Download DT-TPS User Manual
Transcript
DT-TPS telephone interface User Manual Please read this manual carefully before using the product you purchase, and keep it well for future use.We reserve the right to modify the specification in this manual at any time without notice. 1 About TPS Unit Discription: The TPS unit is a telephone converter designed for DT 2-wire system to divert calls from outdoor station to telephone or mobile phone.With TPS unit,you can communicate with outdoor visitor by your telephone or mobile phone which just like a remote control,you can do the operation of talking,unlock and so on. Features: 72 mm 90 mm • Maximum 3 telephone numbers can be set on monitor. • Must be with Call Transfer function for monitor • Divert Calls from monitor to telephone via TPS ,the TPS is like a telephone,when setting the diversion function,door station calls TPS first,then divert to the telephone number you set. • Application:villa and apartment 60 mm 1. Terminal Introduction 1 2 3 4 5 6 ON DIP DIP: 485 PORT: BUS(IN): BUS(OUT): TEL: PBX: 485 PORT BUS(IN) BUS(OUT) TEL PBX DIP switches,DIP settings refer to 3. 485 connection port,used to update the software for TPS. Input port,connect to power supply. Output port,connect to Monitor. Connect to the telephone. Connect to the telephone network. 2 Configuration: LED BUTTON Power Network Reset Signal Quality Status Transfer Recover Test * The instructions of indicator: LED indicator Power Descriptions -LED off When the TPS not working -LED flashes rapidly when the system error -Always on when the TPS work normally Network Status -Always on when the TPS kits work normally -LED flashes one time when the system receives the effective instruction -LED off When there is no call transfer -LED flashes slowly when the TPS in the transfer waiting state Transfer -LED flashes 3 times rapidly when the TPS transfer failed -Always on when the system in the talking state * LED flashes one time when its settings are being restored to default 3 * The instructions of button: Button Reset Signal Quality Recover Test Descriptions -Press Reset button for 3 seconds,it will restart the TPS. -Reserved -Press Recover button for 3 seconds, its settings will be restored to default -Reserved 2. Mounting Step1: Mount the din rail to the wall with screws ; Step2: Pull down the mounting buckle,then hang the unit on din rail. Din rail Din rail Mounting Buckle 4 3. DIP Switches Setting for TPS Bit DIP1 Bit State Description 1 2 3 4 5 6 Set to OFF, the TPS no connection. 1 2 3 4 5 6 Set to ON, DT system connected telephone network via local switch. 1 2 3 4 5 6 Set to OFF, the TPS no connection. ON ON DIP2 ON Set to ON, DT system connected telephone network directly. 1 2 3 4 5 6 ON DIP3 Door Station speaker adjust—set to OFF, the volume is normal. 1 2 3 4 5 6 ON Door Station speaker adjust—set to ON, the volume is twice louder than normal. 1 2 3 4 5 6 ON DIP4 1 2 3 4 5 6 Door station micphone adjust—set to OFF, the volume is normal. 1 2 3 4 5 6 Door station micphone adjust—set to ON, the volume is twice louder than normal. 1 2 3 4 5 6 Reserve 1 2 3 4 5 6 Set to OFF, it shows the system is villa. 1 2 3 4 5 6 Set to ON, it shows the system is partment. ON ON DIP5 DIP6 ON ON ON Note: DIP1 and DIP2 can not be "on" state at the same time. DIP3 and DIP4 can not be "on" state at the same time. 4.Telephone Number Setting on Monitor Touch screen monitors: -Telephone Number- 1 2 3 1> _ 4 5 6 2> _ 7 8 9 3> _ 0 Don’t divert calls Divert if not answered Divert simultaneously Exit&save Exit&Unsave • Maximum 3 telephone numbers can be set,touch the telephone number frame,then input the the number by touching the digital keypad. 5 Button operation monitors: GSM configure 1) 0 2) 3) 4)Divert mode select: 2 0:Not 1:Not Answer 2:Simulateously Cancel Edit Save&Exit • Maximum 3 telephone numbers can be set,Use ▲ /▼ Button to move upward / downward to select the item,then press the MENU button to edit.Use ▲ / ▼ Button to increase / decrease the value,and use button to input next digital,use button to button to cancel the input. press the MENU button again to finish the edit operation. Note: • There are 3 types of divert modes: • 1:Don't divert calls----calls from outdoor station will not be diverted. • 2:Divert if not answered----outdoor station calls indoor monitor firstly,if nobody answer the call within 25 seconds,the call will be diverted to the telephone number you set. At this mode,the monitor will shut off immediatelly when TPS deverts sucessfully,while it won't affect the communication between TPS and outdoor station.Otherwise, the monitor can do the operation of monitoring,talking,and unlocking. • 3:Divert simutaneously----calls from outdoor station will be diverted to your telephone immediately.At this mode,the monitor won't shut off when TPS deverts sucessfully,but if the monitor answers the call at this time,TPS will quit absolutely. 6 5.Operation Instructions Note: Divert function is activated in the following instructions Item Discription Unlocking • Input 1# on your telephone or mobile phone to release the first lock • Input 2# on you telephone or mobile phone to release the second lock Hanging up • Input 9# on your telephone or mobile phone to hang off absolutely Calling next telephone number • 1:At least 2 telephone numbers must be set on monitor • 2:During communication between telephone and outdoor station,"#" button has not been input on telephone and the calling time of each group number is less than 80 seconds. Calling slave telephone • Add a letter "P" between master telephone and slave telephone.The TPS will call the slave telephone directly. 7 6.Wiring Basic in-out mode(for villa) ON CALL UNLOCK TALK/MON 1 2 3 4 5 6 IN-USE Code=14, DIP-6=off ON CALL UNLOCK TALK/MON 1 2 3 4 5 6 IN-USE Code=13, DIP-6=off ON CALL UNLOCK TALK/MON IN-USE 1 2 3 4 5 6 Code=0, DIP-6=off to telephone to telephone network DPS TPS PS4 AC~ 1 23 4 5 6 ID=00 ON ON DIP6=off 1 2 Note:The TPS unit occupies a user code of 15 8 Star wiring mode(for villa) ON CALL IN-USE UNLOCK TALK/MON 1 2 3 4 5 6 IN-USE Code=13, DIP-6=on A B C D Code=14, DIP-6=on ON ON IN-USE DIP=on,off,off UNLOCK TALK/MON 1 2 3 4 5 6 IN-USE Code=11, DIP-6=on CALL UNLOCK TALK/MON CALL ON UNLOCK TALK/MON IN-USE Impedance switch IN-USE 1 2 3 4 5 6 Code=3, DIP-6=on Code=2, DIP-6=on A B C D 1 2 3 4 5 6 ON CALL UNLOCK CALL ON Code=1, DIP-6=on DIP=on,off,off UNLOCK TALK/MON TALK/MON IN-USE IN-USE 1 2 3 4 5 6 OFF ON DBC4S Code=12, DIP-6=on ON OFF ON CALL CALL UNLOCK TALK/MON 1 2 3 4 5 6 Impedance switch CALL UNLOCK TALK/MON DBC4S ON 1 2 3 4 5 6 1 2 3 4 5 6 Code=0, DIP-6=on 1 23 4 5 6 ON DIP6=off DPS TPS PS5 85~260AC ID=00 ON 1 2 Note:The TPS unit occupies a user code of 15 9 Basic in-out mode(for apartment) ON CALL UNLOCK TALK/MON 1 2 3 4 5 6 IN-USE Code=32, DIP-6=on ON CALL UNLOCK TALK/MON IN-USE 1 2 3 4 5 6 Code=31, DIP-6=off ON CALL UNLOCK TALK/MON 1 2 3 4 5 6 IN-USE Code=1, DIP-6=off TPS 1 23 4 5 6 ON Code=1,DIP6=on to telephone network to telephone PS5 DPS 85~260AC ID=00 123456 ON 8 Basic star wiring mode(for apartment) ON ON CALL Impedance switch CALL UNLOCK UNLOCK OFF ON TALK/MON TALK/MON IN-USE IN-USE ON CALL CALL DIP=on,off,off UNLOCK UNLOCK TALK/MON TALK/MON IN-USE IN-USE 1 2 3 4 5 6 1 2 3 4 5 6 Code=29, DIP-6=on Code=30, DIP-6=on ON Impedance switch ON CALL CALL UNLOCK UNLOCK TALK/MON TALK/MON 1 2 3 4 5 6 IN-USE 1 2 3 4 5 6 Code=4, DIP-6=on IN-USE A B C D Code=3, DIP-6=on ON ON CALL CALL DIP=on,off,off UNLOCK UNLOCK TALK/MON TALK/MON 1 2 3 4 5 6 OFF ON DBC4S ON A B C D Code=31, DIP-6=on DBC4S 1 2 3 4 5 6 1 2 3 4 5 6 Code=32, DIP-6=on IN-USE 1 2 3 4 5 6 IN-USE Code=2, DIP-6=on Code=1, DIP-6=on 1 23 4 5 6 ON DIP6=off DPS TPS PS5 85~260AC ID=00 123456 ON 7.Specification Power input: Power Consumption: Working temperature: Wiring: Dimension: DC 20~28V Standby(26V):30mA;working(26V):80mA -10ºC +40ºC 2 wire,non-polarity 90(H)X72(W)X60(D)mm The design and specifications can be changed without notice to the user. Right to interpret and copyright of this manual are preserved. DT-ENG-TPS Versions1.0