Download User Manual - Music Direct

ENGLISH
Problem
Cause
fails
•The amplifier power is not
ON.
•The amplifier’s
control is set
minimum level.
volume
at the
•Place the disc in the disc
tray correctly.
3
•Clean the disc’s surface.
4
•The disc may be unable to
be played if it has a lot of
scratches.
•The disc may be unable
to be played if it is badly
warped.
•Connect
the
cables
correctly.
(See
the
instruction
manual for the amplifier.)
•Turn ON the power to the
amplifier.
(See
the
instruction
manual for the amplifier.)
•Switch the amplifier’s
function or selector switch
to “CD” or “AUX” or such
(to whatever you have
connected this unit to).
(See
the
instruction
manual for the amplifier.)
•Adjust
the
amplifier
volume.
(See
the
instruction
manual for the amplifier.)
–
12
3
–
8 ,9
–
–
4
4
4
11
7
3
3 ,16
12
20
Index
•The amplifier’s function or
selector switch is not set
to “CD” or “AUX” or such
(to whatever you have
connected this unit to).
11
4
Specifications
The disc is rotating •The amplifier and speakers
but no sound is heard. are not connected correctly.
Page
control •This unit is too far away •Move closer to this
not from the remote control.
unit, and operate the
remote control within the
operating range.
•There is an obstacle •Remove the obstacle.
between this unit and the
remote control.
•The
remote
control’s •Replace all batteries with
batteries are dead.
new ones.
•A strong light is hitting the •Do not let strong light hit
unit’s sensor window.
the sensor window.
•The switch on the back of •When using this unit
the REMOTE CONTROL is independently, set the
on EXT.
switch to INT.
•This unit is in the amplifier •Press the MODE CD
operation mode.
button to switch the
operation mode.
CD-R/CD-RW
disc •The disc is placed in upside •Place the disc in the tray
cannot be played.
down.
correctly.
•The information recorded •Record correct information
is not in an audio (CD- that is compatible with to
DA) format. Or the MP3/ this unit.
WMA file was not properly
recorded.
Cannot switch the •Start Sound Mode is set to •Change Start Sound Mode
sound mode of an CD.
setting to Super Audio CD.
SA-CD hybrid layer
disc.
Sound is too quiet •The PC volume is turned •Turn the PC volume up.
when signals are down.
output from a PC.
No sound comes out •The headphone output is •Press the PHONES button
of the headphone.
disabled.
to enable the headphone
output.
is
Page
Troubleshooting
•The disc is warped.
Corrective action
•Insert the power cord plug
into the socket.
•Turn the power to this unit
ON.
•Place the disc in the disc
tray correctly.
Corrective action
Explanation of terms
to •The power cord is pulled
out of the socket.
•Power to this unit is not
ON.
•The disc is not placed in the
correct position on the disc
tray.
•The disc is placed in upside
down. (The disc is placed in
with the label facing down).
The disc stops rotating •The disc is dirty.
in mid-operation.
•The disc is scratched.
Remote
operation
possible.
Cause
Operation
The disc
rotate.
Problem
Basic connections
If a problem occurs, first check the following:
1. Are the connections correct?
2. Is the unit being operated as described in the owner’s manual?
If this unit does not operate properly, check the items listed in the table below. If the problem
persist there may be a malfunction.
In this case, disconnect the power immediately and contact the retail outlet.
Getting started
Troubleshooting
14
–
26
1.SA-11S3U_ENG_0525.indd
26
2012/05/25
20:09:09
ENGLISH
[USB/iPod]
Problem
Cause
“USB OC” appears •The voltage able to be
on the display.
supplied from this unit via
the USB memory device
has been exceeded.
“Empty” appears on
the display.
The sound of the USB
memory device being
connected is not
heard.
Corrective action
•The USB memory device
is not supported. Please
use a USB memory
device with an operating
current that is less than
1 A.
•To clear the “USB OC”,
remove the USB memory
device and turn this unit
off and on.
•No file able to be played on •Check supported formats.
this unit exists.
•The amplifier and speakers •Connect the cables
are not connected properly. correctly. (See the
instruction manual for the
amplifier.)
•The amplifier power is not •Turn the amplifier power
ON.
ON. (See the instruction
manual for the amplifier.)
•The amplifier’s function
•Switch the amplifier’s
or selector switch is not
function or selector
set to “CD” or “AUX” or
switch to “CD” or “AUX”
such (to whatever you have or such (to whatever you
connected this unit to).
have connected this unit
to). (See the instruction
manual for the amplifier.)
•Adjust the amplifier
•The amplifier’s volume
volume. (See the
control is set at the
instruction manual for the
minimum level.
amplifier.)
Page
–
–
18
–
–
–
–
Problem
Cause
Corrective action
The sound of the iPod •The amplifier and speakers •Connect the cables
being connected is are not connected
correctly. (See the
not heard.
correctly.
instruction manual for the
amplifier.)
•The amplifier power is not •Turn ON the power to
ON.
the amplifier. (See the
instruction manual for the
amplifier.)
•The amplifier’s function
•Switch the amplifier’s
or selector switch is not
function or selector
set to “CD” or “AUX” or
switch to “CD” or “AUX”
such (to whatever you have or such (to whatever you
connected this unit to).
have connected this unit
to). (See the instruction
manual for the amplifier.)
•The amplifier’s volume
•Adjust the amplifier
control is set at the
volume. (See the
minimum level.
instruction manual for the
amplifier.)
•Wait until reading is
Reading
of
USB •When connecting a highcompleted.
memory device takes capacity USB memory
time.
device, it will take time
to read depending on its
capacity. Several minutes
may be required for reading
when using a high-capacity
device.
Power fails to switch •The unit’s power switch
•Press the unit’s power
on when the remote is off.
operation switch.
•Or, press the unit’s
controller’s X CD is
power operation switch,
pressed.
then press the remote
controller’s X CD.
Page
10
–
–
–
–
12
12
27
1.SA-11S3U_ENG_0525.indd
27
2012/05/25
20:09:09
ENGLISH
nnAudio performance
Crystal accuracy
2.3 V RMS stereo
35 mW / 32 Ω
(variable maximum)
2.3 V RMS stereo
35 mW / 32 Ω
(variable maximum)
—
—
0.5 Vp-p (75 Ω)
-19 dBm
AlGaAs
780 nm
16-bit Linear PCM
44.1 kHz
Troubleshooting
AlGaAs
650 nm
1-bit DSD
2.8224 MHz
2 channels
2 Hz – 20 kHz
2 Hz – 20 kHz
110 dB
100 dB
0.0015 % (1 kHz)
Explanation of terms
• Digital output
output level (cinch JACK):
output level (optical):
• Optical Readout System
Laser:
Wave length:
Signal type:
Sampling frequency:
2 channels
2 Hz – 100 kHz
2 Hz – 50 kHz (–3 dB)
109 dB (Audible range)
109 dB (Audible range)
0.0009 %
(1 kHz, Audible range)
Crystal accuracy
Operation
Wow & flutter:
• Output level
Unbalanced:
Headphone output:
GCDH
Basic connections
• Analog output
Channels:
Playable frequency range:
Playable frequency response:
S/N:
Dynamic range:
Harmonic distortion:
GSuper Audio CDH
Getting started
Specifications
nnGeneral
AC 120 V, 60 Hz
45 W
Standby: 0.3 W or less
Operating temperatures:
+5 ˚C – +35 ˚C
Operating humidity:
5 – 90 % (without dew)
zz For purposes of improvement, specifications and design are subject to change without
notice.
Power supply:
Power consumption:
Specifications
Index
28
1.SA-11S3U_ENG_0525.indd
28
2012/05/25
20:09:09
Dimensions / Dimensions / Dimensions
16 27/64 (417.0)
15 3/4 (400.0)
13/32
(10.5)
Unit / Unité / Unidad : inch (mm)
2 23/32
(69.0)
11 57/64 (302.0)
2 41/64
(67.0)
2 23/32
(69.0)
5 (127.0)
45/64 (18.0)
4 19/64 (109.0)
17 21/64 (440.0)
Weight / Poids / Peso : 36 lbs 6.02 oz (16.5 kg)
10.SA-11S3 U_BackPage_0525.indd
4
2012/05/25
20:02:46