Download Manual - Performance Audio

Galaxian Gem LED General Introduction
Unpacking: Thank you for purchasing the Galaxian Gem LED by
American DJ®. Every Galaxian Gem LED has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all equipment necessary to operate
the unit has arrived intact. In the event damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Please do not return this unit to your dealer without contacting customer support first.
Introduction: The Galaxian Gem LED is a 2-FX-in-1 lighting effect
with dual RGBW LED moonflowers, plus a “Galaxian style” effect with
100’s of green beams all in one fixture. The Galaxian Gem LED has
three operating modes; sound active mode, show mode, or DMX controlled. The Galaxian Gem LED can operate as a stand alone fixture
or in a Master/Slave configuration. For best results use fog or special
effects smoke to enhance the beams projections.
Customer Support: American DJ® provides a toll free customer
support line, to provide set up help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.americandj.com for any comments or suggestions. For service related issue please contact American DJ®. Service Hours are Monday through Friday 8:00 a.m. to 4:30
p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: [email protected]
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
User Instructions
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ customer support.
PLEASE recycle the shipping carton whenever possible.
1/12
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 2
Galaxian Gem LED General Instructions
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future
reference.
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
Galaxian Gem LED •
•
•
•
•
•
•
Features
30mW Green Laser Diode
5 Channel DMX Control
3 Operating Modes - Sound Active, Show Mode, & DMX Control
Stand Alone or Master-Slave Configuration
Digital Display for Address and Function Setting
UC3 Controller (Not Included)
Power Cord Daisy Chaining
Galaxian Gem LED
Warranty Registration
The Galaxian Gem LED carries a 90 day limited warranty. Please
fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight
pre-paid and accompany a return authorization (R.A.) number. If the
unit is under warranty you must provide a copy of your proof of purchase invoice. Please contact American DJ® customer support for a
R.A. number.
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 3
Galaxian Gem LED !
Safety Precautions
DANGER
VISIBLE LASER RADIATION
-AVOID DIRECT EYE EXPOSURE
LASER DIODE
WAVELENGTH : 635~650 nm
Max Output : <4.9mW
Class IIIa Laser Product
!
Safety Issues: This unit may “pop” the fuse if the maximum allotted
load of 2 amps is reached.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture.
•Do not spill water or other liquids into or on to your unit.
•Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. Do not attempt to operate this unit if the power cord has been frayed or broken.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product outdoors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power cords should be routed so they are not likely to be walked on, pinched by items placed upon or against them.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 19 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a
marked change in performance.
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 4
Galaxian Gem LED
Laser Warnings and Safety
NON-INTERLOCKED HOUSING WARNING
The Galaxian 3D contains high power laser devices internally. Do not
open the laser housing, due to the potential exposure to unsafe levels
of laser radiation. The laser power levels, if the unit is opened, can
cause instant blindness, skin burns and fires.
STOP AND READ ALL LASER SAFETY DATA
OPERATION INSTRUCTIONS AND LASER SAFETY
Galaxian Gem LED
Laser Warnings and Safety
After setting up, and before public use, test laser to ensure proper
function. Do not use if any defect is detected. Do not use if laser
emits only one or two laser beams rather than dozens/hundreds, as
this could indicate damage to the diffraction grating optic, and could
allow emission of higher laser levels above Class 3R.
Do not point lasers at people or animals. Never look into the laser
aperture or laser beams.
The light source emitted from this product can potentially cause eye
injury if not set up and used properly. The light source emitted from a
laser is very different from any other light sources with which you may
be aware of. Laser light is thousands of times more concentrated
than any light from any other kind of light source. This concentration
of light can cause instant eye injuries, primarily by burning the retina
(the back of your eyeball contatining cells that are sensitive to light).
Even if you cannot feel “heat” from a laser beam, it can still potentially injure or blind you or your audience. Even very small amounts
of laser beam light are potentially hazardous even at long distances.
Laser eye injuries can be sustained faster than you can blink.
Do not point lasers in areas in which people can potentially get
exposed, such as uncontrolled balconies, etc.
Do not think that because this laser splits the laser beam into hundreds of beams and that the laser beam is scanned out in high
speed, that an individual laser beam is safe for eye exposure. This
laser uses dozens of milliwatts of laser power (Class 3B levels internally) before it splits into multiple beams (Class 3R levels). Many of
the individual beams are potentially hazardous to the eyes.
Do not use the laser if the housing is damaged, the housing is open,
or if the optics appear damaged in any way.
Do not that because the laser light is moving, it is safe. This is not
true. Nor, do the laser beams always move. Since eye injuries can
occur instantly, it is critical to prevent even the smallest possibility of
any direct eye exposure. In the laser safety regulation, it is not legal
to aim Class 3R lasers in areas which people can get exposed. This
is true even if it is aimed below people’s faces, such as on a dance
floor.
Do not operate the laser without first reading and understanding
all safety and technical data in this manual.
Always set up and install all laser effects so that all laser light is at
least 3 meters (9.8 feet) above the floor on which people can stand.
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 5
Do not point lasers at highly reflective surfaces, such as windows,
mirrors and shiny metal. Even laser reflections can be hazardous.
Never point a laser at aircraft, this is a federal offense.
Never point un-terminated laser beams into the sky.
Do not expose the output optic (aperture) to cleaning chemicals.
Do not use laser if the laser appears to be emitting only one or two
beams.
Never open the laser housing. The high laser power levels inside of
the protective housing can start fires, burn skin and will cause instant
eye injury.
Never leave this device running unattended.
The operation of a class 3R laser show is only allowed if the show
is controlled by a skilled and well- trained operator, familiar with the
data included in this manual.
The legal requirements for using laser entertainment products vary
from country to country. The user is responsible for the legal requirements at the location/country of use.
Always use proper lighting safety cables when hanging lights and
effects overhead.
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 6
Galaxian Gem LED Laser Warning Labels
Galaxian Gem LED Set Up
Power Supply: The American DJ® Galaxian Gem LED contains a
LASER RADIATION
IS EMITTED FROM
THIS APERTURE
20mm
automatic voltage switch, which will auto sense the voltage when it
is plugged into the power source. With this switch there is no need
to worry about the correct power voltage, this unit can be plugged in
anywhere.
AVOID EXPOSURE
40mm
LASER RADIATION AVOID
DIRECT EYE EXPOSURE
Maximum output <5 mW
Wavelength: 532nm
Class IIIa laser product
30 mm
41 mm
This device complies with 21 CFR chapter I,
Subchapter J, or CFR 1040.10 and 1040.11
LASER RADIATION
IS EMITTED FROM
THIS APERTURE
AVOID EXPOSURE
American DJ Supply,Inc.
6122 S.Eastern Ave.
Los Angeles. CA 90040 USA
Manufactured:
CAUTI ON - CLASS 3R
LASER RADIATION WHEN OPEN
AVOID DIRECT EYE EXPOSURE
40mm
17mm
American DJ Supply,Inc.
6122 S.Eastern Ave.
Los Angeles. CA 90040 USA
Manufactured:
LASER RADIATION AVOID
DIRECT EYE EXPOSURE
Maximum output <5 mW
Wavelength: 532nm
Class IIIa laser product
This device complies with 21 CFR chapter I,
Subchapter J, or CFR 1040.10 and 1040.11
SPEC LABEL
SPEC LABEL
12mm
40mm
©American
CAUTI ON - CLASS 3R
LASER RADIATION WHEN OPEN
AVOID DIRECT EYE EXPOSURE
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 7
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. Therefore, the first fixture controlled by the
controller could be the last fixture in the chain. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA
assigned to address 1 to that unit, no matter where it is located in the
DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Galaxian Gem LED can be controlled via DMX-512
protocol. The Galaxian Gem LED is a five channel
DMX unit. The DMX address is set electronically
using the controls on the rear panel of the unit. Your
unit and your DMX controller require a approved
DMX-512 110 Ohm Data cable for data input and
data output (Figure 1). We recommend Accu-Cable
DMX cables. If you are making your own cables, be
sure to use standard 110-120 Ohm shielded cable
Figure 1
(This cable may be purchased at almost all professional sound and lighting stores). Your cables should be made with
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 8
REMOTE
CONTROL
INPUT
SOUND
INPUT
OUTPUT
REMOTE
CONTROL
INPUT
SOUND
INPUT
Galaxian Gem LED OUTPUT
Set Up
a male and female XLR connector on either end of the cable. Also
remember that DMX cable must be daisy chained and cannot be split.
POWER
POWER
Notice: Be sure to follow
figures two and three when making your own
DMX512
DMX+,DMX-,COMMON
cables. Do not use
the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
1
2
DMX +
3
DMX -
3
1
DMX512 IN
3-PIN XLR
2
3
1
2
Figure 2
XLR Female Socket
XLR Male Socket
1 Ground
SOUND
2 Cold
2 Cold
REMOTE
CONTROL
INPUT
INPUT
OUTPUT
1 Ground
3 Hot
OUTPUT
Galaxian Gem LED Pin 1 = Ground
INPUT
Set Up
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
POWER
3-Pin XLR to 5-Pin XLR Conversion
Termination reduces signal errors and
avoids signal transmissionGround/Shield
problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
DataPIN
Compliment
(- signal)
120 Ohm 1/4 W) between
2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Data True (+ signal)
XLR Pin Configuration
REMOTE
CONTROL
INPUT
SOUND
INPUT
Conductor
COMMON
DMX512 OUT
3-PIN XLR
REMOTE
CONTROL
INPUT
SOUND
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Pin 1
Pin 1
Pin 2
Pin 2
Pin 3
Pin 3
Not Used
Pin 4 - Do Not Use
Not Used
Pin 5 - Do Not Use
OUTPUT
Pin 2 = Data Compliment (negative)
3 Hot
Pin 3 = Data True (positive)
Figure 3
Special Note: Line Termination. When longer runs of cable are
POWER
POWER
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
3
1
2
DMX512 IN
3-PIN XLR
©American
3
1
2
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 9
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 10
Galaxian Gem LED
System Menu Chart
Galaxian Gem LED
System Menu
System Menu: When making adjustments press ENTER
to confirm your setup and then press and hold the MENU
button for at least 3 seconds. To exit without making any
adjustments press the MENU button.
ADDR - DMX Address Setting.
1. Press the MENU, UP, or DOWN buttons until “ADDR” is displayed,
press ENTER.
2. The current address will now be displayed and flashing. Press the
UP or DOWN buttons to find your desired address. When you have
found your desired address press ENTER.
SLND - This will let you set unit as a master or slave in a
master/slave configuration.
1. Press the MENU button until “SLND” is displayed, press ENTER.
“MSTR”, “SL 1” or “SL 2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim and exit.
NOTE: In a Master/Slave configuration you can make one fixture the
Master and then set the next fixture to “SL 2”, the fixtures will now
have contrast movement to each other.
SHND: SH 0 - SH8 - Show modes 0-8 (Factory programs).
Show mode can run with or without sound active mode.
1. Press the MENU button until “SHND” is displayed, press ENTER.
2. “Sh X” will now be displayed, “X” representing a number between
0-8. Programs 1-8 are factory programs, while “Sh 0” is random mode.
Press the UP or DOWN buttons to find your desired show.
3. When you have found your desired show press ENTER, then press
and hold the MENU button for at least 3 seconds to activate.
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 11
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 12
Galaxian Gem LED
System Menu
SOUN - Sound Active mode.
1. Press the MENU button until “SOUN” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or DOWN
buttons to select “ON” to activate sound active mode, or “OFF” to
deactivate sound active mode.
3. Press ENTER to confirm, then press and hold the MENU button for
at least 3 seconds to activate.
SENS - Sound sensitivity control.
1. Press the MENU button until “SENS” is displayed, press ENTER.
2. The display will show a number between 0-100. Press the UP or
DOWN buttons to adjust the sound sensitivity. 0 being the least sensitive and 100 the most sensitive.
3. Press the ENTER button to confirm.
BLND - Blackout or Stand by mode.
1. Press the MENU button until “BLND” is displayed, press ENTER.
Either Yes or No will be displayed.
2. To activate Blackout tap the UP or DOWN buttons until “Yes” is
displayed, press ENTER to confim. The fixture will now be in Blackout
mode. To deactivate Blackout mode, select “No” and press Enter.
Galaxian Gem LED
System Menu
DISP - This function will reverse the display 180º.
1. Press the MENU button until “DISP” is displayed, press ENTER.
2. Press the UP button to select “DSIP” to activate this function, or
“DISP” to deactivate this function.
3. Press ENTER to confirm.
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is displayed, press ENTER.
2. The fixture will now run a self test.
FHRS - With this function you can display the running time
of the fixture.
1. Press the MENU button until “FHRS” is displayed, press ENTER.
2. The display shows the running time of the unit. Press MENU to
exit.
VER - With this function you can display the version software of the unit.
1. Press the MENU button until “VER” is displayed, press ENTER.
2. The display will now display the version of software. Press MENU
to exit.
LED - With this function you can have the LED display
turn off after 10 seconds.
1. Press the MENU button until “LED” is displayed, press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or DOWN
buttons to select “ON” to keep the LED display on at all times, or
“OFF” to switch to have the LED display switch off after 10 seconds.
3. Press ENTER to confirm.
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 13
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 14
Galaxian Gem LED
Operation
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
Operating Modes: The Galaxian Gem LED can operate in three
different modes. In each mode you can run the fixture as a
stand alone fixture or in a master/slave confiugration.
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Galaxian Gem LED is a five channel DMX fixture. See page 17 for detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 8-10 as well as the set-up specifications that are included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instruction on page 12 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
Show Mode: In this mode you can choose 1 of 8 show modes to run.
This operating mode can be used in stand alone unit or in a masterslave configuration.
1. Tap the MENU button until “SHND” is displayed, and press ENTER.
2. Tap the UP or DOWN buttons until you find your desired show, and press ENTER then press and hold MENU for 3 seconds to confirm. See page 12 for more info.
3. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout. See page 17 for UC3 controls.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 15
Galaxian Gem LED
Operation
1. Tap the MENU button until “SOUN” is displayed, and press ENTER.
2. Tap the UP or DOWN buttons to choose either OFF or ON, and press ENTER, then press and hold MENU for 3 seconds to con-
firm. To adjust the sound sensitivity see page 13.
3. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout. See page 17 for UC3 controls.
Master-Slave Operation This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth- er via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. For the Master unit press the MENU button until “SLND” is dis-
played, and Press ENTER. Set the unit to “MAST” and press ENTER.
3. Next set the Master to your desired operating mode.
4. For the slave units press the MENU button until “SLND” is dis-
played, and Press ENTER. Set the slave units to either “SL 1” or
“SL 2”.
5. The slave units will now follow the Master unit.
6. The optional UC3 Controller (not included) may be used to con-
trol different functions including blackout. See page 17 for UC3 controls.
Galaxian Gem LED
Power Cord Daisy Chain
With this feature you can connect the fixtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 16 fixtures maximum. After 16 fixtures you will need
to use a new power outlet. They must be the same fixtures. DO
NOT mix fixtures.
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 16
Galaxian Gem LED
UC3 Control
Galaxian Gem LED
Fuse Replacement
Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.
Galaxian Gem LED
Channel
1
2
3
4
5
©American
Value
0-7
8 - 15
16 - 239
240 - 247
248 - 255
0-9
10 - 120
121 - 134
135 - 245
246 - 255
0-7
8 - 37
38 - 67
68 - 97
98 - 127
128 - 157
158 - 187
188 - 217
218 - 247
248 - 255
0 - 255
0-7
8 - 247
248 - 255
DMX Values & Traits
Function
LASER ON/OFF
LASER OFF
LASER ON
LASER STROBING SLOW - FAST
LASER SOUND ACTIVE
LASER ON
LASER ROTATION
NO ROTATION
CLOCKWISE FAST - SLOW
NO ROTATION
COUNTER-CLOCKWISE SLOW - FAST
NO ROTATION
LED CHASES
BLACKOUT
CHASE 1
CHASE 2
CHASE 3
CHASE 4
CHASE 5
CHASE 6
CHASE 7
CHASE 8
SOUND ACTIVE
LED CHASE SPEED
SLOW - FAST
LED STROBING
NO FUNCTION
STROBING SLOW - FAST
SOUND ACTIVE STROBING
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 17
Galaxian Gem LED Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning
the internal and external lenses should be carried out periodically to
optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (I.e. smoke, fog residue, dust, dew). In heavy use we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp beam output.
Galaxian Gem LED Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1.
Be sure the external fuse has not blown. The fuse is located on the rear panel of the unit.
2.Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
©American
DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 18
Galaxian Gem LED Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B.
For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ, Inc. will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty
service and repair labor by reason of defects in material or workmanship. The sole responsibility
of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of American DJ. All products covered by this
warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
E.
American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore
manufactured. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ, Inc. in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set forth
above. And no warranties, whether expressed or implied, including warranties of merchantability
or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s
sole remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers)
• All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which
have a 1-year (365 day Limited Warranty)
©American DJ® - www.americandj.com - Galaxian Gem LED Instruction Manual Page 19
Galaxian Gem LED Specifications
Model: Galaxian Gem LED
Voltage:
100V ~ 240V/50~60Hz
LEDs:
46 x 5mm RGBW LEDs (16 Red, 10 Green, 10 Blue, & 10 White)
Lasers:
30mW Green Diode
Power Consumption:
20W
Fuse:7 Amp
Power Cord Daisy Chain: 16 Fixtures Max.
Beam Angle:
82 Degrees
Dimensions: 11.5”(L) x 13”(W) x 8”(H)
290mm x 325mm x 201mm
Weight:
9 Lbs. / 3.7 kgs.
Colors:
RGBW + Green
Duty Cycle:
None
DMX: 5 DMX Channels
Sound Active:Yes
Working Position:
Any Safe, Secure Position
Warranty: 90 Days
Auto Sensing Voltage: This fixture contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
©American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.americandj.com / E-mail: [email protected]
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
[email protected] / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99