Download Samsung SAMTRON 78BDF Service manual

COLOR MONITOR
PN17KT/KO
PN17JT/JO
SERVICE
Manual
COLOR MONITOR
CONTENTS
1. Precautions
2. Product Specifications
3. Disassembly & Reassembly
4. Alignment & Adjustments
5. Troubleshooting
6. Exploded View & Parts List
PN17KT/JT
7. Electrical Parts List
8. Block Diagram
9. Wiring Diagram
10. Schematic Diagrams
PN17KO/JO
Samsung Electronics Co.,Ltd.
416, Maetan-3Dong, Paldal-Gu, Suwon City, Kyungki-Do, Korea.
Tel : +82-31-200-7920 Fax : +82-31-200-7802
Printed in Korea
P/N : BH68-00393J-00
http://www.samsungmonitor.com (SyncMaster Worldwide)
http://www.samsung-monitor.com (SyncMaster USA)
http://www.samtron.com (SAMTRON Worldwide)
http://www.sec.co.kr/monitor (Korea)
1 Precautions
1-1 Safety Precautions
WARNINGS
1. For continued safety, do not attempt to modify the
circuit board.
2.
Disconnect the AC power before servicing.
3.
When the chassis is operating, semiconductor
heatsinks are potential shock hazards.
1-1-1
1.
When servicing the high voltage system, remove
the static charge by connecting a 10 kohm resistor
in series with an insulated wire (such as a test
probe) between the chassis and the anode lead.
2.
When troubleshooting a monitor with excessively
HV, avoid being unnecessarily close to the monitor.
Do not operate the monitor for longer than is
necessary to locate the cause of excessive voltage.
3.
High voltage should always be kept at the rated
value, no higher. Only when high voltage is
excessive are X-rays capable of penetrating the shell
of the CRT, including the lead in glass material.
Operation at high voltages may also cause failure of
the CRT or high voltage circuitry.
5.
When the HV regulator is operating properly, there
is no possibility of an X-ray problem. Make sure the
HV does not exceed its specified value and that it is
regulating correctly.
The CRT is especially designed to prohibit
X-ray emissions. To ensure continued X-ray
protection, replace the CRT only with one that is
the same or equivalent type as the original.
6.
Handle the CRT only when wearing shatterproof
goggles and after completely discharging the high
voltage anode.
7.
Do not lift the CRT by the neck.
1-1-2
Leakage Current Hot Check (Figure 1-1):
WARNING: Do not use an isolation transformer during
this test.
Use a leakage current tester or a metering system
that complies with American National Standards
Institute (ANSI C101.1, Leakage Current for
Appliances), and Underwriters Laboratories (UL
Publication UL1410, 59.7).
4.
With the unit completely reassembled, plug the AC
line cord directly into a 120V AC outlet. With the
unit’s AC switch first in the ON position and then
OFF, measure the current between a known earth
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including: metal cabinets,
screwheads and control shafts. The current
measured should not exceed 0.5 milliamp. Reverse
the power-plug prongs in the AC outlet and repeat
the test.
Servicing the High Voltage and CRT :
WARNING:A high voltage adjusted to the wrong
value may cause excessive X-ray
emissions.
4.
3.
Fire and Shock Hazard :
Before returning the monitor to the user, perform the
following safety checks:
1.
Inspect each lead dress to make certain that the
leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in
the monitor.
2.
Inspect all protective devices such as nonmetallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.
PN17K*/PN17J*
(READING SHOULD
NOT BE ABOVE 0.5mA)
LEAKAGE
CURRENT
TESTER
DEVICE
UNDER
TEST
TEST ALL
EXPOSED METAL
SURFACES
2-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
EARTH
GROUND
Figure 1-1. Leakage Current Test Circuit
1-1-3 Product Safety Notices
Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection. The protection they give
may not be obtained by replacing them with
components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified by
! on schematics and parts lists. A substitute
replacement that does not have the same safety
characteristics as the recommended replacement part
might create shock, fire and / or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.
Components identified by
on schematics and parts
lists must be sealed by a soldering iron after
replacement and adjustment.
1-1
1 Precautions
1-2 Servicing Precautions
WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances
create conflict between the servicing precautions and safety precautions, always follow
the safety precautions.
WARNING2: A high voltage adjusted to the wrong value may cause excessive X-ray emissions.
WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.
1.
Servicing precautions are printed on the cabinet,
and should be followed closely.
2.
Always unplug the unit’s AC power cord from the
AC power source before attempting to: (a) remove
or reinstall any component or assembly, (b)
disconnect PCB plugs or connectors, (c) connect all
test components in parallel with an electrolytic
capacitor.
3.
4.
Some components are raised above the printed
circuit board for safety. An insulation tube or tape
is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.
After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the area around the
serviced part has not been damaged.
5.
Check the insulation between the blades of the AC
plug and accessible conductive parts (examples:
metal panels, input terminals and earphone jacks).
6.
Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the power
switch ON. Connect an insulation resistance meter
(500 V) to the blades of the AC plug.
The insulation resistance between each blade of the
AC plug and accessible conductive parts (see
above) should be greater than 1 megohm.
7.
Never defeat any of the +B voltage interlocks. Do
not apply AC power to the unit (or any of its
assemblies) unless all solid-state heat sinks are
correctly installed.
8.
Always connect a test instrument’s ground lead to
the instrument chassis ground before connecting the
positive lead; always remove the instrument’s
ground lead last.
1-3 Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some fieldeffect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.
1.
Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wriststrap device. To avoid a shock hazard, be sure to
remove the wrist strap before applying power to
the monitor.
6.
Do not remove a replacement ESD from its
protective package until you are ready to install it.
Most replacement ESDs are packaged with leads
that are electrically shorted together by conductive
foam, aluminum foil or other conductive materials.
7.
2.
After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of an electrostatic charge.
Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.
3.
Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESDs.
Caution: Be sure no power is applied to the
chassis or circuit and observe all
other safety precautions.
4.
Use only a grounded-tip soldering iron to solder or
desolder ESDs.
5.
Use only an anti-static solder removal device. Some
solder removal devices not classified as “anti-static”
can generate electrical charges sufficient to damage
ESDs.
1-2
8.
Minimize body motions when handling
unpackaged replacement ESDs. Motions such as
brushing clothes together, or lifting your foot from
a carpeted floor can generate enough static
electricity to damage an ESD.
9.
Indicates ESDs on the Schematic Diagram in
this manual.
PN17K*/PN17J*
2 Product Specifications
2-1 Specifications
Description
Item
PN17K*
PN17J*
Picture Tube:
17-Inch (43 cm): 16-inch (40.6 cm) viewable,
Perfect Flatness, 90˚ Deflection, Semi- tint, Invar shadow mask,
Anti-static silica coating, 0.26 mm Dot pitch
Scanning Frequency Horizontal
Vertical
30 kHz ~ 70 kHz (Automatic)
50 Hz ~ 160 Hz (Automatic)
Display Colors
Unlimited colors
Maximum Resolution Horizontal
Vertical
1280 Dots
1024 Lines
Input Video Signal
Analog, 0.7 Vp-p positive at 75 Ω, internally terminated
Input Sync Signal
Separate Sync : TTL level positive/negative
Maximum Pixel Clock rate
110 MHz
Active Display (Horizontal/Vertical)
312 mm ± 4 mm / 234 mm ± 4 mm
Input Voltage
AC 90 ~ 264 Volts, 60 Hz / 50 Hz ± 3 Hz
Power Consumption
90 Watt (max)
Dimensions (W x D x H)
(with Base)
15.67 x 16.22 x 15.75 Inches (398 x 412 x 400 mm)
Weight
41.22 lbs (18.7 kg)
Environmental Considerations
Operating Temperature : 32°F ~ 104°F (0°C ~ 40°C)
Humidity : 10 % ~ 80 %
Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C)
Humidity : 5 % ~ 95 %
30 kHz ~ 85 kHz (Automatic)
50 Hz ~ 160 Hz (Automatic)
1600 Dots
1200 Dots
135 MHz
100 Watt (max)
• Above models comply with SWEDAC MPR II / TCO99 recommendations for reduced electromagnetic fields.
• Designs and specifications are subject to change without prior notice.
PN17K*/PN17J*
2-1
2 Product Specifications
2-2 Pin Assignments
Sync
Type
Separate
Macintosh
Pin No.
1
Red
GND-R
2
Green
Red
3
Blue
H/V Sync.
4
N-C
Sense 0
5
GND (DDC)
Green
6
GND-R
GND-G
7
GND-G
Sense 1
8
GND-B
Reserved
9
N-C
Blue
10
GND-Sync./Self-raster
Sense 2
11
N-C
GND
12
DDC Data
V-Sync.
13
H-Sync.
GND-B
14
V-Sync.
GND
15
DDC Clock
H-Sync.
1
6
2
7
5
3
10
8
12
13
14
15
Figure 2-1. Male Type
2-2
Figure 2-2. Male Type
PN17K*/PN17J*
2 Product Specifications
2-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard
for computer-generated video signals.
Table 2-1. Timing Chart
Mode
IBM
VESA
640/75 Hz
VGA2/70 Hz VGA3/60 Hz
640 x 480
720 x 400 640 x 480
Timing
(PN17K*)
640/85 Hz
640 x 480
800/75 Hz 800/85 Hz 1024/75 Hz 1024/85 Hz 1280/75 Hz
1280 x 1024
800 x 600 800 x 600 1024 x 768 1024 x 768
(PN17J*)
fH (kHz)
31.469
31.469
37.500
43.269
46.875
53.674
60.023
68.677
79.976
A µsec
31.777
31.778
26.667
23.111
21.333
18.631
16.660
14.561
12.504
B µsec
3.813
3.813
2.032
1.556
1.616
1.138
1.219
1.016
1.067
C µsec
1.907
1.907
3.810
2.222
3.232
2.702
2.235
2.201
1.837
D µsec
25.422
25.422
20.317
17.778
16.162
14.222
13.003
10.836
9.481
E µsec
0.636
0.636
0.508
1.556
0.323
0.569
0.203
0.508
0.119
fV (Hz)
70.087
59.940
75.000
85.008
75.000
85.061
75.029
84.997
75.025
O msec
14.268
16.683
13.333
11.764
13.333
11.756
13.328
11.765
13.329
P msec
0.064
0.064
0.080
0.671
0.064
0.056
0.050
0.044
0.038
Q msec
1.080
1.048
0.427
0.578
0.448
0.503
0.466
0.524
0.475
R msec
12.711
15.253
12.800
11.093
12.800
11.179
12.795
11.183
12.804
S msec
0.413
0.318
0.027
0.023
0.021
0.019
0.017
0.015
0.013
28.322
25.175
31.500
36.000
49.500
56.250
78.750
94.500
135.000
Polarity
H.Sync
Negative
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Positive
V.Sync
Positive
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Remark
Separate
Separate
Separate
Separate
Separate
Separate
Separate
Separate
Separate
Clock
Frequency
(MHz)
Separate Sync
Horizontal
Vertical
Video
Video
Video
Video
CC
DD
E
E
Q
RR
Q
S S
Sync
Sync
Sync
Sync
BB
PP
AA
O O
A : Line time total
B : Horizontal sync width
O : Frame time total
P : Vertical sync width
C : Back porch
D : Active time
Q : Back porch
R : Active time
E : Front porch
PN17K*/PN17J*
S : Front porch
2-3
2 Product Specifications
Memo
2-4
PN17K*/PN17J*
3 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the
PN17K*/PN17J* monitors.
WARNING: This monitor contains electrostatically sensitive devices. Use with caution when
handling these components.
3-1 Disassembly
Cautions:1. Disconnect the monitor from the power source before disassembly.
2. To remove the Rear Cover, you must use the special opening jig tool.
3-1-1 Before making Disassembly
1. Disconnect the power cord from the monitor.
2. With a pad beneath it, stand the monitor on its
front with the screen facing downward and
the base close to you.
4. Push the Opening jig each groove along the
top of the monitor till it makes a “ttak” sound.
(2 grooves : Left and Right, Make sure each
snap is disengaged.)
3-1-2 Cabinet Disassembly
1. Remove the Stand from the monitor.
(Refer to Stand manual)
2. Remove 2 screws on the Rear cover.
Figure 3
5. Pull the Rear Cover up off the monitor.
Figure 1
3. Incline the monitor by lifting the rear of the
monitor.
Figure 4
6. Remove the Shield.(TCO 99)
Figure 2
Figure 5
PN17K*/PN17J*
3-1
3 Disassembly and Reassembly
7. Using pinch-nose pliers or ling-nose pliers,
acrefully disconnect the Anode Cap from the
CRT.
Warning:
Do not touch the Anode contact
on the CRT (High Voltage may
remain).
3-1-3 Removing the CRT Socket PCB
1. Complete all previous steps.
2. Lift up the Video Spring and remove the CRT
Socket PCB from the CRT.
Figure 7
6. Disconnect the Tilt connector at the
CN2(CN22) connector on the Main PCB.
7. Disconnect the Sub PCB connector at the
CN201 connector on the Main PCB.
8. Remove the screws on the back and along
each side of the Bottom Chassis.
9. Carefully lift the Main PCB Ass’y and remove
the remaining ground wires.
10. Place the Main PCB Ass’y on a flat, level
surface that is protected from static electricity.
Figure 6
3. Disconnect all connectors on the CRT Socket
PCB.
4. Using a solder iron, disconnect Ground (GND)
on the back of the Video Shield and remove
the Shield Cap.
5. Remove the screw on the front of the Shield
Socket.
6. Desolder the 4 tabs on the CRT Socket PCB
and remove Shield.
7. Place the Video PCB on a flat, level surface
that is protected from static electricity.
3-1-4 Removing the Main PCB
3-1-5 CRT Ass’y Disassembly
1. Complete all previous steps.
2. Straighten the Degaussing Coil Assembly
coated metal ties and lift the Coil Ass’y from
the CRT.
3. Remove the four corner screws and lift the
CRT up and away from the Front Cover
Assembly and place it on a padded surface.
Caution: Do not lift the CRT by the neck.
If you will be returning this CRT to
the monitor, be sure to place the CRT
face downward on a protective pad.
1. Complete all previous steps.
2. Disconnect the Degaussing Coil at GT601 and
CN603 on the Main PCB.
3. Disconnect all easily accessible ground wires
on the PCB and Bottom Chassis.
4. Disconnect the DY connector at the CN401
connector on the Main .
5. Using the jig, release the snaps (2) connecting
the Front Cover and the PCB then lift up the
Bottom to separate the two Shield.
3-2 Reassembly
Reassembly procedures are in the reverse order of Disassembly procedures.
3-2
PN17K*/PN17J*
4 Alignment and Adjustments
This section of the service manual explains how to make permanent adjustments to the monitor. Directions
are given for adjustments using the monitor Interface Board Ver. 2.0 and software (Softjig).
4-1 Adjustment Conditions
Caution:Changes made without the Softjig are saved only to the user mode settings. As such, the
settings are not permanently stored and may be inadvertently deleted by the user.
4-1-1 Before Making Adjustments
4-1-2 Required Equipment
4-1-1 (a) ORIENTATION
When servicing, always face the monitor to the
east.
The following equipment may be necessary for
adjustment procedures:
4-1-1 (b) MAGNETIC FIELDS
Whenever possible, use magnetic field isolation
equipment such as a Helmholtz field to surround
the monitor. If a Helmholtz field is not available,
frequently degauss the unit under test.
Caution: Other electrical equipment may
cause external magnetic fields
which may interfere with monitor
performance.
Use an external degaussing coil to limit magnetic
build up on the monitor. If an external degaussing
coil is not available, use the internal degaussing
circuit. However, do not use the internal
degaussing circuit more than once per 30 minutes.
4-1-1 (c) WARM-UP TIME
The monitor must be on for 30 minutes before
starting alignment. Warm-up time is especially
critical in color temperature and white balance
adjustments.
4-1-1 (d) SIGNAL
Analog, 0.7 Vp-p positive at 75 ohm, internal
termination
Sync: TTL level, negative/positive
4-1-1 (e) SCANNING FREQUENCY
4-1-2 (a) DISPLAY CONTROL ADJUSTMENT
1. Non-metallic (–) screwdriver:
1.5, 2.5, 3 mm
2. Non-metallic (+) screwdriver:
1.5, 2.5, 3 mm
3. Digital Multimeter (DMM), or
Digital Voltmeter
4. Signal generator, or
DM200 software
5. Software: Softjig or DM200
6. Interface Board Ver. 2.0 Code No.
BH81-90001K
7. Parallel communications cable (25-pin to
25-pin); Code No. BH81-90001H
8. Signal cable (15-pin to 15-pin cable with
additional 3-pin connector); Code No.
BH81-90001J
9. 5 V DC adapter, not supplied
10. Personal computer
Note: Softjig Ass’y (includes items 6, 7 and 9)
Code No. BH81-90001L
4-1-2 (b) COLOR ADJUSTMENTS
1. All equipment listed in 4-1-2 (a), above
2. Color analyzer, or any luminance
measurement equipment
Horizontal: PN17K* : 30 kHz ~ 70 kHz (Automatic)
PN17J* : 30 kHz ~ 85 kHz (Automatic)
Vertical:
50 Hz ~ 160 Hz (Automatic)
Unless otherwise specified, adjust at the
1024 x 768 mode (68 kHz/85 Hz) signal.
PN17K*/PN17J*
4-1
4 Alignment and Adjustments
4-1-3 Connecting the SoftJig
Connect the monitor to the signal generator and/
or PC as illustrated in Figures 4-1 and 4-2.
Note: The signal cable connector which includes
the 3-wire cable must connect to the
monitor. If you use Setup 2 (PC only, no
signal generator) you can only make
adjustments to the signal timing available
on that computer system. To make
corrections to all factory timings requires
the use of an additional signal generator.
MONITOR
INTERFACE
BOARD VER. 2.0
5V DC
ADAPTOR
SIGNAL CABLE
3-WIRE
CABLE
PARALLEL CABLE
SIGNAL
GENERATOR
PC
Figure 4-1. Setup 1, With Signal Generator
MONITOR
INTERFACE
BOARD VER. 2.0
3-WIRE CABLE
5V DC
ADAPTOR
SIGNAL CABLE
PARALLEL CABLE
PC
D-SUB
CONNECTOR
Figure 4-2. Setup 2, Without Signal Generator
4-2
PN17K*/PN17J*
4 Alignment and Adjustments
4-2 Display Control Adjustments
4-2-1 HIGH VOLTAGE ADJUSTMENT
Signal:
Display image:
Contrast:
Brightness:
Limit:
1024 x 768 (68 kHz/85 Hz)
Don’t care
Manimum
Manimum
26.0 kV ± 0.5 kV
Measure the hight voltage level at the anode cap.
High voltage should be within the limit as above.
If the high voltage needs adjustment use the
following procedure.
PROCEDURE
1. Turn the power off and disconnect the AC line
cord from the power source.
2. Turn the power on after connecting high
voltage Probe.
3. Using the jig, adjust the high voltage to the
specification.
* High Voltage Adjustment PROCEDURE using Softjig
① Select matching model name in “Model” field.
➁ Select “ @7: Zero Beam” in menu after
selecting “Extra 1”
➂ Adjust high voltage using control bar after
selecting “HV VOL”
➃ Turn the power off/on after adjustment
finished.
➄ Check the high voltage has been fixed with
adjusted value after reselecting “@7: Zero Beam”.
4-2-2 SCREEN VOLTAGE CHECK
CONDITIONS
Signal:
1024 x 768 (68 kHz/85 Hz)
Display image:
Contrast:
Brightness:
Limit:
Don’t care
Manimum
Manimum
520 V ± 10 V
Measure the Screen voltage (G2 voltage) at the pin
(CN501) on the Main PCB.
PROCEDURE
1. Connect the high voltage probe to the CN501.
(Main PCB)
2. Using the jig, adjust the G2 voltage to the
specification.
* G2 Voltage (Screen voltage) Adjustment PROCEDURE
using Softjig
① Select matching model name in “Model” field.
➁ Select “ @7: Zero Beam” in menu after
selecting “Extra 1”
➂ Adjust G2 using control bar after selecting “G2
CONT”
PN17K*/PN17J*
4-2-3 CENTER RASTER
Adjust SW401 so that the back raster comes to the
center when you apply each basic mode.
4-2-4 Centering
Centering means to position the center point of
the display in the middle of the display area.
Horizontal size and position and vertical size and
position control the centering of the display.
Adjust the horizontal size and vertical size to their
optimal settings: 312 mm (H) x 234 mm.
Adjust the horizontal position and vertical
position to ≤ 4.0 mm of the center point of the
screen.
|A-B| ≤ 4.0 mm
|C-D| ≤ 4.0 mm
C
DISPLAY AREA
A
B
EDGE OF BEZEL
D
Figure 4-3. Centering
4-2-4 (a) HORIZONTAL SIZE ADJUSTMENT
CONDITIONS
Scanning frequency:
Display image:
Brightness:
Contrast:
68 kHz/85 Hz
Crosshatch pattern
Maximum
Maximum
Use control bar after selecting “SIZE B+” in left
menu to adjust the horizontal size of the display
pattern to 312 mm with OSD “H-SIZE” fixed “39”.
(Tolerance: ± 4 mm.)
Specially run “All mode save” after horizontal
size adjustment in order to save “SIZE B+” values
of other modes automatically.
4-2-4 (b) VERTICAL SIZE ADJUSTMENT
CONDITIONS
Scanning frequency:
Display image:
Brightness:
Contrast:
68 kHz/85 Hz
Crosshatch pattern
Maximum
Maximum
Use control bar after selecting “V-SIZE” in left
menu to adjust the vertical size of the display
pattern to 234 mm. (Tolerance: ± 3 mm.)
4-3
4 Alignment and Adjustments
4-2-4 (c) HORIZONTAL POSITION ADJUSTMENT
CONDITIONS
Scanning frequency:
Display image:
68 kHz/85 Hz
Crosshatch pattern
Use control bar after selecting “H-POSITION” in
left menu to center the horizontal image on the
raster.
4-2-4 (d) VERTICAL POSITION ADJUSTMENT
CONDITIONS
Scanning frequency:
Display image:
68 kHz/85 Hz
Crosshatch pattern
Use control bar after selecting “V-POSITION” in
left menu to center the vertical image on the
raster.
4-2-5 Linearity
Linearity affects the symmetry of images as they
appear on the screen. Unless each row or column
of blocks in a crosshatch pattern is of equal size,
or within the tolerances shown in Table 4-2 , an
image appears distorted, elongated or squashed.
Horizontal Linearity = 2x
4-2-5 (a) HORIZONTAL LINEARITY ADJUSTMENT
CONDITIONS
Scanning frequency:
68 kHz/85 Hz
Display image:
Crosshatch pattern
Brightness:
Maximum
Contrast:
Maximum
To adjust the Horizontal Linearity, refer to Table
4-1 for the tolerance range.
Increase or decrease H_LIN to optimize the
image.
4-2-5 (b) VERTICAL LINEARITY ADJUSTMENT
CONDITIONS
Scanning frequency:
68 kHz/85 Hz
Display image:
Crosshatch pattern
Brightness:
Maximum
Contrast:
Maximum
To adjust the Vertical Linearity, refer to Table 4-1
for the tolerance range.
Use control bar after selecting “V-LINEARITY
BAL” in left menu to optimize the image.
X max-X min
x100
X max+X min
Y max-Y min
Vertical Linearity = 2x
x100
Y max+Y min
Table 4-1
Adjacent Linearity Entire Linearity
Preset mode
≤ 4%
≤ 8%
Pre-load mode (48kHz~)
≤ 5%
≤ 10%
Pre-load mode (under 48kHz)
≤ 5%
≤ 14%
❈ Preset Mode : 68KHz / 85Hz
Pre-load Mode : Refer to Timing Chart
4-4
PN17K*/PN17J*
4 Alignment and Adjustments
4-2-6 Trapezoid Adjustment
4-2-9 Side Pincushion Adjustment
CONDITIONS
Scanning frequency:
Display image:
Brightness:
Contrast:
CONDITIONS
Scanning frequency:
Display image:
68 kHz/85 Hz
Crosshatch pattern
Maximum
Maximum
Use control bar after selecting “TRAPEZOID” in
left menu to make the image area rectangular.
Use control bar after selecting “PINCUSHION” in
left menu to straighten the sides of the image area.
| C1 |, | C2 | ≤ 2.0 mm, | D1 |, | D2 | ≤ 2.0 mm.
| A - B | < 4 mm
A
68 kHz/85 Hz
Crosshatch pattern
C2
A
D1
B
D2
B
Figure 4-4. Trapezoid
C1
4-2-7 Pinbalance Adjustment
CONDITIONS
Scanning frequency:
Display image:
Brightness:
Contrast:
Figure 4-7. Pincushion
4-2-10 Tilt Adjustment
68 kHz/85 Hz
Crosshatch pattern
Maximum
Maximum
CONDITIONS
Scanning Frequency:
Display image:
Brightness:
Contrast:
| D1 |, | D2 | ≤ 2.0 mm
D1
D2
D1
Figure 4-5. Pinbalance
68 kHz/85 Hz
Crosshatch pattern
Maximum
Maximum
Use control bar after selecting “ROTATION” in
left menu to correct the tilt of the display.
4-2-11 Degauss
Use control bar after selecting “PINBALANCE” in
left menu to optimize the image.
No adjustments are available for the degaussing
circuit. The degaussing circuit can effectively
function only once per 30 minutes.
4-2-8 Parallelogram Adjustment
4-2-12 To Delete the User Mode Data
CONDITIONS
Scanning Frequency:
Display image:
Brightness:
Contrast:
To delete the adjustment data from the user
modes, click “@4: USER DELETE” in right ment.
68 kHz/85 Hz
Crosshatch pattern
Maximum
Maximum
Use control bar after selecting “PARALLEL” in
left menu to make the image area rectangular.
4-2-13 Save the Data
To save the adjustment data for a mode, press
“@3: ALL MODE SAVE” in right ment.
4 mm
Figure 4-6. Parallelogram
PN17K*/PN17J*
4-5
4 Alignment and Adjustments
4-3 Color Adjustments
CAUTION: Check below condition before color
adjustment Video signal : Analog 0.7
Vp-p (at 75 )
Sync : TTL level (H, V seperate signal)
4-3-2 (b) R.G.B - GAIN ADJUSTMENT
1/3H-1/2H
FRONT BEZEL OPENING
* Select “Color” in Softjig menu for color adjustment.
BACK RASTER
1/3V-1/2V
4-3-1 Color Coordinates (Temperature)
WHITE WINDOW
Color temperature is a measurement of the
radiant energy transmitted by a color. For
computer monitors, the color temperature refers
to the radiant energy transmitted by white. Color
coordinates are the X and Y coordinates on the
chromaticity diagram of wavelengths for the
visible spectrum.
CONDITIONS
Scanning frequency:
Display image:
Brightness:
CONDITIONS
Measurement instrument: Color analyzer
Scanning frequency: 68 kHz/85 Hz
Display image:
White flat field at
center of display area
Luminance:
Maximum
4-3-2 (c) WHITE BALANCE ADJUSTMENT
PROCEDURE
Use the directions in sections 4-3-2 through 4-3-3
to adjust the color coordinates for:
9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02
6500K to x = 0.313 ± 0.02, y = 0.329 ± 0.02
4-3-2 Color Adjustments for 9300K
Figure 4-8. White Box Pattern
68 kHz/85 Hz
White box pattern
0.06ft-L at Back Raster
Pattern Display
Contrast:
Maximum
1. Click on the << or >> box next to R,G,B
_GAIN to adjust the brightness of the Green
Gain to 40 ± 1 ft-L.
9300K to x = 0.283 ± 0.02 y = 0.298 ± 0.02
CONDITIONS
Scanning frequency:
Display image:
Brightness:
Contrast:
Figure 4-9. Full White Pattern
4-3-2 (a) BACK RASTER COLOR ADJUSTMENT
CONDITIONS
Scanning frequency:
Display image:
Brightness:
Contrast:
FRONT BEZEL OPENING
BACK RASTER
68 kHz/85 Hz
Back raster pattern
Maximum
Maximum
1. Select “@1: CHANNEL 1” in right menu to
control the color for 9300K.
2. Adjust the luminance of the back raster to
between 0.5 to 0.7 ft-L using contron bar after
selecting “GREEN CUTOFF” in the menu.
3. Use control bar after selecting “BLUE
CUTOFF” in left menu to set the “y”
coordinate to 0.298 ± 0.02
4. Use control bar after selecting “RED
CUTOFF” in left menu to 0.283 ± 0.02
* If color values would not be matched desirable
values, repeat sequence 3 and 4 after readjusting
“GREEN CUTOFF” control a little different.
4-6
68 kHz/85 Hz
White Box Pattern
0.06ft-L at Back Raster
Pattern Display
Maximum
WHITE WINDOW
1. Click on the << or >> boxes next to R_GAIN
and B_GAIN to make the video white.
(For 9300K color adjustment:
x = 0.283 ± 0.02, y = 0.298 ± 0.02.)
Note: Do not touch the G_GAIN controls.
2. Check the ABL. If it is not within the
specifications (30 ± 1 ft-L), use the ABL
controls to adjust it.
3. Select COLOR FACTORY SAVE to save the
data.
4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION
CONDITIONS
Scanning frequency:
68 kHz/85 Hz
PN17K*/PN17J*
4 Alignment and Adjustments
Display image:
X-Y Coordinates:
ABL Luminance
Brightness:
Contrast:
Back raster pattern
Full White Pattern
x = 0.283 ± 0.02,
y = 0.298 ± 0.02
Refer to 4-3-2(c)
Maximum
5 ft-L, 24 ft-L
1. Check whether the color coordinates of the
back raster satisfy the above spec.
If they do not, return to 4-3-2 (a) and readjust
all settings.
4-3-4 Focus Adjustment
CONDITIONS
Scanning frequency:
Display image:
Brightness:
Contrast:
68 kHz/85 Hz
(1024 x 768)
“H” character pattern
Cut off point
Maximum
PROCEDURE
1. Adjust the Focus VR on the FBT to display the
sharpest image possible.
2. Display a full white pattern.
2. Use Locktite to seal the Focus VR in position.
3. Select “Geometry” in softjig menu.
4-3-5 Color Purity Adjustment
4. Select “@7: 5-ft “ in right menu.
Color purity is the absence of undesired color.
Conspicuous mislanding (unexpected color in a
uniform field) within the display area shall not be
visible at a distance of 50 cm from the CRT
surface.
5. Check whether the white coordinates of the
video meet the above coordinates spec.
6. Select “@8: 24-ft “ in right menu.
7. Check whether the white coordinates of the
video satisfies the above spec.
If they do not, return to 4-3-2 (a) and readjust
all settings.
Select “Color” and click “@2: CHANNEL 2”
for color ajdustment for 6500K
Repeat the sequence of 9300K adjustment.
The luminance values the same as 9300K, but
the color coordinated of back raster and white
box are : x = 0.313 ± 0.02 y = 0.329 ± 0.02
4-3-3 Luminance Uniformity Check
Luminance is considered uniform only if the ratio
of lowest to highest brightness areas on the screen
is not less than 7.5:10.
CONDITIONS
Scanning frequency:
Display image:
Brightness:
Contrast:
68 kHz/85 Hz
(1024 x 768)
White flat field
Cut off point at 0.06ft-L
Maximum
PROCEDURE
Measure luminance at nine points on the display
screen (see figure below).
CONDITIONS
Orientation:
Scanning frequency:
Display image:
Luminance:
Monitor facing east
68 kHz/85 Hz
White flat field
Cut off point at the center
of the display area
Note: Color purity adjustments should only be
attempted by qualified personnel.
PROCEDURE
For trained and experienced service technicians only.
Use the following procedure to correct minor
color purity problems:
1. Make sure the display is not affected by
external magnetic fields.
2. Make sure the spacing between the PCM
assembly and the CRT stem is 29 mm ± 1 mm.
3. Display a green pattern over the entire display
area.
4. Adjust the purity magnet rings on the PCM
assembly to display a pure green pattern.
(Optimum setting: x = 0.295 ± 0.015, y = 0.594 ± 0.015)
Table 4-4. Color Purity Tolerances
Red:
x = 0.640 ± 0.015
y = 0.323 ± 0.015
Green:
x = 0.295 ± 0.015
y = 0.594 ± 0.015
Blue:
x = 0.142 ± 0.015
y = 0.066 ± 0.015
(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02)
Figure 4-10. Luminance Uniformity Check Locations
PN17K*/PN17J*
5. When you have the PCMs properly adjusted,
carefully glue them together to prevent their
movement during shipping.
4-7
4 Alignment and Adjustments
Memo
4-8
PN17K*/PN17J*
5 Troubleshooting
5-1 Parts Level Troubleshooting
Notes: Check the following circuits.
• No raster appears: Power circuit, Horizontal output circuit.
• High voltage develops but no raster appears: Video output circuits.
• High voltage does not develop: Horizontal output circuits.
5-1-1 No Power Supply
WAVEFORMS
Check and replace D601 and FH1
1 100 V (IC601, #1)
Chirping noise exists?
Yes
Check and replace IC601.
No
Repeating start?
CH1 P-P = 100 V
Yes
CH1 RMS = 350.2 V
Check and replace D606.
No
1
IC601 Pin 1 waveform is right?
No
Check and replace D614, IC601,
Q602, and ZD601.
No
Check and replace IC201, IC301,
IC401, Q402, and Q404.
Yes
C622 Voltage is 13 V ± 0.5V?
Yes
Operate normally?
No
Replace Main board.
Yes
Verify voltages.
Done.
PN17K*/PN17J*
5-1
5 Troubleshooting
5-1-2 DPMS Failure
WAVEFORMS
Check signal source
H/V Sync. video level.
2 100V (IC601, #1)
Make No H/V Sync. (power off mode)
CH1 P-P = 100V
LED blinks?
No
CH1 RMS = 325.8 V
Check IC201 Pin 40.
Yes
+12 V line off?
No
Check IC201 Pin 6.
Yes
IC602 Pin 4
voltage exists?
No
Check IC201 Pin 6.
Check and replace IC602.
Yes
2
IC601 Pin 1 output
voltage exists?
No
Refer to 5-1-1 No Power Supply.
Yes
Done
5-2
PN17K*/PN17J*
5 Troubleshooting
5-1-3 H_Deflection Failure
3
Does PWM output signal appear
at Pin 6 (B_out) of IC401?
No
Yes
Does DC 12V appear at
Pin 10 of IC401?
No
Check 12 V line.
Yes
WAVEFORMS
Check IC401.
4
Does Horizontal pluse signal
appear at Pin 8 of IC401?
No
3 2.00 V (IC401, #6)
Check IC401.
CH1 P-P = 2.00V
Yes
CH1 RMS = 5.868V
4 2.00V (IC401, #8)
Does 110 Vp-p signal appear
5
at Collector of Q403?
No
Check Q403.
Yes
CH1 P-P = 2.00V
Check Q402, Q404 and T401.
CH1 RMS = 5.868V
5 20.0 V (Q404, Collector)
7-1-4 S Correction Failure
CH1 P-P = 20.0 V
CH1 RMS = 46.80V
Check S1 ~ S4 signal.
S1~S4 signals are right at each
frequency block?
No
Check and replace IC201.
Yes
Check and replace Q404, Q409,
Q410, Q411, Q414, Q415, Q416,
Q420, and Q421.
PN17K*/PN17J*
5-3
5 Troubleshooting
5-1-5 H_Lin. Failure
IC201 Pin 21 voltage varies with
different H_Lin. DAC values?
No
Replace IC201.
Yes
IC603 Pin 9 voltage varies with
different H_Lin. DAC values?
No
Check +13V, –10V line.
Check some parts around IC603.
Yes
Check Q412, Q413 and T402.
5-1-6 Invariable H_Size
IC401 Pin 6 voltage varies with
different B_Out DAC values?
No
Check and replace IC401.
Yes
Q402 Gate output duty varies with
different B_Out DAC values?
No
Check some parts around Q402,
IC401 Pin 3 ~ 6.
5-1-7 Abnormal H_Size
IC401 Pin 11 output duty
varies with different B+ offset
DAC values?
No
WAVEFORMS
Check and replace IC201.
6 200 V (Q404, Collector)
Yes
6
Q404 Collector waveform is
right?
No
Check and replace Q405,
Q406, Q407, and Q408.
CH1 P-P = 200V
CH1 RMS = 387.2V
Yes
Check some parts
around D409 and L401.
5-4
PN17K*/PN17J*
5 Troubleshooting
5-1-8 Side Pin or Trap Failure
7
IC401 Pin 11 output exists?
No
WAVEFORMS
Check and replace IC401.
7 1.00 V (IC401, #11)
Yes
Refer to 5-1-7 Abnormal H_Size.
CH1 P-P = 1.00V
CH1 RMS = 3.008 V
5-1-9 Para. or Pin Balance Failure
IC401 Pin 11 output varies with
different DAC values?
Yes
Refer to 5-1-7 Abnormal H_Size.
No
Replace IC401.
5-1-10 Tilt Failure
Check tilt connector connection
IC201 Pin 20 output duty varies
with different DAC values?
No
Check and replace IC201.
Yes
IC603 Pin 13 output varies with
different DAC values?
No
Check and replace IC603.
Yes
Check and replace Q301 and Q302.
PN17K*/PN17J*
5-5
5 Troubleshooting
5-1-11 V Deflection Failure
13V and –10V lines are on?
No
WAVEFORMS
Refer to 5-1-1 No Power Supply
8 500 V (IC401, #12)
Yes
8
IC401 Pin 12 output exists?
No
Check and replace IC401.
CH1 P-P = 500 V
9 10.0 V (IC301, #6)
Yes
9
IC301 Pin 6 output exists?
CH1 RMS = 1.425 V
No
Check and replace some parts
around IC301.
Yes
CH1 P-P = 10.0 V
CH1 RMS = 5.06 V
Check DY connector connection.
5-1-12 V Size or Position Variation Failure
IC401 Pin 12 output varies with
different DAC values?
No
Check and replace IC201 and IC401.
Yes
Check and replace IC301.
5-6
PN17K*/PN17J*
5 Troubleshooting
5-1-13 High Voltage Failure
WAVEFORMS
3
IC401 Pin 6 OSC pulse exists?
No
Check and replace IC401
and +12 V line.
3 2.00 V (IC401, #6)
Yes
10
Q402 Gate driving pulse exists?
No
Check and replace Q401 and Q423.
CH1 P-P = 2.00 V
CH1 RMS = 5.868 V
10 2.00 V (Q402, Gate)
Yes
11
Q402 Drain pulse exists?
No
Check and replace
D401, Q403 and L402.
CH1 P-P = 2.00 V
Yes
CH1 RMS = 7.692V
11 50.0 V (Q402, Drain)
Done
5-1-14 ABL Failure
CH1 P-P = 50.0 V
CH1 RMS = 73.7V
Input full white pattern to monitor.
IC101 Pin 8 input exists and
varies with different patterns?
No
Check and replace IC101.
Yes
Check CN102.
Yes
T501 Pin 8 output exists?
No
Check and replace T501.
Yes
IC201 Pin 26 output exists and
varies with different patterns?
No
Check and replace IC201.
Yes
Done
PN17K*/PN17J*
5-7
5 Troubleshooting
5-1-15 Dynamic Focus Failure
12
IC401 Pin 32 output is right?
No
WAVEFORMS
Replace the IC401.
12 2.00 V (IC401, #32)
Yes
Some parts around Q551 are right?
No
Replace failed part.
CH1 P-P = 2.00V
13 50.0 V (T502, #6)
Yes
13
T502 Pin 6 input is right?
No
Check and replace C432.
Yes
14
T502 Pin 1 output is right?
CH1 RMS = 6.124V
CH1 P-P = 50.0V
No
CH1 RMS = 75.6V
14 100 V (T502, #1)
Replace the T502.
No
Check the connection between FBT
Focus pin and CRT Socket PCB.
5-8
CH1 P-P = 100V
CH1 RMS = 124.0V
PN17K*/PN17J*
5 Troubleshooting
5-1-16 No Video
WAVEFORMS
Check signal cable and connection.
15 1.00V (IC101 #12,14,16)
15
IC101 Pin 12, 14 and 16 inputs
are right?
No
Check the signal cable connection.
Yes
16
IC101 Pin 18, 21 and 24
outputs are right?
CH1 P-P = 1.00V
No
CH1 RMS = 2.452V
16 1.00V (IC101 #18,21,24)
Check
I2C
bus and +12V line.
Yes
17
IC103 Pin 1, 2 and 3 outputs
are right?
No
Check +12V, +72 V line.
Check and replace IC103.
CH1 P-P = 1.00V
CH1 RMS = 2.792V
17 20.0V (IC103, #1, 2, 3)
Yes
Cathode DC levels are right?
No
Check +72V line.
Check and replace QR01, QR02,
QG01, QG02, QB01, and QB02.
CH1 P-P = 20.0V
CH1 RMS = 40.52V
Yes
G2 voltage is right?
No
Check G2 wire, CRT Socket board
and FBT.
Yes
Change CRT.
Done.
PN17K*/PN17J*
5-9
5 Troubleshooting
5-1-17 Micom Failure
IC201 Pin 11 input voltage is 5V?
No
WAVEFORMS
Check IC604.
18 1.00 V (IC201, #13, 14)
Yes
18
IC201 Pin 13 and 14 inputs
are right?
No
Check C202, C203 and X201.
CH1 P-P = 1.00 V
CH1 RMS = 2.108V
Yes
IC201 Pin 18 input is right?
No
Check IC605.
Yes
All in/output values are right?
No
Replace IC201.
Yes
Done
5-10
PN17K*/PN17J*
5 Troubleshooting
5-1-18 OSD Failure
WAVEFORMS
Check CN104 and connector Ass’y.
19 1.00 V (IC101, #32)
Yes
19
IC101 Pin 32 input is right?
No
Check amd replace Q102.
Check CN102 Pin 14.
Yes
20
IC101 Pin 1 input is right?
CH1 P-P = 1.00V
No
CH1 RMS = 4.516V
20 1.00 V (IC101, #1)
Check CN102 Pin 8.
Yes
IC101 Pin 29 and 30 inputs are
right?
No
Check IC201 Pin 41 and 42.
CH1 P-P = 1.00V
CH1 RMS = 5.024V
21 1.00 V (IC101, #18,21,24)
Yes
21
IC101 Pin 18, 21 and 24
outputs are right?
No
Check and replace IC101.
CH1 P-P = 1.00V
CH1 RMS = 2.580V
Yes
Check and replace IC103.
Done
PN17K*/PN17J*
5-11
5 Troubleshooting
5-1-19 User Control Failure
Does the DC level change at
Pin 36 of IC201 when you push the
button S/W?
No
Check the button.
(SW201 ~ SW204)
Yes
Check IC201.
5-1-20 Degaussing Failure
Check degaussing connector.
RL601 operation is right?
Yes
Check D-coil and TH601.
No
Q601 base input is right?
Yes
Check and replace Q601.
No
IC201 Pin 4 output is right?
No
Check and replace IC201.
Yes
Done
5-12
PN17K*/PN17J*
5 Troubleshooting
5-2 General Troubleshooting
5-2-1 No Picture
LED blinks?
Yes
Refer to 5-2-2 Shut down.
No
LED is green color?
Yes
Check Micom.
No
Check G2 voltage, high voltage
and R, G, B cathode voltage.
5-2-2 Shut Down
Blinking LED’s?
No
Check power supply.
Yes
Scan failure?
Yes
Check horizontal, vertical deflection
system and check power supply
secondary voltages.
No
Video failure?
Yes
Check Video board.
No
Check and replace IC201.
Done
PN17K*/PN17J*
5-13
5 Troubleshooting
5-2-3 Missing Color
WAVEFORMS
Proper Video levels are
on CN101 (D-Sub) Pin 1, 3 and 5?
No
Check signal generator.
22 10.0 V (R,G,B, Video)
Yes
22
Proper Video signal is
on all cathodes?
No
Refer to 5-1-16 No Video.
CH1 P-P = 10.0V
CH1 RMS = 17.02V
Yes
Proper DC voltage is
on all cathodes?
No
Check IC101 Pin 17, 20 and 23.
Check QR01, QR02, QG01,. QG02,
QB01, and QB02.
Yes
G2 voltage is right?
No
Check Q501 and D520.
Yes
Heater voltage is right?
No
Check D608, Q604 and T601.
Yes
G1 voltage is right?
No
Check D504, Q502 and T501.
Yes
Replace CRT.
Yes
Done
5-14
PN17K*/PN17J*
5 Troubleshooting
5-2-4 Visible Retrace
Check white balance adjustment.
G2 voltage is right?
No
WAVEFORMS
Check D502, D517 and Q501.
23 5.00V (Q303, Collector)
Yes
Blank pulse is on Pin 17 of IC401?
No
Check IC401.
CH1 P-P = 5.00V
24 20.00V (CRT Socket, G1)
Yes
23
V_FLB pulse is on
Collector of Q303?
No
Check Q303.
Yes
24
Does approve the Vertical pulse
on the CRT Socket G1?
CH1 RMS = 28.33V
CH1 P-P = 20.0V
No
CH1 RMS = 66.68V
Check CN102 and CN201.
Yes
Done
PN17K*/PN17J*
5-15
5 Troubleshooting
5-2-5 Unsynchronized Image
Check input signals Pin 2
and 3 of CN202.
Signals are right?
No
Check Video Cable
Yes
Signals at Pin 28 and 29 of
IC201 are right?
No
Check IC201.
Yes
Signals at Pin 14 and 15 of
IC401 are right?
No
Check IC401
Yes
Check circuits on Main board.
Done
5-16
PN17K*/PN17J*
5 Troubleshooting
5-2-6 Misconvergence
Try readjusting convergence.
The convergence is now
within spec.?
Yes
Done
No
Readjust convergence.
The convergence is now
within spec.?
Yes
Done
No
Change CRT and readjust
convergence.
Done
PN17K*/PN17J*
5-17
5 Troubleshooting
5-2-7 Poor Focus
Adjust focus VR of FBT.
Improved focus?
Yes
Aging monitor and check for focus
change.
No
Refer to 5-1-15 Dynamic
Focus Failure.
No
Check focus leads from FBT
to CRT Socket.
Check the CRT Socket.
Dynamic focus circuit is right?
Yes
Replace the CRT and verify focus.
5-2-8 Purity Failure
Degaussing
Purity is right?
Yes
Done
No
Degaussing circuit is right?
No
Refer to 5-1-20 Degaussing Failure.
Yes
Replace CRT and verify purity.
5-18
PN17K*/PN17J*
6 Exploded View and Parts List
6-1 PN17KT/JT
PN17K*/PN17J*
6-1
6 Exploded View & Parts List
6-2 PN17KO/JO
6-2
PN17K*/PN17J*
6 Exploded View and Parts List
6-1-1 Front Cover & CRT Ass’y (PN17KT/JT)
PN17K*/PN17J*
6-3
6 Exploded View & Parts List
6-1-2 Chassis & Stand Ass’y (PN17KT/JT)
6-4
PN17K*/PN17J*
6 Exploded View & Parts List
6-1-3 Rear Ass’y (PN17KT/JT)
PN17K*/PN17J*
6-5
6 Exploded View & Parts List
6-2-1 Front Cover & CRT Ass’y (PN17KO/JO)
6-6
PN17K*/PN17J*
6 Exploded View & Parts List
6-2-2 Chassis & Stand Ass’y (PN17KO/JO)
PN17K*/PN17J*
6-7
6 Exploded View & Parts List
6-2-3 Rear Ass’y (PN17KO/JO)
6-8
PN17K*/PN17J*
7 Electrical Parts List
7-1 Main PCB Parts (PN17K*)
Loc. No.
Code No.
Description
Specification
Remarks
B/PCB+LMF
BOTTOM
C409
C430
C601
C602
C608
CIS
CIS
CIS
CIS
CIS
CIS
CIS
CIS
CIS
CN201
CN202
CN203
CN403
CN601
D406
D601
D609
FBT
FBT+H/S
FUSE
IC201
IC201_SOCK
IC401
IC602
IC604
JW1
JW2
JW3
JW4
L401
L402
L403
L601
OP201
RL601
S/BTM+PCB
SH/BTM+AC/SOCK
SW401
SW601
T401
T402
T501
T502
T601
T602
TH601
TH602
70KHZ
BD301
BD401
BD402
BD403
BD555
BD601
6003-000010
2001-000066
2306-000147
2306-000249
2301-001195
2301-001195
2401-003391
BH39-00145A
BH39-00242A
BH68-00001A
BH71-00110A
BH72-00025A
BH72-00026A
BH72-00261A
BH73-60304C
BH46-00002M
3711-003895
3711-003873
BH39-00131A
3711-003989
3721-001028
0402-001025
0402-001407
0402-000005
6502-000001
6003-000122
3601-000004
0903-001166
3704-001071
1204-001509
1203-000165
1203-000001
BH39-00210A
BH39-00210A
BH39-40305Y
BH39-40306C
BH27-00005A
BH27-00022A
BH27-20342U
BH27-00061A
0601-001147
3501-001111
6003-000010
6003-000010
3406-000002
3403-001050
BH26-00027A
BH26-00028A
BH26-00026A
BH26-00057A
BH26-00059A
BH26-30302S
1404-000002
1404-001020
BH39-40305U
3301-000011
3301-000011
3301-000011
3301-000011
3301-000011
3301-000011
SCREW-TAPTITE
R-CARBON(S)
C-FILM,MPPF
C-FILM,MPPF
C-FILM,MPPF
C-FILM,MPPF
C-AL
CBF SIGNAL
CBF HARNESS
LABEL/MARK-CDT
SHIELD-BOTTOM
GUIDE-POWER
SHAFT-POWER
SHEET-LMF
RUBBER-SUPPORT
MICOM-S/W,PN17KT
CONNECTOR-HEADER
CONNECTOR-HEADER
CBF-HARNESS
CONNECTOR-HEADER
PLUG-AC POWER
DIODE-RECTIFIER
DIODE-BRIDGE
DIODE-RECTIFIER
CABLE CLAMP
SCREW-TAPTITE
FUSE-CARTRIDGE
IC-MICROCONTROLLER
SOCKET-IC
IC-HOR./VER.PROCESSO
IC-POSI.ADJUST REG.
IC-POSI.FIXED REG.
CBF-HARNESS
CBF-HARNESS
CBF-HARNESS
CBF-HARNESS
COIL-CHOKE
COIL-CHOKE
COIL-CHOKE
COIL FILTER
LED
RELAY-POWER
SCREW-TAPTITE
SCREW-TAPTITE
SWITCH-ROTARY
SWITCH-PUSH
TRANS-HOR.DRIVE
TRANS-H.LINEARITY
TRANS-FBT
TRANS-FOCUS
TRANS-POWER
TRANS-SYNC.
THERMISTOR-PTC
THERMISTOR-NTC
CBF HARNESS
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
BWH,+,B,M3,L10,ZPC(YEL),SWRCH1
10KOHM,5%,1/2W,AA,TP,2.4X6.4MM
1uF,5%,250V,BK,26x24x15,22.5mm
680nF,5%,250V,TP,26x20.5x12,20
150nF,10%,275VAC,BK,26x16.5x7,
150nF,10%,275VAC,BK,26x16.5x7,
220uF,20%,450V,GP,BK,25x50,10
ATT,1500MM,15P/6P,7P,IVORY(IV01),-,D-SUB/MALE
DB5907,UL1032,UL/CSA,1P,290MM,RED,AWG22,YFH800,YPT-018,-,-,-,-,-,-,CBF-GND ASS’Y
ART-PAPER 100G,-,WHT,BLK,-,ALL,CDT
PN15VT,SECC ,T1.0,-,-,CDA4507,ABS+PC,5V,IV16,-,CDA4507,ABS+PC,5V,IV16,-,IB10LO,AL+PET,-,-,-,-,-,DP15LT,CR V0,GRAY,-,14*7*10,-,PN17KT(PHOEINX),-,-,-,-,-,BOX,13P,1R,2mm,STRAIGHT,SN
BOX,7P,1R,2mm,STRAIGHT,SN
2P,80MM,BLU/WHT/YEL,UL1007,AWG26,SMP250-02/YBNH200-02
NOWALL,4P,1R,8mm,STRAIGHT,SN
3P,-,-,NI
ERD07-15,1.5KV,1.5A,-,TP
G2SB60,600V,1.5A,SIP-4,BK
31DF4,400V,3A,DO-201AD,BK
DAWH-5NB,D15,L35,NTR,NYLON66
BH,+,B,M4,L12,ZPC(YEL),SWRCH18
250V,3.15A,SLOW-BLOW,CERAMIC,5x20mm
3P8629,8Bit,DIP,42P,600MIL,12MHz,ST,CMOS,PLASTIC,5V,-,-40to+85C,464BYTE,32K,8Bit
42P,DIP,SN,1.778mm
TDA4859,DIP,32P,400MIL,PLASTIC,16V,-,-20TO+70CC,ST,H/V DEF. PROCESSOR
78R12,TO-220,3P,-,-,12V,-,0to+
7805,TO-220,3P,-,PLASTIC,4.8/5
DP17M**,UL1015,UL/CSA,-,60MM,BLK,AWG22,-,-,-,-,-,-,-,-,CBF-JUMPER WIRE
DP17M**,UL1015,UL/CSA,-,60MM,BLK,AWG22,-,-,-,-,-,-,-,-,CBF-JUMPER WIRE
,110MM,BLK,1015,AWG22,-,-,-,-,
,60MM,BLK,1015,AWG22,-,-,-,-,120UH,10%,AR-06*30,BULK,-,100UH,+/-10%,DR1523(C:9.8),BK,-,-,8.2MH(250KHz),10%,DR8*11,-,-,-,-,10.5OHM,-,-,-,BULK
-,33.0mH,0.1ohm,72Ts,28.*28,-,BK,SQE-2828,3A,-,ROUND,GRN,4.75mm,565nm
12Vdc,250mW,5A,1FormA,15mS,5mS
BWH,+,B,M3,L10,ZPC(YEL),SWRCH1
BWH,+,B,M3,L10,ZPC(YEL),SWRCH1
36Vdc,200mA,SP3T,30V,0.3A,SPDT,ON-OFF,PC BORD T
35.0MH,-,EI 1916,PL-3,-,310UH,5.2UH,6P,DR1425(C:5.0),YL-81,5.2UH/68.0MH,-,HL-1425E
1.1MH,-,3763SU,SM9C,-,-,3.8MH MIN,10P,EI-2218,(SB-5S),SB-5S,3.8MH/225MH MIN,40UH MAX,350UH,18P,EER 3541,PL3,PM2,7.0UH MAX.,0.22OHM,3-1(250UH),-,-,SB-5S,UU1116,39ohm,20%,-,-,TR,RECT,8ohm,15%,-,17mW/C,BK
52MM,AWG22(0.6PI),-,-,AWG22(0.
AA,3.5x1.0x5.7mm,1500,2375G
AA,3.5x1.0x5.7mm,1500,2375G
AA,3.5x1.0x5.7mm,1500,2375G
AA,3.5x1.0x5.7mm,1500,2375G
AA,3.5x1.0x5.7mm,1500,2375G
AA,3.5x1.0x5.7mm,1500,2375G
SNA
PN17K*/PN17J*
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
!
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
!
!
SNA
SNA
SNA
SNA
SNA
SNA
SNA
7-1
7 Electrical Parts List
Loc. No.
BD602
BD603
C201
C202
C203
C204
C205
C206
C207
C209
C210
C211
C212
C213
C214
C215
C216
C217
C220
C225
C301
C302
C305
C306
C307
C308
C309
C310
C311
C312
C313
C401
C402
C403
C404
C405
C406
C407
C408
C410
C411
C412
C413
C414
C415
C416
C417
C419
C420
C421
C423
C425
C426
C427
C429
C431
C432
C433
C434
C435
C436
7-2
Code No.
Description
3301-000011
3301-000011
2401-000025
2201-000389
2201-000389
2401-002075
2401-000603
2401-000050
2401-002075
2401-002075
2401-002075
2201-000146
2201-000017
2401-000029
2401-000025
2201-000146
2401-000603
2202-002009
2401-000037
2401-002075
2301-000010
2305-001041
2401-000037
2401-000856
2305-000237
2301-000004
2202-000252
2301-000519
2301-001027
2401-001016
2301-000010
2301-000312
2305-000665
2301-000148
2301-000004
2201-000823
2301-000013
2401-000540
2201-000556
2401-000037
2301-000180
2301-000519
2401-001012
2401-001334
2401-001218
2301-000010
2301-000321
2303-000165
2301-001305
2301-001341
2401-000603
2306-000131
2401-000603
2306-000171
2401-000603
2306-000179
2305-001033
2305-001003
2401-001016
2201-002079
2201-000672
CORE-FERRITE BEAD
CORE-FERRITE BEAD
C-AL
C-CERAMIC,DISC
C-CERAMIC,DISC
C-AL
C-AL
C-AL
C-AL
C-AL
C-AL
C-CERAMIC,DISC
C-CERAMIC,DISC
C-AL
C-AL
C-CERAMIC,DISC
C-AL
C-CERAMIC,MLC-AXIAL
C-AL
C-AL
C-FILM,PEF
C-FILM,MPEF
C-AL
C-AL
C-FILM,MPEF
C-FILM,PEF
C-CERAMIC,MLC-AXIAL
C-FILM,PEF
C-FILM,PEF
C-AL
C-FILM,PEF
C-FILM,PEF
C-FILM,MPEF
C-FILM,PEF
C-FILM,PEF
C-CERAMIC,DISC
C-FILM,PEF
C-AL
C-CERAMIC,DISC
C-AL
C-FILM,PEF
C-FILM,PEF
C-AL
C-AL
C-AL
C-FILM,PEF
C-FILM,PEF
C-FILM,PPF
C-FILM,PPF
C-FILM,PPF
C-AL
C-FILM,MPPF
C-AL
C-FILM,MPPF
C-AL
C-FILM,MPPF
C-FILM,MPEF
C-FILM,MPEF
C-AL
C-CERAMIC,DISC
C-CERAMIC,DISC
Specification
AA,3.5x1.0x5.7mm,1500,2375G
AA,3.5x1.0x5.7mm,1500,2375G
100uF,20%,16V,GP,TP,6.3x11,5
0.022nF,5%,50V,NP0,TP,5x3,5
0.022nF,5%,50V,NP0,TP,5x3,5
4.7uF,20%,50V,GP,TP,5x11,5
1uF,20%,50V,GP,TP,5x11,5
10uF,20%,16V,GP,TP,5x11,2.5
4.7uF,20%,50V,GP,TP,5x11,5
4.7uF,20%,50V,GP,TP,5x11,5
4.7uF,20%,50V,GP,TP,5x11,5
0.1nF,5%,50V,SL,TP,5x3.5,5
1nF,10%,50V,Y5P,TP,5x3.5,5
10uF,20%,100V,GP,TP,6.3x11,5
100uF,20%,16V,GP,TP,6.3x11,5
0.1nF,5%,50V,SL,TP,5x3.5,5
1uF,20%,50V,GP,TP,5x11,5
100nF,+80-20%,50V,Y5V,TP,2.3X3
470uF,20%,16V,GP,TP,8x11.5,5
4.7uF,20%,50V,GP,TP,5x11,5
100nF,5%,100V,TP,11.5x12.5mm,5
220nF,5%,63V,TP,7.5x4.5x13.5,5
470uF,20%,16V,GP,TP,8x11.5,5
220uF,20%,35V,WT,TP,10x20,5
1uF,5%,63V,TP,7.5x15.5mm,5mm
2.2nF,5%,100V,TP,5.5X10X2.9,5m
4.7nF,10%,50V,X7R,TP,2.5x4.3,3.3nF,5%,100V,TP,5.8x3x12.5,5m
15nF,10%,250V,TP,9.5x12x4.5,5m
3.3UF,20%,50V,BP,TP,5X11,5
100nF,5%,100V,TP,11.5x12.5mm,5
8.2nF,5%,100V,TP,6x12.5mm,5mm
100nF,5%,63V,TP,7.5x4.0x5.0mm,
10nF,5%,100V,TP,7x3.2x7mm,5mm
2.2nF,5%,100V,TP,5.5X10X2.9,5m
0.27nF,5%,50V,SL,TP,8x3.5,5
4.7nF,5%,100V,TP,10.5x12.5x6.5
150uF,20%,63V,LZ,TP,10x25,5
0.47nF,10%,500V,Y5P,TP,5.5x3,5
470uF,20%,16V,GP,TP,8x11.5,5
18nF,5%,100V,TP,7.2x4.0x7.5mm,
3.3nF,5%,100V,TP,5.8x3x12.5,5m
3.3UF,20%,50V,BP,TP,16X25,7.5
470nF,20%,50V,GP,TP,5x11,2.5
4.7uF,20%,100V,WT,TP,5x11,5
100nF,5%,100V,TP,11.5x12.5mm,5
8.2nF,5%,100V,TP,7x3.2x7mm,5mm
2.5nF,5%,1.6kV,TP,21x6.8x12.6mm,7.5
2.2NF,3%,1.6KV,TP,22X15.5X8.5MM,7.5
3.3nF,5%,630V,TP,17.4x10x5.4mm,7.5
1uF,20%,50V,GP,TP,5x11,5
150nF,5%,250V,TP,19x16x7.5,7.5
1uF,20%,50V,GP,TP,5x11,5
270nF,5%,250V,TP,21.5x12.5mm,7
1uF,20%,50V,GP,TP,5x11,5
300nF,5%,250V,TP,20x18.5x10.5,
15nF,10%,250V,TP,13X9.0X4.5mm,
10nF,5%,250V,TP,13x4.5x9mm,7.5
3.3UF,20%,50V,BP,TP,5X11,5
0.15nF,10%,500V,Y5P,TP,6.3x4mm,5
0.82nF,10%,500V,Y5P,TP,6.5x3,5
Remarks
SNA
SNA
!
!
PN17K*/PN17J*
7 Electrical Parts List
Loc. No.
C445
C446
C447
C448
C450
C501
C502
C503
C504
C505
C506
C507
C508
C509
C510
C511
C512
C513
C514
C530
C551
C552
C557
C603
C604
C607
C609
C610
C611
C612
C613
C614
C615
C616
C617
C618
C619
C620
C621
C622
C623
C624
C625
C626
C627
C630
C631
C635
CN304
CN603
D301
D401
D402
D403
D404
D405
D407
D410
D411
D412
D413
Code No.
Description
2201-000019
2201-000647
2201-000476
2305-000428
2305-000237
2301-000016
2301-000016
2401-000603
2301-000004
2401-000059
2201-000019
2201-000285
2401-002267
2401-002267
2301-000020
2301-000519
2301-000148
2201-000291
2401-001334
2201-000291
2401-000050
2201-000132
2401-001643
2201-000024
2201-000024
2202-002009
2401-000971
2301-000284
2401-000613
2401-000613
2201-000129
2201-000019
2201-000291
2201-000023
2201-000023
2401-000039
2201-000469
2401-000540
2401-001585
2401-000039
2401-000039
2201-000210
2305-001041
2401-000037
2401-000142
2401-001561
2202-002009
2201-000019
3711-000197
3711-000217
0402-000274
0402-000274
0402-000006
0402-000006
0402-000006
0402-000208
0402-001118
0402-000546
0402-000546
0402-000546
0402-000546
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-FILM,MPEF
C-FILM,MPEF
C-FILM,PEF
C-FILM,PEF
C-AL
C-FILM,PEF
C-FILM,MPEF
C-CERAMIC,DISC
C-CERAMIC,DISC
C-AL
C-AL
C-FILM,PEF
C-FILM,PEF
C-FILM,PEF
C-CERAMIC,DISC
C-AL
C-CERAMIC,DISC
C-AL
C-CERAMIC,DISC
C-AL
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,MLC-AXIAL
C-AL
C-FILM,PEF
C-AL
C-AL
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-AL
C-CERAMIC,DISC
C-AL
C-AL
C-AL
C-AL
C-CERAMIC,DISC
C-FILM,MPEF
C-AL
C-AL
C-AL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,DISC
CONNECTOR-HEADER
CONNECTOR-HEADER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
PN17K*/PN17J*
Specification
10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
0.068nF,5%,500V,NP0,TP,8x3.5mm,5
0.033nF,10%,500V,SL,TP,5.5x3,5
47nF,5%,250V,TP,11x9x4.5,5mm
1uF,5%,63V,TP,7.5x15.5mm,5mm
22nF,5%,100V,TP,7.2x4.5x9.0mm,
22nF,5%,100V,TP,7.2x4.5x9.0mm,
1uF,20%,50V,GP,TP,5x11,5
2.2nF,5%,100V,TP,5.5X10X2.9,5m
100nF,5%,63V,GP,-,5x11,5
10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
1nF,10%,1kV,Y5P,TP,8x5,5
2.2uF,20%,250V,GP,TP,8x11.5,5
2.2uF,20%,250V,GP,TP,8x11.5,5
27nF,5%,100V,TP,7.3x4x12.5mm,5
3.3nF,5%,100V,TP,5.8x3x12.5,5m
10nF,5%,100V,TP,7x3.2x7mm,5mm
1nF,10%,500V,Y5P,TP,7.5x3.5,5
470nF,20%,50V,GP,TP,5x11,2.5
1nF,10%,500V,Y5P,TP,7.5x3.5,5
10uF,20%,16V,GP,TP,5x11,2.5
0.1nF,10%,500V,Y5P,TP,6.5x3,5
0.68uF,20%,50V,GP,TP,5x11mm,5
4.7nF,20%,250VAC,Y5U,TP,16x7,7
4.7nF,20%,250VAC,Y5U,TP,16x7,7
100nF,+80-20%,50V,Y5V,TP,2.3X3
22uF,20%,50V,WT,TP,6x11mm,5mm
47nF,5%,100V,TP,8.5x12.5mm,5mm
1uF,20%,50V,WT,TP,5x11,5
1uF,20%,50V,WT,TP,5x11,5
0.1nF,10%,1kV,Y5P,TP,7x4,5
10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
1nF,10%,500V,Y5P,TP,7.5x3.5,5
2.2nF,20%,125V,Y5U,TP,11x7,5
2.2nF,20%,125V,Y5U,TP,11x7,5
1000uF,20%,16V,GP,TP,10x16,5
0.33nF,10%,500V,Y5P,TP,5.5x3,5
150uF,20%,63V,LZ,TP,10x25,5
47uF,20%,50V,WT,TP,8x11.5,5
1000uF,20%,16V,GP,TP,10x16,5
1000uF,20%,16V,GP,TP,10x16,5
0.12NF,10%,1KV,Y5P,TP,6.3X4MM,5
220nF,5%,63V,TP,7.5x4.5x13.5,5
470uF,20%,16V,GP,TP,8x11.5,5
1000uF,20%,16V,WT,TP,10x20,5
47uF,20%,35V,WT,TP,8x11.5,5
100nF,+80-20%,50V,Y5V,TP,2.3X3
10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
1WALL,3P,1R,2.5mm,STRAIGHT,SN
1WALL,3P,1R,3.96mm,STRAIGHT,SN
UF4004,400V,1A,DO-41,TP
UF4004,400V,1A,DO-41,TP
1N4007GP,1000V,1A,DO-41,TP
1N4007GP,1000V,1A,DO-41,TP
1N4007GP,1000V,1A,DO-41,TP
EK-04,40V,1.5A,DO-41
UF1G,400V,1.2A,DO-204AL,TP
TVR10G,400V,1.0A,DO-41,TP
TVR10G,400V,1.0A,DO-41,TP
TVR10G,400V,1.0A,DO-41,TP
TVR10G,400V,1.0A,DO-41,TP
Remarks
!
SNA
SNA
7-3
7 Electrical Parts List
Loc. No.
D420
D421
D422
D431
D432
D501
D502
D503
D504
D505
D506
D507
D508
D509
D510
D511
D512
D513
D515
D516
D517
D518
D519
D602
D604
D605
D606
D607
D608
D610
D611
D612
D614
D615
D616
D617
EY301
EY302
EY401
EY402
EY403
EY501
EY502
EY503
EY504
EY505
EY506
EY507
EY508
EY510
EY601
EY602
EY603
EY604
EY605
EY606
EY607
EY608
EY609
EY610
FH1
7-4
Code No.
Description
0401-000005
0401-000005
0401-000004
0401-000005
0402-000546
0401-000005
0402-000017
0402-000017
0402-000017
0401-000004
0402-000546
0401-000005
0401-000005
0401-000005
0401-000005
0401-000005
0402-000017
0401-000005
0401-000005
0401-000005
0402-000017
0401-000004
0401-000005
0401-000005
0402-000012
0402-000012
0402-000546
0401-000005
0402-000274
0402-000012
0402-001194
0402-000274
0402-000546
0401-000005
0401-000005
0402-001039
6042-000001
6042-000001
6042-000002
6042-000002
6042-000002
6042-000001
6042-000001
6042-000001
6042-000002
6042-000002
6042-000002
6042-000002
6042-000002
6042-000001
6042-000001
6042-000001
6042-000001
6042-000001
6042-000001
6042-000001
6042-000002
6042-000002
6042-000002
6042-000002
3602-000001
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-RECTIFIER
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
EYELET
FUSE-CLIP
Specification
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1SS244,250V,625mA,DO-34,TP
1N4148,100V,200mA,DO-35,TP
TVR10G,400V,1.0A,DO-41,TP
1N4148,100V,200mA,DO-35,TP
RGP02-12,1200V,0.5A,DO-204AL,T
RGP02-12,1200V,0.5A,DO-204AL,T
RGP02-12,1200V,0.5A,DO-204AL,T
1SS244,250V,625mA,DO-34,TP
TVR10G,400V,1.0A,DO-41,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
RGP02-12,1200V,0.5A,DO-204AL,T
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
RGP02-12,1200V,0.5A,DO-204AL,T
1SS244,250V,625mA,DO-34,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
UF4007,1KV,1A,DO-41,TP
UF4007,1KV,1A,DO-41,TP
TVR10G,400V,1.0A,DO-41,TP
1N4148,100V,200mA,DO-35,TP
UF4004,400V,1A,DO-41,TP
UF4007,1KV,1A,DO-41,TP
UG2D,200V,2A,DO-204AC,TP
UF4004,400V,1A,DO-41,TP
TVR10G,400V,1.0A,DO-41,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
SB020,20V,600mA,MPG06,TP
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
-,-,30mohm
Remarks
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
PN17K*/PN17J*
7 Electrical Parts List
Loc. No.
GT501
GT603
GT604
IC202
IC603
IC605
J19
JP1
JP10
JP11
JP12
JP13
JP14
JP15
JP16
JP17
JP18
JP2
JP20
JP22
JP23
JP24
JP25
JP26
JP27
JP28
JP29
JP3
JP31
JP32
JP33
JP34
JP35
JP36
JP37
JP38
JP39
JP4
JP40
JP41
JP42
JP43
JP44
JP45
JP46
JP47
JP48
JP5
JP50
JP51
JP52
JP53
JP54
JP55
JP56
JP57
JP58
JP59
JP6
JP60
JP61
Code No.
BH71-40300A
BH71-40300A
BH71-40300A
1103-001149
1201-000229
1203-000495
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
PN17K*/PN17J*
Description
PIN-HINGE
PIN-HINGE
PIN-HINGE
IC-EEPROM
IC-OP AMP
IC-RESET
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
Specification
-,BRASS,D2.36,SN,HEAT/SINK
-,BRASS,D2.36,SN,HEAT/SINK
-,BRASS,D2.36,SN,HEAT/SINK
524C80D41,4KBit,DIP,8P,300MIL,10mS,5V,10%,PLASTIC,-25to+70C,10uA,CMOS,ST
324,DIP,14P,300MIL,QUAD,100V/m
7045,T0-92,3P,-,PLASTIC,4.3/4.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
Remarks
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
7-5
7 Electrical Parts List
Loc. No.
JP63
JP64
JP65
JP67
JP68
JP7
JP70
JP71
JP72
JP76
JP8
JP82
JP84
JP85
JP9
MP1.0
Q301
Q302
Q303
Q401
Q405
Q406
Q407
Q412
Q413
Q414
Q415
Q416
Q423
Q501
Q502
Q503
Q551
Q601
Q602
Q604
Q608
Q609
Q610
R200
R201
R202
R203
R204
R206
R207
R208
R209
R210
R211
R212
R213
R214
R215
R216
R217
R218
R220
R221
R222
R223
7-6
Code No.
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH41-00136A
0501-000586
0501-000303
0501-000413
0501-000122
0501-000303
0501-000303
0501-000140
0501-000404
0501-000321
0501-000586
0501-000586
0501-000586
0501-000303
0501-000143
0501-000143
0501-000303
0501-000413
0501-000586
0501-000122
0501-000404
0501-000010
0501-002228
0501-000586
2001-000869
2001-000786
2001-000290
2001-000734
2001-000734
2001-000515
2001-000869
2001-000869
2001-000734
2001-000472
2001-000878
2001-000660
2001-000429
2001-000429
2001-000281
2001-000281
2001-000281
2001-000281
2001-000281
2001-000734
2001-000734
2001-000038
Description
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
PCB MAIN
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
Specification
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
PN17KT,FR1,1,-,1.6T,247*247,-,-,-,KSC945,NPN,250mW,TO-92,TP,120-240
KSA733,PNP,250mW,TO-92,TP,120-240
KSP44,NPN,625mW,TO-92,TP,50-200
2N3904,NPN,625mW,TO-92,TP,100-300
KSA733,PNP,250mW,TO-92,TP,120-240
KSA733,PNP,250mW,TO-92,TP,120-240
2N5551,NPN,625mW,TO-92,TP,80-250
KSD1616-Y,NPN,750mW,TO-92,TP,135-270
KSB1116-Y,PNP,750mW,TO-92,TP,135-270
KSC945,NPN,250mW,TO-92,TP,120-240
KSC945,NPN,250mW,TO-92,TP,120-240
KSC945,NPN,250mW,TO-92,TP,120-240
KSA733,PNP,250mW,TO-92,TP,120-240
2N6520,PNP,625mW,TO-92,TP,30-200
2N6520,PNP,625mW,TO-92,TP,30-200
KSA733,PNP,250mW,TO-92,TP,120-240
KSP44,NPN,625mW,TO-92,TP,50-200
KSC945,NPN,250mW,TO-92,TP,120-240
2N3904,NPN,625mW,TO-92,TP,100-300
KSD1616-Y,NPN,750mW,TO-92,TP,135-270
KSC1008,NPN,800mW,TO-92,TP,120-240
KTA1281,PNP,1000mW,TO-92L,TP,120-240
KSC945,NPN,250mW,TO-92,TP,120-240
56OHM,5%,1/8W,AA,TP,1.8X3.2MM
47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
220OHM,5%,1/8W,AA,TP,1.8X3.2MM
56OHM,5%,1/8W,AA,TP,1.8X3.2MM
56OHM,5%,1/8W,AA,TP,1.8X3.2MM
4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
33KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
390OHM,5%,1/4W,AA,TP,2.4X6.4MM
Remarks
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
!
!
PN17K*/PN17J*
7 Electrical Parts List
Loc. No.
R224
R225
R229
R230
R235
R236
R239
R301
R302
R303
R304
R306
R307
R308
R309
R310
R311
R312
R315
R316
R317
R318
R319
R320
R321
R322
R323
R324
R325
R326
R402
R403
R404
R405
R406
R407
R408
R409
R410
R411
R412
R413
R414
R415
R416
R417
R418
R419
R420
R422
R423
R424
R425
R426
R427
R428
R429
R430
R431
R432
R433
Code No.
2001-000869
2001-000869
2001-000281
2001-000290
2001-000472
2001-000290
2001-000290
2001-000869
2004-000580
2001-000890
2001-000890
2004-001022
2001-001048
2001-000037
2004-004014
2004-001136
2001-000890
2001-000812
2004-004014
2001-000281
2001-000561
2001-000766
2001-000947
2001-000331
2001-000591
2001-000890
2001-000022
2001-000660
2003-000805
2003-000805
2001-000869
2004-001226
2004-000498
2001-000591
2001-000522
2001-000109
2001-000429
2001-000812
2001-000105
2001-001096
2001-000290
2001-001038
2001-001038
2003-000432
2001-000107
2001-000331
2001-000221
2001-000004
2001-000395
2001-001006
2001-000258
2004-000284
2001-000119
2001-000110
2001-000591
2003-000483
2001-000052
2001-001078
2003-000407
2001-000020
2003-000769
PN17K*/PN17J*
Description
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-METAL
R-CARBON
R-CARBON
R-METAL
R-CARBON(S)
R-CARBON(S)
R-METAL
R-METAL
R-CARBON
R-CARBON
R-METAL
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON(S)
R-CARBON
R-METAL OXIDE(S)
R-METAL OXIDE(S)
R-CARBON
R-METAL
R-METAL
R-CARBON
R-CARBON
R-CARBON(S)
R-CARBON
R-CARBON
R-CARBON
R-CARBON(S)
R-CARBON
R-CARBON(S)
R-CARBON(S)
R-METAL OXIDE(S)
R-CARBON(S)
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-METAL
R-CARBON
R-CARBON
R-CARBON
R-METAL OXIDE(S)
R-CARBON(S)
R-CARBON(S)
R-METAL OXIDE(S)
R-CARBON(S)
R-METAL OXIDE(S)
Specification
56OHM,5%,1/8W,AA,TP,1.8X3.2MM
56OHM,5%,1/8W,AA,TP,1.8X3.2MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
56OHM,5%,1/8W,AA,TP,1.8X3.2MM
22Kohm,1%,1/4W,AA,TP,2.4x6.4mm
6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
5.6Kohm,1%,1/4W,AA,TP,2.4x6.4m
1.2OHM,5%,1/2W,AA,TP,2.4X6.4MM
330OHM,5%,1/2W,AA,TP,2.4X6.4MM
2.4ohm,1%,1/4W,AA,TP,2.4x6.4mm
6.8Kohm,1%,1/4W,AA,TP,2.4x6.4m
6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM
2.4ohm,1%,1/4W,AA,TP,2.4x6.4mm
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
27KOHM,5%,1/4W,AA,TP,2.4X6.4MM
43KOHM,5%,1/8W,AA,TP,1.8X3.2MM
7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
33OHM,5%,1/2W,AA,TP,2.4X6.4MM
33KOHM,5%,1/8W,AA,TP,1.8X3.2MM
82ohm,5%,1W,AA,TP,3.3x9mm
82ohm,5%,1W,AA,TP,3.3x9mm
56OHM,5%,1/8W,AA,TP,1.8X3.2MM
750ohm,1%,1/4W,AA,TP,2.4x6.4mm
2.7Kohm,1%,1/4W,AA,TP,2.4x6.4m
3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/2W,AA,TP,2.4X6.4MM
1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1.5KOHM,5%,1/4W,AA,TP,2.4X6.4MM
2.2OHM,5%,1/2W,AA,TP,2.4X6.4MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
0.56OHM,5%,1/2W,AA,TP,2.4X6.4MM
0.56OHM,5%,1/2W,AA,TP,2.4X6.4MM
1.5Kohm,5%,3W,AA,TP,6x16mm
150KOHM,5%,1/2W,AA,TP,2.4X6.4MM
12KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
200KOHM,5%,1/8W,AA,TP,1.8X3.2MM
180KOHM,5%,1/4W,AA,TP,2.4X6.4MM
82OHM,5%,1/8W,AA,TP,1.8X3.2MM
1.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM
12Kohm,1%,1/4W,AA,TP,2.4x6.4mm
680OHM,5%,1/4W,AA,TP,2.4X6.4MM
10OHM,5%,1/4W,AA,TP,2.4X6.4MM
3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM
120ohm,5%,3W,AA,TP,6x16mm
3.3KOHM,5%,1/2W,AA,TP,2.4X6.4MM
15KOHM,5%,1/2W,AA,TP,2.4X6.4MM
0.6ohm,5%,2W,AA,TP,4x12mm
22OHM,5%,1/2W,AA,TP,2.4X6.4MM
680ohm,5%,3W,AA,TP,6x16mm
Remarks
!
!
!
7-7
7 Electrical Parts List
Loc. No.
R434
R435
R436
R437
R438
R439
R440
R441
R443
R444
R445
R446
R447
R448
R449
R450
R451
R452
R453
R454
R458
R459
R460
R500
R501
R502
R503
R504
R505
R506
R507
R508
R509
R510
R511
R512
R513
R514
R515
R516
R518
R519
R524
R525
R526
R527
R529
R530
R531
R532
R551
R552
R553
R554
R555
R556
R560
R561
R570
R600
7-8
Code No.
2001-000449
2001-000786
2001-000449
2001-000786
2001-000449
2001-000786
2001-000947
2001-000411
2003-000578
2001-000739
2001-001079
2001-000117
2003-000777
2003-000777
2001-000211
2001-000522
2001-000290
2001-000290
2001-000290
2003-000650
2003-000650
2001-000938
2003-000724
2001-000435
2001-000472
2004-000979
2001-000449
2001-000008
2001-000008
2004-000643
2004-000216
2002-000121
2002-000121
2001-000837
2001-000478
2001-000786
2001-000087
2002-001069
2001-000546
2002-001056
2001-001031
2001-000356
2001-000660
2001-000273
2001-000702
2001-000011
2001-000429
2001-000397
2001-000508
2001-000432
2001-000530
2001-000495
2001-000642
2002-001049
2001-000042
2001-000613
2002-000121
2001-000432
2001-000085
2001-001129
Description
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-METAL OXIDE(S)
R-CARBON
R-CARBON(S)
R-CARBON(S)
R-METAL OXIDE(S)
R-METAL OXIDE(S)
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-METAL OXIDE(S)
R-METAL OXIDE(S)
R-CARBON
R-METAL OXIDE(S)
R-CARBON
R-CARBON
R-METAL
R-CARBON
R-CARBON
R-CARBON
R-METAL
R-METAL
R-COMPOSITION
R-COMPOSITION
R-CARBON
R-CARBON
R-CARBON
R-CARBON(S)
R-COMPOSITION
R-CARBON
R-COMPOSITION
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-COMPOSITION
R-CARBON
R-CARBON
R-COMPOSITION
R-CARBON
R-CARBON(S)
R-CARBON(S)
Specification
2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
18KOHM,5%,1/8W,AA,TP,1.8X3.2MM
220ohm,5%,2W,AA,TP,4x12mm
4.7MOHM,5%,1/8W,AA,TP,1.8X3.2MM
15OHM,5%,1/2W,AA,TP,2.4X6.4MM
68OHM,5%,1/2W,AA,TP,2.4X6.4MM
68ohm,5%,2W,AA,TP,4x12mm
68ohm,5%,2W,AA,TP,4x12mm
1OHM,5%,1/4W,AA,TP,2.4X6.4MM
22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
330ohm,5%,2W,AA,TP,4x12mm
330ohm,5%,2W,AA,TP,4x12mm
68OHM,5%,1/8W,AA,TP,1.8X3.2MM
5.6ohm,5%,3W,AA,TP,6x16mm
1MOHM,5%,1/8W,AA,TP,1.8X3.2MM
2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
47Kohm,1%,1/4W,AA,TP,2.4x6.4mm
2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
15KOHM,5%,1/8W,AA,TP,1.8X3.2MM
270Kohm,1%,1/4W,AA,TP,2.4x6.4m
10Kohm,1%,1/4W,AA,TP,2.4x6.4mm
1Mohm,10%,1/2W,AA,TP,3.5x9.5mm
1Mohm,10%,1/2W,AA,TP,3.5x9.5mm
51KOHM,5%,1/8W,AA,TP,1.8X3.2MM
2.7OHM,5%,1/4W,AA,TP,2.4X6.4MM
47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
120KOHM,5%,1/2W,AA,TP,2.4X6.4MM
51Kohm,5%,1/4,AA,TP,2.5x6.5mm
270KOHM,5%,1/4W,AA,TP,2.4X6.4MM
180Kohm,2%,1/4W,AA,TP,2.5x6.5mm
91KOHM,5%,1/8W,AA,TP,1.8X3.2MM
150KOHM,5%,1/8W,AA,TP,1.8X3.2MM
33KOHM,5%,1/8W,AA,TP,1.8X3.2MM
100KOHM,5%,1/8W,AA,TP,1.8X3.2MM
39KOHM,5%,1/8W,AA,TP,1.8X3.2MM
75KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
180KOHM,5%,1/8W,AA,TP,1.8X3.2MM
220KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1MOHM,5%,1/4W,AA,TP,2.4X6.4MM
240KOHM,5%,1/4W,AA,TP,2.4X6.4MM
20KOHM,5%,1/4W,AA,TP,2.4X6.4MM
330KOHM,5%,1/2W,AA,TP,3.3X9MM
240Kohm,5%,1/2W,AA,TP,3.9x9mm
1KOHM,5%,1/4W,AA,TP,2.4X6.4MM
3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1Mohm,10%,1/2W,AA,TP,3.5x9.5mm
1MOHM,5%,1/4W,AA,TP,2.4X6.4MM
100KOHM,5%,1/2W,AA,TP,2.4X6.4MM
330KOHM,5%,1/2W,AA,TP,2.4X6.4MM
Remarks
!
!
!
!
!
!
PN17K*/PN17J*
7 Electrical Parts List
Loc. No.
Code No.
Description
Specification
Remarks
R601
R602
R603
R604
R605
R607
R608
R609
R610
R611
R612
R613
R614
R615
R616
R617
R618
R619
R620
R621
R625
R626
R627
R630
R631
R632
SK501
TP501
X201
ZD201
ZD202
ZD203
ZD204
ZD205
ZD206
ZD207
ZD502
ZD503
ZD601
ZD602
ZD604
2001-001129
2001-000023
2001-000290
2001-000857
2001-000734
2003-000014
2001-000281
2002-001068
2002-001068
2001-001079
2003-000738
2001-000290
2001-001107
2001-001088
2001-001108
2001-001037
2001-000429
2003-000471
2001-000354
2001-000989
2001-000786
2001-000044
2004-001022
2001-000786
2001-000429
2001-000290
4715-000001
6042-000002
2801-000005
0403-000361
0403-000361
0403-000361
0403-000361
0403-000361
0403-000361
0403-000361
0403-001068
0403-000355
0403-000361
0403-001068
0403-001274
R-CARBON(S)
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-METAL OXIDE(S)
R-CARBON
R-COMPOSITION
R-COMPOSITION
R-CARBON(S)
R-METAL OXIDE(S)
R-CARBON
R-CARBON(S)
R-CARBON(S)
R-CARBON(S)
R-CARBON(S)
R-CARBON
R-METAL OXIDE(S)
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-METAL
R-CARBON
R-CARBON
R-CARBON
SURGE ABSORBER
EYELET
CRYSTAL-UNIT
DIODE-ZENER
DIODE-ZENER
DIODE-ZENER
DIODE-ZENER
DIODE-ZENER
DIODE-ZENER
DIODE-ZENER
DIODE-ZENER
DIODE-ZENER
DIODE-ZENER
DIODE-ZENER
DIODE-ZENER
330KOHM,5%,1/2W,AA,TP,2.4X6.4MM
47OHM,5%,1/4W,AA,TP,2.4X6.4MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
560OHM,5%,1/8W,AA,TP,1.8X3.2MM
4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10Kohm,5%,3W,AA,TP,6x16mm
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
180Kohm,5%,1/2W,AA,TP,3.9x9mm
180Kohm,5%,1/2W,AA,TP,3.9x9mm
15OHM,5%,1/2W,AA,TP,2.4X6.4MM
56Kohm,5%,2W,AA,TP,4x12mm
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
220ohm,5%,1/2W,AA,TP,2.4x6.4mm
1KOHM,5%,1/2W,AA,TP,2.4X6.4MM
22KOHM,5%,1/2W,AA,TP,2.4X6.4MM
0.39OHM,5%,1/2W,AA,TP,2.4X6.4MM
1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10ohm,5%,2W,AA,TP,4x12mm
150KOHM,5%,1/4W,AA,TP,2.4X6.4MM
820KOHM,5%,1/8W,AA,TP,1.8X3.2MM
47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM
5.6Kohm,1%,1/4W,AA,TP,2.4x6.4m
47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1KV,+50-10%,-,-,
ID1.5,OD2,L3.1,SN,BSS3-E/EH
8MHz,50ppm,28-AAM,S,35ohm,TP
UZ6.2BSB,6.2V,5.99-6.24V,500mW
UZ6.2BSB,6.2V,5.99-6.24V,500mW
UZ6.2BSB,6.2V,5.99-6.24V,500mW
UZ6.2BSB,6.2V,5.99-6.24V,500mW
UZ6.2BSB,6.2V,5.99-6.24V,500mW
UZ6.2BSB,6.2V,5.99-6.24V,500mW
UZ6.2BSB,6.2V,5.99-6.24V,500mW
UZ4.7BSA,4.7V,4.47-4.65V,500mW
UZ5.1BSB,5.1V,4.97-5.18V,500mW
UZ6.2BSB,6.2V,5.99-6.24V,500mW
UZ4.7BSA,4.7V,4.47-4.65V,500mW
UZ24BSC,23.29-24.27V,500MW,DO-34,TP
HS301
CIS
CIS
CIS
CIS
BH99-00002A
1204-001508
6006-001008
6021-000118
BH62-00003A
ASSY,HEAT/SINK
IC-VERTICAL DEF.
SCREW-ASS’Y MACH
NUT-HEXAGON
HEAT/SINK-V.IC
H/S V.IC,SCREW+NUT,KA2142,-,-,OIL SILICON,-,KA2142,SIP,10P,-,PLASTIC,35V,15W,-20TO+70C,ST,VERTICAL DEFLECTION
WSP,BH,+,M3,L10,ZPC(YEL),SWRCH
1C,M3,ZPC(YEL),SM20C
-,T1,-,A1050S,DA/DB
HS601
CIS
CIS
CIS
CIS
BH99-00003A
BH13-00004A
BH61-00004A
BH62-00004A
BH62-20001B
ASSY,HEAT/SINK
IC-HYBRID
SPRING-TR
HEAT/SINK-POWER
RUBBER
H/S POWER,SPRING,DP104,-,-,RUBBER,-,-,DP104C,TO-220-5L,5P,POWER SWITCH,-,CDA,CDB,SUS304,T0.5,-,-,-,-,T1,-,A1050S,DA/DB
CSQ4357,W25*L20*T0.45,-,-,-,-
SNA
SNA
SNA
HS401
CIS
CIS
CIS
BH99-00006A
6006-001008
6021-000118
BH62-30024A
ASSY,HEAT/SINK
SCREW-ASS’Y MACH
NUT-HEXAGON
HEAT/SINK-TR
H/S,SCREW+NUT,IRF630,-,-,OIL SILICON,-,WSP,BH,+,M3,L10,ZPC(YEL),SWRCH
1C,M3,ZPC(YEL),SM20C
SPC,T1,SN,CFX1577L
SNA
SNA
SNA
SNA
HS501
CIS
BH99-00009B
0402-001255
ASSY HEAT/SINK
DIODE-RECTIFIER
HS FBT,SPRING,2SC5440,DTV56F,KTD2058,OIL SILICON,-,DTV56F,1.5KV,10A,TO-220AC,BK
SNA
PN17K*/PN17J*
SNA
SNA
SNA
SNA
SNA
SNA
7-9
7 Electrical Parts List
Loc. No.
Code No.
Description
Specification
Remarks
CIS
CIS
CIS
CIS
CIS
0502-000465
0502-001170
BH61-00004A
BH61-70003A
BH62-00015A
TR-POWER
TR-POWER
SPRING-TR
SPRING
HEAT SINK-FBT
KTD2058,NPN,25000mW,TO-220IS,ST,100-200
2SC5440,NPN,60000mW,TOP-3E,ST,-8
CDA,CDB,SUS304,T0.5,-,-,-,CVT4857,STS304-W1/2H,T0.5,W3.8
A1050S,T1.0,T1.0,-,-
SNA
SNA
SNA
HS402
CIS
CIS
BH99-00010A
BH61-00004A
BH62-00016A
ASSY,HEAT/SINK
SPRING-TR
HEAT SINK-TR
HS TR,SPRING,IRF634A,-,-,OIL SILICON,-,CDA,CDB,SUS304,T0.5,-,-,-,A1050S,T1.0,-,DP17MO
SNA
SNA
SNA
HS409
CIS
CIS
CIS
BH99-10019U
0202-001044
0402-001191
BH62-30024B
ASSY HEAT/SINK
SOLDER-WIRE.
DIODE-RECTIFIER
HEAT/SINK-IC
HS TR,SOLDER,MUR460,-,-,S63S-W3.0,S63S,D3,63Sn/37Pb,MUR460,600V,4A,CASE267-03,BK
SPC-1,T1,SN COATING,-
SNA
SNA
7-10
SNA
PN17K*/PN17J*
7 Electrical Parts List
7-2 Video PCB Parts (PN17K*)
Loc. No.
C160
CIS
CIS
CIS
CIS
CIS
CIS
CIS
CIS
CN101
CN102
IC101
JP146
LJP1
S/VID
S/VID+H/S
SK01
BD102
BD103
C102
C103
C105
C106
C107
C108
C112
C113
C114
C116
C117
C118
C119
C120
C121
C123
C124
C128
C151
C152
CB01
CB02
CB04
CB05
CB06
CB07
CB08
CB09
CG01
CG02
CG04
CG05
CG06
CG07
CG08
CG09
CR01
CR02
CR04
CR05
CR06
CR07
CR08
CR09
D102
Code No.
2401-000039
BH75-00047A
BH71-00006B
BH71-10311A
BH75-00192H
BH61-00002A
BH71-00007A
BH72-00024A
BH73-00014A
3711-004228
BH39-00015A
1204-001646
BH39-40305U
BH39-40306D
6502-000001
6003-000010
3704-001116
3301-000011
3301-000011
2401-000603
2401-000037
2301-000010
2202-002009
2401-000010
2401-000049
2401-002075
2301-000287
2201-000117
2301-000188
2301-000188
2201-000471
2201-000291
2201-000285
2202-002009
2201-000019
2301-000148
2201-000119
2202-002009
2202-002009
2201-000119
2201-000119
2401-000055
2301-000010
2202-002009
2201-000146
2201-000411
2201-000247
2201-000119
2201-000119
2401-000055
2301-000010
2202-002009
2201-000146
2201-000411
2201-000247
2201-000119
2201-000119
2401-000055
2301-000010
2202-002009
2201-000146
2201-000411
2201-000247
0401-000005
PN17K*/PN17J*
Description
C-AL
UNIT/SHIELD-VIDEO/CAP
SHIELD-VIDEO/CAP
EARTH-PLATE
UNIT/SHIELD-VIDEO
SPRING-VIDEO
SHIELD-VIDEO
HOLDER-VIDEO
HOLDER-RUBBER(NORMAL)
CONNECTOR-HEADER
CBF-HARNESS
IC-OSD PROCESSOR
CBF HARNESS
CBF-HARNESS
CABLE CLAMP
SCREW-TAPTITE
SOCKET-CRT
CORE-FERRITE BEAD
CORE-FERRITE BEAD
C-AL
C-AL
C-FILM,PEF
C-CERAMIC,MLC-AXIAL
C-AL
C-AL
C-AL
C-FILM,PEF
C-CERAMIC,DISC
C-FILM,PEF
C-FILM,PEF
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,MLC-AXIAL
C-CERAMIC,DISC
C-FILM,PEF
C-CERAMIC,DISC
C-CERAMIC,MLC-AXIAL
C-CERAMIC,MLC-AXIAL
C-CERAMIC,DISC
C-CERAMIC,DISC
C-AL
C-FILM,PEF
C-CERAMIC,MLC-AXIAL
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-AL
C-FILM,PEF
C-CERAMIC,MLC-AXIAL
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
C-AL
C-FILM,PEF
C-CERAMIC,MLC-AXIAL
C-CERAMIC,DISC
C-CERAMIC,DISC
C-CERAMIC,DISC
DIODE-SWITCHING
Specification
1000uF,20%,16V,GP,TP,10x16,5
CL17LO,SPTE T0.3,-,-,CL17LO,SPTE,0.2,-,PBS 3/4H,T0.2
DEL,-,SPTE,-,-,14,15,17,CDB7907,STS H14 ,T1.0,-,-,-,NORMAL CDT
CDA4507,SPTE,T0.2,-,CDA4507,ABS+PC,5V,IV16,-,NORMAL CRT
DEL,SILICON V2,GRAY,-,-,-,NORMAL
BOX,6P,1R,2MM,ANGLE,SN
13P/14P,200MM,WHT/BLK/RED/BLU,UL1007,AWG26,SMH200-13/YBNH200-14
S1D2502A09-D0B0,DIP,32P,600MIL,PLASTIC,-,-,-20to75C,ST,52MM,AWG22(0.6PI),-,-,AWG22(0.
,80MM,BLK,1015,AWG22,-,-,-,-,DAWH-5NB,D15,L35,NTR,NYLON66
BWH,+,B,M3,L10,ZPC(YEL),SWRCH1
11P,22.5PI,26.5PI,NI,AA,3.5x1.0x5.7mm,1500,2375G
AA,3.5x1.0x5.7mm,1500,2375G
1uF,20%,50V,GP,TP,5x11,5
470uF,20%,16V,GP,TP,8x11.5,5
100nF,5%,100V,TP,11.5x12.5mm,5
100nF,+80-20%,50V,Y5V,TP,2.3X3
220uF,20%,16V,GP,-,6.3x11mm,2.
47uF,20%,100V,WT,TP,10x16,5
4.7uF,20%,50V,GP,TP,5x11,5
5.6nF,5%,100V,TP,10.5x12.5x6.5
1.8nF,10%,500V,Y5P,TP,8.5x3,5
1nF,5%,100V,TP,10.5x12.5x6.5,5
1nF,5%,100V,TP,10.5x12.5x6.5,5
0.33nF,10%,50V,Y5P,TP,4x3.5,5
1nF,10%,500V,Y5P,TP,7.5x3.5,5
1nF,10%,1kV,Y5P,TP,8x5,5
100nF,+80-20%,50V,Y5V,TP,2.3X3
10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5
10nF,5%,100V,TP,7x3.2x7mm,5mm
100nF,+80-20%,50V,Y5V,TP,8x3,5
100nF,+80-20%,50V,Y5V,TP,2.3X3
100nF,+80-20%,50V,Y5V,TP,2.3X3
100nF,+80-20%,50V,Y5V,TP,8x3,5
100nF,+80-20%,50V,Y5V,TP,8x3,5
1uF,20%,160V,WT,TP,3x11,5mm
100nF,5%,100V,TP,11.5x12.5mm,5
100nF,+80-20%,50V,Y5V,TP,2.3X3
0.1nF,5%,50V,SL,TP,5x3.5,5
0.27nF,10%,50V,Y5P,TP,4x3.5,5
0.015nF,5%,50V,NP0,TP,5x3,5
100nF,+80-20%,50V,Y5V,TP,8x3,5
100nF,+80-20%,50V,Y5V,TP,8x3,5
1uF,20%,160V,WT,TP,3x11,5mm
100nF,5%,100V,TP,11.5x12.5mm,5
100nF,+80-20%,50V,Y5V,TP,2.3X3
0.1nF,5%,50V,SL,TP,5x3.5,5
0.27nF,10%,50V,Y5P,TP,4x3.5,5
0.015nF,5%,50V,NP0,TP,5x3,5
100nF,+80-20%,50V,Y5V,TP,8x3,5
100nF,+80-20%,50V,Y5V,TP,8x3,5
1uF,20%,160V,WT,TP,3x11,5mm
100nF,5%,100V,TP,11.5x12.5mm,5
100nF,+80-20%,50V,Y5V,TP,2.3X3
0.1nF,5%,50V,SL,TP,5x3.5,5
0.27nF,10%,50V,Y5P,TP,4x3.5,5
0.015nF,5%,50V,NP0,TP,5x3,5
1N4148,100V,200mA,DO-35,TP
Remarks
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
7-11
7 Electrical Parts List
Loc. No.
DB01
DB02
DB03
DB04
DB05
DB06
DG01
DG02
DG03
DG04
DG05
DG06
DR01
DR02
DR03
DR04
DR05
DR06
EY1
EY2
EY3
EY4
G2
GND
JP103
JP109
JP116
JP117
JP119
JP122
JP123
JP124
JP127
JP128
JP133
JP134
JP136
JP137
JP140
JP142
JP147
JP148
JP150
JP151
JP152
L101
L103
LB01
LG01
LR01
MP1.3
Q102
QB01
QB02
QG01
QG02
QR01
QR02
R101
R102
R103
R104
R107
7-12
Code No.
Description
0401-000005
0401-000005
0401-000004
0401-000004
0401-000005
0401-000005
0401-000005
0401-000005
0401-000004
0401-000004
0401-000005
0401-000005
0401-000005
0401-000005
0401-000004
0401-000004
0401-000005
0401-000005
6042-000002
6042-000001
6042-000001
6042-000002
BH71-40300A
BH71-40300A
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
BH39-40305U
2701-000112
2701-000164
2701-000172
2701-000172
2701-000172
BH41-00058A
0501-000122
0501-000140
0501-000138
0501-000140
0501-000138
0501-000140
0501-000138
2001-000522
2001-000281
2001-001138
2001-001138
2001-000429
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
DIODE-SWITCHING
EYELET
EYELET
EYELET
EYELET
PIN-HINGE
PIN-HINGE
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
CBF HARNESS
INDUCTOR-AXIAL
INDUCTOR-AXIAL
INDUCTOR-AXIAL
INDUCTOR-AXIAL
INDUCTOR-AXIAL
PCB-VIDEO
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
TR-SMALL SIGNAL
R-CARBON
R-CARBON
R-CARBON(S)
R-CARBON(S)
R-CARBON
Specification
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1SS244,250V,625mA,DO-34,TP
1SS244,250V,625mA,DO-34,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1SS244,250V,625mA,DO-34,TP
1SS244,250V,625mA,DO-34,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
1SS244,250V,625mA,DO-34,TP
1SS244,250V,625mA,DO-34,TP
1N4148,100V,200mA,DO-35,TP
1N4148,100V,200mA,DO-35,TP
ID1.5,OD2,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID2.2,OD2.7,L3.1,SN,BSS3-E/EH
ID1.5,OD2,L3.1,SN,BSS3-E/EH
-,BRASS,D2.36,SN,HEAT/SINK
-,BRASS,D2.36,SN,HEAT/SINK
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
52MM,AWG22(0.6PI),-,-,AWG22(0.
100uH,10%,3x7mm
27uH,10%,4.2x9.8mm
330nH,10%,3x7mm
330nH,10%,3x7mm
330nH,10%,3x7mm
TP17LT,PHENOL,-,1.6T*247*330MM,2N3904,NPN,625mW,TO-92,TP,100-300
2N5551,NPN,625mW,TO-92,TP,80-250
2N5401,PNP,625mW,TO-92,TP,60-240
2N5551,NPN,625mW,TO-92,TP,80-250
2N5401,PNP,625mW,TO-92,TP,60-240
2N5551,NPN,625mW,TO-92,TP,80-250
2N5401,PNP,625mW,TO-92,TP,60-240
22KOHM,5%,1/8W,AA,TP,1.8X3.2MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
390OHM,5%,1/2W,AA,TP,2.4X6.4MM
390OHM,5%,1/2W,AA,TP,2.4X6.4MM
1KOHM,5%,1/8W,AA,TP,1.8X3.2MM
Remarks
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
PN17K*/PN17J*
7 Electrical Parts List
Loc. No.
Code No.
Description
R108
R109
R114
R115
R116
R117
R118
R119
R120
R123
R124
RB01
RB02
RB03
RB04
RB08
RB09
RB10
RB11
RB12
RB13
RB14
RB15
RB20
RG01
RG02
RG03
RG04
RG08
RG09
RG10
RG11
RG12
RG13
RG14
RG15
RG20
RR01
RR02
RR03
RR04
RR08
RR09
RR10
RR11
RR12
RR13
RR14
RR15
RR20
SK101
SK102
SKB01
SKG01
SKR01
2001-000812
2001-000563
2001-000780
2001-000577
2001-000290
2001-000734
2001-000857
2001-000857
2002-001022
2001-000432
2001-000034
2001-000969
2001-000969
2001-000780
2001-000281
2001-000793
2001-000962
2001-000705
2001-000281
2001-000449
2001-001000
2001-000780
2001-000793
2001-000947
2001-000969
2001-000969
2001-000780
2001-000281
2001-000793
2001-000962
2001-000705
2001-000281
2001-000449
2001-001000
2001-000221
2001-000793
2001-000947
2001-000969
2001-000969
2001-000780
2001-000281
2001-000793
2001-000962
2001-000705
2001-000281
2001-000449
2001-001000
2001-000780
2001-000793
2001-000947
1405-001064
4715-000001
4715-000102
4715-000102
4715-000102
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-COMPOSITION
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
R-CARBON
SURGE ABSORBER
SURGE ABSORBER
SURGE ABSORBER
SURGE ABSORBER
SURGE ABSORBER
5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM
27KOHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM
560OHM,5%,1/8W,AA,TP,1.8X3.2MM
560OHM,5%,1/8W,AA,TP,1.8X3.2MM
30MOHM,5%,1/4W,AA,TP,2.5X6.5MM
1MOHM,5%,1/4W,AA,TP,2.4X6.4MM
220OHM,5%,1/4W,AA,TP,2.4X6.4MM
75OHM,5%,1/8W,AA,TP,1.8X3.2MM
75OHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
47OHM,5%,1/8W,AA,TP,1.8X3.2MM
75KOHM,5%,1/4W,AA,TP,2.4X6.4MM
39OHM,5%,1/2W,AA,TP,3.3X9MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
82KOHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
47OHM,5%,1/8W,AA,TP,1.8X3.2MM
7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
75OHM,5%,1/8W,AA,TP,1.8X3.2MM
75OHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
47OHM,5%,1/8W,AA,TP,1.8X3.2MM
75KOHM,5%,1/4W,AA,TP,2.4X6.4MM
39OHM,5%,1/2W,AA,TP,3.3X9MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
82KOHM,5%,1/8W,AA,TP,1.8X3.2MM
1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
47OHM,5%,1/8W,AA,TP,1.8X3.2MM
7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
75OHM,5%,1/8W,AA,TP,1.8X3.2MM
75OHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
47OHM,5%,1/8W,AA,TP,1.8X3.2MM
75KOHM,5%,1/4W,AA,TP,2.4X6.4MM
39OHM,5%,1/2W,AA,TP,3.3X9MM
100OHM,5%,1/8W,AA,TP,1.8X3.2MM
2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
82KOHM,5%,1/8W,AA,TP,1.8X3.2MM
470OHM,5%,1/8W,AA,TP,1.8X3.2MM
47OHM,5%,1/8W,AA,TP,1.8X3.2MM
7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM
400V,20%,-,-,AXIAL
1KV,+50-10%,-,-,
200V,20%,1000A,-,RADIAL
200V,20%,1000A,-,RADIAL
200V,20%,1000A,-,RADIAL
HS103
CIS
CIS
CIS
CIS
BH99-00004B
6006-001008
6021-000118
BH13-00003A
BH62-00006A
ASSY,HEAT/SINK
SCREW-ASS’Y MACH
NUT-HEXAGON
IC-HYBRID
HEAT SINK-VIDEO
H/S VIDEO,SCREW+NUT,LM2437,-,-,OIL SILICON,-,WSP,BH,+,M3,L10,ZPC(YEL),SWRCH
1C,M3,ZPC(YEL),SM20C
-,LM2437,TO-220,9P,CRT DRIVER,0 TO 6.0V,-,A1050S T2.0,-,DB
PN17K*/PN17J*
Specification
Remarks
SNA
SNA
SNA
SNA
SNA
SNA
SNA
7-13
7 Electrical Parts List
7-3 Others
Loc. No.
Code No.
CRT
ASS`Y PBA UNIT
B/C ASS`Y CODE
(PN17K*)
(PN17J*)
(PN17K*)
(PN17K*)
(PN17J*)
(PN17J*)
S/CABLE
DEGAUSSING
MAGNET
BH03-00024D
BH94-00210A
BH94-00228A
BH98-00193A
BH98-00194A
BH98-00207A
BH98-00208A
BH39-00145A
BH27-00047A
BH27-00054A
3302-000006
Description
CRT-SF
ASSY PCB
ASSY PCB-SC
ASSY PCB/MAIN
ASSY PCB/VIDEO
ASSY PCB/MAIN-SC
ASSY PCB/VIDEO-SC
CBF SIGNAL
COIL-DEGAUSSING
COIL DEGAUSSING-ASS’Y
MAGNET-RUBBER
Specification
Remarks
M41QCJ761X172(P/5),96,17,0.25,-,29.1,FST,H/C,NH,-,FILM,TILT,4
PN17KT-07C1/4343,-,-,PN17KT,-,-,PN17KT-07C1/4343,-,-,PN17KT-07C1/4343,-,-,PN17JT,-,-,PN17JT,-,-,ATT,1500MM,15P/6P,7P,IVORY(IV01),-,D-SUB/MALE
320*250*1100mm,9.6mH,-,100Ts,°æ10%
320*250*1100mm,9.6mH,-,100Ts,°æ10%
AF,14G,1620-1980G,0.58-0.9MGOe
SNA
SNA
SNA
SNA
SNA
SNA
SNA
SNA
7-4 Different Part List (PN17JT/JO)
MAIN
Loc.No
85KHZ
R219
R455
R456
R457
R526
R527
ZD206
ZD207
C431
C437
C441
C442
C443
C444
HS403
JP66
JP71
JP72
D406
D430
Q420
Q421
7-14
Code-No
BH39-40305U
2001-000290
2001-000449
2001-000290
2001-000786
2001-000766
2001-000786
2301-001259
2301-001259
2401-000603
2301-001249
2303-000122
2303-000122
BH99-00005G
BH39-40305U
0402-001313
0402-000006
0501-000586
0505-001309
VIDEO
Specification
CBF HARNESS;52MM,AWG22(0.6PI),-,-,AWG22(0.
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;47KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;43KOHM,5%,1/8W
R-CARBON;47KOHM,5%,1/8W
C-FILM,MPPF;100nF,5%,400V,TP,19x8x16,7.5mm
C-FILM,MPPF;100nF,5%,400V,TP,19x8x16,7.5mm
C-AL;1uF,20%,50V,GP,TP,5x11,5
C-FILM,MPPF;68nF,5%,400V,TP,19x7x15mm,7.5
C-FILM,PPF;10nF,5%,630V,TP,19x12.5mm,7.5m
C-FILM,PPF;10nF,5%,630V,TP,19x12.5mm,7.5m
ASSY,HEAT/SINK;HSTR,SPRING,IRF740A,-,-,O
CBF HARNESS;52MM,AWG22(0.6PI),-,-,AWG22(0.
Loc.No
Code-No
HS103
LB01
LG01
LR01
RB08
RB13
RB14
RG08
RG13
RR08
RR13
RR14
A+A1
B+B1
C+C1
C119
BOTTOM
BH99-00004C
2701-001063
2701-001063
2701-001063
2001-000019
2001-000273
2001-000025
2001-000019
2001-000273
2001-000019
2001-000273
2001-000025
BH39-40306C
BH39-40306C
BH39-40306C
BH39-40361A
Specification
ASSY,HEAT/SINK;HS VIDEO,SCREW+NUT,LM2435,-,INDUCTOR-AXIAL;150nH,10%,3x7mm
INDUCTOR-AXIAL;150nH,10%,3x7mm
INDUCTOR-AXIAL;150nH,10%,3x7mm
R-CARBON(S);10OHM,5%,1/2W,AA,TP,2.4X6.4MM
R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;75OHM,5%,1/4W,AA,TP,2.4X6.4MM
R-CARBON(S);10OHM,5%,1/2W,AA,TP,2.4X6.4MM
R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON(S);10OHM,5%,1/2W,AA,TP,2.4X6.4MM
R-CARBON;100KOHM,5%,1/8W,AA,TP,1.8X3.2MM
R-CARBON;75OHM,5%,1/4W,AA,TP,2.4X6.4MM
CBF-HARNESS;,60MM,BLK,1015,AWG22,-,-,-,-,CBF-HARNESS;,60MM,BLK,1015,AWG22,-,-,-,-,CBF-HARNESS;,60MM,BLK,1015,AWG22,-,-,-,-,CBF-HARNESS;-,40MM,BLK,UL 1015,AWG22,-
DIODE-RECTIFIER;ERD07-15AL,1.7VK,1.5A,-,BK
DIODE-RECTIFIER;1N4007GP,1000V,1A,DO-41,TP
TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,TP,12
FET-SILICON;IRF630,N,200V,10A,0.4OHM,100W,TO
PN17K*/PN17J*
PN17K*/PN17J*
AC INPUT
SOCKET
CN601
ON THE CRT
TO D-COIL
LINE
FILTER
L601
DEGAUSSING
BLOCK
RL601
24LC04
EPROM
IC202
MCU
IC201
H/V SYNC
VIDEO INPUT
FRONT CONTROL
BOARD
LED
POWER
UP, DOWN
BRIGHTNISS
CONTRASTER
PIN, TRAP
SIZE, POSI,
DEGA.
SIGNAL
RETIFIER
BRIDGE
POWER
PWM CONTROL
IC601C
TILT
V-MUTE
S-CORRECTION
REF- OFF
BB
HOR. LINEARITY
REG.
12C DATA
12C CLK
H-SYNC1
V-SYNC1
E/W_OUT
H-SYNC, V-SYNC
MAIN BOARD
SWITCHING
TRANS
T601
KSC945
VER. BLANKING
Q303
HOR./VER.
PROCESSOR
IC401
TDA4859
VIDEO PRE-AMP
+ OSD
IC101(KA2506)
IC104(KA2501)
VIDEO BOARD
+12V
HOR. OUT
Q404
HEATER VOLTAGE CONTROL
+6.3V
Heater Switching
Q610
VER.OUT & TILT CONTORL
+12V REGULATOR
TO VIDEO
S-COR.
KSC5802
H. D. T
T401
VER. DY
CN401
SOCKET
-12V
+13V
+56V
+70V
FROM MCU
HOR. DRIVE
Q403
VER. OUTPUT
IC301
KA2142
HEATER
G1
RGB - CUTOFF
QR, G,B01,02
VIDEO OUTPUT
IC103(LM2437)
REF-OFF(From MCU)
CRT HEATER
BB(From MCU)
G1
DYNAMIC FOCUS
T502
HOR. DY
CN401
VERTICAL
FOCUS
FROM IC401
H/V SIZE
REG.
RGB
ACL
CIRCUIT
B(+)
FBT
T501
S
C
R
E
E
N
-210V
(FROM FBT)
BRIGHTNESS
CONTROL
CONTRAST
CONTROL
F
O
C
U
S
CONTROL
BRIGHTNESS
CONTROL
CONTRAST
+12V
+30V
-210V
H/V
8 Block Diagrams
8-1
8 Block Diagrams
Memo
8-2
PN17K*/PN17J*
9 Wiring Diagram
MAIN PCB
CRT SOCKET PCB
CRT SOCKET
FOCUS1 (WHT)
FOCUS2 (RED)
G2
2 x 3p DY 15"/17"
H+ (RED) H+
NC (BLUE) H(YEL) V+
H–
NC (BROWN)V-
1
1
2
3
4
2
3
4
(YEL)V+ 1
NC 2
(Brown)V – 3
1
2
3
2 x 3p DY
15"/17"
H + H + CN401
H– NC CN402
V + H– CN302
V–
NC CN303
1
2
V +
NC
V–
CN301
1
1
2
2
AC INPUT
AC
AC
1
AC INPUT
2
NC
3
AC INPUT
V+
V–
GT601
GT602
FOCUS
(WHT)
CN102
CN201
70 V
GND
6.3 V
G1
GND
12 V
V-SYNC
ACL
IICDATA
IICCLK
CLAMP
5V
AFC
DEGAUSSING COIL
AC
AC
CN501
FBT
1
1
2
3
4
5
6
7
8
9
2
3
4
5
6
7
8
9
10
11
12
13
10
11
12
13
14
CN601
70 V
GND
6.3 V
BLANK
G1
GND
12 V
V-SYNC
ACL
IICDATA
IICCLK
CLAMP
5V
AFC
CN203
1
KEY 1
GND
SW201 SW202 SW203 SW204
2
CN202
CN101
1
SIGNAL CABLE
1
GND
H-IN
V-IN
DDC DATA
DDC CLK
S-RASTER
DDC 5V
1 R_IN
2 GND_R
3 G_IN
4 GND_G
5 B_IN
6 GND_B
1
2
3
4
2
3
4
5
6
2
3
4
5
6
7
1 TILT+(WHT)
2 NC
TILT–(BLK)
3
5
6
7
TILT + 1
NC 2
TILT – 3
TILT
R
GND
G
GND
B
GND
GND
H-IN
V-IN
DDC DATA
DDC CLK
S-RASTER
DDC 5V
CN304
15 PIN
D-SUB
refer to pin
assignment
of
product spec.
PN17K*/PN17J*
9-1
9 Wiring Diagrams
Memo
9-2
PN17K*/PN17J*
10 Schematic Diagrams
10-1 Main Part Schematic Diagram
9
23
GT501
R516
D516
R531
V_REG_1
3
12
IC201
R526
T501
R527
R532
R507
C404
REG
D515
R530
CN501
R505
S4
18
11
R458
R410
L402
D431
4
C410
Q423
REG
R239
C408
Q402
C445
C447
R212
10
C406
R211
T502
C225
V_REG_1
R455
7 8
14
C448
13
C446
L403
Q420
S4
R456
R419
C442
D430
R420
C425
C430
C427
Q421
C417
C412
Q407
R459
L401
R443
C441 R457
C411
C435
D612
C443
HS403
C624
D407
BD401
BD402
C604
C444
Q422
Q608
C420
C421
C436
BD403
C419
D408
C621
C603
C613
R428
R425
D406
R431
Q404
D422
R444
D405
R432
D617
1
2
Q403
6
R427
5
PN17K*/PN17J*
10-1
10 Schematic Diagrams
1 100 V (IC601, #1)
2 100V (IC601, #1)
3 2.00 V (IC401, #6)
4 1.00V (IC401, #8)
5 20.0 V (Q403, Collector)
CH1 P-P = 100 V
CH1 P-P = 100V
CH1 P-P = 2.00V
CH1 P-P = 2.00V
CH1 P-P = 20.0 V
CH1 RMS = 350.2 V
CH1 RMS = 325.8 V
CH1 RMS = 5.868V
CH1 RMS = 5.868V
CH1 RMS = 46.80V
6 200 V (Q408, Collector)
7 1.00 V (IC401, #11)
8 500 V (IC401, #12)
9 10.0 V (IC301, #6)
10 2.00 V (Q402, Gate)
CH1 P-P = 200V
CH1 P-P = 1.00V
CH1 P-P = 500 V
CH1 P-P = 10.0 V
CH1 P-P = 2.00 V
CH1 RMS = 387.2V
CH1 RMS = 3.008 V
CH1 RMS = 1.425 V
CH1 RMS = 5.06 V
CH1 RMS = 7.692V
11 50.0 V (Q402, Drain)
12 2.00 V (IC401, #32)
13 50.0 V (T502, #6)
14 100 V (T502, #1)
18 1.00 V (IC201, #13, 14)
CH1 P-P = 50.0 V
CH1 P-P = 2.00V
CH1 P-P = 50.0V
CH1 P-P = 100V
CH1 P-P = 1.00 V
CH1 RMS = 73.7V
CH1 RMS = 6.124V
CH1 RMS = 75.6V
CH1 RMS = 124.0V
CH1 RMS = 2.108V
23 5.00V (Q303, Collector)
CH1 P-P = 5.00V
10-2
CH1 RMS = 28.33V
PN17K*/PN17J*
10 Schematic Diagrams
10-2 Video Part Schematic Diagram
19
20
24
16 21
22
15
17
PN17K*/PN17J*
10-3
10 Schematic Diagrams
15 1.00V (IC101 #5, 6, 7)
16 1.00V (IC101 #18,19,20)
17 20.0V (IC103, #1, 2, 3)
19 1.00 V (IC104, #6)
20 1.00 V (IC104, #8)
CH1 P-P = 1.00V
CH1 P-P = 1.00V
CH1 P-P = 20.0V
CH1 P-P = 1.00V
CH1 P-P = 1.00V
CH1 RMS = 2.452V
CH1 RMS = 2.792V
CH1 RMS = 40.52V
21 1.00 V (IC101, #18,19,20)
22 10.0 V (R,G,B, Video)
24 20.00V (CRT Socket, G1)
CH1 P-P = 1.00V
CH1 P-P = 10.0V
CH1 P-P = 20.0V
10-4
CH1 RMS = 2.580V
CH1 RMS = 17.02V
CH1 RMS = 4.516V
CH1 RMS = 5.024V
CH1 RMS = 66.68V
PN17K*/PN17J*