Download ALLEN & HEATH Xone:3D Service manual
Transcript
SERVICE MANUAL Issue 2 Publication AP6389 Allen & Heath 1 XONE:3D Service Manual Limited One Year Warranty This product is warranted to be free from defects in materials or workmanship for period of one year from the date of purchase by the original owner. To ensure a high level of performance and reliability for which this equipment has been designed and manufactured, read this User Guide before operating. In the event of a failure, notify and return the defective unit to ALLEN & HEATH Limited or its authorised agent as soon as possible for repair under warranty subject to the following conditions Conditions Of Warranty The equipment has been installed and operated in accordance with the instructions in this User Guide. The equipment has not been subject to misuse either intended or accidental, neglect, or alteration other than as described in the User Guide or Service Manual, or approved by ALLEN & HEATH. Any necessary adjustment, alteration or repair has been carried out by ALLEN & HEATH or its authorised agent. This warranty does not cover fader wear and tear. The defective unit is to be returned carriage prepaid to ALLEN & HEATH or its authorised agent with proof of purchase. Units returned should be packed to avoid transit damage. In certain territories the terms may vary. Check with your ALLEN & HEATH agent for any additional warranty which may apply. This product complies with the European Electro magnetic Compatibility directives 89/336/EEC & 92/31/EEC and the European Low Voltage Directives 73/23/EEC & 93/68/EEC. This product has been tested to EN55103 Parts 1 & 2 1996 for use in Environments E1, E2, E3, and E4 to demonstrate compliance with the protection requirements in the European EMC directive 89/336/EEC. During some tests the specified performance figures of the product were affected. This is considered permissible and the product has been passed as acceptable for its intended use. Allen & Heath has a strict policy of ensuring all products are tested to the latest safety and EMC standards. Customers requiring more information about EMC and safety issues can contact Allen & Heath. XONE:3D Service Manual AP6389 Issue 1 Copyright © 2006 Allen & Heath Limited. All rights reserved Allen & Heath Limited Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU, UK http://www.allen-heath.com http://www.xone.co.uk Allen & Heath 2 XONE:3D Service Manual Allen & Heath 3 XONE:3D Service Manual CAUTION INPUT 4 PHONO L INPUT 3 R PHONO L INPUT 2 R PHONO L INPUT 1 R LINE A L R FX1 R LINE B L R FX2 WARNING: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE WITH SAME TYPE AND RATING. ATTENTION: REMPLACER LE FUSIBLE AVEC UN DES MEMES CARACTERISTIQUES. LINE WARNING: THIS APPARATUS MUST BE EARTHED. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE APPARATUS TO RAIN OR MOISTURE. R LINE L R LINE L L GAME/MIDI R AC MAINS IN ~ OFF ON 0 I L FX RETURNS L R T500mAL 250V 20mm MIX OUT LEFT MONITOR RIGHT FX1 SEND L L SPDIF SOUNDCARD OUTPUTS FX2 SEND L CH1 L CH3 L CH5 L R CH2 R CH4 R CH6 R FUSE IN FOOT SWITCH DIGITAL AUDIO R R IN OPTICAL OUT SERIAL No: MIDI IN USB OUT TO PC OUT 100 - 240V~ 47-63Hz ~ 30W MAX MADE IN THE UK BY ALLEN & HEATH LIMITED ALLEN&HEATH BPM +10! +6 +3 MODE MIDI CH 0 MIDI -3 START STOP FX1 RESET FX1 FX1 -10 00 +6 CLOCK 00 +6 PRE + PULL FX1 -6 00 +6 PRE 00 +6 PRE -15 PRE -20 PUSH L TAP FX2 FX2 FX2 R FX2 5 4 6 3 +6 00 AUTO BPM SELECT FX2 MIX LINE A LINE B 9 0 5 0 PHONO LINE SC 5 - 6 LEVEL +10 +10 -10 HF +10 -10 HF MONITOR HF CUE ACTIVE +6 +6 OFF MF +6 OFF F G MF FX 2 J K +6 OFF LF 1 DEPTH 2 ASSIGN XFADE H L +6 +6 OFF OFF +6 OFF +6 PHONES LF LF LF 10 +6 OFF 1X RES +6 OFF FILTER XFADE 1X Y2 Y2 1X Y2 1X ADD MIX 5 6 9 10 1 0 CUE MILD HPF BPF LPF LEVEL Q R S T U V W X WILD HPF +10! +10! +10! +10! +6 +6 +6 +6 +3 +3 +3 +3 0 0 0 0 -3 -3 -3 -3 -6 -6 -6 -6 -10 -10 -10 -10 -15 -15 -15 -15 -20 -20 -20 -20 JOG / SELECT BPF LPF FREQ FREQ OO 20Hz P 4 WILD JOG / SELECT O 11 RES 3 N 8 2 Y2 M 7 3 OFF CUE 2 CUE 4 FILTER XFADE OFF CUE 1 MILD FILTER XFADE OFF CUE +6 OFF FILTER XFADE OFF ON I FX 1 +6 OFF MF MF OFF 7 8 1+2 E 8 9 10 9 0 D 7 0 +10 6 3 2 1 C 6 3 TAP TEMPO B 5 4 LEVEL FX2 RTN LFO A 10 SC 1 - 2 LEVEL -10 HF 6 10 5 9 0 1 OFF 4 8 1 2 -10 7 8 9 7 2 FX1 RTN 10 3 2 1 +6 00 PHONO LINE SC 3 - 4 LEVEL 6 7 8 4 PHONO LINE SC 1 - 2 5 3 2 1 +6 00 MIX OFF 4 +6 00 OO OO OO 20Hz 20kHz XFADE CURVE X 20kHz Y FILTER 1 ON FILTER 2 ON LF -12 PHONES Allen & Heath 5 HF +12 -12 LEVEL +12 0 10 MIC XONE:3D Service Manual EARTHING The connection to earth (ground) in an audio system is important for two reasons: SAFETY - To protect the operator from high voltage electric shock, and AUDIO PERFORMANCE - To minimise the effect of earth (ground) loops which result in audible hum and buzz, and to shield the audio signals from interference. For safety it is important that all equipment earths are connected to mains earth so that exposed metal parts are prevented from carrying high voltage which can injure or even kill the operator. It is recommended that a qualified system engineer check the continuity of the safety earth from all points in the system including microphone bodies, turntable chassis, equipment cases, and so on. The same earth is also used to shield audio cables from external interference such as the hum fields associated with power transformers, lighting dimmer buzz, and computer radiation. Problems arise when the signal sees more than one path to mains earth. An ‘earth loop’ (ground loop) results causing current to flow between the different earth paths. This condition is usually detected as a mains frequency audible hum or buzz. To ensure safe and trouble-free operation we recommend the following: Have your mains system checked by a qualified electrician. If the supply earthing is solid to start with you are less likely to experience problems. Do not remove the earth connection from the console mains plug. The console chassis is connected to mains earth through the power cable to ensure your safety. Audio 0V is connected to the console chassis internally. If problems are encountered with earth loops operate the audio ‘ground lift’ switches on connected equipment accordingly, or disconnect the cable screens at one end, usually at the destination. Make sure that turntables are correctly earthed. A chassis earth terminal is provided on the console rear panel to connect to turntable earth straps. Use low impedance sources such as microphones and line level equipment rated at 200 ohms or less to reduce susceptibility to interference. The console outputs are designed to operate at very low impedance to minimise interference problems. Use balanced connections for microphones and mix output as these provide further immunity by cancelling out interference that may be picked up on long cable runs. To connect an unbalanced source to a balanced console input, link the cold input (XLR pin 3 or jack ring) to 0V earth (XLR pin 1 or jack sleeve) at the console. To connect a balanced XLR output to unbalanced equipment, link the cold output to 0V earth at the console. Use good quality cables and connectors and check for correct wiring and reliable solder joints. Allow sufficient cable loop to prevent damage through stretching. If you are not sure ... Contact your service agent or local Allen & Heath dealer for advice. Allen & Heath 7 XONE:3D Service Manual MIXER TROUBLESHOOTING If things don’t seem to be working properly the first thing is not to panic. It is very easy to overlook a simple error or obvious problem in the heat of the moment. Instead, work methodically through a few checks before deciding there is an actual problem. Does the mixer power up NO Check the mains power socket with another appliance. If this works try another IEC lead on the mixer. If it still doesn’t work then check the fuse on the back of the unit. If it is blown only replace it with an identical type: T500mA If the Fuse blows again, or the unit is still dead, contact your service agent YES Are the CUE and Filter switches working? NO YES Front panel control processor not working. Reboot the mixer and if still does not work contact your service agent NO Check the channel input selection is correct for each audio source, that the player is working and that the interconnected leads are plugged into the correct channel input. NO BPM processor not working. Try rebooting the mixer and if it still does not work contact your service agent Is there audio on the channels as shown by the meters? YES/NO With the channel fader raised is there a signal on the main left/right monitor meters? See Following pages for more information on interfacing the Xone:3D to a computer YES Check FX1/2 monitor switches are up, that no channel cues are selected and that the crossfader is off Allen & Heath YES Does the Xone:3D Utility register that the unit is connected? See page 11 YES NO Is the BPM display working? Press Tap Tempo to confirm 8 Check that the Mix and monitor level controls are raised, that any connected amps are switched on with their level controls raised, the interconnects between the mixer and the amps and between the amps and the speaker system XONE:3D Service Manual Allen & Heath 9 XONE:3D Service Manual Allen & Heath 10 XONE:3D Service Manual PACKED ITEMS AP6388 USER GUIDE XONE:3D Mains Lead AH0205 AH0323 *MAINS LEAD IEC-2PIN EURO *MAINS LEAD IEC-3PIN C33 USA AH0206 *MAINS LEAD IEC-3PIN UK 10AMP AH6443 Type A-B USB Lead AP6442 Xone:3D Utility CD including: ASIO drivers, Configuration Utility software, Ableton Live Lite 6 application. Software Overlay Sheets For Serial numbers starting X3D: 003-536 Replacement KitAN6441 Ableton Live AN6442 Native Instruments Tractor AA6553-L & AA6553-R Rack Ears. AB5680 M4x10mm screws For Serial numbers starting X23D: 003-704 Replacement KitAN6880 Ableton Live AN6881 Native Instruments Tractor AL6531 Optical in/out blank plugs Allen & Heath 4 XONE:3D Service Manual SCREW TORX-Pt No.AB3820 BPM SCREW POZI-Pt No. AB3819 7 SEG DISPLAY-Pt No.003-524 MIDI CH MODE MIDI KNOB-Pt No. AJ6379 ENCODER-Pt No. AL6338 BUTTON-Pt No. AJ5325 LIGHT RING Pt No AJ5324 SWITCH-Pt No. AL0374 KNOB-Pt No. AJ5386 POT-Pt No. AI8004 START STOP RESET SWITCH-PtNo. AL6482 CLOCK + PULL PUSH TAP AUTO BPM SELECT FX2 MIX SWITCH-PtNo. AL5328 OFF 4 6 3 2 1 KNOB-Pt No.AJ5386 POT-Pt No.AI8007 KNOB-Pt No. AJ4310 FADER-PT No. AI4999 SCREW-Pt No.AB3818 FADER ASSY Pt No. 003-532 5 0 4 5 0 C TAP TEMPO 4 D E F G H 5 I J K L 10 DEPTH 2 ASSIGN XFADE SWITCH-Pt No. AL5328 1X ON RES KNOB-Pt No. AJ5387 POT Pt No. AI8007 KNOB-Pt No. AJ6379 ENCODER-Pt No. AL6338 JOG / SELECT 1+2 KNOB-Pt No.AJ5386 POT-Pt No. AI8007 KNOB-Pt No. AJ5386 POT-Pt No. AI8003 6 7 8 9 1 CAP-Pt No. AJ4251 SWITCH-Pt No. AL0374 FX2 RTN LFO 0 B 7 8 9 10 3 2 1 A FX1 RTN 6 3 2 1 BUTTON-Pt No. AJ5325 LIGHT RING Pt No AJ5324 SWITCH-Pt No. AL0374 7 8 9 10 MILD CUE CAP--Pt No. AJ3863 SWITCH-Pt No.AL0162 WILD HPF BUTTON-Pt No. AJ5325 LIGHT RING Pt No AJ5324 SWITCH-Pt No. AL0374 DECK ASSY-Pt No.AJ6342 +10! +6 +3 BPF 0 -3 -6 -10 LPF -15 -20 FREQ SCREW TORX-Pt No.AB3820 BUTTON-Pt No. AJ5325 LIGHT RING Pt No AJ5324 SWITCH-Pt No. AL0374 20Hz 20kHz KNOB-Pt No.AJ5387 POT Pt No. AI8004 NUT-Pt No. AB8172 XFADE CURVE FILTER 1 ON KNOB-Pt No. AJ5386 POT-Pt No. AI8004 ALLEN&HEATH +10! +6 CAP-Pt No. AJ5388 SWITCH-Pt No. AL0162 FX1 FX1 FX1 +3 0 -3 -6 FX1 -10 +6 00 +6 00 PRE +6 00 PRE FX2 +6 00 PRE FX2 KNOB-Pt No. AJ5386 POT-Pt No. AI8004 PRE FX2 -15 -20 L R FX2 5 4 6 3 00 +6 00 +6 LINE A LINE B 00 +6 PHONO LINE SC 1 - 2 +6 PHONO LINE SC 3 - 4 LEVEL 00 CAP-Pt No. AJ4251 SWITCH-Pt No. AL0333 PHONO LINE SC 5 - 6 SC 1 - 2 LEVEL LEVEL 7 2 KNOB-Pt No.AJ5386 POT-Pt No. AI8007 LEVEL PHONO LINE 8 1 9 0 10 MIX SC 1 - 2 5 4 6 3 7 2 -10 +10 -10 HF +10 -10 HF +6 OFF +6 +6 LF +6 +6 +6 LF +6 OFF OFF +6 OFF +6 PHONES CUE ACTIVE CAP-Pt No. AJ4251 SWITCH-Pt No. AL0162 KNOB-Pt No. AJ5387 POT-Pt No. AI8006 +6 FX 1 FX 2 PHONES LF OFF KNOB-Pt No. AJ5386 POT-Pt No. AI8003 CUE ADD MIX 5 4 FILTER XFADE 1X FILTER XFADE 1X Y2 OFF FILTER XFADE Y2 1X OFF CUE FILTER XFADE Y2 OFF CUE 4 +10! +10! +10! +6 +6 +6 +6 +3 +3 +3 +3 0 0 0 0 -3 -3 -3 -3 -6 -6 -6 -6 -10 -10 -10 -10 -15 -15 -15 -15 -20 -20 -20 -20 OO RES 3 +10! OO OO SWITCH-Pt No. AL5328 Y2 CUE 2 6 7 3 8 2 KNOB-Pt No. AJ5386 POT-Pt No. AI8007 OFF CUE 1 1X 10 MONITOR +6 OFF 8 9 0 MF OFF LF OFF +6 MF OFF KNOB-Pt No. AJ5386 POT-Pt No. AI8006 +10 HF OFF MF OFF -10 HF OFF MF +10 1 BUTTON-Pt No. AJ5325 LIGHT RING Pt No AJ5324 SWITCH-Pt No. AL0374 KNOB-Pt No. AJ5387 POT-Pt No. AI8007 SCREW POZI-Pt No. AB3819 KNOB-Pt No.AJ5320 FADER ASSY-Pt No.003-526 FADER-Pt No. AI6343 9 10 1 0 RES MILD BPF BUTTON-Pt No. AJ5325 LIGHT RING Pt No AJ5324 SWITCH-Pt No. AL0374 LPF FREQ KNOB-Pt No. AJ5387 POT-Pt No. AI8004 OO XFADE CURVE Allen & Heath Y WILD HPF 20Hz X LEVEL 11 SCREW POZI-Pt No. AB3819 KNOB-Pt No. AJ5320 FILTER 2 ON FADER ASSY-Pt No.003-579 1 BUTTON-Pt No. AJ5325 LIGHT RING Pt No AJ5324 SWITCH-Pt No. AL0374 20kHz FILTER 2 ON XONE:3D Service Manual TERMINAL POST-PT No AL8106 RCA PHONO PLUG SHORTINGPt No. AL4396 D TYPE CONNECTORPt No. AL6351 QUAD RCA SOCET-Pt No. AL497 SCREW-Pt No. AB2771 CAUTION INPUT 4 PHONO L R INPUT 3 PHONO L INPUT 2 R PHONO L LINE 0 I OFF ON L R LINE L R LINE L INPUT 1 R LINE A L R FX1 R LINE B L R FX2 WARNING: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE WITH SAME TYPE AND RATING. ATTENTION: REMPLACER LE FUSIBLE AVEC UN DES MEMES CARACTERISTIQUES. WARNING: THIS APPARATUS MUST BE EARTHED. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE APPARATUS TO RAIN OR MOISTURE. JACK SOCKETPt No. AL0328 FX RETURNS L R L GAME/MIDI R AC MAINS IN ~ T500mAL 250V 20mm LEFT MIX OUT RIGHT MONITOR L FX1 SEND L SPDIF SOUNDCARD OUTPUTS FX2 SEND L CH1 L CH3 L CH5 L R CH2 R CH4 R CH6 R FUSE IN FOOT SWITCH DIGITAL AUDIO OPTICAL OUT R R SERIAL No: IN MIDI IN OUT USB TO PC OUT 100 - 240V~ 47-63Hz ~ 30W MAX MADE IN THE UK BY ALLEN & HEATH LIMITED SWITCH CAP-Pt No AJ2887 PHONO DUAL SOCKET-Pt No. AL0566 XLR MALE SKT-Pt No. AL2411 SCREW-Pt No. AB2810 RCA DUAL VERTICAL SOCKETPt No.AL3753 SCREW -Pt No.AB2771 FUSE 20mm 500 mAPt No. AL3534 5 WAY DINPt No. AL0095 OPTICAL IN SOCKETUSB SOCKETPt No. AE6096 Pt No. AL6096 OPTICAL OUT SOCKETPt No. AE5899 OPTICAL IN/OUT BLANKING PLUGPt No. AL6531 LF -12 HF +12 -12 PHONES JACK SOCKETPt No. AL5323 AL5904AL5904AL5904AL5904AL5904AL4606AL6407AL6592AL5485AL6098AL3817AL3817AH2228 0 10 KNOB-Pt No. AJ4346 POT-Pt No. AI8004 KNOB-Pt No. AJ4346 POT-Pt No. AI8003 XLR SOCKETPt No. AL2414 SCREW-Pt No. CONNECTING WIREFORMS USED IN CONSOLE to HEADPHONE ASSY 7 SEGMENT DISPLAY ANALOGUE SLAVE ASSY JOGWHEEL (L) ASSY JOGWHEEL (R) ASSY CONNECTOR ASSY MIDI SLAVE (L) ASSY MIDI CONTROL (R) ASSY ANALOGUE SLAVE ASSY GAMEPORT ASSY LINEAR FADER ASSY`S X FADER ASSY MIDI FADER ASSY`S Allen & Heath +12 MIC JACK SOCKETPt No. AL0328 From LEVEL MASTER ASSY USB CONTROL ASSY POWER SUPPLY ASSY MIDI SLAVE (L) ASSY MIDI SLAVE (R) ASSY MASTER ASSY USB CONTROL ASSY USB CONTROL ASSY USB CONTROL USB COTROL ASSY INPUT ASSY`S FILTER ASSY MIDI SLAVE ASSY`S 2 XONE:3D Service Manual MASTER ASSYPt No. 003-522 Control IP (MIDI controller strips) IP 1, 2, 3, & 5, 6, 7 X:3D 003-535 X2:3D 003636 INPUT ASSYPt No. 003521 FILTER ASSY– Pt No. 003-525 7 SEGMENT DISPLAY ASSYPt No. 003-695 Control IP (MIDI controller strips) IP 1, 2, 3, & 5, 6, 7 X:3D 003-535 X2:3D 003636 IP 4 & 8 both models 003-635 INPUT P ASSY CONTROL Pt No. 003-635 CONTROL INPUT P ASSY IP 4 & 8 both models Pt No. 003-635 003-635 MIDI SLAVE R ASSYPt No. 003-546 MIDI SLAVE L ASSYPt No. 003-523 MIDI FADER ASSYPt No. 003-532 (under midi slave assy) MIDI FADER ASSYPt No. 003-532 (under midi slave assy) ANALOGUE SLAVE ASSY_ Pt No. 003-519 JOGWHEEL ASSYPt No. 003-533 JOGWHEEL ASSYPt No. 003-533 CONTROL INPUT ASSY_ Pt No.. 003-636 LINEAR FADER ASSYPt No. 003-526 X FADER ASSYPt No. 003-579 CONTROL INPUT ASSY_ Pt No.. 003-636 GAMEPORT ASSYPt No. 003-531 CONNECTOR ASSYPt No. 003-527 POWER SUPPLY ASSYPt No. 003-233 USB CONTROL ASSYPt No. 003-528 HEADPHONE SOCKET ASSYPt No. 003-530 Allen & Heath 3 XONE:3D Service Manual