Download 12x12W LED Moving Head FX Light Manual
Transcript
12x12W MOVING HEAD LED SPOT FX LIGHT USER MANUAL .1. TABLE OF CONTENTS Maintenance----------------------------------------------------1 Statement-------------------------------------------------------1 Attention Item -------------------------------------------------2 Product introduction ------------------------------------------2 13 Control Channel -------------------------------------------3 Control Board--------------------------------------------------4 Controller Connection Diagram-----------------------------5 Maintenance 1. Please keep the light in dryness and avoiding use in wet place. 2. Using intermittently can be extended the life. 3. Attention to clean the fan and lens usually in order to get the ventilating effects and lighting effects better. 4. Please do not wipe the crust using organic menstruum for avoid to damage the product. Statement The product has well capability and intact packing when leave factory. All of the user should comply with above warning item and manual, any misuse cause of the damages are not included in our guarantee, and also can not be responsible for any malfunction & problem owing to ignore the manual. Please forgive that we will not be notice for technical change. .6. .5. Controller connection diagram Attention Item XLR-connection DMX512 LINK 2 1 3 PIN1 = Ground PIN2 = Signal PIN3 = Signal + Input 1 2 3 Output Out XLR-Signal wire Out In Out In Light 1 Out In Light 2 Out In Light 3 .2. 1. For guarantee the life of product, please don't put it on the wet place and also not use it in the place over 40 degree. 2. Please don't lay the product on the unfixable or shakable place. 3. Ask for the professional to maintain the product in order to avoid the danger of get an electric shock. 4. Power supply should not be changed over 10% while the light is using, it will be decreased the life of lamp if the power is too high, but it will be influenced the luminosity if the power is too low. 5. After power off, if it is need used again, please cool down over 20 minutes. 6. Please look round the manual for ensure the product can be used normally. Light 4 Product introduction Power supply: AC100~230V, 50Hz Power consumption: 150W Fiting lamp: 12x12W RGBW LED DMX-control-channels: 15 Color: RGBW color-mixture Shuttle: Flash rate: 0-13Hz Dimmer: 0~100% mechanic dimmer Maximum PAN-movement: 540 Maximum TILT-movement: 180 Master/Slave ativated by sound at pre-programmed function. .3. .4. 13 Control Channel Control Board Accept DMX512 control channel, detail as follow: Channel 1 PAN 2 TILT 3 PIN 16bit 4 TILT 16bit 5 Dimmer 6 Shutter 7 LED_RED 8 LED_GREEN 9 LED_BLUE 10 LED_WHITE 11 LED macro DMX-value 0~255 0~255 0~255 0~255 0~255 0~7 0~255 0~255 0~255 0~255 0~255 0~10 11~120 12 121~180 LED effect 181~244 245~255 13 Effect speed 0~255 14 X/Y speed 0~255 0~244 15 Reset 245~255 Feature 540 180 PAN 16 bit spinner When navigating the menu: Use the <UP> button to move up. Use the <DOWN> button to move down. Use the <ENTER> button to move right. Use the <MODE> button to move left, or to scroll through the left-most items in the menu map. TILT 16 bit spinner 100~0% electrical dimmer Strobe effect with increasing speed Dimmer for Red 0~100% Dimmer for Green 0~100% Dimmer for Blue 0~100% Dimmer for White 0~100% LED macro effect No function Step change Gradual change Mixed effect Sound control LED effect change speed PAN / TILT controllable speed with decreasing No function Reset Use the <MODE/ESC> button to scroll through these menu items DMX-ADR 001 DMX mode: select channel 1 - channel 512 Use the <UP>,<DOWN>, and <ENTER> button to scroll through these menu items DMX-ADR 512 ADJ-R 255 ADJ-R 001....255 RED adjust ADJ-G 255 ADJ-G 001....255 GREEN adjust ADJ-B 255 ADJ-B 001....255 BLUE adjust ADJ-W 255 ADJ-W 001....255 WHITE adjust PROGRAM 001 PROGRAM 001....13 Program select ADJ-S 001 ADJ-S 001....016 Program speed TEST MOD AUTO-MD TEST MOD AUTO-MD Auto control mode TEST MOD SOUND-MD Sound control mode RESET ? Reset