Download Directed Audio 1500X Owner`s manual

DXA
AMPLIFIERS
Owner’s Manual
DXA250.1 | DXA500.1
DXA1000.1 | DXA1500.1
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE DXA.1
Benutzerhandbuch | Deutsch
MONOVERSTÄRKER DER DXA.1-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE DXA.1
DXA.1-SERIES AMPLIFIERS
OWNER’S MANUAL
MODEL:
DXA250.1 | DXA500.1 | DXA1000.1 | DXA1500.1
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
PERFORMANCE
Model:
DXA250.1
DXA500.1
DXA1000.1
DXA1500.1
RMS Power [Watts]
@ 14.4V, 4Ω mono, ≤ 1% THD+N
@ 14.4V, 2Ω mono, ≤ 1% THD+N
125 x 1
250 x 1
250 x 1
500 x 1
500 x 1
1000 x 1
750 x 1
1500 x 1
Length [in, cm]
8-1/8, 21
8-1/8, 21
12-1/16, 31
14, 36
Specifications common to all models:
Height [in, cm]
2-3/8, 6
Width [in, cm]
7-3/16, 18
Frequency Response [Hz]
25–200
Signal-to-Noise Ratio [dB]
>95, A-weighted, re: rated power
Input Sensitivity
Low Level: 125mV–5V
High Level: 250mV–10V
Electronic Crossover
Variable Lo-pass 50Hz–200Hz, 12dB/octave
KickEQ™ Bass Boost
Variable 0–12dB @ 40Hz
Subsonic Filter
25Hz, 24dB/octave
Remote Bass
Yes (sold separately)
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifier. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
battery’s negative post and the vehicle chassis is recommended.
The DXA amplifier has dual input sensitivity differential RCA inputs which will receive either high or low level
signals from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs
to the stereo RCA input on the end panel of the amplifier using the KICKER KISL as shown (make sure you set
the DXA amplifier’s input level switch to “HI”). Alternatively, the signal can be delivered to the amplifier using the
low-level RCA outputs on the source unit. Set the input level switch on the end panel of the amplifier to “LO”.
Either input method will provide a low-level output signal at the RCA output, which effectively passes the audio
signal to another amplifier or component. Keep the audio signal cable away from factory wiring harnesses and
other power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
2
source unit
high-level speaker
outputs
KICKER KISL (optional)
to amplifier
core conductor
+
OR
–
to amplifier
shield
from source unit highlevel speaker outputs
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifier. If you
ever need to remove the amplifier from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the amplifier--just the opposite as when you installed it.
Model
External Fuse
Power/Ground Wire
KICKER Wiring Kit
(sold separately)
DXA250.1
1 x 40 Ampere
8 Gauge
PK8, ZCK84
DXA500.1
1 x 80 Ampere
4 Gauge
PK4, CK44, ZCK44
DXA1000.1
1 x 150 Ampere
4 Gauge
PKD1, PWB050
DXA1500.1
1 x 150 Ampere
4 Gauge
PKD1, PWB050
MONO OPERATION
minimum impedance of 2 ohms
woofer
≤18”
(45cm)
≤24”
(60cm)
external fuse
12V
battery
remote turn-on
(see page 5)
bare-metal
chassis ground
3
OPERATION
Automatic Turn-On Selection: The DXA series offers two automatic turn-on modes; +12V and DC Offset.
• Remote Turn-On: Run 18 gauge wire from the Remote Turn-On Lead on your source unit to the terminal
labeled REM between the amplifier’s positive and negative power terminals.
• DC Offset Turn-On: The DC Offset mode detects a 6V DC offset from the HI-Level speaker outputs when
the source unit has been turned on.
Input Level: The RCA inputs on KICKER DXA amplifiers are capable of receiving either Hi or Low-level signals
from your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the
Input Level switch on the amplifier. Refer to the wiring section of this manual for additional instructions.
Crossover Control: The variable crossover on the side of the amplifier allows you to adjust the lo-pass
crossover frequency from 50–200Hz. The setting for this control is subjective; 80Hz is a good place to start.
Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to
the input level of the amplifier. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it
to 25). Next, slowly turn (clockwise) the gain on the amplifier up until you can hear audible distortion, then turn it
down a little.
Bass Boost Control: The variable bass boost control on the side of the amplifier is designed to give you
increased output, 0–12dB, at 40Hz. The setting for this control is subjective. If you turn it up, you must readjust
the input gain control to avoid clipping the amplifier.
Remote Bass-CXRC (sold separately): With the optional CXRC remote bass level control, you have the
ability to control the output level of the amplifier remotely. To surface-mount the CXRC remote bass level control,
simply screw the remote to the chosen location, then run the cable from the controller to the “Remote Bass”
jack on the amplifier panel. Do NOT connect/disconnect while the amplifier is on. Connecting the 3.5mm cable
without the remote will cause the amplifier to output at full gain, possibly damaging your speakers. See page 6
for installation.
4
CXRC REMOTE BASS INSTALLATION
Surface-mount the CXRC remote
using the supplied screws.
back view
Remote cable passes audio; do not
run cable parallel to power wires.
Connect the supplied 1/8th inch [3.5mm] patch cable to the
CXRC remote and the Remote Bass jack on the amplifier
TROUBLESHOOTING
If your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or
incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There are Power (PWR)
& Protection (PRT) LEDs on the side panel of your Kicker DXA series amplifier. Depending on the state of the
amplifier and the vehicle’s charging system, the LEDs will glow either green or red. When the green LED is lit, this
indicates the amplifier is turned on and no trouble exists.
Green LED off, no output? With a Volt Ohm Meter (VOM) check the following: n+12 volt power terminal
(should read +12V to +16V) oRemote turn-on terminal (should read +12V to +16V) pCheck for reversed
power and ground connections qGround terminal, for proper conductivity.
Green LED on, no output? Check the following: nRCA connections oTest speaker outputs with a
“known” good speaker. pSubstitute source unit with a “known” good source unit. qCheck for a signal in the
RCA cable feeding the amplifier with the VOM meter set to measure “AC” voltage.
Red LED flickering with loud music? The red LED indicates low battery voltage. Check all the connections
in your vehicle’s charging system. It may be necessary to replace or charge your vehicle’s battery or replace your
vehicle’s alternator.
Red LED on, no output? nAmplifier is very hot = thermal protection is engaged. Test for proper impedance at
the speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance
and multiple speaker wiring suggestions). Also check for adequate airflow around the amplifier. oAmplifier
shuts down only while vehicle is running = voltage protection circuitry is engaged. Voltage to the amplifier is not
within the 10–16 volt operating range. Have the vehicle’s charging and electrical system inspected. pAmplifier
will only play at low volume levels = short circuit protection is engaged. Check for speaker wires shorted to
each other or to the vehicle chassis. Check for damaged speakers or speaker(s) operating below the minimum
recommended impedance.
No or low output? nCheck the balance control on source unit
speaker output connections.
oCheck the RCA (or speaker input) and
Alternator noise-whining sound with engine’s RPM? nCheck for damaged RCA (or speaker input) cable
oCheck the routing of RCA (or speaker input) cable pCheck the source unit for proper grounding qCheck
the gain settings and turn them down if they are set too high.
Ground Noise? KICKER amplifiers are engineered to be fully compatible with all manufacturers’ head units.
Some head units may require additional grounding to prevent noise from entering the audio signal. If you are
experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the
head unit to the chassis will remedy this issue.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct.
Improper connections can result in blown amplifier fuses as well as the failure of other critical systems in the
vehicle.
5
If you have more questions about the installation or operation of your new KICKER product, see the Authorized
KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on
the KICKER homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab, choose the subject you are
interested in, and then download or view the corresponding information. Please E-mail [email protected] or
call Technical Services (405) 624-8583 for unanswered or specific questions.
DXA250.1
125 x 1 @ 4 ohms, 14.4VDC, 1% THD, CEA-2006B (Watts)
Signal to Noise Ratio -75dB CEA-2006 (ref: 1W, A-weighted)
DXA500.1
250 x 1 @ 4 ohms, 14.4VDC, 1% THD, CEA-2006B (Watts)
Signal to Noise Ratio -75dB CEA-2006 (ref: 1W, A-weighted)
DXA1000.1
500 x 1 @ 4 ohm, 14.4VDC, 1% THD, CEA-2006B (Watts)
Signal to Noise Ratio -70dB CEA-2006 (ref: 1W, A-weighted)
DXA1500.1
750 x 1 @ 4 ohm, 14.4VDC, 1% THD, CEA-2006B (Watts)
Signal to Noise Ratio -70dB CEA-2006 (ref: 1W, A-weighted)
KICKER will now provide a threeyear warranty with all DXA-Series
Amplifier purchases paired with a
qualifying KICKER Installation Kit* .
This extends the standard warranty by an additional
year. Amplifier and Kit must be purchased from an
Authorized KICKER Dealer.
KICKER DXA amplifier success is currently at an unheard-of rate, making the
extended warranty program even more beneficial to you.
Using poor-quality, under-spec wiring kits will impede DXA amplifier performance.
A superior-quality KICKER installation Kit is guaranteed to extend the life of DXA
amplifiers.
The new extended warranty applies only to KICKER amplifiers and accessories sold to consumers by Authorized
KICKER Dealers in the United States of America or its possessions. It also only applies to the original purchaser of
KICKER amplifiers and accessories. One warranty extension per amplifier is allowed regardless of the number of amplifier
installation kits purchased. This program does not apply to “B”-stock product or factory-refurbished product.
This offer is for a limited time, so see your local Authorized KICKER Dealer soon for details.
*U.S.A. Only | EE.UU. solamente | Nur USA | Les USA Seulement
6
ELECTRONICS LIMITED WARRANTY
When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material
and workmanship under normal use for a period of TWO (2) YEARS from date of original purchase with receipt. If this
product is identified as “Refurbished” or “B Goods”, the warranty is limited to a period of THREE (3) MONTHS from
the date of original purchase. In all cases you must have the original receipt. Should service be necessary under this
warranty for any reason due to manufacturing defect or malfunction during the warranty period, KICKER will repair or
replace (at its discretion) the defective merchandise with equivalent merchandise. Warranty replacements may have
cosmetic scratches and blemishes. Discontinued products may be replaced with more current equivalent products. This
warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to the original
purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty as provided herein
beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this
product thereafter. Some states do not allow limitations on implied warranties; therefore, these exclusions may not apply
to you. This warranty gives you specific legal rights; however you may have other rights that vary from state to state.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE:
Defective merchandise should be returned to your local Authorized Stillwater Designs (KICKER) Dealer for warranty
service. Assistance in locating an Authorized Dealer can be found at www.kicker.com or by contacting Stillwater Designs
directly. You can confirm that a dealer is authorized by asking to see a current authorized dealer window decal.
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (KICKER), call the KICKER
Customer Service Department at (405) 624-8510 for a Return Merchandise Authorization (RMA) number. Package only
the defective items in a package that will prevent shipping damage, and return to:
Stillwater Designs, 3100 North Husband St, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Please return only defective components. The
return of functioning items increases your return freight charges. Non-defective items will be returned freightcollect to you.
For example, if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure. Include a copy
of the original receipt with the purchase date clearly visible, and a “proof-of-purchase” statement listing the Customer’s
name, Dealer’s name and invoice number, and product purchased. Warranty expiration on items without proof-ofpurchase will be determined from the type of sale and manufacturing date code. Freight must be prepaid; items sent
freight-collect, or COD, will be refused.
WHAT IS NOT COVERED?
This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover:
o Damage due to improper installation
o Subsequent damage to other components
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be
considered abuse
o Any cost or expense related to the removal or reinstallation of product
o Speakers damaged due to amplifier clipping or distortion
o Items previously repaired or modified by any unauthorized repair facility
o Return shipping on non-defective items
o Products with tampered or missing barcode labels
o Products with tampered or missing serial numbers
o Products returned without a Return Merchandise Authorization (RMA) number
o Products purchased from an UNAUTHORIZED dealer
o Freight Damage
o The cost of shipping product to KICKER
o Service performed by anyone other than KICKER
stillwaterdesigns
HOW LONG WILL IT TAKE?
KICKER strives to maintain a goal of one week turnaround for all electronics (amplifiers, crossovers, equalizers, etc.)
returns. Delays may be incurred if lack of replacement inventory or parts is encountered. Failure to follow these steps
may void your warranty. Any questions can be directed to the KICKER Customer Service Department at (405) 624-8510.
Contact your International KICKER dealer or distributor concerning specific procedures for your country’s warranty
policies.
Note: All specifications and performance figures are subject to change. Please visit www.kicker.com for the most
current information.
P.O. Box 459 • Stillwater, Oklahoma 74076 • USA • (405) 624–8510
22
14DXA.1HI-B-20130802
INTERNATIONAL WARRANTY
Contact your International KICKER dealer or distributor concerning
specific procedures for your country’s warranty policies.
WARNING: KICKER products are capable of producing sound levels
that can permanently damage your hearing! Turning up a system to a
level that has audible distortion is more damaging to your ears than
listening to an undistorted system at the same volume level. The
threshold of pain is always an indicator that the sound level is too loud
and may permanently damage your hearing. Please use common
sense when controlling volume.
GARANTÍA INTERNACIONAL
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a
major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Versión Español
Comuníquese con su concesionario o distribuidor KICKER internacional para obtener infor ación sobre procedimientos específicos
relacionados con las normas de garantía de su país.
ADVERTENCIA: Los excitadores KICKER son capaces de producir niveles de sonido que pueden dañar permanentemente
el oído. Subir el volumen del sistema hasta un nivel que produzca distorsión es más dañino para el oído que escuchar un
sistema sin distorsión al mismo volumen. El dolor es siempre una indicación de que el sonido es muy fuerte y que puede dañar
permanentemente el oído. Sea precavido cuando controle el volumen.
La frase “combustible para vivir la vida Livin’ Loud™ a todo volumen” se refiere al entusiasmo por la vida que la marca KICKER
de estéreos de automóvil representa y a la recomendación a nuestros clientes de que vivan lo mejor posible (“a todo volumen”)
en todo sentido. La línea de altavoces y amplificadores KICKER es la mejor del mercado de audio de automóviles y por lo tanto
representa el “combustible” para vivir a todo volumen en el área de “estéreos de automóvil” de la vida de nuestros clientes.
Recomendamos a todos nuestros clientes que obedezcan todas las reglas y reglamentos locales sobre ruido en cuanto a los
niveles legales y apropiados de audición fuera del vehículo.
INTERNATIONALE GARANTIE
Deutsche Version
Nehmen Sie mit Ihren internationalen KICKER-Fachhändler oder Vertrieb Kontakt auf, um Details über die Garantieleistungen in
Ihrem Land zu erfahren.
WARNUNG: KICKER-Treiber können einen Schallpegel erzeugen, der zu permanenten Gehörschäden führen kann! Wenn Sie ein
System auf einen Pegel stellen, der hörbare Verzerrungen erzeugt, schadet das Ihren Ohren mehr, als ein nicht verzerrtes System
auf dem gleichen Lautstärkepegel. Die Schmerzschwelle ist immer eine Anzeige dafür, dass der Schallpegel zu laut ist und zu
permanenten Gehörschäden führen kann. Seien Sie bei der Lautstärkeeinstellung bitte vernünftig!
Der Slogan “Treibstoff für Livin’ Loud” bezieht sich auf die mit den KICKER-Autostereosystemen assoziierte Lebensfreude und die
Tatsache, dass wir unsere Kunden ermutigen, in allen Aspekten ihres Lebens nach dem Besten (“Livin’ Loud”) zu streben. Die
Lautsprecher und Verstärker von KICKER sind auf dem Markt für Auto-Soundsysteme führend und stellen somit den “Treibstoff”
für das Autostereoerlebnis unserer Kunden dar. Wir empfehlen allen unseren Kunden, sich bezüglich der zugelassenen und
passenden Lautstärkepegel außerhalb des Autos an die örtlichen Lärmvorschriften zu halten.
GARANTIE INTERNATIONALE
Version Française
Pour connaître les procédures propres à la politique de garantie de votre pays, contactez votre revendeur ou distributeur
International KICKER.
AVERTISSEMENT: Les haut-parleurs KICKER ont la capacité de produire des niveaux sonores pouvant endommager l’ouïe de
façon irréversible ! L’augmentation du volume d’un système jusqu’à un niveau présentant une distorsion audible endommage
davantage l’ouïe que l’écoute d’un système sans distorsion au même volume. Le seuil de la douleur est toujours le signe que le
niveau sonore est trop élevé et risque d’endommager l’ouïe de façon irréversible. Réglez le volume en faisant prevue de bon sens!
L’expression “ carburant pour vivre plein pot “ fait référence au dynamisme de la marque KICKER d’équipements audio pour
véhicules et a pour but d’encourager nos clients à faire le maximum (“ vivre plein pot “) dans tous les aspects de leur vie. Les
haut-parleurs et amplificateurs KICKER sont les meilleurs dans le domaine des équipements audio et représentent donc pour nos
client le “ carburant pour vivre plein pot “ dans l’aspect “ installation audio de véhicule “ de leur vie. Nous encourageons tous nos
clients à respecter toutes les lois et réglementations locales relatives aux niveaux sonores acceptables à l’extérieur des véhicules.
23
©2013 Stillwater Designs