Download SERVICE MANUAL - Wiki Karat

CDX-T67
SERVICE MANUAL
US Model
Canadian Model
AEP Model
UK Model
E Model
Ver 1.4 2002.07
Model Name Using Similar Mechanism
NEW
CD Drive Mechanism Type
MG-276A-159
Optical Pick-up Name
KSS-720A
SPECIFICATIONS
System
Compact disc digital audio system
Frequency response
10 – 20,000 Hz
Wow and flutter
Below the measurable limit
Signal-to-noise ratio
93 dB
Outputs
BUS control output (8 pins)
Analog audio output (RCA pin)
Current drain
800 mA (during CD playback)
800 mA (during loading or ejecting a
disc)
Operating temperature
–10°C to +55°C
Dimensions
Approx. 234.4 × 60 × 159.5 mm (w/h/d)
not incl. projecting parts and controls
Mass
Approx. 1.5 kg
Power requirement
12 V DC car battery (negative earth)
Supplied accessories
Disc magazine (1)
Parts for installation and connections
(1 set)
Design and specifications subject to change without notice.
COMPACT DISC CHANGER
9-870-272-15
Sony Corporation
2002G0500-1
C 2002.07
e Vehicle Company
Published by Sony Engineering Corporation
CDX-T67
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICKUP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
DISC MAGAZINE GETTING OUT PROCEDURE
ON THE POWER SUPPLY IS OFF
Remove the CASE (LOWER. S) beforehand
1) Press the lever (MZ LOCK) in the direction of arrow A.
2) Removal the magazine assy.
Note: Take out the magazine only when the tray is completely within the
magazine. If the disk or tray is sticking out, turn on the power and
eject the magazine.
Lever (MZ LOCK)
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
A
US/Canadian model:
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
OPTICAL
PICK-UP
BLOCK
Magazine assy
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
SEMI-FIXED
RESISTOR
AEP/UK model:
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
When replacing the chassis (U.S) sub assy of mechanism deck
which have the “CAUTION LABEL” attached, please be sure to
put a new CAUTION LABEL (3-223-913-11) to the chassis (U.S)
sub assy.
2
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0
SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE
DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ
DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES
NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
CDX-T67
SECTION 1
GENERAL
TABLE OF CONTENTS
Inserting a disc
SERVICING NOTES .......................................................... 2
1.
This section is extracted from
instruction manual.
Insertion d un disque
1
Einlegen von CDs
Labeled surface up
Etiquette vers le haut
Mit der beschrifteten Seite nach oben
Etiket naar boven
Con l’etichetta rivolta verso l’alto
With the arrow side facing up
Avec la partie fléchée tournée vers le haut
Mit dem Pfeil nach oben
Met het pijltje naar boven
Con il lato della freccia rivolto verso l’alto
Use the supplied disc magazine or the disc magazine XA-T7.
The disc magazine XA-T6 can not be used with this unit. If you
use any other magazine, it may cause a malfunction.
Een disc inbrengen
2
Installation ....................................................................... 4
Connections ..................................................................... 4
c
Tab
Languette
Lasche
Lipje
Linguetta
Verwenden Sie das mitgelieferte CD-Magazin oder das CDMagazin XA-T7. Das CD-Magazin XA-T6 kann nicht zusammen
mit diesem Gerät eingesetzt werden. Wird ein anderes als das
empfohlene CD-Magazin verwendet, kann es zu
Fehlfunktionen kommen.
6 discs, one in each tray
6 disques, un par plateau
Insgesamt 6 CDs (eine in jedem Fach)
6 discs, één per lade
6 dischi, uno in ciascun comparto
Slide open
Coulissez pour ouvrir
Öffnen
Openschuiven
Aprire facendo scorrere lo sportello
Push the label printed “PUSH” to unlock the door.
Appuyez sur l’étiquette portant l’inscription “PUSH”
pour déverrouiller la porte.
Drücken Sie auf die mit „PUSH“ gekennzeichnete
Stelle, um den Deckel zu entriegeln.
Druk op het label met de vermelding “PUSH” om de
klep te ontgrendelen.
Per sbloccare il coperchio, premere in corrispondenza
della dicitura “Push”.
Utilisez le magasin à disques fourni ou un magasin à disques
XA-T7. Vous ne pouvez pas utiliser de magasin à disques
XA-T6 avec cet appareil. L’utilisation d’un autre type de
magasin à disques risque de provoquer un dysfonctionnement.
GENERAL
Inserimento di un disco
c
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
2-8.
2-9.
2-10.
2-11.
2-12.
2-13.
2-14.
2-15.
Disassembly Flow ...........................................................
Front Panel (S) Assy, Case (Upper S) ............................
Mechanism Deck (MG-276A-159) ................................
Jack Board .......................................................................
Belt (TS) ..........................................................................
Main Board ......................................................................
Escutcheon (S), Slide Variable Resistor
(Elevator Height Sensor) (RV301) .................................
MD Motor Assy (Elevator) (M104) ................................
LE Motor Assy (Chucking) (M103) ...............................
RF Board .........................................................................
Sled Motor Complete Assy (M101) ...............................
Optical Pick-up (KSS-720A) ..........................................
Chassis (EV) Assy ...........................................................
Lever (CHK.L) Assy, Lever (CHK.R) Assy ...................
Chassis (OP) Block Service Assy ...................................
3.
MECHANICAL ADJUSTMENT .......................... 13
Notes on the disc magazine
Remarques sur le chargeur de disques
Hinweise zum CD-Magazin
Opmerkingen betreffende het disc-magazijn
Note sul contenitore dischi
4.
ELECTRICAL CHECK .......................................... 14
• Do not leave the disc magazine in locations with high temperatures and high
humidity such as on a car dashboard or in the rear window where the disc
magazine will be subjected to direct sunlight.
• Do not place more than one disc at a time onto one tray, otherwise the
changer and the discs may be damaged.
• Do not drop the disc magazine or subject it to a violent shock.
• Ne pas laisser le chargeur de disques dans un endroit très chaud ou très
humide comme sur le tableau de bord ou sur la plage arrière d’une voiture
où il serait en plein soleil.
• Ne pas insérer plus d’un disque à la fois sur le plateau, sinon le changeur et
les disques risquent d’être endommagés.
• Ne pas laisser tomber le chargeur de disques ni le cogner.
• Halten Sie das Magazin von hohen Temperaturen und Feuchtigkeit fern.
Lassen Sie es nicht auf dem Armaturenbrett, auf der Heckablage usw. liegen,
wo es direktem Sonnenlicht ausgesetzt ist.
• Versuchen Sie nicht, mehr als eine CD in ein Fach einzulegen. Andernfalls
können der Wechsler und die CDs beschädigt werden.
• Lassen Sie das Magazin nicht fallen, und schützen Sie es vor Stößen.
• Laat het magazijn niet achter op plaatsen waar dit blootgesteld wordt aan
vocht of aan hoge temperaturen, zoals op het dashboard van een auto of op
de hoedenplank, waar het magazijn in de volle zon staat.
• Steek niet meer dan één enkele disc in een uitsparing, anders kunnen zowel
de CD-wisselaar als de compact discs beschadigd worden.
• Laat het apparaat niet vallen en stel het niet bloot aan hevige trillingen of
schokken.
• Non lasciare il contenitore dischi in luoghi con temperature elevate o molto
umidi, come sul cruscotto o sul ripiano posteriore di un’auto dove il
contenitore potrebbe essere esposto alla luce solare diretta.
• Non inserire più di un disco alla volta in ciascun comparto, diversamente il
cambia CD e i dischi saranno danneggiati.
• Non lasciar cadere il contenitore dischi e non sottoporlo a urti violenti.
5.
DIAGRAMS
5-1. Block Diagram – SERVO Section – ..............................
5-2. Block Diagram – BUS CONTROL/
POWER SUPPLY Section – ...........................................
5-3. Note for Printed Wiring Boards and
Schematic Diagrams .......................................................
5-4. Printed Wiring Boards – RF Board – ............................
5-5. Schematic Diagram – RF Board – .................................
5-6. Printed Wiring Boards
– MAIN Board (Component Side) – ..............................
5-7. Printed Wiring Board
– MAIN Board (Conductor Side) – ................................
5-8. Schematic Diagram – MAIN Board (1/2) – ..................
5-9. Schematic Diagram – MAIN Board (2/2) – ..................
5-10. Printed Wiring Boards – JACK Board – ........................
5-11. Schematic Diagram – JACK Board – .............................
5-12. IC Pin Function Description ...........................................
6.
Note
5
6
6
7
7
8
You cannot play an 8cm CD on this unit.
If you use the single adaptor, it may cause a malfunction.
Remarque
Il est impossible de lire un CD de 8 cm sur cet appareil.
Si vous utilisez l’adaptateur unique, il peut provoquer un
dysfonctionnement.
Hinweis
Mit diesem Gerät können Sie keine Single-CDs (8-cm-CDs)
wiedergeben lassen.
Wenn Sie einen Single-CD-Adapter verwenden, kann es zu
Fehlfunktionen kommen.
3
8
9
9
10
10
11
11
12
12
U kunt geen 8 cm CD afspelen met dit toestel.
Door gebruik te maken van een single adapter kan het
toestel defect raken.
Nota
Con il presente apparecchio, non è possibile riprodurre CD
da 8cm.
Se viene utilizzato l’adattatore singolo, è possibile che si
verifichino problemi di funzionamento.
23
24
25
26
26
30
EXPLODED VIEWS
Hinweis
Um Verletzungen zu vermeiden, greifen Sie mit der Hand nicht in den CDWechsler.
4
Push Z (EJECT) button down
Appuyez sur la touche Z (EJECT)
Drücken Sie die Taste Z (EJECT) nach unten.
Druk de Z (EJECT) knop in.
Premere il tasto Z (EJECT).
Note
When a disc magazine is inserted into the CD changer or the reset
button of the connected car audio is pressed, the unit will
automatically be activated and read the information on the CDs.
When the information on all the CDs in the disc magazine has been
read, the unit will automatically stop operation.
Opmerking
Steek uw hand niet in de CD-wisselaar om verwondingen te voorkomen.
Nota
Per evitare danni alla persona, non inserire le mani nel cambia CD.
Utilisez cet appareil avec la fenêtre complètement fermée
Sinon, des corps étrangers pourraient pénétrer dans l’appareil et
encrasser les lentilles dans le lecteur.
Gebruik het toestel met volledig gesloten klep
Anders zou er stof of vuil in het apparaat terecht kunnen komen,
met als gevolg vervuilde lenzen en storingen in de werking.
Remarque
Quand un chargeur de disques est inséré dans le changeur de CD ou
si la touche de réinitialisation de l’autoradio raccordé est
enclenchée, l’appareil se met automatiquement en marche et
reproduit les CD. Lorsque tous les CD du chargeur ont été
reproduits, l’appareil s’arrête automatiquement.
Opmerking
Wanneer een disc-magazijn in de compact disc-wisselaar wordt
geplaatst of de terugsteltoets van de uitleesvenster-eenheid wordt
ingedrukt, zal het apparaat automatisch ingeschakeld worden,
waarna de informatie van de compact discs gelezen wordt. Nadat
alle informatie gelezen is, zal het apparaat weer automatisch in de
stopstand komen te staan.
Verwenden Sie das Gerät nur mit vollständig geschlossener
Klappe
Halten Sie die Klappe des Geräts stets geschlossen, damit keine
Fremdkörper eindringen und die Linsen im Wechsler nicht
verschmutzen können.
Hinweis
Wenn Sie ein CD-Magazin in den CD-Wechsler einsetzen oder die
Rücksetztaste an der angeschlossenen Audio-Anlage in Ihrem Auto
drücken, schaltet sich das Gerät automatisch ein und beginnt, die
Daten auf den CDs zu lesen. Nachdem die Informationen auf allen
CDs im CD-Wechsler gelesen wurden, stoppt das Gerät automatisch.
Utilizzare l’apparecchio con lo sportello chiuso
Diversamente oggetti estranei potrebbero penetrare
nell’apparecchio e contaminare le lenti all’interno del cambia CD.
Nota
Quando un contenitore dischi è inserito nel cambia CD o viene
premuto il pulsante di azzeramento dell’autostereo collegato,
l’apparecchio si accende automaticamente e legge le informazioni
dei dischi. Quando le informazioni di tutti i dischi inseriti nel
contenitore dischi sono state lette, l’apparecchio si ferma
automaticamente .
When the tray comes out
Lorsque le plateau sort
Wenn sich ein Fach gel st hat
Als de houder uitsteekt
Quando il comparto fuoriesce
Normally, the trays will not come out of the magazine. However, if
they are pulled out of the magazine, it is easy to re-insert them.
En principe, les plateaux ne sortent pas du chargeur. Toutefois, s’ils
sortent du chargeur, il est facile de les réinsérer.
Normaal gezien steken de houders niet uit het magazijn. Als ze er toch
zouden zijn uitgetrokken, kan u ze er makkelijk weer insteken.
Di solito, i comparti non fuoriescono dal contenitore; se ciò dovesse
avvenire, è facile reinserirli.
With the cut-away portion of the tray facing you, insert the right
corner of the tray in the slot, then push in the left corner until it
clicks.
Avec la portion découpée du plateau vous faisant face, insérer le
coin droit du plateau dans la fente, puis enfoncer le coin gauche
jusqu’au déclic.
Normalerweise können sich die Fächer nicht vom Magazin lösen.
Werden sie jedoch aus dem Magazin herausgezogen, lassen sie sich
mühelos wieder anbringen.
Met de uitsparing in de houder naar u toe gericht, brengt u de
rechterhoek van de houder in de gleuf en drukt dan de linkerhoek
erin tot u een klik hoort.
Con la parte del comparto tagliata rivolta in avanti, inserire
l’angolo destro del comparto nell’alloggiamento, quindi inserire
l’angolo sinistro fino a farlo scattare in posizione.
Note
Do not insert the tray upside down or in the wrong direction.
Remarque
Ne pas insérer le plateau à l’envers ou dans le mauvais sens.
Opmerking
De houder niet omgekeerd of in de verkeerde richting inbrengen.
Nota
Non inserire il vassoio capovolto o nella direzione errata.
Hierbei muß die Aussparung des Fachs auf Sie weisen. Setzen Sie
dann die rechte Ecke des Fachs in den Einschub ein, und drücken
Sie danach die linke Ecke an, bis das Fach mit einem Klicken
einrastet.
Hinweis
Versuchen Sie nicht, das Fach mit der falschen Seite nach oben oder
verkehrt herum einzusetzen.
Notes on handling discs
Remarques sur la manipulation des disques
Hinweise zum Umgang mit CDs
Opmerkingen bij het omgaan met discs
Note sulla manipolazione dei dischi
A dirty or defective disc may cause sound drop-outs during playback. To
enjoy optimum sound, handle the disc as follows.
• Handle the disc by its edge, and to keep the disc clean, do not touch the
unlabeled surface. (fig. A)
• Do not stick paper or tape on the disc. (fig. B)
• Keep your discs in their cases or disc magazines when not in use.
Do not expose discs to direct sunlight or heat sources such as hot airducts. Do not leave discs in a car parked in direct sunlight where there
can be a considerable rise in the temperature inside the car. (fig. C)
• Before playing, clean the discs with a commercially available cleaning
cloth. Wipe each disc from the centre out. (fig. D)
Do not use solvents such as benzine, thinner, commercially available
cleaners, or antistatic spray intended for analog discs.
• Discs with non-standard shapes (e.g., heart, square, star) cannot be
played on this unit. Attempting to do so may damage the unit. Do not
use such discs.
• You cannot play 8cm CDs.
Un disque sale ou défectueux peut provoquer des pertes de son à la lecture.
Manipuler le disque comme suit pour obtenir un son optimal.
• Manipuler le disque par son arête et le maintenir dans un état propre,
ne pas le toucher sur la surface non imprimée. (fig. A)
• Ne pas coller de papier ou de bande adhésive sur le disque. (fig. B)
• Conservez vos disques dans leurs boîtiers ou des pochettes de
rangement lorsqu’ils ne sont pas utilisés.
Ne pas laisser les disques en plein soleil ou près d’une source de chaleur
comme des conduits d’air chaud. Ne pas laisser les disques dans une
voiture garée en plein soleil car la température de l’habitacle risque
d’augmenter considérablement. (fig. C)
• Avant la lecture, nettoyez les disques avec un chiffon de nettoyage
disponible dans le commerce. Essuyez chaque disque en partant du
centre vers l’extérieur. (fig. D)
N’utilisez pas de solvants tels que la benzine, du diluant, des produits de
nettoyage vendus dans le commerce ou des sprays antistatiques destinés aux
disques analogiques.
• Les disques de formes non standard (par exemple en forme de cœur, de
carré ou d’étoile) ne peuvent pas être lus sur cet appareil. Vous risquez
d’endommager votre appareil si vous essayez de le faire. N’utilisez pas
de tels disques.
• La lecture de CD de 8 cm n’est pas possible.
Eine verschmutzte oder beschädigte CD kann Tonaussetzer verursachen. Um
optimale Klangqualität sicherzustellen, beachten Sie folgendes:
• Damit die CD sauber bleibt, fassen Sie sie immer am Rand an, und
berühren Sie nicht die Seite ohne Beschriftung. (Abb. A)
• Kleben Sie weder Papier noch Klebeband auf die CD. (Abb. B)
• Bewahren Sie CDs in ihrer Hülle oder in den CD-Magazinen auf, wenn
sie nicht abgespielt werden.
Schützen Sie die CD vor Sonnenlicht und Wärmequellen wie
Warmluftauslässen. Lassen Sie sie nicht in einem Auto liegen, das direkt
in der Sonne geparkt ist, da die Temperatur im Wageninneren sehr hoch
ansteigen kann. (Abb. C)
• Reinigen Sie die CDs vor dem Abspielen mit einem handelsüblichen
Reinigungstuch. Wischen Sie dabei von der Mitte nach außen. (Abb. D)
Verwenden Sie keine Lösungsmittel wie Benzin oder Verdünner und keine
handelsüblichen Reinigungsmittel oder Antistatik-Sprays für Schallplatten.
• CDs mit ungewöhnlichen Formen, zum Beispiel herz- oder sternförmige
oder quadratische CDs, können Sie mit diesem Gerät nicht abspielen.
Falls Sie es doch versuchen, kann das Gerät beschädigt werden.
Verwenden Sie solche CDs nicht.
• Single-CDs (8-cm-CDs) können nicht wiedergegeben werden.
Bij het afspelen van een vuile of beschadigde disc kan het geluid regelmatig
wegvallen. Voor het verzekeren van een goede geluidsweergave dient u als
volgt met discs om te gaan.
• Pak een compact disc altijd bij de rand vast, houd hem proper en raak
het oppervlak (behalve het label) niet aan. (afb. A)
• Plak geen papier of plakband op een compact disc. (afb. B)
• Bewaar uw discs in hun doosje of disc-magazijn wanneer u ze niet
gebruikt.
Stel compact discs niet bloot aan direkt zonlicht of warmeluchtkanalen.
Laat ze niet liggen in een geparkeerde auto in de volle zon, aangezien
de temperatuur hierin bijzonder hoog kan oplopen. (afb. C)
• Maak een disc voor het afspelen altijd schoon met een in de handel
verkrijgbare doek. Wrijf van binnen naar buiten toe. (afb. D)
Gebruik geen solventen zoals benzine, thinner en in de handel verkrijgbare
reinigingsmiddelen of antistatische sprays voor grammofoonplaten.
• Discs met afwijkende vormen (b.v. hart, vierkant, ster) kunnen niet met
deze dit toestel worden afgespeeld. Indien u dat toch doet, kan het
toestel worden beschadigd. Gebruik geen dergelijke discs.
• U kunt geen 8cm CD’s afspelen.
Un disco sporco o difettoso può causare cadute di suono durante la
riproduzione. Per poter ascoltare un suono ottimale, trattare i dischi come
indicato.
• Prendere i dischi per il bordo e, per tenerli puliti, non toccare la
superficie senza etichetta. (fig. A)
• Non attaccare carta o nastro adesivo sul disco. (fig. B)
• Quando non vengono utilizzati, conservare i dischi nelle apposite
custodie.
Non esporre i dischi alla luce solare diretta o a fonti di calore come
condotti di aria calda. Non lasciarli in veicoli parcheggiati al sole dove
può verificarsi un considerevole aumento della temperatura. (fig. C)
• Prima della riproduzione, pulire i CD con un panno di pulizia disponibile
in commercio. Pulire ogni CD dal centro verso l’esterno. (fig. D)
Non utilizzare solventi quali benzene, acquaragia o detersivi reperibili in
commercio, né spray antistatici per dischi analogici.
• Non è possibile riprodurre CD con forme irregolari (ad esempio a forma
di cuore, di quadrato, di stella) su questo lettore. Non utilizzare tali
dischi onde evitare di danneggiare il lettore.
• Non è possibile riprodurre CD da 8 cm.
Hinweise zu CDs
Opmerkingen bij discs
Note sui dischi
Indien u de discs behandelt zoals hieronder beschreven, kunnen kleverige
resten de disc doen stoppen waardoor het toestel defect of uw discs
beschadigd kunnen raken.
Gebruik geen gebruikte of gehuurde CD’s met kleverig oppervlak
(bijvoorbeeld afkomstig van stickers of inkt of lijm die van onder de stickers
komt).
• Lijmresten. Kleverige inkt. (afb. E)
Gebruik geen gehuurde CD’s met oude labels die loskomen.
• Stickers die loskomen laten kleverige resten achter. (afb. F)
Gebruik geen discs waarop stickers zijn gekleefd.
• Vastgekleefde labels. (afb. G)
I residui di colla presenti sui dischi indicati di seguito potrebbero causare
l’arresto del disco stesso e problemi di funzionamento dell’apparecchio o
danneggiare i dischi stessi.
Non utilizzare dischi di seconda mano o presi a noleggio che presentano
residui di colla sulla superficie, ad esempio residui di etichette o inchiostro
rimossi oppure residui di colla che fuoriescono dalle etichette.
• Residui di colla. Residui di inchiostro. (fig. E)
Non utilizzare dischi presi a noleggio con etichette vecchie che cominciano a
staccarsi.
• Etichette che cominciano a staccarsi, lasciando residui di colla. (fig. F)
Non utilizzare dischi su cui siano applicati etichette o adesivi.
• Etichette applicate. (fig. G)
Notes on discs
If you use the discs explained below, the sticky residue can cause the disc to
stop spinning and may cause malfunction or ruin your discs.
Do not use second-hand or rental CDs that have a sticky residue on the surface
(for example from peeled-off stickers or from ink, or glue leaking from under
the stickers).
• There are paste residue. Ink is sticky. (fig. E)
Do not use rental CDs with old labels that are beginning to peel off.
• Stickers that are beginning to peel away, leaving a sticky residue.
(fig. F)
Do not use your discs with labels or stickers attached.
• Labels are attached. (fig. G)
Remarques sur les disques
• You can play CD-Rs (recordable CDs) designed for audio use on this
unit. (fig. H)
• Some CD-Rs (depending on the equipment used for its recording or the
condition of the disc) may not play on this unit.
• You cannot play a CD-R that is not finalized*.
• You cannot play CD-RWs (rewritable CDs) on this unit.
Si vous utilisez les disques décrits ci-dessous, le résidu adhésif risque de
provoquer l’arrêt de la rotation du disque et d’entraîner un
dysfonctionnement ou d’endommager vos disques.
N’utilisez pas de CD de seconde main ou de location qui présentent des
résidus adhésifs à la surface (par exemple d’étiquettes décollées ou d’encre, de
colle dépassant de l’étiquette).
• Résidus de colle. L’encre colle. (fig. E)
N’utilisez pas de CD de location avec d’anciennes étiquettes qui
commencent à se décoller.
• Les étiquettes qui commencent à se décoller laissent des résidus
adhésifs. (fig. F)
N’utilisez pas vos disques avec des étiquettes ou des autocollants apposés
dessus.
• Les étiquettes sont fixées. (fig. G)
* A process necessary for a recorded CD-R disc to be played on the audio CD
player.
Remarques sur les disques CD-R/CD-RW
Notes on CD-R/CD-RW discs
ELECTRICAL PARTS LIST ............................... 36
Remarque
Pour éviter toute blessure, ne pas introduire la main dans le changeur de CD.
Use the unit with the door closed completely
Otherwise, foreign matter may enter the unit and contaminate the
lenses inside the changer.
19
20
21
22
Note
To prevent injury, do not insert your hand in the CD changer.
Utilizzare il contenitore dischi in dotazione o il contenitore
dischi XA-T7. Il contenitore dischi XA-T6 non può essere
utilizzato con questo apparecchio. Se si utilizza qualsiasi altro
contenitore, potrebbero sorgere problemi di funzionamento.
To remove
Retrait
Herausnehmen des CD-Magazins
Verwijderen
Per estrarre
If the disc magazine does not lock properly
Take out the magazine, and after pressing the Z (EJECT) button, reinsert it.
Si vous ne pouvez pas fermer le chargeur de disques
Sortez le chargeur et, après avoir appuyé sur la touche Z (EJECT), réinsérez-le.
Wenn sich das CD-Magazin nicht richtig verriegeln läßt
Nehmen Sie das Magazin heraus, drücken Sie die Z (EJECT)-Taste, und setzen Sie das Magazin dann wieder ein.
Als het disc-magazijn niet soepel op zijn plaats vastklikt
Verwijder het disc-magazijn, druk op de Z (EJECT) toets en breng vervolgens het disc-magazijn opnieuw in.
Se il contenitore dischi non si blocca in posizione correttamente
Estrarlo e, dopo aver premuto il tasto Z (EJECT), reinserirlo.
18
6-1. Case Section .................................................................... 33
6-2. Mechanism Deck Section-1 (MG-276A-159) ................ 34
6-3. Mechanism Deck Section-2 (MG-276A-159) ................ 35
7.
Opmerking
Disc magazine
Chargeur de disques
CD-Magazin
Disc-magazijn
Contenitore dischi
17
Gebruik het meegeleverde disc-magazijn of het disc-magazijn
XA-T7. Het disc-magazijn XA-T6 kan niet met dit toestel
worden gebruikt. Het gebruik van een ander magazijn kan
defecten veroorzaken.
A
Hinweise zu CD-Rs/CD-RWs
• Vous pouvez écouter avec cet appareil des CD-R (CD enregistrables)
conçus pour une utilisation audio. (fig. H)
• Certains CD-R (en fonction des conditions de l’équipement
d’enregistrement ou du disque) risquent de ne pas être lus avec cet
appareil.
• Vous ne pouvez pas lire de disques CD-R non finalisés*.
• Vous ne pouvez pas lire de CD-RW (CD réinscriptibles) avec cet appareil.
• Mit diesem Gerät können Sie CD-Rs (beschreibbare CDs) wiedergeben
lassen, die für den Einsatz als Tondatenträger konzipiert sind. (Abb. H)
• Je nach dem Aufnahmegerät, mit dem die CD-R bespielt wurde, oder
dem Zustand der CD-R selbst können einige CD-Rs mit diesem Gerät
möglicherweise nicht wiedergegeben werden.
• Eine noch nicht abgeschlossene CD-R kann nicht wiedergegeben
werden*.
• Eine CD-RW (wiederbeschreibbare CD) kann mit diesem Gerät nicht
wiedergegeben werden.
* Un processus nécessaire à la lecture des disques CD-R enregistrés sur le lecteur
de CD audio.
* Damit eine bespielte CD-R auf einem Audio-CD-Player wiedergegeben werden
kann, ist ein spezieller Prozeß erforderlich.
B
This way
Oui
Richtig
Juist
Cosi
Wenn Sie die unten aufgeführten CDs verwenden, können
Klebstoffrückstände dazu führen, daß die CD sich nicht mehr dreht, oder
Fehlfunktionen oder Schäden an der CD verursachen.
Verwenden Sie keine gebraucht gekauften oder Leih-CDs mit klebrigen
Rückständen auf der Oberfläche (z. B. von abgelösten Aufklebern, von Tinte
oder von Klebstoff, der unter den Aufklebern hervorquillt).
• Klebstoffrückstände. Tinte klebt. (Abb. E)
Verwenden Sie keine Leih-CDs mit alten Etiketten, die sich abzulösen
beginnen.
• Aufkleber, die sich zu lösen beginnen und Klebstoffrückstände
hinterlassen. (Abb. F)
Verwenden Sie keine CDs, an denen Etiketten oder Aufkleber angebracht
sind.
• Angebrachte Etiketten. (Abb. G)
C
D
This way
Oui
Richtig
Juist
Cosi
Not this way
Non
Falsch
Fout
Non cosi
Not this way
Non
Falsch
Fout
Non cosi
3
E
3
F
Opmerkingen bij CD-R/CD-RW discs
• Audio CD-R’s (opneembare CD’s) kunnen met dit toestel worden
afgespeeld. (fig. H)
• Sommige CD-R’s (afhankelijk van de opname-apparatuur of de staat van
de disc) kunnen niet met dit toestel worden afgespeeld.
• U kunt geen CD-R afspelen die niet is gefinaliseerd*.
• Met dit toestel kunnen geen CD-RW’s (herschrijfbare CD’s) worden
afgespeeld.
* Proces dat nodig is om een opgenomen CD-R disc af te spelen met een CDspeler.
Note sui CD-R/CD-RW
• Con il presente apparecchio è possibile riprodurre CD-R (CD registrabili)
progettati per l’utilizzo audio. (fig. H)
• In base alle condizioni dell’apparecchio di registrazione o del CD-R
stesso, alcuni CD-R potrebbero non essere riprodotti su questo
apparecchio.
• Non è possibile riprodurre CD-R non finalizzati*.
• Con il presente apparecchio è possibile riprodurre CD-RW (CD
riscrivibili).
* Operazione necessaria per la riproduzione di un CD-R registrato su lettore CD
audio.
G
H
Look for this mark to distinguish CD-Rs for audio use.
Ce symbole permet de distinguer les CD-R conçus pour une utilisation audio.
Für den Einsatz als Tondatenträger konzipierte CD-Rs sind mit dieser
Markierung gekennzeichnet.
Audio CD-R’s zijn hieraan te herkennen.
Ricercare questo simbolo per distinguere i CD-R per utilizzo audio.
This mark denotes that a disc is not for audio use.
Ce symbole indique qu’un disque n’est pas conçu pour une utilisation audio.
Nicht für den Einsatz als Tondatenträger geeignete CD-Rs sind mit dieser
Markierung gekennzeichnet.
Dit geeft aan dat een disc niet geschikt is voor audiotoepassingen.
Questo simbolo indica che il disco non è destinato all’utilizzo audio.
CDX-T67
Installation
Installation
Installation
Installeren
Installazione
Precautions
Pr cautions
Sicherheitsma§nahmen
Voorzorgsmaatregelen
Precauzioni
• Choose the mounting location carefully, observing the
following:
— The unit is not subject to temperatures exceeding 55°C
(such as in a car parked in direct sunlight).
— The unit is not subject to direct sunlight.
— The unit is not near heat sources (such as heaters).
— The unit is not exposed to rain or moisture.
— The unit is not exposed to excessive dust or dirt.
— The unit is not subject to excessive vibration.
— The fuel tank should not be damaged by the tapping
screws.
— There should be no wire harnesses or pipes under the
place where you are going to install the unit.
— The spare tire, tools or other equipment in or under the
trunk should not be interfered with or damaged by the
screws or the unit itself.
• Be sure to use only the supplied mounting hardware for a
safe and secure installation.
• Use only the supplied screws.
• Make holes of ø 3.5 mm only after making sure there is
nothing on the other side of the mounting surface.
• Choisissez l’emplacement de montage en tenant compte
des observations suivantes :
— L’appareil ne doit pas être exposé à des températures
supérieures à 55°C (comme dans une voiture garée en
plein soleil).
— L’appareil ne doit pas être utilisé en plein soleil.
— L’appareil ne doit pas être utilisé près d’une source de
chaleur (comme un chauffage).
— L’appareil ne doit pas être utilisé dans un endroit
exposé à la pluie ou à l’humidité.
— L’appareil ne doit pas être utilisé dans un
endroitpoussiéreux ou sale.
— L’appareil ne doit pas être exposé à des vibrations
excessives.
— Vérifiez que le réservoir d’essence ne risque pas d’être
endommagé par les vis taraudeuses.
— Il ne doit pas y avoir de faisceau de fils ou de tuyaux à
l’emplacement du montage.
— Vérifiez que l’appareil ou les vis ne risquent pas
d’endommager ou de gêner la roue de secours, les
outils, ou tout autre objet dans le coffre.
• Pour garantir la sécurité de l’installation, utiliser
uniquement le matériel de montage fourni.
• Utilisez uniquement les vis fournies.
• Ne percez les trous de 3,5 mm de diamètre qu’après vous
être assuré qu’il n’y avait rien de l’autre côté de la surface
de montage.
• Bei der Wahl des Einbauortes ist folgendes zu beachten:
— Das Gerät darf keinen Temperaturen über 55 °C
ausgesetzt sein, wie sie z. B. in einem in der Sonne
geparkten Fahrzeug auftreten können.
— Das Gerät darf keiner direkten Sonneneinstrahlung
ausgesetzt sein.
— Das Gerät muß von Wärmequellen (z. B. der Heizung)
ferngehalten werden.
— Das Gerät darf weder Regen noch Feuchtigkeit
ausgesetzt sein.
— Das Gerät darf keinem übermäßigen Staub oder
anderer Verschmutzung ausgesetzt sein.
— Das Gerät darf keinen übermäßigen Vibrationen
ausgesetzt sein.
— Der Tank darf durch die Schneidschrauben nicht
beschädigt werden.
— Unter der Fläche, auf die das Gerät montiert werden
soll, dürfen sich keine Kabelbäume oder Leitungen
befinden.
— Ersatzreifen, Werkzeug usw. im oder unter dem
Kofferraum dürfen durch die Schneidschrauben nicht
beschädigt werden. Achten Sie auch darauf, daß die
Herausnahme des Ersatzreifens, Werkzeugs usw. nicht
durch das Gerät behindert wird.
• Für sicheren und stabilen Einbau verwenden Sie
ausschließlich die mitgelieferten Befestigungsteile.
• Verwenden Sie ausschließlich die mitgelieferten
Schrauben.
• Bohren Sie die Löcher mit einem Durchmesser von 3,5 mm
erst, wenn Sie sich vergewissert haben, daß sich nichts auf
der Rückseite der Montagefläche befindet.
• Kies de plaats van opstelling met zorg, zodat het toestel
niet:
— Onderhevig is aan temperaturen boven de 55°C (zoals
in een auto geparkeerd in de volle zon).
— Steeds blootgesteld wordt aan direkt zonlicht.
— Te dicht bij een warmtebron komt (zoals een
autoverwarming).
— Nat kan worden, door regen, vocht of opspattend
water.
— In kontakt komt met veel stof of vuil.
— Onderhevig is aan sterke trillingen of schokken.
— Let op dat de plaatschroeven de benzinetank niet
beschadigen.
— Kontroleer of onder de plaats waar u het apparaat wilt
monteren geen bedrading of leidingen lopen.
— Houd bij het monteren rekening met het reservewiel,
gereedschappen en-eventueel in de kofferruimte
aanwezige andere apparaten, zodat deze de compact
disc wisselaar niet in de weg zitten, noch beschadigd
kunnen worden door de montageschroeven van de
laatste.
• In het belang van een veilige en stevige montage dient u
uitsluitend het bijgeleverde montagemateriaal te
gebruiken.
• Gebruik enkel de meegeleverde schroeven.
• Controleer of er niets achter het bevestigingsvlak zit en
maak pas dan gaten van 3,5 mm diameter.
• Scegliere con cura il luogo di installazione, seguendo le
istruzioni riportate di seguito ed evitando di installare
l’apparecchio in luoghi:
— Soggetti a temperature oltre i 55°C (come in un’auto
parcheggiata al sole).
— Esposti alla luce solare diretta.
— Vicini a fonti di calore (come impianti di
riscaldamento).
— Esposti alla pioggia o all’umidità.
— Esposti a polvere o sporco eccessivi.
— Soggetti a vibrazioni eccessive.
— Il serbatoio del carburante non deve essere danneggiato
dalle viti filettanti.
— Non devono essere presenti né cavi né tubi sotto il
luogo scelto per l’installazione dell’apparecchio.
— Le viti e l’apparecchio stesso non devono interferire
con, o danneggiare, la ruota di scorta, gli attrezzi o altri
dispositivi presenti dentro o sotto il bagagliaio.
• Assicurarsi di usare solo il materiale di montaggio in
dotazione per un’installazione stabile e sicura.
• Utilizzare solo le viti in dotazione.
• Assicurarsi che non vi sia nulla sull’altro lato della
superficie di montaggio, quindi effettuare fori di solo 3,5
mm di diametro.
How to install the unit
Installation de l appareil
Installation des Ger tes
Installatie van het apparaat
Installazione dell apparecchio
Horizontal installation
Installation horizontale
Horizontaler Einbau
Horizontaal installeren
Installazione in orizzontale
1
2
Aligner sur le repère.
For details, refer to the Installation/Connections manual of each product.
Pour plus de d tails, consulter le manuel d installation/connexions de chaque produit.
Einzelheiten entnehmen Sie der Installations-/Anschlu§anleitung des betreffenden Ger ts.
Zie voor nadere bijzonderheden de gebruiksaanwijzing voor installatie en aansluitingen
van de aan te sluiten apparatuur.
Per i dettagli, fare riferimento al manuale di installazione/collegamenti dell autoradio.
Connection diagram/Sch ma de connexion/Anschlu§diagramm/
Aansluitingsschema/Schema di collegamento
To the car audio (the master unit) compatible with the Sony Bus or the source selector
Vers le système audio voiture (appareil principal) compatible avec le bus Sony ou le
sélecteur de source.
an Autoanlage (Hauptgerät), die mit dem Sony-Bus oder dem Signalquellenwähler
kompatibel ist
Op het car audiosysteem (hoofdtoestel) dat compatibel is met Sony Bus of de
bronkeuzeschakelaar
All’autoradio (unità principale) compatibile con bus Sony o con il selettore di
sorgente.
BUS AUDIO IN
BUS CONTROL IN
4
5
3
2
Align with the marked position.
Connections/Connexions/
Anschlu§/Aansluitingen/
Collegamenti
3
Auf die richtige Position stellen.
1
Stel aldus in op het merkteken.
2
Allineare con il punto segnato.
1
¿ 3.5 mm
CDX-T67
Vertical installation
Installation verticale
Vertikaler Einbau
1
Vertikaal installeren
Installazione in verticale
3
2
Note
For connecting two or more changers, the XA-C30 source selector (optional) is necessary.
Remarque
Pour raccorder deux ou plusieurs changeurs, le sélecteur de source XA-C30 (en option) est nécessaire.
Align with the marked position.
VERTICAL
2
Aligner sur le repère.
3
Auf die richtige Position stellen.
1
Stel aldus in op het merkteken.
2
Allineare con il punto segnato.
Opmerking
Om twee of meer wisselaars aan te sluiten is de optionele geluidsbronkiezer XA-C30 vereist.
1
¿ 3.5 mm
Nota
Per collegare uno o più cambia CD, è necessario il selettore di fonte XA-C30 (opzionale).
Suspended installation
Installation suspendue
H ngender Einbau
Hangend installeren
Installazione in sospensione
When the unit is to be installed under the rear tray
etc. in the trunk compartment, make sure the
following provisions are made.
Si l’appareil doit être installé sous la plage arrière
dans le coffre par exemple, observer les précautions
suivantes.
Bei hängender Installation unter der Heckablage
usw. im Kofferraum beachten Sie folgende
Vorsichtsmaßnahmen:
Als u het apparaat onder de hoedenplank of iets
dergelijks wilt installeren, let dan op de volgende
punten:
Se l’apparecchio deve essere installato sotto il ripiano
posteriore, nel bagagliaio, ecc., assicurarsi di
prendere le seguenti precauzioni:
• Choose the mounting location carefully so that the unit can
be installed horizontally.
• Make sure the unit does not hinder the movement of the
torsion bar spring etc. of the trunk lid.
• Choisissez l’emplacement pour pouvoir installer l’appareil
à l’horizontale.
• Vérifiez que l’appareil ne gêne pas les mouvements du
ressort de fermeture du coffre, entre autres.
• Wählen Sie den Befestigungsort sorgfältig so aus, daß das
Gerät horizontal montiert werden kann.
• Achten Sie darauf, daß das Gerät die
Heckklappendämpfer usw. nicht behindert.
• Kies een geschikte plek waar u het apparaat horizontaal
kunt ophangen.
• Vergewis u ervan dat het apparaat niet beschadigd kan
worden door bewegende onderdelen zoals een
kofferdeksel, de veren van de vijfde deur, enz.
• Scegliere con attenzione il luogo di montaggio in modo
che l’apparecchio possa essere installato orizzontalmente.
• Assicurarsi che l’apparecchio non ostacoli il movimento
della molla della barra di torsione ecc. del coperchio del
cofano.
1
¿ 3.5 mm
Align with the marked position.
2
Aligner sur le repère.
Auf die richtige Position stellen.
Stel aldus in op het merkteken.
Allineare con il punto segnato.
2
1
2
1
3
3
Inclined installation
Installation inclin e
Installation in geneigter Position
Niet-horizontale plaatsing
Installazione in posizione inclinata
After installing the unit, align the dials with one of
the marks so that the arrows are as vertical as
possible.
Après avoir installé l’appareil, alignez le disque sur
l’un des repères afin que la flèche soit aussi proche
que possible de la position verticale.
Nach dem Installieren des Geräts richten Sie die
Dial-Ringe an einer der Markierungen aus, so daß
der Pfeil möglichst senkrecht steht.
Zodra de eenheid geplaatst is, draait u de ringen op
een stand waarbij de pijl zoveel mogelijk in een
vertikale positie staat.
Dopo aver installato l’apparecchio, allineare le
manopole ad una delle tacche in modo che la freccia
sia il più verticale possibile.
Note
Be sure to align the left and right dials with the same
mark.
Remarque
Veillez à aligner les disques gauche et droite sur le même
repère.
Hinweis
Achten Sie darauf, den linken und rechten Dial-Ring an
derselben Markierung auszurichten.
Opmerking
Zet de linker-en de rechterring op dezelfde stand.
Nota
Accertarsi di allineare le manopole di sinistra e di destra
alla stessa tacca.
4
Hinweis
Zum Anschließen von zwei oder mehr Wechslern wird der gesondert erhältliche Signalquellenwähler
XA-C30 benötigt.
4
CDX-T67
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1.
DISASSEMBLY FLOW
Note 1: The process described in
can be performed in any order.
Note 2: Without completing the process described in
, the next process can not be performed.
SET
2-2. FRONT PANEL (S) ASSY, CASE (UPPER S)
(Page 6)
2-3. MECHANISM DECK (MG-276A-159)
(Page 6)
2-4. JACK BOARD
(Page 7)
2-5. BELT (TS)
(Page 7)
2-6. MAIN BOARD
(Page 8)
2-9. LE MOTOR ASSY
(CHUCKING)
(M103)
(Page 9)
2-7. ESCUTCHEON (S),
SLIDE VARIABLE RESISTOR
(ELEVATOR HEIGHT SENSOR)
(RV301)
(Page 8)
2-8. MD MOTOR ASSY
(ELEVATOR)
(M104)
(Page 9)
2-10. RF BOARD
(Page 10)
2-11. SLED MOTOR
COMPLETE ASSY
(M101)
(Page 10)
2-12. OPTICAL PICK-UP
(KSS-720A)
(Page 11)
2-13. CHASSIS (EV) ASSY
(Page 11)
2-14. LEVER (CHK.L) ASSY,
LEVER (CHK.R) ASSY
(Page 12)
2-15. CHASSIS (OP) BLOCK SERVICE ASSY
(Page 12)
5
CDX-T67
Note: Follow the disassembly procedure in the numerical order given.
2-2.
FRONT PANEL (S) ASSY, CASE (UPPER S)
3 screw
(PTT2.6 × 6)
4 case (upper S)
5 lever (FLT. 838)
1 screw
(PTT2.6 × 6)
3 screw
(PTT2.6 × 6)
2 front panel (S) assy
5 lever (FLT. 838)
1 screw
(PTT2.6 × 6)
2-3.
MECHANISM DECK (MG-276A-159)
2 spring (FLT S)
4 mechanism deck
(MG-276A-159)
2 spring (FLT S)
1 two dampers (S)
3 jack flexible board
(CN901)
1 two dampers (S)
6
CDX-T67
2-4.
JACK BOARD
2 screw (FP)
1 Remove ten solders
of the cord (with connector).
3 jack board
4 ground point screw
(PTT2.6 × 6)
5 cord (with connector)
(BUS/RCA)
2-5.
BELT (TS)
3 two screw (FP)
4 rack (UD)
belt (TS)
5 belt (TS)
2 3.5 washer
1 screw
(M1.7 × 2.2)
7
CDX-T67
2-6.
MAIN BOARD
3 three screws (FP)
2 Remove three solders
of the slide variable resistor (RV301).
4 main board
1 main flexible board
(CN101)
2 Remove two solders
of the elevator motor
lead wires (M104).
2-7.
ESCUTCHEON (S), SLIDE VARIABLE RESISTOR (ELEVATOR HEIGHT SENSOR) (RV301)
2 three claws
3 escutcheon (S)
slide variable resistor
(elevator height sensor)
(RV301)
2 three claws
2 claw
1 screw (FP)
4 slide variable resistor
(elevator height sensor)
(RV301)
8
CDX-T67
2-8.
MD MOTOR ASSY (ELEVATOR) (M104)
1 screw
(PTT2 × 3)
2 bracket (MDM)
3 MD motor assy (elevator)
(M104)
2-9.
LE MOTOR ASSY (CHUCKING) (M103)
3 screw
(P1.7 × 2.2)
7 bracket (LEM)
2 tension spring (rack)
4
6 LE motor assy
(chucking)
(M103)
5
1 Remove two solders of
the chucking motor lead wires (M103).
9
CDX-T67
2-10. RF BOARD
3 two screws
(PS2 × 4)
4 heat sink
1 main flexible board
(CN101)
5 screw
(PS2 × 4)
6 RF board
2 Remove two solders of
the sled motor lead wires
(M101).
1 OP flexible board
(CN102)
2 Remove two solders of
the spindle motor lead
wires (M102).
2 Remove two solders of
the chucking motor lead wires
(M103).
2-11. SLED MOTOR COMPLETE ASSY (M101)
1 screw
(P2 × 2.2)
2 sled motor complete assy
(M101)
10
CDX-T67
2-12. OPTICAL PICK-UP (KSS-720A)
2 two screws
(P2 × 3)
6 gear (SL2)
8 screw
(P2 × 3)
5 washer
(DIA. 1.2)
3 spring (sled front point)
9 detent spring (sled)
7 bearing (sled) assy
0 shaft (sled feed) assy
1 OP flexible board
qa optical pick-up (KSS-720A)
4 Lift up the bearing (sled) assy in the
direction of arrow A and remove it from
the shaft (sled feed) assy.
A
2-13. CHASSIS (EV) ASSY
5 shaft (EVGR)
7 chassis (EV) assy
6 two shafts (EVGL)
1 tension spring
B
4 Open the main chassis assy
in the direction of arrow B.
A
2 Move the slider (6R) fully in the
direction of arrow A to move the
chassis (EV) assy down.
3 three screws
(PTT2 × 3)
11
CDX-T67
2-14. LEVER (CHK.L) ASSY, LEVER (CHK.R) ASSY
3 Move the lever (CHK.L) assy
fully in the direction of arrow A.
A
4 lever (CHK.L) assy
1 screw
(P1.7 × 2.2)
leaf spring (D retainer R)
2 joint (CHK)
B
A
3 Move the lever (CHK.R) assy
fully in the direction of arrow A.
5 Remove the lever (CHK.R) assy pushing down
the leaf spring (D retainer R) in the direction of arrow B.
2-15. CHASSIS (OP) BLOCK SERVICE ASSY
2 screw
(P2 × 1.8)
8 chassis (OP) block service assy
3 leaf spring (FOP)
6 shaft
7 shaft
6 shaft
B
5 Open the chassis (EV) assy
in the direction of arrow B.
A
4 type-E stop ring 2.0
1 Turn the gear (LE2) assy
fully in the direction of arrow A.
12
CDX-T67
SECTION 3
MECHANICAL ADJUSTMENT
• Elevator Height (Address) Adjustment
Note: This adjustments is necessary when the system controller (IC301),
variable resistor (RV302), lever (CHK.L) assy, lever (CHK.R) assy,
or chassis (EV) assy was replaced for any repair.
Connection:
power supply
(DC 14.4 V)
master unit
+
GND
Adjustment Method:
1. Connect this set to the master unit (e.g. MDX-C7970/C7970R),
load a disc magazine, and place the set vertically as shown
below.
2. Connect the regulated power supply to the master unit, and
turn the power on.
3. Press the DISC button on the master unit and select DISC 6.
4. Adjust the variable resistor RV302 so that the reference holes
of the slider (6L) and of the chassis (6B) meet within an error
of ±0.15 mm when the tray is loaded at address 6.
BUS cable
compact disc changer
chassis (6B)
slider (6L)
slider (6L)
(reference hole)
chassis (6B)
(address 6 hole)
slider (6L)
(reference hole)
RV302
0.15mm
0.15mm
13
CDX-T67
SECTION 4
ELECTRICAL CHECK
Note:
1. This check is performed with the set placed horizontally.
2. Power supply voltage: DC14.4 V (more than 3 A).
3. Be sure to use the disc “YEDS-18” parts code: 3-702-101-01, but only
when indicated.
Focus Bias Check
Connection:
oscilloscope
(AC range)
power supply
(DC 14.4 V)
Connection:
– RF Board (Component Side) –
+
–
master unit
+
GND
BUS cable
IC101
TP (RFAC)
TP (VC)
compact disc changer
Procedure:
1. Connect the oscilloscope to TP (RFAC) and TP (VC) on the
RF board.
2. Put the set into play mode by loading the disc (YEDS-18).
3. Confirm that oscilloscope waveform is clear and check RF signal level is correct or not.
Note:
Clear RF signal waveform means that the shape “◊” can be clearly distinguished at the center of the waveform.
RF signal waveform
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
(10 : 1 probe in use)
0.3
level: 1.4 +– 0.4
Vp-p
When observing the eye pattern, set the oscilloscope to AC range
and raise the vertical sensitivity so that it may be easily seen.
14
CDX-T67
Tracking Offset Check
Connection:
– RF Board (Component Side) –
oscilloscope
(DC range)
+
–
TP (TE)
IC101
TP (VC)
Procedure:
1. Connect the oscilloscope to TP (TE) and TP (VC) on the RF
board.
2. Put the set into play mode by loading the disc (YEDS-18).
3. Press the [.AMS >] button on the master unit, and check
the traverse waveform*.
4. Confirm that the oscilloscope waveform is symmetrical on the
top and bottom in relation to 0 V dc, and check this level.
* Traverse waveform: This is the tracking error wave form appears
when crossing the track.
Traverse waveform
VOLT/DIV: 500 mV
TIME/DIV: 2 ms
Center: 0 V
A
0V
B
A=B
traverse waveform
(100 track jump waveform)
15
CDX-T67
MEMO
16
CDX-T67
SECTION 5
DIAGRAMS
5-1.
BLOCK DIAGRAM – SERVO Section –
FILTER
RF AMP,
FOCUS/TRACKING ERROR AMP
IC101
6
B
7
C
8
I-V AMP
D
9
RFAC
SUMMING
AMP
A
EQ
IN
4
3
FILO
RF EQ RFAC
15
AMP
RFAC
VCA
C
RFDC
SUMMING
AMP
D
RFDCO
10
11
E
FE
TRACKING
ERROR
AMP
F
28
ASYMMENTRY
CORRECTOR
DIGITAL
PLL
EFM
DEMODULATOR
TE
16
18
AOUT2
DIGITAL FILTER,
NOISE SHAPER
LD
1
LD
DIGITAL SIGNAL PROCESSOR,
DIGITAL SERVO PROCESSOR,
DIGITAL FILTER, D/A CONVERTER
IC401
FE
APC AMP
BUFFER
LOUT2
TIMING
LOGIC
XTAI
72
75
(L)
GROUNDISOLATION
IC501
(R)
67
X401
16.9344MHz
60
MUTING
Q502, 503
TE
EMPH
12
PD
AIN1
GFS
2
99 RW SWL
64
66 EMPH
18
42 GFS
MUTE 67
MUTING CONTROL
SWITCH
Q501
RFDC
FE
TE
PD
AUTOMATIC
POWER
CONTROL
Q101
71
CLOCK
GENERATOR
ERROR
CORRECTOR
RW/ROM
SW
76
XTAO
CD-ROM/RW
SELECT SWITCH
Q301
LASER DIODE
77
PWM
&
AOUT1
INTEGRATOR
70
LOUT1
AIN2
16k RAM
RF AMP OFFSET
CONTROL SWITCH
Q102
30
SERIAL
IN
INTERFACE
D/A
INTERFACE
RFDC
RW/ROM
FOCUS
ERROR
AMP
F
RFAC
ASYI
49
ASYO
48
B
DC OFST
E
51
CN902 (1/2)
INTERNAL BUS
A
AC
SUM
CLTV
PCO
FILI
DETECTOR
54 53 56 55
DATA
5
CLOK
7
XLAT
6
61 CDDAT
59 CDCLK
60 CDLAT
43 39 41 40
RFDC
FE
TE
SE
OPTICAL
PICK-UP BLOCK
(KSS-720A)
6
7
VO4+
VO4–
VIN4+
COIL
DRIVE
VIN4–
A/D CONVERTER
31
30
32
31
TEDR
9
M101
(SLED)
M
12
13
VO3–
VO1+
VO1–
COIL
DRIVE
VIN3–
25
32
24
33
VIN1+B
19
MOTOR
DRIVE VIN1–B 18
28
29
FRDR
DIGITAL SERVO
SIGNAL PROCESS
8
FFDR
PWM GENERATOR
(FOCUS)
VIN3+
44 SENS
SUBCODE
PROCESS
CPU
INTERFACE
SQSO
1
SQCK
2
SCOR
20
56 SQSO
58 SQCK
52 SCOR
TRDR
(TRACKING)
VO3+
8
OP AMP
ANALOG SWITCH
TRACKING/FOCUS COIL DRIVE,
SLED/SPINDLE/CHUCKING
MOTOR DRIVE
IC201
2-AXIS DEVICE
SENS
MIRR
DFCT
FOK
SYSTEM CONTROLLER
IC301 (1/2)
SERVO AUTO
SEQUENCER
SERVO
INTERFACE
SFDR
SCLK
SRDR
FOK
M
10
11
VO2+
VO2–
MOTOR
DRIVE
VIN2–
21
26
MDP
43 SCLK
24
41 FOK
XRST 3
DIGITAL
CLV
62 XRST
SSTP
M102
(SPINDLE)
9
• SIGNAL PATH
: CD PLAY
27
M103
(CHUCKING)
M
5
4
VL0+
VL0–
FWD
MOTOR
DRIVE
REV
5 LOADF
1
6 LOADR
2
ON : When the optical pick-up
is inner position
ON : When completion of the disc
chucking operation
SW101
(LIMIT)
98 LIM SW
SW102
(CHUCKING END DETECT)
97 LOAD SW
96 SAVE SW
17
17
CDX-T67
5-2.
BLOCK DIAGRAM – BUS CONTROL/POWER SUPPLY Section –
SYSTEM CONTROLLER
IC301 (2/2)
SW301
MAGAZINE
DETECT
RV302
ELEVATOR HEIGHT
(ADDRESS)
MCK 37
95 MAG SW
SW302
MAGAZINE IN/OUT
DETECT
RV301
ELEVATOR HEIGHT
SENSOR
EHS 36
51 MAGLK SW
AVRH 34
ELEVATOR
MOTOR DRIVE
IC302
OUT1
9
OUT2
7
MOTOR
DRIVE
IN1
3
IN2
4
4 ELVF
3 ELVR
SERVO +3V
D209
+3V
REGULATOR
Q202
SW303
+5V
REGULATOR
IC203
SERVO +5V
Z
DRIVER +8V
EJECT SW 50
+8V
REGULATOR
IC202
ELVON 24
RESET 75
RESET SIGNAL
GENERATOR
IC204
CN902 (2/2)
REGULATOR
Q205, 206
µCOM B+
IC901
8
B. UP
BUS INTERFACE
(FOR SONY BUS)
IC201
VCC 14
UNI SI 16
10
UNI SO 17
9
UNI CK 18
11
BUSON 45
1
13
X0
M
X1
M104
(ELEVATOR)
D210
BATTERY
CHECK
Q303
BUCHK 46
81
80
X301
4MHz
18
18
8
SO
DATA
6
DATA
6
SI
SCK
CLK
BUSON OUT
LOF
BUSON OUT
BUSON IN
RESET
RESET
SWITCH
RST
5
CLK
4
12
4
BUSON
2
7
7
RST
CDX-T67
5-3.
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
f
: internal component.
•
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
•
: internal component.
• C : panel designation.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
• Waveforms
– RF Board –
– MAIN Board –
1 IC101 qg (RFAC) (CD play mode)
1 IC301 ia (X1) (CD play mode)
0.3
1.4 +– 0.4
Vp-p
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce por tant le numéro
spécifié.
3.8 Vp-p
250 ns
2 IC101 qh (FE) (CD play mode)
• A : B+ Line.
• H : adjustment for repair.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from CD changer controller.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : CD PLAY
2 IC401 wh (MDP) (CD play mode)
1.8 Vp-p
Approx
180 mVp-p
7.5 µs
3 IC101 qk (TE) (CD play mode)
3 IC401 yj (XTAO) (CD play mode)
Approx
900 mVp-p
4.2 Vp-p
59.1 ns
19
19
CDX-T67
Ver 1.1
5-4.
PRINTED WIRING BOARDS – RF Board –
2
1
3
4
5
6
7
8
9
10
RF BOARD (COMPONENT SIDE)
A
11
12
13
14
RF BOARD (CONDUCTOR SIDE)
RED
M
(CHASSIS)
M101
(SLED)
BLK
CN101
OP FLEXIBLE
BOARD
B
R121
C119
R120
C114
TP
(TE)
A
(Page 22)
R109
IC101
R117
TP
(RFAC)
C117
1
C116
MAIN
FLEXIBLE
BOARD
C110
2
C
MAIN
BOARD
CN202
16
10
CN
R106
OPTICAL
PICK-UP
BLOCK
KSS-720A
C109
C112
SW101
(LIMIT)
C113
TP
(VC)
D
R118
C111
R128
R113
R116
R119
R111
R112
Q101
R110
Q102
C115
R103 R127
C108
E
R218 C211
R214 R213
R220
M102
(SPINDLE)
R223
R222
M
R216
R219
C208
C107
C209
R211
R212
R209
R210
R215
C202
C206
R207
F
R208
IC201
C205
BLK
RED
R205
R206
C204
R203
C203
R204
R202
C217 R201
G
11
1-680-829-
C201
(11)
C220
BLK
RED
SW102
SW102
(CHUCKING END DETECT)
11
1-680-829-
H
M
M103
(CHUCKING)
• Semiconductor
Location
Ref. No.
Location
IC101
IC201
C-5
F-6
Q101
Q102
D-6
E-5
20
20
(11)
CDX-T67
Ver 1.1
5-5.
SCHEMATIC DIAGRAM – RF Board –
• See page 19 for Waveforms.
• See page 27 for IC Block Diagrams.
Q101
2SB624T1-BV345
C111
0.1
AUTOMATIC
POWER CONTROL
R127
22
R119
1k
C110
100
6.3V
RF AMP,
FOCUS/TRACKING
R103
22
C107
100
4V
ERROR AMP
R118
22k
DC_
LD
OFST
PD
C116
0.1
R128
1k
R117 3.3k
RFDCI
EQ_
16
RFDCO
IN
C112
0.1
C113 0.1
AC_SUM
CN102
16P
F(-)
VC
GND
RFC
A
VFC
R116
100k
Q102
DTC124EKA
-T146
2-AXIS
DEVICE
(FOCUS)
(TRACKING)
DETECTOR
T(-)
B
BST
T(+)
C
RFG
F(+)
D
VCC
E
CEI
R113
15k
R120 22k
VCC
LASER DIODE
VC
F
F
CE
VCC
SW
VC
DVCC
VR
DVC
PD
RFAC
CONTROL SWITCH
R111
10k
R121 22k
E
RF AMP OFFSET
R110
18k
R109
100k
R112
10k
TE_BAL
TE
R106 100k
PD
I-V
FEI
SW101
AMP
LD
C117
0.1
LD
C115
100
4V
GND
(LIMIT)
FE
ON:WHEN THE OPTICAL PICK-UP IS
C114
0.1
C119
0.1
INNER POSITION
IC101
CXA2581N-T4
SW102
A
(CHUCKING END DETECT)
C
OP
FLEXIBLE
BOARD
ON:WHEN COMPLETION OF THE DISC
CHUCKING OPERATION
B
D
CN101
22P
1
R/RW_SEL
SW101
LIM_SW
SW102
SAVE_SW
TP(RFAC)
RFAC
RFDC
C108
100
4V
TP(VC)
C109
0.1
VC
TP(TE)
TE
FE
DVCC(3V)
GND(5V)
5V
AA1
FRDR
AA2
FFDR
AA3
TRDR
AA4
TFDR
AA5
MDP
AA6
SRDR
FOCUS/TRACKING COIL DRIVE
AA7
SPINDLE/SLED/CHUCKING
MOTOR DRIVE
IC201
LA6576L-TE
(Page 25)
MAIN
FLEXIBLE
BOARD
C202
0.1
C201
470
16V
SFDR
R201
10k
R202
10k
C217
0.1
LOADR
LOADF
GND(8V)
FWD
S-GND
REV
MUTE2
VCC2
MUTE1
8V
TP1
M103
C220
0.1
VL0-
C203
470p
VIN4
TP2
(CHUCKING)
VL0+
VIN4-
VO4+
VIN4+
R203
10k
R204
33k
AA3
AA4
VO4-
C204
470p
VREF-IN
VO3+
VIN1-SW
VO3-
VREF-OUT
R205
10k
R206
33k
R222
1k
R223
820
TP3
M102
C205
470p
TP4
(SPINDLE)
R207
10k
R208
33k
AA2
AA1
VO2+
REG-OUT
VO2-
REG-IN
VO1+
VIN3+
VO1-
VIN3-
C206
470p
TP6
M101
R209
10k
R210
33k
TP5
(SLED)
VCC1
VIN3
VIN1
VIN2+
VIN1-A
VIN2-
R211
47k
R212
68k
R220
12k
AA5
VIN1+A
VIN1-B
C208
0.022
VIN2
R213
47k
R214
56k
VIN1+B
C211
0.022
R218
10k
R219
33k
C209
0.022
R215
10k
R216
33k
AA7
AA6
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
21
21
Les composants identifiés par une marque 0 sont
critiques pour la sécurité. Ne les remplacer que
par une pièce portant le numéro spécifié.
CDX-T67
5-6.
PRINTED WIRING BOARDS – MAIN Board (Component Side) –
Ver 1.1
• Semiconductor
Location
3
4
5
6
7
8
9
10
Location
D201
D202
D203
D204
D207
D209
D210
D212
D213
G-7
G-7
B-5
G-6
F-7
F-6
F-6
G-9
G-7
IC201
IC203
IC204
IC301
IC302
IC401
IC501
G-6
B-10
E-6
D-7
E-4
C-4
G-4
B-5
F-5
E-9
F-7
E-3
F-5
H-6
H-6
A
MAIN BOARD (COMPONENT SIDE)
C306
2
C305
D203
B
C203
IC203
R308
C415
R412
1
R202
R307
C414
Q202
C413
C416
R407
R405
3
C215
IC301
R302
C403
R410
R305
C303
R303
IC401
R408
C
+
Q202
Q203
Q205
Q206
Q301
Q501
Q502
Q503
2
C411
R406
C412
C214
C410
R404
C408
D
C401
R403 R401
C407
R414
C402
R301
R402
CN202
C302
R306
C301
R506
Q301
R505
R309
E
R501
R502
C502
C504
IC204
Ref. No.
1
C501
R504
C503
R503
C211
C304
Q205
C212
F
MAIN
FLEXIBLE
BOARD
C307
R205
D209
C308
C213
R206
IC302
C208
D210
R211
R203
R209
R204
D207
Q203
A
RF BOARD
CN101
R517
R515
R514
IC201R201
R518
R513
R512
SW302
C202
Q501
C506
(Page 20)
G
Q206
R207
D201
1
IC501
CN201
13
D213
C516
C216
D202
R520
R511
C505
D212
C514
R519
C201 D204
Q502
C217
SW302
MAGAZINE
IN/OUT
DETECT
11
1-680-827-
R508
C513 R510
H
R507
R521
JACK FLEXIBLE
BOARD
Q503
R509
B
JACK BOARD
CN901
(Page 26)
22
22
(11)
5-7.
PRINTED WIRING BOARD – MAIN Board (Conductor Side) –
1
2
3
CDX-T67
4
5
6
7
8
9
10
• Semiconductor
Location
Ref. No.
MAIN BOARD (CONDUCTOR SIDE)
A
IC202
SW303
Z
B
RV301
EVEVATOR HEIGHT
SENSOR
(CHASSIS)
C206
C205
C207
RV302
C
C204
D
C404
IC202
X401
C405
E
X301
C209
SW301
MAGAZINE
DETECT
F
(CHASSIS)
C210
C508
G
(CHASSIS)
C511
RED
C510
M
C512
BLK
C509
H
C515
11
1-680-827-
23
23
(11)
M104
(EVEVATOR)
Location
D-2
CDX-T67
Ver 1.1
SCHEMATIC DIAGRAM – MAIN Board (1/2) –
• See page 19 for Waveform. • See page 27 for IC Block Diagrams.
1
IC201
BA8272AFV-E2
CN201
13P
BUSON
CLK
2
SCK
Q301
DTC124EKA
SCK
SI
CLK
VREF
SO
DATA
DATA
SI
CD-ROM/RW
SO
SAVE_SW
BUSON
SELECT
SWITCH
BP5
BP6
BP10
SW301
C302
0.01
(FOR SONY BUS)
C202
4700p
I
C208
0.1
O
G
R209
47k
X1A
X0A
X0
VSS
X1
VCC
RAMIO1
RAMA0
RAMIO0
RAMA1
RAMA2
RAMA3
SINGLE
CFSEL
TEXTSEL
TEST
ESPSEL
6/10 SEL
GENERATOR
IC204
XC61CN2502PR
Q205,206
REGULATOR
MAG SW
RAMA5
SAVE SW
RESET SIGNAL
LIM SW
RAMA4
R205
47k
LOAD SW
C216
0.01
Q206
2SC2712-YG
D207
MA8056-H
X301
4MHz
C301
0.01
BUS INTERFACE
Q205
2SB1202FAST-TL
R204
47k
BP7
RESET
RW SEL
GND
D202 MA8180-TX
GND
D212 RB521S-30-TE61
GND
D204 RB521S-30-TE61
B.UP
C201
0.001
RAMIO2
R301
1k
RESET
RAMA6
RAMIO3
ELVR
RAMIO4
ELVF
RAMIO5
LOADF
RAMIO6
LOADR
RAMIO7
LOADF
3
LOADR
R211
100k
C209
100
6.3V
C210
1000
16V
RAMA7
C211
0.01
C212
0.01
RAMCS
RAMA12
RAMA10
VSS
MUTE
RAMA14
EMPH
RAMWE
XWRE
RAMA13
XRDE
EMPH
C206 100
4
16V
C204
1000
16V
IC202
NJM2395AF08
CONT
I
+5V REGULATOR
GND
G
O
RAMA8
VIN
SYSTEM CONTROLLER
XQOK
XRST
IC301
MB90473PFV-G
-113-BNDE1
RAMA9
VOUT
RAMA11
C214
0.01
C215
0.01
DATA
XLAT
UNI SI
CDLAT
UNI SO
CDCLK
UNI CK
SQCK
CLOK
SO
+8V REGULATOR
(Page 25)
XRST
CDDAT
SI
IC203
NJM78M05DL
SQCK
SCK
C207 100 6.3V
D203
MA8039-H-TX
R202 220
LEDDAT
NC
LEDCLK
SQSO
SQSO
C205
100
16V
VCC
C203
0.1
HS
LEDLAT
NC
CDON
ELVON
MD2
MD1
MD0
BUCHK
BUSON
SENS
SCLK
GFS
FOK
VSS
KEY1
KEY0
MCK
EHS
AVSS
AVRH
EEDAT
AVCC
5
MAGLK SW
EJECT SW
C308
0.01
SW302
MAGAZINE
R203
150k
SENS
6
SW303
D210
UDZS-TE17
-6.2B
D209
1SS355TE
-17
C213
0.33
BUSON
C305
1
SCLK
R207
100k
GFS
ELEVATOR
MOTOR DRIVE
FOK
IN/OUT DETECT
R307 10k
BP11
NC
BP12
M104
(ELEVATOR)
R302
100k
SCOR
RX
NC
C304
0.01
FL BOOT
LB1930M-TL
EECLK
IC302
C307
0.01
NC
+3V REGULATOR
GRSCOR
SCOR
Q202
2SC2712-YG
TX
JACK
FLEXIBLE
BOARD
B.UP
D213
RB521S-30-TE61
(Page 26)
DETECT
R201
47k
B.UP
R309
1k
MAGAZINE
BP9
RST
RST
SW301
BP8
C217 0.1
AGND
LIM_SW
RCH
BUSON
VCC
OUT
BUSON BUSON
IN
OUT
GND
LOF
LCH
D201 MA8180-TX
5-8.
R305
100k
Q203
2SC2712-YG
R206
120k
R308
10k
7
R303
100k
8
RV301
BATTERY
ELEVATOR HEIGHT
CHECK
SENSOR
RV301
10k
RV302
47k
C303
10
16V
9
10
11
12
24
24
CDX-T67
5-9. SCHEMATIC DIAGRAM – MAIN Board (2/2) –
• See page 19 for Waveforms. • See page 27 for IC Block Diagram.
1
2
R501
10k
R306
10
R502
10k
R503
10k
R504
10k
C501
150p
C502
150p
EMPH
C503
0.001
C504
0.001
R505
10k
R506
10k
R509
100k
C513
100p
C505
220p
PCMD
BCK
EMPH
XTAI
XTAO
XVSS
AVDD1
AIN1
AOUT1
LOUT1
AIN2
AVSS1
AVSS2
C401
0.1
3
SQSO
LOUT2
SQSO
AOUT2
LMUT
R519
6.8k
RMUT
R520
12k
C512
10
16V
AVDD2
C404
220
16V
XVDD
X401
16.9344MHz
C405
220
16V
R507
220
C402
0.01
LRCK
DOUT
SQCK
SQCK
XRST
VDD
R414 1k
XRST
VSS
SYSM
AVDD3
R401 3.3k
DATA
Q503
UN2226
MUTING
DATA
R511
12k
C515
47
4V
PCO
XLAT
R512
6.8k
R402
3.3k
XLAT
FILI
CLOK
FILO
SENS
CLTV
CLOK
C407
0.047
R403
10k
SENS
4
R521
10k
SCLK
SCLK
(Page 24)
R404
1M
AVSS3
VDD
RFAC
DIGITAL SIGNAL PROCESSOR,
DIGITAL SERVO PROCESSOR,
ATSK
BIAS
DIGITAL FILTER,D/A CONVERTER
SPOA
VCC
C410
220p
ASYI
IC401
CXD3017Q
SPOB
XLON
AVDD0
WFCK
IGEN
LIM_SW
SAVE_SW
ADIO
RFAC
GFS
RFDC
RFDC
SAVE_SW
VC
TE
R408
33k
C413
220p
SE
FE
VC
XTSL
TES1
TEST
FFDR
TFDR
SFDR
SSTP
MDP
VSS
TE
FRDR
SCOR
TRDR
CE
SRDR
C2PO
COUT
R508
220
R/RW_SEL
LIM_SW
C412
0.47
XPCK
LOCK
5
C411
0.01
TP403
TP404
R510
100k
C416
0.01
C403
2200p
AVSS0
FOK
SCOR
R406
100k
XUGF
DFCT
GND
GFS
R405
10k
TP402
MIRR
MUTING
100p
Q502
UN2226
TP401
C514
IC501
TLV2362IPW
CN202
22P
ASYO
R407 33k
GROUND-ISOLATION
C408
1500p
FE
DVCC(3V)
C511
10
16V
GND(5V)
R518
12k
R513
6.8k
5V
FRDR
Q501
DTA115EKA-T146
FRDR
FFDR
MUTING CONTROL
FFDR
TRDR
R517
6.8k
TRDR
R514
12k
C414
0.1
TP408
TP405
R515
10k
TP407
C506
220p
TP406
SWITCH
R410
100k
TFDR
MDP
MDP
SRDR
SRDR
SFDR
C509
47
4V
SFDR
FRDR
FFDR
TRDR
TFDR
SRDR
C415
220p
SFDR
LIM_SW
C510
47
4V
MDP
6
C516
0.01
FOK
C508
47
4V
R412
33k
LOADR
LOADR
LOADF
LOADF
GND(8V)
7
8V
C306
0.1
8
(CHASSIS)
9
10
11
12
25
25
(Page 21)
TFDR
MAIN
FLEXIBLE
BOARD
CDX-T67
5-10.
PRINTED WIRING BOARDS – JACK Board –
5-11.
SCHEMATIC DIAGRAM – JACK Board –
CN902
10P
CN901
13P
FB901
(L)
JACK BOARD
LCH
LCH
FB902
AGND
AGND
FB903
(R)
(COMPONENT SIDE)
RCH
RCH
BUSON
BUSON
CLK
CLK
DATA
DATA
RST
RST
(FOR SONY BUS)
B.UP
GND
GND
B.UP
IC901
B.UP
B.UP
GND
GND
GND
(CHASSIS)
11
1-680-828-
(11)
(FOR SONY BUS)
6
3
(R)
(L)
7
8
JACK BOARD
4
5
2
1
(CONDUCTOR SIDE)
10
IC901
1
FB901
FB903
CN902
FB902
CN901
13
11
1-680-828-
(11)
JACK FLEXIBLE
BOARD
B
(CHASSIS)
MAIN BOARD
CN201
(Page 22)
26
26
(Page 24)
JACK
FLEXIBLE
BOARD
CDX-T67
• IC Block Diagrams
– RF Board –
IC101
CXA2581N-T4
RW/ROM
A
30 DC OFST
29 RFDCI
–
+
B
–
+
28 RFDCO
C
D
DVC
DVC
VCC
VC
–
+
DVC
VC
RW/ROM
VOFST
27 VC
VC
LD
1
PD
2
EQ IN
3
EQ
26 RFC
25 VFC
24 BST
RFAC
VCA
23 RFG
VCC
22 VCC
APC AMP
EQ ON/OFF
RW/ROM
AC SUM
GND
RFAC
SUMMING
AMP
4
5
A
A
A
B
C
D
B
C
B
C D
21 CEI
–
+
20 CE
D
DVC
A
B
C
D
6
7
8
9
VOFST
–
+
VC
RW/ROM
19 TE BAL
RW/ROM
E 10
GM
F 11
GM
SW 12
APC-OFF
(Hi-Z)
RW/ROM
(H/L)
–
+
18 TE
VC
RW/ROM
RW/ROM
DVCC 13
B
DVC
DVC 14
D
A
17 FEI
VOFST
–
+
–
+
16 FE
C
DVC
VC
RW/ROM
RFAC 15
27
CDX-T67
IC201
FWD
LA6576L-TE-L
REV
1
2
VCC2
3
VLO–
4
THERMAL SHUT DOWN
INPUT
36
S-GND
CH2-4
MUTE
35
MUTE2
CH1
MUTE
34
MUTE1
33
VIN4
32
VIN4–
31
VIN4+
30
VREF-IN
29
VIN1 (VREF)-SW
28
VREF-OUT (CH1)
27
REG-OUT
26
REG-IN
25
VIN3+
24
VIN3–
23
VIN3
22
VIN2+
21
VIN2–
20
VIN2
19
VIN1+B
OUTPUT
CONTROL
VO4+
6
+
–
5
LEVEL
SHIFT
VO3+
VO3–
+
–
VO4–
+
–
VLO+
7
VIN1/VREF
SWITCH
8
LEVEL
SHIFT
9
5VREG
+
–
–
+
LEVEL
SHIFT
+
–
VO2+ 10
+
–
VO2– 11
VO1+ 12
VO1– 13
VCC1 14
–
+
VIN1 15
+
–
LEVEL
SHIFT
+
–
VIN1–A 16
VIN1+A 17
VIN1–B 18
–
+
AMP-A
–
+
AMP-B
– MAIN Board –
RESET
11
10
9
8
1
2
3
4
5
6
7
BUS ON OUT
BUS ON IN
GND
BUS CLK
VREF
BUS DATA
BUS RESET
RESET
SWITCH
28
CONTROL
1
2
3
4
CONT
DATA IN
12
GND
DATA OUT
13
VIN
CLK OUT
14
NJM2395AF08
VOUT
LINK OFF
IC202
BUS ON
BA8272AFV-E2
VCC
IC201
CDX-T67
IC302
VCC 1
NC 2
LB1930M-TLM
10 NC
BUFFER
IN1 3
MOTOR
DRIVE
CIRCUIT
CONTROL
CIRCUIT
IN2 4
9 OUT1
8 NC
7 OUT2
BUFFER
6 P-GND
S-GND 5
PCO
FILI
FILO
CLTV
AVSS3
RFAC
BIAS
ASYI
ASYO
AVDD0
IGEN
AVSS0
ADIO
RFDC
CE
TE
60
59 58 57
56 55 54 53
52
51 50 49 48
47
46 45
44
43 42 41
DIGITAL
OUT
LRCK 61
PCMD 62
D/A
INTERFACE
INTERNAL BUS
VDD
VSS
AVDD3
CXD3017Q
DOUT
IC401
ERROR
CORRECTOR
DIGITAL
PLL
16K
RAM
40 SE
39 FE
38 VC
ASYMMETRY
CORRECTOR
OPERATIONAL
AMPLIFIER
ANALOG SWITCH
EFM
DEMODULATOR
A/D
CONVERTER
BCK 63
EMPH 64
XVDD 65
66
67
68
69
70
71
TIMING
LOGIC
CLOCK
GENERATOR
SERVO DSP
LOUT1 72
PWM
AVSS1 73
AVSS2 74
LOUT2 75
PWM
3rd ORDER
NOISE SHAPER
OVER SAMPLING
DIGITAL FILTER
AIN2 76
AOUT2 77
AVDD2 78
RMUT 79
LMUT 80
SUBCODE
PROCESSOR
PWM GENERATOR
FOCUS
SERVO
FOCUS PWM
GENERATOR
TRACKING
SERVO
TRACKING
PWM GENERATOR
SLED
SERVO
SLED PWM
GENERATOR
37 XTSL
36 TES1
35 TEST
34 VSS
33
32
31
30
29
28
FRDR
FFDR
TRDR
TFDR
SRDR
SFDR
27 SSTP
SERVO
INTERFACE
SERVO AUTO
SEQUENCER
SERIAL IN
INTERFACE
CPU
INTERFACE
DIGITAL
CLV
26 MDP
25 LOCK
MIRR, DFCT,
FOK
DETECTOR
24 FOK
23 DFCT
22 MIRR
4
5 6 7 8
9 10 11 12 13 14 15 16 17 18 19 20
XRST
SYSM
DATA
XLAT
CLOK
SENS
SCLK
VDD
ATSK
C2PO
SCOR
3
WFCK
XUGF
XPCK
GFS
1 2
SQSO
SQCK
21 COUT
SPOA
SPOB
XLON
XTAI
XTAO
XVSS
AVDD1
AOUT1
AIN1
29
CDX-T67
5-12.
IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC301 MB90473PFV-G-113-BNDE1 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1, 2
RAMA5, RAMA6
O
Address signal output to the S-RAM Not used (open)
3
ELVR
O
Motor drive signal (elevator down direction) output to the elevator motor drive (IC302)
“L” active *1
4
ELVF
O
Motor drive signal (elevator up direction) output to the elevator motor drive (IC302)
“L” active *1
5
LOADF
O
Motor drive signal (load chucking direction) output to the chucking motor drive (IC201)
“L” active *2
6
LOADR
O
Motor drive signal (save direction) output to the chucking motor drive (IC201)
“L” active *2
7, 8
RAMA7, RAMA12
O
Address signal output to the S-RAM Not used (open)
9
VSS
—
Ground terminal
10
RAMA14
O
Address signal output to the S-RAM Not used (open)
11
RAMWE
O
Write enable output to the S-RAM Not used (open)
12 to15
RAMA13, RAMA8,
RAMA9, RAMA11
O
Address signal output to the S-RAM Not used (open)
16
UNI SI
I
Serial data input from the SONY bus interface (IC201)
17
UNI SO
O
Serial data output to the SONY bus interface (IC201)
18
UNI CK
I
Serial data transfer clock signal input from the SONY bus interface (IC201)
19
LEDDAT
O
Not used (open)
20
LEDCLK
O
Not used (open)
21
VCC
—
Power supply terminal
22
LEDLAT
O
Not used (open)
23
CDON
O
Power supply on/off control signal output terminal “H”: power on Not used (open)
24
ELVON
O
Mechanism deck section power supply on/off control signal output “H”: power on
25
RX
I
Input terminal at the flash memory data write mode Not used (open)
26
TX
O
Output terminal at the flash memory data write mode Not used (open)
27
NC
O
Not used (open)
28
EECLK
O
Serial data transfer clock signal output to the EEPROM Not used (open)
29
FL BOOT
I
Flash memory data write control signal input terminal “L” active Not used (fixed at “H”)
30, 31
NC
O
Not used (open)
32
EEDAT
I/O
Two-way data bus with the EEPROM Not used (pull down)
33
AVCC
—
Power supply terminal (for A/D converter)
34
AVRH
I
35
AVSS
—
36
EHS
I
Elevator height position detection signal input from the RV301 (elevator height sensor)
(A/D input)
37
MCK
I
Input of detection signal for the fine adjustment (elevator height (address) adjustment; RV302) of
elevator height position (A/D input)
38, 39
KEY0, KEY1
I
Not used (fixed at “H”)
40
VSS
—
41
FOK
I
Focus OK signal input from the CXD3017Q (IC401) “L”: NG, “H”: OK
42
GFS
I
Guard frame sync signal input from the CXD3017Q (IC401) “L”: NG, “H”: OK
43
SCLK
O
Serial data reading clock signal output to the CXD3017Q (IC401)
44
SENS
I
Internal status signal (sense signal) input from the CXD3017Q (IC401)
45
BUSON
I
Bus on/off control signal input from the SONY bus interface (IC201) “H”: bus on
46
BUCHK
I
Battery detection signal input “L”: battery on
30
Reference voltage input terminal (for A/D converter)
Ground terminal (for A/D converter)
Ground terminal
CDX-T67
Pin No.
Pin Name
I/O
Description
47, 48
MD0, MD1
I
Setting terminal for the CPU operational mode (fixed at “H” in this set)
49
MD2
I
Setting terminal for the CPU operational mode (fixed at “L” in this set)
50
EJECT SW
I
Eject switch (SW303) input terminal “L” active
51
MAGLK SW
I
Magazine in/out detect switch (SW302) input terminal
“L”: magazine in/out operation, “H”: normally
52
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD3017Q (IC401)
53
GRSCOR
I
Subcode sync (S0+S1) detection signal input terminal Not used (open)
54
NC
O
Not used (open)
55
HS
O
Normal/high speed playback control signal output terminal
“L”: high speed playback Not used (open)
56
SQSO
I
Subcode Q data input from the CXD3017Q (IC401)
57
NC
O
Not used (open)
58
SQCK
O
Subcode Q data reading clock signal output to the CXD3017Q (IC401)
59
CDCLK
O
Serial data transfer clock signal output to the CXD3017Q (IC401)
60
CDLAT
O
Serial data latch pulse signal output to the CXD3017Q (IC401)
61
CDDAT
O
Serial data output to the CXD3017Q (IC401)
62
XRST
O
System reset signal output to the CXD3017Q (IC401) “L”: reset
63
XQOK
O
Subcode Q OK pulse signal output terminal Not used (open)
64
XRDE
O
D-RAM read enable signal output terminal Not used (open)
65
XWRE
O
D-RAM write enable signal output terminal Not used (open)
66
EMPH
O
Emphasis control signal output to the CXD3017Q (IC401) “H”: emphasis on
67
MUTE
O
Audio line muting on/off control signal output “H”: muting on
68
RAMA10
O
Address signal output to the S-RAM Not used (open)
69
RAMCS
O
Chip select enable output to the S-RAM Not used (open)
70 to 74
RAMIO7 to
RAMIO3
I/O
Two-way data bus with the S-RAM Not used (open)
75
RESET
I
76
RAMIO2
I/O
Two-way data bus with the S-RAM Not used (open)
77
X1A
O
Sub system clock output terminal Not used (open)
78
X0A
I
Sub system clock input terminal Not used (fixed at “L”)
79
VSS
—
80
X0
I
Main system clock input terminal (4 MHz)
81
X1
O
Main system clock output terminal (4 MHz)
System reset signal input from the SONY bus interface (IC201) and reset signal generator (IC204)
“L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
Ground terminal
82
VCC
—
Power supply terminal
83, 84
RAMIO1, RAMIO0
I/O
Two-way data bus with the S-RAM Not used (open)
O
Address signal output to the S-RAM Not used (open)
85 to 88 RAMA0 to RAMA3
89
SINGLE
I
Setting terminal for the single disc/multiple discs mode
“L”: single disc mode, “H”: multiple discs mode (fixed at “H”)
90
6/10 SEL
I
Setting terminal for the 6 discs changer/10 discs changer model
“L”: 10 discs changer model, “H”: 6 discs changer model (fixed at “H”)
91
CFSEL
I
Custom file on/off setting terminal “L”: custom file on Not used (fixed at “H”)
92
TEXTSEL
I
CD text mode setting terminal
“L”: CD text on, “H”: does not display track name Not used (fixed at “H”)
93
ESPSEL
I
ESP mode setting terminal “L”: ESP on Not used (fixed at “H”)
94
TEST
I
Test on/off setting terminal “L”: test mode Not used (fixed at “H”)
95
MAG SW
I
Magazine detect switch (SW301) input terminal “L”: magazine is set
31
CDX-T67
Pin No.
Pin Name
I/O
Description
96
SAVE SW
I
Chucking end detect switch (SW102) input terminal
“L”: When completion of the disc chucking, loading or save operation
97
LOAD SW
I
Chucking end detect switch (SW102) input terminal
“L”: When completion of the disc chucking, loading or save operation
98
LIM SW
I
Sled limit in detect switch (SW101) input terminal
“L”: When the optical pick-up is inner position
99
RW SEL
O
CD-ROM/RW selection signal output “L”: CD-RW, “H”: CD-ROM
100
RAMA4
O
Address signal output to the S-RAM
Not used (open)
*1 elevator motor (M104) control
Mode
Terminal
STOP
ELEVATOR ELEVATOR
UP
DOWN
BRAKE
ELVF (pin 4)
“L”
“L”
“H”
“H”
ELVR (pin 3)
“L”
“H”
“L”
“H”
STOP
LOAD
CHUCKING
SAVE
BRAKE
LOADF (pin 5)
“L”
“L”
“H”
“H”
LOADR (pin 6)
“L”
“H”
“L”
“H”
*2 chucking motor (M103) control
Mode
Terminal
32
CDX-T67
Ver 1.4
SECTION 6
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
6-1. CASE SECTION
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
#1
4
5
3
#1
1
#1
2
18
13
17
10
MG-276A-159
19
22
16
20
4
#1
23
8
20
6
11
15
7
21
RV301
10
8
9
12
14
13
13
Ref. No.
Part No.
Description
1
2
3
4
5
3-225-801-11
3-225-802-01
X-3379-940-1
3-047-886-11
3-225-798-11
DOOR (S)
BUCKLE (S)
PLATE ASSY, F/P
LEVER (FLT. 838)
CASE (UPPER S)
6
7
8
9
10
X-3379-931-1
X-3379-932-1
3-225-807-01
X-3379-942-1
3-225-808-01
ARM (FLT. S) ASSY
ARM (FRT. S) ASSY
DAMPER (S)
CASE (LOWER. S) ASSY
SPRING (FLT S)
11
12
3-233-247-01 SPACER (BUTTON EJECT)
A-3326-968-A MAIN BOARD, COMPLETE
Remark
Ref. No.
Part No.
Description
Remark
13
14
15
16
17
3-935-636-11
3-225-810-01
3-225-805-01
3-376-464-11
1-757-747-11
SCREW (FP)
BUTTON (S) (EJECT)
ESCUTCHEON (S)
SCREW (+PTT 2.6X6), GROUND POINT
CORD (WITH CONNECTOR) (BUS/RCA)
18
19
20
21
22
1-680-823-11
1-680-828-11
3-233-246-01
3-348-750-01
3-233-248-01
JACK FLEXIBLE BOARD
JACK BOARD
CUSHION (CHASSIS 6T)
CUSHION (DAMPER)
CUSHION (JACK)
23
RV301
3-233-245-01 SPACER (CASE LOWER)
1-227-137-11 RES, VAR, SLIDE 10K
(ELEVATOR HEIGHT SENSOR)
33
CDX-T67
6-2. MECHANISM DECK SECTION-1
(MG-276A-159)
#2
56
elevator assy section
M104
55
not supplied
#8
54
57
#2
#2
53
58
51
Ref. No.
51
52
53
54
55
34
Part No.
Description
A-3315-334-A
3-048-814-01
3-227-131-01
3-973-975-11
3-935-636-11
CHASSIS ASSY, MAIN
SCREW (M1.7X2.2)
BELT (TS)
DAMPER, OIL
SCREW (FP)
52
Remark
Ref. No.
56
57
58
M104
Part No.
Description
3-227-133-01
3-227-150-01
3-701-440-21
A-3315-337-A
BRACKET (MDM)
SPRING, TENSION
WASHER, 3.5
MOTOR ASSY, MD (ELEVATOR)
Remark
CDX-T67
Ver 1.1
6-3. MECHANISM DECK SECTION-2
(MG-276A-159)
#4
106
#6
#4
110
#6
#6
117
109
107
108
105
112
#5
111
113
M101
114
#9
116
104
118
115
103
#3
#7
102
not supplied
#3
not supplied
M103
101
119
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
101
102
103
104
105
X-3380-094-1
3-227-173-01
A-3315-331-A
X-3380-644-1
A-3326-966-A
LEVER (CHK. R) ASSY
JOINT (CHK)
CHASSIS (EV) ASSY
SERVICE ASSY, CHASSIS (OP) BLOCK
RF BOARD, COMPLETE
106
107
108
109
110
111
3-230-917-01
3-227-117-01
3-318-136-01
3-227-120-01
3-227-118-01
X-3380-098-1
HEAT SINK
SPRING (SLED), DETENT
WASHER, POLYETHYLENE, DIA. 1.2
GEAR (SL2)
SPRING (SLED FRONT POINT)
BEARING (SLED) ASSY
Remark
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Ref. No.
Part No.
Description
112
113
0 114
115
116
A-3315-327-A
1-680-824-11
8-820-103-03
X-3380-093-1
3-231-650-01
SHAFT (SLED FEED) ASSY
OP FLEXIBLE BOARD
OPTICAL PICK-UP KSS-720A/K1RP
LEVER (CHK. L) ASSY
SPRING (FOP), LEAF
1-680-822-11
3-233-757-01
3-010-230-01
A-3307-854-A
A-3315-325-A
MAIN FLEXIBLE BOARD
SPACER (TRAY RETAINER)
SPACER (DISC RETAINER L)
MOTOR COMPLETE ASSY, SLED
MOTOR ASSY, LE (CHUCKING)
117
118
119
M101
M103
Remark
35
CDX-T67
Ver 1.1
JACK
SECTION 7
ELECTRICAL PARTS LIST
MAIN
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Ref. No.
Part No.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
Description
Remark
1-680-828-11 JACK BOARD
***********
< CONNECTOR >
CN901
1-770-350-21 CONNECTOR, FPC 13P
< FERRITE BEAD >
FB901
FB902
FB903
1-414-760-21 FERRITE
1-414-760-21 FERRITE
1-414-760-21 FERRITE
0uH
0uH
0uH
< CHIP FUSE >
IC901
1-576-437-21 FUSE, CHIP
**************************************************************
A-3326-968-A MAIN BOARD, COMPLETE
*********************
< CAPACITOR >
C201
C202
C203
C204
C205
1-162-964-11
1-162-968-11
1-164-156-11
1-115-466-00
1-126-382-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.001uF
0.0047uF
0.1uF
1000uF
100uF
10%
10%
20%
20%
50V
50V
25V
16V
16V
C206
C207
C208
C209
C210
1-126-382-11
1-126-382-11
1-107-826-11
1-126-382-11
1-115-466-00
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
100uF
100uF
0.1uF
100uF
1000uF
20%
20%
10%
20%
20%
16V
6.3V
16V
6.3V
16V
C211
C212
C213
C214
C215
1-162-974-11
1-162-974-11
1-165-112-11
1-162-974-11
1-162-974-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.33uF
0.01uF
0.01uF
20%
50V
50V
10V
50V
50V
C216
C217
C301
C302
C303
1-162-974-11
1-164-156-11
1-162-974-11
1-162-974-11
1-124-233-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
0.1uF
0.01uF
0.01uF
10uF
C304
C305
C306
C307
C308
1-162-974-11
1-125-837-11
1-164-156-11
1-162-974-11
1-162-974-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
1uF
0.1uF
0.01uF
0.01uF
36
20%
10%
50V
25V
50V
50V
16V
50V
6.3V
25V
50V
50V
Ref. No.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
When indicating parts by reference
number, please include the board.
Part No.
Description
Remark
C401
C402
C403
C404
C405
1-164-156-11
1-162-974-11
1-162-966-11
1-248-499-11
1-248-499-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.1uF
0.01uF
0.0022uF 10%
220uF
20%
220uF
20%
25V
50V
50V
16V
16V
C407
C408
C410
C411
C412
1-165-176-11
1-162-965-11
1-164-230-11
1-162-970-11
1-125-891-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.0015uF
220PF
0.01uF
0.47uF
10%
10%
5%
10%
10%
16V
50V
50V
25V
10V
C413
C414
C415
C416
C501
1-164-230-11
1-107-826-11
1-164-230-11
1-162-970-11
1-164-217-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.1uF
220PF
0.01uF
150PF
5%
10%
5%
10%
5%
50V
16V
50V
25V
50V
C502
C503
C504
C505
C506
1-164-217-11
1-162-964-11
1-162-964-11
1-164-230-11
1-164-230-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
150PF
0.001uF
0.001uF
220PF
220PF
5%
10%
10%
5%
5%
50V
50V
50V
50V
50V
C508
C509
C510
C511
C512
1-126-779-61
1-126-513-11
1-126-513-11
1-126-791-11
1-126-791-11
ELECT
ELECT
ELECT
ELECT
ELECT
47uF
47uF
47uF
10uF
10uF
20%
20%
20%
20%
20%
4V
4V
4V
16V
16V
C513
C514
C515
C516
1-162-927-11
1-162-927-11
1-126-779-61
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
100PF
100PF
47uF
0.01uF
5%
5%
20%
10%
50V
50V
4V
25V
< CONNECTOR >
CN201
CN202
1-770-350-21 CONNECTOR, FPC 13P
1-793-820-21 CONNECTOR, FPC 22P
< DIODE >
D201
D202
D203
D204
D207
8-719-017-94
8-719-017-94
8-719-421-24
8-719-071-34
8-719-422-56
DIODE
DIODE
DIODE
DIODE
DIODE
MA8180-TX
MA8180-TX
MA8039-H-TX
RB521S-30-TE61
MA8056-H-TX
D209
D210
D212
8-719-988-61 DIODE 1SS355TE-17
8-719-069-56 DIODE UDZSTE-176.2B
8-719-071-34 DIODE RB521S-30-TE61
CDX-T67
Ver 1.1
MAIN
Ref. No.
D213
Part No.
Description
Remark
Ref. No.
RF
Part No.
Description
Remark
R508
R509
R510
R511
R512
1-216-813-11
1-216-845-11
1-216-845-11
1-219-316-11
1-219-310-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
100K
100K
12K
6.8K
5%
5%
5%
2%
2%
1/16W
1/16W
1/16W
1/16W
1/16W
R513
R514
R515
R517
R518
1-219-310-11
1-219-316-11
1-216-833-11
1-219-310-11
1-219-316-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
6.8K
12K
10K
6.8K
12K
2%
2%
5%
2%
2%
1/16W
1/16W
1/16W
1/16W
1/16W
R519
R520
R521
1-219-310-11 METAL CHIP
1-219-316-11 METAL CHIP
1-216-833-11 METAL CHIP
6.8K
12K
10K
2%
2%
5%
1/16W
1/16W
1/16W
8-719-071-34 DIODE RB521S-30-TE61
< IC >
IC201
IC202
IC203
IC204
IC301
8-759-829-46
8-759-833-13
8-759-358-38
8-759-827-97
6-800-420-01
IC
IC
IC
IC
IC
BA8272AFV-E2
NJM2395AF08
NJM78M05DLA (TE1)
XC61CN2502PR
MB90473PFV-G-113-BNDE1
IC302
IC401
IC501
8-759-527-33 IC LB1930M-TLM
8-752-402-31 IC CXD3017Q
8-759-662-11 IC TLV2362IPWR
< TRANSISTOR >
Q202
Q203
Q205
Q206
Q301
8-729-230-49
8-729-230-49
8-729-820-46
8-729-230-49
8-729-901-00
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q501
Q502
Q503
8-729-028-62 TRANSISTOR
8-729-015-39 TRANSISTOR
8-729-015-39 TRANSISTOR
2SC2712-YG-TE85L
2SC2712-YG-TE85L
2SB1202FAST-TL
2SC2712-YG-TE85L
DTC124EKA-T146
< VARIABLE RESISTOR >
RV302
1-223-834-11 RES, ADJ, CARBON 47K
< SWITCH >
DTA115EKA-T146
UN2226-(TX)
UN2226-(TX)
SW301 1-771-540-11 SWITCH, PUSH (1KEY) (MAGAZINE DETECT)
SW302 1-529-566-41 SWITCH, PUSH (1KEY)
(MAGAZINE IN/OUT DETECT)
SW303 1-692-431-21 SWITCH, TACTILE (Z)
< RESISTOR >
R201
R202
R203
R204
R205
1-216-841-11
1-216-813-11
1-216-847-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
220
150K
47K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R206
R207
R209
R211
R301
1-216-846-11
1-216-845-11
1-216-841-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120K
100K
47K
100K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R302
R303
R305
R306
R307
1-216-845-11
1-216-845-11
1-216-845-11
1-216-797-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
10
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R308
R309
R401
R402
R403
1-216-833-11
1-216-821-11
1-216-827-11
1-216-827-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
3.3K
3.3K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R404
R405
R406
R407
R408
1-216-857-11
1-216-833-11
1-216-845-11
1-216-839-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
10K
100K
33K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R410
R412
R414
R501
R502
1-216-845-11
1-216-839-11
1-216-821-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
33K
1K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R503
R504
R505
R506
R507
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
220
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< VIBRATOR >
X301
1-781-282-11 VIBRATOR, CERAMIC (4MHz)
X401
1-760-307-11 VIBRATOR, CERAMIC (16.9344MHz)
**************************************************************
A-3326-966-A RF BOARD, COMPLETE
*******************
< CAPACITOR >
C107
C108
C109
C110
C111
1-126-209-11
1-126-209-11
1-107-826-11
1-126-206-11
1-107-826-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
100uF
100uF
0.1uF
100uF
0.1uF
20%
20%
10%
20%
10%
4V
4V
16V
6.3V
16V
C112
C113
C114
C115
C116
1-107-826-11
1-107-826-11
1-107-826-11
1-126-209-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
100uF
0.1uF
10%
10%
10%
20%
10%
16V
16V
16V
4V
16V
C117
C119
C201
C202
C203
1-107-826-11
1-107-826-11
1-107-778-11
1-164-156-11
1-162-962-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
470uF
0.1uF
470PF
10%
10%
20%
10%
16V
16V
16V
25V
50V
C204
C205
C206
C208
C209
1-162-962-11
1-162-962-11
1-162-962-11
1-164-227-11
1-164-227-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
470PF
470PF
0.022uF
0.022uF
10%
10%
10%
10%
10%
50V
50V
50V
25V
25V
C211
C217
C220
1-164-227-11 CERAMIC CHIP
1-164-156-11 CERAMIC CHIP
1-107-725-11 CERAMIC CHIP
0.022uF
0.1uF
0.1uF
10%
25V
25V
16V
10%
37
CDX-T67
Ver 1.1
RF
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
< CONNECTOR >
CN101
CN102
1-793-820-21 CONNECTOR, FPC 22P
1-815-016-21 CONNECTOR, FFC/FPC (ZIF) 16P
17
18
113
0 114
117
8-752-089-74 IC CXA2581N-T4
8-759-832-99 IC LA6576L-TE-L
M101
M103
M104
RV301
8-729-141-48 TRANSISTOR
8-729-901-00 TRANSISTOR
1-757-747-11
1-680-823-11
1-680-824-11
8-820-103-03
1-680-822-11
CORD (WITH CONNECTOR) (BUS/RCA)
JACK FLEXIBLE BOARD
OP FLEXIBLE BOARD
OPTICAL PICK-UP KSS-720A/K1RP
MAIN FLEXIBLE BOARD
MOTOR COMPLETE ASSY, SLED
MOTOR ASSY, LE (CHUCKING)
MOTOR ASSY, MD (ELEVATOR)
RES, VAR, SLIDE 10K
(ELEVATOR HEIGHT SENSOR)
************************************************************
< TRANSISTOR >
Q101
Q102
Remark
MISCELLANEOUS
**************
< IC >
IC101
IC201
Description
2SB624T1-BV345
DTC124EKA-T146
A-3307-854-A
A-3315-325-A
A-3315-337-A
1-227-137-11
< RESISTOR >
R103
R106
R109
R110
R111
1-216-801-11
1-216-845-11
1-216-845-11
1-216-836-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
100K
100K
18K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R112
R113
R116
R117
R118
1-216-833-11
1-216-835-11
1-216-845-11
1-218-859-11
1-218-879-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
15K
100K
3.3K
22K
5%
5%
5%
0.5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R119
R120
R121
R127
R128
1-218-847-11
1-216-837-11
1-216-837-11
1-216-801-11
1-218-847-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
22K
22K
22
1K
0.5%
5%
5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R201
R202
R203
R204
R205
1-216-833-11
1-216-833-11
1-216-833-11
1-216-839-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
33K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R206
R207
R208
R209
R210
1-216-839-11
1-216-833-11
1-216-839-11
1-216-833-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
10K
33K
10K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R211
R212
R213
R214
R215
1-216-841-11
1-216-843-11
1-216-841-11
1-216-842-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
68K
47K
56K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R216
R218
R219
R220
R222
1-216-839-11
1-216-833-11
1-216-839-11
1-216-834-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
10K
33K
12K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R223
1-216-820-11 METAL CHIP
820
5%
1/16W
**************
HARDWARE LIST
**************
#1
#2
#3
#4
#5
7-685-792-09
7-685-780-09
7-627-552-88
7-628-253-00
7-627-554-07
SCREW +PTT 2.6X6 (S)
SCREW +PTT 2X3 (S)
SCREW, PRECISION +P 1.7X2.2
SCREW +PS 2X4
SCREW, PRECISION +P 2X2.2
#6
7-627-553-37 PRECISION SCREW +P 2X3 TYPE 3
#7
7-624-104-04 STOP RING 2.0, TYPE -E
#8
7-685-851-09 SCREW, +BVTT 2X4 (S)
#9
7-627-554-38 SCREW, PRECISION +P 2X1.8 TYPE 1
************************************************************
ACCESSORIES & PACKING MATERIALS
*******************************
3-228-436-11 MANUAL, INSTRUCTION (ENGLISH, FRENCH,
SPANISH, TRADITIONAL CHINESE)
3-228-436-21 MANUAL, INSTRUCTION (ENGLISH, FRENCH,
GERMAN, DUTCH, ITALIAN)
3-228-436-31 MANUAL, INSTRUCTION (SPANISH, SWEDISH,
PORTUGUESE, POLISH, RUSSIAN, GREEK)
A-3315-335-A MAGAZINE (276) ASSY
************************************************************
< SWITCH >
SW101 1-571-754-31 SWITCH, PUSH (1KEY) (LIMIT)
SW102 1-786-149-21 SWITCH, PUSH (1KEY)
(CHUCKING END DETECT)
**************************************************************
38
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
CDX-T67
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
PARTS FOR INSTALLATION AND CONNECTIONS
**************************************
501
* 502
503
504
3-225-809-01
X-3369-824-1
1-590-519-21
1-590-874-11
BRACKET (S)
SCREW ASSY
CORD (WITH CONNECTOR) (BUS CABLE 5m)
CORD, CONNECTION (RCA PIN CORD 5m)
501
502
BRACKET (S)
×2
+PSW4 × 10
×4
TAPPING SCREW
(DIA.5 × 20) × 4
SCREW ASSY
503
504
BUS CABLE 5 m
×1
RCA PIN CORD 5 m
×1
39
CDX-T67
MEMO
40
CDX-T67
US Model
Canadian Model
AEP Model
UK Model
E Model
SERVICE MANUAL
Ver 1.2 2001.06
SUPPLEMENT-1
File this supplement with the service manual.
Subject: Change of MAIN/JACK/RF boards. (Suffix-12)
(ECN-CSA04865/CSB02866)
In this set, RF, MAIN and JACK boards have been changed in the midway of production.
Printed wiring boards and schematic diagrams of new type, and changed
parts list are described in this supplement-1.
Refer to original service manual for other information.
TABLE OF CONTENTS
1.
NEW/FORMER TYPE DISCRIMINATION ..... 2
2.
DIAGRAMS
2-1. Note for Printed Wiring Boards and
Schematic Diagrams .......................................................
2-2. Printed Wiring Boards – RF Board – ............................
2-3. Schematic Diagram – RF Board – .................................
2-4. Printed Wiring Boards
– MAIN Board (Component Side) – ..............................
2-5. Printed Wiring Board
– MAIN Board (Conductor Side) – ................................
2-6. Schematic Diagram – MAIN Board (1/2) – ..................
2-7. Schematic Diagram – MAIN Board (2/2) – ..................
2-8. Printed Wiring Boards – JACK Board – ........................
2-9. Schematic Diagram – JACK Board – .............................
3.
3
4
5
6
7
8
9
10
10
ELECTRICAL PARTS LIST ............................... 11
CDX-T67
1. NEW/FORMER TYPE DISCRIMINATION
– JACK BOARD (Conductor Side) –
– RF BOARD (Component Side) –
Former Type : 1-680-828-11
New Type : 1-680-828-12
Former Type : 1-680-829-11
New Type : 1-680-829-12
– MAIN BOARD (Component Side) –
Former Type : 1-680-827-11
New Type : 1-680-827-12
2
CDX-T67
2. DIAGRAMS
2-1.
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
f
: internal component.
•
: Pattern from the side which enables seeing.
•
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
•
: internal component.
• C : panel designation.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce por tant le numéro
spécifié.
• A : B+ Line.
• H : adjustment for repair.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from CD changer controller.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : CD PLAY
3
3
CDX-T67
2-2.
PRINTED WIRING BOARDS – RF Board –
2
1
3
4
5
6
7
8
9
10
RF BOARD (COMPONENT SIDE)
A
11
12
13
14
RF BOARD (CONDUCTOR SIDE)
RED
M
(CHASSIS)
M101
(SLED)
BLK
CN101
OP FLEXIBLE
BOARD
B
R121
C119
R120
C114
R106
C
MAIN
BOARD
CN202
TP
(TE)
A
(Page 6)
16
CN102
C110
R109
IC101
R117
TP
(RFAC)
C117
1
C116
MAIN
FLEXIBLE
BOARD
OPTICAL
PICK-UP
BLOCK
KSS-720A
C109
C112
SW101
(LIMIT)
C113
TP
(VC)
D
R118
C111
R128
R113
R116
R119
R111
R112
Q101
R110
Q102
C115
R103 R127
C108
E
R218 C211
R214 R213
R220
M102
(SPINDLE)
R212
R209
R210
R215
C107
C209
R211
R223
R222
M
R216
R219
C208
C202
C206
R207
F
R208
C205
BLK
RED
R205
R206
IC201
C204
R203
C203
R204
R202
C217 R201
G
12
1-680-829-
C201
(12)
C220
SW102
12
RED
BLK
H
1-680-829-
M
M103
(CHUCKING)
• Semiconductor
Location
Ref. No.
Location
IC101
IC201
C-5
F-6
Q101
Q102
D-6
E-5
SW102
(CHUCKING END DETECT)
4
4
(12)
CDX-T67
2-3.
SCHEMATIC DIAGRAM – RF Board –
Q101
2SB624T1-BV345
C111
0.1
AUTOMATIC
POWER CONTROL
R127
22
R119
1k
C110
100
6.3V
RF AMP,
FOCUS/TRACKING
R103
22
C107
100
4V
ERROR AMP
R118
22k
DC_
LD
OFST
PD
C116
0.1
R128
1k
R117 3.3k
RFDCI
EQ_
16
RFDCO
IN
C112
0.1
C113 0.1
AC_SUM
CN102
16P
F(-)
VC
GND
RFC
R116
100k
A
VFC
R115
15k
2-AXIS
DEVICE
(FOCUS)
(TRACKING)
DETECTOR
T(-)
B
BST
T(+)
C
RFG
F(+)
D
VCC
E
CEI
R113
12k
R120 22k
VCC
LASER DIODE
VC
F
F
CE
VCC
SW
VC
DVCC
VR
DVC
PD
RFAC
CONTROL SWITCH
R111
10k
R121 22k
E
Q102
DTC124EKA
-T146
RF AMP OFFSET
R114
10k
R109
100k
R110
18k
R112
10k
TE_BAL
TE
R106 100k
PD
I-V
FEI
SW101
AMP
LD
C117
0.1
LD
C115
100
4V
GND
(LIMIT)
FE
ON:WHEN THE OPTICAL PICK-UP IS
C114
0.1
C119
0.1
INNER POSITION
IC101
CXA2581N-T4
SW102
A
(CHUCKING END DETECT)
C
OP
FLEXIBLE
BOARD
ON:WHEN COMPLETION OF THE DISC
CHUCKING OPERATION
B
D
CN101
22P
1
R/RW_SEL
SW101
LIM_SW
SW102
SAVE_SW
TP(RFAC)
RFAC
RFDC
C108
100
4V
TP(VC)
C109
0.1
VC
TP(TE)
TE
FE
DVCC(3V)
GND(5V)
5V
AA1
FRDR
AA2
FFDR
AA3
TRDR
AA4
TFDR
AA5
MDP
AA6
SRDR
FOCUS/TRACKING COIL DRIVE
AA7
SPINDLE/SLED/CHUCKING
MOTOR DRIVE
IC201
LA6576L-TE
(Page 9)
MAIN
FLEXIBLE
BOARD
C202
0.1
C201
470
16V
SFDR
R201
10k
R202
10k
C217
0.1
LOADR
LOADF
GND(8V)
FWD
S-GND
REV
MUTE2
VCC2
MUTE1
8V
TP1
M103
C220
0.1
VL0-
C203
470p
VIN4
TP2
(CHUCKING)
VL0+
VIN4-
VO4+
VIN4+
R203
10k
R204
33k
AA3
AA4
VO4-
C204
470p
VREF-IN
VO3+
VIN1-SW
VO3-
VREF-OUT
R205
10k
R206
33k
R222
1k
R223
820
TP3
M102
C205
470p
TP4
(SPINDLE)
R207
10k
R208
33k
AA2
AA1
VO2+
REG-OUT
VO2-
REG-IN
VO1+
VIN3+
VO1-
VIN3-
C206
470p
TP6
M101
R209
10k
R210
33k
TP5
(SLED)
VCC1
VIN3
VIN1
VIN2+
VIN1-A
VIN2-
R211
47k
R212
68k
R220
12k
AA5
VIN1+A
VIN1-B
C208
0.022
VIN2
R213
47k
R214
56k
VIN1+B
C211
0.022
R218
10k
R219
33k
C209
0.022
R215
10k
R216
33k
AA7
AA6
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
5
5
Les composants identifiés par une marque 0 sont
critiques pour la sécurité. Ne les remplacer que
par une pièce portant le numéro spécifié.
CDX-T67
2-4.
• Semiconductor
Location
2
3
4
5
6
7
8
9
10
Location
D201
D202
D203
D204
D207
D209
D210
D212
D213
G-7
G-7
B-5
G-6
F-7
F-6
F-6
G-9
G-7
IC201
IC203
IC204
IC301
IC302
IC401
IC501
G-6
B-10
E-6
D-7
E-4
C-4
G-4
Q202
Q203
Q205
Q206
Q301
Q501
Q502
Q503
1
B-5
F-5
E-9
F-7
E-3
F-5
H-6
H-6
A
MAIN BOARD (COMPONENT SIDE)
C306
2
C305
D203
B
C203
R412
21
40
1
R202
R307
C414
C413
R405
C
R303
IC401
R408
R302
C403
R410
R305
Q202
20
41
R407
C416
IC203
R308
C415
50
IC301
3
C215
26
25
51
C411
R406
C412
C214
C410
R404
C408
D
C401
60
R403
R414
1
R401
C407
C402 61
100
R301
R402
CN202
1
75
C302
76
R306
C301
R506
Q301
R505
R309
E
R501
R502
C502
C504
C501
R504
C503
R503
100
IC204
Ref. No.
PRINTED WIRING BOARDS – MAIN Board (Component Side) –
C211
C304
Q205
C212
F
MAIN
FLEXIBLE
BOARD
C307
R205
D209
C308
C213
R206
IC302
C208
D210
R211
R203
R209
R204
D207
Q203
A
RF BOARD
CN101
R517
R515
R514
IC201R201
R518
R513
R512
SW302
C202
Q501
C506
(Page 4)
G
Q206
R207
D201
1
IC501
CN201
13
D213
C516
C216
D202
R520
R511
C505
D212
C514
R519
C201 D204
Q502
C217
SW302
MAGAZINE
IN/OUT
DETECT
12
1-680-827-
R508
C513 R510
H
R507
R521
JACK FLEXIBLE
BOARD
Q503
R509
B
JACK BOARD
CN901
(Page 10)
6
6
(12)
2-5.
PRINTED WIRING BOARD – MAIN Board (Conductor Side) –
1
2
3
CDX-T67
4
5
6
7
8
9
10
• Semiconductor
Location
Ref. No.
MAIN BOARD (CONDUCTOR SIDE)
A
IC202
SW303
Z
B
RV301
EVEVATOR HEIGHT
SENSOR
(CHASSIS)
C303
C206
C205
C207
RV302
C
C204
D
C404
IC202
X401
C405
E
X301
C209
SW301
MAGAZINE
DETECT
F
(CHASSIS)
C210
C508
G
(CHASSIS)
C511
RED
C510
M
C512
BLK
C509
H
C515
12
1-680-827-
7
7
(12)
M104
(EVEVATOR)
Location
D-2
CDX-T67
SCHEMATIC DIAGRAM – MAIN Board (1/2) –
1
IC201
BA8272AFV-E2
CN201
13P
BUSON
CLK
2
SCK
Q301
DTC124EKA
SCK
SI
CLK
VREF
SO
DATA
DATA
SI
CD-ROM/RW
SO
SAVE_SW
BUSON
SELECT
SWITCH
BP5
BP6
BP10
SW301
C302
0.01
(FOR SONY BUS)
C202
4700p
I
C208
0.1
O
G
R209
47k
X1A
X0A
X0
VSS
X1
VCC
RAMIO1
RAMA0
RAMIO0
RAMA1
RAMA2
RAMA3
SINGLE
CFSEL
TEXTSEL
TEST
ESPSEL
6/10 SEL
GENERATOR
IC204
XC61CN2502PR
Q205,206
REGULATOR
MAG SW
RAMA5
SAVE SW
RESET SIGNAL
LIM SW
RAMA4
R205
47k
LOAD SW
C216
0.01
Q206
2SC2712-YG
D207
MA8056-H
X301
4MHz
C301
0.01
BUS INTERFACE
Q205
2SB1202FAST-TL
R204
47k
BP7
RESET
RW SEL
GND
D202 MA8180-TX
GND
D212 RB521S-30-TE61
GND
D204 RB521S-30-TE61
B.UP
C201
0.001
RAMIO2
R301
1k
RESET
RAMA6
RAMIO3
ELVR
RAMIO4
ELVF
RAMIO5
LOADF
RAMIO6
LOADR
RAMIO7
LOADF
3
LOADR
R211
100k
C209
100
6.3V
C210
1000
16V
RAMA7
C211
0.01
C212
0.01
RAMCS
RAMA12
RAMA10
VSS
MUTE
RAMA14
EMPH
RAMWE
XWRE
RAMA13
XRDE
EMPH
C206 100
4
16V
C204
1000
16V
IC202
NJM2395AF08
CONT
I
+5V REGULATOR
GND
G
O
RAMA8
VIN
SYSTEM CONTROLLER
XQOK
XRST
IC301
MB90473PFV-G
-113-BNDE1
RAMA9
VOUT
RAMA11
C214
0.01
C215
0.01
DATA
XLAT
UNI SI
CDLAT
UNI SO
CDCLK
UNI CK
SQCK
CLOK
SO
+8V REGULATOR
(Page 9)
XRST
CDDAT
SI
IC203
NJM78M05DL
SQCK
SCK
C207 100 6.3V
D203
MA8039-H-TX
R202 220
LEDDAT
NC
LEDCLK
SQSO
SQSO
C205
100
16V
VCC
C203
0.1
HS
LEDLAT
NC
CDON
ELVON
MD2
MD1
MD0
BUCHK
BUSON
SENS
SCLK
GFS
FOK
VSS
KEY1
KEY0
MCK
EHS
AVSS
AVRH
EEDAT
AVCC
5
MAGLK SW
EJECT SW
C308
0.01
SW302
MAGAZINE
R203
150k
SENS
6
SW303
D210
UDZS-TE17
-6.2B
D209
1SS355TE
-17
C213
0.33
BUSON
C305
1
SCLK
R207
100k
GFS
ELEVATOR
MOTOR DRIVE
FOK
IN/OUT DETECT
R307 10k
BP11
NC
BP12
M104
(ELEVATOR)
R302
100k
SCOR
RX
NC
C304
0.01
FL BOOT
LB1930M-TL
EECLK
IC302
C307
0.01
NC
+3V REGULATOR
GRSCOR
SCOR
Q202
2SC2712-Y
TX
JACK
FLEXIBLE
BOARD
B.UP
D213
RB521S-30-TE61
(Page 10)
DETECT
R201
47k
B.UP
R309
1k
MAGAZINE
BP9
RST
RST
SW301
BP8
C217 0.1
AGND
LIM_SW
RCH
BUSON
VCC
OUT
BUSON BUSON
IN
OUT
GND
LOF
LCH
D201 MA8180-TX
2-6.
R305
100k
Q203
2SC2712-YG
R206
120k
R308
10k
7
R303
100k
8
RV301
BATTERY
ELEVATOR HEIGHT
CHECK
SENSOR
RV301
10k
RV302
47k
C303
10
16V
9
10
11
12
8
8
CDX-T67
2-7.
SCHEMATIC DIAGRAM – MAIN Board (2/2) –
1
2
R501
10k
R306
10
R502
10k
R503
10k
R504
10k
C501
150p
C502
150p
EMPH
C503
0.001
C504
0.001
R505
10k
R506
10k
R509
100k
C513
100p
C505
220p
PCMD
BCK
EMPH
XTAI
XTAO
XVSS
AVDD1
AIN1
AOUT1
LOUT1
AIN2
AVSS1
AVSS2
C401
0.1
3
SQSO
LOUT2
SQSO
AOUT2
LMUT
R519
6.8k
RMUT
R520
12k
C512
10
16V
AVDD2
C404
220
16V
XVDD
X401
16.9344MHz
C405
220
16V
R507
470
C402
0.01
LRCK
DOUT
SQCK
SQCK
XRST
VDD
R414 1k
XRST
VSS
SYSM
AVDD3
R401 3.3k
DATA
Q503
UN2226
MUTING
DATA
R511
12k
C515
47
4V
PCO
XLAT
R512
6.8k
R402
3.3k
XLAT
FILI
CLOK
FILO
SENS
CLTV
CLOK
C407
0.047
R403
10k
SENS
4
R521
10k
SCLK
SCLK
(Page 8)
R404
1M
AVSS3
VDD
RFAC
DIGITAL SIGNAL PROCESSOR,
DIGITAL SERVO PROCESSOR,
ATSK
BIAS
DIGITAL FILTER,D/A CONVERTER
SPOA
VCC
C410
220p
ASYI
IC401
CXD3017Q
SPOB
XLON
AVDD0
WFCK
IGEN
LIM_SW
SAVE_SW
ADIO
RFAC
GFS
RFDC
RFDC
SAVE_SW
VC
TE
R408
33k
C413
220p
SE
FE
VC
XTSL
TES1
TEST
FFDR
TFDR
SFDR
SSTP
MDP
VSS
TE
FRDR
SCOR
TRDR
CE
SRDR
C2PO
COUT
R508
470
R/RW_SEL
LIM_SW
C412
0.47
XPCK
LOCK
5
C411
0.01
TP403
TP404
R510
100k
C416
0.01
C403
2200p
AVSS0
FOK
SCOR
R406
100k
XUGF
DFCT
GND
GFS
R405
10k
TP402
MIRR
MUTING
100p
Q502
UN2226
TP401
C514
IC501
TLV2362IPW
CN202
22P
ASYO
R407 33k
GROUND-ISOLATION
C408
1500p
FE
DVCC(3V)
C511
10
16V
GND(5V)
R518
12k
R513
6.8k
5V
FRDR
Q501
DTA115EKA-T146
FRDR
FFDR
MUTING CONTROL
FFDR
TRDR
R517
6.8k
TRDR
R514
12k
C414
0.1
TP408
TP405
R515
10k
TP407
C506
220p
TP406
SWITCH
R410
100k
TFDR
MDP
MDP
SRDR
SRDR
SFDR
C509
47
4V
SFDR
FRDR
FFDR
TRDR
TFDR
SRDR
C415
220p
SFDR
LIM_SW
C510
47
4V
MDP
6
C516
0.01
FOK
C508
47
4V
R412
33k
LOADR
LOADR
LOADF
LOADF
GND(8V)
7
8V
C306
0.1
8
(CHASSIS)
9
10
11
12
9
9
(Page 5)
TFDR
MAIN
FLEXIBLE
BOARD
CDX-T67
2-8.
PRINTED WIRING BOARDS – JACK Board –
2-9.
SCHEMATIC DIAGRAM – JACK Board –
CN902
10P
CN901
13P
FB901
(L)
JACK BOARD
LCH
LCH
FB902
AGND
AGND
FB903
(R)
(COMPONENT SIDE)
RCH
RCH
BUSON
BUSON
CLK
CLK
DATA
DATA
RST
RST
(FOR SONY BUS)
B.UP
GND
GND
B.UP
IC901
B.UP
B.UP
GND
GND
GND
(CHASSIS)
12
1-680-828-
(12)
(FOR SONY BUS)
6
3
(R)
(L)
7
8
JACK BOARD
4
5
2
1
(CONDUCTOR SIDE)
10
IC901
1
FB901
FB903
CN902
FB902
CN901
13
12
1-680-828-
(12)
JACK FLEXIBLE
BOARD
B
(CHASSIS)
MAIN BOARD
CN201
(Page 6)
10
10
(Page 8)
JACK
FLEXIBLE
BOARD
CDX-T67
JACK
MAIN
3. ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Ref. No.
Part No.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
Description
Remark
1-680-828-12 JACK BOARD
***********
< CONNECTOR >
CN901
1-770-350-21 CONNECTOR, FPC 13P
< FERRITE BEAD >
FB901
FB902
FB903
1-414-760-21 FERRITE
1-414-760-21 FERRITE
1-414-760-21 FERRITE
0uH
0uH
0uH
< CHIP FUSE >
IC901
1-576-437-21 FUSE, CHIP
**************************************************************
A-3326-968-A MAIN BOARD, COMPLETE
*********************
< CAPACITOR >
C201
C202
C203
C204
C205
1-162-964-11
1-162-968-11
1-164-156-11
1-115-466-00
1-126-382-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.001uF
0.0047uF
0.1uF
1000uF
100uF
10%
10%
20%
20%
50V
50V
25V
16V
16V
C206
C207
C208
C209
C210
1-126-382-11
1-126-382-11
1-107-826-11
1-126-382-11
1-115-466-00
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
100uF
100uF
0.1uF
100uF
1000uF
20%
20%
10%
20%
20%
16V
6.3V
16V
6.3V
16V
C211
C212
C213
C214
C215
1-162-974-11
1-162-974-11
1-165-112-11
1-162-974-11
1-162-974-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.33uF
0.01uF
0.01uF
20%
50V
50V
10V
50V
50V
C216
C217
C301
C302
C303
1-162-974-11
1-164-156-11
1-162-974-11
1-162-974-11
1-126-791-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
0.1uF
0.01uF
0.01uF
10uF
C304
C305
C306
C307
C308
1-162-974-11
1-125-837-11
1-164-156-11
1-162-974-11
1-162-974-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
1uF
0.1uF
0.01uF
0.01uF
20%
10%
50V
25V
50V
50V
16V
50V
6.3V
25V
50V
50V
Ref. No.
When indicating parts by reference
number, please include the board.
Part No.
Description
Remark
C401
C402
C403
C404
C405
1-164-156-11
1-162-974-11
1-162-966-11
1-128-499-11
1-128-499-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.1uF
0.01uF
0.0022uF 10%
220uF
20%
220uF
20%
25V
50V
50V
16V
16V
C407
C408
C410
C411
C412
1-165-176-11
1-162-965-11
1-164-230-11
1-162-970-11
1-125-891-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.0015uF
220PF
0.01uF
0.47uF
10%
10%
5%
10%
10%
16V
50V
50V
25V
10V
C413
C414
C415
C416
C501
1-164-230-11
1-107-826-11
1-164-230-11
1-162-970-11
1-164-217-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.1uF
220PF
0.01uF
150PF
5%
10%
5%
10%
5%
50V
16V
50V
25V
50V
C502
C503
C504
C505
C506
1-164-217-11
1-162-964-11
1-162-964-11
1-164-230-11
1-164-230-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
150PF
0.001uF
0.001uF
220PF
220PF
5%
10%
10%
5%
5%
50V
50V
50V
50V
50V
C508
C509
C510
C511
C512
1-126-513-11
1-126-513-11
1-126-513-11
1-126-791-11
1-126-791-11
ELECT
ELECT
ELECT
ELECT
ELECT
47uF
47uF
47uF
10uF
10uF
20%
20%
20%
20%
20%
4V
4V
4V
16V
16V
C513
C514
C515
C516
1-162-927-11
1-162-927-11
1-126-513-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
100PF
100PF
47uF
0.01uF
5%
5%
20%
10%
50V
50V
4V
25V
< CONNECTOR >
CN201
CN202
1-770-350-21 CONNECTOR, FPC 13P
1-793-820-21 CONNECTOR, FPC 22P
< DIODE >
D201
D202
D203
D204
D207
8-719-017-94
8-719-017-94
8-719-421-24
8-719-071-34
8-719-977-03
DIODE
DIODE
DIODE
DIODE
DIODE
MA8180-TX
MA8180-TX
MA8039-H-TX
RB521S-30-TE61
DTZ5.6B
D209
D210
D212
8-719-988-61 DIODE 1SS355TE-17
8-719-069-56 DIODE UDZSTE-176.2B
8-719-071-34 DIODE RB521S-30-TE61
11
CDX-T67
MAIN
Ref. No.
D213
RF
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
R508
R509
R510
R511
R512
1-216-817-11
1-216-845-11
1-216-845-11
1-219-316-11
1-218-867-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
470
100K
100K
12K
6.8K
5%
5%
5%
2%
2%
1/16W
1/16W
1/16W
1/16W
1/16W
R513
R514
R515
R517
R518
1-218-867-11
1-219-316-11
1-216-833-11
1-218-867-11
1-219-316-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
6.8K
12K
10K
6.8K
12K
2%
2%
5%
2%
2%
1/16W
1/16W
1/16W
1/16W
1/16W
R519
R520
R521
1-218-867-11 RES-CHIP
1-219-316-11 RES-CHIP
1-216-833-11 METAL CHIP
6.8K
12K
10K
2%
2%
5%
1/16W
1/16W
1/16W
8-719-071-34 DIODE RB521S-30-TE61
< IC >
IC201
IC202
IC203
IC204
IC301
8-759-829-46
8-759-833-13
8-759-358-38
8-759-827-97
6-800-420-01
IC
IC
IC
IC
IC
BA8272AFV-E2
NJM2395AF08
NJM78M05DLA (TE1)
XC61CN2502PR
MB90473PFV-G-113-BNDE1
IC302
IC401
IC501
8-759-527-33 IC LB1930M-TLM
8-752-402-31 IC CXD3017Q
8-759-662-11 IC TLV2362IPWR
< TRANSISTOR >
Q202
Q203
Q205
Q206
Q301
8-729-200-13
8-729-230-49
8-729-820-46
8-729-230-49
8-729-901-00
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q501
Q502
Q503
8-729-028-62 TRANSISTOR
8-729-015-39 TRANSISTOR
8-729-015-39 TRANSISTOR
2SC2712-Y
2SC2712-YG-TE85L
2SB1202FAST-TL
2SC2712-YG-TE85L
DTC124EKA-T146
< VARIABLE RESISTOR >
RV302
1-223-834-11 RES, ADJ, CARBON 47K
< SWITCH >
DTA115EKA-T146
UN2226-(TX)
UN2226-(TX)
SW301 1-771-540-11 SWITCH, PUSH (1KEY) (MAGAZINE DETECT)
SW302 1-529-566-31 SWITCH, PUSH (1KEY)
(MAGAZINE IN/OUT DETECT)
SW303 1-692-431-21 SWITCH, TACTILE (Z)
< RESISTOR >
R201
R202
R203
R204
R205
1-216-841-11
1-216-813-11
1-216-847-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
220
150K
47K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R206
R207
R209
R211
R301
1-216-846-11
1-216-845-11
1-216-841-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120K
100K
47K
100K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R302
R303
R305
R306
R307
1-216-845-11
1-216-845-11
1-216-845-11
1-216-797-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
10
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R308
R309
R401
R402
R403
1-216-833-11
1-216-821-11
1-216-827-11
1-216-827-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
3.3K
3.3K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R404
R405
R406
R407
R408
1-216-857-11
1-216-833-11
1-216-845-11
1-216-839-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
10K
100K
33K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R410
R412
R414
R501
R502
1-216-845-11
1-216-839-11
1-216-821-11
1-216-833-11
1-218-871-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
100K
33K
1K
10K
10K
5%
5%
5%
5%
2%
1/16W
1/16W
1/16W
1/16W
1/16W
R503
R504
R505
R506
R507
1-218-871-11
1-218-871-11
1-218-871-11
1-218-871-11
1-216-817-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
10K
10K
10K
10K
470
2%
2%
2%
2%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
12
< VIBRATOR >
X301
1-781-282-11 VIBRATOR, CERAMIC (4MHz)
X401
1-760-307-11 VIBRATOR, CERAMIC (16.9344MHz)
**************************************************************
A-3326-966-A RF BOARD, COMPLETE
*******************
< CAPACITOR >
C107
C108
C109
C110
C111
1-126-209-11
1-126-209-11
1-107-826-11
1-126-206-11
1-107-826-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
100uF
100uF
0.1uF
100uF
0.1uF
20%
20%
10%
20%
10%
4V
4V
16V
6.3V
16V
C112
C113
C114
C115
C116
1-107-826-11
1-107-826-11
1-107-826-11
1-126-209-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
100uF
0.1uF
10%
10%
10%
20%
10%
16V
16V
16V
4V
16V
C117
C119
C201
C202
C203
1-107-826-11
1-107-826-11
1-107-778-11
1-164-156-11
1-162-962-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
470uF
0.1uF
470PF
10%
10%
20%
10%
16V
16V
16V
25V
50V
C204
C205
C206
C208
C209
1-162-962-11
1-162-962-11
1-162-962-11
1-164-227-11
1-164-227-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
470PF
470PF
0.022uF
0.022uF
10%
10%
10%
10%
10%
50V
50V
50V
25V
25V
C211
C217
C220
1-164-227-11 CERAMIC CHIP
1-164-156-11 CERAMIC CHIP
1-107-725-11 CERAMIC CHIP
0.022uF
0.1uF
0.1uF
10%
25V
25V
16V
10%
CDX-T67
RF
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
< CONNECTOR >
CN101
CN102
1-793-820-21 CONNECTOR, FPC 22P
1-815-016-21 CONNECTOR, FFC/FPC (ZIF) 16P
< IC >
IC101
IC201
8-752-089-74 IC CXA2581N-T4
8-759-832-99 IC LA6576L-TE-L
< TRANSISTOR >
Q101
Q102
8-729-141-48 TRANSISTOR
8-729-901-00 TRANSISTOR
2SB624T1-BV345
DTC124EKA-T146
< RESISTOR >
R103
R106
R109
R110
R111
1-216-801-11
1-216-845-11
1-216-845-11
1-216-836-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
100K
100K
18K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R112
R113
R114
R115
R116
1-216-833-11
1-216-834-11
1-216-833-11
1-216-835-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
12K
10K
15K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R117
R118
R119
R120
R121
1-218-859-11
1-218-879-11
1-218-847-11
1-216-837-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
22K
1K
22K
22K
0.5%
0.5%
0.5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R127
R128
R201
R202
R203
1-216-801-11
1-218-847-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
1K
10K
10K
10K
5%
0.5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R204
R205
R206
R207
R208
1-216-839-11
1-216-833-11
1-216-839-11
1-216-833-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
10K
33K
10K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R209
R210
R211
R212
R213
1-216-833-11
1-216-839-11
1-216-841-11
1-216-843-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
33K
47K
68K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R214
R215
R216
R218
R219
1-216-842-11
1-216-833-11
1-216-839-11
1-216-833-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
56K
10K
33K
10K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R220
R222
R223
1-216-834-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-820-11 METAL CHIP
12K
1K
820
5%
5%
5%
1/16W
1/16W
1/16W
< SWITCH >
SW101 1-571-754-31 SWITCH, PUSH (1KEY) (LIMIT)
SW102 1-786-149-21 SWITCH, PUSH (1KEY)
(CHUCKING END DETECT)
13
CDX-T67
MEMO
14
CDX-T67
US Model
Canadian Model
AEP Model
UK Model
E Model
SERVICE MANUAL
Ver 1.3 2001.09
SUPPLEMENT-2
Subject: Change of MAIN/JACK boards. (Suffix-13)
(ECN-CSB03047)
In this set, MAIN and JACK boards have been changed in the midway
of production.
Printed wiring boards and schematic diagrams of new type, and changed
parts list are described in this supplement-2.
Refer to original service manual for other information.
• NEW/FORMER TYPE DISCRIMINATION
– JACK BOARD (Conductor Side) –
Former Type : 1-680-828-12
New Type : 1-680-828-13
Former Type : 1-680-827-12
New Type : 1-680-827-13
• DIAGRAMS
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
f
: internal component.
•
: Pattern from the side which enables seeing.
•
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
•
: internal component.
• C : panel designation.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce por tant le numéro
spécifié.
• A : B+ Line.
• H : adjustment for repair.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from CD changer controller.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : CD PLAY
File this supplement with the service manual.
– MAIN BOARD (Component Side) –
CDX-T67
CDX-T67
PRINTED WIRING BOARDS – MAIN Board (Component Side) –
• Semiconductor
Location
3
4
5
6
7
8
9
10
Location
D201
D202
D203
D204
D207
D209
D210
D212
D213
G-7
G-7
B-5
G-6
F-7
F-6
F-6
G-9
G-7
IC201
IC203
IC204
IC301
IC302
IC401
IC501
G-6
B-10
E-6
D-7
E-4
C-4
G-4
Q202
Q203
Q205
Q206
Q301
Q501
Q502
Q503
2
B-5
F-5
E-9
F-7
E-3
F-5
H-6
H-6
A
MAIN BOARD (COMPONENT SIDE)
C306
2
C305
D203
B
C203
R412
1
R202
21
40
R307
C414
C413
R405
C
R303
IC401
R408
R302
C403
R410
R305
Q202
20
41
R407
C416
IC203
R308
C415
50
IC301
3
C215
26
25
51
C411
R406
C412
C214
C410
R404
C408
D
C401
60
R403
R414
1
R401
C407
C402 61
100
R301
R402
CN202
1
75
C302
76
R306
C301
R506
Q301
R505
R309
E
R501
R502
C502
C504
C501
R504
C503
R503
100
IC204
Ref. No.
1
C211
C304
Q205
C212
F
MAIN
FLEXIBLE
BOARD
C307
R205
D209
C308
C213
R206
IC302
C208
D210
R211
R203
R209
R204
D207
Q203
A
RF BOARD
CN101
R517
R515
R514
IC201R201
R518
R513
R512
SW302
C202
Q501
C506
G
Q206
R207
D201
1
IC501
CN201
13
D213
C516
C216
D202
R520
R511
C505
D212
C514
R519
C201 D204
Q502
C217
SW302
MAGAZINE
IN/OUT
DETECT
13
1-680-827-
R508
C513 R510
H
R521
R507
JACK FLEXIBLE
BOARD
Q503
R509
B
JACK BOARD
CN901
(Page 6)
2
2
(13)
CDX-T67
PRINTED WIRING BOARD – MAIN Board (Conductor Side) –
1
2
3
4
5
6
7
8
9
10
• Semiconductor
Location
Ref. No.
MAIN BOARD (CONDUCTOR SIDE)
A
IC202
SW303
Z
B
RV301
EVEVATOR HEIGHT
SENSOR
(CHASSIS)
C303
C206
C205
C207
RV302
C
C204
D
C404
IC202
X401
C405
E
X301
C209
SW301
MAGAZINE
DETECT
F
(CHASSIS)
C210
C508
G
(CHASSIS)
C511
RED
C510
M
C512
BLK
C509
H
C515
13
1-680-827-
3
3
(13)
M104
(EVEVATOR)
Location
D-2
CDX-T67
SCHEMATIC DIAGRAM – MAIN Board (1/2) –
1
IC201
BA8272AFV-E2
CN201
13P
BUSON
CLK
2
SCK
Q301
DTC124EKA
SCK
SI
CLK
VREF
SO
DATA
DATA
SI
CD-ROM/RW
SO
SAVE_SW
BUSON
SELECT
SWITCH
BP5
BP6
BP10
SW301
C302
0.01
(FOR SONY BUS)
C202
4700p
I
C208
0.1
O
G
R209
47k
X1A
X0A
X0
VSS
X1
VCC
RAMIO1
RAMA0
RAMIO0
RAMA1
RAMA2
RAMA3
SINGLE
CFSEL
TEXTSEL
TEST
ESPSEL
6/10 SEL
GENERATOR
IC204
XC61CN2502PR
Q205,206
REGULATOR
MAG SW
RAMA5
SAVE SW
RESET SIGNAL
LIM SW
RAMA4
R205
47k
LOAD SW
C216
0.01
Q206
2SC2712-YG
D207
MA8056-H
X301
4MHz
C301
0.01
BUS INTERFACE
Q205
2SB1184TLR
R204
47k
BP7
RESET
RW SEL
GND
D202 UDZSTE-1718B
GND
D212 RB521S-30-TE61
GND
D204 RB521S-30-TE61
B.UP
C201
0.001
B.UP
D213
RB521S-30-TE61
RAMIO2
R301
1k
RESET
RAMA6
RAMIO3
ELVR
RAMIO4
ELVF
RAMIO5
LOADF
RAMIO6
LOADR
RAMIO7
LOADF
3
LOADR
R211
100k
C209
100
6.3V
C210
1000
16V
RAMA7
C211
0.01
C212
0.01
RAMCS
RAMA12
RAMA10
VSS
MUTE
RAMA14
EMPH
RAMWE
XWRE
RAMA13
XRDE
EMPH
C206 100
4
16V
C204
1000
16V
IC202
NJM2395AF08
CONT
I
+5V REGULATOR
GND
G
O
RAMA8
VIN
SYSTEM CONTROLLER
XQOK
XRST
IC301
MB90473PFV-G
-113-BNDE1
RAMA9
VOUT
RAMA11
C214
0.01
C215
0.01
DATA
XLAT
UNI SI
CDLAT
UNI SO
CDCLK
UNI CK
SQCK
CLOK
SO
+8V REGULATOR
(Page 5)
XRST
CDDAT
SI
IC203
NJM78M05DL
SQCK
SCK
C207 100 6.3V
D203
MA8039-H-TX
R202 220
LEDDAT
NC
LEDCLK
SQSO
SQSO
C205
100
16V
VCC
C203
0.1
HS
LEDLAT
NC
CDON
ELVON
MD2
MD1
MD0
BUCHK
BUSON
SENS
SCLK
GFS
FOK
VSS
KEY1
KEY0
MCK
EHS
AVSS
AVRH
EEDAT
AVCC
5
MAGLK SW
EJECT SW
C308
0.01
SW302
MAGAZINE
R203
150k
SENS
6
SW303
D210
UDZS-TE17
-6.2B
D209
1SS355TE
-17
C213
0.33
BUSON
C305
1
SCLK
R207
100k
GFS
ELEVATOR
MOTOR DRIVE
FOK
IN/OUT DETECT
R307 10k
BP11
NC
BP12
M104
(ELEVATOR)
R302
100k
SCOR
RX
NC
C304
0.01
FL BOOT
LB1930M-TL
EECLK
IC302
C307
0.01
NC
+3V REGULATOR
GRSCOR
SCOR
Q202
2SC2712-Y
TX
JACK
FLEXIBLE
BOARD
D201 UDZSTE-1718B
(Page 6)
DETECT
R201
47k
B.UP
R309
1k
MAGAZINE
BP9
RST
RST
SW301
BP8
C217 0.1
AGND
LIM_SW
RCH
BUSON
VCC
OUT
BUSON BUSON
IN
OUT
GND
LOF
LCH
R305
100k
Q203
2SC2712-YG
R206
120k
R308
10k
7
R303
100k
8
RV301
BATTERY
ELEVATOR HEIGHT
CHECK
SENSOR
RV301
10k
RV302
47k
C303
10
16V
9
10
11
12
4
4
CDX-T67
SCHEMATIC DIAGRAM – MAIN Board (2/2) –
1
2
R501
10k
R306
10
R502
10k
R503
10k
R504
10k
C501
150p
C502
150p
EMPH
C503
0.001
C504
0.001
R505
10k
R506
10k
R509
100k
C513
100p
C505
100p
PCMD
BCK
EMPH
XTAI
XTAO
XVSS
AVDD1
AIN1
AOUT1
LOUT1
AIN2
AVSS1
AVSS2
C401
0.1
3
SQSO
LOUT2
SQSO
AOUT2
LMUT
R519
6.8k
RMUT
R520
12k
C512
10
16V
AVDD2
C404
220
16V
XVDD
X401
16.9344MHz
C405
220
16V
R507
470
C402
0.01
LRCK
DOUT
SQCK
SQCK
XRST
VDD
R414 1k
XRST
VSS
SYSM
AVDD3
R401 3.3k
DATA
Q503
UN2226
MUTING
DATA
R511
12k
C515
47
4V
PCO
XLAT
R512
6.8k
R402
3.3k
XLAT
FILI
CLOK
FILO
SENS
CLTV
CLOK
C407
0.047
R403
10k
SENS
4
R521
10k
SCLK
SCLK
(Page 4)
R404
1M
AVSS3
VDD
RFAC
DIGITAL SIGNAL PROCESSOR,
DIGITAL SERVO PROCESSOR,
ATSK
BIAS
DIGITAL FILTER,D/A CONVERTER
SPOA
VCC
C410
220p
ASYI
IC401
CXD3017Q
SPOB
XLON
AVDD0
WFCK
IGEN
LIM_SW
SAVE_SW
ADIO
RFAC
GFS
RFDC
RFDC
SAVE_SW
VC
TE
R408
33k
C413
220p
SE
FE
VC
XTSL
TES1
TEST
FFDR
TFDR
SFDR
SSTP
MDP
VSS
TE
FRDR
SCOR
TRDR
CE
SRDR
C2PO
COUT
R508
470
R/RW_SEL
LIM_SW
C412
0.47
XPCK
LOCK
5
C411
0.01
TP403
TP404
R510
100k
C416
0.01
C403
2200p
AVSS0
FOK
SCOR
R406
100k
XUGF
DFCT
GND
GFS
R405
10k
TP402
MIRR
MUTING
100p
Q502
UN2226
TP401
C514
IC501
TLV2362IPW
CN202
22P
ASYO
R407 33k
GROUND-ISOLATION
C408
1500p
FE
DVCC(3V)
C511
10
16V
GND(5V)
R518
12k
R513
6.8k
5V
FRDR
Q501
DTA115EKA-T146
FRDR
FFDR
MUTING CONTROL
FFDR
TRDR
R517
6.8k
TRDR
R514
12k
C414
0.1
TP408
TP405
R515
10k
TP407
C506
100p
TP406
SWITCH
R410
100k
TFDR
TFDR
MDP
MDP
SRDR
SRDR
SFDR
C509
47
4V
SFDR
FRDR
FFDR
TRDR
TFDR
SRDR
C415
220p
SFDR
LIM_SW
C510
47
4V
MDP
6
C516
0.01
FOK
C508
47
4V
R412
33k
LOADR
LOADR
LOADF
LOADF
GND(8V)
7
8V
C306
0.1
8
(CHASSIS)
9
10
11
12
5
5
MAIN
FLEXIBLE
BOARD
CDX-T67
PRINTED WIRING BOARDS – JACK Board –
SCHEMATIC DIAGRAM – JACK Board –
CN902
10P
CN901
13P
FB901
(L)
JACK BOARD
LCH
LCH
FB902
AGND
AGND
FB903
(R)
(COMPONENT SIDE)
RCH
RCH
BUSON
BUSON
CLK
CLK
DATA
DATA
RST
RST
(FOR SONY BUS)
B.UP
GND
GND
B.UP
PS902
5A
24V
B.UP
B.UP
GND
GND
GND
(CHASSIS)
13
1-680-828-
(13)
(FOR SONY BUS)
6
3
(R)
(L)
7
8
JACK BOARD
4
5
2
1
(CONDUCTOR SIDE)
10
1
PS902
CN902
FB903
FB901
FB902
CN901
13
13
1-680-828-
(13)
JACK FLEXIBLE
BOARD
B
(CHASSIS)
MAIN BOARD
CN201
(Page 2)
6
6
(Page 4)
JACK
FLEXIBLE
BOARD
CDX-T67
JACK
MAIN
• ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Ref. No.
Part No.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. . : µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
Description
Remark
1-680-828-13 JACK BOARD
***********
< CONNECTOR >
CN901
1-770-350-21 CONNECTOR, FPC 13P
< FERRITE BEAD >
FB901
FB902
FB903
1-414-760-21 FERRITE
1-414-760-21 FERRITE
1-414-760-21 FERRITE
0uH
0uH
0uH
< FUSE >
PS902 1-576-592-21 FUSE (SMD) (5A/24V)
**************************************************************
A-3326-968-A MAIN BOARD, COMPLETE
*********************
< CAPACITOR >
C201
C202
C203
C204
C205
1-162-964-11
1-162-968-11
1-164-156-11
1-115-466-00
1-126-382-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.001uF
0.0047uF
0.1uF
1000uF
100uF
10%
10%
20%
20%
50V
50V
25V
16V
16V
C206
C207
C208
C209
C210
1-126-382-11
1-126-382-11
1-107-826-11
1-126-382-11
1-115-466-00
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
100uF
100uF
0.1uF
100uF
1000uF
20%
20%
10%
20%
20%
16V
6.3V
16V
6.3V
16V
C211
C212
C213
C214
C215
1-162-974-11
1-162-974-11
1-128-934-11
1-162-974-11
1-162-974-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.33uF
0.01uF
0.01uF
20%
50V
50V
10V
50V
50V
C216
C217
C301
C302
C303
1-162-974-11
1-164-156-11
1-162-974-11
1-162-974-11
1-126-791-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
0.1uF
0.01uF
0.01uF
10uF
C304
C305
C306
C307
C308
1-162-974-11
1-125-837-11
1-164-156-11
1-162-974-11
1-162-974-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
1uF
0.1uF
0.01uF
0.01uF
20%
10%
50V
25V
50V
50V
16V
50V
6.3V
25V
50V
50V
Ref. No.
When indicating parts by reference
number, please include the board.
Part No.
Description
Remark
C401
C402
C403
C404
C405
1-164-156-11
1-162-974-11
1-162-966-11
1-128-499-11
1-128-499-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.1uF
0.01uF
0.0022uF 10%
220uF
20%
220uF
20%
25V
50V
50V
16V
16V
C407
C408
C410
C411
C412
1-165-176-11
1-162-965-11
1-164-230-11
1-162-970-11
1-125-891-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.0015uF
220PF
0.01uF
0.47uF
10%
10%
5%
10%
10%
16V
50V
50V
25V
10V
C413
C414
C415
C416
C501
1-164-230-11
1-107-826-11
1-164-230-11
1-162-970-11
1-164-217-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.1uF
220PF
0.01uF
150PF
5%
10%
5%
10%
5%
50V
16V
50V
25V
50V
C502
C503
C504
C505
C506
1-164-217-11
1-162-964-11
1-162-964-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
150PF
0.001uF
0.001uF
100PF
100PF
5%
10%
10%
5%
5%
50V
50V
50V
50V
50V
C508
C509
C510
C511
C512
1-126-513-11
1-126-513-11
1-126-513-11
1-126-791-11
1-126-791-11
ELECT
ELECT
ELECT
ELECT
ELECT
47uF
47uF
47uF
10uF
10uF
20%
20%
20%
20%
20%
4V
4V
4V
16V
16V
C513
C514
C515
C516
1-162-927-11
1-162-927-11
1-126-513-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
100PF
100PF
47uF
0.01uF
5%
5%
20%
10%
50V
50V
4V
25V
< CONNECTOR >
CN201
CN202
1-770-350-21 CONNECTOR, FPC 13P
1-793-820-21 CONNECTOR, FPC 22P
< DIODE >
D201
D202
D203
D204
D207
8-719-083-66
8-719-083-66
8-719-421-24
8-719-071-34
8-719-977-03
DIODE
DIODE
DIODE
DIODE
DIODE
UDZSTB-1718B
UDZSTB-1718B
MA8039-H-TX
RB521S-30-TE61
DTZ5.6B
D209
D210
D212
8-719-988-61 DIODE 1SS355TE-17
8-719-069-56 DIODE UDZSTE-176.2B
8-719-071-34 DIODE RB521S-30-TE61
7
CDX-T67
MAIN
Ref. No.
D213
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
R508
R509
R510
R511
R512
1-216-817-11
1-216-845-11
1-216-845-11
1-219-316-11
1-218-867-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
470
100K
100K
12K
6.8K
5%
5%
5%
2%
2%
1/16W
1/16W
1/16W
1/16W
1/16W
R513
R514
R515
R517
R518
1-218-867-11
1-219-316-11
1-216-833-11
1-218-867-11
1-219-316-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
6.8K
12K
10K
6.8K
12K
2%
2%
5%
2%
2%
1/16W
1/16W
1/16W
1/16W
1/16W
R519
R520
R521
1-218-867-11 RES-CHIP
1-219-316-11 RES-CHIP
1-216-833-11 METAL CHIP
6.8K
12K
10K
2%
2%
5%
1/16W
1/16W
1/16W
8-719-071-34 DIODE RB521S-30-TE61
< IC >
IC201
IC202
IC203
IC204
IC301
8-759-829-46
8-759-833-13
8-759-358-38
8-759-827-97
6-800-420-01
IC
IC
IC
IC
IC
BA8272AFV-E2
NJM2395AF08
NJM78M05DLA (TE1)
XC61CN2502PR
MB90473PFV-G-113-BNDE1
IC302
IC401
IC501
8-759-527-33 IC LB1930M-TLM
8-752-402-31 IC CXD3017Q
8-759-662-11 IC TLV2362IPWR
< TRANSISTOR >
Q202
Q203
Q205
Q206
Q301
8-729-200-13
8-729-230-49
8-729-922-47
8-729-230-49
8-729-901-00
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q501
Q502
Q503
8-729-028-62 TRANSISTOR
8-729-015-39 TRANSISTOR
8-729-015-39 TRANSISTOR
2SC2712-Y
2SC2712-YG-TE85L
2SB1184-TLR
2SC2712-YG-TE85L
DTC124EKA-T146
< VARIABLE RESISTOR >
RV302
1-223-834-11 RES, ADJ, CARBON 47K
< SWITCH >
DTA115EKA-T146
UN2226-(TX)
UN2226-(TX)
SW301 1-771-540-11 SWITCH, PUSH (1KEY) (MAGAZINE DETECT)
SW302 1-529-566-31 SWITCH, PUSH (1KEY)
(MAGAZINE IN/OUT DETECT)
SW303 1-692-431-21 SWITCH, TACTILE (Z)
< RESISTOR >
8
R201
R202
R203
R204
R205
1-216-841-11
1-216-813-11
1-216-847-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
220
150K
47K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R206
R207
R209
R211
R301
1-216-846-11
1-216-845-11
1-216-841-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120K
100K
47K
100K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R302
R303
R305
R306
R307
1-216-845-11
1-216-845-11
1-216-845-11
1-216-797-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
10
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R308
R309
R401
R402
R403
1-216-833-11
1-216-821-11
1-216-827-11
1-216-827-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
3.3K
3.3K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R404
R405
R406
R407
R408
1-216-857-11
1-216-833-11
1-216-845-11
1-216-839-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
10K
100K
33K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R410
R412
R414
R501
R502
1-216-845-11
1-216-839-11
1-216-821-11
1-218-871-11
1-218-871-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
100K
33K
1K
10K
10K
5%
5%
5%
2%
2%
1/16W
1/16W
1/16W
1/16W
1/16W
R503
R504
R505
R506
R507
1-218-871-11
1-218-871-11
1-218-871-11
1-218-871-11
1-216-817-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
10K
10K
10K
10K
470
2%
2%
2%
2%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< VIBRATOR >
X301
X401
1-781-282-11 VIBRATOR, CERAMIC (4MHz)
1-760-307-11 VIBRATOR, CERAMIC (16.9344MHz)
CDX-T67
MEMO
9
CDX-T67
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
1.0
1.1
Date
2001.03
2001.05
1.2
1.3
1.4
2001.06
2001.09
2002.07
Description of Revision
New
Change of Ref. No. for Main flexible board from 11 to 117
Addition of SPACER (BUTTON EJECT), CUSHION (DAMPER),
CUSHION (JACK), SPACER (CASE LOWER), and CUSHION
(CHASSIS 6T)
Addition of C220 on RF board
Change of C303 on MAIN board
Change of Part No. for SW102 on RF board
Addition of SPACER (TRAY RETAINER), SPACER
(DISC RETAINER L)
(ECN-CSB02787/CSB02801/CSB02814/CSB02816/CSB02817/CSB02835)
Change of MAIN/JACK/RF boards (Suffix-12)
(ECN-CSA04865/CSB02866)
Change of MAIN/JACK boards (Suffix-13)
(ECN-CSB03047)
Correction of Ref. No. 1 and Ref. No. 2
(SPM-02004)