Download User`s Guide

065-1050GSFP PoE Media Converter
10/100/1000BaseT/TX to 1000Base SFP
(IEEE 802.3af/at PSE)
FCC Warning
Package Contents
This device has been tested and found to comply with
limits for a Class B digital device, pursuant to Part 2 and
15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates and radiates radio frequency
energy and, if not installed and used in accordance with
the user’s manual, it may cause interference in which case
users will be required to correct interference at their own
expenses.
Before you start to install this Media Converter, please verify
your package that contains the following items:
CE Warning
This is a Class B product. In a domestic environment, this
product may cause radio interference in which case
the user may be required to take adequate measures.
Quick Installation Guide
Introduction
The Signamax 065-1050GSFP PoE Gigabit Ethernet
Media Converter is designed to bridge a 10BaseT,
100BaseTX, or 1000BaseT copper connection to a
1000Base SFP fiber optic module. It’s used to extend the
distance connection between two twisted-pair devices at
Gigabit Ethernet speed via the fiber cable transparently,
with no performance degradation.
This PoE PSE Gigabit Ethernet Media Converter is
based on a switching hub design. It can support
Auto-Negotiation and Flow Control functions on the
twisted-pair port.
There are two kinds of PoE Media Converter - PSE and
PD.
A. PSE - Power sourcing equipment is a device
providing power to a PoE Powered Device
(PD).
(The 065-1050GSFP supports either IEEE
802.3at or IEEE 802.3af PDs.)
B. PD - Powered device is a device powered by a
PSE.
(IEEE 802.3af or IEEE 802.3at Powered
Devices are supported by the
065-1050GSFP.)
 One 065-1050GSFP PoE Media
 One Quick Installation Guide
 One Power Adaptor 48V / 0.83A
 One AC power cord
converter
Key Features
 Compliant with IEEE 802.3 10BaseT, IEEE 802.3u
100BaseTX, IEEE 802.3 1000BaseT, IEEE 802.3z
1000BaseSX/LX and IEEE 802.3af/at Standards.
 1x 10/1001000BaseT/TX Ethernet TP Port and 1x
1000Base SFP Ethernet Fiber Receptacle.
 TP port is a PSE port, providing power to a PD device.
(Max. 30W)
 TP Port can support Half/Full-Duplex
Auto-MDI/MDI-X and Auto-Negotiation.
 Supports Link Fault Signaling (LFS) Function. LFS is
switchable on/off via a side panel-mounted slide
switch.
 The 1000Base Fiber Port can support either
Multimode or Singlemode fiber, depending upon the
SFP fiber module selected.
Connection
Technical Specifications
Storage
Temperature
IEEE 802.3at PoE+ (PSE
converter)
IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.3ab 1000BaseT
IEEE 802.3z 1000BaseSX/LX
1 x 10/100/1000BaseT/TX with
RJ-45
Connector and PSE function
1 x 1000Base SFP Fiber Module
Receptacle
Gigabit Ethernet:
1000 Mbps/Half-Duplex
2000 Mbps/Full-Duplex
10/100/1000BaseT/TX :
Cat. 5e UTP/STP or above, up to
100 m
1000BaseX:
Multimode: 50/125μm or
62.5/125μm fiber optic cable
Singlemode: 9/125μm or
10/125μm fiber optic cable
RJ45: 100M/Act, 1000M/Act
SFP : Link/Act
System: Power
Input: 100 to 240 V AC, 0.8 A
Max.
Output: DC +48 V / 0.83 A
6 Watts (Max, converter circuitry
only), plus the PoE/PoE+ power
required to support the
connected PD.
4.02 x 2.96 x 0.91 inches
102 x 75 x 23 mm (L x W x H)
0.51 lbs.
230 g
32°F to 113°F
0°C to 45°C
-4°F to 194°F
-20°C to 90°C
Humidity
10 to 90% RH (non-condensing)
Certifications
FCC, CE
tandards
Ports
Data Transfer
Rate
Installation
I. TP port (RJ-45)
The TP port of this converter supports 10BaseT,
100BaseTX, or 1000BaseT, with Auto-Negotiation,
Auto MDI/MDI-X, Flow control and Power over Ethernet
PSE functions. It supports cable lengths of up to 100
meters for Cat 5, 5e or 6 cables.
II. Fiber Port
The fiber port supports multimode or singlemode fiber optic
cables.
III. DIP Switch Setting: (LFS ON/OFF)
Users can have the LFS function turned ON or OFF by a
slide switch at the right side of the converter. The factory
default is LFS OFF.
Transmission
Media
Led
Indicators
Power
Supply
(included)
Power
Consumption
Dimensions
Weight
Operating
Temperature