Download quick installation guide

EWS 2 door access control unit
Quick Installa on Guide (for EWS ver.3.5)
Complete user manual and so ware supplied on the CD-R provided or on www.visual-plus.com
(press and hold for 3sec to reset the IP,
the port and the network password)
(CR2032)
470NF
Electric Door Strike
(AC powered)
Reset IP
Battery
C
R 10K
AC
Default IP:192.168.1.100; port:4001
pink
violet
R2
C28
R1
1N4007
NO3 COM3NC3 NO4 COM4NC4
1N4007
NO3 COM NC3 NO4 COM NC4
NO1 COM1NC1 NO2 COM2NC2
Earth
screw
C31
DT1
gnd12V
+
NO1 COM NC1 NO2 COM NC2
RE4
RE1
Door 1
RE2
Door 2
RE3
Free Out 1 Free Out 2
A
A
A
LD9
LD8 R35
LD6 R33
Earth
C30
D0 D1
led1 led2 GND+12V D0 D1
FUSE3
Fuse
Electric Door Strike
(DC powered)
J1
L1
L7
led1 led2 gnd 12V
A
L2
D13
IC7
ICN2
C19
D0 D1
ZD2
D3
C27
LD5 R32
IC3
C1
R16
C6
C18
led1 led2 GND+12V D0 D1
black
red
white
yellow
R25
RS485
led1 led2 gnd 12V
A
LD13
C29
L6
ZD1
R1
R13
R2
D1
D0
12V out
GND
IC8
FUSE1
LD15
max. 50 m.
C32
green
orange
black
red
white
yellow
R34 R38
IC5
R53
R15
R24R49
18
R
22
R
D2
C16
L5
A
L8
ZD4
R3
R14
R4
ZD3
L9
R36
RX3
RX4
C12
Free Led 2
LD20
D5
C43
U5
R48
D10
C45
R21
C13
R19
A B
B
3.3V
ICN1
C44
R20
R45
EWS PCB ver. 3.5
R11
R37
Free
R47 Led 1A
C17
Rb6
L4
C2
U4
5V
TAMPER
LD12
C15
X1
D1
D0
12V out
GND
TCP/IP
A
EWS v3.2
A
LD11
IC1
C33 Free R55
Led A2 LD16
R9
LD14
Free R46
Led 1
Sensors
ZD6
IC6
Door Sensor2
ZD5
A
GND
R10
Door Sensor1
L11
L10
C34
C3
Exit Button2 L3
A
R17
R30
X3
GND
A
1K
C5
12V
C41
C42
IC11
Exit Button1
U1
LD21
(NC, mechanical or
relay dry contact)
R50
R54
P. Button
PB1 gnd PB2 DS1 gnd DS2
Door Sensor
LD24
System
OK
BAT
12Vdc Out
R7
Free In 1 IC15
+
IC12
Free In 1 IC2 In 2 +
Free
Free In 2TAS1
R6
A
LD23
IC1
FUSE2
+ 12V OUT
Free Inputs
1K
A
A
Busy
Tx
Rx
R62
LD22
A
LD18
LD19
R5
R23
+
A
R28
12V out
But1 GNDBut2 Sen1 GNDSen2
(NO, mechanical or
relay dry contact)
+
F 12V Fin1+ Fin1- Fin2+ Fin2-
Exit Button
Dry
contact
LD17
C4
IN1 IN2 IN2
12V IN1
+ - + -
Contact with
external tension
+
5 - 30V
-
A
-
DC
Electro Magnetic
Lock
+
-
GND+12V
max. 50 m.
C40
H1
+ Power
Supply
- +
Jumper
RS485 termination
Power
Supply
BIOC
MINI-M
Specifica ons:
Power Supply:
User Capacity:
Event capacity:
Communica on:
Controllers per system:
Door relays:
Programmable Outputs:
Readers:
Programmable Inputs:
Door sensors:
Exit Bu on Inputs:
Wiegand interface:
Entry Mode:
Environment temperature:
Humidity:
Tamper:
Consump on:
11-15VDC
max. 15000
max. 30000
TCP/IP or RS485
unlimited
2 (250 VAC, 10A)
2 (250 VAC, 10A)
2
2 (5-30VDC, 3-28mA)
2
2
26bit, 34bit or customizable (8 to 128bit)
Card, PIN, Finger, Card or/and PIN, Card or/and Finger, PIN or/and Finger, Finger on Card
0 - 45⁰C
0-80 %, non condensing
Yes
300 mA (without readers)
Installa on:
1. Insert the ba ery provided with the hardware kit.
2. Connect the devices according to the connec on diagram above.
3. Use the provided 1K resistors for the Door Sensors and Push Bu ons.
4. Use the diodes provided when the door lock is DC powered or the capacitor+10K resistor when the lock is AC powered.
5. Use the provided resistors for RS485 tuning.
EWS quick guide 1.0
Instruc ons:
1. Keep the distance reader to controller less than 50 meters.
2. Always use twisted pair cables when wiring a RS485 network (biometric readers or EWS controllers).
3. Do not use twisted pair cables for the Wiegand wires (D0 and D1).
4. Always keep the RS485 line in daisy chain.
5. Make sure that the terminal block is correctly inserted, make sure that is not shi ed le /right by one posi on and see if
the wires are not put in reverse order.
6. Do not swap the RS485 terminal with the power supply terminal.
7. All the controllers that are communica ng via TCP/IP must have different IP address.
Communica on:
Mixed
TCP/IP
PROS Software
Switch, Router
TCP/IP max. 90m.
RS 485 1 km max / 32 Units (EWS and Biometric Readers)
PROS Software
TCP/IP max. 90m.
Switch, Router
RS 485 1 km max / 32 Units (EWS and Biometric Readers)
PROS Software
Serial (RS485)
USB
TCP/IP max. 90m.
RS 485 1 km max / 32 Units (EWS and Biometric Readers)
RS 485
RS 485
RS485 - USB Converter
RS485 tuning:
Put the jumper (120ohm) in closed position on
the first and the last controller on a RS485 network
PC
Jumper for
RS485 termination
TCP/IP
gnd
gnd
RS485
50 ohm
1 km max / 32 Units (EWS and Biometric Readers)
50 ohm
IMPORTANT NOTE:
- The RS485 Communication Line must be made in daisy chain, NOT in a star type configuration.
- The cable must be twisted and shielded. If the shield is used, connect the EARTH from ONE side of the RS 485 Line to
the shield cable.
- Connect the ground of each unit in the RS 485 Line using a third wire in the same cable.
RS485 Termina on resistors:
- Terminate both ends of the line with 120 Ohm resistor. If end of line is EWS, use built in resistor (120 ohm) by closing
the jumper.
- If the communica on is not established and stable, use the external resistors provided in the hardware kit.
When using CAT 5 compa ble cable, in most of the cases, termina on made with 50 Ohm external resistor or combina on
of 50 Ohm external and termina on resistor from the EWS (120 Ohm) should be the solu on.
EWS quick guide 1.0