1
Download AJ65BT-R2N
Transcript
July 2007 New Product Release Open Field Network CC-Link No. 298E AJ65BT-R2N RS-232 Interface Module Improved operability with new functions! Program startup and modification available on site! Online operations are available by connecting GX Developer or GOT, improving debug and maintenance efficiency. Supports transmission speed of 115.2 kbps! Easy to set up when connecting multiple modules! Sequence program is simplified, improving program development efficiency. Master station Read MITS UBIS HI M ELSE C AJ6 5B T-R2N GX Developer Barcode reader PW RUN L RU N SD RD L ER R. 1 3 DA 5 DG 2 4 DB 7 +24V 6 SLD RS-23 2 SD RD ERR. RS-23 24G XC XD YC YD B RA TE ST AT X10 ION NO. 0 1 X1 4 2 3 0 1 4 2 3 0 1 4 MODE SW 123 2 456 2 3 78 ON (FG) RESE T I/O AJ65 1 3 2 5 4 RFID controller Read/write head Data carrier 7 6 AJ65BT-R2N R2N GOT Read/write RFID Features 1. Program startup and modification available on site MELSOFT connection mode Online operations such as monitoring and testing are available by connecting AJ65BT-R2N to GX Developer or GOT. The program can be started and modified right by the AJ65BT-R2N module (away from the master station), improving work efficiency. Master station GX Developer The system can be monitored and tested right by the equipment. Programs can be modified without connecting to the master station. MITS UBISH I MEL SEC AJ65BT-R2 N PW RUN L RUN SD RD L ERR . 1 3 DA 5 DG 2 4 DB 6 SLD RS-2 32 SD RD ERR. B RAT E XC XD YC YD 0 1 4 RS-2 2 3 STATION X10 NO. X1 0 1 4 MOD 7 +24V 2 3 1 4 123 456 2 3 78 ON (FG) RESET I/O AJ65 1 3 2 Handy GOT 0 E SW 32 24G 5 4 7 6 AJ65BT-R2N R2N Operations using a handy GOT when needed. 2. Easy to set up when connecting multiple modules! Nonprocedural protocol mode When the buffer memory auto-refresh function is used, the auto-refresh buffer size needs to be changed to connect three or more modules. This can be easily carried out by setting the mode switch. A program for initial settings is no longer required, enhancing development efficiency. (E.g.) Configuring a system with 8 modules 8 modules connected Previously M115 M120 34 MOV M107 M115 M120 G.RITO 34 M107 M115 M120 34 M107 M115 M120 G.RITO U1 M107 M115 34 M120 U1 U1 K8 G.RITO M107 34 G.RITO U1 K20 H112 K8 MOV D13 D13 MOV K1 K20 K20 H112 H11A U1 K8 D14 MOV MOV K0 K8 H11A G.RITO U1 D13 D14 D13 MOV K1 K20 H112 K1 K20 MITSU BISH I ME LSEC D13 D14 D13 MOV D15 D14 MOV K1 K20 D13 K1 K20 H112 D14 D13 K1 MOV K20 D13 D15 K1 MOV K0 D15 K8 H11A D14 K1 M115 M120 MOV K20 D14 G.RITO U1 K8 H112 D13 K1 MOV K20 G.RITO U1 K8 H28 D15 K1 G.RITO U1 K8 H24 D15 K1 MOV K0 D15 G.RITO U1 K8 H11A D14 K1 M107 M115 M120 MOV K20 D14 G.RITO U1 K8 H112 D13 MOV G.RITO U1 K8 H2C D15 K1 G.RITO U1 K8 H28 D15 K1 G.RITO U1 K8 H24 D15 K1 MOV K0 D15 G.RITO U1 K8 H11A D14 K1 M107 M115 M120 MOV K20 U1 K8 H112 U1 K8 H30 D15 K1 G.RITO 34 G.RITO G.RITO U1 K8 H2C D15 K1 G.RITO U1 K8 H28 D15 K1 G.RITO U1 K8 H24 D15 K1 MOV K0 D15 G.RITO U1 K8 H11A D14 MOV MOV H20 D16 U1 K8 G.RITO U1 K8 H30 D15 K1 G.RITO G.RITO U1 K8 H2C D15 K1 G.RITO U1 K8 H28 D15 K1 G.RITO U1 K8 H24 D15 K1 MOV K0 U1 K8 H11A MOV H1C0 D17G.RITO MOV H20 D16 G.RITO U1 K8 H30 D15 K1 G.RITO U1 K8 H2C D15 K1 G.RITO U1 K8 H28 D15 K1 G.RITO U1 K8 H24 D15 MOV MOV H1E0 D18 U1 K8 MOV H1C0 D17G.RITO MOV H20 D16 G.RITO U1 K8 H30 D15 K1 G.RITO U1 K8 H2C D15 K1 G.RITO U1 K8 H28 D15 U1 K8 H24 G.RITO U1 K8 H1 D16 K1 G.RITO MOV H1E0 D18 MOV H1C0 D17 MOV H20 D16 G.RITO U1 K8 H30 D15 K1 G.RITO U1 K8 H2C D15 U1 K8 H28 G.RITO U1 K8 H3 D16 K1 G.RITO G.RITO U1 K8 G.RITO U1 K8 H1 D16 K1 MOV H1E0 D18 MOV H1C0 D17 MOV H20 D16 G.RITO U1 K8 H30 D15 U1 K8 H2C G.RITO U1 K8 H18 D16 K1 G.RITO G.RITO U1 K8 G.RITO U1 K8 H3 D16 K1 G.RITO U1 K8 H1 D16 K1 MOV H1E0 D18 MOV H1C0 D17 MOV H20 U1 K8 H30 G.RITO U1 K8 H1B D17 K1 G.RITO G.RITO U1 K8 G.RITO U1 K8 H18 D16 K1 G.RITO U1 K8 H3 D16 K1 G.RITO U1 K8 H1 D16 K1 MOV H1E0 D18 MOV H1C0 MOV G.RITO U1 K8 H1C D16 K1 U1 K8 G.RITO U1 K8 H1B D17 K1 G.RITO G.RITO U1 K8 H18 D16 K1 G.RITO U1 K8 H3 D16 K1 G.RITO U1 K8 H1 D16 K1 MOV H1E0 MOV G.RITO U1 K8 H1F D18 K1 G.RITO U1 K8 H1C D16 K1 G.RITO U1 K8 H1B D17 K1 G.RITO U1 K8 H18 D16 K1 G.RITO U1 K8 H3 D16 K1 G.RITO U1 K8 H1 D16 MOV SET M120 G.RITO U1 K8 H1F D18 K1 G.RITO U1 K8 H1C D16 K1 G.RITO U1 K8 H1B D17 K1 G.RITO U1 K8 H18 D16 K1 G.RITO U1 K8 H3 D16 G.RITO U1 K8 H1 SET M120 G.RITO U1 K8 H1F D18 K1 G.RITO U1 K8 H1C D16 K1 G.RITO U1 K8 H1B D17 K1 G.RITO U1 K8 H18 D16 G.RITO U1 K8 H3 G.RITO U1 K8 SET M120 G.RITO U1 K8 H1F D18 K1 G.RITO U1 K8 H1C D16 K1 G.RITO U1 K8 H1B D17 G.RITO U1 K8 H18 G.RITO U1 K8 SET M120 G.RITO U1 K8 H1F D18 K1 G.RITO U1 K8 H1C D16 G.RITO U1 K8 H1B G.RITO U1 K8 G.RITO 34 K8 G.RITO 34 U1 K8 G.RITO K8 AJ65BT- R2N H24 U1 D14 D13 MOV K1 K20 H112 D15 D14 MOV K1 K0 H11A K1 D15 MOV D13 K1 K20 D13 D14 D13 K1 K1 K20 D14 D15 D14 K1 K0 K1 K1 D15 K1 K1 D15 H28 K1 D15 K1 D16 D15 H2C K1 D15 K1 D17 H20 H30 D16 D15 K1 D18 H1C0 MOV D17 H20 D16 K1 H1E0 MOV D18 H1C0 D17 K1 D16 MOV K1 H1E0 D18 K1 D16 H1 K1 D16 K1 K1 D16 H3 K1 K1 D16 K1 K8 U1 G.RITO SET M120 H1F D18 K1 K8 H1C D16 U1 K8 H1B K1 D17 K1 G.RITO U1 G.RITO K8 U1 SET H1F K8 M120 D18 H1C K1 D16 K1 G.RITO U1 K8 SET H1F M120 D18 K1 3 DA 5 DG 2 4 DB 7 RS-23 2 SD RD ERR. RS-23 2 +24V 24G 6 SLD (FG) XC XD YC YD B RA TE STA TIO X10 N NO. 0 1 X1 4 2 3 0 1 4 2 3 0 123 456 Simple! 1 4 MODE SW 2 3 78 ON RESE T I/O AJ65 1 3 2 5 4 7 6 R2N MODE A M120 F01 789 Program to change auto-refresh buffer size for 8 modules required 3456 K1 D16 K1 D17 H18 U1 G.RITO PW RUN L RU N SD RD L ER R. 1 D15 K1 D15 H24 SET Complicated programming! 2 G.RITO D13 K1 K20 BCDE M107 Now Set the MODE switch to "3" only! 1 Performance specifications Item AJ65BT-R2N (New model) AJ65BT-R2 (Previous model) RS-232 compliant (D-Sub 9P) Interface Full-duplex communication method Communication method Asynchronous method Synchronization method 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, Transmission speed RS-232 Data format Up to 15 m Start bit 1 Data bit 7/8 Parity bit 1 (vertical parity)/No Stop bit Error detection 1/2 Parity check Yes (even/odd number)/No DTR/DSR (ER/DR) control Communication control (flow control) DC1/DC3 control OS reception area 5120 bytes Nonprocedural protocol Protocol CC-Link Bus (RS-485) CC-Link station type Intelligent device station CC-Link version Ver.1 CC-Link dedicated cable/CC-Link high-performance cable/CC-Link Ver. 1.10-compatible cable Connection cable 1 station (RX/RY: 32 points each, RWw/RWr: 4 points each) Number of occupied stations Number of writes to E2PROM Dielectric withstand voltage Up to 100,000 times Between all external DC terminals and ground: 500 V AC for 1 minute Between all external DC terminals and ground: 10 MΩ or more by 500 V DC insulation resistance tester Insulation resistance Noise immunity By noise simulator of 500 Vp-p noise voltage, 1 µs pulse width, and 25 to 60 Hz noise frequency M4 x 0.7 mm x 16 mm or larger, also mountable with DIN rail Module mounting screw Applicable DIN rail TH35-7.5Fe, TH35-7.5AI, TH35-15Fe (conforms to IEC 60715) 24 V DC (20.4 to 26.4 V DC, ripple ratio: within 5%) External power supply Current consumption: 0.11 A (TYP. 24 V DC) Allowable momentary power failure time 1ms Number of input points 2 points Photocoupler Isolation method Rated input voltage 24 V DC Rated input current Approx. 7 mA Operating voltage range 19.2 to 28.8 V DC (ripple ratio: within 5%) Max. number of simultaneous input points 100% ON voltage/ON current 14 V or higher/3.5 mA or higher 6 V or lower/1.7 mA or lower OFF voltage/OFF current Approx. 3.3 kΩ Input resistance Response time OFF to ON 10 ms or less ON to OFF 10 ms or less Wiring method for common 2 points/common, positive/negative common (sink/source) Number of output points 2 points Isolation method Photocoupler 12 to 24 V DC (+20/-15%) Rated load voltage 10.2 to 28.8 V DC (ripple ratio: within 5%) Operating load voltage range 0.1A/point, 0.2A/common Max. load current 0.7 A, 10 ms or less Max. inrush current 0.4 A, 10 ms or less Leakage current at OFF Max. voltage drop at ON 0.1 mA or less 0.1 V DC (TYP.) at 0.1 A 1.5 V DC or lower (MAX.) at 0.1 A 0.2 V DC (MAX.) at 0.1 A Output type Response time Sink OFF to ON 1 ms or less 2 ms or less ON to OFF 1 ms or less (resistance load) 2 ms or less (resistance load) Voltage External power supply for output Current 10.2 to 28.8 V DC (ripple ratio: within 5%) 10 mA (at 24 V DC) 2 points/common Yes No External connections 7-point terminal block (M3.5 screw) 0.75 to 2 mm2 Applicable wire size Applicable crimping terminal excluding external load current Zener diode Wiring method for common Protection function 50 mA or lower (TYP. 24 V DC/common) (MAX all points ON) Surge suppressor External dimensions Nonprocedural protocol MELSOFT connection (equivalent to AJ65BT-G4-S3 Q mode) Transmission path General-purpose I/O 300, 600, 1200, 2400, 4800, 9600, 19200 bps 57600*1, 115200*1 bps Transmission distance RAV1.25-3.5, RAV2-3.5 (conforms to JIS C 2805) 80 (H) x 170 (W) x 47 (D) [mm] Weight 80 (H) x 170 (W) x 63.5 (D) [mm] 0.40 kg *1: Unless data are sent concurrently from the AJ65BT-R2N and external-device sides in Nonprocedural protocol mode, communication at 57600 bps or 115200 bps is available. In the event of concurrent transmission, an RS-232 receive overrun error (BB23H) may occur. 2 4.5 (0.18) Unit: mm (inch) 47.5 (1.87) 71 (2.79) 2-ø4.5 mounting hole (M4 mounting screw) 80 (3.14) AJ65BT-R2N 4.5 (0.18) External dimensions 161 (6.33) DIN rail center 170 (6.69) Product list Model Model code AJ65BT-R2N 1W5312 Product name RS-232 interface module Manuals Manual supply status IB/SH No. Model code Included IB-0800381-A 13JY30 CC-Link System RS-232 Interface Module User's Manual (Nonprocedural Protocol Mode) Sold separately SH-080685ENG-A 13JZ00 CC-Link System RS-232 Interface Module User's Manual (MELSOFT Connection Mode) Sold separately SH-080687ENG-A 13JZ01 Manual name CC-Link System RS-232 Interface Module User's Manual (Hardware) Country/Region Sales office Tel/Fax Country/Region Sales office Tel/Fax USA Mitsubishi Electric Automation Inc. 500 Corporate Woods Parkway, Vernon Hills, IL 60061, USA Tel: +1-847-478-2100 Fax: +1-847-478-0327 Taiwan Tel: +886-2-2299-2499 Fax: +886-2-2299-2509 Brazil MELCO-TEC Rep. Com.e Assessoria Tecnica Ltda. Tel: +55-11-5908-8331 Rua Correia Dias, 184, Edificio Paraiso Trade Center-8 andar Fax: +55-11-5574-5296 Paraiso, Sao Paulo, SP Brasil Setsuyo Enterprise Co., Ltd. 6F, No.105 Wu-Kung 3rd Rd, Wu-Ku Hsiang, Taipei Hsine, Taiwan Korea Mitsubishi Electric Europe B.V. German Branch Gothaer Strasse 8, D-40880 Ratingen, Germany Tel: +49-2102-486-0 Fax: +49-2102-486-1120 Mitsubishi Electric Automation Korea Co., Ltd. 3F, 1480-6, Gayang-dong, Gangseo-gu, Seoul 157-200, Korea Tel: +82-2-3660-9552 Fax: +82-2-3664-8372 Germany Singapore UK Mitsubishi Electric Europe B.V. UK Branch Travellers Lane, Hatfield, Hertfordshire, AL10 8XB, UK Tel: +44-1707-276100 Fax: +44-1707-278992 Mitsubishi Electric Asia Pte, Ltd. 307 Alexandra Road #05-01/02, Mitsubishi Electric Building Singapore 159943 Tel: +65-6470-2460 Fax: +65-6476-7439 Italy Mitsubishi Electric Europe B.V. Italian Branch Viale Colleoni 7 1-20041 Agrate Brianza (Milano), Italy Tel: +39-39-60531 Fax: +39-39-6053312 Thailand Mitsubishi Electric Automation (Thailand) Co., Ltd. Bang-Chan Industrial Estate No.111, Soi Serithai 54, T. Kannayao, 10230 Thailand Tel: +66-2-517-1326 Fax: +66-2-906-3239 Spain Mitsubishi Electric Europe B.V. Spanish Branch Carretera de Rubi 76-80 E-08190 Sant Cugat del Valles (Barcelona), Spain Tel: +34-93-565-3131 Fax: +34-93-589-1579 Indonesia France Mitsubishi Electric Europe B.V. French Branch Tel: +33-1-5568-5568 25, Boulevard des Bouvets, F-92741 Nanterre Cedex, France Fax: +33-1-5568-5757 P.T. Autoteknindo Sumber Makmur Tel: +62-21-663-0833 Muara Karang Selatan Block A/Utara No.1 Kav. Fax: +62-21-663-0832 No.11, Kawasan Industri/ Pergudangan, Jakarta - Utara 14440, P.O. Box 5045 Jakarta 11050, Indonesia India South Africa Circuit Breaker Industries Ltd. Private Bag 2016, ZA-1600 Isando, South Africa Tel: +27-11-928-2000 Fax: +27-11-392-2354 Messung Systems Pvt., Ltd. Electronic Sadan NO: III Unit No.15, M.I.D.C. Bhosari, Pune411026, India Tel: +91-20-2712-3130 Fax: +91-20-2712-8108 Hong Kong Mitsubishi Electric Automation (Hong Kong) Ltd. 10F, Manulife Tower, 169 Electric Road, North Point, Hong Kong Tel: +852-2887-8870 Fax: +852-2887-7984 Australia Mitsubishi Electric Australia Pty. Ltd. 348 Victoria Road, Rydalmere, NSW 2116, Australia Tel: +61-2-9684-7777 Fax: +61-2-9684-7245 China Mitsubishi Electric Automation (Shanghai) Ltd. 4F Zhi Fu Plazz, No. 80 Xin Chang Road Shanghai 200003, China Tel: +86-21-6120-0808 Fax: +86-21-6121-2444 HEAD OFFICE: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN NAGOYA WORKS: 1-14, YADAMINAMI 5, HIGASIKU, NAGOYA, JAPAN 0707 (MDOC) Specifications subject to change without notice. Printed in Japan on recycled paper.
