Download Brother HL-2280DW Setup guide
Transcript
Quick Setup Guide Start Here HL-2280DW Please read the Safety and Legal booklet first before you set up your machine. Then, please read this Quick Setup Guide for the correct setup and installation. To view the Quick Setup Guide in other languages, please visit http://solutions.brother.com/. WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injuries. CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injuries. 1 Unpack the machine and check the components Installation CD-ROM, Documentation CD-ROM Product Registration Sheet (USA only) AC Power Cord Basic User’s Guide Quick Setup Guide Safety and Legal booklet Drum Unit and Toner Cartridge Assembly (pre-installed) WARNING Plastic bags are used in the packaging of your machine. Plastic bags are not toys. To avoid danger of suffocation, please keep these bags away from babies and children and dispose of them properly. USA/CAN Version A 1 CAUTION CAUTION When you move the machine, grasp the side handholds that are under the scanner. DO NOT carry the machine by holding it at the bottom. Note • Keep a minimum gap around the machine as shown in the illustration. 13.8 in. (350 mm) 3.95 in. (100 mm) 3.95 in. (100 mm) 3.55 in. (90 mm) • The components included in the box may differ depending on your country. • Please save the original packaging should you need to ship the machine in future. • If for any reason you must ship your machine, carefully repack the machine in the original packaging to avoid any damage during transit. The machine should be adequately insured with the carrier. For how to repack the machine, see Packing and shipping the machine in the Advanced User's Guide. • The interface cable is not a standard accessory. Buy the appropriate interface cable for the interface you want to use (USB or Network). USB cable • It is recommended to use a USB 2.0 cable (Type A/B) that is no longer than 6 feet (2 meters). • DO NOT connect the interface cable at this time. Connecting the interface cable is done during the MFL-Pro installation process. Network cable Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or 100BASE-TX Fast Ethernet Network. 2 2 Remove the packing material from the machine d Lift the elastic band off the drum. IMPORTANT DO NOT connect the AC power cord yet. a b Remove the packing tape from the outside of the machine and the film covering the scanner glass. Open the front cover. e c Pull the paper strip to remove the protective material as shown in the illustration. Remove the Silica Pack from the inside of the machine. f Take out the drum unit and toner cartridge assembly. CAUTION CAUTION DO NOT eat the Silica Pack. Please discard. If ingested seek medical attention immediately. 3 g Gently shake it from side to side several times to distribute the toner evenly inside the assembly. a h Pull the paper tray completely out of the machine. Put the drum unit and toner cartridge assembly back in the machine. b i 3 Load paper in the paper tray While pressing the green paper-guide release lever a, slide the paper guides to fit the paper size you are loading in the tray. Make sure that the guides are firmly in the slots. Close the front cover of the machine. 1 4 Note d For Legal or Folio size paper, press the release button in the bottom of the paper tray and then pull out the back of the paper tray. (Legal or Folio size paper are not available in some regions.) Put paper in the tray and make sure: The paper is below the maximum paper mark (b b b) a. Over filling the paper tray will cause paper jams. The side to be printed on must be face down. The paper guides touch the sides of the paper so it will feed properly. 1 c Fan the stack of paper well to avoid paper jams and misfeeds. e Put the paper tray firmly back in the machine. Make sure that it is completely inserted into the machine. For more information about recommended paper, see Recommended paper and print media in the Basic User’s Guide. 5 4 IMPORTANT DO NOT connect the interface cable yet. a b 6 Connect the power cord Connect the AC power cord to the machine, and then plug it into an AC power outlet. Turn on the machine’s power switch. Set the LCD contrast (if needed) If you are having difficulty reading the LCD, try changing the contrast setting. a b c d Press Menu. Press a or b to choose 1.General Setup. Press OK. Press a or b to choose 3.LCD Contrast. Press OK. Press a to increase the contrast. —OR— Press b to decrease the contrast. Press OK. e a b c d 5 Choose your language (if needed) Press Menu. Press a or b to choose 1.General Setup. Press OK. Press a or b to choose 0.Local Language. Press OK. Press a or b to choose your language. Press OK. e 6 Press Stop/Exit. Press Stop/Exit. 7 Choose your connection type These installation instructions are for Windows® 2000 Professional, Windows® XP Home/Windows® XP Professional, Windows® XP Professional x64 Edition, Windows Vista®, Windows® 7, and Mac OS X (versions 10.4.11, 10.5.x and 10.6.x). Note For Windows Server® 2003/2003 x64 Edition/2008/2008 R2, visit your model page at http://solutions.brother.com/. Windows® Macintosh 7 Macintosh Note You can download the latest drivers and utilities for your machine from the Brother Solutions Center at http://solutions.brother.com/. Windows® Windows® and Macintosh go to page 16 Wireless Network For Wireless Network Macintosh Windows®, go to page 12 Macintosh, go to page 14 Wired Network For Wired Network USB Windows®, go to page 8 Macintosh, go to page 10 Windows® For USB Interface Users USB Windows® For USB Interface Users (Windows® 2000 Professional/XP/XP Professional x64 Edition/Windows Vista®/Windows® 7) a 8 Before you install Make sure that your computer is ON and you are logged on with Administrator rights. a IMPORTANT • If there are any programs running, close them. • The screens may differ depending on your operating system. Note The installation CD-ROM includes ScanSoft™ PaperPort™ 12SE. This software supports Windows® XP (SP3 or greater), XP Professional x64 Edition (SP2 or greater), Windows Vista® (SP2 or greater) and Windows® 7. Update to the latest Windows® Service Pack before installing MFL-Pro Suite. For Windows® 2000 (SP4 or greater) users, when the ScanSoft™ PaperPort™ 11SE download screen appears during the installation of MFL-Pro Suite, follow the on-screen instructions. b Turn off the machine and make sure the USB interface cable is NOT connected to the machine. If you have already connected the cable, disconnect it. 9 Install MFL-Pro Suite Put the installation CD-ROM into your CD-ROM drive. If the model name screen appears, choose your machine. If the language screen appears, choose your language. Note If the Brother screen does not appear automatically, go to My Computer (Computer), double-click the CD-ROM icon, and then double-click start.exe. b c Click Initial Installation and then Install MFL-Pro Suite. Click Yes if you accept the license agreements. Note • If the installation does not continue automatically, open the top menu again by ejecting and then reinserting the CD-ROM or double-click the start.exe program from the root folder, and continue from step b to install MFL-Pro Suite. • For Windows Vista® and Windows® 7 users, when the User Account Control screen appears, click Allow or Yes. d 8 Follow the on-screen instructions until this screen appears. USB e Windows® Connect the USB cable to the USB connector marked with the symbol on your machine and then connect the cable to your computer. f Turn the machine on, and follow the on-screen instructions to complete setup. • If an error message appears during the software installation, run the Installation Diagnostics located in Start/All Programs/Brother/HL-2280DW. Finish The installation is now complete. Note • Depending on your security settings, a Windows Security or antivirus software window may appear when using the machine or its software. Please allow or permit the window to continue. • XML Paper Specification Printer Driver The XML Paper Specification Printer Driver is the most suitable driver for Windows Vista® and Windows® 7 when printing from applications that use the XML Paper Specification documents. Please download the latest driver by accessing the Brother Solutions Center at http://solutions.brother.com/. 9 Macintosh USB Note • For Windows Vista® and Windows® 7 users, when the Windows Security screen appears, click the check box and click Install to complete the installation correctly. Windows® IMPORTANT DO NOT cancel any of the screens during the installation. It may take a few seconds for all screens to appear. USB Macintosh For USB Interface Users (Mac OS X 10.4.11 - 10.6.x) a 8 Before you install Make sure your machine is connected to the power and your Macintosh is ON. You must be logged on with Administrator rights. IMPORTANT a b 9 Install MFL-Pro Suite Put the installation CD-ROM into your CD-ROM drive. Double-click the Start Here OSX icon. Follow the on-screen instructions. For Mac OS X 10.4.10 users, upgrade to Mac OS X 10.4.11 - 10.6.x. (For the latest drivers and information on the Mac OS X you are using, visit http://solutions.brother.com/.) b Connect the USB cable to the USB connector marked with the symbol on your machine and then connect the cable to your Macintosh. Note It may take a few minutes for installation to complete. c c Follow the on-screen instructions until this screen appears. Choose your machine from the list, and then click OK. Make sure your machine’s power switch is on. d When this screen appears, click Next. The installation of MFL-Pro Suite is now complete. Go to step 10 on page 11. 10 USB 10 Macintosh Download and install Presto! PageManager When Presto! PageManager is installed OCR capability is added to Brother ControlCenter2. You can easily scan, share and organize photos and documents using Presto! PageManager. On the Brother Support screen, click Presto! PageManager and follow the on-screen instructions. Macintosh 11 Windows® The installation is now complete. USB Finish Wired Network Windows® For Wired Network Interface Users (Windows® 2000 Professional/XP/XP Professional x64 Edition/Windows Vista®/Windows® 7) a 8 Before you install c Connect the network interface cable to the LAN connector and then connect it to a free port on your hub. Make sure that your computer is ON and you are logged on with Administrator rights. IMPORTANT • If there are any programs running, close them. • The screens may differ depending on your operating system. d Note • The installation CD-ROM includes ScanSoft™ PaperPort™ 12SE. This software supports Windows® XP (SP3 or greater), XP Professional x64 Edition (SP2 or greater), Windows Vista® (SP2 or greater) and Windows® 7. Update to the latest Windows® Service Pack before installing MFL-Pro Suite. For Windows® 2000 (SP4 or greater) users, when the ScanSoft™ PaperPort™ 11SE download screen appears during the installation of MFL-Pro Suite, follow the on-screen instructions. • Disable all personal firewall software (other than Windows® Firewall), anti-spyware or antivirus applications for the duration of the installation. b a Make sure your machine’s power switch is on. 9 Install MFL-Pro Suite Put the installation CD-ROM into your CD-ROM drive. If the model name screen appears, choose your machine. If the language screen appears, choose your language. Note If the Brother screen does not appear automatically, go to My Computer (Computer), double-click the CD-ROM icon, and then double-click start.exe. b Click Initial Installation and then Install MFL-Pro Suite. Remove the protective cap from the LAN connector marked with a symbol. c Click Yes if you accept the license agreements. Note • If the installation does not continue automatically, open the top menu again by ejecting and then reinserting the CD-ROM or double-click the start.exe program from the root folder, and continue from step b to install MFL-Pro Suite. • For Windows Vista® and Windows® 7 users, when the User Account Control screen appears, click Allow or Yes. 12 Wired Network d When the Firewall/AntiVirus detected screen appears, choose Change the Firewall port settings to enable network connection and continue with the installation. (Recommended) and click Next. (Not for Windows® 2000 users) Windows® 10 Install MFL-Pro Suite on additional computers (if needed) If you want to use your machine with multiple computers on the network, install MFL-Pro Suite on each computer. Go to step 9 on page 12. Note If you are not using the Windows® Firewall, see the user's guide of your firewall or antivirus software for information on how to add the following network ports. For network scanning, add UDP port 54925. If you still have trouble with your network connection, add UDP port 137. e Follow the on-screen instructions to complete setup. IMPORTANT DO NOT cancel any of the screens during the installation. It may take a few seconds for all screens to appear. • For Windows Vista® and Windows® 7 users, when the Windows Security screen appears, click the check box and click Install to complete the installation correctly. • If an error message appears during the software installation, run the Installation Diagnostics located in Start/All Programs/Brother/HL-2280DW LAN. Note • If you use a specified IP Address for the machine, you must set the Boot Method to Static by using the control panel. For more information, see Network menu in the Network User's Guide. • Depending on your security settings, a Windows Security or antivirus software window may appear when using the machine or its software. Please allow or permit the window to continue. • XML Paper Specification Printer Driver The XML Paper Specification Printer Driver is the most suitable driver for Windows Vista® and Windows® 7 when printing from applications that use the XML Paper Specification documents. Please download the latest driver by accessing the Brother Solutions Center at http://solutions.brother.com/. 13 Macintosh • You can find your machine’s IP address and the node name by printing out the Network Configuration Report. See Print the Network Configuration Report on page 32. The installation is now complete. Wired Network • If your machine is not found over the network, confirm your settings by following the on-screen instructions. Finish Windows® Note Network license (Windows®) This product includes a PC license for up to 5 users. This license supports the installation of the MFL-Pro Suite including ScanSoft™ PaperPort™ 12SE or ScanSoft™ PaperPort™ 11SE on up to 5 PCs on the network. If you want to use more than 5 PCs with ScanSoft™ PaperPort™ 12SE or ScanSoft™ PaperPort™ 11SE installed, please purchase the Brother NL-5 pack which is a multiple PC license agreement pack for up to 5 additional users. To purchase the NL-5 pack, contact your authorized Brother dealer or contact Brother customer service. Wired Network Macintosh For Wired Network Interface Users (Mac OS X 10.4.11 - 10.6.x) a 8 Before you install Make sure your machine is connected to the power and your Macintosh is ON. You must be logged on with Administrator rights. IMPORTANT a b 9 Install MFL-Pro Suite Put the installation CD-ROM into your CD-ROM drive. Double-click the Start Here OSX icon. Follow the on-screen instructions. For Mac OS X 10.4.10 users, upgrade to Mac OS X 10.4.11 - 10.6.x. (For the latest drivers and information on the Mac OS X you are using, visit http://solutions.brother.com/.) b Remove the protective cap from the LAN connector marked with a symbol. Note It may take a few minutes for installation to complete. c c Follow the on-screen instructions until this screen appears. Choose your machine from the list, and then click OK. Connect the network interface cable to the LAN connector and then connect it to a free port on your hub. Note If your machine is not found over the network, confirm your network settings. d 14 Make sure your machine’s power switch is on. Wired Network Note • You can find your machine’s MAC Address (Ethernet Address) and IP Address by printing out the Network Configuration Report. See Print the Network Configuration Report on page 32. • If this screen appears click OK. Enter a name for your Macintosh in Display Name up to 15 characters long and click OK. Go to d. • If you want to use the machine’s SCAN key to scan over the network, you must check the Register your computer with the "Scan To" function on the machine box. When Presto! PageManager is installed OCR capability is added to Brother ControlCenter2. You can easily scan, share and organize photos and documents using Presto! PageManager. On the Brother Support screen, click Presto! PageManager and follow the on-screen instructions. 11 Install MFL-Pro Suite on additional computers (if needed) If you want to use your machine with multiple computers on the network, install MFL-Pro Suite on each computer. Go to step 9 on page 14. Finish The installation is now complete. When this screen appears, click Next. Note 15 Macintosh The installation of MFL-Pro Suite is now complete. Go to step 10 on page 15. If you use a specified IP Address for the machine, you must set the Boot Method to Static by using the control panel. For more information, see Network menu in the Network User's Guide. Wired Network d 10 Download and install Presto! PageManager Windows® • The name you enter will appear on the machine’s LCD when you press (SCAN) and choose a scan option. (For more information, see Network Scanning in the Software User's Guide.) Macintosh For Wireless Network Users For Wireless Network Interface Users 8 Before you begin First you must configure the wireless network settings of your machine to communicate with your network access point/router. After the machine is configured to communicate with your access point/router, computers on your network will have access to the machine. To use the machine from these computers, you will need to install the drivers and software. The following steps will guide you through the configuration and installation process. IMPORTANT • If you are going to connect the machine to your network, we recommend that you contact your system administrator prior to installation. You must know your wireless network settings before you proceed with this installation. • If you have previously configured the wireless settings of the machine you must reset the network (LAN) settings before you can configure the wireless settings again. 1. On your machine, press Menu and a or b to choose 4.Network. Press OK. 2. a or b to choose 0.Network Reset. Press OK. 3. Press a to choose Reset. 4. Press a to choose Yes. Note • To achieve optimum results with normal everyday document printing, place the Brother machine as close to the network access point/router as possible with minimal obstructions. Large objects and walls between the two devices as well as interference from other electronic devices can affect the data transfer speed of your documents. Due to these factors, wireless may not be the best method of connection for all types of documents and applications. If you are printing large files, such as multi-page documents with mixed text and large graphics, you may want to consider choosing wired Ethernet for a faster data transfer or USB for the fastest throughput speed. • Although the Brother HL-2280DW can be used in both a wired and wireless network, only one of the connection methods can be used at a time. Infrastructure Mode a Access point/router 1 b Wireless Network machine (your machine) 4 2 c Wireless capable computer connected to the access point/router d Wired computer connected to the access point/router 3 16 For Wireless Network Users 9 Choose your wireless install method The following instructions will offer three methods for installing your Brother machine in a wireless network environment. Choose the method you prefer for your environment. Note To setup your machine in any other wireless environment, you can find instructions in the Network User's Guide. a Configuration using the Installation CD-ROM and temporarily using a USB cable (Windows® only). It is recommended that you use a PC wirelessly connected to your network for this method. IMPORTANT • You need to temporarily use a USB cable during configuration (cable not included). • For Windows® 2000 and Windows® XP users you will need to know the wireless settings of your network before you proceed. Please write down your wireless network settings in the area below. Item Record the current wireless network settings SSID (Network Name) Network Key (Security Key/Encryption Key) * The Network Key may also be described as the Password, Security Key or Encryption Key. IMPORTANT Please do not contact Brother Customer Service for assistance without the wireless security information. We cannot assist you in locating your network security settings. Note • If you do not know this information (SSID and Network Key), you cannot continue the wireless setup. 2. The initial network name could be the manufacturer’s name or the model name. 3. If you do not know the security information, please consult the router manufacturer, your system administrator, or internet provider. page 19 17 Macintosh Now go to Wireless Network 1. You should see the documentation provided with your wireless access point/router. Windows® • How can I find this information (SSID and Network Key)? For Wireless Network Users b Manual configuration from the control panel (Windows® and Macintosh) If your wireless access point/router does not support Wi-Fi Protected Setup (WPS) or AOSS™, write down the wireless network settings of your wireless access point/router in the area below. IMPORTANT Please do not contact Brother Customer Service for assistance without the wireless security information. We cannot assist you in locating your network security settings. Item Record the current wireless network settings SSID (Network Name) Network Key (Security Key/Encryption Key) * The Network Key may also be described as the Password, Security Key or Encryption Key. Note • If you do not know this information (SSID and Network Key), you cannot continue the wireless setup. • How can I find this information (SSID and Network Key)? 1. You should see the documentation provided with your wireless access point/router. 2. The initial network name could be the manufacturer’s name or the model name. 3. If you do not know the security information, please consult the router manufacturer, your system administrator, or internet provider. Now go to c One push configuration using Wi-Fi Protected Setup or AOSS™ (Windows® and Macintosh) If your wireless access point/router supports automatic wireless (one-push) setup (Wi-Fi Protected Setup or AOSS™) Now go to 18 page 22 page 23 For Wireless Network Users Configuration using the Installation CD-ROM and temporarily using a USB cable (Windows® only) 10 Configure the wireless settings e When this screen appears, choose Change the Firewall port settings to enable network connection and continue with the installation. (Recommended) and click Next. (Not for Windows® 2000 users) IMPORTANT • You need to temporarily use a USB cable or Ethernet cable during configuration (cable not included). • For Windows® 2000 and Windows® XP users you must have the wireless settings you wrote down for your network in step 9 on page 17 before you proceed. a If you are not using the Windows® Firewall, see the user's guide of your firewall or antivirus software for information on how to add the following network ports. For network scanning, add UDP port 54925. If you still have trouble with your network connection, add UDP port 137. Put the installation CD-ROM into your CD-ROM drive. If prompted, select your model and language. Note If the Brother screen does not appear automatically, go to My Computer (Computer), double-click the CD-ROM icon, and then double-click start.exe. b f Choose No and then click Next. Click Initial Installation and then Install MFL-Pro Suite. g c d Click Yes if you accept the license agreement. Follow the on-screen instructions. Read the Important Notice. Check the box after you confirm the SSID and Network Key, and then click Next. Choose Wireless Network Connection and then click Next. 19 Macintosh Note For Windows Vista® and Windows® 7, when the User Account Control screen appears, click Allow or Yes. Windows® If you are installing from a wireless PC running Windows Vista® or Windows® 7, check the box and then click next. The installer will automatically detect your wireless network settings. Wireless Network Note For Wireless Network Users h i j Choose Temporarily use a USB cable (Recommended) and then click Next. Note • If the list is blank, check that the access point has power and is broadcasting the SSID, and then see if the machine and the access point are within range for wireless communication. Then, click Refresh. • If your access point is set to not broadcast the SSID you can manually add it by clicking the Advanced button. Follow the on-screen instructions for entering the Name (SSID), and then click Next. Temporarily connect the USB cable (not included) directly to the computer and the machine. If the confirmation screen appears, check the box and click Next. When the following screen appears, check Yes if you want to connect with the listed SSID. Click Next and go to n. l m k 20 The wizard will search for wireless networks available from your machine. Choose the SSID that you wrote down for your network in step 9 on page 17, and then click Next. If your network is not configured for Authentication and Encryption, the following screen will appear. To continue configuration, click OK and go to n. Enter the Network Key you wrote down in step 9 on page 17 and then enter the key again in Confirm Network Key, then click Next. For Wireless Network Users n Click Next. The settings will be sent to your machine. Note • The settings will remain unchanged if you click Cancel. • If you want to manually enter the IP address settings of your machine, click Change IP Address and enter the necessary IP address settings for your network. • If the wireless setup failure screen appears, click Retry and try starting from step k again. o p A connection result message appears for 60 seconds on the LCD. Disconnect the USB cable between the computer and the machine. Wireless setup is now complete. To install MFL-Pro Suite, continue to step f on page 29. Macintosh Wireless Network 21 Windows® Now go to page 29 For Wireless Network Users Manual configuration from the control panel (Windows® and Macintosh) 10 Configure the wireless settings IMPORTANT You must have the wireless settings you wrote down for your network in step 9 on page 17 before you proceed. a b On your machine, press Menu and press a or b to choose 4.Network, and press OK. Press a or b to choose 2.WLAN, and press OK. Press a or b to choose 2.Setup Wizard, and press OK. Enter the Network Key you wrote down in step 9 on page 17 using a or b to choose each letter or number. To delete the letters you have entered, press Clear. When WLAN Enable ? is displayed, press a to choose On. This will start the wireless setup wizard. For example, to enter the letter a, press a or b until it appears. To enter the next character, press OK. Otherwise press Stop/Exit to exit from the wireless setup wizard. For more information, see Entering Text for Wireless Settings on page 27. The machine will search for available SSIDs. If a list of SSIDs is displayed, use the a or b key to choose the SSID you wrote down in step 9 on page 17, then press OK. If you are using an authentication and encryption method that requires a Network Key, go to c. If your authentication method is Open System and your encryption mode is None, go to e. Note • It will take several seconds to display a list of available SSIDs. • If a list of SSIDs is not displayed, make sure your access point is on. Move your machine closer to the access point and try starting from a again. • If your access point is set to not broadcast the SSID you will have to manually add the SSID name. For details, see Configuring your machine when the SSID is not broadcast in the Network User's Guide. If your wireless access point/router supports Wi-Fi Protected Setup, Selected access point supports WPS. Use WPS? appears. To connect your machine using the automatic wireless mode, press a to choose Yes. (If you choose No, go to c to enter the Network Key.) When Start WPS on your wireless access point/router,then choose Next. appears, press the Wi-Fi Protected Setup button on your wireless access point/router, and then press a to choose Next. Go to e. 22 c d e Press OK twice when you have entered all the characters, then press a or b to choose Yes, and press OK to apply your settings. Go to d. Your machine will now try to connect to your wireless network using the information you have entered. A connection result message appears on the LCD and a WLAN report will automatically be printed. If the connection failed, check the error code on the printed report and refer to Troubleshooting on page 24. Wireless setup is now complete. To install the MFL-Pro Suite, continue to step 11. For Windows® Users: Now go to page 28 For Macintosh Users: Now go to page 30 For Wireless Network Users One push configuration using Wi-Fi Protected Setup or AOSS™ (Windows® and Macintosh) 10 a b c Configure the wireless settings Confirm your wireless access point/router has the Wi-Fi Protected Setup or AOSS™ symbol as shown below. Place the Brother machine within range of your Wi-Fi Protected Setup or AOSS™ access point/router. The range may differ depending on your environment. Refer to the instructions provided with your access point/router. On your machine, press Menu and press a or b to choose 4.Network, and press OK. Press a or b to choose 2.WLAN, and press OK. Press a or b to choose 3.WPS/AOSS, and press OK. When WLAN Enable ? is displayed, press a to choose On. This will start the wireless setup wizard. Otherwise press Stop/Exit to exit from the wireless setup wizard. When Start WPS/AOSS on your wireless access point/router. appears, press the Wi-Fi Protected Setup or AOSS™ button on your wireless access point/router. See the user’s guide for your wireless access point/router for instructions. And then press OK. d A connection result message appears on the LCD and a WLAN report will automatically be printed. If the connection failed, check the error code on the printed report and refer to Troubleshooting on page 24. Wireless setup is now complete. To install the MFL-Pro Suite, continue to step 11. For Windows® Users: Now go to page 28 For Macintosh Users: Now go to page 30 Macintosh 23 Windows® Wireless Network This feature will automatically detect which mode (Wi-Fi Protected Setup or AOSS™) your access point/router uses to configure your machine. Note If your wireless access point/router supports Wi-Fi Protected Setup (PIN Method) and you want to configure your machine using the PIN (Personal Identification Number) Method, see Using the PIN Method of Wi-Fi Protected Setup in the Network User's Guide. For Wireless Network Users Troubleshooting IMPORTANT Please do not contact Brother Customer Service for assistance without the wireless security information. We cannot assist you in locating your network security settings. How can I find the wireless settings (SSID and Network Key) 1. You should see the documentation provided with your wireless access point/router. 2. The initial network name could be the manufacturer’s name or the model name. 3. If you do not know the security information, please consult the router manufacturer, your system administrator or internet provider. * The Network Key may also be described as the Password, Security Key or Encryption Key. * If the wireless access point/router is set to not broadcast the SSID, the SSID will not automatically be detected. You will have to manually enter the SSID name. See Configuring your machine when the SSID is not broadcast in the Network User's Guide. WLAN report If the WLAN report that printed shows that the connection failed, check the error code on the printed report and refer to the following instructions. Error code Recommended Solutions The wireless setting is not activated, turn the wireless setting to ON. TS-01 - If a LAN cable is connected to your machine, disconnect it and turn the wireless setting of your machine to ON. 1. On your machine, press Menu and press a or b to choose 4.Network, and press OK. Press a or b to choose 2.WLAN, and press OK. Press a or b to choose 2.Setup Wizard, and press OK. 2. When WLAN Enable ? is displayed, press a to choose On. This will start the wireless setup wizard. The wireless access point/router cannot be detected. 1. Check the following 4 points. TS-02 - Make sure that the wireless access point/router is powered on. - Move your machine to an obstruction-free area, or closer to the wireless access point/router. - Temporarily place your machine within about 3.3 feet (one meter) from the wireless access point when you are configuring the wireless settings. - If your wireless access point/router is using MAC address filtering, confirm the MAC address of the Brother machine is allowed in the filter. 2. If you manually entered the SSID and security information (SSID/authentication method/encryption method/Network Key) the information may be incorrect. Reconfirm the SSID and security information and re-enter the correct information as necessary. See How can I find the wireless settings (SSID and Network Key) on page 24 to confirm. 24 For Wireless Network Users Error code Recommended Solutions The Authentication/Encryption methods used by the selected wireless access point/router are not supported by your machine. For infrastructure mode, change the authentication and encryption methods of the wireless access point/router. Your machine supports the following authentication methods WPA, WPA2, OPEN and Shared key. WPA supports TKIP or AES encryption methods. WPA2 supports AES for the encryption method. OPEN and Shared key correspond to WEP encryption. If your problem is not solved, the SSID or network settings you entered may be incorrect. Reconfirm the wireless network settings. Combined table of authentication and encryption methods TS-04 Authentication method Encryption method WPA-Personal TKIP AES WPA2-Personal AES OPEN WEP NONE (without encryption) Shared key WEP See How can I find the wireless settings (SSID and Network Key) on page 24 to confirm. For ad-hoc mode, change the authentication and encryption methods of your computer for the wireless setting. Your machine supports OPEN authentication method only, with optional WEP encryption. TS-05 The security information (SSID/Network Key) is incorrect. Reconfirm the SSID and security information (Network Key). If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother machine supports the use of the first WEP key only. See How can I find the wireless settings (SSID and Network Key) on page 24 to confirm. TS-06 The wireless security information (Authentication method/Encryption method/Network Key) is incorrect. Reconfirm the wireless security information (Authentication method/Encryption method/Network Key) in the table of TS-04. If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother machine supports the use of the first WEP key only. See How can I find the wireless settings (SSID and Network Key) on page 24 to confirm. Windows® Macintosh Wireless Network 25 For Wireless Network Users Error code Recommended Solutions The machine cannot detect a wireless access point/router that has WPS or AOSS™ enabled. If you would like to configure your wireless settings using WPS or AOSS™, you must operate both your machine and the wireless access point/router. Confirm your wireless access point/router supports WPS or AOSS™ and try starting again. TS-07 If you do not know how to operate your wireless access point/router using WPS or AOSS™, see the documentation provided with your wireless access point/router, ask the manufacturer of your wireless access point/router or ask your network administrator. Two or more wireless access points that have WPS or AOSS™ enabled are detected. TS-08 26 - Confirm that only one wireless access point/router within range has the WPS or AOSS™ method active and try again. - Try starting again after a few minutes in order to avoid interference from other access points. For Wireless Network Users Entering Text for Wireless Settings Press a or b repeatedly to select a character from the table below: For configuring wireless network settings (space) ! " # $ % & ' ( ) * + , - . / 0 1 2 3 4 5 6 7 8 9 : ; < = > ? @ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z [ \ ] ^ _ ` a b c d e f g h i j k l m n o p q r s t u v w x y z { | } ~ Making corrections If you entered a letter incorrectly and want to change it, press Clear. Re-enter the correct character. Windows® Macintosh Wireless Network 27 Wireless Network Windows® Install the Drivers & Software (Windows® 2000 Professional/XP/XP Professional x64 Edition/ Windows Vista®/Windows® 7) 11 Before you install b Click Initial Installation and then Install MFL-Pro Suite. Make sure that your computer is ON and you are logged on with Administrator rights. IMPORTANT • If there are any programs running, close them. • The screens may differ depending on your operating system. Note • The installation CD-ROM includes ScanSoft™ PaperPort™ 12SE. This software supports Windows® XP (SP3 or greater), XP Professional x64 Edition (SP2 or greater), Windows Vista® (SP2 or greater) and Windows® 7. Update to the latest Windows® Service Pack before installing MFL-Pro Suite. For Windows® 2000 (SP4 or greater) users, when the ScanSoft™ PaperPort™ 11SE download screen appears during the installation of MFL-Pro Suite, follow the on-screen instructions. • Disable all personal firewall software (other than Windows® Firewall), anti-spyware or antivirus applications for the duration of the installation. 12 a Click Yes if you accept the license agreements. Note • If the installation does not continue automatically, open the top menu again by ejecting and then reinserting the CD-ROM or double-click the start.exe program from the root folder, and continue from step b to install MFL-Pro Suite. • For Windows Vista® and Windows® 7 users, when the User Account Control screen appears, click Allow or Yes. d e Choose Wireless Network Connection and click Next. When the Firewall/AntiVirus detected screen appears, choose Change the Firewall port settings to enable network connection and continue with the installation. (Recommended) and click Next. (Not for Windows® 2000 users) Install MFL-Pro Suite Put the installation CD-ROM into your CD-ROM drive. If the model name screen appears, choose your machine. If the language screen appears, choose your language. Note If the Brother screen does not appear automatically, go to My Computer (Computer), double-click the CD-ROM icon, and then double-click start.exe. 28 c If you are not using the Windows® Firewall, see the user's guide of your firewall or antivirus software for information on how to add the following network ports. For network scanning, add UDP port 54925. If you still have trouble with your network connection, add UDP port 137. Wireless Network f Follow the on-screen instructions until this screen appears. Choose the machine from the list, and then click Next. Windows® 13 Install MFL-Pro Suite on additional computers (if needed) If you want to use your machine with multiple computers on the network, install MFL-Pro Suite on each computer. Go to step 12 on page 28. Note Note If you are using WEP and the LCD displayed ‘Connected’ but your machine is not found, make sure you entered the WEP key correctly. The WEP key is case sensitive. g Follow the on-screen instructions to complete setup. IMPORTANT DO NOT cancel any of the screens during the installation. It may take a few seconds for all screens to appear. Network license (Windows®) This product includes a PC license for up to 5 users. This license supports the installation of the MFL-Pro Suite including ScanSoft™ PaperPort™ 12SE or ScanSoft™ PaperPort™ 11SE on up to 5 PCs on the network. If you want to use more than 5 PCs with ScanSoft™ PaperPort™ 12SE or ScanSoft™ PaperPort™ 11SE installed, please purchase the Brother NL-5 pack which is a multiple PC license agreement pack for up to 5 additional users. To purchase the NL-5 pack, contact your authorized Brother dealer or contact Brother customer service. Finish The installation is now complete. Note • For Windows Vista® and Windows® 7 users, when the Windows Security screen appears, click the check box and click Install to complete the installation correctly. • If an error message appears during the software installation, run the Installation Diagnostics located in Start/All Programs/Brother/HL-2280DW LAN. Note • If you use a specified IP Address for the machine, you must set the Boot Method to Static by using the control panel. For more information, see Network menu in the Network User's Guide. • Depending on your security settings, a Windows Security or antivirus software window may appear when using the machine or its software. Please allow or permit the window to continue. Macintosh 29 Windows® Wireless Network • XML Paper Specification Printer Driver The XML Paper Specification Printer Driver is the most suitable driver for Windows Vista® and Windows® 7 when printing from applications that use the XML Paper Specification documents. Please download the latest driver by accessing the Brother Solutions Center at http://solutions.brother.com/. Wireless Network Macintosh Install the Drivers & Software (Mac OS X 10.4.11 - 10.6.x) 11 Before you install c Choose Wireless Network Connection and click Next. Make sure your machine is connected to the power and your Macintosh is ON. You must be logged on with Administrator rights. IMPORTANT For Mac OS X 10.4.10 users, upgrade to Mac OS X 10.4.11 - 10.6.x. (For the latest drivers and information on the Mac OS X you are using, visit http://solutions.brother.com/.) 12 a b 30 IMPORTANT DO NOT cancel any of the screens during the installation. Install MFL-Pro Suite Put the installation CD-ROM into your CD-ROM drive. Double-click the Start Here OSX icon. Follow the on-screen instructions. Note • It may take a few minutes for installation to complete. • If your wireless settings fail, the Wireless Device Setup Wizard screen appears. Follow the on-screen instructions to complete the wireless configuration. d Follow the on-screen instructions until this screen appears. Choose your machine from the list, and then click OK. Wireless Network Note • You can find your machine’s MAC Address (Ethernet Address) and IP Address by printing out the Network Configuration Report. See Print the Network Configuration Report on page 32. • If this screen appears click OK. Enter a name for your Macintosh in Display Name up to 15 characters long and click OK. Go to step e. • If you want to use the machine’s SCAN key to scan over the network, you must check the Register your computer with the "Scan To" function on the machine box. • The name you enter will appear on the machine’s LCD when you press (SCAN) and choose a scan option. (For more information, see Network Scanning in the Software User's Guide.) e Macintosh 13 Download and install Presto! PageManager When Presto! PageManager is installed OCR capability is added to Brother ControlCenter2. You can easily scan, share and organize photos and documents using Presto! PageManager. On the Brother Support screen, click Presto! PageManager and follow the on-screen instructions. 14 Install MFL-Pro Suite on additional computers (if needed) If you want to use your machine with multiple computers on the network, install MFL-Pro Suite on each computer. Go to step 12 on page 30. Finish The installation is now complete. When this screen appears, click Next. Note The installation of MFL-Pro Suite is now complete. Go to step 13 on page 31. If you use a specified IP Address for the machine, you must set the Boot Method to Static by using the control panel. For more information, see Network menu in the Network User's Guide. Windows® Macintosh Wireless Network 31 For Network Users Web Based Management (web browser) Print the Network Configuration Report The Brother print server is equipped with a web server that allows you to monitor its status or change some of its configuration settings, using HTTP (Hyper Text Transfer Protocol). You can print the Network Configuration Report to confirm the current network settings. Note • The default User Name is ‘admin’ and the default password is ‘access’. You can use a web browser to change this password. Microsoft® • We recommend Internet Explorer® 6.0 (or greater) or Firefox 3.0 (or greater) for Windows® and Safari 3.0 (or greater) for Macintosh. Please also make sure that JavaScript and cookies are always enabled in whichever browser you use. To use a web browser, you will need to know the IP address of the print server. The IP address of the print server is listed on the Network Configuration Report. a b Open your browser. Type “http://machine’s IP address/” into your browser’s address bar (where “machine’s IP address” is the IP address of the printer or the print server name). For example http://192.168.1.2/ a b c d e Press Menu. Press a or b to choose 5.Machine Info. Press OK. Press a or b to choose 4.Network Config. Press OK. Press Start. The machine will print the current network settings. f Press Stop/Exit. Restore the network settings to factory default To restore all network settings of the internal Print/Scan server to factory default, please follow the steps below. a b c See Web Based Management in the Network User's Guide. Turn the machine on and wait until it is in the Ready state. d e f Make sure the machine is not operating, then disconnect all the cables from the machine (except the power cord). Press Menu. Press a or b to choose 4.Network. Press OK. Press a or b to choose 0.Network Reset. Press OK. Press a to choose Reset. Press a to choose Yes. The machine will restart, re-connect cables once this is complete. 32 Other Information Brother CreativeCenter Get inspired. If you're using Windows, double-click the Brother CreativeCenter icon on your desktop to access our FREE web site with many ideas and resources for personal and professional use. Mac users can access Brother CreativeCenter at this web address: http://www.brother.com/creativecenter/ 33 Consumables Consumables When the time comes to replace consumable items, an error will be indicated by the LCD on the control panel. For more information about the consumables for your machine, visit us at http://solutions.brother.com/ or contact your local Brother reseller. Toner cartridges Drum unit Standard Toner: TN-420 High Capacity Toner: TN-450 DR-420 For replacing the consumable items, See Replacing consumable items in the Basic User’s Guide. 34 Trademarks The Brother logo is a registered trademark of Brother Industries, Ltd. Brother is a registered trademark of Brother Industries, Ltd. Microsoft, Windows, Windows Server and Internet Explorer are registered trademarks of Microsoft Corporation in the United States and/or other countries. Windows Vista is either a registered trademark or a trademark of Microsoft Corporation in the United States and other countries. Apple, Macintosh, Safari and TrueType are trademarks of Apple Inc., registered in the United States and other countries. Mac and the Mac logo are trademarks of Apple Inc., registered in the U.S. and other countries. Wi-Fi and Wi-Fi Alliance are registered trademarks of the Wi-Fi Alliance. AOSS is a trademark of Buffalo Inc. Nuance, the Nuance logo, PaperPort and ScanSoft are trademarks or registered trademarks of Nuance Communications, Inc. or its affiliates in the United States and/or other countries. Any trade names and product names of companies appearing on Brother products, related documents and any other materials are all trademarks or registered trademarks of those respective companies. Compilation and Publication Under the supervision of Brother Industries, Ltd., this manual has been compiled and published, covering the latest product descriptions and specifications. The contents of this manual and the specifications of this product are subject to change without notice. Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other errors relating to the publication. Copyright and License ©2010 Brother Industries, Ltd. This product includes software developed by the following vendors: ©1983-1998 PACIFIC SOFTWORKS, INC. ©2010 Devicescape Software, Inc. This product includes the “KASAGO TCP/IP” software developed by ZUKEN ELMIC, Inc.