Download ELVIS Series - Le Manoir Pub

User's Manual
ELVIS Series
SEKAKU ELECTRON IND. CO., LTD
NO.1, LANE 17, SEC. 2, HAN SHI WEST ROAD, TAICHUNG, 401 TAIWAN
http://www.altoproaudio.com
Tel:886-4-22313737
email: [email protected] Fax:886-4-22346757
All rights reserved to ALTO. All features and content might be changed
without prior notice. Any photocopy, translation, or reproduction of part of this
manual without written permission is forbidden. Copyright 2003 Sekaku Electron
R
LTO
www.altoproaudio.com
Version 1.0 July 2003
English
ELVIS12SA
Output Power IHF
Output Power RMS
Max SPL at 1mt
Input Sensitivity
Input Impedance
Connectors
Subsonic Filter
Protections
External Control
Power Supply
Weight
Shipping
ELVIS15SA
250Watt IHF
180Watt RMS
121 dB ( IHF Power )
+ 4dB / 1,23V L -R IN / L -R OUT
30kOhms - In / 600Ohms - Out
L /Mono-R IN on XLR / L-R OUT on XLR
Electronic Crossover 125Hz at 24dB/oct.
Volume - Stereo/Mono&Ground Swicth
230Volt / 115Volt 50 / 60Hz
SAFETY INSTRUCTIONS
350Watt IHF
250Watt RMS
123 dB ( IHF Power )
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
"Electric discharge"
This symbol, alert you to the presence of uninsulated dangerous voltage inside the product enclosure, which constitutes a
risk of electric shock.
"Exclamatory point"
This symbol, alert the user to the presence of important operating and maintenance instructions in the owner's manual
included to the product.
1. Read Instructions
All the safety and operation instructions should be read before using the product and retain them for future reference.
2. Water & Moisture
This product should not be used near water and will be protect from atmospheric agents in fixed or temporary installations.
3. Heat
This product should be situated away from heat sources such as radiators, or other devices which produce heat.
4. Liquid Entry
Care should be taken so that liquids are not spilled into the product and that objects do not fall on.
5. Service Assistance
This product should be serviced only by qualified service personnel when :
a. Liquids has spilled or objects have fallen into this product, or
b. This product has been exposed to rain, or
c. This product does not appear to operate normally or exhibits change in performance, or has been dropped or its
cabinet / chassis damaged.
6. Package
The package of this product has been tested, inspect the package before open, if any damage is found, notify to
your dealer.
7. Hearing
This product produce high acoustic levels may cause permanent hearing loss, (SPL in for a defined period of time).
8. Installations
This product should be installed on the wall or in the floor with specific stands, according to the max weight.
12
1
TABLE OF CONTENT
5. ELVIS TECHNICAL SPECIFICATIONS
1. QUICK START - PASSIVE SPEAKER CABINET....................................................................................3
ELVIS10
-. For Passive Full-range Speakers
System type
Continuous power
Peak Power Rating
-. For Passive Subwoofer & Satellite Speakers
2. QUICK START - ACTIVE SPEAKER CABINET.....................................................................................5
-. For Active Full-range Speakers
Sensitivity (1W, 1m)
Frequency Response
Impedance
Crossover Frequency
Protection
Low-Frequency
-. For Active Subwoofer & Satellite Speakers
3. CONNECTION PLATE...........................................................................................................................7
-. PASSIVE FULL-RANGE Speaker for ELVIS10/ELVIS12/ELVIS15/ELVIS12M
-. PASSIVE SUBWOOFER Speaker for ELVIS12S/ELVIS15S
-. Active FULL-RANGE Speaker for ELVIS10A/ELVIS12/AELVIS15A/ELVIS12MA
High-Frequency
Spherical Wave Guide
Horn Coverage
Connectors(+1/-1)
Enclosure
Dimensions HxWxD
Weight lbs/kg
ELVIS12
2-way vented box
120W AES standard
240W Peak
96dB/116,5dB Max
65Hz/20kHz +/-6dB
8Ohm Nominal
2700Hz 12dB/oct
ELVIS15
ELVIS12M
2-way vented box
2-way vented box
2-way vented box
180W AES standard
360W Peak
250W AES standard
500W Peak
180W AES standard
360W Peak
97dB/119.5dB Max
98dB/122dB Max
60Hz/20kHz +/-6dB
50Hz/20kHz +/-6dB
8Ohm Nominal
8Ohm Nominal
2500Hz 12dB/oct
2200Hz 12dB/oct
Electronics High Frequencies Protection
97dB/119dB Max
75Hz/20kHz +/-6dB
8Ohm Nominal
2500Hz 12dB/oct
10"/266mm woofer
12"/318mm woofer
15"/318mm woofer
12"/318mm woofer
1" Compression Driver 1"Compression Driver
1"Compression Driver
1"Compression Driver
Custom Horn with Polypropilene Reinforced
80 H 80 V
80 H 80 V
80 H 80 V
80 H 80 V
2xSPK4 Input/Link @+1/-1 connected - +2/-2 not connected
Trapezoidal cabinet in 18mm particle board P.B. -Covered with resistant carpet -Black metal grille protection
580 345 305mm
635 405 340mm
700 455 370mm
615 400 345mm
36,6lbs/16,6kg
46lbs/20.8kg
57lbs/26kg
39.5lbs/18kg
Shipping
-. Active SUBWOOFER Speaker for ELVIS12SA/ELVIS15SA
4. WIRE CONNECTIONS .........................................................................................................................10
System type
Continuous Power
Peak Power Rating
-. For Passive Speaker Cabinets
Sensitivity (1W, 1m)
-. For Active Speaker Cabinets
Frequency Response
Impedance
5. ELVIS TECHNICAL SPECIFICATIONS.................................................................................................11
Crossover Frequency
Protection
Low-Frequency
ELVIS12S
ELVIS15S
vented box
200W AES standard
400W Peak
97dB/119dB Max
50Hz/20kHz +/-6dB
4Ohm Nominal
125Hz 6dB/oct
vented box
300W AES standard
600W Peak
98dB/122dB Max
45Hz/20kHz +/-6dB
4Ohm Nominal
125Hz 6dB/oct
12"/318mm woofer
15"/385mm woofer
2xSPK4 @ in/out
2xSPK4 @ in/out
High-Frequency
Spherical Wave Guide
Horn Coverage
Connectors (+1/-1)
Enclosure
Dimensions HxWxD
Weight lbs/kg
Shipping
Trapezoidal cabinet in 18mm particle board P.B. -Covered with resistant
carpet -Black metal grille protection
495x400x455mm
565x455x525mm
44lbs/20kg
54.5lbs/27kg
ELVIS10A
Output Power IHF
Output Power RMS
Max SPL at 1mt
Input Sensitivity
Input Impedance
Connectors
Subsonic Filter
Protections
External Control
Power Supply
Weight
Shipping
2
150Watt IHF
120Watt RMS
117,5 dB ( IHF Power )
30Hz - 24dB/oct.
ELVIS12A
ELVIS15A
ELVIS12MA
250Watt IHF
350Watt IHF
250Watt IHF
180Watt RMS
250Watt RMS
180Watt RMS
121 dB ( IHF Power )
123 dB ( IHF Power )
121 dB ( IHF Power )
+ 4dB / 1,23V
30kOhms Balanced - 15kOhms Unbalanced
Mic on XLR / Line Input on Combo / Mix Output on XLR
30Hz - 24dB/oct.
30Hz - 24dB/oct.
30Hz - 24dB/oct.
Soft - Start DC voltage protect compressor
Mic Gain - EQ-High-Mid-Low-Volume-Ground Switch
230Volt / 115Volt 50 / 60Hz
11
1. QUICK START - PASSIVE SPEAKER CABINET
4. WIRE CONNECTIONS
-. For Passive Speaker Cabinets
Please use only the power connectors to make connections with other signal source equipment for the passive speaker
cabinets. The power connector has four terminals: 1+, 1-, 2+, 2-.
-. For Passive Full-range Speakers
1). Connect one side of the speaker cable to the Output CHA/CHB or Binding Post of your stereo power amplifier
and the other side to the Input socket of your speaker cabinet.
1-
1+
2-
Make all initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely
down.
2+
2). Complete other connections as illustrated.
3). Turn on your mixer first, then the stereo power amplifier.
In our cabinets, only 1+/1- are used to connect the Speaker+/Speaker-, and 2+/2- are not used.
4). Turn up the volume controls of your amplifier to about 70%.
5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the output
level.
-. For Active Speaker Cabinets
As to these circumstances, audio connections is mostly intended for the signal flow, so, determine the wire configuration
according to your real application system and its connecting facility. Normally, you have the following choices:
6). After using, turn off your stereo power amplifier first, then the mixer.
Balanced
TIP RING SLEEVE
QUICK START
Tip
Ring
SLEEVE RING TIP
Sleeve
3
3
1
1
2
2
1
3
2
TIP RING SLEEVE
Sleeve
1
2
1
2
3
3
Tip
Ring
1
2
3
Sleeve
Elvis Passive Full-range Speakers
Tip
Ring
speaker cable
speaker cable
Unbalanced
1
Tip
Ring
3
2
Sleeve
TIP RING SLEEVE
Tip
1
3
2
Sleeve
1
2
3
1
2
3
Stereo
Power Amplifier
TIP SLEEVE
Tip
TIP SLEEVE
Sleeve
SLEEVE TIP
Tip
Ring
TIP RING SLEEVE
SLEEVE RINGTIP
1
2
3
3
1
1
2
2
Sleeve
3
Tip
Sleeve
Tip
Ring
Sleeve
1
2
3
Left
Main Mix
Output
Tripod
Mount
Right
Main Mix
Output
Mixer
10
3
Tripod
Mount
-. For Passive Subwoofer & Satellite Speakers
-. ACTIVE SUBWOOFER Speaker for ELVIS12 SA / ELVIS15 SA
1). Connect one side of speaker cable to the Output CHA/CHB or Binding Post of your stereo power amplifier and the other
side to the Input socket of your subwoofer, with the second speaker cable connect the Output of the subwoofer to the
Input of satellite.
(1) Bi-polar main power switch.
(2) Input AC power socket with main fuse.
(3) Ground Swicth.
2). Complete other connections as illustrated.
(4) POWER, blue LED, indicate ON status.
3). Turn on your mixer first, then the stereo power amplifier.
(5) SIGN / COMP, signal/compressor, green/red LED
4). Turn up the volume controls of your amplifier to about 70%.
(6) LEFT signal output on XLR or Jack connector for active satellite, under electronic crossover at 125Hz.
5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the output
level.
(7) RIGHT on XLR connector for active satellite, under electronic crossover at 125Hz.
(8) VOLUME main power amplifier control.
(9) RIGHT, input signal on XLR connector.
6). After using, turn off your stereo power amplifier first, then the mixer.
(10) LEFT/MONO, input signal on COMBO connector.
QUICK START
ELVIS Passive Subwoofer & Satellite Speakers
LINK
(6)
LEFT/
MONO
Speaker Cable
Speaker Cable
OUT
pole
Mount
pole
Mount
RIGHT
(7)
VOLUME
Speaker Cable
(8)
Speaker Cable
-
+4dBu
1
3
TIDE
(10)
2
NEW
PUSH
LEFT/
MONO
IN
Stereo
Power Amplifier
1
TIDE
3
(9)
2
SERIAL
NEW
MODEL
PUSH
RIGHT
GND
(3)
AC INPUT: 230V~ 50Hz
Right
Main Mix
Output
Left
Main Mix
Output
ON
POWER
OFF
Use only with a 250V fuse
Mixer
(2)
4
SIGN
COMP
(1)
9
(5)
(4)
2. QUICK START - ACTIVE SPEAKER CABINET
-. ACTIVE FULL- RANGE Speaker for ELVIS10A / ELVIS12A / ELVIS15A / ELVIS12MA
(1) Bi-polar main power switch.
Make all initial connections with all the equipment powered off, and ensure that all the main volume controls are turned completely
down.
(2) Input AC power socket with main fuse.
(3) Ground Swicth.
-. For Active Full-range Speakers
(4) POWER, blue LED, indicate ON status.
1). Connect one side of the signal cable at your audio mixer in to Output Left /Right (with Stereo-Jack or XLR) and
the other side of the cable in to the Line Input (COMBO) of your active speaker cabinet (with Stereo-Jack or XLR).
(5) SIGN / COMP, signal/compressor, green/red LED
(6) LINE OUT at + 4dB on XLR connector
2). Connect the power cord to mains.
(7) LINE IN at + 4dB on COMBO connector.
3). Turn on your mixer first, then the active speaker cabinets.
(8) VOLUME main power amplifier control.
(9) LOW / MID / HIGH, EQ tone control at +/- 6dB.
4). Turn up the volume control fo the active speaker cabinets.
(10) GAIN control for microphone -10/ - 45dB.
5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the
output level.
(11) MIC IN on balanced XLR, for microphone.
6). After using, turn off your active speaker cabinets first, then the mixer.
3
TIDE
1
Elvis Active Full-range Speakers
(11)
2
NEW
MIC IN
PUSH
QUICK START
(10)
MIC GAIN
-10dB
-45dB
-6dB
+6dB
Signal Cable
Signal Cable
HIGH
(9)
MIDDLE
-6dB
+6dB
Power Cord
LOW
-6dB
+6dB
(8)
VOLUME
+4dBu
1
Tripod
Mount
2
3
TIDE
NEW
PUSH
-
LINE-IN
Power Cord
Right
Main Mix
Output
Left
Main Mix
Output
(7)
Tripod
Mount
MODEL
SERIAL
(6)
LINE-OUT
Mixer
AC INPUT: 230V~ 50Hz
GND
(3)
ON
SIGN
COMP
OFF
Use only with a 250V fuse
(2)
POWER
(5)
(4)
(1)
8
5
3. CONNECTION PLATE
-. For Active Subwoofer & Satellite Speakers
1). Connect one side of signal cable at your audio mixer in to Output Left /Right (with Stereo-Jack or XLR) and the other
side of the cable in to the Left / Mono Input (COMBO) of the active subwoofer; with the second signal cable connect
the Left Output of the subwoofer (Stereo/Mono-Jack or XLR) to the Line Input (COMBO) of the active satellite (with
Stereo - Jack or XLR).
- PASSIVE FULL-RANGE Speaker for ELVIS10 / ELVIS12 / ELVIS15 / ELVIS12M
(1) INPUT: Receive the power coming from an external power amplifier (SPK +1/-1 connected; +2/-2 not connected).
(2) THRU: Direct LINK for connect in parallel a second speaker cabinet (SPK +1/-1 connected; +2/-2 not connected).
2). Connect the power cord to mains.
3). Turn on your mixer first, then the active speaker cabinets.
4). Turn up the volume control fo the active speaker cabinets.
R
LTO
5). Use PFL function to get the proper input level for the mixer, and adjust the Main Mix Level control to manipulate the
output level.
ELVIS 12
SOUND REINFORCEMENT SPEAKER SYSTEM
Power Handling:
AES - 180 Watts
PEAK - 360 Watts
6). After using, turn off your active speaker cabinets first, then the mixer.
IMPEDANCE:
8 ohms nominal
MODEL
QUICK START
SERIAL
DESIGNED AND DEVELOPMENT IN ITALY
Elvis Active Subwoofer & Satellite Speakers
INPUT
THRU
LINK
(2)
(1)
Signal Cable
- PASSIVE SUBWOOFER Speaker for ELVIS12S / ELVIS15S
Power Cord
(1) INPUT: Riceive the power coming from an external amplifier (SPK +1/-1 connected;+2/-2 not connected).
Tripod
Mount
Tripod
Mount
(2) OUTPUT: Power output for satellite speaker, under passive crossover filtered at 125Hz (SPK +1/-1 connected;
+2/-2 not connected).
Signal Cable
R
LTO
ELVIS 12S
Left
Main Mix
Output
Right
Main Mix
Output
POWER HANDLING:
AES - 200 Watts
PEAK - 400 Watts
IMPEDANCE:
4 ohms nominal
MODEL
SERIAL
DESIGNED AND DEVELOPMENT IN ITALY
6
INPUT
OUTPUT
(1)
(2)
7