10µH
C517
200p
3kV
D519
PS104R
5
R533
1.3k
1W
HFLB
C518
1500p
1kV
R537
15k
1/2W
4
9
R566
10k
3
8
2
7
1
6
C550
0.01
250V
FB504
3µH R524
8.2k
R536
1.1k
2W
C549
220
25V
R535
1k
1W
F
D503
31DF4
R565
200
+17V
R540 C556
1M 100
1/2W 250V
D502
MTZJ15A
95.7
R531
4.7k
D535
1N4148
58.9
3.1
Q540
2SC945
RELAY DRIVE
C547
0.056
250V
R564
220k
R595
4.7k
Q518
2SB649A
H CENT DRIVE
C582
0.1
R534
2.7
2W
1.2
Q519
2SC2688
H CENT
R557
2.7
2W
L506
10mH
D526
1SS119
6.1
T502
C523
470
25V
2.5
1
10
2
9
3
8
C542
R580 0.022
100 100V
C555
0.1
50V
4
7
5
6
R582
2.7k
4.2
R527
10k
D506
1SS119
R526
4.7k
92.8
D507
SB140 -0.4
R530
1.3 2W
Q502
IRFU110
56.4 H DRIVE OUT
5.3
6.0
S
R528
120
1/2W
C543
1000p
100V
16
Q503
2SC5445
H OUT
R583
1.3 2W
+12V
D508
DD84RC
R532
47
1/2W
FB505
2µH
+12V
C524
0.1
250V
C521
4300p
1.8kV
C565
2.2
250V
R568
10k
3.3
Q512
RN1203
BOP CONT
R560
150k
R518
510k
Q513
2SA733
BOP CONT
R517
10k
D517
1SS119
R549
10k
C560
0.1
C541
4.7
+12V
C527
0.2
250V
C522
0.24
400V
L5200
1.2mH
R550
10k
Q507
IRF640
0
Q505
2SC945
S-CAP
CHANGE
L501
1.2mH
C538
0.1
100V
Q506
IRF640
S-CAP CHANGE
S
R5115
100k
1/2W
C557
0.1
Q537
2SC945
S-CAP
CHANGE
0.6
0.6
R538
4.7k
R5119
4.7k
S
R545
100k
1/2W
C528
0.1
Q508
2SC945
S-CAP
CHANGE
R5200
51
1W
R546
100k
S
R548
4.7k
C529
0.1
CS4
Q509
2SC945
Q510
2SA733
BOP CONT
2.9
D510
1SS119
R544
100k
1/2W
R5118
10k
C566
1.6
250V
43.9
0
S
+12V
D518
1SS119
C526
0.39
250V
Q536
IRF640
S-CAP CHANGE
R539
10k
44.6
R597
51
1W
BOP
+12V
C525
0.12
250V
Q524
IRF640
S-CAP CHANGE
Q521
2SA733
H DRIVE
D539
1N4148
D514
PG104R
5
57.8
Q527
2SC945
H DRIVE
5.4
HUNLOCK
2
R587
Q516
2SA733
B DRIVE
Q520
2SC945
H DRIVE
Q523
2SD1640Q
H DRIVE
D504
1SS119
R5001
82
H
D524
1SS119
0.6
R525
120
Q515
2SC945
B DRIVE
BDRV
14 13
L505
4.5µH
3
1
-77.3
C515
0.1
250V
15
DY+
DYDYDYDY+
DY+
95.6
FB501
3µH
+12V
RY501
R5117
33
V
V
H
H
H
H
4
96.2
D512
ER206
L503
10mH
92.7
S
157.5
HDRV
C548
220
25V
FB508
10µH
Q501
SFS9634
SWITCHING
+12V
102.9
+200V
G
D511
ER206
10
R543
270
1W
L504
32µH
Q517
2SD669A
H CENT DRIVE
6
5
4
3
2
1
R547
4.7k
C5200
47
160V
MUTE
CN502
4P
D541
1N4148
D525
HZ6C3
R567
10k
ab4
1
2
3
4
Q511
H2N6718L
SW
CS2
CS3
CS0
CS1
TO A BOARD
CN304
B-SS3578<U/C>-D..-P2-EPS05
I
• Divided circuit diagram
One sheet of D board circuit diagram is divided into six
sheets, each having the code D-a to D-f. For example, the
destination ab1 on the D-a sheet is connected to ab1 on the
D-b sheet.
a
b
• D - b BOARD WAVEFORMS
qa
qs
qf
qd
qg
qh
1
Ref. No.
58.0 Vp-p (V)
1.8 Vp-p (V)
1k Vp-p (H)
62.0 Vp-p (H)
12.0 Vp-p (H)
120 Vp-p (H)
Circuit diagram division code
5-17
5-18
V.DY
H.DY
1
3
2
A
4
5
6
7
8
10
9
11
12
13
D-c (HV)
+12V
R593
JW
bc2
B
bc1
+81V
FB502
5.2µH
C564
47
25V
D533
1SS119
IC502
UC3843
PWM CONT
FB
VREF
R5142
100 2W
C554
680p
7
R569
680
VCC
OUT
6
C
R584
5.6k
D516
1S119
3
R554
15
ISENSE
GND
OSC
T501
FBT
C537
6800p
2kV
D521
31DF4
D515
BYV26C
C536
1500p
1kV
Q522
2SK2843
R555
180
R561
47k
5
4
C562
0.1
ac1
R519
100 2W
C539
100
100V
8
1
COMP
2
C558
0.1
100V
D529
1N4148
Q539
2SC945
SYNC BUFF
C559
2200p
100V
D
C546
56p
9
12
11
10
14
8
VF1
TO
PICTURE TUBE
C530
0.1
100V
VF2
R559
1k
bc5
13
6
R579
2.2k
R5003
10k
R558
10k
Q538
2SC945
SYNC BUFF
R5133
10k
HV
7
S
R570
2.2k
1
C553
470p
R520
0.22
2W
D536
SB140
D509
PS104R
3
VR501
100k
16
15
R556
10k
C561
680p
C535
100
16V
R521
5.23k
bc4
4
R594
120K
R553
100k
E
R5100
100k
HV ADJ
C533
1
R515
78.7k
Q525
2SA733
OVP
D538
MTZJ18C
C532
0.047
100V
R551
7.32k
Q534
2SC945
OVP
bc3
C545
10
C540
0.1
bc6
R552
100k
CN504
1P
D528
D537
R5143
0.12 RGP02-18 RGP02-18
1
R5144
10k
R5132
JW
TO A BOARD
CN309
C567
0.01
2kV
F
R598
34k
R599
2.61k
1%
G
C599
220
50V
B-SS3578<U/C>-D..-P3-EPS05
• Divided circuit diagram
One sheet of D board circuit diagram is divided into six
sheets, each having the code D-a to D-f. For example, the
destination ab1 on the D-a sheet is connected to ab1 on the
H
D-b sheet.
a
b
1
Ref. No.
Circuit diagram division code
I
Schematic diagram
Ò D
-b board
Schematic diagram
5-19
D
-c board
l
1.2kV
5-20
14
1
3
2
A
4
5
6
7
8
10
9
11
12
13
D632
1N4148
ad1
ad2
SW601
C640
0.1
250V
F601
4A
250V
FB612
600µH
D601
D4SB60L-F
AC RECT
LF601
22mH
POWER
CN601
AC-SOCKET
4
1
L
FB613
600µH
G
3
B
T601
6
3
4
5.9
1
18
2
17
D619
1SS119
FB614
3µH
D621
BYU26C
2
FB616
3µH
C604
470p
250V
FB609
3µH
3
C606
330
450V
VA603
D617
PG104R
FB605
JW
FB615
3µH
D623
UF5406
TH601
10
C603
470p
250V
1
R601 C602
560k
1
1/2W 250V
VA601
RY601
DGC
NC
DGC
1
2
3
TH602
DGC
4
6
3
5
2
1
C
C618
10
50V
R629
1k
1/4W
0.1
C619
0.1
50V
+15V
R628
62
1/4W
16.5
R630
3.9k
C610
4700
250V
C649
4700p
400V
4
15
5
14
6
13
FB621
3µH
7
12
C620
100p
1kV
R653
220
2W
8
11
9
10
R605
75k 2W
R610
10
D606
1SS119
R611
18
Q615
2SC945P
RELAY DRIVE
R655
3.3k
D605
UF4007
C607
220
35V
FB602
2µH
R678
1.5M
R609
2.7k
1/4W
D607
RD27EB4
R624
9.1k
R626
10k
C615
100
16V
L603
100µH
FB608
3µH
VAEF
8
FB
Vcc
D613
ER206
FB617
2µH
C626
100
250V
1%
R614
0.22
2W
C623
100p
C622
2200p
2.5
A
OSC
D629
1SS119
GND
R612
4.99k
1%
+16V
R405
JW
R
R641
470
1.1
R627
4.12k
R675
107k
1%
R643
115k
1%
IC603
TL431
VOLTAGE
FEED BACK
R410
1.5
1W
R644
2.8k
1%
E
R677
1M
D630
1SS119
IC607
LM7812
+12V REG
1
C612
0.01
100V
IN OUT
GND
3
2
C646
1000
20V
C654
22
25V
C613
270p
50V
IC602
TLP621Y
VOLTAGE
FEED BACK
5.0
4
1
3
2
1.7
C616
0.1
50V
R642
220
1/4W
C634
1000
16V
R645
JW
de1
5.3
R620
1k
de2
F
de3
de4
D-d
(POWER SUPPLY)
G
H
B-SS3578<U/C>-D..-P4-EPS05
• Divided circuit diagram
One sheet of D board circuit diagram is divided into six
sheets, each having the code D-a to D- f. For example, the
destination ab1 on the D-a sheet is connected to ab1 on the
D-b sheet.
a
b
1
Ref. No.
Circuit diagram division code
I
5-21
VIDEO+81V
AGND
+12V
HEATER
ABL
+5V
AGND
TO A BOARD
CN303
C652
2200p
500V
R640
100k
5.3
ISENSE OUT
1
2
3
4
5
6
7
+5V
D628
ER206
7.1
R619
10k
CN603
7P
L607
100µH
0.1
R670
1.5M
2.5
D609
1SS119
+81V
L604 +200V
100µH
FB619
2µH
0.4
0.1
R623
100
bd1
R647
JW
6
0.1
COMP
C625
220
100V
K
G
K
R618
10k
Q602
2SK2607
SWITCHING
+16V
L602
100µH
L605
C639
1000p 1kV
5
A
D610
1SS119
Q601
2SA733
SW
7
2.1
D608
RD27EB4
1
2.6
18.7
C651
1000
25V
D615 100µH
D631
UF5404G UF5404G
5.0
3.4
2
D
C611 R616
680p 4.22k
50V
1%
IC601
KA3842
PWM CONTROL
R625
10k
3
IC606
HXL1225-AB
C614
0.1
50V
4
R621
220
C630
1000
25V
D616
31DF2
FB622
3µH
7.0
R656
10k
C628
2200
25V
FB601
3µH
124.4
R615
1.82k
R622
220
4.9
-15V
FB607
3µH
S
Q608
RN1203
+6.3V SW CONT
R669
1
1W
C609
0.33
630V
C608
0.1 400V
C648
4700p
400V
L609
100µH
D611
1SS119
C650
0.022
630V
R652 2.6
100
L601
100µH
16
FB606
3µH
CN602
3P
L608
T603
L606
15µH
C601
0.47
250V
N
Q607
2SA966
+6.3V SW
C645
470
16V
5-22
14
5
6
7
8
10
9
D-e(H.CONV,V.CONV)
R5135
10k
11
12
13
+12V
C586
10
R5141
10k
IC504(2/2)
LM358
A
4
R5138
3
2
51k
1
6
8
7
CN506
2P
1
2
R5140
Q545
2SD667
430
1/4W
R5139
100
C597
0.22
50V
C587
0.1
B
R5136
10.5k
5
20
19
18
VCC
AO4
AO3
AO2
-15V
C588
3300p
17
GND
VDD
16
Vrefu1
CS2
R5137
68k
15
VrefL
CS0
CS1
14
AO8
C594
0.1
13
AO7
Q546
2SB647
+5V
AO1
12
1
2
3
4
5
R4001
150
AO6
6
+5V
AO5
7
C4012
100p
SDA
8
C4011
100p
SCL
9
C
R
10
SDA
SCL
PMG0
R4011
4.7k
R4012
4.7k
D
IC4000
M62393P
+5V
Vrefu2
11
ae1
4
de1
+5V
IC6000
TOP223Y
FB618
3µH
R6010
13
D6000
1SS119
F
ZD6001
HZ27V-2
C6000
100
16V
D6002
PS104R
D6003
PS104R
C6001
47
50V
2
7
1
6
4A
D6005
F10P06Q
PH6000 R6002
160
TLP621Y
R6001 R6003
75
330
C6005
0.01
50V
IC6001
TL431
R6004
3.4k
1/4W
R6006
10k
L6000
5.2µH
C6003
4700
16V
2
PH6001
TLP621Y
2
8
1
R6005
3.16k
1/4W
R6007
R4113
56k
1/4W
R4114
20k
C6004
470
16V
C4006
0.1
2
1
3
C6002
0.1uF
50V
R4112
10k
1/4W
8
3
R6008
220
3
4
R4117
5.23k
1/4W
R4119
30R
2W
R4118
100
1/4W
Q4004
2SB649
Q6000
RN1001
R4007
82k
1/4W
6
IC4001
LM358
AMP
8
7
Q4001
HSD669A
R4009
100
5
C4001
10
16V
R4115
24.9k
100k
1/4W
9
R4116
15k
1/4W
R4006
4
de3
C6006
220
16V
100µH
CHOKE
T6000
5
C4002
47
25V
Q4003
2SD669A
IC4002
LM358
AMP
1/4W
E
C6007
2200p
1kV
+15V
C4010
220
16V
20K
1/4Ws
D6001
BYV26C
L6001
D620
JW
R4005
R6009
27k
2W
R4003
10k
de2
4
R4008
12.4k
1/4W
R4110
30
2W
Q4002
2SB649
C4005
0.22
50V
R4111
14.3k
1/4W
CN4001
4P
1
2
3
4
C4003 100V
100
C4007
0.1
100V
C4009
100
25V
L507
100µH
-15V
C4008
0.1
100V
0.1
-15V
de4
G
B-SS3578<U/C>-D..-P5-EPS05
• Divided circuit diagram
One sheet of D board circuit diagram is divided into six
sheets, each having the code D-a to D-f. For example, the
destination ab1 on the D-a sheet is connected to ab1 on the
H
D-b sheet.
a
b
1
Ref. No.
Circuit diagram division code
I
Schematic diagram
Ò D
-d board
Schematic diagram
5-23
D
-e board
l
5-24
14
6
7
8
CONTROL)
1
2
3
4
5
6
7
R7002
1.5k
R7000
18
L7001
0.45µH
L7002
0.45µH
L7003
1µH
L7005
JW
P8D1
7P
V2
V1
P2
M2
P1
M1
DGND
P7D1
7P
V2
V1
P2
M2
P1
M1
DGND
1
2
3
4
5
6
7
+ C7013
330
10V
1
R7028 24
2
R7029 24
3
4
1 V3.3
C7030
0.01
PSW1 32
L7034
2.3µH
L7015
1µH
5VF
DP2 31
3 GND
DM2 30
L7021
0.45µH
L7022
0.45µH
L7016
1µH
4 DM3
5 DP3
DM0 28
6 VCC
DP1 27
R7012
1k
8 OC2_N
DP5 25
R7019
1M
9 OC3_N
R7022
FLGB 3
1
R7032 24 1/4W
2
330
R7033 24 1/4W
3
4
L7030 2.3µH
P7004
4P
12 DM4
L7012
1µH
L7013
1µH
ENB 4
IC7002
MIC2526
POWER SWITCH
5VF
L7014
2.3µH
RESET_N 21
1
C7006 22p
L7031
0.45µH
2
13 DP4
XTAL2 20
D7000
HZ5.1B
3
14 SP/BP_N
XTAL1 19
15 HUBGL_N
PSW5 18
X7000
6MHz
L7033
2.3µH
C7008 3.3
R7018
1M
R7025
100k
R7017
15k
16 PSW3
PSW4 17
R7035 24
4
C7007 22p
5VF
F
R7034 24
L7032
0.45µH
R7027
5 OUTB
3.3k
R7024
0
OPTION/SDA 22
P7003
4P
2.3µH
INDV/SCL 23
R7015
100k
C7004
0.1
C7005
0.1
11 OC5_N
C7022
0.1
50V
C7024 47p
FLGA 2
C7003
0.1
C7002
0.1
ENA 1
6 GND
5VF
R7020
1M
2.3µH
L7029
+
5VF
7 IN
L7027
0.45µH
DM5 24
5VF
R7014
1k
10 OC4_N
E
L7028
+ C7021
330
10V
0.1
R7010 10k
R7009 10k
R7008 10k
R7007 10k
R7013
1k
L7026
0.45µH
1
2
3
4
5
6
7
50V
1
2
3
4
5
6
7
DM1 26
P7D2
7P
P3
M3
DGND
V4
V3
M4
P4
10V
L7018
1µH
7 OC1_N
P8D2
7P
P3
M3
DGND
V4
V3
M4
P4
C7018 47p
C7000
+
220
10V
R7011
1k
USB DB_A BLOCK
L7017
1µH
L7011
JW
5VF
8 OUTA
C7012 47p
C7011 47p
4
C7017 47p
ENB 4
3
R7031 24
L7025 2.3µH
C7023 47p
D
FLGB 3
2
L7024 JW
DP0 29
5VF
5 OUTB
R7030 24
L7010
1µH
FLGA 2
6 GND
L7023
0.45µH
+
ENA 1
P7002
4P
1
L7009
1µH
L7035
2.3µH
IC7001
MIC2526
POWER SWITCH
7 IN
C7001 220V
R7006 10k
R7005 10k
R7004 10k
R7003 10k
C
2 PSW2
L7008
2.3µH
5VF
8 OUTA
P7001
4P
C7014
0.1
50V
L7007
2.3µH
B
5VF
C7016
0.1
50V
+ C7015
330
10V
IC7000
ISP1122
USB CONT
3.3V
13
L7019
2.3µH
R7016
15k
L7004
JW
12
L7020
2.3µH
L7006
JW
R7001
18
11
C7020
1
2
3
4
10
9
C7019
P7000
4P
NC
USB DM
USB DP
GND
TO D-a BOARD
CN904
5
3.3V
D-f(USB
A
4
C7010 47p
3
2
C7009 47p
1
+
USB DB_B BLOCK
B-SS3578<U/C>-D..-P6-EPS05
R7026
3.3k
G
H
• Divided circuit diagram
One sheet of D board circuit diagram is divided into six
sheets, each having the code D-a to D- f. For example, the
destination ab1 on the D-a sheet is connected to ab1 on the
D-b sheet.
a
b
1
Ref. No.
Circuit diagram division code
I
5-25
5-26
14
5-5. SEMICONDUCTORS
M51951BSL
IRFU110
IRFU110A
2SA733-QP
2SA733TP-QP
2SA966-Y
2SB647A-C
2SC2655
2SC945-P
2SD669AVC
-
~
~-
-
n
MAA3371X
D4SB60L
D4SB60L-F
-
BH3863F
BH3863F-E2
-
1
~
G
TOP VIEW
~
D
24 pin SOP
n
IRF640
1
E C
B
TOP VIEW
36 pin DIP
2SB649-C
2SB649
2SC2688-LK
PC123F2
1
4
3
7
G
D
LETTER SIDE
S
1
LM2415T
2
MCR100-6
ST72774
E
C B
n
1
TOP VIEW
TDA4841
GATE
D2L40-TA
ER106
HSS82
HZ12
HZ5C1
HZ5C2
MTZJ-T-73-15A
PS104R
RD27EB4
SB140-6339
UF4007G23
UF5402G
UF5404G
UF5406
10E2
1N4002
1N4004
1N4148
2SC2655-Y
CATHODE
42 pin DIP
LM358N
M24C16BN6
UC3842A
UC3843A
24LC21/P
CATHODE
ANODE
SEL4225R-D
CATHODE
2N3904
ANODE
ANODE
TOP VIEW
E C
B
32 pin DIP
CATHODE
BF420
E B
C
TOP VIEW
8 pin DIP
CATHODE
EGP10D
n
1
MTZJ-15A
MTZJ-5.1A
MTZJ-5.1B
RD15ES-B1
RD5.1ESB2
1SS119-25
1SS119-25TD
ANODE
n
1
CATHODE
ANODE
M52743BSP
LA78040
-
S
TLP621D4-Y-LF2
2SC4632LS-CB7
4
3
2SA1221-L
MCT7812CT
TA7805S
ANODE
1
2
4
3
1
B
E C
B
C
E C
B
DTC124ESA
RN1203
2SC3400
2
LT6463-23-D51
E
BYV26C
U05G
CATHODE
LETTER SIDE
ANODE
(RED)
ANODE
(GRN)
CATHODE
M35047
n
1
ANODE
TOP VIEW
20 pin DIP
E C
B
Schematic diagram
Ò D
-f board
5-27
5-28
HMD-A400
SECTION 6
EXPLODED VIEWS
NOTE:
• Items with no part number and no
description are not stocked because they
are seldom required for routine service.
• The construction parts of an assembled
part are indicated with a collation number
in the remark column.
• Items marked " * " are not stocked since
they are seldom required for routine
service. Some delay should be anticipated
when ordering these items.
The components identified by mark ¡
are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque ¡ sont critiques pour la
sécurité. Ne les remplacer que par une
pièce portant le numéro spécifié.
6-1. CHASSIS
7-685-663-71
7-685-881-09
7-685-648-79
+BVTP 4X16
+BVTT 4X8
+BVTP 3X12
8026114012
8418113010
3
11
1
10
2
5
4
8
9
6
7
REF.NO. PART NO.
1
2
3
4
5
6
DESCRIPTION
* A-1272-334-A A BOARD, COMPLETE
* 4-060-151-01 STOPPER, CABLE
X-4038-727-1 BUCKET ASSY
4-080-736-11 HOLDER, CABLE
* 4-060-150-01 BRACKET, CABLE
X-4038-728-1 COVER ASSY, BOTTOM
REMARK
REF.NO. PART NO.
TU9R6E0242
IQ020X9R51
IQ500D9R51
IQ030X9R51
6-1
7
8
9
10
11
DESCRIPTION
REMARK
4-080-740-11 FOOT, RUBBER
9006099R51
0 1-453-362-11 TRANSFORMER ASSY, FLYBACK
7050309R00
* A-1333-078-A D BOARD, COMPLETE
TU9R6E0412
* 4-081-660-01 LABEL, INFORMATION
9011099R51
1-757-540-11 CABLE, I/O
C7107C2U11
HMD-A400
6-2. PICTURE TUBE
7-685-648-79
+BVTP 3X12
8418113010
59
60
66
67
57
68
69
58
61
63
56
62
64
55
65
54
70
52
53
56
51
The components identified by mark ¡
are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque ¡ sont critiques pour la
sécurité. Ne les remplacer que par une
pièce portant le numéro spécifié.
REF.NO. PART NO.
51
52
53
54
55
56
57
58
59
60
X-4038-726-1
4-080-737-01
4-060-162-01
4-044-932-11
4-073-619-11
DESCRIPTION
REMARK
REF.NO. PART NO.
BEZEL ASSY
SS9R510420
KNOB, POWER
IQA7059R51
SPRING, COMPRESSION 2011097M10
EMBLEM (NO.8), SONY
KNOB, MENU
1QAO059R51
* A-1372-920-A H BOARD, COMPLETE
TU9R6E0344
4-060-155-01 HOLDER, HV CABLE
4-060-166-01 SPACER, DEFLECTION YOKE
4-365-808-01 SCREW (5), TAPPING
4-041-021-11 HOLDER, DEGAUSE COIL
61 0 1-416-282-21 COIL, DEGAUSSING
6-2
DESCRIPTION
REMARK
62
4-060-603-01 SPRING, TENSION
63 0 1-452-912-11 NECK ASSEMBLY
64 0 8-451-520-11 DEFLECTION YOKE (Y19TKK3-M)
65 0 8-736-413-05 PICTURE TUBE 19TKC
66
4-038-870-00 CLIP, LEAD WIRE
67
68
69
70
1-452-032-00
1-452-094-00
4-051-736-21
8-734-028-06
MAGNET, DISK; 10mm ø
MAGNET, ROTATABLE DISK; 15mm ø
PIECE A (90), CONV. CORRECT
ITC ASSY (19TKC-R2) (SDP)
HMD-A400
6-3. PACKING MATERIALS
107
106
101
104
102 103
108
105
REF.NO. PART NO.
101
X-4038-729-1
102
1-792-032-11
103
4-079-363-21
104 * 4-060-620-01
105 * 4-079-389-01
DESCRIPTION
STAND ASSY
CABLE, USB
MANUAL, INSTRUCTION
BAG, POLYETHYLENE
INDIVIDUAL CARTON
REMARK
REF.NO. PART NO.
SS9R6E0320
C7117R1010
9012099R51
9008095R51
9001099R51
6-3
106
107
108
DESCRIPTION
REMARK
7-685-663-71 SCREW +BVTP 4X16 TYPE2 IT-3
8026114012
4-079-900-01 CUSHION (UPPER) (ASSY) 9002099R6E
4-079-901-01 CUSHION (LOWER) (ASSY)9003099R6E
HMD-A400
MEMO
6-4
SECTION 7
ELECTRICAL PARTS LIST
NOTE:
The components identified ! marked are
critical for safety.
Replace only with the part number specified.
Les composants identifiés par la marque !
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
When indicating parts by reference
number, please include the board name.
• Items marked " * " are not stocked since
they are seldom required for routine
service. Some delay should be anticipated
when ordering these items.
RESISTORS
• All resistors are in ohms
• F : nonflammable
CAPACITOR
• MF : µF
COIL
• UH : µH
• All variable and adjustable resistors have
characteristic curve B, unless otherwise
noted.
HMD-A400(E)
7-1
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
#
Board
Type
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
! / * Ref. No.
C002
C004
C005
C006
C008
C009
C010
C011
C012
C013
C014
C015
C016
C017
C019
C022
C023
C025
C026
C027
C028
C029
C030
C031
C032
C033
C034
C035
C036
C037
C038
C039
C040
C041
Part No.
Service
1-126-934-11
1-164-489-11
Pending
1-115-339-11
1-137-995-11
1-104-664-11
1-115-339-11
1-128-582-11
1-130-777-11
1-115-339-11
Pending
1-107-823-11
1-163-009-11
1-130-777-11
1-130-777-11
1-163-131-00
1-135-393-11
1-115-339-11
Pending
Pending
1-163-263-11
1-137-872-11
Pending
1-115-339-11
1-135-398-11
1-163-017-00
1-115-339-11
1-135-393-11
Pending
1-164-489-11
1-104-664-11
1-126-933-11
1-137-970-11
1-163-259-91
Production
1-126-934-91
1-164-489-91
Pending
1-115-339-91
1-137-995-11
1-104-660-91
1-115-339-91
1-128-582-91
1-137-961-11
1-115-339-91
Pending
1-107-823-91
1-163-009-91
1-137-961-11
1-137-961-11
1-163-265-91
1-135-393-11
1-115-339-91
Pending
Pending
1-163-263-91
1-137-872-11
Pending
1-115-339-91
1-135-398-11
1-163-017-91
1-115-339-91
1-135-393-11
Pending
1-164-489-91
1-104-660-91
1-126-933-91
1-137-970-11
1-163-259-91
Description
ELECT 220MF 16V
CERAMIC CHIP 0.22MF 16V
ELECT 470MF 16V
CERAMIC CHIP 0.1MF 50V
CERAMIC 0.1MF 50V
ELECT 47MF 16V
CERAMIC CHIP 0.1MF 50V
ELECT 10MF 100V
MYLAR 0.1MF 100V
CERAMIC CHIP 0.1MF 50V
CERAMIC 0.01MF 2KV
CERAMIC CHIP 0.47MF 16V
CERAMIC CHIP 1000pF 50V
MYLAR 0.1MF 100V
MYLAR 0.1MF 100V
CERAMIC CHIP 390pF 50V
ELECT 100MF 10V
CERAMIC CHIP 0.1MF 50V
CERAMIC 5600pF 50V
CERAMIC CHIP 330pF 50V
CERAMIC CHIP 330pF 50V
CERAMIC 1000pF 50V
ELECT 470MF 16V
CERAMIC CHIP 0.1MF 50V
ELECT 1MF 50V
CERAMIC CHIP 4700pF 50V
CERAMIC CHIP 0.1MF 50V
ELECT 100MF 10V
CERAMIC CHIP 0.01MF 50V
CERAMIC CHIP 0.22MF 16V
ELECT 47MF 16V
ELECT 100MF 16V
MYLAR 0.01MF 100V
CERAMIC CHIP 220pF 50V
Remarks-1
5156221T16
7144224106
515X471T16
7146104456
5134104452
515X470T16
7146104456
5156100T01
5075104501
7146104456
51011031C3
7144474106
7144102256
5075104501
5075104501
7183391556
5156101T10
7146104456
5101562152
7144331156
7183331556
5101102152
515X471T16
7144104156
5156109T50
7144472156
7146104456
5156101T10
7146103456
7144224106
5156470T16
5156101T16
5077103501
7183221556
Remarks-2
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-2
No.
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
#
Board
Type
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
! / * Ref. No.
C043
C045
C046
C047
C048
C049
C054
C055
C056
C101
C102
C103
C104
C105
C106
C107
C108
C109
C110
C120
C201
C202
C203
C204
C206
C207
C210
C301
C302
C303
C304
C306
C307
C310
Part No.
Service
Pending
Pending
1-115-339-11
1-115-339-11
1-135-383-11
1-126-934-11
1-115-339-11
1-163-239-11
1-163-239-11
1-163-235-11
1-126-964-11
1-115-339-11
1-115-339-11
1-115-339-11
1-135-383-11
1-137-995-11
1-115-339-11
1-163-259-91
1-163-251-11
1-137-995-11
1-163-235-11
1-126-964-11
1-115-339-11
1-115-339-11
1-135-383-11
1-137-995-11
1-163-251-11
1-163-235-11
1-126-964-11
1-115-339-11
1-115-339-11
1-135-383-11
1-137-995-11
1-163-251-11
Production
Pending
Pending
1-115-339-91
1-115-339-91
1-135-383-11
1-126-934-91
1-115-339-91
1-163-239-91
1-163-239-91
1-163-235-91
1-126-964-91
1-115-339-91
1-115-339-91
1-115-339-91
1-135-383-11
1-137-995-11
1-115-339-91
1-163-259-91
1-163-251-91
1-137-995-11
1-163-235-91
1-126-964-91
1-115-339-91
1-115-339-91
1-135-383-11
1-137-995-11
1-163-251-91
1-163-235-91
1-126-964-91
1-115-339-91
1-115-339-91
1-135-383-11
1-137-995-11
1-163-251-91
Description
4.7MF 50V
CERAMIC 0.01MF 1.5KV
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 0.1MF 50V
MYLAR 0.1MF 100V
ELECT 220MF 16V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 33pF 50V
CERAMIC CHIP 33pF 50V
CERAMIC CHIP 22pF 50V
ELECT 10MF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 0.1MF 50V
MYLAR 0.1MF 100V
CERAMIC 0.1MF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 220pF 50V
CERAMIC CHIP 100pF 50V
CERAMIC 0.1MF 50V
CERAMIC CHIP 22pF 50V
ELECT 10MF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 0.1MF 50V
MYLAR 0.1MF 100V
CERAMIC 0.1MF 50V
CERAMIC CHIP 100pF 50V
CERAMIC CHIP 22pF 50V
ELECT 10MF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 0.1MF 50V
MYLAR 0.1MF 100V
CERAMIC 0.1MF 50V
CERAMIC CHIP 100pF 50V
Remarks-1
5164479T50
5104103463
7146104456
7146104456
5075104501
5156221T16
7144104156
7183330556
7183330556
7183220556
5156100T50
7146104456
7146104456
7146104456
5075104501
5134104452
7146104456
7183221556
7183101556
5134104452
7183220556
5156100T50
7146104456
7146104456
5075104501
5134104452
7183101556
7183220556
5156100T50
7146104456
7146104456
5075104501
5134104452
7183101556
Remarks-2
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-3
No.
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
#
Board
Type
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
! / * Ref. No.
*
*
*
*
*
*
CN301
CN302
CN303
CN304
CN305
CN306
CN307
CN309
CN310
D001
D002
D003
D004
D008
D009
D010
D011
D012
D013
D017
D101
D102
D103
D104
D105
D201
D202
D203
D204
D205
D301
D302
D303
D304
Part No.
Service
1-564-512-11
1-564-512-11
1-564-510-11
1-564-507-11
1-564-5!7-11
1-564-510-11
1-695-915-11
1-506-108-41
1-695-915-11
8-719-911-19
8-719-070-90
8-719-109-85
8-719-070-90
8-719-070-90
8-719-070-90
8-719-070-90
8-719-070-90
8-719-070-90
8-719-070-90
8-719-074-26
8-719-070-90
8-719-070-90
8-719-970-82
8-719-970-82
8-719-970-82
8-719-911-19
8-719-911-19
8-719-970-82
8-719-970-82
8-719-970-82
8-719-911-19
8-719-911-19
8-719-970-82
8-719-970-82
Production
1-564-512-11
1-564-512-11
1-564-510-51
1-564-507-51
1-564-507-11
1-564-510-51
1-695-915-11
1-506-108-41
1-695-915-11
8-719-921-20
8-719-070-90
8-719-921-43
8-719-070-90
8-719-070-90
8-719-070-90
8-719-070-90
8-719-070-90
8-719-070-90
8-719-070-90
8-719-074-26
8-719-070-90
8-719-070-90
8-719-970-82
8-719-970-82
8-719-970-82
8-719-921-20
8-719-921-20
8-719-970-82
8-719-970-82
8-719-970-82
8-719-921-20
8-719-921-20
8-719-970-82
8-719-970-82
Description
PLUG, CONNECTOR 9P
PLUG, CONNECTOR 9P
PLUG, CONNECTOR 7P
PLUG, CONNECTOR 4P
PLUG, CONNECTOR 4P
PLUG, CONNECTOR 6P
TAB (CONTACT)
PIN, CONNECTOR (TERMINAL PIN)
TAB (CONTACT)
DIODE 1SS119-25
DIODE 1N4148
ZENER DIODE RD5.1ESB2
DIODE 1N4148
DIODE 1N4148
DIODE 1N4148
DIODE 1N4148
DIODE 1N4148
DIODE 1N4148
DIODE 1N4148
DIODE ER106
DIODE 1N4148
DIODE 1N4148
DIODE HSS82
DIODE HSS82
DIODE HSS82
DIODE 1SS119-25
DIODE 1SS119-25
DIODE HSS82
DIODE HSS82
DIODE HSS82
DIODE 1SS119-25
DIODE 1SS119-25
DIODE HSS82
DIODE HSS82
Remarks-1
Remarks-2
4490900330
4490900330
4490700330
4490400330
4490411330
4490600330
4490100209
3340236016
4490100209
4120511900
412014148T
41205051BU
412014148T
412014148T
412014148T
412014148T
412014148T
412014148T
412014148T
4130101060
412014148T
412014148T
4130190820
4130190820
4130190820
4120511900
4120511900
4130190820
4130190820
4130190820
4120511900
4120511900
4130190820
4130190820
Sony
Sony
Sony
Sony
Difference
Sony
Sony
Sony
Others
Others
Others
Others
Others
Others
Others
Others
Others
Others
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-4
No.
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
#
Board
Type
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
DIODE
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
IC
IC
IC
IC
IC
JACK
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
TRANSISTOR
TRANSISTOR
! / * Ref. No.
!
D305
FB001
FB002
FB003
FB004
FB005
FB006
FB008
FB009
FB010
FB011
FB012
FB115
FB215
FB315
IC001
IC002
IC003
IC004
IC005
J001
JW034
JW035
JW036
L001
L002
L101
L102
L201
L202
L301
L302
Q001
Q002
Part No.
Service
8-719-970-82
1-535-303-31
1-469-403-11
1-469-403-11
1-469-995-11
1-469-995-11
1-469-402-11
1-500-104-21
1-500-104-21
1-500-104-21
1-500-104-21
1-500-104-21
1-500-104-21
1-500-104-21
1-500-104-21
8-759-582-06
Pending
6-800-343-31
8-759-008-70
Pending
1-251-598-11
1-412-911-11
Pending
1-412-911-11
1-469-400-11
1-469-402-11
1-469-398-11
Pending
1-469-398-11
1-469-398-11
1-469-398-11
Pending
8-729-139-04
8-729-139-04
Production
8-719-970-82
1-535-143-11
1-469-403-11
1-469-403-11
1-469-995-11
1-469-995-11
1-469-402-11
1-500-104-21
1-500-104-21
1-500-104-21
1-500-104-21
1-500-104-21
1-500-104-21
1-500-104-21
1-500-104-21
8-759-582-06
Pending
6-800-343-31
8-759-991-16
Pending
1-251-598-11
1-412-911-21
Pending
1-412-911-21
1-469-400-11
1-469-402-11
1-469-398-11
Pending
1-469-398-11
1-469-398-11
1-469-398-11
Pending
8-729-139-04
8-729-139-04
Description
Remarks-1
Remarks-2
DIODE HSS82
JUMP WIRE 0.6_
FERRITE
FERRITE
PEAKING COIL 150UH
PEAKING COIL 150UH
INDUCTOR 3UH
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
IC M52743BSP
IC LM2412T
M35047-061SP
IC LM358N
IC ST24LC21B1
SOCKET, PICTURE TUBE
FERRITE 1.1UH
PEAKING COIL 150UH
FERRITE 1.1UH
INDUCTOR 100UH
INDUCTOR 3UH
INDUCTOR 0.1UH
INDUCTOR 0.22UH
INDUCTOR 0.1UH
INDUCTOR 0.1UH
INDUCTOR 0.1UH
INDUCTOR 0.22UH
TRANSISTOR 2N3904
TRANSISTOR 2N3904
4130190820
5406100000
4322209046
4322209046
4321151006
4321151006
4322309006
4328350006
4328350006
4328350006
4328350006
4328350006
4328350006
4328350006
4328350006
4159527432
41592412T0
4159350473
4159358000
4159242100
4570307C2U
7099159250
432B151006
7099159250
432B101006
4322309006
432B108006
432B228006
432B108006
432B108006
432B108006
432B228006
4111139040
4111139040
Sony
Sony
Difference
Others
Others
Others
Others
Others
Sony
Sony
Sony
Others
Others
Others
Others
Others
Others
Sony
Sony
HMD-A400(E)
7-5
No.
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
#
Board
Type
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
! / * Ref. No.
Q003
Q004
Q005
Q101
Q201
Q301
R001
R002
R004
R005
R006
R007
R008
R009
R010
R011
R013
R014
R015
R016
R018
R019
R020
R021
R022
R023
R024
R025
R026
R028
R029
R030
R031
R032
Part No.
Service
8-729-139-04
8-729-823-81
8-729-194-57
Pending
Pending
Pending
1-247-807-31
1-247-807-31
1-216-025-11
1-216-049-11
1-216-073-00
1-216-025-11
1-216-058-00
1-216-049-11
1-216-025-11
1-216-041-00
1-216-065-11
1-216-065-11
1-247-816-11
1-216-041-00
1-216-025-11
1-216-025-11
Pending
Pending
1-216-058-00
Pending
Pending
1-249-421-11
1-216-041-00
1-216-049-11
1-216-053-00
1-216-073-00
1-244-274-11
1-216-067-00
Production
8-729-139-04
8-729-823-81
8-729-191-57
Pending
Pending
Pending
1-247-807-91
1-247-807-91
1-216-025-91
1-216-049-91
1-216-073-91
1-216-025-91
1-216-058-91
1-216-049-91
1-216-025-91
1-216-041-91
1-216-065-91
1-216-065-91
1-247-816-91
1-216-041-91
1-216-025-91
1-216-025-91
Pending
Pending
1-216-058-91
Pending
Pending
1-247-839-91
1-216-041-91
1-216-049-91
1-216-053-91
1-216-073-91
1-244-274-11
1-216-067-91
Description
TRANSISTOR 2N3904
TRANSISTOR 2SC4632LS-CB7
TRANSISTOR 2SC945P
TRANSISTOR 2SC1921
TRANSISTOR 2SC1921
TRANSISTOR 2SC1921
CARBON 100 1/4W
CARBON 100 1/4W
RES-CHIP 100 1/10W
RES-CHIP 1K 1/10W
RES-CHIP 10K 1/10W
RES-CHIP 100 1/10W
RES-CHIP 2.4K 1/10W
RES-CHIP 1K 1/10W
RES-CHIP 100 1/10W
RES-CHIP 470 1/10W
RES-CHIP 4.7K 1/10W
RES-CHIP 4.7K 1/10W
CARBON 240 1/4W
RES-CHIP 470 1/10W
RES-CHIP 100 1/10W
RES-CHIP 100 1/10W
RES-CHIP 18K 1/10W
METAL CHIP 12.4K 1/10W
RES-CHIP 2.4K 1/10W
RES-CHIP 300K 1/10W
CARBON 150K 1/4W
CARBON 2.2K 1/4W
RES-CHIP 470 1/10W
RES-CHIP 1K 1/10W
RES-CHIP 1.5K 1/10W
RES-CHIP 10K 1/10W
METAL 22M 1/2W
RES-CHIP 5.6K 1/10W
Remarks-1
Remarks-2
4111139040
4100246320
411020945P
4110219210
4110219210
4110219210
4050510155
4050510155
4010110152
4010110252
4010110352
4010110152
4010124252
4010110252
4010110152
4010147152
4010147252
4010147252
4050524155
4010147152
4010110152
4010110152
4010118352
419A112422
4010124252
4010130452
4050515455
4050522255
4010147152
4010110252
4010115252
4010110352
4160422655
4010156252
Sony
Sony
Sony
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
HMD-A400(E)
7-6
No.
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
#
Board
Type
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
! / * Ref. No.
R033
R034
R035
R036
R037
R039
R042
R046
R101
R102
R103
R104
R105
R106
R107
R108
R109
R110
R111
R112
R113
R115
R120
R201
R203
R204
R207
R208
R209
R210
R211
R212
R213
R215
Part No.
Service
Pending
Pending
1-244-273-11
1-216-025-11
1-216-025-11
1-216-058-00
Pending
1-216-060-91
1-216-022-11
1-216-065-11
1-216-049-11
1-249-399-11
1-216-017-91
1-216-017-91
Pending
1-247-862-11
Pending
1-216-061-00
1-247-903-00
Pending
1-216-041-00
Pending
1-216-017-91
1-216-022-11
1-216-049-11
1-249-399-11
Pending
1-247-862-11
Pending
1-216-061-00
1-247-903-00
Pending
1-216-041-00
Pending
Production
Pending
Pending
1-244-273-11
1-216-025-91
1-216-025-91
1-216-058-91
Pending
1-216-060-91
1-216-022-11
1-216-065-91
1-216-049-91
1-247-795-91
1-216-017-91
1-216-017-91
Pending
1-247-862-91
Pending
1-216-061-91
1-247-903-91
Pending
1-216-041-91
Pending
1-216-017-91
1-216-022-11
1-216-049-91
1-247-795-91
Pending
1-247-862-91
Pending
1-216-061-91
1-247-903-91
Pending
1-216-041-91
Pending
Description
RES-CHIP 180K 1/10W
CARBON 10K 1/2W
METAL 2.2M 1/2W
RES-CHIP 100 1/10W
RES-CHIP 100 1/10W
RES-CHIP 2.4K 1/10W
CARBON 100 1/2W
RES-CHIP 3K 1/10W
RES-CHIP 75 1/10W
RES-CHIP 4.7K 1/10W
RES-CHIP 1K 1/10W
CARBON 33 1/4W
RES-CHIP 47 1/10W
RES-CHIP 47 1/10W
CARBON 5.1K 1/4W
CARBON 20K 1/4W
RES-CHIP 510 1/10W
RES-CHIP 3.3K 1/10W
CARBON 1M 1/4W
CARBON 120 1/2W
RES-CHIP 470 1/10W
CARBON 120 1/2W
RES-CHIP 47 1/10W
RES-CHIP 75 1/10W
RES-CHIP 1K 1/10W
CARBON 33 1/4W
CARBON 5.1K 1/4W
CARBON 20K 1/4W
RES-CHIP 510 1/10W
RES-CHIP 3.3K 1/10W
CARBON 1M 1/4W
CARBON 120 1/2W
RES-CHIP 470 1/10W
CARBON 100 1/2W
Remarks-1
4010118452
4060210315
4160222555
4010110152
4010110152
4010124252
4060210115
4010130252
4010175002
4010147252
4010110252
4050533055
4010147052
4010147052
4050551255
4050520355
4010151152
4010133252
4050510555
4060212115
4010147152
4050112155
4010147052
4010175002
4010110252
4050533055
4050551255
4050520355
4050551155
4010133252
4050510555
4060212115
4010147152
4050110155
Remarks-2
Difference
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-7
No.
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
#
Board
Type
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
SPARK GAP
SPARK GAP
SPARK GAP
SPARK GAP
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
! / * Ref. No.
R301
R303
R304
R307
R308
R309
R310
R311
R312
R313
R315
SG001
SG101
SG201
SG301
C401
C402
C403
C404
C405
C406
C408
C409
C502
C503
C504
C505
C506
C507
C508
C509
C510
C512
C513
Part No.
Service
1-216-022-11
1-216-049-11
1-249-399-11
Pending
1-247-862-11
Pending
1-216-061-00
1-247-903-00
Pending
1-216-041-00
Pending
Pending
1-517-499-11
1-517-499-11
1-517-499-11
1-137-869-11
1-126-941-11
Pending
1-107-914-11
1-137-969-11
1-137-413-11
1-126-951-11
1-137-410-11
1-137-399-11
1-137-399-11
1-137-150-11
1-137-968-11
1-137-150-11
1-137-391-11
1-163-251-11
Pending
1-126-767-11
1-163-259-91
1-163-259-91
Production
1-216-022-11
1-216-049-91
1-247-795-91
Pending
1-247-862-91
Pending
1-216-061-91
1-247-903-91
Pending
1-216-041-91
Pending
Pending
1-517-499-11
1-517-499-11
1-517-499-11
1-137-869-11
1-126-941-91
Pending
1-126-942-91
1-137-969-11
1-137-413-91
1-126-951-91
1-137-410-91
1-137-422-91
1-137-422-91
1-137-393-91
1-137-968-11
1-137-393-91
1-137-391-91
1-163-251-91
Pending
1-126-767-91
1-163-259-91
1-163-259-91
Description
RES-CHIP 75 1/10W
RES-CHIP 1K 1/10W
CARBON 33 1/4W
CARBON 5.1K 1/4W
CARBON 20K 1/4W
RES-CHIP 510 1/10W
RES-CHIP 3.3K 1/10W
CARBON 1M 1/4W
CARBON 120 1/2W
RES-CHIP 470 1/10W
CARBON 120 1/2W
SPARK GAP
GAP, SPARK
GAP, SPARK
GAP, SPARK
MYLAR 0.1MF 250V
ELECT 470MF 25V
MYLAR 0.022MF 100V
ELECT 1000MF 25V
FILM 0.22MF 50V
MYLAR 3300pF 100V
ELECT 470MF 35V
MYRAR 1000pF 100V
MYRAR 0.1MF 100V
MYRAR 0.1MF 100V
MYLAR 0.01MF 100V
MYRAR 0.1MF 50V
MYLAR 0.01MF 100V
MYLAR 4700pF 100V
CERAMIC CHIP 100pF 50V
3300pF 100V
ELECT 1000MF 16V
CERAMIC CHIP 220pF 50V
CERAMIC CHIP 220pF 50V
Remarks-1
Remarks-2
4010175002
4010110252
4050533055
4050551255
4050520355
4050551155
4010133252
4050510555
4060212115
4010147152
4050112155
5106122204
4705415201
4705415201
4705415201
5074104102
5156471S25
5075223501
515X102S25
5110224550
5116332111
515X471T35
5116102111
5075104501
5075104501
5116103511
5110104550
5116103511
5116472511
7183101556
5090332515
5156102S16
7183221556
7183221556
Sony
Difference
Sony
Sony
Sony
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-8
No.
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
! / * Ref. No.
C514
C515
C517
C518
C521
C522
C523
C524
C525
C526
C527
C528
C530
C531
C532
C533
C534
C535
C536
C537
C538
C539
C540
C541
C542
C543
C545
C546
C547
C548
C549
C550
C553
C554
Part No.
Service
1-115-339-11
1-137-869-11
1-137-929-11
1-137-876-11
Pending
Pending
1-126-941-11
Pending
1-136-190-11
Pending
Pending
1-115-339-11
1-137-399-11
Pending
1-137-962-11
1-135-398-11
1-115-339-11
1-126-968-11
Pending
Pending
1-137-399-11
1-128-563-11
1-115-339-11
1-135-395-11
Pending
1-137-873-11
1-126-964-11
Pending
Pending
1-104-666-11
1-104-666-11
1-135-352-11
1-163-133-00
Pending
Production
1-115-339-91
1-137-869-11
1-137-929-11
1-137-876-11
Pending
Pending
1-126-941-91
Pending
1-136-190-11
Pending
Pending
1-115-339-91
1-137-422-91
Pending
1-137-962-11
1-135-398-11
1-115-339-91
1-126-968-91
Pending
Pending
1-137-422-91
1-128-563-91
1-115-339-91
1-135-395-11
Pending
1-137-873-11
1-126-964-91
Pending
Pending
1-104-666-91
1-104-666-91
1-135-352-11
1-163-267-91
Pending
Description
CERAMIC CHIP 0.1MF 50V
MYLAR 0.1MF 250V
CERAMIC 200pF 3KV
CERAMIC 1500pF 1KV
MYLAR 4300pF 1.8KV
FILM 0.18MF 250V
ELECT 470MF 25V
FILM 0.18MF 250V
MYLAR 0.15MF 250V
MYLAR 0.47MF 250V
FILM 0.18MF 250V
CERAMIC CHIP 0.1MF 50V
MYLAR 0.1MF 100V
MYLAR 0.022MF 100V
MYLAR 0.047MF 100V
ELECT 1MF 50V
CERAMIC CHIP 0.1MF 50V
ELECT 100MF 50V
FILM 1500pF 1KV
CERAMIC 6800pF 1KV
MYLAR 0.1MF 100V
ELECT 100MF 100V
CERAMIC CHIP 0.1MF 50V
ELECT 4.7MF 50V
MYLAR 0.022MF 100V
CERAMIC 1000pF 100V
ELECT 10MF 50V
CERAMIC 56pF 50V
MYLAR 0.056MF 250V
ELECT 220MF 25V
ELECT 220MF 25V
MYLAR 0.01MF 250V
CERAMIC CHIP 470pF 50V
CERAMIC 680pF 50V
Remarks-1
Remarks-2
7146104456
5074104102
510H221193
5101152132
5195432593
5198184583
5156471T25
5198184583
5198154583
5198474583
5198184583
7146104456
5110104111
5116223511
5075473101
5156109T50
7146104456
5156101T50
5190152513
5103682233
5110104111
515X101S01
7146104456
5156479T50
5116223111
5101102112
5156100T50
5121560552
5190563583
5156221T25
5156221T25
5074103102
7183471556
5101681152
Sony
Others
Others
Others
Difference
Sony
Sony
Sony
Others
Sony
Sony
Others
Others
Others
Sony
Others
Sony
HMD-A400(E)
7-9
No.
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
! / * Ref. No.
C555
C556
C557
C558
C559
C560
C561
C562
C563
C564
C565
C566
C567
C570
C571
C572
C573
C574
C575
C576
C577
C579
C580
C581
C583
C584
C585
C586
C587
C588
C590
C591
C592
C593
Part No.
Service
1-137-995-11
1-107-656-11
1-115-339-11
1-137-399-11
1-136-684-51
1-115-339-11
1-163-007-11
1-115-339-11
1-104-661-91
1-104-664-11
Pending
1-137-974-11
Pending
1-126-964-11
1-115-339-11
1-104-664-11
Pending
1-126-970-11
Pending
1-115-339-11
Pending
1-137-413-11
1-137-399-11
1-137-969-11
1-128-561-91
Pending
Pending
1-126-964-11
Pending
1-137-413-11
1-115-339-11
1-115-339-11
1-135-404-11
1-137-378-11
Production
1-137-995-11
1-107-656-91
1-115-339-91
1-137-422-91
1-137-412-91
1-115-339-91
1-163-007-91
1-115-339-91
1-104-661-91
1-104-664-91
Pending
1-137-974-11
Pending
1-126-964-91
1-115-339-91
1-104-660-91
Pending
1-126-970-91
Pending
1-115-339-91
Pending
1-137-413-91
1-137-422-91
1-137-969-11
1-128-561-91
Pending
Pending
1-126-964-91
Pending
1-137-413-91
1-115-339-91
1-115-339-91
1-135-404-11
1-137-378-91
Description
CERAMIC 0.1MF 50V
ELECT 100MF 250V
CERAMIC CHIP 0.1MF 50V
MYLAR 0.1MF 100V
MYLAR 2200pF 100V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 680pF 50V
CERAMIC CHIP 0.1MF 50V
ELECT 330MF 16V
ELECT 47MF 25V
ELECT 3.3MF 250V
FILM 1.6MF 250V
CERAMIC 0.01MF 2KV
ELECT 10MF 50V
CERAMIC CHIP 0.1MF 50V
ELECT 47MF 16V
CERAMIC 0.1MF 50V
ELECT 330MF 50V
CERAMIC CHIP 0.01MF 50V
CERAMIC CHIP 0.1MF 50V
ELECT 22MF 250V
MYLAR 3300pF 100V
MYLAR 0.1MF 100V
FILM 0.22MF 50V
ELECT 33MF 100V
CERAMIC CHIP 270pF 50V
CERAMIC 220pF 1KV
ELECT 10MF 50V
CERAMIC 0.1MF 50V
MYLAR 3300pF 100V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 0.1MF 50V
ELECT 4.7MF 35V
MYLAR 0.22MF 50V
Remarks-1
Remarks-2
5134104452
5156101S03
7146104456
5116104111
5116222111
7146104456
7144681156
7146104456
5156331T16
5156470T25
5156339S03
5198165583
51041034C3
5156100T50
7146104456
5156470T16
5101104152
5156331T50
7146103456
7146104456
5156220S03
5116332111
5075104501
5110224550
515X330T01
7183271556
510H221132
5156100T50
5101104152
5116332111
7146104456
7146104456
5162479T35
5113224150
Sony
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-10
No.
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
! / * Ref. No.
!
!
!
!
!
C594
C595
C597
C599
C601
C602
C603
C604
C606
C607
C608
C609
C610
C611
C612
C613
C614
C615
C616
C618
C619
C620
C622
C623
C625
C626
C628
C630
C634
C639
C640
C645
C646
C648
Part No.
Service
1-137-399-11
1-137-871-11
1-137-378-11
1-126-969-11
Pending
Pending
1-135-380-11
1-135-380-11
1-135-831-11
1-126-949-11
1-137-871-11
1-137-964-11
1-135-351-11
1-163-007-11
Pending
1-163-002-11
1-115-339-11
1-126-933-11
1-115-339-11
1-126-964-11
1-115-339-11
1-135-389-11
Pending
1-163-251-11
1-128-564-11
1-107-656-11
Pending
1-126-942-61
1-126-767-11
1-137-875-11
Pending
1-126-935-11
1-126-942-61
1-137-930-11
Production
1-137-422-91
1-137-871-11
1-137-378-91
1-126-969-91
Pending
Pending
1-135-380-11
1-135-380-11
1-135-831-11
1-126-949-91
1-137-871-11
1-137-964-11
1-135-351-11
1-163-007-91
Pending
1-163-002-91
1-115-339-91
1-126-933-91
1-115-339-91
1-126-964-91
1-115-339-91
1-135-389-11
Pending
1-163-251-91
1-128-564-11
1-107-656-91
Pending
1-126-942-91
1-126-767-91
1-137-875-11
Pending
1-126-935-91
1-126-942-91
1-137-930-11
Description
MYLAR 0.1MF 100V
MYLAR 0.1MF 400V
MYLAR 0.22MF 50V
ELECT 220MF 50V
FILM 0.47MF 250V
FILM 0.68MF 250V
CERAMIC 470pF 250V
CERAMIC 470pF 250V
ELECT 330MF 450V
ELECT 220MF 35V
MYLAR 0.1MF 400V
MYLAR 0.33MF 630V
CERAMIC 4700pF 250V
CERAMIC CHIP 680pF 50V
MYLAR 0.01MF 50V
CERAMIC 270pF 50V
CERAMIC CHIP 0.1MF 50V
ELECT 100MF 16V
CERAMIC CHIP 0.1MF 50V
ELECT 10MF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC 100pF 1KV
CERAMIC CHIP 2200pF 50V
CERAMIC CHIP 100pF 50V
ELECT 220MF 100V
ELECT 100MF 250V
ELECT 2200MF 25V
ELECT 1000MF 25V
ELECT 1000MF 16V
CERAMIC 1000pF 1KV
FILM 0.1MF 250V
ELECT 470MF 16V
ELECT 1000MF 25V
CERAMIC 4700pF 400V
Remarks-1
Remarks-2
5075104501
5074104104
5113224150
5156221T50
5067474425
5067684425
5063471325
5063471325
515P331P45
5156221T35
5074104104
5074334106
5063472425
7144681156
5116103550
7144271156
7146104456
5156101T16
7146104456
5156100T50
7146104456
510H101132
7144222156
7183101556
5156221S01
5156101S03
5153222T25
5156102S25
5156102T16
5101102132
5067104425
5156471T16
5153102S25
5061472440
Sony
Others
Difference
Sony
Sony
Others
Others
Others
Sony
Others
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
HMD-A400(E)
7-11
No.
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
! / * Ref. No.
!
C649
C650
C651
C652
C654
C900
C902
C903
C904
C905
C906
C907
C908
C909
C910
C914
C915
C918
C919
C920
C921
C922
C923
C924
C925
C926
C927
C928
C930
C4001
C4002
C4003
C4005
C4006
Part No.
Service
1-137-930-11
Pending
1-126-942-61
1-137-869-11
1-128-551-11
1-115-339-11
1-126-961-11
1-126-961-11
1-126-961-11
1-126-961-11
1-126-961-11
1-126-964-11
1-115-339-11
1-163-133-00
1-115-339-11
1-163-251-11
1-137-879-11
1-163-243-11
1-163-243-11
1-115-339-11
1-163-235-11
1-163-235-11
1-126-961-11
1-135-395-11
1-115-339-11
1-163-251-11
1-163-251-11
1-115-339-11
1-163-259-91
Pending
1-104-664-11
1-137-399-11
Pending
Pending
Production
1-137-930-11
Pending
1-126-942-91
1-137-869-11
1-104-662-91
1-115-339-91
1-126-961-91
1-126-961-91
1-126-961-91
1-126-961-91
1-126-961-91
1-126-964-91
1-115-339-91
1-163-267-91
1-115-339-91
1-163-251-91
1-137-879-11
1-163-243-91
1-163-243-91
1-115-339-91
1-163-235-91
1-163-235-91
1-126-961-91
1-135-395-11
1-115-339-91
1-163-251-91
1-163-251-91
1-115-339-91
1-163-259-91
Pending
1-104-664-91
1-137-422-91
Pending
Pending
Description
CERAMIC 4700pF 400V
ELECT 330MF 400V
ELECT 1000MF 25V
MYLAR 0.1MF 250V
ELECT 22MF 25V
CERAMIC CHIP 0.1MF 50V
ELECT 2.2MF 50V
ELECT 2.2MF 50V
ELECT 2.2MF 50V
ELECT 2.2MF 50V
ELECT 2.2MF 50V
ELECT 10MF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 470pF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 100pF 50V
CERAMIC 100pF 50V
CERAMIC 47pF 50V
CERAMIC 47pF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 22pF 50V
CERAMIC CHIP 22pF 50V
ELECT 2.2MF 50V
ELECT 4.7MF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 100pF 50V
CERAMIC CHIP 100pF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 220pF 50V
CERAMIC 0.1MF 50V
ELECT 47MF 25V
MYLAR 0.1MF 100V
MYLAR 0.22MF 100V
CERAMIC 0.1MF 50V
Remarks-1
Remarks-2
5061472440
515P331P04
5153102S25
5074104102
5156220T25
7146104456
5156229T50
5156229T50
5156229T50
5156229T50
5156229T50
5156100T50
7146104456
7183471556
7146104456
7183101556
5128101552
7183470556
7183470556
7146104456
7183220556
7183220556
5156229T50
5156479T50
7146104456
7183101556
7183101556
7146104456
7183221556
5101104152
5156470T25
5075104501
5075224505
5101104152
Others
Difference
Sony
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-12
No.
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
! / * Ref. No.
C4007
C4008
C4009
C6000
C6001
C6002
C6003
C6004
C6005
C6006
C6007
C7000
C7001
C7002
C7003
C7004
C7005
C7006
C7007
C7008
C7009
C7010
C7011
C7012
C7013
C7014
C7015
C7016
C7017
C7018
C7019
C7020
C7021
C7022
Part No.
Service
1-137-399-11
1-137-399-11
Pending
1-126-933-11
1-126-967-11
Pending
Pending
1-126-935-11
Pending
1-126-934-11
1-137-928-11
1-135-918-11
1-135-918-11
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
1-163-235-11
1-163-235-11
Pending
1-163-243-11
1-163-243-11
1-163-243-11
1-163-243-11
1-126-924-11
1-115-339-11
1-126-924-11
1-115-339-11
1-163-243-11
1-163-243-11
1-126-924-11
1-115-339-11
1-126-924-11
1-115-339-11
Production
1-137-422-91
1-137-422-91
Pending
1-126-933-91
1-126-967-91
Pending
Pending
1-126-935-91
Pending
1-126-934-91
1-137-928-11
1-135-918-11
1-135-918-11
1-115-339-91
1-115-339-91
1-115-339-91
1-115-339-91
1-163-235-91
1-163-235-91
Pending
1-163-243-91
1-163-243-91
1-163-243-91
1-163-243-91
1-126-924-91
1-115-339-91
1-126-924-91
1-115-339-91
1-163-243-91
1-163-243-91
1-126-924-91
1-115-339-91
1-126-924-91
1-115-339-91
Description
MYLAR 0.1MF 100V
MYLAR 0.1MF 100V
ELECT 100MF 25V
ELECT 100MF 16V
ELECT 47MF 50V
CERAMIC 0.1MF 50V
ELECT 4700MF 16V
ELECT 470MF 16V
MYLAR 0.01MF 50V
ELECT 220MF 16V
CERAMIC 2200pF 1KV
ELECT 220MF 10V
ELECT 220MF 10V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 22pF 50V
CERAMIC CHIP 22pF 50V
ELECT 3.3MF 50V
CERAMIC CHIP 47pF 50V
CERAMIC CHIP 47pF 50V
CERAMIC CHIP 47pF 50V
CERAMIC CHIP 47pF 50V
ELECT 330MF 10V
CERAMIC CHIP 0.1MF 50V
ELECT 330MF 10V
CERAMIC CHIP 0.1MF 50V
CERAMIC CHIP 47pF 50V
CERAMIC CHIP 47pF 50V
ELECT 330MF 10V
CERAMIC CHIP 0.1MF 50V
ELECT 330MF 10V
CERAMIC CHIP 0.1MF 50V
Remarks-1
Remarks-2
5075104501
5075104501
5156101T25
5156101T16
5156470T50
5101104152
5156472S16
5153471T16
5074103505
5156221S16
510H222138
5152221T10
5152221T10
7146104456
7146104456
7146104456
7146104456
7183220556
7183220556
5152339T50
7183470556
7183470556
7183470556
7183470556
5156331T10
7146104456
5156331T10
7146104456
7183470556
7183470556
5156331T10
7146104456
5156331T10
7146104456
Sony
Sony
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-13
No.
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CAPACITOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
CONNECTOR
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
! / * Ref. No.
C7023
C7024
C7025
C7026
C7027
C7028
C7030
CN601
CN602
CN604
CN903
CN7000
P7000
P7001
P7002
P7003
P7004
D402
D501
D502
D503
D504
D506
D507
D508
D509
D510
D511
D512
D513
D514
D515
D516
D517
Part No.
Service
1-163-243-11
1-163-243-11
1-135-393-11
1-135-393-11
1-135-393-11
1-135-393-11
Pending
1-251-444-11
1-815-267-11
1-793-920-11
Pending
1-695-915-11
1-815-478-11
1-815-477-11
1-815-477-11
1-815-477-11
1-815-477-11
8-719-200-02
8-719-070-90
8-719-110-39
Pending
8-719-070-90
8-719-070-90
Pending
Pending
8-719-083-88
8-719-070-90
Pending
Pending
8-719-074-13
8-719-074-25
8-719-074-13
8-719-070-90
8-719-070-90
Production
1-163-243-91
1-163-243-91
1-135-393-11
1-135-393-11
1-135-393-11
1-135-393-11
Pending
1-251-444-11
1-815-267-11
1-793-920-11
Pending
1-695-915-11
1-815-478-11
1-815-477-11
1-815-477-11
1-815-477-11
1-815-477-11
8-719-904-02
8-719-070-90
8-719-921-91
Pending
8-719-070-90
8-719-070-90
Pending
Pending
8-719-083-88
8-719-070-90
Pending
Pending
8-719-074-13
8-719-074-25
8-719-074-13
8-719-070-90
8-719-070-90
Description
CERAMIC CHIP 47pF 50V
CERAMIC CHIP 47pF 50V
ELECT 100MF 10V
ELECT 100MF 10V
ELECT 100MF 10V
ELECT 100MF 10V
CERAMIC CHIP 0.01MF 50V
AC SOCKET
PLUG, CONNECTOR 2P
PIN, CONNECTOR 3P
4P
TAB (CONTACT)
CONNECTOR, USB (B)
CONNECTOR, USB (A)
CONNECTOR, USB (A)
CONNECTOR, USB (A)
CONNECTOR, USB (A)
DIODE 10E2
DIODE 1N4148
ZENER DIODE RD15ES-B1
DIODE 31DF4
DIODE 1N4148
DIODE 1N4148
DIODE SB140
DIODE DD84RCLS-SONY-YCC11
DIODE PS104R
DIODE 1N4148
DIODE ER206
DIODE ER206
DIODE BYV26C
DIODE PG104R
DIODE BYV26C
DIODE 1N4148
DIODE 1N4148
Remarks-1
Remarks-2
7183470556
7183470556
5156101T10
5156101T10
5156101T10
5156101T10
7146103456
4570707C00
4490301100
4490300190
4490400200
4490100209
4490400343
4490400342
4490400342
4490400342
4490400342
4120104002
412914148U
41205015AU
41303031F4
412914148U
412914148U
4130104140
4130800840
4130101040
412914148U
413020206U
413020206U
413010426C
4130101041
413010426C
412914148U
412914148U
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
Difference
Sony
Sony
Sony
Others
Sony
Sony
Others
Others
Others
HMD-A400(E)
7-14
No.
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
! / * Ref. No.
!
D518
D519
D520
D521
D522
D523
D524
D525
D526
D527
D528
D529
D530
D531
D532
D533
D534
D535
D537
D538
D540
D592
D601
D605
D606
D607
D608
D609
D610
D611
D613
D615
D616
D617
Part No.
Service
8-719-070-90
8-719-083-88
8-719-070-90
Pending
8-719-074-25
8-719-070-90
8-719-070-90
8-719-995-63
8-719-070-90
8-719-110-35
8-719-074-16
8-719-070-90
8-719-070-90
8-719-070-90
8-719-077-81
8-719-070-90
8-719-070-90
8-719-070-90
8-719-074-16
8-719-110-39
8-719-070-90
8-719-070-90
8-719-510-63
8-719-053-19
8-719-070-90
8-719-154-15
8-719-154-15
8-719-070-90
8-719-070-90
8-719-070-90
Pending
8-719-077-80
Pending
8-719-074-19
Production
8-719-070-90
8-719-083-88
8-719-070-90
Pending
8-719-074-25
8-719-070-90
8-719-070-90
8-719-995-63
8-719-070-90
8-719-900-36
8-719-074-16
8-719-070-90
8-719-070-90
8-719-070-90
8-719-077-81
8-719-070-90
8-719-070-90
8-719-070-90
8-719-074-16
8-719-921-91
8-719-070-90
8-719-070-90
8-719-510-63
8-719-053-19
8-719-070-90
8-719-154-15
8-719-154-15
8-719-070-90
8-719-070-90
8-719-070-90
Pending
8-719-077-80
Pending
8-719-074-19
Description
DIODE 1N4148
DIODE PS104R
DIODE 1N4148
DIODE 31DF4
DIODE PG104R
DIODE 1N4148
DIODE 1N4148
ZENER DIODE HZ6C3
DIODE 1N4148
ZENER DIODE RD13ES-B1
DIODE RGP02-18
DIODE 1N4148
DIODE 1N4148
DIODE 1N4148
ZENER DIODE 1M160Z
DIODE 1N4148
DIODE 1N4148
DIODE 1N4148
DIODE RGP02-18
ZENER DIODE RD15ES-B1
DIODE 1N4148
DIODE 1N4148
DIODE D4SB60L-F
DIODE UF4007G23
DIODE 1N4148
ZENER DIODE RD27EB4
ZENER DIODE RD27EB4
DIODE 1N4148
DIODE 1N4148
DIODE 1N4148
DIODE ER206
DIODE UF5404G
DIODE 31DF2
DIODE UF5402G
Remarks-1
412914148U
4130101040
412014148T
41303031F4
4130101041
412914148U
412914148U
41205006C3
412914148U
4120501202
4130100218
412914148U
412914148U
412014148T
4120510160
412914148U
412014148T
412914148U
4130100218
41205015AU
412914148U
412914148U
4130400600
4130104007
412914148U
4120502705
4120502705
412914148U
412914148U
412914148U
413020206U
4130305404
41303031F2
4130305402
Remarks-2
Difference
Others
Others
Others
Sony
Others
Others
Others
Others
Others
Sony
Sony
Sony
Sony
Sony
Others
Others
HMD-A400(E)
7-15
No.
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
FUSE
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
! / * Ref. No.
!
D619
D628
D629
D630
D631
D632
D901
D902
D903
D904
D905
D906
D907
D908
D910
D911
D4001
D4002
D6000
D6001
D6002
D6003
D6005
D7000
ZD6001
F601
FB501
FB502
FB504
FB507
FB508
FB601
FB602
FB605
Part No.
Service
8-719-070-90
Pending
8-719-070-90
8-719-070-90
8-719-077-80
8-719-070-90
8-719-921-42
8-719-921-42
8-719-921-42
8-719-921-42
8-719-921-42
8-719-921-42
8-719-070-90
8-719-070-90
8-719-070-90
8-719-070-90
Pending
Pending
8-719-070-90
8-719-074-13
8-719-083-88
8-719-083-88
Pending
8-719-921-42
8-719-927-42
1-576-231-11
1-469-402-11
1-424-740-11
1-469-402-11
Pending
Pending
1-469-402-11
1-469-401-11
1-535-303-31
Production
8-719-070-90
Pending
8-719-070-90
8-719-070-90
8-719-077-80
8-719-070-90
8-719-921-42
8-719-921-42
8-719-921-42
8-719-921-42
8-719-921-42
8-719-921-42
8-719-070-90
8-719-070-90
8-719-070-90
8-719-070-90
Pending
Pending
8-719-070-90
8-719-074-13
8-719-083-88
8-719-083-88
Pending
8-719-921-42
8-719-927-42
1-576-231-11
1-469-402-11
1-424-740-11
1-469-402-11
Pending
Pending
1-469-402-11
1-469-401-11
1-535-143-11
Description
Remarks-1
DIODE 1N4148
DIODE ER206
DIODE 1N4148
DIODE 1N4148
DIODE UF5404G
DIODE 1N4148
ZENER DIODE MTZJ-5.1A
ZENER DIODE MTZJ-5.1A
ZENER DIODE MTZJ-5.1A
ZENER DIODE MTZJ-5.1A
ZENER DIODE MTZJ-5.1A
ZENER DIODE MTZJ-5.1A
DIODE 1N4148
DIODE 1N4148
DIODE 1N4148
DIODE 1N4148
ZENER DIODE HZ18-2
ZENER DIODE HZ18-2
DIODE 1N4148
DIODE BYV26C
DIODE PS104R
DIODE PS104R
DIODE F10P06Q
ZENER DIODE MTZJ-5.1A
ZENER DIODE HZ27-2
FUSE (H.B.C.) (4A/250V)
INDUCTOR 3UH
COIL, CHOKE 5.2UH
INDUCTOR 3UH
COIL, CHOKE 10UH
COIL, CHOKE 10UH
INDUCTOR 3UH
INDUCTOR 2.8UH
JUMP WIRE 0.6_
412914148U
413020206U
412914148U
412914148U
4130305404
412914148U
41205051AU
41205051AU
41205051AU
41205051AU
41205051AU
41205051AU
412914148U
412914148U
412914148U
412914148U
4120501802
4120501802
412914148U
413010426C
4130101040
4130101040
4131010P06
41205051AU
4120502702
5268400052
4322309006
7069R00509
4322309006
4323100303
4323100303
4322309006
4322309504
5406100000
Remarks-2
Difference
Sony
Others
Others
Others
Others
Sony
Others
Others
Sony
Sony
Others
Others
Sony
HMD-A400(E)
7-16
No.
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
FERRITE BEAD
IC
IC
IC
IC
IC
IC
IC
IC
IC
! / * Ref. No.
FB606
FB607
FB608
FB609
FB612
FB613
FB617
FB618
FB619
FB621
FB622
FB901
FB7001
FB7002
FB7003
FB7004
FB7005
FB7006
FB7007
FB7008
FB7009
FB7010
FB7011
FB7012
FB7013
IC401
IC501
IC502
IC504
IC601
IC602
IC603
IC606
IC607
Part No.
Service
1-469-401-11
1-469-401-11
1-469-401-11
1-469-402-11
Pending
Pending
1-469-401-11
1-469-611-11
1-469-403-11
1-469-401-11
1-469-401-11
1-469-611-11
1-469-401-11
1-469-401-11
1-469-401-11
1-469-401-11
1-469-403-11
1-469-403-11
Pending
1-469-403-11
Pending
1-469-403-11
1-469-403-11
1-469-403-11
1-469-403-11
8-759-593-28
6-700-470-01
6-700-467-01
8-759-008-70
8-759-582-09
8-749-016-36
8-759-466-12
8-729-048-22
8-759-279-76
Production
1-469-401-11
1-469-401-11
1-469-401-11
1-469-402-11
Pending
Pending
1-469-401-11
1-469-611-11
1-469-403-11
1-469-401-11
1-469-401-11
1-469-611-11
1-469-401-11
1-469-401-11
1-469-401-11
1-469-401-11
1-469-403-11
1-469-403-11
Pending
1-469-403-11
Pending
1-469-403-11
1-469-403-11
1-469-403-11
1-469-403-11
8-759-593-28
6-700-470-01
6-700-467-01
8-759-991-16
8-759-582-09
8-749-016-36
8-759-466-12
8-729-048-22
8-759-279-76
Description
INDUCTOR 2.8UH
INDUCTOR 2.8UH
INDUCTOR 2.8UH
INDUCTOR 3UH
COIL, CHOKE 600UH
COIL, CHOKE 600UH
INDUCTOR 2.8UH
INDUCTOR 2UH
FERRITE
INDUCTOR 2.8UH
INDUCTOR 2.8UH
INDUCTOR 2UH
INDUCTOR 2.8UH
INDUCTOR 2.8UH
INDUCTOR 2.8UH
INDUCTOR 2.8UH
FERRITE
FERRITE
FERRITE 2.3UH
FERRITE
FERRITE 2.3UH
FERRITE
FERRITE
FERRITE
FERRITE
IC LA78040
IC TDA4841
IC KA3843A
IC LM358N
IC UC3842A
IC TLP6214-Y-LF2
IC TL431ACLP
TRANSISTOR MCR100
IC MCT7812CT
Remarks-1
Remarks-2
4322309504
4322309504
4322309504
4322309006
7069R00601
7069R00601
4322309504
4322209005
4322209046
4322309504
4322309504
4322209005
4322309504
4322309504
4322309504
4322309504
4322209046
4322209046
7099159250
4322209046
7099159250
4322209046
4322209046
4322209046
4322209046
4159780400
4159484100
4159384300
4159358000
4159384200
4159621000
415943100A
4114501006
4159781201
Others
Others
Others
Others
Difference
Others
Others
Others
Others
Others
Others
Others
Others
Others
Sony
Sony
Others
Others
Sony
Others
Sony
Others
Others
Sony
HMD-A400(E)
7-17
No.
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
IC
IC
IC
IC
IC
IC
IC
IC
IC
IC
IC
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
! / * Ref. No.
IC901
IC902
IC903
IC4001
IC4002
IC6000
IC6001
IC7000
IC7001
IC7002
IC7003
JW105
JW106
JW126
JW138
JW231
JW246
L501
L502
L503
L504
L505
L506
L507
L508
L509
L601
L602
L603
L604
L605
L607
L609
L6000
Part No.
Service
6-800-348-01
8-759-650-44
8-759-605-05
Pending
8-759-008-70
Pending
Pending
Pending
Pending
Pending
8-759-605-05
1-469-401-11
1-469-402-11
1-469-401-11
1-469-403-11
1-469-403-11
1-469-403-11
1-412-550-11
1-469-994-11
Pending
Pending
1-424-738-11
Pending
1-412-537-31
Pending
1-469-995-11
1-412-537-31
1-412-537-31
1-412-537-31
1-412-537-31
1-412-537-31
1-410-645-31
1-412-537-31
1-424-739-11
Production
6-800-348-01
8-759-650-44
8-759-605-05
Pending
8-759-991-16
Pending
Pending
Pending
Pending
Pending
8-759-605-05
1-469-401-11
1-469-402-11
1-469-401-11
1-469-403-11
1-469-403-11
1-469-403-11
1-412-550-25
1-469-994-11
Pending
Pending
1-424-738-11
Pending
1-412-537-25
Pending
1-469-995-11
1-412-537-25
1-412-537-25
1-412-537-25
1-412-537-25
1-412-537-25
1-410-645-41
1-412-537-25
1-424-739-11
Description
IC ST72T754J9B1
IC M24C16BN6
IC M51951BSL
IC M62393P
IC LM358N
TRANSISTOR TOP223Y
IC LM431
IC ISP1122A
IC RYC8220-2P
IC RYC8220-2P
IC M51951BSL
INDUCTOR 2.8UH
INDUCTOR 3UH
INDUCTOR 2.8UH
FERRITE
FERRITE
FERRITE
INDUCTOR 1.2mH
INDUCTOR 100UH
COIL, CHOKE 10mH
COIL, CHOKE 32UH
COIL, LINEARITY
COIL, CHOKE 10mH
INDUCTOR 100UH
FUSIBLE 0.12 1/2W
PEAKING COIL 150UH
INDUCTOR 100UH
INDUCTOR 100UH
INDUCTOR 100UH
INDUCTOR 100UH
INDUCTOR 100UH
INDUCTOR 100UH
INDUCTOR 100UH
COIL, CHOKE 5.2UH
Remarks-1
Remarks-2
4159727540
415924C160
4159519510
4159623930
4159358000
4100502230
415943100A
4159112210
4159822000
4159822000
4159519510
4322309504
4322309006
4322309504
4322209046
4322209046
4322209046
4323122003
4321101006
4323103003
4323320003
708S219R00
4323103003
4323101303
41802128A6
4321151006
4323101303
4323101303
4323101303
4323101303
4323101303
4323101303
4323101303
4323529303
Others
Others
Sony
Difference
Sony
Others
Sony
Others
Others
Others
Sony
Others
Sony
Sony
Sony
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-18
No.
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
COIL
FILTER
PHOTO COUPLER
PHOTO COUPLER
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
! / * Ref. No.
!
L6001
L7001
L7002
L7003
L7007
L7008
L7009
L7010
L7012
L7013
L7014
L7015
L7016
L7017
L7018
L7019
L7020
L7025
L7028
L7029
L7030
L7033
L7034
L7035
LF601
PH6000
PH6001
Q401
Q501
Q502
Q503
Q504
Q505
Q506
Part No.
Service
1-412-537-31
Pending
Pending
1-469-807-11
1-412-911-11
1-412-911-11
1-469-807-11
1-469-807-11
1-469-807-11
1-469-807-11
1-412-911-11
1-469-807-11
1-469-807-11
1-469-807-11
1-469-807-11
1-412-911-11
1-412-911-11
1-412-911-11
1-412-911-11
1-412-911-11
1-412-911-11
1-412-911-11
1-412-911-11
1-412-911-11
1-424-741-11
Pending
Pending
8-729-194-57
8-729-056-48
8-729-042-34
Pending
8-729-194-57
8-729-194-57
8-729-906-93
Production
1-412-537-25
Pending
Pending
1-469-807-11
1-412-911-21
1-412-911-21
1-469-807-11
1-469-807-11
1-469-807-11
1-469-807-11
1-412-911-21
1-469-807-11
1-469-807-11
1-469-807-11
1-469-807-11
1-412-911-21
1-412-911-21
1-412-911-21
1-412-911-21
1-412-911-21
1-412-911-21
1-412-911-21
1-412-911-21
1-412-911-21
1-424-741-11
Pending
Pending
8-729-191-57
8-729-056-48
8-729-043-53
Pending
8-729-191-57
8-729-191-57
8-729-906-93
Description
INDUCTOR 100UH
FERRITE 0.45UH
FERRITE 0.45UH
INDUCTOR
FERRITE 1.1UH
FERRITE 1.1UH
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
FERRITE 1.1UH
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
FERRITE 1.1UH
FERRITE 1.1UH
FERRITE 1.1UH
FERRITE 1.1UH
FERRITE 1.1UH
FERRITE 1.1UH
FERRITE 1.1UH
FERRITE 1.1UH
FERRITE 1.1UH
COIL, CHOKE 13mH
IC TLP621-YLF2
IC TLP621-YLF2
TRANSISTOR 2SC945-P
TRANSISTOR SFS9634
TRANSISTOR IRFU110A
TRANSISTOR 2SC5445
TRANSISTOR 2SC945-P
TRANSISTOR 2SC945-P
TRANSISTOR IRF640
Remarks-1
Remarks-2
4323101303
7099458250
7099458250
4322502006
7099159250
7099159250
4322502006
4322502006
4322502006
4322502006
7099159250
4322502006
4322502006
4322502006
4322502006
7099159250
7099159250
7099159250
7099159250
7099159250
7099159250
7099159250
7099159250
7099159250
7069R00133
4159621000
4159621000
411020945P
4107496340
4103801100
4100254450
411020945P
411020945P
4105906400
Sony
Sony
Sony
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
Sony
Sony
Sony
Sony
HMD-A400(E)
7-19
No.
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
! / * Ref. No.
Q508
Q510
Q511
Q512
Q513
Q514
Q515
Q516
Q517
Q518
Q519
Q520
Q521
Q522
Q523
Q524
Q525
Q526
Q527
Q528
Q529
Q530
Q531
Q532
Q533
Q534
Q535
Q536
Q537
Q538
Q539
Q540
Q541
Q542
Part No.
Service
8-729-194-57
8-729-141-03
8-729-056-44
8-729-029-86
8-729-141-03
Pending
8-729-194-57
8-729-141-03
8-729-306-92
Pending
8-729-119-80
8-729-194-57
8-729-141-03
8-729-048-61
Pending
8-729-906-93
8-729-141-03
8-729-029-86
8-729-194-57
8-729-194-57
8-729-194-57
8-729-119-80
8-729-051-31
8-729-141-03
8-729-141-03
8-729-194-57
8-729-029-86
8-729-906-93
8-729-194-57
8-729-194-57
8-729-194-57
8-729-194-57
8-729-056-44
8-729-122-12
Production
8-729-191-57
8-729-141-04
8-729-056-44
8-729-806-34
8-729-141-04
Pending
8-729-191-57
8-729-141-04
8-729-306-92
Pending
8-729-119-80
8-729-191-57
8-729-141-04
8-729-048-61
Pending
8-729-906-93
8-729-141-04
8-729-806-34
8-729-191-57
8-729-191-57
8-729-191-57
8-729-119-80
8-729-051-31
8-729-141-04
8-729-141-04
8-729-191-57
8-729-806-34
8-729-906-93
8-729-191-57
8-729-191-57
8-729-191-57
8-729-191-57
8-729-056-44
8-729-300-72
Description
TRANSISTOR 2SC945-P
TRANSISTOR 2SA733-QP
TRANSISTOR H2N6718L
TRANSISTOR DTC124ESA
TRANSISTOR 2SA733-QP
TRANSISTOR 2SC2362-KG
TRANSISTOR 2SC945-P
TRANSISTOR 2SA733-QP
TRANSISTOR 2SD669AVC
TRANSISTOR HSB649A
TRANSISTOR 2SC2688-LK
TRANSISTOR 2SC945-P
TRANSISTOR 2SA733-QP
TRANSISTOR 2SK2843LB2SONY
TRANSISTOR 2SD1640Q
TRANSISTOR IRF640
TRANSISTOR 2SA733-QP
TRANSISTOR DTC124ESA
TRANSISTOR 2SC945-P
TRANSISTOR 2SC945-P
TRANSISTOR 2SC945-P
TRANSISTOR 2SC2688-LK
TRANSISTOR KSP92
TRANSISTOR 2SA733-QP
TRANSISTOR 2SA733-QP
TRANSISTOR 2SC945-P
TRANSISTOR DTC124ESA
TRANSISTOR IRF640
TRANSISTOR 2SC945-P
TRANSISTOR 2SC945-P
TRANSISTOR 2SC945-P
TRANSISTOR 2SC945-P
TRANSISTOR H2N6718L
TRANSISTOR 2SA1221-L
Remarks-1
Remarks-2
411020945P
4110007330
4111167180
4110234000
4110007330
411022362G
411020945P
4110007330
410030669A
410010649A
4100226880
411020945P
4110007330
4101528430
4100316400
4105906400
4110007330
4110234000
411020945P
411020945P
411020945P
4100226880
4112409200
4110007330
4110007330
411020945P
4110234000
4105906400
411020945P
411020945P
411020945P
411020945P
4111167180
411010647A
Sony
Sony
Others
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
Sony
HMD-A400(E)
7-20
No.
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
! / * Ref. No.
Q543
Q544
Q545
Q546
Q547
Q548
Q549
Q601
Q602
Q607
Q608
Q615
Q902
Q4001
Q4002
Q4003
Q4004
Q6000
R401
R402
R403
R404
R406
R407
R408
R409
R410
R411
R412
R500
R501
R502
R503
R504
Part No.
Service
Pending
Pending
8-729-056-44
8-729-122-12
8-729-194-57
8-729-141-03
8-729-029-86
8-729-141-03
8-729-048-61
8-729-200-36
8-729-029-86
8-729-194-57
8-729-139-04
8-729-306-92
Pending
8-729-306-92
Pending
Pending
Pending
Pending
Pending
1-244-254-11
1-249-383-11
Pending
1-260-105-11
1-216-060-91
Pending
Pending
Pending
1-247-798-11
1-216-083-00
1-227-372-11
1-216-065-11
1-227-379-11
Production
Pending
Pending
8-729-056-44
8-729-300-72
8-729-191-57
8-729-141-04
8-729-206-21
8-729-141-04
8-729-048-61
8-729-200-36
8-729-806-34
8-729-191-57
8-729-139-04
8-729-306-92
Pending
8-729-306-92
Pending
Pending
Pending
Pending
Pending
1-244-254-11
1-247-999-91
Pending
1-260-105-91
1-216-060-91
Pending
Pending
Pending
1-247-798-91
1-216-083-91
1-227-372-11
1-216-065-91
1-227-379-11
Description
TRANSISTOR 2SC3421
TRANSISTOR 2SA1358
TRANSISTOR H2N6718L
TRANSISTOR 2SA1221-L
TRANSISTOR 2SC945-P
TRANSISTOR 2SA733-QP
TRANSISTOR DTC124ESA
TRANSISTOR 2SA733-QP
TRANSISTOR 2SK2843LB2SONY
TRANSISTOR 2SA966-Y
TRANSISTOR DTC124ESA
TRANSISTOR 2SC945-P
TRANSISTOR 2N3904
TRANSISTOR 2SD669AVC
TRANSISTOR HSB649A
TRANSISTOR 2SD669AVC
TRANSISTOR HSB649A
TRANSISTOR RN1001
METAL CHIP 2.15K 1/10W
METAL CHIP 2.1K 1/10W
METAL OXIDE 1 1W
METAL OXIDE 0.75 2W
CARBON 1.5 1/4W
CARBON 330 1W
CARBON 3.3K 1/2W
RES-CHIP 3K 1/10W
METAL OXIDE 1.5 1W
METAL 6.8K 1/4W
CARBON 6.8K 1/4W
CARBON 43 1/4W
RES-CHIP 27K 1/10W
METAL CHIP 22.1K 1/10W
RES-CHIP 4.7K 1/10W
METAL CHIP 732 1/10W
Remarks-1
4100234210
4100013580
4111167180
411010647A
411020945P
4110007330
4110234000
4110007330
4101528430
4110009660
4110234000
411020945P
4111139040
410030669A
410010649A
410030669A
410010649A
4116610010
419A121512
419A121012
4177110956
4172075856
4050515955
417713315B
4050133255
4010130252
4177115956
4050568255
4050568255
4050543055
TS29050844
419A122122
4010147252
419A173202
Remarks-2
Difference
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
Sony
Sony
Others
Sony
Others
HMD-A400(E)
7-21
No.
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
! / * Ref. No.
R505
R506
R507
R508
R509
R510
R511
R512
R513
R515
R516
R517
R518
R519
R520
R521
R522
R523
R524
R525
R526
R527
R528
R529
R530
R531
R532
R533
R534
R535
R536
R537
R538
R539
Part No.
Service
Pending
1-216-073-00
1-216-073-00
1-247-786-11
1-247-844-11
1-216-025-11
1-216-025-11
1-216-198-11
1-216-025-11
1-227-381-11
1-247-846-11
1-216-073-00
1-216-114-00
1-244-258-11
1-244-188-11
Pending
1-216-065-11
1-216-073-00
1-216-071-00
Pending
1-216-065-11
1-216-073-00
Pending
1-249-417-11
1-244-275-11
1-216-065-11
1-260-083-11
1-244-262-11
1-244-255-11
Pending
Pending
1-260-113-11
1-216-065-11
1-216-073-00
Production
Pending
1-216-073-91
1-216-073-91
1-247-786-91
1-247-844-91
1-216-025-91
1-216-025-91
1-216-198-91
1-216-025-91
1-227-381-11
1-247-846-91
1-216-073-91
1-216-114-91
1-244-258-11
1-244-188-11
Pending
1-216-065-91
1-216-073-91
1-216-071-91
Pending
1-216-065-91
1-216-073-91
Pending
1-247-831-91
1-244-275-11
1-216-065-91
1-260-083-91
1-244-262-11
1-244-255-11
Pending
Pending
1-260-113-91
1-216-065-91
1-216-073-91
Description
Remarks-1
RES-CHIP 2.8K 1/10W
RES-CHIP 10K 1/10W
RES-CHIP 10K 1/10W
CARBON 13 1/4W
CARBON 3.6K 1/4W
RES-CHIP 100 1/10W
RES-CHIP 100 1/10W
RES-CHIP 1K 1/8W
RES-CHIP 100 1/10W
METAL CHIP 78.7K 1/10W
CARBON 4.3K 1/4W
RES-CHIP 10K 1/10W
RES-CHIP 510K 1/10W
METAL OXIDE 100 2W
METAL OXIDE 0.22 2W
METAL 5.23K 1/4W
RES-CHIP 4.7K 1/10W
RES-CHIP 10K 1/10W
RES-CHIP 8.2K 1/10W
CARBON 120 1/4W
RES-CHIP 4.7K 1/10W
RES-CHIP 10K 1/10W
CARBON 120 1/2W
CARBON 1K 1/4W
METAL OXIDE 1.3 2W
RES-CHIP 4.7K 1/10W
CARBON 47 1/2W
METAL OXIDE 1.3K 1W
METAL OXIDE 2.7 2W
METAL OXIDE 1K 2W
METAL OXIDE 1.1K 2W
CARBON 15K 1/2W
RES-CHIP 4.7K 1/10W
RES-CHIP 10K 1/10W
4010128202
4010110352
4010110352
4050513355
4050536255
4010110152
4010110152
4010810252
4010110152
419A178722
4050543255
4010110352
4010151452
4172010153
4171022853
4257045231
4010147252
4010110352
4010182252
4050512155
4010147252
4010110352
4050112155
4050510255
417721395A
4010147252
4050147055
4171013255
4172027953
4177210255
4177211255
4050115355
4010147252
4010110352
Remarks-2
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-22
No.
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
! / * Ref. No.
R540
R543
R544
R545
R547
R549
R551
R552
R553
R554
R555
R556
R557
R558
R559
R560
R561
R564
R565
R566
R567
R568
R569
R570
R571
R572
R573
R574
R575
R576
R577
R578
R579
R580
Part No.
Service
1-260-135-11
1-244-266-11
1-260-123-11
1-260-123-11
1-249-425-11
1-216-073-00
1-227-380-11
1-216-097-11
1-249-441-11
1-216-154-00
Pending
1-216-073-00
1-244-255-11
1-249-429-11
1-249-417-11
1-216-101-00
1-249-437-11
1-216-105-91
Pending
1-249-429-11
1-216-073-00
1-249-429-11
1-260-097-11
1-216-057-00
1-249-425-11
1-249-393-11
1-247-868-11
1-249-431-11
1-216-060-91
Pending
Pending
1-249-417-11
1-216-057-00
1-216-025-11
Production
1-260-135-91
1-244-266-11
1-260-123-91
1-260-123-91
1-247-847-91
1-216-073-91
1-227-380-11
1-216-097-91
1-247-879-91
1-216-154-91
Pending
1-216-073-91
1-244-255-11
1-247-855-91
1-247-831-91
1-216-101-91
1-247-871-91
1-216-105-91
Pending
1-247-855-91
1-216-073-91
1-247-855-91
1-260-097-91
1-216-057-91
1-247-847-91
1-247-783-91
1-247-868-91
1-247-859-91
1-216-060-91
Pending
Pending
1-247-831-91
1-216-057-91
1-216-025-91
Description
Remarks-1
Remarks-2
CARBON 1M 1/2W
METAL OXIDE 270 1W
CARBON 100K 1/2W
CARBON 100K 1/2W
CARBON 4.7K 1/4W
RES-CHIP 10K 1/10W
METAL CHIP 7.32K 1/10W
RES-CHIP 100K 1/10W
CARBON 100K 1/4W
RES-CHIP 15 1/8W
CARBON 180 1/4W
RES-CHIP 10K 1/10W
METAL OXIDE 2.7 2W
CARBON 10K 1/4W
CARBON 1K 1/4W
RES-CHIP 150K 1/10W
CARBON 47K 1/4W
RES-CHIP 220K 1/10W
CARBON 200 1/4W
CARBON 10K 1/4W
RES-CHIP 10K 1/10W
CARBON 10K 1/4W
CARBON 680 1/2W
RES-CHIP 2.2K 1/10W
CARBON 4.7K 1/4W
CARBON 10 1/4W
CARBON 36K 1/4W
CARBON 15K 1/4W
RES-CHIP 3K 1/10W
METAL OXIDE 51K 2W
CARBON 120 1/4W
CARBON 1K 1/4W
RES-CHIP 2.2K 1/10W
RES-CHIP 100 1/10W
4050110555
4177127153
4050110455
4050110455
4050547255
4010110352
419A173212
4010110452
4050510455
4010815052
4050518155
4010110352
4172027953
4050510355
4050510255
4010115452
4050547355
4010122452
4050520155
4050510355
4010110352
4050510355
4050168155
TS29051467
4050547255
4050510055
4050536355
4050515355
4010130252
4172051355
4050512155
4050510255
TS29051467
4010110152
Sony
Others
Sony
Sony
Sony
Sony
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-23
No.
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
! / * Ref. No.
!
R582
R583
R584
R585
R586
R589
R590
R591
R592
R594
R595
R596
R597
R598
R599
R601
R605
R609
R610
R611
R612
R614
R615
R616
R618
R619
R620
R621
R622
R623
R624
R625
R626
R627
Part No.
Service
1-249-424-11
1-244-275-11
1-216-067-00
1-216-066-00
Pending
1-240-902-11
1-247-903-00
1-216-067-00
1-216-089-11
1-216-099-00
1-216-065-11
Pending
Pending
Pending
Pending
1-260-132-91
1-227-382-11
1-216-059-00
1-216-001-00
1-216-609-11
1-227-377-11
1-244-192-11
1-244-176-11
Pending
1-216-073-00
1-216-073-00
1-216-049-11
1-216-182-00
1-216-182-00
1-216-025-11
Pending
1-216-073-00
1-216-073-00
Pending
Production
1-247-845-91
1-244-275-11
1-216-067-91
1-216-066-91
Pending
1-240-902-11
1-247-903-91
1-216-067-91
1-216-089-91
1-216-099-91
1-216-065-91
Pending
Pending
Pending
Pending
1-260-132-91
1-227-382-11
1-216-059-91
1-216-001-11
1-216-007-91
1-227-377-11
1-244-192-11
1-244-176-11
Pending
1-216-073-91
1-216-073-91
1-216-049-91
1-216-182-91
1-216-182-91
1-216-025-91
Pending
1-216-073-91
1-216-073-91
Pending
Description
Remarks-1
CARBON 3,9K 1/4W
METAL OXIDE 1.3 2W
RES-CHIP 5.6K 1/10W
RES-CHIP 5.1K 1/10W
METAL 124K 1/4W
METAL 10K 1/4W
CARBON 1M 1/4W
RES-CHIP 5.6K 1/10W
RES-CHIP 47K 1/10W
RES-CHIP 120K 1/10W
RES-CHIP 4.7K 1/10W
METAL CHIP 95.3K 1/10W
METAL OXIDE 36 1W
METAL 34.1K 1/4W
METAL CHIP 2.61K 1/10W
CARBON 560K 1/2W
METAL OXIDE 75K 2W
RES-CHIP 2.7K 1/10W
RES-CHIP 10 1/10W
RES-CHIP 18 1/10W
METAL CHIP 4.99K 1/10W
METAL OXIDE 0.22 2W
METAL 1.82K 1/4W
METAL 3.32K 1/4W
RES-CHIP 10K 1/10W
RES-CHIP 10K 1/10W
RES-CHIP 1K 1/10W
RES-CHIP 220 1/8W
RES-CHIP 220 1/8W
RES-CHIP 100 1/10W
RES-CHIP 9.1K 1/10W
RES-CHIP 10K 1/10W
RES-CHIP 10K 1/10W
RES-CHIP 1K 1/10W
4050539255
417721395A
4010156252
4010151252
4257041243
4257041002
4050510555
4010156252
4010147352
4010112452
4010147252
419A195322
4177136053
4257043412
419A126112
4050156455
4172075353
4010127252
4010110052
4010118052
419A149912
4172022855
4257041821
4257043321
4010110352
4010110352
4010110252
4010822152
4010822152
4010110152
4010191252
4010110352
4010110352
4010110202
Remarks-2
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Others
Sony
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-24
No.
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
! / * Ref. No.
R628
R629
R630
R640
R641
R642
R643
R644
R652
R653
R655
R656
R669
R670
R675
R677
R678
R900
R902
R903
R904
R905
R906
R907
R908
R909
R911
R912
R913
R914
R915
R918
R919
R920
Part No.
Service
1-247-802-11
1-216-049-11
1-216-063-91
1-249-413-11
1-216-041-00
1-249-409-11
1-244-185-11
1-240-894-11
1-247-807-31
1-244-195-11
1-216-061-00
1-249-429-11
1-244-278-11
1-259-878-11
1-244-183-11
1-216-121-11
1-259-878-11
Pending
1-249-417-11
1-249-417-11
1-247-807-31
1-249-417-11
1-249-417-11
1-249-417-11
1-216-073-00
1-249-417-11
1-249-417-11
1-216-222-00
1-249-417-11
1-244-247-11
1-240-907-11
1-216-073-00
1-249-425-11
1-216-073-00
Production
1-247-802-91
1-216-049-91
1-216-063-91
1-247-823-91
1-216-041-91
1-247-815-91
1-244-185-11
1-240-894-11
1-247-807-91
1-244-195-11
1-216-061-91
1-247-855-91
1-244-278-11
1-259-878-91
1-244-183-11
1-216-121-91
1-259-878-91
Pending
1-247-831-91
1-247-831-91
1-247-807-91
1-247-831-91
1-247-831-91
1-247-831-91
1-216-073-91
1-247-831-91
1-247-831-91
1-216-222-91
1-247-831-91
1-244-247-11
1-240-907-11
1-216-073-91
1-247-847-91
1-216-073-91
Description
CARBON 62 1/4W
RES-CHIP 1K 1/10W
RES-CHIP 3.9K 1/10W
CARBON 470 1/4W
RES-CHIP 470 1/10W
CARBON 220 1/4W
METAL 115K 1/4W
METAL 2.8K 1/4W
CARBON 100 1/4W
METAL OXIDE 220 2W
RES-CHIP 3.3K 1/10W
CARBON 10K 1/4W
FUSIBLE 1 1W
CARBON 1.5M 1/4W
METAL 107K 1/4W
RES-CHIP 1M 1/10W
CARBON 1.5M 1/4W
CARBON 2.7K 1/4W
CARBON 1K 1/4W
CARBON 1K 1/4W
CARBON 100 1/4W
CARBON 1K 1/4W
CARBON 1K 1/4W
CARBON 1K 1/4W
RES-CHIP 10K 1/10W
CARBON 1K 1/4W
CARBON 1K 1/4W
RES-CHIP 10K 1/8W
CARBON 1K 1/4W
METAL 33.2 1/4W
METAL 30.1K 1/4W
RES-CHIP 10K 1/10W
CARBON 4.7K 1/4W
RES-CHIP 10K 1/10W
Remarks-1
Remarks-2
4050562055
4010110252
4010139252
4050547155
4010147152
4050522155
4257041153
4257042801
4050510155
4172022155
4010133252
4050510355
4181010953
4050515555
4257041073
4010110552
4050515555
4050527255
4050510255
4050510255
4050510155
4050510255
4050510255
4050510255
4010110352
4050510255
4050510255
4010810352
4050510255
4257043329
4257043012
4010110352
4050547255
4010110352
Sony
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
Others
Sony
Sony
Sony
HMD-A400(E)
7-25
No.
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
! / * Ref. No.
R921
R925
R926
R928
R929
R930
R931
R932
R933
R934
R935
R936
R937
R940
R941
R942
R943
R946
R947
R948
R949
R950
R951
R952
R953
R954
R955
R4001
R4003
R4005
R4006
R4007
R4008
R4009
Part No.
Service
1-216-049-11
1-249-429-11
1-216-025-11
1-216-073-00
1-216-222-00
1-216-222-00
1-216-222-00
1-247-791-91
1-247-791-91
1-216-166-00
1-216-222-00
1-216-121-11
Pending
1-216-222-00
1-216-166-00
1-216-166-00
1-249-417-11
1-216-174-00
1-216-017-91
1-244-347-11
1-249-429-11
Pending
1-249-425-11
1-216-017-91
1-216-073-00
1-216-065-11
1-249-429-11
1-216-029-00
1-249-429-11
1-247-862-11
1-249-441-11
1-249-440-11
Pending
1-216-025-11
Production
1-216-049-91
1-247-855-91
1-216-025-91
1-216-073-91
1-216-222-91
1-216-222-91
1-216-222-91
1-247-791-91
1-247-791-91
1-216-166-91
1-216-222-91
1-216-121-91
Pending
1-216-222-91
1-216-166-91
1-216-166-91
1-247-831-91
1-216-174-91
1-216-017-91
1-244-347-11
1-247-855-91
Pending
1-247-847-91
1-216-017-91
1-216-073-91
1-216-065-91
1-247-855-91
1-216-029-91
1-247-855-91
1-247-862-91
1-247-879-91
1-247-877-91
Pending
1-216-025-91
Description
RES-CHIP 1K 1/10W
CARBON 10K 1/4W
RES-CHIP 100 1/10W
RES-CHIP 10K 1/10W
RES-CHIP 10K 1/8W
RES-CHIP 10K 1/8W
RES-CHIP 10K 1/8W
CARBON 22 1/4W
CARBON 22 1/4W
RES-CHIP 47 1/8W
RES-CHIP 10K 1/8W
RES-CHIP 1M 1/10W
RES-CHIP 0 1/10W
RES-CHIP 10K 1/8W
RES-CHIP 47 1/8W
RES-CHIP 47 1/8W
CARBON 1K 1/4W
RES-CHIP 100 1/8W
RES-CHIP 47 1/10W
RES-CHIP 1.4 1/10W
CARBON 10K 1/4W
RES-CHIP 16K 1/10W
CARBON 4.7K 1/4W
RES-CHIP 47 1/10W
RES-CHIP 10K 1/10W
RES-CHIP 4.7K 1/10W
CARBON 10K 1/4W
RES-CHIP 150 1/10W
CARBON 10K 1/4W
CARBON 20K 1/4W
CARBON 100K 1/4W
CARBON 82K 1/4W
METAL 12.4K 1/4W
RES-CHIP 100 1/10W
Remarks-1
4010110252
4050510355
4010110152
4010110352
4010810352
4010810352
4010810352
4050522055
4050522055
4010847052
4010810352
4010110552
4010100052
4010810352
4010847052
4010847052
4050510255
4010810152
4010147052
4010114202
4050510355
4010116352
4050547255
4010147052
4010110352
4010147252
4050510355
4010115152
4050510355
4050520355
4050510455
4050582355
4257041242
4010110152
Remarks-2
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-26
No.
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
! / * Ref. No.
R4110
R4111
R4112
R4113
R4114
R4115
R4116
R4117
R4118
R4119
R5003
R5009
R5010
R5100
R5102
R5103
R5104
R5106
R5107
R5108
R5109
R5110
R5111
R5112
R5113
R5115
R5117
R5118
R5119
R5120
R5121
R5122
R5123
R5124
Part No.
Service
1-244-257-11
Pending
1-249-429-11
1-249-438-11
1-216-080-00
Pending
1-249-431-11
Pending
1-247-807-31
1-244-257-11
1-249-429-11
Pending
1-249-413-11
1-249-441-11
Pending
1-216-073-00
1-249-434-11
1-249-413-11
1-249-429-11
Pending
1-216-121-11
1-216-041-00
1-216-080-00
Pending
1-216-239-00
1-260-123-11
1-249-399-11
1-216-073-00
1-249-425-11
1-227-376-11
1-249-429-11
1-216-089-11
Pending
1-247-807-31
Production
1-244-257-11
Pending
1-247-855-91
1-247-873-91
1-216-080-91
Pending
1-247-859-91
Pending
1-247-807-91
1-244-257-11
1-247-855-91
Pending
1-247-823-91
1-247-879-91
Pending
1-216-073-91
1-247-865-91
1-247-823-91
1-247-855-91
Pending
1-216-121-91
1-216-041-91
1-216-080-91
Pending
1-216-239-91
1-260-123-91
1-247-795-91
1-216-073-91
1-247-847-91
1-227-376-11
1-247-855-91
1-216-089-91
Pending
1-247-807-91
Description
Remarks-1
METAL OXIDE 30 2W
METAL 14.3K 1/4W
CARBON 10K 1/4W
CARBON 56K 1/4W
RES-CHIP 20K 1/10W
METAL 24.9K 1/4W
CARBON 15K 1/4W
METAL 5.23K 1/4W
CARBON 100 1/4W
METAL OXIDE 30 2W
CARBON 10K 1/4W
METAL OXIDE 2.7 2W
CARBON 470 1/4W
CARBON 100K 1/4W
RES-CHIP 13K 1/10W
RES-CHIP 10K 1/10W
CARBON 27K 1/4W
CARBON 470 1/4W
CARBON 10K 1/4W
METAL CHIP 18K 1/10W
RES-CHIP 1M 1/10W
RES-CHIP 470 1/10W
RES-CHIP 20K 1/10W
RES-CHIP 6.8K 1/8W
RES-CHIP 51K 1/8W
CARBON 100K 1/2W
CARBON 33 1/4W
RES-CHIP 10K 1/10W
CARBON 4.7K 1/4W
METAL CHIP 46.4K 1/10W
CARBON 10K 1/4W
RES-CHIP 47K 1/10W
METAL CHIP 10K 1/10W
CARBON 100 1/4W
4172030053
4257041432
4050510355
4050556355
4010120352
4257042492
4050515355
4257045231
4050510155
4172030053
4050510355
4172027953
4050647155
4050510455
4010113352
4010110352
4050527355
4050547155
4050510355
419A118022
4010110552
4010147152
4010120352
4010868252
4010851352
4050110455
4050533055
4010110352
4050547255
419A146422
4050510355
4010147352
419A110022
4050510155
Remarks-2
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Others
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-27
No.
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
! / * Ref. No.
R5125
R5126
R5127
R5128
R5129
R5130
R5131
R5133
R5135
R5136
R5137
R5138
R5139
R5140
R5141
R5142
R5143
R5144
R6001
R6002
R6003
R6004
R6005
R6006
R6007
R6008
R6009
R6010
R7000
R7001
R7002
R7003
R7004
R7005
Part No.
Service
1-247-822-11
1-216-204-00
Pending
Pending
1-249-417-11
1-216-073-00
1-216-268-00
1-216-073-00
1-249-429-11
Pending
1-216-093-91
Pending
1-216-025-11
1-247-822-11
1-249-429-11
1-244-258-11
Pending
1-216-073-00
1-247-804-11
1-247-812-11
1-249-411-11
1-244-249-11
1-244-248-11
1-249-429-11
1-247-807-31
1-249-399-11
1-244-259-11
1-216-606-11
Pending
Pending
1-249-419-11
Pending
Pending
Pending
Production
1-247-822-91
1-216-204-91
Pending
Pending
1-247-831-91
1-216-073-91
1-216-268-91
1-216-073-91
1-247-855-91
Pending
1-216-093-91
Pending
1-216-025-91
1-247-822-91
1-247-855-91
1-244-258-11
Pending
1-216-073-91
1-247-804-91
1-247-812-91
1-247-819-91
1-244-249-11
1-244-248-11
1-247-855-91
1-247-807-91
1-247-795-91
1-244-259-11
1-216-004-91
Pending
Pending
1-247-835-91
Pending
Pending
Pending
Description
Remarks-1
CARBON 430 1/4W
RES-CHIP 1.8K 1/8W
CARBON 3.3 1/2W
CARBON 22 1/2W
CARBON 1K 1/4W
RES-CHIP 10K 1/10W
RES-CHIP 820K 1/8W
RES-CHIP 10K 1/10W
CARBON 10K 1/4W
METAL CHIP 10.5K 1/10W
RES-CHIP 68K 1/10W
RES-CHIP 51K 1/10W
RES-CHIP 100 1/10W
CARBON 430 1/4W
CARBON 10K 1/4W
METAL OXIDE 100 2W
FUSIBLE 0.12 1/4W
RES-CHIP 10K 1/10W
CARBON 75 1/4W
CARBON 160 1/4W
CARBON 330 1/4W
METAL 3.4K 1/4W
METAL 3.16K 1/4W
CARBON 10K 1/4W
CARBON 100 1/4W
CARBON 33 1/4W
METAL OXIDE 27K 2W
RES-CHIP 13 1/10W
RES-CHIP 18 1/10W
RES-CHIP 18 1/10W
CARBON 1.5K 1/4W
METAL CHIP 10K 1/10W
METAL CHIP 10K 1/10W
METAL CHIP 10K 1/10W
4050543155
4010818252
4050133955
4050122055
4050510255
4010110352
4010882452
4010110352
4050510355
419A110522
4010168352
4010151352
4010110152
4050543155
4050510355
4172010153
4180412853
4010110352
4050575055
4050516155
4050533155
4257043401
4257043161
4050510355
4050510155
4050533055
4172027353
4010113052
4010118052
4010118052
4050515255
419A110022
419A110022
419A110022
Remarks-2
Difference
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-28
No.
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RELAY
RELAY
SPARK GAP
SWITCH
TRANSFORMER
TRANSFORMER
TRANSFORMER
! / * Ref. No.
!
!
!
R7006
R7007
R7008
R7009
R7010
R7011
R7012
R7013
R7014
R7015
R7016
R7017
R7018
R7019
R7020
R7022
R7024
R7025
R7026
R7028
R7029
R7030
R7031
R7032
R7033
R7034
R7035
RY501
RY601
SG501
SW601
T501
T502
T503
Part No.
Service
Pending
Pending
Pending
Pending
Pending
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
1-216-097-11
1-234-471-11
1-234-472-11
1-216-121-11
1-216-121-11
1-216-121-11
1-216-061-00
Pending
1-216-097-11
Pending
1-216-612-11
1-216-612-11
1-216-612-11
1-216-612-11
1-216-612-11
1-216-612-11
1-216-612-11
1-216-612-11
1-755-423-11
1-775-031-11
1-519-422-11
Pending
1-453-362-11
1-435-986-11
1-435-984-11
Production
Pending
Pending
Pending
Pending
Pending
1-216-049-91
1-216-049-91
1-216-049-91
1-216-049-91
1-216-097-91
1-234-471-11
1-234-472-11
1-216-121-91
1-216-121-91
1-216-121-91
1-216-061-91
Pending
1-216-097-91
Pending
1-216-010-91
1-216-010-91
1-216-010-91
1-216-010-91
1-216-010-91
1-216-010-91
1-216-010-91
1-216-010-91
1-755-423-11
1-775-031-11
1-519-422-21
Pending
1-453-362-11
1-435-986-11
1-435-984-11
Description
METAL CHIP 10K 1/10W
METAL CHIP 10K 1/10W
METAL CHIP 10K 1/10W
METAL CHIP 10K 1/10W
METAL CHIP 10K 1/10W
RES-CHIP 1K 1/10W
RES-CHIP 1K 1/10W
RES-CHIP 1K 1/10W
RES-CHIP 1K 1/10W
RES-CHIP 100K 1/10W
RES, NETWORK 15k
RES, NETWORK 15k
RES-CHIP 1M 1/10W
RES-CHIP 1M 1/10W
RES-CHIP 1M 1/10W
RES-CHIP 3.3K 1/10W
RES-CHIP 0 1/10W
RES-CHIP 100K 1/10W
RES-CHIP 3.3K 1/10W
RES-CHIP 24 1/10W
RES-CHIP 24 1/10W
RES-CHIP 24 1/10W
RES-CHIP 24 1/10W
RES-CHIP 24 1/10W
RES-CHIP 24 1/10W
RES-CHIP 24 1/10W
RES-CHIP 24 1/10W
RELAY
RELAY
GAP, SPARK
POWER SWITCH (POWER)
TRANSFORMER, FLYBACK
TRANSFORMER, DRIVER
TRANSFORMER, O/P
Remarks-1
419A110022
419A110022
419A110022
419A110022
419A110022
4010110252
4010110252
4010110252
4010110252
4010110452
4082071535
4082081535
4010110552
4010110552
4010110552
4010133252
4010100052
4010110402
4010133202
4010124052
4010124052
4010124052
4010124052
4010124052
4010124052
4010124052
4010124052
4420412017
4420612014
5106152204
4410202010
7050309R00
7050209A20
7050909R00
Remarks-2
Difference
Sony
Sony
Sony
Sony
Sony
HMD-A400(E)
7-29
No.
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
#
Board
Type
D
D
D
D
D
D
D
D
D
D
D
H
H
H
H
H
H
H
TRANSFORMER
TRANSFORMER
TRANSFORMER
THERMISTOR
THERMISTOR
THERMISTOR
VARISTOR
VARISTOR
VARIABLE RESISTOR
CRYSTAL
CRYSTAL
LED
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
SWITCH
! / * Ref. No.
!
!
!
!
!
!
T504
T603
T6000
TH500
TH601
TH602
VA601
VA603
VR501
X901
X7000
LED701
R701
R702
R705
R706
R709
SW701
Part No.
Service
Pending
Pending
1-435-987-11
1-807-796-11
1-804-346-11
1-803-963-11
1-804-303-11
1-804-303-11
1-241-767-21
1-781-365-11
Pending
Pending
1-244-177-11
1-249-431-11
1-244-180-11
1-244-178-11
1-244-253-11
1-771-734-11
Production
Pending
Pending
1-435-987-11
1-807-796-21
1-804-346-11
1-803-963-11
1-804-303-11
1-804-303-11
1-241-767-21
1-781-365-11
Pending
Pending
1-244-177-11
1-247-859-91
1-244-180-11
1-244-178-11
1-244-253-11
1-771-734-11
Description
TRANSFORMER, FOCUS
TRANSFORMER, POWER
TRANSFORMER, USB POWER
THERMISTOR
THERMISTOR
THERMISTOR, PTC
VARISTOR
VARISTOR
RES, ADJ, CERMET 100K (HV ADJ)
VIBRATOR, CRYSTAL (24MHz)
VIBRATOR, CRYSTAL (6MHz)
DIODE LT6463-23-D51 (POWER)
METAL 2.15K 1/4W
CARBON 15K 1/4W
METAL 6.19K
METAL 3.83K
METAL 10.2K 1/4W
SWITCH, TACTILE (MENU)
Remarks-1
7050509R6E
7050109R00
7050159R00
7100510326
7108010038
7106070027
7112604710
7112604710
52241104E4
7152400010
7156000014
4120664630
4257042151
4050515355
4257046191
4257043831
4257041022
4410606000
Remarks-2
Difference
Others
Sony
Others
Others
Sony
Others
Others
Sony
HMD-A400(E)
7-30
HMD-A400
Sony Corporation
9-978-693-01
Computer Display Division Company
Computer Display Div.
– 83 –
English
2001BL05-Data
Made in Japan
 2001.2