Download Owner`s Manual

CO
PY
Owner’s Manual and Assembly Instructions
Model # 368200 & 368000
**U.S. and Canada customers ONLY**
IF ASSISTANCE IS NEEDED,
DO NOT CONTACT THE STORE!
CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865
HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)
Call or visit our Web site at www.lifetime.com for Saturday hours
**For customers outside the U.S. or Canada, please contact the store for assistance.**
Lifetime Products, Inc.
0/"OXs&REEPORT#ENTER"LDG$
#LEARFIELD5TAH
This product is intended for use by children ages 3 to 12
and is for residential use only.
6/28/2010
Instruction # 1070883 B
1
Before Beginning Assembly!
Do not start assembly until you have read all instructions.
Tools Required for Assembly
1/2” wrench
3/4” wrench
Phillips Screwdriver
Power Drill
Drill Bit 3/8”
Drill Bit 1/4”
12’ Step Ladder (not extension ladder)
Hammer
3/16” and 1/4” Allen wrench (included)
CO
PY
The Person Symbol indicates the number of adults
required to complete the assembly step.
Two Adults Required for Assembly
Three Adults Required for Assembly
Four Adults Required for Assembly
Only adults should set up the play equipment. Do not allow children in
the setup area until assembly is complete.
Save this owner’s manual for future reference and in the event that the manufacturer
has to be contacted.
WARNING
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS
INJURY OR PROPERTY DAMAGE AND WILL VOID THE WARRANTY.
To ensure safety, do not attempt to assemble this playset without following the instructions carefully. Before
beginning assembly, read the instructions. Proper and complete assembly, use and supervision are essential for
proper orientation and to reduce the risk of accident or injury.
Most injuries are caused by misuse and/or not following instructions. Use caution when using this playset.
2
**IMPORTANT SAFETY INFORMATION**
PLEASE READ BEFORE BEGINNING ASSEMBLY:
Installation and Ground Preparation Instructions:
• Place the equipment on level, well-drained ground, not less than 6 ft. (1.8 m) from any structure
or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical
wires.
• Do not install home playground equipment over concrete, asphalt, packed earth, or any other hard
surface. A fall onto a hard surface can result in serious injury to the equipment user (see page 5).
Install the playground equipment with the slide facing North, this helps prevent the surface on the
slide from getting too hot.
•
• To prevent serious injury, warn children that they must not use the equipment until properly installed.
• With unstable soil conditions, we recommend anchoring the playset into the ground. Call our Customer Service Department at 1-800-225-3865 for more information.
Operating Instructions:
Observing the following instructions and warnings reduces the likelihood of serious or fatal injury.
• The maximum number of occupants that may safely use the entire playset including all components is eight with a maximum weight of 900 pounds.
• On-site adult supervision should be provided for children of all ages.
• Instruct children not to walk close to, in front of, behind, or between moving items.
• Instruct children not to twist swing chains or ropes or loop them over the top support bar since
this may reduce the strength of the chain or rope.
• Instruct children to avoid swinging empty seats.
• Teach children to sit in the center of the swings with their full weight on the seats.
• Instruct children not to use the equipment in a manner other than intended.
• Instruct children not to get off equipment while it is in motion.
• To prevent entanglement and strangulation, dress children appropriately using well-fitting shoes
and avoiding ponchos, scarves, jackets with neck drawstrings, helmets with straps, and other loosefitting clothing that is potentially hazardous while using equipment.
• Instruct children not to climb when the equipment is wet.
• Instruct children not to attach items to the playground equipment that are not specifically designed
for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables
and chain as they may cause a strangulation hazard.
3
Maintenance Instructions:
•
Check surfacing material and replenish as necessary to maintain proper depth (see page 5).
• Check all nuts and bolts twice monthly during the usage season for tightness and tighten as required. It is particularly important that this procedure be followed at the beginning of each season.
•
Remove any tripping hazards, such as exposed concrete footings, tree stumps, or rocks.
• Check all coverings for bolts and sharp edges twice monthly during usage season to be certain they are
in place. Replace when necessary. It is especially important to do this at the beginning of each new season.
• Check swing seats, ropes, cables and chains monthly during usage season for evidence of deterioration. Contact Customer Service for replacement parts.
• Sand rusted areas on tubular members and repaint using a non lead-based paint.
• Take plastic swing seats indoors or do not use when the temperature drops below 40 degrees F.
• If the warning sticker is illegible, destroyed or removed, contact Customer Service for a replacement.
Disposal Instructions: Disassemble and dispose of the playground equipment in such a way that no
unreasonable hazards will exist at the time the swing set is discarded. Follow all local disposal requirements.
Place the equipment no less than 6 ft. (1.8 m) from any structure or obstruction such as a fence, garage, house,
overhanging branches, laundry lines, or electrical wires. Make sure the clearance in front of and behind the
swings is at least twice the height of the swing bar. The impact surfacing needs to cover the entire recommended play area. Refer to the example below.
6 feet
14 feet
6 feet
6 feet
29 feet 8 inches
14 feet
6 feet
27 feet
4
Playset dimensions:
Recommended play area:
13’ 11” x 15’
29’ 8” x 27’
CONSUMER INFORMATION SHEET FOR PLAYGROUND SURFACING MATERIALS*
The U.S. Consumer Product Safety Commission (CPSC) estimates that about 100,000 playground
equipment related injuries resulting from falls to the
ground surface are treated annually in U.S. hospital
emergency rooms. Injuries involving this hazard pattern
tend to be among the most serious of all playground
injuries, and have the potential to be fatal, particularly
when the injury is to the head. The surface under and
around playground equipment can be a major factor in
determining the injury causing potential of a fall. It is
self evident that a fall onto a shock-absorbing surface
is less likely to cause a serious injury than a fall onto
a hard surface. Playground equipment should never
be placed on hard surfaces such as concrete or asphalt
and while grass may appear to be acceptable, it may
quickly turn to hard packed earth in areas of high traffic. Shredded bark mulch, wood chips, fine sand or fine
gravel are considered to be acceptable shock-absorbing
surfaces when installed and maintained at a sufficient
depth under and around playground equipment.
Table 1 lists the maximum height from which
a child would not be expected to sustain a life-threatening head injury in a fall onto different loose-fill surfacing materials if they are installed and maintained at
depths of 6, 9, and 12 inches. However, it should be
recognized that all injuries due to falls cannot be prevented no matter what surfacing material is used.
It is recommended that a shock-absorbing
material should extend a minimum of 6 ft. in all directions from the perimeter of stationary equipment such
as climbers and slides. However, because children may
deliberately jump from a moving swing, the shock absorbing material should extend in the front and rear of a
swing a minimum distance of 2 times the height of the
pivot point measured from a point directly beneath the
pivot on the supporting structure.
This information is intended to assist in
comparing the relative shock-absorbing properties of
various materials. No particular material is recommended over another. However, each material is only
effective when properly maintained. Materials should
be checked periodically and replenished to maintain
correct depth as determined necessary for your equipment. The choice of a material depends on the type and
height of the playground equipment, the availability of
the material in your area, and its cost.
Fall Heights for this Unit and Other Accessories.
(Compare heights in this table to the heights in the following table. We recommend using 12” of
Double Shredded Bark Mulch.)
Clubhouse
3, 5, or 7 feet
Monkey Bars
7 feet 6 inches
Swing Bar
7 feet 6 inches
Climbing Wall
8 feet
TABLE 1 — FALL HEIGHT IN FEET FROM WHICH A LIFE THREATENING HEAD INJURY
WOULD NOT BE EXPECTED
Type of Material
Material
Depth: 6 in. depth
Material
Depth: 9 in. depth
Material
Depth: 12 in. depth
Double Shredded Bark Mulch
6 ft
(fall height)
10 ft
(fall height)
11 ft
(fall height)
Wood Chips
6 ft
(fall height)
7 ft
(fall height)
12 ft
(fall height)
Fine Sand
5 ft
(fall height)
5 ft
(fall height)
9 ft
(fall height)
Fine Gravel
6 ft
(fall height)
7 ft
(fall height)
10 ft
(fall height)
Shredded Tires***
10 ft
(fall height)
N/A
(fall height)
N/A
(fall height)
*This information has been extracted from the CPSC publications “Playground Surfacing--Technical Information Guide” and “Handbook for Public Playground Safety.” Copies of these reports can be obtained by sending a postcard to the: Office of Public Affairs, U.S. Consumer Product Safety Commission,
Washington, D.C., 20207 or call the toll-free hotline: 1-800-638-2772.
***This data is from tests conducted by independent testing laboratories on a 6-inch depth of uncompressed shredded tire samples produced by four
manufacturers. It is recommended that persons seeking to install shredded tires as a protective surface request test data from the supplier showing the critical
height of the material when it was tested in accordance with ASTM F1292.
5
USE AT YOUR OWN RISK!
USING A DRILL IS NOT RECOMMENDED
FOR DRIVING BOLTS.
A cordless drill can be used for driving screws;
however, care should be taken not to
over tighten or strip screws.
If you decide to use a drill for driving bolts, follow the tips to reduce the chance of damaging the product:
1. Always start bolts by hand to prevent cross-threading.
2. Use a drill with the clutch set at the lowest setting that will drive the bolts.
3. Use an Allen wrench for final tightening of bolt to prevent over-tightening.
6
Parts List (Box 1) Kit Box 321002
ID
Item Description
Qty
Part #
1F
Cargo Net
1
8000727
1A
Rail, One Handle
4
8001261
1G
Binocular
1
8000874
1B
Rail, Two Handle
2
8001206
1H
Binocular Bracket
1
8000349
1C
Ladder Rung
2
8001263
1I
Steering Wheel
1
8000856
1D
Belt Swing
2
8001497
1J
Wheel Clicker
1
8000158
1E
Trapeze Swing
1
8000020
1K
Wheel Cap
1
8000850
1A
1C
1B
1I
1G
1F
1D
1H
1K
1J
1E
Parts List (Box 2) Kit Box 322003
ID
Item Description
Part #
2J
Round Roof Tube
2
8002853
2A
Deck
1
8001721
2K
Roof Railing
2
8001291
2B
Chalkboard
1
8001271
2L
Cargo Net Bottom Pole
1
8002439
2C
Deck Support
1
8001197
2D
45” D-Tube
1
8002846
Under-Deck Swing
2E
41” D-Tube
1
8001258
2M
Plastic Seat
3
8001093
Square Tubing
3
8001216
Qty
2F
Ladder Side D-Tube
1
8002843
2N
2G
44” Turn Bar
1
8002541
2O
3-Hole Bracket
1
8001219
2H
Cross Brace
4
8000252
2P
6-Hole Bracket
1
8001218
2I
Roof Truss
8
8002542
2Q
Soft Grip Chain
3
8000726
2N
2M
2B
2A
2O
2P
2Q
2D
2E
2C
2F
2G
2H
2I
2J
2L
2K
7
Parts List (Box 3) Box 320002
ID
Item Description
3A
A-Frame Pole
Qty
Part #
3F
Cargo Side D-Tube
1
8002838
2
8002526
3G
Right Vertical Pole
1
8001260
3B
Ladder Side Pole
1
8002849
3H
Left Vertical Pole
1
8002621
3C
Cargo Side Pole
1
8002556
3I
A-Frame Roof Tube
1
8002854
3D
Angled Ladder Leg
1
8002852
3J
Climbing Wall Roof Tube
1
8002855
3E
Angled Cargo Net Leg
1
8002537
3K
Climbing Wall Pole
1
8000326
3A
3B
3C
3D
3F
3E
3G (Right Vertical Pole)
3H (Left Vertical Pole)
Sticker is located here.
3I
3J
3K
Parts List (Box 4) Kit Box 322501
ID
Item Description
4A
Roof Panel
Qty
Part #
8002550
4
4A
Parts List (Bags 1, 2, & 3)
ID
Item Description
Qty
Part #
(Bag 1) 223001 Swing Bar
B1
Swing Bar
(Bag 2) 224000 Slide
B2
1
8002580
B3
B1
B3
B2
8
Slide
1
8000861
2
1051768
(Bag 3) 1052119 Climbing Wall
Climbing Wall Panel
Hardware List (All Hardware is located in Box 1 Part #1066388)
ID
Item Description
Qty
Part #
HL
HA
Bolt, 5/16” x 3/4”
HB
Bolt, 5/16” x 1 1/4”
Nut, Acorn 5/16”
19
8000165
52
8000162
9
8000163
HM
Nut, Nylock 5/16”
4
8000209
HN
Nut, Top Lock 5/16”
1
8000694
HC Bolt, 5/16” x 1 3/4”
2
8000134
HD Bolt, 5/16” x 2”
3
8000307
HO
Screw, #14 x 3/4”
32
8000522
HP
Screw, #14 x 1 1/4”
51
8000350
HE
Bolt, 5/16” x 2 1/2”
9
8000534
HQ
Quick Link
6
8001337
HF
Bolt, 5/16” x 3 1/2”
8
8001336
HR
Washer, Fender
1
8002914
HG Bolt, 5/16” x 4”
2
8001834
HS
Bolt, 5/16” x 1”
4
8000412
HH Bolt, Hex 5/16” x 2”
1
8000693
HT
Allen Wrench, 3/16” Equal Length
1
8002010
HI
Bolt, Eye 5/16” x 1 1/8”
3
8001300
HU
Allen Wrench, 3/16” Standard
1
8000355
HJ
Washer 1/4” Zinc
90
8002027
HV
Bit, # 3 Apex (not shown)
1
8000510
HK
Chalkboard Spacer, 1/2”
2
1066365
HW
Tap, 5/16 (not shown)
1
8000565
There may be extra hardware in this bag.
HT
HE
HA
HR
HF
HB
HG
HC
HH
HD
HI
HJ
HK
HL
HM
HN
HQ
HP
HO
HS
HU
Swing Hardware List (All Hardware is located in Box 1 Part #8000817)
ID
Item Description
SA
Pendulum
SB
SC
Qty
Part #
SD
Washer, Small Nylon 7/16”
12
8000154
6
8000014
SE
Washer, Large Nylon 7/16”
12
8000169
Bolt, 7/16” x 2”
6
8000167
SF
Allen Wrench, 1/4”
1
8000356
Nut, Acorn 7/16”
6
8000170
SB
SD
SE
SA
SC
SF
9
Caps, Hardware List (All Hardware is located in Box 1 Part #8002878)
ID
Item Description
Part #
CF
CA
Cap, Hole
20
8000265
CB
Cap, 3” Flat Round
4
8000996
CC Cap, 1 1/2” Dome
8
CD Cap, Angled Foot
6
CE
6
Cap, 1 1/2” Square w/Hole
Qty
Cap, Cargo Net Pole
2
8000883
CG Cap, Angled Ladder
2
8000788
CH Cap, D-Tube End
6
8001007
8001087
CI
Cap, Square Black 1 1/2”
14
1061365
8001306
CJ
Cap, Flat Black 7/8” x 1 1/2”
2
8000318
8001077
CK
Cap, Under-Deck Swing
1
1067453
There may be extra caps in this bag.
CE
CA
CB
CC
CD
CF
CG
CK
CH
CJ
CI
10
1
Parts for this Step are Located in Bag 1 and Box 3
HJ x 8
Insert the A-Frame Poles
(3A) into the Swing Bar
(B1) and secure as shown.
Make sure there is NOT a
nut insert in the location
specified.
HL x 4
HF x 4
3A
Holes should
face out as
shown
HL
HJ
HL
HJ
HJ
HF
HJ
HF
B1
HL
HL
Caution:
3A
Make sure there
is NOT a nut
insert here
2
HJ
HJ
HJ
HF
HJ
HF
Parts for this Step are Located in Box 2
HJ x 2
Attach the 44” Turn Bar (2G)
to the A-Frame Poles (3A).
Secure both sides as shown.
HA x 2
3A
Make sure there is NOT a
nut insert in the location specified.
2G
HJ
3A
HA
Caution:
Make sure there
is NOT a nut
insert here
11
3
Parts for this Step are Located in Bag 1 and Box 3
HJ x 8
Insert the Ladder Side Pole
(3B) and the Cargo Side
Pole (3C) into the other end
of the Swing Bar (B1).
HL x 4
HF x 4
Make sure the Poles
are oriented as shown,
and that there is a nut
insert in the location
specified.
HF
Six holes
face out
HJ HL
HJ
3B
HJ HL
HJ
HF
Caution:
Make sure there
is a nut insert here
B1
HJ
3C
4
Parts for this Step are Located in Box 2
Attach the 45” D-Tube (2D) to the Ladder and Cargo Side Poles (3B, 3C)
as shown. Make sure the flat and round sides of the D-Tube are oriented as
shown.
HJ x 2
HA x 2
3B
2D
Round Side
HA
3C
Flat Side
12
HL
HJ
HF
The holes
must face out
HJ
HJ
HF
HL
HJ
5
CH x 2
CA x 2
Insert D-Tube End Caps (CH) into each end of the 45” D-Tube (2D). Place
Hole Caps (CA) in the locations shown to keep the D-Tube End Caps (CH)
in place.
CH
CH
CA
CA
2D
CA
CH
SB x 6
SA x 6
SD x 12
SE x 12
SC x 6
6
Attach the Swing hardware to the Swing Bar (B1) while the A-Frame is still on the ground. Do not over tighten.
B1
SB
SD
SC
SD
SE
SE
SB
SD
SC
SD
SE
SE
SA
SA
13
7
Using at least two people, slowly
rotate the A-Frame assembly upright.
Two people
are required
for this step.
Parts for this Step are Located in Box 2 and 3
8
HJ x 2
Attach the 41” D-Tube (2E) to the Left Vertical Pole (3H) and Right
Vertical Pole (3G) and secure with the hardware shown using an
Equal Length Allen Wrench (HT). Make sure the flat and round sides
of the D-Tube are oriented as shown.
Flat Side
HA x 2
2E
Holes closest
to the flat edge
face up
3G
Round Side
3H
Inserts must
face up and out
Inserts must be
on same end
Stick
er is
HA
HJ
14
HT
loca
ted h
5 holes on
each pole face
each other
ere.
9
Parts for this Step are Located in Box 2
Attach Cross Braces (2H) between the 41” D-Tube (2E) and the Left
and Right Vertical Poles (3H, 3G).
HJ x 4
HA x 4
2H
2E
2H
3G
3H
Sti
cke
r is
loc
ate
dh
ere
.
HA
HJ
HJ
HA
10
CH x 2
CB x 4
CA x 2
Insert D-Tube End Caps (CH) into each end
of the 41” D-Tube (2E). Place Hole Caps
(CA) in the locations shown to keep the DTube End Caps (CH) in place. Insert 3” Flat
Round Caps (CB) into the top and bottom of
each Vertical Pole (3H, 3G). CB
CA
CH
CB
CA
2E
3G
CH
CB
3H
Stic
ker
is lo
cate
dh
ere
.
CB
15
11
Parts for this Step are Located in Box 3
HJ x 1
Place the Angled Ladder
Cap (CG) on the Angled
Cargo Net Leg (3E).
CG x 1
HE x 1
Attach the Angled Cargo Net Leg (3E) to the
Cargo Side D-Tube (3F) as shown in the
image below. A hole has been drilled for the
placement of the Angled Cargo
3F
Net Leg (3E). Secure with the
hardware shown.
CG
3E
3E
HJ
The 2 1/2” Bolt (HE) and 1/4” Zinc
Washer (HJ) should be on the outside of the Cargo Side D-Tube (3F)
as shown in the image.
HT
Do not over tighten, over tightening
may result in bending the D-Tube.
NOTE: Set aside the assembly
completed in this step. It will be
used in step 14.
16
HE
12
Stand the Left and Right Vertical
Poles (3H, 3G) up next to the
side of the A-Frame assembly
with the 45” D-Tube (2D).
3G
3H
Three people
are required
for this step.
2D
Parts for this Step are Located in Box 2
13
HJ x 2
Attach the Ladder Side D-Tube (2F) as shown. The
flat side of the D-Tube should face up.
HA x 2
Three people
are required
for this step.
HJ
HA
2F
HJ
HA
17
14
Parts for this Step are Located in Box 3
HJ x 2
Attach the assembly from step
11 as shown. The flat side of
the D-Tube faces up.
HA x 2
Three people
are required
for this step.
3F
HA HJ
3E
HA
HJ
15
Parts for this Step are Located in Box 2
HJ x 4
Attach the Cross Braces (2H) on to the Ladder
Side and Cargo Side D-Tubes (2F, 3F).
HA x 4
3F
2F
CA x 2
CH x 2
Insert D-Tube End Caps (CH) in the ends of the D-Tubes.
Place the Hole Caps (CA) in the locations shown.
2H
3F
2H
CA
CH
HA
2F
HJ
CH
HJ
HA
18
CA
16
Parts for this Step are Located in Box 2
HJ x 4
Attach the Deck Support (2C) to the D-Tubes as shown and secure with
the hardware indicated.
Two people
are required
for this step.
HA x 4
2C
The hook for the
under-deck swing
should face down
as shown
HJ
HA
HJ
HA
Parts for this Step are Located in Box 1 and 2
17
CF x 2
Straighten out the ropes of the Cargo Net
(1F), and slide the Cargo Net up the angled
poles on the play set. The large loops go on
the sides and the small loops go at the top
and bottom.
Do not attach the top loops of the Cargo
Net (1F) to the hooks on the back side of
the Cargo Side D-Tube (3F) at this time.
Place the Cargo Net Pole Cap
(CF) on each end of the Cargo
Net Bottom Pole (2L).
Slide the Cargo Net Bottom
Pole (2L) through the bottom
loops of the Cargo Net (1F).
Two people
are required
for this step.
CF
1F
2L
2L
CF
19
HJ x 2
HG x 2
CD x 2
18
Secure the Cargo Net Bottom Pole (2L) to the angled poles with the
4” Bolt (HG) going through the Angled Foot Caps (CD) as shown.
HG HJ
Two people
are required
for this step.
2L
HJ
HG
CD
1F
CD
Attach the top
loops of the Cargo Net
(1F) to the hooks on the back
side of the Cargo Side D-Tube (3F).
19
Parts for this Step are Located in Box 3
HJ x 1
CG x 1
Place the Angled Ladder Cap (CG)
over the Angled Ladder Leg (3D) and
secure to the Ladder Side D-Tube
(2F) with the hardware shown.
HE x 1
2F
CG
HE
3D
20
HJ
20
Parts for this Step are Located in Box 1
Attach the two Ladder Rungs (1C) to the Angled Ladder Leg (3D) and the
Ladder Side Pole (3B) as shown.
HO x 8
Do not tighten the hardware until both Ladder Rungs are in place.
HO
HO
HO
HO
3B
1C
3D
HO
HO
1C
HO
HO
21
Attach the Angled Foot Caps (CD) and then the
Hole Caps (CA) to the Ladder Poles as shown.
Two people
are required
for this step.
CA x 4
CD x 2
CA
CA
CD
21
22
CA x 4
Attach the Angled Foot Caps (CD) and then the Hole
Caps (CA) to the A-Frame Poles (3A) as shown.
CD x 2
Two people
are required
for this step.
CA
CA
3A
3A
CD
23
Parts for this Step are Located in Box 2
Place the Deck (2A) on top of the Deck Support (2C) as shown.
2A
If there are pre-drilled
holes in the deck, make
sure they are located
in the position shown.
This is where the slide
will be placed.
22
24
CE x 6
Secure the Deck (2A) by inserting 1 1/4” Bolts (HB) through the 1 1/2”
Square Caps with Holes (CE) and into the Deck.
HB x 6
WARNING
Do not stand in the Clubhouse until
the floor is completely attached.
2A
HB
CE
HB
CE
To make sure the Deck is properly
aligned, hand-tighten the Bolts until
all hardware has been installed, then
completely tighten all the Bolts.
23
25
Parts for this Step are Located in Bag 3 and Box 3
Place a Climbing Wall Panel (B3) on the ground, or in a safe
drilling position. The indentations in the Climbing Wall indicate
the locations needed to be drilled. Using a 1/4” Drill Bit (not
included), drill completely through the plastic.
CJ x 2
HO x 5
Repeat this step to drill through the indentations in the other Climbing Wall Panel (B3).
B3
NOTE: The panels have five indentations on
each side for a total of 10 indentations per panel.
Make sure to drill through all 20 indentations.
Caution:
Make sure to drill holes
at the angle shown
CJ
Place the Climbing Wall Pole (3K) into
one of the notches on the Climbing Wall
Panel as shown. Secure the Pole to the
Climbing Wall with the hardware shown.
Place a Flat Black Cap (CJ)
in each end of the Climbing
Wall Pole (3K).
NOTE: Both Climbing Wall Panels
are the same. Mount the panels so
that the large openings are opposite.
3K
3K
B3
3K
CJ
HO
HO
CJ
HO
HO
HO
24
26
Place the Climbing Wall Panel (B3) that is
attached to the Climbing Wall Pole (3K) in
the location shown. Make sure the
B3
Climbing Wall Panel is oriented
as shown.
HO x 5
3G
Secure the Climbing Wall
Panel (B3) to the Right Vertical
Pole (3G) with the hardware
shown.
Two people
are required
for this step.
Top View
HO
3K
27
Parts for this Step are Located in Bag 3
Place the other Climbing Wall
Panel (B3) that is not attached
to the Climbing Wall Pole (3K)
in the location shown.
B3
Make sure the Climbing Wall
Panel (B3) is oriented as
shown in the image below.
Two people
are required
for this step.
Top View
3K
Large Openings
Opposite
B3
NOTE: Mount the panels so that the
large openings are opposite.
25
28
HO x 5
Secure the Climbing Wall Panel (B3) to the Climbing Wall Pole (3K) with the hardware
shown.
Two people
are required
HO
for this step.
3K
HO
B3
HO
HO
HO
HO
29
Secure the Climbing Wall Panel
(B3) to the Left Vertical Pole
(3H) with the hardware shown.
Two people
are required
for this step.
HO x 5
HO
B3
3H
HO
3H
B3
HO
HO
HO
HO
26
30
Parts for this Step are Located in Box 3
HJ x 2
Place the Climbing Wall Roof Tube (3J) in the location shown,
and secure it to the Right and Left Vertical Poles (3G, 3H ) with
the hardware shown.
HD x 2
3G
3J
3H
HJ
HD
HJ
HD
Make sure the nut
insert is located in the
orientation shown.
31
Parts for this Step are Located in Box 3
HJ x 1
Place the A-Frame Roof Tube (3I) in the location shown, and
secure it to the Swing Bar (B1) with the hardware shown.
3I
HD x 1
B1
Make sure the nut
inserts are located in
the orientation shown.
HJ
HD
27
32
Parts for this Step are Located in Box 1
HJ x 8
Attach the One Handle Rails (1A) to the Clubhouse by placing the bottom of
the rails over the 1 1/2” Square Caps with Holes (CE) as shown. Secure the
top of the rails to the Climbing Wall and A-Frame Roof Tubes (3J, 3I).
3J
HA x 8
1A
3J
HJ
HJ
HA
HA
CE
1A
CE
Parts for this Step are Located in Box 2
33
HJ x 4
Place a Square Black Cap (CI) in each end of the Roof
Railings (2K).
CI x 4
CI
2K
CI
HA x 4
Place the Roof Railings (2K) over the One Handle Rails (1A) installed
in the previous step, and secure it to the One Handle Rails as shown.
2K
2K
1A
1A
1A
HJ
HA
28
34
Parts for this Step are Located in Box 1
Attach the Two Handle Rails (1B) to the Clubhouse by placing the bottom of
the Rails over the 1 1/2” Square Caps with Holes (CE) as shown. Secure the
top of the rails to the Roof Railings (2K) with the hardware shown.
HJ x 4
HA x 4
2K
1B
HJ
HJ
HA
HA
CE
35
Parts for this Step are Located in Box 2
Secure the Round Roof Tubes (2J) to the
A-Frame and Climbing Wall Roof Tubes (3I,
3J). Secure the Round Roof Tubes with the
hardware shown using the Equal Length Allen
Wrench (HT) as shown.
HJ x 4
CA x 4
HS x 4
CI x 4
2J
2J
HJ
HS
Place a Square Black Cap (CI)
in each end of the Roof Tubes
(2J), then place the Hole Caps
(CA) in the locations shown.
CA
CI
HT
29
36
Parts for this Step are Located in Box 2
HJ x 2
Connect two Roof Trusses (2I)
together as shown.
HM x 1
HA x 1
Repeat this step to connect
the other six Trusses.
2I
2I
The holes in the
trusses need to
face up.
HM
HJ
HJ
HA
37
Place the Roof Trusses assembled in step 36 on the Round Roof Tubes (2J) as shown,
and secure with the hardware shown using the Equal Length Allen Wrench (HT).
HA x 8
HA
2J
2J
HT
30
38
Parts for this Step are Located in Box 4
Attach the Roof Panels (4A) to the Roof Trusses, and secure the
panels as shown. The notch at the top of the panel will line up with the
top of the Trusses.
To prevent the Screws
from going through
the plastic, do not
overtighten.
HP x 48
4A
The Roof Panels (4A) placed on
top need to have a notch as shown.
HP
HP
HP
HP
HP
HP
4A
HP
HP
HP
HP
HP
HP
CAUTION
Exercise extreme caution
while using a ladder for
assembly. Follow all warnings
and instructions provided by
the ladder manufacturer.
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
HP
31
39
Insert 1 1/2” Dome Caps (CC) into
the ends of the Roof Trusses.
CC x 8
CC
CC
CC
CC
40
Parts for this Step are Located in Bag 2
Using a 3/8” Drill Bit (not included), drill 3/8” holes through the
indentations in the top of the Slide (B2) as shown. Drill the holes
directly downward.
B2
32
41
Note: If the deck does not have
pre-drilled holes, complete this step.
Use a 3/8” Drill Bit to drill through the
Deck (2A) in the Slide location.
2A
View from underneath Deck
42
Parts for this Step are Located in Bag 2
Place the Slide (B2) in the location shown, and attach it
to the Deck (2A) with the hardware indicated.
HJ x 6
HL x 3
HB x 3
HB
HB
HB
HJ
HJ
2A
HJ
B2
HJ
HL
HJ
HL
HJ
HL
33
43
Parts for this Step are Located in Box 2
HP x 2
HK x 2
Place the Chalkboard (2B) between the Deck (2A) and the
A-Frame Roof Tube (3I). Secure the bottom of the Chalkboard
with two 1 1/4” Screws (HP). Make sure there are two Spacers
(HK) between the Chalkboard and the Pole on each side.
HO x 3
3I
3I
HO
2B
HO
HO
HK
HP
Attach the top of the Chalkboard
with three 3/4” Screws (HO).
2A
Bottom of Chalkboard-complete for both sides
44
Parts for this Step are Located in Box 1
HJ x 3
Attach the Binocular Bracket
(1H) to the Climbing Roof
Tube (3J), and secure with
the hardware shown.
HA x 1
Do not over tighten the
hardware. The Binoculars
will not be able to rotate.
HL x 1
HE x 1
Attach the Binoculars (1G) to the Bracket (1H)
with the hardware shown.
HA
HJ
1H
1G
3J
HE
HJ
HJ
HL
3J
34
45
Parts for this Step are Located in Box 1
Slide the Hex Bolt (HH) into the center
hole of the Wheel Clicker (1J) as shown.
HH x 1
HC x 2
1J
HH
3I
1J
HC
HC
Attach the Wheel Clicker (1J) to
the A-Frame Roof Tube (3I) and
secure with the hardware shown.
46
Parts for this Step are Located in Box 1
HR x 1
HN x 1
1I
1J
1I
HR
HN
Place the Steering
Wheel (1I) over the
Wheel Clicker (1J)
as shown.
1K
Secure the Steering Wheel (1I)
to the Wheel Clicker (1J) with the
hardware shown.
Do not overtighten the
hardware. The Steering Wheel
will not be able to rotate.
Insert the Wheel Cap
(1K) into the front of
the Wheel (1I).
35
47
Parts for this Step are Located in Box 2
Place the Square Black Cap (CI) into each
end of the Square Tubing (2N)
HI x 3
Place the Plastic Seat (2M) on top of the
Square Tubing (2N) and secure with the
hardware shown.
CI x 6
Repeat this step to assemble the two other
Plastic Seats (2M) to the Square Tubings (2N).
HI
2M
2N
CI
2N
CI
48
Parts for this Step are Located in Box 2
HJ x 3
Bring the three assemblies completed in step
47 together.
HL x 6
HE x 6
HE
HE
HE
Secure the assemblies together using the
3- and 6-Hole Brackets (2O, 2P) and the
hardware shown.
2P
2O
HE
HE
HE
CK
HL
HL
Finish the Under-Deck Swing by placing the UnderDeck Cap (CK) on top of the 6-Hole Bracket (2P),
and securing it with the hardware shown.
2P
HJ
HJ
HJ
HL
HL
36
HL
HL
49
Parts for this Step are Located in Box 2
Attach the Quick Links (HQ) to each end of the Soft Grip
Chains (2Q). Attach the Soft Grip Chains (2Q) to the
Under-Deck Swing.
HQ x 6
HQ
HQ
HQ
2Q
2Q
2Q
HQ
HQ
HQ
50
Attach the completed Under-Deck Swing to the hooks
located under the Deck with the Quick Links (HQ) as shown.
Note: If the Under-Deck Swing is not level, adjust the links
by attaching the second chain link to the Quick Link. Do this
to the lowest part of the swing.
HQ
2Q
37
51
Parts for this Step are Located in Box 1
Attach the Swings (1D) and Trapeze (1E) to the Swing
hardware already attach to the Swing Bar (B1).
1E
1D
1D
38
If the warning sticker is illegible, destroyed or removed,
contact Customer Service for a replacement.
WARNING
This product is intended for use by children
ages 3 to 12, and is for residential use only.
Do not install over concrete, asphalt, packed
earth, or any other hard surface. A fall onto a
hard surface can result in serious injury.
Observing the following statements and warnings
reduces the likelihood of serious or fatal injury:
• On-site adult supervision should be provided for
children of all ages.
• Children should not walk close to, in front of, behind,
or between moving items.
• Instruct children not to twist swing chains or ropes
or loop them over the top support bar since this may
reduce the strength of the chain or rope.
• Instruct children to avoid swinging empty seats.
• Teach children to sit in the center of the swings with
their full weight on the seats. Never stand, sit or kneel
on the swing seat.
• Instruct children not to use the equipment in a manner other than intended.
• Instruct children not to get off equipment while it is in
motion.
• To prevent entanglement and strangulation, dress
children appropriately using well-fitting shoes and avoiding ponchos, scarves, jackets with neck drawstrings,
helmets with straps, and other loose-fitting clothing that
is potentially hazardous while using equipment.
• Instruct children not to climb when the equipment is
wet.
• Instruct children not to attach items to the playground
equipment that are not specifically designed for use with
the equipment, such as, but not limited to, jump ropes,
clothesline, pet leashes, cables and chain as they may
cause a strangulation hazard.
• Make sure guardrails are in place at all times.
ADVERTENCIA
AVERTISSEMENT
Este producto es para niños de 3 a 12 años de
edad. Este producto es para uso residencial
únicamente. No lo instale sobre concreto,
asfalto, tierra empaquetada o cualquier otra
superficie dura. La caida sobre una superficie
dura podría ocasionar serias lesiones.
Ce produit est conçu pour un usage par des
enfants âgés de 3 à 12 ans. Ce produit est réservé
à un usage personnel seulement. Ne pas installer
sur du béton, de l’asphalte, de la terre compactée
ou toute autre surface dure. Une chute sur une
surface dure peut entraîner des blessures graves.
Si se presta atención a los siguientes enunciados y
avisos de advertencia se reduce la probabilidad de
producirse lesiones serias o mortales:
L’observation des déclarations et des avertissements suivants réduit les risques de blessures
graves ou fatales:
• Los niños de todas las edades deben estar bajo la
supervisión de un adulto en el lugar.
• Los niños no deben caminar junto, en- frente, detrás de
o entre las piezas móviles.
• Indique a los niños no torcer las cadenas o sogas de los
columpios ni pasarlas por encima de la barra de soporte
superior, ya que puede reducirse la resistencia de las
cadenas o sogas, según sea el caso.
• Indique a los niños que eviten impulsar columpios vacíos.
• Enseñe a los niños a sentarse en el centro de los
columpios, con todo su peso en los asientos. Nunca deben
pararse ni hincarse en el asiento del columpio.
• Indique a los niños no usar el equipo de ninguna forma
diferente a la indicada.
• Indique a los niños no bajarse del equipo cuando esté
en movimiento.
• Para evitar la posibilidad de que los niños se enreden y
estrangulen, vístalos debidamente con zapatos debidamente ajustados y sin ponchos, bufandas, chamarras con
cordones de apriete en el cuello, cascos con correas y
otras ropas holgadas que puedan ser peligrosas al usar el
equipo.
• Indique a los niños no subirse cuando esté húmedo el
equipo.
• Indique a los niños no adherir al equipo de patio de
juegos objetos no diseñados específicamente para éste,
como cuerdas de saltar, cuerdas de tendedero de ropa,
correas de mascotas, cables y cadenas, ya que podrían
causar un peligro de estrangulación.
• Asegúrese de que los rieles protectores estén colocados en su lugar todo el tiempo.
• La présence d’un adulte surveillant les enfants de tous âges
doit être assurée.
• Veiller à ce que les enfants ne marchent pas près, devant,
derrière ou entre les éléments en mouvement.
• Veiller à ce que les enfants ne tordent pas les chaînes ou
cordes de la balançoire. De même, veiller à ce que les enfants
ne bouclent pas les chaînes ou les cordes au-dessus de la
barre de support supérieure, car cela pourrait en réduire leur
solidité.
• Veiller à ce que les enfants ne balancent pas les sièges
vides.
• Veiller à ce que les enfants s’assoient au centre des sièges
de la balançoire, avec leur plein poids sur le siège. Veiller à ne
jamais s’asseoir, s’agenouiller ou se tenir debout sur le siège.
• Veiller à ce que les enfants n’utilisent pas l’équipement à
d’autres fins que pour l’usage prévu.
• Veiller à ce que les enfants ne descendent pas de
l’équipement lorsqu’il est encore en mouvement.
• Pour éviter l’emmêlement des cordes et des chaînes et
ainsi éviter tout risque d’étranglement, veiller à habiller les
enfants correctement. Utiliser des souliers bien adaptés. Ne
pas mettre des ponchos, foulards, blousons avec des cordons
près du cou, casques avec des sangles et tout autre vêtement
ample pouvant potentiellement s’avérer dangereux lors de
l’utilisation de l’équipement.
• Veiller à ce que les enfants ne grimpent pas sur
l’équipement quand celui-ci est mouillé.
• Veiller à ne pas attacher d’objets sur l’équipement de jeu
non spécifiquement conçus pour cet équipement, tels que,
mais sans s’y limiter, cordes à sauter, cordes à linge, laisses
d’animaux, câbles et chaînes. Ceux-ci posent un risque
d’étranglement.
• S’assurer que des garde-fous sont en place en tout temps.
Lifetime Products, Inc
Clearfield, UT 84016
www.lifetime.com
1/05/2009
# 1049933
39