Download Allied Telesyn International Corp AT-VP504E FXS (SIP/MGCP) Specifications
Transcript
MIB Structure (SIP/MGCP/NCS) VoIPTalk Reference Manual Rev C Copyright © 2001 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA USA 94085 All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn International, Corp. reserves the right to make changes in specifications and other information contained in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesyn International, Corp. be liable for any incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost of profit, arising out of or related to this manual or the information contained herein, even if Allied Telesyn International, Corp. has been advised of, known, or should have known, the possibility of such damages. Contents MIB Reference Manual Contents Chapter 1 MIB Structure ........................................................................................... 1 What is a MIB? ............................................................................................................ 1 Allied Telesyn MIB Structure ................................................................................................... 1 Storage Clauses ...................................................................................................................... 2 Changing a Parameter Value .................................................................................................. 2 Switching Protocols ................................................................................................................. 2 Manual Conventions.................................................................................................... 3 MIB Version ................................................................................................................. 4 Part 1: Provisioning MIB Chapter 2 InterfaceGroup Parameters..................................................................... 7 Basic Interface Parameters ......................................................................................... 7 interfaceStaticGroup.................................................................................................... 7 interfaceDhcpGroup .................................................................................................... 8 interfaceQoSGroup Parameters .................................................................................. 8 interfaceVlanGroup Parameters .................................................................................. 9 Chapter 3 apaManager Parameters ....................................................................... 11 apaManager Basic Parameters ................................................................................. 11 apaManagerStaticGroup ........................................................................................... 11 apaManagerDhcpGroup ............................................................................................ 12 Chapter 4 apaUIGroup Parameters........................................................................ 13 apaUIMapRuleGroup Parameters ............................................................................. 13 apaUIMapRulexGroup ........................................................................................................... 13 VP500 Communication Unit iii Contents MIB Reference Manual apaUIServicesGroup ................................................................................................. 14 apaUIServicesPortnGroup..................................................................................................... 14 Chapter 5 gatewayGroup Parameters ................................................................... 17 gatewayGroup Basic Parameter................................................................................ 17 gatewayPortnGroup................................................................................................... 17 gatewayPermLocalSameACGroup............................................................................ 18 gatewayPermLocalDiffACGroup................................................................................ 18 gatewayPermLongDistSameACGroup ...................................................................... 19 gatewayPermLongDistDiffACGroup .......................................................................... 19 gatewayPermLongDistDiffCCGroup .......................................................................... 20 Chapter 6 countryGroup Parameters .................................................................... 21 Country Parameters .................................................................................................. 21 Chapter 7 portGroup Parameters........................................................................... 23 General Parameters .................................................................................................. 23 portnDspGroup .......................................................................................................... 24 portnDspUserGainGroup ....................................................................................................... 24 portnDspCountrySpecificGroup ............................................................................................. 25 portnDspCodecGroup............................................................................................................ 25 portnDtmfGroup ......................................................................................................... 27 Chapter 8 syslogGroup Parameters ...................................................................... 29 syslogGroup Basic Parameters ................................................................................. 29 syslogStaticGroup ..................................................................................................... 29 syslogDhcpGroup ...................................................................................................... 30 Chapter 9 tftpGroup Parameters............................................................................ 31 tftpGroup Basic Parameters ...................................................................................... 31 VP500 Communication Unit iv Contents MIB Reference Manual tftpServerStaticGroup ................................................................................................ 31 tftpServerDhcpGroup................................................................................................. 32 Chapter 10 apaByPassGroup Parameters .............................................................. 33 apaByPassGroup Parameters ................................................................................... 33 Chapter 11 apaSystemGroup Parameters............................................................... 35 apaSystemGroup Parameters ................................................................................... 35 Chapter 12 apaCmdGroup Parameters ................................................................... 37 apaCmdGroup Parameters ....................................................................................... 37 Chapter 13 snmpGroup Parameters ........................................................................ 39 snmpGroup Parameters ............................................................................................ 39 Chapter 14 apaInfoGroup Parameters..................................................................... 41 apaInfoInterface Parameters ..................................................................................... 41 apaInfoTftpGroup ...................................................................................................... 41 apaInfoFileConfigGroup ............................................................................................ 42 Chapter 15 configTrapGroup Parameters ............................................................... 43 Config Trap Parameters ............................................................................................ 43 VP500 Communication Unit v Contents MIB Reference Manual Chapter 16 sntpGroup Parameters .......................................................................... 45 General Parameters .................................................................................................. 45 sntpStaticGroup Parameters ..................................................................................... 45 sntpDhcpGroup Parameters ...................................................................................... 46 sntpTimeZoneConfigGroup Parameters.................................................................... 46 Part 2: MGCP MIB Chapter 17 mgcpConfiguration Parameters ........................................................... 51 Introduction................................................................................................................ 51 General Parameter .................................................................................................... 51 mgcpConfigurationEpIdGroup ................................................................................... 52 mgcpConfigurationCallAgentGroup ........................................................................... 52 mgcpConfigurationCallAgentStaticGroup .............................................................................. 52 mgcpConfigurationCallAgentDhcpGroup .............................................................................. 53 mgcpConfigurationRetransmissionGroup.................................................................. 53 mgcpConfigurationGenericMediaPackageGroup ...................................................... 54 mgcpConfigurationDtmfPackageGroup ..................................................................... 54 mgcpConfigurationLinePackageGroup...................................................................... 55 mgcpStatusGroup Parameters .................................................................................. 55 mgcpStatisticsGroup Parameters .............................................................................. 56 Part 3: SIP MIB Chapter 18 sipUAGroup Parameters ....................................................................... 59 Introduction................................................................................................................ 59 sipUA Basic Parameters............................................................................................ 59 sipUALogGroup ......................................................................................................... 60 sipUALogStaticGroup ............................................................................................................ 60 sipUALogDhcpGroup............................................................................................................. 60 sipUAServerGroup .................................................................................................... 61 VP500 Communication Unit vi Contents MIB Reference Manual sipUAServerStaticGroup ....................................................................................................... 61 sipUAServerDhcpGroup ........................................................................................................ 61 sipUAnGroup ............................................................................................................. 62 sipUAnAuthGroup.................................................................................................................. 63 sipUAAuthGroup........................................................................................................ 63 Appendix A List of MIB Parameters .......................................................................... 65 VP500 Communication Unit vii Contents VP500 Communication Unit MIB Reference Manual viii List of Tables MIB Reference Manual List of Tables Table 1 –––– Table 2 –––– Table 3 –––– Table 4 –––– Table 5 –––– Table 6 –––– Table 7 –––– Table 8 –––– Table 9 –––– Table 10 ––– Table 11 ––– Table 12 ––– Table 13 ––– Table 14 ––– Table 15 ––– Table 16 ––– Table 17 ––– Table 18 ––– Table 19 ––– Table 20 ––– Table 21 ––– Table 22 ––– Table 23 ––– Table 24 ––– Table 25 ––– Table 26 ––– Table 27 ––– Table 28 ––– Table 29 ––– Table 30 ––– Table 31 ––– Table 32 ––– Table 33 ––– Table 34 ––– Table 35 ––– Table 36 ––– Table 37 ––– Table 38 ––– Table 39 ––– Table 40 ––– Table 41 ––– Allied Telesyn MIB Structure ........................................................................1 MIB Parameters Example.............................................................................3 MIB Version Parameters...............................................................................4 IP Interface Parameters................................................................................7 Interface Static Parameters ..........................................................................7 Interface DHCP Parameters .........................................................................8 Interface QoS Parameters ............................................................................8 Interface VLAN Parameters..........................................................................9 Unit Manager Parameters...........................................................................11 Unit Manager Static Parameters.................................................................11 Unit Manager DHCP Parameters ...............................................................12 apaUIMapRulex Group Parameters ...........................................................13 Portn Call Forward Unconditional Parameters ...........................................14 Portn Call Forward Busy Parameters .........................................................15 Portn Call Forward No Answer Parameters................................................15 Gateway Group Basic Parameter ...............................................................17 Gateway Port n Parameters .......................................................................17 Gateway Perm Local Same AC Parameters ..............................................18 Gateway Perm Local Diff AC Parameters ..................................................18 Gateway Perm Long Distance Same AC Parameters ................................19 Gateway Perm Long Distance Different AC Parameters............................19 Gateway Perm Long Distance Different CC Parameters............................20 Country Group Parameters.........................................................................21 Port Parameters..........................................................................................23 DSP Parameters.........................................................................................24 DSP User Gain Parameters........................................................................24 DSP Country Specific Parameter ...............................................................25 DSP Country Specific Gain Parameters .....................................................25 DSP Codec Parameter ...............................................................................25 DSP Codec G711aLaw Parameters ...........................................................26 DSP Codec G711uLaw Parameters ...........................................................26 DSP Codec G723.1 Parameters.................................................................26 DSP Codec G729AB Parameters...............................................................27 DSP Codec T.38 Parameter .......................................................................27 DTMF Parameter ........................................................................................27 Syslog Parameters .....................................................................................29 Syslog Static Parameters ...........................................................................29 Syslog DHCP Parameters ..........................................................................30 tftp Group Parameters ................................................................................31 tftp Server Static Group Parameters...........................................................31 tftp Server DHCP Group Parameters .........................................................32 VP500 Communication Unit vii List of Tables Table 42 Table 43 Table 44 Table 45 Table 46 Table 47 Table 48 Table 49 Table 50 Table 51 Table 52 Table 53 Table 54 Table 55 Table 56 Table 57 Table 58 Table 59 Table 60 Table 61 Table 62 Table 63 Table 64 Table 65 Table 66 Table 67 Table 68 Table 69 Table 70 Table 71 Table 72 Table 73 Table 74 Table 75 Table 76 MIB Reference Manual ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– VP500 Bypass Group Parameters..............................................................33 APA System Group Parameters .................................................................35 APA Cmd Group Parameters .....................................................................37 SNMP Group Parameters...........................................................................39 apaInfoInterface Parameters ......................................................................41 apaInfo TFTP Parameters ..........................................................................41 apaInfo File Config Parameters ..................................................................42 Config Trap Parameters .............................................................................43 SNTP General Parameters.........................................................................45 Static SNTP Parameters.............................................................................45 DHCP SNTP Parameters ...........................................................................46 SNTP Time Zone Parameters ....................................................................46 MGCP MIB Version Parameter...................................................................51 General Parameter .....................................................................................51 End Point Id Parameters.............................................................................52 Call Agent Parameters................................................................................52 Call Agent Static Group ..............................................................................52 Call Agent DHCP Group .............................................................................53 Retransmission Parameters .......................................................................53 Generic Media Package Parameters..........................................................54 DTMF Package Parameters .......................................................................54 Line Package Parameters ..........................................................................55 MGCP Status Parameters ..........................................................................55 MGCP Statistics Parameters ......................................................................56 SIP MIB Version Parameter........................................................................59 sipUA Group Parameters............................................................................59 sipUA Log Group Parameters.....................................................................60 sipUA Log Static Group Parameters...........................................................60 sipUA Log Group DHCP Parameters .........................................................60 sipUA Server Group Parameters ................................................................61 sipUA Server Static Group Parameters ......................................................61 sipUA Log Group Parameters.....................................................................61 sipUAn Group Parameters..........................................................................62 sipUAn AuthGroup Parameters ..................................................................63 sipUA AuthGroup Parameters ....................................................................63 VP500 Communication Unit viii 1 MIB Structure This document lists and explains all parameters in the Allied Telesyn Management Information Base (MIB) structure. A description and possible values are provided to help you make the required changes to your system. Please read the comments very carefully before changing a parameter’s value. What is a MIB? A Management Information Base (MIB) specifies what variables the network elements maintain (the information that can be queried and set by the manager). All variables are identified by object identifiers, a hierarchical naming scheme consisting of long strings of numbers that are normally abbreviated into a simple name, for human readability. A MIB is structured like a tree. At the top of the tree is the most general information available about a network. Each branch of the tree then gets more detailed into a specific network area, with the leaves of the tree as specific as the MIB can get. Allied Telesyn MIB Structure The current MIB structure has three individual MIB files: Table 1: Allied Telesyn MIB Structure MIB Description Provisioning MIB The Provisioning MIB allows you to set up all the parameters related to the VP500 communication unit. The Provisioning MIB contains all the functional parameters the unit uses to operate. All have been configured by default upon start up. MGCP MIB The MGCP MIB is used exclusively with VP500 communication units that run the Media Gateway Control Protocol (MGCP). SIP MIB The SIP MIB is used exclusively with VP500 communication units that run the Session Initiation Protocol (SIP). Figure 1: MIB Structure VP500 Communication Unit 1 Chapter 1 - MIB Structure MIB Reference Manual All parameters in the MIBs have been configured by default upon start up. However, if you need to modify some of these parameters (for example, parameters related to the country in which you are), use a SNMP browser. Note: The AT-VP504E FXO communication units can only run the SIP signaling protocol. Storage Clauses In addition to the standard MIBs clauses, there are two STORAGE clauses for storage purpose: Persistent Volatile Persistent Parameters Persistent parameters are saved into the VP500 communication unit’s memory and restored when the unit is rebooted or restarted. The only way to change the value of a persistent parameter is to manually update it with a SNMP browser or by provisioning a new configuration file. Volatile Parameters Volatile parameters are lost every time the VP500 communication unit is rebooted. This type of parameter includes toggling parameters such as requesting a configuration file or a software download. Statistics are also volatile parameters that are lost every time the unit is rebooted. Changing a Parameter Value Changing a parameter involves contacting the VP500 communication unit with any SNMP MIB browser. You can use the built-in SNMP editor of the Unit Manager. See the IP Communication Server Administration Manual for more details. Be sure that you use the MIB files that match the version of the MIB located inside the current software build of the unit. You must then locate the proper parameter to modify and change its value. Most of the parameters will require that you reboot the VP500 communication unit. A reboot may be software-initiated or manually initiated with the power switch. It will delete all statistics stored and will overwrite all volatile parameter values in the configuration file. A reboot will also reinitiate the entire unit’s initial provisioning sequence. Switching Protocols VP500 Communication Unit The MIB structure contains three MIB files, but only two are actually used at the same time: 2 Chapter 1 - MIB Structure MIB Reference Manual With the SIP signalling protocol: the VP500 communication unit uses the Provisioning MIB and SIP MIB. With the MGCP signalling protocol: the VP500 communication unit uses the Provisioning MIB and MGCP MIB. You can switch between protocols and the proper MIB will be activated upon restart. Note: If you are using AT-VP504E FXO communication units, switching protocol is not possible because these units can only run the SIP signaling protocol. X To switch MIB according to the protocol used: In the general Provisioning MIB, locate the signaling ProtocolsSwitch variable under the signaling ProtocolsGroup. This variable allows you to switch from one protocol to another. Set the signalingProtocolsSwitch variable to 0=MGCP or 1=SIP. The default value is 1=SIP. The VP500 communication unit reboots automatically. After the unit restarts, it will use the selected MIB. For more details, see: Manual Conventions • “Part 2: MGCP MIB” on page 49 • “Part 3: SIP MIB” on page 57 The MIB parameters are presented in a table such as the following: Table 2: MIB Parameters Example Name Access provisionningMibVersion R-O Description MIB version. Default Value: 1.0 Dynamic N/A The tables contain the following information: VP500 Communication Unit Name: Full name of the parameter as displayed in the MIB. Access: The parameter may have one of two access 3 Chapter 1 - MIB Structure MIB Reference Manual types: MIB Version • R/W: the parameter is “Read/Write” and can be edited. • R-O: the parameter is “Read-Only” and cannot be edited. Description: Short description of the parameter as displayed in the MIB. When possible, the default value for the parameter is provided. Dynamic: Describes the update status of the parameter, which can have three update types: • Dynamic (Yes): The parameter value is updated automatically. You do not need to restart the VP500 communication unit. • Not dynamic (No): The parameter value is not updated automatically. You must restart the VP500 communication unit for the change to take effect. • Not Applicable (N/A): Applies to read-only parameters. The following parameters give the current version of the Provisioning MIB and the VP500 communication unit model involved. Table 3: MIB Version Parameters Name Access Description Dynamic provisionningMibVersion R-O MIB version. Default Value: 1.0 N/A analogGatewayID R-O VP500 communication unit model. N/A 0 = APA III-1 1 = APA III-4 FXS 2 = APA III-4 FXO 3 = APA III-4 FXS/FXO Default Value: VP500 Communication Unit 4 Part 1: Provisioning MIB 2 InterfaceGroup Parameters The Interface parameters allow you to set information pertaining to the IP addresses used by the VP500 communication unit. Basic Interface Parameters The basic interface parameters allow you to define the VP500 communication unit’s network “signature”. Table 4: IP Interface Parameters Name Access Description Dynamic interfaceQoSSignalingDSFiledValue R/W Signaling (SIP negociation) QoS Differentiated Services field value. Default Value: 184 Yes interfaceQoSMediaDSFieldValue R/W Media (SIP negociation) QoS Differentiated Services field value. Default Value: 184 Yes interfaceMacAddress R-O VP500 communication unit Ethernet MAC address. Default Value: 0090F8FFFFFF N/A interfaceUseDhcp R/W Select the provenance of the VP500 communication unit network configuration. No 0 = Static 1 = DHCP Default Value: 1 interfaceDhcpServerIp interfaceStaticGroup R-O DHCP server IP address. The field is empty if no DHCP server was found. N/A The following parameters allow you to set static interface information for the VP500 communication unit. Table 5: Interface Static Parameters Name Access Description Dymanic interfaceStaticPrimDnsIp R/W Static primary DNS server IP address. Default Value: 192.168.0.10 No interfaceStaticSecDnsIp R/W Static secondary DNS server IP address. Default Value: 192.168.0.10 No interfaceStaticDefaultRouterIp R/W Static default router IP address. Default Value: 192.168.0.10 No interfaceStaticSubnetMaskIp R/W Static subnet mask. Default Value: 255.255.255.0 No interfaceStaticLocalIp R/W Static local IP address. Default Value: 192.168.0.1 No VP500 Communication Unit 7 Chapter 2 - InterfaceGroup Parameters interfaceDhcpGroup MIB Reference Manual - Provisioning MIB The following parameters allow you to set DHCP information for the VP500 communication unit. Table 6: Interface DHCP Parameters Name Access Description Dynamic interfaceDhcpPrimDnsIp R-O Primary DNS server IP address provided by the DHCP server. Default Value: 192.168.0.10 N/A interfaceDhcpSecDnsIp R-O Secondary DNS server IP address provided by the DHCP server. N/A Default Value: 192.168.0.10 interfaceDhcpDefaultRouterIp R-O Default router IP address provided by the DHCP server. Default Value: 192.168.0.10 N/A interfaceDhcpSubnetMaskIp R-O Subnet mask provided by the DHCP server. Default Value: 255.255.255.0 N/A interfaceDhcpLocalIp R-O Local IP address provided by the DHCP server. Default Value: 192.168.0.1 N/A interfaceQoSThe following parameters allow you to define the 802.1q settings of the Group Parameters VP500 communication unit. Table 7: Interface QoS Parameters Name interfaceQoSSignalingIeee8021QFilterEnable Access R/W Description Enabling IEEE 802.1Q VLAN user priority tagging for VoIP signaling packet. This filter applies to any VoIP signaling protocol in use (e.g. MGCP or SIP). When the filter is disabled (as well as VLAN), no tag is added to the Ethernet header. Otherwise, each signaling packet is tagged with the user priority defined below. Dynamic Yes 0 = Disable 1 = Enable Default Value: 0 interfaceQoSSignalingIeee8021QUserPriority R/W IEEE 802.1Q VLAN user priority value for VoIP signaling packet. This value is used to set the user priority in the TCI field of the VLAN tag. Tagging user priority is applied only when the filter is enabled. In the case where the filter for signaling protocol is disabled and the VLAN option is enabled, the default user priority declared under the VLAN group will be used. Otherwise, the user priority set for signaling has precedence over the VLAN default user priority. • 7 = High priority • 0 = Low priority Default Value: 6 Yes interfaceQoSMediaIeee8021QFilterEnable R/W Enabling IEEE 802.1Q VLAN user priority tagging for VoIP media packet. This filter applies to any VoIP media protocol in use (e.g. RTP, T.38). When the filter is disabled (as well as VLAN), no tag is added to the Ethernet header. Otherwise, each signaling packet is tagged with the user priority defined below. Yes 0 = Disable 1 = Enable Default Value: 0 VP500 Communication Unit 8 Chapter 2 - InterfaceGroup Parameters MIB Reference Manual - Provisioning MIB Table 7: Interface QoS Parameters (Continued) Name Access interfaceQoSMediaIeee8021QUserPriority R/W Description IEEE 802.1Q VLAN user priority value for VoIP media packet. This value is used to set the user priority in the TCI field of the VLAN tag. Tagging user priority is applied only when the filter is enabled. In the case where the filter for signaling protocol is disabled and the VLAN option is enabled, the default user priority declared under the VLAN group will be used. Otherwise, the user priority set for signaling has precedence over the VLAN default user priority. • 7 = High priority • 0 = Low priority Default Value: 6 Dynamic Yes interfaceVlanThe following parameters allow you to define the VLAN settings of the Group Parameters VP500 communication unit. Table 8: Interface VLAN Parameters Name interfaceVlanIeee8021QTaggingEnable Access R/W Description Enabling IEEE 802.1Q VLAN tagging. With this option enabled, all packets are tagged with the Virtual ID (VID) specified below. The default user priority is to be applied in case of general protocol or when signaling or media protocol filtering is disabled.WARNING: Enable this option only on compatible LAN with equipment supporting the VLAN tagging. Otherwise, the Unit may be unreachable. In this case, please use the reset button to access and disable VLAN tagging - in the reset mode, tagging is not permitted. See IEEE 802.1Q for more information on this topic. Dynamic Yes 0 = Disable 1 = Enable Default Value: 0 interfaceVlanIeee8021QVirtualLanID R/W IEEE 802.1Q Virtual LAN ID. This is theVID to be applied in the TCI field when tagging is enabled. The value 1 is the default Port VID (PVID) for bridge port. The 4095 VID (0xFFF) is reserved for implementation use and it shall not be used in tag header.NOTE: As per standard, some bridges may not support the full range of VID. Default Value: 1 Yes interfaceVlanIeee8021QDefaultUserPriority R/W IEEE 802.1Q Virtual LAN default user priority. This is the user priority to be applied in the TCI field when tagging is enabled. This value applies to all protocols for which no priority filtering is enabled (e.g. ARP, ICMP). • 7 = High priority • 0 = Low priority Default Value: 6 Yes VP500 Communication Unit 9 Chapter 2 - InterfaceGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 10 3 apaManager Parameters The apaManager Group parameters allow you to set information pertaining to the Unit Manager, which is a module of the IP Communication Server used to set and provision the VP500 communication units. apaManager Basic The following parameters allow you to define basic information about the Unit Manager the VP500 communication unit will use. Parameters Table 9: Unit Manager Parameters Name Access apaManagerEnable R/W Description Dynamic No Enable the Unit Manager. 0 = Disable 1 = Enable Default Value: 1 apaManagerUseDhcp R/W Select the provenance of the Unit Manager configuration. Yesa 0 = Static 1 = DHCP Default Value: 1 apaManagerTrapRetransmissionPeriod R-W TRAP retransmission period in ms. Default Value: 60000 Yes apaManagerTrapRetransmissionRetryCount R-W TRAP retransmission retry count: • -1 = infinite - always retransmit Default Value: 10 Yes a. Only when at least one of the variables xxUseDhcp was set to 1 before starting the VP500 unit. apaManagerStatic- The following parameters allow you to set static information pertaining to the Unit Manager. Group Table 10: Unit Manager Static Parameters Name Access Description Dynamic apaManagerStaticPrimHost R/W Static Unit Manager IP address or domain name. Default Value: 192.168.0.10 Yes apaManagerStaticPrimTrapPort R/W Static Unit Manager IP port number on which traps must be sent. Default Value: 162 Yes VP500 Communication Unit 11 Chapter 3 - apaManager Parameters apaManagerDhcpGroup MIB Reference Manual - Provisioning MIB The following parameters allow you to set DHCP information for the Unit Manager. Table 11: Unit Manager DHCP Parameters Name Access Description Dynamic apaManagerDhcpVendorSpecificCode R/W DHCP Unit Manager vendor specific code. Default Value: 200 Yes apaManagerDhcpPrimHost R-O Unit Manager IP address or domain name provided by the DHCP server. Default Value: 192.168.0.10 N/A apaManagerDhcpPrimTrapPort R-O Unit Manager IP port number, provided by the DHCP server, on which traps must be sent. Default Value: 162 N/A VP500 Communication Unit 12 4 apaUIGroup Parameters The apaUIGroup parameters allow you to set the various permission settings used when making calls and to set information pertaining to the telephony services. apaUIMapRuleGroup Parameters Note: The Provisioning MIB contains four (4) Dialing Map Rules. The parameter description is identical for each rule. For clarity’s sake, only one generic set of parameters is described in this manual. When browsing through the Provisioning MIB, replace the “x” letter in the following parameters with the proper rule number (from 1 to 4). apaUIMapRulexGroup The following parameters allow you to define Dial Map Rule #n. Table 12: apaUIMapRulex Group Parameters Name apaUIMapRulexEnable Access R/W Description Enable Dial Map Rule #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 1 apaUIMapRulexDialMap R/W Rule #n Dial Map. Default Value: x.T Yes apaUIMapRulexIsValid R-O Rule #n Dial Map validity. N/A 0 = Not valid 1 = Valid Default Value: 0 apaUIMapRulexRemDigitEnable R/W Select if digits must be removed from the dialed number for Dial Map Rule #n. Yes 0 = Disable (do not remove digits) 1 = Enable (remove digits) Default Value: 0 apaUIMapRulexRemDigitCount R/W Number of digits to remove from the dialed number for Dial Map Rule #n. Default Value: 0 Yes apaUIMapRulexPrefixEnable R/W Select if digits must be prefixed to the dialed number for Dial Map Rule #n. Yes 0 = Disable (do not prefix digits) 1 = Enable (prefix digits) Default Value: 1 VP500 Communication Unit 13 Chapter 4 - apaUIGroup Parameters MIB Reference Manual - Provisioning MIB Table 12: apaUIMapRulex Group Parameters (Continued) Name Access apaUIMapRulexPrefixDigit R/W Description Select the digits to prefix to the dialed number for Dial Map Rule #n. Dynamic Yes 0 = Prefix Area code 1 = Prefix Country code 2 = Prefix Country code and Area code Default Value: 2 apaUIServicesGroup Note: The following parameters only apply to access communication units such as the AT-VP504E FXS. apaUIServicesPortnGroup The following parameters allow you to define the services offered by the VP500 communication unit. Note: Each port of the VP500 communication unit has its own set of parameters. The parameter description is identical for each port. For clarity’s sake, only one generic set of parameters is described in this manual. When browsing through the Provisioning MIB, replace the “n” letter in the following parameters with the proper port number (from 1 to 4). apaUIServicesPortnCallForwardUnconditionalGroup Table 13: Portn Call Forward Unconditional Parameters Name apaUIServicesPortnCallForwardUnconditional Enable Access R/W Description Unconditionally enable the Call Forward on port #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 0 apaUIServicesPortnCallForwardUnconditional Address R/W Address to which the phone call will be unconditionally forwarded. Address format = 'userInfo@host:portNumber' where: • userInfo = user name or telephone number (optional) • host = domain name or IP address • portNumber = port number (optional) Default Value: Yes apaUIServicesPortnCallForwardUnconditional EnableStarNumber R/W Digits to dial after the star key to unconditionally enable the Call Forward. Default Value: 25 Yes VP500 Communication Unit 14 Chapter 4 - apaUIGroup Parameters MIB Reference Manual - Provisioning MIB Table 13: Portn Call Forward Unconditional Parameters (Continued) Name Access apaUIServicesPortnCallForwardUnconditional DisableStarNumber R/W Description Digits to dial after the star key to disable the unconditional Call Forward. Default Value: 26 Dynamic Yes apaUIServicesPortnCallForwardBusyGroup Table 14: Portn Call Forward Busy Parameters Name Access apaUIServicesPortnCallForwardBusyEnable R/W Description Enable the Call Forward when busy on port #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 0 apaUIServicesPortnCallForwardBusyAddress R/W Address to which the phone call will be unconditionally forwarded. Address format = 'userInfo@host:portNumber' where: • userInfo = user name or telephone number (optional) • host = domain name or IP address • portNumber = port number (optional) Default Value: Yes apaUIServicesPortnCallForwardNoAnswerGroup Table 15: Portn Call Forward No Answer Parameters Name apaUIServicesPortnCallForwardNoAnswerEn able Access R/W Description Enable the Call Forward on no answer on port #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 0 apaUIServicesPortnCallForwardNoAnswerAd dress R/W Address to which the phone call will be unconditionally forwarded. Address format = 'userInfo@host:portNumber' where: • userInfo = user name or telephone number (optional) • host = domain name or IP address • portNumber = port number (optional) Default Value: Yes apaUIServicesPortnCallForwardNoAnswerNu mberOfRings R/W Number of phone rings before forwarding the incoming call. Default Value: 3 Yes VP500 Communication Unit 15 Chapter 4 - apaUIGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 16 5 gatewayGroup Parameters The gatewayGroup parameters allow you to set the various permission settings used when making calls in gateway mode. Note: The gatewayGroup parameters are used only by gateway units such as the AT-VP504E FXO. gatewayGroup Basic Parameter The following parameter allows you to define the General Dial Prefix to use when making calls. Table 16: Gateway Group Basic Parameter Name gatewayGeneralDialPrefix Access R/W Description Prefix that must be dialed before any other numbers on a port used in FXO mode. Default Value: Dynamic Yes gatewayPortnGroup Note: Each port of the VP500 communication unit has its own set of parameters. The parameter description is identical for each port. For clarity’s sake, only one generic set of parameters is described in this manual. When browsing through the Provisioning MIB, replace the “n” letter in the following parameters with the proper port number (from 1 to 4). The following parameters allow you to set gateway information on Port #n. Table 17: Gateway Port n Parameters Name gatewayPortnPermissionMode Access R/W Description Select port #n configuration used in FXO mode. Dynamic Yes 0 = Net to PSTN 1 = PSTN to Net 2 = Both directions Default Value: 2 VP500 Communication Unit 17 Chapter 5 - gatewayGroup Parameters MIB Reference Manual - Provisioning MIB Table 17: Gateway Port n Parameters (Continued) Name Access gatewayPortnRedirectEnable R/W Description Enable the redirection of incoming calls on port #n used in FXO mode. Dynamic Yes 0 = Disable (IP dial tone) 1 = Enable (Redirected to address gatewayPortxRedirectToAddress) Default Value: 0 gatewayPortnRedirectToAddress gatewayPermLocalSameACGroup R/W Address to which incoming calls on port #n are redirected. Default Value: Yes The following parameters allow you to set gateway permissions when making a Local Call in the same Area Code. Table 18: Gateway Perm Local Same AC Parameters Name Access Description Dynamic gatewayPermLocalSameACPrefix R/W Prefix that must be dialed before the destination number. The field is empty when no prefix is required (the destination call is local with the same area code as countryAreaCode). Default Value: Yes gatewayPermLocalSameACAllowed R/W Semi-colon separated list of numbers allowed to be called on a port used in FXO mode (the destination call is local with the same area code as countryAreaCode). Default Value: Yes gatewayPermLocalSameACAllowAll R/W Select which numbers are allowed to be called on a port used in FXO mode. Yes 0 = Only numbers in field gatewayPermLocalSameACAllowed 1 = All numbers (The destination call is local with the same area code as countryAreaCode) Default Value: 0 gatewayPermLocalDiffACGroup The following parameters allow you to set gateway permissions when making a Local Call in a different Area Code. Table 19: Gateway Perm Local Diff AC Parameters Name Access Description Dynamic gatewayPermLocalDiffACPrefix R/W Prefix that must be dialed before the destination number. The field is empty when no prefix is required (the destination call is local with a different area code than countryAreaCode). Default Value: Yes gatewayPermLocalDiffACAllowed R/W Semi-colon separated list of numbers allowed to be called on port used in FXO mode (the destination call is local with a different area code than countryAreaCode). Default Value: Yes VP500 Communication Unit 18 Chapter 5 - gatewayGroup Parameters MIB Reference Manual - Provisioning MIB Table 19: Gateway Perm Local Diff AC Parameters (Continued) Name Access gatewayPermLocalDiffACAllowAll R/W Description Select which numbers are allowed to be called on port used in FXO mode. Dynamic Yes 0 = Only numbers in field gatewayPermLocalSameACAllowed 1 = All numbers (The destination call is local with a different area code than countryAreaCode) Default Value: 0 gatewayPermThe following parameters allow you to set gateway permissions when LongDistSameAC- making a Long Distance Call in the same Area Code. Group Table 20: Gateway Perm Long Distance Same AC Parameters Name Access Description Dynamic gatewayPermLongDistSameACPrefix R/W Prefix that must be dialed before the destination number. The field is empty when no prefix is required (the destination call is long distance with the same area code as countryAreaCode). Default Value: Yes gatewayPermLongDistSameACAllowed R/W Semi-colon separated list of numbers allowed to be called on port used in FXO mode (the destination call is long distance with the same area code as countryAreaCode). Default Value: Yes gatewayPermLongDistSameACAllowAll R/W Select which numbers are allowed to be called on port used in FXO mode. Yes 0 = Only numbers in field gatewayPermLocalSameACAllowed 1 = All numbers (The destination call is long distance with the same area code as countryAreaCode) Default Value: 0 gatewayPermLongDistDiffACGroup The following parameters allow you to set gateway permissions when making a Long Distance Call in a different Area Code. Table 21: Gateway Perm Long Distance Different AC Parameters Name gatewayPermLongDistDiffACPrefix VP500 Communication Unit Access R/W Description Prefix that must be dialed before the destination number. The field is empty when no prefix is required (The destination call is long distance with a different area code than countryAreaCode). Default Value: Dynamic Yes 19 Chapter 5 - gatewayGroup Parameters MIB Reference Manual - Provisioning MIB Table 21: Gateway Perm Long Distance Different AC Parameters (Continued) Name Access Description Dynamic gatewayPermLongDistDiffACAllowed R/W Semi-colon separated list of numbers allowed to be called on port used in FXO mode (the destination call is long distance with a different area code than countryAreaCode). Default Value: Yes gatewayPermLongDistDiffACAllowAll R/W Select which numbers are allowed to be called on port used in FXO mode. Yes 0 = Only numbers in field gatewayPermLocalSameACAllowed 1 = All numbers (The destination call is long distance with a different area code than countryAreaCode) Default Value: 0 gatewayPermLongDistDiffCCGroup The following parameters allow you to set gateway permissions when making a Long Distance Call in a different country. Table 22: Gateway Perm Long Distance Different CC Parameters Name Access Description Dynamic gatewayPermLongDistDiffCCPrefix R/W Prefix that must be dialed before the destination number. The field is empty when no prefix is required (the destination call is long distance with a different country code than countryCountryCode). Default Value: Yes gatewayPermLongDistDiffCCAllowed R/W Semi-colon separated list of numbers allowed to be called on port used in FXO mode (the destination call is long distance with a different country code than countryCountryCode). Default Value: Yes gatewayPermLongDistDiffCCAllowAll R/W Select which numbers are allowed to be called on port used in FXO mode. Yes 0 = Only numbers in field gatewayPermLocalSameACAllowed 1 = All numbers (The destination call is long distance with a different country code than countryCountryCode). Default Value: 0 VP500 Communication Unit 20 6 countryGroup Parameters The Country Group parameters allow you to set information pertaining to the physical location of the VP500 communication unit. Country Parameters The country parameters allow you to define information that will be used when dialing. Table 23: Country Group Parameters Name Access Description Dynamic countryCountryCode R/W Country code associated to the current location of the VP500 communication unit. Default Value: 1 Yes countryAreaCode R/W Area code associated to the current location of the VP500 communication unit. Default Value: 819 Yes countrySelection R/W Select the default country that may be used for configuration. No 0 = Use Custom Configuration 1 = North America 1 2 = North America 2 3 = Austria 4 = France 5 = Germany 1 6 = Germany 2 7 = UK 8 = Italy 9 = Spain 10 = Switzerland 11 = Sweden 12 = Australia 13 = Japan Default Value: 1 countryForceConfiguration R/W If the value is set to 1, every custom configuration selection will be overridden by the selected country configuration in countrySelection. No 0 = Do not override 1 = Override any custom configuration selection Default Value: 1 VP500 Communication Unit 21 Chapter 6 - countryGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 22 7 portGroup Parameters The Port Group parameters allow you to set information pertaining to the four ports of the VP500 communication unit. General Parameters Note: Each port of the VP500 communication unit has its own set of parameters. The parameter description is identical for each port. For clarity’s sake, only one generic set of parameters is described in this manual. When browsing through the Provisioning MIB, replace the “n” letter in the following parameters with the proper port number (from 1 to 4). The following parameters allow you to set port information for the VP500 communication unit. Table 24: Port Parameters Name portnEnable Access R/W Description Enable VP500 communication unit port #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 1 portnAnalogLineType R/W The analog telephone line type parameter defines the type of analog line used. Ground Start ensures proper Far End Disconnect between an FXO port and the PSTN. No 0 = Loop Start 1 = Ground Start Default Value: 0 portnType R-O Port #n mode in use. N/A 0 = FXS 1 = FXO Default Value: 0 portnConfigurationMode R/W Select the port mode to be used if port #n is a dual function port. No 0 = FXS 1 = FXO Default Value: 0 portSilenceDetectionMode R/W Options for silence detection. No 0 = Disable 1 = Disconnect if silence detected on SCN side 2 = Disconnect if silence detected on IP side 3 = Disconnect only when both sides have become silent Default Value: 0 VP500 Communication Unit 23 Chapter 7 - portGroup Parameters MIB Reference Manual - Provisioning MIB Table 24: Port Parameters (Continued) Name Access Description Dynamic portSilenceDetectionTimeout R/W When silence is detected on the line, period of silent time after which the line is hanged up. 300 seconds = 5 minutes. Values range from 0 to 300 seconds. Default Value: 300 No portForcedEndOfCallEnable R/W Enable call interruption if unsuccessfull. No 0 = Disable 1 = Enable Default Value: 1 portForcedEndOfCallTimeout portnDspGroup R/W Forced end of call timeout in seconds. Values range from 0 to 180 seconds. Default Value: 30 No The following parameters allow you to set DSP parameters. Table 25: DSP Parameters Name Access Description Dynamic portnDspMaxJitterBufferLen R/W Port #n maximum jitter buffer length in ms. Default Value: 150 No portnDspTargetJitterBufferLen R/W Port #n target jitter buffer length in ms. Default Value: 50 No portnDspAdaptativityJitterBuffer R/W Port #n adaptative jitter buffer. No 0 = OFF 1 = ON Default Value: 1 portnDspVoiceActivityDetection R/W Port #n Voice Activity Detection (VAD). No 0 = OFF 1 = Transparent 2 = Conservative Default Value: 2 portnDspEchoCancelControl R/W Port #n echo cancel control. No 0 = OFF 1 = ON Default Value: 1 portnDspUserGainGroup Table 26: DSP User Gain Parameters Name portnDspUserGainInputOffset VP500 Communication Unit Access R/W Description Port #n user input gain offset in dB. Default Value: -6 Dynamic No 24 Chapter 7 - portGroup Parameters MIB Reference Manual - Provisioning MIB Table 26: DSP User Gain Parameters (Continued) Name Access portnDspUserGainOutputOffset R/W Description Port #n user output gain offset in dB. Default Value: -6 Dynamic No portnDspCountrySpecificGroup Table 27: DSP Country Specific Parameter Name Access portnDspCountrySpecificLoopCurrent R/W Description Port #n country specific loop current. Default Value: 30 Dynamic No portnDspCountrySpecificGainGroup Table 28: DSP Country Specific Gain Parameters Name Access portnDspCountrySpecificGainConfiguration R/W Description Select port #n country specific gain configuration. Dynamic No 0 = Use custom configuration 1 = Use default country configuration Default Value: 1 portnDspCountrySpecificGainBaseInput R/W Port #n country specific base input gain. Default Value: 3648 No portnDspCountrySpecificGainBaseOutput R/W Port #n country specific base output gain. Default Value: 3029 No portnDspCountrySpecificGainBaseInputOffset R/W Port #n coutry specific base input gain offset in dB. Default Value: 0 No portnDspCountrySpecificGainBaseOutputOffs et R/W Port #n country specific base output gain offset in dB. Default Value: 0 No portnDspCodecGroup Table 29: DSP Codec Parameter Name portnDspPreferredCodec Access R/W Description Select preferred port #n codec. Dynamic Yes 0 = G.711 u-Law (PCMU) 1 = G.711 a-Law (PCMA) 2 = G.723.1 3 = G.729.AB Default Value: 0 VP500 Communication Unit 25 Chapter 7 - portGroup Parameters MIB Reference Manual - Provisioning MIB portnDspCodecG711aLawGroup Table 30: DSP Codec G711aLaw Parameters Name Access portnDspCodecG711aLawEnable R/W Description Enable G.711 a-Law (PCMA) on Port #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 1 portnDspCodecG711aLawPTimeMin R/W Port #n minimum packetization time (ptime) for PCMA in ms. Default Value: 20 Yes portnDspCodecG711aLawPTimeMax R/W Port #n maximum packetization time (ptime) for PCMA in ms. Default Value: 80 Yes portnDspCodecG711uLawGroup Table 31: DSP Codec G711uLaw Parameters Name Access portnDspCodecG711uLawEnable R/W Description Enable G.711 u-Law (PCMU) on Port #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 1 portnDspCodecG711uLawPTimeMin R/W Port #n minimum packetization time (ptime) for PCMU in ms. Default Value: 20 Yes portnDspCodecG711uLawPTimeMax R/W Port #n maximum packetization time (ptime) for PCMU in ms. Default Value: 80 Yes portnDspCodecG7231Group Table 32: DSP Codec G723.1 Parameters Name portnDspCodecG7231Enable Access R/W Description Enable G.723.1 on Port #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 1 portnDspCodecG7231PTimeMin R/W Port #n minimum packetization time (ptime) for G.723.1 in ms. Default Value: 30 Yes portnDspCodecG7231PTimeMax R/W Port #n maximum packetization time (ptime) for G.723.1 in ms. Default Value: 30 Yes portnDspCodecG7231BaudRate R/W Port #n baud rate value for G.723.1. Yes 0 = 6.3Kbps 1 = 5.3Kbps Default Value: 0 VP500 Communication Unit 26 Chapter 7 - portGroup Parameters MIB Reference Manual - Provisioning MIB portnDspCodecG729ABGroup Table 33: DSP Codec G729AB Parameters Name portnDspCodecG729ABEnable Access R/W Description Enable G.729.AB on Port #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 1 portnDspCodecG729ABPTimeMin R/W Port #n minimum packetization time (ptime) for G.729.AB in ms. WARNING: Valid values are 10, 20, 30, and 40. The default value is used if the value is invalid. Default Value: 10 Yes portnDspCodecG729ABPTimeMax R/W Port #n maximun packetization time (ptime) for G.729.AB in ms. WARNING: Valid values are 10, 20, 30, and 40. The default value is used if the value is invalid. Default Value: 10 Yes portnDspCodecT38Group Table 34: DSP Codec T.38 Parameter Name portnDspCodecT38Enable Access R/W Description Enable T.38 on Port #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 1 portnDtmfGroup The following parameter allow you to set DTMF Transport type. Table 35: DTMF Parameter Name portnDtmfTransport Access R/W Description Attribute to select the type of DTMF transport. Dynamic N/A 0 = In band 1 = Out-of-Band using Signaling Protocol 2 = Out-of-Band using RTP DTMF payload Default Value: 2 VP500 Communication Unit 27 Chapter 7 - portGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 28 8 syslogGroup Parameters The Syslog Group parameters allow you to set information pertaining to the Syslog daemon. syslogGroup Basic Parameters The following parameters allow you to set basic information pertaining to the Syslog daemon. Table 36: Syslog Parameters Name syslogMsgEnable Access R/W Description Enable the syslog daemon messages. Dynamic Yes 0 = Disable 1 = Enable Default Value: 1 syslogTracingMask R/W Yes Select the syslog mask: 0 = Absolutely no Tracing 1 = Critical errors 2 = Error conditions 3 = Warning conditions 4 = Informational messages 5 = Debug-level messages (use with care) Higher level mask include lower level masks. e.g.: Error conditions (2) include Critical errors (1) Default Value: 4 syslogUseDhcp R/W Select the provenance of the Syslog configuration. Yesa 0 = Static 1 = DHCP Default Value: 1 a. Only when at least one of the variables xxUseDhcp was set to 1 before starting the VP500 unit. syslogStaticGroup The following parameters allow you to set static information pertaining to the Syslog daemon. Table 37: Syslog Static Parameters Name Access Description Dynamic syslogStaticHost R/W Static Syslog server IP address or domain name. Default Value: 192.168.0.10 Yes syslogStaticPort R/W Static Syslog server IP port number. Default Value: 514 Yes VP500 Communication Unit 29 Chapter 8 - syslogGroup Parameters syslogDhcpGroup MIB Reference Manual - Provisioning MIB The following parameters allow you to set DHCP information for the Syslog daemon. Table 38: Syslog DHCP Parameters Name Access Description Dynamic syslogDhcpVendorSpecificCode R/W DHCP Syslog server vendor specific code. Default Value: 110 Yes syslogDhcpHost R-O Syslog server IP address or domain name provided by the DHCP Server. Default Value: 192.168.0.10 N/A syslogDhcpPort R-O Syslog server IP port number provided by the DHCP server. Default Value: 514 N/A VP500 Communication Unit 30 9 tftpGroup Parameters The TFTP Group parameters allow you to set up the VP500 communication unit with the information pertaining to the server on which the software update is located. tftpGroup Basic Parameters The following parameters allow you to set basic information on the software update server. Table 39: tftp Group Parameters Name Access Description Dynamic tftpFileName R/W VP500 communication unit software file name to download from TFTP server. Default Value: apa.bin Yes tftpEmergencyFileName R/W Emergency VP500 communication unit software file name to download when the Rescue application starts. Default Value: apa_emergency.bin Yes tftpUseDhcp R/W Select the provenance of the TFTP server configuration. Yesa 0 = Static 1 = DHCP Default Value: 1 tftpTimeOut R/W Connection time-out value. Default Value: 30 Yes tftpBlockSize R/W Default block size. Default Value: 1024 Yes tftpDownloadStatus R-O TFTP VP500 communication unit software file download status. N/A 0 = Idle 1 = Success 2 = Fail 3 = In Progress 4 = Abort Default Value: 0 a. Only when at least one of the variables xxUseDhcp was set to 1 before starting the VP500 unit. tftpServerStaticGroup The following parameters allow you to set static information on the TFTP server. Table 40: tftp Server Static Group Parameters Name Access Description Dynamic tftpServerStaticHost R/W Static TFTP server IP address or domain name. Default Value: 192.168.0.10 Yes tftpServerStaticPort R/W Static TFTP server IP port number. Default Value: 69 Yes VP500 Communication Unit 31 Chapter 9 - tftpGroup Parameters MIB Reference Manual - Provisioning MIB Table 40: tftp Server Static Group Parameters (Continued) Name Access Description Dynamic tftpServerStaticEmergencyHost R/W Static emergency TFTP server IP address or domain name. Default Value: 192.168.0.10 Yes tftpServerStaticEmergencyPort R/W Static emergency TFTP server IP port number. Default Value: 69 Yes tftpServerDhcpGroup The following parameters allow you to set DHCP information on the TFTP server. Table 41: tftp Server DHCP Group Parameters Name Access Description Dynamic tftpServerDhcpVendorSpecificCode R/W DHCP TFTP server vendor specific code. Default Value: 117 Yes tftpServerDhcpHost R-O TFTP server IP address or domain name provided by the DHCP server. Default Value: 192.168.0.10 N/A tftpServerDhcpPort R-O TFTP server IP port number provided by the DHCP server. Default Value: 69 N/A tftpServerDhcpEmergencyVendorSpecificCod e R/W DHCP emergency TFTP server vendor specific code. Default Value: 118 Yes tftpServerDhcpEmergencyHost R-O Emergency TFTP server IP address or domain name provided by the DHCP server. Default Value: 192.168.0.10 N/A tftpServerDhcpEmergencyPort R-O Emergency TFTP server IP port number provided by the DHCP server. Default Value: 69 N/A VP500 Communication Unit 32 10 apaByPassGroup Parameters The APA Bypass Group is used to set information on the System Failure Bypass line connector, which is used as an emergency line in case of power or LAN failure. apaByPassGroup Parameters The following parameters are used to set up the behavior of the Bypass connector. Table 42: VP500 Bypass Group Parameters Name apaByPassModeAlwaysEnable Access R/W Description Always enable VP500 communication unit bypass mode. Dynamic Yes 0 = Disable 1 = Enable Default Value: 0 apaByPassModeLanFailEnable R/W Enable VP500 communication unit bypass mode on a LAN failure. Yes 0 = Disable 1 = Enable Default Value: 0 apaByPassModeServerFailEnable R/W Enable VP500 communication unit bypass mode on a server connection failure. Yes 0 = Disable 1 = Enable Default Value: 0 VP500 Communication Unit 33 Chapter 10 - apaByPassGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 34 11 apaSystemGroup Parameters The APA System Group parameters are used to report on the current status of the VP500 communication unit. apaSystemGroup Parameters The following parameters report in the current VP500 communication unit status. Table 43: APA System Group Parameters Name apaSystemOperationalStatusConfigFile Access R-O Description TFTP system operational configuration file download status. Dynamic N/A 0 = Idle 1 = Success 2 = Fail 3 = In Progress 4 = Listening Default Value: 0 apaSystemLastRomCheck R-O Last ROM check status. N/A 0 = Fail 1 = Success Default Value: 0 apaSystemLastRamCheck R-O Last RAM check status. • -1 = Not tested • 0 = Fail • 1 = Success Default Value: -1 N/A apaSystemHardwareVersion R-O VP500 communication unit hardware version. Default Value: rev .X N/A apaSystemSoftwareVersion R-O VP500 communication unit software version. Default Value: 0.0.0.0 N/A VP500 Communication Unit 35 Chapter 11 - apaSystemGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 36 12 apaCmdGroup Parameters The APA Command Group parameters are used to initiate tasks on the VP500 communication unit. apaCmdGroup Parameters The following tasks can be initiated. Table 44: APA Cmd Group Parameters Name apaCmdStartTelnetBenchTest Access R/W Description Instruct the VP500 communication unit to reboot in Telnet bench test mode. Dynamic Yes 0 = Off 1 = On Default Value: 0 apaCmdMode R/W Not implemented ... for future use only. Select the VP500 communication unit command mode. Yes 0 = Enable the VP500 communication unit 1 = Disable the VP500 communication unit 2 = ReEnable the VP500 communication unit 3 = Abrupt Restart (software reset immediately) 4 = Graceful Restart (software reset when all calls have terminated) 5 = Abrupt Shutdown (harware reset immediately) 6 = Graceful Shutdown (harware reset when all calls have terminated) 7 = Reset all statistics 8 = Other Default Value: apaCmdConfigurationMode R/W Select the VP500 communication unit configuration mode. • -1 = Request and wait for the Config File. When the mode is set to -1, a Config File Trap Info is sent to the apaManager to request a config file upload. The value is set back to 0 after the file is received. NOTE: The mode must be set to 1 to apply any new setting. • 0 = Record any changes (TFTP or SNMP) Changes are recorded but won't be applied until the mode is set back to Commit. • 1 = Commit all changes - In this mode changes are automatically applied. NOTE: Some changes may require to reboot the system to take effect. • 2 = Undo all recorded changes - All changes recorded will be dismissed. The mode is set back to 1 afterward. Default Value: -1 Yes apaCmdCheckRom R/W Check the validity of the ROM. Yes 0 = Off 1 = On Default Value: 0 VP500 Communication Unit 37 Chapter 12 - apaCmdGroup Parameters MIB Reference Manual - Provisioning MIB Table 44: APA Cmd Group Parameters (Continued) Name apaCmdCheckRam Access R/W Description Check the validity of the RAM. Dynamic Yes 0 = Off 1 = On Default Value: 0 apaCmdDownloadSoftware R/W Instruct the VP500 communication unit to download a file from TFTP server. Yes 0 = Off 1 = On Default Value: 0 apaCmdRestart R/W Instruct the VP500 communication unit to reboot. Yes 0 = Off 1 = On Default Value: 0 apaCmdRequestConfiguration R/W Select how the VP500 communication unit should request configuration. Yes 0 = Do not need to transfer the Config File 1 = Request the Config File through TFTP Default Value: 1 VP500 Communication Unit 38 13 snmpGroup Parameters The SNMP Group parameters allow you to set information pertaining to the SNMP protocol. snmpGroup Parameters The following parameters allow you to define the SNMP settings of the VP500 communication unit. Table 45: SNMP Group Parameters Name Access Description Dynamic snmpAgentPort R/W SNMP Agent port number on which the unit must listen for SNMP requests. Default Value: 161 No snmpSystemDescription R/W A textual description of the entity. This value should include the full name and version identification of the system’s hardware type, software operating system, and networking software. Yes snmpSystemObjectID R/W The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining “what kind of box” is being managed. For example, if vendor “Flintstones, Inc.” was assigned the subtree 1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its “Fred Router”. Default Value: 1.3.6.1.4.1.4935.1.1.1.1 Yes snmpSystemContact R/W The textual identification of the contact person for this managed node, together with information on how to contact this person. If no contact information is known, the value is the zero-length string. Yes snmpSystemName R/W An administratively-assigned name for this managed node. By convention, this is the node’s fully-qualified domain name. If the name is unknown, the value is the zero-length string. Yes snmpSystemLocation R/W The physical location of this node (e.g., “telephone closet, 3rd floor”). If the location is unknown, the value is the zero-length string. Yes snmpSystemService R/W A value which indicates the set of services that this entity may potentially offer. The value is a sum. This sum initially takes the value zero, Then, for each layer, L, in the range 1 through 7, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. For example, a node which performs only routing functions would have a value of 4 (2^(3-1)). In contrast, a node which is a host offering application services would have a value of 72 (2^(4-1) + 2^(7-1)). Note that in the context of the Internet suite of protocols, values should be calculated accordingly: Yes layer functionality 1 physical (e.g., repeaters) 2 datalink/subnetwork (e.g., bridges) 3 internet (e.g., supports the IP) 4 end-to-end (e.g., supports the TCP) 7 applications (e.g., supports the SMTP) For systems including OSI protocols, layers 5 and 6 may also be counted. Default Value: 72 VP500 Communication Unit 39 Chapter 13 - snmpGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 40 14 apaInfoGroup Parameters The APA Info Group gives read-only information on all the various information used by the VP500 communication unit. apaInfoInterface Parameters The following parameters allow you to see information pertaining to the VP500 communication unit interface. Table 46: apaInfoInterface Parameters Name Access Description Dynamic apaInfoInterfacePrimDnsIpAddress R-O Primary DNS server IP address. Default Value: 192.168.0.10 N/A apaInfoInterfaceSecDnsIpAddress R-O Secondary DNS server IP address. Default Value: 192.168.0.10 N/A apaInfoInterfaceDefaultRouterIpAddress R-O Default router IP address. Default Value: 192.168.0.10 N/A apaInfoInterfaceSubnetMask R-O Subnet mask. Default Value: 255.255.255.0 N/A apaInfoInterfaceIpAddress R-O Local IP Adrress. Default Value: 192.168.0.1 N/A apaInfoTftpGroup The following parameters allow you to see information pertaining to the software download process. Table 47: apaInfo TFTP Parameters Name apaInfoTftpWhoProvide Access R-O Description Provenance of the TFTP server configuration. Dynamic N/A 0 = Static 1 = DHCP Default Value: 1 apaInfoTftpFileName R-O VP500 communication unit software file name to download from TFTP server. Default Value: apa.bin N/A apaInfoTftpIpAddress R-O TFTP server IP address. Default Value: 192.168.0.10 N/A apaInfoTftpPort R-O TFTP server IP port number. Default Value: 69 N/A VP500 Communication Unit 41 Chapter 14 - apaInfoGroup Parameters MIB Reference Manual - Provisioning MIB apaInfoFileConfig- The following parameters allow you to see information pertaining to the VP500 communication unit’s configuration file. Group Table 48: apaInfo File Config Parameters Name Access Description Dynamic apaInfoFileConfigFileName R-O Configuration File name to download from the TFTP Server. Default Value: sip.cfg N/A apaInfoFileConfigFileVersion R-O Configuration File version to download from the TFTP Server. Default Value: 0 N/A apaInfoFileConfigFileStatus R-O TFTP system operational config file download status. N/A 0 = Idle 1 = Success 2 = Fail 3 = In Progress 4 = Listening Default Value: 0 VP500 Communication Unit 42 15 configTrapGroup Parameters This chapter describes the traps messages that can be sent from the VP500 communication unit to the Unit Manager. Config Trap Parameters The Trap Info parameters give you information on the traps (messages) sent from the VP500 communication unit to the Unit Manager. Table 49: Config Trap Parameters Name Access Description Dynamic configTrapApaConfigInformation N/A The Unit Manager is trapped with the SIP Analog Gateway ID, the MAC address and the request configuration of the VP500 communication unit (the unit requests a configuration from the Unit Manager). N/A configTrapApaStatusInformation N/A The Unit Manager is trapped with the MAC address and the configuration mode of the VP500 communication unit (the unit confirms its configuration mode modification). N/A configTrapApaStatusConfigFile N/A The Unit Manager is trapped with the MAC address and the config file download status. N/A VP500 Communication Unit 43 Chapter 15 - configTrapGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 44 16 sntpGroup Parameters This chapter describes the SNTP settings that can be set on the VP500 communication unit. General Parameters The general SNTP parameters allow you to enable and synchronize the SNTP feature. Table 50: SNTP General Parameters Name sntpEnable Access R/W Description Enable SNTP Client. Dynamic Yes 0 = Disable 1 = Enable Default Value: 0 sntpSynchronizationPeriod R/W Interval in minutes before sending a SNTP time request to the SNTP server. Values range from 2 to 1440 seconds. Default Value: 1440 Yes sntpSynchronizationPeriodOnError R/W Interval in minutes before sending a SNTP time request to the SNTP server after an SNTP error. Values range from 1 to 60 minutes. Default Value: 60 Yes sntpUseDhcp R/W Select the provenance of the SNTP Server network configuration. Yesa 0 = Static 1 = Dhcp Default Value: 0 a. Only when at least one of the variables xxUseDhcp was set to 1 before starting the VP500 unit. sntpStaticGroup Parameters The following parameters allow you to set static SNTP information for the VP500 communication unit Table 51: Static SNTP Parameters Name Access Description Dynamic sntpStaticHost R/W Static SNTP server IP address or domain name. Default Value: 192.168.0.10 Yes sntpStaticPort R/W Static SNTP server IP port number. Default Value: 123 Yes VP500 Communication Unit 45 Chapter 16 - sntpGroup Parameters sntpDhcpGroup Parameters MIB Reference Manual - Provisioning MIB The following parameters allow you to set DHCP information for the VP500 communication unit Table 52: DHCP SNTP Parameters Name Access Description Dynamic sntpDhcpVendorCodeSpecific R/W DHCP SNTP server vendor specific code. Default Value: 208 Yes sntpDhcpHost R-O SNTP servers IP address or domain name provided by DHCP server. Default Value: 192.168.0.10 No sntpDhcpPort R-O SNTP server IP port number provided by DHCP server. Default Value: 123 No sntpTimeZoneConfigGroup Parameters The following parameters allow you to set TIme Zone parameters for the VP500 communication unit Table 53: SNTP Time Zone Parameters Name sntpTimeZoneUseTimeZoneSelection Access R/W Description Enable the use of pre-configured time zone selection available. Dynamic Yes 0 = Use custom time zone configuration 1 = Use pre-configured time zone selection Default Value: 1 sntpTimeZoneTimeZoneSelection R/W Pre-configured time zone selection. NOTE: The clock is automatically adjusted for daylight saving time changes if applicable. Yes 0 = Pacific Time (Canada & US) (GMT - 8h) 1 = Mountain Time (Canada & US) (GMT - 7h) 2 = Central Time (Canada & US) (GMT - 6h) 3 = Eastern Time (Canada & US) (GMT - 5h) 4 = Atlantic Time (Canada) (GMT - 4h) 5 = GMT Standard Time 6 = W. Europe Standard Time (GMT + 1h) 7 = China Standard Time (GMT + 8h) 8 = Tokyo Standard Time (GMT + 9h) 9 = Central Australia Standard Time (GMT + 9h30) 10 = Australia Eastern Standard Time (GMT + 10h) Default Value: 1 sntpTimeZoneCustomTimeZoneConfiguration VP500 Communication Unit R/W Custom time zone configuration POSIX strings. Default Value: EST5DST4,M4.1.0/02:00:00,M10.5.0/02:00:00 Yes 46 Chapter 16 - sntpGroup Parameters MIB Reference Manual - Provisioning MIB Table 53: SNTP Time Zone Parameters (Continued) Name sntpTimeZoneCustomTimeZoneIsValid Access R-O Description Validate custom time zone entered. Dynamic N/A 0 = Not valid. 1 = Valid. Default Value: 0 VP500 Communication Unit 47 Chapter 16 - sntpGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 48 Part 2: MGCP MIB 17 mgcpConfiguration Parameters The MGCP Configuration parameters allow you to set information exclusive to VP500 communication units that run the Media Gateway Control Protocol (MGCP). Introduction The MGCP MIB is used with VP500 communication units that run the Media Gateway Control Protocol (MGCP). Table 54: MGCP MIB Version Parameter Name Access mgcpMibVersion R-O Description MIB version. Dynamic N/A X To use the MGCP MIB In the general Provisioning MIB, locate the signalingProtocolsSwitch variable under the signalingProtocolsGroup. This variable allows you to switch from one protocol to another. Set the signalingProtocolsSwitch variable to 0=MGCP. Reboot the VP500 communication unit. After the VP500 communication unit restarts, it will use the MGCP MIB. General Parameter The following parameter allows you to set the UDP port number. Table 55: General Parameter Name mgcpConfigurationResidentialGatewayPort Number VP500 Communication Unit Access R/W Description MGCP Residential Gateway UDP port number. This is the UDP port number on which the unit is listening for any MGCP request. Default Value: 2427 Dynamic No 51 Chapter 17 - mgcpConfiguration Parameters mgcpConfigurationEpIdGroup MIB Reference Manual - MGCP MIB The following parameters allow you to set information pertaining to endpoints. Table 56: End Point Id Parameters Name Access Description Dynamic mgcpConfigurationEpIdLocalNameTerm1 R/W String that specifies the term of the endpoint name. Default Value: aaln No mgcpConfigurationEpIdGatewayFqdnUseDns R/W Select the provenance of the Fully Qualified Domain Name (FQDN). No 0 = Static 1 = DNS Default Value: 0 mgcpConfigurationEpIdStaticGatewayFqdn mgcpConfigurationCallAgentGroup R/W Static Fully Qualified Domain Name (FQDN) of the unit. No The following parameters allow you to set information pertaining to call agents. Table 57: Call Agent Parameters Name Access mgcpConfigurationCallAgentUseDhcp R/W Description Select the provenance of the Call Agent configuration. Dynamic No 0 = Static 1 = DHCP Default Value: 1 mgcpConfigurationCallAgentStaticGrou p Table 58: Call Agent Static Group Name Access Description Dynamic mgcpConfigurationCallAgentStaticPrimary Address R/W Primary static Call Agent address. Can be a dotted IP string or a FQDN address. Default Value: 192.168.0.10 No mgcpConfigurationCallAgentStaticPrimary PortNumber R/W Primary static Call Agent UDP port number. Default Value: 2727 No mgcpConfigurationCallAgentStaticSecondary Address R/W Secondary static Call Agent address. Can be a dotted IP string or a FQDN address. Default Value: 192.168.0.10 No mgcpConfigurationCallAgentStaticSecondary PortNumber R/W Secondary static Call Agent UDP port number. Default Value: 2727 No VP500 Communication Unit 52 Chapter 17 - mgcpConfiguration Parameters MIB Reference Manual - MGCP MIB mgcpConfigurationCallAgentDhcpGrou p Table 59: Call Agent DHCP Group Name Access Description Dynamic mgcpConfigurationCallAgentDhcpPrimary VendorSpecificCode R/W DHCP primary Call Agent vendor specific code. Default Value: 206 No mgcpConfigurationCallAgentDhcpPrimary Address R-O Primary Call Agent address provided by DHCP server. Can be a dotted IP string or a FQDN address. Default Value: 192.168.0.10 N/A mgcpConfigurationCallAgentDhcpPrimaryPort Number R-O Primary Call Agent UDP port number provided by DHCP server. Default Value: 2727 N/A mgcpConfigurationCallAgentDhcpSecondary VendorSpecificCode R/W DHCP secondary Call Agent vendor specific code. Default Value: 207 No mgcpConfigurationCallAgentDhcpSecondary Address R-O Secondary Call Agent address provided by DHCP server. Can be a dotted IP string or a FQDN address. Default Value: 192.168.0.10 N/A mgcpConfigurationCallAgentDhcpSecondary PortNumber R-O Secondary Call Agent UDP port number provided by DHCP server. Default Value: 2727 N/A mgcpConfigurationRetransmissionGroup The following parameters allow you to set retransmission information. Table 60: Retransmission Parameters Name mgcpConfigurationRetransmissionAlgorithm Access R/W Description Retransmission algorith: Dynamic No 0 = static 1 = exponential 2 = exponential with jitter Default Value: 2 mgcpConfigurationRetransmissionInitial Period R/W Retransmission initial period in ms. Default Value: 1000 No mgcpConfigurationRetransmissionMaxPeriod R/W Retransmission maximum period in ms. No 0 = No maximum Default Value: 30000 mgcpConfigurationRetransmissionTimeout R/W Retransmission timeout in seconds. • -1 = infinite - always retransmit • 0 = none - never retransmit Default Value: 30 No mgcpConfigurationRetransmissionRetryCount R/W Retransmission retry count. • -1 = infinite - always retransmit Default Value: 30 No VP500 Communication Unit 53 Chapter 17 - mgcpConfiguration Parameters MIB Reference Manual - MGCP MIB Table 60: Retransmission Parameters (Continued) Name Access mgcpConfigurationRetransmissionRsipInitial Delay R/W Description Delay in ms since the last RSIP to wait before sending the first RSIP for a new endpoint that wants to register. This is to avoid restart avalanche. Dynamic No 0 = Send immediately Default Value: 0 mgcpConfigurationGenericMediaPackageGroup The following parameters allow you to set information pertaining to the generic media package. Table 61: Generic Media Package Parameters Name Access Description Dynamic mgcpConfigurationGenericMediaPackageRt Duration R/W Ring back tone timeout value in ms. Default Value: 180000 No mgcpConfigurationGenericMediaPackageRbk Duration R/W Ring back on connection tone timeout value in ms. Default Value: 180000 No mgcpConfigurationDtmfPackageGroup The following parameters allow you to set information pertaining to the DTMF package. Table 62: DTMF Package Parameters Name Access Description Dynamic mgcpConfigurationDtmfPackageDefaultDigit Map R/W The default Digit Map to apply. Default Value: 0-9T No mgcpConfigurationDtmfPackageInterdigit TimerShortDuration R/W If the gateway can't determine when the final digit is occured, the timer value is set to a short duration. • -1 = infinite • 0 = none Default Value: 4000 No mgcpConfigurationDtmfPackageInterdigit TimerLongDuration R/W If the gateway can determine when the final digit has occured, the timer value is set to a long duration. • -1 = infinite • 0 = none Default Value: 16000 No VP500 Communication Unit 54 Chapter 17 - mgcpConfiguration Parameters mgcpConfigurationLinePackageGroup MIB Reference Manual - MGCP MIB The following parameters allow you to set information pertaining to the line package. Table 63: Line Package Parameters Name Access Description Dynamic mgcpConfigurationLinePackageBzDuration R/W Busy tone timeout value in ms. Default Value: 30000 No mgcpConfigurationLinePackageDlDuration R/W Dial tone timeout value in ms. Default Value: 16000 No mgcpConfigurationLinePackageRgDuration R/W Ring tone timeout value in ms. Default Value: 180000 No mgcpConfigurationLinePackageSlDuration R/W Stutter dial tone timeout value in ms. Default Value: 16000 No mgcpConfigurationLinePackageOtDuration R/W Off hook warning tone timeout value in ms. Default Value: 65535000 No mgcpStatusGroup Parameters The MGCP Status parameters represent the actual status of the Media Gateway Control Protocol (MGCP). Table 64: MGCP Status Parameters Name Access Description Dynamic mgcpStatusProtocolVersion R-O Version of the MGCP protocol. Default Value: N/A N/A mgcpStatusStackVersion R-O Version of the MGCP stack. Default Value: N/A N/A mgcpStatusCallAgentAddress R-O The address of the Call Agent to which the unit is currently registered. Default Value: 0.0.0.0 N/A mgcpStatusCallAgentPortNumber R-O Port number of the Call Agent. Default Value: 0 N/A mgcpStatusRegistered R-O Unit status N/A 0 = NOT REGISTERED - The unit has not been able to successfully register with the call agent. 1 = REGISTERED - The unit is registered with the call agent whose IP address is in mgcpStatusCallAgentAddress. Default Value: 0 mgcpStatusEndpointIdGatewayFqdn VP500 Communication Unit R-O Fully Qualified Domain Name (FQDN). Default Value: N/A N/A 55 Chapter 17 - mgcpConfiguration Parameters MIB Reference Manual - MGCP MIB mgcpStatisticsThis chapter lists the various statistics information available for an Group Parameters VP500 communication unit that runs the Media Gateway Control Protocol (MGCP). Table 65: MGCP Statistics Parameters Name Access Description Dynamic mgcpStatisticsNumberOfActiveConnections R-O Number of active connections. Default Value: 0 N/A mgcpStatisticsTotalNumberOfConnections R-O Total number of connections since the last start up. Default Value: 0 N/A mgcpStatisticsAvgConnectionTime R-O Average connection time (in seconds) since the last restart. Default Value: 0 N/A mgcpStatisticsTotalNumberOfErrors R-O The total number of the errors since the last start up. Default Value: 0 N/A VP500 Communication Unit 56 Part 3: SIP MIB 18 sipUAGroup Parameters The sipUA Group parameters allow you to set information exclusive to VP500 communication units that run the Session Initiation Protocol (SIP). Introduction The SIP MIB is used with VP500 communication units that run the Session Initiation Protocol (SIP). Table 66: SIP MIB Version Parameter Name Access sipMibVersion R-O Description MIB version. Default Value: 1.0 Dynamic N/A X To use the SIP MIB In the general Provisioning MIB, locate the signalingProtocolsSwitch variable under the signalingProtocolsGroup. This variable allows you to switch from one protocol to another. Set the signalingProtocolsSwitch variable to 1=SIP. Reboot the VP500 communication unit. After the VP500 communication unit restarts, it will use the SIP MIB. sipUA Basic Parameters The following parameters allow you to define basic SIP User Agents information. Table 67: sipUA Group Parameters Name Access Description Dynamic sipUAPort R/W SIP User Agent IP port number. Default Value: 5060 Yes sipUAProtocoleVersion R-O SIP stack protocol version. Default Value: 2.0 N/A sipUAServiceOperStatus R-O Not implemented ... for future use only. N/A sipUAServiceAdminStatus R-O Not implemented ... for future use only. N/A sipUAServiceStartTime R-O Not implemented ... for future use only. N/A VP500 Communication Unit 59 Chapter 18 - sipUAGroup Parameters sipUALogGroup MIB Reference Manual - SIP MIB The following parameters allow you to set parameters pertaining to the SIP logging client. Table 68: sipUA Log Group Parameters Name Acccess sipUALogEnable R/W Description Dynamic Enable the SIP logging client (allow the stack to log SIP packets). Yes 0 = Disable 1 = Enable Default Value: 0 sipUALogUseDhcp R/W Select the provenance of the SIP logging client configuration. Yesa 0 = Static 1 = DHCP Default Value: 1 a. Only when at least one of the variables xxUseDhcp was set to 1 before starting the VP500 unit. sipUALogStaticGroup The following parameters allow you to set static information pertaining to the SIP logging client. Table 69: sipUA Log Static Group Parameters Name Acccess Description Dynamic sipUALogStaticHost R/W Static SIP logging client IP address or domain name. Default Value: 192.168.0.10 Yes sipUALogStaticPort R/W Static SIP logging client IP port number. Default Value: 6000 Yes sipUALogDhcpGroup The following parameters allow you to set DHCP information for the SIP logging client. Table 70: sipUA Log Group DHCP Parameters Name Acccess Description Dynamic sipUALogDhcpVendorSpecificCode R/W DHCP SIP logging client vendor specific code. Default Value: 202 Yes sipUALogDhcpHost R-O Logging client IP address or domain name provided by the DHCP server. Default Value: 192.168.0.10 N/A sipUALogDhcpPort R-O Logging client IP port number provided by the DHCP server. Default Value: 6000 N/A VP500 Communication Unit 60 Chapter 18 - sipUAGroup Parameters MIB Reference Manual - SIP MIB sipUAServerGroup The following parameters allow you to set basic information pertaining to the SIP server configuration. Table 71: sipUA Server Group Parameters Name Acccess sipUAServerOutboundProxyEnable R/W Description Not implemented ... for future use only. Dynamic N/A 0 = Disable 1 = Enable Default Value: 0 sipUAServerUseDhcp R/W Select the provenance of the SIP server configuration. Yesa 0 = Static 1 = DHCP Default Value: 1 a. Only when at least one of the variables xxUseDhcp was set to 1 before starting the VP500 unit. sipUAServerStaticGroup The following parameters allow you to set static information pertaining to the SIP servers. Table 72: sipUA Server Static Group Parameters Name Acccess Description Dynamic sipUAServerStaticRegistrarHost R/W Static SIP registrar server IP address or domain name. Default Value: 192.168.0.10 Yes sipUAServerStaticRegistrarPort R/W Static SIP registrar server IP port number. Default Value: 5060 Yes sipUAServerStaticProxyHost R/W Static SIP proxy server IP address or domain name. Default Value: 192.168.0.10 Yes sipUAServerStaticProxyPort R/W Static SIP proxy server IP port number. Default Value: 5060 Yes sipUAServerStaticOutboundProxyHost R/W Not implemented ... for future use only. --------------------------------------Static SIP outbound proxy server IP address or domain name. Default Value: 192.168.0.10 N/A sipUAServerStaticOutboundProxyPort R/W Not implemented ... for future use only. --------------------------------------Static SIP outbound proxy server IP port number. Default Value: 5060 N/A sipUAServerDhcpGroup The following parameters allow you to set DHCP information for the SIP servers. Table 73: sipUA Log Group Parameters Name sipUAServerDhcpRegistrarVendorSpecificCo de VP500 Communication Unit Acccess R/W Description DHCP SIP registrar server vendor specific code. Default Value: 203 Dynamic Yes 61 Chapter 18 - sipUAGroup Parameters MIB Reference Manual - SIP MIB Table 73: sipUA Log Group Parameters (Continued) Name Acccess Description Dynamic sipUAServerDhcpRegistrarHost R-O SIP registrar server IP address or domain name provided by the DHCP server. Default Value: 192.168.0.10 sipUAServerDhcpRegistrarPort R-O SIP registrar server IP port number provided by the DHCP server. N/A Default Value: 5060 sipUAServerDhcpProxyVendorSpecificCode R/W DHCP SIP proxy server vendor specific code. Default Value: 204 Yes sipUAServerDhcpProxyHost R-O SIP proxy server IP address or domain name provided by the DHCP server. Default Value: 192.168.0.10 N/A sipUAServerDhcpProxyPort R-O SIP proxy server IP port number provided by the DHCP server. Default Value: 5060 N/A sipUAServerDhcpOutboundProxyVendorSpec ificCode R/W Not implemented ... for future use only. --------------------------------------DHCP SIP outbound proxy server vendor specific code. Default Value: 205 Yes sipUAServerDhcpOutboundProxyHost R-O SIP outbound proxy server IP address or domain name provided by DHCP server. Default Value: 192.168.0.10 N/A sipUAServerDhcpOutboundProxyPort R-O SIP outbound proxy server IP port number provided by DHCP server. Default Value: 5060 N/A N/A sipUAnGroup Note: The SIP MIB may have four (4) User Agents. The parameter description is identical for each agent. For clarity’s sake, only one generic set of parameters is described in this manual. When browsing through the Provisioning MIB, replace the “n” letter in the following parameters with the proper rule number (from 1 to 4). The following parameters allow you to set parameters for the SIP User Agent #n. Table 74: sipUAn Group Parameters Name sipUAnPrefixCCAndAC Acccess R/W Description Select if the Country Code and Area Code must be prefixed to the main alias for SIP User Agent #n. Dynamic Yes 0 = Do not prefix Country Code and Area Code 1 = Prefix Country Code and Area Code Default Value: 1 sipUAnMainAlias VP500 Communication Unit R/W Main alias for SIP User Agent #n. An alias is either a user name or a telephone number. Default Value: 3331111 Yes 62 Chapter 18 - sipUAGroup Parameters MIB Reference Manual - SIP MIB Table 74: sipUAn Group Parameters (Continued) Name Acccess Description Dynamic sipUAnFriendlyName R/W Friendly name for SIP User Agent #n. Default Value: Port 1 Yes sipUAnOtherAliases R/W Semi-colon separated list of other aliases for SIP User Agent #n. An alias is either a user name or a telephone number. Default Value: Yes sipUAnMustUseSessionTimers R/W Select if the session timer must be used. Yes 0 = Don't use session timer. 1 = Must use session timer. Default Value: 0 sipUAnMaximumSessionExpirationDelay R/W Set the maximun session expiration delay in seconds. If sipUAnMustUseSessionTimers is set to 1, then an INVITE is sent every n seconds, where n is specified in the sipUAnMaximumSessionExpirationDelay variable. If an INVITE does not get an answer, then the call is terminated. This option allows to detect the end of a call caused by a communication problem on the network. If sipUAnMustUseSessionTimers is set to 0 and the network is cut off between the two telephones, then it will not be possible to detect the end of the call, because no end of communication packet will be received. Default Value: 60 Yes sipUAnAuthGroup Table 75: sipUAn AuthGroup Parameters Name Acccess Description Dynamic sipUAnAuthUsrPwd R/W Username and password used for authentication. This value is used only by this port. Default Value: Yes sipUAnAuthValid R-O This value is set to: N/A 1 = Value sipUAxAuthUsrPwd is valid. 0 = Value sipUAxAuthUsrPwd has a syntax error. Default Value: sipUAAuthGroup The following parameters allow you to set parameters for the all of the SIP User Agents Table 76: sipUA AuthGroup Parameters Name sipUAAuthUsrPwd VP500 Communication Unit Acccess R/W Description Username and password used for authentication. This value is used by all ports. Default Value: Dynamic Yes 63 Chapter 18 - sipUAGroup Parameters MIB Reference Manual - SIP MIB Table 76: sipUA AuthGroup Parameters (Continued) Name sipUAAuthValid VP500 Communication Unit Acccess R-O Description This value is set to: 1 = Value sipUAAuthUsrPwd is valid. 0 = Value sipUAAuthUsrPwd has a syntax error. Default Value: 1 Dynamic N/A 64 A List of MIB Parameters A analogGatewayID .......................................................................................................... 4 apaByPassModeAlwaysEnable ................................................................................... 33 apaByPassModeLanFailEnable ................................................................................... 33 apaByPassModeServerFailEnable .............................................................................. 33 apaCmdCheckRam ..................................................................................................... 38 apaCmdCheckRom ..................................................................................................... 37 apaCmdConfigurationMode ......................................................................................... 37 apaCmdDownloadSoftware ......................................................................................... 38 apaCmdMode .............................................................................................................. 37 apaCmdRequestConfiguration..................................................................................... 38 apaCmdRestart ........................................................................................................... 38 apaInfoFileConfigFileName ......................................................................................... 42 apaInfoFileConfigFileStatus ......................................................................................... 42 apaInfoFileConfigFileVersion ....................................................................................... 42 apaInfoInterfaceDefaultRouterIpAddress ..................................................................... 41 apaInfoInterfaceIpAddress ........................................................................................... 41 apaInfoInterfacePrimDnsIpAddress ............................................................................. 41 apaInfoInterfaceSecDnsIpAddress .............................................................................. 41 apaInfoInterfaceSubnetMask ....................................................................................... 41 apaInfoTftpFileName ................................................................................................... 41 apaInfoTftpIpAddress .................................................................................................. 41 apaInfoTftpPort ............................................................................................................ 41 apaInfoTftpWhoProvide ............................................................................................... 41 apaManagerDhcpPrimHost ......................................................................................... 12 apaManagerDhcpPrimTrapPort ................................................................................... 12 apaManagerDhcpVendorSpecificCode ........................................................................ 12 apaManagerEnable ..................................................................................................... 11 apaManagerStaticPrimHost ......................................................................................... 11 apaManagerStaticPrimTrapPort .................................................................................. 11 apaManagerTrapRetransmissionPeriod ...................................................................... 11 apaManagerTrapRetransmissionRetryCount............................................................... 11 apaManagerUseDhcp .................................................................................................. 11 apaSystemHardwareVersion ....................................................................................... 35 apaSystemLastRamCheck .......................................................................................... 35 apaSystemLastRomCheck .......................................................................................... 35 apaSystemOperationalStatusConfigFile ...................................................................... 35 apaSystemSoftwareVersion ........................................................................................ 35 apaUIMapRulexDialMap .............................................................................................. 13 apaUIMapRulexEnable ................................................................................................ 13 apaUIMapRulexIsValid ................................................................................................ 13 apaUIMapRulexPrefixDigit ........................................................................................... 14 apaUIMapRulexPrefixEnable ....................................................................................... 13 apaUIMapRulexRemDigitCount ................................................................................... 13 apaUIMapRulexRemDigitEnable ................................................................................. 13 apaUIServicesPortnCallForwardBusyAddress ............................................................. 15 apaUIServicesPortnCallForwardBusyEnable............................................................... 15 apaUIServicesPortnCallForwardNoAnswerAddress .................................................... 15 apaUIServicesPortnCallForwardNoAnswerEnable ...................................................... 15 apaUIServicesPortnCallForwardNoAnswerNumberOfRings ........................................ 15 apaUIServicesPortnCallForwardUnconditionalAddress ............................................... 14 VP500 Communication Unit 65 List of Parameters MIB Reference Manual apaUIServicesPortnCallForwardUnconditionalDisableStarNumber ............................. 15 apaUIServicesPortnCallForwardUnconditionalEnable ................................................. 14 apaUIServicesPortnCallForwardUnconditionalEnableStarNumber .............................. 14 C configTrapApaConfigInformation ................................................................................. 43 configTrapApaStatusConfigFile ................................................................................... 43 configTrapApaStatusInformation ................................................................................. 43 countryAreaCode ......................................................................................................... 21 countryCountryCode .................................................................................................... 21 countryForceConfiguration .......................................................................................... 21 countrySelection .......................................................................................................... 21 G gatewayGeneralDialPrefix ........................................................................................... 17 gatewayPermLocalDiffACAllowAll ............................................................................... 19 gatewayPermLocalDiffACAllowed ............................................................................... 18 gatewayPermLocalDiffACPrefix ................................................................................... 18 gatewayPermLocalSameACAllowAll ........................................................................... 18 gatewayPermLocalSameACAllowed ........................................................................... 18 gatewayPermLocalSameACPrefix ............................................................................... 18 gatewayPermLongDistDiffACAllowAll .......................................................................... 20 gatewayPermLongDistDiffACAllowed .......................................................................... 20 gatewayPermLongDistDiffACPrefix ............................................................................. 19 gatewayPermLongDistDiffCCAllowAll .......................................................................... 20 gatewayPermLongDistDiffCCAllowed .......................................................................... 20 gatewayPermLongDistDiffCCPrefix ............................................................................. 20 gatewayPermLongDistSameACAllowAll ...................................................................... 19 gatewayPermLongDistSameACAllowed ...................................................................... 19 gatewayPermLongDistSameACPrefix ......................................................................... 19 gatewayPortnPermissionMode .................................................................................... 17 gatewayPortnRedirectEnable ...................................................................................... 18 gatewayPortnRedirectToAddress ................................................................................ 18 I interfaceDhcpDefaultRouterIp........................................................................................ 8 interfaceDhcpLocalIp ..................................................................................................... 8 interfaceDhcpPrimDnsIp ................................................................................................ 8 interfaceDhcpSecDnsIp ................................................................................................. 8 interfaceDhcpServerIp ................................................................................................... 7 interfaceDhcpSubnetMaskIp .......................................................................................... 8 interfaceMacAddress ..................................................................................................... 7 interfaceQoSMediaDSFieldValue .................................................................................. 7 interfaceQoSMediaIeee8021QFilterEnable ................................................................... 8 interfaceQoSMediaIeee8021QUserPriority .................................................................... 9 interfaceQoSSignalingDSFiledValue ............................................................................. 7 interfaceQoSSignalingIeee8021QFilterEnable .............................................................. 8 interfaceQoSSignalingIeee8021QUserPriority ............................................................... 8 interfaceStaticDefaultRouterIp ....................................................................................... 7 interfaceStaticLocalIp .................................................................................................... 7 interfaceStaticPrimDnsIp ............................................................................................... 7 VP500 Communication Unit 66 List of Parameters MIB Reference Manual interfaceStaticSecDnsIp ................................................................................................ 7 interfaceStaticSubnetMaskIp ......................................................................................... 7 interfaceUseDhcp .......................................................................................................... 7 M mgcpConfigurationCallAgentDhcpPrimaryAddress ..................................................... 53 mgcpConfigurationCallAgentDhcpPrimaryPortNumber ............................................... 53 mgcpConfigurationCallAgentDhcpPrimaryVendorSpecificCode .................................. 53 mgcpConfigurationCallAgentDhcpSecondaryAddress ................................................. 53 mgcpConfigurationCallAgentDhcpSecondaryPortNumber ........................................... 53 mgcpConfigurationCallAgentDhcpSecondaryVendorSpecificCode ............................. 53 mgcpConfigurationCallAgentStaticPrimaryAddress ..................................................... 52 mgcpConfigurationCallAgentStaticPrimaryPortNumber ............................................... 52 mgcpConfigurationCallAgentStaticSecondaryAddress ................................................ 52 mgcpConfigurationCallAgentStaticSecondaryPortNumber .......................................... 52 mgcpConfigurationCallAgentUseDhcp ........................................................................ 52 mgcpConfigurationDtmfPackageDefaultDigitMap ........................................................ 54 mgcpConfigurationDtmfPackageInterdigitTimerLongDuration ..................................... 54 mgcpConfigurationDtmfPackageInterdigitTimerShortDuration .................................... 54 mgcpConfigurationEpIdGatewayFqdnUseDns ............................................................ 52 mgcpConfigurationEpIdLocalNameTerm1 ................................................................... 52 mgcpConfigurationEpIdStaticGatewayFqdn ................................................................ 52 mgcpConfigurationGenericMediaPackageRbkDuration ............................................... 54 mgcpConfigurationGenericMediaPackageRtDuration.................................................. 54 mgcpConfigurationLinePackageBzDuration ................................................................ 55 mgcpConfigurationLinePackageDlDuration ................................................................. 55 mgcpConfigurationLinePackageOtDuration ................................................................. 55 mgcpConfigurationLinePackageRgDuration ................................................................ 55 mgcpConfigurationLinePackageSlDuration ................................................................. 55 mgcpConfigurationResidentialGatewayPortNumber .................................................... 51 mgcpConfigurationRetransmissionAlgorithm ............................................................... 53 mgcpConfigurationRetransmissionInitialPeriod ........................................................... 53 mgcpConfigurationRetransmissionMaxPeriod ............................................................. 53 mgcpConfigurationRetransmissionRetryCount ............................................................ 53 mgcpConfigurationRetransmissionRsipInitialDelay ..................................................... 54 mgcpConfigurationRetransmissionTimeout ................................................................. 53 mgcpMibVersion .......................................................................................................... 51 mgcpStatisticsAvgConnectionTime ............................................................................. 56 mgcpStatisticsNumberOfActiveConnections ................................................................ 56 mgcpStatisticsTotalNumberOfConnections ................................................................. 56 mgcpStatisticsTotalNumberOfErrors ........................................................................... 56 mgcpStatusCallAgentAddress ..................................................................................... 55 mgcpStatusCallAgentPortNumber ............................................................................... 55 mgcpStatusEndpointIdGatewayFqdn .......................................................................... 55 mgcpStatusProtocolVersion ........................................................................................ 55 mgcpStatusRegistered ................................................................................................ 55 mgcpStatusStackVersion ............................................................................................. 55 P portForcedEndOfCallEnable ........................................................................................ 24 portForcedEndOfCallTimeout ...................................................................................... 24 portnAnalogLineType................................................................................................... 23 VP500 Communication Unit 67 List of Parameters MIB Reference Manual portnConfigurationMode .............................................................................................. 23 portnDspAdaptativityJitterBuffer .................................................................................. 24 portnDspCodecG711aLawEnable ............................................................................... 26 portnDspCodecG711aLawPTimeMax ......................................................................... 26 portnDspCodecG711aLawPTimeMin .......................................................................... 26 portnDspCodecG711uLawEnable ............................................................................... 26 portnDspCodecG711uLawPTimeMax ......................................................................... 26 portnDspCodecG711uLawPTimeMin .......................................................................... 26 portnDspCodecG7231BaudRate ................................................................................. 26 portnDspCodecG7231Enable ...................................................................................... 26 portnDspCodecG7231PTimeMax ................................................................................ 26 portnDspCodecG7231PTimeMin ................................................................................. 26 portnDspCodecG729ABEnable ................................................................................... 27 portnDspCodecG729ABPTimeMax ............................................................................. 27 portnDspCodecG729ABPTimeMin .............................................................................. 27 portnDspCodecT38Enable .......................................................................................... 27 portnDspCountrySpecificGainBaseInput ..................................................................... 25 portnDspCountrySpecificGainBaseInputOffset ............................................................ 25 portnDspCountrySpecificGainBaseOutput ................................................................... 25 portnDspCountrySpecificGainBaseOutputOffset ......................................................... 25 portnDspCountrySpecificGainConfiguration ................................................................ 25 portnDspCountrySpecificLoopCurrent ......................................................................... 25 portnDspEchoCancelControl ....................................................................................... 24 portnDspMaxJitterBufferLen ........................................................................................ 24 portnDspPreferredCodec ............................................................................................. 25 portnDspTargetJitterBufferLen..................................................................................... 24 portnDspUserGainInputOffset...................................................................................... 24 portnDspUserGainOutputOffset ................................................................................... 25 portnDspVoiceActivityDetection ................................................................................... 24 portnDtmfTransport...................................................................................................... 27 portnEnable ................................................................................................................. 23 portnType .................................................................................................................... 23 portSilenceDetectionMode ........................................................................................... 23 portSilenceDetectionTimeout ....................................................................................... 24 provisionningMibVersion ................................................................................................ 4 S sipMibVersion .............................................................................................................. 59 sipUAAuthUsrPwd ....................................................................................................... 63 sipUAAuthValid ............................................................................................................ 64 sipUALogDhcpHost ..................................................................................................... 60 sipUALogDhcpPort ...................................................................................................... 60 sipUALogDhcpVendorSpecificCode ............................................................................ 60 sipUALogEnable .......................................................................................................... 60 sipUALogStaticHost ..................................................................................................... 60 sipUALogStaticPort...................................................................................................... 60 sipUALogUseDhcp ...................................................................................................... 60 sipUAnAuthUsrPwd ..................................................................................................... 63 sipUAnAuthValid .......................................................................................................... 63 sipUAnFriendlyName ................................................................................................... 63 sipUAnMainAlias ......................................................................................................... 62 sipUAnMaximumSessionExpirationDelay .................................................................... 63 sipUAnMustUseSessionTimers ................................................................................... 63 VP500 Communication Unit 68 List of Parameters MIB Reference Manual sipUAnOtherAliases..................................................................................................... 63 sipUAnPrefixCCAndAC ............................................................................................... 62 sipUAPort .................................................................................................................... 59 sipUAProtocoleVersion ................................................................................................ 59 sipUAServerDhcpOutboundProxyHost ........................................................................ 62 sipUAServerDhcpOutboundProxyPort ......................................................................... 62 sipUAServerDhcpOutboundProxyVendorSpecificCode ............................................... 62 sipUAServerDhcpProxyHost ........................................................................................ 62 sipUAServerDhcpProxyPort ........................................................................................ 62 sipUAServerDhcpProxyVendorSpecificCode............................................................... 62 sipUAServerDhcpRegistrarHost .................................................................................. 62 sipUAServerDhcpRegistrarPort ................................................................................... 62 sipUAServerDhcpRegistrarVendorSpecificCode ......................................................... 61 sipUAServerOutboundProxyEnable ............................................................................. 61 sipUAServerStaticOutboundProxyHost ....................................................................... 61 sipUAServerStaticOutboundProxyPort ........................................................................ 61 sipUAServerStaticProxyHost ....................................................................................... 61 sipUAServerStaticProxyPort ........................................................................................ 61 sipUAServerStaticRegistrarHost .................................................................................. 61 sipUAServerStaticRegistrarPort................................................................................... 61 sipUAServerUseDhcp .................................................................................................. 61 sipUAServiceAdminStatus ........................................................................................... 59 sipUAServiceOperStatus ............................................................................................. 59 sipUAServiceStartTime ................................................................................................ 59 snmpAgentPort ............................................................................................................ 39 snmpSystemContact.................................................................................................... 39 snmpSystemDescription .............................................................................................. 39 snmpSystemLocation .................................................................................................. 39 snmpSystemName ...................................................................................................... 39 snmpSystemObjectID .................................................................................................. 39 snmpSystemService .................................................................................................... 39 sntpDhcpHost .............................................................................................................. 46 sntpDhcpPort ............................................................................................................... 46 sntpDhcpVendorCodeSpecific ..................................................................................... 46 sntpEnable................................................................................................................... 45 sntpStaticHost ............................................................................................................. 45 sntpStaticPort .............................................................................................................. 45 sntpSynchronizationPeriod .......................................................................................... 45 sntpSynchronizationPeriodOnError ............................................................................. 45 sntpTimeZoneCustomTimeZoneConfiguration ............................................................ 46 sntpTimeZoneCustomTimeZoneIsValid ....................................................................... 47 sntpTimeZoneTimeZoneSelection ............................................................................... 46 sntpTimeZoneUseTimeZoneSelection ......................................................................... 46 sntpUseDhcp ............................................................................................................... 45 syslogDhcpHost ........................................................................................................... 30 syslogDhcpPort ........................................................................................................... 30 syslogDhcpVendorSpecificCode.................................................................................. 30 syslogMsgEnable......................................................................................................... 29 syslogStaticHost .......................................................................................................... 29 syslogStaticPort ........................................................................................................... 29 syslogTracingMask ...................................................................................................... 29 syslogUseDhcp ............................................................................................................ 29 VP500 Communication Unit 69 List of Parameters MIB Reference Manual T tftpBlockSize ................................................................................................................ 31 tftpDownloadStatus...................................................................................................... 31 tftpEmergencyFileName .............................................................................................. 31 tftpFileName ................................................................................................................ 31 tftpServerDhcpEmergencyHost ................................................................................... 32 tftpServerDhcpEmergencyPort .................................................................................... 32 tftpServerDhcpEmergencyVendorSpecificCode .......................................................... 32 tftpServerDhcpHost ..................................................................................................... 32 tftpServerDhcpPort ...................................................................................................... 32 tftpServerDhcpVendorSpecificCode ............................................................................ 32 tftpServerStaticEmergencyHost ................................................................................... 32 tftpServerStaticEmergencyPort.................................................................................... 32 tftpServerStaticHost ..................................................................................................... 31 tftpServerStaticPort...................................................................................................... 31 tftpTimeOut .................................................................................................................. 31 tftpUseDhcp ................................................................................................................. 31 VP500 Communication Unit 70