Download User`s Manual - Logic Supply

RT130
Ivy Bridge Rugged In-Vehicle Computer
User’s Manual
Version 1.1
2013.08
1
Preface
User Manual
Copyright
No part of this publication may be reproduced, transcribed, stored in a
retrieval system, translated into any language, or transmitted in any form or
by any means such as electronic, mechanical, magnetic, optical, chemical,
photocopy, manual, or otherwise, without prior written permission from
Logic Supply.
Other brands and product names used herein are for identification
purposes only and may be trademarks of their respective owners.
Disclaimer
Logic Supply shall not be liable for any incidental or consequential
damages resulting from the performance or use of this product.
Logic Supply makes no representation or warranty regarding the content of
this manual. Information in this manual had been carefully checked for
accuracy; however, no guarantee is given as to the correctness of the
contents. For continuing product improvement, Logic Supply reserves the
right to revise the manual or make changes to the specifications of this
product at any time without notice and obligation to any person or entity
regarding such change. The information contained in this manual is
provided for general use by customers.
This device complies to Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must withstand any background interference including those
that may cause undesired operation.
- 1-
Preface
Safety Information
Read the following precautions before setting up a Logic Supply Product.
Electrical safety
‡7RSUHYHQWHOHFWULFDOVKRFNKD]DUGGLVFRQQHFWWKHSRZHUFDEOHIURPWKH
electrical outlet before relocating the system.
‡:KHQDGGLQJRUUHPRYLQJGHYLFHVWRRUIURPWKHV\VWHPHQVXUHWKDWWKH
power cables for the devices are unplugged before the signal cables are
connected. If possible, disconnect all power cables from the existing
system before you add a device.
‡%HIRUHFRQQHFWLQJRUUHPRYLQJVLJQDOFDEOHVIURPWKHPRWKHUERDUG ensure that all power cables are unplugged.
‡6HHNSURIHVVLRQDODVVLVWDQFHEHIRUHXVLQJDQDGDSWHURUH[WHQVLRQFRUG
These devices could interrupt the grounding circuit.
‡0DNHVXUHWKDW\RXUSRZHUVXSSO\LVVHWWRWKHFRUUHFWYROWDJHLQ\RXU area. If you are not sure about the voltage of the electrical outlet you are
using, contact your local power company.
‡,IWKHSRZHUVXSSO\LVEURNHQGRQRWWU\WRIL[LWE\\RXUVHOI&RQWDFWD qualified service technician or your retailer.
Operation safety
‡%HIRUHLQVWDOOLQJWKHPRWKHUERDUGDQGDGGLQJGHYLFHVRQLWFDUHIXOO\UHDG
all the manuals that came with the package.
‡%HIRUHXVLQJWKHSURGXFWPDNHVXUHDOOFDEOHVDUHFRUUHFWO\FRQQHFWHG
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
‡7RDYRLGVKRUWFLUFXLWVNHHSSDSHUFOLSVVFUHZVDQGVWDSOHVDZD\IURP
connectors, slots, sockets and circuitry.
‡$YRLGGXVWKXPLGLW\DQGWHPSHUDWXUHH[WUHPHV'RQRWSODFHWKHSURGXFW
in any area where it may become wet.
‡3ODFHWKHSURGXFWRQDVWDEOHVXUIDFH
‡,I\RXHQFRXQWHUWHFKQLFDOSUREOHPVZLWKWKHSURGXFWFRQWDFWDTXDOLILHG
service technician or your retailer.
CAUTION
Incorrectly replacing the battery may damage this computer. Replace only
ZLWKWKHVDPHRULWVHTXLYDOHQWDVUHFRPPHQGHGE\/RJLF6XSSO\'LVSRVH
used battery according to the manufacturer's instructions.
- 2-
Preface
Table of contents page
(1) Introduction
0RGHO6SHFLILFDWLRQV 57,OOXVWUDWLRQ0DLQERDUG6\VWHP (2) Internal connector specification
9*$-67FRQQHFWRU 86%-67FRQQHFWRU 86%-67FRQQHFWRU *3,2-67FRQQHFWRU 8$57-67FRQQHFWRU /('-67FRQQHFWRU/('
/('-67FRQQHFWRU/('
&20SRUW-67FRQQHFWRU&20
&20SRUW-67FRQQHFWRU&20
$8',2-67FRQQHFWRU
6$7$3,1FRQQHFWRU6$7$
6$7$3,1FRQQHFWRU6$7$
6$7$3,1FRQQHFWRU6$7$
0,1,3&,(VORW0,1,&$5'
0,1,3&,(VORW0,1,&$5'
0,1,3&,(VORW0,1,&$5'
0,1,3&,(VORW0,1,&$5'
32:(5,1FRQQHFWRU
6$7$3RZHUFRQQHFWRU63:5
2.20 UPS Power connector
(3) External connector specification
86%7\SH$FRQQHFWRU
86%7\SH$FRQQHFWRU
5-FRQQHFWRU/$1
5-FRQQHFWRU/$1
5-FRQQHFWRU/$1
5-FRQQHFWRU/$1
'%FRQQHFWRU'9,,
'3FRQQHFWRU
'%FRQQHFWRU&20
- 3-
32
Preface
'%FRQQHFWRU&20 3+21(-$&.0,&,1 3+21(-$&./,1(287
$7;3,1FRQQHFWRU32:(5287
(4) System Installation
4.1 System Introduction
2SHQLQJ&KDVVLV ,QVWDOOLQJ0HPRU\ ,QVWDOOLQJ0,1,3&,H([SDQVLRQ&DUG3&,H*
0RGXOHRQO\
,QVWDOOLQJ0,1,3&,H([SDQVLRQ&DUG3&,H
,QVWDOOLQJ0,1,3&,H([SDQVLRQ&DUG3&,H
,QVWDOOLQJ0,1,3&,H([SDQVLRQ&DUG3&,H
3&,HRQO\
,QVWDOOLQJ,QWHUQDO$QWHQQD&DEOH ,QVWDOOLQJ6,0&DUG ,QVWDOOLQJ+''
,QVWDOOLQJ%DWWHU\0RGXOH (5) System Resources
,JQLWLRQ3RZHU0DQDJHPHQW4XLFN*XLGH
*3,2'HOD\7LPH6HWWLQJ
(6) BIOS
6.1 Super IO Configuration
- 4-
46
66
Preface
1.1 Model Specification
System
CPU
0emory
Chipset
/$1 Chipset
$XGio
:atchdog
Intel Gen 3 Core i7-3517UE 1.7GHz
Intel Gen 3 Core i3 3217UE
1.6GHz
Intel Gen 3 Celeron Dual Core 1047E 1.4GHz
1 x DDR3 1066/1333/1600 MHz-SO DIMM up to 8 GB
QM77
Intel I210
- AT Gb/s Ethernet Controllers Onboard
Support PXE and WOL
Realtek ALC662 HD Codec onboard
Watchdog Timer Support, Oīer 1 – 255 Step
Power Requirement
Power Input
9V-32V DC Power input
Power Protection
AutomaƟcs Recovery Short Circuit ProteĐƟon
Power 0anagement
Vehicle Power IgniƟon for Variety Vehicle
Power Off Control
%Dttery
Power oī Delay Time Seƫng by SoŌware
Internal BaƩery Kit for 10 Mins OperaƟng (OpƟonal
)
Storage
Type
2 x 2.5” Drive Bay for SATA Type HDD / SSD, Support RAID 0, 1
1 x SATA DOM
- 5-
Preface
Graphics
Graphics
Intel® HD Graphics 4000
DirectX Video AcceleraƟon (DXVA) for AcceleraƟng Video
Processing - Full AVC/VC1/MPEG2 HW Decode
Supports DirectX 11/10.1/10/9 and OpenGL 3.0
Resolution
Up to 1920 x 1200
QuaůŝĮcaƟon
Certifications
CE, FCC Class A, eMark
I/O
Serial Port
3 x RS-232 (COM1,2 with RS-422/485, RS-485 Support Auto Direction Control)
86% Port
4 x USB 3.0 Ports on Front I/O
L$1
4 x RJ45 Ports for GbE
Video Port
1 x DVI-I, 1 x VGA and 1 x Display Port Output
',O Port
4 in and 4 out with Relay 12V / 80mA
$XGio
1 x Line-out and 1 x MIC-in
SI0 Card Socket
2 x SIM Card sockets supported onboard with eject
Environment
Operating Temp.
-40ºC ~ 70ºC (Default CPU 17WaƩ)
Storage Temp.
-40 ~ 80ºC
Relative Humidity
0% RH– 95% RH
Vibration (random
2.5g@5~500 Hz with SSD
Vibration Operating
MIL-STD-810F, Method 514.5, Category 20,
Ground Vehicle-Highway
Truck Storage
MIL-STD-810F, Method 514.5, Category 24, Integrity Test
Shock
Crash Ha]ard
OperaƟng: MIL-STD-810F, Method 516.5, Procedure I,
Trucks and semi-trailers=40G (11ms) with SSD
MIL-STD-810F, Method 516.5, Procedure V,
Ground equipment=100
Mechanical
Construction
Aluminum alloy
0ounting
Supports both of wall-mount/VESA-mount
:eight
1.780 kg (bare-bone)
'imensions
250 x 150 x 55 mm
- 6-
Preface
1.2 RT130 Illustration
Mainboard
- -
Preface
System
- 8-
Preface
(2) Internal connector specification
2.1 VGA Connector
Connector 2 X 8 = 16 Pin
size
Connector JST-2.0mm-M-180
type
Connector VGA1
location
Connector
Pin
Signal
pin
1
RED
definition
3
BLUE
5
CER_DET
7
GND
9
+5V
11
NC
13
HSYNC
15
DAC_SCL
Connector map
- -
Pin
2
4
6
8
10
12
14
16
Signal
GREEN
NC
GND
GND
GND
DAC_SDA
VSYNC
NC
Preface
2.2 USB Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
2 X 4 = 8 Pin
JST-2.0mm-M-180
USB2 (Co-layout with DVI-I1)
Pin
1
3
5
7
Signal
5VSB
USB_7N
USB_7P
GND
Connector map
- 10 -
Pin
2
4
6
8
Signal
5VSB
NC
NC
GND
Preface
2.2 USB Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
2 X 4 = 8 Pin
JST-2.0mm-M-180
USB3 (Co-layout with MINICARD3)
Pin
1
3
5
7
Signal
5VSB
USB_6N
USB_6P
GND
Pin
2
4
6
8
Connector map
- 11 -
Signal
5VSB
NC
NC
GND
Preface
2.4 GPIO Connector
Connector
size
Connector
type
Connector
location
2 X 5 = 10 Pin
JST-2.0mm-M-180
GPIO1
Connector
pin
definition
Pin
1
3
5
7
9
Signal
GPI0
GPI2
GPO0
GPO2
GND
Connector map
- 12 -
Pin
2
4
6
8
10
Signal
GPI1
GPI3
GPO1
GPO3
+12V
Preface
2.5 UART Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
2 X 5 = 10 Pin
JST-2.0mm-M-180
UART1 (COM5 for GPS Module when installed )
Baud Rate : 9600
Pin
Signal
Pin
1
NC
2
3
COM5_TX
4
5
GND
6
7
NC
8
9
NC
10
Connector map
- 13 -
Signal
COM5_RX
NC
NC
GND
+5V
Preface
2.6 LED Connector
Connector
2 X 2 = 4 Pin
size
Connector
LED WITH HOUSING
type
Connector
LED1
location
Connector
Pin
Signal
pin
A1
3.5G_LED_P
definition
C1
3.5G_LED_N
Connector map
- 14 -
Pin
A2
C2
Signal
UPS_LED_P
UPS_LED_N
Preface
2.7 LED Connector
Connector
2 X 2 = 4 Pin
size
Connector
LED WITH HOUSING
type
Connector
LED2
location
Connector
Pin
Signal
pin
A1
ACC_LED_P
definition
C1
ACC_LED_N
Connector map
- 15 -
Pin
A2
C2
Signal
HDD_LED_P
HDD_LED _N
Preface
2.8 COM Connector
Connector
size
Connector
type
Connector
location
2 X 5 = 10 Pin
JST-2.0mm-M-180
COM3
Connector
pin
definition
Pin
1
3
5
7
9
Signal
COM3_DCD
COM3_TXD
GND
COM3_RTS
COM3_RI
Connector map
- 16 -
Pin
2
4
6
8
10
Signal
COM3_RXD
COM3_DTR
COM3_DSR
COM3_CTS
GND
Preface
2.9 COM Connector
Connector
size
Connector
type
Connector
location
2 X 5 = 10 Pin
JST-2.0mm-M-180
COM4
Connector
pin
definition
Pin
1
3
5
7
9
Signal
COM4_DCD
COM4_TXD
GND
COM4_RTS
COM4_RI
Connector map
- -
Pin
2
4
6
8
10
Signal
COM4_RXD
COM4_DTR
COM4_DSR
COM43_CTS
GND
Preface
2.10 COM Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
1 X 10 = 10 Pin
JST-2.0mm-M-180
AUDIO1
Pin
1
2
3
4
5
6
7
8
9
10
Signal
NC
NC
NC
NC
NC
NC
MIC_IN_ L
MIC_IN_R
MIC-JD
GND
Connector map
- 18 -
Preface
2.11 SATA Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
1 X 7 = 7 Pin
SATA 1.27mm-M-180D
SATA DOM1
Pin
1
2
3
4
5
6
7
Signal
GND
SATA_TXP2
SATA_TXN2
GND
SATA_RXN2
SATA_RXP2
GND
Connector map
- -
Preface
2.12 SATA Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
1 X 7 = 7 Pin
SATA 1.27mm-M-180D
SATA1
Pin
S1
S2
S3
S4
S5
S6
S7
Signal
GND
SATA_TXP0
SATA_TXN0
GND
SATA_RXN0
SATA_RXP0
GND
Connector map
- 20 -
Pin
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
Signal
NC
NC
NC
GND
GND
GND
+5V
+5V
+5V
NC
GND
GND
NC
NC
NC
Preface
2.13 SATA Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
1 X 7 = 7 Pin
SATA 1.27mm-M-180D
SATA2
Pin
S1
S2
S3
S4
S5
S6
S7
Signal
GND
SATA_TXP1
SATA_TXN1
GND
SATA_RXN1
SATA_RXP1
GND
Connector map
- 21 -
Pin
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
Signal
NC
NC
NC
GND
GND
GND
+5V
+5V
+5V
NC
GND
GND
NC
NC
NC
Preface
2.14 Mini PCI-E Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
2 X 26 = 52 Pin
MINI PCI-E CON 9.2mmH
MINICARD1
Pin
1
3
5
7
9
11
13
15
17
19
Signal
PCIE_WAKE#
NC
NC
MINICARD1_CLKREQ#
GND
NC
NC
GND
NC
NC
Pin
2
4
6
8
10
12
14
16
18
20
21
23
25
27
29
31
33
35
37
39
41
GND
NC
NC
GND
GND
NC
NC
GND
GND
3VSB
3VSB
22
24
26
28
30
32
34
36
38
40
42
43
45
GND
NC
44
46
47
49
51
NC
NC
NC
48
50
52
- 22 -
Signal
3VSB
GND
+1.5V
UIM_PWR
UIM_DAT
UIM_CLK
UIM_RST
NC
GND
MINICARD
1_DIS#
PCIE_RST#
3VSB
GND
+1.5V
SMB_CLK
SMB_DATA
GND
USB_4N
USB_4P
GND
LED_WWA
N#
LED_WAN#
LED_WPAN
#
+1.5V
GND
3VSB
Preface
Connector map
- 23 -
Preface
2.15 Mini PCI-E Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
2 X 26 = 52 Pin
MINI PCI-E CON 9.2mmH
MINICARD2
Pin
1
3
5
7
9
11
13
15
17
19
Signal
PCIE_WAKE#
NC
NC
MINICARD2_CLKREQ#
GND
PCIE_MCARD2_CLK_N
PCIE_MCARD2_CLK_P
GND
NC
NC
Pin
2
4
6
8
10
12
14
16
18
20
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
GND
PCIE_MCARD2_RX_N
PCIE_MCARD2_RX_P
GND
GND
PCIE_MCARD2_TX_N
PCIE_MCARD2_TX_P
GND
GND
3VSB
3VSB
GND
NC
NC
NC
NC
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
- 24 -
Signal
3VSB
GND
+1.5V
UIM_PWR
UIM_DAT
UIM_CLK
UIM_RST
NC
GND
MINICARD2_DIS
#
PCIE_RST#
3VSB
GND
+1.5V
SMB_CLK
SMB_DATA
GND
USB_5N
USB_5P
GND
LED_WWAN#
LED_WAN#
LED_WPAN#
+1.5V
GND
3VSB
Preface
Connector map
- 25 -
Preface
2.16 Mini PCI-E Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
2 X 26 = 52 Pin
MINI PCI-E CON 9.2mmH
MINICARD3
Pin
1
3
5
7
9
11
13
15
17
19
Signal
PCIE_WAKE#
NC
NC
MINICARD3_CLKREQ#
GND
PCIE_MCARD3_CLK_N
PCIE_MCARD3_CLK_P
GND
NC
NC
Pin
2
4
6
8
10
12
14
16
18
20
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
GND
PCIE_MCARD3_RX_N
PCIE_MCARD3_RX_P
GND
GND
PCIE_MCARD3_TX_N
PCIE_MCARD3_TX_P
GND
GND
3VSB
3VSB
GND
NC
NC
NC
NC
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
- 26 -
Signal
3VSB
GND
+1.5V
NC
NC
NC
NC
NC
GND
MINICARD3_DIS
#
PCIE_RST#
3VSB
GND
+1.5V
SMB_CLK
SMB_DATA
GND
USB_6N
USB_6P
GND
NC
NC
NC
+1.5V
GND
3VSB
Preface
Connector map
- -
Preface
2.17 Mini PCI-E Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
2 X 26 = 52 Pin
MINI PCI-E CON 9.2mmH
MINICARD4
Pin
1
3
5
7
9
11
13
15
17
19
Signal
PCIE_WAKE#
NC
NC
MINICARD4_CLKREQ#
GND
PCIE_MCARD4_CLK_N
PCIE_MCARD4_CLK_P
GND
NC
NC
Pin
2
4
6
8
10
12
14
16
18
20
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
GND
PCIE_MCARD4_RX_N
PCIE_MCARD4_RX_P
GND
GND
PCIE_MCARD4_TX_N
PCIE_MCARD4_TX_P
GND
GND
3VSB
3VSB
GND
NC
NC
NC
NC
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
- 28 -
Signal
3VSB
GND
+1.5V
NC
NC
NC
NC
NC
GND
MINICARD4_DIS
#
PCIE_RST#
3VSB
GND
+1.5V
SMB_CLK
SMB_DATA
GND
NC
NC
GND
NC
NC
NC
+1.5V
GND
3VSB
Preface
Connector map
- -
Preface
2.18 POWER Input Connector
Connector
size
Connector
type
Connector
location
1 X 4 = 4 Pin
WAFER 2.54mm-M-180
PWRIN1
Connector
pin
definition
Pin
1
2
3
Signal
GND
VIN (9-32V)
IGNITION
Connector map
- 30 -
Preface
2.19 SATA Power Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
1 X 4 = 4 Pin
WAFER 2.54mm-M-180
SPWR1
Pin
1
2
3
4
Signal
+5V
GND
GND
+12V
Connector map
- 31 -
Preface
2.20 UPS Power Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
1 X 4 = 4 Pin
WAFER 2.54mm-M-180
UPS1
Pin
1
2
3
4
Signal
+12V
+12V
GND
GND
Connector map
- 32 -
Preface
(3) External Connector Specification
3.1 USB Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
8 Pin
USB3.0 Type A
USB3
Pin
1
3
5
7
9
11
13
15
17
Signal
5VSB
USB0_P
SSRX0_ON
GND
SSTX0_OP
USB1_N
GND
SSRX1_OP
SSTX1_ON
Connector map
- 33 -
Pin
2
4
6
8
10
12
14
16
18
Signal
USB0_N
GND
SSRX0_OP
SSTX0_ON
5VSB
USB1_P
SSRX1_ON
GND
SSTX1_OP
Preface
3.2 USB Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
8 Pin
USB3.0 Type A
USB4
Pin
1
3
5
7
9
11
13
15
17
Signal
5VSB
USB2_P
SSRX2_ON
GND
SSTX2_OP
USB3_N
GND
SSRX3_OP
SSTX3_ON
Connector map
- 34 -
Pin
2
4
6
8
10
12
14
16
18
Signal
USB2_N
GND
SSRX2_OP
SSTX20_ON
5VSB
USB3_P
SSRX3_ON
GND
SSTX3_OP
Preface
3.3 LAN Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
12 Pin
RJ45+LED
LAN1
Pin
1
3
5
7
9
Signal
LAN0_MDI0P
LAN0_MDI1P
LAN0_MDI2N
LAN0_MDI3P
LAN0_ACT#
Pin
2
4
6
8
10
11
LAN0_LINK#
12
Connector map
- 35 -
Signal
LAN0_MDI0N
LAN0_MDI2P
LAN0_MDI1N
LAN0_MDI3N
LAN0_ACTP
W
LAN0_LINKP
W
Preface
3.4 LAN Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
12 Pin
RJ45+LED
LAN2
Pin
1
3
5
7
9
11
Signal
LAN1_MDI0P
LAN1_MDI1P
LAN1_MDI2N
LAN1_MDI3P
LAN1_ACT#
LAN1_LINK#
Connector map
- 36 -
Pin
2
4
6
8
10
12
Signal
LAN1_MDI0N
LAN1_MDI2P
LAN1_MDI1N
LAN1_MDI3N
LAN1_ACTPW
LAN1_LINKPW
Preface
3.5 LAN Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
12 Pin
RJ45+LED
LAN3
Pin
1
3
5
7
9
11
Signal
LAN2_MDI0P
LAN2_MDI1P
LAN2_MDI2N
LAN2_MDI3P
LAN2_ACT#
LAN2_LINK#
Connector map
- -
Pin
2
4
6
8
10
12
Signal
LAN2_MDI0N
LAN2_MDI2P
LAN2_MDI1N
LAN2_MDI3N
LAN2_ACTPW
LAN2_LINKPW
Preface
3.6 LAN Connector
Connector
size
Connector
type
Connector
location
Connector
pin
definition
12 Pin
RJ45+LED
LAN4
Pin
1
3
5
7
9
11
Signal
LAN3_MDI0P
LAN3_MDI1P
LAN3_MDI2N
LAN3_MDI3P
LAN3_ACT#
LAN3_LINK#
Connector map
- 38 -
Pin
2
4
6
8
10
12
Signal
LAN3_MDI0N
LAN3_MDI2P
LAN3_MDI1N
LAN3_MDI3N
LAN3_ACTPW
LAN3_LINKPW
Preface
3.7 DVI-I Connector
Connector 50 Pin
size
Connector DVI-I
type
Connector DVI-I1
location
Connector
pin
definition
Pin
1
3
5
7
9
11
13
15
17
19
21
23
C1
C3
C5
Signal
DVI_TX2_N
GND
+12V
DVI_DDC_DATA
DVI_TX1_N
GND
USB_7P
GND
DVI_TX0_N
GND
CRT_DAC_SCL
DVI_CLK_P
CRT_RED
CRT_BLUE
CRT_DET
Connector map
- -
Pin
2
4
6
8
10
12
14
16
18
20
22
24
C2
C4
C6
Signal
DVI_TX2_P
5VSB
DVI_DDC_CLK
CRT_VSYNC
DVI_TX1_P
USB_7N
+5V
DVI_HPD
DVI_TX0_P
CRT_DAC_SDA
NC
DVI_CLK_N
CRT_GREEN
CRT_HSYNC
GND
Preface
3.8 DP Connector
Connector 20 Pin
size
Connector Display port
type
Connector DP1
location
Connector
Pin
pin
1
definition
3
5
7
9
11
13
15
17
19
Connector
map
Signal
DP2_LANE_0P
DP2_LANE_0N
GND
DP2_LANE_2P
DP2_LANE_2N
GND
DP2_AUX_EN#
DP2_AUXP_CLK
DP2_AUXN_DATA
GND
- 40 -
Pin
2
4
6
8
10
12
14
16
18
20
Signal
GND
DP2_LANE_1P
DP2_LANE_1N
GND
DP2_LANE_3P
DP2_LANE_3N
GND
GND
DP2_HPD
DP2_VCC3
Preface
3.9 COM Connector
Connector 9 Pin
size
Connector DSUB
type
Connector COM1
location
Connector
pin
definition
Pin
1
3
5
7
9
Signal
COM1_DCD /
(RS-485_TXD-/RXD-)
COM1_TXD
GND
COM1_RTS
COM1_RI#
Connector map
- 41 -
Pin
2
4
6
8
Signal
COM1_RXD
(RS-485_TXD+/RXD+)
COM1_DTR
COM1_DSR
COM1_CTS
Preface
3.10 COM Connector
Connector 9 Pin
size
Connector DSUB
type
Connector COM2
location
Connector
pin
definition
Pin
1
3
5
7
9
Signal
COM2_DCD
(RS-485_TXD-/RXD-)
COM2_TXD
GND
COM2_RTS
COM2_RI#
Connector map
- 42 -
Pin
2
4
6
8
Signal
COM2_RXD
(RS-485_TXD+/RXD+)
COM2_DTR
COM2_DSR
COM2_CTS
Preface
3.11 MIC Connector
Connector 6 Pin
size
Connector Phone Jack
type
Connector MIC1
location
Connector
Pin
pin
1
definition
3
5
Connector map
Signal
MIC_OUT-L
NC
GND
- 43 -
Pin
2
4
6
Signal
MIC-JD
MIC_OUT-R
GND
Preface
3.12 LINE OUT Connector
Connector 6 Pin
size
Connector Phone Jack
type
Connector LOUT1
location
Connector
Pin
pin
1
definition
3
5
Connector map
Signal
FRONT_OUT_L
NC
GND
- 44 -
Pin
2
4
6
Signal
FRONT-JD
FRONT_OUT_R
GND
Preface
3.13 POWER OUT Connector
Connector 6 Pin
size
Connector ATX 6PIN
type
Connector PWROUT1
location
Connector
pin
definition
Pin
1
3
5
Signal
+12V
EXT_DI1
GND
Connector map
- 45 -
Pin
2
4
6
Signal
+12V
GND
EXT_DI2
Preface
4.1 System Introduction
GPS Antenna SIM Card2
LAN1
LAN2
LAN3
LAN4
USB3.0
SIM Card1
LED
Power Button
2.5" Storage Bay
WiFi/BT Antenna COM3
MIC Line Out
DIO
COM1
COM4/VIDEO IN
COM2
12V OUTPUT
- 46 -
DP
3G Antenna
VGA
DVI-I
WiFi/BT Antenna
DC IN
Preface
4.2 Opening Chassis
Step 1. Unscrew the six screws of the
%DFN&RYHUDVVKRZQLQ
the picture.
Step 2. Unscrew the six screws of
the Front Panel as shown in
the picture.
Step 3. Unscrew the six screws of
the Rear Panel as shown in
the picture.
Step 4. Open Top Cover as shown in
the picture.
- -
Preface
4.3 Installing Memory
Step 1.3XW0HPRU\RQWKLVSODFHDVVKRZQ
in the picture.
Step 2.+ROGWKH0HPRU\ZLWKLWVQRWFK
DOLJQHGZLWKWKH0HPRU\VRFNHWRI
the board and insert it at a 30-degree
angle into the socket as shown in
the picture.
Step 3.3UHVVGRZQRQWKH0HPRU\VRWKDW
the tabs of the socket lock on both
sides of the module as shown in the
picture.
- 48 -
Preface
4.4 Installing MINI PCIe Expansion Card (PCIe 1, 3G Module only)
Step 1.3XW0,1,3&,H([SDQVLRQ&DUG
on this place as shown in the
picture.
Step 2.+ROGWKH0RGXOHZLWKLWVQRWFK
aligned with the socket of the
board and insert it at a 30
degree angle into the socket as
shown in the picture.
Step 3. Screw two screws to the holder
as shown in the picture.
Step 4.'RQHDVVKRZQLQWKH
picture.
- -
Preface
4.5
Installing MINI PCIe Expansion Card (PCIe 2)
Step 1.3XW0,1,3&,H([SDQVLRQ&DUG
on this place as shown in the
picture.
Step 2.+ROGWKH0RGXOHZLWKLWVQRWFK
aligned with the socket of the
board and insert it at a 30
degree angle into the socket as
shown in the picture.
Step 3. Screw two screws to the holder
as shown in the picture.
Step 4.'RQHDVVKRZQLQWKH
picture.
- 50 -
Preface
4.6 Installing MINI PCIe Expansion (PCIe 3)
Step 1.3XW0,1,3&,H([SDQVLRQ&DUG
on this place as shown in the
picture.
Step 2.+ROGWKH0RGXOHZLWKLWVQRWFK
aligned with the socket of the
board and insert it at a 30
degree angle into the socket as
shown in the picture.
Step 3. Screw two screws to the holder
as shown in the picture.
Step 4.'RQHDVVKRZQLQWKH
picture.
- 51 -
Preface
4.7 Installing MINI PCIe Expansion (PCIe 4, PCIe only)
Step 1.3XW0,1,3&,H([SDQVLRQ&DUG
on this place as shown in the
picture.
Step 2.+ROGWKH0RGXOHZLWKLWVQRWFK
aligned with the socket of the
board and insert it at a 30
degree angle into the socket as
shown in the picture.
Step 3. Screw two screws to the holder
as shown in the picture.
Step 4.'RQHDVVKRZQLQWKH
picture.
- 52 -
Preface
4.8 Installing Internal Antenna Cable
Step 1.7DNHWKH60$&RQQHFWRUDQG
Plug into IO Panel as shown in
the picture.
Step 2.3XWWKH:DVKHULQWRWKH60$
Connector as shown in the
picture.
Step 3.3XWWKH2ULQJWR60$&RQQHFWRU
and tighten as shown in the
picture.
Step 4.'RQHDVVKRZQLQWKHSLFWXUH
- 53 -
Preface
Step 5. Take the Ipex Connector and
Step 6. Take the Ipex Connector and
press on the 3G module as
VKRZQLQWKHSLFWXUH*
Step 7. Take the Ipex Connector and
press on the GPS module as
shown in the picture. (GPS,
RQO\VXSSRUWSDVVLYH$QWHQQD
- 54 -
Preface
4.9 Installing SIM Card
Step 1. Use thin stick to push the button
as shown in the picture.
Step 2. Take the holder away from
front panel as shown in the
picture.
Step 3.3XW\RXU6,0&DUGLQWRWKHKROGHU
as shown in the picture.
Step 4. TDNHWKH6,0FDUGKROGHUDQG
Insert it into the socket as
shown in the picture.
- 55 -
Preface
4.10 Installing HDD
Step 1.3XWWKH+''LQWR+''+ROGHU
as shown in the picture.
Step 2. Screw two screws on both side
as shown in the picture.
Step 3.3XVKWKH+''+ROGHULQWRWKH
socket as shown in the picture.
- 56 -
Preface
Step 4.)XOO\LQVHUWWKH+''+ROGHULQWR
the socket until a “click” is heard
as shown in the picture.
Step 5.7LJKWHQWR6WRUDJH%UDFNHW
screws as shown in the picture.
- -
Preface
4.11 Installing Battery Module
Step 1.$FFHVVRULHVOLVW
Step 2.)L[WKH7XEHZLWK6FUHZ$
on the motherboard
Step 3.)L[WKH7XEHZLWK6FUHZ$
to another hole.
Step 4.)L[WKH6FHZ$IURPEDFN
side
- 58 -
Preface
Step 5. Tube Location check.
Step 6. Connect the battery with
motherboard on UPS location.
Step 7.)L[WKHEDWWHU\ZLWK6FUHZ%
'RQH
- -
Preface
(5) System Resources
5.1 Ignition Power Management Quick Guide
Startup/shutdown conditions from the IGNITION signal:
- IGNITION startup signal must be valid during 3 sec. (anti noise
SURWHFWLRQ
- IGNITION shutdown – IGNITION signal must be inactive during 3 Sec,
then PIC controller initiate Power
%XWWRQVLJQDO26PXVWEHVHWWRVKXWGRZQIURPWKH3RZHU%XWWRQ,W
JHQHUDWHV0DLQ%XWWRQVKXWGRZQHYHQWDQGWKHQJRHVWRFRPSOHWH power off.
Typically the system can start only from IGNITION signal, because startup
PIC controller is disconnected from the power source.
The system can be switched off from:
- Power IGNITION OFF signal.
$&3,26VKXWGRZQ
- 3RZHU%XWWRQ±JHQHUDWH$&3,HYHQW26GHSHQGHQW
12V or 24V
Power Input
Check IGN
Status
IGN on (High)
more than 3sec
Power Ignition Startup Procedure
- 60 -
System Turn on
Preface
Delay Time Off
Delay 3 Sec
Check IGN
Status
IGN off (Low)
Check Delay
Time
Shutdown from OS
& IGN off
OS Shutdown System
Delay Time On
3 sec later
0-99 Minutes
System Power off
Setting by Software
Power Ignition Shutdown Procedure
Power Management
- Power-off delay time is selectable by Software to disable and enable in
PLQXWHV
-,JQLWLRQ2Q2IIVWDWXVGHWHFWDEOHE\6:
- If the ignition is off and the system is still on after 3 Sec, RT130 will shut
down automatically.
- If the ignition is turned on again and the power-off delay is in progress,
RT130 will cancel the delay function and will continue to operate normally.
- If the ignition is turned on again and the power-off delay ended, RT130
will shut down completely will power-on again automatically.
- 61 -
Preface
5.2 GPIO & Ignition Register
5.2.1 GPIO and Ignition Control Register
The General Purpose I/O is an interface available on some devices. These can
read digital signals from other parts of a circuit, or output to control other devices.
$W*3,2FRQWUROUHJLVWHUWKH*3,LVXVHWRUHFHLYHGDWDWKH*32LVVHWGDWDWR
send.
I/O port: [$EDVHDGGUHVVIRU&RQWURO5HJLVWHU5HDG[$K:ULWH[$K
[$EDVHDGGUHVVIRU&RQWURO'DWD9DOXH
'HEXJ&RPPDQG/LQH
2$$
2$)6HW%LWWR/RZ
6
DO4
5
DO3
4
DO2
3
DO1
2
DI4
1
DI3
0 = DI is low *
1 = DI is high
0 = DO is low
1 = DO is high *
- 62 -
0
DI2
DI1
Preface
- 63 -
Preface
I/O port: I/O port: 0xA35 (base address) for Control Register (Read 0xF2h bit 3)
0xA36 (base address) for Control Data Value
7
X
6
X
5
X
4
X
3
Ignition
Status
2
X
1
X
0
X
0 = Ignition off
1 = Ignition on
Debug Command Line
-
O A35 F2
-
I A36
// Check Bit 3 Status
5.2.2 WDT Setting
I/O port: A10 (base address) + 05h and 06h
1 Watchdog Timer Control Register
The :atchdog Timer Control Register controls the :'T working mode. :Uite the value to the
:'T Configuration Port. The following table describes the Control Register bit definition:
7
0
6
0
5
1
4
1
3
Timer
Unit
0 = 1 sec
1 = 60 sec *
Debug Command Line
-
O A16 05
-
O A15 32
// 5 sec // 3A
2
0
1
0
Select output pulse
width of RSTOUT#
00 = 1 ms
01 = 25 ms
10 = 125 ms*
11 = 5 sec
5 minutes
- 64 -
Preface
- 65 -
Preface
( 6 ) BIOS
6.1 Super IO Configuration
Select Serial Port0ode
- 66 -