Download Allen-Bradley 1738-ADNX User manual

Allen-Bradley I/O
Modules
1732, 1734, 1734D, 1738, 1746,
1747, 1756, 1761, 1762, 1764,
1769, 1771, 1790, 1791, 1791D,
1791P, 1791R, 1792D, 1794,
1797, 1798, 1799
Wiring Diagrams
Important User Information
Solid state equipment has operational characteristics differing from those of
electromechanical equipment. Safety Guidelines for the Application, Installation and
Maintenance of Solid State Controls (Publication SGI-1.1 available from your local
Rockwell Automation sales office or online at
http://www.literature.rockwellautomation.com) describes some important differences
between solid state equipment and hard-wired electromechanical devices. Because of
this difference, and also because of the wide variety of uses for solid state equipment,
all persons responsible for applying this equipment must satisfy themselves that each
intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or
consequential damages resulting from the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes.
Because of the many variables and requirements associated with any particular
installation, Rockwell Automation, Inc. cannot assume responsibility or liability for
actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of
information, circuits, equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written
permission of Rockwell Automation, Inc. is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of
safety considerations.
WARNING
IMPORTANT
ATTENTION
Identifies information about practices or circumstances
that can cause an explosion in a hazardous environment,
which may lead to personal injury or death, property
damage, or economic loss.
Identifies information that is critical for successful
application and understanding of the product.
Identifies information about practices or circumstances that can
lead to personal injury or death, property damage, or economic
loss. Attentions help you identify a hazard, avoid a hazard and
recognize the consequences.
SHOCK HAZARD
Labels may be located on or inside the drive to alert
people that dangerous voltage may be present.
BURN HAZARD
Labels may be located on or inside the drive to alert
people that surfaces may be dangerous temperatures.
Preface
Introduction
The purpose for showing these connection diagrams here is to
illustrate the following attributes of each I/O module, I/O block, or
fixed I/O controller:
• the number of inputs and/or outputs
• whether there is a single common for all I/O, a common for a
set of I/O separate from other sets of I/O, or a signal return for
each I/O circuit so that each I/O circuit is isolated from all
others
• whether an output is a current source or a current sink
• whether an input is a source load or a sink load
To fit them into this concise format, these diagrams are intentionally
simplified to the point that they do not show the type of cables,
twisted pairs, cable shields or the grounding of cable shields. We
make an exception where the cable shield must be connected at an
I/O terminal.
For those input modules or blocks that can tolerate the leakage
current of proximity sensors, we usually show a proximity sensor at
one input and hard contacts at the others for ease of illustration.
IMPORTANT
Many of the catalog numbers included in this
publication have specific wiring guidelines and
recommendations that are listed in the product’s
technical documentation (e.g. installation instructions
or user manuals) but not here because the purpose
of this publication is to show connection diagrams
and basic information required to wire each I/O
module.
For a full description of how to use each of the
catalog numbers listed in this publication, see the
individual product’s technical documentation.
1
Publication CIG-WD001B-EN-P - May 2005
Preface
2
Abbreviations
Symbols
In these diagrams we used the following abbreviations:
no
normally open (contact outputs)
nc
normally closed (contact outputs)
n.c.
no connection (do not connect to this terminal)
In these diagrams we used the following symbols:
ac power source
ac/dc power source
+
dc power source
output load
current-signal analog sensor
voltage-signal analog sensor
RTD
thermocouple
3-wire proximity sensor
4-wire proximity sensor
+
+
Prox
hard-contact switching devices
TTL switching device
Publication CIG-WD001B-EN-P - May 2005
or
+
TTL
Table of Contents
Chapter 1
1732 ArmorBlock I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Chapter 2
1734 POINT I/O Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Chapter 3
1734D POINTBlock I/O Modules . . . . . . . . . . . . . . . . . . . . . . . 3-1
Chapter 4
1738 ArmorPoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Chapter 5
1746 I/O Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Chapter 6
1747 I/O on Fixed Hardware Controllers . . . . . . . . . . . . . . . . . . 6-1
Chapter 7
1756 ControlLogix I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Chapter 8
1761 Controller I/O on MicroLogix 1000 Controllers . . . . . . . . 8-1
Chapter 9
1762 I/O on MicroLogix 1200 Controllers . . . . . . . . . . . . . . . . . 9-1
Chapter 10
1764 Controller I/O on MicroLogix 1500 Controllers . . . . . . . 10-1
Chapter 11
1769 Compact I/O Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
Chapter 12
1771 I/O Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
Chapter 13
1790 CompactBlock LDX I/O Modules . . . . . . . . . . . . . . . . . . 13-1
Chapter 14
1791 I/O Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
1
Publication CIG-WD001B-EN-P - May 2005
Table of Contents
2
Chapter 15
1791D CompactBlock I/O Blocks . . . . . . . . . . . . . . . . . . . . . . . 15-1
Chapter 16
1791P CompactBlock I/O Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1
Chapter 17
1791R CompactBlock I/O Blocks . . . . . . . . . . . . . . . . . . . . . . . 17-1
Chapter 18
1792D ArmorBlock MaXum I/O Blocks . . . . . . . . . . . . . . . . . 18-1
Chapter 19
1794 FLEX I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-1
Chapter 20
1797 FLEX Ex Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-1
Chapter 21
1798 FLEX Armor I/O Modules . . . . . . . . . . . . . . . . . . . . . . . . 21-1
Chapter 22
1799 Embedded I/O Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-1
Publication CIG-WD001B-EN-P - May 2005
Chapter
1
1732 ArmorBlock I/O
1732D-8CFGM12
1732D-8CFGM8
Self-configuring Connector
(view into connector)
Self-configuring Connector
(view into connector)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Sensor Source Voltage
Input or Output B
Return
Input or Output A
Not Used
1732D-IB8M12
Pin 1 Sensor Source Voltage
Pin 3 Return
Pin 4 Input or Output
1732D-IB8M8
Input Micro-Connector
(view into connector)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Sensor Source Voltage
Input B
Return
Input A
Not used
1732D-OB8EM12
Input Pico-Connector
(view into connector)
Pin 1 Sensor Source Voltage
Pin 3 Return
Pin 4 Input
1732D-OB8EM8
Output Micro-Connector
(view into connector)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
1
Not Used
Output B
Return
Output A
Not Used
Output Pico-Connector
(view into connector)
Pin 1 Not Used
Pin 3 Return
Pin 4 Output
Publication CIG-WD001B-EN-P - May 2005
1-2
1732 ArmorBlock I/O
1732P-8CFGM12
1732P-8CFGM8
Self-configuring Connector
(view into connector)
Self-configuring Connector
(view into connector)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Sensor Source Voltage
Input or Output B
Return
Input or Output A
Not Used
1732P-IB8M12
Pin 1 Sensor Source Voltage
Pin 3 Return
Pin 4 Input or Output
1732P-IB8M8
Input Micro-Connector
(view into connector)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Sensor Source Voltage
Input B
Return
Input A
Not used
1732P-OB8EM12
Input Pico-Connector
(view into connector)
Pin 1 Sensor Source Voltage
Pin 3 Return
Pin 4 Input
1732P-OB8EM8
Output Micro-Connector
(view into connector)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Publication CIG-WD001B-EN-P - May 2005
Not Used
Output B
Return
Output A
Not Used
Output Pico-Connector
(view into connector)
Pin 1 Not Used
Pin 3 Return
Pin 4 Output
Chapter
2
1734 POINT I/O Modules
1734-232ASC
Tx
S+
Rx
2
NC
7
NC
NC
4
5
NC
3
S-
NC
4
NC
2
3
NC
1
0
1
0
6
1734-485ASC
6
SG
Tx = Transmit
NC = No Connection
5
Rx = Receive
SG = Signal Ground
0
Tx, S+ = Transmit
NC = No Connection
CG = Chassis Ground
NC
2
Do not connect 120/240V ac
power to this supply.
Chas Chas
Gnd Gnd
4
V dc
3
5
C
C
V
V
6
7
This dc supply will be
connected to the
internal power bus.
Rx, S- = Receive
SG = Signal Ground
0
Do not connect
120/240V ac
power to this
supply.
1
NC
Chas Gnd = Chassis Ground
V = Supply
NC
2
3
Chas Chas
Gnd Gnd
4
5
C
V dc
C
6
7
V
NC = No Connection
C = Common
SG
1734-EP24DC
12/24V dc
1
NC
7
CG
1734-ADN, -ADNX, -ACNR, -AENT, -APB
12/24V dc
Power
NC
NC
V
This dc supply will be
connected to the
internal power bus.
V = 12/24V dc, C = Common
CHAS GND = Chassis ground
1
Publication CIG-WD001B-EN-P - May 2005
2-2
1734 POINT I/O Modules
1734-FPD (12/24V dc)
0
1
NC
2
0
NC
Chas Chas
Gnd Gnd
4
3
Chas Chas
Gnd Gnd
This dc supply will be
connected to the
internal power bus.
4
7
V
NC
2
3
C
6
1
NC
5
C
V dc
1734-FPD (120/240V ac)
5
L2/N
L2/N
L1
L1
6
V ac
7
V
NC = No Connection Chas Gnd = Chassis Ground
C = Common
V = 12/24V dc
NC = No Connection Chas Gnd = Chassis Ground
L1 = 120/240V ac
L2/N = ac Neutral
1734-IA2
1734-IB2
0
2
Prox
Ch 1
NC
NC
L2/N
L2/N
1
2
3
Prox
Prox
4
0
Sink Input
1
Ch 0
2-Wire
NC
NC
C
C
7
7
V
2-Wire
Prox
3-Wire
Prox
2
1734-IB8
3-wire
1
In 0
In 2
In 1
In 3
4
3
5
C
3-wire
Prox
1
In 0
Prox
Prox
3-wire
Prox
V
2-wire
Prox
V = 12/24V dc, C = Common
12/24V dc is supplied through the internal power bus
V
C
Prox
In 1
2-wire
7
V
3-wire
0
Prox
2-wire
C
6
V
V = 12/24V dc, C = Common
12/24V dc is supplied through the internal power bus
Ch 1 = Channel 1
L2/N = 120V ac Neutral
0
Prox
3-Wire
6
1734-IB4
Sink Input
3
5
L1
Ch 0 = Channel 0
NC = No Connection
L1 = 120V ac
In 1
2-Wire
3-Wire
L1
In 0
4
5
6
This ac supply will be
connected to the
internal power bus.
2-wire
2
3
In 2
In 3
4
Prox
3-wire
5
In 4
In 5
In 6
In 7
Prox
2-wire
6
7
Prox
C
V = 12/24V dc
C = Common
Daisy chain common and power connections from 1734 Adapter, 1734-FPD,
1734-EP24DC or from user supplied external auxiliary terminal block.
Publication CIG-WD001B-EN-P - May 2005
V
1734 POINT I/O Modules
1734-IE2C
0
In 0
2
4
6
In
0
In
1
1734-IE2V
Voltage
Input
1
In 1
0
Chas Chas 3
Gnd Gnd
C
V
2
0
0
1
Aret
B
Bret
Z
Zret
3
2
5
4
6
Chas 7
Gnd
Chas
Gnd
0
V
V
Aret
B
Bret
Z
Zret
3
5
Chas
Gnd
Chas 7
Gnd
1734-IR2
3
NC
0
Ch 1
2
NC
4
2
Prox
3-wire
RTD
5
L2/N
L2/N
L1
7
A, B, Z, Aret, Bret, and Zret = inputs
Chas Gnd = Chassis Ground
1
Ch 0
Ch 0 = Channel 0 input
NC = No connection
L1 = 220V ac
C
1
A
1734-IM2
L1
C
V = 12/24V dc, C = Common
12/24V dc is supplied from the internal power bus
A, B, Z, Aret, Bret, and Zret = inputs
Chas Gnd = Chassis Ground
6
3
1734-IK
A
4
2-wire
Voltage
Input
5
6
1734-IJ
Prox
Chas Chas
Gnd Gnd
1
7
V = 12/24V dc, C = Common
12/24V dc is supplied from the internal power bus
6
In
1
4
V
2
In
0
5
C
2-3
3-wire
7
4
In
In
0/A 1A
In In
0/B 1/B
1
3
5
RET 0 RET 1
6
2-wire
RTD
7
Shield Shield
In = Input Channel
RET = Sensor Return
Shield = Sensor Cable Shield
When using 2-wire RTDs,
jumper In/B to RET.
Ch 1 = channel 1 input
L2/N = 220V ac Neutral
Publication CIG-WD001B-EN-P - May 2005
2-4
1734 POINT I/O Modules
1734-IT2I
1734-IV2
Source Input
0
1
In 0
In 1
NC
NC
C
C
V
V
3
Shield
4
0+ = Input Channel 0 High
0- = Input Channel 0 Low
1+ = Input Channel 1 High
1- = Input Channel 1 Low
5
0+
4
2-Wire
7
1+
1-
5
6
V = 12/24V dc, C = Common
12/24V dc is supplied through the internal power bus
3-Wire
Prox
2-Wire
Prox
2
1734-IV8
3-wire
1
In 0
In 2
In 1
In 3
4
3
5
C
1
In 0
3-Wire
Prox
Prox
Prox
3-wire
Prox
V
2-wire
Prox
V = 12/24V dc, C = Common
12/24V dc is supplied through the internal power bus
C
V
Prox
In 1
2-wire
7
V
3-wire
0
Prox
2-Wire
C
6
3-Wire
7
1734-IV4
0
Prox
Thermocouple 1
Use the 1734-TBCJC wiring base assembly for cold junction compensation.
Source Input
3
Thermocouple 0
0-
6
2
Prox
2-wire
3
2
In 2
In 3
Prox
3-wire
5
4
In 4
In 5
In 6
In 7
Prox
2-wire
6
7
Prox
V
V = 12/24V dc
C = Common
Daisy chain common and power connections from 1734 Adapter, 1734-FPD,
1734-EP24DC or from user supplied external auxiliary terminal block.
Publication CIG-WD001B-EN-P - May 2005
C
1734 POINT I/O Modules
1734-OA2
0
2
Load
1734-OB2
1
Ch 0
Ch 1
NC
NC
4
0
1
Out 0 Out 1
2
3
3
Out 0 Out 1
Load
Load
5
L2/N
4
L2/N
7
L1
L1
C
C
V
V
1734-OB2E, -OB2EP
1734-OB4
0 Out
Load
4
0
C
V
V
6
2
Load
Load
Load
4
6
V = 12/24V dc, C = Common
Field power is supplied from the internal power bus
Module power is supplied from the internal power bus
2
Load
Load
Out 1
1
Out
2
Out 3
3
4
5
C
C
C
C
Load
7
0
Load
Load
Load
1
Out 0
Out 1
Out 2
Out 3
Out 4
Out 5
2
Load
3
4
Load
7
C
C
1734-OB8
C
6
Load
5
V = 12/24V dc, C = Common
Field power is supplied from internal power bus
1734-OB4E
Out
0
3
Out 2 Out 3
7
0
1
Out 0 Out 1
5
C
7
V = 12/24V dc, C = Common
Field power is supplied from internal power bus
Ch 0 = Channel 0
Ch 1 = Channel 1
NC = No Connection L2/N = 120/220V ac Return
L1 = 120/220V ac Supply
Field power is supplied from the internal power bus.
Out 1
0 1
2 Out Out 3
0 1
Load
5
6
6
2-5
Load
Load
5
Load
C
42015
6
V = 12/24V dc, C = Common
Field power is supplied from the internal power bus
Module power is supplied from the internal power bus
Load
7
Out 6
Out 7
Load
C
C
Common must be daisy chained from a 1734 adapter, 1734-FPD, 1734-EP24DC,
or from a user-supplied auxiliary terminal block.
The 24V dc power to the module is supplied by the internal power bus and comes
from the same 1734 adapter, 1734-FPD, or 1734-EP24DC as common.
Publication CIG-WD001B-EN-P - May 2005
2-6
1734 POINT I/O Modules
1734-OB8E
1734-OE2C
0
Load
1
Out 0
Out 1
Out 2
Out 3
2
Load
Load
3
0
Current
Output
Device
ac or
dc
Load
2
4-wire
4
Load
5
Out 2
6
Load
Out = Output channel
Chas Gnd = Chassis ground
V = Not used
C = Common
7
Out 2
Load
Out 3
C
6
1
Out
1
C
C
V
V
Current
Output
Device
3
Chas Chas
Gnd Gnd
4
Load
Out 3
Out
0
2-wire
5
7
C
Common must be daisy chained from a 1734 adapter, 1734-FPD, 1734-EP24DC,
or from a user-supplied auxiliary terminal block.
The 24V dc power to the module is supplied by the internal power bus and comes
from the same 1734 adapter, 1734-FPD, or 1734-EP24DC as common.
1734-OE2V
Voltage
Output
0
Out
0
1734-OV2E
3
Chas Chas
Gnd Gnd
Out = Output channel
Chas Gnd = Chassis ground
C = Common
V = 12/24V Supply
6
C
V
Load
NC
NC
3
6
7
Load
5
C
C
V
V
7
V = 12/24V dc, C = Common
Field power is supplied from internal power bus
1734-OV4E
0
1734-OW2 Load Powered by External Power Bus
1
Out 0
Power
Supply
Out 1
2
3
Out 2
Load
Out 1
4
5
C
V
1
Out 0
2
2
4
Voltage
Output
1
Out
1
0
Out 3
Load
Load
4
7
V
Publication CIG-WD001B-EN-P - May 2005
Out 1
1A
2
Out
0B
Out 3
1B
C
C
V
V
4
V
6
V
V = 12/24V dc, C = Common
Field power is supplied from internal power bus
Out
0A
Load
5
V
0
Load
Power
Supply
5
6
7
Load
Out = Output channel relay contacts
V = Supply (can range from +5V dc to 240V ac)
C = Common
1734 POINT I/O Modules
1734-OW2 Load Powered by Internal Power Bus
0
2
Load
Out
0A
Out
1A
Out
0B
Out
1B
4
1
1734-OW4 Load Powered by External Power Bus
Load
Out 0A Out 1A
Load
3
Out 0B Out 1B
4
Power
Supply
C
Load
7
V
V
Load
5
Power
Supply
Out 2A Out 3A
6
6
Power
Supply
1
0
Power
Supply
2
3
5
C
2-7
7
Out 2B Out 3B
Load
Out = Output channel relay contacts
Out = Output channel relay contacts
V = Supply (can range from +5V dc to 240V ac)
C = Common
Supply voltage can range from +5V dc to 240V ac, depending on relay load.
12/24V dc power for the module is provided by the external power supply.
The power supply voltage may be daisy chained from a 1734 adapter, 1734-FPD
or 1734-EP24DC communication interface. Each channel is individually isolated
and may have a unique supply and/or voltage as necessary.
1734-OX2 Load Powered by External Power Bus
L1
Power
Supply
0
Out 0
NO
NC
Out 1
NO
4
Load
Out 0
RC
6
+V
Out 0
NC
Out 1
2
3
Power
Supply
L1
2
Load
L2/N
5
Out 1
RC
Load
L2/N
Out 0
NO
4 Out 0
L1
Out 1
NC
Out 1
NO
3
RC
Out 1 5
RC
+V
+V
6
7
+V
Out = Output channel relay contacts
Power Supply = can range from +5V dc to 240V ac
RC = Relay Common
1
0
1
Out 0
NC
L2/N
1734-OX2 Load Powered by Internal Power Bus
7
L2/N
Load
L1
NC = Normally closed
NO = Normally open
RC = Relay Common
+V = Positive Supply
Publication CIG-WD001B-EN-P - May 2005
2-8
1734 POINT I/O Modules
1734-PDN (12/24V dc)
0
1
NC
2
0
NC
Chas Chas
Gnd Gnd
4
C
6
4
V ac
7
V
5
L2/N
6
V
7
L1
NC = No Connection Chas Gnd = Chassis Ground
C = Common
V = 12/24V dc
L2/N
Module 1
2
A
Aret
B
Bret
Z
Zret
Out
0
Out
1
3
4
6
5
7
0
2
RET
1
2
5
-Vaux
-Vaux
4
+Vaux
+Vaux
3
7
Publication CIG-WD001B-EN-P - May 2005
I1
C+
C-
D = Data
C = Clock
0
RET
0
A, B, Z, Aret, Bret, and Zret = inputs
Chas Gnd = Chassis Ground
-Vaux = Auxiliary Supply
+Vaux = Auxiliary Supply
6
Module 1
1
Chas
Gnd
6
3
6
Module 2
1
A
Aret
B
Bret
Z
Zret
Out
0
Out
1
0
3
2
5
4
7
1
Chas
Gnd
Chas
Gnd
RET
0
RET
1
-Vaux
-Vaux
+Vaux
+Vaux
3
5
6
7
A, B, Z, Aret, Bret, and Zret = inputs
Chas Gnd = Chassis Ground
-Vaux = Auxiliary Supply
+Vaux = Auxiliary Supply
5
7
I1 = Digital Sourcing Input 1
V = SSI Sensor
1734-VHSC5
Chas
Gnd
4
V-
L2/N = ac Neutral
Module 2
1
V+
Shield
L1
1734-VHSC24
0
D-
4
This supply will be
connected to the
internal power bus.
NC = No Connection Chas Gnd = Chassis Ground
L1 = 120/240V ac
D+
2
3
Chas Chas
Gnd Gnd
This supply will
be connected to
the internal
power bus.
1
0
NC
2
3
1734-SSI
1
NC
5
C
V dc
1734-PDN 120/240V ac
Chapter
3
1734D POINTBlock I/O Modules
1734D-IA16, -IA16S
120V ac
Power
Field Power
0
V ac
NC
3
NC
NC
4
5
6
1
4
7
6
6
7
L1in L1in L1
L1
4
L2
7
L1
L1
7
0
L1
L1
L2
6
L1
L1
L1 = 120V ac
L2 = Return
NC
3
NC
NC
4
5
2
6
7
1
Repeat for RTB 2, 3, and 4
Outputs
2
3
L2
6
L1in L1in L1
6
L2
L1
7
L2
0
1
7
L2
2
In 3
Prox
Prox
4
5
5
L2
L2
L1
L1
L2
L2
6
7
L2
3
In 2
7
6
6
L2
5
3
4
L2
L2
6
L1
2
5
In 1
1
4
3
2
L2
0
1
3
4
7
L1
1
0
2
5
6
7
5
3
4
5
0
1
4
2
3
4
L2in L2in
0
1
0
7
1734D-IA8XOA8, -IA8XOA8S Input
Inputs
0
1
2
L2
RTB 0
RTB 1
RTB 2
RTB 3
RTB 4
This supply will be connected to the internal power bus.
NC = No Connection
Chas Gnd = Chassis Ground
L2/N = AC Return/Neutral L1 = AC Power
1
L2
In 0
NC
V ac
5
7
1734D-IA8XOA8, -IA8XOA8S
Field Power
Prox
4
RTB 0
RTB 1
RTB 2
RTB 3
RTB 4
This supply will be connected to the internal power bus.
NC = No Connection
Chas Gnd = Chassis Ground
L2/N = AC Return/Neutral L1 = AC Power
120V ac
Power
In 3
Prox
L2
6
L1
L1
3
In 2
5
L2
In 1
2
15
4
L2
6
3
14
5
L2
1
In 0
13
2
11
0
1
12
3
10
5
L2
0
9
2
7
4
L2
1
8
3
6
5
L2
5
2
3
0
1
4
3
2
L2in L2in
0
1
0
2
2
RTB 1
Inputs
0
1
NC
1734D-IA16, -IA16S Input
7
L1 = 120V ac
L2 = Return
Publication CIG-WD001B-EN-P - May 2005
3-2
1734D POINTBlock I/O Modules
1734D-IA8XOA8, -IA8XOA8S Output
0
1734D-IA8XOW8, -IA8XOW8S
120V ac
Power
1
Out 0
Out 1
Field Power
0
2
Out 2
Out 3
Load
4
6
L2
L2
L2
3
NC
NC
4
5
6
1
2
7
3
L2
L2
7
L2
L1
0B
L2
L1
1B
2A
L1
5A
3
4B
4
3A
5B
5
6A
6
7
2B
1
4A
2
5
6
7
0
1A
3
4
5
6
L1in L1in L1
L1 = 120V ac
L2 = Return
6
7
1
0A
2
3
4
5
6
5
2
2
0
1
4
3
4
Outputs
0
1
0
L2in L2in
V ac
7
NC
2
Load
5
L2
0
1
NC
3
Inputs
3B
7A
7
6B
7B
RTB 0
RTB 1
RTB 2
RTB 3
RTB 4
This supply will be connected to the internal power bus.
NC = No connection
L2/N = AC Return/Neutral L1 = AC Power
1734D-IA8XOW8, -IA8XOW8S Input
0
1
In 0
2-Wire
1734D-IA8XOW8, -IA8XOW8S Output
(Load Powered by External Power)
2
Prox
2
Prox
3
4
5
L2
Out 1A
Out 0B Out 1B
In 3
4
Power
Supply
1
Out 0A
3-Wire
3
In 2
0
Power
Supply
In 1
5
Out 2A Out 3A
L2
Load
6
L1
6
7
L1
Load
7
Out 2B Out 3B
Out = Output channel relay contacts
L1 = 120V ac
L2 = Return
L1 = 120V ac
L2 = Return
NOTE: This module cannot be powered by an internal power load.
1734D-IB16, -IB16S
12/24V dc
Power
Field Power
Inputs
RTB 1
0
0
0
1
NC
2
V ac
1734D-IB16, -IB16S Sink Input
NC
3
NC
NC
4
5
C
6
Vin
2
Vin
1
2
3
C
6
V
6
C
V
7
C
10
C
11
C
14
C
3-Wire
15
Prox
C
4
6
5
C
C
V
V
7
V
V = 12/24V dc
C = Common
3-Wire
3
2-Wire
In 3
C
7
V
Prox
In 1
2
In 2
RTB 0
RTB 1
RTB 2
RTB 3
RTB 4
This supply will be connected to the internal power bus.
NC = No Connection
Chas Gnd = Chassis Ground
C = Common
V = Supply
Publication CIG-WD001B-EN-P - May 2005
2-Wire
5
6
V
13
3
4
7
V
1
12
2
5
6
V
0
9
3
4
7
V
1
8
2
5
6
7
5
3
4
5
0
1
4
2
3
4
C
7
0
1
0
1
In 0
Repeat for RTB 2, 3, and 4
Prox
Prox
1734D POINTBlock I/O Modules
1734D-IB8XOB8E, -IB8XOB8ES
/
Inputs
Power
1734D-IB8XOB8E, -IB8XOB8ES Sink Input
Outputs
0
1
In 0
0
1
NC
2
V dc
0
NC
NC
NC
4
5
Cin
6
1
2
3
3
3
Cin
5
C
5
6
7
2
C
2
4
C
6
1
3
C
6
C
3-wire
2-wire
7
Prox
Prox
6
Power
Field
0
3
4
5
C
Load
7
C
C
V dc
V = 12/24V dc, C = Common
Field power is supplied from internal power bus
0
1
2
2
3
NC
NC
4
5
6
4
7
C
C
6
NC
NC
2-wire
C
C
V = 12/24V dc
C = Common
V
V
7
5B
5
4
5
2A
3A
6A
7A
6
7
6
7
Power
Supply
Out 1A
3
Out 0B Out 1B
Prox
3-wire
5
Out 2A Out 3A
Load
6
6
3
4B
4
1
Out 0A
4
5
4
2
1B
Chas Gnd = Chassis Ground
V = Supply
0
Power
Supply
2
Prox
7
3
5A
1734D-IB8XOW8, -IB8XOW8S Output
(Load Powered by External Power)
In 1
3
C
C
1
4A
1A
V 2B 3B 6B 7B
V
V
Vin Vin V
RTB 0
RTB 1
RTB 2
RTB 3
RTB 4
This supply will be connected to the internal power bus.
1
2
5
6
7
OB
7
4
5
2
3
6
3
0
1
0A
5
2
3
0
1
4
1
2
Cin
Cin
1734D-IB8XOW8, -IB8XOW8S Sink Input
In 0
7
Outputs
0
1
0
NC
NC = No Connection
C = Common
0
V
Inputs
NC
C
6
V
Prox
1734D-IB8XOW8, -IB8XOW8S
1
Load
C
V = 12/24V dc
C = Common
Out 2 Out 3
Load
Prox
5
C
C
Out 0 Out 1
Load
In 3
4
7
1734D-IB8XOB8E, -IB8XOB8ES Output
2
3
In 2
Vin Vin V
V
V
V
C
C
C
C
RTB 0
RTB 1
RTB 2
RTB 3
RTB 4
This supply will be connected to the internal power bus.
NC = No Connection
Chas Gnd = Chassis Ground
C = Common
V = Supply
0
In 1
2
5
C
6
7
5
3
4
5
6
7
1
4
2
3
7
5
0
1
0
3
4
C
6
0
1
4
2
2
4
7
0
1
0
3-3
7
Load
Out 2B Out 3B
Out = Output channel relay contacts
Power Supply = can range from +5V dc to 240V ac
C = Common
NOTE: This module cannot be powered by an internal power load.
Publication CIG-WD001B-EN-P - May 2005
3-4
1734D POINTBlock I/O Modules
Notes:
Publication CIG-WD001B-EN-P - May 2005
Chapter
4
1738 ArmorPoint
1738-232ASCM12
1738-485ASCM12
(view into connector)
Pin 1 Tx Pin 2 Tx +
Pin 3 Rx +
Pin 4 Rx Pin 5 No Connect
(view into connector)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
No Connect
Tx +
Rx +
Common
No Connect
1738-ACNR
1738-ADN12
Male In Connector
(view into connector)
Pin 1 Pin 2 Pin 3 Pin 4 -
User Power +
Adapter Power +
Adapter Power User Power -
Male In Connector
Female Out Connector
(view into connector)
Pin 1 Drain
Pin 2 +V
Pin 3 -V
Pin 4 CAN_High
Pin 5 CAN_Low
DeviceNet Auxiliary Power
Male In Connector
(view into connector)
Pin 1
User Power +
Pin 2
Adapter Power +
Pin 3
Adapter Power Pin 4
User Power -
1
Publication CIG-WD001B-EN-P - May 2005
4-2
1738 ArmorPoint
1738-ADN18
1738-ADN18P
Male In Connector
Male In Connector
(view into connector)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Female Out Connector
(view into connector)
Pin 1 Drain
Pin 2 +V
Pin 3 -V
Pin 4 CAN_High
Pin 5 CAN_Low
Drain
+V
-V
CAN_High
CAN_Low
DeviceNet Auxiliary Power
DeviceNet Auxiliary Power
Male In Connector
Male In Connector
(view into connector)
Pin 1
User Power +
Pin 2
Adapter Power +
Pin 3
Adapter Power Pin 4
User Power -
(view into connector)
Pin 1
User Power +
Pin 2
Adapter Power +
Pin 3
Adapter Power Pin 4
User Power -
1738-ADNX
Male In Connector
1738-AENT
Female Out Connector
Network Connector
(Subnet out)
Female In Connector
(view into connector)
Pin 1 Tx +
Pin 2 Rx +
Pin 3 Tx Pin 4 Rx -
(view into connector)
Pin 1 Drain
Pin 2 +V
Pin 3 -V
Pin 4 CAN_High
Pin 5 CAN_Low
Auxiliary Power
DeviceNet Auxiliary Power
Male In Connector
(view into connector)
Pin 1
User Power +
Adapter/Subnet +
Pin 2
Adapter/Subnet Pin 3
Pin 4
User Power -
Publication CIG-WD001B-EN-P - May 2005
Male In Connector
(view into connector)
Pin 1 User Power +
Pin 2 Adapter Power +
Pin 3 Adapter Power Pin 4 User Power -
1738 ArmorPoint
1738-APB
4-3
1738-EP24DC
Male In Connector
Female In Connector
(view into connector)
Pin 1 +5VBUS
Pin 2 A-Line
Pin 3 GNDBUS
Pin 4 B-Line!
Pin 5 Shield
Male In Connector
(view into connector)
Pin 1 User Power +
Pin 2 Adapter +
Pin 3 Adapter Pin 4 User Power -
Male Auxiliary
Male In connector
((view into connector)
Pin 1 User Power Pin 2 Adapter Power Pin 3 Protective GND
Pin 4 Adapter Power +
Pin 5 User Power +
IMPORTANT
Profibus Adapter Network connections have earth grounded metal
rings. This should be considered when choosing shielded cables
and grounding techniques.
1738-EXT1, -EXT3
Module will bridge the extension unit and the base
1738-FPD
Module will bridge the extension unit and the base
1738-IA2M12AC3
(view into connector)
Pin 1 Chassis
Pin 2 L1
Pin 3 Input 0 (M12-A)
Input 1 (M12-B)
Male In Connector
(view into connector)
Pin 1 User Power +
Pin 2 No Connect
Pin 3 No Connect
Pin 4 User Power -
1738-IA2M12AC4
(view into connector)
Pin 1 L1
Pin 2 L2/N
Pin 3 Input 0 (M12-A)
Input 1 (M12-B)
Pin 4 Chassis
Publication CIG-WD001B-EN-P - May 2005
4-4
1738 ArmorPoint
1738-IB2M12
1738-IB4M12
(view into connector)
Pin 1 24V dc
Pin 2 No Connect
Pin 3 Common
Pin 4 Input 0 (M12-A)
Input 1 (M12-B)
Input 2 (M12-C)
Input 3 (M12-D)
Pin 5 No Connect
(view into connector)
Pin 1 24V dc
Pin 2 No Connect
Pin 3 Common
Pin 4 Input 0 (M12-A)
Input 1 (M12-B)
Pin 5 No Connect
1738-IB4M8
1738-IB8M12
(view into connector)
Pin 1 24V dc
Pin 2 I nput 1 (M12-A)
Input 3 (M12-B)
Input 5 (M12-C)
Input 7 (M12-D)
Pin 3 Common
Pin 4 Input 0 (M12-A)
Input 2 (M12-B)
Input 4 (M12-C)
Input 6 (M12-D)
Pin 5 No Connect
(view into connector)
Pin 1 24V dc
Pin 3 Common
Pin 4 Input 0 (M8-A)
Input 1 (M8-B)
Input 2 (M8-C)
Input 3 (M8-D)
1738-IB8M23
1
8
9
7
2
10
12
6
3
11
4
5
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
1738-IB8M8
(view into connector)
Pin 1 24V dc
Pin 4 Input 0 (M8-A)
Pin 3 Common
Input 1 (M8-B)
Input 2 (M8-C)
Input 3 (M8-D)
Input 4 (M8-E)
Input 5 (M8-F)
Input 6 (M8-G)
Input 7 (M8-H)
(view into connector)
Input 0
Pin 7 Input 6
Input 1
Pin 8 Input 7
Input 2
Pin 9 Return (Com)
Input 3
Pin 10 Return (Com)
Input 4
Pin 11 24V dc
Input 5
Pin 12 Chassis
1738-IE2CM12
IMPORTANT
1738-IE2VM12
(view into connector)
(view into connector)
Pin 1 24V dc
Pin 2 Input 0 (M12-A)
Input 1 (M12-B)
Pin 3 Common
Pin 4 Common
Pin 5 No Connect
Pin 1 24V dc
Pin 2 Input 0 (M12-A)
Input 1 (M12-B)
Pin 3 Common
Pin 4 Common
Pin 5 No Connect
Analog and specialty modules have earth
grounded metal rings. This should be
considered when choosing shielded cables
and grounding techniques.
Publication CIG-WD001B-EN-P - May 2005
IMPORTANT
Analog and specialty modules have earth
grounded metal rings. This should be
considered when choosing shielded cables
and grounding techniques.
1738 ArmorPoint
1738-IJM23
1
8
9
7
2
10
12
6
3
11
4
5
1738-IR2M12
(view into connector)
(view into connector)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
Pin 1
Pin 2
+A
~A
+B
~B
+Z
~Z
Chassis
Chassis
Return (Com)
Return (Com)
5V dc
Chassis
Pin 3
Pin 4
Pin 5
IMPORTANT
IMPORTANT
Analog and specialty modules have earth
grounded metal rings. This should be
considered when choosing shielded cables
and grounding techniques.
1738-IT2IM12
No Connect
Input 0A (M12-A)
Input 1A (M12-B)
Input 0C (M12-A)
Input 1C (M12-B)
Input 0B (M12-A)
Input 1B (M12-B)
No Connect
Analog and specialty modules have earth
grounded metal rings. This should be
considered when choosing shielded cables
and grounding techniques.
1738-IV4M12
(view into connector)
Pin 1 24V dc
Pin 2 No Connect
Pin 3 Common
Pin 4 Input 0 (M12-A)
Input 1 (M12-B)
Input 2 (M12-C)
Input 3 (M12-D)
Pin 5 No Connect
(view into connector)
Pin 1 CJC +
Pin 2 TC 0 + (M12-A)
TC 1 + (M12-B)
Pin 3 CJC Pin 4 TC 0 - (M12-A)
TC 1 - (M12-B)
Pin 5 No Connect
IMPORTANT
4-5
Analog and specialty modules have earth
grounded metal rings. This should be
considered when choosing shielded cables
and grounding techniques.
1738-IV8M12
(view into connector)
Pin 1 24V dc
Pin 2 Input 1 (M12-A)
Input 3 (M12-B)
Input 5 (M12-C)
Input 7 (M12-D)
Pin 3 Common
Pin 4 Input 0 (M12-A)
Input 2 (M12-B)
Input 4 (M12-C)
Input 6 (M12-D)
Pin 5 No Connect
1738-IV8M23
1
8
9
7
2
10
12
6
3
11
4
5
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
(view into connector)
Input 0
Pin 7 Input 6
Input 1
Pin 8 Input 7
Input 2
Pin 9 Return (Com)
Input 3
Pin 10 Return (Com)
Input 4
Pin 11 24V dc
Input 5
Pin 12 Chassis
Publication CIG-WD001B-EN-P - May 2005
4-6
1738 ArmorPoint
1738-IV8M8
1738-OA2M12AC3
(view into connector)
Pin 1 24V dc
Pin 4 Input 0 (M8-A)
Pin 3 Common
Input 1 (M8-B)
Input 2 (M8-C)
Input 3 (M8-D)
Input 4 (M8-E)
Input 5 (M8-F)
Input 6 (M8-G)
Input 7 (M8-H)
(view into connector)
Pin 1 Chassis
Pin 2 L2/N
Pin 3 Output 0 (M12-A)
Output 1 (M12-B)
1738-OB2EM12
1738-OB2EPM12
(view into connector)
Pin 1 24V dc
Pin 2 No Connect
Pin 3 Common
Pin 4 Output 0 (M12-A)
Output 1 (M12-B)
Pin 5 No Connect
(view into connector)
Pin 1 24V dc
Pin 2 No Connect
Pin 3 Common
Pin 4 Output 0 (M12-A)
Output 1 (M12-B)
Pin 5 No Connect
1738-OB4EM12
1738-OB4EM8
(view into connector)
Pin 1 24V dc
Pin 2 No Connect
Pin 3 Common
Pin 4 Output 0 (M12-A)
Output 1 (M12-B)
Output 2 (M12-C)
Output 3 (M12-D)
Pin 5 No Connect
(view into connector)
Pin 1 24V dc
Pin 3 Common
Pin 4 Output 0 (M8-A)
Output 1 (M8-B)
Output 2 (M8-C)
Output 3 (M8-D)
1738-OB8EM12
(view into connector)
Pin 1 24V dc
Pin 2 Output 1 (M12-A)
Output 3 (M12-B)
Output 5 (M12-C)
Output 7 (M12-D)
Pin 3 Common
Pin 4 Output 0 (M12-A)
Output 2 (M12-B)
Output 4 (M12-C)
Output 6 (M12-D)
Pin 5 No Connect
Publication CIG-WD001B-EN-P - May 2005
1738-OB8EM23
1
8
9
7
2
10
12
6
3
11
4
5
(view into connector)
Pin 1 Output 0
Pin 2 Output 1
Pin 3 Output 2
Pin 4 Output 3
Pin 5 Output 4
Pin 6 Output 5
Pin 7 Output 6
Pin 8 Output 7
Pin 9 Return (Com)
Pin 10 Return (Com)
Pin 11 24V dc
Pin 12 Chassis
1738 ArmorPoint
1738-OB8EM8
1738-OE2CM12
(view into connector)
Pin 1 24V dc
Pin 3 Common
Pin 4 Output 0 (M8-A)
Output 1 (M8-B)
Output 2 (M8-C)
Output 3 (M8-D)
Output 4 (M8-E)
Output 5 (M8-F)
Output 6 (M8-G)
Output 7 (M8-H)
(view into connector)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
IMPORTANT
1738-OE2VM12
Pin 2
Pin 3
Pin 4
Pin 5
IMPORTANT
Output 0 (M12-A)
Output 1 (M12-B)
24V dc
Common
Common
No Connect
Analog and specialty modules have earth
grounded metal rings. This should be
considered when choosing shielded cables
and grounding techniques.
1738-OV4EM12
(view into connector)
Pin 1
4-7
Output 0 (M12-A)
Output 1 (M12-B)
24V dc
Common
Common
No Connect
(view into connector)
Pin 1 24V dc
Pin 2 No Connect
Pin 3 Common
Pin 4 Output 0 (M12-A)
Output 1 (M12-B)
Output 2 (M12-C)
Output 3 (M12-D)
Pin 5 No Connect
Analog and specialty modules have earth
grounded metal rings. This should be
considered when choosing shielded cables
and grounding techniques.
1738-OW4M12
(view into connector)
Pin 1 24V dc
Pin 2 Output 0B (M12-A)
Output 1B (M12-B)
Output 2B (M12-C)
Output 3B (M12-D)
Pin 3 Common
Pin 4 Output 0A (M12-A)
Output 1A (M12-B)
Output 2A (M12-C)
Output 3A (M12-D)
Pin 5 No Connect
1738-OW4M12AC4
(view into connector)
Pin 1 L1
Pin 2 L2/N
Pin 3 Output 0A (M12-A)
Output 1A (M12-B)
Output 2A (M12-C)
Output 3A (M12-D)
Pin 4 Output 0B (M12-A)
Output 1B (M12-B)
Output 2B (M12-C)
Output 3B (M12-D)
Publication CIG-WD001B-EN-P - May 2005
4-8
1738 ArmorPoint
1738-SSIM23
1738-VHSC24M23
(view into connector)
1
8
9
7
2
10
12
6
3
11
4
IMPORTANT
5
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
Data +
Data V+
VShield
Input 0
Clock +
Clock Return (Com)
Return (Com)
24 V dc
Chassis
Analog and specialty modules have earth
grounded metal rings. This should be
considered when choosing shielded cables
and grounding techniques.
Publication CIG-WD001B-EN-P - May 2005
(view into connector)
1
8
9
7
2
10
12
6
3
11
4
IMPORTANT
5
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
+A
~A
+B
~B
+Z
~Z
Output 0
Output 1
Return (Com)
Return (Com)
24V dc
Chassis
Analog and specialty modules have earth
grounded metal rings. This should be
considered when choosing shielded cables
and grounding techniques.
Chapter
5
1746 I/O Modules
1746-BLM
Desc riptio n
14
40
2
: : : : : : : : : : : : : : : : : : : :
1
39
1492-IFM40F
+
13
16
40
2
15
1
39
Axis 1
Axis 2
Axis 3
Axis 4
Dig ital OUT+ (+24EXT )
17
18
13
14
9
10
5
6
Digit al I N-
19
15
11
7
Digit al I N+
20
16
12
8
Re se rve d
Digit al O UT-
-
digital output
sync output
+ 24V EXT
+
digital input
start-of-drop trigger
- dc common
22 +
24V dc
supply
21 -
4, 3, 2, 1
-24V dc RET
21
+24V dc EX T
22
An al og OUT- (GND)
23
27
31
35
An al og OUT+
24
28
32
36
An al og IN-
25
26
29
30
33
34
37
38
An al og IN+
We recommend making connections to the 1746-BLM module with:
-- Interface module (1492-IFM40F)
-- Interface cable (1492-CABLE010H)
System
Excitation- (-10V)
39
Excitation+ (+1 0V)
40
1746-BTM
Retaining Screw
CJC A+
CJC Assembly
Channel 0+
CJC A-
Channel 0Channel 1+
ATTENTION
Channel 1-
Do NOT use these
connections
Channel 2+
Do not remove or loosen the cold junction compensating
thermistors located on the terminal block. Both thermistors
are critical to ensure accurate thermocouple input
readings at each channel. The module will not operate in the
thermocouple mode if a thermistor is removed
Channel 2Channel 3+
CJC B+
CJC Assembly
CJC BRetaining Screw
Channel 3spare part catalog number:
1746-RT32
n/c
1746-FIO4I
1746-FIO4V
+
+
analog
source
-
earth
ground
Jumper
unused
inputs.
LOAD
earth
ground
1
Do not jumper
unused outputs.
0
1
2
IN 0+
IN 0ANL COM
3
4
5
IN 1+
IN 1ANL COM
6
7
8
not used
OUT 0
ANL COM
9
10
11
not used
OUT 1
ANL COM
analog
source
-
earth
ground
Jumper
unused
inputs.
LOAD
earth
ground
Do not jumper
unused outputs.
0
1
2
IN 0+
IN 0ANL COM
3
4
5
IN 1+
IN 1ANL COM
6
7
8
not used
OUT 0
ANL COM
9
10
11
not used
OUT 1
ANL COM
Publication CIG-WD001B-EN-P - May 2005
5-2
1746 I/O Modules
1746-HSCE Differential Encoder
cab le (1)
+ V DC
COM
VS
GN D
Input and Output Connections
Power
Supply
Belden 9503 or equivalent
305m (1000ft) max length
Upper Retaining Screw Maximum
Torque = 0.7 to 0.9 Nm (6 to 8 in-lbs)
Allen-Bradley
845H Series
differential
encoder
Discrete Output Wiring
The user must supply
the external VDC.
A
A(+)
A
A(-)
B
B(+)
B
B(-)
Z
Z(+)
Z(-)
Z
Shie ld (2)
Terminal Wiring
max. #14 AWG (2mm2)
max. 2 wires per terminal
max. torque: 0.9Nm (8 in-lbs)
encoder connector
housing
ON
SW1
1 234
OF F
(all switches ON)
Earth
Module Inputs
1. Refer to your encoder manual for proper cable type and length.
2. Due to the topology of the module’s input circuits, terminating the shield at the encoder end
provides the highest immunity to EMI interference. Connect EARTH ground directly to the encoder
connector housing.
Limit Switch and
Encoder Input Wiring
Differential Encoder Output Waveforms
Lower Retaining Screw Maximum
Torque = 0.7 to 0.9 Nm (6 to 8 in-lbs)
The figure below shows the different encoder output waveforms. If your encoder matches these
waveforms, the encoder signals can be directly connected to the associated screw terminals on
the module. For example, the A lead from the encoder is connected to the module’s A+ screw.
If your encoder does not match these waveforms, some wiring modifications may be necessary.
See the High-Speed Counter Module User Manual, publication 1746-6.5 for a description of
these modifications.
A
A
B
B
Z
Z
1746-HSCE Limit Switch (12V dc Hard Contact)
Input and Output Connections
1746-HSCE module
Upper Retaining Screw Maximum
Torque = 0.7 to 0.9 Nm (6 to 8 in-lbs)
Hard Contact Limit Switch LS (24V dc)
LS (12V dc )
VS
Discrete Output Wiring
The user must supply
the external VDC.
12V dc
+
-
CO M
LS (5V dc )
LS COM
Do not connect LS (5V dc) or LS
(12V dc) Terminals
Terminal Wiring
max. #14 AWG (2mm2)
max. 2 wires per terminal
max. torque: 0.9Nm (8 in-lbs)
Limit Switch and
Encoder Input Wiring
Lower Retaining Screw Maximum
Torque = 0.7 to 0.9 Nm (6 to 8 in-lbs)
Publication CIG-WD001B-EN-P - May 2005
321
Jumper placed for
10 ms filtering
Connect only one LS input range at a time,
or the module will be damaged.
JW 1
1746 I/O Modules
5-3
1746-HSCE Limit Switch (24V dc Hard Contact)
Input and Output Connections
Hard Contact Limit Switch
LS (24V dc)
VS
LS (12V dc)
+
24V dc
1746-HSCE module
LS (5V dc)
CO M
LS COM
Do not connect LS (5V dc) or LS
(12V dc) Terminals
321
Jumper placed for
10 ms filtering
JW 1
Connect only one LS input range at a time,
or the module will be damaged.
1746-HSCE Limit Switch (5V dc Solid State)
Input and Output Connections
1746-HSCE module
Solid State Limit Switch
COM
VS
VS
+
5V dc
COM
OUT
LS (24V dc)
LS (12V dc)
LS (5V dc)
LS COM
Do not connect LS (12V dc) or LS
(24V dc) Terminals
Jumper placed for
300 µs filtering
321
JW1
Connect only one LS input range at a time,
or the module will be damaged.
Publication CIG-WD001B-EN-P - May 2005
5-4
1746 I/O Modules
1746-HSCE Outputs
Input and Output Connections
1746-HSCE module
VDC
OUT 0
User Supplied
24V dc
+
OUT 1
-
OUT 2
All switches OFF
ON
OUT 3
DC COM
1 234
OFF
Dip Switch SW2
wiring terminals
Do not use incandescent lamps as output indicators. The high peak inrush current
required to heat the filament can damage the module’s output circuits. Use LED
type indicators that satisfy the output circuit ratings, such as Allen-Bradley 800A
and 800T LED indicators.
The outputs are not electrically isolated from each other. (They are referenced to the same output
common terminal.) However, outputs are isolated from the rest of the circuitry to a level of 1500 volts.
1746-HSCE Single-Ended (Discrete Devices)
Input and Output Connections
+V DC
CO M
proximity sensor with
VS
OU T
CO M
R1
photoelectric sensor with open
A(+)
A(-)
solid-state
switch
(5V output)
VS
OU T
CO M
Power
Supply
R2
VS
OU T
CO M
B(+)
B(-)
Z(+)
Z(-)
ON
1 2 34
SW1
OF F
(All switches OFF)
Module Inputs
I M PORTA NT
This diagram shows the sensors operation from a common power supply.
Separate power supplies for each circuit can be used.
The resistor (R1) value depends on the power supply value (VS).
The pullup resistor (R2) value depends on the power supply value (VS).
Publication CIG-WD001B-EN-P - May 2005
1746 I/O Modules
5-5
1746-HSCE Single-Ended Encoder (Open-Collector)
Input and Output Connections
cable (1)
VS
GN D
+ V DC
CO M
Power
Supply
(3)
R
Allen-Bradley
845H Series
differential
encoder
Shield (2)
A
A(+)
A(-)
B
B(+)
B(-)
Z(+)
Z(-)
Z
ON
Belden 9503 or equivalent
305m (1000tft) max length
SW1
encoder connector
housing
1 234
OF F
(All switches OFF)
Earth
Module Inputs
(1) Refer to your encoder manual for proper cable type and length.
(2) Due to the topology of the module’s input circuits, terminating the shield at the encoder end provides the highest immunity
to EMI interference. Connect EARTH ground directly to the encoder connector housing.
(3) The pullup resistor (R) value depends on the power supply value (VS). The table below lists the resistor values for typical
power supply values. These resistors must be located at the encoder end of the cable.
VS V alue
R Value
+5V dc
150 ohm 1/4W 5%
Max imu m Outpu t Leak age
6.3 mA
+12V dc
1800 ohm 1/4W 5%
1.5 mA
+24V dc
4700 ohm 1/4W 5%
1.2 mA
Single-Ended Encoder Output Waveforms
The figure below shows the single-ended output waveforms. When the waveform
is low, the encoder output transistor is ON.
A
low = transistor ON
high = transistor OFF
B
Z
1746-HSCE Single-Ended Encoder (Sourcing)
Input and Output Connections
cable (1)
VS
+ V DC
COM
GND
Power
Supply
Belden 9503 or equivalent
305m (1000tft) max length
A(+)
A
R
single ended
encoder(4)
(3) A(-)
B(+)
B(-)
Z(+)
R (3) Z(-)
B
R
Z
(3)
Sh ield (2)
ON
SW1
1 2 34
OF F
(All switches OFF)
Module Inputs
Earth
(1) Refer to your encoder manual for proper cable type and length.
(2) Due to the topology of the module’s input circuits, terminating the shield at the encoder end provides the highest immunity
to EMI interference. Connect EARTH ground directly to the encoder connector housing.
(3) The resistor (R) value depends on the power supply value (VS). The table below lists the resistor values for typical power
supply values. These resistors must be located at the encoder end of the cable.
(4) The Allen-Bradley 845H sourcing encoder is not compatible with this module.
VS Value
R Value
+5V dc
no resistor needed
Max imu m Outpu t Leak age
6.3 µA
+12V dc
1800 ohm 1/4W 5%
1.5 µA
+24V dc
4700 ohm 1/4W 5%
1.2 µA
Single-Ended Encoder Output Waveforms (Sourcing)
The figure below shows the single-ended encoder output waveforms. When the
waveform is low, the encoder output transistor is OFF.
low = transistor OFF
high = transistor ON
A
B
Z
Publication CIG-WD001B-EN-P - May 2005
5-6
1746 I/O Modules
1746-HSCE2 – Differential Encoder
Cabl e (1)
Input and Output Connections
+VDC
VS
GND
COM
A
A(+)
A
A(–)
B
B(+)
B
B(–)
Z
Z(+)
Power
S upply
Release screw
A1 +
A1 -
B1 +
B1-
Z1+
Z1-
A2 +
Allen-Bradley
845H Series
differential
encoder
A2-
B2 +
B2 -
Z2+
Shi e ld
Z2-
Output common
shield/housing
Connect only if housing is electronically
isolated from the motor and ground.
OUTPUT 0
OUTPUT 1
OUTPUT 2
OUTPUT 3
Release screw
Z(–)
Z
+V dc
E arth
Module Inputs
1 Refer to your encoder manual for proper cable type. The type of cable used should be twisted
pair, individually shielded cable with a maximum length of 300m (1000 ft.).
Differential Encoder Output Waveforms
The figure below shows the different encoder output waveforms. If your encoder matches these
waveforms, the encoder signals can be directly connected to the associated screw terminals on
the module. For example, the A lead from the encoder is connected to the module’s A+ screw.
If your encoder does not match these waveforms, some wiring modifications may be necessary.
See the user’s manual for your encoder.
A
A
B
B
Z
Z
1746-HSCE2 Single-Ended Encoder (Open-Collector)
cab le (1 )
Input and Output Connections
+VDC
COM
Release screw
A1 +
B1 +
VS
GND
R
A1 -
B2 +
Z2+
Output common
OUTPUT 1
OUTPUT 3
Release screw
A(–)
Z
B(+)
B
Z1A2B2 Z2OUTPUT 0
OUTPUT 2
+V dc
The figure below shows the single-ended encoder
output waveforms. When the waveform is low, the
encoder output transistor is on. When the waveform
is high, the encoder output transistor is off.
B
A(+)
B1-
Single-Ended Encoder Output Waveforms
A
(2)
A
Z1+
A2 +
B(–)
Allen-Bradley
845H Series
differential
encoder
Z(+)
Z
Z(–)
shi e ld
shield/housing
Connect only if housing is electronically
isolated from the motor and ground.
Earth
Module Inputs
1. Refer to your encoder manual for proper cable type. The type of cable used should be twisted pair,
individually shielded cable with a maximum length of 300m (1000 ft.).(2)
2. External resistors are needed if not internal to the encoder. The pull-up resistor (R) value depends on
the power supply value. The table below shows resistor values for typical supply voltages. To calculate
the resistor value, use one of the following formulas:
For 5V dc jumper position: R =
(Vcc - Vmin)
Imin
For 24V dc jumper position: R =
[
(Vcc - Vmin)
- 1KΩ
Imin
[
where: R = pull-up resistor value
Vcc = power supply voltage
Vmin = 4.2V dc
Imin = 6.3mA
Power Supply Voltage (Vcc)
5V dc
12 V dc
24 V dc
Pull-up Resistor Value (R)1
127 W
238 W
21 40 W
1 Resistance values may change, depending upon your application.
Publication CIG-WD001B-EN-P - May 2005
P o wer
Su ppl y
1746 I/O Modules
5-7
1746-HSCE2 Single-Ended (Discrete Devices)
+VDC
Input and Output Connections
COM
Release screw
A1 +
B1 +
proximity sensor
A1 -
VS
A2 +
Z2+
Output common
OUTPUT 1
OUTPUT 3
Release screw
VS
solid-state
switch
A2-
OUT
B(+)
COM
B(–)
VS
B2 -
OUT
Z2-
OUTPUT 2
A(–)
COM
Z1-
OUTPUT 0
A(+)
OUT
B1-
Z1+
B2 +
Power
S uppl y
R
(1)
Z(+)
COM
Z(–)
photoelectric sensor
with open collector
sinking output
+V dc
Module Inputs
1. External resistors are needed if not internal to the encoder. The pull-up resistor (R) value depends on
the power supply value. The table below shows resistor values for typical supply voltages. To calculate
the resistor value, use one of the following formulas:
For 5V dc jumper position: R =
(Vcc - Vmin)
Imin
For 24V dc jumper position: R =
[
(Vcc - Vmin)
- 1KΩ
Imin
where: R = pull-up resistor value
Vcc = power supply voltage
Vmin = 4.2V dc
Imin = 6.3mA
[
Power Supply Voltage (Vcc)
5V dc
12 V dc
24 V dc
Pull-up Resistor Value (R)1
127 W
238 W
21 40 W
1 Resistance values may change, depending upon your application.
Publication CIG-WD001B-EN-P - May 2005
5-8
1746 I/O Modules
1746-HSRV – Wiring a 15V Encoder
ENCODER
C H A. HI
A
1
CH A. LO
A
AB SHLD
CH B. HI
B
1
CH B. LO
B
Z SHLD
CH Z. HI
B
Z
1
CH Z. LO
I
C
J
Z
ENCODER POWER
+5 V
A
3
Optical
Encoder
G
F D
+15V Return
2
RET
Case
Ground
+1 5 V
SHLD
+15V
1
Use three pair 22 gauge individually twisted and shielded cable.
2
Use one pair 18 gauge twisted and shielded cable.
3
Encoders must have +5V compatible differential line drive outputs on channels A, B, and Z (DS 8830 or equivalent
(845H)).
Wiring the power supply
+5V
+5 V COMM
L1
14 AWG
+1 5V
L2
+/ - 15V COMM
E X T P O W E R
- 1 5V
+5 V
RET
+15V
- /+ R E T
+ 24V P o wer Supply
- 15V
+2 4
+24R E T
E G ND
14 AWG
AC HI
AC L O
+2 4V
+24 V R E T
14 AWG (3)
14 AWG
A C L ine
Electrical Cabinet
Ground Bus
Publication CIG-WD001B-EN-P - May 2005
H
1746 I/O Modules
5-9
1746-HSRV – Wiring a 5V Encoder
ENCODER
C H A. HI
A
1
CH A. LO
A
AB SHLD
CH B. HI
B
1
CH B. LO
B
Z SHLD
CH Z. HI
Z
1
CH Z. LO
Z
ENCODER POWER
+5 V
I
H
B
A
3
Optical
Encoder
C
J
F
D
G
+5V
2
RET
+1 5 V
+5V Return
SHLD
Case
Ground
1
Use three pair 22 gauge individually twisted and shielded cable.
2
Use one pair 18 gauge twisted and shielded cable.
3
Encoders must have +5V compatible differential line drive outputs on channels A, B, and Z (DS 8830 or equivalent
(845H)).
Wiring the power supply
+5V
+5 V COMM
L1
14 AWG
+1 5V
L2
+/ - 15V COMM
E X T P O W E R
- 1 5V
+5 V
RET
+15V
- /+ R E T
+ 24V P o wer Supply
- 15V
+2 4
+24R E T
E G ND
14 AWG
AC H I
AC L O
+2 4V
+24 V R E T
14 AWG (3)
14 AWG
A C L ine
Electrical Cabinet
Ground Bus
Publication CIG-WD001B-EN-P - May 2005
5-10
1746 I/O Modules
1746-HSTP1 – Wiring a 15V Encoder
7-24V DC user power (1)
CW + or non directional pulse output (2)
CW - or non directional pulse output (3)
CW + pulse or direction signal output (4)
CCW - pulse or direction signal output (5)
External interrupt input (6)
Home limit switch input (7)
Home Proximity limit switch input (8)
CW limit switch input (9)
1
CCW limit switch input (10)
A
A
Pulse train enable/disable input (11)
1
A Hi (Loopback + non directional pulse) (12)
B
H
A Lo (Loopback - non directional pulse) (13)
1
B Hi (Loopback + direction) (14)
3
A-B 845H
Optical
Encoder
I
Z
C
Z
B Lo (Loopback - direction (15)
A
B
B
J
+ Encoder Marker (16)
D
G
F
- Encoder Marker (17)
+15 VDC
0 V user power (DC common) (18)
Case Ground
DC
SOURCE
16 AWG
Return
16 AWG
Electrical Cabinet
Ground Bus
1. Use 3-pair, #22 gauge individually twisted and shielded pair, Belden 9504 or equivalent.
2. Use 1-pair, #18 gauge twisted and shielded cable.
3. Encoders must have +5V compatible differential line drive outputs on channels A, B and Z. (DS8830 or equivalent - Allen-Bradley 845H).
4. +15V from encoder power source - connect encoder return to 0V user power (DC common) at the power supply sources.
1746-HSTP1 – Wiring a 5V Encoder
7-24V DC user power (1)
CW + or non directional pulse output (2)
CW - or non directional pulse output (3)
CW + pulse or direction signal output (4)
CCW - pulse or direction signal output (5)
External interrupt input (6)
Home limit switch input (7)
Home Proximity limit switch input (8)
CW limit switch input (9)
CCW limit switch input (10)
1
1
A Hi (Loopback + non directional pulse) (12)
A
A
Pulse train enable/disable input (11)
B
H
A Lo (Loopback - non directional pulse) (13)
1
B Hi (Loopback + direction) (14)
C
J
+ Encoder Marker (16)
- Encoder Marker (17)
0 V user power (DC common) (18)
DC
SOURCE
16 AWG
3
A-B 845H
Optical
Encoder
I
Z
Z
B Lo (Loopback - direction (15)
A
B
B
+5V
D
F
G
Case Ground
Return
16 AWG
Electrical Cabinet
Ground Bus
1. Use 3-pair, #22 gauge individually twisted and shielded pair, Belden 9504 or equivalent.
2. Use 1-pair, #18 gauge twisted and shielded cable.
3. Encoders must have +5V compatible differential line drive outputs on channels A, B and Z. (DS8830 or equivalent - Allen-Bradley 845H).
4. +5V from encoder power source - connect encoder return to 0V user power (DC common) at the power supply sources.
Publication CIG-WD001B-EN-P - May 2005
1746 I/O Modules
1746-IA16
1746-IA4
1746-IA8
100/120V ac
100/120V ac
L1
100/120V ac
NOT
USED
IN 0
0
1
IN 2
2
3
IN 5
6
IN 7
IN 3
L1
10
IN 9
12
IN 1 1
IN 4
IN 1
IN 5
11
IN 10
100/120V ac
IN 2
IN 6
13
IN 12
14
IN 13
16
IN 15
IN 3
IN 7
15
IN 14
L2
AC COM
17
L2
AC COM
L2
AC COM
AC COM
COMMONS
CONNECTED
INTERNALLY
COMMONS
CONNECTED
INTERNALLY
SLC (decimal)
PLC (octal)
1746-IB16
24V dc sinking
24V dc Sinking
0 IN 1
1
IN 2
2
IN 3
3
IN 4
dc Com 1(2)
COM 1
COM 3
dc Com 3(2)
dc Com 1(2)
COM 1
COM 3
dc Com 3(2)
IN 0
+V dc 1
4 IN 5
6 IN 7
IN 8 6
10 IN 9
12 IN 1 1
14
IN 14
DC
COM
IN 18
IN 2
2
2
IN 19
IN 3
3
3
IN 4
13
IN 20
4
4
IN 13
IN 5
15
IN 21
5
16 IN 15
IN 6
17
5
IN 22
6
6
IN 23
IN 7
DC COM
COMMONS CONNECTED
INTERNALLY
1
1
7
Connector
Key
7
7
IN 24
IN 8
10
10
SLC (decimal)
IN 25
IN 9
PLC (octal)
11
11
IN 26
IN 10
12
12
IN 27
IN 1 1
13
13
IN 12
IN 28
14
14
IN 13
IN 29
15
15
IN 14
IN 30
16
16
IN 15
+V dc 2
IN 31
dc Com 2(2)
+V dc 4
17
17
dc Com 2(2)
+V dc 3
0
IN 17
IN 1
11
IN 10
IN 16
0
5
IN 6
IN 12
Wire
Group 3
Wire
Group 1
IN 0
AC COM
1746-IB32
+DC
-DC
100/120V ac
IN 0
7
IN 8
24V dc
IN 2
NOT
USED
5
IN 6
100/120V ac
IN 0
IN 1
NOT
USED
IN 3
IN 4
4
L1
NOT
USED
IN 1
5-11
COM 2
COM 4
COM 2
COM 4
Wire
Group 2
dc Com 4(2)
dc Com 4(2)
Wire
Group 4
SLC (decimal)
(1)
PLC (octal)
(1)
See decimal and octal coding information at the top of the page.
(2)
The dc Com pins on the 1746-IB32 input module are isolated between the four groups and the two com pins in each group
are connected internally. To maintain group isolation provided by 32-point I/O modules, use a 1492 terminal block that
provides group isolation. Consult 1492 documentation or your Allen-Bradley Sales Office for additional information.
Publication CIG-WD001B-EN-P - May 2005
5-12
1746 I/O Modules
1746-IB8
1746-IC16
24V dc Sinking
48V dc Sinking
+DC
+DC
IN 0
IN 0
IN 1
IN 2
0 IN 1
1
IN 3
2
IN 2
3
IN 4
48V dc
IN 3
24V dc
IN 4
4 IN 5
5
IN 6
6 IN 7
IN 8 6
10 IN 9
IN 5
IN 10
IN 6
IN 12
12 IN 1 1
IN 7
COMMONS CONNECTED
INTERNALLY
15
16 IN 15
17
DC
COM
-DC
13
IN 13
14
IN 14
DC COM
-DC
7
11
DC COM
DC COM
COMMONS CONNECTED
INTERNALLY
SLC (decimal)
PLC (octal)
1746-IG16
1746-IH16
125V dc Sinking
TTL Input (Low = True)
+DC
+5 DC
1
0
IN 0
2
IN 2
3
IN 4
5
IN 6
7
IN 8
125V dc
10
11 IN 10
12
IN 11
13 IN 12
14
IN 13
15 IN 14
IN 15
16
17
DC COM
IN 9
IN 3
3
IN 4
6
IN 7
1
2
4
IN 5
4 IN 5
5
IN 6
6 IN 7
IN 8 6
10 IN 9
12 IN 1 1
IN 12
14
IN 14
-DC
DC
COM
PLC (octal)
13
IN 13
15
16 IN 15
17
DC COM
COMMONS CONNECTED
INTERNALLY
SLC (decimal)
7
11
IN 10
-DC
Publication CIG-WD001B-EN-P - May 2005
0 IN 1
IN 2
IN 3
+5V dc
+DC
IN 0
IN 1
SLC (decimal)
PLC (octal)
1746 I/O Modules
1746-IM16
1746-IM4
200/240V ac
200/240V ac
1746-IM8
200/240V ac
L1
NOT
USED
IN 0
0
IN 1
2
IN 3
1
IN 2
3
IN 4
4
IN 5
6
IN 7
10
IN 9
12
IN 1 1
14
IN 13
16
IN 15
L1
IN 1
NOT
USED
IN 2
L1
IN 3
200/240V ac
IN 0
IN 4
7
IN 8
IN 1
IN 5
11
IN 10
200/240V ac
IN 2
IN 6
13
IN 12
IN 3
IN 7
15
IN 14
L2
AC COM
L2
17
L2
IN 0
NOT
USED
NOT
USED
5
IN 6
200/240V ac
5-13
AC COM
COMMONS
CONNECTED
INTERNALLY
AC COM
COMMONS
CONNECTED
INTERNALLY
AC COM
AC COM
SLC (decimal)
PLC (octal)
1746-IN16
1746-INT4
24V ac/dc Sinking
Release Screw
CJC A+
L1 or +DC
CJC Assembly
IN 0
0
1
2
IN 3
4
IN 5
Channel 1+
3
IN 4
V ac/dc
Channel 0±
IN 1
IN 2
IN 6
Channel 0+
CJC A±
Do NOT
use these
connections
5
6 IN 7
7
IN 8
Channel 1±
Channel 2+
10 IN 9
Channel 2±
11
IN 10
12
IN 1 1
Channel 3+
13
IN 12
CJC B±
14 IN 13
IN 14
15
CJC Assembly
17
Release Screw
16 IN 15
AC/DC
COM
L2 or -DC
COMMONS
CONNECTED
INTERNALLY
AC/DC
COM
SLC (decimal)
Channel 3±
CJC B+
n/c
Do not connect
to this terminal
Cold Junction Compensation (CJC)
PLC (octal)
Do not remove or loosen the cold junction compensating thermistors
located on the terminal block. Both thermistors are critical to ensure accurate
thermocouple input readings at each channel. The module will not operate in the
thermocouple mode if a thermistor is removed.
Publication CIG-WD001B-EN-P - May 2005
5-14
1746 I/O Modules
1746-IO12
1746-IO12DC
24V dc INPUT - RELAY OUTPUT
100/120V ac INPUT - RELAY OUTPUT
L1 or +DC
L1 or +DC
VAC-VDC
VAC-VDC
OUT 0
OUT 0
OUT 1
V ac/dc
OUT 1
OUT 2
V ac/dc
OUT 3
OUT 4
OUT 5
CR
OUT 2
OUT 3
OUT 4
CR
CR
NOT
USED
OUT 5
CR
NOT
USED
L2 or -DC
L2 or -DC
+DC
L1
NOT
USED
NOT
USED
IN 0
IN 0
IN 1
IN 1
IN 2
IN 2
IN 3
100/120V ac
10-30V dc
IN 3
IN 4
IN 4
IN 5
IN 5
NOT
USED
L2
NOT
USED
NOT
USED
NOT
USED
AC COM
DC COM
-DC
1746-IO4
1746-IO8
1746-ITB16
100/120V ac Input - Relay Output
100/120V ac Input - Relay Output
24V dc Sinking
+DC
L1 or +DC
VAC-VDC
OUT 1
CR
L2 or -DC
OUT 2
OUT 3
L1
100/120V ac
L2
NOT
USED
NOT
USED
OUT 7
AC COM
1
4 IN 5
5
IN 6
CR
CR
24V dc
IN 8
L2 or -DC
6 IN 7
6
10 IN 9
12 IN 1 1
IN 0
14
IN 14
IN 2
IN 3
L2
OUT 7
AC COM
-DC
7
11
IN 10
IN 1
100/120V ac
IN 3
3
IN 4
IN 12
IN 1
0 IN 1
2
V ac/dc
OUT 1
NOT
USED
IN 0
IN 0
IN 2
OUT 0
NOT
USED
L1
L1 or +DC
VAC-VDC
V ac/dc
OUT 0
DC
COM
13
IN 13
15
16 IN 15
17
DC COM
COMMONS CONNECTED
INTERNALLY
SLC (decimal)
PLC (octal)
Publication CIG-WD001B-EN-P - May 2005
1746 I/O Modules
1746-ITV16
5-15
1746-IV16
24V dc Sourcing
24V dc Sourcing
-DC
-DC
IN 0
IN 2
0
IN 1
2
IN 3
4
IN 5
IN 6
6
IN 8
IN 10
+DC
24V dc
IN 8
IN 9
12
IN 1 1
14
IN 13
16 IN 15
IN 1
2
IN 3
4
IN 5
1
3
IN 6
IN 7
10
0
IN 4
5
7
IN 12
IN 14
IN 2
3
IN 4
24V dc
IN 0
1
11
IN 10
13
IN 12
15
IN 14
17
+DC
VDC
6
IN 7
10
IN 9
5
7
11
12
IN 1 1
14
IN 13
13
15
16 IN 15
17
VDC
VDC
VDC
VDC CONNECTED
INTERNALLY
VDC CONNECTED
INTERNALLY
SLC (decimal)
SLC (decimal)
PLC (octal)
PLC (octal)
1746-IV32
+V dc 1(1)
VDC 1
+V dc 1(1)
VDC 1
IN 0
dc Com 1
VDC 3
+V dc 3 (1)
VDC 3
+V dc 3(1)
IN 2
IN 18
IN 3
2
IN 19
IN 3
24V dc
3
3
IN 4
IN 20
IN 4
4
4
IN 5
IN 21
IN 5
5
5
IN 6
IN 22
IN 6
6
6
IN 7
IN 23
IN 7
7
7
IN 8
+DC
IN 24
10
10
IN 25
IN 9
IN 26
IN 10
12
12
IN 1 1
VDC
VDC CONNECTED
INTERNALLY
11
11
VDC
IN 27
13
13
IN 12
IN 28
14
14
IN 29
IN 13
15
15
IN 14
IN 30
16
16
IN 15
IN 31
17
Wire
Group 2
IN 1
1
1
2
+V dc 2 (1)
IN 0
IN 17
IN 2
+V dc 2 (1)
-DC
dc Com 3
0
0
dc Com 2
24V dc Sourcing
IN 16
IN 1
Connector
Key
1746-IV8
Wire
Group 3
Wire
Group 1
dc Com 4
17
VDC 2
VDC 4
VDC 2
VDC 4
+V dc 4 (1)
+V dc 4 (1)
Wire
Group 4
SLC (decimal)
PLC (octal)
(1)
The V dc pins on the 1746-IV32 input module are isolated between the four groups and the two V dc pins in each group are
connected internally. To maintain group isolation provided by 32-point I/O modules, use a 1492 terminal block that provides
group isolation. Consult 1492 documentation or your Allen-Bradley Sales Office for additional information.
Publication CIG-WD001B-EN-P - May 2005
5-16
1746 I/O Modules
1746-NI16I
(2)
Channel 0 2-Wire
Current Transmitter
+
-
+
IN 0
IN 1
IN 2
IN 3
Terminal Block Spare Part Catalog Number 1746-RT25G
(2)
+
Channel 2 2-Wire
Current Transmitter
Channel 4 2-Wire
Current Transmitter
Channel 6 3-Wire
Current Transmitter
Vdc power supply(5)
+
+
Channel 2
(2)
+
IN 4
IN 5
Channel 3
Channel 5
Channel 6
(2)
+
Channel 1
Channel 4
+
IN 6
Channel 7
IN 7
Analog Com
Analog Com
Channel 8
-
ANALOG ANALOG (1)
COM
COM
(1)
Channel 10
Channel 14
Channel 12
Channel 9
Channel 11
Channel 13
+
-
Optional second
FTC power supply(6)
Channel 0
IN 8
IN 9
(3)
IN 10
IN 11
(3)
IN 12
IN 13
(3)
IN 14
IN 15
+
-
Channel 15
Terminal Block Release Screw
Maximum Torque = 0.7 to 0.9 Nm (6 to 8 in-lbs.)
(3)
(4)
1.
2.
3.
4.
There are two common terminals for all of the 16 current inputs. These two analog common terminals are connected internally.
All shield wires should be connected to chassis mounting screws.
Unused channels should be connected to the analog common terminals (0 Volts).
If separate shielded cables are used for each analog input channel, interposing terminal blocks are needed to terminate up to 16 common wires. Then 1 to 4 common wires should be wired
from the interposing terminal block to the 2 common terminals on the 1746-NI16I module.
5. The module does not provide loop power for analog inputs. Use a power supply that matches the transmitter specifications.
6. More than one power supply can be used if all supplies are class 2.
Publication CIG-WD001B-EN-P - May 2005
1746 I/O Modules
5-17
1746-NI16V
(2)
Channel 0
Voltage Transmitter
Channel 2
Voltage Transmitter
+
+
–
Channel 6
Voltage Transmitter
Vdc power supply(5)
IN 1
+
+
IN 2
IN 3
IN 4
IN 5
Terminal Block Spare Part Catalog Number 1746-RT25G
–
Channel 0
(2)
Channel 4
Voltage Transmitter
IN 0
(2)
+
Channel 2
+
Channel 1
Channel 3
Channel 4
–
(2)
+
IN 6
Channel 5
IN 7
Channel 6
Channel 7
+
Analog Com
ANALOG ANALOG (1)
–
COM
COM
(1)
–
+
IN 8
IN 9
(3)
–
Analog Com
Channel 8
Channel 9
Channel 10
Channel 12
Channel 11
Channel 13
Channel 14
Channel 15
IN 10
Optional second
V dc power supply(6)
IN 11
(3)
+
Terminal Block Release Screw
Maximum Torque = 0.7 to 0.9 Nm (6 to 8 in-lbs.)
–
IN 12
IN 13
IN 14
IN 15
(3)
(3)
(4)
1.
2.
3.
4.
There are two common terminals for all of the 16 voltage inputs. These two analog common terminals are connected internally.
All shield wires should be connected to chassis mounting screws.
Unused channels should be connected to the analog common terminals (0 Volts).
If separate shielded cables are used for each analog input channel, interposing terminal blocks are needed to terminate up to 16 common wires. Then 1 to 4 common wires should be wired
from the interposing terminal block to the 2 common terminals on the 1746-NI16V module.
5. The module does not provide loop power for analog inputs. Use a power supply that matches the transmitter specifications.
6. More than one power supply can be used if all supplies are class 2.
1746-NI4
+
analog
source
+
earth
ground
analog
source
-
earth
ground
Jumper
unused
inputs.
0
1
2
3
4
5
6
7
8
9
10
11
IN 0+
IN 0ANL COM
IN 1+
IN 1ANL COM
IN 2+
IN 2ANL COM
IN 3+
IN 3ANL COM
Publication CIG-WD001B-EN-P - May 2005
5-18
1746 I/O Modules
1746-NI8
Terminal Block Spare Part Catalog Number 1746-RT25G
shield
Power
+
Supply
Connections –
single-end
signal source
+
+
+
+
shield
+
+
shield
–
+
–
+
–
Channel 2
Channel 3 (+)
Channel 3 (-)
Channel 4 (+)
Channel 3
Channel 5 (+)
Channel 5 (-)
–
Channel 6 (+)
Channel 6 (-)
+
+
differential
signal source –
Channel 4
–
shield
+
Channel 7 (+)
Channel 7 (-)
Shield
Channel 5
Terminal Block Release Screw
Maximum Torque=0.7 to 0.9 Nm
(6 to 8 in-lbs.)
–
shield
+
+
differential
signal source –
Channel 6
–
shield
+
Channel 2 (+)
Channel 4 (-)
+
+
differential
signal source –
Channel 1 (-)
–
shield
–
Channel 1 (+)
Channel 1
Channel 2 (-)
single-end
signal source
+
Channel 0 (+)
–
+
+
Shield
Channel 0 (-)
single-end
signal source
single-end
signal source
Channel 0
–
shield
+
differential
signal source –
Channel 7
–
shield
shield
1. Use unshielded communication cable (Belden 8761) and keep the length as short as possible.
2. Connect only one end of the cable shield to earth ground.
3. Connect the shield drain wires for channels 0 to 3 to the top shield terminal.
4. Connect the shield drain wires for channels 4 to 7 to the bottom shield terminal.
5. Shield terminals are internally connected to chassis ground which is connected to earth
ground via the SLC backplane.
6. Single-ended source commons may be jumpered together at the terminal block.
7. The channels are not isolated from each other.
8. If a differential signal source has an analog common, it cannot and must not be
connected to the module.
9. The common mode voltage range is ±10.5 volts. The voltage between any two terminals
must be less than 15 volts when connected in a single-ended configuration.
10. The module does not provide power for the analog inputs.
11. Use a power supply that matches the transmitter (sensor) specifications.
1746-NIO4I
1746-NIO4V
+
+
analog
source
-
earth
ground
Jumper
unused
inputs.
LOAD
earth
ground
Do not jumper
unused outputs.
Publication CIG-WD001B-EN-P - May 2005
0
1
2
3
4
5
6
7
8
9
10
11
IN 0+
IN 0ANL COM
analog
source
-
IN 1+
IN 1ANL COM
not used
OUT 0
ANL COM
not used
OUT 1
ANL COM
earth
ground
Jumper
unused
inputs.
LOAD
earth
ground
Do not jumper
unused outputs.
0
1
2
3
4
5
6
7
8
9
10
11
IN 0+
IN 0ANL COM
IN 1+
IN 1ANL COM
not used
OUT 0
ANL COM
not used
OUT 1
ANL COM
1746 I/O Modules
1746-NO4I
24V dc power supply if external power is
selected. Cable length from external 24V dc
power supply to analog module must be less
than 10m.
1746-NO4V
Ext. pwr
sup.
LOAD
earth
ground
LOAD
Analog commons are internally connected
in the module. Channels are not isolated
from each other.
earth
ground
Do not jumper
unused outputs.
0
1
+24V dc
dc COM
0
1
2
3
4
5
6
7
OUT 0
ANL COM
24V dc power supply if external power is
selected. Cable length from external 24V dc
power supply to analog module must be less
than 10m.
earth
ground
OUT 1
ANL COM
OUT 2
ANL COM
OUT 3
ANL COM
I Out 2
I Out 3
I Out 4
I Out 5
I Out 6
I Out 7
+24 VDC
ANL COM 0
ANL COM 1
ANL COM 2
ANL COM 3
ANL COM 4
ANL COM 5
ANL COM 6
ANL COM 7
DC COM
Ext. pwr
sup.
LOAD
LOAD
Analog commons are internally connected
in the module. Channels are not isolated
from each other.
1746-NO8I
I Out 0
I Out 1
earth
ground
Do not jumper
unused outputs.
0
1
+24V dc
dc COM
0
1
2
3
4
5
6
7
OUT 0
ANL COM
V Out 0
V Out 1
OUT 2
ANL COM
OUT 3
ANL COM
V Out 2
V Out 3
V Out 4
V Out 5
V Out 6
V Out 7
+24 VDC
ANL COM 0
ANL COM 1
ANL COM 2
ANL COM 3
ANL COM 4
ANL COM 5
ANL COM 6
ANL COM 7
DC COM
Terminal Block Release Screw
Maximum Torque = 0.7 to 0.9 Nm (6 to 8 in-lbs.)
Terminal Block Spare Part Catalog Number 1746-RT25G
Terminal Block Spare Part Catalog Number 1746-RT25G
Disconnect power to the SLC before
attempting to install, remove, or wire
the removable terminal block. To avoid
cracking the removable terminal block,
alternate the removal of the slotted
terminal block release screws.
Disconnect power to the SLC before
attempting to install, remove, or wire
the removable terminal block. To avoid
cracking the removable terminal block,
alternate the removal of the slotted
terminal block release screws.
Channels are not isolated from each
other. All analog commons (ANL COM)
are connected together internally.
OUT 1
ANL COM
1746-NO8V
Terminal Block Release Screw
Maximum Torque = 0.7 to 0.9 Nm (6 to 8 in-lbs.)
IMPORTANT
5-19
IMPORTANT
Channels are not isolated from each
other. All analog commons (ANL COM)
are connected together internally.
Publication CIG-WD001B-EN-P - May 2005
5-20
1746 I/O Modules
1746-NR4
Terminal Connections
Release Screw Max Torque =
0.7 - 0.9 Nm (6 - 8 in-lbs)
Shield
Shield
Channel 0 RTD
Channel 1 RTD
Channel 0 Sense
Channel 1 Sense
Channel 0 Return
Channel 1 Return
Shield
Shield
Channel 2 RTD
Channel 3 RTD
Channel 2 Sense
Channel 3 Sense
Channel 2 Return
Channel 3 Return
Shield
Shield
Release Screw Max Torque
= 0.7 - 0.9 Nm (6 - 8 in-lbs)
2-Wire RTD
Add Jumper
3-Wire RTD
Cable Shield
Shield
Shield
CH 0 RTD
Belden #9501 or #9533
Shielded Cable
Shield
RTD
RTD
CH 0 RTD
CH 0 Sense
CH 0 Return
4-Wire RTD
Cable Shield
Cable Shield
RTD
RTD
CH 0 RTD
Sense
Sense
CH 0 Sense
Return
CH 0 Return
RTD
RTD
Sense
Sense
CH 0 Sense
Return
Return
Return
CH 0 Return
Belden #9501 Shielded Cable
2-Wire Potentiometer
Cable Shield
Add Jumper
Run RTD and sense wires from module to
potentiometer terminal and tie them to one point.
Potentiometer
Shield
Shield
RTD
CH 0 RTD
CH 0 Sense
CH 0 Sense
CH 0 Return
Return
RTD
Sense
Potentiometer
Return
CH 0 Return
Belden #9501 Shielded Cable
Belden #9501 or #9533 Shielded Cable
Potentiometer wiper arm can be connected to either the RTD or Return terminal,
depending on whether you want increasing or decreasing resistance.
Publication CIG-WD001B-EN-P - May 2005
Return
Leave one sensor wire open.
3-Wire Potentiometer
Cable Shield
CH 0 RTD
Return
Belden #9501 or #9533 Shielded Cable
1746 I/O Modules
5-21
1746-NR8
Terminal Connections
2-Wire RTD
Cable Shield
(Frame Ground)
2-Wire Potentiometer
Add
Jumper
RTD 0
Sense 0
Return 0
RTD 1
Sense 1
Return 1
RTD 2
Sense 2
Return2
RTD
RTD 0
Sense 0
Return 0
RTD 1
Sense 1
Return 1
RTD 2
Sense 2
Return2
RTD 3
Sense 3
Return 3
RTD 4
Sense 4
Return 4
RTD 5
Sense 5
Return 5
RTD 6
Sense 6
Return 6
RTD 7
Sense 7
Return 7
Return
Belden #9501 Shielded Cable
3-Wire RTD
Cable Shield
(Frame Ground)
RTD 0
Sense 0
Return 0
RTD 1
Sense 1
Return 1
RTD 2
Sense 2
Return2
RTD
Sense
Return
Belden #9501 Shielded Cable or
Belden #83503 Shielded Cable
4-Wire RTD
Cable Shield
(Frame Ground)
RTD 0
Sense 0
Return 0
RTD 1
Sense 1
Return 1
RTD 2
Sense 2
Return 2
RTD 3
Sense 3
Return 3
RTD 4
Sense 4
Return 4
RTD 5
Sense 5
Return 5
RTD 6
Sense 6
Return 6
RTD 7
Sense 7
Return 7
Add Jumper
Potentiometer
Cable Shield
(Frame Ground)
Belden #9501 Shielded Cable
RTD 0
Sense 0
Return 0
RTD 1
Sense 1
Return 1
RTD 2
Sense 2
Return2
RTD
Sense
Return
Leave One Sensor Wire Open
Belden #9501 Shielded Cable or
Belden #83503 Shielded Cable
1746-NT4
CJC A+
CJC Assembly
1746-NT8
Release Screw Max. Torque =
0.7 to 0.9 Nm (6 to 8 in-lb)
Channel 0+
CJC A-
CJC A+
Thermocouple or mV Cable
CJC AChannel 0+
Channel 0Shield for CH0 and CH1
Channel 1+
Channel 1-
Channel 0-
Shield
Channel 1+
Shield
Channel 1-
Channel 2+
Channel 2-
Channel 2+
Shield for CH2 and CH3
Channel 3+
Channel 2-
Channel 3Channel 4+
Channel 3+
Channel 4Shield for CH4 and CH5
Channel 3-
Channel 5+
Channel 5-
Shield
Shield
Shield
CJC B+
CJC Assembly
CJC B-
Analog Common
(1)
Channel 6+
Channel 6-
Release Screw Max. Torque =
0.7 to 0.9 Nm (6 to 8 in-lb)
Shield for CH6 and CH7
Channel 7+
Channel 7CJC B+
Cold Junction Compensation (CJC)
CJC B-
Do not remove or loosen the cold junction compensating thermistor
assemblies located between the two upper and lower CJC terminals on
the terminal block. Both thermistor assemblies are critical to ensure
accurate thermocouple input readings at each channel. The module will
not operate in the thermocouple mode if either assembly is removed.
TB1
Publication CIG-WD001B-EN-P - May 2005
5-22
1746 I/O Modules
1746-OA8
1746-OA16
100 to 240V ac Triac Output
100 to 240V ac Triac Output
L1
VAC 1
100-240V ac
5 OUT 6
CR
6
OUT 7
CR
OUT 3
CR
CR
4
CR
CR
OUT 2
1
2
OUT 5
100-240V ac
CR
OUT 3
11
OUT 8
13
OUT 10
100-240V ac
15
OUT 12
14
OUT 15
CR
CR
OUT 6
17 OUT 14
16
CR
OUT 7
L2
CR
NOT
USED
L2
L2
100-240V ac
12
OUT 13
CR
2
4
10
OUT 1 1
OUT 4
OUT 5
L1
VAC 2
OUT 9
L1
VAC 2
0
5 OUT 4
NOT
USED
7
L2
OUT 0
3 OUT 2
OUT 5
L2
CR
VAC 1
OUT 1
1 OUT 2
3 OUT 4
COMMONS
CONNECTED
INTERNALLY
VAC 1
L1
0
OUT 3
100-240V ac
OUT 0
OUT 1
100 to 240V ac High Current Triac Output
OUT0
OUT 1
L1
VA C 1
1746-OAP12
OUT 7
CR
7 OUT 6
OUT 9
CR
6
11 OUT 8
CR
OUT 1 1
L2
SLC (decimal)
CR
100-240V ac
10
13 OUT 10
12
VAC 2
PLC (octal)
CR
L1
VA C 2
1
COMMONS
CONNECTED
INTERNALLY
SLC (decimal)
PLC (octal)
1. This module provides fused commons for short circuit protection.
1746-OB16
1746-OB16E
Transistor Output-Sourcing
+DC
VDC
CR
1
OUT 2
3
OUT 4
5
OUT 6
7
OUT 8
11
OUT 10
13
OUT 12
15
OUT 14
10-30V dc
OUT 4
5
OUT 6
7
OUT 8
11
OUT 10
13
OUT 12
15
OUT 14
2
4
6
10
CR
CR
CR
14
OUT 13
16
OUT 15
CR
17
CR
12
OUT 1 1
DC COM
CR
CR
17
DC COM
-DC
-DC
SLC (decimal)
PLC (octal)
Publication CIG-WD001B-EN-P - May 2005
3
OUT 7
OUT 9
CR
16
OUT 15
OUT 2
OUT 5
CR
14
OUT 13
CR
CR
CR
12
OUT 1 1
CR
CR
6
10
0
1
OUT 3
4
OUT 7
OUT 0
OUT 1
2
OUT 5
OUT 9
VDC
0
OUT 3
10-50V dc
+DC
OUT 0
OUT 1
CR
Transistor Output-Sourcing (electronically protected)
SLC (decimal)
PLC (octal)
1746 I/O Modules
1746-OB32
1746-OB32E
5 to 50V dc Transistor Output Sourcing
10 to 30V dc Electronically Protected Sourcing
Wire
Group 2
Wire
Group 1
VDC 1
VDC 2
+V dc 2(2)(3)
+V dc 1
+V dc 1 (2)(3)
VDC 1
VDC 2
+V dc 2(2)(3)
+V dc 1 (2)(3)
0
1
2
2
CR
2
CR
10
OUT 13
CR
OUT 28
14
OUT 13
15
OUT 29
OUT 14
16
16
15
OUT 30
16
16
OUT 31
OUT 15
17
17
14
15
OUT 30
dc Com 1(2)
COM 1
COM 2
dc Com 2(2)
dc Com 1(2)
COM 1
COM 2
dc Com 2(2)
OUT 31
17
17
dc Com 1(2)
dc Com 1
(2)
CR
13
13
OUT 29
OUT 15
CR
12
12
OUT 1 1 OUT 27
14
15
CR
11
OUT 26
OUT 10
OUT 12
14
OUT 14
OUT 25
11
CR
CR
10
10
OUT 28
OUT 12
OUT 24
OUT 8
OUT 9
CR
13
7
7
CR
CR
12
12
OUT 1 1 OUT 27
13
6
OUT 23
OUT 7
CR
CR
11
OUT 26
OUT 10
OUT 22
6
OUT 25
11
5
5
OUT 24
10
OUT 9
CR
4
OUT 21
OUT 5
OUT 6
Connector
Key
CR
OUT 20
4
7
7
2
3
3
6
CR
OUT 19
OUT 3
CR
OUT 23
CR
1
OUT 18
OUT 2
CR
5
6
CR
1
OUT 22
0
OUT 17
CR
OUT 21
OUT 8
OUT 16
0
4
5
OUT 7
+V dc 2(2)(3)
OUT 4
4
OUT 5
+V dc 2(2)(3)
VDC 2
OUT 1
OUT 20
OUT 6
VDC 2
VDC 1
OUT 0
CR
3
3
OUT 4
CR
1
VDC 1
CR
OUT 19
OUT 3
CR
CR
CR
CR
OUT 18
OUT 2
CR
CR
0
OUT 17
OUT 1
Connector
Key
(2)(3)
OUT 16
OUT 0
CR
Wire
Group 2
Wire
Group 1
+V dc 1(2)(3)
CR
5-23
COM 1
COM 2
dc Com 2(2)
COM 1
COM 2
dc Com 2(2)
SLC (decimal)
SLC (decimal)
PLC (octal)
PLC (octal)
1. The V dc and dc Com pins on the 1746-OB32 and 1746-OB32E output module are isolated
between the two groups and the two V dc and two dc Com pins in each group are connected internally.
1. The V dc and dc Com pins on the 1746-OB32 and 1746-OB32E output module are isolated
between the two groups and the two V dc and two dc Com pins in each group are connected internally.
2. Both V dc pins must be connected to the dc power source if current for a common group
is expected to exceed 2 amps. To maintain group isolation provided by 32-point I/O modules,
use a 1492 terminal block that provides group isolation.
2. Both V dc pins must be connected to the dc power source if current for a common group
is expected to exceed 2 amps. To maintain group isolation provided by 32-point I/O modules,
use a 1492 terminal block that provides group isolation.
1746-OB6EI
1746-OB8
10 to 50V dc Transistor Output-Sourcing
10 to 30V dc Transistor Output-Sourcing
Channel-to-Channel Isolated (electronically protected)
VDC 0
10-30V dc
CR
+DC
VDC 3
10-30V dc
CR
DC
COM 3
+DC
VDC 5
CR
10-30V dc
OUT 1
DC
COM 0
-DC
VDC 2
+DC
OUT 2
OUT 3
OUT 3
-DC
10-30V dc
OUT 0
OUT 0
DC
COM 1
OUT 2
10-30V dc
DC
COM 2
-DC
VDC 4
+DC
OUT 5
DC
COM 5
+DC
+DC
OUT 1
-DC
-DC
VDC
VDC 1
+DC
OUT 4
DC
COM 4
10-30V dc
-DC
10-50V dc
OUT 4
CR
OUT 5
CR
OUT 6
OUT 7
DC
COM
CR
CR
-DC
Publication CIG-WD001B-EN-P - May 2005
5-24
1746 I/O Modules
1746-OBP16
1746-OBP8
20.4 to 26.4V dc Transistor Output-Sourcing
Transistor Output-Sourcing 1
+DC
VDC
1
OUT 2
3
OUT 4
5
OUT 6
7
OUT 8
11
OUT 10
13
OUT 12
15
OUT 14
CR
OUT 3
20.4-26.4V dc
DC
COM1
NC
NC
NC
CR
-DC
CR
12
OUT 1 1
14
OUT 13
CR
OUT 1
6
10
OUT 9
CR
OUT 2
4
OUT 7
20.4-26.4V dc
OUT 0
2
OUT 5
CR
VDC1
0
OUT 3
CR
+DC
OUT 0
OUT 1
16
OUT 15
CR
NC
CR
NC
NC
CR
+DC
VDC2
17
OUT 4
DC COM
CR
OUT 5
CR
OUT 7
OUT 6
20.4-26.4V dc
-DC
SLC (decimal)
DC
COM2
-DC
PLC (octal)
1. This module provides fused commons for short circuit protection.
1746-OG16
1746-OV16
TTL Output (Low = True)
10 to 50V dc OR 20.4 to 26.4V dc Transistor
Output Sinking
+DC
+DC
VDC
L
1
OUT 3
L
OUT 5
L
OUT 7
2
OUT 4
L
L
L
L
OUT 8
CR
12
5
OUT 6
7
OUT 8
11
OUT 10
2
4
L
14
16
L
CR
17
DC COM
-DC
CR
12
13
OUT 12
15
OUT 14
14
OUT 13
CR
L
6
10
OUT 1 1
15 OUT 14
-DC
OUT 4
OUT 9
OUT 12
OUT 15
3
OUT 5
10
13
OUT 2
OUT 7
CR
L
11 OUT 10
OUT 1 1
OUT 13
10-50V dc (OV16)
20.4-26.5V dc (OVP16)
L
6
7
OUT 9
OUT 6
1
OUT 3
L
4
5
0
OUT 1
L
OUT 2
3
+5V dc
OUT 0
0
OUT 1
L
VDC
L
OUT 0
OUT 15
17
16
CR
CR
CR
DC COM
SLC (decimal)
PLC (octal)
SLC (decimal)
PLC (octal)
Publication CIG-WD001B-EN-P - May 2005
1746 I/O Modules
1746-OV8
1746-OV32
5 to 50V dc Transistor Output Sinking
+V dc 1(2)
VDC 1
VDC 2
+V dc 2(2)
VDC
VDC 1
VDC 2
+V dc 2(2)
OUT 0
1
OUT 19
3
CR
5
OUT 5
CR
6
OUT 6
OUT 21
5
OUT 22
OUT 6
6
OUT 23
OUT 7
OUT 24
OUT 25
11
OUT 10
11
OUT 27
13
OUT 12
-DC
CR
12
12
OUT 1 1
CR
DC COM
CR
OUT 26
CR
OUT 7
CR
10
10
OUT 9
CR
7
7
OUT 8
CR
CR
13
OUT 28
14
OUT 13
14
OUT 29
15
15
OUT 14
OUT 30
16
16
OUT 31
OUT 15
17
17
dc Com 1
10-50V dc
OUT 4
4
4
(2)(3)
OUT 3
CR
3
OUT 20
OUT 5
dc Com 1
OUT 2
CR
2
2
OUT 3
OUT 4
(2)(3)
CR
1
OUT 18
OUT 2
CR
CR
OUT 1
OUT 17
OUT 1
CR
CR
CR
0
0
Connector
Key
+DC
OUT 16
OUT 0
CR
CR
10 to 50V dc Transistor
Output Sinking
Wire
Group 2
Wire
Group 1
+V dc 1 (2)
5-25
COM 1
COM 2
dc Com 2(2)(3)
COM 1
COM 2
dc Com 2(2)(3)
1. The V dc and dc Com pins on the 1746-OV32 output module are isolated between the two groups.
Also, the two V dc and two V Com pins in each group are connected internally.
2. Both dc Com pins must be connected to the dc power source if current for a common group is expected
to exceed 2 amps. To maintain group isolation provided by 32-point I/O modules, use a 1492 terminal
block that provides group isolation.
1746-OVP16
1746-OW16
Relay Output
10 to 50V dc OR 20.4 to 26.4V dc Transistor 1
Output Sinking
L1 or +DC
VAC-VDC
1
OUT 1
+DC
OUT 0
0
1
20.4-26.5V dc
CR
3
OUT 4
5
OUT 6
7
OUT 8
11
OUT 12
15
OUT 14
14
OUT 13
CR
-DC
L2 or -DC
CR
12
13
OUT 15
17
16
6
OUT 7
6
OUT 10
OUT 1 1
4
5 OUT 6
CR
10
OUT 9
CR
CR
4
OUT 7
CR
3 OUT 4
OUT 5
2
OUT 5
2
OUT 3
V ac/dc
OUT 2
OUT 3
0
1 OUT 2
VDC
OUT 1
OUT0
CR
CR
7
VAC-VDC
2
11 OUT 8
10
OUT 1 1
OUT 10
13
OUT 13
12
15 OUT 12
OUT 15
14
17 OUT 14
16
L1 or +DC
OUT 9
CR
CR
CR
CR
CR
DC COM
V ac/dc
CR
CR
L2 or -DC
1. This module provides fused commons for short circuit protection.
Publication CIG-WD001B-EN-P - May 2005
5-26
1746 I/O Modules
1746-OW4
1746-OW8
Relay Output
1746-OX8
Channel-to-Channel Isolated Relay Output
Relay Output
L1 or +DC
VAC-VDC
1
L1 or +DC
VAC-VDC
OUT 0
OUT 0
V ac/dc
OUT 1
V ac/dc
OUT 1
CR
OUT 2
L2 or -DC
CR
OUT 3
CR
OUT 2
NOT
USED
VAC-VDC
2
NOT
USED
OUT 4
NOT
USED
VS1 L1
VAC-VDC
1
VS2 VDC
VAC-VDC
2
VS3 VDC
VAC±VDC
3
NOT USED
L1 or +DC
VS4 L1
VAC-VDC
4
VS5 L1
VAC-VDC
5
OUT 0
V ac/dc
OUT 6
CR
OUT 7
CR
L2 or -DC
VS6 VDC
VAC-VDC
6
VS7 VDC
VAC-VDC
7
(+)
9
7
(+) (±)
5 3
10
8 6
(±)
(±)
Drive Output
OUT 2
VS2 DC COM
OUT 3
VS3 DC COM
CR
VS4 L2
OUT 5
VS5 L2
OUT 6
VS6 DC COM
OUT 7
CR
VS7 DC COM
+Gate
15V
Power Supply
Axis Loop 2
Axis Loop 3
Axis Loop 4
+Ret ±Ret +Out Out +Ret ±Ret +Out Out +Ret ±Ret +Out Out
2
2
2 Com 3
3
3
Com 4
4
4 Com
4
8
12
(± ) (C) (+)
2
4
(+)
CR
NOT
USED
1746-QV
_
+
Axis Loop 1
+Ret ±Ret +Out Out
1
1
1 Com
0
1
2
3
1
VS0 L2
VS1 L2
1746-QS Typical Connections to IFM Terminal Block
T emposonics II,
RPM or DPM
CR
OUT 1
OUT 4
OUT 5
NOT
USED
OUT
NOT7
USED
VAC-VDC
0
L2 or -DC
CR
OUT 3
VS0 L1
Linear
Displacement
Transducer
-Gate
-Interr
+Interr
Sh/Frame
+Int ±Int
1
1
16
17
±V
1F
34
SH
SH
18
19
LDT +V
Com 1F
35
36
+Int ±Int
2
2
20
SH
±V LDT +V
2F Com 2F
38
SH
+Int ±Int SH
3
3
24
±V
LDT
3F Com
42
+V
3F
SH
+Int ±Int
4
4
28
SH SH
±V LDT +V
4F Com 4F
46
±V
32
+V
-15V dc
33
PS
Earth
Com GND
50 51
Comm
+
+15V dc
+
+Analog
-Analog
Internal Connections:
±V (32) is connected to (34) (38) (42) (46) through fuses that you provide
+V (33) is connected to (36) (40) (44) (48) through fuses that you provide
PS Com (50) is connected to all LDT Com (35) (39) (43) (47)
Earth GND (51) is connected to all SH (18) (19) (22) (23) (26) (27) (30)(31)
Publication CIG-WD001B-EN-P - May 2005
Valve
Amplifier
Chapter
6
1747 I/O on Fixed Hardware Controllers
1747-L20A
(Hi)
L1
(Lo)
L2
5-265 V AC or
5-125 VDC 1
1747-L20B
(Hi)
L1
1
CR
CR
(Hi)
L1
(Lo)
L2
5-265 V AC or
5-125 VDC
85-265 V AC
CR
(Lo)
L2
(Lo)
L2
(Hi)
L1
85-132 V AC
CHASSIS
GND
NOT
USED
NOT
USED
AC
COM
AC
COM
IN 0
IN 1
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
Commons
Connected
Internally
The outputs are isolated in groups as shown. Therefore, different voltages can be
applied to each group as the specific application requires.
1
(Lo)
L2
1
CR
CR
CR
VAC 1 OUT 0 OUT 1 OUT 2 OUT 3 VAC 2 OUT 4 OUT 5 OUT 6 OUT 7
(Hi)
L1
(Lo)
L2
(Lo)
L2
(Hi)
L1
85-132 V AC
85-265
VAC
85-265
VAC
120/240 VAC
VAC
NEUT
85-265 V AC
CR
VAC
OUT 0 OUT 1 OUT 2 OUT 3 VAC
OUT 4 OUT 5 OUT 6 OUT 7
VDC 1
VDC 2
(Hi)
L1
1
CR
(Hi)
L1
(Lo)
L2
120/240 VAC
VAC
NEUT
CHASSIS
GND
NOT
USED
NOT
USED
AC
COM
AC
COM
IN 0
IN 1
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
Commons
Connected
Internally
The outputs are isolated in groups as shown. Therefore, different voltages can be
applied to each group as the specific application requires
Publication CIG-WD001B-EN-P - May 2005
6-2
1747 I/O on Fixed Hardware Controllers
1747-L20C
(Hi)
L1
5-265 V AC
5-125 VDC
1747-L20F
(Hi)
L1
(Lo)
L2
1
5-265 V AC
5-125 VDC
1
CR
(Hi)
L1
(Lo)
L2
CR
CR
5-265 V AC or
5-125 VDC 1
(Hi)
L1
CR
(Lo)
L2
5-265 V AC or
5-125 VDC
1
CR
CR
CR
CR
VAC
OUT 0 OUT 1 OUT 2 OUT 3 VAC
OUT 4 OUT 5 OUT 6 OUT 7
VDC 1
VDC 2
VAC
OUT 0 OUT 1 OUT 2 OUT 3 VAC
OUT 4 OUT 5 OUT 6 OUT 7
VDC 1
VDC 2
(Hi)
L1
(Lo)
L2
(Lo)
L2
- DC
+ DC
10-30
VDC
+
-
85-265
VAC
Sourcing
Device
120/240 VAC
VAC
NEUT
CHASSIS
GND
PWR OUT DC
+24VDC 2 COM
PWR OUT DC
COM 2
COM
IN 1
IN 0
HSC
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
24 VDC
+10%
IN 11
+ 24
VDC
IN 10
VDC
NEUT
CHASSIS
GND
Commons
Connected
Internally
- DC
10-30
VDC
NOT
USED
NOT
USED
DC
COM
DC
COM
IN 1
IN 0
HSC
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
Sourcing
Device
Commons
Connected
Internally
+ DC
1. The outputs are isolated in groups as shown. Therefore, different voltages can
be applied to each group as the specific application requires.
The outputs are isolated in groups as shown. Therefore, different voltages can be applied to each
group as the specific application requires.
2. 24V dc, 200mA user power is available for sensors.
1747-L30A
(Hi)
L1
5-265 V AC
5-125 VDC
(Lo) (Hi)
L2 L1 5-265 V AC
5-125 VDC
1
CR
1
CR
(Hi)
L1
(Lo)
L2
CR
(Lo)
L2
NOT
USED
(Hi)
L1
(Lo)
L2
1
CR
VAC
OUT 0 OUT 1 OUT 2 OUT 3 VAC
OUT 4 OUT 5 NOT
VDC 1
VDC 2
USED
(Hi)
L1
5-265 V AC
5-125 VDC
1
5-265 V AC
5-125 VDC
CR
(Lo)
L2
CR
VAC
OUT 6 OUT 7 OUT 8 OUT 9
VDC 3
VAC
OUT 10 OUT 1 1 NOT
VDC 4
USED
(Lo)
L2
(Hi)
L1
85 - 132 V AC
85-265
VAC
120/240 VAC
NEUT
VAC
CHASSIS
GND
NOT
USED
NOT
USED
AC
COM
AC
COM
AC
COM
AC
COM
IN 0
IN 1
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
IN 13
IN 12
IN 15
IN 14
IN 17
IN 16
NOT
USED
NOT
USED
NOT
USED
NOT
USED
NOT
USED
NOT
USED
Commons
Connected
Internally
These outputs are isolated in groups as shown. Therefore, different voltages can be applied to each group as the specific application requires.
Publication CIG-WD001B-EN-P - May 2005
NOT
USED
1747 I/O on Fixed Hardware Controllers
6-3
1747-L30B
(Hi)
L1
(Hi)
L1
(Lo)
L2
85-265 V AC
(Lo)
L2
85-265 V AC
1
CR
CR
CR
VAC 1 VAC 1 OUT 0 OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 NOT
USED
NOT
USED
1
CR
CR
VAC 2 VAC 2 OUT 6 OUT 7 OUT 8
VAC 1
Connected
Internally
OUT 9
CR
OUT 10 OUT 1 1 NOT
USED
NOT
USED
VAC 2
Connected
Internally
(Hi)
L1
(Lo)
L2
(Lo)
L2
(Hi)
L1
85-132 V AC
85 - 265
VAC
120/240 VAC
NEUT
VAC
CHASSIS
GND
NOT
USED
NOT
USED
AC
COM
AC
COM
AC
COM
AC
COM
IN 1
IN 0
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
IN 13
IN 12
IN 15
IN 14
IN 17
IN 16
NOT
USED
NOT
USED
NOT
USED
NOT
USED
NOT
USED
NOT
USED
Commons
Connected
Internally
These outputs are isolated in groups as shown. Therefore, different voltages can be applied to each group as the specific application requires.
1747-L30C
(Hi)
L1
5-265 V AC
5-125 VDC
(Lo) (Hi)
L2 L1 5-265 V AC
5-125 VDC
1
CR
1
CR
(Lo)
L2
(Hi)
L1
CR
VAC
OUT 0 OUT 1 OUT 2 OUT 3 VAC
OUT 4 OUT 5 NOT
VDC 1
VDC 2
USED
(Hi)
L1
5-265 V AC
5-125 VDC
NOT
USED
1
(Lo)
L2
CR
CR
(Hi)
L1 5-265 V AC
5-125 VDC
1
(Lo)
L2
CR
VAC
OUT 6 OUT 7 OUT 8 OUT 9
VDC 3
VAC
OUT 10 OUT 1 1 NOT
VDC 4
USED
NOT
USED
(Lo)
L2
85-265
VAC
Sourcing
Device
120/240 VAC
NEUT
VAC
CHASSIS
GND
PWR OUT DC
+24VDC 2 COM
PWR OUT DC
COM 2 COM
DC
COM
DC
COM
IN 1
IN 0
HSC
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
IN 13
IN 12
IN 15
IN 14
IN 17
IN 16
NOT
USED
NOT
USED
NOT
USED
NOT
USED
NOT
USED
NOT
USED
Commons
Connected
Internally
- DC
10-30
VDC
+ DC
1. The outputs are isolated in groups as shown. Therefore, different voltages can be applied to each group as the specific application requires.
2. 24 VDC, 200mA user power is available for sensors.
Publication CIG-WD001B-EN-P - May 2005
6-4
1747 I/O on Fixed Hardware Controllers
1747-L40A
(Hi)
L1
5-265 V AC
5-125 VDC
(Hi)
L1
(Lo)
L2
1
1
CR
(Hi)
L1
(Lo)
L2
5-265 V AC
5-125 VDC
CR
CR
5-265 V AC
5-125 VDC
(Hi)
L1
(Lo)
L2
CR
CR
(Lo)
L2
5-265 V AC
5-125 VDC
1
1
CR
CR
CR
VAC
OUT 0 OUT 1 OUT 2 OUT 3 VAC
OUT 4 OUT 5 OUT 6 OUT 7 VAC
OUT 8 OUT 9 OUT 10 OUT 1 1 VAC
OUT 12 OUT 13 OUT 14 OUT 15
VDC 1
VDC 2
VDC 3
VDC 4
(Hi)
L1
(Lo)
L2
(Lo)
L2
(Hi)
L1
85-132 V AC
85-265
VAC
120/240 VAC
VAC
NEUT
CHASSIS
GND
NOT
USED
NOT
USED
AC
COM
AC
COM
AC
COM
AC
COM
IN 1
IN 0
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
IN 13
IN 12
IN 15
IN 14
IN 17
IN 16
IN 19
IN 18
IN 21
IN 20
IN 23
IN 22
Commons
Connected
Internally
The outputs are isolated in groups as shown. Therefore, different voltages can be applied to each group as the specific application requires.
1747-L40B
(Hi)
L1
85-265 V AC
CR
(Hi)
L1
(Lo)
L2
1
85-265 V AC
CR
CR
CR
CR
(Lo)
L2
1
CR
CR
CR
VAC 1 VAC 1 OUT 0 OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 OUT 7 VAC 2 VAC 2 OUT 8 OUT 9 OUT 10 OUT 1 1 OUT 12 OUT 13 OUT 14 OUT 15
VAC 1
Connected
Internally
VAC 2
Connected
Internally
(Hi)
L1
(Lo)
L2
(Lo)
L2
(Hi)
L1
85-132 V AC
85-265
VAC
120/240 VAC
VAC
NEUT
CHASSIS
GND
NOT
USED
NOT
USED
AC
COM
AC
COM
AC
COM
AC
COM
IN 0
IN 1
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
IN 13
IN 12
IN 15
IN 14
IN 17
IN 16
IN 19
IN 18
IN 21
IN 20
IN 23
IN 22
Commons
Connected
Internally
The outputs are isolated in groups as shown. Therefore, different voltages can be applied to each group as the specific application requires.
Publication CIG-WD001B-EN-P - May 2005
1747 I/O on Fixed Hardware Controllers
6-5
1747-L40C
(Hi)
L1
5-265 V AC
5-125 VDC
(Hi)
L1
(Lo)
L2
1
1
CR
(Hi)
L1
(Lo)
L2
5-265 V AC
5-125 VDC
CR
CR
(Hi)
L1
(Lo)
L2
5-265 V AC
5-125 VDC
5-265 V AC
5-125 VDC
1
CR
CR
CR
(Lo)
L2
1
CR
CR
VAC
OUT 0 OUT 1 OUT 2 OUT 3 VAC
OUT 4 OUT 5 OUT 6 OUT 7 VAC
OUT 8 OUT 9 OUT 10 OUT 1 1 VAC
OUT 12 OUT 13 OUT 14 OUT 15
VDC 1
VDC 2
VDC 3
VDC 4
Sourcing Device
(Hi)
L1
(Lo)
L2
85-265
VAC
120/240 VAC
VAC
NEUT
CHASSIS
GND
PWR OUT DC
+24VDC 2 COM
PWR OUT DC
COM 2
COM
DC
COM
DC
COM
IN 1
IN 0
HSC
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
IN 13
IN 12
IN 15
IN 14
IN 17
IN 16
IN 19
IN 18
IN 21
IN 20
IN 23
IN 22
Commons
Connected
Internally
10-30
VDC
- DC
+ DC
1. The outputs are isolated in groups as shown. Therefore, different voltages can be applied to each group as the specific application requires.
2. 24 VDC, 200mA user power is available for sensors.
1747-L40E
+ DC
- DC
CR
+ DC
- DC
1
10-50 VDC
1
10-50 VDC
CR
CR
CR
CR
CR
CR
CR
VDC 1 OUT 0 OUT 1 OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 OUT 7 DC
VDC 2 OUT 8 OUT 9 OUT 10 OUT 1 1 OUT 12 OUT 13 OUT 14 OUT 15 DC
COM 1
COM 2
Sourcing Device
(Hi)
L1
(Lo)
L2
85-265
VAC
120/240 VAC
VAC
NEUT
CHASSIS
GND
PWR OUT DC
+24VDC 2 COM
PWR OUT DC
COM 2
COM
DC
COM
DC
COM
IN 1
IN 0
HSC
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
IN 13
IN 12
IN 15
IN 14
IN 17
IN 16
IN 19
IN 18
IN 21
IN 20
IN 23
IN 22
Commons
Connected
Internally
10-30
VDC
- DC
+ DC
1. The outputs are isolated in groups as shown. Therefore, different voltages can be applied to each group as the specific application requires.
2. 24 VDC, 200mA user power is available for sensors.
Publication CIG-WD001B-EN-P - May 2005
6-6
1747 I/O on Fixed Hardware Controllers
1747-L40F
(Hi)
L1
5-265 V AC
5-125 VDC
(Hi)
L1
(Lo)
L2
5-265 V AC
5-125 VDC
1
CR
CR
(Hi)
L1
(Lo)
L2
5-265 V AC
5-125 VDC
1
CR
(Hi)
L1
(Lo)
L2
5-265 V AC
5-125 VDC
1
CR
CR
(Lo)
L2
1
CR
CR
CR
VAC
OUT 0 OUT 1 OUT 2 OUT 3 VAC
OUT 4 OUT 5 OUT 6 OUT 7 VAC
OUT 8 OUT 9 OUT 10 OUT 1 1 VAC
OUT 12 OUT 13 OUT 14 OUT 15
VDC 1
VDC 2
VDC 3
VDC 4
- DC
+ DC
10-30 VDC
+
-
24 VDC
+ 10 %
+ 24
VDC
VDC
NEUT
NOT
USED
EAR TH NOT
GND
USED
DC
COM
DC
COM
DC
COM
DC
COM
IN 0
HSC
IN 1
IN 3
IN 2
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
IN 13
IN 12
IN 15
IN 14
IN 17
IN 16
IN 19
IN 18
IN 21
IN 20
IN 23
IN 22
Commons
Connected
Internally
Sourcing Device
1. The outputs are isolated in groups as shown. Therefore, different voltages can be applied to each group as the specific application requires.
Publication CIG-WD001B-EN-P - May 2005
Chapter
7
1756 ControlLogix I/O Modules
1756-CFM - Standard Flowmeter Wiring
2
1756-CFM - Standard Prover/Detector Wiring
1
12-24V dc
Z0 12-24V dc
Z1 12-24V dc
4
3
6
5
8
7
–
F1
10
9
12
11
14
13
16
15
18
17
F0 Return
Input
Device
F1 Return
Not used
Shield
ground
Shield ground
Z1 RET
F0
+
20
19
6
5
8
7
Z1 5V dc
Z0 Return
Z1 RET
F0
F1
10
9
12
11
F0 Return
F1 Return
Not used
Not used
14
16
15
18
17
20
19
Output 0
+
Load
–
Customer VCC
Customer VCC
11
14
13
16
15
18
17
20
19
F1 Return
Not used
Not used
Output 1
Customer
Common
Customer
Common
Customer VCC
NOTE: 1. The wiring example above shows a 12-24V dc standard prover connected to the
module. If you use a 5V dc standard prover, make sure the positive wire is connected to
the 5V terminal (e.g. Z0 5V dc).
2. Do not connect more than 2 wires to any terminal.
Z0 (12-24V)
2
1
Z1 (12-24V)
Z0 (5V)
4
3
Z1 (5V)
Z0 (RET)
6
5
Z1 (RET)
B0 (12-24V)
8
7
B1 (12-24V)
B0 (5V)
10
9
B1 (5V)
B0 (RET)
A0 (12-24V)
12
11
14
13
B1 (RET)
A1 (12-24V)
A0 (5V)
16
15
A1 (5V)
A0 (RET)
18
17
A1 (RET)
20
19
Not used
Not used
22
21
Not used
24
23
Output 1
Not used
Out 0
26
25
Not used
Out 2
Out 1
28
27
Out 3
COMMON 0
30
29
COMMON 1
COMMON 0
32
31
COMMON 1
COMMON 0
34
33
COMMON 1
DC-0(+)
36
35
DC-1(+)
Customer
Common
+
12
F1
Customer VCC
Not used
Customer
Common
9
Not used
Not used
13
Not used
10
Z1 RET
1756-HSC - 845 Incremental Encoder
Z1 12-24V dc
Z0 5V dc
7
F0 Return
Customer
Common
1
3
8
Z1 5V dc
Output 0
1756-CFM - Standard Output
4
5
Not used
NOTES: 1. This wiring diagram can be used in applications with 50mV (magnetic pickup),
1.3V (TTL), and 4V (preamp level) thresholds. You must use RSLogix 5000 to
choose the appropriate threshhold level for your application.
2. Do not connect more than 2 wires to any single terminal.
2
–
Customer
Common
Customer VCC
Z0 12-24V dc
+
Output 1
Customer VCC
6
F0
Not used
Output 0
3
Z0 Return
Shield ground
Not used
Not used
Z1 1224V dc
4
Z0 5V dc
Z1 5V dc
Z0 Return
1
Z0 12-24V dc
–
Z0 5V dc
Input
Device
2
+
+
Load
–
Allen-Bradley
Bulletin 845
Incremental
Encoder
Green
Black
Blue
Black
White
Differential Line
Driver Output
Black
–
NOTES: 1. If separate power sources are used, do not exceed the specified isolation voltage.
2. Do not connect more than 2 wires to any single terminal.
Appl ic ation :
A1 Co nne cti ons:
B 1 Co nne cti ons:
Z1 Con nect ions :
Differential
Line Driver
Output (40mA)
White - A1 (5V)
Black of white - A1
(RET)
Blue - B1 (RET)
Black of blue - B1 (5V)
Green - Z1 (5V)
Black of green - Z1
(RET)
NOTE: Do not connect more than 2 wires to any single terminal.
1
Publication CIG-WD001B-EN-P - May 2005
7-2
1756 ControlLogix I/O Modules
1756-HSC - 872 3-Wire DC Proximity Sensor
Allen-Bradley
Bulletin 872
3-Wire DC
Proximity
Sensor
Z0 (12-24V)
Jumpers
Black
12-24V dc
Blue
12-24V dc
Return
2
1756-HSC - Photoswitch Series 10,000
Photoelectric Sensor
Z1 (12-24V)
1
Z0 (5V)
4
3
Z1 (5V)
Z0 (RET)
6
5
Z1 (RET)
Z0 (12-24V)
2
1
Z1 (12-24V)
Z0 (5V)
4
3
Z1 (5V)
Z0 (RET)
6
5
Z1 (RET)
Photoswitch
Series 10,000
Photoelectric
Sensor
White
Blue
B0 (12-24V)
8
7
B1 (12-24V)
B0 (12-24V)
9
7
10-30V dc
10
8
B1 (12-24V)
B0 (5V)
B1 (5V)
B0 (5V)
10
9
B1 (5V)
Not used
12 11
B0 (RET)
A0 (12-24V)
12
11
14
13
B1 (RET)
A1 (12-24V)
B0 (RET)
A0 (12-24V)
A0 (5V)
16
15
A1 (5V)
14 13
B1 (RET)
A1 (12-24V)
A0 (5V)
18
17
16 15
A1 (5V)
A0 (RET)
A1 (RET)
A0 (RET)
A1 (RET)
Not used
18 17
20
19
Not used
Not used
22
21
20 19
Not used
Not used
Not used
Not used
22 21
Not used
Not used
Out 0
24
23
26
25
Not used
Out 2
Not used
Out 0
24 23
26 25
Not used
Out 2
Out 1
28
27
Out 3
Out 1
28 27
Out 3
COMMON 0
30
29
COMMON 1
COMMON 0
COMMON 1
COMMON 0
30 29
32
31
COMMON 1
COMMON 0
32 31
COMMON 1
COMMON 0
34
33
COMMON 1
COMMON 0
DC-0(+)
36
35
DC-1(+)
34 33
DC-0(+)
36 35
Black
Jumper
12-24V dc
Return
COMMON 1
DC-1(+)
Appl ic ation :
A0 Co nne cti ons:
B 0 Co nne cti ons:
Z0 Con nect ions :
Appl ic ation :
A1 Co nne cti ons:
B 1 Co nne cti ons:
Z1 Con nect ions :
PNP (Sourcing)
N.O.
Black - A0 (12-24V)
Blue, PS(-)- A0 (RET)
Jumper B0 (12-24V) to
B0 (RET)
Jumper Z0 (12-24V) to
Z0 (RET)
Any
Black - A1 (12-24V)
Blue - A1 (RET)
Jumper B1 (12-24V) to
B1 (RET)
White - Z1 (12-24V)
Blue - Z1 (RET)
NOTE: Do not connect more than 2 wires to any single terminal.
NOTE: Do not connect more than 2 wires to any single terminal.
1756-HYD02
+O UT-0
+O UT-1
-OU T-0
-OUT -1
+E NABL E-0
+EN ABLE- 1
-ENA BL E-0
-ENABLE-1
DR VF LT-0
DR VF LT-1
CH AS SIS
CH AS SIS
IN _COM
IN _COM
HO ME -0
HO ME -1
RE G2 4V-0
REG 24V-1
RE G5 V-0
REG 5V-1
+O K
CH AS SIS
General cable CO720
To valve driver/amplifier
General cable CO721
To hydraulic control unit
or
To valve or pump
General cable CO720
To home
limit switch
General cable CO720
To registration
sensor
5V dc
Field Power
Supply
+
–
5 Volt
Registration
Sensor
Supply
From 1756-HYD02
General cable
C0720
REG5V
IN_COM
Output
Common
-O K
CH AS SIS
+IN T-0
+INT-1
-INT-0
-INT-1
+R ET-0
+RE T-1
-R ET-0
1756-HYD02 - Wiring 5V Sensors
-R ET-1
LD T C MN
LD T CMN
CH AS SIS
CH AS SIS
1756-HYD02 - Wiring 24V Sensors
General cable CO722
To L D T
24V dc
Field Power
Supply
+
–
General cable CO720
To E-stop relay coil
24 Volt
Registration
Sensor
Supply
NOTES: 1. This is a general wiring example illustrating Axis 1 wiring only. Other configurations are possible with Axis wiring identical to Axis 1.
2. Make sure that any transducer connected t othe 1756-HYD02 module uses an external interrogation signal.
3. Do exceed the specified isolation voltage between power sources.
Publication CIG-WD001B-EN-P - May 2005
From 1756-HYD02
General cable
C0720
REG24V
IN_COM
Output
Common
1756 ControlLogix I/O Modules
1756-HYD02 - Wiring Home Limit Switch
7-3
1756-HYD02 - Wiring OK Contacts
24V dc
Field Power
Supply
24V dc
Field Power
Supply
+
–
+
–
OK Pilot
Relay
From 1756-HYD02
HOME
IN_COM
General cable
C0720
+OK
-OK
General cable
C0720
From 1756-HYD02
OK Pilot
Relay
Contacts
CR1
Start
Stop
CR1
M1
24V AC/DC
or 120VAC
typical
CR1
1756-IA16
2
1
4
3
IN-1
IN-0
Group 0
Daisy
chain to
other
RTBs
L2-0
2
1
IN-0
L2-1
4
3
IN-1
L2-2
6
5
IN-2
L2-3
8
7
IN-3
L2-4
10
9
IN-4
L2-5
12 11
IN-5
L2-6
14 13
IN-6
L2-7
16 15
IN-7
L2-8
18 17
IN-8
L2-9
20 19
IN-9
L2-10
22 21
IN-10
L2-11
24 23
IN-11
L2-12
26 25
IN-12
L2-13
L2-14
28 27
IN-13
30 29
IN-14
L2-15
32 31
IN-15
L2-15
Not used
34 33
Not used
Not used
L2-0
IN-3
IN-2
6
5
8
7
10
9
12
11
14
13
IN-5
IN-4
IN-7
Group 0
L2-2
L2-4
IN-6
L2-0
L2-0
IN-9
Jumper bar - Cut to length
IN-8
(Part number 97739201)
IN-11
IN-10
16
Group 1
1756-IA16I
Isolated
wiring
15
IN-13
IN-12
18
17
20
19
IN-15
Group 1
IN-14
L2-1
Non-isolated
wiring
L2-1
L2
L1
NOTES: 1. All terminals with the same name are connected together on the module. For
example, L2 can be connected to any terminal marked L2-0.
2. When you daisy chain from a group to another RTB, always connect the daisy
chain as shown above. Do not connect more than 2 wires to any single terminal.
3. This wiring example shows a single voltage source.
L2
36 35
L1-0
L1-2
L1-4
L1
Daisy chain to other RTBs
NOTES
1. All terminals with the same name are connected together on the module. For
example, L2 can be connected to either terminal marked L2-15.
2. When you use the second L2-15 terminal to daisy chain to other RTBs, always
connect the daisy chain to the terminal directly connected to the supply wire, as
shown in the example above. Do not connect more than 2 wires to any single terminal.
Publication CIG-WD001B-EN-P - May 2005
7-4
1756 ControlLogix I/O Modules
1756-IA32
IN-1
IN-3
IN-5
IN-7
IN-9
IN-11
IN-13
IN-15
L2-0
IN-17
IN-19
IN-21
IN-23
IN-25
IN-27
IN-29
IN-31
L2-1
Group 0
Daisy chain
to other RTBs
Group 1
2
IN-0
IN-2
IN-4
IN-6
IN-8
IN-10
IN-12
IN-14
1
4
3
6
5
8
7
10
1756-IA8D
9
12 11
14 13
16 15
18 17
L2-0
IN-16
IN-18
IN-20
IN-22
IN-24
IN-26
IN-28
IN-30
L2-1
20 19
22 21
24 23
26 25
28 27
30 29
32 31
34 33
36 35
Daisy chain to
other RTBs
Group 0
Group 0
1
Daisy chain
to other
RTBs
Group 1
IN-4
9
L1
13
Group 0
Group 2
15
IN-12
IN-13
18
17
20
19
Group 1
IN-14
IN-15
GND-1
GND-1
–
16
15
IN-4
IN-5
IN-6
L2-1
18
17
20
19
47kΩ, 1/2W,
5% resistor
Group
1
IN-7
L1-1 Loss of Field Power
To Determine Leakage Resistor
(P/S = Field side power supply)
RLEAKMaximum = (P/S Voltage-19V ac)/1.5mA
RLEAKMinimum = (P/S Voltage-20V ac)/2.5mA
Group 0
IN-10
IN-11
16
13
Resistors are not necessary if Wire Off diagnostic
is not used.
IN-8
IN-9
Group 1
14
L1
GND-0
11
11
NOTES: 1. All terminals with the same name are connected together on the module. For example,
L2 can be connected to any terminal marked L2-0.
2. This wiring example shows a single voltage source.
3. When you daisy chain from a group to other RTBs, alway connect the daisy chain to the
terminal directly connected to the supply wire, as shown above. Do not connect more
than 2 wires to any single terminal.
4. If separate power sources are used, do not exceed the specified isolation voltage.
Group 1
GND-0
14
12
L2
IN-6
IN-7
12
47kΩ, 1/2W,
5% resistor
IN-3
L2-1
Group 1
Group
0
IN-2
L2-1
5
IN-5
7
9
L2-1
IN-2
10
10
IN-1
Recommended Values
P/S Voltage
RLEAK, 1/2W, 5%
100V ac +/-10%
43k Ω
110V ac +/-10%
47k Ω
115V ac +/-10%
47k Ω
120V ac +/-10%
51k Ω
Daisy chain to other RTBs
IN-3
8
7
L2-1
IN-0
6
8
IN-0
1756-IB16D
IN-1
Group 0
5
L2-0
1756-IB16
3
6
L1-0 Loss of Field Power
L2-0
L2-0
NOTES: 1. All terminals with the same name are connected together on the module. For example, L2 can
be connected to any terminal marked L2-0.
2. When you daisy chain from a group to another RTB, always connect the daisy chain as shown
above. Do not connect more than 2 wires to any single terminal.
3. This wiring example shows a single voltage source.
4. If separate power sources are used, do not exceed the specified isolation voltage.
2
1
3
L2-0
L2
4
2
4
Not used
Group 3
+
GND-0
2
1
IN-0
GND-0
GND-0
4
3
6
5
IN-1
IN-2
GND-0
8
7
IN-3
GND-1
GND-1
10
9
12 11
IN-4
IN-5
GND-1
14 13
IN-6
GND-1
16 15
IN-7
GND-2
18 17
IN-8
GND-2
GND-2
20 19
IN-9
IN-10
GND-2
GND-3
24 23
26 25
IN-11
IN-12
GND-3
28 27
IN-13
GND-3
GND-3
GND-3
30 29
34 33
IN-14
IN-15
Not used
36
Not used
22 21
32 31
Not used
35
14.3kΩ, 1/4W,
2% resistor
Group 0
Group 1
14.3kΩ, 1/4W,
2% resistor
Group 2
Group 3
DC COM
NOTES: 1. All terminals with the same name are connected together on the module. For
example, DC COM can be connected to either terminal marked GND-0.
2. When you daisy chain from a group to another RTB, always connect the daisy
chain as shown above. Do not connect more than 2 wires to any single terminal.
3. This wiring example shows a single voltage source.
4. If separate power sources are used, do not exceed the specified isolation voltage.
–
+
DC COM
NOTES:
1. All terminals with the same name are connected together on the module.
2. This wiring example shows a single voltage source.
3. When you daisy chain from a group to other RTBs, alway connect the daisy chain to the
terminal directly connected to the supply wire, as shown above. Do not connect more
than 2 wires to any single terminal.
4. Resistors are not necessary if Wire Off diagnostic is not used.
5. If separate power sources are used, do not exceed the specified isolation voltage.
To Determine Leakage Resistor
(P/S = Field side power supply)
RLEAKMaximum = (P/S Voltage- 4.6V dc)/1.21mA
RLEAKMinimum = (P/S Voltage- 5V dc)/1.5mA
Publication CIG-WD001B-EN-P - May 2005
Recommended Values
P /S Voltage
R LE AK, 1/4W, 2%
12V dc +/-5%
5.23k Ω
24V dc +/-5%
14.3k Ω
1756 ControlLogix I/O Modules
1756-IB16I
1756-IB16ISOE
Isolated wiring
Sink input wiring
DC-0 (-)
DC-5 (-)
–
+
Jumper bar
(Part number 97739201)
Non-isolated
wiring
DC (-)
GND-0
2
1
IN-0
GND-1
4
3
IN-1
GND-2
6
5
IN-2
GND-3
8
7
IN-3
GND-4
10
9
IN-4
GND-5
12 11
IN-5
GND-6
14 13
IN-6
GND-7
16 15
IN-7
GND-8
18 17
IN-8
GND-9
20 19
IN-9
GND-10
22 21
IN-10
GND-11
24 23
IN-11
GND-12
26 25
IN-12
GND-13
GND-14
28 27
IN-13
30 29
IN-14
GND-15
32 31
IN-15
GND-15
Not used
34 33
Not used
Not used
36 35
DC-0 (+)
Source input wiring
(+)
DC-5 (+)
Non-isolated wiring
DC (+)
Sink input wiring
Isolated wiring
GND-0
DC-0 (-)
GND-1
GND-2
GND-3
GND-4
Source input wiring
GND-5
GND-6
DC-6 (-)
GND-7
GND-8
GND-9
GND-10
Jumper bar
GND-11
(Part number 97739201)
GND-12
GND-13
Non-isolated
GND-14
wiring
GND-15
GND-15
DC (-)
Not used
Daisy chain to other RTBs
NOTES:
Daisy chain
to other RTBs
Group 1
4
3
6
5
8
7
IN-0
DC-0 (+)
IN-1
IN-2
IN-3
IN-4
Source input wiring
IN-5
IN-6
DC-6 (+)
IN-7
IN-8
IN-9
IN-10
IN-11
Sink input wiring
IN-12
IN-13
IN-14
IN-15
Not used
Not used
DC (+)
10 9
12 11
14 13
16 15
18 17
20 19
22 21
24 23
26 25
28 27
30 29
32 31
34 33
36 35
2
1
4
3
6
5
8
7
10
9
1756-IC16
IN-21
IN-23
IN-25
IN-27
IN-29
IN-31
24 23
34 33
IN-0
IN-2
IN-4
IN-6
IN-8
IN-10
IN-12
IN-14
GND-0
IN-16
IN-18
IN-20
IN-22
IN-24
IN-26
IN-28
IN-30
GND-1
36 35
GND-1
DC COM –
1
1. All terminals with the same name are connected together on the module. For
example, DC (-) can be connected to either terminal marked GND-15.
2. When you use the second GND-15 terminal to daisy chain to other RTBs, always
connect the daisy chain to the terminal directly connected to the supply wire, as
shown in the example above.
3. If separate power sources are used, do not exceed the specified isolation voltage.
4. Do not connect more than 2 wires to any single terminal.
5. The jumper bar is part number 97739201; use this number to order additional bars.
1756-IB32/B
Group 0
2
Daisy chain to other RTBs
NOTES: 1. All terminals with the same name are connected together on the module. For
example, DC (-) can be connected to either terminal marked GND-15.
2. When you use the second GND-15 terminal to daisy chain to other RTBs, always
connect the daisy chain to the terminal directly connected to the supply wire, as
shown in the example above. Do not connect more than 2 wires to any single terminal.
3. Each input can be wired in a sink or source configuration, as shown above.
4. If separate power sources are used, do not exceed the specified isolation voltage.
IN-1
IN-3
IN-5
IN-7
IN-9
IN-11
IN-13
IN-15
GND-0
IN-17
IN-19
7-5
12 11
14 13
16 15
18 17
20 19
22 21
26 25
28 27
30 29
32 31
2
1
4
3
6
5
8
7
IN-1
IN-0
IN-3
Group 0
Group 0
IN-2
IN-5
IN-4
IN-7
10
9
12
11
14
13
16
15
18
17
20
19
GND-0
GND-0
IN-9
IN-8
IN-11
Group 1
Group 1
IN-10
IN-13
IN-11
IN-15
GND-1
Daisy chain to other RTBs
–
+
DC COM
NOTES: 1. All terminals with the same name are connected together on the module. For example, DC
COM can be connected to either terminal marked GND-1.
2. When you daisy chain to other RTBs, always connect the daisy chain as shown above. Do not
connect more than 2 wires to any single terminal at any time.
3. This wiring example shows a single voltage source.
4. If separate power sources are used, do not exceed the specified isolation voltage.
Group 1
IN-14
GND-1
+
Group 0
IN-6
NOTES:
1. All terminals with the same name are connected together on the module. For
example, DC COM can be connected to any terminal marked GND-1.
2. When you daisy chain from a group to another RTB, always connect the daisy chain to
the terminal directly connected to the supply wire, as shown above. Do not connect
more than 2 wires to any single terminal.
3. This wiring example shows a single voltage source.
4. If separate power sources are used, do not exceed the specified isolation voltage.
Publication CIG-WD001B-EN-P - May 2005
7-6
1756 ControlLogix I/O Modules
1756-IF16 – Differential Current Applications
Channel 0
i
Channel 0
A
Shield ground
Channel 3
2-Wire
Transmitter
Channel 6
i
A
i
+
+
A
4-Wire
Transmitter
24V dc
–
–
1756-IF16 – Differential Voltage Applications
IN-0
IN-1
IN-2
IN-3
RTN
IN-4
IN-5
IN-6
IN-7
IN-8
IN-9
IN-10
IN-11
RTN
IN-12
IN-13
IN-14
IN-15
2
1
4
3
6
5
8
7
10
9
i RTN-0
i RTN-1
i RTN-2
i RTN-3
RTN
i RTN-4
i RTN-5
i RTN-6
i RTN-7
i RTN-8
i RTN-9
i RTN-10
i RTN-11
RTN
i RTN-12
i RTN-13
i RTN-14
i RTN-15
12 11
14 13
16 15
18 17
20 19
22 21
24 23
26 25
28 27
30 29
32 31
34 33
36 35
Jumper
wires
+
–
Shield ground
Channel 3
+
–
Shield ground
Shield ground
IN-0
IN-1
2
1
4
3
i RTN-0
i RTN-1
IN-2
6
5
i RTN-2
IN-3
8
7
i RTN-3
RTN
IN-4
IN-5
IN-6
IN-7
IN-8
IN-9
10
9
RTN
i RTN-4
i RTN-5
i RTN-6
i RTN-7
i RTN-8
i RTN-9
IN-10
IN-11
RTN
IN-12
IN-13
24 23
32 31
i RTN-10
i RTN-11
RTN
i RTN-12
i RTN-13
IN-14
34 33
i RTN-14
IN-15
36 35
i RTN-15
12 11
14 13
16 15
18 17
20 19
22 21
26 25
28 27
30 29
NOTES:
1. Use the table below when wiring your module in differential current mode.
Th is
c han nel :
Uses t hese terminal s:
Th is
ch ann el :
NOTES: 1. Use the following chart when wiring your module in differential mode
Uses t hese t erm inal s:
This channel :
Uses these terminals:
This channel:
Uses these terminals:
Channel 0
IN-0 (+) & IN-1 (-)
Channel 4
IN-8 (+) & IN-9 (-)
Channel 1
IN-2 (+) & IN-3 (-)
Channel 5
IN-10 (+) & IN-11 (-)
Channel 0
IN-0 (+), IN-1 (-) & i RTN-0
Channel 4
IN-8 (+), IN-9 (-) & i RTN-8
Channel 2
IN-4 (+) & IN-5 (-)
Channel 6
IN-12 (+) & IN-13 (-)
Channel 1
IN-2 (+), IN-3 (-) & i RTN-2
Channel 5
IN-10 (+), IN-11 (-) & i RTN-10
Channel 3
IN-6 (+) & IN-7 (-)
Channel 7
IN-14 (+) & IN-15 (-)
Channel 2
IN-4 (+), IN-5 (-) & i RTN-4
Channel 6
IN-12 (+), IN-13 (-) & i RTN-12
Channel 3
IN-6 (+), IN-7 (-) & i RTN-6
Channel 7
IN-14 (+), IN-15 (-) & i RTN-14
2. All terminals marked RTN are connected internally.
3. A 249 current loop resistor is located between IN-x and i RTN-x terminals.
4. If multiple (+) or multiple (-) terminals are tied together, connect that tie point to a RTN terminal to
maintain the module’s accuracy.
2. When operating in 4 channel, high speed mode, only use channels 0, 2, 4 and 6
3. All terminals marked RTN are connected internally.
4. If multiple (+) or multiple (-) terminals are tied together, connect that tie point to
terminal to maintain the module’s accuracy.
5. Terminals marked RTN and i RTN are not used for differential voltage wiring.
6. Do not connect more than 2 wires to any single terminal.
5. Place additional loop devices (e.g. strip chart recorders, etc.) at the A location in the current loop.
6. Do not connect more than two wires to any single terminal.
IMP ORTANT: When operating in 4 ch annel, high sp eed mo de, only use channels 0, 2, 4 and 6.
1756-IF16 – Single-Ended Current Applications
1756-IF16 – Single-Ended Voltage Applications
i
2
1
4
3
i RTN-0
i RTN-1
IN-2
6
5
i RTN-2
IN-3
8
7
i RTN-3
RTN
IN-4
IN-5
IN-6
IN-7
IN-8
IN-9
10
9
RTN
i RTN-4
i RTN-5
i RTN-6
i RTN-7
i RTN-8
i RTN-9
IN-10
IN-11
RTN
IN-12
IN-13
24 23
32 31
i RTN-10
i RTN-11
RTN
i RTN-12
i RTN-13
IN-14
34 33
IN-15
36 35
IN-0
IN-1
Shield
ground
2-Wire
Transmitter
i
A
12 11
14 13
16 15
18 17
20 19
22 21
26 25
28 27
30 29
+
2
1
4
3
i RTN-0
i RTN-1
IN-2
6
5
i RTN-2
IN-3
8
7
i RTN-3
RTN
IN-4
IN-5
IN-6
IN-7
IN-8
IN-9
10
9
RTN
i RTN-4
i RTN-5
i RTN-6
i RTN-7
i RTN-8
i RTN-9
24 23
i RTN-14
IN-10
IN-11
RTN
IN-12
IN-13
32 31
i RTN-10
i RTN-11
RTN
i RTN-12
i RTN-13
i RTN-15
IN-14
34 33
i RTN-14
IN-15
36 35
i RTN-15
Jumper
wires
NOTES: 1. All terminals marked RTN are connected internally.
2. A 249Ω current loop resistor is located between IN-x and i RTN-x terminals.
3. For current applications, all terminals marked i RTN must be wired to terminals
marked RTN.
4. Place additional loop devices (e.g. strip chart recorders, etc.) at the A location.
5. Do not connect more than 2 wires to any single terminal.
Publication CIG-WD001B-EN-P - May 2005
–
Shield
ground
+
–
Shield
ground
IN-0
IN-1
12 11
14 13
16 15
18 17
20 19
22 21
26 25
28 27
30 29
NOTES: 1. All terminals marked RTN are connected internally.
2. Terminals marked i RTN are not used for single-ended voltage wiring.
3. Do not connect more than 2 wires to any single terminal.
1756 ControlLogix I/O Modules
1756-IF4FXOF2F Current Mode
(+)
(-)
1756-IF4FXOF2F Voltage Mode
A
(+)
(+)
i
2-Wire
A
Transmitter
+IN-1/V
IN-1/I
-IN-1
2
1
4
3
6
5
+IN-0/V
IN-0/I
-IN-0
+IN-3/V
8
7
+IN-2/V
User
Analog
Input
Device
(-)
IN-3/I
10 9
-IN-3
Not used
Not used
V OUT-1
12 11
I OUT-1
RTN-1
20 19
Not used
Not used
24 23
Not used
Not used
28 27
30 29
Not used
Not used
Not used
32 31
Not used
34 33
Not used
36 35
14 13
16 15
18 17
22 21
26 25
IN-2/I
-IN-2
+IN-1/V
IN-1/I
-IN-1
2
1
4
3
6
5
+IN-0/V
IN-0/I
-IN-0
+IN-3/V
8
7
+IN-2/V
IN-2/I
-IN-2
IN-3/I
-IN-3
Not used
Not used
V OUT-1
10 9
I OUT-1
RTN-1
20 19
Not used
Not used
24 23
Not used
Not used
28 27
30 29
Not used
Not used
Not used
Not used
32 31
Not used
Not used
Not used
34 33
Not used
Not used
36 35
Not used
Not used
Not used
Not used
V OUT-0
I OUT-0
RTN-0
Shield
ground
i
Current
Output
Load
A
Not used
Not used
7-7
Shield
ground
12 11
14 13
16 15
18 17
22 21
26 25
Not used
Not used
(+)
V OUT-0
I OUT-0
RTN-0
Not used (-)
Not used
Shield
ground
NOTE: Place additional loop devices (e.g. strip chart recorders) at any A location.
1756-IF6CIS - 2-Wire transmitter connected to the module
and the module providing 24V dc loop power
1
2
VOUT-1
VOUT-0
4
3
6
5
IN-1/I
IN-0/I
RTN-1
RTN-0
8
A
2-Wire
Transmitter
–
10
VOUT-1
IN-1/I
i
11
14
13
16
15
18
17
20
19
RTN-3
Shield ground
Not used
VOUT-5
VOUT-4
IN-5/I
RTN-0
7
VOUT-3
RTN-2
Not used
5
8
IN-2/I
IN-4/I
RTN-4
NOT ES: 1. Do not connect more than 2 wires to any single terminal.
A
24V dc
–
+
2-Wire
Transmitter
VOUT-2
10
9
12
11
14
13
16
15
18
17
20
19
IN-3/I
IN-2/I
RTN-3
RTN-2
Not used
Shield ground
Not used
VOUT-5
VOUT-4
IN-5/I
RTN-5
A
IN-0/I
RTN-1
9
12
VOUT-0 i
3
4
6
VOUT-2
IN-3/I
1
2
+
7
VOUT-3
RTN-5
A
1756-IF6CIS - 2-Wire transmitter connected to the module and an
external, user-provided power supply providing 24V dc loop power
IN-4/I
RTN-4
NOTES: 1. If separate power sources are used, do not exceed the
specified isolation voltage.
2. Place additional loop devices (e.g. strip chart recorders) at either
A location in the current loop.
2. Do not connect more than 2 wires to any single terminal.
3. Place additional loop devices (e.g. strip chart recorders) at
either A location in the current loop.
Publication CIG-WD001B-EN-P - May 2005
7-8
1756 ControlLogix I/O Modules
1756-IF6CIS - 4-Wire transmitter connected to the module and an
external, user-provided power supply providing 24V dc loop power
1756-IF6I - Current Application with 2-Wire Transmitter
1
2
VOUT-0 i
3
4
IN-1/V
A
IN-1/I
IN-0/I
6
5
RTN-1
RTN-0
8
7
10
9
VOUT-3
A
4-Wire
Transmitter
–
16
15
Not used
8
Shield ground
18
10
9
12
11
14
13
16
15
18
17
20
19
IN-2/I
RET-3
RET-2
Not used
Not used
IN-4/I
20
A
7
IN-3/I
17
19
RTN-5
IN-4/V
IN-5/V
RTN-4
IN-4/I
IN-5/I
NO TE S: 1. If separate power sources are used, do not exceed the
RET-4
RET-5
specified isolation voltage.
A
IN-2/V
VOUT-4
IN-5/I
2-Wire
Transmitter
i
RET-0
IN-3/V
Not used
VOUT-5
5
RET-1
RTN-2
13
6
IN-0/I
–
11
14
3
IN-1/I
24V dc
IN-2/I
RTN-3
4
+
–
IN-0/V
+
+
VOUT-2
IN-3/I
12
1
2
VOUT-1
2. Do not connect more than 2 wires to any single terminal.
3. Place additional loop devices (e.g. strip chart recorders) at
either A location in the current loop.
NOTES:
1. Place additional loop devices (e.g. strip chart recorders, etc.) at either A location.
2. If separate power sources are used, do not exceed the specified isolation voltage.
1756-IF6I - Current Application with 4-Wire Transmitter
2
IN-0/V
4
3
6
5
8
7
IN-1/I
RET-0
IN-3/V
12
A
A
i
4-Wire
Transmitter
IN-1/I
–
RET-1
IN-2/V
IN-3/V
IN-2/I
IN-3/I
11
RET-3
RET-2
14
13
16
15
18
17
Not used
Shield Ground
Not used
IN-5/V
IN-4/V
IN-5/I
IN-4/I
20
User Analog
Input Device
IN-0/I
6
5
8
7
RET-0
–
Device
External
Power
IN-2/V
10
9
12
11
14
13
16
15
18
17
20
19
IN-2/I
RET-2
Not used
Not used
IN-5/V
IN-4/V
IN-5/I
RET-5
+
3
RET-3
19
RET-4
IN-0/V
4
9
IN-3/I
1
IN-1/V
+
IN-0/I
RET-1
RET-5
Voltage Input
1
2
IN-1/V
10
1756-IF6I - Voltage Application
IN-4/I
Shield Ground
RET-4
NOTES: Do not connect more than 2 wires to any single terminal.
NOTES: 1. Place additional loop devices (e.g. strip chart recorders, etc.) at either A location.
2. Do not connect more than 2 wires to any single terminal.
Publication CIG-WD001B-EN-P - May 2005
1756 ControlLogix I/O Modules
1756-IF8 – Differential Current Applications
1756-IF8 – Differential Voltage Applications
Channel 0
Channel 0
i
To field
device
A
Shield
ground
Channel 3
2-Wire
Transmitter
i
A
IN-0
2
1
i RTN-0
IN-1
4
3
i RTN-1
IN-2
6
5
i RTN-2
IN-3
8
7
i RTN-3
RTN
10
9
RTN
IN-4
12 11
14 13
i RTN-5
IN-6
16 15
i RTN-6
IN-7
18 17
i RTN-7
Not used
20 19
Not used
Not used
22 21
Not used
Not used
24 23
Not used
Not used
26 25
Not used
Not used
28 27
Not used
Not used
30 29
Not used
Not used
32 31
Not used
Not used
34 33
Not used
Not used
36 35
Not used
+
–
Jumper
wires
i RTN-4
IN-5
7-9
Shield ground
Channel 3
+
–
Shield ground
IN-0
2
1
i RTN-0
IN-1
4
3
i RTN-1
IN-2
6
5
i RTN-2
IN-3
8
7
i RTN-3
RTN
10
9
RTN
IN-4
12
11
i RTN-4
IN-5
14
13
i RTN-5
IN-6
16
15
i RTN-6
IN-7
18
17
i RTN-7
Not used
Not used
20
19
22
21
Not used
Not used
Not used
24
23
Not used
Not used
26
25
Not used
Not used
28
27
Not used
Not used
30
29
Not used
Not used
32
31
Not used
Not used
34
33
Not used
Not used
36
35
Not used
NOTES: 1. Use the following chart when wiring your module in differ ential mode
NOTES: 1. Use the following chart when wiring your module in differential mode
Thi s channel:
Uses t hese ter minals:
Thi s channel:
Uses these terminals:
This channel:
Uses these terminals:
This channel :
Uses these ter minals:
Channel 0
IN-0 & IN-1
Channel 2
IN-4 & IN-5
Channel 0
IN-0, IN-1 & i RTN-0
Channel 2
IN-4, IN-5 & i RTN-4
Channel 1
IN-2 & IN-3
Channel 3
IN-6 & IN-7
Channel 1
IN-2, IN-3 & i RTN-2
Channel 3
IN-6, IN-7 & i RTN-6
2. When operating in 2 channel, high speed mode, only use channels 0 and 2.
3. All terminals marked RTN are connected internally.
4. If multiple (+) or multiple (-) terminals are tied together, connect that tie point to a RTN
terminal to maintain the module’s accuracy.
5. Terminal marked RTN or i RTN are not used in differential voltage applications.
6. Do not connect more than 2 wires to any single terminal.
2.
3.
4.
5.
When operating in 2 channel, high speed mode, only use channels 0 and 2.
All terminals marked RTN are connected internally.
A 249Ω current loop resistor is located between IN-x and i RTN-x terminals.
If multiple (+) or multiple (-) terminals are tied together, connect that tie point to a RTN
terminal to maintain the module’s accuracy.
6. Place additional loop devices (e.g. strip chart recorders, etc.) at the A location.
7. If separate power sources are used, do not exceed the specified isolation voltage.
8. Do not connect more than 2 wires to any single terminal.
1756-IF8 – Single-Ended Current Applications
Channel 0
i
To field
device
Shield ground
Channel 5
2-Wire
Transmitter
1756-IF8 – Single-Ended Voltage Applications
i
A
Channel 0
IN-0
2
1
i RTN-0
IN-1
4
3
i RTN-1
IN-2
6
5
i RTN-2
IN-3
8
7
i RTN-3
RTN
10
9
RTN
Jumper
wires
+
–
Shield ground
IN-0
2
1
i RTN-0
IN-1
4
3
i RTN-1
IN-2
6
5
i RTN-2
IN-3
8
7
i RTN-3
RTN
10
9
RTN
IN-4
12
11
i RTN-4
IN-5
14
13
i RTN-5
IN-6
16
15
i RTN-6
IN-4
12 11
i RTN-4
IN-5
14 13
i RTN-5
IN-6
16 15
i RTN-6
IN-7
18 17
i RTN-7
Not used
20 19
Not used
IN-7
18
17
i RTN-7
Not used
22 21
Not used
Not used
20
19
Not used
Not used
24 23
Not used
Not used
22
21
Not used
Not used
26 25
Not used
Not used
24
23
Not used
Not used
28 27
Not used
Not used
26
25
Not used
Not used
30 29
Not used
Not used
28
27
Not used
Not used
32 31
Not used
Not used
30
29
Not used
Not used
34 33
Not used
Not used
32
31
Not used
Not used
36 35
Not used
Not used
34
33
Not used
Not used
36
35
Not used
NOTES: 1. All terminals marked RTN are connected internally.
2. For current applications, all terminals marked iRTN must be wired to terminals
marked RTN.
3. A 249Ω current loop resistor is located between IN-x and i RTN-x terminals.
4. Place additional loop devices (e.g. strip chart recorders, etc.) at the A location.
5. Do not connect more than 2 wires to any single terminal.
Channel 1
+
–
Shield ground
NOTES: 1. All terminals marked RTN are connected internally.
2. Terminals marked iRTN are not used for single-ended voltage wiring.
3. Do not connect more than 2 wires to any single terminal.
Publication CIG-WD001B-EN-P - May 2005
7-10
1756 ControlLogix I/O Modules
1756-IG16
2
1
IN-1
6
5
8
7
IN-5
DC power wire
IN-7
1
IN-0
4
3
6
5
IN-1
IN-2
IN-4
DC-3 (-)
GND-3
8
7
IN-3
GND-4
GND-5
GND-6
10 9
IN-4
IN-5
IN-6
GND-7
GND-8
16 15
GND-9
GND-10
GND-11
20 19
GND-12
GND-13
26 25
GND-14
GND-15
30 29
32 31
IN-14
IN-15
GND-15
34 33
Not used
Not used
36 35
Not used
I/O wire
IN-6
10
9
DC-0(+)
DC COM 0
12
DC-7 (-)
11
IN-8
IN-9
14
13
16
15
Jumper bar
(Cut to length)
IN-10
IN-11
5V dc power
2
GND-1
GND-2
3
IN-3
–
DC-0 (-)
Isolat ed
wir ing
GND-0
IN-2
IN-0
4
+
1756-IH16I
Capacitor
0.01µ F typical
(See notes below)
IN-12
IN-13
18
17
IN-14
IN-15
20
Non- isolated
wi ring
19
DC COM 1
DC-1(+)
DC (-)
12 11
14 13
18 17
22 21
24 23
28 27
IN-7
IN-8
DC-0 (+)
DC-3 (+)
DC-7 (+)
IN-9
IN-10
IN-11
IN-12
IN-13
DC (+)
GENERAL NOTES:
1. We recommend you use Belden M 8761 cable where shielded cables are shown.
Daisy chain to other RTBs
2. Do not connect more than two wires to any single terminal.
CE REQUIREMENT NOTES:
1. DC power wire and I/O wire should not exceed 10m (30ft) in length.
2. The 0.01µ F capacitors shown above must be rated for 2000V dc.
NOTES: 1. All terminals with the same name are connected together on the module. For
example, DC (-) can be connected to either terminal marked GND-15.
2. When you use the second GND-15 terminal to daisy chain to other RTBs, always
connect the daisy chain to the terminal directly connected to the supply wire, as
shown in the example above. Do not connect more than 2 wires to any single terminal.
3. If separate power sources are used, do not exceed the specified isolation voltage.
1756-IH16ISOE
Isolated wiring
DC-0 (-)
Source input wiring
DC-6 (-)
Jumper bar
(Part number 97739201)
Non-isolated
wiring
DC (-)
1756-IM16I
Sink input wiring
GND-0
GND-1
GND-2
GND-3
GND-4
GND-5
GND-6
GND-7
GND-8
GND-9
GND-10
GND-11
GND-12
GND-13
GND-14
GND-15
GND-15
Not used
2
1
4
3
6
5
8
7
10 9
12 11
14 13
16 15
18 17
20 19
22 21
24 23
26 25
28 27
30 29
32 31
34 33
36 35
IN-0
DC-0 (+)
IN-1
IN-2
IN-3
IN-4
Source input wiring
IN-5
IN-6
DC-6 (+)
IN-7
IN-8
IN-9
IN-10
IN-11
Sink input wiring
IN-12
IN-13
IN-14
IN-15
Not used
Not used
DC (+)
Daisy chain to other RTBs
NOTES:
1. All terminals with the same name are connected together on the module. For
example, DC (-) can be connected to either terminal marked GND-15.
2. When you use the second GND-15 terminal to daisy chain to other RTBs, always
connect the daisy chain to the terminal directly connected to the supply wire, as
shown in the example above.
3. If separate power sources are used, do not exceed the specified isolation voltage.
4. Do not connect more than 2 wires to any single terminal.
5. The jumper bar is part number 97739201; use this number to order additional bars.
Publication CIG-WD001B-EN-P - May 2005
Is olate d wiri ng
L2-0
L2-2
L2-4
Jumper bar
(Cut to length)
Non-isol ated
wir ing
L2
L2-0
2
1
IN-0
L2-1
4
3
IN-1
L2-2
6
5
IN-2
L2-3
8
7
IN-3
L2-4
10
9
IN-4
L2-5
12 11
IN-5
L2-6
14 13
IN-6
L2-7
16 15
IN-7
L2-8
18 17
IN-8
L2-9
20 19
IN-9
L2-10
22 21
IN-10
L2-11
24 23
IN-11
L2-12
26 25
IN-12
L2-13
L2-14
28 27
30 29
IN-13
IN-14
L2-15
32 31
IN-15
L2-15
Not used
34 33
Not used
Not used
36 35
L1-0
L1-2
L1-4
L1
Daisy chain to other RTBs
NOTES: 1. All terminals with the same name are connected together on the module. For
example, L2 can be connected to either terminal marked L2-15.
2. When you use the second L2-15 terminal to daisy chain to other RTBs, always
connect the daisy chain to the terminal directly connected to the supply wire, as
shown in the example above. Do not connect more than 2 wires to any single terminal.
3. If separate power sources are used, do not exceed the specified isolation voltage.
1756 ControlLogix I/O Modules
1756-IN16
1756-IR6I – 2 or 3-Wire RTD
2
2
1
4
3
6
5
8
7
IN-1
IN-3
IN-5
10
9
14
IN-8
RTN-3/C
IN-10
Not used
13
IN-11
16
15
18
17
IN-13
IN-12
IN-15
Group 1
20
8
7
IN-0/B
RTN-0/C
3-Wire RTD
IN-2/A
10
9
12
11
IN-2/B
14
13
16
15
18
17
20
19
Not used
IN-4/A
IN-5/B
19
L2-1
Shield Ground
RTN-2/C
IN-5/A
IN-14
L2-1
5
IN-3/B
11
IN-9
6
IN-3/A
L2-0
12
Group 1
Group 0
IN-6
L2-0
3
RTN-1/C
IN-4
IN-7
IN-0/A
4
IN-1/B
IN-2
Group 0
L2
1
IN-1/A
IN-0
L1
7-11
IN-4/B
RTN-5/C
2-Wire RTD
RTN-4/C
Daisy chain to other RTBs
NOTES:
1. All terminals with the same name are connected together on the module.For example,
L2 can be connected to any terminal marked L2-0.
2. When you daisy chain from a group to another RTB, always connect the daisy chain to
the terminal directly connected to the supply wire, as shown above.
3. This wiring example shows a s ingle voltage source.
4. If separate power sources are used, do n ot exceed the specified isolation voltage.
5. Do not connect more than 2 wires to any single terminal.
NOTES: 1. For 2-wire resistor applications, including calibration, make sure IN-x/B and
RTN-x/C are shorted together. The example above shows IN-4/B and RTN-4/C
shorted together.
2. Do not connect more than 2 wires to any single terminal.
1756-IR6I – 4-Wire RTD
2
1756-IT6I
1
IN-1/A
4
Co ld
junc tion
sensor
5
RTN-1/C
RTN-0/C
8
4-Wire RTD
7
IN-3/A
9
12
11
IN-3/B
6
5
8
7
10
9
Not used
Lug
RTN-0
Shield Ground
12
11
14
13
16
15
18
17
RTN-2
Not used
CJC-
14
13
Not used
Not used
Wire
16
IN-4/A
18
RTN-5/C
20
IN-4/B
20
Not used
Not used
17
IN-5/B
IN-4
IN-5
15
IN-5/A
RTN-5
Thermocouple
Not used
RTN-3
RTN-2/C
–
IN-2
IN-3
CJC+
IN-2/B
RTN-3/C
3
RTN-1
IN-2/A
10
4
Not used
IN-0/B
6
IN-0
IN-0
3
IN-1/B
+
1
2
IN-0/A
19
RTN-4
19
RTN-4/C
NOTES: 1. Wiring is exactly the same as the 3-wire RTD with one wire left open.
2. Do not connect more than 2 wires to any single terminal.
NOTES: 1. If separate power sources are used, do not exceed the specified
isolation voltage.
2. Do not connect more than 2 wires to any single terminal.
3. The part number for the cold junction sensor used on the
1756-IT6I module is 94238301.
Publication CIG-WD001B-EN-P - May 2005
7-12
1756 ControlLogix I/O Modules
1756-IT6I2
1756-IV16
Cold junction sensor
Wire
Spade Lug
2
1
Not used
3
6
5
CJC–
CJC+
RTN-0
6
5
Group 0
IN-4
IN-5
Thermocouple
+
8
7
10
9
12
11
14
13
16
15
18
17
20
19
IN-6
IN-7
DC-0 +
DC-0 +
IN-1
IN-8
IN-9
9
RTN-2
IN-2
12
3
IN-2
Group 0
7
RTN-1
10
4
IN-0
IN-0
8
1
IN-3
Not used
4
2
IN-1
RTN-3
Group 1
IN-3
14
13
16
15
18
17
20
19
IN-10
IN-11
–
11
RTN-4
CJC–
IN-14
DC-1 +
IN-5
Group 1
IN-12
IN-15
IN-4
RTN-5
IN-13
DC-1 +
CJC+
+
Not used
–
DC COM
Not used
Daisy chain to other RTBs
Wire
Cold junction
sensor
Spade Lug
NOTES:
1. Do not connect more than 2 wires to any single terminal.
2. The part number for the cold junction sensor used on the
1756-IT6I2 module is 94286501.
1756-IV32
Group 0
Daisy
chain to
other
RTBs
Jumper
wire
Group 1
NOTES: 1. All terminals with the same name are connected together on the module. For example, DC
(+) can be connected to either terminal marked DC-1+. If you are daisy chain wiring from
one of these terminals to other RTBs, only connect wiring to one terminal.
2. When you daisy chain from a group to another RTB, always connect the daisy chain to the
terminal directly connected to the supply wire, as shown above. Do not connect more than
2 wires to any single terminal.
3. This wiring example shows a single voltage source.
4. If separate power sources are used, do not exceed the specified isolation voltage.
1756-MO2AE – Wiring to a Servo Module RTB
IN-1
2
1
IN-0
IN-3
4
3
IN-2
IN-5
6
5
IN-4
IN-7
8
7
IN-6
IN-9
10
9
IN-8
IN-11
12 11
IN-10
IN-13
14 13
IN-12
IN-15
16 15
IN-14
6
5
8
7
10
9
12
11
14
13
16
15
-ENABLE-1
IN-16
REG24V-0
IN-18
REG5V-0
IN-21
24 23
IN-20
IN-23
26 25
IN-22
IN-25
28 27
IN-24
IN-27
30 29
IN-26
IN-29
32 31
IN-28
–
DC COM
1. All terminals with the same name are connected together on the module. For example,
DC (+) can be connected to either terminal marked DC-1 (+).
2. Do not physically connect more than two wires to a single RTB terminal. When
jumpering I/O groups together and daisy chain wiring to adjacent modules, follow the
wiring method shown above.
3. This wiring example shows a single voltage source.
4. If separate power sources are used, do not exceed the specified isolation voltage.
Publication CIG-WD001B-EN-P - May 2005
18
17
20
19
REG24V-1
To home
limit switch
General Cable
C0720
To registration
sensor
REG5V-1
22
21
24
23
26
25
28
27
30
29
32
31
34
33
36
35
-OK
CHASSIS
+CHA-1
+CHA-0
DC-1 (+)
36 35
General Cable
C0720
HOME-1
+OK
IN-30
34 33
IN_COM
CHASSIS
Group 1
To servo drive
CHASSIS
HOME-0
22 21
General Cable
C0721
DRVFLT-1
IN_COM
20 19
To servo drive
+ENABLE-1
CHASSIS
IN-17
IN-19
General Cable
C0720
-OUT-1
DRVFLT-0
-CHA-0
-CHA-1
+CHB-0
+CHB-1
-CHB-0
General Cable
C0722
To encoder
General Cable
C0720
To E-stop relay coil
-CHB-1
+CHZ-1
+CHZ-0
-CHZ-0
NOTES:
+OUT-1
-ENABLE-0
DC-0 (+)
+
3
+ENABLE-0
Group 0
18 17
DC-1 (+)
1
4
-OUT-0
DC-0 (+)
IN-31
2
+OUT-0
-CHZ-1
This is a general wiring example illustrating Axis 1 wiring only. Other
configurations are possible with Axis 0 wiring identical to Axis 1.
1756 ControlLogix I/O Modules
1756-MO2AE – Wiring to 1394 Servo Drive (in Torque Mode only)
1756-MO2AE – Wiring to an Ultra 100 Series Drive
J1 to 50-pin
Terminal Block
(Kit P/N 9109-1391)
Servo Module RTB
+OUT 1
-OUT 1
+ENABLE 1
-ENABLE 1
DRVFLT 1
CHASSIS
IN_COM
HOME 1
REG24V 1
REG5V 1
-OK
CHASSIS
+CHA 1
-CHA 1
+CHB 1
-CHB 1
+CHZ 1
-CHZ 1
+OUT 0
-OUT 0
+ENABLE 0
-ENABLE 0
DRVFLT 0
CHASSIS
IN_COM
HOME 0
REG24V 0
REG5V 0
+OK
CHASSIS
+CHA 0
-CHA 0
+CHB 0
-CHB 0
+CHZ 0
-CHZ 0
RED
BLK
WHT
BLK
RED
BLK
A
General Cable
C0720
From
1756-M02AE
+5V DC
+5 COM
To fault
string
General Cable
C0721
From
1756-M02AE
24VDC
24VDC
READY+
24VCOM
24VCOM
+OUT
J1-22 COMMAND+
-OUT
J1-23 COMMAND-
P/N 9109-1369-003
-ENABLE
J1-20 ENABLE
DRVFLT
J1-25 READY-
Interface
Cable
J1
IN_COM
ENC. PWR -1
1394 Ser vo Drive
24V DC
24V DC
Field Power
Supply
ENA/DR OK 1
J1-5
J1-26
J1-24
J1-6
J1-13
+ENABLE
RED OK+
BLK OK-
RED
BLK
24 VCOM
Ultra 100 Series
Digital Servo Drive
1394CCAExx
WHT
BLK
RED
BLK
GRN
BLK
OK
5V DC
Field Power
Supply
24 VDC
24 VDC
Field Power Supply
1756-M02AE
7-13
24V COM
WHT
BLK
RED
BLK
+ENABLE 1
-ENABLE 1
DRVFLT 1
IN_COM
W2 24V DC
General Cable
C0722
From
1756-M02AE
W1 24V COM
TB2 15
24V ENABLE COM
TB2 7 A1 ENABLE
TB2 19 DROK
TB2 18 DROK
+CHA
J1-7 AOUT+
-CHA
J1-8 AOUT-
+CHB
J1-9 BOUT+
-CHB
J1-10 BOUT-
+CHZ
J1-11 IOUT+
-CHZ
J1-12 IOUT-
This is general wiring example only. Other configurations are possible. For more information, refer to the
Ultra 100 series installation manual, publication number 1398-5.2.
A
NOTES:
1394CCAExx
Axis 1
AQB1
1. The wiring diagram illustrates Axis 1 wiring only. Other configurations are possible.
2. The 1394-CCAExx cable is wired to connect to torque command reference input pins.
3. An external +5V power supply is required to power the encoder driver circuit of the
1394 servo drive.Because this connection is shared by all four axis encoder driver circuits,
only one connection is needed to the +5V field supply.
4. The xx in the cable number is the length of the cable. Options are 5, 10, 25 and 50 feet.
1756-MO2AE – Wiring to an Ultra 200 Series Drive
J1 to 50-pin
Terminal Block
(Kit P/N 9109-1391)
Ultra 200 Series
Digital Servo Drive
J1-5 24VDC
J1-24 READY+
J1-6 or 13 24VCOM
From
1756-M02AE
General Cable
C0720
+OUT
J1-22 COMMAND+
-OUT
J1-23 COMMAND-
P/N 9109-1369-003
+ENABLE
From
1756-M02AE
General Cable
C0721
-ENABLE
J1-20 ENABLE
DRVFLT
J1-25 READY-
Interface
Cable
J1
IN_COM
From
1756-M02AE
General Cable
C0722
+CHA
J1-7 AOUT+
-CHA
J1-8 AOUT-
+CHB
J1-9 BOUT+
-CHB
J1-10 BOUT-
+CHZ
J1-11 IOUT+
-CHZ
J1-12 IOUT-
This is general wiring example only. Other configurations are possible. For more information, refer to the
Ultra 200 series installation manual, publication number 1398-5.0.
Publication CIG-WD001B-EN-P - May 2005
7-14
1756 ControlLogix I/O Modules
1756-MO2AE – Wiring 24V Registration Sensors
24 VDC
Field Power
Supply
+
-
1756-MO2AE – Wiring 5V Registration Sensors
5 VDC
Field Power
Supply
24 V olt
Sourcing Type
Registration
Sensor
5 Volt
Sourcing Type
Registration
Sensor
+ -
Supply
Supply
From
1756-M02AE
General Cable
C0720
REG24V
Output
IN_COM
Common
General Cable
C0720
From
1756-M02AE
REG5V
Output
IN_COM
Common
The registration inputs to the servo module support 24V or 5V registration sensors. These inputs must be wired to
receive source current from the sensor. Only use sourcing type registration sensors.
1756-MO2AE – Wiring Home Limit Switch Input
1756-MO2AE – Wiring OK Contacts
24 VDC
Field Power
Supply
24 VDC
Field Power
Supply
+
-
+
-
OK Relay
From 1756-M02AE
General Cable
C0720
HOME
From 1756-M02AE
+OK
General Cable
C0720
-OK
IN_COM
The home limit switch inputs to the servo module are designed for 24V nominal operation.
These inputs should be wired for current sourcing operation.
+
24 VDC
Field Power
Supply
OK Relay
Contacts
+OK
Start
-OK
CR1
-
Stop
CR1
CR1
To User's circuitry
M1
When the OK Relay is loaded with an inductive load, use a counter-EMF suppression diode across the load.
The maximum rating of the OK relay contacts must not exceed 60V dc.
1756-M08SE and 1756-M16SE
Receiv er
Transmitter
Fiber optic connectors
Publication CIG-WD001B-EN-P - May 2005
1756 ControlLogix I/O Modules
1756-OA16
2
1756-OA16I
Is olate d wiri ng
1
OUT-1
OUT-0
4
Group 0
OUT-2
6
5
OUT-5
OUT-4
L1-2
Group 0
L1-4
7
8
OUT-7
OUT-6
10
9
12
11
L1-0
L2-0
OUT-9
Jumper bar - Cut to length
(Part number 97739201)
OUT-8
14
13
OUT-11
OUT-10
16
Group 1
L1-0
3
OUT-3
Daisy chain
to other
RTBs
15
OUT-13
OUT-12
18
17
OUT-15
Non-isolated
wiring
Group 1
OUT-14
20
7-15
19
L1-1
L2-1
L1
L1-0
2
1
OUT-0
L1-1
4
3
OUT-1
L1-2
6
5
OUT-2
L1-3
8
7
OUT-3
L1-4
10
9
OUT-4
L1-5
12 11
OUT-5
L1-6
14 13
OUT-6
L1-7
16 15
OUT-7
L1-8
18 17
OUT-8
L1-9
20 19
OUT-9
L1-10
22 21
OUT-10
L1-11
24 23
OUT-11
L1-12
26 25
OUT-12
L1-13
L1-14
28 27
OUT-13
30 29
OUT-14
L1-15
32 31
OUT-15
L1-15
Not used
34 33
Not used
Not used
36 35
L2-0
L2-2
L2-4
L2
L1
Daisy chain to other RTBs
L2
NOTES: 1. This wiring example shows a single voltage source.
2. When you daisy chain from a group to other RTBs, always connect the daisy chain
as shown. Do not connect more than 2 wires to any single terminal at any time.
NOTES: 1. All terminals with the same name are connected together on the module. For
example, L1 can be connected to either terminal marked L1-15.
2. When you use the second L1-15 terminal to daisy chain to other RTBs, always
connect the daisy chain to the terminal directly connected to the supply wire, as
shown in the example above. Do not connect more than 2 wires to any single terminal.
1756-OA8
2
1
OUT-0
L1-0
4
OUT-1
6
5
8
7
10
9
12
11
14
13
16
15
Daisy
chain to
other
RTBs
OUT-5
L1-1
Group 1
OUT-6
L1-1
18
OUT-7
20
L1-1
7
10
9
12
11
14
13
16
15
18
17
20
19
OUT-1
OUT-3
OUT-4
L1-1
OUT-5
L1-1
OUT-6
L1-1
L2
L1-1
Group 0
OUT-2
L1-1
19
Not used
8
OUT-0
L1-0
Group 1
17
L1-1
5
L1-0
OUT-4
L1-1
6
L2-0
L1-0
Not used
L1-0
Group 1
Group 0
Group 0
OUT-3
L1-0
1
3
L1-0
OUT-2
L1-0
2
4
Not used
3
L1-0
Group 0
1756-OA8D
Group 1
OUT-7
L2-1
L2
Daisy chain to other RTBs
Daisy chain to other RTBs
L1
L1
NOTES: 1. All terminals with the same name are connected together on the module. For
example, L1 can be connected to any terminal marked L1-0.
2. When you daisy chain from a group to another RTB, always connect the daisy chain
to the terminal directly connected to the supply wire, as shown above.
Do not connect more than 2 wires to any single terminal.
3. This wiring example shows a single voltage source.
NOTES: 1. All terminals with the same name are connected together on the module.
For example, L1 can be connected to any terminal marked L1-0.
2. When you daisy chain from a group to another RTB, always connect the daisy chain
to the terminal directly connected to the supply wire, as shown above.
Do not connect more than 2 wires to any single terminal.
3. This wiring example shows a single voltage source.
Publication CIG-WD001B-EN-P - May 2005
7-16
1756 ControlLogix I/O Modules
1756-OA8E
2
Daisy chain to other RTBs
1
L2-0
Not used
4
3
OUT-0
L1-0
6
5
L1-0
Group 0
OUT-1
8
Group 0
OUT-2
10
9
12
11
L1-0
OUT-3
OUT-4
L1-1
14
13
L1-1
OUT-5
16
15
OUT-6
L1-1
18
17
OUT-7
L1-1
Group 1
Group 0
7
L1-0
Daisy
chain to
other
RTBs
1756-OB16D
20
Group 1
Group 1
19
L2-1
L1-1
L2
Daisy chain to other RTBs
+DC-0
2
1
OUT-0
+DC-0
4
3
OUT-1
+DC-0
6
5
OUT-2
+DC-0
8
7
OUT-3
+DC-0
10
9
OUT-4
+DC-0
12
11
OUT-5
+DC-0
14
13
OUT-6
GND-0
16
15
OUT-7
+DC-1
18
17
OUT-8
+DC-1
+DC-1
20
19
OUT-9
22
21
OUT-10
+DC-1
24
23
OUT-11
+DC-1
26
25
OUT-12
+DC-1
28
27
OUT-13
+DC-1
30
29
OUT-14
GND-1
32
31
OUT-15
GND-1
34
33
Not used
Not used
36
35
Not used
Group 0
Group 1
Daisy chain to other RTBs
L1
+
NOTES:
1. All terminals with the same name are connected together on the module. For
example, L1 can be connected to any terminal marked L1-0.
2. When you daisy chain from a group to another RTB, always connect the daisy
chain to the terminal directly connected to the supply wire, as shown above.
Do not connect more than 2 wires to any single terminal.
3. This wiring example shows a single voltage source.
2
1
Isol ated sour cing
out put wir ing
Isolat ed wir ing
DC-0 (+)
2
1
OUT-0
DC-1 (+)
4
3
OUT-1
DC-2 (+)
6
5
OUT-2
DC-3 (+)
8
7
OUT-3
DC-4 (+)
10
9
OUT-4
DC-5 (+)
12
11
OUT-5
DC-6 (+)
14
13
OUT-6
DC-7 (+)
16
15
OUT-7
Jumper bar - Cut to length
DC-8 (+)
18
17
OUT-8
(Part number 97739201)
DC-9 (+)
20
19
OUT-9
DC-10 (+)
22
21
OUT-10
DC-11 (+)
24
23
OUT-11
DC-12 (+)
26
25
OUT-12
DC-13 (+)
28
27
OUT-13
DC-14 (+)
30
29
OUT-14
DC-15 (+)
32
31
OUT-15
DC-15 (+)
Not used
34
33
36
35
Not used
Not used
DC-0 (+)
3
OUT-3
OUT-2
6
Daisy chain to
other RTBs
1756-OB16I
OUT-0
4
Group 0
Group 0
DC-2 (+)
5
OUT-5
OUT-4
8
7
OUT-7
OUT-6
10
Sin k ing outp ut wir ing
9
DC-6 (+)
DC-0(+)
RTN OUT-0
12
11
14
13
OUT-9
OUT-8
OUT-11
OUT-10
16
15
OUT-13
Non-i solated
wir ing
OUT-12
Group 1
18
17
20
19
Group 1
OUT-15
OUT-14
DC-1(+)
RTN OUT-1
+
DC COM
NOTES 1. All terminals with the same name are connected together on the module. For example,
DC COM can be connected to either terminal marked GND-1.
2. When you daisy chain to other RTBs, always connect the daisy chain to the terminal
directly connected to the supply wire, as shown in the example above.
Do not connect more than 2 wires to any single terminal.
3. This wiring example shows a single voltage source.
4. If separate power sources are used, do not exceed the specified isolation voltage.
1756-OB16E
OUT-1
–
DC(+)
+
–
DC-0 (-)
DC-2 (-)
DC-6 (-)
Non-isol ated
sourc ing
outp ut
wir ing
DC(-)
–
DC COM
NOTES: 1. When you daisy chain from a group to another RTB, always connect the daisy
chain as shown above. Do not connect more than 2 wires to any single terminal.
2. This wiring example shows a single voltage source.
3. If separate power sources are used, do not exceed the specified isolation voltage.
Publication CIG-WD001B-EN-P - May 2005
Daisy chain to other RTBs
NOTES:1. All terminals with the same name are connected together on the module. For
example, DC (+) can be connected to either terminal marked DC-15.
2. When you use the second DC-15 (+) terminal to daisy chain to other RTBs, always
connect the daisy chain to the terminal directly connected to the supply wire, as
shown in the example above. Do not connect more than 2 wires to any single terminal.
3. Outputs can be wired in a sink or source configuration as shown above.
4. If separate power sources are used, do not exceed the specified isolation voltages.
1756 ControlLogix I/O Modules
1756-OB16IS
1756-OB32
Isolated wiring
DC-0 (+)
DC-1 (+)
DC-2 (+)
DC-2 (+)
DC-3 (+)
DC-4 (+)
Sinking output wiring DC-5 (+)
DC-6 (+)
DC-6 (+)
+
–
DC-7 (+)
Jumper bar
DC-8 (+)
(Cut to length)
DC-9 (+)
DC-10 (+)
DC-11 (+)
Non-isolated
DC-12 (+)
wiring
DC-13 (+)
DC-14 (+)
DC-15 (+)
DC(+)
DC-15 (+)
Not used
DC-0 (+)
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
20
19
22
21
24
23
26
25
28
27
30
29
32
31
34
33
36
35
7-17
OUT-0
OUT-1
OUT-2
OUT-3
OUT-4
OUT-5
OUT-6
OUT-7
OUT-8
OUT-9
OUT-10
OUT-11
OUT-12
OUT-13
OUT-14
OUT-15
Isolated sourcing
output wiring
DC-0 (-)
DC-2 (-)
Group 0
Daisy chain
to other
RTBs
DC-6 (-)
Non-isolated
sourcing
output
wiring
Group 1
Not used
Not used
OUT-1
OUT-3
OUT-5
2
1
4
3
6
5
OUT-7
OUT-9
OUT-11
8
7
10
9
OUT-0
OUT-2
OUT-4
OUT-6
OUT-8
OUT-10
12 11
OUT-13
OUT-15
DC-0(+)
14 13
OUT-17
OUT-19
OUT-21
20 19
OUT-23
OUT-25
OUT-27
26 25
OUT-29
OUT-31
DC-1(+)
32 31
Group 0
OUT-12
OUT-14
RTN OUT-0
16 15
18 17
OUT-16
OUT-18
OUT-20
OUT-22
OUT-24
OUT-26
22 21
24 23
28 27
30 29
Group 1
OUT-28
OUT-30
RTN OUT-1
34 33
36 35
DC(-)
_
+
Daisy chain to other RTBs
NOTES: 1. All terminals with the same name are connected together on the module. For
example, DC (+) can be connected to either terminal marked DC-15.
2. When you use the second DC-15 (+) terminal to daisy chain to other RTBs, always
connect the daisy chain as shown in the example above. Do not connect more than
2 wires to any single terminal.
3. Outputs can be wired in a sink or source configuration as shown above.
4. If separate power sources are used, do not exceed the specified isolation voltages.
DC COM
NOTES: 1. When you daisy chain from a group to another RTB, always connect the daisy
chain as shown above. Do not connect more than 2 wires to any single terminal.
2. This wiring example uses a single voltage source.
3. If separate power sources are used, do not exceed the specified isolation voltage.
1756-OB8
1756-OB8EI
Daisy chain to other RTBs
2
+
1
DC-0 (+)
OUT-0
4
Group 0
3
DC-0 (+)
OUT-1
6
Group 0
5
DC-0 (+)
+
OUT-2
8
-
Isolated
Wi ring
-
7
DC-0 (+)
OUT-3
10
Non -Isolat ed
Wi ri ng
RTN OUT-0
11
DC-1 (+)
OUT-4
14
13
16
15
DC-1 (+)
OUT-5
Group 1
Group 1
DC-1 (+)
OUT-6
18
17
20
19
DC-1 (+)
Daisy
chain to
other
RTBs
OUT-7
RTN OUT-1
RTN OUT-1
Daisy chain to other RTBs
+
2
1
OUT-0
4
3
OUT-0
DC-1 (+)
6
5
OUT-1
RTN OUT-1
8
7
OUT-1
DC-2 (+)
10
9
OUT-2
RTN OUT-2
12
11
OUT-2
DC-3 (+)
14
13
OUT-3
RTN OUT-3
16
15
OUT-3
DC-4 (+)
18
17
OUT-4
RTN OUT-4
DC-5 (+)
20
19
22
21
OUT-4
OUT-5
RTN OUT-5
24
23
OUT-5
DC-6 (+)
26
25
OUT-6
RTN OUT-6
28
27
OUT-6
DC-7 (+)
30
29
OUT-7
RTN OUT-7
32
31
OUT-7
Not used
34
33
Not used
Not used
36
35
Not used
9
RTN OUT-0
12
DC-0 (+)
RTN OUT-0
Daisy
chain to
other
RTBs
+
–
DC COM
–
DC COM
NOTES: 1. All terminals with the same name are connected on the module. For example, DC
COM can be connected to either terminal marked RTN OUT-1.
2. When you daisy chain from a group to another RTB, always connect the daisy
chain to the terminal directly connected to the supply wire, as shown.
Do not connect more than 2 wires to any single terminal.
3. This wiring example shows a single voltage source.
4. If separate power sources are used, do not exceed the specified isolation voltage.
NOTES 1. All terminals with the same name are connected together on the module. For example,
the load can be connected to either terminal marked OUT-0.
2. When you daisy chain to other RTBs, always connect the daisy chain to the terminal
directly connected to the supply wire, as shown in the example above.
Do not connect more than 2 wires to any single terminal.
3. If separate power sources are used, do not exceed the specified isolation voltage.
Publication CIG-WD001B-EN-P - May 2005
7-18
1756 ControlLogix I/O Modules
1756-OC8
1756-OF4 – Current Applications
Daisy chain to other RTBs
2
1
4
3
DC-0 (+)
OUT-0
DC-0 (+)
OUT-1
Group 0
6
13
Group 1
15
DC-1(+)
11
14
13
16
15
DC-1(+)
18
17
20
19
Not used
IOUT-2
RTN
OUT-7
RTN OUT-1
RTN
Not used
RTN OUT-1
Shield ground
VOUT-2
OUT-6
19
12
IOUT-1
OUT-5
20
9
Not used
DC-1(+)
17
10
VOUT-1
OUT-4
18
7
Not used
11
DC-1(+)
16
8
Current
output
load
A
RTN
RTN OUT-0
Group 1
5
Not used
9
RTN OUT-0
14
6
i
IOUT-0
OUT-3
12
3
RTN
7
DC-0 (+)
10
4
VOUT-0
OUT-2
8
1
Not used
Group 0
5
DC-0 (+)
2
Not used
VOUT-3
Not used
IOUT-3
Daisy chain to other RTBs
–
+
DC COM
NOTES:
1. All terminals with the same name are connected together on the module.
For example, DC COM can be connected to either terminal marked RTN OUT-1.
2. When you daisy chain from a group to another RTB, always connect the daisy
chain to the terminal directly connected to the supply wire, as shown above.
Do not connect more than 2 wires to any single terminal.
NOTES: 1. Place additional loop devices (e.g strip chart recorders) at the A location shown above.
2. Do not connect more than 2 wires to any single terminal.
3. All RTN terminals are connected internally.
3. This wiring example shows a single voltage source.
4. If separate power sources are used, do not exceed the specified isolation voltage.
1756-OF4 – Voltage Applications
2
2
3
Not used
6
RTN
7
10
9
12
11
14
13
Not used
IOUT-1
Not used
VOUT-2
Not used
IOUT-2
16
RTN
18
17
20
19
Not used
VOUT-3
IOUT-3
NOTES: 1. Do not connect more than 2 wires to any single terminal.
2. All RTN terminals are connected internally.
Publication CIG-WD001B-EN-P - May 2005
5
8
7
10
9
12
11
14
13
OUT-2
ALT-2
RTN-3
RTN-2
Not used
Not used
16
15
18
17
20
19
OUT-5
OUT-4
ALT-5
RTN-5
NOTES:
User Analog
Output Device
RTN-0
ALT-3
15
RTN
6
OUT-3
Shield ground
i
ALT-0
RTN-1
VOUT-1
Not used
3
ALT-1
–
5
8
OUT-0
4
IOUT-0
RTN
1
OUT-1
VOUT-0
4
Not used
+
1
Not used
1756-OF6CI – 0 - 550Ω Applications
ALT-4
RTN-4
1. Place additional devices anywhere in the loop.
2. Do not connect more than 2 wires to any single terminal.
Shield
Ground
1756 ControlLogix I/O Modules
1756-OF6VI
1756-OF6CI – 551 - 1000Ω Applications
2
1
OUT-1
2
OUT-0
4
User Analog
Output Device
ALT-0
6
OUT-0
4
RTN-0
8
10
9
12
11
14
13
ALT-3
18
ALT-4
20
12
11
14
13
Not used
RTN-2
16
15
18
17
20
19
OUT-4
Not used
RTN-4
RTN-5
NOTES:
RTN-4
1. Place additional devices anywhere in the loop.
2. Do not connect more than 2 wires to any single terminal.
NO TE S: Do not connect more than 2 wires to any single terminal.
1756-OF8 – Voltage Applications
1756-OF8 – Current Applications
2
2
1
VOUT-0
VOUT-4
4
IOUT-0
6
A
5
RTN
Current
output
load
RTN
8
VOUT-1
10
9
12
11
14
13
16
15
IOUT-6
RTN
18
5
IOUT-0
–
RTN
8
7
10
9
VOUT-1
Shield ground
IOUT-1
12
11
14
13
16
15
18
17
20
19
Not used
VOUT-2
Not used
IOUT-2
RTN
RTN
17
VOUT-7
VOUT-3
20
6
RTN
Shield ground
IOUT-2
RTN
3
Not used
VOUT-2
VOUT-6
4
Not used
IOUT-1
IOUT-5
VOUT-0
Not used
7
VOUT-5
+
1
Not used
i
3
IOUT-4
IOUT-7
Shield Ground
Not used
Not used
19
RTN-5
9
OUT-5
17
ALT-5
10
Not used
OUT-4
–
OUT-2
RTN-3
15
OUT-5
7
RTN-0
Shield Ground
Not used
16
8
Not used
RTN-2
Not used
5
OUT-3
ALT-2
RTN-3
6
RTN-1
OUT-2
User Analog
Output Device
Not used
7
OUT-3
3
Not used
5
RTN-1
+
1
OUT-1
i
3
ALT-1
7-19
Not used
VOUT-3
19
IOUT-3
NOTES: 1. Place additional loop devices (e.g strip chart recorders) at the A
location shown above.
2. Do not connect more than 2 wires to any single terminal.
3. All RTN terminals are connected internally.
Not used
IOUT-3
NOTES: 1. Do not connect more than 2 wires to any single terminal.
2. All RTN terminals are connected internally.
Publication CIG-WD001B-EN-P - May 2005
7-20
1756 ControlLogix I/O Modules
1756-OG16
1756-OH8I
Isol ated W iri ng
DC power wire
+
5V dc
power
2
–
OUT-0
4
OUT-2
6
5
OUT-5
8
7
10
9
12
11
DC COM 0
OUT-9
OUT-8
14
13
16
15
OUT-11
Capacitor
0.01µ F typical
(See notes below)
-
OUT-6
DC-0(+)
–
+
OUT-4
OUT-7
I/O wire
-
3
OUT-3
+
+
1
OUT-1
Non-Isol ated
Wi ri ng
OUT-10
OUT-13
OUT-12
18
17
OUT-15
OUT-14
20
DC-1(+)
19
Daisy
chain to
other
RTBs
DC COM 1
GENERAL NOTES:
1. We recommend you use Belden M 8761 cable where shielded
cables are shown.
2. Do not connect more than two wires to any single terminal.
CE REQUIREMENT NOTES:
1. DC power wire and I/O wire should not exceed 10m (30ft) in length.
2. The 0.01µ F capacitors shown must be rated for 2000V dc.
Daisy
chain to
other
RTBs
DC-0 (+)
2
1
OUT-0
RTN OUT-0
4
3
OUT-0
DC-1 (+)
6
5
OUT-1
RTN OUT-1
DC-2 (+)
8
7
10
9
OUT-1
OUT-2
RTN OUT-2
12
11
OUT-2
DC-3 (+)
14
13
OUT-3
RTN OUT-3
16
15
OUT-3
DC-4 (+)
18
17
OUT-4
RTN OUT-4
20
19
OUT-4
DC-5 (+)
22
21
OUT-5
RTN OUT-5
24
23
OUT-5
DC-6 (+)
26
25
OUT-6
RTN OUT-6
28
27
OUT-6
DC-7 (+)
30
29
OUT-7
RTN OUT-7
32
31
OUT-7
Not used
34
33
Not used
Not used
36
35
Not used
+
NOTES
1. All terminals with the same name are connected together on the module. For example, the
load can be connected to either terminal marked OUT-0.
2. When you daisy chain to other RTBs, always connect the daisy chain to the terminal directly
connected to the supply wire, as shown in the example above. Do not connect more than 2
wires to any single terminal.
3. If separate power sources are used, do not exceed the specified isolation voltage.
1756-ON8
1756-OV16E
Daisy chain to other RTBs
2
4
Group 0
OUT-1
5
8
7
10
9
12
11
L1-0
OUT-2
L1-0
14
18
17
L1-1
8
7
10
9
12
11
14
13
16
15
18
17
OUT-4
OUT-5
RTN OUT-0
OUT-8
OUT-9
OUT-10
OUT-11
Group 1
Group 1
Group 0
OUT-6
OUT-12
OUT-13
Group 1
OUT-14
OUT-15
20
OUT-6
L1-1
5
DC-0(+)
OUT-5
15
6
OUT-7
13
16
3
OUT-2
OUT-4
L1-1
19
RTN OUT-1
DC-1(+)
OUT-7
20
L1-1
Group 0
Not used
L1-1
Group 1
Group 0
OUT-3
L1-0
4
OUT-3
3
6
1
OUT-0
OUT-0
L1-0
2
OUT-1
1
L1-0
– DC COM
19
Not used
L2
+
–
DC COM
L1
NOTES: 1. All terminals with the same name are connected together on the module. For
example, L1 can be connected to any terminal marked L1-1.
2. When you daisy chain from a group to another RTB, always connect the daisy
chain to the terminal directly connected to the supply wire, as shown above.
Do not connect more than 2 wires to any single terminal.
3. This wiring example shows a single voltage source.
Publication CIG-WD001B-EN-P - May 2005
Daisy chain to other RTBs
Daisy chain to other RTBs
NOTES: 1. When you daisy chain from a group to another RTB, always connect the daisy chain to
the terminal directly connected to the supply wire, as shown above.
Do not connect more than 2 wires to any single terminal.
2. This wiring example shows a single voltage source.
3. If separate power sources are used, do not exceed the specified isolation voltage.
1756 ControlLogix I/O Modules
1756-OW16I
1756-OV32E
Isol ated w iring
L1-0
L1-0
L1-1
L1-2
L1-2
L1-3
DC-4 (+)
L1-4
L1-5
L1-6
Jumper bar - Cut to length L1-7
(Part number 97739201) L1-8
L1-9
L1-10
L1-11
Non -isol ated
L1-12
wi ring
L1-13
L1-14
L1-15
L1-15
L1
Not used
2
1
4
3
6
5
8
7
10
9
12 11
14 13
16 15
18 17
20 19
22 21
24 23
26 25
28 27
30 29
32 31
34 33
36 35
L2-0
OUT-0
OUT-1 N.O.
OUT-2 N.O.
OUT-3 N.O.
OUT-4 N.O.
OUT-5 N.O.
OUT-6 N.O.
OUT-7 N.O.
OUT-8 N.O.
OUT-9 N.O.
OUT-10 N.O.
OUT-11 N.O.
OUT-12 N.O.
OUT-13 N.O.
OUT-14 N.O.
OUT-15 N.O
Not used
Not used
Daisy chain to
other RTBs
L2-2
DC-4 (-)
Group 0
Group 1
L2
Daisy chain to
other RTBs
OUT-1
OUT-3
OUT-5
2
1
4
3
6
5
OUT-7
OUT-9
OUT-11
8
7
10
9
14 13
OUT-17
OUT-19
OUT-21
20 19
OUT-23
OUT-25
OUT-27
26 25
OUT-29
OUT-31
DC-1(+)
32 31
24 23
4
3
6
5
8
7
10
9
12 11
14 13
16 15
18 17
20 19
22 21
24 23
26 25
28 27
30 29
32 31
34 33
36 35
OUT-22
OUT-24
OUT-26
28 27
30 29
Group 1
OUT-28
OUT-30
RTN OUT-1
34 33
36 35
_
DC COM
NOTES: 1. When you daisy chain from a group to another RTB, always connect the daisy
chain to the terminal directly connected to the supply wire, as shown above.
2. This wiring example uses a single voltage source.
3. If separate power sources are used, do not exceed the specified isolation voltage
4. Do not physically connect more than two wires to a single RTB terminal.
Isol ated wi ring
1
OUT-16
OUT-18
OUT-20
22 21
1756-OX8I
Isol ated w iring
2
Group 0
OUT-12
OUT-14
RTN OUT-0
18 17
1756-OW16I
L1-0
L1-1
L1-2
L1-2
L1-3
DC-4 (+)
L1-4
L1-5
L1-6
Jumper bar - Cut to length L1-7
(Part number 97739201) L1-8
L1-9
L1-10
L1-11
Non -isol ated
L1-12
wi ring
L1-13
L1-14
L1-15
L1-15
L1
Not used
OUT-6
OUT-8
OUT-10
16 15
+
NOTES: 1. All terminals with the same name are connected together on the module. For
example, L1 can be connected to either terminal marked L1-15.
2. When daisy chaining the second L1-15 terminal to other RTBs, always connect the
daisy chain to the terminal directly connected to the supply wire, as shown in the
example above. Do not connect more than 2 wires to any single terminal.
3. If separate power sources are used, do not exceed the specified isolation voltage.
OUT-0
OUT-2
OUT-4
12 11
OUT-13
OUT-15
DC-0(+)
Daisy chain to other RTBs
L1-0
7-21
L2-0
OUT-0
OUT-1 N.O.
OUT-2 N.O.
OUT-3 N.O.
OUT-4 N.O.
OUT-5 N.O.
OUT-6 N.O.
OUT-7 N.O.
OUT-8 N.O.
OUT-9 N.O.
OUT-10 N.O.
OUT-11 N.O.
OUT-12 N.O.
OUT-13 N.O.
OUT-14 N.O.
OUT-15 N.O
Not used
Not used
L1-0
OUT-0 N.C.
3
OUT-0 N.O.
6
5
L1-1
8
7
OUT-1 N.O.
L1-2
10
9
OUT-2 N.C.
L1-2
12 11
OUT-2 N.O.
L1-3
14 13
OUT-3 N.C.
L1-3
16 15
OUT-3 N.O.
L1-4
18 17
OUT-4 N.C.
L1-4
20 19
OUT-4 N.O.
L1-5
22 21
OUT-5 N.C.
L1-5
24 23
OUT-5 N.O.
L1-6
26 25
OUT-6 N.C.
L1-6
28 27
OUT-6 N.O.
L1-7
30 29
OUT-7 N.C.
L1-7
32 31
OUT-7 N.O
L1-7
34 33
Not used
Not used
36 35
Not used
Jumper bar - Cut to length
(Part number 97739201)
L1
1
4
OUT-1 N.C.
DC-2 (+)
Non- isolated
wi ring
2
L1-0
L1-1
L2-2
DC-4 (-)
L1-0
NOTES: 1. All terminals with the same name are connected together on the module. For
example, L1 can be connected to either terminal marked L1-15.
2. When daisy chaining the second L1-15 terminal to other RTBs, always connect the
daisy chain to the terminal directly connected to the supply wire, as shown in the
example above. Do not connect more than 2 wires to any single terminal.
3. If separate power sources are used, do not exceed the specified isolation voltage.
DC-2 (-)
L2
L2
Daisy chain to other RTBs
L2-0
Daisy chain to other RTBs
NOTES: 1. All terminals with the same name are connected together on the module. For
example, L1-0 can be connected to either terminal marked L1-0.
2. When you use the third L1-7 terminal to daisy chain to other RTBs, always connect
the daisy chain to the terminal directly connected to the supply wire, as shown in
the example above. Do not connect more than 2 wires to any single terminal.
3. If separate power sources are used, do not exceed the specified isolation voltage.
Publication CIG-WD001B-EN-P - May 2005
7-22
1756 ControlLogix I/O Modules
1756-PLS Resolver Module
2
1
Do not use
Do not use
4
3
6
5
Do not use
Do not use
Do not use
Do not use
Do not use
10
9
Do not use
Do not use
12
11
14
13
Do not use
Do not use
F ( S3)
E (S2)
G (S4)
A
White
R1
B
Black of white
R2
1 4 ( Sine+ )
F
Black of red
S3
16 (S ine-)
D
Red
S1
18 (Cosine+)
E
Green
S2
20 (Cosi ne- )
G
Black of green
S4
17 (Refere nce+)
19 (Reference-)
Do not use
Sine +
D (S1)
Resolver
Signal Name
846-SJxNxCG-R3
846-SAxNxCG-R3
Allen-Bradley Resolvers
Designation
7
8
Do not use
Allen-Brad ley Resolver
846-S JDA1CG-R3-C
845-CA-E-25
845-CA-F-25
Connector Cables
Color Pairs
RTB Terminal
Number
16
15
18
17
20
19
Do not use
Sine –
Reference +
Cosine +
Reference –
Cosine –
A (R1)
B (R2)
NOTE: Do not connect more than 2 wires to any single terminal.
1756-PLS Left Section I/O Module
2
1
OUTPUT 0
4
3
6
5
8
7
10
9
12
11
INPUT 2
OUTPUT 3
INPUT 3
DC PWR 0- 3
+
13
16
15
OUTPUT 5
INPUT 6
18
17
20
19
INPUT 7
OUTPUT 7
6
5
8
7
10
9
12
11
14
13
16
15
18
17
20
19
INPUT 8
INPUT 9
INPUT 10
INPUT 11
DC PWR 8- 11
10- 30V dc
DC COM 8-11
OUTPUT 12
INPUT 12
OUTPUT 13
INPUT 5
OUTPUT 6
3
OUTPUT 11
INPUT 4
14
4
OUTPUT 10
_
DC COM 0-3
OUTPUT 4
1
OUTPUT 9
INPUT 1
OUTPUT 2
2
OUTPUT 8
INPUT 0
OUTPUT 1
DC PWR 4- 7
1756-PLS Right Section I/O Module
+
INPUT 13
INPUT 14
OUTPUT 14
OUTPUT 15
_
DC PWR 12- 15
DC COM 4- 7
INPUT 15
DC COM 12-15
+
NOTE: Do not connect more than 2 wires to any single terminal.
_
NOTE: Do not connect more than 2 wires to any single terminal.
Publication CIG-WD001B-EN-P - May 2005
Chapter
8
1761 Controller I/O on
MicroLogix 1000 Controllers
1761-L10BWA
Sinking Input Configuration
Sourcing Input Configuration
14–30V dc
VDC (–)
VDC +
14–30V dc
VDC (+)
DC OU T
DC
CO M
I/0
I/1
I/2
I/3
DC
CO M
I/4
VAC
VDC
O/2 VDC
I/5
VAC
VAC
VDC
L2/N
O/0 VDC
O/1
+ 24V –
NO T NO T NO T NO T
US ED US ED US ED US ED
85–264 VAC
L1
VDC (–)
for Sourcing
VDC (–)
+ 24V –
VDC (+)
VDC (–) for Sourcing
VDC (+)
NO T
VAC
NO T
DC OU T
I/0
I/1
VAC
VDC
L2/N
L1
CR
VAC 2
VDC 1
I/3
DC
CO M
I/4
O/1
VAC
VDC
O/2 VDC
VAC
O/0 VDC
I/5
NO T NO T NO T NO T
US ED US ED US ED US ED
NO T
VAC
VDC 1
VDC 2
VDC 1
CO M
VAC 2
CO M
VAC 1
VAC 1
CO M
NO T
CR
VAC 2
VDC 2
CO M
NO T
O /3 US ED US ED US ED
CR
VDC 2
VDC 1
CO M
VAC 2
CO M
VAC 1
I/2
85–264 VAC
NO T
O /3 US ED US ED US ED
CR
DC
CO M
VDC 2
CO M
VAC 1
CO M
1761-L10BWB
Sinking Input Configuration
Sourcing Input Configuration
14–30 VDC
VDC
Com
NO T
US ED
NO T DC
US ED CO M
DC IN
+ 24V –
14–30 VDC
VDC +
I/0
I/1
I/2
VAC
VDC
O/0 VDC
I/3
DC
CO M
O/1
VAC
VDC
VAC
I/4
I/5 NO T
US ED
1
NO T
NO T
US ED
VDC 2
VAC 1
CO M
VDC (–)
I/0
I/1
I/2
VAC
VDC
O/0 VDC
I/3
DC
CO M
O/1
VAC
VDC
VAC
VDC (–)
I/4
I/5 NO T
US ED
VDC 1
NO T
VAC
O/2 VDC
NO T NO T NO T
US ED US ED US ED
NO T
NO T
O /3 US ED US ED US ED
CR
VAC 1
VDC 3
CO M
VDC (+)
CR
VDC 3
VDC 2
CO M
NO T DC
US ED CO M
DC IN
+ 24V –
NO T
O /3 US ED US ED US ED
CR
VAC 1
VDC 1
CO M
NO T NO T NO T
US ED US ED US ED
NO T
VAC
O/2 VDC
CR
VDC 1
14–30 VDC
14–30 VDC
VDC (+)
VDC VDC +
Com
VDC 2
VAC 1
CO M
VDC 3
VDC 2
CO M
VDC 3
CO M
VDC 1
CO M
Publication CIG-WD001B-EN-P - May 2005
8-2
1761 Controller I/O on MicroLogix 1000 Controllers
1761-L10BXB
24V dc In, 24V dc and Relay Out
Showing sourcing (sink load) configuration of inputs.
+
24V dc In, 24V dc and Relay Out
Showing sinking (source load) configuration of inputs.
+
+
+
NOT
USED
NOT NOT
USED USED
O/1
DC
24V+
O/2
O/3
NOT
USED
NOT DC
NOT
USED 24V– USED
VAC
NOT
USED
NOT
USED
NOT
USED
DC
COM
DC IN
+ 24V –
I/0
I/1
+
I/2
VAC
VDC
O/0 VDC
I/3
DC
COM
I/4
I/5
NOT
USED
NOT NOT
USED USED
O/1
DC
24V+
O/2
O/3
NOT
USED
NOT DC
NOT
USED 24V– USED
VAC
NOT
USED
+
I/5
L2/-dc
I/4
L1/+dc
O/0 VDC
DC
COM
L2/-dc
VAC
VDC
I/3
L2/-dc
+
I/2
L1/+dc
I/1
L1/+dc
DC IN
+ 24V –
I/0
+
DC
COM
L1/+dc
NOT
USED
L2/-dc
NOT
USED
1761-L16AWA
79–132V ac
79–132V ac
L2/N
NO T
US ED
NO T AC
US ED CO M
L1
I/0
I/1
I/2
VAC
VDC
O/0 VDC
L2/N
I/3
AC
CO M
O/1
VAC
VDC
L1
I/4
I/5
I/6
I/7
I/8
I/9
85–264 VAC
L1
L2/N
VAC
VAC
VAC
O/2 VDC
O /3 VDC
O/4
O/5
CR
CR
CR
CR
VAC 2
VDC 1
VAC 2
CO M
VAC 1
VDC 2
VDC 1
CO M
VDC 3
VDC 2
CO M
VDC 3
CO M
VAC 1 CO M
1761-L16BBB
24V dc In, 24V dc and Relay Out
Showing sourcing (sink load) configuration of inputs.
+
+
24V dc In, 24V dc and Relay Out
Showing sinking (source load) configuration of inputs.
+
+
O/1
I/6
I/7
O/3
O/4
O/5
+24V
dc
I/9
Not Not DC
I/0
Used Used COM
-24V
dc
Not
Used
+24V -24V
dc
dc
IN
IN
+
+
O/2
I/8
Publication CIG-WD001B-EN-P - May 2005
VAC
VDC
I/1
I/2
I/3
O/0
VAC
VDC
O/1
DC
I/4
COM
I/5
I/6
I/7
O/3
O/4
O/5
+24V
dc
O/2
+
VAC
VDC
I/5
L2/-dc
O/0
DC
I/4
COM
L2/-dc
L1/+dc
I/3
L1/+dc
I/2
L2/-dc
VAC
VDC
L1/+dc
+
+24V -24V
dc
dc
IN
IN
I/1
L2/-dc
L1/+dc
Not Not DC
I/0
Used Used COM
I/8
I/9
-24V
dc
Not
Used
1761 Controller I/O on MicroLogix 1000 Controllers
8-3
1761-L16BWA
DC
I/0
COM
I/1
I/2
I/3
DC
I/4
COM
200mA max
I/5
I/6
I/7
I/8
I/9
I/2
I/3
DC
I/4
COM
I/5
I/6
I/7
I/8
I/9
VAC
VDC
O/4
O/5
L2/-dc
L1
VAC
VDC
L2/N
O/0
VAC
VDC
0/1
VAC
VDC
VAC
VDC
O/3
VAC
VDC
O/4
0/5
L1
L2
O/2
L1/+dc
O/3
L2/-dc
VAC
VDC
L2/-dc
L1/+dc
O/2
L2/-dc
L1/+dc
VAC
VDC
L2/-dc
L1/+dc
O/1
L2/-dc
L1/+dc
L2
VAC
VDC
L2/-dc
L1/+dc
O/0
L2/-dc
L1/+dc
VAC
VDC
L2/N
L1
I/1
120/240V ac
L1/+dc
L1
DC
I/0
COM
L2/-dc
L1/+dc
120/240V ac
+24V -24V
dc
dc
OUT OUT
L1/+dc
+24V -24V
dc
dc
OUT OUT
+
24V dc In, Relay Out
Showing sourcing (sink load) configuration of inputs.
+
200mA max
24V dc In, Relay Out
Showing sinking (source load) configuration of inputs.
L2/-dc
1761-L16BWB
+
+
24V dc In, Relay Out
Showing sourcing (sink load) configuration of inputs.
+
24V dc In, Relay Out
Showing sinking (source load) configuration of inputs.
+
O/0
VAC
VDC
O/1
VAC
VDC
VAC
VDC
O/3
VAC
VDC
O/4
O/5
L2/-dc
L1/+dc
+
O/2
Not Not DC
I/0
Used Used COM
+24V -24V
dc
dc
IN
IN
VAC
VDC
I/1
I/2
I/3
DC
I/4
COM
I/5
I/6
I/7
I/8
I/9
O/0
VAC
VDC
O/1
VAC
VDC
VAC
VDC
O/3
VAC
VDC
O/4
O/5
L2/-dc
O/2
L2/-dc
L1/+dc
I/9
L2/-dc
L1/+dc
I/8
L2/-dc
L1/+dc
I/7
L2/-dc
L1/+dc
I/6
L1/+dc
I/5
+
DC
I/4
COM
L2/-dc
L1/+dc
I/3
L2/-dc
L1/+dc
VAC
VDC
I/2
L1/+dc
+24V -24V
dc
dc
IN
IN
I/1
L2/-dc
L1/+dc
Not Not DC
I/0
Used Used COM
L2/-dc
1761-L16NWA
DC
I/0
COM
I/1
I/2
I/3
DC
I/4
COM
200mA max
I/5
I/6
I/7
I/8
I/9
I/2
I/3
DC
I/4
COM
I/5
I/6
I/7
I/8
I/9
O/3
VAC
VDC
O/4
O/5
L2/-dc
L1
L1
L2/N
L2
VAC
VDC
O/0
VAC
VDC
0/1
VAC
VDC
VAC
VDC
O/3
VAC
VDC
O/4
0/5
O/2
L1/+dc
VAC
VDC
L2/-dc
O/2
L2/-dc
L1/+dc
VAC
VDC
L2/-dc
L1/+dc
O/1
L2/-dc
L1/+dc
VAC
VDC
L2/-dc
L1/+dc
O/0
L2/-dc
L1/+dc
L2
VAC
VDC
L2/-dc
L1/+dc
L1
L2/N
I/1
120/240V ac
L1/+dc
L1
DC
I/0
COM
L2/-dc
L1/+dc
120/240V ac
+24V -24V
dc
dc
OUT OUT
L1/+dc
+24V -24V
dc
dc
OUT OUT
+
24V ac or 24V dc In, Relay Out
Showing sourcing (sink load) configuration of inputs.
+
200mA max
24V ac or 24V dc In, Relay Out
Showing sinking (source load) configuration of inputs.
L2/-dc
Input circuits on this module are capable of 24V ac or 24V dc operation.
Publication CIG-WD001B-EN-P - May 2005
8-4
1761 Controller I/O on MicroLogix 1000 Controllers
1761-L16NWB
+
+
24V ac or 24V dc In, Relay Out
Showing sourcing (sink load) configuration of inputs.
+
24V ac or 24V dc In, Relay Out
Showing sinking (source load) configuration of inputs.
+
I/8
I/9
O/0
VAC
VDC
O/1
VAC
VDC
VAC
VDC
O/3
VAC
VDC
O/4
O/5
+24V -24V
dc
dc
IN
IN
VAC
VDC
+
L2/-dc
L1/+dc
O/2
Not Not DC
I/0
Used Used COM
I/1
I/2
I/3
DC
I/4
COM
I/5
I/6
I/7
I/8
I/9
O/0
VAC
VDC
O/1
VAC
VDC
VAC
VDC
O/3
VAC
VDC
O/4
O/5
L2/-dc
O/2
Input circuits on this module are capable of 24V ac or 24V dc operation.
1761-L20AWA-5A
79±132V ac
NOT
USED
NOT
USED
AC
COM
L1
I/0
I/1
Analog
Channels
79±132V ac
L2/N
I/2
L2/N
I/3
AC
COM
L1
I/4
I/5
I/6
I/7
I/8
I/9
I/10
I/11
IA
SHD
IA/0
V (+)
IA/1
V (+)
IA
(±)
IA
SHD
85±264 VAC
L1
L2/N
VAC
VDC
VAC
O/0 VDC
O/1
VAC
VDC
CR
VAC
O/2
O/3 VDC
CR
NOT
O/4
O/5
O/6
O/7 USED
CR
CR
CR
CR
OA
SHD
OA/0
V (+)
OA/0
I (+)
Analog
Channel
VAC 2
VDC 1
VAC 2
COM
VAC 1
VAC 1
COM
Publication CIG-WD001B-EN-P - May 2005
VDC 2
VDC 1
COM
VDC 2
COM
OA
(±)
IA/2
I (+)
IA/3
I (+)
IA
(±)
L2/-dc
L1/+dc
I/7
L2/-dc
L1/+dc
I/6
L2/-dc
L1/+dc
I/5
L2/-dc
L1/+dc
DC
I/4
COM
L1/+dc
I/3
L2/-dc
L1/+dc
I/2
L2/-dc
L1/+dc
VAC
VDC
L1/+dc
+
+24V -24V
dc
dc
IN
IN
I/1
L2/-dc
L1/+dc
Not Not DC
I/0
Used Used COM
L2/-dc
1761 Controller I/O on MicroLogix 1000 Controllers
8-5
1761-L20BWA-5A
Sinking Input Configuration
Analog
Channe ls
14–30V dc
VDC (–)
VDC (+)
VDC (+)
VDC (–)
+ 24V –
DC
CO M
DC OU T
I/0
I/1
I/2
DC
CO M
I/3
I/4
I/5
I/6
I/7
I/8
I/9
I/10
I/11
IA
SHD
IA/1
V (+)
IA/0
V (+)
IA
(–)
IA
SHD
IA/2
I (+)
IA/3
I (+)
IA
(–)
IA
SHD
IA/2
I (+)
IA/3
I (+)
IA
(–)
85–264 VAC
L1
VAC
VDC
L2/N
VAC
O/0 VDC
VAC
VDC
O/1
VAC
O/2
CR
NO T
OA
O /3 VDC
O/4
O/5
O /6
O/7 US ED SHD
CR
CR
CR
CR
CR
OA /0
V (+)
OA /0
I (+)
OA
(–)
Analog
Channe l
VAC 2
VDC 1
VDC 2
VDC 1
CO M
VAC 2
CO M
VAC 1
VDC 2
CO M
VAC 1
CO M
Sourcing Input Configuration
Analog
Channels
14–30V dc
VDC (+)
VDC (–)
VDC (–)
VDC (+)
+ 24V –
DC
CO M
DC OU T
I/0
I/1
I/2
I/3
DC
CO M
I/4
I/5
I/6
I/7
I/8
I/9
I/10
I/11
IA
SHD
IA/1
V (+)
IA/0
V (+)
IA
(–)
85–264 VAC
L1
L2/N
VAC
VDC
VAC
O/0 VDC
O/1
VAC
VDC
CR
VAC
O/2
NO T
OA
O /3 VDC
O/4
O/5
O /6
O/7 US ED SHD
CR
CR
CR
CR
CR
OA /0
V (+)
OA /0
I (+)
OA
(–)
Analog
Channe l
VAC 2
VDC 1
VAC 2
CO M
VAC 1
VDC 2
VDC 1
CO M
VDC 2
CO M
VAC 1
CO M
Publication CIG-WD001B-EN-P - May 2005
8-6
1761 Controller I/O on MicroLogix 1000 Controllers
1761-L20BWB-5A
Sinking Input Configuration
14–30V dc
NO T
US ED
NO T
DC
US ED CO M
VDC +
I/0
DC IN
+ 24V –
VAC
VDC
I/1
Analog
Channe ls
14–30V dc
VDC (–)
I/2
I/3
VAC
O/0 VDC
O/1
VDC (–)
DC
CO M
VDC (+)
I/4
VAC
VDC
I/5
I/6
I/7
I/8
I/9
I/11
I/10
VAC
O/2
CR
NO T
IA
SHD
OA
O /3 VDC
O/4
O/5
O /6
O/7 US ED SHD
CR
CR
CR
CR
CR
IA/0
V (+)
IA/1
V (+)
OA /0
V (+)
OA /0
I (+)
IA
(–)
IA
SHD
IA/2
I (+)
IA/3
I (+)
IA
(–)
IA
SHD
IA/2
I (+)
IA/3
I (+)
IA
(–)
OA
(–)
Analog
Channe l
VAC 1
VDC 2
VDC 3
VAC 1
CO M
VDC 1
VDC 2
CO M
VDC 3
CO M
VDC 1
CO M
Sourcing Input Configuration
14–30V dc
VDC (+)
NO T
US ED
NO T
DC
US ED CO M
DC IN
+ 24V –
I/0
VAC
VDC
I/1
Analog
Channe ls
14–30V dc
VDC (–)
I/2
I/3
VAC
O/0 VDC
O/1
VDC (+)
DC
CO M
VDC (–)
I/4
VAC
VDC
CR
I/5
I/6
I/7
I/9
I/8
I/10
VAC
O/2
I/11
NO T
IA
SHD
OA
O /3 VDC
O/4
O/5
O /6
O/7 US ED SHD
CR
CR
CR
CR
CR
IA/0
V (+)
IA/1
V (+)
OA /0
V (+)
OA /0
I (+)
Analog
Channe l
VAC 1
VDC 2
VAC 1
CO M
VDC 1
VDC 1
CO M
Publication CIG-WD001B-EN-P - May 2005
VDC 3
VDC 2
CO M
VDC 3
CO M
IA
(–)
OA
(–)
1761 Controller I/O on MicroLogix 1000 Controllers
8-7
1761-L32AAA
120V ac In, 120/240V ac and Relay Out
L2
L1
I/0
Not Not AC
Used Used COM
L2
L1
I/15
I/1
I/2
I/3
AC
I/4
COM
I/5
I/6
I/7
I/8
I/9
I/10
I/11
I/12
I/13
I/14
O/0
VAC
VDC
O/1
VAC
O/3
VAC
O/4
O/5
O/6
O/7
VAC
O/8
O/9
O/10 O/11
I/16
I/17
I/18
I/19
I/16
I/17
I/18
I/19
L2
L2/-dc
L1
VAC
VDC
L2/N
L1/+dc
L1
L2/-dc
L1/+dc
120/240V ac
O/2
L1
L2
L1
L2
L1
L2
1761-L32AWA
120V ac In, Relay Out
L2
L1
I/0
Not Not AC
Used Used COM
L2
L1
I/15
I/1
I/2
I/3
AC
I/4
COM
I/5
I/6
I/7
I/8
I/9
I/10
I/11
I/12
I/13
I/14
O/0
VAC
VDC
O/1
VAC
VDC
O/3
VAC
VDC
O/4
O/5
O/6
O/7
VAC
VDC
O/8
O/9
O/10 O/11
L2/-dc
L2/-dc
L1/+dc
O/2
L1/+dc
L2
VAC
VDC
L2/-dc
L1/+dc
L1
L2/N
L1/+dc
L1
L2/-dc
L1/+dc
120/240V ac
L2/-dc
Publication CIG-WD001B-EN-P - May 2005
8-8
1761 Controller I/O on MicroLogix 1000 Controllers
1761-L32BBB
24V dc In, 24V dc and Relay Out
Showing sinking (source load) configuration of inputs.
+
+
DC
I/4
COM
I/5
I/6
I/7
I/8
I/9
I/10
I/11
I/12
I/13
I/14
O/0
VAC
VDC
O/1
+24V
dc
O/2
O/3
O/4
O/5
O/6
O/7
O/8
O/9
O/10 O/11
-24V
dc
+
I/15
I/16
I/17
I/18
I/19
I/16
I/17
I/18
I/19
Not
Used
+
I/3
L1/+dc
VAC
VDC
I/2
L2/-dc
+24V -24V
dc
dc
IN
IN
I/1
L2/-dc
L1/+dc
Not Not DC
I/0
Used Used COM
+
24V dc In, 24V dc and Relay Out
Showing sourcing (sink load) configuration of inputs.
+
DC
I/4
COM
I/5
I/6
I/7
I/8
I/9
I/10
I/11
I/12
I/13
I/14
O/0
VAC
VDC
O/1
+24V
dc
O/2
O/3
O/4
O/5
O/6
O/7
O/8
O/9
O/10 O/11
-24V
dc
Publication CIG-WD001B-EN-P - May 2005
+
I/3
L2/-dc
VAC
VDC
I/2
L1/+dc
+
+24V -24V
dc
dc
IN
IN
I/1
L2/-dc
L1/+dc
Not Not DC
I/0
Used Used COM
I/15
Not
Used
1761 Controller I/O on MicroLogix 1000 Controllers
8-9
1761-L32BWA
Sinking Input Configuration
14- 30 V dc
VDC (–)
VDC +
VDC +
VDC (–)
+ 24V –
DC
CO M
DC OU T
I/0
I/1
I/2
I/3
DC
CO M
I/4
I/5
I/6
I/7
I/8
I/9
I/10
I/11
I/12
I/13
I/14
I/15
I/16
I/17
I/18
I/19
85–264 VAC
L1
VAC
VDC
L2/N
VAC
O/0 VDC
O/1
VAC
VDC
VAC
O/2
CR
VAC 2
O/4
O/5
O /6
O/7 VDC
CR
CR
CR
CR
CR
VDC 1
VDC 2
O/8
O /9
CR
CR
O/10 O/11
CR
CR
VDC 3
VDC 1
CO M
VAC 2
CO M
VAC 1
VAC
O /3 VDC
VDC 2
CO M
VDC 3
CO M
VAC 1
CO M
Sourcing Input Configuration
14- 30 V dc
VDC (–)
VDC (+)
VDC (–)
VDC (+)
+ 24V –
DC
CO M
DC OU T
I/0
I/1
I/2
I/3
DC
CO M
I/4
I/5
I/6
I/7
I/8
I/9
I/10
I/11
I/12
I/13
I/14
I/15
I/16
I/17
I/18
I/19
85–264 VAC
L1
L2/N
VAC
VDC
VAC
O/0 VDC
O/1
VAC
VDC
CR
VAC 2
VAC
O /3 VDC
O/4
O/5
O /6
O/7 VDC
CR
CR
CR
CR
CR
VDC 1
VAC 2
CO M
VAC 1
VAC
O/2
VDC 2
VDC 1
CO M
O/8
O /9
CR
CR
O/10 O/11
CR
CR
VDC 3
VDC 2
CO M
VDC 3
CO M
VAC 1
CO M
Publication CIG-WD001B-EN-P - May 2005
8-10
1761 Controller I/O on MicroLogix 1000 Controllers
1761-L32BWB
Sinking Input Configuration
14–30V dc
VDC (–)
NO T
US ED
NO T
DC
US ED CO M
I/0
I/1
VAC
VDC
O/0 VDC
DC IN
+ 24V –
14–30V dc
VDC (+)
I/2
VDC (–)
VDC (+)
I/3
DC
CO M
I/4
I/5
O/1
VAC
VDC
O/2
VAC
VAC 1
I/7
I/8
I/9
I/10
O /3 VDC
O/4
O/5
O /6
O/7 VDC
CR
CR
CR
CR
CR
VAC
CR
VDC 2
I/11
I/12
I/13
I/14
I/15
O/8
O /9
O/10 O/11
CR
CR
I/16
I/17
I/18
I/19
VAC
VDC 3
CR
CR
VDC 4
VDC 2
CO M
VAC 1
CO M
VDC 1
I/6
VDC 3
CO M
VDC 4
CO M
VDC 1
CO M
Sourcing Input Configuration
14–30V dc
VDC (+)
NO T
US ED
NO T
DC
US ED CO M
DC IN
+ 24V –
14–30V dc
VDC (–)
I/0
I/1
I/2
VAC
VDC
O/0 VDC
VDC (+)
I/3
DC
CO M
I/4
I/5
O/1
VAC
VDC
O/2
VAC
CR
VAC 1
VDC 1
CO M
Publication CIG-WD001B-EN-P - May 2005
I/7
I/8
I/9
I/10
O /3 VDC
I/6
O/4
O/5
O /6
O/7 VDC
CR
CR
CR
CR
CR
VAC
VDC 2
VAC 1
CO M
VDC 1
VDC (–)
I/12
I/13
I/14
I/15
O/8
O /9
O/10 O/11
CR
CR
VAC
VDC 3
VDC 2
CO M
I/11
CR
CR
VDC 4
VDC 3
CO M
VDC 4
CO M
I/16
I/17
I/18
I/19
Chapter
9
1762 I/O on MicroLogix 1200 Controllers
Unlike the other product sections in this document, this section does
not list the 1762 catalog numbers in alphabetical order; instead, we
first list the embedded controller I/O catalog numbers first because of
their regular use in most 1762 applications.
As you use this section, keep the following in mind:
IMPORTANT
• Catalog numbers that begin with 1762-Lxx (e.g.
1762-L24AWA) represent embedded I/O products
• Catalog numbers that begin in any combination
other than 1762-Lxx (e.g. 1762-IA8) represent
expansion I/O products
1762-L24AWA
1762-L24AWAR
Input Wiring
L1a
Terminal Groupings
L1b
L2b
NC
NC
IN 0
COM
0
COM
1
IN 2
IN 1
Inpu t Gro u p
Group 0
Group 1
IN 3
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
C o m m o n T e rm in al
AC COM 0
AC COM 1
Inpu t Te rm in a ls
I/0 through I /3
I/4 through I /13
IN 13
IN 12
NC - No connection
L2a
L1a
L1b
Output Wiring
Terminal Groupings
-DCa
L2a
L2b
L1c
L2c
Ou tput Group
Group 0
Group 1
Group 2
Group 3
Group 4
L2d
L2
CR
CR
L1
VAC
L1
VAC OUT 0 OUT 1 OUT 2
NEUT
VAC
DC 0
VAC
DC 1
VAC
DC 2
VAC OUT 5 OUT 6 OUT 8
DC 3
OUT 3 OUT 4
VAC
DC 4
CR
Voltage Te rm in a l
VAC/VD C 0
VAC/ VDC 1
VAC/VD C 2
VAC/ VDC 3
VAC/VD C 4
Ou tput Te rm in al
O/ 0
O/1
O/2 through O/3
O4 through O /5
O/6 through O/9
OUT 7 OUT 9
CR
L2d
+DCa
1
L1a
L1b
L2b
L2c
L1d
Publication CIG-WD001B-EN-P - May 2005
9-2
1762 I/O on MicroLogix 1200 Controllers
1762-L24BWA
1762-L24BWAR
Sinking Input Wiring
-DCb
+DCa
+DC
+DCb
Terminal Groupings
+24
VDC
IN 0
24
COM COM 0
IN 2 COM 1
IN 1
IN 3
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
IN 13
Inpu t Grou p
C o m m o n T e rm i n al
Inpu t Te rm in a l
Group 0
Group 1
DC COM 0
DC COM 1
I/0 through I /3
I/4 through I /13
IN 12
The 24V dc sensor power source must not be used
to power output circuits. It should only be used
to power input devices (e.g. sensors, switches).
+DCb
-DC
-DCa
+DCa
Sourcing Input Wiring
+DCb
-DCa
24V dc Sensor Power
-DCb
Terminal Groupings
+DC
+24
VDC
IN 0
24
COM COM 0
IN 1
IN 2 COM 1
IN 3
IN 5
IN 4
IN 7
IN 6
IN 9 IN 11
IN 8
IN 10
IN 13
Inpu t Grou p
C o m m o n T e rm in al
Inpu t Te rm in a l
Group 0
Group 1
DC COM 0
DC COM 1
I/0 through I /3
I/4 through I /13
IN 12
The 24V dc sensor power source must not be used
to power output circuits. It should only be used
to power input devices (e.g. sensors, switches).
-DCb
-DC +DCa
-DCa
Output Wiring
-DCa
L2a
L2b
L1c
L2c
Terminal Groupings
L2d
L2
CR
CR
L1
VAC
L1
VAC OUT 0 OUT 1 OUT 2
NEUT
VAC
DC 0
VAC
DC 1
VAC
DC 2
VAC OUT 5 OUT 6 OUT 8
DC 3
OUT 3 OUT 4
VAC
DC 4
CR
OUT 7 OUT 9
CR
L2d
+DCa
L1a
L1b
Publication CIG-WD001B-EN-P - May 2005
L2b
L2c
L1d
Ou tput Group
Group 0
Group 1
Group 2
Group 3
Group 4
Voltage Termin a l
VAC/VD C 0
VAC/ VDC 1
VAC/VD C 2
VAC/ VDC 3
VAC/VD C 4
Output Te rm in al
O/0
O/1
O/2 through O/3
O4 through O /5
O/6 through O/9
1762 I/O on MicroLogix 1200 Controllers
9-3
1762-L24BXB
1762-L24BXBR
Sinking Input Wiring
NC
+DCb
IN 0
NC
Terminal Groupings
-DCb
+DCa
IN 2 COM 1
COM 0
IN 1
-DCa
+DCa
IN 3
IN 5
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
IN 13
IN 12
Input Grou p
C o m m o n T e rm in al
Inpu t Te rm in a l
Group 0
Group 1
Group 0
DC COM 0
DC COM 1
AC COM 0
I/0 through I /3
I/4 through I /13
I/0 through I /3
NC - No connection
+DCb
Sourcing Input Wiring
-DCa
0
NC
NC
+DCb
IN 2
COM0
IN 1
+DCa
-DCa
IN 5
COM1
IN 3
Terminal Groupings
-DCb
IN 4
IN 7
IN 6
IN 9
IN 8
IN 11
IN 10
IN 13
IN 12
Input Grou p
C o m m o n T e rm in al
Inpu t Te rm in a l
Group 0
Group 1
Group 0
DC COM 0
DC COM 1
AC COM 0
I/0 through I /3
I/4 through I /13
I/0 through I /3
NC - No connection
-DCb
Output Wiring
-DCa
+DC
+24
VDC
-DCb
L1d
-DCc
Terminal Groupings
L2d
-DC
VDC
NEUT
OUT
0
VAC
DC 0
OUT
1
VAC
DC 1
CR
CR
OUT
2
OUT
4
VDC
2
OUT
3
CR
+DCa +DCb
+DCc
-DCc
OUT
6
OUT
5
VAC
DC 3
COM
2
OUT
8
OUT
7
OUT
9
Ou tput Grou p
Voltage Te rmin a l
Ou tput Te rm i n al
Group 0
Group 1
Group 2
Group 3
VAC/VD C 0
VAC/ VDC 1
VD C 2, VD C C OM 2
VAC/ VDC 3
O/ 0
O/1
O/2 thr ough O/6
O/7 thr ough O/9
CR
L2d
Publication CIG-WD001B-EN-P - May 2005
9-4
1762 I/O on MicroLogix 1200 Controllers
1762-L40AWA
1762-L40AWAR
Input Wiring
L1a
L1b
Terminal Groupings
L1c
Input Group
Group 0
Group 1
Group 2
L2b
COM
IN 5 IN 7 IN 8 IN 10 IN 12 IN 14 IN 16 IN 18 IN 20 IN 22
NC IN 0 IN 2 1
NC
COM
IN 1
0
IN 3
IN 4
IN 6
COM
2
Common Terminal
AC COM 0
AC COM 1
AC COM 2
Input Terminal
I/0 through I/3
I/4 through I/7
I/8 through I/23
IN 9 IN 11 IN 13 IN 15 IN 17 IN 19 IN 21 IN 23
NC - No connection
L2a
L2c
L1a
L1b
L1c
Output Wiring
Terminal Groupings
L1d
L2a
L2b
L1f
L2d
L2c
Output Group
L2f
L2e
L2
CR
L1
VAC
L1
VAC
NEUT
OUT
0
VAC
DC 0
OUT
1
VAC
DC 1
OUT
2
VAC
DC 2
CR
VAC
DC 3
OUT
3
OUT
5
OUT
4
L2c
L1b
L1c
Publication CIG-WD001B-EN-P - May 2005
OUT
6
OUT
8
VAC
DC 4
OUT
10
OUT
9
L2d
CR
VAC
DC 5
OUT
11
L2e
L1e
OUT
15
OUT
13
OUT
12
OUT
14
CR
CR
CR
CR
L1a
OUT
7
CR
L2f
Group 0
Group 1
Group 2
Group 3
Group 4
Group 5
Voltage Terminal
VAC/VD C 0
VAC/ VDC 1
VAC/VD C 2
VAC/ VDC 3
VAC/VD C 4
VAC/ VDC 5
Output Terminal
O/0
O/1
O/2 thr ough O/3
O/4 thr ough O/7
O/8 thr ough O/11
O/12 thr ough O/15
1762 I/O on MicroLogix 1200 Controllers
9-5
1762-L40BWA
1762-L40BWAR
Sinking Input Wiring
+DC
+DCa
+24
VDC
IN 0
Terminal Groupings
+DCb
-DCb
Input Group
Group 0
Group 1
Group 2
+DCc
24
COM
COM
0
-DC
-DCa
COM
1
IN 2
IN 1
IN 5
IN 3
IN 4
IN 7
IN 8
COM
2
IN 6
IN 10
IN 9
IN 12
IN 11
IN 14
IN 13
IN 16
IN 15
IN 18
IN 17
IN 20
IN 19
Common Terminal
DC COM 0
DC COM 1
DC COM 2
Input Terminal
I/0 through I/3
I/4 through I/7
I/8 through I/23
IN 22
IN 21
IN 23
The 24V dc sensor power source must not be used
to power output circuits. It should only be used
to power input devices (e.g. sensors, switches).
+DCc
-DCc
+DCb
+DCa
Sourcing Input Wiring
Terminal Groupings
-DCb
+DCb
-DCa
Input Group
Group 0
Group 1
Group 2
-DCc
+DC
+24
VDC
24
COM
IN 0
COM
0
-DC
IN 2
IN 1
COM
1
IN 3
IN 5
IN 4
-DCa
IN 7
IN 6
IN 8
COM
2
IN 10
IN 9
IN 12
IN 11
IN 14
IN 13
IN 16
IN 15
IN 18
IN 17
IN 20
IN 19
Common Terminal
DC COM 0
DC COM 1
DC COM 2
Input Terminal
I/0 through I/3
I/4 through I/7
I/8 through I/23
IN 22
IN 21
IN 23
The 24V dc sensor power source must not be used
to power output circuits. It should only be used
to power input devices (e.g. sensors, switches).
-DCb
-DCc
+DCa
+DCc
Output Wiring
Terminal Groupings
L1d
L2a
L2b
L1f
L2d
L2c
Output Group
L2f
L2e
L2
CR
L1
VAC
L1
VAC
NEUT
OUT
0
VAC
DC 0
OUT
1
VAC
DC 1
OUT
2
VAC
DC 2
CR
VAC
DC 3
OUT
3
OUT
5
OUT
4
L2c
L1b
L1c
OUT
6
OUT
8
VAC
DC 4
OUT
10
OUT
9
L2d
CR
VAC
DC 5
OUT
11
L2e
OUT
15
OUT
13
OUT
12
Voltage Terminal
VAC/VD C 0
VAC/ VDC 1
VAC/VD C 2
VAC/ VDC 3
VAC/VD C 4
VAC/ VDC 5
Output Terminal
O/ 0
O/1
O/2 through O/3
O/4 through O/7
O/8 through O/11
O/12 through O/15
OUT
14
CR
CR
CR
CR
L1a
OUT
7
CR
Group 0
Group 1
Group 2
Group 3
Group 4
Group 5
L2f
L1e
Publication CIG-WD001B-EN-P - May 2005
9-6
1762 I/O on MicroLogix 1200 Controllers
1762-L40BXB
1762-L40BXBR
Sinking Input Wiring
Terminal Groupings
-DCb +DCb
+DCa
+DCc
IN 0
NC
COM
0
NC
IN 2
IN 1
COM
1
IN 3
IN 5
IN 4
IN 7
IN 8
IN 12
IN 14
IN 16
IN 18
IN 20
Common Terminal
DC COM 0
DC COM 1
DC COM 2
Input Terminal
I/0 through I/3
I/4 through I/7
I/8 through I/23
IN 22
NC - No connection
COM
2
IN 6
IN 10
Input Group
Group 0
Group 1
Group 2
IN 9 IN 11
IN 13
IN 15
IN 17
IN 19
IN 21
IN 23
+DCc
+DCa
-DCa
+DCb -DCc
Sourcing Input Wiring
Terminal Groupings
+DCb
-DCb
-DCa
-DCc
NC
NC
IN 0
COM
0
+DCa
IN 2
IN 1
COM
1
IN 5
IN 3
IN 4
IN 7
IN 6
IN 8
IN 10
IN 12
IN 14
IN 16
IN 18
IN 20
Input Group
Group 0
Group 1
Group 2
Common Terminal
DC COM 0
DC COM 1
DC COM 2
Input Terminal
I/0 through I/3
I/4 through I/7
I/8 through I/23
IN 22
NC - No connection
COM
2
IN 9
IN 11
IN 13
IN 15
IN 17
IN 19
IN 21
IN 23
-DCc
-DCa
-DCb
+DCc
Output Wiring
-DCa
-DC
-DCc
-DCb
CR
+DC
+24
VDC
VDC
NEUT
OUT
0
VAC
DC 0
OUT
1
VAC
DC 1
VDC
2
OUT
4
OUT
3
OUT
8
OUT
6
OUT
5
CR
+DCe
COM
OUT
7
OUT
9
CR
CR
OUT
10
VAC
DC3
CR
VAC
DC 4
OUT
11
CR
-DCd
+DCa +DCb
+DCc
Publication CIG-WD001B-EN-P - May 2005
+DCd
Terminal Groupings
-DCe
CR
CR
OUT
2
-DCd
OUT
15
OUT
13
OUT
12
OUT
14
CR
-DCe
Ou tp ut G rou p
Group 0
Group 1
Group 2
Group 3
Group 4
Vo lta ge Te rm in a l
VAC/VD C 0
VAC/VDC 1
VD C 2 , VD C C OM 2
VAC/VDC 3
VAC/VD C 4
O u tp ut Te rm in al
O/0
O/1
O/2 through O/9
O/10 through O/11
O/12 through O/15
1762 I/O on MicroLogix 1200 Controllers
9-7
1762-IA8
L1
Be careful when stripping wires. Wire fragments that fall into a
module could cause damage when power is applied. Once wiring
is complete, ensure the module is free of all metal fragments.
IN 0
IN 1
IN 2
IN 3
100/120V ac
IN 4
A current limiting resistor can be used to limit inrush current; however, the operating
characteristics of the ac input circuit will be affected. If a 6.8KΩ resistor is placed in
series with the input, the inrush current is reduced to 35 mA. In this configuration the
minimum on-state voltage increases to 92V ac. Before adding the resistor in a hazardous
environment, be sure to consider the operating temperature of the resistor and the
temperature limits of the environment. The operating temperature of the resistor must
remain below the temperature limit of the environment.
IN 5
IN 6
IN 7
AC
COM
AC
COM
L2
Commons are
connected
internally.
Also, this product is intended to be mounted to a well-grounded mounting surface
such as a metal panel. Additional grounding connections from the module’s mounting tabs
or DIN rail (if used) are not required unless the mounting surface cannot be grounded.
1762-IF2OF2
Differential Sensor Transmitter Types
IN 0 +
Analog Sensor
IN 0 IN 1 +
IN 1 V out 0
I out 0
Analog Load
V out 1
I out 1
COM
COM
2-Wire Transmitter
Power +
Supply (1)
Commons connected
internally.
Transmitter
+
-
Module
IN +
-
IN COM
3-Wire Transmitter
Power +
Supply(1)
Analog outputs may fluctuate for less than
a second when power is applied or removed.
This characteristic is common to most
analog outputs. While the majority of loads
will not recognize this short signal, it is
recommended that preventive measures be
taken to ensure that connected equipment
is not affected.
Transmitter
Supply
Signal
All power supplies rated N.E.C. Class 2.
Module
IN +
-
Grounding the cable shield at the module end only usually
provides sufficient noise immunity. However, for best cable
shield performance, earth ground the shield at both ends,
using a 0.01µF capacitor at one end to block AC power ground
currents, if necessary.
IN -
Select the input type, current or voltage, using the switch
located on the module’s circuit board and the input type/range
selection bits in the Configuration Data File.
COM
The output type selection, current or voltage, is made by
wiring to the appropriate terminals, Iout or Vout, and by the
type/range selection bits in the Configuration Data File.
4-Wire Transmitter
Power +
Supply(1)
-
Transmitter
Supply
+
-
Signal
Module
+
-
IN +
IN COM
Publication CIG-WD001B-EN-P - May 2005
9-8
1762 I/O on MicroLogix 1200 Controllers
1762-IF4
Differential Sensor Transmitter Types
IN0 +
Analog Sensor
IN0 IN1 +
IN1 IN2 +
IN2 IN3 +
IN3 -
COM
COM
2-Wire Transmitter
Commons connected
internally.
Grounding the cable shield at the module end only
usually provides sufficient noise immunity. However,
for best cable shield performance, earth ground the
shield at both ends, using a 0.01µF capacitor at one
end to block AC power ground currents, if necessary.
Transmitter
+
Power +
Supply (1)
Module
-
IN +
-
IN COM
All power supplies rated N.E.C. Class 2.
Select the input type, current or voltage, using the
switch located on the module’s circuit board and
the input type/range selection bits in the Configuration
Data File.
Transmitter
3-Wire Transmitter
Supply
Power +
Supply(1)
Module
Signal
IN +
-
IN COM
Transmitter
4-Wire Transmitter
Supply
Power +
Supply(1)
+
-
-
Signal
Module
+
-
IN +
IN COM
1762-IQ16
+DC (sinking)
-DC (sourcing)
IN 0
IN 1
IN 2
IN 3
IN 4
24V dc
Be careful when stripping wires. Wire fragments that fall into a
module could cause damage when power is applied. Once wiring
is complete, ensure the module is free of all metal fragments.
IN 5
IN 6
IN 7
-DC (sinking)
DC
COM 0
+DC (sinking)
+DC (sourcing)
-DC (sourcing)
IN 8
IN 9
IN 10
24V dc
IN 11
IN 12
IN 13
-DC (sinking)
IN 14
IN 15
+DC (sourcing)
Publication CIG-WD001B-EN-P - May 2005
Miswiring of the module to an AC power source will damage
the module.
DC
COM 1
Sinking/Sourcing Inputs - Sourcing/sinking describes the current flow between the
I/O module and the field device. Sourcing I/O circuits supply (source) current to sinking
field devices. Sinking I/O circuits are driven by a current sourcing field device.
Field devices connected to the negative side (DC Common) of the field power supply
are sinking field devices. Field devices connected to the positive side (+V) of the
field supply are sourcing field devices.
Also, this product is intended to be mounted to a well-grounded mounting surface
such as a metal panel.
1762 I/O on MicroLogix 1200 Controllers
9-9
1762-IQ8
+D C (sinking)
-DC (sourcing)
Be careful when stripping wires. Wire fragments that fall into a
module could cause damage when power is applied. Once wiring is
complete, ensure the module is free of all metal fragments.
IN 0
IN 1
IN 2
IN 3
24V dc
Miswiring of the module to an AC power source will damage
the module.
IN 4
IN 5
IN 6
IN 7
DC
COM
DC
COM
-DC (sinking)
+D C (sourcing)
Commons are
connected internally.
Sinking/Sourcing Inputs - Sourcing/sinking describes the current flow between the
I/O module and the field device. Sourcing I/O circuits supply (source) current to sinking
field devices. Sinking I/O circuits are driven by a current sourcing field device.
Field devices connected to the negative side (DC Common) of the field power supply
are sinking field devices. Field devices connected to the positive side (+V) of the
field supply are sourcing field devices.
Also, this product is intended to be mounted to a well-grounded mounting surface
such as a metal panel.
1762-IR4 2-Wire Potentiometer Interconnection
Cable Shield (to Ground)
EXC 2
Potentiometer
Cable Shield (to Ground)
RTD EXC
SENSE 2
Return
Potentiometer
Sense
Return
RTN 2
Belden 9501 Shielded Cable
NC
Belden 83503 or 9533 Shielded Cable
NC
Cable Shield (to Ground)
Cable Shield (to Ground)
Potentiometer
RTD EXC
EXC 2
EXC 2
SENSE 2
Return
SENSE 2
RTN 2
NC
Run RTD and sense wires from the module to
potentiometer terminal and tie terminal to one point.
RTD EXC
EXC 2
SENSE 2
RTN 2
1762-IR4 3-Wire Potentiometer Interconnection
Belden 9501 Shielded Cable
RTN 2
NC
TIP: The potentiometer wiper arm can be connected to either the EXC or return terminal
depending on whether you want increasing or decreasing resistance.
TIP:
Run RTD and sense wires from the module to
potentiometer terminal and tie terminal to one point.
RTD EXC
Potentiometer
Sense
Return
Belden 83503 or 9533 Shielded Cable
The potentiometer wiper arm can be connected to either the EXC or return terminal
depending on whether you want increasing or decreasing resistance.
IMPORTANT: Using 2-wire configurations does not permit the module to compensate for
resistance error due to lead wire length. The resulting analog data includes
the effect of this uncompensated lead wire resistance. The module continues
to place the uncompensated analog data in the input data file, but the
open-circuit status bit (OCx) is set in word 4 of the input data file for any
enabled channel using a 2-wire configuration. These status bits may be used
in the control program to indicate that the analog data includes error due to
uncompensated lead wires.
Publication CIG-WD001B-EN-P - May 2005
9-10
1762 I/O on MicroLogix 1200 Controllers
1762-IR4 2-Wire RTD
1762-IR4 3-Wire RTD
Cable Shield (to Ground)
Cable Shield (to Ground)
RTD EXC
RTD EXC
RTD EXC
Return
Return
SENSE 2
SENSE 2
RTN 2
RTN 2
Belden 9501 Shielded Cable
NC
IMPORTANT:
RTD EXC
EXC 2
EXC 2
Sense
Sense
Return
Return
NC
Belden 83503 or 9533 Shielded Cable
1762-IR4 4-Wire RTD
Using 2-wire configurations does not permit the module to compensate
for resistance error due to lead wire length. The resulting analog
data includes the effect of this uncompensated lead wire resistance.
The module continues to place the uncompensated analog data in
the input data file, but the open-circuit status bit (OCx) is set in word 4
of the input data file for any enabled channel using a 2-wire
configuration. These status bits may be used in the control program
to indicate that the analog data includes error due to uncompensated
lead wires.
Cable Shield (to Ground)
RTD EXC
RTD EXC
EXC 2
Sense
Sense
Return
Return
SENSE 2
RTN 2
NC
Belden 83503 or 9533 Shielded Cable
Leave one sensor wire open.
1762-IT4
CJC sensor
CJC+
CJC IN 2+
-
+
grounded thermocouple
IN 0-
ungrounded thermocouple
+
IN 0+
IN 2-
IN 1 +
within 10V dc
IN 1-
+
IN 3+
IN 3-
-
grounded thermocouple
COLD JUNCTION COMPENSATION
To obtain accurate readings from each of the channels, the temperature between the thermocouple wire and the input
channel must be compensated for. A cold junction compensating thermistor has been integrated in the terminal block.
The thermistor must remain installed to retain accuracy.
Do not remove or loosen the cold junction compensating thermistor assembly. This assembly is critical
to ensure accurate thermocouple input readings at each channel. The module will operate in the
thermocouple mode, but at reduced accuracy if the CJC sensor is removed.
IMPORTANT: When using grounded and/or exposed thermocouples that are touching electrically conductive material, the
ground potential between any two channels cannot exceed ±10V dc, or temperature readings will be inaccurate.
TIP:
When using an ungrounded thermocouple, the shield must be connected at the module end.
Publication CIG-WD001B-EN-P - May 2005
1762 I/O on MicroLogix 1200 Controllers
9-11
1762-OA8
VAC
0
OUT 0
CR
L2
100 to 240V ac
OUT 1
CR
OUT 3
CR
OUT 4
CR
L2
OUT 2
VAC
1
L1
100 to 240V ac
L1
CR
OUT 5
CR
OUT 6
Be careful when stripping wires. Wire fragments that fall into a
module could cause damage when power is applied. Once wiring is
complete, ensure the module is free of all metal fragments.
Miswiring of the module to an AC power source will damage
the module.
To limit the effects of leakage current through triac outputs, a loading resistor can be connected
in parallel with your load. For typical 120V ac applications, use a 15k ohm, 2W resistor. For
typical 240V ac applications, use a 15k ohm, 5W resistor.
OUT 7
1762-OB16
+DC
VDC+
CR
CR
OUT 0
OUT 1
CR
OUT 3
CR
OUT 2
OUT 4
Be careful when stripping wires. Wire fragments that fall into a
module could cause damage when power is applied. Once wiring
is complete, ensure the module is free of all metal fragments.
OUT 5
CR
OUT 6
CR
OUT 7
CR
OUT 8
CR
OUT 9
CR
OUT 11
Miswiring of the module to an AC power source will damage
the module.
24V dc (source)
OUT 10
Surge Suppression – Connecting surge suppressors across your external inductive load
will extend the life of the relay contacts. For additional details, refer to Industrial
Automation Wiring and Grounding Guidelines, Allen-Bradley publication 1770-4.1.
OUT 12
CR
OUT 13
OUT 14
OUT 15
DC COM
-DC
1762-OB8
+DC
+VDC
CR
OUT 0
CR
OUT 2
OUT 1
CR
OUT 3
CR
OUT 4
OUT 5
CR
OUT 6
CR
OUT 7
24V dc (source)
Be careful when stripping wires. Wire fragments that fall into a
module could cause damage when power is applied.
Once wiring is complete, ensure the module is free of all
metal fragments.
DC COM
-DC
Publication CIG-WD001B-EN-P - May 2005
9-12
1762 I/O on MicroLogix 1200 Controllers
1762-OF4
V out 0
Voltage Load
I out 0
Current Load
V out 1
I out 1
V out 2
I out 2
V out 3
I out 3
COM
COM
Analog outputs may fluctuate for less than a second when power is applied or
removed. This characteristic is common to most analog outputs. While the majority of
loads will not recognize this short signal, it is recommended that preventive measures
be taken to ensure that connected equipment is not affected.
TIP
Grounding the cable shield at the module end only usually provides sufficient noise
immunity. However, for best cable shield performance, earth ground the shield at both
ends, using a 0.01 µF capacitor at one end to block AC power ground currents,
if necessary.
1762-OX6I
L1-0
L1 OR +DC
OUT0 N.C.
L1 OR +DC
OUT0 N.O.
CR
OUT1 N.C.
CR
L1-1
OUT1 N.O.
L2 OR -DC
L1-2
L2 OR -DC
L2 OR -DC
CR
L1 OR +DC
OUT2 N.C.
OUT2 N.O.
L1 OR +DC
L2 OR -DC
CR
L1-3
Surge Suppression – Connecting surge
suppressors across your external inductive
load will extend the life of the relay contacts.
For additional details, refer to publication 1770-4.1.
OUT3 N.C.
OUT3 N.O.
L1 OR +DC
L1-4
OUT4 N.C.
CR
OUT4 N.O.
L2 OR -DC
L1-5
CR
L1 OR +DC
OUT5 N.C.
OUT5 N.O.
Publication CIG-WD001B-EN-P - May 2005
This product is intended to be mounted
to a well-grounded mounting surface such
as a metal panel. Additional grounding
connections from the module’s mounting
tabs or DIN rail (if used) are not required
unless the mounting surface cannot be
grounded. For more information, refer to
Industrial Automation Wiring and Grounding
Guidelines, Allen-Bradley publication 1770-4.1.
L2 OR -DC
1762 I/O on MicroLogix 1200 Controllers
9-13
1762-OW16
OUT 0
CR
L1 or +DC
VAC-VDC
0
OUT 1
CR
OUT 3
CR
OUT 5
CR
L2 or -DC
OUT 2
OUT 4
CR
OUT 6
CR
OUT 7
Be careful when stripping wires. Wire fragments that fall into a
module could cause damage when power is applied.
Once wiring is complete, ensure the module is free of all
metal fragments.
VAC-VDC
1
L1 or +DC
OUT 8
CR
OUT 9
CR
OUT 11
CR
OUT 13
CR
OUT 15
CR
L2 or -DC
Surge Suppression – Connecting surge suppressors across your external inductive
load will extend the life of the relay contacts. For additional details, refer to
Industrial Automation Wiring and Grounding Guidelines, Allen-Bradley publication 1770-4.1.
OUT 10
OUT 12
CR
OUT 14
1762-OW8
OUT 0
CR
L2 or - DC
L1 or +D C
OUT 1
CR
OUT 3
CR
L2 or -D C
OUT 2
VAC-VDC
1
L1 or +D C
VAC-VDC
0
CR
OUT 5
CR
OUT 6
OUT 7
OUT 4
CR
Be careful when stripping wires. Wire fragments that fall into a
module could cause damage when power is applied.
Once wiring is complete, ensure the module is free of all
metal fragments.
Surge Suppression – Connecting surge suppressors across your external inductive
load will extend the life of the relay contacts. For additional details, refer to
Industrial Automation Wiring and Grounding Guidelines, Allen-Bradley publication 1770-4.1.
Publication CIG-WD001B-EN-P - May 2005
9-14
1762 I/O on MicroLogix 1200 Controllers
Notes:
Publication CIG-WD001B-EN-P - May 2005
Chapter
10
1764 Controller I/O on
MicroLogix 1500 Controllers
Expansion I/O for the MicroLogix 1500 controllers is
accomplished with the 1769 Compact I/O modules.
For more information on wiring the 1769
Compact I/O modules, see Chapter 11.
IMPORTANT
1764-24AWA
Input Terminals
L2
Terminal Groupings
NOT AC
IN 1
USED COM 0
NOT
USED
IN 0
IN 3
IN 4
IN 6
AC
IN 2 COM 1 IN 5
AC
IN 9
COM 2
IN 7
IN 8
IN 11
In put Gr oup
Group 0
Group 1
Group 2
IN 10
Common Termin al
AC COM 0
AC COM 1
AC COM 2
In put Termin al
I/0 through I/3
I/4 through I/7
I/8 through I/11
L1
L2 L1
“NOT USED” terminals are not intended for use as connection points.
Output Terminals
CR
CR
L2
Terminal Groupings
(Lo)
VAC VAC/ VAC/ VAC/ VAC/ VAC/
NEUT VDC 0 VDC 1 VDC 2 VDC 3 VDC 4 OUT 5 OUT 7 OUT 8 OUT 10
VAC/
120/240 EARTH
OUT 0 OUT 1 OUT 2 OUT 3 OUT 4 OUT 6
OUT 9 OUT 11
VDC 5
VAC GND
(Hi)
L1
1
CR
CR
CR
CR
Out put Gr oup
Group 0
Group 1
Group 2
Group 3
Group 4
Group 5
Voltage Term inal
VAC/VDC 0
VAC/VDC 1
VAC/VDC 2
VAC/VDC 3
VAC/VDC 4
VAC/VDC 5
Ou tput Terminal
O/0
O/1
O/2
O/3
O/4 through O/7
O/8 through O/11
Publication CIG-WD001B-EN-P - May 2005
10-2
1764 Controller I/O on MicroLogix 1500 Controllers
1764-24BWA - Sinking Inputs
Input Terminals
Terminal Groupings
+24V
DC
IN 1
POWER
OUT COM 0
COM
IN 0
IN 3
IN 2
IN 4
DC
IN 5
COM 1
-DC
DC
COM 2
IN 6
IN 7
IN 9
IN 8
In put Gr oup
Group 0
Group 1
Group 2
IN 11
IN 10
Common Termin al
DC COM 0
DC COM 1
DC COM 2
In put Termin al
I/0 through I/3
I/4 through I/7
I/8 through I/11
+DC
Output Terminals
CR
CR
Terminal Groupings
L2
(Lo)
VAC VAC/ VAC/ VAC/ VAC/ VAC/
OUT 5 OUT 7 OUT 8 OUT 10
NEUT VDC 0 VDC 1 VDC 2 VDC 3 VDC 4
VAC/
120/240 EARTH
VAC GND OUT 0 OUT 1 OUT 2 OUT 3 OUT 4 OUT 6 VDC 5 OUT 9 OUT 11
(Hi)
CR
L1
CR
CR
Out put Gr oup
Group 0
Group 1
Group 2
Group 3
Group 4
Group 5
Voltage Term inal
VAC/VDC 0
VAC/VDC 1
VAC/VDC 2
VAC/VDC 3
VAC/VDC 4
VAC/VDC 5
Ou tput Terminal
O/0
O/1
O/2
O/3
O/4 through O/7
O/8 through O/11
CR
1764-24BWA - Sourcing Inputs
Input Terminals
Terminal Groupings
+24V
POWER DC IN 1
OUT COM 0
COM
IN 0
IN 2
IN 3
IN 4
IN 6
DC
IN 5
COM 1
DC
IN 9
COM 2
IN 7
IN 8
In put Gr oup
Group 0
Group 1
Group 2
IN 11
IN 10
Common Termin al
DC COM 0
DC COM 1
DC COM 2
In put Termin al
I/0 through I/3
I/4 through I/7
I/8 through I/11
+DC -DC
Output Terminals
CR
L2
CR
Terminal Groupings
(Lo)
VAC VAC/ VAC/ VAC/ VAC/ VAC/
NEUT VDC 0 VDC 1 VDC 2 VDC 3 VDC 4 OUT 5 OUT 7 OUT 8 OUT 10
120/240 EARTH
VAC/
OUT 0 OUT 1 OUT 2 OUT 3 OUT 4 OUT 6
OUT 9 OUT 11
VAC GND
VDC 5
L1
(Hi)
Publication CIG-WD001B-EN-P - May 2005
CR
CR
CR
CR
Out put Gr oup
Group 0
Group 1
Group 2
Group 3
Group 4
Group 5
Voltage Term inal
VAC/VDC 0
VAC/VDC 1
VAC/VDC 2
VAC/VDC 3
VAC/VDC 4
VAC/VDC 5
Ou tput Terminal
O/0
O/1
O/2
O/3
O/4 through O/7
O/8 through O/11
1764 Controller I/O on MicroLogix 1500 Controllers
10-3
1764-28BXB - Sinking Inputs
Input Terminals
-DC
+DC
-DC
+DC
Terminal Groupings
NOT DC
IN 1
USED COM 0
NOT
IN 0
USED
IN 3
IN 4
DC
IN 5
COM 1
IN 2
DC IN 9
COM 2
IN 6
IN 7
IN 11 IN 13 IN 15
IN 10 IN 12 IN 14
IN 8
In put Gr oup
Group 0
Group 1
Group 2
Common Termin al
DC COM 0
DC COM 1
DC COM 2
In put Termin al
I/0 through I/3
I/4 through I/7
I/8 through I/15
Out put Gr oup
Voltage Term inal
Ou tput Terminal
Group 0
Group 1
Group 2
Group 3
Group 4
VAC/VDC 0
VAC/VDC 1
VDC 2, VDC COM 2
VAC/VDC 3
VAC/VDC 4
O/0
O/1
O/2 through O/7
O/8 and O/9
O/10 and O/11
“NOT USED” terminals are not intended for use as connection points.
Output Terminals (FET Outputs are Sourcing Only)
CR
CR
CR
Terminal Groupings
-DC
COM VAC/ VAC/ VDC 2 OUT 3 OUT 5 OUT 7 VAC/ OUT 9 OUT 10
VDC 0 VDC 1
VDC 3
+24v EARTH OUT 0 OUT 1 OUT 2 OUT 4 OUT 6 VDC OUT 8 VAC/ OUT 11
COM 2
GND
VDC 4
CR
+DC
CR
CR
Outputs 2 - 7 are FET outputs
1764-28BXB - Sourcing Inputs
Input Terminals
+DC
-DC
+DC
-DC
NOT DC
IN 1
USED COM 0
NOT IN 0
USED
IN 3
IN 2
IN 4
IN 6
DC
IN 5
COM 1
DC IN 9
COM 2
IN 7
IN 8
IN 11 IN 13 IN 15
IN 10 IN 12 IN 14
Terminal Groupings
In put Gr oup
Group 0
Group 1
Group 2
Common Termin al
DC COM 0
DC COM 1
DC COM 2
In put Termin al
I/0 through I/3
I/4 through I/7
I/8 through I/15
Out put Gr oup
Voltage Term inal
Ou tput Terminal
Group 0
Group 1
Group 2
Group 3
Group 4
VAC/VDC 0
VAC/VDC 1
VDC 2, VDC COM 2
VAC/VDC 3
VAC/VDC 4
O/0
O/1
O/2 through O/7
O/8 and O/9
O/10 and O/11
“NOT USED” terminals are not intended for use as connection points.
Output Terminals (FET Outputs are Sourcing Only
CR
CR
Terminal Groupings
CR
-DC
VAC/ VAC/
VAC/
COM
VDC 2 OUT 3 OUT 5 OUT 7
OUT 9 OUT 10
VDC 0 VDC 1
VDC 3
+24V
+DC
VDC
VAC/
EARTH
OUT 0 OUT 1 OUT 2 OUT 4 OUT 6
OUT 8
OUT 11
COM 2
VDC 4
GND
CR
CR
CR
Outputs 2 - 7 are FET outputs
Publication CIG-WD001B-EN-P - May 2005
10-4
1764 Controller I/O on MicroLogix 1500 Controllers
Notes:
Publication CIG-WD001B-EN-P - May 2005
Chapter
11
1769 Compact I/O Modules
1769-HSC – Differential Encoder applications
1769-HSC – Discrete Device applications
Cable(1)
+VDC
+VDC
VS
COM
GND
Power
Supply
COM
Proximity Sensor
Power
Supply
VS
A1(+)
OUT
A1(–)
COM
Allen-Bradley 845H
Series differential
encoder
A
A1(+)
A
A1(–)
B
B1(+)
B
B1(–)
Z
Z1(+)
Z
Z1(–)
VS
Solid-State
Switch
OUT
R
1
B1(+)
COM
B1(–)
Z1(+)
Z1(–)
COM
Photo-electric Sensor
with Open Collector
Sinking Output
Shield
shield/housing
Connect only if housing is electronically isolated from
the motor and ground.
OUT
VS
Module Inputs
Earth
Module Inputs
1. Refer to your encoder manual for proper cable type. The type of cable used should be twisted pair, individually
shielded cable with a maximum length of 300m (1000 ft.).
1. External resistors are required if they are not internal to the sensor. The pull-up
resistor (R) value depends on the power supply value. The table below shows the
maximum resistor values for typical supply voltages. To calculate the maximum resistor
value, use the following formula:
( V dc – Vmin)
R = ---------------------------------------Imin
where: R = maximum pull-up resistor value
Vdc = power supply voltage
Vmin = 2.6V dc
Imin = 6.8 mA
Power Supply Voltage (V dc)
Maximum Pull-Up Resistor Value (a)
5V dc
35 2 Ω
12 V dc
1 38 2 Ω
24 V dc
3 14 7 Ω
(a) Resistance values may change, depending on your application. The
minimum resistor (R) value depends on the current sinking capability
of the sensor. Refer to your sensor's documentation.
1
Publication CIG-WD001B-EN-P - May 2005
11-2
1769 Compact I/O Modules
1769-HSC – Output Device applications
OUT DC
CR
A0B0Z0A1B1Z1-
Cable1
+DC
OUT 0 +5/24VDC
OUT 1
OUT 2
OUT 3
OUT
DC COM
1769-HSC – Single-Ended Encoder applications
+VDC
VS
GND
CR
COM
R
CR
Power
Supply
(2)
A1(+)
A
A1(–)
A0+
B
Allen-Bradley 845H
Series single-ended
encoder
B0+
B1(+)
B1(–)
Z1(+)
Z
Z1(–)
+5/24V dc
Z0+
Shield
shield/housing
Connect only if housing is electronically isolated from
the motor and ground.
A1+
Earth
Module Inputs
B1+
1. Refer to your encoder manual for proper cable type. The type of cable used should
be twisted pair, individually shielded cable with a maximum length of 300m (1000ft).
Z1+
2. External resistors are required if they are not internal to the sensor. The pull-up
resistor (R) value depends on the power supply value. The table below shows the
maximum resistor values for typical supply voltages. To calculate the maximum resistor
value, use the following formula:
-DC
( V dc – Vmin)
R = ---------------------------------------Imin
where: R = maximum pull-up resistor value
Vdc = power supply voltage
Vmin = 2.6V dc
Imin = 6.8 mA
Power Supply Voltage (V dc)
Maximum Pull-Up Resistor Value (a)
5V dc
35 2 Ω
12 V dc
1 38 2 Ω
24 V dc
3 14 7 Ω
(a) Resistance values may change, depending on your application. The minimum resistor (R)
value depends on the current sinking capability of the sensor. Refer to your sensor's documentation.
1769-IA16
1769-IA8I
L1a
L1
100/120V ac
IN 0
IN 1
AC
COM 0
L2a
IN 2
IN 0
L1b
IN 3
IN 4
100/120V ac
IN 5
IN 6
100/120V ac
AC
COM 1
L2b
IN 7
IN 1
L1c
IN 8
IN 9
100/120V ac
IN 10
IN 11
L2c
IN 12
AC
COM 2
IN 2
IN 13
IN 14
IN 15
L2
AC
COM
AC
COM
Commo ns are
connected
internally.
AC
COM3
AC
COM4
AC
COM5
AC
COM6
AC
COM7
NC
Publication CIG-WD001B-EN-P - May 2005
IN 3
IN 4
IN 5
IN 6
IN 7
NC
1769 Compact I/O Modules
1769-IF4 – Differential Inputs applications
Belden 8761 cable (or equivalent)
analog source
V/I in 0 ANLG Com
V/I in 1 ANLG Com
V/I in 2 ANLG Com
V/I in 3 ANLG Com
dc NEUT
I in 0+
V in 1 +
I in 1+
V in 2 +
–
earth ground the
shield locally at
the module
1769-IF4 Terminal Block
Signal
V in 0 +
V/I in 0 I in 0 +
ANLG Com
V in 1 +
V/I in 1 I in 1 +
ANLG Com
V in 2 +
V/I in 2 I in 2 +
ANLG Com
V in 3 +
V/I in 3 I in 3 +
ANLG Com
+24V dc
dc NEUT
+
Differential
Voltage
Transmitter
– Supply +
+
V in 0 +
1769-IF4 – Mixed Transmitter Type applications
Single-ended
Voltage
Transmitter
–
+ Signal
–
–
Differential Signal
Current
+
Transmitter
– Supply +
I in 2+
V in 3 +
2-Wire
Current
Transmitter
I in 3+
+24V dc
+
-
External 24V dc
Power Supply(1)
(optional)(2)
11-3
Sensor/
Transmitter
Supply
Signal
+
+
–
External 24V dc
Power Supply(1)
(optional)(2)
+
–
1. The external power supply must be rated Class 2, with a 24V dc range of 20.4 to 26.4V dc and 60 mA minimum.
2. Series B and later modules provide this option.
1. The external power supply must be rated Class 2, with a 24V dc range of 20.4 to 26.4V dc and 60 mA minimum.
2. Series B and later modules provide this option.
1769-IF4 – Single-Ended Sensor/Transmitter Type applications
Sensor/ +
Transmitter Supply
1769-IF4I – Differential Inputs applications
1769-IF4 Terminal Block
Current
Transmitter
+
Signal
Voltage
Transmitter
+ Ground
Signal
Voltage
Transmitter
+ Ground
Signal
V in 0 +
V/I in 0 I in 0 +
ANLG Com
V in 1 +
V/I in 1 I in 1 +
ANLG Com
V in 2 +
V/I in 2 I in 2 +
ANLG Com
V in 3 +
V/I in 3 I in 3 +
ANLG Com
+24V dc
dc NEUT
Belden 8761 cable
(or equivalent)
analog source
External 24V dc
+
Power Supply(1)
(optional)(2)
1. The external power supply must be rated Class 2, with a 24V dc range of 20.4 to 26.4V dc and 60 mA minimum.
2. Series B and later modules provide this option.
Publication CIG-WD001B-EN-P - May 2005
11-4
1769 Compact I/O Modules
1769-IF4I – Mixed Transmitter Type applications
1769-IF4I – Single-Ended Sensor/Transmitter Type applications
1769-IF4I Terminal Block
Sensor/ +
Transmitter Supply
Ch0+
Sensor/ +
Transmitter
Supply -
N/C
Current
Transmitter
+
Signal
Ch0_iRtn
Current
Transmitter
Signal
+
N/C
Ch0Ch1+
N/C
Voltage Transmitter
Ch1_iRtn
Voltage Transmitter
N/C
Ch1-
+
Ground
Signal
+
Ground
Signal
Ch2+
N/C
+ Ground
Voltage Transmitter
Ch2_iRtn
Voltage Transmitter
N/C
Signal
+
Ch2-
Ground
Signal
Ch3+
N/C
Ch3_iRtn
N/C
Differential
Voltage
Transmitter
Ch3-
+
Signal
_
+
1769-IF8 – Differential Inputs applications
Belden 8761 cable (or equivalent)
analog source
–
V in 0+
V/I in 0-
+
I in 0+
ANLG Com
I in 1+
ANLG Com
V in 2+
V/I in 2-
I in 2+
ANLG Com
V in 3+
V/I in 3-
I in 3+
ANLG Com
NC
Publication CIG-WD001B-EN-P - May 2005
NC
V in 4+
V/I in 4-
I in 4+
ANLG Com
V in 1+
V/I in 1-
–
V in 5+
V/I in 5-
earth ground the
shield locally at
the module
I in 5+
ANLG Com
V in 6+
V/I in 6-
I in 6+
ANLG Com
V in 7+
V/I in 7-
I in 7+
ANLG Com
NC
NC
+
1769 Compact I/O Modules
1769-IF8 – Mixed Transmitter Type applications
Single-ended
Voltage
Transmitter
–
V in 0 +
V/I in 0 -
+
Differential
Voltage
Transmitter
– Supply +
Current
Transmitter
Signal
V in 0 +
V/I in 0 -
+
I in 0 +
AN LG C o m
V in 1 +
V/I in 1 -
–
+ Ground
V in 2 +
V/I in 2 -
V in 2 +
I in 2 +
AN LG C o m
Voltage
Transmitter
+ Ground
V in 3 +
V in 3 +
Signal
V/I in 3 -
+
I in 1 +
AN LG C o m
Signal
V/I in 2 -
I in 2 +
ANLG Com
Signal
V/I in 1 -
Voltage
Transmitter
I in 1 +
ANLG Com
–
Sensor/
Transmitter
Supply
1769-IF8 Terminal Block
Sensor/Trans +
mitter
Supply
I in 0 +
ANLG Com
V in 1 +
+ Signal
Differential Signal
Current
+
Transmitter
– Supply +
2-Wire
Current
Transmitter
1769-IF8 – Single-Ended Sensor/Transmitter Type applications
1769-IF8 Terminal Block
Signal
11-5
I in 3 +
V/I in 3 -
ANLG Com
NC
NC
AN LG C o m
I in 3 +
NC
NC
Wiring for channels 4-7 are identical.
+
–
Wiring for channels 4-7 are identical.
1769-IF4XOF2 – Analog Output Device applications
1769-IF4XOF2 – Differential Input applications
1769-IF4XOF2 Terminal Block
Voltage Load
earth ground
Current Load
V in 0+
I in 0+
V/I in 0 V in 1+
I in 1+
V/I in 1V in 2+
I in 2+
V/I in 2V in 3+
I in 3+
V/I in 3ANLG Com
ANLG Com
V out 0+
I out 0+
V out 1+
I out 1 +
Belden 8761 cable (or equivalent)
V in 1+
V/I in 1 I in 1+
V in 3+
V/I in 3 I in 3+
ANLG Com
V out 1+
I out 1+
V in 0+
V/I in 0-
+
I in 0+
–
V in 2 +
V/I in 2I in 2+
differential voltage
transmitter
earth ground the
shield locally at
the module
ANLG Com
V out 0+
I out 0+
earth ground
Publication CIG-WD001B-EN-P - May 2005
11-6
1769 Compact I/O Modules
1769-IF4XOF2 – Mixed Transmitter Type applications
1769-IF4XOF2 Terminal Block
Signal
Single-ended
Voltage
Transmitter
+
–
V in 0+
I in 0+
V/I in 0 V in 1+
I in 1+
V/I in 1V in 2+
I in 2+
V/I in 2V in 3+
I in 3+
V/I in 3ANLG Com
ANLG Com
V out 0+
I out 0+
V out 1+
I out 1 +
+
Differential
Signal
Voltage
Transmitter –
– Supply +
+
Differential Signal
Current
Transmitter –
– Supply +
Signal
2-Wire
Current
Transmitter +
Sensor/
+
Transmitter
Power Supply(1) –
1769-IF4XOF2 – Single-Ended Sensor/Transmitter applications
Sensor/
Transmitter
Power
Supply(1)
1769-IF4XOF2 Terminal Block
+
+
Current
Transmitter
Signal
Voltage Transmitter
+
Ground
Signal
(1) The sensor power supply must be rated Class 2.
V in 0+
I in 0+
V/I in 0 V in 1+
I in 1+
V/I in 1V in 2+
I in 2+
V/I in 2V in 3+
I in 3+
V/I in 3ANLG Com
ANLG Com
V out 0+
I out 0+
V out 1+
I out 1 +
1. The sensor power supply must be rated Class 2.
1769-IM12
1769-IQ16
+DC (sinking)
-DC (sourcing)
L1
IN 0
IN 1
IN 0
IN 2
IN 1
IN 3
IN 2
IN 4
IN 4
IN 6
200/240V ac
IN 7
IN 8
IN 9
IN 10
24V dc
IN 3
IN 5
Note: Do no t use
the NC terminal s
as co nn ec tion
IN 11
IN 5
IN 6
IN 7
+DC (sinking)
-DC (sourcing)
DC
COM 1
NC
NC
NC
L2
AC
COM
NC
IN 9
AC
COM
IN 11
IN 8
Commo ns ar e
co nn ec ted internally.
24V dc
IN 10
IN 13
IN 12
IN 15
-DC (sinking)
+DC (sourcing)
Publication CIG-WD001B-EN-P - May 2005
DC
COM 2
IN 14
-DC (sinking)
+DC (sourcing)
1769 Compact I/O Modules
11-7
1769-IQ16F
+D C (sinking )
-DC (sou rcing)
IN 0
IN 1
IN 2
24V dc
IN 3
IN 4
IN 5
IN 6
IN 7
+D C (sinking )
-DC (sou rcing)
DC
CO M 1
-DC (sinking )
+D C (sou rcin
IN 9
IN 8
IN 11
24V dc
IN 10
IN 13
IN 12
IN 15
DC
CO M 2
-DC (sinking )
+D C (sou rcing)
IN 14
1769-IQ32
+DC (sinking)
-DC (sourcing)
+DC (sinking)
-DC (sourcing)
IN 0
IN 16
IN 1
IN 17
IN 2
IN 18
24V dc
IN 3
IN 20
IN 5
IN 21
IN 22
IN 6
IN 7
+DC (sinking)
-DC (sourcing)
DC
COM 1
IN 23
-DC (sinking)
+DC (sourcing)
+DC (sinking)
-DC (sourcing)
IN 9
IN 10
IN 24
24V dc
IN 26
IN 29
IN 12
IN 28
IN 15
DC
COM 2
-DC (sinking)
+DC (sourcing)
IN 27
IN 13
-DC (sinking)
+DC (sourcing)
DC
COM 3
IN 25
IN 8
IN 11
24V dc
24V dc
IN 19
IN 4
IN 31
IN 14
-DC (sinking)
+DC (sourcing)
DC
COM 4
IN 30
Publication CIG-WD001B-EN-P - May 2005
11-8
1769 Compact I/O Modules
1769-IQ32T
1769-IQ6XOW4
CR
CR
OUT 0
VAC
VDC
L1 or +DC
OUT 1
CR
OUT 3
CR
L2 or -DC
OUT 2
NC
NC
NC
NC
NC
NC
+DC (sinking)
-DC (sourcing)
No te: Do not use the NC
terminals as connection
points.
IN 0
IN 1
24V dc
IN 2
IN 3
-DC (sinking)
+DC (sourcing)
IN 4
DC
COM
IN 5
(1) Surge Suppression - Connecting surge suppressors across your external inductive
load will extend the life of the relay contacts. For additional details, refer to Industrial
Automation Wiring and Grounding Guidelines, Allen-Bradley publication 1770-4.1.
(2) Sinking/Sourcing Inputs - Sourcing/sinking describes the current flow between the
I/O module and the field device. Sourcing input circuits supply (source) current to
sinking field devices. Sinking input circuits are driven by a current sourcing field device.
Europe: DC sinking input and sourcing output module circuits are the commonly used options.
Publication CIG-WD001B-EN-P - May 2005
1769 Compact I/O Modules
1769-IR6 – 2-Wire Potentiometer Interconnection applications
Add Jumper
Cable Shield (to Ground)
Potentiometer
1769-IR6 – 2-Wire RTD applications
Cable Shield (to Ground)
Add Jumper
EXC 3
RTD EXC
EXC 3
RTD EXC
Return
Belden 9501 Shielded Cable
RTN 3
Return
RTD EXC
Return
SENSE 3
SENSE 3
11-9
RTN 3
EXC 4
Belden 9501 Shielded Cable
Add Jumper
Cable Shield (to Ground)
Potentiometer
RTD EXC
EXC 3
SENSE 3
Return
RTN 3
Belden 9501 Shielded Cable
1769-IR6 – 3-Wire Potentiometer Interconnection applications
Cable Shield (to Ground)
EXC 3
Run RTD EXC and sense wires from the module to
potentiometer terminal and tie terminal to one point.
Potentiometer
RTD EXC
Return
RTN 3
Cable Shield (to Ground)
SENSE 3
RTN 3
EXC 3
SENSE 3
RTD EXC
RTD EXC
Sense
Sense
Return
Return
EXC 4
Belden 83503 or 9533 Shielded Cable
EXC 3
Cable Shield (to Ground)
Sense
SENSE 3
RTN 3
1769-IR6 – 3-Wire RTD applications
Belden 83503 or 9533 Shielded Cable
Run RTD EXC and sense wires from the module to
potentiometer terminal and tie terminal to one point.
RTD EXC
Potentiometer
Sense
1769-IR6 – 4-Wire RTD applications
Return
Cable Shield (to Ground)
Belden 83503 or 9533 Shielded Cable
EXC 3
SENSE 3
RTN 3
EXC 4
RTD EXC
RTD EXC
Sense
Sense
Return
Return
Belden 83503 or 9533 Shielded Cable
Leave one sensor wire open.
Publication CIG-WD001B-EN-P - May 2005
11-10
1769 Compact I/O Modules
1769-IT6
CJC sensor
1769-OA16
NC
CJC 0+
IN 0+
+
IN 3+
-
grounded thermocouple
IN 0-
CJC 0-
-
IN 1 +
IN 2+
IN 2-
IN 5+
CR
OUT 2
CR
OUT4
CR
+
IN 4+
IN 4-
OUT6
CR
OUT 3
CR
OUT 5
CR
OUT 7
CR
100 to 240V ac
L2
L1
VAC 2
IN 5-
CJC sensor
CJC 1+
L1
OUT 1
grounded thermocouple
-
CJC 1-
NC
VAC 1
OUT 0
within 10V dc
IN 1-
IN 3-
ungrounded
thermocouple
CR
+
100 to 240V ac
CR
OUT 8
CR
OUT10
CR
OUT 12
CR
OUT 14
OUT 9
CR
OUT11
CR
OUT 13
CR
OUT 15
CR
L2
(1) Surge Suppression - Connecting surge suppressors across your
external load will extend the life of the triac outputs. For additional
details, refer to Industrial Automation Wiring and Grounding
Guidelines, Allen-Bradley publication 1770-4.1.
1769-OA8
1769-OB16
+DC
+VDC
CR
CR
OUT0
OUT2
L1
VAC 1
OUT1
CR
OUT3
CR
CR
OUT 2
100 to 240V ac
CR
OUT4
OUT6
OUT 1
CR
OUT 3
CR
OUT 5
CR
OUT 6
CR
OUT 8
VAC 2
CR
100 to 240V ac
OUT 0
OUT 4
L2
L1
CR
OUT5
CR
OUT 10
OUT7
CR
OUT 12
OUT 7
CR
OUT 9
CR
OUT 11
CR
OUT 13
CR
24V dc (source)
OUT 14
OUT 15
DC COM
-DC
L2
1769-OB16P
+DC
+VDC
CR
OUT 0
CR
OUT 2
OUT 1
CR
OUT 3
CR
OUT 4
OUT 5
CR
OUT 6
CR
OUT 8
OUT 7
CR
OUT 9
CR
OUT 11
CR
OUT 13
CR
24V dc
OUT 10
OUT 12
OUT 14
OUT 15
DC COM
-DC
Publication CIG-WD001B-EN-P - May 2005
1769 Compact I/O Modules
11-11
1769-OB32
1769-OB8
OUT 0
OUT 2
DC COM
1
DC -
NC
NC
NC
CR
OUT 4
CR
OUT 6
DC COM
2
DC+
+VDC 1
OUT 1
Tr an sient Pu lse Duration as a Function of Load Curren
OUT 3
t
CR
NC
Time - Duration of Transient (ms)
CR
NC
NC
DC+
+VDC 2
OUT 5
CR
OUT 7
CR
On-State Load Current (mA)
DC-
Publication CIG-WD001B-EN-P - May 2005
11-12
1769 Compact I/O Modules
1769-OF2
1769-OF4CI
1769-OF2 Terminal Block
Voltage Load
earth ground
Current Load
earth ground
External 24V dc Power +
Supply(1) (optional)(2) -
V out 0 +
I out 0 +
ANLG Com
NC
V out 1 +
I out 1 +
ANLG Com
NC
+24V dc
dc NEUT
1. The external power supply must be rated Class 2, with a 24V dc range of 20.4 to 26.4V dc and 60 mA minimum.
2. Series B and later modules provide this option.
1769-OF4VI
1769-OF8C
I out 0+
ANLG Com
ANLG Com
I out 1+
ANLG Com
I out 2+
ANLG Com
Current Load
I out 3+
ANLG Com
earth ground
External 24V dc Power +
Supply (optional)
I out 4+
ANLG Com
I out 5+
ANLG Com
I out 6+
ANLG Com
I out 7+
dc NEUT
+24V dc
Publication CIG-WD001B-EN-P - May 2005
1769 Compact I/O Modules
1769-OF8V
1769-OV16
+DC
+VDC
ANLG Com
CR
OUT 0
ANLG Com
CR
OUT 2
V out 0+
V out 1+
V out 2+
ANLG Com
ANLG Com
earth ground
OUT 6
CR
OUT 8
Supply (optional)
CR
OUT 7
CR
OUT 9
CR
OUT 11
CR
OUT 13
CR
OUT 10
V out 5+
ANLG Com
-
OUT 3
24V dc (sink)
ANLG Com
External 24V dc Power +
CR
OUT 5
CR
V out 3+
V out 4+
OUT 1
OUT 4
ANLG Com
Voltage Load
11-13
V out 6+
OUT 12
ANLG Com
V out 7+
OUT 14
dc NEUT
OUT 15
+24V dc
DC COM
-DC
1769-OV32T
1769-OW16
OUT 0
CR
CR
VAC-VDC
1
L1 or +DC
OUT 1
CR
OUT 3
CR
OUT 2
OUT 4
OUT 5
OUT 6
OUT 7
CR
L2 or -DC
VAC-VDC
2
L1 or +DC
OUT 9
CR
OUT 11
CR
OUT 8
CR
CR
OUT 10
OUT 13
OUT 12
OUT 14
OUT 15
CR
L2 or -DC
(1) Surge Suppression - Connecting surge suppressors across
your external inductive load will extend the life of the relay
contacts. For additional details, refer to Industrial Automation
Wiring and Grounding Guidelines, publication 1770-4.1.
Publication CIG-WD001B-EN-P - May 2005
11-14
1769 Compact I/O Modules
1769-OW8
1769-OW8I
L1a or +DCa
L2a or -DCa
OUT 0
CR
VAC-VDC
1
L1 or +DC
OUT 1
CR
OUT 3
CR
OUT 2
CR
OUT 0
VAC-VDC
0
L1b or +DCb
L2 or -DC
L2b or -DCb
OUT 1
VAC-VDC
1
L1c or +DCc
VAC-VDC
2
L1 or +DC
L2 or -DC
CR
OUT 4
CR
OUT 6
OUT 5
CR
L2c or -DCc
OUT 2
VAC-VDC
2
OUT 7
OUT 3
OUT 4
OUT 5
OUT 6
OUT 7
VAC-VDC
3
VAC-VDC
4
VAC-VDC
5
VAC-VDC
6
VAC-VDC
7
NC
NC
Publication CIG-WD001B-EN-P - May 2005
Chapter
12
1771 I/O Modules
1771-CFM
+
+
n.c.
n.c.
G0 Ret
G1 Ret
+
F0 500mV
50
mV
F0 In
F1 500mV
+ 500
mV
F1 In
dc 1 Ret
dc 2 Ret
+
F2 500mV
Prox
+
Cu V 1 Ret
Out 2
Cu V 2 Ret
TTL
+
+
Chs Gnd
5V Com
G0
G1
F0 TTL
F0 Ret
F1 TTL
F1 Ret
+24V 1
+24V 2
F2 TTL
F2 Ret
F3 TTL
F3 Ret
G2
G3
Channel
No. 3
Line 1
Line 1
Shield
Shield
Line 2
Line 2
Blue
Channel
No. 1
Channel
No. 4
Line 1
Shield
Shield
Line 2
Clear
Channel
No. 2
Line 2
Terminator Resistor
(Cat. No. 1770-XS or 1770-XT)
150 ohm 0.5 W
1770-CD Twinaxial cable
Terminals of field wiring arm of 1770-AS adapter module
Cu V dc 1
+
F3 In
G2 Ret
G3 Ret
Out 0
+
F3 500mV
+
F2 In
1771-DA
Terminator Resistor
(Cat. No. 1770-XT)
150 ohm 0.5 W
Out 1
Blue
Shield
Clear
Cu V dc 2
Out 3
NOTE: Absence of a terminator resistor can cause block transfer errors
1771-DB
Ports 1 and 2 can be configured for RS-232, RS-422 and RS-485 communications.
pin configurations for these modes are listed in the table below.
DH-485 port
Port 2
Port 1
Pin
RS-232
RS-422
RS-485
1
chassis/shield
chassis/shield
chassis/shield
2
TXD
N/A 2
N/A 2
3
RXD
N/A 2
N/A 2
4
RT S
N/A 2
N/A 2
5
CTS
N/A 2
N/A 2
6
DSR
N/A 2
N/A 2
7
common
common
common
8
DCD
N/A 2
N/A 2
9
common
common
common
10
common
common
common
14
N/A 1
TXD
TXD/RXD
16
N/A 1
RXD
N/A 2
18
N/A 1
RXD'
N/A 2
20
DTR
N/A 2
N/A 2
25
N/A 1
TXD'
TXD'/RXD'
1- These pins are not a No Connection (N/C). In RS-232 mode, the RS-422 and RS-485
load is still present and should not be connected to any device in this mode.
2- In RS-422 and RS-485 modes, these pins are still connected to their RS-232 drivers
and receivers. Do not use these pins in either RS-422 or RS-485 mode.
Important:
1
Pins 1 1, 12, 13, 15, 17, 19, 21, 22, 23 and 24 are a No Connection (N/C)
Publication CIG-WD001B-EN-P - May 2005
1771 I/O Modules
(Clear)
I/O Cable
Line 1
(Blue)
Line 2
(Clear)
Shield
(Blue)
Line 1
Mating Connector
+
Connector on 1771-DCM
Install a 150 ohm 1/2 watt resistor
when the 1771-DCM simulates the
last I/O chassis in a daisy chain.
From TTL Encoder
Shield
Bit 0
Bit 1
B
Bit 2
A (+) (-)
C 845A Gray
D Absolute
E Encoder
F
G
H
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
L1
ac Out
Triac
switching
circuit
+V dc
Out 0
Out 1
Out 2
Out 3
Out Com
n.c.
n.c.
n.c.
n.c.
n.c.
Out Com
In 0
In 1
In 2
In 3
In 4
In 5
In 6
In 7
In Com
1771-DS (WF)
10-27V dc
In 0
In 0 Com
In 1
In 1 Com
In 2
In 2 Com
In 3
In 3 Com
In 4
In 4 Com
In 5
In 5 Com
In 6
In 6 Com
In 7
In 7 Com
n.c.
n.c.
Out Com
connected
internally
+
1771-DW (WA)
+
5-27V dc
n.c.
+
In 0
+
+
In 1
In 2
+
In 3
+
In 4
+
In 5
+
In 6
n.c.
+
n.c.
1771-DR (WG)
+
12-24V dc
+V dc
+
1771-DL (WB)
TTL in, 5-24V dc out
Bit 0 +
+V dc 1
Bit 0 Out 0
Bit 1 +
Out 1
Bit 1 Out 2
Bit 2 +
Out 3
Bit 2 Com 1
Bit 3 +
Com 1
Bit 3 n.c.
Bit 4 +
+V dc 2
Bit 4 Out 4
Bit 5 +
Out 5
Bit 5 Out 6
Bit 6 +
Out 7
Bit 6 Com 2
Bit 7 +
Com 2
Bit 7 n.c.
Bit 8 +
Bit 10 +
Bit 8 Bit 10 Bit 9 +
Bit 11+
Bit 9 Bit 11 +5V dc
5V Com
From Encoder
Line 2
1771-DE (WG)
+
1771-DCM
Com
+
1771-E1 (WF)
1771-E2 (WF)
1771-E3 (WF)
1771-E4 (WF)
Ch 1
Ch 2
Com
Ch 3
Ch 4
Com
Ch 5
Ch 6
Com
Ch 7
Ch 8
Com
Anlg Out
Com
+15V dc
-15V dc
dc Com
n.c.
Ch 1 +
Ch 1 Ch 2 +
Ch 2 Ch 3 +
Ch 3 Ch 4 +
Ch 4 Ch 5 +
Ch 5 Ch 6 +
Ch 6 Anlg Out
Com
+15V dc
-15V dc
dc Com
n.c.
Ch 1 +
Ch 1 Ch 2 +
Ch 2 Ch 3 +
Ch 3 Ch 4 +
Ch 4 Ch 5 +
Ch 5 Ch 6 +
Ch 6 Anlg Out
Com
+15V dc
-15V dc
dc Com
n.c.
Ch 1 +
External loop power needed.
Publication CIG-WD001B-EN-P - May 2005
External loop power needed.
Ch 2 +
Ch 2 Ch 3 +
Ch 3 Ch 4 +
+
Ch 4 -
External loop power needed.
+
+15V dc
To 1771 IF
+
+
To 1771 IF
+
+
+
To 1771 IF
Ch 1 -
+
12-2
-15V dc
n.c.
Com
1771 I/O Modules
1771-IA (WA)
+
+
1771-ES (WB)
+15V dc
Ch A +
n.c.
Ch A -
Anlg Out
Ch B +
Anlg Ret
Ch B -
15V Com
120V ac/dc
n.c.
In 0
In 0
In 1
In 1
In 2
In 2
Marker + -15V dc
In 3
In 3
Marker - H Done
In 4
In 4
Servo
Drive
+
+V (DD)
In 5
In 5
Jog R
Drv Dsbl
In 6
In 6
Home
-V (DD)
In 7
In 7
H Stop
Tach +
L2
L2
Com In
Tach -
L2 3 terminals are
L2 2 terminals are L2 1 terminals are L2 0 terminals are
connected internally. connected internally. connected internally. connected internally.
1771-IAN (WN)
1771-IB (WA)
120V ac/dc
In 01
In 03
In 05
In 07
L2 0
In 11
In 13
In 15
In 17
L2 1
In 01
In 03
In 05
In 07
L2 2
In 11
In 13
In 15
In 17
L2 3
10-27V dc
n.c.
In 00
In 02
In 04
In 06
L2 0
L1
In 0
In 1
In 2
In 3
In 10
In 12
In 14
In 16
L2 1
L1
In 4
In 5
In 6
+
In 7
In 00
In 02
In 04
In 06
L2 2
L1
In 10
In 12
In 14
In 16
L2 3
- dc
L1
1771-ICD (WH)
20-60V dc
n.c.
n.c.
n.c.
n.c.
In 00
In 01
In 02
In 03
In 04
In 05
In 06
In 07
In 10
In 11
In 12
In 13
In 14
In 15
In 16
In 17
- dc
1771-IBD (WH)
1771-IDI (WD)
120V ac/dc
In 0A
In 0B
L2
+
In 1B
L2
In 2B
L2
In 3B
L2
In 4A
L2
In 5A
In 5B
L2
In 3A
L2
In 4A
In 4B
In 0B
In 4B
L2
In 5A
L2
In 5B
1771-IC (WA)
50V dc
n.c.
10-30V dc
In 01
In 03
In 05
In 07
-dc 0
In 11
In 13
In 15
In 17
-dc 1
In 01
In 03
In 05
In 07
-dc 2
In 11
In 13
In 15
In 17
-dc 3
In 00
In 02
In 04
In 06
- dc 0
+
In 0
In 1
In 2
In 3
In 10
In 12
In 14
In 16
- dc 1
In 4
+
In 5
In 6
In 7
In 00
In 02
In 04
In 06
- dc 2
+
In 10
In 12
In 14
In 16
- dc 3
+
+
- dc
1771-ID16 (WN)
120V ac/dc
In 2A
L2
In 3A
In 3B
1771-IDO1 (WD)
In 1A
L2
In 2A
In 2B
+
220V ac/dc
In 0A
In 1A
In 1B
10-30V dc
n.c.
n.c.
n.c.
n.c.
In 00
In 01
In 02
In 03
In 04
In 05
In 06
In 07
In 10
In 11
In 12
In 13
In 14
In 15
In 16
In 17
- dc
120V ac/dc
n.c.
n.c.
n.c.
n.c.
In 00
In 01
In 02
In 03
In 04
In 05
In 06
In 07
In 10
In 11
In 12
In 13
In 14
In 15
In 16
In 17
1771-IBN (WN)
-dc 3 terminals are -dc 2 terminials are -dc 1 terminals are -dc 0 terminals are
connected internally. connected internally. connected internally. connected internally.
+
Jog F
Tach
1771-IAD/C (WH)
120V ac/dc
n.c.
+
TTL
Output
Encoder
+V In
1771-IA2 (IA)
12-3
L2
L2 - 00
L2 - 01
L2 - 02
L2 - 03
n.c.
L2 - 04
L2 - 05
L2 - 06
L2 - 07
n.c.
L2 - 10
L2 - 11
L2 - 12
L2 - 13
n.c.
L2 - 14
L2 - 15
L2 - 16
L2 - 17
n.c.
In 00
In 01
In 02
In 03
n.c.
In 04
In 05
In 06
In 07
n.c.
In 10
In 11
In 12
In 13
n.c.
In 14
In 15
In 16
In 17
n.c.
Publication CIG-WD001B-EN-P - May 2005
12-4
1771 I/O Modules
1771-IE (WB)
1771-IF (WB)
1771-IFE (WG) Single Ended
L2 - 2
6
L2 - 3
8
10
14
Ch 5
Ch 3
Ch 7
Not used
Ch 6
Com
Com
Ch 7
Ch 4
Ch 8
Input 6
Ch 8
Com
Com
Input 7
Com
n.c.
Pwr Avbl
Not used
+15V dc
Com
Com
+15V dc
+5V dc
-15V dc
Com
Input 5
16
L2 - 7
18
Not used
20
L2 - 10
22
Input 10
-15V dc
Input 11
24
+5V dc
Input 12
L2 - 12
26
L2 - 13
28
Not used
30
L2 - 14
32
Input 13
34
L2 - 16
36
ac High
Input 14
Input 15
Input 16
Common terminals connected internally.
External loop power needed.
Power available must connect to
common to enable operation.
External loop power needed.
Factory configured for either
voltage or current.
L1
Not used
L2 - 15
Not used
Com
Input 3
+
L2 - 5
L2 - 17
Ch 6
Com
+
12
L2 - 11
Ch 2
Ch 4
Input 4
L2 - 4
L2 - 6
Ch 3
Input 2
Input 1
+
Not Used
Input 0
Com
+
4
Ch 5
Com
+
2
L2 - 1
Ch 1
Ch 2
+
L2 - 0
Ch 1
120V ac
Supply
Ch 1
Ch 2
Ch 3
Ch 4
Com
Ch 5
Ch 6
Ch 7
Ch 8
Com
Ch 9
Ch 10
Ch 11
Ch 12
Com
Ch 13
Ch 14
Ch 15
Ch 16
Com
Com
Each input is compatible with either a voltage signal or current signal sensor
L2
ac Low
Common terminals connected internally.
.
1771-ID16GM
External loop power needed.
Input 17
38
Not used
ac Low
40
L2
(Actual wiring runs in this direction.)
ac Input
NOTES: Maintain isolation between phases to prevent module damage.
Do not use any 1771 ac output modules to drive the 1771-IND16GM input module.
External loop power needed.
Publication CIG-WD001B-EN-P - May 2005
External loop power needed.
1771-IFM (WG)
1771-IFMS (WG)
.
Ch 1 +
Ch 1 Ch 2 +
Ch 2 Com
Ch 3 +
Ch 3 Ch 4 +
Ch 4 Com
Ch 5 +
Ch 5 Ch 6 +
Ch 6 Com
Ch 7 +
Ch 7 Ch 8 +
Ch 8 Com
Com
External loop power needed.
Each input is compatible with either a voltage signal or current signal sensor
If the sensor is Isolated, add a 3rd connection from the sensor to common.
Common terminals connected internally.
Ch 1
Ch 2
Ch 3
Ch 4
Com
Ch 5
Ch 6
Ch 7
Ch 8
Com
Ch 9
Ch 10
Ch 11
Ch 12
Com
Ch 13
Ch 14
Ch 15
Ch 16
Com
Com
Each input is compatible with either a voltage signal or current signal sensor
Common terminals connected internally.
Each input is compatible with either a voltage signal or current signal sensor
If the sensor is Isolated, add a 3rd connection from the sensor to common.
Common terminals connected internally.
Ch 1 +
Ch 1 Ch 2 +
Ch 2 Com
Ch 3 +
Ch 3 Ch 4 +
Ch 4 Com
Ch 5 +
Ch 5 Ch 6 +
Ch 6 Com
Ch 7 +
Ch 7 Ch 8 +
Ch 8 Com
Com
1771-IFF (WG) Differential
.
1771-IFF (WG) Single Ended
.
1771-IFE (WG) Differential
Ch 1 +
Ch 1 -
Ch 1 +
Ch 1 -
Com 1&2
Com 1&2
Ch 2 +
Ch 2 Ch 3 +
Ch 3 -
Ch 2 +
Ch 2 Ch 3 +
Ch 3 -
Com 3&4
Com 3&4
Ch 4 +
Ch 4 Ch 5 +
Ch 5 -
Ch 4 +
Ch 4 Ch 5 +
Ch 5 -
Com 5&6
Com 5&6
Ch 6 +
Ch 6 Ch 7 +
Ch 7 -
Ch 6 +
Ch 6 Ch 7 +
Ch 7 -
Com 7&8
Com 7&8
Ch 8 +
Ch 8 n.c.
Ch 8 +
Ch 8 n.c.
External loop power needed.
External loop power needed.
1771 I/O Modules
1771-IGD (WH)
+5V dc terminals connected internally
In 1
In 2
In 3
In 4
In 5
In 6
In 7
- dc
+
Encoder
Out 1
Com
Com
Ch B
Out 2
Com
Com
Marker
n.c.
Com
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
Com
Marker - n.c.
In 5
n.c.
n.c.
In 6
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
+
TTL
Load
5V dc
Com
12 48V dc
Ch 1 +
Ch 1 Ch 2 +
Ch 2 Ch 3 +
Ch 3 Ch 4 +
Ch 4 n.c.
n.c.
Ch 5 +
Ch 5 Ch 6 +
Ch 6 Ch 7 +
Ch 7 Ch 8 +
Ch 8 -
+
Com
1771-IM (WA)
220V ac/dc
n.c.
1771-IND1
In 0
In 1
In 2
In 3
In 4
In 5
In 6
In 7
L2
1771-IQ (WC)
Where: X = Rack # (1, 2, ...)
Y = Module Group (0-7)
L2
AC Low
+
20
21
+
19
+
18
+
17
+
16
+
15
+
Each is switch selectable as
either a source load or sink load
14
Gnd - 00
Gnd - 01
Gnd - 02
Gnd - 03
n.c.
Gnd - 04
Gnd - 05
Gnd - 06
Gnd - 07
n.c.
Gnd - 10
Gnd - 11
Gnd - 12
Gnd - 13
n.c.
Gnd - 14
Gnd - 15
Gnd - 16
Gnd - 17
n.c.
+
- dc
13
L2
+
In 7
10
11
12
In 7
+
In 6
8
9
In 6
+
6
7
In 5
+
+
In 4
In 5
5
In 4
+
4
L1
AC High
In 3
+
In 3
2
3
In 2
+
In 0
In 2
1
In 1
10-32V dc
In 1
Input
Assignment
In 0
1771-IQ16 (WN)
5-30V dc
+ dc
1771-IN (WA)
24V ac
n.c.
+
Terminal 1 must be connected
to L1 to balance the line in
an ungrounded application.
1771-IMD (WH)
220V ac/dc
n.c.
n.c.
n.c.
n.c.
In 00
In 01
In 02
In 03
In 04
In 05
In 06
In 07
In 10
In 11
In 12
In 13
In 14
In 15
In 16
In 17
L2
External loop power needed.
1XY00
1XY01
1XY02
1XY03
1XY04
1XY05
1XY06
1XY07
1XY10
1XY11
1XY12
1XY13
1XY14
1XY15
1XY16
1XY17
Out 2
Ch B -
Com
12 24V dc
Not used
Not used
Not used
Not used
Input 0
Input 1
Input 2
Input 3
Input 4
Input 5
Input 6
Input 7
Input 8
Input 9
Input 10
Input 11
Input 12
Input 13
Input 14
Input 15
L2
Ch B +
TTL
Load
Limit Sw +5V dc
dc
Load
I/O
Program
Address
Com
Marker + n.c.
- dc
12-24V dc
24V ac/dc
L1
n.c.
n.c.
n.c.
In 00
In 01
In 02
In 03
In 04
In 05
In 06
In 07
In 10
In 11
In 12
In 13
In 14
In 15
In 16
In 17
L2
Out 1
Ch A -
In 4
In 7
dc
Load
1771-IND (WH)
Ch A +
In 3
1771-IL/B (WF)
+
Com
TTL
Output
Encoder
In 2
n.c.
Limit Sw +V dc
In 0
In 1
1771-IK (WB)
Ch A
TTL
24-48V dc
n.c.
TTL
+5V dc
+5V dc
+5V dc
+5V dc
In 00
In 01
In 02
In 03
In 04
In 05
In 06
In 07
In 10
In 11
In 12
In 13
In 14
In 15
In 16
In 17
- dc
+
+
In 0
1771-IJ (WB)
+
TTL
+5V dc
1771-IH (WA)
Each input is compatible with either a voltage signal or current signal sensor.
1771-IG (WC)
12-5
In 00
In 01
In 02
In 03
n.c.
In 04
In 05
In 06
In 07
n.c.
In 10
In 11
In 12
In 13
n.c.
In 14
In 15
In 16
In 17
n.c.
1771-IR/B (WF)
Ch 1 C
Ch 1 B
Ch 1 A
Ch 2 C
Ch 2 B
Ch 2 A
Ch 3 C
Ch 3 B
Ch 3 A
Ch 4 C
Ch 4 B
Ch 4 A
Ch 5 C
Ch 5 B
Ch 5 A
Ch 6 C
Ch 6 B
Ch 6 A
Loop power provided internally.
(Actual wiring runs in this direction.)
Publication CIG-WD001B-EN-P - May 2005
12-6
1771 I/O Modules
1771-IS (WF)
Enable A
Enable B
Enable C
Enable D
Enable E
Enable F
Enable G
Enable H
Enable I
In 0
In 1
In 2
In 3
In 4
In 5
In 6
In 7
n.c.
1771-IV (WA)
12-24V dc
n.c.
12-24V dc
+ dc
In 0
In 0
In 1
In 1
In 2
In 2
In 3
In 3
In 4
In 4
In 5
In 5
In 6
In 7
1771-IVN (WN)
+
- dc
10-30V dc
+ dc 0
In 00
In 02
In 04
In 06
+
+ dc 0
In 01
In 03
In 05
In 07
+
+ dc 1
In 11
In 13
In 15
In 17
+
+ dc 2
In 01
In 03
In 05
In 07
+
+ dc 3
In 11
In 13
In 15
In 17
+
In 6
In 7
- dc
+ dc 1
In 10
In 12
In 14
In 16
+ dc 2
In 00
In 02
In 04
In 06
+ dc 3
In 10
In 12
In 14
In 16
1771-IXE/B (WI)
+dc 3 terminals are +dc 2 terminals are +dc 1 terminals are +dc 0 terminals are
connected internally. connected internally. connected internally. connected internally.
1771-IT (WA)
W1 S4 O4
R3 I3
S3 O3
R2 I2
S2 O2
1771-NB4T (RT41)
R1 I1
S1 O1
S1 thru S4 are connected internally to SH.
Input loop power provided internally if connected as shown for 4.
Publication CIG-WD001B-EN-P - May 2005
In 1 +
In 1 In 2 +
In 2 In 3 +
In 3 In 4 +
In 4 n.c.
n.c.
In 5 +
In 5 In 6 +
In 6 In 7 +
In 7 In 8 +
In 8 -
In 1 +
In 1 In 2 +
In 2 In 3 +
In 3 In 4 +
In 4 n.c.
n.c.
In 5 +
In 5 In 6 +
In 6 In 7 +
In 7 In 8 +
In 8 -
1771-NB4S (RT44)
SH R4 I4
1771-IXHR (WI)
SH R4 I4
W1 S4 O4
R3 I3
S3 O3
R2 I2
S2 O2
S1 thru S4 are connected internally to SH.
R1 I1
S1 O1
1771 I/O Modules
1771-NBRC (RTP4)
SH W2 W3 R8 I8
W1 CR CL S8 O8
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R4 I4
S4 O4
1771-NBSC (RTP4)
R3 I3
R2 I2
S3 O3
S2 O2
R1 I1
S1 O1
1771-NBTC (RTP1)
W1 CR CL S8 O8
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R4 I4
S4 O4
SH W2 W3 R8 I8
W1 CR CL S8 O8
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R3 I3
R2 I2
S3 O3
S2 O2
R1 I1
S1 O1
SH W2 W3 R8 I8
W1 CR CL S8 O8
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R4 I4
S4 O4
R3 I3
R2 I2
S3 O3
S2 O2
R1 I1
S1 O1
SH W2 W3 R8 I8
W1 CR CL S8 O8
R2 I2
S2 O2
R1 I1
S1 O1
R4 I4
S4 O4
R3 I3
S3 O3
R2 I2
S2 O2
R1 I1
S1 O1
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R4 I4
S4 O4
R3 I3
S3 O3
S1 thru S8 are connected internally to SH. External loop power needed.
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R4 I4
S4 O4
R3 I3
R2 I2
S3 O3
S2 O2
R1 I1
S1 O1
S1 thru S8 are connected internally to SH. Input loop power provided internally if connected as shown
for 4 thru 8.
1771-NIV (RTP4 Voltage, RTP3 Current)
W1 CR CL S8 O8
S3 O3
1771-NIS (RTP4)
S1 thru S8 are connected internally to SH. External loop power needed.
SH W2 W3 R8 I8
R3 I3
S1 thru S8 are connected internally to SH. External loop power needed.
1771-NBVC (RTP4 Voltage, RTP3 Current)
W1 CR CL S8 O8
S4 O4
1771-NBV1 (RTP4 Voltage, RTP3 Current)
S1 thru S8 are connected internally to SH.
SH W2 W3 R8 I8
R4 I4
S1 thru S8 are connected internally to SH. Input loop power provided internally if connected as shown
for 4 thru 8.
S1 thru S8 are connected internally to SH. Input loop power provided internally .
SH W2 W3 R8 I8
12-7
1771-NIV1 (RTP4 Voltage, RTP3 Current)
R2 I2
S2 O2
R1 I1
S1 O1
SH W2 W3 R8 I8
W1 CR CL S8 O8
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R4 I4
S4 O4
R3 I3
S3 O3
R2 I2
S2 O2
R1 I1
S1 O1
S1 thru S8 are connected internally to SH. External loop power needed.
Publication CIG-WD001B-EN-P - May 2005
12-8
1771 I/O Modules
1771-NIVR (RTP4)
SH W2 W3 R8 I8
W1 CR CL S8 O8
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R4 I4
1771-NIVT (RTP1 )
R3 I3
S4 O4
S1 thru S8 are connected internally to SH.
R2 I2
S3 O3
R1 I1
S2 O2
SH W2 W3 R8 I8
S1 O1
W1 CR CL S8 O8
External loop power needed.
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
S1 thru S8 are connected internally to SH.
1771-NOC (RTP4 or RTP3)
SH W2 W3 R8 I8
W1 CR CL S8 O8
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R4 I4
R2 I2
S3 O3
S2 O2
R1 I1
SH W2 W3 R8 I8
S1 O1
W1 CR CL S8 O8
S1 thru S8 are connected internally to SH.
W1 CR CL S8 O8
R3 I3
S3 O3
R2 I2
S2 O2
R1 I1
S1 O1
External loop power needed.
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R4 I4
S4 O4
R3 I3
S3 O3
R2 I2
S2 O2
R1 I1
S1 O1
S1 thru S8 are connected internally to SH.
1771-NR (RTP4)
SH W2 W3 R8 I8
S4 O4
1771-NOV (RTP4 or RTP3)
R3 I3
S4 O4
R4 I4
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
R4 I4
S4 O4
1771-NT1 (RTP1 )
R3 I3
S3 O3
R2 I2
S2 O2
R1 I1
SH W2 W3 R8 I8
S1 O1
W1 CR CL S8 O8
S1 thru S8 are connected internally to SH. Input loop power provided internally .
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
S1 thru S8 are connected internally to SH.
1771-NT2 (RTP1)
SH W2 W3 R8 I8
W1 CR CL S8 O8
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
S1 thru S8 are connected internally to SH.
Publication CIG-WD001B-EN-P - May 2005
R4 I4
S4 O4
R3 I3
S3 O3
R2 I2
S2 O2
R1 I1
S1 O1
R4 I4
S4 O4
R3 I3
S3 O3
R2 I2
S2 O2
R1 I1
S1 O1
1771 I/O Modules
120V ac
L1
Out 0
L1 terminals connected internally
Out 1
Out 2
Out 3
Out 4
Out 5
Out 6
Out 7
L2
120/220V ac
L1 0
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
Out 07
n.c.
L2 (neutral)
+
10-30V dc
+ dc 0
Out 01
Out 03
Out 05
Out 07
Out 00
Out 02
Out 04
Out 06
Comm 0
Out 10
Out 12
Out 14
Out 16
Comm 1
Out 00
Out 02
Out 04
Out 06
Comm 2
Out 10
Out 12
Out 14
Out 16
Comm 3
+ dc 1
Out 11
Out 13
Out 15
Out 17
+ dc 2
Out 01
Out 03
Out 05
Out 07
+ dc 3
Out 11
Out 13
Out 15
Out 17
L1 1
Out 11
Out 13
Out 15
Out 17
Out 10
Out 12
Out 14
Out 16
n.c.
L2 (neutral)
L1 2
Out 01
Out 03
Out 05
Out 07
Out 00
Out 02
Out 04
Out 06
n.c.
1771-OB (WA)
Out 1
Out 2
Out 3
Out 4
Out 5
Out 6
Out 7
- dc
L2 (neutral)
+
+
10-60V dc
+ dc
+ dc
+ dc
+ dc
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
Out 07
Out 10
Out 11
Out 12
Out 13
Out 14
Out 15
Out 16
Out 17
- dc
+
L2 (neutral)
1771-OD (WD)
42-53V dc
+ dc
Out 0
+
+
Out 0
1771-OC (WA)
+
1771-OBD (WH)
10-27V dc
+ dc
L1 3
Out 11
Out 13
Out 15
Out 17
Out 10
Out 12
Out 14
Out 16
n.c.
+dc terminals not connected internally
10-40V dc
+ dc
+ dc
+ dc
+ dc
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
Out 07
Out 10
Out 11
Out 12
Out 13
Out 14
Out 15
Out 16
Out 17
- dc
120V ac
L1
L1
L1
L1
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
Out 07
Out 10
Out 11
Out 12
Out 13
Out 14
Out 15
Out 16
Out 17
L2
L2 connection optional
1771-OBN (WN)
Common terminals not connected internally
+dc terminals connected internally
1771-OBDS (WH)
1771-OAN (WN)
+dc terminals connected internally
1771-OAD (WH)
L1 terminals not connected internally
1771-OA (WA)
12-9
120V ac
120V ac
Out 0A
+
Out 0B
Out 1
Out 1A
Out 2
Out 1B
Out 3
Out 2A
Out 4
Out 2B
Out 5
Out 3A
Out 6
Out 3B
Out 7
Out 4A
- dc
Out 4B
L2
L2
L2
L2
L2
Out 5A
Out 5B
1771-OD16 (WN)
L2
L1 - 00
L1 - 01
L1 - 02
L1 - 03
n.c.
L1 - 04
L1 - 05
L1 - 06
L1 - 07
n.c.
L1 - 10
L1 - 11
L1 - 12
L1 - 13
n.c.
L1 - 14
L1 - 15
L1 - 16
L1 - 17
n.c.
Out 00
Out 01
Out 02
Out 03
n.c.
Out 04
Out 05
Out 06
Out 07
n.c.
Out 10
Out 11
Out 12
Out 13
n.c.
Out 14
Out 15
Out 16
Out 17
n.c.
Publication CIG-WD001B-EN-P - May 2005
1771 I/O Modules
1771-ODD (WN)
1771-ODZ (WD)
120V ac
120V ac
Out 0
L1, 2-3
Out 3
Out 4
L2
L1, 4-5
Out 5
Out 6
L2
L1, 6-7
Ch 1 +
Ch 2
Ch 1 -
Com
Ch 2 +
Ch 3
Ch 2 -
Ch 4
Ch 3 +
Com
Ch 3 -
Pwr Avbl
Ch 4 +
Com
Ch 4 +
L2
Ch 1
+15V dc
n.c.
+
Out 2
-15V dc
n.c.
+5V dc
Com
Out 7
0
Channel 1 (+)
Channel 1 ( )
Out 0
Out 1
Channel 3 (+)
Channel 3 ( )
Out 3
4
5
Channel 4 (+)
Out 5
Channel 4 ( )
Not used
Not used
Out 6
2
3
6
7
B
Out 2
Out 4
Out 7
- dc
Each is an open collector
output with an internal 1k
pull up resistor to +5V.
Field Wiring Arm
Cat. No 1771 WC
1771-OM (WA)
1771-OMD (WH)
220V ac
L1
Out 1
Out 2
Out 3
Out 4
Out 5
Out 6
Out 7
L2
Publication CIG-WD001B-EN-P - May 2005
L1 terminals connected internally
Out 0
220V ac
L1
L1
L1
L1
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
Out 07
Out 10
Out 11
Out 12
Out 13
Out 14
Out 15
Out 16
Out 17
L2
+
TTL
+5V dc
+5V dc
+5V dc
+5V dc
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
Out 07
Out 10
Out 11
Out 12
Out 13
Out 14
Out 15
+
Out 16
Out 17
- dc
Each is an open collector output with
an internal 1k pull up resistor to +5V.
1771-ON (WA)
1771-OJ (WB)
+
TTL
+5V dc
Channel 2 (+)
Channel 2 ( )
1
1771-OGD (WH)
+dc In
+
1771-OG (WC)
+dc Out
Com
Stop
Jog F
Jog R
n.c.
n.c.
n.c.
n.c.
F Rate
R Rate
1771-OND (WH)
24V ac
L1
Out 0
Out 1
Out 2
Out 3
Out 4
Out 5
Out 6
Out 7
L2
L1 terminals connected internally
A
Ground
Common terminals connected internally.
Out 1
1771-OFE1, -OFE2, -OFE3
User
Analog
Device
L2
L1, 0-1
1771-OFE (WC)
+
Out 00
Out 01
Out 02
Out 03
n.c.
Out 04
Out 05
Out 06
Out 07
n.c.
Out 10
Out 11
Out 12
Out 13
n.c.
Out 14
Out 15
Out 16
Out 17
n.c.
L1 - 00
L1 - 01
L1 - 02
L1 - 03
n.c.
L1 - 04
L1 - 05
L1 - 06
L1 - 07
n.c.
L1 - 10
L1 - 11
L1 - 12
L1 - 13
n.c.
L1 - 14
L1 - 15
L1 - 16
L1 - 17
n.c.
1771-OF/B (WB)
+5V dc terminals connected internally
12-10
24V ac
L1
L1
L1
L1
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
Out 07
Out 10
Out 11
Out 12
Out 13
Out 14
Out 15
Out 16
Out 17
L2
Stepper
Translator
and Power
Supply
1771 I/O Modules
Out 0
+
+
+
+
+
+
+
L2
+
n.c.
+
n.c.
+
+
+
Out 3
+
Out 2
+
Out 1
+
n.c.
+
+dc 00
+dc 01
+dc 02
+dc 03
n.c.
+dc 04
+dc 05
+dc 06
+dc 07
n.c.
+dc 10
+dc 11
+dc 12
+dc 13
n.c.
+dc 14
+dc 15
+dc 16
+dc 17
n.c.
+
n.c.
1771-OR (WD)
10-32V dc
+
+
L1
+
20.4-26.4V dc
n.c.
+24V dc
Out 0
Out 1
- dc
- dc
Out 2
Out 3
+24V dc
+24V dc
Out 4
Out 5
- dc
- dc
Out 6
Out 7
+24V dc
n.c.
120V ac
1771-OQ16 (WN)
1771-OVN (WN)
10-30V dc
220V ac
Out 00
Out 01
Out 02
Out 03
n.c.
Out 04
Out 05
Out 06
Out 07
n.c.
Out 10
Out 11
Out 12
Out 13
n.c.
Out 14
Out 15
Out 16
Out 17
n.c.
Out 0A
Out 00
Out 02
Out 04
Out 06
Comm 0
L2
Out 0B
Out 1A
+
L2
Out 1B
Out 2
L2
Out 2B
Out 3A
L2
Out 3B
Out 4A
L2
Out 4B
Out 5A
L2
Out 5B
Out 10
Out 12
Out 14
Out 16
Comm 1
+
Out 00
Out 02
Out 04
Out 06
Comm 2
+
Out 10
Out 12
Out 14
Out 16
Comm 3
+
Out 1
Out 2
Comm
L2
Out 3
Out 4
Comm
L2
Out 5
Out 6
Comm
L2
Out 7
Each output individually
configurable for either
normally open or normally
closed.
Out 00 no
Out 01 no
Out 02 no
Out 03 no
Out 04 no
Out 05 no
Out 06 no
Out 07 no
Out 10 nc
Comm 10
Out 11 no
Out 12 nc
Comm 12
Out 13 no
Out 14 nc
Comm 14
Out 15 no
Out 16 nc
Comm 16
Out 17 no
Out 00
Out 02
Out 04
Out 06
n.c.
Out 10
Out 12
Out 14
Out 16
n.c.
Out 00
Out 02
Out 04
Out 06
n.c.
Out 10
Out 12
Out 14
Out 16
n.c.
Relay
Comm 0
Out 01
Out 03
Out 05
Out 07
L2 (neutral)
Comm 1
Out 11
Out 13
Out 15
Out 17
L2 (neutral)
Comm 2
Out 01
Out 03
Out 05
Out 07
L2 (neutral)
Comm 3
Out 11
Out 13
Out 15
Out 17
L2 (neutral)
1771-OWNA (WN)
Out 00
Out 02
Out 04
Out 06
n.c.
Out 10
Out 12
Out 14
Out 16
n.c.
Out 00
Out 02
Out 04
Out 06
n.c.
Out 10
Out 12
Out 14
Out 16
n.c.
Relay
Comm 0
Out 01
Out 03
Out 05
Out 07
L2 (neutral)
Comm 1
Out 11
Out 13
Out 15
Out 17
L2 (neutral)
Comm 2
Out 01
Out 03
Out 05
Out 07
L2 (neutral)
+ dc 1
Out 11
Out 13
Out 15
Out 17
+ dc 2
Out 01
Out 03
Out 05
Out 07
+ dc 3
Out 11
Out 13
Out 15
Out 17
1771-OX (WC)
Relay
Comm 0
Common terminals are not connected internally
L2
Comm 00
Comm 01
Comm 02
Comm 03
Comm 04
Comm 05
Comm 06
Comm 07
Out 10 no
Out 11 nc
Comm 11
Out 12 no
Out 13 nc
Comm 13
Out 14 no
Out 15 nc
Comm 15
Out 16 no
Out 17 nc
Comm 17
Each output individually configurable for either nc or no
Out 0
Comm
1771-OWN (WN)
Relay
Each output is normally open (no)
1771-OW16/B (WN)
Common terminals are not connected internally
1771-OW (WD)
Relay
+ dc 0
Out 01
Out 03
Out 05
Out 07
+dc terminals not connected internally
1771-OQ (WF)
Common terminals not connected internally
1771-OP (WA)
12-11
Out 0
L2
Comm 1
Out 1
L2
n.c.
n.c.
Comm 2
Out 2
L2
Comm 3
Out 3
L2
Each output individually
configurable for either
normally open or normally
closed.
Comm 3
Out 11
Out 13
Out 15
Out 17
L2 (neutral)
Publication CIG-WD001B-EN-P - May 2005
1771 I/O Modules
A Out 2
+15V dc
+
+
Servo
Valve
+
+
+
Servo
Valve
1771-QI (WF)
+
+
+
+
+
+
+
SH W2 W3 R8 I8
W1 CR CL S8 O8
+
+
+
+
+
+
Valve 1
Amp
Valve 2
Amp
Valve 3
Amp
Valve 4
Amp
+
+
+
In 1+
In 1 In 2 +
In 2 n.c.
In 3 +
In 3 In 4 +
In 4 Out 1 +
Out 1 Out 2 +
Out 2 Out 3 +
Out 3 Out 4 +
Out 4 n.c.
+
+
Valve 1
Amp
Valve 2
Amp
+
+
+
+
+
+
+
+
+
+
1771-QH (WF)
In 1+
In 1 In 2 +
In 2 n.c.
In 3 +
In 3 In 4 +
In 4 Out 1 +
Out 1 Out 2 +
Out 2 Out 3 +
Out 3 Out 4 +
Out 4 n.c.
+
+
+
+
Valve 1
Amp
Valve 2
Amp
Valve 3
Amp
Valve 4
Amp
+
+
+
+
R7 I7
R6 I6
R5 I5
S7 O7
S6 O6
S5 O5
S1 thru S8 are connected internally to SH.
+
+
+
+
Publication CIG-WD001B-EN-P - May 2005
R4 I4
S4 O4
+
+
+
+
+
+
+
+
+
+
1771-QDC (WF)
1771-TCM (RTP1)
+
In 1+
In 1 In 2 +
In 2 n.c.
In 3 +
In 3 In 4 +
In 4 Out 1 +
Out 1 Out 2 +
Out 2 Out 3 +
Out 3 Out 4 +
Out 4 n.c.
+
+
Dig
Intfc
Box
Dig
Intfc
Box
In 1+
In 1 In 2 +
In 2 n.c.
In 3 +
In 3 n.c.
n.c.
Out 1
Out Com
Out 2
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
+
+
+
+
+
Valve 1
Amp
Valve 2
Amp
Valve 3
Amp
Valve 4
Amp
+
+
1771-QD (WF)
Loop 1
+ Gate
- Gate
+ Interr
- Interr
+5V dc
n.c.
Auto/Man
Start
Stop
Jog Fwd
Jog Rev
Input 1
Input 2
I/P Sply
+Analog
-Analog
+15V dc
-15V dc
In Pos
Fault
+
+
+
1771-VHSC (WN)
R3 I3
S3 O3
R2 I2
S2 O2
R1 I1
S1 O1
Ct 0 A Ct 0 B Ct 0 G Ct 1 G Ct 1 B Ct 1 A Ct 2 A Ct 2 B Ct 2 G Ct 3 G Ct 3 B Ct 3 A Out 0
Com 0-1
Out 2
Com 2-3
Out 4
Com 4-5
Out 6
Com 6-7
+
1771-QB (WN)
1771 - WB
Wiring Arm
+
Out 7 no
+
Out 7 nc
5V Com
+5V dc
n.c.
+
L2
Com 6&7
Terminator
(cat. no.
1770 - XT)
+
Out 6 no
L2
Com 6&7
Blue
Shield
Clear
Loop 1 Man Mode
Loop 2 Man Mode
Manual Request
Man Md 1
Man Md 2
Man Rqst
Out 5 no
Out 6 no
Loop 2
+ Gate
- Gate
+ Interr
- Interr
5V Com
n.c.
Auto/Man
Start
Stop
Jog Fwd
Jog Rev
Input 1
Input 2
I/P Com
+Analog
-Analog
15V Com
In Pos
Fault
O/P Sply
-15V dc
+
Out 5 nc
15V Com
L2
Com 4&5
+
Out 4 no
L2
Com 4&5
+
Out 4 no
Loop 1 CV
Loop 2 CV
Mod Com
Out 3 no
+
L2
Com 2&3
Out 3 nc
+
L2
Com 2&3
Loop 1 Tieback
Loop 2 Tieback
+
Out 2 no
+
Out 1 no
Out 2 no
Blue
Shield
Clear
+
Out 1 nc
Blue
Shield
Clear
Loop 2 PV
+
Com 0&1
Loop 1 PV
+
Com 0&1
L2
+
L2
In 1 +
In 1 In 2 +
In 2 TB In 1
TB In 2
A Out 1
+
Out 0 no
+
Relay
1771-PM
+
Relay
Out 0 no
1771-PD (WF)
+
1771-OZL (WD)
+
1771-OYL (WD)
+
12-12
Ct 0 A +
Ct 0 B +
Ct 0 G +
Ct 1 G +
Ct 1 B +
Ct 1 A +
Ct 2 A +
Ct 2 B +
Ct 2 G +
Ct 3 G +
Ct 3 B +
Ct 3 A +
+Vdc 0-1
Out 1
+Vdc 2-3
Out 3
+Vdc 4-5
Out 5
+Vdc 6-7
Out 7
1771 I/O Modules
1771-WS
1771-WS
Connecting Wires from the Junction Box to the
Remote Termination Panel - Using the
Connecting Wires from the Junction Box to the Remote
Termination Panel - With the Module-Generated
+
±
+
±
+
±
±
+
SH R4 I4 R3 I3 R2 I2 R1 I1
+
±
+
±
+
0±30mV Weight Signal ±
±
+
C2 Cal
+
10V Excitation
±
+
0±30mV Weight Signal
±
±
+ C2 Cal
10V Excitation
Sense
Junction Box
To Load Cell
W1 S4 O4 S3 O3 S2 O2 S1 O1
To Load Cell
ATTENTION: The C2-Cal connections
apply only to those applications using
C2 Second-Generation-Calibration
load points
!
!
Junction Box
SH R4 I4 R3 I3 R2 I2 R1 I1
W1 S4 O4 S3 O3 S2 O2 S1 O1
RTP
+
±
+
±
±
+
12-13
ATTENTION: The C2-Cal connections
apply only to those applications using
C2 Second-Generation-Calibration
load points
RTP
I1
± Excitation to junction box
R3
+ Excitation to junction box
R1
I1 on R TP
S3
Shield
I1
± Excitation to junction box
R3
+ Excitation to junction box
S1
Shield
O3
Not Used
R1
± Sense from junction box
S3
Shield
O1
± C2-Cal from junction box 1
I4
Not Used
S1
Shield
O3
Not Used
I2
± Signal from junction box
R4
Not Used
O1
1
± C2-Cal from junction box
I4
Not Used
R2
+ Signal from junction box
S4
Shield
I2
± Signal from junction box
R4
Not Used
S2
Shield
O4
Not Used
R2
+ Signal from junction box
S4
Shield
O2
+ C2-Cal from junction box 1
SH
Ground
S2
Shield
O4
Not Used
I3
R3 on R TP
W1
Not Used
O2
1
+ C2-Cal from junction box
SH
Ground
I3
+ Sense from junction box
W1
Not Used
1 These connections apply only to those applications using C2 Second-Generation-Calibration load points. A sense loop is
required when using C2 Second-Generation-Calibration.
1 These connections apply only to those applications using C2 Second-Generation-Calibration load points.
A sense loop is required when using C2 Second-Generation-Calibration.
1771-sc IM16
1771-WS
Connecting Wires from the Junction Box to the
Remote Termination Panel - With the Voltage
!
ATTENTION: In this configuration, you
must also jumper +excitation to +sense
and +/-excitation to +/-sense in the
junction box.
10V External
Power Supply
+
±
+
±
±
+
+
± Sense
+
± 0±30mV Weight Signal
±
+ C2 Cal
Junction Box
To Load Cell
SH R4 I4 R3 I3 R2 I2 R1 I1
!
W1 S4 O4 S3 O3 S2 O2 S1 O1
ATTENTION: The C2-Cal connections
apply only to those applications using
C2 Second-Generation-Calibration
load points
I1
1 on RTP
R3
Not Used
R1
± Sense from junction box
S3
Shield
S1
Shield
O3
Not Used
O1
± C2-Cal from junction box 1
I4
Not Used
I2
± Signal from junction box
R4
Not Used
R2
+ Signal from junction box
S4
Shield
S2
Shield
O4
Not Used
O2
+ C2-Cal from junction box 1
SH
Ground
I3
+ Sense from junction box
W1
Not Used
In 00In 01In 02In 03n.c.
In 04In 05In 06In 07n.c.
In 10In 11In 12In 13n.c.
In 14In 15In 16In 17n.c.
120/240V ac/dc
In 00
In 01
In 02
In 03
n.c.
In 04
In 05
In 06
In 07
n.c.
In 10
In 11
In 12
In 13
n.c.
In 14
In 15
In 16
In 17
n.c.
1771-sc OMI16 (WN)
120/240V ac
L1 - 00
L1 - 01
L1 - 02
L1 - 03
n.c.
L1 - 04
L1 - 05
L1 - 06
L1 - 07
n.c.
L1 - 10
L1 - 11
L1 - 12
L1 - 13
n.c.
L1 - 14
L1 - 15
L1 - 16
L1 - 17
n.c.
Out 00
Out 01
Out 02
Out 03
n.c.
Out 04
Out 05
Out 06
Out 07
n.c.
Out 10
Out 11
Out 12
Out 13
n.c.
Out 14
Out 15
Out 16
Out 17
n.c.
1 These connections apply only to those applications using C2 Second-Generation-Calibration load points. A sense loop is
required when using C2 Second-Generation-Calibration.
Publication CIG-WD001B-EN-P - May 2005
12-14
1771 I/O Modules
Notes:
Publication CIG-WD001B-EN-P - May 2005
13
Chapter
1790 CompactBlock LDX I/O Modules
IMPORTANT
The catalog numbers included in this chapter are organized
alphabetically according to connector type. The modules
that use D-shell connectors are listed first, followed by the
modules that use terminal blocks.
1790-16BVOX
COM0
I1
I0
19
18
37
16
17
35
36
I3
34
I6
I4
15
13
14
33
I7
I5
I2
30
31
32
I10
COM2
11
12
I8
29
I9
9
10
28
1790-8BV8BX
8
27
I12
I14
I11
7
26
5
6
24
25
I13
3
4
22
23
COM0
I15
1
2
19
18
37
20
21
I1
I3
I0
16
17
36
35
13
14
33
31
32
For inputs 0-7: Sinking inputs - wire Com 1 to Field Power (+) 24V dc, wire Com 0 to Field Power (-) GND
Sourcing inputs - wire Com 1 to Field Power (-) GND, wire Com 0 to Field Power (+) 24V dc
I3
19
18
16
17
I7
I5
I6
I4
15
13
14
11
12
9
10
O2
O1
8
O4
O6
O3
7
O5
5
6
COM0
O7
3
4
36
35
34
33
32
31
30
29
28
27
27
26
5
6
24
25
22
23
O7
3
4
1
2
20
21
26
25
24
23
22
21
O1
O3
O0
O7
O5
O2
O6
O4
O8
COM2
O10
O9
O12
O11
O14
O13
O15
1
2
19
37
7
1790-OB16X
O0
COM2
28
29
8
O6
O5
Sinking outputs -wire Com 2 to Field Power (+) 24Vdc, wire Com 3 to Field Power (-) GND
Note: all Com 3 are internally connected.
1790-8BV8VX
I2
9
10
O4
O3
Sourcing inputs - wire Com1 to Field Power (-) GND, wire Com 0 to Field Power (+) 24V dc
Note: all Com 1 are internally connected.
Note: All Com 1 and Com 3 are internally connected - Com 1 is used for inputs 0-7, Com 3 is used for
inputs 8-15.
I1
30
O2
O1
Sinking inputs - wire Com 1 to Field Power (+) 24V dc, wire Com 0 to Field Power (-) GND
For inputs 8-15: Sinking inputs - wire Com 3 to Field Power (+) 24V dc, wire Com 2 to Field Power (-) GND
Sourcing inputs - wire Com 3 to Field Power (-) GND, wire Com 2 to Field Power (+) 24V dc
I0
11
12
O0
COM2
COM1
COM1
COM3
COM3
COM1
COM1
COM3
COM3
COM1
COM1
COM1
COM1
COM1
COM3
COM3
COM3
COM3
COM3
COM1
COM1
COM3
COM3
COM1
COM1
COM3
COM3
COM1
COM1
COM1
COM1
COM1
COM3
COM3
COM3
COM3
COM3
COM0
I6
I4
15
34
I7
I5
I2
18
16
17
15
13
14
11
12
9
10
8
7
5
6
3
4
1
2
20
37
COM1
COM1
COM2
COM2
COM1
COM1
COM2
COM2
COM1
COM1
COM1
COM1
COM1
COM3
COM2
COM2
COM2
COM2
Sinking inputs - wire Com 1 to Field Power (+) 24V dc, wire Com 0 to Field Power (-) GND
Sourcing inputs - wire Com1 to Field Power (-) GND, wire Com 0 to Field Power (+) 24V dc
Note: all Com 1 are internally connected.
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
COM1
COM1
COM3
COM3
COM1
COM1
COM3
COM3
COM1
COM1
COM1
COM1
COM1
COM3
COM3
COM3
COM3
COM3
Sourcing outputs - wire Com 0 and Com 2 to Field Power (+) 24V dc, wire Com 1 and Com 3
to Field Power (-) GND
Note: all Com 1 and Com 3 are internally connected.
Sinking outputs -wire Com 2 to Field Power (+) 24Vdc, wire Com 3 to Field Power (-) GND
Note: all Com 2 are internally connected.
1
Publication CIG-WD001B-EN-P - May 2005
13-2
1790 CompactBlock LDX I/O Modules
1790-OV16X
COM0
O1
O3
O0
19
18
16
17
37
34
O6
O4
15
35
36
O7
O5
O2
13
14
33
30
31
32
O8
O10
COM2
11
12
1790D-16BVO
9
10
8
28
29
O9
27
7
26
O12
24
25
O13
5
6
COM0
O14
O11
3
4
22
23
I1
1
2
19
18
37
20
21
COM1
COM0
COM2
COM2
COM0
COM0
COM2
COM2
COM0
COM0
COM0
COM0
COM0
COM3
COM2
COM2
COM2
COM2
I3
I0
O15
16
17
34
I6
I4
15
35
36
I7
I5
I2
13
14
33
30
31
32
11
12
I8
I10
COM2
9
10
8
28
29
I9
7
27
I12
I14
I11
5
6
26
I13
24
25
I15
3
4
22
23
1
2
20
21
COM1
COM1
COM3
COM3
COM1
COM1
COM3
COM3
COM1
COM1
COM1
COM1
COM1
COM3
COM3
COM3
COM3
COM3
Sinking outputs - wire Com 0 and Com 2 to Field Power (+) 24V dc, wire Com 1 and Com 3
to Field Power (-) GND
For inputs 0-7: Sinking inputs - wire Com 1 to Field Power (+) 24V dc, wire Com 0 to Field Power (-) GND
Sourcing inputs - wire Com 1 to Field Power (-) GND, wire Com 0 to Field Power (+) 24V dc
Note: all Com 0 and Com 2 are internally connected.
For inputs 8-15: Sinking inputs - wire Com 3 to Field Power (+) 24V dc, wire Com 2 to Field Power (-) GND
Sourcing inputs - wire Com 3 to Field Power (-) GND, wire Com 2 to Field Power (+) 24V dc
Note: All Com 1 and Com 3 are internally connected - Com 1 is used for inputs 0-7, Com 3 is used for
inputs 8-15.
1790D-4RO
+24V
+24V
NC
+24V
19
18
37
16
17
35
36
GND
15
34
37
36
35
28
COM
COM
8
27
7
26
24
25
COM
COM
COM
5
6
22
23
NC
+24V
1
19
2
18
NC
NC
16
17
36
GND
COM
COM
NC
+24V
37
20
21
COM
COM
COM
3
4
+24V
NC
35
34
GND
GND
COM
15
CH1_B
CH0_B
CH1_A
NC
CH0_A
13
14
33
32
NC
NC
11
12
30
31
9
10
29
NC
8
28
27
NC
NC
NC
NC
CH2_B
CH3_B
CH2_A
CH3_A
NC
7
26
24
25
1790D-8BV8V
I7
I5
I6
15
13
14
33
32
11
12
31
30
O0
COM2
9
10
29
28
O2
O1
8
27
7
26
O4
25
O5
5
6
24
COM0
O6
O3
3
4
23
22
1
2
21
20
I1
I3
I0
O7
19
18
37
16
17
36
35
I6
I4
15
34
I7
I5
I2
13
14
33
32
11
12
31
30
O0
COM2
9
10
29
28
8
27
26
NC
O6
O5
5
6
25
NC
O4
O3
7
24
1
20
NC
O2
O1
NC
2
21
NC
1790D-8BV8B
I4
22
NC
NC
NC
3
4
23
NC
NC
NC
5
6
Wire pins 17, 18, 19 to Field Power (+) 24Vdc
Wire pins 35, 36, 37 to Field Power (-) GND
I3
34
9
10
29
NC
CH2_B
CH3_B
CH2_A
CH3_A
NC
Wire pins 17, 18, 19 to Field Power (+) 24Vdc
Wire pins 35, 36, 37 to Field Power (-) GND
I2
16
30
COM
NC
I1
17
11
12
31
NC
I0
18
13
32
NC
COM0
CH1_B
CH0_B
CH1_A
NC
CH0_A
14
33
GND
GND
19
NC
NC
1790D-4TO
23
O7
3
4
22
1
2
21
20
COM1
COM1
COM3
COM3
COM1
COM1
COM3
COM3
COM1
COM1
COM1
COM1
COM1
COM3
COM3
COM3
COM3
COM3
COM1
COM1
COM2
COM2
COM1
COM1
COM2
COM2
COM1
COM1
COM1
COM1
COM1
COM3
COM2
COM2
COM2
COM2
Sinking inputs - wire Com 1 to Field Power (+) 24V dc, wire Com 0 to Field Power (-) GND
Sinking inputs - wire Com 1 to Field Power (+) 24V dc, wire Com 0 to Field Power (-) GND
Sourcing inputs - wire Com1 to Field Power (-) GND, wire Com 0 to Field Power (+) 24V dc
Note: all Com 1 are internally connected.
Sourcing inputs - wire Com1 to Field Power (-) GND, wire Com 0 to Field Power (+) 24V dc
Note: all Com 1 are internally connected.
Sinking outputs -wire Com 2 to Field Power (+) 24Vdc, wire Com 3 to Field Power (-) GND
Note: all Com 3 are internally connected.
Sinking outputs -wire Com 2 to Field Power (+) 24Vdc, wire Com 3 to Field Power (-) GND
Note: all Com 2 are internally connected.
Publication CIG-WD001B-EN-P - May 2005
1790 CompactBlock LDX I/O Modules
1790D-NOC2
+24V
1790D-NOV2
CH1
CH0
+24V
+24V
+24V
19
18
16
15
35
36
GND
34
13
14
33
11
12
30
31
32
9
10
28
29
8
7
27
26
5
6
3
4
24
25
1
2
22
23
19
18
GND
COM
15
35
36
GND
GND
16
17
37
20
21
34
13
14
33
32
CH1
CH0
18
16
35
36
GND
15
34
13
14
33
11
12
30
31
32
CH2
9
10
28
29
+24V
CH3
8
27
7
26
5
6
24
25
3
4
22
23
1
2
COM
18
35
36
15
34
13
14
33
O1
O3
19
18
37
16
17
35
36
O6
O4
15
34
O7
O5
O2
13
14
33
30
31
32
O8
28
29
3
4
22
23
1
2
20
21
CH2
CH3
9
10
28
29
8
27
7
26
5
6
24
25
3
4
22
23
1
2
20
21
GND
COM
COM
COM
COM
Wire pins 17, 18 and 19 to Field Power (+) 24Vdc
Wire pins 35, 36 and 37 to Field Power (-) GND
O10
O9
9
10
24
1790D-OV16
COM2
11
12
11
30
1790D-OB16
O0
CH1
12
31
32
GND
COM
COM
16
17
37
Wire pins 17, 18 and 19 to Field Power (+) 24Vdc
Wire pins 35, 36 and 37 to Field Power (-) GND
COM0
5
6
25
COM
CH0
GND
COM
7
26
+24V
19
20
21
GND
GND
27
1790D-N4VO
+24V
17
37
8
28
Wire pins 17, 18 and 19 to Field Power (+) 24Vdc
Wire pins 35, 36 and 37 to Field Power (-) GND
+24V
19
9
10
29
COM
1790D-N4CO
+24V
30
GND
COM
11
12
31
GND
Wire pins 17, 18 and 19 to Field Power (+) 24Vdc
Wire pins 35, 36 and 37 to Field Power (-) GND
+24V
CH1
CH0
+24V
+24V
17
37
13-3
8
27
7
26
O12
O11
5
6
24
25
22
O1
1
2
19
18
20
21
O3
O0
O15
3
4
23
COM0
O14
O13
16
17
37
35
36
13
14
33
COM2
11
12
30
31
32
O8
O6
O4
15
34
O7
O5
O2
9
10
28
29
O10
O12
O9
8
27
O11
7
26
5
6
24
25
O14
O13
22
23
O15
3
4
1
2
20
21
COM1
COM1
COM3
COM3
COM1
COM1
COM3
COM3
COM1
COM1
COM1
COM1
COM1
COM3
COM3
COM3
COM3
COM3
COM1
COM0
COM2
COM2
COM0
COM0
COM2
COM2
COM0
COM0
COM0
COM0
COM0
COM3
COM2
COM2
COM2
COM2
Sourcing outputs - wire Com 0 and Com 2 to Field Power (+) 24V dc, wire Com 1 and Com 3
to Field Power (-) GND
Sinking outputs - wire Com 0 and Com 2 to Field Power (+) 24V dc, wire Com 1 and Com 3
to Field Power (-) GND
Note: all Com 1 and Com 3 are internally connected.
Note: all Com 0 and Com 2 are internally connected.
1790D-OW6
+24V
CH0
+24V
CH1
COM0
19
18
37
16
17
36
35
15
34
13
14
33
CH3
CH2
COM2
COM1
32
11
12
31
30
COM3
29
CH4
CH5
NC
NC
COM4
COM5
NC
NC
9
10
28
1790D-OW8X
8
27
7
26
5
6
25
24
GND
3
4
23
22
1
2
21
20
+24V
CH0
+24V
CH1
COM0
19
18
37
16
17
36
35
15
34
13
14
33
CH3
CH2
COM2
COM1
32
11
12
31
30
COM3
9
10
29
CH4
CH5
CH6
CH7
COM4
COM5
COM6
COM7
28
8
27
7
26
5
6
25
24
3
4
23
22
1
2
21
20
GND
GND
GND
Wire pins 18 and 19 to Field Power (+) 24Vdc
Wire pins 36 and 37 to Field Power (-) GND
Wire pins 18 and 19 to Field Power (+) 24Vdc
Wire pins 36 and 37 to Field Power (-) GND
Publication CIG-WD001B-EN-P - May 2005
13-4
1790 CompactBlock LDX I/O Modules
1790-T16BVOX
IN0
IN4
IN2
2
6
1
IN8
COM0
IN10
COM1
IN6
4
8
3
IN1
7
11
18
17
IN9
VAC
For inputs 0-7 - Sinking inputs - wire Com 0 and Com 1 to Field Power (-) GND
Sourcing inputs - wire Com 0 and Com 1 to Field Power (+) 24V dc
For inputs 8-15 - Sinking inputs - wire Com 2 and Com 3 to Field Power (-) GND
Sourcing inputs - wire Com 2 and Com 3 to Field Power (+) 24V dc
5
2
19
4
IN4
8
COM
1
IN6
3
2
5
4
7
6
IN1
11
9
8
IN3
IN7
17
COM
1
18
4
8
IN3
0UT0
1
3
2
5
4
COM
7
6
8
COM
COM
11
10
12
COM
14
16
COM
COM
1
19
18
20
COM
COM
COM
Wire 120 V ac Field Power to VAC (pin 1) and COM (pin 2)
NOTE: All VAC are internally connected. All COM are internally connected.
Publication CIG-WD001B-EN-P - May 2005
OUT4
OUT2
OUT7
17
15
13
COM
18
16
OUT3
GND
20
OUT5
OUT7
Sinking inputs - wire COM (pin 9) to Field Power (-) GND
Sourcing inputs - wire COM (pin 9) to Field Power (+) 24V dc
Note: both COM (pins 9 and 10) are internally connected.
Sinking outputs -wire VDC (pin 11) to Field Power (+) 24Vdc,
wire GND (pin 12) to Field Power (-) GND
OUT0
OUT6
0UT5
0UT3
9
19
1790-TOB16X
0UT4
0UT2
0UT1
14
OUT6
17
15
OUT1
COM
IN7
OUT4
13
12
10
IN5
OUT7
11
9
1790-TOA8X
VAC
COM
OUT2
VDC
7
6
IN1
OUT0
COM
5
2
20
Sinking inputs - wire COM (pin 9) to Field Power (-) GND
Sourcing inputs - wire COM (pin 9) to Field Power (+) 24Vdc
Note: both COM (pins 9 and 10) are internally connected.
Sourcing outputs -wire VDC (pin 11) to Field Power (+) 24Vdc,
wire GND (pin 12) to Field Power (-) GND
VAC
20
COM
COM
COM
IN6
3
OUT5
OUT3
GND
IN4
IN2
19
16
14
OUT1
COM
IN0
OUT6
15
13
12
10
IN5
18
16
14
COM
COM
19
Wire 120Vac Field Power across VAC (pin 1) and COM (pin 2)
Note: all VAC are internally connected. All COM are internally connected.
OUT4
OUT2
VDC
12
10
COM
IN7
17
15
13
1790-T8BV8VX
OUT0
COM
IN2
11
9
6
COM
IN6
IN5
IN3
7
1790-T8BV8BX
IN0
IN4
IN2
IN1
3
IN13
IN15
IN11
IN0
VAC
1
20
15
13
COM0
COM1
IN7
IN12
IN14
16
14
9
IN5
IN3
12
10
5
1790-T8A0X
3
2
VDC0
OUT6
5
4
7
6
VDC1
11
9
8
OUT8
OUT12
OUT10
OUT14
10
12
17
15
13
14
16
19
18
20
OUT1
OUT5
OUT9
GND0
OUT13
OUT3
OUT7
OUT11
GND1
OUT15
Sourcing outputs - wire VDC0 (pin 9) and VDC1 (pin 11) to Field Power (+)
24V dc, wire GND0 (pin 10) and GND1 (pin 12) to Field Power (-) GND
1790 CompactBlock LDX I/O Modules
1790-TOV16X
OUT0
OUT4
OUT2
1
VDC0
OUT6
3
5
2
7
4
8
OUT5
OUT3
1790-TOW8X
17
15
13
12
10
VDC
OUT8
OUT12
OUT10
OUT14
11
9
6
OUT1
VDC1
1
19
18
16
14
OUT1
OUT0
3
5
2
20
OUT9
GND0
OUT13
OUT7
OUT11
GND1
OUT15
4
GND
7
6
0UT0
8
1
3
5
2
4
6
COM
8
COM
19
1
NC
VDC0
OUT6
3
20
NC
COM
COM
OUT4
OUT2
Wire 120Vac Field Power to VAC (pin 1) and COM (pin 2)
Note: all VAC are internally connected. All COM are internally connected.
5
2
VDC1
7
4
6
OUT4
OUT2
1
3
2
VDC0
OUT6
5
4
OUT1
7
6
OUT5
OUT3
VDC1
8
8
10
17
15
13
12
12
10
17
15
13
16
14
19
18
20
OUT1
OUT5
OUT9
GND0
OUT13
OUT3
OUT7
OUT11
GND1
OUT15
Sourcing outputs - wire VDC0 (pin 9) and VDC1 (pin 11) to Field Power (+)
24V dc, wire GND0 (pin 10) and GND1 (pin 12) to Field Power (-) GND
1790D-TOW6
OUT8
OUT12
OUT10
OUT14
11
9
OUT8
OUT12
OUT10
OUT14
11
9
1790D-TOV16
OUT0
20
COM1
COM5
COM3
COM7
COM0
COM2
COM6
COM4
NC
OUT0
18
16
14
COM
COM
18
16
14
19
Wire VDC (pin 1) to Field Power (+) 24V dc
Wire GND (pin 2) to Field Power (-) GND
NC
17
15
13
12
10
COM
COM
11
9
NC
0UT5
0UT3
7
12
10
NC
17
15
13
1790D-TOB16
0UT4
0UT2
0UT1
11
9
OUT7
OUT6
OUT4
1790D-TOA6
VAC
OUT5
OUT3
OUT2
Sinking outputs - wire VDC0 (pin 9) and VDC1 (pin 11) to Field Power (+) 24V
dc, wire GND0 (pin 10) and GND1 (pin 12) to Field Power (-) GND
VAC
13-5
14
16
OUT0
NC
1
19
18
VDC
20
OUT9
GND0
OUT13
OUT7
OUT11
GND1
OUT15
Sinking outputs - wire VDC0 (pin 9) and VDC1 (pin 11) to Field Power (+) 24V
dc, wire GND0 (pin 10) and GND1 (pin 12) to Field Power (-) GND
3
2
GND
5
4
OUT4
OUT2
OUT1
7
6
11
9
8
10
NC
OUT5
OUT3
12
14
NC
17
15
13
16
19
18
20
COM0
COM4
COM2
NC
NC
COM1
COM5
COM3
NC
Wire VDC (pin 1) to Field Power (+) 24V dc
Wire GND (pin 2) to Field Power (-) GND
Publication CIG-WD001B-EN-P - May 2005
13-6
1790 CompactBlock LDX I/O Modules
1790D-T16BVO
IN0
IN4
IN2
2
6
1
IN8
COM0
IN10
COM1
IN6
4
8
3
12
10
5
IN1
7
18
+24V
17
3
5
2
7
4
11
9
6
8
NC
NC
17
15
13
19
18
20
GND
CH1_B
COM
CH2_B
NC
CH0_B
COM
NC
CH3_B
NC
19
IN13
IN15
IN11
CH1_A
COM
CH2_A
CH0_A
COM
NC
CH3_A
1
20
15
13
IN9
COM0
COM1
IN7
IN12
IN14
16
14
11
9
IN5
IN3
1790D-T4RO
12
10
16
14
Wire pin 1 to Field Power (+) 24Vdc
Wire pin 2 to Field Power (-) GND
For inputs 0-7 - Sinking inputs - wire COM 0 (pin 9) to Field Power (-) GND
Sourcing inputs - wire COM 0 (pin 9) to Field Power (+) 24V dc
For inputs 8-15 - Sinking inputs - wire COM 1 (pin 11) to Field Power (-) GND
Sourcing inputs - wire COM 1 (pin 11) to Field Power (+) 24V dc
Note: Both COM 0 are internally connected - COM 0 is used for inputs 0-7,
COM 1 is used for input 8-15. Both COM 1 are internally connected.
1790D-T4TO
+24V
1790D-T8AO
CH1_A
NC
CH2_A
CH0_A
NC
CH3_A
1
3
2
5
7
4
GND
11
9
6
8
17
VAC
19
1
18
16
14
CH1_B
NC
CH2_B
CH0_B
NC
CH3_B
IN0
NC
15
13
12
10
VAC
NC
NC
5
2
NC
NC
3
20
8
IN4
1
IN6
3
2
5
4
IN1
7
6
8
IN5
IN3
11
9
10
12
IN7
IN0
OUT4
14
16
OUT1
GND
1
19
18
20
OUT3
3
2
5
4
OUT7
COM
Sourcing outputs -wire VDC (pin 11) to Field Power (+) 24Vdc,
wire GND (pin 12) to Field Power (-) GND
7
6
11
9
8
10
12
14
OUT6
17
15
13
16
OUT1
COM
IN7
OUT4
OUT2
VDC
IN5
IN3
OUT0
COM
IN6
IN1
OUT5
Sinking inputs - wire COM (pin 9) to Field Power (-) GND
Sourcing inputs - wire COM (pin 9) to Field Power (+) 24Vdc
Note: both COM (pins 9 and 10) are internally connected.
Publication CIG-WD001B-EN-P - May 2005
IN4
IN2
OUT6
17
15
13
COM
COM
COM
COM
Wire 120Vac Field Power across VAC (pin 1) and COM (pin 2)
Note: all VAC are internally connected. All COM are internally connected.
OUT2
VDC
COM
20
1790D-T8BV8V
OUT0
COM
IN2
19
18
16
14
COM
COM
1790D-T8BV8B
IN0
IN7
17
15
13
12
10
COM
COM
Wire pin 1 to Field Power (+) 24V dc
Wire pin 2 to Field Power (-) GND
11
9
6
IN6
IN5
IN3
7
4
COM
NC
IN4
IN2
IN1
GND
19
18
20
OUT5
OUT3
OUT7
Sinking inputs - wire COM (pin 9) to Field Power (-) GND
Sourcing inputs - wire COM (pin 9) to Field Power (+) 24V dc
Note: both COM (pins 9 and 10) are internally connected.
Sinking outputs -wire VDC (pin 11) to Field Power (+) 24Vdc,
wire GND (pin 12) to Field Power (-) GND
1790 CompactBlock LDX I/O Modules
1790D-TNOC2
+24V
CH1
1
NC
3
5
2
GND
11
9
6
8
12
17
18
NC
NC
1
19
16
14
NC
NC
5
4
GND
7
CH1
10
COM1
COM0
NC
NC
1
3
5
2
4
GND
11
9
6
8
+24V
NC
12
14
NC
CH1
CH0
NC
17
15
13
COM1
COM3
COM0
COM2
NC
10
1
19
18
16
3
OUT0
2
20
GND
NC
NC
NC
1
3
5
2
4
GND
11
9
6
8
+24V
NC
NC
17
15
13
12
10
18
16
14
1
19
7
4
3
2
GND
5
4
7
6
11
9
8
10
8
12
14
NC
10
NC
17
15
13
19
18
16
20
NC
NC
NC
3
2
5
4
7
6
11
9
8
NC
NC
17
15
13
19
18
20
NC
12
10
16
14
Wire pin 1 to Field Power (+) 24V dc
Wire pin 2 to Field Power (-) GND
1790P-T8BV8B
IN0
NC
NC
14
CH1_B
NC
CH2_B
CH0_B
NC
CH3_B
IN4
17
16
19
18
1
20
NC
NC
Wire pin 1 to Field Power (+) 24V dc
Wire pin 2 to Field Power (-) GND
NC
IN6
3
2
5
4
IN1
7
6
11
9
8
10
12
14
OUT6
17
15
13
16
OUT1
COM
IN7
OUT4
OUT2
VDC
IN5
IN3
OUT0
COM
IN2
NC
15
13
12
11
9
6
NC
NC
COM1
COM3
COM0
COM2
NC
1790P-T4T0
1
NC
GND
CH1_B
COM
CH2_B
NC
CH0_B
COM
NC
CH3_B
20
COM0
COM4
COM2
NC
NC
COM1
COM5
COM3
NC
CH1_A
NC
CH2_A
CH0_A
NC
CH3_A
NC
NC
CH1_A
COM
CH2_A
CH0_A
COM
NC
CH3_A
Wire VDC (pin 1) to Field Power (+) 24V dc
Wire GND (pin 2) to Field Power (-) GND
+24V
NC
1790P-T4R0
OUT5
OUT3
7
20
NC
Wire pin 1 to Field Power (+) 24Vdc
Wire pin 2 to Field Power (-) GND
OUT4
OUT2
OUT1
NC
CH3
5
1790P-T0W6
NC
19
18
16
14
NC
CH2
Wire pin 1 to Field Power (+) 24Vdc
Wire pin 2 to Field Power (-) GND
VDC
12
Wire pin 1 to Field Power (+) 24Vdc
Wire pin 2 to Field Power (-) GND
NC
NC
7
NC
17
15
13
1790D-TN4VO
NC
CH3
CH2
11
9
6
1790D-TN4CO
CH0
NC
NC
NC
8
Wire pin 1 to Field Power (+) 24Vdc
Wire pin 2 to Field Power (-) GND
+24V
NC
NC
NC
3
2
20
NC
NC
CH1
CH0
NC
15
13
10
COM1
COM0
NC
+24V
NC
NC
NC
7
4
1790D-TNOV2
NC
NC
CH0
13-7
GND
19
18
20
OUT5
OUT3
OUT7
Sinking inputs - Wire COM (pin 9) to Field Power (-) GND
Sourcing inputs - Wire COM (pin 9) to Field Power (+) 24V dc
Note: Both COM (pins 9 and 10) are internally connected.
Sourcing outputs - Wire VDC (pin 11) to Field Power (+) 24V dc, and
wire GND (pin 12) to Field Power (-) GND
Publication CIG-WD001B-EN-P - May 2005
13-8
1790 CompactBlock LDX I/O Modules
1790P-T8BV8V
IN0
IN4
1
IN6
3
2
5
4
IN1
7
6
11
9
8
10
12
14
16
OUT1
GND
+24V
CH1
CH0
OUT6
17
15
13
COM
IN7
OUT4
OUT2
VDC
IN5
IN3
OUT0
COM
IN2
1790P-TN0C2
1
19
18
3
2
20
GND
OUT5
OUT3
OUT7
COM1
COM0
NC
NC
CH1
CH0
5
4
NC
CH3
CH2
3
GND
7
6
11
9
8
NC
NC
NC
12
14
COM1
COM3
COM0
COM2
NC
NC
10
NC
17
15
13
16
19
18
20
NC
NC
Wire pin 1 to Field Power (+) 24V dc
Wire pin 2 to Field Power (-) GND
Publication CIG-WD001B-EN-P - May 2005
12
NC
17
15
13
14
16
NC
NC
NC
19
18
20
NC
NC
Wire pin 1 to Field Power (+) 24V dc
Wire pin 2 to Field Power (-) GND
1790P-TN4C0
2
6
11
9
10
Sourcing outputs - Wire VDC (pin 11) to Field Power (+) 24V dc, and
wire GND (pin 12) to Field Power (-) GND
1
7
NC
NC
NC
8
Sinking inputs - Wire COM (pin 9) to Field Power (-) GND
Sourcing inputs - Wire COM (pin 9) to Field Power (+) 24V dc
Note: Both COM (pins 9 and 10) are internally connected.
+24V
5
4
NC
NC
NC
NC
Chapter
14
1791 I/O Blocks
1791-16ACB
120V ac
Gnd
n.c.
Blu
RIO
Clr
L2/N
Com 1
Com 1
Com 1
In 00
In 01
In 02
In 03
In 04
In 05
In 06
1791-16AOB
24V dc
120V ac
L1
N
Gnd
n.c.
Shd
n.c.
Blu
RIO
Com 2
Clr
L2/N
Com 2
Com 2
L2/N
Com 1
In 10
Com 1
Com 1
In 11
In 00
In 12
In 13
In 01
In 14
In 02
In 03
In 15
In 04
In 16
In 17
In 05
In 06
In 07
Com 1 terminals are connected internally.
Com 2 terminals are connected internally.
L1
Gnd
N
n.c.
Blu
n.c.
Shd
RIO
Com 2
In 10
In 00
In 11
In 01
In 12
In 13
In 02
In 03
In 14
+
Ret 1
Ret 1
In 00
In 01
In 02
In 03
+
In 04
In 05
In 06
n.c.
Shd
n.c.
n.c.
Ret 3
In 10
Out 01
In 12
In 13
In 14
In 15
In 16
In 17
Vdc 3
Vdc 3
Out 00
In 11
In 07
Ret 1 terminals are connected internally.
Ret 2 terminals are connected internally.
1
n.c.
n.c.
Ret 2
Ret 2
+
In 12
In 13
In 16
In 17
+
In 14
In 15
In 05
In 06
Out 02
Out 03
Out 04
Out 05
Out 06
n.c.
In 16
In 17
In 07
Ret 1 terminals are connected internally.
Ret 2 terminals are connected internally.
Gnd
n.c.
n.c.
n.c.
n.c.
Blu
RIO
Clr
Ret 4
Vdc 4
Vdc 4
+
n.c.
In 11
120V ac
n.c.
+
Clr
In 10
1791-24A8B
+
RIO
Ret 2
Ret 2
In 04
In 15
In 07
Com 1 terminals are connected internally.
Com 2 terminals are connected internally.
+24
Ret +24
n.c.
Ret 1
Ret 1
24V dc
n.c.
Blu
n.c.
Shd
n.c.
1791-16BCB
Gnd
Ret +24
Clr
L2/N
Com 2
Com 2
+24
+
1791-16AOB
Out 10
Out 11
Out 12
Out 13
Out 14
Out 15
Out 16
Out 17
Out 07
Vdc 3 terminals are connected internally.
Vdc 4 terminals are connected internally.
Each output must be fused externally.
L2/N
Com 1
Com 1
Com 1
In 00
In 01
In 02
In 03
In 04
In 05
In 06
L1
n.c.
N
n.c.
n.c.
n.c.
Shd
Com 2
Com 2
Com 2
n.c.
L2/N
In 10
Com 3
Com 3
Com 3
In 00
In 11
In 01
In 12
In 13
In 02
In 03
In 14
In 04
In 15
In 16
In 17
L2/N
In 05
In 06
In 07
Com 1 terminals are connected internally.
Com 2 terminals are connected internally.
n.c.
n.c.
n.c.
n.c.
L1 4
L1 4
L1 4
L1
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
Out 07
In 07
L1 3 terminals are connected internally.
L1 4 terminals are connected internally.
Each output must be fused externally.
Publication CIG-WD001B-EN-P - May 2005
1791 I/O Blocks
1791-24ARB
1791-24B8B
120V ac, Relay
Gnd
RIO
Clr
Com 1
L2/N
Com 1
Com 1
In 00
In 01
In 02
In 03
In 04
In 05
In 06
N
n.c.
n.c.
n.c.
Com 2
L2/N
Com 2
Com 2
Vac/dc 4
Com 3
L2/N
Vac/dc 4
Com 3
Com 3
In 10
In 12
In 13
In 05
In 06
In 16
In 17
In 07
Com 1 terminals are connected internally.
Com 2 terminals are connected internally.
In 01
In 02
In 03
+
In 14
In 04
+
In 15
In 05
In 06
In 07
L1 3 terminals are connected internally.
Vac/dc 4 terminals are connected internally.
Each output must be fused externally.
In 00
In 12
In 13
In 02
In 03
Out 06
Out 07
Ret 3
Ret 3
In 11
In 01
+
n.c.
In 10
In 00
Out 05
n.c.
Ret 2
Ret 2
Ret 1
Ret 1
Out 04
n.c.
n.c.
n.c.
n.c.
Out 02
Out 03
In 04
In 15
L1/+
n.c.
n.c.
Shd
Clr
Out 01
In 02
In 03
In 14
RIO
Out 00
In 01
Ret +24
n.c.
Blu
Vac/dc 4
In 00
In 11
+24
Gnd
n.c.
n.c.
n.c.
n.c.
Shd
24V dc
n.c.
n.c.
+
n.c.
Blu
L1
In 05
In 06
In 16
In 17
In 07
Ret 1 terminals are connected internally.
Ret 2 terminals are connected internally.
1791-24BRB
In 04
RIO
Clr
n.c.
Ret 1
Ret 1
In 00
In 01
In 02
In 03
+
In 04
In 05
In 06
n.c.
+
n.c.
Blu
n.c.
n.c.
n.c.
Shd
n.c.
n.c.
n.c.
Ret 2
Ret 2
Ret 3
Ret 3
In 10
In 00
In 11
In 01
In 12
In 13
In 02
In 03
+
In 14
+
In 15
In 04
In 05
In 06
In 16
In 17
In 07
Ret 1 terminals are connected internally.
Ret 2 terminals are connected internally.
n.c.
n.c.
n.c.
n.c.
Vac/dc 4
L1
Gnd
n.c.
Blu
RIO
L1/+
Vac/dc 4
Out 00
Com 1
Com 1
Com 1
In 00
Out 01
In 07
L2/N/Ret 3 terminals are connected internally.
Vac/dc 4 terminals are connected internally.
Each output must be fused externally.
Clr
n.c.
Ret 1
Ret 1
In 00
In 01
In 02
In 03
+
In 04
In 05
In 06
Ret +24
In 10
In 00
In 01
In 02
In 03
In 04
In 05
In 06
In 16
In 17
In 07
Com 1 terminals are connected internally.
Com 2 terminals are connected internally.
n.c.
n.c.
n.c.
Ret 2
Ret 2
Ret 3
Ret 3
In 10
In 00
In 11
In 01
In 12
In 13
In 14
In 15
In 16
In 17
In 07
Ret 1 terminals are connected internally.
Ret 2 terminals are connected internally.
Publication CIG-WD001B-EN-P - May 2005
Vdc 4
Vdc 4
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
Out 07
+
In 02
In 03
+
In 04
In 05
In 06
n.c.
n.c.
Gnd
n.c.
n.c.
n.c.
Blu
RIO
n.c.
Ret 4
Ret 4
Clr
L2/N
Com in
Com in
In 10
Com in
In 11
In 00
In 12
In 13
In 01
In 02
In 14
+
In 03
In 15
In 04
In 16
In 17
In 05
In 06
In 07
Ret 3 terminals are connected internally.
Ret 4 terminals are connected internally.
n.c.
n.c.
n.c.
Shd
Com 4
Com 4
Com 4
L2/N
In 10
In 11
In 12
In 13
In 14
In 15
In 16
In 17
In 07
Com 3 terminals are connected internally.
Com 4 terminals are connected internally.
120V ac
n.c.
n.c.
n.c.
Shd
Com 3
Com 3
1791-8ACB
n.c.
+
RIO
+24
Com 3
L2/N
In 15
In 05
In 06
Out 06
Out 07
L2/N
In 14
In 04
Out 05
Com 2
Com 2
In 12
In 13
In 02
In 03
Out 04
Com 2
n.c.
In 11
In 01
Out 02
Out 03
n.c.
n.c.
n.c.
Shd
Clr
L2/N
n.c.
N
24V dc
n.c.
Blu
Ret 4
120V ac
n.c.
1791-32BOB
Gnd
n.c.
n.c.
1791-32AOB
+24
Ret +24
n.c.
In 07
Ret 3 terminals are connected internally.
Vdc 4 terminals are connected internally.
Each output must be fused externally.
24V dc, Relay
Gnd
n.c.
+
14-2
L1
N
n.c.
Shd
L1 out
L1 out
L1 out
L1
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
Out 07
In 07
Com in terminals are connected internally.
L1 out terminals are connected internally.
Each output must be fused externally.
1791 I/O Blocks
1791-8BCB
n.c.
Shd
Com in
Com in
Com in
In 00
RIO
Vac/dc out
Clr
n.c.
L1/+
Vac/dc out
Ret In
Ret In
Vac/dc out
Out 00
In 00
Out 01
In 01
In 02
In 01
Out 02
Out 03
In 03
In 02
In 03
Out 04
In 04
+
Out 05
In 05
In 06
In 04
In 05
In 06
Out 06
Out 07
Gnd
Ret +24
n.c.
Shd
RIO
Out 00
Out 02
Out 03
Out 04
+
Out 05
Gnd
+
Out 02
Out 03
Out 04
In 04
Out 05
In 05
In 06
Out 06
Out 07
L1/+
Out 01
In 02
In 03
Out 06
Out 07
In 07
Ret In terminals are connected internally.
Vac/dc Out terminals are connected internally.
Each output must be fused externally.
1791-IOVW
Vdc A
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
Vdc B
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
n.c.
24V dc
Neut
24V dc
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm A
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm B
Vdc A
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
Vdc B
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
n.c.
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
+24V dc
Clr
Shield
Blu
Gnd
24V dc
Neut
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm A
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm B
+24V dc
+
+
RIO
Vdc A
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
Vdc B
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
n.c.
+
+
Blu
Out 00
In 01
+
+
+
RIO
Shield
+
Clr
Vac/dc Out
In 00
Out 01
24V dc
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
Vac/dc Out
Ret In
Ret In
1791-IOBW
Comm A
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
Comm B
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
n.c.
n.c.
n.c.
In 07
Ret In terminals are connected internally.
Vdc Out terminals are connected internally.
Each output must be fused externally.
In 07
Com in terminals are connected internally.
L1 out terminals are connected internally.
Each output must be fused externally.
n.c.
Shd
Clr
Ret Out
Vdc Out
Vdc Out
Ret +24
n.c.
Blu
+
Clr
L2/N
n.c.
Blu
+24
+
RIO
Gnd
N
24V dc, Relay
+
Gnd
+24
+
24V dc
120V ac, Relay
L1
n.c.
Blu
1791-8BRB
L2/N/-
1791-8ARB
14-3
Publication CIG-WD001B-EN-P - May 2005
1791 I/O Blocks
1791-IOBX
1791-IOVX
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
Vdc A
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
Vdc B
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
n.c.
24V dc
Neut
+24V dc
Clr
Blu
Gnd
Vdc A
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
Vdc B
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
n.c.
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm A
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm B
24V dc
Neut
+24V dc
+
RIO
Shield
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm A
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm B
+
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm A
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm B
Vdc A
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
Vdc B
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
n.c.
+
Vdc A
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
Vdc B
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
n.c.
+
Publication CIG-WD001B-EN-P - May 2005
Vdc A
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
Vdc B
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
n.c.
+
+
RIO
Gnd
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
+
+
Blu
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm A
Out 00
Out 02
Out 04
Out 06
Out 10
Out 12
Out 14
Out 16
Comm B
+
+
Shield
Vdc A
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
Vdc B
Out 01
Out 03
Out 05
Out 07
Out 11
Out 13
Out 15
Out 17
n.c.
+
+
Comm A
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
Comm B
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
n.c.
Clr
+
+
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
+
Comm A
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
Comm B
In 01
In 03
In 05
In 07
In 11
In 13
In 15
In 17
n.c.
+
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
In 00
In 02
In 04
In 06
In 10
In 12
In 14
In 16
n.c.
24V dc
+
24V dc
+
14-4
1791 I/O Blocks
1791-N4C2 – Current applications
Gnd
RIO
n.c.
Blu
Clr
L1
n.c.
Shd
n.c.
Blu
RIO
Clr
In V 0
Ret In 0
Ret In 0
In I 0
In V 1
Gnd In 0
Ret In 1
In I 1
Gnd In 1
In V 2
Ret In 2
In I 2
In V 3
Gnd In 2
Ret In 3
In I 3
Gnd In 3
+24V dc
Rt Out 0
Rt Out 1
Rt Out 0
Rt Out 1
Out 0
Out 1
n.c.
1791-N4C2 – Voltage applications
Gnd
N
L1
Gnd
N
n.c.
Shd
RIO
In V 0
RIO
n.c.
Blu
Clr
Ret In 0
Gnd In 0
Ret In 1
Gnd In 1
Ret In 2
Gnd In 2
Ret In 3
Gnd In 3
Rt Out 0
Rt Out 1
n.c.
n.c.
Shd
Clr
In V 0
Ret In 0
In I 0
In V 1
In I 1
In V 2
In I 2
In V 3
In I 3
+24V dc
Out 0
Out 1
Connected this way, external input loop
power is needed.
Rt Out 0
Rt Out 1
n.c.
In I 0
In V 1
In I 1
In V 2
In I 2
In V 3
Gnd In 2
Ret In 3
In I 3
Gnd In 3
+24V dc
Rt Out 0
Rt Out 1
Out 0
Out 1
n.c.
External input loop power needed.
1791-N4V2 – Voltage applications
n.c.
Blu
RIO
In V 0
Ret In 2
Out 0
Out 1
Gnd
N
n.c.
Shd
Gnd In 1
Input loop power provided internally.
L1
Clr
N
Gnd In 0
Ret In 1
1791-N4V2 – Current applications
Gnd
n.c.
Blu
L1
Ret In 0
In I 0
Gnd In 0
In V 1
Ret In 1
In I 1
Gnd In 1
In V 2
Ret In 2
In I 2
Gnd In 2
In V 3
Ret In 3
In I 3
Gnd In 3
+24V dc
n.c.
Connected this way, external input loop
power is needed.
14-5
L1
Gnd
N
n.c.
Shd
In V 0
In I 0
Gnd In 0
In V 1
Ret In 1
In I 1
Gnd In 1
In V 2
Ret In 2
In I 2
Gnd In 2
In V 3
Ret In 3
In I 3
Gnd In 3
+24V dc
Out 0
Out 1
Input loop power provided internally.
RIO
n.c.
Blu
Clr
Ret In 0
Gnd In 0
Ret In 1
Gnd In 1
Ret In 2
Gnd In 2
Ret In 3
Gnd In 3
Rt Out 0
Rt Out 1
n.c.
L1
N
n.c.
Shd
In V 0
In I 0
In V 1
In I 1
In V 2
In I 2
In V 3
In I 3
+24V dc
Out 0
Out 1
External input loop power needed.
Publication CIG-WD001B-EN-P - May 2005
1791 I/O Blocks
Gnd
RIO
n.c.
Blu
Clr
Gnd
Ret +24
n.c.
Shd
n.c.
Blu
RIO
Clr
In V 0
Ret In 0
Ret In 0
In I 0
In V 1
Gnd In 0
Ret In 1
In I 1
Gnd In 1
In V 2
Ret In 2
In I 2
In V 3
Gnd In 2
Ret In 3
In I 3
Gnd In 3
+24V dc
Rt Out 0
Rt Out 1
Rt Out 0
Rt Out 1
Out 0
Out 1
n.c.
Gnd
Ret +24
n.c.
Shd
RIO
In V 0
RIO
n.c.
Blu
Clr
Ret In 0
Gnd In 0
Ret In 1
Gnd In 1
Ret In 2
Gnd In 2
Ret In 3
Gnd In 3
Rt Out 0
Rt Out 1
n.c.
n.c.
Blu
RIO
Clr
In V 0
Ret In 0
In I 0
In V 1
In I 1
In V 2
In I 2
In V 3
In I 3
+24V dc
Out 0
Out 1
Connected this way, external input loop
power is needed.
Publication CIG-WD001B-EN-P - May 2005
Rt Out 0
Rt Out 1
n.c.
+
In I 0
In V 1
In I 1
In V 2
In I 2
In V 3
Gnd In 2
Ret In 3
In I 3
Gnd In 3
+24V dc
Rt Out 0
Rt Out 1
Out 0
Out 1
n.c.
External input loop power needed.
+24
+
1791-NDV – Voltage applications
Gnd
n.c.
Shd
In V 0
Ret In 2
Input loop power provided internally.
Ret +24
n.c.
Shd
Gnd In 1
Out 0
Out 1
+
+24
Clr
Ret +24
Gnd In 0
Ret In 1
1791-NDV – Current applications
Gnd
n.c.
Blu
+24
Ret In 0
In I 0
Gnd In 0
In V 1
Ret In 1
In I 1
Gnd In 1
In V 2
Ret In 2
In I 2
Gnd In 2
In V 3
Ret In 3
In I 3
Gnd In 3
+24V dc
n.c.
Connected this way, external input loop
power is needed.
+24
+
+24
1791-NDC – Voltage applications
+
1791-NDC – Current applications
Gnd
Ret +24
n.c.
Shd
In V 0
In I 0
Gnd In 0
In V 1
Ret In 1
In I 1
Gnd In 1
In V 2
Ret In 2
In I 2
Gnd In 2
In V 3
Ret In 3
In I 3
Gnd In 3
+24V dc
Out 0
Out 1
Input loop power provided internally.
RIO
n.c.
Blu
Clr
Ret In 0
Gnd In 0
Ret In 1
Gnd In 1
Ret In 2
Gnd In 2
Ret In 3
Gnd In 3
Rt Out 0
Rt Out 1
n.c.
+24
+
14-6
Ret +24
n.c.
Shd
In V 0
In I 0
In V 1
In I 1
In V 2
In I 2
In V 3
In I 3
+24V dc
Out 0
Out 1
External input loop power needed.
1791 I/O Blocks
1791-OA16B
1791-OA32B
120V ac
120V ac
RIO
Clr
L1 1
L1
L1 1
L1 1
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
Gnd
N
n.c.
Blu
n.c.
Shd
RIO
L1 2
L1
L1 2
L1 2
Clr
L1 1
L1
L1 1
L1 1
Out 10
Out 00
Out 11
Out 01
Out 12
Out 13
Out 02
Out 03
Out 14
Out 04
Out 15
Out 05
Out 06
Out 16
Out 17
n.c.
N
n.c.
n.c.
n.c.
Shd
n.c.
L1 2
L1
L1 2
L1 2
Out 00
Out 11
Out 01
Out 12
Out 13
Out 02
Out 03
Out 14
Out 04
Out 15
Out 05
Out 06
Out 16
Out 17
1791-OB16B
+
Vdc 1
Vdc 1
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
+
Gnd
Ret +24
n.c.
Shd
n.c.
Blu
RIO
Clr
Ret 2
Vdc 2
Vdc 2
Out 10
Out 11
Ret 1
Vdc 1
Vdc 1
Out 00
Out 01
Out 12
Out 13
Out 02
Out 03
Out 14
Out 04
Out 15
Out 16
Out 17
Out 07
Vdc 1 terminals are connected internally.
Vdc 2 terminals are connected internally.
Each output must be fused externally.
Out 05
Out 06
+24
n.c.
Ret +24
n.c.
n.c.
n.c.
Shd
n.c.
Ret 2
Vdc 2
Vdc 2
Out 10
Out 11
Out 12
Out 13
Out 14
Out 15
Out 16
Out 17
Ret 3
+
Ret 1
L1 4
L1
L1 4
L1 4
Out 10
Out 11
Out 12
Out 13
Out 14
Out 15
Out 16
Out 17
24V dc
+
Clr
+24
+
RIO
n.c.
n.c.
1791-OB32B
+
n.c.
Blu
n.c.
Out 07
L1 3 terminals are connected internally.
L1 4 terminals are connected internally.
Each output must be fused externally.
24V dc
Gnd
L1 3
L1 3
Out 10
Out 07
L1 1 terminals are connected internally.
L1 2 terminals are connected internally.
Out 07
L1 1 terminals are connected internally.
L1 2 terminals are connected internally.
Each output must be fused externally.
L1 3
L1
n.c.
Out 07
Vdc 1 terminals are connected internally.
Vdc 2 terminals are connected internally.
Vdc 3
Vdc 3
Out 00
Out 01
Out 02
Out 03
Out 04
Out 05
Out 06
n.c.
n.c.
n.c.
n.c.
Ret 4
Vdc 4
Vdc 4
+
n.c.
Blu
L1
L1
+
Gnd
14-7
Out 10
Out 11
Out 12
Out 13
Out 14
Out 15
Out 16
Out 17
Out 07
Vdc 3 terminals are connected internally.
Vdc 4 terminals are connected internally.
Each output must be fused externally.
Publication CIG-WD001B-EN-P - May 2005
14-8
1791 I/O Blocks
Notes:
Publication CIG-WD001B-EN-P - May 2005
15
Chapter
1791D CompactBlock I/O Blocks
1791D-16BO, -16BOX
VDC
IN 0
GND
IN 2
IN 1
IN 4
IN 3
VDC
IN 6
IN 5
IN 7
IN 8
GND
1791D-16VO, -16VOX
IN 10
IN 9
IN 12
IN 11
IN 14
IN 13
Not
Used
IN 0
VDC
GND
IN 15
IN 2
IN 1
IN 4
IN 6
IN 3 IN 5
VDC
IN 7
GND
1791D-4BO
GND
GND
IN 1
Not
Used
VDC
GND
Not
Used
Not
Used
VDC
IN 9
IN 12
IN 11
IN 14
IN 13
Not
Used
IN 15
-
+
IN 0
IN 10
+
-
VDC
IN 8
1791D-4B4P
IN 2
Not
Used
GND
VDC
IN 3
Not
Used
VDC
GND
VDC
Not
Used
Not
Used
IN 0
VDC
IN 1
GND
IN 2
VDC
VDC
IN 3
VDC
OUT 0 GND
GND
VDC
OUT 2 GND
OUT 1 GND
OUT 3
Not
Used
GND
+
Typical PNP 3-wire sensor
+
-
-
+
+
-
-
1791D-8B8P
VDC
IN 0
GND
-
IN 2
IN 1
IN 3
IN 4
IN 5
IN 6
VDC
IN 7
1791D-8V8P
VDC
OUT 0 OUT 2 OUT 4 OUT 6 Not
Used
GND
+
1
-
IN 0
GND
OUT 1 OUT 3 OUT 5 OUT 7
IN 1
IN 2
IN 3
IN 4
IN 5
IN 6
IN 7
OUT 0 OUT 2 OUT 4 OUT 6 Not
Used
VDC
GND
+
-
-
+
Load
+
Load
OUT 1 OUT 3 OUT 5 OUT 7
Load
Publication CIG-WD001B-EN-P - May 2005
15-2
1791D CompactBlock I/O Blocks
1791D-N4CV2X – Current
VDC
V in
0+
GND
V/I in
0V in
1+
I in
0+
V/I in
1-
V in
2+
I in
1+
V/I in
2V in
3+
I in
2+
V/I in
3-
1791D-N4CV2X – Voltage
ANLG
COM
I in
3+
V out
0+
ANAL
COM
I out
0+
V out
1+
VDC
Not
Used
I out
1+
V in
0+
GND
+
V/I in
0V in
1+
I in
0+
V/I in
1-
V in
2+
I in
1+
V in
3+
I in
2+
V/I in
3-
ANLG
COM
I in
3+
V out
0+
ANAL
COM
I out
0+
V out
1+
Not
Used
I out
1+
+
Load
Source
Load
Source
-
-
1791D-OB16P, -OB16PX
VDC
V/I in
2-
OUT 0 OUT 2
GND
OUT 4 OUT 6
VDC
OUT 1 OUT 3 OUT 5 OUT 7
1791D-OB8P
OUT 8 OUT 10 OUT 12 OUT 14
GND
VDC
Not
Used
OUT 9 OUT 11 OUT 13 OUT 15
OUT 0
GND
GND OUT 1
+
-
GND
GND OUT 3
GND
Load
+
Load
OUT 2
-
1791D-OV16P, -OV16PX
OUT 0 OUT 2
VDC
VDC
GND
OUT 1 OUT 3 OUT 5 OUT 7
-
Load
+
Publication CIG-WD001B-EN-P - May 2005
OUT 4 OUT 6
OUT 8 OUT 10 OUT 12 OUT 14
GND
Not
Used
OUT 9 OUT 11 OUT 13 OUT 15
VDC
OUT 4
GND
GND OUT 6
OUT 5 GND
GND
Not
Used
OUT 7 GND
16
Chapter
1791P CompactBlock I/O Blocks
1791P-16BO
VDC
IN 0
GND
IN 2
IN 1
IN 4
IN 3
VDC
IN 6
IN 5
IN 7
1791P-4B4P
IN 8
GND
IN 10
IN 9
IN 12
IN 11
Not
Used
IN 14
IN 13
VDC
IN 0
IN 1
GND
IN 15
-
IN 2
VDC
VDC
VDC
IN 3
VDC
GND
VDC
+
+
-
-
OUT 0 GND
OUT 2 GND
OUT 1 GND
OUT 3
Not
Used
GND
Load
+
1791P-8B8P
VDC
IN 0
GND
-
IN 2
IN 1
IN 3
IN 4
IN 5
IN 6
VDC
OUT 0 OUT 2 OUT 4 OUT 6 Not
Used
VDC
IN 7
1791P-8V8P
GND
GND
OUT 1 OUT 3 OUT 5 OUT 7
+
Load
+
IN 0
-
IN 1
IN 2
IN 4
IN 3
IN 5
IN 6
IN 7
OUT 0 OUT 2 OUT 4 OUT 6 Not
Used
VDC
GND
+
-
-
+
OUT 1 OUT 3 OUT 5 OUT 7
Load
1791P-OB16P
VDC
OUT 0 OUT 2
GND
OUT 4 OUT 6
VDC
OUT 1 OUT 3 OUT 5 OUT 7
OUT 8 OUT 10 OUT 12 OUT 14
GND
Not
Used
OUT 9 OUT 11 OUT 13 OUT 15
+
Load
-
1
Publication CIG-WD001B-EN-P - May 2005
16-2
1791P CompactBlock I/O Blocks
Notes:
Publication CIG-WD001B-EN-P - May 2005
Chapter
17
1791R CompactBlock I/O Blocks
1791R-16BO
VDC
IN 0
GND
IN 2
IN 1
IN 3
IN 4
VDC
IN 6
IN 5
IN 7
1791R-4B4P
IN 8
IN 10
GND
IN 9
IN 12
IN 11
Not
Used
IN 14
IN 13
VDC
IN 0
GND
IN 15
-
VDC
IN 1
IN 2
VDC
VDC
IN 3
VDC
VDC
+
+
-
-
OUT 0 GND
GND
OUT 2 GND
OUT 1 GND
OUT 3
Not
Used
GND
Load
+
1791R-8B8P
VDC
IN 0
GND
-
IN 2
IN 1
IN 3
IN 4
IN 5
IN 6
VDC
OUT 0 OUT 2 OUT 4 OUT 6 Not
Used
VDC
IN 7
1791R-8V8P
GND
IN 0
GND
OUT 1 OUT 3 OUT 5 OUT 7
+
IN 1
IN 2
IN 3
IN 4
IN 6
IN 5
-
GIN 7
ND
+
-
-
+
Load
+
O UT 0 OUT 2 OUT 4 OUT 6 Not
Used
VDC
OUT 1 OUT 3 OUT 5 OUT 7
Load
1791P-OB16P
VDC
OUT 0 OUT 2
GND
OUT 4 OUT 6
VDC
OUT 1 OUT 3 OUT 5 OUT 7
OUT 8 OUT 10 OUT 12 OUT 14
GND
Not
Used
OUT 9 OUT 11 OUT 13 OUT 15
+
Load
-
1
Publication CIG-WD001B-EN-P - May 2005
17-2
1791R CompactBlock I/O Blocks
Notes:
Publication CIG-WD001B-EN-P - May 2005
Chapter
18
1792D ArmorBlock MaXum I/O Blocks
1792D-12BT4PE
1792D-12BVT4D
Input M icro- Conn ector
(View into Socket)
Input Micro-Connector
(view into socket)
Pin 1 Sensor Source voltage
Pin 2 Input B
Pin 3
Pin 4
Pin 5
Pin 1 Sensor Source voltage
Pin 2 Input B
Pin 3 Return Logic Ground1
Pin 4 Input A
Pin 5 Not Used
Return Logic Ground1
Input A
Physical Earth
Outpu t Micr o-C onnect or
(View into Socket)
Output Micro-Connector
(view into socket)
Pin 1 Not Used
Pin 2 Output B
Pin 3 Auxiliary Power Ground
Pin 4 Output A
Pin 5 Physical Earth
Pin 1 Not Used
Pin 2 Output B
Pin 3 Auxiliary Power Ground
Pin 4 Output A
Pin 5 Not Used
1
Logic Ground is approximately 0.4V above DeviceNet V- measured at the module.
1
Logic Ground is approximately 0.4V above DeviceNet V- measured at the module.
1792D-16BVTOCD
Input Micro Connector
(View into Socket)
Pin 1 Sensor Source Voltage A
Pin 2 Input B
Pin 3 Return Logic Ground1
Pin 4 Input A
Pin 5 Sensor Source Voltage B
1
1
Logic Ground is approximately 0.4V above DeviceNet V-measured at the module.
1792D-16BVT0D
Input Micro Connector
(View into Socket)
Pin 1 Sensor Source Voltage
Pin 2 Input B
Pin 3 Return Logic Ground1
Pin 4 Input A
Pin 5 Not Used
1Logic Ground is approximately 0.4V above DeviceNet V-measured at the module.
Publication CIG-WD001B-EN-P - May 2005
18-2
1792D ArmorBlock MaXum I/O Blocks
1792D-2BVA2D
1792D-2BVOD
Input Micro Connector
2
1
5
3
4
1
Input Micro Connector
(View into Socket)
Pin 1 Sensor Source Voltage
Pin 2 Alarm
Pin 3 Return Logic Ground1
Pin 4 Input
Pin 5 Not Used
(View into Sockets)
Pin 1 Sensor Source Voltage
Pin 2 Not Used
Pin 3 Return Logic Ground1
Pin 4 Input
Pin 5 Not Used
(Logic Ground is approximately 0.4V above DeviceNet V-measured at the module).
1. Logic Ground is approximately 0.4V above DeviceNet V-measured at the module.
Output Micro Connector
2
1
5
4
3
(View into Socket)
Pin 1 Not used
Pin 2 Not used
Pin 3 Auxiliary Power Ground
Pin 4 Output
Pin 5 Not Used
1792D-4BV4D
1792D-4BVOD
Input Micro-Connector
(View into Socket)
Pin 1 Sensor Source voltage
Pin 2 Not Used
Pin 3 Return Logic Ground1
Pin 4 Input A
Pin 5 Not Used
2
1
5
4
Output Micro-Connector
(View into Socket)
Pin 1 Not Used
Pin 2 Not Used
Pin 3 Auxiliary Power Ground
Pin 4 Output A
Pin 5 Not Used
1.
3
Logic Ground is approximately 0.4V above DeviceNet V-measured at the module.
1
Logic Ground is approximately 0.4V
above DeviceNet V- measured at the
module.
1792D-4BVT4D
2
1
5
4
3
1
2
5
4
1
Publication CIG-WD001B-EN-P - May 2005
3
Input Micro-Connector
(View into Socket)
Pin 1 Sensor Source Voltage
Pin 2 Not Used
Pin 3 Return Logic Ground1
Pin 4 Input
Pin 5 Not Used
Input Micro-Connector
(View into Sockets)
Pin 1 Sensor Source Voltage
Pin 2 Input B
Pin 3 Return Logic Ground1
Pin 4 Input A
Pin 5 Not Used
Output Micro-Connector
(View into Sockets)
Pin 1 Not Used
Pin 2 Output B
Pin 3 Auxiliary Power Ground
Pin 4 Output A
Pin 5 Not Used
Logic Ground is approximately 0.4V above DeviceNet V-measured at the module.
1792D ArmorBlock MaXum I/O Blocks
18-3
1792D-88HC
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Module Connector
Signal
Pin Number
Signal
1
P WR1+
16
PWR 2-
2
IN _0 (GR P 1 )
17
PWR 2-
3
IN _1 (GR P 1 )
18
PWR 2-
4
IN _2 (GR P 1 )
19
PWR 2-
5
IN _3 (GR P 1 )
20
PWR 2+
6
IN _0 (GR P 2 )
21
PWR 1+
7
IN _1 (GR P 2 )
22
OU T_ 0 ( G RP 1 )
10
9
8
7
6
5
4
3
2
1
8
IN _2 (GR P 2 )
23
OU T_ 1 ( G RP 1 )
20
19
18
17
16
15
14
13
12
11
9
IN _3 (GR P 2 )
24
OU T_ 2 ( G RP 1 )
30
29
28
27
26
25
24
23
22
21
10
PWR 2+
25
OU T_ 3 ( G RP 1 )
11
PWR 1+
26
OU T_ 0 ( G RP 2 )
12
PWR 1-
27
OU T_ 1 ( G RP 2 )
13
PWR 1-
28
OU T_ 2 ( G RP 2 )
14
PWR 1-
29
OU T_ 3 ( G RP 2 )
15
PWR 1-
30
PWR 2+
Mating/Harness Connector
Connect the DeviceNet Cable to the Module
Connect the DeviceNet wiring to the 5-pin micro-connector on the
module. The micro-connector pinout is shown below.
2
3
5
1
4
Pin 1 Drain
(not connected internally)
Pin 2 V+
Pin 3 VPin 4 CAN_H
Pin 5 CAN_L
42286
Looking into connector pins
1792D-8BIO8E
1792D-8BT8PE
Input/ Output Micro-Connector
(View into Socket)
Pin 1 Sensor Source Voltage
Pin 2 Output B
Pin 3 Return Logic Ground1
Pin 4 Input A
Pin 5 Not Used
Input Micro-Connector
(view into socket)
Pin 1 Sensor Source voltage
Pin 2 Input B
Pin 3
Pin 4
Pin 5
Return Logic Ground1
Input A
PE
1Logic Ground is approximately 0.4V above DeviceNet V-measured at the module.
Output Micro-Connector
(view into socket)
Pin 1 Not Used
Pin 2 Output B
Pin 3 Auxiliary Power Ground
Pin 4 Output A
Pin 5 PE
1
Logic Ground is approximately 0.4V above DeviceNet V- measured at the module.
Publication CIG-WD001B-EN-P - May 2005
18-4
1792D ArmorBlock MaXum I/O Blocks
1792D-8BV0D
1792D-8BVT8CD
Input Micro-Connector
(View into Socket)
Pin 1 Sensor Source voltage
Pin 2 Not Used
Pin 3 Return Logic Ground1
Pin 4 Input A
Pin 5 Not Used
1
Input Micro-Connector
(View into Socket)
Pin 1 Sensor Source voltage A
Pin 2 Input B
Pin 3 Return Logic Ground1
Pin 4 Input A
Pin 5 Sensor Source voltage B
Logic Ground is approximately 0.4V above DeviceNet V- measured at the module.
Output Micro-Connector
(View into Socket)
Pin 1 Not Used
Pin 2 Output B
Pin 3 Auxiliary Power Ground
Pin 4 Output A
Pin 5 Not Used
1
Logic Ground is approximately 0.4V above DeviceNet V- measured at the module.
1792D-8BVT8D
1792D-8BVTOD
Input Micro-Connector
(View into Socket)
Pin 1 Sensor Source voltage
Pin 2 Input B
Pin 3 Return Logic Ground1
Pin 4 Input A
Pin 5 Not Used
Output Micro-Connector
(View into Socket)
Pin 1 Not Used
Pin 2 Output B
Pin 3 Auxiliary Power Ground
Pin 4 Output A
Pin 5 Not Used
1
2
1
5
4
1.
3
Input Micro-Connector
(View into Sockets)
Pin 1 Sensor Source Voltage
Pin 2 Input B
Pin 3 Return Logic Ground1
Pin 4 Input A
Pin 5 Not Used
Logic Ground is approximately 0.4V above DeviceNet V-measured at the module.
Logic Ground is approximately 0.4V above DeviceNet V- measured at the module.
1792D-OB4D
2
1
5
4
3
Micro-Connector
(View into Sockets)
Pin 1 Not Used
Pin 2 Not Used
Pin 3 Auxiliary Power Ground
Pin 4 Output
Pin 5 Not Used
Publication CIG-WD001B-EN-P - May 2005
1792D-OB8D
Output Micro-Connector
(View into Sockets)
Pin 1 Not Used
Pin 2 Not Used
Pin 3 Auxiliary Power Ground
Pin 4 Output A
Pin 5 Not Used
1792D ArmorBlock MaXum I/O Blocks
18-5
1792D-OVT16E
2
1
5
3
4
Micro-Connector
(View into Sockets)
Pin 1 Auxiliary +24V dc
Pin 2 Output B
Pin 3 Not used
Pin 4 Output A
Pin 5 Not Used
Cable Bases
1792D-CB12
1792D-CB12JP
DeviceNet Male
Connector
2
Pin 1 Drain
Pin 2 V+
Pin 3 VPin 4 CAN_H
Pin 5 CAN_L
1
5
3
Pin 1 Drain
Pin 2 V+
Pin 3 VPin 4 CAN_H
Pin 5 CAN_L
4
Auxilary Output
Male Connector
2
1
3
4
Pin 1 24Vdc
Pin 2 24Vdc
Pin 3 Return
Pin 4 Return
1792D-CB18
DeviceNet In Connector (looking
into pins)
1
5
2
4
3
1792D-CB18JP
DeviceNet Out Connector (looking
into sockets)
Pin 1 Drain
Pin 2 V+
Pin 3 VPin 4 CAN_H
Pin 5 CAN_L
1
5
2
4
3
DeviceNet Out (sockets)
DeviceNet In (pins)
Pin 1 Drain
Pin 2 V+
Pin 3 VPin 4 CAN_H
Pin 5 CAN_L
Publication CIG-WD001B-EN-P - May 2005
18-6
1792D ArmorBlock MaXum I/O Blocks
1792D-CB18P
DeviceNet Out Connector (looking
into sockets)
DeviceNet In Connector (looking
into pins)
1
5
2
4
3
Pin 1 Drain
Pin 2 V+
Pin 3 VPin 4 CAN_H
Pin 5 CAN_L
Auxiliary Output Power In Connector
(looking into pins)
1
3
2
4
1792D-CB18PT
1
5
1
2
4
4
3
3
1
1
3
4
2
2
4
DeviceNet Male
Connector
2
1
5
3
Pin 1 Drain
Pin 2 V+
Pin 3 VPin 4 CAN_H
Pin 5 CAN_L
Auxiliary Output Power In Connector
(looking into pins)
1792D-CBFM
4
Pin 1 Drain
Pin 2 V+
Pin 3 VPin 4 CAN_H
Pin 5 CAN_L
Auxilary Output
Male Connector
Publication CIG-WD001B-EN-P - May 2005
5
2
3
Auxiliary Output Power In Connector
(looking into sockets)
Pin 1 24Vdc
Pin 2 Not Used
Pin 3 Not Used
Pin 4 Return
DeviceNet Out Connector (looking
into sockets)
DeviceNet In Connector (looking
into pins)
2
1
3
4
Pin 1 24Vdc
Pin 2 24Vdc
Pin 3 Return
Pin 4 Return
1
5
2
4
3
Auxiliary Output Power In Connector
(looking into sockets)
Pin 1 24Vdc
Pin 2 Not Used
Pin 3 Not Used
Pin 4 Return
3
1
4
2
Chapter
19
1794 FLEX I/O Modules
1794-ACN15, 1794-ACN15K
1794-ACNR15, 1794-ACNR15K
Use terminal
to pass 24V
common to
next module
in series
(if necessary)
24V Common
Network
Access Port
(NAP)
ControlNet Connector
Use terminal
to pass 24V dc
power to
next module
in series
(if necessary)
24V dc
Network address switch
(Valid address range 1 to 99)
WARNING
If you connect or disconnect the ControlNet cable with power applied to
the adapter or any device on the network, an electrical arc can occur.
This could cause an explosion in hazardous location installations. Be
sure that power is removed or the area is nonhazardous before proceeding.
REDUND
24V Common
ANT MEDIA
15
ControlNet
Connector
Redundant
ControlNet
Connector
Network
Access Port
(NAP)
Network address switch
(Valid address range 1 to 99)
WARNING
24V dc
Use terminal
to pass 24V common
to next module
in series
(if necessary)
Use terminal
to pass 24V dc
power to next
module in series
(if necessary)
If you connect or disconnect the ControlNet cable with power applied to
the adapter or any device on the network, an electrical arc can occur.
This could cause an explosion in hazardous location installations. Be
sure that power is removed or the area is nonhazardous before proceeding.
1794-ADN, 1794-ADNK
ATTENTION
When connecting wiring, torque terminal
screws D, E, F and G to 7 pound-inches (0.8Nm).
Power wiring must be less than 3 meters (9.8 ft)
in length.
B
DeviceNet Connector
(connections listed below)
WARNING
Conn ect
To
BLK Wire
-V
BLU Wire
CAN Low
Bare Wire
Drain
WHT Wire
CAN High
RED Wire
+V
1
1
24V Common
1
CAN = Controller Area Network
COM
24V dc
24V
Use terminal to pass
24V common to next module
in series (if necessary)
If you connect or disconnect the DeviceNet cable
with power applied to the adapter or any device
on the network, an electrical arc can occur.
This could cause an explosion in hazardous
location installations. Be sure that power is
removed or the area is nonhazardous before
proceeding.
Use terminal to pass
24V dc power to next module
in series (if necessary)
Publication CIG-WD001B-EN-P - May 2005
19-2
1794 FLEX I/O Modules
1794-AENT
24V Common
Use terminal to pass 24V
common to next module
in series (if necessary)
WARNING
24V dc
Ethernet Connector
If you connect or disconnect the Ethernet cable with power applied to
the adapter or any device on the network, an electrical arc can occur.
This could cause an explosion in hazardous location installations. Be
sure that power is removed or the area is nonhazardous before proceeding.
Use terminal to pass 24V dc
power to next module
in series (if necessary)
1794-APB
24V Common
Use terminal to pass 24V
common to next module
in series (if necessary)
When you connect or disconnect the PROFIBUS
cable while power is on, an electrical arc can occur
This could cause an explosion in hazardous location
installations. Be sure that power is removed or the
area is nonhazardous before proceeding.
WARNING
Profibus Connector
24V dc
Use terminal to pass 24V dc
power to next module
in series (if necessary)
Connect the PROFIBUS drop cable to the 9-pin D-shell connector
according to the following pin assignments and graphic:
Pin #
1
2
3
4
5
6
7
8
9
RS-485
Reference
B/B'
C/C'
A/A'
Signal
Shield
RP
RXD/TXD-P
CTNR-P
DGND
VP
RP
RXD/TXD-N
CTNR-N
Metal Shell
Publication CIG-WD001B-EN-P - May 2005
1
.
.
5
Description
Shield, RC to earth ground
not used
Receive/transmit data - P
not used
Data ground
Voltage plus (+5V)
not used
Receive/transmit data - N
not used
Earth Ground
6
.
.
9
DROP CABLE
Shield
Pin #1
0.01µF
500V dc
1 MΩ
Signal +
Pin #3
Signal -
Pin #8
Earth Ground
Pin #5
+5V
Data Ground
Pin #6
RCV/ Xmit Data +
RCV/ Xmit Data -
1794 FLEX I/O Modules
19-3
1794-ASB, 1794-ASB2, 1794-ASBK, 1794-ASB2K
ATTENTION
24V Common
Use terminal to pass
24V common to next module
in series (if necessary)
Connect:
To:
BLU Wire
1
Shield Wire
SH
CLR Wire
2
Power wiring must be less than 10 meters (33ft)
in length.
COM
Use terminal to pass
24V dc power to next module
in series (if necessary)
24V
WARNING
24V dc
1 SH 2
If this is the last adapter, you must terminate the
remote I/O link here. Use a terminating resistor
connected across terminals 1 and 2. Refer to your
processor manual for information on the size of
the resistor.
Remote I/O Cable Connector
(connections listed on left)
If you connect or disconnect the network cable
with power applied to the adapter or any device
on the network, an electrical arc can occur.
This could cause an explosion in hazardous
location installations. Be sure that power is
removed or the area is nonhazardous before
proceeding.
1794-IA16
1794-TBN, 1794-TBNK
Even numbered terminals 0 through 14
16
16
0
2
34
4
1
6
3
34
8
5
10
7
12
9
33
14
11
13
15
51
51
Odd numbered terminals 1 through 15
Inp ut Terminals
Chan ne l TB3, TB3K, TB3S
TBN, TBNK
0
A-0
B-0
1
A-1
C-1
2
A-2
B-2
3
A-3
C-3
4
A-4
B-4
5
A-5
C-5
6
A-6
B-6
7
A-7
C-7
16, 0, 2, 4, 6, B
8. 10. 12. 14. 33
34, 1, 3, 5, 7, C
9, 11, 13, 15, 51
33
1794-TB3, 1794-TB3K, 1794-TBB3S
0
16
1
17
34
2
18
3
19
35
4
20
36
5
6
21
37
7
22
38
8
23
39
9
24
40
10
25
41
11
26
42
27
43
44
12
13
28
45
29
14
30
46
47
15
31
48
0-15
32
49
A
33
16-33
B
51
50
34-51
120V ac Supply 1
TB3, TB3K, TB3S
C-35
C-36
C-37
C-38
C-39
C-40
C-41
C-42
Input Termin als
Channe l TB3, TB3K, TB3S
TBN, TBNK
8
A-8
B-8
9
A-9
C-9
10
A-10
B-10
11
A-11
C-11
12
A-12
B-12
13
A-13
C-13
14
A-14
B-14
15
A-15
C-15
120V ac Supply 1
TB3, TB3K, TB3S
C-43
C-44
C-45
C-46
C-47
C-48
C-49
C-50
A = Input terminals on the 1794-TB3, TB3K and TB3S. B0 - B14 and C1 -C15 are input terminals on the 1794-TBN and TBNK.
B = B-16 through B-33 are internally connected on the 1794-TB3, TB3K and -TB3S. B-16 and B-33 are internally connected on the 1794-TBN and TBNK. Connect 120V ac L2 to B-16.
C
C = C-34 through C-51 are internally connected on the 1794-TB3, TB3K and -TB3S. C-34 and C-51 are internally connected on the 1794-TBN and TBNK. Connect 120V ac L1 to C-34.
1 - Auxiliary terminal strips are required when using the 1794-TBN or TBNK.
1794-IA8, 1794-IA8K
Inpu t Channel
1794-TBN, 1794-TBNK
Even numbered terminals 0 through 14
16
16
0
2
34
4
1
6
3
5
8
10
7
9
12
11
33
14
13
15
51
Odd numbered terminals 1 through 15
34
0
1
2
3
4
5
6
7
16, 0, 2, 4, 6,
B
8. 10. 12. 14. 33
34, 1, 3, 5, 7, C
9, 11, 13, 15, 51
33
51
1794-TB2, 1794-TB3, 1794-TB3K, 1794-TB3S
0
16
1
17
34
2
3
18
35
19
36
4
20
37
5
21
38
6
22
39
7
23
40
8
24
41
9
25
42
10
26
43
11
27
44
12
28
45
13
29
46
14
30
47
15
31
48
0-15
32
49
33
50
B
51
34-51
Terminals 35 through 50 are not used on 1794-TB2
A = input terminals
B = common terminals
C = power terminals (C-34 through C-51 for TB3, TB3K and TB3S; C-34 and C-51 for TB2)
A
16-33
1794-TB2, 1794-TB3, 1794-TB3K, 1794-TBB3S
Inpu t Terminal s
120V ac Su pp ly
A-0
A-11/C-35
A-2
A-31/C-37
A-4
A-51/C-39
A-6
A-71/C-41
A-8
A-91/C-43
A-10
A-111/C-45
A-12
A-131/C-47
A-14
A-151/C-49
C
1794-TBN, 1794-TBNK
Inpu t Terminal s
120V ac Su pp ly
B-0
C-12
B-2
C-32
B-4
C-52
B-6
C-72
B-8
C-92
B-10
C-112
B-12
C-132
B-14
C-152
B = even numbered terminals B-0 through B-14, ac common
terminals B-16 and B-33
C = Power Terminals C-34 and C-51, and odd numbered
terminals 1 through 15
Connect 120V ac L2 (common) to B-16
Connect 120V ac L1 to C-34
1
2
A-1, 3, 5, 7, 9, 11, 13 and 15 on 1794-TB3, -TB3K, -TB3S, and -TB2 are internally connected in the module to 120V ac L1.
C-1, 3, 5, 7, 9, 11, 13 and 15 on 1794-TBN and TBNK are internally connected in the module to 120V ac L1.
Publication CIG-WD001B-EN-P - May 2005
19-4
1794 FLEX I/O Modules
1794-IA8I
1794-TBN, 1794-TBNK
Inpu t Channel
Even numbered terminals 0 through 14
16
16
0
2
34
4
1
6
3
5
8
10
7
12
9
11
13
Inpu t Terminal s
33
14
51
Odd numbered terminals 1 through 15
34
16, 0, 2, 4, 6, B
8. 10. 12. 14. 33
34, 1, 3, 5, 7, C
9, 11, 13, 15, 51
33
15
51
0
1
2
3
4
5
6
7
1794-TB2, 1794-TB3, 1794-TB3K, 1794-TBB3S
0
16
1
17
34
2
3
18
4
19
35
36
5
20
37
21
38
6
7
22
39
8
23
40
24
41
9
25
42
10
26
43
11
27
44
12
13
28
45
14
29
46
15
30
47
1794-TB2, 1794-TB3, 1794-TB3K, 1794-TBB3S
31
0-15
32
48
49
33
A
16-33
A = even numbered input terminals 0 thru 14 for customer input connections;
corresponding odd numbered 120V ac common L2 terminals 1 through 15 for
customer connections from isolated power supply
B
51
50
34-51
A-0
A-2
A-4
A-6
A-8
A-10
A-12
A-14
120V ac Co mmon
L2
A-1
A-3
A-5
A-7
A-9
A-11
A-13
A-15
C
Terminals 35 through 50 are not used on 1794-TB2
1794-TBN, 1794-TBNK
Inp ut Termina ls
B-0
B-2
B-4
B-6
B-8
B-10
B-12
B-14
120V ac Commo n
L2
C-1
C-3
C-5
C-7
C-9
C-11
C-13
C-15
B = even numbered input terminals 0 through 14 for
customer input connections
C = odd numbered terminals 1 through 15 for 120V ac L2
common connections from isolated power supply
Auxiliary terminal strips are required to connect 120V ac L1 of each isolated power supply to the input device that it is driving.
1794-IB10XOB6
1794-TB3, 1794-TB3K, 1794-TB3S
Inputs
0
1
2
3
4
5
Outputs
6
7
8
9
1 0
1 1
1 2
1 3
1 4
15
A
17
16
1 8
1 9
2 0
2 1
2 2
2 3
2 4
2 5
2 6
2 7
2 8
2 9
3 0
3 1
3 2
33
B
-V
Common
Commons
34
35
3 6
3 7
3 8
3 9
4 0
4 1
4 2
-V
Common
4 3
4 4
4 5
4 6
4 7
4 8
4 9
5 0
51
C
Voltage
In +V
Voltage
Out +V
Voltage
Connect +V to C-34
Connect +V common to B-16
Use B-33 and C-51 for daisy chaining to next terminal base unit
(1794-TB3 shown)
2 and 3-Wire Input Wiring
0-15 A
16-33 B
35-51 C
A = Sink Input
B = Common
C = +V dc
2-Wire Device
(Sourcing Output)
3-Wire Device
(Sourcing Output)
Sink Input Channel
0
1
2
3
4
5
6
7
8
9
Source Output Channel
0
1
2
3
4
5
+V dc
Common
Input 1
Common
Sup ply
A-0
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
B-17
B-18
B-19
B-20
B-21
B-22
B-23
B-24
B-25
B-26
C-35
C-36
C-37
C-38
C-39
C-40
C-41
C-42
C-43
C-44
A-10
A-11
A-12
A-13
A-14
A-15
B-27
B-28
B-29
B-30
B-31
B-32
C-34 through C-51
B-16 through B-33
1. Two-wire input devices use input and supply terminals. Three-wire devices use input,
common and supply terminals.
+V common internally connected to terminal 16 through 33.
+V dc power internally connected to terminal 34 through 51.
Publication CIG-WD001B-EN-P - May 2005
C-45
C-46
C-47
C-48
C-49
C-50
1794 FLEX I/O Modules
19-5
1794-IB16, 1794-IB16K, 1794-IB8
Input 1
Channel
1794-TB3, 1794-TB3K, 1794-TB3S
0
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
+V dc
Common
15
A
Inputs
17
16
1 8
19
2 0
2 1
2 2
2 3
24
2 5
2 6
2 7
2 8
2 9
3 0
3 1
32
33
B
Commons
Common
(-V)
34
35
3 6
3 7
3 8
3 9
4 0
41
Common
(-V)
4 2
4 3
4 4
4 5
4 6
4 7
4 8
4 9
5 0
51
C
+V
Voltage In
+V
Voltage Ou t
Voltage
(1794-TB3 shown)
Connect +V to C-34
Connect +V common to B-16
Use B-33 and C-51 for daisy chaining to next terminal base unit
2 and 3-Wire Input Wiring
0-15 A
16-33 B
35-51 C
Input
Terminal
Supply
Terminal
Common
Terminal
A-0
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
A-13
A-14
A-15
C-34 through C-51
C-35
C-36
C-37
C-38
C-39
C-40
C-41
C-42
C-43
C-44
C-45
C-46
C-47
C-48
C-49
C-50
B-17
B-18
B-19
B-20
B-21
B-22
B-23
B-24
B-25
B-26
B-27
B-28
B-29
B-30
B-31
B-32
2
B-16 through B-33
1. 1794-IB8 - Inputs 0 through 7; 1794-IB16 - Inputs 0 through 15
A = Sink Input
B = Common
C = +V dc
2-Wire Device
(Sourcing Output)
2. Two-wire input devices use input and supply terminals. Three-wire devices
use input, common and supply terminals.
3-Wire Device
(Sourcing Output)
+V common internally connected to terminal 16 through 33.
+V dc power internally connected to terminal 34 through 51.
1794-IB16D
1794-TB32, -TB32S
0
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
15
A
Input Terminals 0-15
17
16
1 8
19
2 0
2 1
2 2
2 3
24
2 5
2 6
2 7
2 8
2 9
3 0
3 1
32
33
B
NC
NC
Sensor Power Terminals 0-15
34
35
3 6
3 7
NC
+V1
COM1 +V1
3 8
3 9
4 0
41
4 2
4 3
4 4
4 5
4 6
4 7
4 8
4 9
5 0
51
C
COM1 +V1
COM1 +V1
COM1 +V2
COM2 +V2
COM2 +V2
COM2 +V2
COM2 NC
(1794-TB32 shown)
+ V2 = Terminals 43, 45, 47 and 49
Voltage applied to Inputs 0-15 and Sensor power 0-15
C OM1, COM2 = Terminals 36, 38, 40, 42, 44, 46, 48 and 50 Common for inputs 0 through 15 and sensor power 0 through 15
N C = No connections (terminals 16, 33, 34 and 51)
+ V1 = Terminals 35, 37, 39 and 41 (not used)
Sensor
Power
Te rminal
Input
Channel
Input
Terminal
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
+V2 dc
power
COM dc
A-0
B-17
-V common
+V2 connected
connected to
to terminals 43,
A-1
B-18
terminals 36, 38, 45, 47 and 49
A-2
B-19
40, 42, 44, 46, 48
and 50
A-3
B-20
A-4
B-21
A-5
B-22
A-6
B-23
A-7
B-24
A-8
B-25
A-9
B-26
A-10
B-27
A-11
B-28
A-12
B-29
A-13
B-30
A-14
B-31
A-15
B-32
Power terminals 43, 45, 47 and 49 (power terminals are internally
connected together in the module)
Common terminals 36, 38, 40, 42, 44, 46, 48 and 50 (common
terminals are internally connected together in the module)
Common
Supp ly
Publication CIG-WD001B-EN-P - May 2005
19-6
1794 FLEX I/O Modules
1794-IB16XOB16P
1794-TB32, -TB32S
0
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
Input
Channel
15
A
IN0
IN1
IN2
IN3
IN4
IN5
IN6
IN7
IN8
IN9
IN10
IN11
IN12
IN13
IN14
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
IN15
Inputs
17
1 8
19
2 0
2 1
2 2
OUT0
OUT1
OUT2
OUT3
OUT4
2 3
24
2 5
2 6
2 7
2 8
2 9
3 0
3 1
32
33
B
NC
OUT5
OUT6
OUT7
OUT8
OUT9 OUT10 OUT11 OUT12 OUT13 OUT14 OUT15
NC
Outputs
C
35 3 6
3 7 3 8
+V1 COM1 +V1 COM1
34
NC
3 9
+V1
4 0 41
COM1 +V1
4 2
43
44
45
COM1 +V2 COM2 +V2
46
47
COM2 +V2
+V1 = Terminals 35, 37, 39 and 41
+V2 = Terminals 43, 45, 47 and 49
COM1 = Terminals 36, 38, 40 and 42
COM2 = Terminals 44, 46, 48 and 50
NC = No connections (terminals 16, 33, 34 and 51)
48
49
50
COM2 +V2 COM2
51
NC
(1794-TB32 shown)
+V1 dc power
Com1 dc Return
2 and 3-Wire Input Wiring
0-15 A
16-33 B
35-51 C
Input
Terminal
A-0
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
A-13
A-14
A-15
Common
V1 common
connected to
terminals 36,
38, 40 and 42
Supply 1
Output
Channel
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
+V1 connected
to terminals 35,
37, 39 and 41
Power terminals 35, 37, 39 and 41
Common terminals 36, 38, 40 and 42
+V2 dc power
Com2 dc Return
Output
Terminal
B-17
B-18
B-19
B-20
B-21
B-22
B-23
B-24
B-25
B-26
B-27
B-28
B-29
B-30
B-31
B-32
Common
V2 Return
connected to
terminals 44,
46, 48 and 50
Power terminals 43, 45, 47 and 49
Common terminals 44, 46, 48 and 50
1. 2-wire input devices use input and supply terminals; 3-wire devices use input, common and supply terminals.
A = Sink Input
B = Common
C = +V dc
2-Wire Device
(Sourcing Output)
3-Wire Device
(Sourcing Output)
1794-IB32
Input
Channel
1794-TB32 and 1794-TB32S
0
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
15
A
Inputs
17
16
1 8
19
2 0
2 1
2 2
2 3
24
2 5
2 6
2 7
2 8
2 9
3 0
3 1
32
33
B
NC
NC
Inputs
34
35
3 6
NC
+V1
COM1 +V1
3 7
3 8
3 9
4 0
41
4 2
4 3
4 4
4 5
4 6
4 7
4 8
4 9
5 0
51
C
COM1 +V1
COM1 +V1
COM1 +V2
COM2 +V2
+V1 = Terminals 35, 37, 39 and 41
+V2 = Terminals 43, 45, 47 and 49
COM1 = Terminals 36, 38, 40 and 42
COM2 = Terminals 44, 46, 48 and 50
NC = No connections (terminals 16, 33, 34 and 51)
COM2 +V2
COM2 +V2
COM2 NC
(1794-TB32 shown)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
+V1 dc power
Com1 dc Return
Input
Terminal
Common
Sup ply 1
A-0
+V1 connected to
V1 common
connected to
terminals 35, 37,
A-1
terminals 36, 38, 39 and 41
A-2
40 and 42
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
A-13
A-14
A-15
Power terminals 35, 37, 39 and 41
Common terminals 36, 38, 40 and 42
Input
Channel
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
+V2 dc power
Com2 dc Return
Input
Terminal
1. 2-wire input devices use input and supply terminals; 3-wire devices use input, common and supply terminals.
Publication CIG-WD001B-EN-P - May 2005
Common
Sup ply 1
V2 common
B-17
+V2 connected to
connected to
terminals 43, 45,
B-18
terminals 44, 46, 47 and 49
B-19
48 and 50
B-20
B-21
B-22
B-23
B-24
B-25
B-26
B-27
B-28
B-29
B-30
B-31
B-32
Power terminals 43, 45, 47 and 49
Common terminals 44, 46, 48 and 50
1794 FLEX I/O Modules
19-7
1794-IC16
1794-TB3, 1794-TB3K, 1794-TB3S
0
1
0
2
1
16
17
18
34
3
2
36
5
4
19
35
4
3
20
21
37
6
5
38
6
22
7
8
9
7
8
9
23
39
24
40
41
10
10
25
26
42
43
11 12 13 14 15
11
27
44
12
28
45
13
29
14
30
46
47
15
31
48
0-15
32
49
33
A
16-33
B
51
50
34-51
C
Connect +V to C-34
Connect +V common to B-16
Use B-33 and C-51 for daisy-chaining to the next terminal base unit.
Input
Channel
Input
Terminal
0
1
2
3
4
5
6
7
Common
A-0
A-1
A-2
A-3
A-4
A-5
A-6
A-7
Supply
Terminal
C-35
C-36
C-37
C-38
C-39
C-40
C-41
C-42
B-16 through B-33
1794-TB3, 1794-TB3K, 1794-TB3S
Input
Input
Channel
Terminal
Common 1
Terminal
B-17
B-18
B-19
B-20
B-21
B-22
B-23
B-24
8
9
10
11
12
13
14
15
+V dc
A-8
A-9
A-10
A-11
A-12
A-13
A-14
A-15
Supply
Terminal
Common 1
Terminal
B-25
B-26
B-27
B-28
B-29
B-30
B-31
B-32
C-43
C-44
C-45
C-46
C-47
C-48
C-49
C-50
C-34 through C-51
1. 2-wire devices use input and supply terminals; 3-wire input devices use input, common and supply terminals.
1794-ID2
Terminal Base Units
1794-TB2, -TB3, -TB3K and -TB3S
1794-TB2, 1794-TB3, 1794-TB3K, 1794-TB3S
0 1
0
16
1
17
34
35
3
2
2
18
3
19
36
37
7 8 9
4 5 6
4
20
5
21
38
6
7
22
39
23
40
8
24
10 11 12 13 14 15
9
10
25
41
42
26
43
11
27
44
12
13
28
45
29
46
14
30
47
48
Input
0-15
15
31
32
49
50
A
16-33
33
51
34-51
B
1794-TBN, 1794-TBNF, 1794-TBNK
Even Numbered Terminals 0 through 14
16
0
34
34
2
1
4
3
6
5
8
7
10
9
12
11
33
14
13
33
15
Odd numbered terminals 1 through 15
16, 0, 2, 4, 6,
B
8, 10, 12, 14, 33
51
34, 1, 3, 5, 7,
C
9, 11, 13, 15, 51
51
Connect +V to C-34
Connect +V common to B-16
Use B-33 and C-51 for daisy-chaining to the next terminal base unit.
12/24V dc
Terminal Base Units
1794-TB2, -TB3, -TB3K and -TB3S
Input
Input
Pulse Counter Channel 0
C
Terminals 35 through 50 are not used on 1794-TB2
16
OV dc
(common)
Terminal Base Units 1
1794-TBN, -TBNK and -TBNF
OV dc
(common)
12/24V dc
Terminal Base Units 1
1794-TBN, -TBNK and -TBNF
Input
Pulse Counter Channel 1
A+
A-0
B-17
C-35
B-0
A+
A-8
B-25
C-43
A-
A-1
B-18
C-36
C-1
A-
A-9
B-26
C-44
C-9
B+
A-2
B-19
C-37
B-2
B+
A-10
B-27
C-45
B-10
C-11
B-8
B-
A-3
B-20
C-38
C-3
B-
A-11
B-28
C-46
Z+
A-4
B-21
C-39
B-4
Z+
A-12
B-29
C-47
B-12
Z-
A-5
B-22
C-40
C-5
Z-
A-13
B-30
C-48
C-13
G+
A-6
B-23
C-41
B-6
G+
A-14
B-31
C-49
B-14
G-
A-7
B-24
C-42
C-7
G-
A-15
B-32
C-50
C-15
Common
Terminals 16 and 33 (1794-TB2, -TBN, -TBNK and -TBNF)
Terminals 16 through 33 (1794-TB3, -TB3K, -TB3S)
+V dc
Terminals 34 and 51 (1794-TB2, -TBN, -TBNK and -TBNF)
Terminals 34 through 51 (1794-TB3, -TB3K, -TB3S)
1. Auxiliary terminal blocks are required when using these terminal base units.
Publication CIG-WD001B-EN-P - May 2005
19-8
1794 FLEX I/O Modules
1794-IE12
1794-TB3G, -TB3GK, -TB3GS
0
1
2
3
4
5
6
7
8
9
10
Channel
11
12
13
14
15
Input 0
A
I0 V0
I1
17
16
18
V1
19
I2 V2
20
21
I8 V8
I9
I3 V3
22
23
I4
24
V4 I5
25
26
V5
27
I6
28
V6
29
I7 V7
30
31
Input 1
32
33
B
Chassi s C0 C1
Ground
35
34
36
37
38
Input 2
V9 C2 C3 C4 C5 I10 V10 I11 V11 C6 C7 Chassi s
Ground
39
40
41
42
43
44
45
46
47
48
49
50
Input 3
51
C
Input 4
+V COM NC C8 Ch. C9
C10 Ch. C11 NC +V COM
24C dc
Gnd Chassis Grounds for Shields
Gnd
24C dc
Supply In
Supply Out
I = Current
V = Voltage
(1794-TB3G shown)
C0 thru C11 = Returns for I or V connections 0 through 11
+24V dc = Terminals C34 and C50
COM = C35 and C51
Chassis Ground = Terminals B16, B33, C38, C40 thorugh 45, and C47
NC = No connection
For daisy-chaining: Supply in - C34 (+) and C35 (-)
Supply out - C50 (+) and C51 (-)
Input 5
Input 6
Input 7
Input 8
Input 9
To reduce susceptibility to noise, power analog modules
and digital modules from separate power supplies. Do
not exceed a length of 33 ft (10m) for dc power cabling.
ATTENTION
!
Input 10
Input 11
Do not daisy chain power or ground from this terminal
base unit to any ac or dc digital module terminal
base units.
-V dc
Common
+V dc
Power
Chassis
Ground
(Shield)
Do not exceed a length of 33 ft (10m) for signal cabling.
Signal
Ty pe
Label
Ma rk in g
1794-TB3G, -TB3GK, -TB3GS
Input
Commo n
Te rm inal
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
I0
V0
I1
V1
I2
V2
I3
V3
I4
V4
I5
V5
I6
V6
I7
V7
I8
V8
I9
V9
I10
V10
I11
V11
A-0
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
A-13
A-14
A-15
B-19
B-20
B.21
B-22
B-27
B-28
B-29
B-30
B-17
B-18
B-23
B-24
B-25
B-26
B-31
B-32
C-37
C-39
C-46
C-48
Terminals 35 and 51 are internally connected in the terminal
base unit.
Terminals 34 and 50 are internally connected in the terminal
base unit.
Terminals 16, 33, 38, 40 through 45, and 47 are internally
connected to chassis ground.
1794-IE4XOE2
1794-TB2, 1794-TB3, 1794-TB3K, 1794-TB3S, 1794-TB3T and 1794-TB3TS
0
1
0
16
1
17
34
2
3
2
18
35
4
3
19
36
4
20
37
5
5
21
38
6
6
22
39
7
7
23
40
8
8
24
41
9
9
25
42
10
10
26
43
11
27
44
Channel
11 12 13 14 15
12
28
45
13
29
46
14
30
47
15
31
48
0-15
32
49
33
50
A
16-33
34-51
Terminals 35 through 50 are not used on 1794-TB2
ATTENTION
!
Only connect either a voltage input or a current input per channel, not both.
To reduce susceptibility to noise, power analog and digital modules from
separate power supplies. Do not exceed a length of 3M (9.8 ft) for DC
power cabling.
Connect +V to C-34
Connect +V common to B-16
Use B-33 and C-51 for daisy-chaining to the next terminal base unit.
In 0
B
51
C
In 1
In 2
In 3
Sign al Type
TB2, TB3,
TB3K, TB3S,
TB3T, TB3TS
Inpu t
Termi nal s
TB2, TB3,
TB3K, TB3S
TB 3T, TB 3TS
Co mmon T ermi nal s
Shi el d
Current
A-0
B-17
B-17
C-39
Voltage
A-1
B-18
B-17
C-39
Chan nel
Out 0
TB 3T, TB 3TS
Sh ie ld
Current Signal
A-8
C-43
Current Common
A-91
C-43
Current
A-2
B-19
B-19
C-40
Voltage Signal
A-10
C-44
Voltage
A-3
B-20
B-19
C-40
Voltage Common
A-111
C-44
Current
A-4
B-21
B-21
C-41
Voltage
A-5
B-22
B-21
C-41
Out 1
Current Signal
A-12
C-45
Current Common
A-131
C-45
Current
A-6
B-23
B-23
C-42
Voltage Signal
A-14
C-46
Voltage
A-7
B-24
B-23
C-42
Voltage Common
A-151
C-46
Common for TB2, TB3, TB3K, TB3S: B-16 through B-33
Common for TB3T and TB3TS: B16, 17, 19, 21, 23, 25, 27, 29, 31 and 33.
+V dc Power for 1794-TB2: C-34 and C-51;
+V dc Power for 1794-TB3, TB3K and TB3S: C-34 through C-51
+V dc Power for 1794-TB3T and -TB3TS: C-34, 35, 50 and 51
Connect any signal wiring shields to functional ground as near as possible to the module when using the 1794-TB2, -TB3, -TB3K, and -TB3S.
With the 1794-TB3T and -TB3TS, use terminals C-39 through C-46.
1. A-9, A-11, A-13 and A-15 are internally connected in the module to +V dc common.
Publication CIG-WD001B-EN-P - May 2005
Sig nal Type
TB2, TB3,
TB3K, TB3S,
TB3T, TB3TS
Output
Termi nal s
1794 FLEX I/O Modules
19-9
1794-IE8, 1794-IE8K
TB2, TB3,
TB3K, TB3S,
TB3T, TB3TS
1794-TB2, 1794-TB3, 1794-TB3K, 1794-TB3S, 1794-TB3T, 1794-TB3TS
0
1
0
16
1
17
34
2
2
18
35
3
4
3
19
36
4
20
37
5
5
21
38
6
6
22
39
7
8
9
7
8
9
23
40
24
41
25
42
10
10
26
43
11 12 13 14 15
11
27
44
Channel
12
28
45
13
29
46
14
30
47
15
31
48
0-15
32
49
A
33
16-33
0
B
51
50
Signal
Type
C
34-51
1
Terminals 35 through 50 are not used on 1794-TB2
2
ATTENTION
!
Only connect either a voltage input or a current input per channel, not both.
3
To reduce susceptibility to noise, power analog and digital modules from
separate power supplies. Do not exceed a length of 3M (9.8 ft) for DC
power cabling.
TB2, TB3,
TB3K, TB3S
Input
Terminals
TB2, TB3,
TB3K, TB3S,
TB3T, TB3TS
TB3T, TB3TS
Common Terminals
Shield
Current
A-0
B-17
B-17
C-39
Voltage
A-1
B-18
B-17
C-39
Current
A-2
B-19
B-19
C-40
Voltage
A-3
B-20
B-19
C-40
Current
A-4
B-21
B-21
C-41
Voltage
A-5
B-22
B-21
C-41
Current
A-6
B-23
B-23
C-42
Voltage
A-7
B-24
B-23
C-42
Channel
4
5
6
7
Input
Terminals
TB2, TB3,
TB3K, TB3S
TB3T, TB3TS
Common Terminals
Shield
Current
A-8
B-25
B-25
Voltage
A-9
B-26
B-25
C-43
C-43
Current
A-10
B-27
B-27
C-44
C-44
Voltage
A-11
B-28
B-27
Current
A-12
B-29
B-29
C-45
Voltage
A-13
B-30
B-39
C-45
Current
A-14
B-31
B-31
C-46
Voltage
A-15
B-32
B-31
C-46
+V dc Power for 1794-TB2: C-34 and C-51;
+V dc Power for 1794-TB3, TB3K and TB3S: C-34 through C-51
+V dc Power for 1794-TB3T and -TB3TS: C-34, 35, 50 and 51
Common for 1794-TB2, -TB3S: B-16 through B-33
Common for 1794-TB3T and -TB3TS: B-16, 17, 19, 21, 23, 25, 27, 29, 31
and 33
Connect +V to C-34
Connect +V common to B-16
Use B-33 and C-51 for daisy-chaining to the next terminal base unit.
Signal
Type
Connect any signal wiring shields to functional ground as near as possible to the module when using the 1794-TB2, -TB3, -TB3K, and -TB3S. With the
1794-TB3T and -TB3TS, use terminals C-39 through C-46.
1794-IE8H
1794-TB3G, -TB3GK, -TB3GS
0
1
2
3
4
_
+
5
17
19
2 0
2 1
2 2
3 6
COM
NC
3 7
3 8
3 9
(1794-TB3G shown)
1 0
1 1
_
1 2
24
2 5
41
4 2
2 7
2 8
2 9
_
4 3
15
A
_
3 0
3 1
32
33
B
_
+
Ch6
4 0
1 4
Ch3
2 6
+
1 3
+
Ch2
2 3
Ch5
35
9
+
_
+
Ch4
34
8
Ch1
1 8
_
+
7
_
+
Ch0
16
6
Ch7
4 4
4 5
4 6
4 7
4 8
4 9
5 0
51
NC
+V
COM
C
+V
24C dc
Supply Out
24C dc
Supply In
+24V dc = Terminals C-34 and C-50
COM = C-35 and C-51
NC = No connection
For daisy-chaining: Supply in - C-34 (+) and C-35 (-)
Supply out - C-50 (+) and C-51 (-)
Inp ut
Input
Source
In put
Signal
Input
Retu rn
Input
In put
So ur ce
Input
Signal
Input
Re turn
Input 0
A-0
A-1
A-2
Input 4
B-17
B-18
B-19
Input 1
A-4
A-5
A-6
Input 5
B-21
B-20
B-23
Input 2
A-8
A-9
A-10
Input 6
B-25
B-26
B-27
Input 3
A-12
A-13
A-14
Input 7
B-29
B-30
B-31
+V
Terminals 34 and 50
-V
Terminals 35 and 51
Publication CIG-WD001B-EN-P - May 2005
19-10
1794 FLEX I/O Modules
1794-IE8XOE4
1794-TB3G, -TB3GK, -TB3GS
0
1
2
3
4
5
6
7
8
9
10
Channel
(1794-TB3G shown)
11
12
13
14
15
Input 0
A
I0 V0
I1
17
16
18
V1
19
I2 V2
20
21
I8 V8
I9
I3 V3
22
23
I4
24
V4 I5
25
26
V5
27
I6
28
V6
29
I7 V7
30
31
Input 1
32
33
B
Chassi s C0 C1
Ground
35
34
36
37
38
Input 2
V9 C2 C3 C4 C5 I10 V10 I11 V11 C6 C7 Chassi s
Ground
39
40
41
42
43
44
45
46
47
48
49
50
Input 3
51
C
Input 4
+V COM NC C8 Ch. C9
C10 Ch. C11 NC +V COM
24C dc
Gnd Chassis Grounds for Shields
Gnd
24C dc
Supply In
Supply Out
Input 5
I = Current
V = Voltage
C0 through C11 = Returns for I or V connections 0 through 11
+24V dc = Terminals C34 and C50
COM = C35 and C51
Chassis Ground = Terminals B16, B33, C38, C40 through 45, and C47
NC = No connection
For daisy-chaining: Supply in - C34 (+) and C35 (-), Supply out - C50(+) and C51 (-)
Input 6
Input 7
Output 0
Output 1
To reduce susceptibility to noise, power analog modules
and digital modules from separate power supplies. Do
not exceed a length of 33 ft (10m) for dc power cabling.
ATTENTION
!
Output 2
Output 3
Do not daisy chain power or ground from this terminal
base unit to any ac or dc digital module terminal
base units.
-V dc
Common
+V dc
Power
Chassis
Ground
(Shield)
Do not exceed a length of 33 ft (10m) for signal cabling.
Signal
Ty pe
Label
Ma rkin g
1794-TB3G, -TB3GK, -TB3GS
Input/Output
Commo n
Te rminal
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
I0
V0
I1
V1
I2
V2
I3
V3
I4
V4
I5
V5
I6
V6
I7
V7
I8
V8
I9
V9
I10
V10
I11
V11
A-0
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
A-13
A-14
A-15
B-19
B-20
B-21
B-22
B-27
B-28
B-29
B-30
B-17
B-18
B-23
B-24
B-25
B-26
B-31
B-32
C-37
C-39
C-46
C-48
Terminals 35 and 51 are internally connected in the terminal
base unit.
Terminals 34 and 50 are internally connected in the terminal
base unit.
Terminals 16, 33, 38, 40 through 45, and 47 are internally
connected to chassis ground.
1794-IF2XOF2I
1794-TBN, 1794-TBNK
16
16
0
33
Even Numbered Terminals 0 thru 14
2
34
4
1
6
3
8
5
7
10
9
12
11
14
13
15
51
Odd Numbered Terminals 1 through 15
34
16, 0, 2, 4, 6, B
8. 10. 12. 14. 33
34, 1, 3, 5, 7, C
9, 11, 13, 15, 51
33
51
1794-TB2, -TB3, -TB3K, -TB3S, -TB3T, -TB3TS
Channel
Input 0
1794-TB2, 1794-TB3, 1794-TB3K, 1794-TB3S, 1794-TB3T, 1794-TB3TS
I
R
V
R
I
R
V
R
I
R
V
R
I
R
V
R
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
A
I
+
-
I
Current
Input
+
Current
Input
-
ac or dc
4-Wire Current
Transmitter
I
+
+
dc only
3-Wire Current
Transmitter
-
+
Current
Output
Device
Voltage
Output
Device
16-33
C
34-51
Input 1
Output 0
-
+
Current Only
2-Wire Output
Device
B
34 and 51
for T B 2
I
+
-
0-15
dc only
3-Wire Output
Device
Output 1
Common
+V dc
ATTENTION
!
Only connect either a voltage signal or a current signal per channel, not both.
Chassis Gnd
To reduce susceptibility to noise, power analog and digital modules from
separate power supplies. Do not exceed a length of 3M (9.8 ft) for DC
power cabling.
Publication CIG-WD001B-EN-P - May 2005
Signal Type
Label Marki ngs
Input/Output
Terminal
Current Input
I0
A-0
Current Return
I0 Ret
A-1
Voltage Input
V0
A-2
Voltage Return
V0 Ret
A-3
Current Input
I1
A-4
Current Return
I1 Ret
A-5
Voltage Input
V1
A-6
Voltage Return
V1 Ret
A-7
Current Output
I0
A-8
Current Return
I0 Ret
A-9
Voltage Output
V0
A-10
Voltage Return
V0 Ret
A-11
Current I Output
I1
A-12
Current Return
I1 Ret
A-13
Voltage Output
V1
A-14
Voltage Return
V1 Ret
A-15
Shiel d (TB 3T/TB 3TS)
1794-TBN,
-TBNK
Input
Terminal
C-39
C-40
C-41
C-42
C-43
C-44
C-45
C-46
B-0
C-1
B-2
C-3
B-4
C-5
B-6
C-7
B-8
C-9
B-10
C-11
B-12
C-13
B-14
C-15
TB2, TB3, TB3K TB3S: Terminals 16 through 33 are internally connected in the terminal base unit.
TB3T, TB3TS: Terminals 16, 17, 19, 21, 23, 25, 27, 29, 31, and 33 are internally connected in the terminal base unit
TBN, TBNK: Terminals 16 and 33 are internally connected in the terminal base unit.
TB2, TBN, TBNK: Terminals 34 and 51 are internally connected in the terminal base unit.
TB3, TB3K, TB3S: Terminals 34 through 51 are internally connected in the terminal base unit.
TB3T, TB3TS: Terminals 34, 35, 50, and 51 are internally connected in the terminal base unit
TB3T, TB3TS: Terminals 39 through 46 are internally connected to chassis gnd
Connect any signal wiring shields to functional ground as near as possible to the module when using the 1794-TB2, -TB3, -TB3K, and -TB3S.
With the 1794-TB3T and -TB3TS, use terminals C-39 through C-46 for signal wiring shields.
Connect +V to C-34.
Connect +V common to B-16.
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
1794 FLEX I/O Modules
19-11
1794-IF4I
1794-T B N, 1794-TBNK
Even Numbered Terminals 0 through 14
16
16
0
2
34
4
1
6
3
8
5
10
7
9
12
11
33
14
13
15
51
Odd Numbered Terminals 1 through 15
34
16, 0, 2, 4, 6, B
8. 10. 12. 14. 33
34, 1, 3, 5, 7, C
9, 11, 13, 15, 51
33
51
1794-TB2, -TB3, -TB3K, -TB3S, -TB3T, -TB3TS
Input
Channel
0
1794-TB2, 1794-TB3, 1794-TB3K, 1794-TB3S, 1794-TB3T, 1794-TB3TS
La bel Ma rkings
Current Input
I0
A-0
Current Return
I0 Ret
A-1
Voltage Input
V0
A-2
I
R
V
R
I
R
V
R
I
R
V
R
I
R
V
R
Voltage Return
V0 Ret
A-3
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Current Input
I1
A-4
Current Return
I1 Ret
A-5
Voltage Input
V1
A-6
Voltage Return
V1 Ret
A-7
Current Input
I2
A-8
Current Return
I2 Ret
A-9
Voltage Input
V2
A-10
Voltage Return
V2 Ret
A-11
Current Input
I3
A-12
Current Return
I3 Ret
A-13
Voltage Input
V3
A-14
Voltage Return
V3 Ret
A-15
A
0-15
B
16-33
C
34-51
1
I
Signal Type
Input
Terminal
+
-
I
Current
Input
Current
Input
-
I
+
-
+
-
ATTENTION
!
dc only
3-Wire Current
Transmitter
Voltage
Input
24V dc
Power Supply
+
ac or dc
4-Wire Current
Transmitter
+
Current
Input
+
+
I
Current Only
2-Wire Current
Transmitter and External
Power Supply
34 & 51
for TB2
2
-
+
3
dc only
3-Wire
Transmitter
Only connect either a voltage input or a current input per channel, not both.
To reduce susceptibility to noise, power analog and digital modules from
separate power supplies. Do not exceed a length of 3M (9.8 ft) for DC
power cabling.
Common
+V dc
Chassis Gnd
1794-TBN, -TBNK
Shiel d (TB 3T/TB 3TS)
C-39
C-40
C-41
C-42
C-43
C-44
C-45
C-46
Input
Terminal
B-0
C-1
B-2
C-3
B-4
C-5
B-6
C-7
B-8
C-9
B-10
C-11
B-12
C-13
B-14
C-15
TB2, TB3, TB3K, TB3S: Terminals 16 through 33 are internally connected in the terminal base unit
TB3T, TB3TS: Terminals 16, 17, 19, 21, 23, 25, 27, 29, 31, and 33 are internally connected in the terminal base unit
TBN, TBNK: Terminals 16 and 33 are internally connected in the terminal base unit
TB2,TBN, TBNK: Terminals 34 and 51 are internally connected in the terminal base unit
TB3, TB3K, TB3S: Terminals 34 through 51 are internally connected in the terminal base unit
TB3T, TB3TS: Terminals 34, 35, 50, and 51 are internally connected in the terminal base unit
TB3T, TB3TS: Terminals 39 through 46 are internally connected to chassis gnd
Connect any signal wiring shields to functional ground as near as possible to the module when using the 1794-TB2, -TB3, -TB3K, -TB3S, -TBN and -TBNK.
With the 1794-TB3T and -TB3TS, use terminals C-39 through C-46 for signal wiring shields.
Connect +V to C-34.
Connect +V common to B-16.
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
Publication CIG-WD001B-EN-P - May 2005
19-12
1794 FLEX I/O Modules
1794-IJ2, 1794-IJ2K
Connections are for 1794-TB3G, -TB3GK and -TB3GS
(TB3G shown)
Channel 0 Frequency Input
A
0
1
2
3
4
3V
6V
24V
Pwr
RET
50
mV
Sel
Channel 1 Frequency Input
5
6
7
8
9
24V
Pwr
24V
Pwr
10
11
12
13
14
15
Row 1
500/50
mV
F
F
500/50
mV
Channel 0 Gate Input
16
B
17
18
19
Out 0
Out 0
Ret
20
21
22
23
24
25
26
50
mV
Sel
RET
Channel 1 Gate Input
27
28
24V
Pwr
29
6V
30
All '24V Pwr' and 'RET' terminals
are sourced power provided for
the sensors. Do not connect external
power to these terminals.
3V
31
32
These outputs provide power for up
to four 24Vdc devices at 15mA each--for
a total of 60mA. Channel 0 '24V Pwr'
and channel 1 '24V Pwr' are each current
limited to 30mA maximum.
33
Row 2
NC
RET
50
mV
Sel
500/50
mV
G
24V
Pwr
24V
Pwr
G
500/50
mV
50
mV
Sel
RET
Out 1
NC
Out 1
Ret
Chassis Gnd
Chassis Gnd
34
C
35
36
COM
NC
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Row 3
+V
Sply
0
Chassis Sply 0
Gnd Ret
Sply
1
6 Chassis Ground
for Shields
Channel 0 Output Supply
24V dc
Supply In
Chassis Sply 1
Ret
Gnd
+V
NC
Channel 1 Output Supply
COM
24V dc
Supply Out
NC = No connect
Channel 0 Termi nals 5
Type of
In pu ts
Inpu t
RET 6
Pow er
Inpu t
RET 6
24V dc
IEC 3
Proximity1,2
B-24
B-23
B-20
B-25
B-26
B-29
A-12
24V dc
Contact
Switch3
B-24
B-23
B-20
B-25
B-26
B-29
A-10
A-12
500mV ac
Magnetic
Pickup
B-24
B-22
B-20
B-25
B-27
B-29
A-8
A-10
A-12
50mV ac
Magnetic
Pickup4
B-24
B-22
B-20
B-25
B-27
B-29
A-13
A-14
A-12
1
RET 6
Pow er
Inpu t
RET 6
24V dc
IEC 3
Proximity1,2
A-7
A-6
A-3
A-8
A-9
A-12
24V dc
Contact
Switch3
A-7
A-6
A-3
A-8
A-9
500mV ac
Magnetic
Pickup
A-7
A-5
A-3
A-8
50mV ac
Magnetic
Pickup4
A-7
A-5
A-3
6V ac
Vortex
A-2
A-1
A-3
Gate
Frequency
1
2
3
4
5
6
Type of
Inputs
2
A-2
A-0
A-3
A-13
A-15
A-12
As defined by standard IEC 1131-2.
RET not used on 2-wire devices.
Add external resistor from 24V to F or G for wire-off detection (0.4mA).
Add a jumper between 50mV and RET (Frequency - channel 0=4 to 3; channel 1=11 to
12). (Gate - channel 0=21 to 20; channel 1=28 to 29).
Connect cable shields to Chassis Gnd terminals.
All 4 RET terminals (ch 0 and 1, Freq, Gate) are internally connected together.
3
4
5
6
As defined by standard IEC 1131-2.
RET not used on 2-wire devices.
Add external resistor from 24V to F or G for wire-off detection (0.4mA).
Add a jumper between 50mV and RET (Frequency - channel 0=4 to 3; channel 1=11 to
12). (Gate - channel 0=21 to 20; channel 1=28 to 29).
Connect cable shields to Chassis Gnd terminals.
All 4 RET terminals (ch 0 and 1, Freq, Gate) are internally connected together.
Chan nel 0 Termi nal s 1
Output Al arm
Co nne ct ion s
Sply
+
Sply
RET
Supply Connection
C-37
C-39
Output Connection
1
ATTENTION
!
Ch ann el 1 Term ina ls 5
Pow er
Inpu t
3V ac
Vortex
Ch anne l 0 Termi nals 5
Ch ann el 1 Termina ls 5
Pow er
Ou t
+
Ou t
RET
B-17
B-18
Chan nel 1 Termi nal s 1
Sply
+
Sply
RET
C-46
C-48
Ou t
+
Ou t
RET
B-31 B-32
Connect cable shields to Chassis Gnd terminals.
To reduce the susceptibility to noise, power analog modules and digital modules from separate power supplies. Do not exceed a length of 10m (33ft) for dc
power cabling.
Do not daisy chain power or ground from this module to any ac or dc digital module terminal base unit.
Also, total current draw through the terminal base unit is limited to 10A. Separate power connections to the terminal base unit may be necessary.
Publication CIG-WD001B-EN-P - May 2005
1794 FLEX I/O Modules
19-13
1794-IM8
1794-T B N, 1794-TBNK
16
16
Even Numbered Terminals 0 through 14
0
2
34
4
1
6
3
8
5
10
7
12
9
11
33
14
13
15
51
Odd Numbered Terminals 1 through 15
34
16, 0, 2, 4, 6, B
8. 10. 12. 14. 33
34, 1, 3, 5, 7, C
9, 11, 13, 15, 51
33
51
Connect 220V ac L2 to B-16; B-16 and B-33 are connected internally.
Connect 220V ac L1 to C-34; C-34 and C-51 are connected internally.
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
Inpu t Channel
0
1
2
3
4
5
6
7
Inpu t Terminal s
B-0
B-2
B-4
B-6
B-8
B-10
B-12
B-14
220V a c Su pp ly
C-1
C-3
C-5
C-7
C-9
C-11
C-13
C-15
1
1. Terminals C-1, 3, 5, 7, 9, 11, 13 and 15 are connected internally to 220V ac L1.
1794-IP4
Ch annel
Signal
Name 1
Terminal Base Units
1794-TB3, -TB3K and -TB3S
Input
1794-TB3, -TB3K, -TB3S
0V dc
(Common)
2
Terminal Base Units
1794-TBN, -TBNK -TBNF
12/24V d c
Input
16-Bit Period Time Measurement
1
0
1
16
17
18
34
35
3
2
2
19
36
4
20
37
7 8 9
4 5 6
3
5
21
38
6
7
22
39
23
40
8
24
10 11 12 13 14 15
9
10
25
41
42
26
43
11
27
44
12
13
28
45
29
46
14
30
47
0-15
15
31
48
32
49
50
51
0
A
16-33
33
34-51
B
1
C
2
1794-TBN, -TBNK, -TBNF
3
Even numbered terminals 0 through 14
16
16
0
34
34
2
1
4
3
6
5
8
7
10
9
12
11
33
14
13
Odd numbered terminals 1 through 15
33
15
16, 0, 2, 4, 6,
B
8, 10, 12, 14, 33
51
34, 1, 3, 5, 7,
C
9, 11, 13, 15, 51
51
N
A-0
B-17
C-35
B-0
N
A-1
B-18
C-36
C-1
N
A-2
B-19
C-37
B-2
N
A-3
B-20
C-38
C-3
N
A-4
B-21
C-39
B-4
N
A-5
B-22
C-40
C-5
N
A-6
B-23
C-41
B-6
N
A-7
B-24
C-42
C-7
D
A-8
B-25
C-43
D
A-9
B-26
C-44
C-9
D
A-10
B-27
C-45
B-10
D
A-11
B-28
C-46
C-11
D
A-12
B-29
C-47
B-12
D
A-13
B-30
C-48
C-13
32-B it Period T ime Me as urem ent
0
1
Connect +V to C-34
Connect +V common to B-16
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
2
3
D
A-14
B-31
C-49
B-14
D
A-15
B-32
C-50
C-15
Common
+V dc
1
2
B-8
Terminals 16 through 33
Terminals 16
and 33
Terminals 34 through 51
Terminals 34
and 51
Any unused signals have to be connected to the associated common.
Auxilary terminal blocks are required when using these terminal base units.
Publication CIG-WD001B-EN-P - May 2005
19-14
1794 FLEX I/O Modules
1794-IR8
1794-TB2, -TB3, -TB3K, -TB3S, -TB3T, -TB3TS
0 1 2 3 4 5 6 7 8 9 10 1112 1314 15
0
1
17
16
2
18
34
19
35
3
20
36
4
21
37
5
22
38
6
23
39
7
24
40
8
25
41
9
26
42
10
11
27
43
12
28
44
13
29
45
30
46
14
31
47
15
32
48
33
49
High Signal
0
A-0
A-1
B-17
B-18
C-39
B
1
A-2
A-3
B-19
B-20
C-40
34-51 C
2
A-4
A-5
B-21
B-22
C-41
3
A-6
A-7
B-23
B-24
C-42
4
A-8
A-9
B-25
B-26
C-43
5
A-10
A-11
B-27
B-28
C-44
6
A-12
A-13
B-29
B-30
C-45
7
A-14
A-15
B-31
B-32
C-46
A
0-15
16-33
Use the following Belden cables for connecting the
RTD to the terminal base unit.
!
RTD Type
Belden Cable
Number
Length of Run/Humidity Level
3-wire
Common
TB2, TB3, TB3S
TB3T, TB3TS
B-16 through B-33 for 1794-TB2, -TB3, -TB3K and -TB3S
B-16, B-17, B-19, B-21, B-23, B-25, B-27, B-29, B-31 and B-33 for 1794-TB3T and -TB3TS
9501
Not applicable
2-wire
Low Signal
51
50
Terminals 35 through 50 are not used on the 1794-TB2
ATTENTION
Shield Return
Signal
Ret urn 1
Channel
C-34 through C-51 for 1794-TB3, -TB3K and -TB3S; C-34 and C-51 for 1794-TB2
C-34, C-35, C-50 and C-51 for 1794-TB3T and -TB3TS
+V dc
Less than 100 ft (30.5m)
with normal humidity
9533
Over 100 ft (30.5m) or
high humidity1
8350 3
1. When using a 2-wire RTD, jumper the signal return to the low signal terminal.
2. B-18, B-20, B-22, B-24, B-26, B-28, B-30 and B-32 are tied to Common on 1794-TB2, -TB3, -TB3K, -TB3S;
C-39 through C-46 are tied to chassis ground on 1794-TB3T and 1794-TB3ST
1 Greater than 55% for more than 8 hours
Connect +V to C-34
Connect +V common to B-16
Use B-33 and C-51 for daisy chaining to the next terminal base unit
To reduce the susceptibility to noise, power analog
modules and digital modules from separate power
supplies. Do not exceed a length of 3m (9.8ft) for dc
power cabling.
Do not daisy chain power or ground from the RTD
terminal base unit to any ac or dc digital module
terminal base unit.
1794-IRT8, 1794-IRT8K
1
RTD
2-Wire
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
+
H
L
-
+
H
L
-
+
H
L
-
+
H
L
-
3-Wire
0-15
Channel 0
16
17
Channel 1
18
19
20
21
22
Channel 2
23
24
25
26
28
29
30
H
L
-
+
H
Channel 4
L
-
+
H
Channel 5
L
-
+
31
H
Channel 6
32
L
36
37
38
39
40
41
42
43
44
45
46
47
48
COM
NC
24V dc
Supply In
Chassis
GND
CJC
6 Chassis Ground
for Shields
Chassis
GND
CJC
!
H
L
RTD - 3-wire
49
NC
+
-
1
2
3
1
2
2a
1
RTD - 2-wire
50
RTD - 4-wire
51
+V
C
1a
Sh ie ld 1
2
Thermocouple
1
2
Millivolt
1
2
1 Terminals B-16, B-33 and C-40 through C-45 are Chassis Gnd for signal wire shields.
COM
24V dc
Supply Out
NC = No connect
ATTENTION
Connect the following
Ty pe of Input
Channel 7
34-51
+V
B
Chassis Gnd
35
2
4-Wire
33
-
Chassis Gnd
34
Millivolt
2
16-33
+
1
+
mV
-
1
1a
2a
A
Channel 3
27
2
1
3
2
Connections for 1794-TB3G, -TB3GK and -TB3GS (TB3G shown)
0
1
Thermocouple
2
To reduce the susceptibility to noise, power analog modules and digital modules from separate power
supplies. Do not exceed a length of 3m (9.8ft) for dc power cabling.
Do not daisy chain power or ground from this module to any ac or dc digital module terminal base unit.
RTD or
Ther mocouple
Channel
1794-TB3G, -TB3GK and -TB3GS Terminal Base Units
High Signal
Lo w Signal
RTD Source
Signal
Te rm in al (H ) Te rminal (L ) Cu rre nt (+ ) Return (- )
0
A-1
A-2
A-0
1
A-5
A-6
A-4
A-7
2
A-9
A-10
A-8
A-11
3
A-13
A-14
A-12
A-15
4
B-18
B-19
B-17
B-20
5
B-22
B-23
B-21
B-24
6
B-26
B-27
B-25
B-28
7
B-30
B-31
B-29
B-32
+V dc
C-34 and 50 - Connect +V to C-34
Common
C-35 and 51 - Connect +V common to C-35
A-3
CJC Sensor
Input
+
Chassis Ground
_
CJC Tail 1
CJC1
37
38
39
5 (22)
CJC2
46
47
48
12 (29)
1 - Use pins 5 and 12 when channels 0-7 are configured as thermocouples. Use pins 12 and
29 when only channels 4-7 are configured as thermocouples.
Publication CIG-WD001B-EN-P - May 2005
1794 FLEX I/O Modules
19-15
1794-IT8
1794-TB2, -TB3, -TB3K, -TB3S, -TB3T, -TB3TS
0
0
1
17
16
Shield Return
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
2
18
34
3
19
20
35
36
4
5
21
37
6
22
38
23
39
7
8
24
40
9
25
41
26
42
10
27
43
11
12
28
44
29
45
13
30
46
14
47
32
48
33
49
A
0-15
15
31
16-33
Channel
High Signal
0
A-0
1
B
51
50
C
34-51
Terminals 35 through 50 are not used on the 1794-TB2
To reduce the susceptibility to noise, power analog
modules and digital modules from separate power
supplies. Do not exceed a length of 3m (9.8ft) for dc
power cabling.
ATTENTION
!
1
TB2, TB3,
TB3K, TB3S
TB3T, TB3TS
A-1
B-17
C-39
A-2
A-3
B-19
C-40
2
A-4
A-5
B-21
C-41
3
A-6
A-7
B-23
C-42
4
A-8
A-9
B-25
C-43
5
A-10
A-11
B-27
C-44
6
A-12
A-13
B-29
C-45
7
A-14
A-15
B-31
C-46
Common
Do not daisy chain power or ground from this terminal
base unit to any ac or dc digital module terminal
base unit.
Low Signal
B-16 through B-33 for 1794-TB2, -TB3, -TB3K and -TB3S
B-16, B-17, B-19, B-21, B-23, B-25, B-27, B-29, B-31 and B-33 for
1794-TB3T and -TB3TS
C-34 through C-51 for 1794-TB3, -TB3K and -TB3S; C-34 and C-51 for 1794-TB2
C-34, C-35, C-50 and C-51 for 1794-TB3T and -TB3TS
+V dc
1. B-17, B-19, B-21, B-23, B-25, B-27, B-29 and B-31 are tied to Common on 1794-TB2, -TB3, -TB3S;
C-39 through C-46 are tied to chassis ground on 1794-TB3T and 1794-TB3TS
Use 1794-TB3T or -TB3TS for thermocouple or millivolt inputs. Use 1794-TB2, -TB3 and -TB3S
for millivolt inputs only.
Connect +V to C-34.
Connect +V common to B-16.
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
1794-TG3T and 1794-TB3TS
CJC Sensor
Input
CJC1
36
Chassis
Ground
37
CJC2
47
48
+
_
38
49
CJC
Tail
A0 through A7
(any terminal)
A8 through A15
(any terminal)
The tail of the cold junction compensator shares a terminal with an input.
1794-IV16
1794-TB2, -TB3, -TB3K, -TB3S
1794-TB2, -TB3, -TB3K, -TB3S
0
1
0
16
1
17
34
2
2
18
35
3
3
19
36
4
20
37
5
4
5
21
38
6
6
22
39
7
8
9
7
8
9
23
40
24
41
25
42
10
10
26
43
11 12 13 14 15
11
27
44
12
28
45
13
29
46
14
30
47
15
31
48
0-15
32
49
33
50
A
16-33
51
34-51
Terminals 35 through 50 are not used on 1794-TB2
B
C
Input
Channel
0
1
2
3
4
5
6
7
Common
Input
Common
Terminal
Terminal
A-0
B-17
A-1
B-18
A-2
B-19
A-3
B-20
A-4
B-21
A-5
B-22
A-6
B-23
A-7
B-24
B-16 through B-33
Input
Channel
8
9
10
11
12
13
14
15
+V dc
Input
Terminal
A-8
A-9
A-10
A-11
A-12
A-13
A-14
A-15
Common
Terminal
B-25
B-26
B-27
B-28
B-29
B-30
B-31
B-32
C-34 through C-51
(C-34 and C-51 for TB2)
Connect +V to C-34.
Connect +V common to B-16.
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
Publication CIG-WD001B-EN-P - May 2005
19-16
1794 FLEX I/O Modules
1794-OA16
1794-TBN, -TBNK
16
Channe l
33
Even Numbered Terminals 0 through 14
16
0
2
34
4
1
6
3
8
5
10
7
12
9
14
11
13
15
51
Odd Numbered Terminals 1 through 15
34
16, 0, 2, 4, 6,
B
8. 10. 12. 14. 33
34, 1, 3, 5, 7, C
9, 11, 13, 15, 51
33
51
0
1
2
3
4
5
6
7
1794-TB2, -TB3, -TB3K, -TB3S
0
1
16
2
17
3
18
34
4
19
35
5
20
36
6
21
37
7
22
38
8
23
39
40
9
24
25
41
10
11
26
42
12
27
43
44
13
28
29
45
14
15
30
46
31
47
A
0-15
32
48
33
49
34-51
120V ac Common 1
Output Termin als
1794-TB2, -TB3, Cha nne l 1794-TB2, -TB3, 1794-TBN,
-TB3K, -TB3S
-TB3K, -TB3S
-TBNK
B-17
8
A-8
B-8
B-18
9
A-9
C-9
B-19
10
A-10
B-10
B-20
11
A-11
C-11
B-21
12
1-12
B-12
B-22
13
A-13
C-13
B-23
14
A-14
B-14
B-24
15
A-15
C-15
120V ac Common 1
1794-TB2, -TB3,
-TB3K, -TB3S
B-25
B-26
B-27
B-28
B-29
B-30
B-31
B-32
For TB2, -TB3, -TB3K and -TB3S:
A = Output terminals.
B = B-17 through B-32 are connected internally to 120V ac common L2. Connect 120V ac common L2 to B-16.
C = Power terminals (C-34 and C-51 for TB2; C-34 through C-51 for TB3 and TB3S) are connected internally. Connect 120V ac L1 to terminal C-34.
For -TBN and -TBNK: Connect 120V ac common L2 to B-16. Connect 120V ac L1 to C-34.
B = Even numbered output terminals 0 through 14; B-16 and B-33 are connected internally.
C = Odd numbered output terminals 1 through 15; C-34 and C-51 are connected internally.
B
16-33
51
50
Ou tput Terminal s
1794-TB2, -TB3,
1794-TBN,
-TB3K, -TB3S
-TBNK
A-0
B-0
A-1
C-1
A-2
B-2
A-3
C-3
A-4
B-4
A-5
C-5
A-6
B-6
A-7
C-7
C
Terminals 35 through 50 are not used on 1794-TB2
1. When using the 1794-TBN and -TBNK, an auxiliary terminal block must be used to provide connection points for each channel's second sensor wire,
120V ac common. Use B-33 and C-51 for daisy chaining to the next terminal base unit.
1794-OA8, 1794-OA8K
1794-TB2, -TB3, -TB3K, -TB3S
1794-TBN, -TBNK, -TBNF
16
33
Even Numbered Terminals 0 through 14
16
0
2
34
4
1
6
3
8
5
10
7
12
9
14
11
13
15
51
Odd Numbered Terminals 1 through 15
34
16, 0, 2, 4, 6,
B
8. 10. 12. 14. 33
34, 1, 3, 5, 7, C
9, 11, 13, 15, 51
33
51
1794-TB2, -TB3, -TB3K, -TB3S
0
1
16
2
17
3
18
34
19
35
4
5
20
36
6
21
37
7
22
38
8
23
39
40
9
24
10
25
41
26
42
11
27
43
12
28
44
13
29
45
14
30
46
15
31
47
48
0-15
32
49
33
51
50
B
34-51
Ou tpu t Termin al
0
1
2
3
4
5
6
7
A-0
A-2
A-4
A-6
A-8
A-10
A-12
A-14
C
Terminals 35 through 50 are not used on 1794-TB2
1794-TBN, -TBNK, -TBNF
Ou tpu t Termin al
Common Termin al 1
A-1 /B-17
A-3 /B-19
A-5 /B-21
A-7 /B-23
A-9 /B-25
A-11 /B-27
A-13 /B-29
A-15 /B-31
A = output terminals
B = common terminals - 120V ac Common L2
C = Power terminal (C-34 through 51 for TB3, TB3K and TB3S) (C-34 and C-51 for TB2)
A
16-33
Output Channel
B-0
B-2
B-4
B-6
B-8
B-10
B-12
B-14
Common Termin al 2
C-1
C-3
C-5
C-7
C-9
C-11
C-13
C-15
B = even numbered terminals 0 through 14, ac common L2
terminals 16 and 33
C = Power Terminals C-34 and C-51, and odd numbered
common terminals 1 through 15
1. A-1, 3, 5, 7, 9, 11, 13 and 15 on 1794-TB3, -TB3K, -TB3S and -TB2 are connected internally to 120V ac common L2.
2. C-1, 3, 5, 7, 9, 11, 13 and 15 on 1794-TBN, -TBNK and -TBNF are connected internally to 120V ac common L2.
Connect 120V ac L1 to C-34.
Connect 120V ac L2 common to B-16.
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
1794-OA8I
1794-TBN, -TBNK, -TBNF
33
Even Numbered Terminals 0 through 14
16
16
0
2
34
4
1
6
3
5
8
10
7
9
12
11
14
13
15
51
Odd Numbered Terminals 1 through 15
34
16, 0, 2, 4, 6,
8. 10. 12. 14. 33 B
33
Output Channel
34, 1, 3, 5, 7, C
9, 11, 13, 15, 51
51
1794-TB2, -TB3, -TB3K, -TB3S
0
16
1
17
34
2
18
35
3
19
36
4
20
37
5
21
38
6
22
39
7
23
40
8
24
41
9
25
42
10
26
43
11
27
44
12
28
45
13
29
46
14
30
47
15
31
48
Terminals 35 through 50 are not used on 1794-TB2
Publication CIG-WD001B-EN-P - May 2005
0-15
32
49
33
50
A
16-33
51
34-51
B
C
0
1
2
3
4
5
6
7
1794-TB2, -TB3, -TB3K, -TB3S
Ou tpu t Termin al 120V ac L1 Termin al
A-0
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
A-13
A-14
A-15
A = even numbered output terminals 0 through 14
odd numbered 120V ac L1 terminals 1 through 15
1794-TBN, -TBNK, -TBNF
Ou tpu t Termin al 120V ac L1 Termin al
B-0
C-1
B-2
C-3
B-4
C-5
B-6
C-7
B-8
C-9
B-10
C-11
B-12
C-13
B-14
C-15
B = even numbered output terminals 0 through 14
C = odd numbered 120V ac L1 terminals 1 through 15
1794 FLEX I/O Modules
19-17
1794-OB16, 1794-OB16D, 1794-OB16P, 1794-OB16PK, 1794-OB8
Output 1
Channel
Output
Terminal
Common
Terminal
0
A-0
B-17
1
A-1
B-18
2
A-2
B-19
3
A-3
B-20
4
A-4
B-21
5
A-5
B-22
6
A-6
B-23
7
A-7
B-24
-V
Common
8
A-8
B-25
5 0
9
A-9
B-26
10
A-1 0
B-27
11
A-1 1
B-28
12
A-1 2
B-29
13
A-1 3
B-30
14
A-1 4
B-31
15
A-1 5
B-32
1794-TB2, -TB3, -TB3K and -TB3S
Outputs
0
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
15
A
17
16
1 8
19
2 0
2 1
2 2
2 3
24
2 5
2 6
2 7
2 8
2 9
3 0
3 1
32
33
B
-V
Co mmon
Commons
35
34
3 6
3 7
3 8
3 9
4 0
41
4 2
4 3
4 4
4 5
4 6
4 7
4 8
4 9
51
C
V oltage
In +V
Voltage
Out +V
Terminals 35 through 50 not available on 1794-TB2
Voltage
(1794-TB3 shown)
Connect +V to C-34.
Connect +V common to B-16.
Use B-33 and C-51 for daisy chaining to next terminal base unit.
+V d c
C-34 and C-51 for 1794-TB2
C-34 through B-51 for the 1794-TB3,
-TB3K and -TB3S
Com m on
B-16 through B-33
1. 1794-OB8 uses only outputs 0 through 7.
1794-OB32P
1794-TB32 and -TB32S
0
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
15
A
Outputs
17
16
1 8
19
2 0
2 1
2 2
2 3
24
2 5
2 6
2 7
2 8
2 9
3 0
3 1
32
33
B
NC
NC
Outputs
34
35
3 6
3 7
3 8
3 9
4 0
41
4 2
4 3
4 4
4 5
4 6
4 7
4 8
4 9
5 0
51
+V2 COM2
NC
C
NC
+V1 COM1
+V1 COM1
+V1 COM1
+V1 COM1
+V2 COM2
+V1 = Terminals 35, 37, 39 and 41
+V2 = Terminals 43, 45, 47 and 49
COM1 = Terminals 36, 38, 40 and 42
COM2 = Terminals 44, 46, 48 and 50
NC = No connections (terminals 16, 33, 34 and 51)
+V2 COM2
+V2 COM2
(1794-TB32 shown)
Output
Channel
Output
Terminal
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
A-0
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
A-13
A-14
A-15
Co mmon
Connect common
to terminals 36,
38, 40 and 42
For Outputs 0 through 15, use +V1 and COM1
+V1 dc power
Power terminals 35, 37, 39 and 41
Com1 dc Return
Common terminals 36, 38, 40 and 42
Output
Channel
Output
Terminal
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
B-17
B-18
B-19
B-20
B-21
B-22
B-23
B-24
B-25
B-26
B-27
B-28
B-29
B-30
B-31
B-32
Co mmon
Connect common
to terminals 44,
46, 48 and 50
For Outputs 16 through 31, use +V2 and COM2
+V2 dc power
Power terminals 43, 45, 47 and 49
Com2 dc Return
Common terminals 44, 46, 48 and 50
Publication CIG-WD001B-EN-P - May 2005
19-18
1794 FLEX I/O Modules
1794-OB8EP, 1794-OB8EPK
1794-TB2, -TB3, -TB3K, -TB3S
1794-TB2, -TB3, -TB3K, -TB3S
1794-TBN, -TBNK
Ou tput
Co mmo n
Ou tput
Co mmo n
Te rminal
Te rminal 1 Te rminal
Te rminal 2
Outputs
0
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
15
Output
Channel
A
17
16
1 8
19
2 0
2 1
2 2
2 3
24
2 5
2 6
2 7
2 8
2 9
3 0
3 1
32
33
0
1
2
3
4
5
6
7
B
34
-V
Common
Commons
-V
Co mmon
35
3 6
3 7
3 8
3 9
4 0
41
4 2
4 3
4 4
4 5
4 6
4 7
4 8
4 9
5 0
51
C
V oltage
In +V
Voltage
Out +V
Terminals 35 through 50 not available on 1794-TB2
Voltage
(1794-TB3 shown)
1794-TBN, -TBNK
Even Numbered I/O Terminals 0 thru 14
COM
4
2
0
6
8
10
14
12
A-1/B-17
A-3/B-18
A-5/B-19
A-7/B-20
A-9/B-21
A-11/B-22
A-13/B-23
A-15/B-24
B-0
B-2
B-4
B-6
B-8
B-10
B-12
B-14
C-1
C-3
C-5
C-7
C-9
C-11
C-13
C-15
C-34 through C-51 for 1794-TB3, -TB3K and -TB3S
C-34 and C-51 for 1794-TB2, -TBN and -TBNK
+V dc
COM
16
A-0
A-2
A-4
A-6
A-8
A-10
A-12
A-14
33
B
34
3
1
5
11
9
7
13
51
15
+V
B-16 through B-33 for 1794-TB2, -TB3, -TB3K, -TB3S
B-16 and B33 for 1794-TBN and -TBNK
Common
C
+V
1. For the 1794-TB2, -TB3, -TB3K, -TB3S terminal bases, the A-1, A-3, A-5, A-7, A-9, A-11,
A-13 and A-15 are connected internally to 24V dc common.
Odd Numbered I/O Terminals 1 thru 15
Connect +V to C-34.
Connect +V common to B-16.
2. For the 1794-TBN and -TBNK terminal bases, the C-1, C-3, C-5, C-7, C-9, C-11,
C-13 and C-15 are connected internally to 24V dc common.
Use B-33 and C-51 for daisy chaining to next terminal base unit.
1794-OC16
1794-TB2, -TB3, -TB3K, -TB3S
1794-TB2, -TB3, -TB3K, -TB3S
0
1
0
16
1
17
34
2
2
18
35
3
3
19
36
4
20
37
5
4
5
21
38
6
6
22
39
7
8
9
7
8
9
23
40
24
41
25
42
10
10
26
43
11 12 13 14 15
11
27
44
12
28
45
13
29
46
14
30
47
15
31
48
0-15
32
49
33
50
A
16-33
34-51
Terminals 35 through 50 are not used on 1794-TB2
Connect +V to C-34.
Connect +V common to B-16.
Use B-33 and C-51 for daisy chaining to next terminal base unit.
B
51
C
Output
Channel
Output
Terminal
Common
Terminal
Output
Channel
Output
Terminal
Common
Terminal
0
A-0
B-17
8
A-8
B-25
1
A-1
B-18
9
A-9
B-26
2
A-2
B-19
10
A-10
B-27
3
A-3
B-20
11
A-11
B-28
4
A-4
B-21
12
A-12
B-29
5
A-5
B-22
13
A-13
B-30
6
A-6
B-23
14
A-14
B-31
7
A-7
B-24
15
A-15
B-32
Common
Publication CIG-WD001B-EN-P - May 2005
B-16 through B-33
+V dc
C-34 through C-51
(C-34 and C-51 for TB2)
1794 FLEX I/O Modules
19-19
1794-OE12
1794-TB3G, -TB3GK, -TB3GS
Channel
Signal Ty pe
Label
Ma rk in g
Output
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
Current
Voltage
I0
V0
I1
V1
I2
V2
I3
V3
I4
V4
I5
V5
I6
V6
I7
V7
I8
V8
I9
V9
I10
V10
I11
V11
A-0
A-1
A-2
A-3
A-4
A-5
A-6
A-7
A-8
A-9
A-10
A-11
A-12
A-13
A-14
A-15
B-19
B-20
B.21
B-22
B-27
B-28
B-29
B-30
(1794-TB3G shown)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Output 0
15
A
I0 V0
17
16
I1
18
19
Chassi s C0 C1
Ground
34
35
V1
I2 V2
20
I8 V8
36
37
21
22
I9
38
I3 V3
39
23
I4
24
V4 I5
25
26
V5
27
I6
28
V6
29
I7 V7
30
31
Output 1
32
33
B
Output 2
V9 C2 C3 C4 C5 I10 V10 I11 V11 C6 C7 Chassi s
Ground
Output 3
40
41
42
43
44
45
46
47
48
49
50
51
C
+V COM NC C8 Ch. C9
C10 Ch. C11 NC +V COM
24C dc
Gnd Chassis Grounds for Shields
Gnd
24C dc
Supply In
Supply Out
I = Current
V = Voltage
C0 through C11 = Returns for I or V connections 0 through 11
+24V dc = Terminals C34 and C50
COM = C35 and C51
Chassis Ground = Terminals B16, B33, C38, C40 through 45, and C47
NC = No connection
For daisy-chaining: Supply in - C34 (+) and C35 (-), Supply out - C50(+) and C51 (-)
ATTENTION
!
To reduce susceptibility to noise, power analog modules
and digital modules from separate power supplies. Do
not exceed a length of 33 ft (10m) for dc power cabling.
Do not daisy chain power or ground from this terminal
base unit to any ac or dc digital module terminal
base units.
Do not exceed a length of 33 ft (10m) for signal cabling.
Output 4
Output 5
Output 6
Output 7
Output 8
Output 9
Output 10
Output 11
-V dc
Common
+V dc
Power
Chassis
Ground
(Shield)
1794-TB3G, -TB3GK, -TB3GS
Common Te rminal
B-17
B-18
B-23
B-24
B-25
B-26
B-31
B-32
C-37
C-39
C-46
C-48
Terminals 35 and 51 are internally connected in the terminal base unit.
Terminals 34 and 50 are internally connected in the terminal base unit.
Terminals 16, 33, 38, 40 through 45, and 47 are internally connected
to chassis ground.
Publication CIG-WD001B-EN-P - May 2005
19-20
1794 FLEX I/O Modules
1794-OE4, 1794-OE4K
Output
Channel
1794-TB2, -TB3, -TB3K, -TB3S, -TB3T, -TB3TS
0
1
0
16
1
17
34
2
3
2
18
35
4
3
19
36
5
4
5
20
37
6
21
38
6
22
39
7
8
9
7
8
9
23
40
24
25
41
42
10
11 12 13 14 15
10
26
43
11
27
44
12
13
28
45
29
46
14
30
47
15
0-15
31
48
32
49
33
50
A
16-33
51
0
B
34-51
C
Terminals 35 and 50 are not used on 1794-TB2
1
TB2, TB3,
TB3K, TB3S,
TB3T, TB3TS
Output
Termi nal
TB 3T, TB 3TS
Current Signal
A-0
C-39
Current Signal
A-8
C-43
Current Common
A-11
C-39
Current Common
A-91
C-43
Signal Type
Shield
1794-TBN and -TBNK
16
16
0
34
34
1
Even Numbered Terminals 0 through 14
33
2
33
4
3
6
5
8
7
10
12
9
11
14
13
15
51
51
Odd Numbered Terminals 1 through 15
A-2
C-40
A-31
C-40
Current Signal
A-4
C-41
Current Signal
A-12
C-45
Current Common
A-51
C-41
Current Common
A-131
C-45
Voltage Signal
A-6
C-42
Voltage Common
A-71
C-42
!
3
Voltage Signal
A-10
C-44
Voltage Common
A-111
C-44
Voltage Signal
A-14
C-46
Voltage Common
A-151
C-46
+ V dc Power for TB2: C-34 and C-51
+ Vdc Power for TB3, TB3K and TB3S: C-34 through C-51
+ V dc Power for TB3T and TB3TS: C-34, 35, 50, and 51
Output
Channel
Signal
Type
Output
Terminal
Output
Channel
Signal
Type
Output
Terminal
0
Current Signal
B-0
2
Current Signal
B-8
Current Common
C-1
Current Common
C-9
Voltage Signal
B-2
Voltage Signal
B-10
Voltage Common
C-3
Current Signal
B-4
Current Common
Voltage Signal
Voltage Common
16, 0, 2, 4, 6,
B
8, 10, 12, 14, 33
34, 1, 3, 5, 7,
C
9, 11, 13, 15, 51
1
Voltage Common
C-11
Current Signal
B-12
C-5
Current Common
C-13
B-6
Voltage Signal
B-14
C-7
Voltage Common
C-15
3
+ V dc
B-16 and B-33
C34 and C-51
Only connect either a voltage signal or a current signal per channel, not both.
Connect +V to C-34.
Connect +V common to B-16.
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
Connect any signal wiring shield to functional ground as near as possible to the module when using the
1794-TB2, -TB3, -TB3K -TB3S, -TBN or -TBNK. With the 1794-TB3T and -TB3TS, use terminals C-39 through C-46.
To reduce susceptibility to noise, power analog and digital modules from
separate power supplies. Do not exceed a length of 3M (9.8 ft) for DC
power cabling.
1794-OE8H
1794-TB3G, -TB3GK, -TB3GS
0
1
2
3
4
5
+ -
+
-
ch0
ch1
6
7
8
9
10 11 12 13 14
15
Output -
Ou tput
Output +
Output -
+ -
+ -
Output 0
Ou tput
A-0
A-1
Output 4
B-17
B-18
ch2
ch3
Output 1
A-4
A-5
Output 5
B-21
B-22
Output 2
A-8
A-9
Output 6
B-25
B-26
Output 3
A-12
A-13
Output 7
B-29
B-30
Row A
16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
+ -
+
ch4
34
ch5
+ -
+ -
ch6
ch7
35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
50 51
Row C
+V -V
+V
+24V dc = Terminals C-34 and C-50
-V = C-35 and C-51
NC = No connection
For daisy-chaining: Supply in - C-34 (+) and C-35 (-)
Supply out - C-50 (+) and C-51 (-)
Publication CIG-WD001B-EN-P - May 2005
Output +
32 33
Row B
-V
Sh ie ld
Voltage Signal
A-1, 3, 5, 7, 9, 11, 13, and 15 are internally connected in the module to +V common.
Common
ATTENTION
2
TB 3T, TB 3TS
Voltage Common
Common for TB2, TB3, TB3K, TB3S: B-16 through B-33
Common for TB3T and TB3TS: B-16, 17, 19, 21, 23, 25, 27, 29, 31, and 33
1
Signal Type
Output
Channel
TB2, TB3,
TB3K, TB3S,
TB3T, TB3TS
Input
Termi nal
+V
Terminals 34 and 50
-V
Terminals 35 and 51
1794 FLEX I/O Modules
19-21
1794-OF4I
1794-TBN, -TBNK
1794-TB2, -TB3, -TB3K, -TB3S, -TB3T, -TB3TS
Even Numbered Terminals 0 through 14
16
16
0
34
2
4
1
6
3
8
5
10
7
12
9
33
14
11
13
15
51
Odd Numbered Terminals 1 through 15
34
Output
Channel
16, 0, 2, 4, 6, B
8. 10. 12. 14. 33
34, 1, 3, 5, 7, C
9, 11, 13, 15, 51
33
51
0
1794-TB2, -TB3, -TB3K, -TB3S, -TB3T, -TB3TS
1
I
R
V
R
I
R
V
R
I
R
V
R
I
R
V
R
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
I
I
+
+
Current
Output
Device
+
I
Current
Output
Device
-
-
+
A
0-15
B
16-33
C
34-51
2
34 and 51
for T B2
I
+
+
Current
Output
Device
Voltage
Output
Device
3
-
+
-
Common
ac or dc
4-Wire Output
Device
dc only
3-Wire Output
Device
Current Only
2-Wire Output
Device
dc only
3-Wire Output
Device
+V dc
Signal Type
La bel Ma rkings
Terminal
Current Output
I0
A-0
Current Return
I0 Ret
A-1
Voltage Output
V0
A-2
Voltage Return
V0 Ret
A-3
Current Output
I1
A-4
Current Return
I1 Ret
A-5
Voltage Output
V1
A-6
Voltage Return
V1 Ret
A-7
Current Output
I2
A-8
Current Return
I2 Ret
A-9
Voltage Output
V2
A-10
Voltage Return
V2 Ret
A-11
Current Output
I3
A-12
Current Return
I3 Ret
A-13
Voltage Output
V3
A-14
Voltage Return
V3 Ret
A-15
1794-TBN, -TBNK
Sh iel d (TB 3T/TB 3TS)
Termi nal
C-39
C-40
C-41
C-42
C-43
C-44
C-45
C-46
B-0
C-1
B-2
C-3
B-4
C-5
B-6
C-7
B-8
C-9
B-10
C-11
B-12
C-13
B-14
C-15
TB2, TB3, TB3K, TB3S: Terminals 16 through 33 are internally connected in the terminal base unit
TB3T, TB3TS: Terminals 16, 17, 19, 21, 23, 25, 27, 29, 31, and 33 are internally connected in the terminal base unit
TBN, TBNK: Terminals 16 and 33 are internally connected in the terminal base unit
TB2, TBN, TBNK: Terminals 34 and 51 are internally connected in the terminal base unit
TB3, TB3K, TB3S: Terminals 34 through 51 are internally connected in the terminal base unit
TB3T, TB3TS: Terminals 34, 35, 50, and 51 are internally connected in the terminal base unit
Chassis Gnd TB3T, TB3TS: Terminals 39 through 46 are internally connected to chassis gnd
Connect +V to C-34.
Connect +V common to B-16.
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
Connect any signal wiring shield to functional ground as near as possible to the module when
using the 1794-TB2, -TB3, -TB3K, -TB3S, -TBN or -TBNK. With the 1794-TB3T and -TB3TS, use terminals C-39 through C-46.
Only connect either a voltage signal or a current signal per channel, not both.
ATTENTION
To reduce susceptibility to noise, power analog and digital modules from
separate power supplies. Do not exceed a length of 3M (9.8 ft) for DC
power cabling.
!
1794-OM8
1794-TBN, -TBNK, -TBNF
16
33
Even Numbered Terminals 0 through 14
16
0
34
34
2
1
4
3
6
5
8
7
10
9
12
11
14
13
33
15
Odd Numbered Terminals 1 through 15
51
51
16, 0, 2, 4, 6, B
8. 10. 12. 14. 33
34, 1, 3, 5, 7, C
9, 11, 13, 15, 51
Connect 220V ac L2 common to B-16.
Connect 220V ac L1 to C-34.
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
Ou tput Ch an ne l
0
1
2
3
4
5
6
7
1794-TBN, -TBNK, -TBNF
Ou tpu t Termin al Common Termin al 1
B-0
C-1
B-2
C-3
B-4
C-5
B-6
C-7
B-8
C-9
B-10
C-11
B-12
C-13
B-14
C-15
B = even numbered output terminals 0 through 14, ac common terminals 16 and 33
C = power terminals C-34 and C-51, and odd numbered output common terminals 1
through 15
1. C-1, 3, 5, 7, 9, 11, 13, and 15 are internally connected in the module to 220V ac
common L2.
Publication CIG-WD001B-EN-P - May 2005
19-22
1794 FLEX I/O Modules
1794-OV16, 1794-OV16P
1794-TB3, -TB3K, -TB3S
Output
Channel
Output
Terminal
Power
Terminal
Output
Channel
Output
Terminal
Power
Terminal
0
A-0
C-35
8
A-8
C-43
1
A-1
C-36
9
A-9
C-44
2
A-2
C-37
10
A-10
C-45
3
A-3
C-38
11
A-11
C-46
4
A-4
C-39
12
A-12
C-47
5
A-5
C-40
13
A-13
C-48
6
A-6
C-41
14
A-14
C-49
7
A-7
C-42
15
A-15
C-50
1794-TB3, -TB3K, -TB3S
0
1
0
16
1
3
2
17
34
2
3
18
35
4
19
4
20
36
5
5
38
7
6
21
37
6
7
22
39
8
8
23
41
10
9
24
40
9
10
25
42
26
43
11 12 13 14 15
11
27
44
12
28
13
29
45
14
15
30
46
47
48
A
0-15
31
32
49
33
16-33
B
51
50
C
34-51
Connect +V to C-34.
Connect +V common to B-16.
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
Common
B-16 through B-33
+V dc
C-34 through C-51
1794-OW8, 1794-OW8K
1794-TBN, -TBNK, -TBNF
16
33
Even Numbered Terminals 0 through 14
16
0
2
34
4
1
6
3
5
8
10
7
9
12
11
14
13
33
15
Odd Numbered Terminals 1 through 15
34
16, 0, 2, 4, 6,
B
8. 10. 12. 14. 33
51
34, 1, 3, 5, 7,
C
9, 11, 13, 15, 51
51
16
1
17
34
2
18
35
3
19
36
4
5
20
37
21
38
6
22
39
7
23
40
8
24
41
9
25
42
10
26
43
11
27
44
12
28
45
13
29
46
0
1
2
1794-TB2, -TB3, -TB3K, -TB3, -TB3S
0
Output
Channel
14
30
47
15
31
48
0-15
32
49
33
50
51
A
B
16-33
34-51
C
Terminals 35 and 50 are not used on 1794-TB2
3
4
5
ATTENTION
!
Do not attempt to increase load current or wattage capability beyond the maximum
rating by connecting 2 or more outputs in parallel. The slightest variation in relay
switching time may cause one relay to momentarily switch the total load current.
Apply only +24V dc power to the power terminals on the terminal base unit.
Make certain that all relay wiring is properly connected before applying any
power to the module.
Total current draw through the terminal base unit is limited to 10A.
Separate power connections to the terminal base unit may be necessary.
6
7
1794-TB2, -TB3,
-TB3K, -TB3S
Output Terminal
A-0
1794-TBN,
-TBNK, -TBNF
Output Terminal
B-0
A-1
C-1
A-2
B-2
A-3
C-3
A-4
B-4
A-5
C-5
A-6
B-6
A-7
A-8
C-7
B-8
A-9
C-9
A-10
B-10
A-11
C-11
A-12
B-12
A-13
C-13
A-14
B-14
A-15
C-15
A = output terminals
B = even numbered output
B = dc common terminals
terminals 0-14, 24V dc common
C = power terminals (C-34 through
terminals 8-16 and B-33
C-51 for 1794-TB3, -TB3K -TB3S; C = odd numbered output
C-34 and C-51 for 1794-TB2)
terminals 1-15; 24V dc power
terminals C-34 and C-51
Connect +24V dc to C-34.
Connect +24V dc common to B-16.
Use B-33 and C-51 for daisy chaining to the next terminal base unit.
Publication CIG-WD001B-EN-P - May 2005
1794 FLEX I/O Modules
19-23
1794-VHSC
Connections for 1794-TB3G, -TB3GK and -TB3GS (TB3G shown)
Channel 0 Counter/Frequency Input
0
A
1
2
3
4
5
Channel 1 Counter/Frequency Input
6
7
8
9
10
11
A
A
B
B
Z
Z
O0
O1
A
A
B
B
24V Inputs
16
B
17
13
14
Incre men tal
En cod er
Inpu ts
15
18
19
Z
Z
O2
O3
24V Inputs
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Row 2
Chassis
Gnd
A
A
B
B
Z
R0
Z
A
R1
B
A
5V Inputs
34
C
12
Row 1
35
36
B
Z
Z
R2
R3
Chassis
Gnd
COM
NC
37
38
39
40
41
42
43
44
45
+V
Chassis
Gnd
-V
6 Chassis Ground
for Shields
Power for 00 to 01
46
47
48
49
50
!
+24V I npu ts
+5V Inp uts
Input A
A-0
B-17
A-8
B-25
Input A
A-1
B-18
A-9
B-26
Input B
A-2
B-19
A-10
B-27
Input B
A-3
B-20
A-11
B-28
Input Z
A-4
B-21
A-12
B-29
Input Z
A-5
B-22
A-13
B-30
+V
Chassis
Gnd
-V
NC
+24V
Output s
Sourcing
Ou t
Return
Output 0
(O0)
A-6
B-23
A-7
B-24
51
Outputs
Output 0
(O2)
Sourcing
Ou t
Return
A-14
B-31
A-15
B-32
COM
Output 1
(O1)
Power for 02 to 03
Where: A, A = incremental encoder input A (+5 or +24V dc)
B, B = incremental encoder input B (+5 or +24V dc)
Z, Z = incremental encoder input Z (+5 or +24V dc)
O = sourcing outputs
R = returns for sourcing outputs
+V = +5 or +24V dc isolated power externally supplied for outputs (1A max)
-V = negative isolated power connection (1A max)
+24V dc = 24V dc terminal base power for module
COM = return for +24V dc terminal base power for module
Chassis Gnd = chassis ground for input or output cable shields
NC = No connect
ATTENTION
Channe l 1
+5V I npu ts
5V Inputs
Row 3
+24V
Cha nnel 0
+24V In put s
Output 1
(O3)
+24V Terminal Base Power Terminals C-34 and C-50
24V COM
Terminals C-35 and C-51
+5V or +24V power
Terminals C-37 and C-46
(this isolated power is
externally supplied for
outputs with a 1A max.)
-V output power
Terminals C-39 and C-48
Chassis Ground
Terminals C-16, B-33 and C-38, C-40 through C-45, C-47
To reduce the susceptibility to noise, power analog modules and digital modules from separate power supplies. Do not exceed a length of 3m (9.8ft) for dc power cabling.
Total current draw through the terminal base unit is limited to 10A. Separate power connections to the terminal base unit may be necessary.
Publication CIG-WD001B-EN-P - May 2005
19-24
1794 FLEX I/O Modules
Notes:
Publication CIG-WD001B-EN-P - May 2005
Chapter
20
1797 FLEX Ex Modules
1797-IBN16
0
1
2
3
4
+
-
+
-
+
5
6
7
8
9
10
11
12
13
14
15
+
-
+
-
Row A
Ch 0
16
Ch 1
-
+
Ch 2
-
+
Ch 3
-
+
Ch 4
-
Ch 5
Ch 6
17
18
19
20
21
22
23
24
25
26
27
28
29
30
+
-
+
-
+
-
+
-
+
-
+
-
+
-
Ch 7
31
32
33
Row B
Ch 8
Ch 9
34
35
Ch 10
36
37
38
Ch 11
39
40
Ch 12
41
42
Ch 13
43
44
+
Ch 14
45
46
-
Ch 15
47
48
49
50
51
+V
-V
Row C
+V
-V
No connection allowed to terminals 36-39 and 46-49
1797-IE8
0
1
2
+
sig
-
3
4
5
6
7
8
9
10
11
12
13
14
+
sig
15
Row A
+ sig
Ch 0
16
-
+ sig
Ch 1
17
18
19
+
sig
-
20
21
22
-
Ch 2
23
24
25
26
-
Ch 3
27
28
29
30
31
32
33
Row B
+ sig
Ch 4
34
-
+ sig
Ch 5
35
36
37
38
39
-
+
40
41
42
43
sig
-
Ch 7
Ch 6
44
45
46
47
48
49
50
51
Row C
+V -V
+V -V
No connection allowed to terminals 3, 7, 11, 15, 20, 24, 28, 32, 36-39 and 46-49
1
Publication CIG-WD001B-EN-P - May 2005
20-2
1797 FLEX Ex Modules
1797-IE8H
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
+
sig
-
H
+
sig
-
H
+
sig
-
H
+
sig
-
H
Row A
Ch 0
16
17
18
Ch 1
19
20
Ch 2
Ch 3
21
22
23
24
25
26
27
28
29
30
31
32
33
+
sig
-
H
+
sig
-
H
+
sig
-
H
Chassis
GND
for
Shields
Row B
+
Chassis
GND
for
Shields
-
sig
H
Ch 4
34
35
+V
-V
Ch 5
36
37
38
39
Ch 6
40
41
42
43
Ch 7
44
45
46
47
48
49
50
51
Row C
+V
-V
No connection allowed to terminals 36-39 and 46-49
1797-IE8NF
0
1
2
+
sig
-
3
4
5
6
7
8
9
10
11
12
13
14
+
sig
15
Row A
+ sig
Ch 0
16
-
+ sig
Ch 1
17
18
19
+
sig
-
20
21
22
-
Ch 2
23
24
25
26
-
Ch 3
27
28
29
30
31
+
sig
32
33
Row B
+ sig
Ch 4
34
-
+ sig
Ch 5
35
36
37
38
39
-
Ch 7
Ch 6
40
41
42
43
-
44
45
46
47
48
49
50
51
Row C
+V -V
+V -V
No connection allowed to terminals 3, 7, 11, 15, 20, 24, 28, 32, 36-39 and 46-49
Publication CIG-WD001B-EN-P - May 2005
1797 FLEX Ex Modules
20-3
1797-IJ2
0
1
2
3V
6V
17
18
3
4
5
6
7
8
9
10
11
12
13
14
15
Row A
16
V+ GND 50 500/50 N 8V
mV mV
Sel
Channel 0 Frequency Input
19
20
21
22
23
8V N 500/50 50 GND V+ 6V 3V
mV mV
Sel
Channel 1 Frequency Input
24
25
26
27
28
29
30
8V
8V N 500/50 50 GND
mV mV
Sel
31
32
33
Row B
GND 50 500/50 N
mV mV
Sel
R0 NO R0 NC
Channel 0 Gate Input
Row C
34
35
+V
-V
36
37
38
R1 NO R1 NC
Channel 1 Gate Input
39
40
41
42
43
44
45
R0 COM
46
47
48
49
R1 COM
50
+V
51
-V
No connection allowed to terminals 19, 30, 36, 38, 39, 47, 48, 49
1797-IRT8
0
1
2
+
H
L
3
4
5
6
7
8
9
10
11
12
13
14
15
Row A
-
+
H
Ch 0
16
L
-
+
H
Ch 1
17
18
19
20
21
+
H
L
-
+
L
-
+
H
Ch 2
22
23
24
L
-
Ch 3
25
26
27
+
H
L
28
29
30
+
H
31
32
33
Row B
H
Ch 4
L
-
Ch 5
34
35
+V
-V
36
37
38
-
Ch 6
39
40
41
42
L
-
Ch 7
43
44
45
46
47
48
49
50
51
Row C
CJC
CJC
0+ chassis 01+ chassis 1GND for
GND for
shield
shield
No connection allowed to terminals 36 and 49
+V
-V
1797-OB4D
0
1
2
3
4
5
+
-
6
7
8
9
+
-
10
11
12
13
14
15
Row A
+
ch0
16
17
ch1
18
19
20
21
+
ch2
22
23
24
25
-
ch3
26
27
28
29
30
31
32
33
Row B
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Row C
+V
-V
+V -V
No connections allowed to terminals 2, 3, 6, 7, 10, 11, 14, 15, 17 to 32, 36, 37, 38, 39, 46, 47, 48, 49
Publication CIG-WD001B-EN-P - May 2005
20-4
1797 FLEX Ex Modules
1797-OE8
0
1
2
3
4
5
+
-
6
7
8
9
10
11
12
13
14
15
Row A
+
-
ch0
16
+
ch1
17
18
19
20
-
+
ch2
21
22
23
24
25
-
ch3
26
27
28
29
30
31
32
33
Row B
+
-
+
ch4
-
+
ch5
34
35
36
+V
-V
37
-
+
38
39
40
41
42
-
ch7
ch6
43
44
45
46
47
48
49
50
51
Row C
+V
No connections allowed to terminals 2, 3, 6, 7, 10, 11, 14, 15, 19, 20, 23,
24, 27, 28, 31, 32, 36, 37, 38, 39, 46, 47, 48, 49
-V
1797-OE8H
0
1
2
3
4
5
+
-
6
7
8
9
+
-
10
11
12
13
+
-
14
15
Row A
-
+
Ch 0
16
17
Ch 1
18
19
20
Ch 2
21
22
23
+
-
24
Ch 3
25
26
27
+
-
28
29
30
+
-
31
32
33
Row B
Chassis
GND
+
-
Ch 4
Ch 5
34
35
+V
-V
36
37
38
Ch 6
39
40
41
42
Chassis
GND
Ch 7
43
44
45
46
47
48
49
50
51
Row C
+V
No connection allowed to terminals 2, 3, 6, 7, 10, 11,
14, 15, 19, 20, 23, 24, 27, 28, 31, 32, 36-39 and 46-49
Publication CIG-WD001B-EN-P - May 2005
-V
Chapter
21
1798 FLEX Armor I/O Modules
1798-DFTP1
1798-DFTP2
3
4
5
2
Male M12 Micro Connector (In)
(View into Socket)
1
4
5
2
Female M12 Micro Connector
(Daisy Chain Out)
3
3
4
2
The connection to the
power connector
should be a 4-pin
female mini quick
disconnect connector.
Pin 1 Output Power +
Pin 2 Sensor Power + (Red wire)
Pin 3 Sensor Power Pin 4 Output Power -
1798-IB4, -IB4D and -IB8
Female Input Micro- Connector
(View into Socket)
Pin 1 Sensor Power
Pin 2 Input B (IB8 Modules Only)
Pin 3 Sensor Common
Pin 4 Input A
Pin 5 Not Used
1798-OB4E and -OB8E
Female Output Micro Connector
(View into Socket)
Pin 1 Not Used
Pin 2 Output B (OB8E modules only)
Pin 3 Output Common
Pin 4 Output A
Pin 5 Not Used
1
Male M18 Mini Connector (In)
(View into Socket)
3
5
4
Pin 1 Drain Wire
Pin 2 +Voltage
Pin 3 -Voltage
Pin 4 Controller Area Network (CAN) High
Pin 5 Controller Area Network (CAN) Low
5
4
Female M18 Mini Connector
(Daisy Chain Out)
3
1
2
Male Power Connector
1
2
Pin 1 Drain Wire
Pin 2 +Voltage
Pin 3 -Voltage
Pin 4 Controller Area Network (CAN) High
Pin 5 Controller Area Network (CAN) Low
1
1
3
4
Male Power Connector
1
2
Pin 1 Output Power +
Pin 2 Sensor Power +
Pin 3 Sensor Power Pin 4 Output Power -
1798-IE4
Female Input Micro-Connector
(View into Socket)
Pin 1 Sensor Power
Pin 2 Current Input
Pin 3 Sensor Common
Pin 4 Voltage Input
Pin 5 Not Used
1798-OE2
Female Input Micro- Connector
(View into Socket)
Pin 1 Sensor Power
Pin 2 Current Output
Pin 3 Sensor Common
Pin 4 Voltage Output
Pin 5 Not Used
Publication CIG-WD001B-EN-P - May 2005
21-2
1798 FLEX Armor I/O Modules
1798-PFTP1
3
4
5
2
Pin 1 +5V BUS
Pin 2 A-Line
Pin 3 GNDBUS
Pin 4 B-Line
Pin 5 Shield
1
1
4
5
3
Publication CIG-WD001B-EN-P - May 2005
Male M12 Connector
(PBUS IN)
2
Female M12 Connector
(PBUS OUT)
Power Connector
(Male Connector)
1
5
4
2
3
Pin 1 Output Power Pin 2 Sensor Power Pin 3 Protective Gnd
Pin 4 Sensor Power +
Pin 5 Output Power +
The connection to the
power connector
should be a 5-pin
female mini quick
disconnect connector.
Chapter
22
1799 Embedded I/O Cards
1799-D10U10B, 1799-D10U10BL, 1799-D10U10BZC, 1799-ZCIOB
Outputs Sourcing
0
2 24V dc 3
Return
1
6 24V dc 7
5
4
1799-D10U10V, 1799-D10U10VL, 1799-D10U10VZC, 1799-ZCIOV
Outputs Sinking
9
8
0
2 24V dc 3
Return
1
4
6 24V dc 7
5
8
9
Load
Load
1799-D10U10B, 1799-D10U10BL, 1799-D10U10BZC, 1799-ZCIOB, 1799-D10U10V, 1799-D10U10VL, 1799-D10U10VZC, 1799-ZCIOV
Inputs Sourcing
0
1
1
2
In
3
Common
4
5
6
Inputs Sinking
In
7
Common
8
0
9
+
+
_
_
1
2
In
3
Common
4
5
6
In
7
Common
8
9
Publication CIG-WD001B-EN-P - May 2005
22-2
1799 Embedded I/O Cards
Notes:
Publication CIG-WD001B-EN-P - May 2005
Rockwell Automation
Support
Rockwell Automation provides technical information on the web to assist you in using
our products. At http://support.rockwellautomation.com, you can find technical
manuals, a knowledge base of FAQs, technical and application notes, sample code and
links to software service packs, and a MySupport feature that you can customize to
make the best use of these tools.
For an additional level of technical phone support for installation, configuration and
troubleshooting, we offer TechConnect Support programs. For more information,
contact your local distributor or Rockwell Automation representative, or visit
http://support.rockwellautomation.com.
Installation Assistance
If you experience a problem with a hardware module within the first 24 hours of
installation, please review the information that's contained in this manual. You can also
contact a special Customer Support number for initial help in getting your module up
and running:
United States
1.440.646.3223
Monday – Friday, 8am – 5pm EST
Outside United
States
Please contact your local Rockwell Automation representative for any
technical support issues.
New Product Satisfaction Return
Rockwell tests all of our products to ensure that they are fully operational when
shipped from the manufacturing facility. However, if your product is not functioning
and needs to be returned:
United States
Contact your distributor. You must provide a Customer Support case
number (see phone number above to obtain one) to your distributor in
order to complete the return process.
Outside United
States
Please contact your local Rockwell Automation representative for
return procedure.
Publication CIG-WD001B-EN-P – May 2005 2
Supersedes Publication CIG-WD001A-EN-P – October 2003
Copyright © 2005 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.