Download Samsung ML-1430 Specifications

LASER PRINTER
ML-1430
SERVICE
LASER PRINTER
Manual
CONTENTS
1. Precautions
2. Specifications
3. Disassembly and Reassembly
4. Troubleshooting
5. Exploded Views and Parts List
6. Block Diagram
7. Connection Diagram
This service manual is also provided on the web,
the ITSELF system Samsung Electronics Co., Ltd.
http://itself.sec.samsung.co.kr
© Samsung Electronics Co.,Ltd. December. 2002
Printed in Korea.
VERSION NO. : 1.01
CODE : JC-0072A
- This Service Manual is a property of Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law. -
This manual is stated and
provided for service description.
All rights reserved. Any parts of the
information in this manual are prohibited
from free duplication, use or translation
without prior written approval except in
cases allowed by the Copyright Act.
Specifications are subject to change without
prior notice.
Samsung Electronics Digital Printing CS Group
Copyright (c) 2002. 12.
1. Precautions
Please read the following carefully to prevent any accidents and not to damage the unit during service.
1.1 Safety Precautions
1. Safety Precautions
There are some electric or machinery parts with
safety related property. If the parts replaced are different from the original, the safety may not function.
Even if the part could allow higher voltage than that
of the part used, do not replace it and use a regular
product clarified in specifications.
2. Be careful not to leave a switch, a cover or a safety
device out when reinstalling or assembling the product after repair.
3. Replacing Precautions
Do not change or add parts as you like. You cannot
benefit from such a remodeled product at your will
during the term of guarantee.
4. You must replace overheated or damaged parts or
cords with regular products. Please solve the problem causing any damage or overheating and troubles
beforehand.
Especially mind the safety on the part with
this mark.
You must use regular parts described in specifications for the parts inflammable and where the
current can be flown. Otherwise any hazard
such as an electric shock or a fire could occur.
LASER STATEMENT (LASERTURVALLISUUS)
WARNING : NEVER OPERATE AND SERVICE THE PRINTER
WITH THE PROTECTIVE COVER REMOVED
FROM LASER/SCANNER ASSEMBLY. THE
REFLECTIVE BEAM, ALTHOUGH INVISIBLE, CAN
DAMAGE YOUR EYES.
Class 1 laser product
Luokan 1 laserlaite
Klass 1 laser apparat
Allonpituus 770-795nm
Teho 0.3mW±0.03mW
CAUTION
INVISIBLE LASER RADIATION WHEN
THIS COVER OPEN. DO NOT OPEN
THIS COVER.
VORSICHT
UNSICHTBARE LASERSTRAHLUNG,
WENN ABDECKUNG GEOFFNET.
NIGHT DEM STRAHL AUSSETZEN.
ATTENTION
REYONNEMENT LASER INVISIBLE EN CAS
D’OUVERTURE. EXPOSITION DANGERUSE AU
FAISCEAU.
ATTENZIONE
RADIAZIONE LASER INVISIBLE IN CASO DI
APERTURA. EVITARE L’ESPOSIZONE LA FASCIO.
PRECAUCION
REDIACION LASER INVISIBLE CUANDO SE
ABRE. EVITAR EXPONERSE AL RAYO.
CAUTION : Avoid exposure to invisible laser radiation when the
development unit is not installed.
1.2 Precautions on Disassembly and Reassembly
Very careful precautions should be taken when replacing
parts. Before replacing, please check cables because
you cannot put the cables that you removed for replacing
parts into the proper place if you would not make sure of
where they were connected and in which condition.
7. When disassembling, assembling, also observe small
components are located in place.
8. If you uncover and turn the machine over to replace
some parts, toner or paper particles may contaminate
the LSU window. Protect the LSU window with clean
paper.
Please do the following before disassembling for a repair
or replacement of parts.
Releasing Plastic Latches
1. Pull out paper cassette, printer cartridge installed.
Especially careful not to be scratched by the surface of
developer or not to expose them to light.
2. Turn the power switch off.
3. Take out the power plug, printer cable from the printer.
4. Use only the same type of part as original when replacing parts.
5. Do not force to open or fasten plastic material components.
6. Be careful that small parts such as screws should not
get in the printer.
Samsung Electronics
Many of parts are held in
place with plastic latches.
The latches break easily :
release them carefully.
To remove such parts,
press the hook end of the
latch away from the part to
which it is latched.
1-1
Precautions
1.3 Tools for Troubleshooting
The following tools are recommended for safe and smooth troubleshooting described in this service manual.
1
2
DCU(Diagnostic Control Unit)
Standard: Test equipment to diagnose the
Laser printer supplied by Samsung
Electronics.
DVM(Digital Volt Meter)
Standard: Indicates more than 3 digits.
4
Driver
5
Pinset
6
Cotton Swab
7
3
Electronic Scale
Standard: Equipment to check the weight
of consumables(toner cartridge) supplied
by Samsung Electronics. (The gram unit
can be measured.)
8
Note
1-2
Standard: "-" type, "+" type (M3 long, M3
short, M2 long, M2 short).
Standard: For general home use, small
type.
Standard: For general home use, for medical service.
Cleaning Equipments a
IPA(Isopropyl Alcohol)dry cloth or a
soft stuff neutral detergent.
Software(Driver) installation CD
ROM
Mind your hands not to be touched when
you disassemble and reassemble PBA ASS'Y,
such as the main board, SMPS, HVPS.
Samsung Electronics
2. Specifications
ML-1430
Engine
Speed
Resolution
FROP(Fist Power On Time)
Warm-Up Time
Power Consumption
Dimension
Weight
Controller
14 ppm
600 x 600 dpi
Under 12.0 sec
30 sec
250 W (Print), 10W (Sleep)
329 x 355 x 231 mm (13” x 14” x 9.1”)
Max 6.5Kg (With Toner Cartridge)
Processor
Jupiter3 66MHz
Memory
8MB Equivalent
Emulation
SPL (Samsung Printer Language)
Interface
IEEE1284, USB
OS Support
Windows 95/98/2000/Me/NT,
Linux(Radhat 6.0), iMac(Mac OS 8.0)
Paper
N/W
External
Input
150 sheets
Output
100 sheets
Manual
1 sheet
Media Type
A4, Letter. Legal, Executive, B5, A5, Folio,
7 3/4(Monarch), #10, DL, C5, C6, B5
Toner
Type
Single Cartridge
Life
2,500 sheets
Cartridge
User interface
Pick up Roller
60,000 pages
Feed Roller
60,000 pages
Transfer Roller
60,000 pages
Fuser
40,000 pages
Key & LED
3Key, 4LEDs
LCD
Samsung Electronics
2,500 pages(Initial : 1,000 pages)
No
Toner Save
YES
Reprint
YES
2-1
3. Disassembly and Reassembly
3.1 Cover Assembly
3.1.1 Front Cover
1. Pull the both side of the cover to open.
4. Remove a screw of the front cover PCB and remove
the connector, then remove the cover.
2. Remove a screw and remove the stopper that holds
the printer cover.
3.1.2 Other Covers
1. Before you remove other covers, you should remove the
Front cover in advance.
2. Rear Cover : Remove the cover in the direction of a .
3. Top Cover : Remove the cover in the direction of b
.
4. Side Cover L, R : Remove the cover in the direction of c .
3. Loosen the right lower part of the cover, then push the
cover in the direction of arrow to loosen the left lower
part.
Samsung Electronics
3-1
Disassembly and Reassembly
3.2 LED Panel PBA
1. Before you remove other covers, you should remove.
3. Remove two screws, and remove LED panel.
• Front Cover (see [3.1 Main Cover])
2. Remove two screws of PCB cover, and widen the
hooks( a b c ) to remove.
4. Remove PCB from the PCB cover.
3.3 LSU(Laser Scanning Unit)
1. Before you remove LSU, you should remove front
cover, rear cover and top cover.
3. Remove two connectors from the LSU, then remove
the LSU.
• Main Cover (see [3.1 Main Cover])
2. Remove three screws securing the LSU.
3-2
Samsung Electronics
Disassembly and Reassembly
3.4 Transfer Roller
1. Open the front cover.
2. Use a proper tool("-" type screwdriver) to pull the one
end of the roller slightly, then take it out.
3.5 FAN & Motor Assembly
1. Before you remove the motor assembly, you should
remove:
• Main Cover (see [3.1 Main Cover])
3. Remove five screws securing the Motor Assembly
and remove a connector from Engine Board(Engine
board and SMPS Board are integrated), then take the
Motor Assembly out.
• Shield Engine Assembly
2. Remove one screws securing the Fan.
Shield
Ground
X
Note
O
When you reassemble the FAN, make
sure that the direction of the Fan is correct(the shield ground is downcast)
Samsung Electronics
3-3
Disassembly and Reassembly
3.6 HVPS Board
1. Before you remove HVPS board, you should remove:
•Main Cover (see [3.1 Main Cover])
2. Remove four screws and a connector from HVPS
board, then take the board out.
Note
When you reassemble the HVPS board, make
sure that five terminals should be put in place.
Terminal
3.7 Fuser Assembly
1. Before remove fuser assembly, you should remove:
• Main Cover (see [3.1 Main Cover])
3. Remove two screws and unplug a fuser assembly
harness. Then use a " - " screwdriver to unlatch the
fuser assembly to remove.
2. Remove two ground screws and a connector as illustrated.
3-4
Samsung Electronics
Disassembly and Reassembly
3.8 Thermostat and Halogen Lamp
1. Remove a screw from the fuser assembly and
remove the thermostat cover, then remove two
screws securing the thermostat.
3. Take the halogen lamp out from the Heat Roller.
Note
When you reassemble the halogen lamp,
handle it with care as it is fragile.
2. Remove two screws from the fuser assembly, and
take the Heat Roller out.
Samsung Electronics
3-5
Disassembly and Reassembly
3.9 SMPS Board
1. Before you remove the SMPS board, you should
remove:
• Main Cover (see [3.1 Main Cover])
3. Unplug connectors from the main board and connectors from SMPS, then remove the SMPS. Remove
four screws from SMPS and remove the SMPS
board.
2. Remove screws in the order of a b then remove
the shield engine assembly.
a
Note
The Engine board and SMPS board are
integrated in a body.
b
3-6
Samsung Electronics
Disassembly and Reassembly
3.10 Main Board and Sensor Board
1. Before you remove the main board, you should
remove:
3. Release four snap-fits securing the insulator engine
board and then remove the insulator.
• Main Cover (see [3.1 Main Cover])
• SMPS board (see [3.9 SMPS Board])
2. Remove two screws from the main board and unplug
all of connectors, then remove the board.
Main B’d
4. Release four snap-fits securing the sensor board and
then remove the sensor board.
Samsung Electronics
3-7
4. Troubleshooting
4.1 How to use DCU
4.4 The cause and solution of the malfunction
4.1.1 DCU Setup.......................................Page(4-2)
4.4.1 All LEDs blinking (Fuser Error) ........Page(4-16)
4.1.2 Code.................................................Page(4-2)
4.4.2 All LEDs blinking (SCAN ERROR)..Page(4-16)
4.1.3 Self Diagnostic Mode ......................Page(4-3)
4.1.4 Self Test Button.................................Page(4-4)
4.4.3 Not function of the gear of the fuser due to melting away ............................................Page(4-17)
4.1.5 Paper Path Layout............................Page(4-4)
4.4.4 Paper Empty.....................................Page(4-17)
4.4.5 Paper Empty without indication .......Page(4-17)
4.4.6 Cover Open ......................................Page(4-18)
4.2 The cause and solution of Bad image
4.2.1 Vertical Black Line and Band...........Page(4-5)
4.2.2 Vertical White Line............................Page(4-5)
4.2.3 Horizontal Black Band......................Page(4-6)
4.2.4 Black/White Spot ..............................Page(4-6)
4.4.7 No lamp on when the cover is open
...........................................................Page(4-18)
4.4.8 Defective motor operation................Page(4-19)
4.4.9 No Power ..........................................Page(4-19)
4.4.10 Vertical Line Getting Curved..........Page(4-20)
4.2.5 Light Image .......................................Page(4-7)
4.2.6 Dark Image or a Black .....................Page(4-7)
4.2.7 Uneven Density ................................Page(4-8)
4.2.8 Background.......................................Page(4-8)
4.2.9 Ghost (1) ...........................................Page(4-9)
4.2.10 Ghost (2) ..........................................Page(4-9)
4.2.11 Ghost (3)...........................................Page(4-10)
4.2.12 Ghost (4) .........................................Page(4-10)
4.2.13 Satins on the Face of Page ............Page(4-10)
4.5 Toner Cartridge Service
4.5.1 Precautions on Safe-keeping of Toner Cartridge
..........................................................Page(4-21)
4.5.2 Service for the Life of Toner Cartridge
..........................................................Page(4-21)
4.5.3 Service for Judgement of Inferior Expendables
and the Standard of Guarantee......Page(4-21)
4.5.4 Signs and Measures at Poor toner cartridge
..........................................................Page(4-22)
4.2.14 Satins on Back of Page ..................Page(4-11)
4.2.15 Blank Page Print out (1)..................Page(4-11)
4.2.16 Blank Page Print out (2)..................Page(4-11)
4.6 The cause and solutions of bad environment
of the software
4.6.1 The printer is not working (1)...........Page(4-25)
4.3 The cause and solution of the bad discharge
4.6.2 The printer is not working (2) ..........Page(4-26)
4.3.1 Wrong Print Position........................Page(4-12)
4.6.3 Abnormal Printing .............................Page(4-27)
4.3.2 JAM 0...............................................Page(4-12)
4.6.4 SPOOL Error ...................................Page(4-28)
4.3.3 JAM 1...............................................Page(4-13)
4.3.4 JAM 2...............................................Page(4-13)
4.3.5 Multi-Feeding ...................................Page(4-14)
4.3.6 Paper rolled in the fuser..................Page(4-14)
4.3.7 OPC..................................................Page(4-15)
Samsung Electronics
4-1
Troubleshooting
4.1 How to use DCU
4.1.1 DCU Setup
You can examine the malfunction of the printer. To perform DCU, open the front discharge cover and leave the connect
the harness wire(10 pin/4 pin) to the CN10(4 pin) of the Main control board.
4.1.2 Code
Connect DCU to the printer and turn the power on. It show 7 LED on the panel and each code tells the function of the
printer.
Normal Code
While printing or warming up, it indicate the position of the paper
61
00-05
Warm up
Ready(kind of paper)
20
30
40
50
69
Print Start
Feed Sensor On
Feed Sensor off
Paper Out
Sleep Mode
The printer is on, the cover is open or close.
The printer is ready, the paper is detected when the first paper is printed.
00: Legal , 01: Letter , 02: A4 , 03: EXEC , 04: B5 , 05: Folio
The engine controller received the print order from the video controller.
The paper is passing out of the Feed Sensor.
The paper has passed out of the Feed Sensor.
The paper has passed out of Exit Sensor.
The fuser power turned off to minimize the power consumption.
Error Code
When detecting the malfunction, the printing is stopped to indicate error code.
60, 62, 68
Fuser Error
64
70
71
72
73
95
Cover Open
No Paper
Paper Jam 0
Paper Jam 1
Paper Jam 2
LSU Not Ready
4-2
The error in the fuser occurred. There is a short circuit in the thermistor and the
thermostat while printing, Low Temperature Error occurs.
• 60: Open Fuser Error
• 62: Low Heat Error
• 68: Over Heat Error
The Printer Cover is open or Toner Cartridge not installed.
No paper in the paper cassette.
The front part of paper is jammed between pickup unit and Feed sensor.
The front part of paper is jammed between the Discharge sensor and Feed sensor.
The front part of paper is jammed just after passing through the discharge sensor.
LSU Scanner Motor not ready or Hsync signal not output.
Samsung Electronics
Troubleshooting
4.1.3 Self Diagnostic Mode
If Error code occurs due to malfunction of the printer, perform Self Diagnostic Mode to solve the problem.
The printer works only in the self-test mode to solve the malfunction problem.
To enter the self-test mode, turn the power on pressing the buttons of [Down], [Shift] and [Stop] at the same time.
Release the button within 2 or 3 seconds if 78 shows in the DCU. If 00 shows in the DCU, press the button [Up] or [Shift]
to select the self+test , and press the button of [Enter] to operate. To stop, press the button of [shift] and [Enter] together.
00
Main Motor Operating System
Only the main motor is in operation.
01
Main High Voltage On(THV-)
-1550 voltage output by MHV terminal.
02
Transfer High Voltage(-)On(THV-)
-1300 voltage output by MHV terminal.
03
Caution : High voltage probe should be used.
Transfer High Voltage (+)Reference on (THV +)
1300 voltage output by MHV terminal.
04
Caution : High voltage probe should be used.
Caution : High voltage probe should be used.
DEV/supply High Voltage : DEV/Supply High Voltage Test.
The left one of the three LEDs in the self-test panel is on when DEV high voltage Supply high voltage output
by each HV terminal. Press the [Up] button to switch the voltage. The middle and right one of the three LEDs
are on and -530 voltage output by DEV HV terminal.
Caution : High voltage probe should be used.
05
LSU Operating System
The scanning motor of LSU is in operation, the right LED of the three buttons on. Press the [Up] button to
Check LD. LD is functioning and the middle button is on. If the LD is normal, all LEDs are on.
06
Pickup clutch on
The Solenoid in the printer is in operation. To stop the operation, Press the button [shift] and [Enter] together.
07
Pempty/PWIDTH/New CRU Sensor Test : Pempty/PWIDTH.HEW CRU sensor test.
If activate the Actuator of the PEMPTY/PWIDTH Sensor, the left and right of the three LEDs are on.
If you install new toner Cartridge in this mode, the right LED is on.
08
Feed & Exit Sensor Test
Test the Feed sensor and Discharge sensor in the same way as '06'.
09
Cover Open Sensor Test
The same way as code '06'.
10
Fuser Test
If the [Enter] button pressed, the right LED is on and temperature of the fuser is up to READY Mode. If the
[Up] button pressed, the middle LED is on and temperature of the fuser is up to Printing Mode.
If you press the button once more, the left LED is on and temperature of the fuser is up to overheat Mode.
11
Hot Burn Test
If the [enter] button pressed, the printer is continuously printing without detection. Turn the power off to stop
operation.
12.
Cleaning Mode Print Mode
Print the paper to clean the OPC Drum in the Cartridge.
Samsung Electronics
4-3
Troubleshooting
13.
THV(+) TRIGGER. ALL HV
All high voltage output by each HV terminal and LSU and the fan is in operation. In this mode, electronic
resistance of transfer roller and high voltage is detected. If no toner cartridge in the printer, output of THV is
+199V ~ + 2100V.
14.
PTL Test
Indicates the PTL LED.
15.
Fan Test
Indicates the function of the fan.
4.1.4 Self Test Button
If the Self-Test button pressed, vertical lines are printed.
Turn the power on while pressing this button, '89' shows in the DCU and the printer is warming up. After warming-up the
printer is in READY Mode, and '88' shows in the DCU. In this mode, without any detection, the printer begins
printing(trial printing and data from the PC). It is convenient to use this mode when the engine malfunction is detected in
the control board.
FACE DOWN
PAP
ER
(150
SHE
ETS
)
REC
ORD
ED
MANUA
L 1 SHE
ET
RE
CO
RD
ED
PAP
ER
(10
0S
HE
ETS
)
4.1.5 Paper Path Layout
LSU
KNOCK UP
EXIT 2
PICK UP
CARTRIDGE
CR
DR
FUSER
H R/L
SR
OPC
IDLE
FEED
FACE UP
TR
PTL
EXIT 1
SENSOR BOARD
MAIN BOARD
Pr R/L
EXIT SENSOR
SMPS
SHIELD
4-4
EMPTY SEN
FEED SEN
SHIELD
Samsung Electronics
Troubleshooting
4.2 The cause and solution of Bad image
4.2.1 Vertical Black Line and Band
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Straight thin black vertical line occurs in the printing.
2. Dark black vertical band occur in the printing.
Check and Cause
Solution
1. Damaged develop roller in the Developer
or deformed Doctor-blade.
1. If causes 1 and 2 occur in the developer
cartridge, replace the developer and try to
print out.
2. Scratched surface of the discharge roller
in the developer, or heavily accumulated
foreign matters between the discharge
roller and fur transfer roller/ charge roller.
2. Replace the transfer roller if occurred as
No. 3.
3. Partly depression or deformation on the
surface of the transfer roller.
4.2.2 Vertical White Line
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
White vertical voids in the image.
Check and Cause
1. Foreign matter stuck onto the window of
internal lenses of LSU mirror.
2. Foreign matter or toner particles between
the developer roller and blade.
(In case the life of the developer has
been expired, white lines occur in front of
the image.)
Solution
1. Foreign matter stuck onto the window :
Clean the LSU window with recommended cleaner(IPA) Clean the window with a
clean cotton swab.
2. Foreign matter in the LSU : Open the
cover of LSU and clean with a cotton
swab on the surface of the reflex mirror.
3. It may occur when Burr and foreign substances are on the window of the developer frame.
3. No 3. : Remove the foreign matter and
burr of the exposure window.
4. If the fuser is defective, voids occur periodically at the top of a black image.
4. No. 4. : Open the front cover and check
ribs that corresponds to the position of
the voids. Remove if found.
5. If the problems are not solved, check to
see if the weight of the developer is
below 670g. If so, replace the developer
cartridge.
Samsung Electronics
4-5
Troubleshooting
4.2.3 Horizontal Black Band
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Dark or blurry horizontal stripes occur in the printing periodically.
(They may not occur periodically.)
Check and Cause
Solution
1. Bad contacts of the voltage terminals to
developer.
1. Clean each voltage terminal of the Charge,
Supply, Develop and Transfer roller.
(remove the toner particles and paper particles)
2. The rollers of developer may be stained.
Charge roller = 37 mm
Supply roller = 27 mm
Develop roller = 32 mm
Transfer roller = 47 mm
2. Clean the right Gear that has relatively
small gap of the teeth in the OPC.
3. If the malfunction persists, replace the
developer.
4.2.4 Black/White Spot
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
1. Dark or blurry black spots occur periodically in the printing.
2. White spots occur periodically in the printing.
Check and Cause
Solution
1. If dark or blurry black spots occur periodically, the rollers in the Developer may be
contaminated with foreign matte or paper
particles.
( Charge roller : 37 mm interval
OPC drum : 75mm interval)
1. Run OPC cleaning Mode Print and run the
Self-test 2 or 3 times.
2. If faded areas or voids occur in a black
image at intervals of 75 mm, or black
spots occur elsewhere, the OPC drum
surface is damaged.
2. In case of 75mm interval unremovable in 1,
cleanly remove foreign substances stuck on
the OPC location equivalent to black spots
and white spots with a dry duster.
3. If a black image is partially broken, the
transfer voltage is abnormal or the transfer roller's life has expired.
3. The transfer roller guarantees 50,000
sheets printing. If the roller's life is expired,
replace it.
4. In case of 37mm interval unremovable in 1,
take measures as to replace the developer
cartridge and try to print out.
5. Clean the inside of the set against the paper
particles and foreign matter in order not to
cause the trouble.
4-6
Samsung Electronics
Troubleshooting
4.2.5 Light Image
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
The printed image is light, with no ghost.
Check and Cause
Solution
1. Develop roller is stained when the toner
of developer cartridge is almost consumed.
1. Check if the Toner Save mode is off.
2. Ambient temperature is below than 10°C.
2. Replace the developer cartridge and try to
print out.
3. Wait 30 minutes after printer is powered on
before you start printing.
3. Bad contact caused by the toner stains
between the high voltage terminal in the
HVPS and the one in the set.
4. Clean up the contaminated area by the
toner.
4. Abnormal output from the HVPS.
(Run self-test and check 1~4)
5. Replace the HVPS if the problems are not
solved by the above four directions.
( Service parts : Figure 11, Chapter 5)
4.2.6 Dark Image or a Black
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
The printed image is dark.
Check and Cause
Solution
1. No charge voltage in the engine board.
( Perform DCU diagnostic code 01)
1. Clean the high voltage charge terminal.
2. Charge voltage is not turned on due to
the bad contacts between power supply
in the side of the Developer and charge
terminal of HVPS.
2. Check the state of the connector which
connects the engine board and HVPS.
3. Replace the HVPS if not solved by the
above direction 1 and 2.
Samsung Electronics
4-7
Troubleshooting
4.2.7 Uneven Density
• Description
Print density is uneven between left and right.
Check and Cause
Solution
1. The pressure force on the left and right
springs of the transfer roller is not even,
the springs are damaged, the transfer
roller is improperly installed, or the transfer roller bushing or holder is damaged.
1. Replace both the left and right Spring
Holder.
2. The toner level is not even on the developer roller due to the bad blade.
2. Occur in the developer cartridge, replace
the developer and try to print out.
4.2.8 Background
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
4-8
Light dark background appears in whole area of the printing.
Check and Cause
Solution
1. Recycled recording paper has been
used.
1. B/S is not guaranteed when using recycled
paper.
2. The life of the Developer has expired.
(The weight at the expiration of the
developer's life: 800 ± 20g)
2. Replace the Developer that has expired.
3. The up-to-down movement of the transfer roller is swift?
3. Clean the busing part of the transfer roller.
4. The HVPS is normal?
(Perform DCU diagnostic code 01~04)
4. Replace the Developer if not solved by the
above direction 1~3.
Samsung Electronics
Troubleshooting
4.2.9 Ghost (1)
• Description
75mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Ghost occurs at 75 mm intervals of the OPC drum in the whole printing.
Check and Cause
Solution
1. Bad contacts caused by contamination
from toner particles between high voltage
terminal in the main body and the electrode of the Developer.
1. Clean the terminals when contaminated by
toner particles.
2. Bad contacts caused by contamination
from toner particles between high voltage
terminal in the main body and the one in
the HVPS board.
2. Occur in the developer cartridge, replace
the developer and try to print out.
3. The life of developer is expired.
3. Replace the engine board if not solved by
the above directions 1-2.
(Service Parts : Figure 9 , chapter 5)
4. Transfer roller lifetime(50,000 sheets) has
expired.
4. If not solved by the direction 3, check the
transfer roller lifetime and replace it.
(Service Parts : Figure 8-2 , chapter 5)
5. Abnormal low temperature(below 10°C).
5. Wait about 1 hour after power on before
using printer.
4.2.10 Ghost (2)
• Description
Samsung Electronics
75mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Ghost occurs at 75 mm intervals of the OPC drum in the whole printing.
(When printing on card stock or transparencies using manual feeder)
Check and Cause
Solution
When printing on card stock thicker than normal paper or transparencies such as OHP,
higher transfer voltage is required.
Select 'Thick Mode' on paper type menu from
the software application and after using returning to the original mode is recommended.
4-9
Troubleshooting
4.2.11 Ghost (3)
• Description
Check and Cause
Digital
Digital Printer
Printer
Solution
1. The life of the developer may be expired.
1. Occur in the developer cartridge, replace
the developer and try to print out.
2. The abnormal voltage and bad contact of
the terminal of the supply roller
roller.
2. Check the approved voltage of the supply
roller and contact of the terminal and adjust
if necessary.
32mm
Digital
Digital Printer
Printer
Digital
Digital Printer
Printer
White ghost occurs in the black image printing at 32mm intervals.
4.2.12 Ghost (4)
• Description
Check and Cause
47mm
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Ghost occurs at 47mm intervals.
The temperature of the fuser is maintained
high.
Solution
1. Disassemble the fuser and remove the
contaminated toner particles on the roller
and clean the foreign matter between
Thermistor and Heat roller.
(
Caution: can be deformed)
4.2.13 Satins on the Face of Page
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
4-10
The background on the face of the printed page is stained.
Check and Cause
Solution
1. Toner leakage due to improperly sealed
developer.
1. Replace the developer cartridge.
2. If the transfer roller is contaminated, satins
on the face of page will occur.
2. If the transfer roller is contaminated, run PC
Cleaning Mode Print 2 or 3 times.
And perform Self-Test 2 or 3 times to
remove contamination.
Samsung Electronics
Troubleshooting
4.2.14 Satins on Back of Page
• Description
Digital
Digital Pri
Digital Printer
Digital Printer
Digital Printer
The back of the page is stained at 47mm intervals.
Check and Cause
Solution
1. Transfer roller is contaminated.
1. Perform the OPC Cleaning Mode Print 2 or
3 times. Run Self-Test to remove the contamination of the transfer roller.
2. Pressure roller is contaminated.
2. Replace the transfer roller if contaminated
severely.
3. Disassemble the fuser and clean the
H/R(Heat Roller) and P/R(Pressure roller).
And check the area between H/R and
Thermistor. If contaminated, clean the area
not to be deformed.
4.2.15 Blank Page Print out (1)
• Description
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Blank page is printed.
Check and Cause
Bad ground contacts in OPC and/or developer.
Solution
Remove contamination of the terminals of the
developer and the unit.
4.2.16 Blank Page Print out (2)
• Description
1. Blank page is printed.
2. One or several blank pages are printed.
3. When the printer turns on, several blank pages print.
Check and Cause
Solution
1. Bad ground contacts in OPC and/or
developer.
1. Remove contamination of the terminals of
the developer.
2. Abnormal solenoid.
2. Perform the engine self test using DCU to check
if the Solenoid is normal.(refer to code 06)
3. If not solved by the above directions 1-2,
Replace the engine board.
(Service Parts : Figure 9 , chapter 5)
4. Turn the power off, delete the data of PC
and try printing again.
Samsung Electronics
4-11
Troubleshooting
4.3 The cause and solution of the bad discharge
4.3.1
Wrong Print Position
• Description
Printing begins at wrong position on the paper.
Check and Cause
Solution
Wrong sense time caused by defective feed sensor
actuator.
Replace the defective actuator
(Service Parts : Figure 8-16 , chapter 5)
4.3.2 JAM 0
1. Paper is not exited from the cassette.
2. Jam-0 occurs if the paper feeds into the printer.
• Description
Check and Cause
Solution
1. Check the Solenoid by using DCU
diagnostic mode 06.
1. Replace the solenoid. (Service Parts :
Figure 8-11 , chapter 5)
2. Check if the pad is loose due to bad
sealing of the side-pad.
2. Replace the side-pad Assembly L or
R, if necessary.
(Service Parts : Figure 8-13 , 8-14,
chapter 5)
LSU
EXIT 2
PICK UP
CARTRIDGE
FEED SEN
EXIT 1
EXIT SENSOR
JAM 0
3. Check the surface of the roller-pickup for foreign matter.
4. If continuous clusters occur, check
whether the assembly slot between
shaft-pickup and housing-pickup
become open or is broken away.
3. Clean with soft cloth dampened with
IPA(Isopropyl Alcohol) or water.
4. Replace the Housing-Pickup and/or
Shaft-Pickup.
(Service Parts : Figure 8-135, 8-12, chapter 5)
5. If the paper feeds into the printer
rand Jam 0 occurs, perform DCU to
check feed-sensor of the sensor
board.
4-12
Samsung Electronics
Troubleshooting
4.3.3
JAM 1
1. Recording paper is jammed in front of or inside the fuser.
2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the
Actuator-Feed.
• Description
Check and Cause
LSU
EXIT 2
Solution
1. If the recording paper is jammed in
front of or inside the fuser.
(Perform DCU diagnostic code of)
1. Replace the SMPS. (Service Parts :
Figure 10, chapter 5)
2. If the recording paper is stuck in the
discharge roller and the fuser just
after passing through the ActuatorFeed, Feed Actuator may be defective.
2. Reassemble the Actuator-Feed and
Spring-Actuator if the returning is bad.
PICK UP
CARTRIDGE
FEED SEN
FEED
EXIT 1
EXIT SENSOR
JAM 1
4.3.4 JAM 2
1. Recording paper is jammed in front of or inside the fuser.
2. Recording paper is stuck in the discharge roller and in the fuser just after passing through the
Actuator-Feed.
• Description
LSU
EXIT 2
PICK UP
CARTRIDGE
FEED SEN
EXIT 1
EXIT SENSOR
JAM 2
Samsung Electronics
Check and Cause
Solution
1. If the paper is completely fed out of
the printer, but Jam 2 occurs : Exit
sensor is defective.
• After the paper is completely discharged, actuator Exit should return
to the original position to shut the
photo-sensor. Sometimes it takes
longer hour than it should and does
not return.
1. Check if the exit sensor actuator is
defective.
• Check if the actuator exit is unformed
(Check if the lever part is unformed
in shape).
• Check whether burrs occur in the
assembly part of the actuator exit or
not and if the actuator is smoothly
operated.
• Check if foreign matters and wire get
caught in the actuator exit's operation.
2. If the paper is rolled in the Fuser Roller:
• This occurs when a Guide claw is
broken away or transformed.
• It occurs when the Spring of a Guide
claw is broken away or transformed.
• It occurs when the Heat-Roller or
Pressure-Roller is seriously contaminated with the toner.
2. If the paper is stuck in the fuser : disassemble the fuser and remove the
jammed paper, and clean the surface
of the pressure roller with dry gauze.
3. Paper is accordion in the fuser.
3. Remove the jammed paper after disassembling the fuser : Clean the surface
of the pressure roller with dry gauze.
• Remove the toner particles stained
on the rib.
• Check the assemblage and performance of the exit.
4-13
Troubleshooting
4.3.5 Multi-Feeding
• Description
Multiple sheets of paper are fed at once.
Check and Cause
Solution
1. Solenoid malfunction(the solenoid does not work
properly): Perform DCU mode : solenoid check 06.
1. Replace the solenoid if necessary.
(Service Parts : Figure 13, chapter 5)
2. Pad-Friction is contaminated with foreign matter.(oil...)
2. Clean the pad friction with soft clothe dampened
with IPA(Isopropyl Alcohol).
3. The face of paper is blended.
3. Use the smooth paper.
4.3.6 Paper rolled in the fuser
• Description
If contaminated at intervals of 57mm on the back of a paper.
Check and Cause
1. Contamination of the pressure roller.
(Background, Hot off set)
Solution
1. Disassemble the fuser, clean the area between the
Heat-roller and Thermistor and remove the foreign
matter of the pressure roller.
2. If background appears badly in the printing, fix it by
referring to the solutions for background.
(See 4.2.8 Background)
4-14
Samsung Electronics
Troubleshooting
4.3.7
OPC
• Description
Paper is rolled up in the OPC.
Check and Cause
Solution
1. Paper is too much thin.
1. Recommend to use normal paper.
2. The face of paper is curled.
2. How to remove the rolled paper in the OPC.
• Remove the paper while turning the OPC against
the ongoing direction.
• Clean fingerprints on the OPC softly with soft
cloth dampened with IPA(Isopropyl Alcohol) or tissue.
Samsung Electronics
4-15
Troubleshooting
4.4 The cause and solution of the malfunction
4.4.1 All LEDs blinking (Fuser Error)
• Description
1. All the lamps on the operator panel blink.
2. Gear of the fuser does not work and breaks away melt away.
When printing, motor breaks away from its place due to defective fuser gear.
Check and Cause
Solution
1. Check if the thermostat, AC wire and Heat Lamp is
open.
1. If the thermostat is open replace the fuser and
check following items.
2. Check if the thermistor sensor is in place.
2. If the thermistor sensor device is located deep in the
sponge, replace the fuser.
3. Check if the heat lamp works properly.
3. Check if the circuit of overheat mode works properly.
4. Check if the overheat circuit works properly.
4. Run DCU mode : Perform DCU diagnostic code 10.
5. The fuser gear is defective due to melting away.
4.4.2 All LEDs blinking (Scan Error)
• Description
1. All lamps on the operator panel blink.
Check and Cause
DCU Mode : Perform DCU diagnostic code 05. If the DCU
error code 95 is displayed, replace LSU.
Solution
Replace LSU.
(Service Parts : Figure 13, chapter 5)
If you cannot solve the problem after you replace LSU,
replace the main board.
4-16
Samsung Electronics
Troubleshooting
4.4.3 Not function of the gear of the fuser due to melting away
• Description
The motor breaks away from its place due to gear melting away.
Check and Cause
DCU Mode : Check if the Error States '60' '62' '68' occur.
Check the operation of Fuser Erasing Lamp On/Off with
the Error Code Check -10-.
Solution
1. Replace the Fuser.
(Service Parts : Figure 8-4, Chapter 5)
2. Replace the Main Control board.
(Service Parts : Figure 9, Chapter 5)
4.4.4 Paper Empty
• Description
The paper lamp on the operator panel is on even when paper is loaded in the cassette.
Check and Cause
Solution
1. Bending or deformation of the actuator of the paper sensor.
1. Replace the defective actuator.
(Service Parts : Figure 8-17, Chapter 5)
2. The function of the sensor board is defective Perform
DCU mode: Perform DCU diagnostic code 8.
2. Replace the sensor board.
(Service Parts : Figure 8-10, Chapter 5)
4.4.5 Paper Empty without indication
• Description
The paper lamp on the operator panel does not come on when the paper cassette is empty.
Check and Cause
Solution
1. Bending or deformation of the actuator of the paper sensor.
1. Replace the defective actuator.
(Service Parts : Figure 8-17, chapter 5)
2. The function of the sensor board is defective Perform.
DCU mode : Perform DCU diagnostic code 8.
2. Replace the sensor board.
(Service Parts : Figure 8-10, chapter 5)
Samsung Electronics
4-17
Troubleshooting
4.4.6 Cover Open
• Description
The ERROR lamp is on even when the print cover is closed.
Check and Cause
Solution
1. The hook lever in the top cover may be defective.
1. Replace the hook lever, if defective.
(Service Parts : Figure 1, chapter 5)
2. Check the connector and circuit of the cover switch
department in the Main Control board. Perform DCU
mode : If Error state '64' occurs, Check the related codes
of the Cover Open Error.
2. Check the insertion of the Cover Open Sensor
Connect.
3. Replace the Main Control board or Cover Open
Sensor.
(Service Parts : Figure 9, chapter 5)
Hook Lever
4.4.7 No lamp on when the cover is open
• Description
The ERROR lamp does not come on even when the printer cover is open
Check and Cause
1. Check the connector(CN8) and circuit of the cover switch
department in the Main Control board. Perform DCU
mode : If Error state '64' occurs, Check the related codes
of the Cover Open Error
Solution
1. Check the insertion of the Cover Open Sensor
Connect.
2. Replace the Main Control board or Cover Open
Sensor.
(Service Parts : Figure 9, chapter 5)
4-18
Samsung Electronics
Troubleshooting
4.4.8 Defective motor operation
• Description
Main motor is not driving when printing, and paper does not feed into the printer, resulting 'Jam 0'.
Check and Cause
Solution
1. Motor harness or sub PCB may be defective.
1. Check the motor harness, replace it, if defective.
(Service Parts : Figure 12, chapter 5)
2. Perform DCU diagnostic code 00 and Check the motor
operation.
2. Replace the SMPS, if necessary.
(Service Parts : Figure 10, chapter 5)
4.4.9 No Power
• Description
When system power is turned on, all lamps on the operator panel do not come on.
Check and Cause
Solution
1. Check if the power input and SMPS output are normal.
1. Replace the power supply cord or SMPS.
(Service Parts : Figure 10, chapter 5)
2. Check the inferiority of LED-Panel on the front-cover if
the LED of Panel does not appear after normal warmingup.
2. Replace the control board.
(Service Parts : Figure 9, chapter 5)
3. Replace the LED-panel.
(Service Parts : Figure 1-1, chapter 5)
Samsung Electronics
4-19
Troubleshooting
4.4.10 Vertical Line Getting Curved
• Description
When printing, vertical line gets curved.
Check and Cause
1. If the supply of +24v is unstable in the Main Control board
linking with LSU, check drive by DCU Mode: LSU Check
-05- LSU Motor on.
Solution
1. Replace LSU.
(Service Parts : Figure 13, chapter 5)
2. Replace the Main Control board.
(Service Parts : Figure 9, chapter 5)
4-20
Samsung Electronics
Troubleshooting
4.5 Toner Cartridge Service
It is not guaranteed for the default caused by using other toner cartridge other than the cartridge supplied by the
Samsung Electronic or caused by non-licensed refill production.
4.5.1 Precautions on Safe-keeping of Toner Cartridge
Excessive exposure to direct light more than a few minutes may cause damage to the cartridge.
4.5.2 Service for the Life of Toner Cartridge
If the printed image is light due to the life of the toner, you can temporarily improve the print quality by redistributing the
toner(Shake the toner cartridge), however, you should replace the toner cartridge to solve the problem thoroughly.
4.5.3 Service for Judgement of Inferior Expendables and the Standard of Guarantee
Please refer to User's Manual or Instructions on Fax/Printer Expendables SVC for the judgement of inferior expendables and the standard of guarantee besides this service manual.
Samsung Electronics
4-21
Troubleshooting
4.5.4 Signs and Measures at Poor toner cartridge
Fault
Light image and
partially blank
image
(The life is ended.)
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Signs
Cause & Check
• The printed image
is light or unclean
and untidy.
1. If the image is light or unclean
and untidy printed image Shake the developer and
then recheck.
• Some part of the
(1)NG: Check the weight of the
image is not printdeveloper
ed.
(2)OK: Lack of toner, so the life
is nearly closed.
• Periodically a noise 2. Some part of image is not
as "tick tick" occurs.
printed - Shake the developer and then recheck.
(1)NG: Check the weight of the
developer and clean
the LSU window with a
cotton swab, then
recheck.
(2)OK: Lack of toner, so the life
is nearly closed.
3. Periodically a noise as "tick
tick" occurs - Measure the
cycle and the weight of the
developer.
4. White vertical stripes on the
whole screen or partly :
Check the weight of the
developer.
Toner
Contamination
• Toner is fallen on
the papers periodically.
• Contaminated with
toner on prints partly or over the whole
surface.
Solution
1. All of 1, 2, 3 above(1)The weight of the developer
ended: 800g ± 20g
(2)If it become better by shaking,
replace with a new developer
after 50-100 sheets in the closing state of the life span.
2. In case of 2If it becomes better after cleaning the LSU window, then the
developer is normal.
(Because of foreign substance
on the LSU window, the image
has not been printed partly.)
3. In case of 3If the cycle of noise is about 2
seconds, the toner inside the
developer has been nearly
exhausted.( Purchase and
replace with a new developer
after using about 200 sheets at
the point of occurrence)
4. In case of 3This is a phenomenon caused
by lack of toner, so replace with
a new developer.
1. Toner is fallen on the paper
periodically.
(1)Check the cycle of the
falling of the toner.
(2)Check the appearance of
both ends of the developer
OPC drum.
1. If both ends of the OPC drum
are contaminated with toner:
Check the life of the developer.
(In case of less than 820g, the
life may be expired.)
2.The center of the printed matter is contaminated with toner.
(1)Check whether foreign substances or toner are stuck
to the terminal (contact
point) of the developer.
(2)Check whether the state of
the terminal assembly is
normal.
2. Check whether it could be recycled.
3. If it cannot be recycled:
Replace the developer.
4-22
Samsung Electronics
Troubleshooting
Fault
White Black spot
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer
Signs
Cause & Check
1. If light or dark periodical black
dots occur, this is because the
developer rollers are contaminated with foreign substance
or paper particles.
• White spots occur
in the image period- (1)35mm interval : Charged
roller
ically.
(2)75mm interval : OPC cycle
• Light or dark black
dots on the image
occur periodically.
2. If white spots occur in a black
image at intervals of 75mm, or
black spots occur elsewhere,
the OPC drum is damaged or
foreign substance is stuck to
the surface.
Recycled product
Samsung Electronics
Solution
1. In case of 1 above Run OPC Cleaning Mode Print
4-5 times repeatedly to remove.
Especially check foreign substance on the OPC surface, then
remove them with a clean gauze
moistened with IPA(Isopropyl
Alcohol) not to damage OPC if
necessary.
Never use usual alcohol.
2. In case of 2
If they are not disappeared by
running OPC Cleaning Mode
Print 4-5 times.
: at intervals of 37mm - Replace
the developer.
: at intervals of 75mm - Remove
foreign substance.
: Broken image - Replace the
developer according to carelessness.
3. If a black and white or graphic
image is partially broken at
irregular intervals, the transfer
roller's life has been expired or
the transfer voltage is abnormal.
3. In case of 3 - Exchange the
transfer roller because the life of
the transfer roller in use has been
expired. (Check the transfer voltage and readjust if different.)
• Poor appearance of 1. Poor appearance of the develthe developer.
oper.
(1)Check the damage to label
• Unclean and rough
and whether different materiprintouts.
als are used.
(2)Check the appearance of
• Bad background in
parts of the developer, such
the image.
as frame, hopper.
1. In case of 1 (1)If there is an evidence of disassembling the developer.
(2)If materials other than normal
parts of the developer are
added or substituted.
2. Unclean and rough printouts.
(1)Check whether foreign substance or toner are stuck to
the terminal (contact point) of
the developer.
(2)Check whether the state of
the terminal assembly is normal.
2. In case of 2 - If there are any
abnormals in connection with the
situation of 1.
(1)It occurs when the developer
is recycled over 2 times.
(2)If toner nearly being expired
are collected to use, it is
judged as the recycled developer.
4-23
Troubleshooting
Fault
Ghost & Image
Contamination
Signs
Cause & Check
Solution
• The printed image
is too light or dark,
or partially contaminated black.
1. The printed image is too light
or dark, or partially contaminated black.
(1)Check whether foreign substance or toner are stuck to
the terminal(point of contact)
of the developer.
(2)Check whether the terminal
assembly is normal.
1. All of 1, 2, 3 above
(1)Remove toner and foreign substances adhered to the contact
point of the developer.
(2)The contact point of the unit
facing that of the developer
also must be cleaned.
(3)If the terminal assembly is
unsafe:
• Fully stick the terminal to or
reassemble it after disassembling.
• Disassemble the side plate and
push the terminal to be stuck,
then reassemble it.
2. Totally contaminated black.
(Black image printed out)
(1)Check whether foreign substances are stuck to the terminal(point of contact) of the
developer and the state of
assembly.
(Especially check the
charged roller terminal.)
2. In case of 2
It is a phenomenon when the
OPC drum of the developer is not
electrically charged. Clean the
terminals of the charged roller,
then recheck it.
3. The printed image is dark and
ghost occurs.
(1)Check foreign substance
attached to the terminal
(point of contact) of the
developer and the state of
assembly.
(Especially check the developing roller terminal.)
3. In case of 3
It is a phenomenon as the developing bias voltage of the developer. Clean the terminals of the
developing roller, then recheck it.
• Totally contaminatedblack.
(Black image printed out)
• The density of printouts is too dark and
ghost occurs.
4-24
Samsung Electronics
Troubleshooting
4.6 The cause and solutions of bad environment of the software
4.6.1 The printer is not working (1)
• Description
While Power turned on, the printer is not working in the printing mode.
Check and Cause
Solution
1. Run Self-Test Mode: Turn the power on while pressing
the test printing button for 2 or 3 seconds before printing
works.
1.Check the power of the printer and perform the SelfTest. If the test printing works, that means no problems in the printer itself. If the test printing does not
work, that means bad functioning of the printer(not
because of software). Perform DCU to check the
Error Status.
2. Check if the PC and the printer is properly connected
and the toner cartridge installed.
2. Replace the printer cable. If the problems not solved
even after the cable replaced, check the amount of
the remaining tone.
(refer to Toner Cartridge Service 4-5)
3. Printing is nor working in the Windows.
3. Check if the connection between PC and printer port
is proper. If you use windows, check if the printer driver in the controller is set up. If the printer driver is
properly set up, check in which program the printing
is not working. The best way to find out is to open the
memo pad to check the function of printing. If it is not
working in a certain program, adjust the setup the
program requires. Sometimes, the printout is normal
within the Windows basic programs, but it's not working in a particular program. In such case, install the
new driver again. If not working in the Windows basic
program, Check the setup of the port of CMOS is on
ECP. And check the address of IRQ 7 and 378
4. Check if the printer cable is directly connected to peripheral devices
Samsung Electronics
4. If the scanner needs to be connected to the printer,
first the remove the scanner from the PC to see if the
printer is properly working alone.
4-25
Troubleshooting
4.6.2 The printer is not working (2)
• Description
After receiving the printing order, no response at all or the low speed of printing
occurs due to wrong setup of the environment rather than malfunction of the printer itself.
Check and Cause
Solution
1. Secure more space of the hard disk.
1. Not working with the message 'insufficient printer
memory' means hard disk space problem rather than
the RAM problem. In this case, provide more space
for the hard disk. Secure more space using the disk
utilities program.
2. Printing error occurs even if there is enough space in
the hard disk.
2. The connection of the cable and printer port is not
proper. Check if the connection is properly done and
if the parallel port in CMOS is rightly set up.
3. Check the parallel-port-related items in the CMOS
Setup.
3. As a printer port, Select ECP or SPP among
SPP(Normal), ECP, and EPP modes(increase printing speed) SPP normal mode support 8-bit data
transfer, while ECP Mode transfer the 12-bit data.
4. Reboot the system to print.
4. If the regular font is not printing, the cable or the
printer driver may be defective.
Turn the PC and printer off, and reboot the system
to print again. If not solved, double-click the printer in
my computer If the regular fonts are not printed this
time again. the cable must be defective so replace
the cable with new one.
4-26
Samsung Electronics
Troubleshooting
4.6.3 Abnormal Printing
• Description
The printing is not working properly even when the cable has no problem.
(even after the cable is replaced)
If the printer won't work at all or the strange fonts are repeated, the printer driver may be defective or wrong setup in the CMOS Setup.
Check and Cause
Solution
1. Set up the parallel port in the CMOS SETUP.
1. Select SPP(Normal) or ECP LPT Port the among
ECP, EPP or SPP in the CMOS Setup.
2. Printer Driver Error.
2. Check the printer in My Computer.(to see if the
printer driver is compatible to the present driver or
delete the old driver, if defective and reinstall the new
driver)
3. Error message from insufficient memory.
(The printing job sometimes stops or due to insufficient
virtual memory, but it actually comes from the insufficient space of the hard disk.)
3. Delete the unnecessary files to secure enough
space of the hard disk and start printing job again.
Samsung Electronics
4-27
Troubleshooting
4.6.4 SPOOL Error
• Description
To spool which stands for "simultaneous peripheral operations online" a computer document or
task list (or "job") is to read it in and store it, usually on a hard disk or larger storage medium so
that it can be printed or otherwise processed at a more convenient time (for example, when a
printer is finished printing its current document).
Check and Cause
Solution
1. Insufficient space of the hard disk in the directory
assigned for the basic spool.
1. Delete the unnecessary files to provide more space
to start printing job.
2. If the previous printing error not solved.
2. If there are some files with the extension name of
****.jnl, Delete them and Reboot the Windows to
restart printing job.
3. When expected to collide with other program.
3. Shut down all other programs except the current
one, if possible.
4. When an application program or the printer driver is
damaged.
4. Delete the printer driver completely and reinstall it.
5. When some files related to OS are damaged or virus
infected.
5 After rebooting the computer, check for viruses,
restore the damaged files and reinstall the program
to do the printing job.
6. Memory is less than suggested one.
6. Add up enough memory to the PC.
How to delete the data in the spool manager.
In the spool manager, the installed drivers and the list of the documents waiting to be printed are shown.
Select the document to be deleted and check the delete menu.
If you intend to delete the current document being printed, the data being transferred to the printer will be put
out and then the document is removed. Before choosing the document, the menu is still inactive.
Or put the document out of the list and repeat the routine as in the above or finish the spool manager.
4-28
Samsung Electronics
5. Exploded Views and Parts List
5.1
5.2
5.3
5.4
5.5
5.6
5.7
Main Assembly................................................................................... page(5-2)
Front Cover Assembly...................................................................... page(5-4)
Shield Engine Unit Assembly.......................................................... page(5-5)
Frame Lower Assembly.................................................................... page(5-6)
Engine Assembly............................................................................... page(5-8)
Fuser Assembly................................................................................. page(5-10)
Plate-Upper Unit Assembly.............................................................. page(5-12)
For the latest exact information, see ITSELF System. (http://itself.sec.samsung.co.kr)
Samsung Electronics
5-1
Exploded Views and Parts List
5-1 Front Cover Assembly
0
7
3
4
13
5
16
11
6
17
8+9
2
14
12-1
1
12
10
15
5-2
Samsung Electronics
Exploded Views and Parts List
Main Assembly Parts List
O : Service available X : Service not available
No.
1
2
3
4
5
6
7
8
9
10
11
12
12-1
13
14
15
16
17
Description
SEC.Code
Q’ty
SA
ELA UNIT-CVR FRONT ,1430
PMO-STACKER RX
PMO-COVER TOP
PMO-COVER REAR
PMO-COVER SIDE(L)
PMO-COVER_SIDE R 14
MEC-TRAY(P)
ELA UNIT-FRAME LOWER,1430
ELA UNIT-FRAME LOWER,1430
MEA ETC-ENGINE,1430
ELA UNIT-SMPS_V1
ELA UNIT-SMPS_V2_CHANA
SMPS-HVPS
ELA UNIT-RX DRIVE
MOTOR-STE 7.5
UNIT-LSU
PBA MAIN-CON 14
PBA MAIN-CON 14
ELA HOU-SHIELD_ENGINE
MEC-PLATE UPPER
MEA UNIT-TONER CARTRIDGE
*
JC72-00302A
JC72-00522A
JC75-00094A
JC72-00523A
JC72-00955A
JC75-00099A
JC96-02544A
JC96-02544B
*
JC96-02559A
JC96-02234B
JC44-00024A
JC96-02125A
JC31-00005B
JC59-00017A
JC92-01413A
JC92-01413B
*
JC75-00111A
*
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
X
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
X
O
X
Samsung Electronics
Remark
ML-1430/XAA,/XAC
ML-1430/XIL, /XEV
ML-1430/XAA,/XAC
ML-1430/XIL, /XEV
ML-1430/XAA,/XAC,/XEV
ML-1430/XIL
5-3
Exploded Views and Parts List
5-2 Front Cover Assembly
0
11
2
3
5
10
4
13
10
8
6
1
12
9
7
Front Cover Assembly Parts List
O : Service available X : Service not available
No.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
5-4
Description
SEC.Code
Q’ty
SA
ELA UNIT-CVR FRONT,1430
CBF HARNESS-FRONT PANEL
PMO-COVER FRONT
PMO-COVER FRONT
COVER-M-FRONT(XEV)
PMO-GUIDE STACKER
PMO-DOOR FACE UP
PPR-SHEET PAPER GUIDE
PMO-KEY A
PMO-KEY B
PMO-LENS SED
PMO-COVER PCB
PMO-STOPPER
PMO-BRKT PUSH DEVE
PBA SUB-LED PANEL
NPR-BADGE
*
JC39-00112C
JC72-00677W
JC72-00677Y
JC63-00133A
JC72-00511A
*
*
*
*
*
JC72-00678A
JC72-00519A
*
JC92-01280A
*
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
X
O
O
O
O
O
X
X
X
X
X
O
O
X
O
X
Remark
ML-1430/XAA,/XAC
ML-1430/XIL
ML-1430/XEV
Samsung Electronics
Exploded Views and Parts List
5-3 Shield Engine Unit Assembly
0
2
S-1
3
S-3
S-2
1
1-1
1-2
Shield Engine Unit Assembly Parts List
O : Service available X : Service not available
No.
0
1
1-1
1-2
2
3
Description
ELA HOU-SHIELD_ENGINE 1210
MEC-SHIELD BRKT CONTROL
IPR-SHIELD ENGINE,USB
IPR-BRKT CONTROLLER
PCT-INSULATOR_SMPS1210
CBF HARNESS-INLET-SWITCH
Samsung Electronics
SEC.Code
Q’ty
SA
*
JC75-00105C
JC70-00130C
JC70-00131A
JC72-00828A
JC39-00134A
1
1
1
1
1
1
X
O
O
O
O
O
Remark
5-5
Exploded Views and Parts List
5-4 Frame Lower Assembly
2
2-2
2-3
2-1
0
2-4
15
33
34
12
3
4
5
10-2
10-1
10
31
6
6
3-1
2-3
2-1
17
35
25
16
9
1
24
22
23
8
7
21
26
11
19
13
22
23
21
29
14
30
18
26
38-2
38
32
38-1
36
37
39
20
28
27
5-6
Samsung Electronics
Exploded Views and Parts List
Frame Lower Assembly Parts List
O : Service available X : Service not available
No.
0
1
2
2-1
2-2
2-3
2-4
3
3-1
3-2
3-3
4
5
6
7
8
9
10
10-1
10-2
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
38-1
38-2
39
Description
ELA UNIT-FRAME LOWER,KOR 1430
ELA UNIT-FRAME LOWER,KOR 1430
PMO-FRAME LOWER
MEA UNIT-HOLDER-TR,L CKD
PMO-HOLDER-TR
PMO-BUSHING_TR(L)
SPRING ETC-TR,L 1210
IPR-PLATE_TR
MEA UNIT-HOLDER-TR,R CKD
PMO-HOLDER-TR
PMO-BUSHING_TR(R)
SPRING ETC-TR(300)
PMO-CAP PLTE G/DEV R
PMO-CAP PLTE G/DEV L
SPRING ETC-GUIDE DEVE
PMO-ACTUATOR_EXIT,14
PMO-HOLDER EXIT,14
PMO-BUSHING_TERMINAL
ELA HOU-OPEN SENSOR
IPR-BRKT-SENSOR
CBF HARNESS-COVER
IPR-GUIDE-TR
IPR-PLATE-TERMINAL
IPR-SAW_PLATE
PCT-FILM SAW
IPR-EARTH TRANS
IPR-GROUND_GUIDE
IPR-GROUND_HVPS
IPR-GROUND_FUSER
IPR-GROUND DRIVE
CBF HARNESS-OPE GND
PMO-HOLDER PR
BEARING-PRESSURE R
SPRING ETC-PR_1430
MEC-ROLLER_PR,1430
PMO-GUIDE_INPUT 14
RMO-RUBBER_FOOT
AS-FUSER 110V
AS-FUSER 220V
CBF HARNESS-FUSER(110V)
ELA HOU-MOTOR GND,Z
PMO-BUSHING SHAFT
PMO-HINGE FRONT(L)
PMO-HINGE FRONT(R)
PMO-COVER PTL
ELA HOU-PTL ASS’Y
PCT-COVER SHEET LAMP
MEC-ROLLER FEED
PBA MAIN-SENSOR
MEC-HOLDER FEED
PMO-ACTUATOR_FEED
PMO-ACTUATOR_EMPTY
PCT-INSULATOR SENSOR BD
Samsung Electronics
SEC.Code
JC96-02544A
JC96-02544B
JC72-00533B
*
*
JC72-00102A
JC61-00458A
*
*
*
JC72-00101A
JC61-00024A
*
*
*
JC72-00957A
JC72-00956A
*
JC96-01584A
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
JC75-00159A
*
*
JC81-00808A
JC81-00809A
*
*
JG72-40849A
*
*
JC72-00534A
JC96-02037A
*
JC75-00054A
JC92-01197A
JC75-00055A
JC72-00119A
*
*
Q’ty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SA
O
O
O
X
X
O
O
X
X
X
O
O
X
X
X
O
O
X
O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
X
X
O
O
X
X
O
X
X
O
O
X
O
O
O
O
X
X
Remark
ML-1430/XAA,/XAC
ML-1430/XIL, /XEV
110V
220V
5-7
Exploded Views and Parts List
5-5 Engine Assembly
13
19
21
21-1
19-2
21-2
19-1
17
17-3
21-3
17-1
17-2
15
16
14
10
4
14-2
12
20-1
14-1
20-3
20-2
20-4
20
2
18
18-1
18-3
18-2
9 8
1
5
3
22
11 6
23
7
5-8
Samsung Electronics
Exploded Views and Parts List
Engine Assembly Parts List
O : Service available X : Service not available
No.
0
1
2
3
4
5
6
7
8
9
10
11
12
14
14-1
14-2
15
16
17
17-1
17-2
17-3
18
18-1
18-2
18-3
19
19-1
19-2
20
20-1
20-2
20-3
20-4
21
21-1
21-2
21-3
22
23
Description
MEA ETC-ENGINE,1430
FAN-DC
SOLENOID-SWALLOW
SPRING ETC-CLUTCH
SPRING ETC-KNOCK UP
CBF HARNESS-MOTOR
CBF HARNESS-MAIN_HVPS
IPR-CLAMP EMI
PMO-GEAR_FEED
PMO-CLUTCH_FEED
PMO-CAP_PAD
CBF HARNESS-PANEL MAIN
RPR-PAD_DAMPER
MEC-TERMINAL
IPR-TERMINAL
SPRING ETC-HV APOLLO
MEC-SIDE PAD(L)
MEC-SIDE PAD(R)
MEC-KNOCK UP ASS’Y
PMO-PLATE-KNOCK UP
PMO-CAM-KNOCK UP
IPR-BAR_KNOCK UP
MEC-GEAR PICK UP
PMO-GEAR_PICKUP,1
PMO-GEAR_PICKUP,2
SPRING ETC-PICK UP GEAR
MEC-CAM PICK UP
PMO-CAM_PICKUP
PMO-SHAFT_PICKUP
MEA UNIT-HOLDER PAD 1210
PMO-HOLDER PAD LARGE
PMO-HOLDER_PAD,S 6200
RPR-PAD FRICTION
SPRING ETC-PAD
MEA UNIT-TRANSFER ROLLER 1430
PMO-GEAR_TRANSFER
PPR-SPACER_TR
MEC-ROLLER_TRANSFER 1430
CBF HARNESS-THERMISTOR
CBF HARNESS-LSU
Samsung Electronics
SEC.Code
Q’ty
SA
*
3103-001085
JC33-00002B
*
*
*
*
*
*
*
JC72-00124A
*
*
JC75-00049A
JC70-00050A
*
*
JC75-00051B
JC75-00053A
*
*
*
JC75-00056A
*
*
*
JC75-00072A
*
*
JC97-01486A
*
*
*
*
*
*
*
JC75-00157A
*
*
1
1
1
1
1
1
1
1
1
1
1
1
2
5
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
X
O
O
X
X
X
X
X
X
X
O
X
X
O
O
X
X
O
O
X
X
X
O
X
X
X
O
X
X
O
X
X
X
X
X
X
X
O
X
X
Remark
5-9
Exploded Views and Parts List
5-6 Fuser Assembly
0
24
30
29
27
26
28
24
23
25
17
21
7
S-1
13
2
9
12
20
31
15
4
16
1
18
S-2
14-1
14-2
22 17
10
11
14
S-1
5
3
S-1
8
19
6
5-10
Samsung Electronics
Exploded Views and Parts List
Fuser Assembly Parts List
O : Service available X : Service not available
No.
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
14-1
14-2
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Description
AS-FUSER ASS’Y 110V
AS-FUSER ASS’Y 220V
THERMISTOR-NTC
THERMOSTAT
LAMP-HALOGEN
LAMP-HALOGEN
PMO-COVER FUSER
PMO-BUSHING H/R L
PMO-BUSHING H/R R
PMO-COVER_THERMOSTAT
NPR-ROLLER HEAT,411
IPR-ELECTRODE_PLATE
IPR-GROUND_FU
PMO-GUIDE CLAW
IPR-ELECTRODE WIRE1
IPR-ELECTRODE WIRE,S
MEA ETC-SHAFT EXIT
PMO-SHAFT_EXIT(Z15)
RMO-RUBBER_EXIT
PMO-ROLLER_IDLE EXIT
SPRING ETC-EXIT
PMO-GEAR_EXIT_DRV16
PMO-GEAR_EXIT_IDLE
GEAR-FUSER 1210
LABEL(P)-CAUTION, HOT_FUSER
SPRING ETC-EXIT DOWN
SPRING ETC-CLAW
GEAR-EXIT F/DOWN
BEARING-EXIT FU L
PMO-COVER FUSER F/DOWN
PMO-HOLDER_EXIT_DOWN
PMO-EXIT_DOWN,L
PMO-EXIT_DOWN,S
RMO-RUBBER-KICKER
MEC-EXIT,F/DOWN
IPR-PIN ROLLER EXIT
Samsung Electronics
SEC.Code
Q’ty
SA
Remark
JC81-00808A
JC81-00809A
1404-001188
4712-000001
4713-001155
4713-001156
*
*
*
*
JC71-00012B
*
*
*
*
*
*
*
*
*
*
*
*
JC66-00037B
*
*
*
*
*
*
*
*
*
*
*
*
1
1
1
1
1
1
1
1
1
1
1
1
1
5
1
1
1
1
4
4
4
2
1
1
1
4
5
1
1
1
4
4
4
8
1
4
O
O
O
O
O
O
X
X
X
X
O
X
X
X
X
X
X
X
X
X
X
X
X
O
X
X
X
X
X
X
X
X
X
X
X
X
110V
220V
100V
220V
5-11
Exploded Views and Parts List
5-6 Plate-Upper Unit Assembly
0
6
1
3-3
7
4
3-2
3
3-1
8
3-3
7
2
4
8
2
5
Plate-Upper Unit Assembly Parts List
O : Service available X : Service not available
No.
0
1
2
3
3-1
3-2
3-3
4
5
6
7
8
5-12
Description
MEC-PLATE UPPER
IPR-UPPER-PLATE
IPR-PLATE SPRING DEV
MEA ETC-ROLLER PICK UP
PMO-HOUSING_PICKUP
PMO-IDLE_PICKUP
RMO-ROLLER_PICKUP
SPRING ETC-FEED
ICT-ROLLER IDEL FEED
CABLE CLAMP
PMO-HOLDER_PICKUP
PMO-HOLDER_IDLE,FEED
SEC.Code
Q’ty
SA
JC75-00111A
*
*
*
JC72-00109A
*
*
*
*
*
*
*
1
1
2
1
1
2
1
2
1
1
2
2
O
X
X
X
O
X
X
X
X
X
X
X
Remark
Samsung Electronics
Samsung Electronics
3 KEY
4 LED
PANEL
B' D
PC
IEEE 1284 CABLE
USB
Osci l l ator
44 MHz
VOL TAGE
DETECT OR
74LVX161284
Line
Transcei ver
Vi deo
Clock
Po we r
On
Re s e t
S3C46M0X
CPU
Jupiter3
MAIN
THVPWM
BI ASPWM
BUFFER
FS781BZB
MHVPWM
Mai n
Clock
Crystal
10MHz
( 8MB)
SDRAM
( 0 .5MB)
FLASH
MEMORY
B' D
HV PS
LSU
EXI T
SENSOR
+24V
+5V
Engine
SMP S
TH V
DEV
SUPPLY
OPC GND
MHV
I N-LET
POWER
SWI TCH
DEV_FUSE
FAN
SOLENOIDE
MOTOR
POWER
CORD
6. Block Diagram
6-1
7. Connection Diagram
IEEE1284
COMPATI ABLE
CABLE
HOST
COMPUTER
DCU
1
2
3
4
USB CABLE
36
PI N
J1
SENSOR
BOARD
1
2
3
4
+5V
*PEMPTY
* FEED
+5V GND
COVER
SW ITCH
1
2
3
+24V
Not Use d
+24VS
1
THERMI STOR 2
HV PS
1
2
3
4
5
6
7
8
9
+24V_T
+24V GND
THV PWM
*THV_EA
THVRE AD
* M H VP WM
BI ASPW M
+5V
+5V GND
1
2
3
4
5
1
2
3
4
5
6
1
2
3
4
CN13
1
2
3
4
5
6
7
8
9
+5V
+5V GND
LED_ERROR
LED_PAPER
LED_DATA
LED_TONER
* KEY_TONER
* KEY_CANCEL
* KEY_DEMO
1
2
3
4
5
6
7
8
9
CN6
1
2
+5V
PTL
1
2
CN3
CN1
SPL
1
2
3
4
1
2
3
CN7
Main
Board
CN11
CN5
THERM_A
THERM_B
+24V_T
+24V GND
*PMOTOR
+3. 3V
EXT_C LK
* HSYNC
+5V
+5V GND
* LD_ON
VDO
+5V GND
POLYGON
MOTOR
LSU
LD DIODE
4PI N
CONNECTOR
f or
USB
+5V
DCU_DATA
DCU_CLK
+5V GND
CN9
1
2
3
4
5
6
7
8
9
10
11
1
2
1
2
3
4
5
6
7
8
9
CN12
CN8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
+5V GND
+5V
+5V GND
+5V
+5V GND
+5V
+24V GND
+24V
+24V GND
+24V
+24V GND
+24V
EXIT
+24VS
FUSER ON
+24VS
* EGMOT_B1
CLUTCH
EGMOT_PHB
FA N
DEV_FUSE
* EGMOT _A1
* NEW_DEVE
EGMOT_PHA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
LED
DISPLAY
PANEL
PTL LEDARRAY
SMPS
FUSER
CN502
CN5
SOL ENOID
ENGINE
CN1
STEPPING
MOTOR
CN2
DEV_FUSE
CN3
FAN CN4
ENGI NE + SMPS
Unification B’ d
Samsung Electronics
7-1
Repair Manual
LASER PRINTER
ML-1430
CONTENTS
1. Block Diagram
2. Connection Diagram
3. Schematic Diagrams
This manual is made and
described centering around
circuit diagram
and circuit description needed
in the repair center
in the form of appendix.
Samsung Electronics Digital Printing
CS Group
Copyright (c) 2002. 4
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3 KEY
4 L ED
P ANE L
B’ D
PC
IEEE 12 84 CABLE
USB
Osci l l ator
44 MHz
VOL TAGE
DETECT OR
74LVX161284
Li ne
Transcei ver
Vi deo
Clock
Po we r
On
Re s e t
S3C46M0X
C P U
Jupiter3
MAIN
THVPWM
BI ASPW M
BUFFER
FS781BZB
MHVP WM
Mai n
Clock
Crystal
10MHz
( 8MB)
SDRAM
( 0 .5MB)
FLASH
MEMORY
B’ D
HV PS
LSU
EXI T
SENSOR
+24V
+5V
Eng i ne
SMP S
TH V
DEV
SUPPL Y
OPC GND
MHV
I N- L ET
POWER
SWI TCH
DEV_FUSE
FAN
SOLENOIDE
MOTOR
POWER
CORD
1
B LOCK DIAG R A M
1. Block Diagra m
1.1 SPL Block Diagram(ML-1430)
Repair Manual
1-1
C O N N E C T I O N D I AG R A M
2
2. Connection Diagra m
2.1 SPL Connection Diagram(ML-1430)
IEEE1284
COMPATI ABLE
CABLE
HOST
COMPUTER
DCU
1
2
3
4
USB CABLE
36
PI N
J1
CN3
1
2
3
4
CN1
CN7
SENSOR
BOARD
1
2
3
4
+5V
*PEMPTY
* FEED
+5V GND
1
2
3
4
COVER
SWITCH
1
2
3
+24V
Not Use d
+24VS
1
2
3
CN13
1
THERMI STOR 2
HV PS
1
2
3
4
5
6
7
8
9
+24V_T
+24V GND
THV PWM
*THV_EA
THVRE AD
* M HVPWM
BI ASPW M
+5V
+5V GND
1
2
3
4
5
1
2
3
4
5
6
1
2
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
+5V
+5V GND
LED_ERROR
LED_PAPER
LED_DATA
LED_TONER
* KEY_TONER
* KEY_CANCEL
* KEY_DEMO
1
2
3
4
5
6
7
8
9
1
+5V
PTL
1
2
CN6 2
Main
Board
CN11
CN5
THERM_A
THERM_B
+24V_T
+24V GND
*PMOTOR
+3. 3V
EXT_C LK
* HSYNC
+5V
+5V GND
* LD_ON
VDO
+5V GND
POLYGON
MOTOR
LSU
LD DIODE
4PI N
CONNECTOR
f or
USB
+5V
DCU_DATA
DCU_CLK
+5V GND
CN9
1
2
3
4
5
6
7
8
9
10
11
CN12
CN8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
+5V GND
+5V
+5V GND
+5V
+5V GND
+5V
+24V GND
+24V
+24V GND
+24V
+24V GND
+24V
EXIT
+24VS
FUSER ON
+24VS
* EGMOT_B1
CLUTCH
EGMOT_PHB
FA N
DEV_FUSE
* EGMOT _A1
* NEW_DEVE
EGMOT_PHA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
LED
DISPLAY
PANEL
PTL LEDARRAY
SMPS
FUSER
CN502
CN5
SOL ENOID
ENGINE
CN1
STEPPING
MOTOR
CN2
DEV_FUSE
CN3
FAN CN4
ENGI NE + SMPS
Unification B’d
Repair Manual
Samsung Electronics
- This Document can not be used without Samsung's authorization -
2-1
S C H E M ATIC DIAG R A M S
3
3. S ch e m atic Diagra m s
3.1 Main Circuit Diagram (1/5)
Repair Manual
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-1
S C H E M ATIC DIAG R A M S
Main Circuit Diagram (2/5)
3-2
Repair Manual
Samsung Electronics
- This Document can not be used without Samsung's authorization -
S C H E M ATIC DIAG R A M S
Main Circuit Diagram (3/5)
Repair Manual
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-3
S C H E M ATIC DIAG R A M S
Main Circuit Diagram (4/5)
3-4
Repair Manual
Samsung Electronics
- This Document can not be used without Samsung's authorization -
S C H E M ATIC DIAG R A M S
Main Circuit Diagram (5/5)
Repair Manual
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-5
S C H E M ATIC DIAG R A M S
3.2 HVPS Circuit Diagram (1/2)
5V
18V
C402
103
R401
100
R403
110KF
Q401
A708-Y
MHV-PWM
3
CN1-#6
T401
KAB-006
R405
220KF
R411
2.2K
R422
5.6K
24VS
R407
240K
R404
33K
12
13
4
Q402
D526-Y
14
-
D111
1N4148
R402
56KF
U2-B
7407
+
1
7
5
2
6
R426
MGR1/2W 100KF
MHV
R413
MGR1/2W 6MF
C405
2KV 680
R408
47K
U1-D
KA324
D401
4KV
C404
3KV 471
C406
3KV 471
D402
4KV
R414
MGR1/2W 6MF
4
R412
2K
C408
104
C401
222
R409
430
R406
2.2KF
C403
333
VR401
50K
OPC
R410
1W 3
ZD401
1W 130V
D403
1N4148
24VS
5V
T501
KAB-006
18V
R501
5.6K
R503
100
R510
47K
C503
104
R508
86.6KF
Q502
D526-Y
1
CN1-#7
2
U2-A
7407
R507
27K
R502
2.2K
R505
100KF
R506
100KF
-
10
+
8
7
5
2
6
C502
222
VR501
50K
R509
12KF
R514
MGR1/2W 15MF
R417
MGR1/2W 15MF
R516
MGR1/2W 50K
SUPPLY
C505
2KV 680
C506
3KV 471
ZD501
1W 100V
4
R511
47K
U1-C
KA324
C501
104
R504
2K
9
D502
4KV
1
Q501
A708-Y
BIAS-PWM
R416
MGR1/2W 15MF
R515
MGR1/2W 15MF
R512
430
C504
333
D501
1N4148
R513
1W 3
DEV
R519
MGR1/2W 50K
R517
MGR1/2W 15MF
CN1
GIL-S-9P-S2T2-EF
1
2
3
4
5
6
7
8
9
3-6
24VS
A-GND
THV-PWM
THV-EA
THV-READ
MHV-PWM
BIAS-PWM
5V
D-GND
24VS
U3
KA7818
IN
18V
OUT
+
GND
C1
104
C2
104
C3
35V 47uF
Repair Manual
Samsung Electronics
- This Document can not be used without Samsung's authorization -
S C H E M ATIC DIAG R A M S
HVPS Circuit Diagram (2/2)
T201
HVT-2A
24VS
5V
18V
1
C208
6KV 471
C206
6KV 471
7
D204
6KV
R201
10K
THV-PWM
R206
100
13
CN1-#3
12
11
10
U2-F
7407
R205
1K
U2-E
7407
24VS
+
Q204
D526-Y
D201
1N4148
R208
30KF
Q203
A708-Y
5
C201
103
R209
110KF
R207
2K
U1-B
KA324
C101
35V 47uF
VR201
50K
C202
331
6
R210
510KF
R213
2.2K
7
D202
1N4148
C207
6KV 471
C209
6KV 471
THV
R212
470K
C203
D203
472 1N4148
ZD201
5.6V
R215
430
R216
BR1/2W 30MJ
R218
MGR1/2W 100KF
C204
473
ZD202
7.5V
R217
BR1/2W 200MG
18V
R3
1/2W 560
ZD1
5.6V
18V
C7
104
R309
2.2K
14
CN1-#4
C205
6KV 101
D207
6KV
4
R211
1MF
THV-EA
6
D206
6KV
-
R214
1.2K
5V
CN1-#8
+
5
2
D205
6KV
9
T301
KAB-006
Q301
A708-Y
1
C307
3KV 471
D304
4KV
7
8
R315
BR1/2W 30MJ
R307
33K
7
U2-C
7407
5
2
18V
D-GND
6
C306
2KV 680
Q303
D526-Y
24VS
D303
4KV
C308
3KV 471
4
D301
1N4148
C4
104
R308
33K
R310
2.2K
4
THV-READ
+
1
R316
1KF
CN1-#5
-
U1-A
KA324
Q302
A708-Y
3
2
R302
33K
R303
100KF
R306
26.1KF
R304
200KF
R314
2.2KF
R311
100KF
VR302
5K
C305
333
11
C303
333
R317
2KF
R305
5.1KF
R301
470K
C302
102
D302
1N4148
VR301
10K
C304
500V 103
C301
222
Repair Manual
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-7
S C H E M ATIC DIAG R A M S
3.3 SMPS Circuit Diagram (110V)
R502
F501
1/2W
560K
125V 8A
F502
LF501
125V 3A
APOLLO12
LF502
APOLLO12
V501
SCK-054
T501
R518
C522
EER2828
22
1KV 102
CN501
3W
47K
104
C520
300uH
C504
U502
R513
+24VS
FB
330
2.2K-F
50V 33uF
2A 223K
5
7
R504
PC501
R511
C518
K1010H
4.3K
N5
CN5-1,3,5
R515
C513
1uF
C515
10V
1000uF
U503
68K
KA431
1
R521
R520
150
47K
+5V 1.0A
C517
104
EXIT
CN5-14
R516
OP501
2.2K-F
ITR8406-S
PC501
1/2W
1.5K
+5V
R512
10
NB
C510
1W
0.3
L502
D503
6
R510
1KV 102
SB1040FCT
C509
KMOC3063
104
10uH
APOLLO12
1W 180
FUSIBLE
PC502
C514
22
3
R508
R514
30
4
104
3
C507
1/4W
100
C519
5W
500
GND
R507
ER102
5
VCC
OCP
BTA12-600
R503
DRAIN
GND
1
U501
2
2
1
D501
B501
STRT-G6153
R519
CN5-8,10,12
2
333
11
3
D502
C521
UF1010
2KV 221K
L501
N24
NP
1W
47K
CN502
12
1
C512
1W 47
FUSIBLE
CN5-7,9,11
+24V 1.8A
R506
R501
D504
ER1002FCT
C511
C505
222MAD
R509
1W
82
10V 470uF
FL406
C502
TNR502 C503
1W
47K
R517
50V 1000uF
BD501
TNR501
R505
50V 1000uF
+
103
-
200V 470uF
N
C508
222MAD
224
F.G
C501
TVR 10D 561K
TVR 14D 221K
L
CN5-2,4,6
K1010H
C506
GND
222MAD
CN5-13,15
+24VS2
NO MARKING RESISTOR 1/4W-J (5%)
50V 47uF
GND
12 16 5
2B
331
CN2
1
17
1
2
2
4
3
4
C2
RC2
SENSE2
2A
E2
+ENABLE1
+ENABLE2
GND
1B
VREF
1A
E1
14
7
PHASE1
RC1
+EGMOT_A1
+EGMOT_B1
C1
U1
A2918SWH
VBB
VCC
5
PHASE2
SENSE1
13
8
+24VS
+24V
CN4
GND
11
EGMOT_PHA
EGMOT_PHB
CN5-16
C3
15 18 3 6 9
35303-0450
+5V
331
FAN
3
2
1
35301-0350
Q3
R13
2.2K
D3
1N4003
C8
1N4003
50V 47uF
FUSER_ON
1008-Y
CLUTCH
R2
R12
510
D2
CN1
2
1
35303-0250
Q1
1008-Y
R1
5.6K
5.6K
GND
GND
R7
GND
3-8
56K
C7
103
R6
GND
2W 0.37
R11
2W 0.37
C5
331
1.2K
R8
R10
1K
1K
C6
R5
103
R15
56K
C4
331
GND
R9
17.4K-F
GND
Repair Manual
Samsung Electronics
- This Document can not be used without Samsung's authorization -
S C H E M ATIC DIAG R A M S
SMPS Circuit Diagram (220V)
R502
F501
1/2W
560K
250V 5A
F502
LF501
250V 2A
APOLLO12
V501
LF502
T501
SCK-054
APOLLO12
R518
C522
22
1KV 102
EER2828
CN501
3W
47K
CN5-7,9,11
C520
1KV 221K
1W
100K
300uH
C504
333
U502
1/4W
22
R513
FB
330
4
50V 33uF
5
R504
7
PC501
K1010H
4.3K
N5
CN5-1,3,5
R515
2.2K-F
R511
10
NB
C518
C513
1uF
C515
10V
1000uF
22K
U503
KA431
1
R521
R520
150
47K
+5V 1.0A
C517
104
EXIT
CN5-14
R516
OP501
2.2K-F
ITR8406-S
CN5-2,4,6
K1010H
C506
GND
332MAD
CN5-13,15
+24VS
R512
PC501
1/2W
1.5K
+5V
2A 223K
1W
0.6
L502
D503
C510
R510
1KV 102
SB1040FCT
C509
KMOC3063
C514
22
10uH
6
PC502
R514
30
1W 180
FUSIBLE
104
104
GND
APOLLO12
3
R508
C507
C519
5W
500
CN5-8,10,12
R507
ER102
5
VCC
OCP
BTA12-600
R503
DRAIN
GND
1
U501
2
2
1
D501
B501
STRT-G6153
CN502
R519
3
1W 47
FUSIBLE
11
3
D502
C521
UF1010
C512
L501
N24
NP
10V 470uF
104
+24V 1.8A
12
1
R506
R501
D504
ER1002FCT
C511
C505
222MAD
R509
1W
82
2
FL406
C502
C503
1W
100K
R517
103
BD501
TNR501
R505
50V 1000uF
+
450V 150uF
N
-
224
F.G
C508
222MAD
50V 1000uF
C501
TVR 10D 561K
L
+24VS2
NO MARKING RESISTOR 1/4W-J (5%)
50V 47uF
VBB
+ENABLE1
2A
+ENABLE2
2B
12 16 5
CN2
1
17
1
2
2
4
3
4
C2
RC2
SENSE2
E2
GND
VREF
1B
E1
14
7
331
1A
SENSE1
+EGMOT_A1
+EGMOT_B1
U1
A2918SWH
PHASE1
PHASE2
RC1
13
8
CN4
5
VCC
11
+24V
+24VS
C1
GND
GND
EGMOT_PHA
EGMOT_PHB
CN5-16
C3
35303-0450
+5V
331
15 18 3 6 9
FAN
3
2
1
35301-0350
Q3
R13
2.2K
D3
1N4003
C8
1N4003
50V 47uF
FUSER_ON
1008-Y
CLUTCH
R2
CN1
2
1
35303-0250
Q1
R12
510
D2
1008-Y
R1
5.6K
5.6K
GND
R7
GND
R11
56K
C7
103
R8
R6
GND
1K
2W 0.37
331
1K
2W 0.37
R10
C5
1.2K
R5
C6
103
R15
56K
C4
331
GND
R9
17.4K
GND
Repair Manual
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-9
S C H E M ATIC DIAG R A M S
3.4 Panel Circuit Diagram
3-10
Repair Manual
Samsung Electronics
- This Document can not be used without Samsung's authorization -
- This Service Manual is a property of Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law. -