Download USB to RS-232 Converter with galvanic isolation ADA - CEL-MAR

ADA-I9110
User Manual
ADA-I9110
USB to RS-232 Converter with galvanic isolation
Copyright © 2001-2012 CEL-MAR sp.j.
1
io_ada-i9110_en_v3.22
ADA-I9110
Contents
1. GENERAL INFORMATION...................................................................................................................................................................... 3
1.1. WARRANTED INFORMATION ...................................................................................................................................................... 3
1.2. GENERAL CONDITIONS FOR SAFE USE.................................................................................................................................... 3
1.3. CE LABEL....................................................................................................................................................................................... 3
1.4. ENVIRONMENTAL PRESERVATION............................................................................................................................................ 3
1.5. SERVICE AND MAINTENANCE..................................................................................................................................................... 3
2. PRODUCT INFORMATION................................................................................................................................................................... 3
2.1. PROPERTIES................................................................................................................................................................................. 3
2.2. DESCRIPTION................................................................................................................................................................................ 4
3. CONFIGURATION .................................................................................................................................................................................. 4
4. INSTALLATION....................................................................................................................................................................................... 4
4.1. CONVERTER CONNECTION TO RS-232 INTERFACE OF DEVICE............................................................................................4
4.2. CONNECTION TO COMPUTER'S USB INTERFACE.................................................................................................................... 5
4.3. POWER SUPPLY........................................................................................................................................................................... 5
5. DRIVERS INSTALLATION IN SYSTEM WINDOWS .............................................................................................................................. 5
5.1. EXAMPLE DRIVER INSTALLATION IN WINDOWS 7 SYSTEM...................................................................................................5
6. DRIVER UNINSTALLATION.................................................................................................................................................................. 11
6.1. DRIVER UNINSTALLATION IN WINDOWS 98/ME SYSTEMS...................................................................................................11
6.2. DRIVER UNINSTALLATION IN WINDOWS 2000/XP/2003/VISTA/7/2008 SYSTEMS...............................................................12
6.2.1. EXAMPLE DRIVER UNINSTALLATION IN WINDOWS 7 SYSTEMS.................................................................................12
6.3. EMERGENCY DRIVER UNINSTALLATION................................................................................................................................. 13
6.3.1. EMERGENCY DRIVER UNINSTALLATION IN WINDOWS 98/ME/2000...........................................................................13
6.3.2. EMERGENCY DRIVER UNINSTALLATION IN WINDOWS XP/2003/Vista/7/2008..........................................................13
7. USING................................................................................................................................................................................................... 13
7.1. BAUD RATE SELECTION FOR PROFIBUS COM PORT...........................................................................................................13
7.2. SELECTION OF COM PORT GREATER THEN COM9..............................................................................................................13
8. VERSIONS............................................................................................................................................................................................ 13
9. RS232 INTERFACE – PIN DESCRIPTION OF D-SUB9-MALE SOCKET............................................................................................14
10. SPECIFICATION................................................................................................................................................................................. 14
2
ADA-I9110
1. GENERAL INFORMATION
Thank you for your purchase of CEL-MAR Company product. This product has been completely tested and is covered by a two year
warranty on parts and operation from date of sale.
If any questions or problems arise during installation or use of this product, please do not hesitate to contact Technical Support at +48
41 362-12-46 or e-mail [email protected].
1.1. WARRANTED INFORMATION
The ADA-I9110 converter is covered by a two year warranty from date of sale. In case of being damaged it will be repair or the
damaged component will be replace. The warranty does not cover damage caused from improper use, materials consumption or any
unauthorized changes. If the product does not function (is damaged), or not operate in accordance with the instructions, will be
repaired.
All warranty and no warranty repairs must be returned with paid transport and insuring to the CEL-MAR Company.
CEL-MAR Company under no circumstances won't be responsible for ensuing damage from improper using the product or as a result
of random causes: the lightning discharge, the flood, the fire and the like.
CEL-MAR Company is not be held responsible for damages and loss including: loss of profits, loss of data, pecuniary losses ensuing
from using or the impossibility of using this product.
In specific cases CEL-MAR Company discontinue all warranties and in particular do not follow the user manual and do not accept
terms of warranty by the user.
1.2. GENERAL CONDITIONS FOR SAFE USE
The device should be installed in a safe and stable places (eg, electroinstallation cabinet), the powering cable should be arranged so
as not to be exposed to trampling, attaching, or pulling out of the circuit.
Do not put device on the wet surface.
Do not connect devices for nondescript powering sources,
Do not damage or crush powering wires.
Do not make connection with wet hands.
Do not adapt, open or make holes in casings of the device!
Do not immerse device in water or no other liquid.
Do not put the fire opened on device sources: candles, an oil lamps and the like.
Complete disable from the supply network is only after disconnecting the power supply circuit voltage.
Do not carry out the assembly or disassembly of the device if it is enabled. This may result to short circuit and damage the device.
1.3. CE LABEL
The CE symbol on the device CEL-MAR means compatibility with electromagnetic compatibility Electromagnetic
Compatibility Directive EMC 2004/108/WE. Declaration of Conformity is available by contact with Technical Service
(email: [email protected]; phone: +48 41 362-12-46).
1.4. ENVIRONMENTAL PRESERVATION
This sign on the device inform about putting expended device with other waste materials. Device should send to the
recycling. (In accordance with the act about the Electronic Appliance Expended from day 29 of July 2005)
1.5. SERVICE AND MAINTENANCE
The ADA-I9110 converter does not require the servicing and maintenance.
Technical support is available at number +48 41 362-12-46 in 8.00-16.00, from Monday to Friday or e-mail [email protected].
2. PRODUCT INFORMATION
Converter is delivered with: user manual, CD-ROM with software.
2.1. PROPERTIES
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Conversion of USB to RS-232 standard,
Compliant with USB1.1 and USB 2.0 standard,
Transmitted signals: Rx, Tx, RTS, CTS, DTR, DSR, DCD, RI,
Baud rate (bps): 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600,
PROFIBUS baud rate ( bps): 300 bps, 600 bps, 1200 bps, 2400 bps, 4800 bps, 9600 bps,19200 bps, 93750(230400) bps,
187500(460800) bps, 500000(921600) bps.
Transparent for all protocols: MODBUS, DNP, PROFIBUS and other,
Any format of byte defined with the specification of RS232 interface,
Automatic data flow control (RTS-TOGGLE function),
Power supply from the USB port,
2,5kV= optoisolation in signal channel between USB and RS-232 interface,
1kV= or 3kV= galvanic isolation in power supply channel between USB and RS232,
RS-232 interface connection via DSUB-9 male connector,
Connection USB interface via USB-type A connector,
USB interface, socked B-type,
Interface casing,
Casing dimensions (W x D x H) 84mm x 23mmx 59mm.
3
ADA-I9110
2.2. DESCRIPTION
ADA-I9110 converts USB to RS-232 without interfering in the format of transmitted data. Converter uses transmission lines as Rx, Tx,
RTS, CTS, DTR, DSR, DCD, RI and GND (ground) to communicate with RS-232 interface devices and it is automatically detect by
the computer system after connecting to USB network (Plug&Play device). This converter doesn't required external power supply (it is
powered from USB bus) and it uses asynchronism baud rate up to 921,3 kbps. ADA-I9110 has implemented optoisolation in signal
channel between USB and RS-232 and 1kV= or 3kV= galvanic isolation in the power circuit.
Purchasing the converter you will also receive drivers for Windows 98, ME, NT, 2000, XP, Vista, Linux. Installing this software on
Operating System it add the additional COM port about the next free number, witch can be used as standard COM port. It is virtual
COM port therefore some software use DOS can work improperly but it's considerably faster then standard port – baud rate up to
921,6 kbps.
3. CONFIGURATION
Converter can be configured by using TOG switch (Fig.1) to operate with data flow control of RTS-TOGGLE type or without this
control,.
Converter ADA-I9110 can be connected to the converter ADA-1040 (RS232 to RS485/RS422) using the RTS-TOGGLE control type,
allowing correct operating on 2-wires RS-485 bus (control operation of the 485 transmitter using the RTS signal from ADA-I9110).
Options TOG Switch are described in the Table bellow.
TOG Switch
Description
ON
Operating of RTS line in RTS-TOGGLE mode of RS232 interface of ADA-I9110
OFF
Standard operating of RTS line RS232 interface of ADA-I9110
ON
ADA-I9110
59mm
USB TO RS-232
ISOLATED CONVERTER
OFF
TOG
Tx
Rx
RTS CTS
PWR
DTR DSR
DCD
RI
23mm
84mm
Fig. 1 ADA-I9110 view
4. INSTALLATION
This chapter will show you correctly connection of the ADA-I9110 to USB and RS-232 interface.
4.1. CONVERTER CONNECTION TO RS-232 INTERFACE OF DEVICE
Connection should be done in use of shielded cable (RS232 extender) ended DB-9M male plug, max. lengths up to 15m.
1 DCD
2 RX
3 TX
4 DTR
5 GND
DSR 6
RTS 7
CTS 8
RI 9
Fig. 2 Signal configuration of RS-232 interface in converter DB-9M (mail) connector
4
ADA-I9110
Computer
ADA-I9110
RS232
DB-9M
connector
USB cable
type A-B
USB
connector
type A
USB
connector
type B
Device with RS-232
(DTE) interface
RS232
DB-9M
connector
DCD - 1
RX - 2
TX - 3
DTR - 4
DSR - 6
RTS - 7
CTS - 8
1 - DCD
2 - RX
3 - TX
4 - DTR
6 - DSR
7 - RTS
8 - CTS
RI - 9
GND - 5
9 - RI
5 - GND
Transmission direction
Fig. 3 Converter connection to DTE type device (e.g. PC) with RS-232 interface
Computer
ADA-I9110
RS232
DB-9M
connector
USB cable
type A-B
USB
connector
type A
USB
connector
type B
Modem with RS-232
(DCE) interface
RS232
DB-9M
connector
DCD - 1
RX - 2
TX - 3
DTR - 4
DSR - 6
RTS - 7
CTS - 8
1 - DCD
2 - RX
3 - TX
4 - DTR
6 - DSR
7 - RTS
8 - CTS
RI - 9
GND - 5
9 - RI
5 - GND
Transmission direction
Fig. 4 Converter connection to DCE type device (e.g. modem) with RS-232 interface
4.2. CONNECTION TO COMPUTER'S USB INTERFACE
ADA-I9110 converter connection to computer should be done by use USB cable with A type connector.
4.3. POWER SUPPLY
ADA-I9110 converter is fed from USB port of PC. After connection to USB port of computer, green LED PWR should be ON. If doesn't
you should check:
–
the computer is running,
–
the connection of converter cable to PC,
–
hibernation mode of PC isn't ON,
5. DRIVERS INSTALLATION IN SYSTEM WINDOWS
Converter ADA-I9110 is purchased with the driver package Installer for Windows systems on CD-ROM.
For installation follow the steps below:
a/ insert the CD-ROM to optical driver of the computer,
b/ the installation wizard will run automatically, if not double click ADAUSBDRV.exe.
c/ following the steps of installation wizard, will be installed the Drivers and Uninstaller for the Windows systems 98, ME, 2000, XP,
2003, Vista, Win7, 2008,
d/ connect the convert to USB port of computer and follow the steps of installation wizard.
5.1. EXAMPLE DRIVER INSTALLATION IN WINDOWS 7 SYSTEM
Together With ADA-I9110 converter is delivered CD-ROM with drivers for the system: Windows 98/ME/2000/XP/Vista/7/2008 for the
baud rates:
a/ Standard
b/ Profibus
Driver installation have to be done from the account with Administrator permissions.
For the Drivers installation in Windows 7 system follow the steps bellow:
5
ADA-I9110
a/ insert the CD-ROM to optical driver of computer,
b/ the installation wizard will run automatically, if not double click ADAUSBDRV.exe form the CD-ROM.
After running the installer, the wizard installation window will appear.
Press [Next]
Select STANDARD Drivers and press [Next]
6
ADA-I9110
Press [Install]
Press [Next], will be installed Drivers for USB Bus.
7
ADA-I9110
Press [Install this driver software anyway]. Installation of drivers for USB Bus will start.
8
ADA-I9110
Press [Install this driver software anyway]. Installation of drivers for Virtual Port will start.
9
ADA-I9110
Press [Finish]
Press [Finish].
The driver for ADA-I9110 have been installed. This can be checked in “Uninstall or change a program“.
10
ADA-I9110
Now you can connect ADA-I9110 to computer port.
After connection will appear the Tool tip with [Your device is ready to use]. To see the details press the Tooltip, and will appear
information window where you can see which COM port was assigned to converter.
After this installation, RS232 port of ADA-I9110 converter is available in the system as normal COM port. You have to remember about
specified baud rate for communication.
If during installation you selected driver for Standard baud rates you would be able to use:
300 bps, 600 bps, 1200 bps, 2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps, 230400 bps,
460800 bps, 921600 bps.
If during installation you selected driver for Profibus baud rates you would be able to use:
300 bps, 600 bps, 1200 bps, 2400 bps, 4800 bps, 9600 bps,19200 bps, 9375 0bps ( if you select 230400bps),
187500 bps (if you select 460800bps ), 500000 bps ( if you select 921600bps ).
6. DRIVER UNINSTALLATION
6.1. DRIVER UNINSTALLATION IN WINDOWS 98/ME SYSTEMS
In this system driver uninstallation have to be done according follow steps:
a/ disconnect converter from computer,
b/ select menu Start > Setting > Control Panel > Add > Remove Programs,
c/ select from the list “ADA USB Serial Converter Driver” and press [Change / Remove],
e/ reboot the computer.
11
ADA-I9110
6.2. DRIVER UNINSTALLATION IN WINDOWS 2000/XP/2003/VISTA/7/2008 SYSTEMS
In this system driver uninstallation have to be done according follow steps:
a/ disconnect converter from computer,
b/ login as the Administrator,
c/ select menu Start > Setting > Control Panel > Add > Remove Programs,
d/ select from the list Windows Driver Package – CEL-MAR ADA – Virtual USB Serial Port,
e/ press [Change / Remove], Virtual USB Serial Port driver will be uninstalled,
f/ select from the list Windows Driver Package – CEL-MAR ADA – USB Serial Converter,
g/ press [Change / Remove], driver converter of USB Bus will be uninstalled,
h/ after uninstallation reboot the computer.
6.2.1. EXAMPLE DRIVER UNINSTALLATION IN WINDOWS 7 SYSTEMS
Windows 7 system driver uninstallation have to be done according follow steps:
a/ disconnect converter from computer,
b/ login the Administrator account ,
c/ select menu Start > Control Panel > Programs > Uninstall,
d/ select from Windows Driver Package – CEL-MAR ADA – Virtual USB Serial Port,
e/ press [Uninstall/Change], Virtual USB Serial Port driver will be uninstalled
f/ select from the list Windows Driver Package – CEL-MAR ADA – USB Serial Converter
g/ press [Uninstall/Change], driver converter of USB Bus will be uninstalled,
h/ after uninstallation reboot the computer.
12
ADA-I9110
6.3. EMERGENCY DRIVER UNINSTALLATION
If there are problems with correct operation of drivers or converter and or on computer was installed driver other devices this type, you
can use special software form delivered CD-ROM to clean the system form files and entries in the system registry.. This can be done
after uninstallation descried in point 6.1 and 6.2.
6.3.1. EMERGENCY DRIVER UNINSTALLATION IN WINDOWS 98/ME/2000
Emergency driver uninstallation in Windows 98/ME/2000 system have to be done according follow steps:
a/ disconnect converter from computer,
b/ from CD-ROM delivered with converter, copy to hard disk the folder Windows\Win-98ME_1.09.06\FTClean for Windows 98/ME or
Windows\Win-2000\FTClean for Windows 2000,
c/ from FTClean folder run the application FTClean.exe and follow the Tooltip,
d/ after finishing, reboot the computer.
6.3.2. EMERGENCY DRIVER UNINSTALLATION IN WINDOWS XP/2003/Vista/7/2008
Emergency driver uninstallation in Windows XP/2003/Vista/7/2008 system have to be done according follow steps:
a/ disconnect converter from computer,
b/ login the Administrator account,
c/ from CD-ROM delivered with converter, copy to hard disk the folder Windows\Win-XP-2003-Vista-7-2008_2.06\ CDMUninstaller,
d/ from CDMUninstaller folder run the application uninstall.bat,
e/ after finishing, reboot the computer.
7. USING
After property connection according to section above you can start using the converter. During the data transmission LEDs should
blink and they indicate appropriately:
LED
Description
PWR – green
Power ON
Tx – yellow
Transmitted Data form the ADA-I9110 via RS-232 port to the RS-232 Device.
Rx – red
Received Data from the RS-232 Device connected to RS232 converter port.
RTS – yellow
RTS (Request To Send) line condition of RS232 converter port.
CTS – red
CTS (Clear To Send) line condition of RS232 converter port.
DTR – yellow
DTR (Data Terminal Ready) line condition of RS232 converter port.
DSR – red
DSR (Data Set Ready) line condition of RS232 converter port.
DCD – red
DCD (Data Carrier Detect) line condition of RS232 converter port.
LED ON - status signal equal 1 logical
LED OFF - status signal equal 0 logical
7.1. BAUD RATE SELECTION FOR PROFIBUS COM PORT
For setting correct Profibus baud rate (after installation “Virtual Port” driver for Profibus) in application using virtual port COM follow
table below.
Set baud rate [bps]
Actual baud rate [bps]
Profibus
230400
937500
460800
187500
921600
500000
7.2. SELECTION OF COM PORT GREATER THEN COM9
If virtual port COM of converter will install in Windows OS as COM10 or greater then in application using this port you should type
COM port address as: \\.\COM10.
8. VERSIONS
ADA-I9110 Order example:
Product symbol : ADA-I9110-2
Galvanic isolation:
1kV=
1
3kV=
2
13
2 – galvanic isolation 1kV=.
ADA-I9110
9. RS232 INTERFACE – PIN DESCRIPTION OF D-SUB9-MALE SOCKET
Pin
DB-9
connector
SIGNAL
1
DCD
2
DESCRIPTION
ADA-I9110
Data Carrier Detect
Receiver
Rx
Transmitted Data
Receiver
3
Tx
Received Data
Transmitter
4
DTR
Data Terminal Ready
Transmitter
5
GND
Signal ground
GND
6
DSR
Data Set Ready
Receiver
7
RTS
Request To Send
Transmitter
8
CTS
Clear To Send
Receiver
9
RI
Ring Indicator
Receiver
10. SPECIFICATION
Parameters
USB
RS-232
Connector
USB connector type B
DSUB-9M (mail)
Line length
up to 5m
up to15 m
1
1
Maximum number of connected devices
Transmission line
Standards
Cable DB9F/DB9M multi-core 9x0,34 shielded (op
to 15m) or twisted cable 9-pairs UTP 9x2x0,5
Standard USB extension cable A-A
(24AWG) shield inside large interferences (STP
9x2x0,5 (24AWG)).
USB1.1, USB2.0
EIA-232, CCITT V.11
Maximum baud rate
up to 921,6 kbps (Standard) / up to 1500 kbps (Profibus)
Transmission type
Asynchronism half duplex or full duplex,
• PWD – green LED power supply,
• RX – red LED received data,
• TX – yellow LED transmitted data,
• additional signals: RTS, CTS, DTR, DSR, DCD, RI
Optical Signalization
Nominal work conditions
Power requirements
from USB of Computer
Power
Galvanic Isolation
< 0,5 W
Between RS232 signal line and USB on level 1kV= or 3kV=.
Operating temperature
0 ÷ +23 ÷ +50°C
5 ÷ 95% - non-condensing
Humidity
Location during work
Safety requiring
Free
Resistance to disruptions according to the standard PN-EN 55024.
Emission of disruptions according to the standard PN-EN 55022.
According to the PN-EN60950 norm.
Environment
Commercial and light industrial.
Electromagnetic compatibility
Casing
84 mm x 23 mm x 59 mm.
Dimensions (W x D x H)
Material
Polistyren
IP20
Degree of casing protection
Weight
0,05 kg
Conditions of storing and transportation
-40 ÷ 70°C
Storage temperature
Humidity
5 ÷ 95% - non-condensing
14
ADA-I9110
15
ADA-I9110
Dear Customer,
Thank you for purchasing CEL-MAR Company product.
We hope that the ADA-I9110 converter and this user manual help simplify your network of 1-Wire sensor for industrial applications.
We also wish to remind you that CEL-MAR Company are a manufacturer of the widest selections of data communications products
in the world in applications such as: data transmission converters in RS232, RS485, RS422, USB, Current Loop, Fibre-Optic and
Ethernet Converters and many others.
We welcome your feedback so please contact us to tell how you like our products and how we can satisfy you present and future
needs.
CEL-MAR sp.j.
Zakład Informatyki i Elektroniki
str. Ściegiennego 219C
25-116 Kielce, POLSKA
Tel.................................................... : +48 41 362-12-46
Tel/fax.............................................. : +48 41 361-07-70
Web................................................. : http://www.cel-mar.pl/en
Office................................................: [email protected]
Sales department ............................ : [email protected]
Technical information ..................... : [email protected]
16