Download User`s Manual - CBC (Europe)

PixelPro Series
ZN-BxMTP Series User’s Manual
ZN-B2MTP / ZN-B2MTP-2 / ZN-B1MTP
1
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
that produce heat.
9) Only use the attachments/accessories specified by the manufacturer.
10) Use only with a cart, stand, tripod or bracket specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
12) Unplug this apparatus during lightning storms or when unused for long periods of time.
13) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
WARNING:
・To reduce the risk of fire or electric shock, do not expose this apparatus especially
connections part to rain or moisture.
・The apparatus shall not be exposed to dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on the apparatus.
2
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric
shock does not perform any servicing other than that contained in the operating instructions unless you are
qualified to do so.
In USA and Canada, Use Class 2 Power Supply Only
3
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
Contents
1. PRODUCT FEATURES ........................................................................................................................... 6
2. ACCESSING THE CAMERA .................................................................................................................. 11
2.1 ACCESS FROM A BROWSER ................................................................................................................... 11
2.2 ACCESSING THE CAMERA FROM THE INTERNET...................................................................................... 12
2.3 ADJUSTING THE IMAGE AND FOCUS ...................................................................................................... 12
2.4 THE LIVE VIEW PAGE ........................................................................................................................... 12
2.5 VIDEO STREAM TYPES ......................................................................................................................... 13
2.6 HOW TO STREAM H.264 ...................................................................................................................... 13
3. THE SETUP ........................................................................................................................................... 14
4. ANALOG OUTPUT ............................................................................................................................... 15
4.1 ANALOG OUTPUT SETUP ..................................................................................................................... 15
5. VIDEO .................................................................................................................................................... 15
5.1 CODEC ............................................................................................................................................... 15
5.2 CAMERA ............................................................................................................................................. 18
5.2.1 Exposure Control ....................................................................................................................... 18
5.2.2 Day & Night Control ................................................................................................................... 19
5.2.3 White Balance Control ............................................................................................................... 20
5.2.4 Image Property Control .............................................................................................................. 20
5.2.5 Lens Adjustment ....................................................................................................................... 20
6. AUDIO .................................................................................................................................................... 21
7. LIVE ....................................................................................................................................................... 22
7.1 SETUP .............................................................................................................................................. 22
7.2 PRIVACY MASKING............................................................................................................................ 23
8. SD CARD ............................................................................................................................................... 24
8.1 CONFIGURATION ................................................................................................................................. 24
8.2 EVENT ................................................................................................................................................ 25
8.3 PERIODICAL ........................................................................................................................................ 26
9. FTP......................................................................................................................................................... 27
9.1 FTP > CONFIG .................................................................................................................................... 27
9.2 FTP > EVENT ..................................................................................................................................... 27
9.3 FTP > PERIODICAL ............................................................................................................................. 28
10. EVENT ................................................................................................................................................. 29
10.1 EVENT > ALARM PORT....................................................................................................................... 29
10.2 EVENT > MOTION .............................................................................................................................. 30
10.3 EVENT > TAMPER DETECTION ............................................................................................................ 31
10.4 EVENT > MAPPING ............................................................................................................................ 31
11. NETWORK ........................................................................................................................................... 32
11.1 NETWORK > IP SETUP ....................................................................................................................... 32
11.2 NETWORK > SERVICE PORT ............................................................................................................... 34
11.3 NETWORK > RTP .............................................................................................................................. 34
11.4 NETWORK > E-MAIL ........................................................................................................................... 35
11.5 NETWORK > DDNS ........................................................................................................................... 36
11.6 NETWORK > UPNP ............................................................................................................................ 37
12. SYSTEM .............................................................................................................................................. 38
12.1 SYSTEM > USER ............................................................................................................................... 38
12.2 SYSTEM > DATE & TIME .................................................................................................................... 39
10-2014-A
4
PixelPro Series
ZN-BxMTP Series User’s Manual
12.3 SYSTEM > MAINTENANCE .................................................................................................................. 40
12.4 SYSTEM > INFORMATION.................................................................................................................... 42
13. DIMENSIONS ...................................................................................................................................... 43
14. SPECIFICATIONS ............................................................................................................................... 45
5
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
1. Product Features
The GANZ PixelPro is a high performance H.264 network camera, designed for
demanding security installations. It delivers crisp, clear images, disclosing every detail,
thanks to its top quality Megapixel progressive CMOS sensor and advanced image
processing.
Supported by the industry’s largest base of video management software, the GANZ
PIxelPro provides the perfect solution for securing bank offices, airports and other
facilities, and for traffic surveillance, over IP based networks.
The optimal Power over Ethernet (IEEE 802.3af) support power to the camera to be
delivered via the network, eliminating the need for a power outlet and reducing
installation costs. Steady power could be guaranteed with a central Uninterruptible
Power Supply (UPS).
The GANZ PixelPro offers a comprehensive set of network security and management
features.
This includes support for port based network control (IEEE802.1X), which allows the
camera to be connected to a network secured with this control, and HTTPS encryption,
which provides a secure channel between camera and application. It also enables
authentication of the video source. Video products are efficiently managed with the
powerful GANZ PixelPro Camera Management tool, which is provided on the
Installation CD which comes with each GANZ PixelPro camera.
6
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
1. Network connector
The GANZ PixelPro connects to the network via a standard network cable, and
automatically detects the speed of the local network segment (10BaseT/100BaseTX
Ethernet). This socket could also be used to power the GANZ PixelPro via Power over
Ethernet (PoE). The camera auto-senses the correct power level when using a PoE
switch, router or injector.
When you use a built-in Heater on the camera, particularly you don’t need connect the
PoE power to the camera. Camera need to connect 24VAC power.
2. Power Connector
24VAC power connector
Note: Heater function is required 24VAC power supply.
When 24VAC power connected to the camera, particularly you don’t need connect
PoE power.
Note: Heater will be turned-on/off automatically in low ambient temperatures.
3. I/O connector
Audio in
Audio in (line level), for line-in mono signal (only left channel is used from a stereo
signal)
Audio out
The Audio output (line level), which could be connected to a line output of a
microphone system or an active speaker with a built-in amplifier.
Alarm in
One analog (dry contact) alarm input
7
10-2014-A
ZN-BxMTP Series User’s Manual
PixelPro Series
Alarm out
One relay output (0.5A 125VAC / 1A 30VDC)
Pin Assignment
4. Micro SD card
Save snapshot images onto a Micro SD card.
5. Control Button
This button has 3 functions by pressing time.
1) Switch NTSC / PAL format (less than 1 second)
2) System reboot (around 5 seconds)
3) Factory Default Reset (More than 10 seconds)
6. Status LED
LED Color
Indication
On
Green
Flashes
Unlit
Red
-
System Status
Connection to 10/100Mbps Network / LAN.
Network connection is established.
Indication of network activity.
Camera is booting up.
No network connection established.
When no or incorrect power is supplied.
On
Camera reset is in progress.
Flashes
Factory Default settings are in progress.
7. Video Output for Service monitor
This analog video output is available. Use accessory cable to video output.
8
10-2014-A
ZN-BxMTP Series User’s Manual
PixelPro Series
Adjustment
A: Rotate locking screw
B: Tilt locking screw
C: Pan locking screw
9
10-2014-A
ZN-BxMTP Series User’s Manual
PixelPro Series
Mounting to a ceiling / wall
Secure the camera to ceiling or wall with supplied tapping screws like below.
For waterproofing purposes, apply the “Silicone sealant” around the area where
the mount base contacts the wall or ceiling.
ANCHOR (3)
TAPPING SCREW M4x30 (3)
Silicone sealant
ANCHOR (4)
TAPPING SCREW M4x30 (4)
WRENCH BOLT M4x12 (3)
MOUNT BRACKET
Silicone sealant
ANCHOR (4)
TAPPING SCREW M4x30 (4)
WRENCH BOLT M4x12 (3)
MOUNT BRACKET
Silicone sealant
10
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
2. Accessing the Camera
Follow the instructions in the GANZ PixelPro Installation Guide to install the camera.
The GANZ PixelPro could be accessed with most standard operating systems and
browsers. The recommended browser is Internet Explorer for Windows with other
operating systems.
2.1 Access from a browser
1. Start a browser (Internet Explorer)
2. Enter the IP address or host name of the camera in the Location/Address field of
your browser. Press Enter.
3. Login dialog will appear when the camera is accessed for the first time.
4. The default user name is ADMIN, and password is 1234.
5. The camera’s Live View page is now displayed in your browser.
Note: The layout of the live view page in the camera may have been customized to
meet specific requirements. Consequently, some of the examples and functions
featured here may differ from those displayed on your own Live View page.
11
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
2.2 Accessing the camera from the Internet
Once installed, the camera is accessible on the local network (LAN). Configure the
router/firewall to allow incoming data traffic to access the camera from the Internet. For
security reasons this is usually done on a specific port. Please refer to the
documentation for router/firewall for further instructions.
2.3 Adjusting the Image and Focus
To adjust the position of the lens:
1. Open the Live View page in your web browser.
- Select the Setup tab, and open the Analog output page.
- Select the ‘Video Format' or “ON”.
2. Connect analog monitor to the VIDEO OUT (BNC) on the supplied cable after
connected the supplied Video monitor cable with video output connector.
- Control the ZOOM/FOCUS by the Lens Adjustment window, and adjust the camera
angle.
For lens adjustment method, please refer to “5.2.5 Lens Adjustment”.
3. Check the image from the Live View page on your web browser.
4. You can refocus adjustment by Lens Adjustment window, if you want fine lens
adjustment.
2.4 The Live View page
Enable/Disable PC Speaker output
Enable/Disable PC Microphone input
Digital Zoom
Snap Shot
Full Screen
Video Stream change: First stream  Second stream
Play: Click this button by manually to start the stream
Stop: Click this button by manually to stop streaming
NOTE: It is possible that not all the buttons described below will be visible unless the
Live View page has been customized to display them.
12
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
2.5 Video stream types
H.264 protocols and communication methods
• RTP (Real-time Transport Protocol) is a protocol that allows programs to manage the
real-time transmission of multimedia data, via unicast or multicast.
• RTSP (Real Time Streaming Protocol) serves as a control protocol, to negotiate the
type of transport protocol to use for the stream. RTSP is used by a viewing client to
start a unicast session.
• UDP (User Datagram Protocol) is a communications protocol that offers limited
service for exchanging data in a network which uses the Internet Protocol (IP).
UDP is an alternative to the Transmission Control Protocol (TCP). The advantage of
UDP is that, it is not required to deliver all data and may drop network packets when
there is network congestion. This is suitable for live video, as there is no point in retransmitting old information that will not be displayed anyway.
• Unicasting is communication between a single sender and a single receiver over a
network. This means that the video stream goes independently to each user, and each
user gets own stream. A benefit of unicasting is, in case one stream fails, it only affects
one user.
• Multicasting (Will be supported) is bandwidth-conserving technology that reduces
bandwidth usage by simultaneously delivering a single stream of information to multiple
network recipients. This technology is used primarily on delimited networks (intranets),
as each user needs an uninterrupted data flow and should not rely on network routers.
2.6 How to stream H.264
Deciding on the combination of protocols and methods to use depends on your viewing
requirements, and on the properties of your network. Setting the preferred method(s) is
done in webpage.
RTP+RTSP
This method (actually RTP over UDP and RTSP over TCP) should be your first
consideration for live video, especially when it is important to always have an up-to-date
video stream, even if some images are lost due to network problems. This could be
configured as multicast or unicast.
RTP/RTSP/Multicasting (Will be supported) provides the most efficient usage of
bandwidth, especially when there are large numbers of clients viewing simultaneously.
Note however, that a multicast broadcast could not pass a network router unless the
router is configured to allow this. For example, It is impossible to multicast over the
Internet.
13
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
RTP/RTSP/Unicasting should be used for video-on-demand broadcasting, so that
there is no video traffic on the network until a client connects and requests the stream.
However, as more and more unicast clients get connected, the traffic on the network
will increase and may cause congestion. Although there is a maximum of 10 unicast
viewers, note that all multicast users combined count as 1 unicast viewer.
RTP/RTSP
This unicast method is RTP tunneled over RTSP. This could be used to exploit the fact
that it is relatively simple to configure firewalls to allow RTSP traffic.
3. The Setup
The GANZ PixelPro is configured from the Setup link, which is available on the top left
hand side in the web interface. This configuration could be done by:
• Administrators, who have unrestricted access to all settings under the Setup tab.
Accessing the Setup link from a browser
1. Start your web browser and enter the IP address or host name of the camera into the
address bar.
2. The Live View page is now displayed. Click on the Setup tap.
14
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
4. Analog output
Toggle menu changed to “ON/OFF” from FW1558 and later.
4.1 Analog Output Setup
Toggle the Analog video output to “ON/OFF” from BNC output of the camera.
Analog output allows selection of Video output format from BNC output of the camera.
NTSC, PAL: Analog Output is selectable.
This Analog Video Format menu moved to “Codec” page from FW1558 and later.
5. Video
The following descriptions show examples of some of the features available in the
GANZ PixelPro.
5.1 Codec
These are the tools for adjusting the H.264 settings and controlling the video bit rate.
15
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
H.264
This is a video compression standard that makes good use of bandwidth and which
could provide high-quality video streams at less than 1 Mbit/s.
The H.264 standard provides scope for a large range of different coding tools for use by
various applications in different situations, and the GANZ PixelPro provides certain
subsets of these tools.
Using H.264, it is also possible to control the bit rate, which in turn allows the amount of
bandwidth usage to be controlled. CBR (Constant Bit Rate) is used to achieve a specific
bit rate by varying the quality of the H.264 stream. While using VBR (Variable Bit Rate),
the quality of the video stream is kept as constant as possible, at the cost of a varying
bit rate.
Motion JPEG
This format uses standard JPEG still images in the video stream. These images then are
displayed and updated at a rate sufficient to create a stream that shows constantly
updated motion.
The Motion JPEG stream uses considerable amounts of bandwidth, but also provides
excellent image quality and access to every individual image contained in the stream.
Multiple clients accessing Motion JPEG streams could use different image settings.
Codec
H.264 / MJPEG
Size
Video output resolution. See the next page for the output resolution table.
Frame rate
1~30fps in normal mode (1~15fps for slow shutter mode)
Note: If the slow shutter mode is turned on and the low light condition is met, the
frame rate is automatically goes down. In this case, the frame is half of the
normal mode.
GOP Size
1 ~ 60 frames
Bit-rate control (CBR or VBR)
When using H.264 compression, if there is only limited bandwidth available, a constant
bit rate(CBR) is recommended, although this may compromise image quality. Use a
variable bit rate(VBR) for the best possibly image quality.
Average Bit-rate (512Kbps ~ 10Mbps)
Recommended bit rate for D1: 800Kbps ~ 1Mbps
Recommended bit rate for 1.3M(720p): 3Mbps ~ 4Mbps
Recommended bit rate for 2.0M(1080p): 6Mbps ~ 8Mbps
16
10-2014-A
ZN-BxMTP Series User’s Manual
PixelPro Series
Analog Video Format
Analog output allows selection of Video output format from BNC output of the camera.
NTSC, PAL: Analog Output is selectable.
Anti-Flicker mode (Flicker less mode) moved to “Camera” setup menu from FW1558 and later.
60Hz:NTSC
50Hz:PAL or flicker-free mode(to use the camera in locations lit by fluorescent lighting).
Video Mirroring
Video Mirroring mode can be set to None, Horizontal, Vertical or Flip (H+V).
Bandwidth Limit
Limit the bandwidth that the GANZ PixelPro can use during a network connection.
Max Bandwidth
Specify the maximum bandwidth that the GANZ PixelPro can use during a network
connection.
< Output resolution table for PixelPro>
First Stream
Second Stream
1920x1080
704x480
640x480
640x360
640x352
352x288
352x240
320x240
-
1280x1024
704x480
640x480
640x360
352x288
352x240
320x240
-
-
1024x768
704x480
640x480
640x360
352x288
352x240
320x240
-
-
1280x720
1280x720
704x576
704x480
640x480
640x360
352x288
352x240
320x240
704x576
704x576
640x480
640x360
352x288
-
-
-
-
704x480
704x480
640x480
640x360
352x240
-
-
-
-
640x480
640x480
320x240
-
-
-
-
-
-
640x360
640x360
320x240
-
-
-
-
-
-
352x288
352x288
-
-
-
-
-
-
-
352x240
352x240
-
-
-
-
-
-
-
320x240
320x240
-
-
-
-
-
-
-
17
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
5.2 Camera
This section allows you to adjust various camera settings.
5.2.1 Exposure Control
Exposure Mode
Auto: Use this settings for automatic exposure control.
Manual: Use these settings to control camera exposure manually.
Auto (Motion Priority): Use this settings to be improved blurred images of the moving
objects under low light conditions. Image noises would be increased under the low
light conditions. *This function is available from FW1558 and later.
To compensate for poor lighting conditions, you can adjust the Color level, Brightness,
Sharpness, Contrast and Exposure control.
NOTE: When AE is enabled, some of the submenus (AGC Gain, e-Shutter Speed) will
be disabled.
Max AGC Gain
For low light conditions, adjust to a higher value, such as 36dB.
Max AGC Gain can be set to LOW, MID, HIGH or MAX.
18
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
Max Shutter Speed
Slowest shutter speed can be selected from the menu.
*This function is available from FW1558 and later.
Anti-Flicker Mode (Flicker less mode)
Anti-Flicker Mode can be set to 60Hz, 50Hz or OFF.
60Hz: NTSC
50Hz: PAL or flicker-free mode (to use the camera in locations lit by fluorescent lighting).
OFF (This mode is available from FW1558 and later.)
P-Iris Control
P-Iris controls can be set to Auto, Best Quality, Depth of Field or Manual.
“Best Quality” and “Depth of Field” functions are available from FW1558 and later.
Auto: Lens Iris will be controlled such as standard Auto Iris lens.
Best Quality: Lens Iris positions will be controlled to best quality positions of
the lens under bright conditions.
Depth of Field: Lens Iris positions will be controlled to small aperture positions
to make depth of field under bright condition.
Manual: Lens Iris positions can be controlled to specified positions manually.
And the adjusted Iris positions does not move automatically.
Slow Shutter
For low light conditions, turn on slow shutter mode.
Slow shutter speed can be set to x2, x4, x8 or OFF.
BLC Control (Back Light Compensation)
The BLC adjusts the exposure of scenes with strong backlight in the center-bottom of
the image. When the image background is too bright, or the objects are too dark,
backlight compensations make the objects appear clearer. The settings for low light
behavior determine how the camera behaves at low light levels. These settings affect
video image quality and noises appears on the images.
The BLC can be set to Adaptive, Zone or OFF.
“Adaptive” and “Zone” functions are available from FW1558 and later.
Adaptive: The mode works detections and compensations automatically.
Zone: Can be set the detections areas for BLC behaviors from Lower, Middle, Upper, Left or
Right.
5.2.2 Day & Night Control
Day & Night Mode
Auto/Day/Night/Schedule- If set to Auto, the camera will automatically switch
according to the current lighting conditions.
Schedule- You can specify the schedule of Day mode.
* Schedule is available from FW1333 and later.
19
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
5.2.3 White Balance Control
WB (White Balance) Mode
WB mode can be set to Auto, Auto (wide mode), Custom (one-shot mode), WB Hold or
Manual. “Custom” / “WB Hold” functions are available from FW1558 and later.
Auto: ATW (Auto Tracking White balance)
The White balance adjustment setting is used to make the colors in the image appear
consistent, compensating for the different colors present in different light sources.
The GANZ PixelPro camera can be set to automatically identify the light source and
compensate for its color temperature.
Auto (wide mode): WB adjustment range is wider than Auto mode.
Custom (one-shot mode): WB will be fixed after adjusted WB in ATW, and then the
mode to be switched to the WB Hold mode automatically.
WB Hold: When the WB Hold was enabled, WB to be fixed.
Manual: When Manual White Balance is enabled, WB mode for the light sources can
be selected from the following fixed mode;
Indoor (2800K), Outdoor (6500K), or Fluorescent (4000K)
5.2.4 Image Property Control
Modify the video signal parameters, such as: Brightness, Sharpness, Contrast, and
Color.
Sharpness (Default: 8, Range: 1~15)
Brightness (Default: 15, Range: 0~30)
Contrast (Default: 15, Range: 0~30)
Color
(Default: 15, Range: 0~30)
5.2.5 Lens Adjustment
Adjust the lens (Zoom, Focus & Iris) from this window.
One Push Focus: Camera will automatically adjust the focus.
Default: Back to initial position (wide end).
Note) please click the default button to adjust the lens position to initial position, when
lens adjustment does not worked fine.
20
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
6. Audio
The GANZ PixelPro camera could transmit audio to other clients, using a connected external
microphone and could play audio received from other clients via connected speakers. This
section describes how to configure the basic audio settings for the GANZ PixelPro camera,
such as setting the communication mode, adjusting the sound levels in the microphone and
speakers connected to the camera.
Note: The speakers connected to the audio output must have a built-in amplifier, such
as PC speakers.
Audio
ON/OFF : Check this to enable audio in the GANZ PixelPro camera.
Codec
G.711 u-law
MIC Volume
Speaker Volume
Adjust the MIC and Speaker Volume.
Audio Input
Audio from a connected a line source could be connected to the Audio in connector of
the GANZ PixelPro camera. If there are problems with the sound input being too low or
high, adjust the input gain for the microphone connected to the GANZ PixelPro
camera.
21
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
7. Live
7.1
Setup
The GANZ PixelPro could support 10 simultaneous users. In case of multicast, the
GANZ PixelPro could support unlimited number of users. If supported on the network,
consider using multicasting, as the bandwidth consumption will be much lower.
Viewer Setup
LiveView Protocol
RTP Unicast (UDP) / RTP Multicast (UDP) / RTP over RTSP (TCP)
Buffering Time (frame based)
Determines (0 ~ 90) x 1/30 sec (0 ~ 3sec)
Viewer OSD Setup
Date : Determines whether the date is displayed.
Resolution : Determines whether the camera title is displayed.
Event State : Determines whether the event state is shown on display window.
22
10-2014-A
PixelPro Series
7.2
ZN-BxMTP Series User’s Manual
Privacy Masking
This uses masking to hide sections that you do not want to appear in the shooting
screen. Maximum 2 locations can be hidden with color.
Mask Area
All View：Shows the masking area both Area 1 and 2.
Click the Masking Area 1 or 2 to make a masking.
Mask color
Sets the mask color
Black, White, Light Gray, Dark Gray, Yellow, Red, Blue, Green
Mask Creation Procedure
1. Click Privacy Mask in the Live menu.
2. Select Area1 or 2 to activate a setup window.
3. Set the Mask Color in the drop-down list.
4. Click the Masking window, and select an area that you want to specify the masking
area.
5. Click Save.
Note: When the Privacy Masking is set, analogue output will be changed to OFF state
automatically.
* Privacy masking is available from FW1227 and later.
23
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
8. SD Card
8.1 Configuration
SD Card Configuration
This configuration page allows you to save still images to the Micro SD (SDHC) card.
Overwriting
The system will overwrite the oldest data on the SD card to continually record
the newest data.
SD Status
Shows present SD card status. It also shows whether the SD card is present and the
capacity left on it in kilobytes (KB).
Mount / Unmount The Mount button notifies the system after the SD card is inserted.
The Unmount button is to notify the system before the SD card is removed. This is a
similar function to the ‘remove the hardware safely before taking out the USB’ in the
Windows OS.
NOTE: The user can download the images from the SD card using the FTP function.
Turn FTP server on and connect to the camera. See Chapter 9.1 for details.
24
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
8.2 Event
Event SD Writing
You can configure the camera to store still images based on events such as Alarm In
and Motion detection.
SD Writing
SD Writing will Enable / Disable event recording to the SD card.
When Disabled, all remaining menus will be deactivated.
Directory
The name of the sub-directory where the still images will be stored when an Event
occurs.
File Prefix
You may add a file name prefix to the stored image file name.
Example: If the file prefix is ‘alm’, the still image would be saved as
alm_date_time.jpg.
SD Write Mapping
Choose which types of events will be recorded to the SD card by checking the desired
event.
Effective Period lets you decide whether to save all the events that are happening at
all hours of the day, or only the events that occur within during specific times of the
day. The Schedule method is used to save events on the SD card during a specific
time range. The start time and the end time can be set using the dropdown list.
25
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
8.3 Periodical
Periodical SD Writing
It is setting page to save the still images in the Micro SD card periodically.
The Directory and File Prefix fields are same as on the SD Card > Event page.
Interval allows for saving still images based on frequency (1 image every 10 sec, for
example).
Use the drop-down control to set from 10 seconds to 1 hour.
Effective Period is also configured the same as on the SD card > Event page.
Periodically, it saves the still image during a specific time range only.
26
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
9. FTP
9.1 FTP > Config
Server Configuration (This function is N/A on this model)
External Server Configuration
It is setting page to transmit the still shot to remote sites, using the FTP server.
Specify the external FTP server information such as IP address, port number,
Username and password.
Note :
When the first stream is set to 1920x1080, please set the 2nd stream to MJPEG or
H.264 with resolution less than 352x288. If 2nd stream is set to H.264 greater than
640x352, 30fps streaming is not guaranteed due to performance limitation.
9.2 FTP > Event
27
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
Event FTP Sending
It enables FTP transmission triggered by event.
Directory : This folder will be created into external FTP server automatically.
File Prefix : The file name will start from this prefix.
Mapping : You can specify event mapping for Event FTP.
Effective Period : You can specify “Always” or “Schedule”
9.3 FTP > Periodical
Periodical FTP Sending
It enables FTP transmission periodically.
Directory : This folder will be created into external FTP server automatically.
File Prefix : The file name will start from this prefix.
Interval : You can specify interval time for uploading to FTP.
Effective Period : You can specify “Always” or “Schedule”
28
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
10. Event
10.1 Event > Alarm Port
Alarm Input - Used for connecting external alarm devices and triggering images for
specific alarm-based events. The input is typically connected to a motion
detector or any other external security device, and images could be
uploaded whenever the detector is activated. Maximum 5VDC is allowed
on the input.
Output - This could drive a maximum load of 0.5A 125VAC / 1A 30VDC directly or
heavier loads by connecting additional relay circuitry. If the output is used
with an external relay, a diode must be connected in parallel with the load for
protection against any voltage transients.
Duration - This parameter sets the minimum tampering period, that is, an alarm will not
be triggered until this period has lapsed, even if the tampering conditions are
otherwise met. This could help to prevent false alarms for known conditions
that affect the image.
Caution! Connecting AC to the inputs/outputs will damage the unit.
Please note the connection, voltage and current.
29
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
10.2 Event > Motion
Motion Detection
Motion detection is used to generate an alarm event with analyzes the video whenever
objects movements occurs in the video image. Maximum 4 windows can be configured.
Area Sensitivity：1(low) ~ 10(High) – The higher the number is, the higher the
sensitivity level becomes.
Configuring Motion Detection
1. Click Motion Detection in the Event Config menu.
2. Select an Area from Area1 to 4 to activate a Motion setup window.
3. Click the Motion window, and select an area that you want to specify the Motion
area.
4. Select sensitivity value (1 ~ 10) in the drop-down list.
Any detected motion within an active window is then indicated by red shade onto the
Activity window.
5. Click Save.
Note: Using the motion detection feature might decrease the camera’s overall
performances, depending on camera settings.
30
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
10.3 Event > Tamper Detection
Tamper Detection
Camera detects the tampering with analyzes the video image. When the camera angle
is moved, covered or sprayed to the front cover, defocusing severely, it can be triggered
to an alarm event.
Tamper detection can be set to LOW, MID, HIGH or OFF.
Notes: Too simple or dark background cause detection fail ratio.
Indoor light (or similar situation) turn ON or OFF would cause False Detections.
If the video scene is similar or same between ‘before’ and ‘after’ angle
change, it cause detection fail.
This function is added from FW1558 and later.
10.4 Event > Mapping
It is possible to define conditions that would cause the camera to respond with certain
actions. A triggered event happens as a result of a trigger, which could be motion
detection, an external alarm input or tamper detection.
For example,
Alarm out events could be triggered by video motion detection, alarm in or tamper
detection.
E-mail could be sent by either video motion detection, alarm in or tamper detection.
10-2014-A
31
PixelPro Series
ZN-BxMTP Series User’s Manual
11. Network
11.1 Network > IP Setup
Network Settings
Click the Setup > Network > IP Setup to see the current network settings.
IP Address Configuration The GANZ PixelPro supports both IP version 4 and IP version 6 (IPv6 will be
supported in V3.00). Both versions may be enabled simultaneously, and at least
one version should be always enabled.
When using IPv4, the IP address could be set automatically via DHCP, or a static IP
address could be set manually. If IPv6 is enabled, your camera receives an IP address
according to the configuration in the network router.
There are also options for setting up notification of changes in the IP address, and for
using the Internet Dynamic DNS Service.
Notes: • To receive notification whenever the camera’s IP address changes (via
e.g. DHCP), configure the options for notification of IP address change.
See Services below. • If your DHCP server could update a DNS server,
you could access the GANZ PixelPro by a host name which is always the
same, regardless of the IP address.
DNS Configuration
DNS (Domain Name Service) provides the translation of host names to IP addresses
on your network.
•1st DNS server
Enter the IP address of the primary DNS server for your network.
•2nd DNS server
Enter the IP of the Secondary DNS, which is used if the Primary DNS server is
unavailable.
32
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
How to assign IP address
Default setting is set to “DHCP” and “UPnP” function is set to ON.
If your network has DHCP server and UPnP function is enabled on your PC, you
can find the network camera in “My network”.
If DHCP server is not available in your network, please assign IP address as
following process.
②
③
④
1)
2)
3)
4)
Execute “MultiUpgradeTool.exe”, it will search the camera on the network.
After the camera is listed in camera list, select the camera.
Type in the all network information.
Click “Change IP address” button to set network settings to the camera.
When you double-click the camera within the list, the default web browser (Internet
Explorer or compatible equivalent) will open and automatically connect to the camera.
33
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
11.2 Network > Service Port
Service Port
HTTP port- The default HTTP port number (80) could be changed to any port within the range
1-65535. This is useful for simple port mapping.
RTSP port- The RTSP protocol allows a connecting client to start an H.264 stream. Enter the
RTSP port number to use. The default setting is 554.
NOTE: After changing the default port numbers, the user can use the
“MultiUpgradeTool.exe” to search and connect automatically.
11.3 Network > RTP
34
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
RTP port range, Multicast Setup
These settings are the IP address, port number, and Time-To-Live value to use for the
video stream(s) in multicast H.264 format.
Only certain IP addresses and port numbers should be used for multicast streams.
11.4 Network > E-mail
You must turn Notification to ‘On’ and then enter the host names or addresses for your
mail servers in the fields provided, to enable the sending of event and error email
messages from the camera to predefined addresses via SMTP.
Note1)
Frequency : Mail server may register the sender to SPAM list when frequency is
set to “1 Min”. It may be better to set “5 Min” for safe side.
Note2)
From : Specify the name who sent e-mail notification. It may be better to use e-mail
format like as [email protected]. Some e-mail server will refuses it.
35
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
11.5 Network > DDNS
How to setup the DDNS:
1) DDNS set to ON.
“mac address.dvrlink.net” is registered to the DDNS server.
User can connect to the camera with: “http://mac address.dvrlink.net”.
2) DDNS set to ON and user inputs “user-defined name”.
“mac address.dvrlink.net” and “user-defined name.dvrlink.net” are both
registered together.
User can connect to the camera using either:
“http://mac address.dvrlink.net” or “http://user-defined name.dvrlink.net”.
If “user-defined name” is already registered, an error message is shown, try a different
name.
36
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
11.6 Network > UPnP
Universal Plug & Play (UPnP) allows you to find the IP camera automatically on your
network.
In order to be able to detect the camera automatically, you must enable the UPnP function on
both the camera and on your PC.
Camera : Set UPnP to “ON”
PC : Open “Control Panel” >”Network Connection”
Select “Advanced” >”Optional Networking Components…”
37
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
Select “Network Services” and click “Details”. Then select “UPnP user Interface”
12. System
12.1 System > User
Access the camera and the Configure Root Password dialog appears.
Enter the User name: ADMIN and password is 1234.
To changed password or add a user click SETUP > SYSTEM > USER. Fill the User ID,
Password and E-mail server. Select Group. Then press ADD button and click SAVE.
Note: The default administrator user name ADMIN is permanent and could not be deleted or
altered.
38
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
12.2 System > Date & Time
Date & Time Format - specify the formats for the date and time (12h or 24h) displayed in the
Live View video streams. Use the predefined formats or use your own custom date and time
formats.
Network Time Server - the camera will obtain the time from an NTP server every 60 minutes.
Specify the NTP server's IP address or host name.
Time zone setup – Select your time zone from the drop-down list.
D.S.T (Daylight Saving Time) - ON/OFF
39
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
12.3 System > Maintenance
System Name
Choose a system name to identify the camera when using e-mail notifications.
System Reboot
Reboot the camera.
Factory Default
To reset the camera settings to the original factory default settings.
Enable Firmware Upgrade / Firmware Updates
To upgrade Firmware of the camera, follow the instruction below.
NOTE: Preconfigured and customized settings should be saved before the firmware is
upgraded.
1) Enable Firmware Upgrade mode with clicking “OK” of Enable Firmware
Upgrade menu.
2) The camera automatically switches to Firmware Upgrade mode.
40
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
3) When Firmware upgrade menu is displayed, browse to the desired firmware file
on your computer. Click OK.
NOTE: Do not disconnect power to the unit during the upgrade. The unit will restart
automatically after the upgrade has completed. (1~5 minutes)
System Reset (Factory Default Reset)
There are two ways to reset the camera back to factory default. holding down about 1020 sec the reset button on the Network cable
Using the web browser:
1. Go to SETUP > System > Maintenance.
2. Click Factory Default Button and wait 1 minute for camera to reboot.
Using the Reset Button:
1. Holding down 15-20 sec the reset button on the Network cable.
2. Release your finger on the reset button, waiting about 1 minute for camera reboot
NOTE: The unit will now have the default IP address from a DHCP server.
Use the ‘“MultiUpgradeTool.exe” to discover and connect to the camera.
41
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
12.4 System > Information
System Information
You can confirm the system information about the camera here.
42
10-2014-A
ZN-BxMTP Series User’s Manual
PixelPro Series
13. Dimensions
13-1. Without Mount Bracket
(291; B2MTP-2)
-Top view-
10-2014-A
-Bottom view-
UNIT: mm
43
ZN-BxMTP Series User’s Manual
PixelPro Series
13-2. With Mount Bracket
(335; B2MTP-2)
3/4” NTP
3/4” NTP
-Top view-
10-2014-A
-Bottom view-
UNIT: mm
44
ZN-BxMTP Series User’s Manual
PixelPro Series
14. Specifications
H.264 / MJPEG Network Camera
Dual Stream
Motion Triggered Alarm/ External Alarm In
Multi Language GUI support
ONVIF Compliant
Dual Power: 24VAC, PoE(802.3af)
SONY CMOS Sensor IMX122
On The Fly supported @ GOP/Bitrate/FPS stetting
2D DNR. (Depends on CODEC configuration)
- 3D TBD
DPC(Defective Pixel Correction) on the fly
42 IR LEDs
Motorized Zoom, Focus and P-iris
True Day & Night
Analog Hybrid Output(Installation Only)
Micro SD card slot
Heater
Fan
Privacy Masking
Product Features
Image Sensor
Max. Resolution
1920 x 1080; (2MTP), 1280 x 1024; (1MTP)
Effective Pixels
1984(H) x 1225(V)
Effective Image Size
White Balance
Electronic Zoom
AGC
BLC
Iris
Shutter Speed
CAMERA
Slow Shutter
Lens
Angle of View
Day & Night
S/N ratio
Min. illumination
ANALOG
(Installation Only)
AUDIO
1/2.8" Sony IMX122 CMOS Sensor
Video Signal
Monitor Output
Scanning Frequency
In/Out
CODEC
5.56mm(H) x 3.43mm(V), 6.53mm(Diagonal)
ATW / MANUAL(PRESET)
2 ~ 10x(Client Software)
Yes
Yes
Motorized Iris / MANUAL / AES
1/4, 1/10, 1/12.5, 1/15, 1/20, 1/25, 1/30, 1/50, 1/60, 1/100,
1/120, 1/240, 1/480, 1/960, 1/1024, 1/2000s
2x, 4x, 8x
Motorized Zoom and Focus lens
ZN-B2MTP ;
f=3~9mm, F1.2~2.1
ZN-B2MTP-2 ; f=10-23mm, F1.6~2.6
ZN-B2MTP;
Horizontal ; f=3mm(Wide) 104.2°, f=9mm(Tele) 35.5°
ZN-B2MTP-2;
Horizontal ; f=10mm(wide) 30.5° ,f=23mm(Tele) 13.2°
Removable IR Cut Filter
48.8 dB or more
Color
IR LED ON
ZN-B2MTP ;
0.16 lux
0 lux
ZN-B2MTP-2 ;
0.29 lux
0 lux
NTSC / PAL selectable
Composite Output(BNC), 75 ohm 1Vpp
NTSC: (H) 15.734 kHz, (V) 59.94 Hz
PAL: (H) 15.625 kHz, (V) 50 Hz
Line in, Line out
External Amplifier is needed
G.711 / 8K sampling
45
10-2014-A
ZN-BxMTP Series User’s Manual
PixelPro Series
Network
Image Compression
10BASE-T, 100BASE-TX, RJ45
H.264
MJPEG : Image quality: 100 Steps(Q value)
1920 x 1080(Full HD; B2MTP), 1280 x 1024(SXGA),
Resolution
1024x768(XGA), 1280 x 720(720p)
640 x 480(VGA), 640 x 360(HVGAW), 320 x 240(QVGA)
704x480/576(4CIF), 352x240/288(CIF)
IPv4, HTTP, SMTP, UPnP, DNS,
Protocol
RTSP, DDNS, RTP, TCP, UDP, RTCP,
DHCP, ARP, IGMP, ICMP, NTP, FTP
Frame Rate
1 fps ~ 25 fps / 1 fps ~ 30 fps
Internet Explorer 7.0 or above
NETWORK
Web Browser
Firefox
Chrome
PDA / Smart phone
Security
Password Protection
SDK(API)
HTTP based API
ONVIF Profile S
VMD
Alarm Trigger
POWER
User set 4 ROI(Region Of Interest)
10 Step Sensitivity
VMD, External Alarm Input
Alarm Event
E-mail notification(Snapshot), FTP transfer(Snapshot),
microSD Card(Snapshot), Alarm out
MJPEG image streaming with alarm status(TBD)
Power Consumption
1.0A @ AC24V, 10.3W (Heater OFF)
1.63A @ AC24V, 18.4W (Heater ON)
220mA @ DC48V(PoE), 10.6W (Heater OFF) Class0
Heater
microSD Card
External I/O Terminals
5W (AC24V is required)
SDHC card compatible
SanDisk, Transcend, Kingstone, Toshiba:
2G, 4G, 8G, 16G and 32GB
Alarm In x1: NO/NC Dry contact
Alarm Out x1: Relay output
Audio In x1, Audio Out x1
IR Number
FAN Number
OTHER
SPECIFICATIONS
Ambient Temperature
(Not Include Cold Start)
Ambient Humidity
Materials
Weight
Dimensions(W x H x D)
42 IR LEDs
1
-10ºC ~ 50ºC(14ºF~122ºF)
With Heater -40ºC ~ 50ºC(-40ºF~122ºF)
less than 90%, Non-condensing
Aluminum Diecasting
2.0 kg
ZN-B2MTP ; Φ145 X 330(H) mm
ZN-B2MTP-2 ; Φ145 X 335(H) mm
IP66
IP Rating
* The specifications and/or appearance of the product may change without a prior notice.
46
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
47
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
48
10-2014-A
PixelPro Series
ZN-BxMTP Series User’s Manual
49
10-2014-A
ZN-BxMTP Series User’s Manual
PixelPro Series
Revision History
REV#
06-2014-A
10-2014-A
DATE(M/D/Y)
06/17/2014
10/30/2014
Comments
Added revision# to each pages.
Minor update on Specification
Added schedule on Day & Night menu
Additions and revisions for new FW(1558).
Minor update on some pages.
50
10-2014-A