1
Download AX-902
Transcript
BLUETOOTH ENABLED CD/MP3/WMA RECEIVER IPOD CONTROL with INTERFACE CABLE USB & FRONT PANEL AUX INPUT SPECIFICATIONS: GENERAL: Flip Down / Detachable Face Panel Includes Black and Silver Trim Frames ISO DIN Chassis &ISO Wiring Connector 12 Volt DC - Negative Ground Chassis: 178(W)x50(H)x158(D) mm PLAYER: CD/MP3/WMA -CDR/CDRW Player Auto Loading/Eject iPod Compatible Electronic Shock Protection (12/45 Sec. in CD / 120 Sec. in MP3) Intro, Repeat and Random Play MP3/WMA Files - Select Folder Track/File or Character Search BLUETOOTH: Bluetooth in Phone Mode Remote Dial Keypad External Microphone Phone Contacts TUNER: AM/FM Stereo PLL Frequency Display 30 Station Presets (18FM/12AM) Digital Clock Stereo/Mono - Local/Distant Long Range XTREME Tuner AUDIO CONTROL: Electronic Volume/Balance/ Treble/Bass and Fader Controls Audio DSP Function Subwoofer Output 4 Channel RCA Line-out RCA Line-in USB / AUX Input Speaker Impedance 4-8 Ohms 5 Volt Preamp Output High Power 40 Watts x 4 ch DESIGNED FOR AUSTRALASIAN CONDITIONS AX-902 INSTALLATION PRECAUTIONS • Carefully choose the mounting location so normal driving is not affected. • Avoid installing the unit where it would be subject to high temperatures (direct sunlight or hot air from the heater) or where it would be subject to dust, dirt or excessive vibration. • Only use the mounting hardware supplied to ensure a safe and secure installation. • Remove the front panel before installing the unit. Mounting angle adjustment Adjust the mounting angle to less than 20°. 18mm MOUNTING EXAMPLE Installation in the dashboard 11 Release screw and bracket 3 2 5mm 3 182mm 4 53mm 2 Bend these claws, if necessary Note: Keep the release keys in the safe place as you may need them in future to remove the unit. Detaching and attaching the front panel The front panel of this unit can be detached in order to prevent theft. FOLDING DOWN AND DETACHING/ATTACHING THE FRONT PANEL Before detaching the front panel, be sure to press the PWR button (1) OFF first. Then press the button (16), to fully open the front panel. Detach the panel by pulling it towards you as illustrated. not exceed 10° 1 2 Notes: • Do not exert unnecessary pressure on the front panel when attaching it. • Please use the supplied case when the front panel is removed. TO SUPPORT THE UNIT 4 3 Dashboard 4 1. UNIT 2. RELEASE CASE 3. DASH 4. HEX NUT 5. LOCK WASHER 6. PLAIN WASHER 7. CAR BODY 8. REAR SUPPORT STRAP 9. TAPPING SCREW 10.M5 X 15 HEX BOLT 6 5 8 2 10 7 1 5 9 4 6 WIRE CONNECTION L (WHITE) R (RED) ANTENNA CONNECTOR LINE OUT (FRONT) ISO CONNECTOR B LINE OUT L (WHITE) R (RED) (REAR) LINE IN SUB WOOFER A L (WHITE) R (RED) BLUETOOTH ANTENNA ISO A/B PLUG CONNECT TO POWER ANTENNA MEMORY FRONT LEFT SPEAKER REAR LEFT SPEAKER EXTERNAL MICROPHONE BLACK GROUND (–) BLUE YELLOW RED IGNITION SWITCH (B+) BACK UP GREY + + WHITE GREY/BLACK – – WHITE/BLACK + GREEN VIOLET + – GREEN/BLACK VIOLET/BLACK – FRONT RIGHT SPEAKER REAR RIGHT SPEAKER Maintenance FUSE REPLACEMENT If a fuse blows, check all power connections and replace the fuse. If the fuse blows again there may be an electronic or wiring fault. In this case, consult your nearest service centre. Warning Use the specified amperage fuse for each lead. Use of a higher amperage fuse may cause serious damage and void the warranty. MP3 FUNCTION OF CONTROLS 3 2 1 15 14 22 13 7 16 11 20 27 MP3 9 19 21 POSITION OF CONTROLS (CAR STEREO) 23 24 25 8 5 6 12 10 26 4 (1-6) MP3 1. POWER ON/OFF ( ) 3 BUTTON: 2 1 15 14 22 13 7 16 11 20 2. FUNCTION SELECT BASS/TREBLE/BALANCE/FADER/AUDIO DSP/ LOUDNESS/SUBWOOFER/ESP/CD MULTI/SCROLL/BEEP/STEREO/LOCAL/PAIRING 3. VOL UP/VOL DOWN FOR BASS/TREBLE/BALANCE/FADER/AUDIO DSP/ LOUDNESS/SUBWOOFER/ESP/CD MULTI/SCROLL/BEEP/STEREO/LOCAL/PAIRING 4. PRESET STATIONS (1,2,3,4,5,6) 5. MUTE BUTTON (MU) 6. LOCAL/DISTANT BUTTON (LOC) 7. EQUALIZER CONTROL (EQ) 8. STEREO/MONO BUTTON (ST) MP3 18 17 9. DISPLAY BUTTON (DISP) 10.MODE BUTTON (MODE) 11. BAND BUTTON (BND) 12.AUTOMATIC OR MANUAL OR25 FREQ / 9 TUNING19(FREQ 21 UP 23 24 8 DOWN 5 6 12 10 26 CD TRACK/SEARCH BUTTON 4 (1-6) 13.AUTO SEEK SEARCH TUNING (A/PS) 14.‘SCAN’ AUTOMATIC TUNING CONTROL (SCN) 15.LCD DISPLAY 16.PANEL RELEASE BUTTON ( ) 17.CD SLOT 18.CD EJECT BUTTON ( ) 19.TOP BUTTON (TOP) 20.PAUSE BUTTON (BND) 21.INTRO BUTTON (Preview all Tracks) (INT) 22.REPEAT BUTTON (A/PS) 23.RANDOM BUTTON (RDM) 24/ 25. + 10 TRACK SEARCH DOWN/UP 26.AUX IN 18 17 27.USB PORT 27 POSITION OF CONTROLS (DIAL KEYPAD) 1. 2. 3. 4. 5. 6. 7. 8. 9. POWER ON / OFF ANSWER A CALL VOLUME + END A CALL BAND SELECT MENU FUNCTION VOLUME MODE PHONE NUMBER / BUTTON 1-6: STATION PRESETS 10. STEREO / MONO 11. SCAN STATIONS 10 9 6 11 7 5 8 3 1 2 4 Switching to Telephone Mode 1. During any operating mode, press and hold “*” to activate TELEPHONE mode. Press and hold it again to return to previous mode. Making Calls Using the Remote Control Calls can be made directly from the remote control. Before making a call, make sure that the devices are properly paired and connected. 1. Press and hold “*” on remote control. Unit will switch to phone mode. button to dial out. 2. Enter the phone number via the remote control keypad and press button to make corrections when entering numbers. Press button to end call. 3. Press Scan Radio Station SCAN function scans all stored frequencies and plays each for 5 seconds. 1. In Tuner mode, press ‘* ’ to start SCAN function. Press again to end. 2. When a channel is found, press and hold a memory preset key (1-6) to store in memory. Installation of Dial Key Pad Use double sided adhesive tape (optional) to stick the remote on the dashboard or another convenient place. To Install on Steering Wheel: Note: To use the remote, detach it first from the remote holder and point directly to the head unit. CAUTION: Do not install the remote close to or in front of any SRS (airbag). GENERAL CONTROLS 1. POWER ON/OFF Press this key to switch the unit on and off. Also, this unit can be turned on by pressing any key. 2. SELECT 3. VOLUME UP/DOWN Turn the VOL knob Right or Left (3) to adjust VOL/BASS/TREB/BAL/FAD. To select other functions, continue to press the VOL knob until the desired function is shown on the display. See Figure 1. 2 1 2 3 2 4 2 5 2 6 Fig. 1 Selection of sound control functions 1. VOL Turn the VOL knob VOLVOL orVOLVOL to increase or decrease the volume levels.These buttons can also be used to adjust the BASS, TREBLE, BALANCE and FADER. AUDIO DSP CONTROLS (2) Press the SEL button for more than 2 seconds to select Digital Sound Processor mode. 2 sec. SEL 2. SEL DSP 2 sec. VOL 3. BAS 4. TRE 5. BAL 6. FAD POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF DSP LOUD SEL SEL POP LOUD --- ROCK --- ON/OFF FLAT --- DSP OFF LOUDNESS CONTROLS (2)--- CLASSIC Press the SEL button for more than 2 seconds to activate Loudness function. 2 2 sec. sec. SEL SEL 2 sec. 2SEL sec. 2SEL sec. SEL 2 2 sec. sec. SEL 2SEL sec. 2 sec. SEL SEL 2 sec. sec. 2 2SEL sec. SEL SEL 2 sec. 2 sec. 2SEL sec. 2 sec. 2SEL sec. SEL SEL SEL 2SEL sec. 2 sec. 2SEL sec. SEL SEL 2 sec. sec. 22SEL sec. SEL SEL 2SEL sec. VOL VOL DSP DSP DSP SEL SEL VOL LOUD LOUD SEL VOL VOL WOOF LOUD ON/OFF WOOF ON/OFF POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF VOL VOL VOL orVOLVOLSEL . TheESP bass and WOOF VOL WOOF SEL LOUD WOOF ON/OFF LOUD ON/OFF mode LOUD is selectedSEL by DSP SEL SUBWOOFER MODE (2) SEL LOUD DSP LOUD SEL ON/OFF SEL MULT MULT ON/OFF SEL ESP WOOF DSP LOUD SEL Press theDSP SEL button for more than toSEL activateESP the Subwoofer mode as shown below. WOOF ESP 10/40 SEL 2 seconds LOUD SEL DSP SEL treble response will boost. ESP 10/40 VOL DSP DSP DSP DSP DSP DSP DSP DSP DSP ESP MODE VOL SEL SEL SEL VOL VOL POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF LOUD LOUD LOUD SEL SEL SEL WOOF WOOF WOOF SEL SEL VOL SEL ESP WOOF ON/OFF SEL ESP VOL LOUD SEL LOUD ON/OFF WOOF SEL LOUD SEL POP --- ROCK --CLASSIC --- FLAT ---SEL DSP OFF ESP ESP WOOF SEL SEL LOUD SEL ESP WOOF SEL SEL LOUD SEL (2) MULT MULT SEL SEL MULT ESP 10/40 MULT SEL VOL SEL WOOF ON/OFF MULT ESP 10/40 MULT VOL VOL SEL SCROLL MULT ON/OFF SEL SEL SCROLL SCROLL VOL VOL SCROLL 1/2 VOL SCROLL 1/2 BEEP ON/OFF Press SEL buttonSELforBEEP more thanSEL 2 sec. WOOF to activate Electronic Shock Protection mode as 12 sec. or 45 DSP LOUD WOOF ON/OFF MULT ON/OFF SEL ESP WOOF DSP SEL LOUD SEL sec. SCROLL MULT SEL MULT SEL ESP WOOF SEL DSP SEL LOUD SEL LOUD ON/OFF SEL SEL SEL sec. 22 sec. SEL SEL 2 sec. 2 sec. SEL 2SEL sec. SEL SEL 2 sec. SEL 2 sec. 22 sec. sec. SEL SEL SEL 2 sec. 2SEL sec. SEL SEL SEL 2 sec. sec. 22SEL sec. 2 sec. SEL SEL SEL SEL SEL SEL SEL 2 sec. SEL sec. 22 sec. SEL SEL SEL VOL VOL VOL VOL DSP BEEP DSP DSP DSP BEEP DSP DSP SEL LOUD SEL VOL BEEP ON/OFF SEL SEL LOUD SEL LOUD SEL LOUD SEL VOL STEREO SEL SEL SEL SEL LOUD LOUD SEL SEL WOOF WOOF WOOF SEL SEL SEL WOOF WOOF SEL SEL VOL WOOF ON/OFF STEREO ESP ESP ESP ESP ESP SEL SEL MULT MULT MULTIDSP CD SECTION MODESEL(2) WOOF ESP SEL ESP 10/40 LOUD SEL MULT SEL WOOF SEL LOUD SEL Press theDSP SEL button for more seconds toSEL activateESP this function. BEEP ON/OFFthan 2STEREO STEREO SEL BEEP ON/OFF VOL DSP SEL VOL LOUD SEL WOOF SEL BEEP DSP SEL SEL STEREO LOUD SEL SEL LOCAL WOOF SEL DSP DSP DSP SEL SEL SEL LOUD LOUD LOUD VOL SEL SEL SEL WOOF WOOF WOOF VOL SEL SEL SEL ESP DX/LOCAL ESP ESP ESP ESP SEL MULT SEL MULT SEL SEL SEL MULT MULT MULT SEL SEL SCROLL SCROLL SEL MULT ON/OFF SCROLL SEL SEL SCROLL SCROLL VOL VOL SEL SEL SEL VOL VOL SCROLL 1/2 SCROLL 1/2 MULT ON/OFF SCROLL SCROLL SCROLL VOL VOL CD MULTI ON: multi section CD MULTI mode is SEL selected by VOLVOL SCROLL MULT SEL Read SCROLL 1/2 ESPkey. SEL WOOF SELor DSP ON/OFF LOUD SEL SCROLL MULT SEL SEL ESP WOOF SEL DX/LOCAL DSP LOUD SEL BEEP STEREO SEL ON/OFF BEEP ON/OFFSEL LOCAL BEEP STEREO SEL STEREO SEL BEEP CD. CD MULTI OFF: ReadLOUD first section only. SCROLL MULT SEL SEL ESP WOOF DSP SEL LOCAL PAIRING BEEP STEREO SEL SEL SEL SEL SEL VOL VOL VOL ESP WOOF SEL SEL LOUD ESP WOOF SEL SEL LOUD ESP WOOF SEL SEL LOUD BEEP ON/OFF VOL VOL STEREO SEL STEREO LOCALON/OFF STEREO SEL SEL DX/LOCAL LOCAL PAIRING STEREO SEL SEL SEL DSP DSP DSP BEEP BEEP BEEP BEEP SEL SEL SEL DSP SEL DSP DSP BEEP VOL VOL SEL SEL SEL LOUD LOUD LOUD STEREO SEL SEL SEL VOL WOOF SEL WOOF SEL WOOF SEL STEREO ON/OFF ESP ESP ESP SEL SEL SEL MULT MULT MULT SEL SEL SEL SCROLL SCROLL SCROLL SEL SEL SEL SEL MULT MULT MULT SEL SEL SEL SCROLL SCROLL SCROLL 2 sec. SEL 2 sec. 2SEL sec. 2SEL sec. SEL 22sec. sec. SEL SEL 2 sec. 2SEL sec. 2 sec. 2SEL sec. SEL SEL DSP DSP DSP DSP LOUD SEL SEL SEL LOUD LOUD WOOF SEL WOOF ON/OFF VOL LOUD ON/OFF VOL WOOF SEL ESP SEL VOL POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF ESP 10/40 SCROLL MODE MULT ESP thisSEL LOUD SEL Press theDSP SEL button more SEL than 2WOOF seconds to activate WOOF SEL DSP SEL LOUD SEL for WOOFmode. ON/OFF VOL VOL DSP DSP DSP DSP SEL SEL VOL SEL VOL LOUD LOUD ON/OFF SEL ESP WOOF SEL SEL POP --- ROCK --CLASSIC --- FLAT --- SEL DSP OFF ESP WOOF SEL LOUD LOUD MULT VOL VOL MULT ON/OFF SEL ESP 10/40 SEL SEL DSP DSP SEL 2 sec. 2 sec. BEEP SEL 2SEL sec. SEL 2 sec. DSP DSP SEL SEL VOL WOOF SEL LOUD ON/OFF SEL LOUD LOUD VOL BEEP ON/OFF VOL ESP SEL MULT BEEP MODE (2) ESP WOOF SEL DSP ESP 10/40 SEL SEL LOUD SEL MULT SEL ESP WOOF SEL DSP SEL LOUD SEL 22SEL sec. Press 2sec. sec. the SEL button for more than 2 seconds to activate Beep functions. SEL SEL 2SEL sec. 2 sec. 2SEL sec. SEL 2SEL sec. 2SEL sec. 2SEL sec. 2 sec. SEL SEL 2SEL sec. SEL 22SEL sec. sec. SEL 2SEL sec. 2SEL sec. 2 sec. SEL 2SEL sec. SEL SEL SEL SEL SEL 2 sec. 2SEL sec. 2SEL sec. 2 sec. 2SEL sec. SEL SEL SEL SEL 2SEL sec. 2SEL sec. 2SEL sec. SEL SEL VOL DSP DSP DSP BEEP DSP DSP BEEP DSP DSP SEL LOUD SEL LOUD VOL SEL SEL WOOF WOOF SEL VOL MULT SEL ESP WOOF ON/OFF POP --- ROCK --- CLASSIC --- FLAT --- DSP OFF ESP WOOF SEL SEL LOUD SEL ESP WOOF SEL LOUD SEL STEREO VOL SEL SEL STEREO ON/OFF SEL VOL SEL SEL SEL SEL LOUD LOUD BEEP ON/OFFVOL SEL LOUD LOUD SEL WOOF SEL LOUD ON/OFF SEL WOOF WOOF ESP SEL ESP ESP SEL SEL SEL VOL SEL MULT SEL SEL MULT MULT ESP 10/40 MULT SEL MULT MULT ESP WOOF SEL DSP SEL LOUD SEL BEEP ON: BEEP sound can be heard when any DX/LOCAL button is pressed. WOOF SEL DSP SEL LOCAL LOUD SEL STEREO BEEP SEL SEL SEL ESP MULT SEL ESP WOOF SEL DSP SEL SEL (2) LOUD STEREO/MONO ON/OFF BEEP STEREO SEL BEEP STEREO ON/OFF MULT SEL SEL Press theDSP SEL button forLOUD more SEL than 2WOOF seconds to activate function. SEL ESP WOOF SEL SELESP these DSP ESP 10/40 SEL SEL LOUD SCROLL VOL SCROLL 1/2 22sec. SCROLL 1: Unit displays song details but no text scrolling. sec. MULT SEL ESP WOOF SEL SEL LOUD SEL 2SEL sec. DSP WOOF DSP SEL LOUDsong details SEL WOOF ON/OFF SCROLL 2: Unit displays and scrolls the textSEL information to theSCROLL left. 2SEL sec. DSP DSP SEL SEL LOUD LOUD VOL SEL SEL WOOF VOL WOOF SEL VOL WOOF ON/OFF VOL VOL DSP DSP DSP BEEP BEEP BEEP BEEP DSP ESP WOOF SEL SEL LOUD LOCAL PAIRING ESP SEL SEL SEL WOOF SEL ESPSEL WOOF SEL SEL LOUD ESP WOOF SEL SEL LOUD BEEP ON/OFF VOL STEREO SEL ON/OFF VOL LOCAL STEREO SEL STEREO SEL DX/LOCAL SEL SEL SEL VOL SEL SEL STEREO LOUD SEL SEL SEL SEL MULT MULT MULT MULT VOL MULT ON/OFF SEL SCROLL SEL MULT ON/OFF SCROLL SEL SCROLL VOL SCROLL SEL MULT ON/OFF SCROLL SEL SCROLL VOL SEL SEL ESP WOOF SEL SEL LOUD SEL SEL ESP WOOF SEL SEL LOUD SEL VOL SEL ESP WOOF ON/OFF SEL LOUD (2)SEL STEREO SEL SEL STEREO VOL LOCAL SEL SEL for STEREO DX/LOCAL button more than 2 seconds to activate this function. LOCAL PAIRING STEREO SEL SEL SEL SEL VOL BEEP ON/OFF ESP WOOF SEL DSP SEL LOUD SEL ESP WOOF SEL DSP SEL LOUD SEL ESP WOOF SEL DSP LOUD SEL VOL LOCAL BEEP STEREO SEL SEL SEL DX/LOCAL LOCAL PAIRING BEEP STEREO SEL SEL SEL VOL BEEP STEREO SEL position in areas with strongSTEREO signalON/OFF will cause radio SEL SEL SEL VOL SCROLL 1/2 VOL SCROLL 1/2 VOL SCROLL 1/2 VOL SCROLL 1/2 SCROLL SEL SEL SEL VOL SCROLL SCROLL SCROLL MULT ON/OFF MULT MULT MULT SEL SEL SEL SCROLL SCROLL SCROLL SCROLL SCROLL MULT MULT MULT SEL SEL SEL SCROLL SCROLL SCROLL MULT SEL SEL ESP WOOF SEL DSP SEL LOUD SEL When FM signalSEL is weak or distorted, reception may bySEL selecting MULT MONO. SEL ESP WOOF SEL improve DSP SEL LOUD DSP DSP DSP LOCAL/DX BEEP Press the BEEP SEL BEEP BEEP SCROLL SEL SEL “Local” to stop at only strong stations. During 2 sec. manual tuning (LOC Select Distant inESP areas with SCROLL MULTsignal. SEL SEL weak WOOF position SEL DSP SEL SEL LOUD SEL appears). 2 sec. SEL SEL DSP SEL LOUD SEL WOOF ESP SEL MULT SEL SCROLL SEL ESP SEL MULT SEL SCROLL SEL PAIRING SEL BEEP SEL PAIRING MODE (2) STEREO SEL LOCAL SEL PAIRING SEL LOCAL to activate SEL SEL theBEEP SEL forSTEREO DX/LOCAL Press SEL button more than 2 seconds Pairing for Bluetooth functions. (Please refer to HOW TO PERFORM PAIRING on page 11) VOL 2 sec. SEL SEL DSP BEEP SEL SEL LOUD STEREO SEL SEL WOOF LOCAL SEL 4. PRESET STATIONS Six numbered preset button store and recall stations for each band. Storing a station: 1. 1. Select a band (if needed) 2. Select a station 3. Hold a preset button longer than one second. Preset station number appears in the display when station is saved. Recall a station: 1. Select band (if needed) 2. Press a preset button for less than one second to select stored station. 5. MUTE BUTTON Press this button to mute the sound. Press again to return to previous volume level. 6. LOCAL/DISTANT BUTTON Press Local/Distant LOC button for listening to weak stations. “LOCAL” indicator will appear on the display. Press this button again (Distant mode) for normal operation. 7. EQUALIZER CONTROL Press EQ to select between Off/Pop/Rock/Classic/Flat equalizer modes. 8. STEREO/MONO (ST) When an FM station is weak or distorted, audio may improve by selecting MONO. 9. DISPLAY BUTTON (Set the Clock) Selects radio frequency or clock display. To set the clock: 1. With clock display selected, hold down DISP button until clock display starts flashing. VOL VOL to change hours. change minutes, 2. Rotate VOL to VOL 3. Press DISP button to start clock. 10. MODE BUTTON By pressing this key, user can select. AUX/TUNER/CD-MP3/USB mode. 11. BAND SELECTOR SWITCH Push this switch to select the desired band. OR FREQ DOWN ) 12. AUTOMATIC OR MANUAL TUNING (FREQ UP (A) RADIO MODE When pressed for less than 1 second, these keys operate as manual tuning mode. When pressed longer than 1 second they operate as SEEK tuning mode. If the keys are not pressed for 3 seconds, they will return to SEEK mode again. (B) CD/MP3/WMA PLAYER MODE When pressed for less than 1 second, they will operate as TRACK UP or TRACK DOWN mode. When pressed longer than 1 second they will operate as CUE or REVIEW mode. 13. AUTOMATICALLY STORE STATIONS Select six strong stations and store them in current band. 1. Select a band (if needed) 2. Hold A/PS button for more than three seconds. The new stations replace stations already stored in that band. Preset Scan Scan stations stored in current band 1. Select a band (if needed) 2. Touch A/PS for more than one second but less than three seconds. Radio pauses for five seconds at each station. Touch A/PS again to stop scanning when desired station is reached. 14.‘SCAN’ AUTOMATIC TUNING CONTROL (SCN) This key operates as RADIO SCAN. The function is similar to normal SEARCH but pauses at each stored station for 5 seconds. On the Remote Control: Press “*” to start SCAN function. Press it again to end. When a channel is found, press and hold a preset key (1-6) to store in memory. 15. LCD DISPLAY The Liquid Crystal Display will display the current state of the unit. 16. OPEN THE FRONT PANEL button and the front panel will open. Press CD/MP3/WMA CONTROL Inserting the CD Carefully slide the CD through the CD slot into the mechanism. The CD starts playing automatically. TRACK/SEARCH BUTTON FORWARD AND REVERSE TRACK SEARCH Press and release to advance to next track or to return to the beginning of the current track (track number will be displayed.) Press and hold to fast forward or reverse . Play will begin at the point when you release the button. 17. CD SLOT 18. CD EJECT BUTTON button to remove the CD. The receiver will automatically switch to radio mode. Press the EJECT 19. TOP BUTTON Press to play first song of current folder. 20. PAUSE BUTTON Press BND button to pause CD playback. Press again to resume. 21. INTRO BUTTON (Preview all Tracks) ‘INT’ Press this button to display ‘INT ON’. The first few seconds of each track on the disc will play. Press again to stop intro and listen to selected track. 22. REPEAT BUTTON ‘RPT’ When A/PS button is pressed, ‘RPT ON’ is displayed and the selected track will repeat continually until the Track repeat mode is cancelled by pressing ‘A/PS’ button again. 23. RANDOM BUTTON ‘RDM’ When this button is pressed, ‘RDM ON’ is displayed and each track on the disc will play in random order instead of normal sequence. To cancel RANDOM mode, press ‘RDM’ button (23) again. 24, 25. 10 TRACK UP/DOWN SELECT: (In case of MP3/WMA files) M5: 10 Track down / M6: 10 Track up HOW TO SELECT MP3/WMA FILES 1. Searching Track: • Press and hold “A/PS”. Search track is activated. • Press “VOL” knob. The first digit will flash. • Rotate “VOL knob to right or left”. Select first digit desired. • Press “VOL” knob. The first digit is then fixed and second digit will flash. • Rotate “VOL knob to right or left”. Select 2nd and 3rd respectively. • The song selected will then automatically play. 2. Searching Character: • Press and hold “A/PS”. Press “A/PS” again to activate character search mode. • Press “VOL” knob. “A” character is displayed. • Rotate “VOL knob to right or left” to select the desired letter. • Press “VOL” knob for longer than 2 seconds. The song with this character will display. • Rotate “VOL knob to right or left” to select the desired song. • Press “VOL” knob again. The selected song will now play. 3. Searching File Name: • Press and hold “A/PS”. Press “A/PS” again, then directory search is activated. • Press “VOL” knob. The first directory is displayed. • • • • Rotate “VOL knob to right or left” to select the desired directory. Press “VOL” knob again. The directory is fixed and the first file name is displayed. Rotary “VOL knob to right or left” to select the required file. Press “VOL” knob again. The selected song will now play. Connecting to a Portable MP3 Player 26. FRONT AUX IN This unit is compatible with the audio output of iPod and other MP3 Players. The front “AUX IN” input jack allows easy connection of Portable Media such as iPod or other MP3 Players via the USB or 3.5mm Stereo Jack. More AUX input: Additional auxiliary RCA input jacks on the back of the unit can be used to connect other external audio sources such as a DVD player, Game Console and other portable audio device. 27. USB PORT Use a USB cable to connect your portable MP3 Player. Connecting iPOD Connect iPOD portable devices and play songs through the car stereo. Not all iPOD features may be supported. How to connect iPOD Playing Songs in iPOD Tunes in iPOD can be played once the cable is properly connected. 1. Press MODE until USB-DRIV > I-POD shows in the display. 2. Press and hold A/PS. 3. Rotate VOL to select PLAYLIST - ARTIST - ALBUM - GENRE - SONG - COMPOSER - TRACK. 4. Press VOL. If you are aware of iPOD operating functions, the way to use this car stereo feature is basically the same. Take note of the equivalent key function below. Car Stereo Rotate VOL knob Press VOL knob iPOD Function Rotate CLICK WHEEL Up/down category/file browsing Press SELECT button Selecting a category/Play song Car Stereo and iPOD equivalent key function Note: Please refer to your iPOD user manual for operating instructions. Press A/PS to go back to Main Menu. 10 HOW TO USE BLUETOOTH IN YOUR CAR AUDIO How to Perform Pairing Before dialling out from the car stereo, PAIRING must first be performed. Pairing is a procedure used to connect 2 Bluetooth devices together. 1. Press and hold SEL button for 2 seconds. 2. Press SEL button repeatedly until “PAIRING” displays. 3. Press and hold SEL button to engage pairing mode. “PAIRING” blinks on the display. 4. Turn on the Bluetooth feature of your mobile phone. Perform “Add Bluetooth device” from your mobile phone. The mobile will search for any Bluetooth devices within the range. Select “CAR BLUETOOTH” and enter Passkey: “0000” to connect to the car audio. 5. The LCD will display “PAIRED” when successful. Note: • If “DISCONN” shows instead of “PAIRING”, it means the head unit currently is paired with another device. Press and hold SEL button to disconnect the connection and perform steps above again. • “CAR BLUETOOTH” is the Bluetooth device name of the car stereo. • Refer to your cellular user manual for the proper procedures of pairing Bluetooth devices. Switching to Telephone Mode 1. During any operation mode, press and hold “*” to activate TELEPHONE mode. Press and hold it again to return to previous mode. Making Calls Using the Remote Control Before making calls directly from the remote control ensure that the devices are properly paired and connected. 1. Press and hold “*” on remote control. Unit will switch to phone mode. button to dial out. 2. Enter the phone number via the remote control keypad and press bbutton to make corrections when entering numbers. Press bbutton to end call. 3. Press Audio Streaming If your phone is “A2DP” format compatible, then you can play music in your mobile and the sound will be transferred to the vehicle’s sound system. 1. Mobile phone and the head unit must be properly paired and connected. 2. Play the music through your mobile music player software. 3. Continuously press MODE until “BT-PLAY” appears in the display. The sound will transfer to the head unit. Answering / Hanging Up To answer a call, press the button on the remote control. Once you have finished your conversation, press the button to hang up. Calls (Outgoing, Incoming) The unit stores all the incoming and outgoing calls. Use this feature to check the numbers and make calls. “OUT NUM” – outgoing calls made through the remote control. 1. Press and hold (*) then press and hold SEL button for 2 seconds. “OUT NUM” displays. 2. Press and hold SEL button again. to call. 3. Rotate volume knob to search for entries and press “IN NUM” – incoming calls received. 1. Press and hold (*) then press and hold SEL button for 2 seconds. 2. Press SEL button repeatedly until “IN NUM” displays. 3. Press and hold SEL button again. to call. 4. Rotate volume knob to search for entries and press 11 Adding Contacts The unit can save contact telephone numbers for quick access. 1. Press and hold (*) then press and hold SEL button for 2 seconds. 2. Continuously press SEL button until “ADD NUM” displays. 3. Press and hold SEL button again. 4. Using the volume knob, enter the name of the contact. Press SEL button to save each character entered. 5. Enter the phone number. Press SEL button to save each number entered. 6. Press and hold SEL button to save entry Finding Contacts After adding contacts, you can use this feature to find them. 1. Press and hold (*) then press and hold SEL button for 2 seconds. 2. Continuously press SEL button until “FIND NUM” displays. 3. Press and hold SEL button again. to call. 4. Using volume knob, select the name of the contact and press Deleting Contacts 1. Press and hold (*) then press and hold SEL button for 2 seconds. 2. Press SEL button repeatedly until “FIND NUM” displays. 3. Press and hold SEL button again. 4. Rotate VOL knob until the name of the contact you want to delete displays. ” for 2 seconds to delete contact. 5. Press and hold “ How to Set Incoming Call Melody 1. Press and hold (*) then press and hold SEL button for 2 seconds. 2. Press SEL button repeatedly until “MELODY” displays. 3. Rotate VOL knob to the desired melody. How to Set Incoming Call Ring Volum 1. Press and hold (*) then press and hold SEL button for 2 seconds. 2. Continuously press SEL button until “RING” displays. 3. Rotate VOL knob to the desired level. How to Set Conversation Volume 1. Press and hold (*) then press and hold SEL button for 2 seconds. 2. Continuously press SEL button until “TEL” displays. 3. Rotate VOL knob to the desired level. Disconnect Paired Devices You can disconnect to an already paired Bluetooth device from your car stereo. 1. Press and hold (*) then press and hold SEL button for 2 seconds. 2. Continuously press SEL button until “DISCONN” displays. 3. Press and hold SEL button again to disconnect. RESET A reset button is placed on the front housing. The reset button is to be activated for the following reason: Initial installation of the unit after all wiring is complete. No function buttons operate. Error symbol on the display. 12 RESET CAUTION & MAINTENANCE The detachable panel AM/FM car radio with CD player is an example of superior design and craftsmanship. The following suggestions will help you care for the product and experience many years of enjoyment. 1. Do not touch the contacts on the front panel or the unit body. 2. The product can only operate on 12V-14V DC power supply, negative ground. 3. Avoid exposing your product to high temperature and humidity. 4. Handle the product with care. Dropping it can damage circuit boards and cause the product to malfunction. 5. Modifying or tampering with internal components can cause damage and may invalidate the warranty. 6. Always remove the CD from the unit when it has finished playing or not being used. TROUBLESHOOTING GUIDE SYMPTOM No sound or power POSSIBLE CAUSE Speaker cord disconnected. Bad power connection SOLUTION Check to see that all the power and speaker leads are securely connected. Blown fuse. Replace fuse with same amperage. Mis-adjusted balance control Check balance control. Damaged speaker wire or speaker Reverse left and right channel speaker leads If no sound from other side, check or replace speaker wire. If no sound from both sides, replace both speakers. Poor FM reception Insensitive or defective antenna. Replace with a good sensitivity antenna. CD sound quality poor Disc reading malfunction. Disc may be damaged or dirty. Lens may need cleaning. Try a different disc. Clean Disc with a soft cloth. Insert a quality lens cleaning disc. No sound in one channel ERROR CODE ERROR CD ERROR 1 SLED INITIALIZED ERROR 2 FE BIAS CONTROL ERROR 3 FOCUS SERVO OFFSET / TRACKING SERVO OFFSET / OFFSET CONTROL ERROR 4 FOCUS SEARCH / CLV KICK ERROR 5 TOC READ ERROR 6 RECOVERY ERROR 7 MP3 NO FILE ERROR 8 MP3 READ ERROR ERROR 12 ERROR 13 ERROR 14 ERROR 15 ERROR 16 13 USB TMC51F DATA ERROR TMC51F COMMUNICATION ERROR MS BOOT ERROR TMC51F NO READ ERROR NO FILE ERROR TECHNICAL SPECIFICATIONS CD/MP3/WMA PLAYER SECTION Signal to Noise Ratio > 60 dB Channel Separation > 50 dB (1kHz) Frequency Response20Hz - 20 kHz TUNER (FM) Frequency range 87.5 - 108 MHz Intermediate frequency 10.7 MHz Sensitivity2.8 µV Stereo separation30 dB Signal to noise ratio 50 dB Channel step 100 kHz TUNER (AM) Frequency Range Intermediate Frequency Usable Sensitivity 522 - 1710 KHz 10.71 MHz 32 dBμV GENERAL Power Supply Speaker impedance Output power 12V DC (10.8 - 15.6V allowable) 4 or 8 Ohm 40W x 4CH SUB OUT Frequency Response20 Hz - 50 Hz Sensitivity300 mV Max Output 4V RCA OUT Frequency Response20 Hz - 20 KHz Sensitivity200 mV Output Impedance2 K Max Output 5 Volt (max.) RCA IN Frequency Response20 Hz - 20 KHz Sensitivity 775 mV Input Impedance20 K USB Operation and Compatibility, USB 1.1 , USB 2.0 Full Speed. Bluetooth Version Range Audio V1.2 5M Stereo Audio Streaming DIMENSIONS Chassis Nose piece 178(W)x50(H)x158(D) mm 7(W)x2(H)x6.2(D) inch 188(W)x58(H)x20(D) mm 7.4(W)x2.3(H)x0.8(D) inch Note: This unit has been designed to be compatible with the latest MP3 and USB technology. There is a wide variety of memory cards, USB sticks and software formats available. However not all may be compatible with this product. Specification and design is subject to improvement and modification without notice. 14 WARRANTY Congratulations on your purchase of a quality Mobile Audio System! You’re joining thousands of satisfied customers who enjoy & experience the benefits of the products we distribute. In the unlikely event that some technical difficulty arises with your purchase, be assured that we are most anxious to see that the problem is quickly rectified to your satisfaction. Please familiarise yourself with the following simple conditions of our warranty. This warranty covers faults through component failure of the product to operate in accordance with published specifications. Product failure as a result of unreasonable environmental conditions, accident, misuse, improper installation, unauthorised repair, vehicle electrical or wiring faults or neglect etc, will not be covered by this warranty. Removal and installation costs, if any, would be paid by the owner as well as any freight or postage costs of transporting the product to AudioXtra. AudioXtra shall not be liable or responsible for any loss of use of this product or any form of consequential loss. CONSUMER WARRANTY This product is warranted by AudioXtra International Pty Ltd to be free from defects in materials and workmanship under NORMAL USE for a period of TWENTY FOUR MONTHS from the date of purchase. WITHIN 30 DAYS OF PURCHASE DATE: Please return the unit for replacement to our National Service Centre or the Retailer from where you made the purchase. All accessories must be included. Proof of purchase date must accompany the product. AFTER 30 DAYS OF PURCHASE DATE: Warranty repair and service is carried out by our National Service Centre. Repair and service will be carried out at no cost to the owner if proof of ownership and the date of purchase can be verified to the satisfaction of the authorised centre concerned with this repair. This proof should take the form of either: a) The warranty card accompanying this product, stamped and dated by the dealer. b) A Tax Invoice or Receipt showing full details of original vendor, purchaser, model number and serial number. COMMERCIAL WARRANTY: A product used in or associated with a commercial application will carry a limited SIX MONTH warranty. An abnormal commercial application is one where usage, dust, vibration, heat/cold and other environmental conditions exist at an extreme level. Please complete details below in the event of warranty service being required. Purchaser’s Name: Purchaser’s Address: Model Number: Dealer Name: Dealer Address: AX-902 Serial Number: Date of Purchased: / / Invoice/Sales Docket no: General Hints : To expedite service and prompt return of the equipment, please: a) Clearly describe the fault in detail b) Safety and security pack the unit for transport c) Include your return address d) Provide proof of purchase date as outlined above National Service Centre: 10 STODDART ROAD, PROSPECT, SYDNEY NSW 2148 Australia Telephone: (02) 9631 4199 Fax: (02) 9636 1204 email: [email protected] www.audioxtra.com.au
