Download 180W Moving Head Beam SI-056 User Manual

W Moving Head Beam
180
180W
6
SI-05
SI-056
User Manual
KEEP THIS MANUAL FOR FUTURE NEEDS
packing
1. Un
Unpacking
13. Maintenance and Cleaning
The following points have to be considered during the inspection:
Thank you for Color Imagination’s 180W Moving Head Beam. For your own safety, please read
1) All screws for installing the devices or parts of the device have to be tightly connected and must not
this manual before installing the device. This manual covers the important information on
be corroded.
installation and applications. Please install and operate the fixture with following instructions.
2) There must not be any deformations on the housing, color lenses, fixations and installation spots
Meanwhile, please keep this manual well for future needs.
(ceiling, suspension, trussing).
3）Mechanically moved parts must not show any traces of wearing and must not rotate with
Color Imagination’s 180W Moving Head Beam is made of a new type of high temperature
strength of engineering plastics and cast aluminum casing with nice outlook. The fixture is designed
unbalances.
4）The electric power supply cables must not show any damage, material fatigue or sediments.
and manufactured strictly following CE standards, complying with international standard DMX512
protocol. It’s available independently controlled and linkable with each other for operation. And it is
Further instructions depending on the installation spot and usage have to be adhered by a skilled
applicable for large-scale live performances, theater, studio, nightclubs and discos.
installer and any safety problems have to be removed.
SI-056 adopts powerful Osram SIRIUS HRI 180W lamp with revolutionary technology which
features high brightness and stability. Please carefully unpack it when you receive the fixture and
check whether it is damaged during the transportation. And please check whether the following
In order to make the lights in good condition and extend the life time, we suggest a regular cleaning to
items are included inside the box:
the lights.
1) Clean the inside and outside lens each week to avoid the weakneness of the lights due to
Moving Head---------one
Signal Cable----one
Omega Clamp-------Two
User Manual----one
Safety Chain---------One
accumulation of dust.
2) Clean the fan each week.
3) A detailed electric check by approved electrical engineer each three month, make sure that the
circuit contacts are in good condition,
prevent the poor contact of circuit from overheating.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use
alcohol or solvents.
There are no serviceable parts inside the device. Please refer to the instructions under “Installation
instructions”.
Should you need any spare parts, please order genuine parts from your local dealer.
11. Product Dimensions
2. Safety Instructions
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a
safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual.
12. Product Overviews
If the device has been exposed to temperature changes due to environmental changes, do not switch
it on immediately. The arising condensation could damage the device. Leave the device switched off
until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be earthed.
The electric connection must carry out by qualified person.
The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,
replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance with wall for
smooth air flow, so there should be no shelter for fans and ventilation for heat radiation.
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the
manufacturer or his service agent or a similar qualified person in order to avoid a hazard.
3. Operation Instructions
Other DMX modes available
-The moving head is for beam effect for onsite decoration purpose.
Customizable DMX channel assignment
-Don’t turn on the fixture if it’s been through severe temperature difference like after
DMX, stand-alone, master/slave, sound activated mode
transportation because it might damage the light due to the environment changes. So make sure
DMX recorder and edit function integrated
to operate the fixture until it is in normal temperature.
Software update
-This light should be keep away from strong shaking during any transportation or movement.
3-pin or 5-Pin XLR serial input/output
-Don’t pull up the light by only the head, or it might cause damages to the mechanical parts.
Fan cooling system
-Don’t expose the fixture in overheat, moisture or environment with too much dust when installing
Constant temperature readout / management function
it. And don’t lay any power cables on the floor. Or it might cause electronic shock to the people.
DB rating @ 1M = 54,18db
-Make sure the installation place is in good safety condition before installing the fixture.
2 x 1/4 turn fastening Omega Clamps
-Make sure to put the safety chain and check whether the screws are screwed properly when
Electronic ballast and power supply
installing the fixture.
-Make sure the lens are in good condition. It’s recommended to replace the units if there are any
10. Technical Specifications
damages or severe scratch.
-Make sure the fixture is operated by qualified personnel who knows the fixture before using.
Input Voltage: AC 100V ~ 240V 50/60Hz
-Keep the original packages if any second shipment is needed.
Light Source: 1* Osram SIRIUS HRI 180W lamp
-Don’t try to change the fixtures without any instruction by the manufacturer or the appointed
Control Signal: DMX512, master-slave and sound activated or auto operation
repairing agencies.
Control Channel: 14 DMX Channels
-It is not in warranty range if there are any malfunctions from not following the user manual to
Power Consumption: 342W
operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
Dimensions: 315x359x514mm
Packing Dimensions: 620*430*415mm
4. Mounting and Installation
Net Weight: 15kg
Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas,
Gross Weight: 18kg
or in areas were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
9. Key Features
from a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at
2000 hour rated lamp source
least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).
Osram SIRIUS HRI 180W lamp (8400lumen, 7500°K, 2000h) included
Always use and install the supplied safety cable as a safety measure to prevent accidental damage
59320 Lux @ 2,5m
and/or injury in the event the clamp fails.
2,5° beam angle
Mounting points
points:: Overhead mounting requires extensive experience, including amongst others
No need for adjustment of reflector or lamp
calculating working load limits, a fine knowledge of the installation material being used, and
Anti-reflection lenses
periodic safety inspection of all installation material and the fixture. If you lack these qualifications,
1 color wheel with total 13 colors plus open
do not attempt the installation yourself. Improper installation can result in bodily injury.
Variable direction rainbow effect with speed adjustable
Be sure to complete all rigging and installation procedures before connecting the main power
1 rotatable gobo wheels with 12 rotatable, indexable and interchangeable gobos plus open
cord to the appropriate wall outlet.
Variable speed gobo scrolling in both directions
Clamp Mounting
Mounting:: The Beam provides two unique mounting bracket assemblys that integrates
12.0mm outside, 8mm image diameter (Gobo Size)
the bottom of the base, the included “Omega Bracket,” and the safety cable rigging point in one
1 rotatable and indexable 8-facet prism with speed adjustable and variable direction
unit (see the illustration below). When mounting this fixture to truss be sure to secure an
Macro-function for rotatable gobo/prism combinations
appropriately rated clamp to the included omega bracket using a M10 screw fitted through the
Variable Frost Filter (Hybrid effect for Wash)
center hole of the “omega bracket”. As an added safety measure be sure to attached at least one
Dual flag mechanical dimming system
properly rated safety cable to the fixture using on of the safety cable rigging point integrated in
Variable speed strobe effect
the base assembly.
Preset variable/random strobe and dimming pulse effects
Motor driven focus from near to far
540°/630° PAN and 265° TILT movement
Automatic Pan / Tilt position correction
16 bit smooth and precise resolution for PAN/TILT movement
Motors for fast and accurate Pan / Tilt positioning
Vector Mode with blackout MIB function
Blue LCD Display
14 DMX channels USITT DMX-512 (16-bit resolution)
Regardless of the rigging option you choose for your BEAM, always be sure to secure your fixture with a
224-255
safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging bracket as
Shutter open
illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a
9
7
2
Dimmer
0-255
0-100% Linear dimmer
safety cable to a carrying handle.
10
8
6
Focus
0-255
In(near) to out(far)
Rrotating
0-005
OFF
prism,
006-127
ON
Prism,
128-189
Forwards rotation from fast to slow
male 3-pin XLR input of the moving head. You can chain multiple moving head together through serial
Gobo
190-193
Prism rotation stop
linking. The cable needed should be two core, screened cable with XLR input and output connectors.
macros
194-255
Backwards rotation from slow to fast
5. DMX-512 control connections
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other side to the
Please refer to the diagram below.
11
12
9
10
7
8
0-099
Frost off
100-255
Frost on
Frost
DMX-512 connection with DMX terminator
0-225
13
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment,
such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption
of the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120 Ω
resistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the last
fixture in the chain. Please see illustrations below.
120
120Ω
2
3
1
PIN 3
PIN 2
14
11
12
Max to min speed
Speed
226-235
Blackout by movement
Pan/Tilt
236-245
Blackout by all wheel changing
246-255
No function
0-019
No function
020-029
No function
030-039
No function
040-059
Lamp on
060-079
Lamp switch off
080-099
Motor reset
100-119
Internal program 1
120-139
Internal program 2
140-159
Internal program 3
160-179
Internal program 4
180-199
Internal program 5
200-219
Internal program 6
220-239
Internal program 7
240-255
Internal program 8
11
12
Special
6
4
4
048-055
Gobo 6
6. Menu Operations
056-063
Gobo 7
Function Mode
064-071
Gobo 8
Set to slave
072-079
Gobo 9
Auto Run
Internal Program1~8
Master/Alone
080-087
Gobo 10
Music Control
Internal Program1~8
Master/Alone
088-095
Gobo 11
Reset
On/Off
096-103
Gobo 12
Reverse Pan
On/Off
104-111
Gobo 1 shake from slow to fast
Reverse Tilt
On/Off
112-119
Gobo 2 shake from slow to fast
Mic sensitivity
0~99%
120-127
Gobo 3 shake from slow to fast
Special
Reset Default
On/Off
128-135
Gobo 4 shake from slow to fast
Calibration
Code（Password：088）
136-143
Gobo 5 shake from slow to fast
144-151
Gobo 6 shake from slow to fast
152-159
Gobo 7 shake from slow to fast
160-167
Gobo 8 shake from slow to fast
168-175
Gobo 9 shake from slow to fast
176-183
Gobo 10 shake from slow to fast
184-191
Gobo 11 shake from slow to fast
192-199
Gobo 12 shake from slow to fast
200-255
Rot. gobo wheel cont. rotation from slow to fast
Gobo 1
0-003
7
5
6
Sensitivity of mic
PAN, TILT, Color Wheel, Gobo Wheel
1, Gobo Wheel 2, Focus
Temperature
XXX℃/℉
Manual Control
Lamp
On/Off
Channel
PAN=XXX……
Signal Set
Wire DMX
Wireless DMX
Act WDMX & Out
Program1
Steps(1..48)
…
Scenes 01
Pan=XXX…
Program8
…
…
Scenes XX
Time=xx.xS
Gobo 1
004-127
Forwards gobo rotation from fast to slow
rotation
128-131
Gobo rotation stop
132-255
Backwards gobo rotation from slow to fast
Edit Program
5
1
A001~AXXX
Gobo rotation stop
Mode of channel
Mode Set
16Bit Mode
0-031
Shutter closed
032-063
Shutter open
064-095
Strobe effect slow to fast
Design
Max Channel = XX
096-127
Shutter open
Mode Set
PAN = 001
128-159
Pulse strobe effect in sequences from slow to fast
160-191
Shutter open
192-223
Random strobe effect from slow to fast
Shutter,
8
DMX Address
Strobe
8Bit Mode
Design Mode
…
Information
Lamp Hours
XXXX(Hours)
8.DMX Channels
Clear
On/Off
Mode/Channel
Lamp
Time
Software
Version
V1.0~V9.9
Function
16B
8B
DE
1
1
9
2
3
2
10
4
3
3
Description
Pan
0-255
PAN Movement
Pan Fine
0-255
Fine control of Pan movement
Tilt
0-255
Tilt Movement
Tilt Fine
0-255
Fine control of Tilt movement
0-008
Open/White
7. Photometric Data
5
Values
Color
009-017
Color 1
018-026
Color 2
027-035
Color 3
036-044
Color 4
045-052
Color 5
053-061
Color 6
062-070
Color 7
071-079
Color 8
080-088
Color 9
089-096
Color 10
097-105
Color 11
106-114
Color 12
115-127
Color 13
128-189
Forwards rainbow effect from fast to slow
190-193
Color rotation stop
194-255
Backwards rainbow effect from slow to fast
0-007
Open
008-015
Gobo 1
016-023
Gobo 2
024-031
Gobo 3
032-039
Gobo 4
040-047
Gobo 5