Download Windsor TC17/2OlFE Operating instructions

TRIDENT COMPACT 17" 230V/240V
Page 1 of 27
rn
W
WINDSOR
H A R D F L O O R S C R U B B E R
Operating Instructions (ENG)
MODEL:
VOLTAGE
-
TC17/2OlFE (17'/20" Non-Traction)
Q-sr ...
for continuous lmprovrman,
Windsar'r Pwlity ManagemantSystem is Cerh'fied IS0 9Opl
230V
C€
I
IPX4
__
_____
~
Read these instructions before operating the machine.
TCE20-IF 98461 12-01-99
TRIDENT COMPACT 17" 230V/240V
Page 2 of 27
ENGUSH
IMPORTANT SAFETY INSTRUCTIONS
When using an electrlcal appliance, basic precautionsshould always be followed, including the following:
A WARNING:
TO reduce the risk of fire, electric shock, or iniuw:
Connect machine to a properly grounded outlet only. See grounding instructions.
Do not leave appliance when plug ed in. Unplug from outlet when not in use and before sewicing.
Do not use outdoors or on wet sufaces.
Do not allow to be used as a toy. Close attention is necessary when used by or near children.
Use only as described in this manual. Use only manufactures recommended attachments.
Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors,
or dropped into water, return it to an authorized service center.
Do not pull or carry by cord, use cord as a handle, close a door on a cord, or pull cord around sharp edges or corners.
Do not run appliance over cord. Keep cord away from heated surfaces.
Do not unplug b pulling on cord. To unplug, grasp the plug, not the cord.
Do not handle p& or appliance with wet hands.
Do not put any object into openings. Do not use with any opening blocked; kee free of dust, lint, hair, and anything that may reduce air flow.
Keep hair, loose clothing, fingers, and all parts of body away from openings animoving parts.
Do not ick up an hin that is burning or smoking, such as cigarettes, matches, or hot ashes.
Turn ofpall controg bekre unplugging.
Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.
SAVE THESE INSTRUCTIONS
SPANISH
INSTRUCCIONES IMPORTANTES PARA SU SEGURIDAD
Durante la utllzecl6n tie un dlspositivo electrico hay que tener en cuenta una serie de medldas basicas de precaucl6n, que
incluyen las sigulentes
A ADVERTENCIA: Para reducir el riesgo de incendios, descargas electricas o lesiones:
Nodeje nunca el aparatoconectado a la red. Despues de su USO, y antes de cualquier revisiono reparaclon. desconecte el aparato de la toma de corriente.
No usar nunca el aparato al aire libre, ni sobre superfivies humedas.
No penita que se utilice el aparato como un juguete. Hay que prestar especial atencion al utilizarlo en las cercanias de ninos.
Utilzar el aparato solo como se describe en este manual. Emplear exclusivamente 10s accesorios recomendados por el fabricante.No poner en marcha el
aparato con un cable electrico deteriorado. Si el aparato no funciona como deberia, si se ha caido, danado, si ha permanecido al sire libre o si se ha caido
a1 agua, dirijase a un taller de servicio.No tire del aparato ni lo transporte utilzando el cable electrico; no use el cable a modo de asa, ni cierre una puerta
con el cable pillado; no tienda el cable en torro a aristas vivas o esquinas.
Nopase con el aparato por encima del cable. Manten a el cable simpre lejos de superficiescalientes.Nodesconecteel enchufe de la red tirando del cable.
Para desconectar el aparato hay que tirar del enchuk, no del cable.
No maneje el enchufe ni el aparato con las manos humedas.
No inlroduzca ningun objeto en las aberturas del aparato.
No utilice el aparato mientras esta bloqueada uns de las aberturas; evite la penetracion de polvo, hilachas, pelos o cualquier objeto que pueda inhibir la
circulacion del aire.
Mantengasu cabello, la ropasuelta, Ios dedos y todas las partes de su cuerpo alejadas de las aberturasy piezas en movimiento.No utllice el aspiradorpara
recoger cuerpos en llamas o humeantes, tales como cigarrillos, cerillas o cenizas calientes
Desconecte todos 10s interruptores antes de desenchufar el aspirador..
No utilice el aspirador para recoger liquidos inflamableso combustibles, tales como gasollna, ni maneje el aspirador en zonas donde pueda haber liquidos
de este tiao.
FREEJCH
IMPORTANTES
MESURES DE SECURITE
Cutillsation d'un apparel1 Clectrlque demande certaines prkautions:
LIRE TOUTES LES INSTRUCTIONS AVANT DE FAlRE FONCTIONNER (CET APPAREIL)
A AVERTISSEMENT:
Pour r6duire les risques d'incendie, de choc dlectrique ou de blessure:
Cet appareil ne doit &re connecter u a des prises ayant une sortie de terre. Se reporter aux instructions de mise B la terre.
Ne pas laisser I'appareil sans surfellance lorsqu'il est branch& Debrancher lorsque I'appareil n'est pas utilise et avant I'entretien.
Avertissement. Pour reduire les risques de choc electrique, ne pas utiliser A I exterieur et ne pas aspirer de matibres humides.
Ne pas permettre aux enfants de jouer avec I'appareil. Une attention particulibreest necessairelorsque I'appareil est utilisd pardes enfants ou 6I proximite
de ces derniers.
Nutiliser que conform6ment B cette notice avec les accessoires recommandes par le fabricant.
Ne as utiliser si le cordon ou la fiche est endommage. Retourner I'appareil 6I un atelier de &paration s'il ne fonctionne pas bien, s'il est tomb6 ou s'il a Bt6
endbmmagb, oublib B I'exthrieur ou immerg6.
Ne pas tirer soulever ou trainer I'appareil par le cordon. Ne pas utiliser le cordoncomme une poignee, le coincer dans I'ernbrasure d'unbe porte ou I'appuyer
contre des arbtes vives ou des coins. Ne pas faire rouler I'appareil sur le cordon. Garder le cordon B I'6cart des surfaces chaudes.
Ne pas debrancher en tirant sur le cordon. Tirer plutdt la fiche.
Ne pas toucher la fiche ou I'appareil lorsque vos mains sont humides.
Ninserer aucun objet dans les ouvertures. Ne pas utiliser I'appareil lorsqu'une ouverture est bloqu6e. S'assure que de la poussibre, de la peluche, des
cheveux ou d'autres matibres ne reduisent pas le debit d'air.
Maintenir les cheveux, les vhtements amples, les doigts et toutes les parties du corps 1'6cart des ouverlures et des pihces mobiles.
Ne pas aspirer de matieres en combustion ou ui degagent de,la furnee, commedes cigarettes, des allumettes ou des cendres chaudes.
Mettre toutes les commandes B la position A R k T avant de debrancher I'appareil.
Ne pas aspirerdes liquides inflammablesou combustibles, comme de I'essence, et ne pas faire fonctionner dans des endroits oh peuventse trouverde telS
Iiquides.
CONSERVER CES INSTRUCTIONS
2
TRIDENT COMPACT 17" 230V/240V
Page 3 of 27
GERMAN
WlCHTlGE SlCHERHElTSHlNWElSE
-
Beim Gebrauch eines elektrishen Geriites mussen immer arundsiitzliche Vorsichtsma8nahmen beachtet
werden, elnschiieBiich der folgenden.
WARNUNG: Urn feuer; stromschlag oder beschadigungzu vermeiden:
A
Maschine nicht unbeaufsichtigtlassen. Bei Stillstand und Wartung Stecker ziehan.
Nicht irn Freien oder auf n&n Oberflache benutzen.
Die Maschine darf nicht als Spielreug benutzt werden. Besondere Aulmerksamkeit ist geboten, wenn die Maschine in der NHe von
Kindem benutzt wird.
Benutzung nur gemas Betrlebsanieltung und rnit dern vorn Hersteller emmmpfohlenen Zubehbr.
MaschlnenicM mii beschhdigtem Kabel oder Stecker inbetrlebnehrnen.Arbeitet die Maschlne nicht einwandfrei, ist sie hingefallenrnbeschidigt, hat sie
irn Freien estandenoder ist sie rnit Wasser in Berirhrunggekommen Kontakt mlt elnem aut?risierten Wartungsdienst aufnehmen.
Nicht am &be1 ziehen, Kabel nicht als Tragegriff benutzen, nicht in der Tore einklemmen oder uber scharfe Ecken und Kanten ziehen.
Nlcht rnlt der Maschine irber das Kabel fahren und Kabel von heisen Flachenfernhalten.
Stecker nicht am Kabei herauszlehen, sondern am Stecker.
Maschine und Stecker nicht rnit naBen HBnden bedienen.
Nlcht der Maschlne arbelten wenn irgendeineLiiftung blockiertist. Luftungsbffnungenfrei von Uberresten halten, welche die Lutrirkulationbehlndern.
Haare, lose Kleldung. Finger und alle anderen Kbrperteile von Offnungen und arbeltenden Teilen fernhalten.
Nichts brennendm oder ualrnendeswle Zigaretten, Streichhblzer oder heiae Asche aufsaugen.
Bevor Stecker gezogen drd, Maschine ausschalten.
Keine brennbaren oder entzirndbarenMaterlalienwle Benain aufsauaen und nkhi in deren Niihe arbelten.
-
BEACHTEN SIE DIESE HINWEiSE
NORWEGIAN
VlKTlGE SIKKERHETSINSTRUKSJONER
Ved bruk av elektrlsk utstyr skal dlsse grunnregler fslges:
ADVARSEL: For h unng6 fare for brann, elektrisk strat, elter skade:
A
Maskinen mA kun tilkobles et jordet uttak. Se jordin sinstruksjonene.
lkke forlat utstyret n& det er lnnkok$et. Dra ut stnpskt nfir det lkke brukes og ved reparasjon.
M i ikke brukes utendars eller & vatt underlag.
Ma ikke brukes sorn Iekem. &Id neye oppsyn ved bruk av og rundt barn.
Brukes kun siik det er forkiart I denne rnanualen. Bruk kun produsentens anbefaltetlil guts
lkke bruk skadet ledning eiler stnrpsel. Hvis utstvret ikke virker slik det skai, har falt i b a e n , %t skadet, forlatt utend~lrseller rnlstet ivann, returner det
ti1 en autorisert r am&.
lkke dra eller IdtTedningen, bruk heiler ikke ledningensorn hdndtak. ikke lukk en dar over ledningen, heller ikke dra ledningen rundt skarpe kanter eller
hjramer.
lkke 0r apparater over lednin en. Hold ledningen borte fra oppvarrnet underia
lkke I r a ut strapelet ved 6 dra ifedningen, For h dra ut stapslet.
ta tak i stopslet, Eke i ledningen.
.
lkke hhdter sbpslet eller utstyret r n d v&e hender.
lkke stlkkfrernmedlegernerinn 1 Hpningene. MA ikke brukes hvis noen av hpningene er blokkerte: hold rent fo stprv, lo, h&, og annet sorn kan redusere
luftstraprnen.
Hold har, lase klaer, fin rer og alle kroppsdeler vekk fra &ringer og bevegelige deler.
lkke su opp me sorn%renner eller nayker, slik som sigaretter, fyrstlkker eller varm aske.
Sib av %ie kontrolier far strawlet dras ut.
lkke sug opp brennbaredler lettantemmeligevresker slik sorn bensln, eller bruk I omiader hvor dlsse kan forekomrne.
TA VARE PA DISSE INSTRUKSJONENE
ITAWN
IMPORTANTI ISTRUZIONI PER LA SICUREZZA
Quando si us8 un apparecchiatura eiettrica, e necessario sempre aicune precauzioni di base, fra cui:
A AVVERTENZA: Perridurre il pericoto di incendio, scosse elettriche e lesioni personali:
Collegare la rnacchina soiarnente ad una presa di corrente adeguatamente rnessa a terra. Vedere le istruzlonl sulla me858 a terra.
Non abbandonare la macchinaquandoquestaBcollegataalle presadl corrente.Quando lamacchinanon viene usata, e primadi ognl lnterventodl rlparazione o rnanutenzione, staccare iIcavo dl alirnentazione dalla pressa di corrente.
Non usare la rnacchlna all'aperto o su supemcl bagnate.
Non permettere che la macchina venga usata come giocattolo. Prestare patticolareattenzione quando la macchlna viene usata dai bambini o vicino ad
essi.
Usare la macchina soltanto nel modo descritto in questo manuale. Usare solamante accessori raccornandabidalla casa produttrice della rnacchlna.
Non usare ia rnacchina con cavi e spine danneggiatl. Se la rnacchina non funziona come dowebbe, B caduta a terra, si B danneggiata, B stata ladata
ail'aperto o B caduta in acqua, portarla ad un centro assistenza autorimto.
Nonfrare o trasportare la macchlna per iIcavo, nB usare II cavo come rnanico. chiudere una porta sopra ilcaw,tirare ilcavo a contatto di angoll e bordi
acurninati.
No usare la macchina in rnovimento sopra il cavo; tenere il cavo il cavo lontano da superfici caide.
Non staccare la 8 ina dalla resa dl correnteUrando II cavo. Per staccare ia spina, afferrare la spina e non 11 cavo.
Non maneggiare splna o macchina con ie rnani bagnate.
Non infilarealcun oggetto demo le aperture. Non usarela rnacchinase un'apertura b bloccata; rnantenerela rnacchinaprivadipoivere,sporco, sfilacciature o altro ostacolo che riduca ilfiusso dell'aria.
Tenere capelli, abti ampi, dlta e ognl altra patte del corpo lontano dalle a etture e dalle partl in movlrnento.
Non usare l'aspirapolvere per raccogiiere qualcosa che stia bruciando o Ernando (sigarette, fiarnrniferi, caneri calde).
Prima di staccare la spina dalla presa di corrente, spegnere tutti i cornandl delia macchina.
Non usare la rnacchina per raccogiiere liquidi infiammabilio combustibili, come la benzina, n4 usarla in aree dove possono esservi tali liquidi.
CONSERVARE QUESTE ISTRUZIONI
TCEX-IF OBIBl 7Ilh?7
3
TRIDENT COMPACT 17" 230V/240V
Page 4 of 27
ELECTRICAL:
mls machineoperatesona standard230VoltACcircuit. Voltagesbelow220Volts orabove250 voltscouldcauseseriousdamage to moron.Wiringdragram is mountedinsideofmachlne.
EXTENSION CORDS:
If an extenalon cord Is uaed. the wlre air0 muat be al IQBIt on e size larger than the power cord on the mechlna, and rnwt be Ilmlted to 50 feot (15.15m) In length. NOTE:
H the p o w supply cord of this appllame Is damaged, it must be replacedby a special cord.
Improper connectlon of the equipment-groundingconductor can result in a rlsk of electric shock. Check with
a qualified electrician or service person if you are in doubt as to whether the outlet Is properly grounded. Do not
modifythe plug provldedwlth theappliance-If ltwlll notflttheoutlet, haveaproperoutletlnstaiiedbyaquallfiedelectricicm.
1NSPECTION:Carefullyunpackyourmachineandinspect it lorany shippingdamage. Any damagewhichoccurreddudng shippingistheresponsibilityofthecanier,whomustben~tifled
immediately.
ELECTRICIDAD:
Esta aSprradomfunciona en un clrculto combnte de 230 voltios CA. Los voltajks
. .wr debalo de 220 wltlbs o Dor e d m a de 250 voltlos wdrian ocasionar serios datlos a 10s motoms.
€1 dlagmna de cableado esta montado den de la mdquina.
CORDONES DE PROLONGACI&:
SI se utilize un cordbn do prolongaclbn, el tarnah del cable Uebe ser por lo rnenos de un tern& mba gnnde quo el dd cordbn do electrlcldad de la mAqulns y t i w e quo
estar llmltado a 50 pies (15,18 metro.) de longltud. NOTA: SI el cord& do 8iectriCidod do 88108rtsieeto se dM8, hay que tvemplsuarlo con un corddn mpscl.l.
La conexi6n indebida del conductor a tierra del equipo puede dar como resultado un riesgo de choque el6ctrlco.
Consultarcon une personade serviclo oelectriclsta calificado si se tlene dudas respecto de sl la toma est4 puesta
a tierra en forma apropiads. No modificar el enchufe qua viene con el artefact0 3/4 si no se ajusta a la toma do
corriente, hacer qua un electriclsta callficado Instale la toms apropiads..
INSPECC16N: Desempacar cuidadosamentela aspiradora e inspeccionarlapara ver si hasufrido deflosen el transporte. Cualquier dailo que haya tenido lugar durante el traslado es
responsablidadde la empresa de transportes. a la que hay que notificar en forma inmediata.
SPECIFICATIONS ELECTRIQUES:
Cat aspirateur fonctionne swtensionaltemativade230voRs. Destenslonsinf6deures A220 volts ou sup6rlaurs A 260volls peuMntserieusementendommagwlermoteun. Le &%ha
du chblage 88 trwve B I'int&ieur do la machine.
RALLONGES
Slunerallongeeatutll~,LatallleducardonBledrlqued~~tBbeau
mol~d'unetaillseupBrleurh~~ui
delamachlneeysalongeurllrn~B15rn.NOE:~lecwdond'alImnta~en
cowMt de cet 4ppareil srrt endomma&, fl doil8tre m p l a c d par un cordon sp6cial.
Une connexlm non conforme du conductour do mire h I8 terre do I'appamll p u t provoqurr une d6 charge
6Iectrlque.Consulter un 6lecirlclen quallfl6 ou une pemonne du rervlce aprh wnte rl voua ruspcmz
que la p r b de courant n'est pa8 correctemant mire h la tern. No per modltler la flche fournle avec
I'ap are11 a1 elle ne rantre par danr la prise, falter Installer une prise apprroprlb par un 6Ioctrlclrn
quaEfi6.
-
INSPECTION Mballer soigneusement I'aspirateur et I'inspecter pour tout dornmage du au transport. Tous dBg,ts qui onteu lieu pendant le transportcront Bla nwponsabilit6du t r a m
portwr, qui doit &re mis au courant irnm6diaternrnent.
ELEKTRISCHE ANFORDERUNGEN
-
Di%serStsub8fiugerHlird rniteinnemStandard 230VoltAC-Stromkreis betrieben. Spannungenunter220Voltoderikber250Voltk(lnnenzuschwerenBesch&digungendw Motown
firhmn. Ein Sohaltplan iat im lnnem des Qarbts angebrecht.
VERLANGERUNQSKABEL:
~~*nVeflbgerUngrlcclbel
benut2t, aomu8deasm Kabdgr68eg~eralSdmKabelgrMedesStrornkatusderMaschlnedn, DasVerl&nge~ngskabaldarfnlcMI8ngerab
15,15rn
wln. HIWEIS: Sol& d a Stmmkabd dbes Gen4ts beschddigt aefn, 80 mu8 8s dun% eln spezldles Kebel emta M e n .
Eln fehlerhatkr Mrbinden der Erdleltungdes G e r h kann StromrchlBgeverureachen. Kontaktkren Sle elnen
qu8llflderten Elektrlker odor Kundendlenstpenonal, falls 810 nlcht genau wiimn, ob dle Stockdore rlcMlg
geerdel I d Veriindern Sie nlcht den mlt d m Ge& mltgell.1rrt.n Stocker. PaBt der Stocker nlcht In dle
Steckdow, 80 luwn Sle von elnem quallfhlerlen Elektrlker n
i..
passonde Steckdose Instatlleren.
INSPEKTIONDasGerBtvonicMlgauspckenuK1aufTransportschddenuntersuchen.FikrSchBden,die belrnVersandaufge(retenelnd.i~derSpedlteur~rantwomich,
unddieserbt
sofort ;EU benachrichtigen.
SPECIFICHE ELETTRICHE:
Ouestoaspimpolvere funziona con un wrcuito elenriw standardCA da 230 Volt Tensionlinterioria220 Volt o superioria 250 Voltpossono causaregravi dannia1rnotore 11 diagramma
del co/iegamentl elettriclsl tmva dentro la macchina.
CAW DI ESTENSIONE:
Se vlene uaato un cavo dl eatenalone. la dimmsione del fllo deve essere alrneno dl una misun rnaggloredeI cavo dl eltmentazlone della macchlna e non PIP lungo di 15.1 5
rnetri. NOTA: Se / I cavo dialfmentazione diquhsn mecchin8 4 danneggiato, sostftufrfo con un cavo specl.lr.
L'errato collegamento del filo di terra della macchina pub causare II rischio di scosse elettriche. In caso di
dubbi s u b correttezza della mersa a terra della prera di corrente, rivolgersi ad un elenriclsta qualificato o
ad un tecnlco delle rlparazlonl. Non modificarela spina coneegnata con la macchina: r e la spina non entra nella
presa, far installare da un elettricista quallflcato une corretta presa dl corrente.
VERIRCA Con anendone, disimbellare I'aspirapolvere ad ispezlonarlo per veriflcare I'assenze di danni causati dalla spedizione I danni eventualmenle risultanti sono response
bilita dello spedlzionere il quale deve essere awertito tmrnediatamente..
ELEKTRISK:
Dette apparatet operereepl en standard230 Volt vekselstmmkrets. Spennlngunder220 Volt eller over 250 Volt kan fodsake alvoriigeskaderp4 motorer. KobllngssQema er montert
p4 innsidenav rnasklnen.
FORLENGELSESLEDNING:
Hvi8 en forlengeisbdning er brukt, mi Iedningens sWrreise bare minst6n sWrrefse s*rre enn stmmfedfngenpd maskfnen,og mi b e g m a s ti150 fot (15.15m) I fengde.
NBI Hvls stmmledningenpd d.tt0 appaIotot or skadet, d den byltes ut med en speslalledning.
Hvis utstyret lkke jordes korrekt, ken det medfere fare for elektrisk stet. KonWoller med en kvalifisert elektriker eller
reparawr hvis du or itvil med hensyn tll om stikkontaktencr riktlg iordet. lkke modifis6r stepslet som apparatet er
utstyrt med hvis det lkke passer I uttaket, fa et riktig uttak innstallert av en kvalifisert elektriker.
-
INSPEKSJON: Pskk opp din smsuger foniktig og insplsbrden for fraktskader. Skader som har skledd under frakien, er senderen ansvarlig for og mA bli underrenetumlddelbart.
4
TcE2o-/Fo(lldl 711197
TRIDENT COMPACT 17" 230V/240V
Page 5 of 27
SAFETY
The following symbols are used throughout this
guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
WHEN TRANSPORTING MACHINE IN A
TRAILER:
rn
Make sure the ramp angle is no more than
lo', and the ram is strong enough to
support the milc ine.
Make sure ramp is clean and dry.
Put ramp into position.
Remove squeegee assembly & brushes
before loading.
Align the machine on a level surface ten
(10) feet behind the ramp.
Push machine up ramp carefully.
Securely fasten the machine to the trailer.
R
There are three levels of hazard intensity identified by signal words -WARNING, CAUTION
and FOR SAFETI! The level of hazard intensity
is determined by the following definitions:
WARNING - Hazards or unsafe practices which
COULD result in severe personal injury or death.
0
THIS PRODUCT IS FOR COMM€RCfAL USE ONLX
CAUTION - Hazards or unsafe practices which
could result in minor personal injury or product or
property damage.
Notes:
FOR SAFETY: To Identity actions which must be
followed for safe operation of equipment.
The following information signals indicate potentially dangerous conditions to the operator or equipment. Readthis
guide carefully. Know when these conditionscan exist. Locate all safety devices on the machine. Report machine
damage or faulty operation immediately. Do not use the
machine if it is not in proper operating condition.
For SAFE7X
DO NOT OPERATE MACHINE:
Unless Trained and Authorized
Unless Operatlon Gulde is Read and
understood.
0
In Flammable or Explosive areas.
rn
rn
WHEN USlNG MACHINE:
rn
Go slow on grades and slippery
surfaces.
rn
Use care when backing machine.
rn
Do not carry rlders on machine.
0
Always follow bask safety and
traffic rules.
BEFORE LEAVMG OR SERVlClNG
MACHINE:
rn
rn
Stop on level surfaces.
Turn off machine.
WHEN SERVICING MACHINE:
rn
Avoid moving parts. Do not wear loose
jackets, shirts, or sleeves when working on
machlne.
rn
Block machine wheels before jacking
machine up.
0
Use holat or jack of adequate capacity to
0
lltt machine.
Use Windsor approved replacement
parts.
TCE20-IF 98461 7/1/97
5
Page 6 of 27
TRIDENT COMPACT 17" 230V/240V
SAFENIOPERATIONS
INSPECTION: Carefully unpack your scrubber and
a
inspect it for an shipping dama 8. Any damage
which occurred &ring shipping is t e
HOW IT OPERATES
The TRIDENT COMPACT is a walk-behind scrubber.
The main scrubbin components include a solution/
recovery tank, sing e disc-type brush or pad, a rear
squeegee and a vacuum motor.
Detergent solution and water flow from the solution
tank to the scrub brush. The rotating brush scrubs the
floor. As the machine moves forward, the rear squeegee collects the dirty solution and channels it into the
vacuum of the squeegee pickup hose. The pickup
hose deposits the dirty solution into the recovery tank.
B
PREPARING FOR OPERATION
(PERFORM DAILY MAINTENANCE AS SHOWN ON
PAGE8.)
Fill Solution Tank
Remove cover and fill. (see item 19, page 14)
1.)
Use a clean bucket or hose to fill the tank
2.)
with water.
~-
D o o t use watertemperatures in excess of 140" F(60"
C). Water which is too hot may distort the polyethylene tanks.
3.) Add a cleaning concentrate for use in automatic
floor scrubbers. Closely follow the manufacturer's instructions found on container. Read ingredients listed on the
container to ensure compatible chemicals are used.
Use only the suitable chemicals listed below.
Using incompatible chemicals may damage
the machine. Dama 8s of this type are not coverad under the WlrSbSOR Three Year Protection Plan. Carefully read ingredients on
manufacturer's label before using any product
in this machine.
b
I
SUITABLE
CHEMICALS
INCOMPATIBLE
CHEMICALS
Alkalis
Defoaming Agents
Aldehydes
Carbon Tetrachloride
Chlorinated Hydrocarbons
Methyls (MEK)
Detergents
Hydroxides
PREPARING FOR OPERATION (Cont.)
Plug the power cords together and twist into
locked position. Attach the power cord to the yellow
strain relief as shown. Plug power cord into a properly
grounded wall outlet.
4.)
Turn vacuum motor switch on and off to make
sure there is electrical power at machine.
5.)
OPERATING THE MACHINE
(PERFORM DAILY MAINTENANCE AS SHOWN
ON PAGE 8.)
1. The area to be scrubbed should be swept, dry
mopped and clear of debris (paper plates,
cups, etc.).
2. Adjust the operator control handle to a
comfortable position. (see item 3,page 7)
3. Release solution. (Pull solution control lever
rearward.) (see item 6, page 7) NOTE The
amount of solution can be regulatedduring
operation depending on the Zype of floor and
the traverse speed of the machine. Pulling the
lever farther rearwardreleases more solution.
4.
Switch on brush drive motor. (see item 1,
Page 7 )
5. Switch on vacuum motor. (see item 2, page 7)
6. Lower scrub deck. Pull scrub deck Mt lever
rearward. (see item 8. Dane 7l
Do not leave brush running on floor whlle machine is stationary.
7. Lower squeegee. Pull squeegee lift lever
back. (see item 7, page 7) NOTE Adjust
squeegee as shown on page 10.
8. Move machine forward by applying even
pressure on the main handle. Forwardmotion
is assisted by the scrubbing action of the
brushlpad driver.
+---
--1
- +- - - - - -
- +-----
Perchlorethylene(per)
Phenols
Trichlorethylene
D-Limonene
rke extra care not to run machine over cord
or catch cord on squeegee when turning.
9. Plan your cleaning route to work away from
the electrical source. Move machine forward
at a steady pace.
TCE20-IF 88461 7/1\97
TRIDENT COMPACT 17" 230V/240V
Page 7 of 27
OPERATION CONTROLS
6
7
Brush Switch. Turns brush onloff.
2
Vacuum SwNch. Turns vacuum
motor onloff.
3
Main Handle.
4
Brush Motor CIrcuit Breaker.
Protects brush motor from overheating.
5
Vacuum Motor Clrcuit Breaker.
Protects vacuum motor from overheating.
6
Solution Lever. Controls the amount of
solution flow to the floor.
7
Squeegee UftLever. Raises and
lowers squeegee.
8
Scrub Deck Lit#Lever. Raises and lowers
scrub deck.
9
Recovery Wnk Drain nose.
TOP VIEW
\
.7
BACK
4
4
5
70 Solution Tank Drain Hose.
b
7 7 Squeegee Release Latch. Releases
the rear squeegee blade for adjustment
or replacement.
a
72 Battery Compartment Door Latch. Opens
back of machine for access to batteries.
73 Vacuum nose.
'2
73
/
'
ull =
_I1
72
/ 70
\ \-
I
0
1
TEC20-IF 98461 7/1/97
7
Page 8 of 27
TRIDENT COMPACT 17” 230V/240V
MAINTENANCE
Maintenance Item
Weeklv
Monthlv Annuallv
*
*
*
*
Inspect Vac Fan Foam Breaker - * Inspect power cord for wear. __
Check Vac Hose Connections Clean the Squeegee Blades
lnsoect Brush or Pad
Before Starting
the Work Period
0
End of Work
@
Period Before
Storing
@
0
NOTE:
Dailv
6
@
8
*
Drain & Rinse Tanks
*
*
a
Damane and or wear
Clean Squeegee Blades &
Foam Break6
Remove lint build-up from screen
in the recovery tank well.
Remove tank lid and allow recovery
to dry between uses.
Check Solution Strainer
Check Casters & Wheels for
proper lubrication
Inspect Tanks and Hoses
Inspect all Motors for Carbon
Motor Brush wear.
*
*
*
*
-
*
-
*-
*
Details on these maintenance items can be found on the following pages.
This cable will lay on wet surfaces. To prevent electrical shock
immedlafely replace cords with frayed or cracked insulation.
Periodicaily inspect the recovery tank and decontaminate if necessaw
using a Hosprtai Grade Virucide or a 1 10 bleach to water solution.
Wastewater should be disposed of properly.
Occasionally check in line filter screen, rinse with hot water if necessary.
Frayed or cracked hoses should be replaced to avoid vacuum or solution
pressure loss.
-
LUBRICATION:
The following symbols are found throughout the manual indicating the
items requiring lubrication:
Apply Grease
EXAMPLE:
Use Spray Lubricant.
/
Thread Locker (Red or blue).
SEIZE
8
Use Anti-Seize when repairing.
-1
11/25/98
TRIDENT COMPACT 17" 230V/240V
Page 9 of 27
MAINTENANCE
VACUUM
MOTOR
BRUSH
Unplug the machlne from outlet.
Remove (6) bolts holding vac motor/ plate
assembly to recovery tank.
3.
Disconnect vac motor lead from connector
and lift out vac motor/ plate assembly.
4.
Check motor brushes. When worn to 318" replace
both brushes.
After the machine has been used for any wet pick-up,
allow the vacuum motor to run 1-2 minutes, to help reduce moisture build-up in the vacuum motor. Drying
out the vacuum motor after each use will extend the life
of your vacuum motor.
1.
2.
1.
2.
Hazardous Voltage. Shock can result. Unplug
mahcine before servicing machine. Only
qualified personnel should work inside machine.
Import8nt:
When replacing
carbon vac motor
brushes loosen wire
terminal BEFORE removing screws on
bracket.
Wire Terminal
Brush Installation:
Slide brush or pad driver under drive plate.
Align one metal lug on the brush or
pad driver with the scrub deck sight hole
and a keyhole in the drive plate.
3. Raise the brush or pad driver upward
and twist clockwise until locked.
Brush Removal:
Raise brush or pad driver off floor.
Reach under brush or pad driver and rotate
so that the metal lug in the drive plate is
visible through the scrub deck sight hole.
3. Quickly twist brush or pad driver counterclockwise to
release.
1.
2.
SOLUTION STRAINER
1.
An inline solution strainer is located under chassis
behind left wheel. Remove sediment bowl and
screen periodically and rinse clean with hot water.
Be careful not to misplace the gasket.
Wire
Importsnt:
Replace carbon vac motor
brushes if worn down to 318" in
length. These brushes wear
quicker as the length shortens
due to increased heat.
Spring inside brush housing
will damage motor if brushes
are allowed to completely wear
away.
Note:
Place stop
In groove.
NOTE: Periodically check the length of the carbon
brushes. ReDlace carbon brushes which 8re less
han 3/8"lo&.
-
PART NO. 74695
TCEZO-IF 98461 7/1/97
U
9
Page 10 of 27
TRIDENT COMPACT 17" 230V/240V
MAINTENANCE
SQUEEGEE
ASSEMBLY
SQUEEGEE DEFLECTION
INCORRECT
Before and during use of machine, use a damp cloth to
wipe the outside and inside of squeegee to remove
buildup of foreign material on the squeegee blades.
This prevents streaking and residue on the floor.
Squeegee wear:
After extended use, the squeegee blades will wear. To
improve squeegee performance and extend wear, proceed as follows:
1.
Turn off all switches and place the machine
on a level surface. Raise the squeegee to
the transport position.
Loosen knobs on the left and right hand
2.
sides of squeegee until squeegee can be
removed from the squeegee bracket.
Loosen the fasteners on front of squeegee
3.
to replace or adjust front blade.
4.
Unlatch rear squeegee latch to replace rear
blade.
Adjusting Squeegee Assembly
1.
2.
3.
I NOTENOUGH
I
L
1
TOOMUCH
Lower the squeegee and move the machine
forward.
Obsetve the level of the squeegee for an
even curl along the length of the blade. Use
camber adjustment knob to achieve even curl if
required.
Adjust the down pressure nut located on
squeegee mounting assembly. Do not apply
excessive force.
TCE2O-IF 98481 7/1\87
TRIDENT COMPACT 17" 230V/240V
Page 11 of 27
TROUBLE SHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
SOLUTION
No power to
machine
Dead electrical circuit
Check building circuit breaker or fuse box.
Power switch failure
Replace.
Faulty power cord
RepIace.
Equipment not grounding
Follow grounding instructions exactly.
Receptacle not grounded
Contact an electrician to check building's wii ..ig.
Internal wiring problem
Have a trained service technician check machine's
wiring.
Electrical shock
Worn motor brushes
Vac motor speed
varies or doesn't run
Motor worn out
Loss of
Vacuum
Solution not
flowing properly
TCE20-IF 98461 7/1/97
1
Replace.
Replace.
Faulty switch
Replace.
Loose recovery tank lid
Center and seal dome over tank.
Crack in recovery tank lid
or poor joint
Replace or repair using acrylic plastic cement only.
Lint or dirt clogging
vacuum screen
With power off clean screen.
Loosecuffsonvacuum
hose
Tighten cuffs turning counterclockwise.
Vac motor seals leaking
Replace.
Floor tool vac chamber
clogged
Wash out with hose. Pick lint out with a wire.
Vac motor, hose, or
dome gasket
Replace.
Improper solution hose connection
Check for positive connection
Screen in filter clogged
Remove and clean with hot water.
Valve clogged
Clean or replace if damaged. Check to be sure
filter screen is in place. Be sure to premix cleaning
chemicals.
VACUUM SWITCH
I
SCRUB DECK
I
H
BRUSH SWITCH
BLU I
880 137
BLUE
0 000
I oI o o o
BROWN
BRN
GRN’YLW
VACUUM
MOTOR
L
FEAANREL
-
-m
I
BRN
80592
L
GRN/YLW
08539
GRN/YLW
88936
ENCLOSURE
6PANEL
N
TRIDENT COMPACT 17" 230V/240V
Page 13 of 27
PI
VAC MOTOR ASSEMBLY
WINDSOR"
4-
Ref
Qty.
P
PartNo.
Oescnption
Serial No.
To
Notes:
From
1
2
3
1
1
4
6
5
6
7
8
9
10
4
1
3
6
6
6
6
27519
53749
62360
70085
70114
73419
57030
70607
87018
87025
TCE20-IF 98461 7/1/97
COVER,VACMOTOR
VAC MTR ASM, 24OV 5.7 2ST. P/D
PLATEASM, PT17EVAC
SCR, 1/4-20 X 112 PHMS
SCR, #10 X 314 POLYFAST
SPACER,VACMOTOR
NUT, 10-32 NYLOCK PLTD
SET SCREW, 10-32 X 1.OO
WASHER, #lo X 9/16 OD
WASHER, 114STAR
13
Page 14 of 27
TRIDENT COMPACT 17”230V/240V
REAR VIEW
21
37
36
25
14
TCE20-IF 98461 12-01-99
Page 15 of 27
TRIDENT COMPACT 17" 230V/240V
TANKS AND PARTS LiST
I
REF
PARTNO.
QTY
SERIAL NO.
FROM
DESCRIPTION
TCE-IF 98461 12-01-99
NOTES:
15
TRIDENT COMPACT 17" 230V/240V
SQUEEGEE ASSEMBLY
Page 16 of 27
X?UEEGEE SUB ASSEMBLY
t
P
7
16
9
TC2OE-IF 98461 7/1/87
TRIDENT COMPACT 17" 230V/240V
Page 17 of 27
SQUEEGEE ASSEMBLY
2
3
1
I
140148
140149
BRACKETASM.SUPPORT
BLOCK,SPRINGSUPPOFIT
7
8
2
2
18039
27423
CASTER, SWIVEL 3.50 X 4.69
CAP, SPRING RETAINER
11
2
6
48069
5703
62629
1 6 4 0 9 0
1
66268
1
66272
1
66274
2
66275
1
24
25
26
27
28
29
4
3 0 1
31
1
67380
67355
70018
2.88 X 0.25 X 0.40 CABLE
PIN, CLEVIS 5/16 X 2.75LG ZINC
PLATE. SQUEEGEE ADJUSTMENT
PLATE WELDMENT, SQ. MOUNT
PIN CLEVIS, 1/4 X 1.625 LG
OPEN
RIVET, 532 OD X 118 GRIP ALUM
ROD. WFI DMFNT SQ. I IFT
SCREW,1/4-20XI HHCSSS
37
38
39
1
1
1
73854
78359
73802
SPRING COMPRESS 1.10 X 2.75 X .I
TUBE, 13/32 X 0.049W X 1.56L CRS
BLADE, SQ. TR20/24 DIE CUT FRONT
42
43
44
1
1
73804
78356
SQUEEGEE ASSEMBLY, TR20/24
SPACER, .314 X 5 9 X .36NYLON
OPEN
47
48
1
1
81488
81489
[
61
62
1 r9t.I
11
2
87029
I
CH, SQUEEGEE STRAP REAR
KER, SQUEEGEE STRAP REAR
ER, 5/16 FLAT SAE
~
WASHER,
0.5 X 1.25 FLAT GR8 PLTD
87090
WASHER, 5/16 SPLIT LOCK PLTD
WASHER, 114 ID X 3/4 OD PLTD
87137
89059
WASHER, YE" ID X 2" OD X 3/32 THK
WHEEL, PT20 SQUEEGEE BUMPER
~
~
TC2OE-IF 98461 7/1/97
17
TRIDENT COMPACT 17" 230V/240V
Page 18 of 27
VALVE ASSEMBLY
9
3
14
/ F A
-
18
23
Detall -A-
3
-\8 (FROM SOLUTION TANK)
\ 3 \ - 10 (SOLUTION DRAIN HOSE)
TC2OE-IF 08461 7/1/07
Page 19 of 27
TRIDENT COMPACT 17" 230V/240V
VALVE ASSEMBLY PARTS LIST
2
3
4
5
1
3
1
1
140146
20042
27372
27726
BRKT, SOLUTION VALVE MTG.
CLAMP,3/8HOSE
CAP,STRAlNER
CABLE,SOLUTION
I
~
7
8
9
10
11
121
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
1
1
1
39380
39381
39444
73383
2
40027
1
41184
5
1
57030
59021
1
1
1
1
1
1
70066
40013
70403
73405
78212
84143
9
1
87018
20035
28
29
30
TCE20-IF 98461 7/1/97
OPEN
HOSE, 112 ID NYLOBRAID 6"
HOSE, 1/2 ID CLEAR X 22"
HOSE, 112 X 5" CLEAR
OPEN
STRAINER, 3/8NPT 20 MESH
OPEN
HOSEBARB, 3/8 MPT X 112 90&
OPEN
HOUSING, STRAINER
OPEN
OPEN
NUT, 10-32 NYLOCK PLTD
O-RING, FILTER SEAL
OPEN
SCR, 10-32 X 3/4 PPHMS SS
HOSEBARB, 3/8 MPT X 112
SCR, #10 X 1/2 POLY. PH PHIL
SCREEN,80MESH
TEE, 3/8FPT
VALVE,3/0 FPT
OPEN
WASHER, # l o 9/16 OD
CLAMP, 7/16 DIA. NYLON UL
(ALL MODELS EXCEPT X)
19
TRIDENT COMPACT 17" 230V/240V
Page 20 of 27
SCRUB DECK ASSEMBLY
23
I
'
I
45
20
'31
TCE20-IF 98461 7/1/97
TRIDENT COMPACT 17” 230V/240V
Page 21 of 27
SCRUB DECK ASSEMBLY PARTS LIST
1B
2
3
4A
48
5A
59
6
7
8
49
50
51
52
53
54
55
56
57
58
59
60
61
62
1
2
3
1
1
1
1
4
1
1
20077
87090
48012
73790
73814
73422
73826
70266
57044
40027
CLAMP.WOkM#HS356
WASHER, i i 4 F L A - - KNOB,ADMHANDLE
SKIRT. SHROUD 3.25 X 58.0 L
SKIRT, SHROUD 3.25 X 49.0 L
SCRUBDECK,TC17
SCRUBDECK,TC20
SCR. 3/8-16 X 1.0 HHCS
NUT. 3/8 NPT HFX BRASS
HOSEBARB. 318 MPT X 1/290 DEG.
1
1
4
1
2
1
1
1
2
1
7
3
4
1
680143
89073
87025
88953
51166
57040
66192
05110
14664
67384
57047
70088
57028
57105
WIRE ASM, TC%F BRUSH MOTOR
WEIGHT, TCE COUNTER BALANCE
WASHER, 1/4 LOCK EXT STAR SS
WIRE. 18” GRN/MM 76010 X 76090
LINKAGE ASM. TC20 SEC ROD
NUT, 1/2NPTCONDUlT
PIN, ROLL1/4X1.25L
ARM ASM, SCRUB DECK
BUSHING, PRIMARY S.D.
RODASM,SCRUBDECK20
NUT,1/4-20NYLOCK
SCR, 10-32 X 1/2 PHMS
NUT, 10-24 TINNERMAN
NUT. 1/4-20 HEX W/STAR WASHER
TCE20-IF 98461 7/1/97
~
I
I
4
21
Page 22 of 27
TRIDENT COMPACT 17" 230V/240V
MECHANlCAL CONTROLS
24
-%
- 5
25
31
40
22
11
22
2\
-2
TCE20-IF 98461 7/1/97
Page 23 of 27
TRIDENT COMPACT 17” 230V/240V
MECHANICAL CONTROLS PARTS LIST
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
2
27413
1
1
1
1
1
1
3
27724
27725
27726
29151
36132
38208
48030
1
1
4
1
2
1
1
50742
51142
51184
51185
57006
57030
57032
1
1
2
3
1
2
2
1
1
1
1
1
66068
66073
66116
80604
66133
12
2
70228
70298
1
1
1
1
11
2
2
2
73236
73169
78220
87003
87018
87029
87030
87080
50
1
1
66270
70249
51
52
1
61320
66055
66257
67138
67224
67226
67360
67361
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
TCE20-IF 98461 7/1/97
CABLE, REAR COMPART. DOOR
OPEN
OPEN
CABLE,SCRUBDECK
CABLE,SQUEEGEE
CABLE,SOLUTlON
DOOR, REAR COMPARTMENT
GRI? HANDLE X 21.5”
HANDLE, PTCl7 W/ FOAM
KNOB,HANDLE
OPEN
OPEN
LABEL, SQUEEGEE WARNING
LEVER,HANDLECLAMP
LOCK, HANDLE ADJUSTMENT
LEVER,SOLUTlON
NUT,1/4-20HEX
NUT,10-32NY-LOCK
NUT, 3/8-16 SERRATED FLANGE
OPEN
PIN,118X5/8ROLL
PIN, 1/16 DIA X 314 L COTTER
PIN, 114x314 CLEWS
RING, RUE COTTER 1/4” PLTD
PIN, 3/16 X .88 L CLEVIS
PIN, ROLL114Xl.OL
PIVOT,CABLELEVER
RING, 318 EXTSNAP
ROD, HANDLEADJ.
ROD, CMPRTMNT DOOR LOCK
ROD ASM, SCRUB DECK LIFT
ROD ASM, SQUEEGEE LIFT
OPEN
OPEN
OPEN
SCR, 10-32 X 114 PHMS SS
SHOULDER BOLT, 5116 OD X 318 L
OPEN
SPRING, 1.12 COMPRESSION
I
STRAIN RELIEF. CORD HOOK
TUBE,HANDLEADJ.
WASHER, 318 ID X 718 OD
WASHER,#IOFLAT
WASHER.5116FLAT
WASHER, 318 X 314 NYLON
WASHER, 112”FLAT
OPEN
PIN CLEVIS, 3/16 X .75 L
SCR. 1/4-20 X 1.25 HHCS PLTD
OPEN
PANELASM, REAR
23
TRIDENT COMPACT 17" 230V/240V
Page 24 of 27
CONTROL PANEL ASSEMBLY
REAR VIEW
(CONTROL PANEL)
24
TCE20-IF 98461 7/1/97
Page 25 of 27
TRIDENT COMPACT 17" 230V/240V
CONTROL PANEL ASSEMBLY PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
2 9
3 0
31
32
2
1
1
1
1
8
2
3
2
1
1
1
3
16
2
1
10
2
1
2
1
1
8
1
1
1
2
2
1
1
2
3 3 2
34
1
3 5 2
140074
14520
14462
14279
42063
57049
57104
57106
57132
61342
67029
67382
70248
70394
72069
78374
87161
57047
57030
87090
50486
50487
57157
32042
87018
34243
57163
70245
32050
32051
70239
14942
35205
35206
TCE20-IF 98461 7/1/97
BREAKER.9AClRCUlT
__
CLIP, DRAiN HOSE
TERM. BLOCK, 25A 250V 1-1-2
BREAKER, 4AMP 230V CIRCUIT
lNLET,POWERlOA/250V
NUT,6-32NYLOCKSS
NUT, 10-32 WISTAR WSHR PLTD
NUT, 8-32 WISTAR WSHR PLTD
NUT, 3/8-27 DRESS PANEL
PANEL, CONTROL COVER
RECTIFIER, BRIDGE
RELAY DPST-NO30A
SCR, 8-32 X 1.O PHMS BLK NYL.
SCR, 6-32 X 112 THMS BLK
SWITCH, DPST 250V 16(6)A RCKF
TRANSFORMER ASM, 230V/24V
WASHER,#6FLATSAE
NUT, 1/4-20 NYLOCK PLTD
NUT, 10-32 NYLOCK PLTD
WASHER, 1/4-20 X 314 OD PLTD
LABEL,SQUEEGEE/SOLUTION
LABEL, SCRUB DECK
NUT, 6-32 U-TINNERMAN
ENCLOSURE, CONTROL PANEL
OPEN
WASHER, #10 X 9/16 OD
FILTER, EM1250V 8A 2.1 MH
NUT, 4-40 W/STAR WASHER
SCR, 4-40 X 314 PHMS PLTD
ENCL., SPLASHGUARD TOP
E
LASHGUA
s K 6 Z 2 x 314 P H 2
BOOT, 318 CIRCUIT BREAKER
GASKET, CONTROL PANEL
GASKET SWITCH SEAL
E: E
25
TRIDENT COMPACT 17" 230V/240V
Page 26 of 27
SCRUB DECKASSEMBLY (HEX DRIVE)
GROUPE TETE DE BROSSES (CENTRE HMAGONAL)
BRUSH
MOTOR
SCRUB
-
MOUNT2
1
4
5
3
6AB
Ref
Qly.
PadNo.
Description
1
2
3
4
5
6A
6B
1
1
29119
48040
70305
87029
87067
02327
81578
DRIVER, BRUSH
KEY, 1/4SQ. X 1.00
SCR, 5/16-18 X 314 HHCS PLTD
WASHER. 5/16 FLAT SAE
WASHER; 5/16 LCK I h S T R PLTD
PAD DRIVER ASM, 17" HEX DRIVE
PAD DRIVER ASM, 20" POLY
1
1
1
1
1
BRUSH AND PAD (17'7
OPTION LISF
PIN
02327
02323
02324
02325
DESCRIPTION
PAD DRIVER ASM, 17" HEX DRIVE
BRUSH, 17" NYLON DISK HEX DRIVE
BRUSH, 17" POLYPRO DISK HEX DRIVE
BRUSH, 17" GRIT DISK" HEX DRIVE
Senal NO.
From
To
Notee
BRUSH AND PAD (20")
0PTION LIS F
P/N
81578
81496
81497
81498
81499
81500
DESCRIPTION
PAD DRIVER ASM, 20" POLY
BRUSH, 20" POLY DISK
BRUSH, 20" NYLON DISK
BRUSH, 20" NYLON POLISH DISK
BRUSH, 20" MILD GRIT DISK
BRUSH, 20" SUPER GRIT DISK
TCE20-IF W 6 1 7/1/87
Page 27 of 27
TRIDENT COMPACT 17” 230V1240V
LIMITED WARRANTY
Windsor Industnes, Inc. warrants new machines against defects in matenal and workmanship
under normal use and service to the onginal purchaser. The warranty period is Subject to the
conditions stated below.
3 YEARS FOR PARTS AND 1 YEAR FOR SERVICE LABOR
Exceptions: Rotationally moldedpyethylene tanks carry a 6 year parts and 1 year service
labor warranty. VERSAMATIC models carry a 3 year warranty on brush motors, vacuum
motors, and belts, and a 1 year service labor warranty. SENSOR@models carry a 2 year
warranty on vacuum motors and belts, and a 1 year service labor warranty. Extractor brush
motors, pump motors, pc boards and electronics, vac motors (other than VERSAMATIC? and
SENSOR?, pumps, and FLEXSOLTMdiaphragms, all RADIUSTM, all AXCESSm and
TITANY carry a 1 year parts and setvice labor warranty. Propane equipment has a 1 year
parts and service warranty. The Onan@engines have a 3 year manufacturers’warranty. The
Honda@engines have a 2 year manufacturers’ warranty. The engine warranty is administered
through the engine manufacturer and must be repaired at an authonzed service center.
Normal wear items including, but not limited to, belts, brushes, capacitors. carbon brushes,
casters, clutches, cords, filters, finishes, gaskets, hoses, light bulbs, rectifiers, switches, s q u a
gees, bearings, pulleys, relays, actuating cables, tires and wheels will be warranted for
manufacturingdefects for 90 days from the purchase date.
The warranty commences on the purchase date by the onginal end user from an authonzed
Windsor Agent, subject to proof of purchase. The Machine Registration Card must be
completed and returned immediately at the time of purchase If proof of purchase cannot be
identified, the warranty start date is 90days after date of sale to an authonzed Windsor
distributor. Parts replaced or repaired under warranty are guaranteed for the remainder of the
onginal warranty penod.
90 DAY WARRANTY EXTENSION AVAILABLE
Upon receipt of the Machine Registration Card, Windsor will extend the warranty period an
additional 90 days from the purchase date. Does not include items warranted 90 days for
manufacturingdefects.
STATED WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED.
Any statutory implied warranties, including any warranty of merchantability or fitness for a
particular purpose, are expressly limited to the duration of this written warranty. Windsor will not
be liable for any other damages, including but not limited to indirect or special consequential
damages arising out of or in connection with the furnishing; performance, use or inability to use
the machine. This remedy shall be the exclusive remedy of the buyer.
This warranty shall not apply to: 1 damage in transit; 2.misuse or abuse(inc1udmgthe use of
incompatible or corrosive chemicals or overloading of capacity); 3 failure due to lack of proper
maintenance and care (including cleaning); 4.any design alteranons performed by an
organization not authorized or specifled by Windsor; 5 battenes and chargers. 6. high pressure
washing. 7.electrical components exposed to moisture.
If difficulty develops during the warranty penod, contact the authorized Windsor Agent from
whom the product was purchased. Windsor, Inc. may elect to require the return of components
to validate a claim. Any defective part to be returned must be shipped freight pre-paid to an
authonzed Windsor DistributorEerviceCenter or to the Windsor factory.
USE OF PARTS NOT APPROVED BY WINDSOR, INC.
WILL VOID ALL WARRANTIES.
This warranty is valid only for all products sold after July 1, 1995 A product sold before that
date shall be covered by the limited Warranty in effect at the date of sale to the onginal
purchaser.
I
m
m
w
WINWOR INDUSTRIES, INC., 1351 W. StanNwd Avo., Englauood, CO 80110 USA
Pkono: 303-762-1800 Fax: 303-762-0817 Internet: www.wlndeowind.com
$
c
1999 Windsor Indusmes, Inc All nghrS resewed REVISED OY24M