Download SERVICE MANUAL

HCD-XG80/XG700
SERVICE MANUAL
AEP Model
UK Model
Ver 1.0 2001.03
HCD-XG700
E Model
HCD-XG80
HCD-XG80/XG700 is the amplifier, CD
player, tape deck and tuner section in
LBT-XG80/XG700.
Photo: HCD-XG80
Dolby noise reduction manufactured under license
from Dolby Laboratories Licensing Corporation.
“DOLBY” and the double-D symbol ; are trademarks of Dolby Laboratories Licensing Corporation.
CD
Section
TAPE
Section
Model Name Using Similar Mechanism
HCD-LX6/LX50/LX70
CD Mechanism Type
CDM37M-5BD32L
Base Unit Name
BU-5BD32L
Optical Pick-up Name
KSS-213DH
Model Name Using Similar Mechanism
NEW
Tape Transport Mechanism Type
TCM-230PWR42
SPECIFICATIONS
Amplifier section
AEP, UK models:
DIN power output (rated) 200 + 200 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
250 + 250 watts
(6 ohms at 1 kHz, 10% THD)
Music power output (reference)
430 + 430 watts
(6 ohms at 1 kHz, 10% THD)
Other models:
The following measured at AC 120/220/240V, 50 Hz
DIN power output (rated) 240 + 240 watts
(4 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
320 + 320 watts
(4 ohms at 1 kHz, 10% THD)
Inputs
DJ MIX*:
(phono jacks)
sensitivity 250 mV,
impedance 47 kilohms
GUITAR IN:
(phone jack)
sensitivity 75 mV,
impedance 470 kilohms
PHONO IN:
(phono jacks)
sensitivity 3 mV,
impedance 47 kilohms
MIX MIC:
(phone jack)
sensitivity 1 mV,
impedance 10 kilohms
VIDEO IN:
(phono jacks)
GAME IN:
(phono jacks)
MD IN:
(phono jack)
Outputs
DJ MIX*:
(phono jacks)
PHONES:
(stereo phone jack)
VIDEO OUT:
(phono jack)
MD OUT:
(phono jacks)
FRONT SPEAKER:
HCD-XG80:
CD player section
sensitivity 250 mV,
impedance 47 kilohms
sensitivity 250 mV,
impedance 47 kilohms
sensitivity 450 mV,
impedance 47 kilohms
sensitivity 250 mV,
impedance 1 kilohms
accepts headphones of 8
ohms or more
voltage 250 mV
impedance 1 kilohm
voltage 250 mV
impedance 1 kilohm
accepts impedance of 4 to
16 ohms
System
Compact disc and digital
audio system
Laser
Semiconductor laser
(λ=780nm), Emission
duration: continuous
Wavelength
780 – 790 nm
Frequency response
2 Hz – 20 kHz (±0.5 dB)
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 90 dB
CD OPTICAL DIGITAL OUT
(Square optical connector jack, rear panel)
Wavelength:
660 nm
Output level
–18 dBm
Tape player section
Recording system
Frequency response
(DOLBY NR OFF)
4-track 2-channel stereo
40 – 13,000 Hz (±3 dB),
using Sony TYPE I cassette
40 – 14,000 Hz (±3 dB),
using Sony TYPE II cassette
– Continued on next page –
HCD-XG700:
accepts impedance of 6 to
16 ohms
* AEP, UK and Mexican models only
COMPACT DISC DECK RECEIVER
9-929-596-11
Sony Corporation
2001C0500-1
C 2001.3
Audio Entertainment Group
General Engineering Dept.
HCD-XG80/XG700
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate frequency
87.5 – 108.0 MHz
(50 kHz step)
FM lead antenna
75 ohm unbalanced
10.7 MHz
AM tuner section
Tuning range
Pan- American models:
530 – 1,710 kHz
(with the interval set at 10
kHz)
531 – 1,710 kHz
(with the interval set at 9
kHz)
European and Middle Eastern models:
531 – 1,602 kHz
(with the interval set at 9
kHz)
Other models:
531 – 1,602 kHz
(with the interval set at 9
kHz)
530 – 1,710 kHz
(with the interval set at 10
kHz)
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency
450 kHz
General
Power requirements
AEP, UK models:
Mexican model:
Other models:
Power consumption
AEP, UK models:
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
The following caution label is located inside the unit.
230 V AC, 50/60 Hz
120 V AC, 50/60 Hz
120 V, 220 V or 230 – 240
V AC, 50/60 Hz
Adjustable with voltage
selector
220 watts
0.6 watts (at the power
saving mode)
Other models:
300 watts
Dimensions (w/h/d)
Approx. 355 x 425 x 450
mm
Mass :
HCD-XG700
HCD-XG80
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Approx. 15.5 kg
Approx. 16.0 kg
Design and specifications are subject to change
without notice.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
HCD-XG80/XG700
TABLE OF CONTENTS
1.
2.
SERVICING NOTES ................................................ 4
GENERAL
Location of Controls ....................................................... 5
Setting the Time .............................................................. 6
3.
DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
Disassembly Flow ...........................................................
Case .................................................................................
Front Panel Section .........................................................
Cover (TC), Tape Mechanism Deck
(TCM-230PWR42) .........................................................
MAIN Board, Fan, D.C. (M901) ....................................
CD Mechanism Deck (CDM37M-5BD32L) ..................
Base Unit (BU-5BD32L) ................................................
Disc Table ........................................................................
4.
TEST MODE .............................................................. 12
5.
MECHANICAL ADJUSTMENTS ....................... 14
6.
ELECTRICAL ADJUSTMENTS
7
7
8
8
9
10
11
11
8.
8-1.
8-2.
8-3.
8-4.
8-5.
EXPLODED VIEWS
Case, Back Panel Section ................................................
Front Panel Section-1 ......................................................
Front Panel Section-2 ......................................................
Chassis Section ...............................................................
Tape Mechanism Deck Section-1
(TCM-230PWR42) .........................................................
8-6. Tape Mechanism Deck Section-2
(TCM-230PWR42) .........................................................
8-7. CD Mechanism Deck Section (CDM37M-5BD32L) ....
8-8. Base Unit Section (BU-5BD32L) ...................................
9.
55
56
57
58
59
60
61
62
ELECTRICAL PARTS LIST ............................... 63
Deck section .................................................................... 14
CD Section ...................................................................... 17
7.
DIAGRAMS
7-1.
7-2.
7-3.
7-4.
Block Diagram – CD SERVO Section – .......................
Block Diagram – TUNER/TAPE DECK Section – ......
Block Diagram – MAIN Section – ................................
Block Diagram – DISPLAY/KEY CONTROL/
POWER SUPPLY Section – ...........................................
Note for Printed Wiring Boards and
Schematic Diagrams .......................................................
Printed Wiring Board – BD Board – .............................
Schematic Diagram – BD Board – ................................
Printed Wiring Boards – CD MOTOR Section – ..........
Schematic Diagram – CD MOTOR Section – ..............
Printed Wiring Board – AUDIO Board – ......................
Schematic Diagram – AUDIO Board – .........................
Printed Wiring Board – LEAF SW Board – ..................
Schematic Diagram – LEAF SW Board – .....................
Schematic Diagram – MAIN Board (1/3) – ..................
Schematic Diagram – MAIN Board (2/3) – ..................
Schematic Diagram – MAIN Board (3/3) – ..................
Printed Wiring Board – MAIN Board – ........................
Printed Wiring Board – PA Board – ..............................
Schematic Diagram – PA Board – .................................
Printed Wiring Boards – MIC/FRONT INPUT/
HEADPHONES Boards – ...............................................
Schematic Diagram – MIC/FRONT INPUT/
HEADPHONES Boards – .............................................
Printed Wiring Board – PANEL FL Board – ................
Schematic Diagram – PANEL FL Board – ...................
Printed Wiring Boards
– PANEL VR/ILLUMINATION Boards – .....................
Schematic Diagram
– PANEL VR/ILLUMINATION Boards – .....................
Printed Wiring Boards – TC-A/TC-B/CD-L/
CD-R (1)/CD-R (2) Boards – .........................................
Schematic Diagram – TC-A/TC-B/CD-L/
CD-R (1)/CD-R (2) Boards – .........................................
Printed Wiring Boards – TRANSFORMER Section– ..
Schematic Diagram – TRANSFORMER Section– .......
IC Pin Function Description ...........................................
7-5.
7-6.
7-7.
7-8.
7-9.
7-10.
7-11.
7-12.
7-13.
7-14.
7-15.
7-16.
7-17.
7-18.
7-19.
7-20.
7-21.
7-22.
7-23.
7-24.
7-25.
7-26.
7-27.
7-28.
7-29.
7-30.
19
20
21
22
23
24
25
26
27
28
29
30
30
31
32
33
34
36
37
38
39
40
41
42
43
44
45
46
46
50
3
HCD-XG80/XG700
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
• MODEL IDENTIFICATION
– Rear Panel –
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
PART No.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveforms is output three times.
4
MODEL
PART No.
AEP and UK models
4-232-088-0[]
120 V AC area in E model
4-232-088-1[]
Singapore model
4-232-088-2[]
Mexican model
4-232-088-3[]
Saudi Arabia model
4-232-088-4[]
Argentina model
4-232-088-5[]
HCD-XG80/XG700
SECTION 2
GENERAL
This section is extracted from
instruction manual.
LOCATION OF CONTROLS
– Front Panel –
1
2 3 4 5 6 789
q;
qa
ra
r;
el
qs
qd
ek
ej
eh
eg
ef
ed
qf
qg
qh
qj
qk
es
ea
e;
wl wk wj wh wg wf wd wswa w;ql
A EJECT Z/Z B EJECT wg (15)
AUDIO L w; (23)
AUDIO R ql (23)
CD SYNC qg (16,17)
DIRECT EQUALIZER 5 (18)
SALSA
REGGAE
SAMBA
TANGO
MOVIE
GUITAR
ROCK
JAZZ
DANCE
GAME
DIRECTION eh (15,16,17)
DISC SKIP qk (9,10,17)
DISC 1~5 wj (9)
DISPLAY 3 (8,11,13)
DOLBY NR eh (15,16)
EDIT wl (17)
ENTER wh (12,14)
ENTER/NEXT qd (8,17,19,22,27)
FLASH e; (11)
FLAT qd (18)
FUNCTIONq; (7,9,10,16,17,23,24)
GAME qa (21)
GROOVE r; (18)
GUITAR DISTORTION wh (21)
GUITAR jack es (21)
GUITAR LEVEL eg (21)
H SPEED DUB qg (16)
Jog dial (AMS./>) qj
(9,10,11,17)
LOOP ea (7,11)
MIC LEVEL ef (20)
MIX GUITAR/KARAOKE ej (20,21)
MIX MIC jack ed (20)
NON STOP wk (10)
P.FILE qd (18,19)
PHONES jack qh
PLAY MODE qk (9,10,17)
POWER SAVE/DEMO
(STANDBY) 2 (8)
PTY ws (14) (AEP, UK models)
PUSH OPEN wf (9)
REPEAT qk (9)
SLEEP 7 (21)
SPECTRUM ANALYZER 4 (20)
STEREO/MONO ws (13)
SUPER WOOFER el (18)
SUPER WOOFER MODE ek (18)
SURROUND ra(16,18)
TIMER SELECT 8 (17, 22)
TUNER/BAND wd(12,13,16)
TUNER MEMORY wh (12)
TUNING MODE ws (12,13)
VIDEO wa (23)
VOLUME control qs (9,13)
BUTTON DESCRIPTIONS
@/1 1
c/CLOCK SET 6
v/V/b/B 9
z REC qf
X qf
m /M, AMS./> qfeh
h,H qfeh
x qfqkeh
m /M qk
HX qk
+/– wd
5
HCD-XG80/XG700
– Rear Panel –
1
1 ANTENNA terminal
2 DJ MIX RETURN/SEND jack
(AEP, UK, Mexican models)
2
3 PHONO IN jack
3
4 MD IN/OUT jack
4
5
9
6
5 VIDEO/AUDIO IN jack
6 VIDEO OUT jack
7
7 FRONT SPEAKER terminal
8
8 CD DIGITAL OUT OPTICAL terminal
9 VOLTAGE SELECTOR switch
(120 V AC area in E, Saudi Arabia, Singapore, Argentina models)
Remote control
Setting the time
1
2
1 2 3
w;
ql
qk
qj
Press c/CLOCK SET.
When you set the time for the first time,
skip to the step 5.
ws
wa
Turn on the system.
4
5
6
7
8
9
qh
q;
qa
qg
qf
qs
3
Press v/V repeatedly to select SET
CLOCK.
4
5
6
Press ENTER/NEXT.
Press v/V repeatedly to set the hour.
Press ENTER/NEXT.
The minute indication flashes.
7
8
Press v/V repeatedly to set the minute.
Press ENTER/NEXT.
The clock starts working.
Tip
qd
If you’ve made a mistake or want to change the time,
start over from step 1.
Note
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
AMS ./>, PRESET+/– 5
(9,13,14,15)
CD N wa (9)
CHECK 8 (10)
CLEAR 7 (10)
DECK A N ql (15)
DECK B N qk (15)
DISC SKIP 1 (9,10,17)
FILE SELECT ON/OFF qf (18)
FILE SELECT F/f qg (11)
FLASH qs (11)
FUNCTION qa (7,9,10,16,17,23,24)
LOOP qh (11)
MD N qj
MD X 0
MD x 9
SLEEP 2 (21)
TUNER/BAND w;(12,16)
VOL +/– qd (9,13,15)
6
BUTTON DESCRIPTIONS
@/1 3
x4
m/M 6
X ws
HCD-XG80/XG700
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SET
3-2. CASE
(Page 7)
3-3. FRONT PANEL SECTION
(Page 8)
3-4. COVER (TC),
TAPE MECHANISM DECK
(TCM-230PWR42)
(Page 8)
3-5. MAIN BOARD,
FAN, D.C. (M901)
(Page 9)
3-6. CD MECHANISM DECK
(CDM37M-5BD32L)
(Page 10)
3-7. BASE UNIT
(BU-5BD32L)
(Page 11)
3-8. DISC TABLE
(Page 11)
Note: Follow the disassembly procedure in the numerical order given.
3-2.
CASE
2 five screws
(BVTT3 × 6)
6 case
1 three screws
(CASE3 TP2)
3 two screws
(BVTP3 × 8)
4
5
5
4
1 three screws
(CASE3 TP2)
7
HCD-XG80/XG700
3-3.
FRONT PANEL SECTION
1 wire (flat type)
(15 core) (CN303)
1 wire (flat type)
(17 core) (CN304)
3 two screws
(BVTP3 × 8)
2 two connectors
(CN452, 702)
1 wire (flat type)
(13 core) (CN431)
3 screw
(BVTP3 × 8)
4 two lugs
4 lug
2 connector
(CN806)
5 screw
(BVTP3 × 8)
6 claw
7 front panel section
5 four screws
(BVTP3 × 8)
3-4.
COVER (TC), TAPE MECHANISM DECK (TCM-230PWR42)
4 two screws
(BVTP3 × 8)
3 wire (flat type) (17 core)
(CN1001)
3 wire (flat type) (15 core)
(CN601)
4 two screws
(BVTP3 × 8)
1 five claws
5 tape mechanism deck
(TCM-230PWR42)
2 cover (TC)
8
HCD-XG80/XG700
3-5.
MAIN BOARD, FAN, D.C. (M901)
1 wire (flat type)
(13 core) (CN441)
AEP, UK, Mexican models
3 eight screws
(BVTP3 × 8)
2 jumper plug
8 back panel
3 screw
(BVTP3 × 8)
9 wire (flat type) (19 core)
(CN411)
3 three screws
(BVTP3 × 8)
7 fan, D.C.
(M901)
6 two screws
(BVTP3 × 8)
3 three screws
(BVTP3 × 8)
3 three screws
(BVTP3 × 8)
4
5 connector (CN903)
qd MAIN board
qa two screws
(BVTP3 × 8)
0 connector
(CN412)
qs two connectors
(CN901, 902)
9
HCD-XG80/XG700
3-6.
CD MECHANISM DECK (CDM37M-5BD32L)
1 wire (flat type)
(19 core) (CN411)
4 three screws
(BVTP3 × 8)
3 four screws
(BVTP3 × 8)
5
7 Open the cable clamp.
6
5
2 connector
(CN412)
4 two screws
(BVTP3 × 8)
8 five screws
(BVTP3 × 8)
9 CD mechanism deck
(CDM37M-5BD32)
10
HCD-XG80/XG700
3-7.
BASE UNIT (BU-5BD32L)
3 base unit
(BU-5BD32L)
2 boss
1 BU fitting screw
3-8.
DISC TABLE
Note: When the disc table is installed, adjust the positions of roller cam
and mark B as shown in the figure, then set to the groove of disc
table.
A
3 step screw
1 two screws
(BVTP3 × 8)
2 two brackets (BU)
4 disc table
A
11
HCD-XG80/XG700
SECTION 4
TEST MODE
[MC Cold Reset]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
Procedure:
1. Turn the power ON or set to the DEMO mode.
2. Press three buttons of [ c /CLOCK SET], [ENTER/NEXT], and
?/1 simultaneously.
3. The set is reset, and displays “COLD RESET”, then becomes
DEMO mode.
[MC Hot Reset]
• This mode resets the set with the preset data kept stored in the
memory. The hot reset mode functions same as if the power
cord is plugged in and out.
Procedure:
1. Turn the power ON or set to the DEMO mode.
2. Press three buttons of [ c /CLOCK SET], [ENTER/NEXT],
and [DISC 1] simultaneously.
3. The set is reset, and becomes standby state.
[Change-over the AM Tuning Interval]
(EXCEPT AEP, UK, and Saudi Arabia models)
• The AM tuning interval can be changed over 9 kHz or 10 kHz.
Procedure:
1. Press the ?/1 button to turn the power ON.
2. Select the function “TUNER”, and press the [TUNER/BAND]
button to select the BAND “AM”.
3. Press the ?/1 button to turn the power OFF.
4. Press the [ENTER/NEXT] and ?/1 buttons simultaneously,
and the display on the fluorescent indicator tube changes to
“AM 9 K STEP” or “AM 10 K STEP”, and thus the tuning
interval is changed over.
12
[CD Delivery Mode]
• This mode moves the optical pick-up to the position durable to
vibration. Use this mode when returning the set to the customer
after repair.
Procedure:
1. Press the ?/1 button to turn the power ON.
2. Press the [LOOP] and ?/1 buttons simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator
tube, and the CD delivery mode is set.
[LED and Fluorescent Indicator Tube All Lit, Key Check
Mode]
Procedure:
1. Press three buttons of [ c /CLOCK SET], [ENTER/NEXT],
and [DISC 2] simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
Press the [DISC 2] button, and the key check mode is activated.
3. In the key check mode, the fluorescent indicator tube displays
“K 0 J0 V0”. Each time a button is pressed, “K” value increases. However, once a button is pressed, it is no longer taken
into account.
“J” value increases like 1, 2, 3 ... if turn the JOG dial clockwise, or it decreases like 0, 9, 8 ... if turn the JOG dial counterclockwise.
“V” value increases like 1, 2, 3 ... if turn the [VOLUME] dial
clockwise, or it decreases like 0, 9, 8 ... if turn the JOG dial
counterclockwise.
4. To release from this mode, press three buttons in the same
manner as step 1, or disconnect the power cord.
HCD-XG80/XG700
[Aging Mode]
This mode can be used for operation check of tape deck section.
Tape deck section work in parallel.
• If an error occurred:
The aging operation stops and display then status.
• If no error occurs:
The aging operation continues repeatedly.
Procedure:
1. Load the tapes into the decks A and B respectively.
2. Press the [FUNCTION] button to select the function “CD”.
3. Press the [PLAY MODE] button to set the “ALL DISCS” mode,
and press the [REPEAT] button to “REPEAT” off.
4. Press three buttons of [ c /CLOCK SET], [ENTER/NEXT],
and [DISC 4] simultaneously.
5. The aging mode is activated, if the indicator of disc tray number on the fluorescent indicator tube is blinking.
6. To release from the aging mode, press the ?/1 button to turn
the power OFF and operate the cold reset. (Refer to the “MC
Cold Reset”)
1. Display at the Aging Mode
• Display operating state of tape deck section alternately.
• If an error occurred, stop display.
2. Tape Deck Section
• The sequence during the aging mode is following as below.
• If an error occurred, stop display that step.
Aging mode sequence (Tape deck section) :
Rewind the tape A and B
“TAPE A AG-1”
Shut off
FWD play the tape A
“TAPE A AG-2”
2 minutes
Fast forward the tape A
“TAPE A AG-3”
Shut off or 20 seconds
REV play the tape A
“TAPE A AG-4”
2 minutes
Rewind the tape A
“TAPE A AG-5”
Shut off
FWD play the tape B
“TAPE B AG-2”
2 minutes
Fast forward the tape B
“TAPE B AG-3”
Shut off or 20 seconds
REV play the tape B
“TAPE B AG-4”
2 minutes
Rewind the tape B
“TAPE B AG-5”
Shut off
Note: “TAPE * AG-*” is display of each step.
13
HCD-XG80/XG700
SECTION 5
MECHANICAL ADJUSTMENTS
Precaution
1. Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads pinch rollers
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power supply voltage unless otherwise noted.
Torque Measurement
Mode
Torque Meter
Meter Reading
FWD
CQ-102C
3.1~6.96 mN•m
(31 to 71 g•cm)
(0.43 – 0.98 oz•inch)
FWD
back tension
CQ-102C
0.20~0.58 mN•m
(2 to 6 g•cm)
(0.03 – 0.08 oz•inch)
REV
CQ-102RC
3.1~6.96 mN•m
(31 to 71 g•cm)
(0.43 – 0.98 oz • inch)
REV
back tension
CQ-102RC
0.20~0.58 mN•m
(2 to 6 g•cm)
(0.03 – 0.08 oz • inch)
FF/REW
CQ-201B
6.97~14.02 mN•m
(71 to 143 g•cm)
(0.99 – 1.99 oz • inch)
FWD tension
CQ-403A
9.80 mN•m
(100 g or more)
(3.53 oz or more)
CQ-403A
9.80 mN•m
(100 g or more)
(3.53 oz or more)
REV tension
14
SECTION 6
ELECTRICAL ADJUSTMENTS
DECK SECTION
0 dB = 0.775 V
Precaution
1. Demagnetize the record/playback head with a head demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
parts adjust.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in
this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording
circuit adjustment.)
6. The adjustments should be performed for both L-CH and RCH.
7. Switches and controls should be set as follows unless otherwise specified.
8. Set to the DOLBY NR OFF.
9. Set to the test mode.
(1) Press the ?/1 button to turn the power ON.
(2) Select the function “TAPE A or B”.
(3) Press the button of [ c /CLOCK SET], [ENTER/NEXT],
and [DISC 3] simultaneously, to set the tape deck test mode
and displays “TEST MODE” on the fluorescent indicator
tube.
(4) To release from the test mode, press the ?/1 button.
• Test Tape
Tape
Signal
Used for
P-4-A100
10 kHz, – 10 dB
Azimuth Adjustment
WS-48B
3 kHz, 0 dB
Tape Speed Adjustment
P-4-L300
315 Hz, 0 dB
Playback Level Adjustment
HCD-XG80/XG700
Record/Playback Head Azimuth Adjustment
DECK A
Adjustment Location: Playback Head (Deck A).
Record/Playback/Erase Head (Deck B).
DECK B
Note: Perform this adjustments for both decks
Procedure:
1. Mode: Playback (FWD)
test tape
P-4-A100
(10 kHz, – 10 dB)
MAIN board
MD OUT jack (J701)
L-CH, R-CH
level meter
set
forward
+
–
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
within
1dB
Output
level
Screw
position
Tape Speed Adjustment
Mode: Playback
DECK B
test tape
WS-48B
(3 kHz, 0 dB)
within
1dB
L-CH
peak
reverse
frequency counter
+
–
set
MAIN board
MD OUT jack (J701)
L-CH, R-CH
R-CH
peak
L-CH
peak
Screw
position
R-CH
peak
3. Mode: Playback
test tape
P-4-A100
(10 kHz, – 10 dB)
L-CH
MAIN board
MD OUT jack (J701)
L-CH
oscilloscope
V
set
H
1. Insert the WS-48B into the deck B.
2. Press the H button on the deck B.
3. Press the [H SPEED DUB] button in playback mode.
Then at HIGH speed mode.
4. Adjust RV1001 on the LEAF SW board do that frequency
counter reads 6,000 ± 180 Hz.
5. Press the [H SPEED DUB] button.
Then back to NORMAL speed mode.
6. Adjust RV1002 on the LEAF SW board so that frequency
counter reads 3,000 ± 90 Hz.
Adjustment Location: LEAF SW board
Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)
(WS-48B)
R-CH
R-CH
waveform of oscilloscope
in phase 45°
good
90° 135° 180°
wrong
4. Repeat step 1 to 3 in playback (REV) mode.
5. After the adjustments, apply suitable locking compound to the
pats adjusted.
Playback Level Adjustment
Procedure:
Mode: Playback
DECK A
test tape
P-4-L300
(315 Hz, 0 dB)
DECK B
level meter
set
+
–
MAIN board
MD OUT jack (J701)
L-CH
Deck A is RV311 (L-CH), Deck B is RV301 (L-CH) so that adjustment within specification values as follows.
Specification Values:
J101 PB level: 301.5 to 338.3 mV (– 8.2 to – 7.2 dB) level
difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board
15
HCD-XG80/XG700
Specification values:
J101 PB level: 47.2 to 53.0 mV (– 24.3 to – 23.3 dB)
REC Bias Adjustment DECK B
Procedure:
1. Mode: Record
FUNCTION: VIDEO
AF OSC
Adjustment Location: MAIN board
MAIN board
VIDEO AUDIO IN jack (J701)
L-CH, R-CH
1) 315 Hz 
50 mV (– 23.8 dB)
2) 10 kHz 
attenuator
600 Ω
– MAIN BOARD (Conductor Side) –
blank tape
CN-123
MD OUT
L/R











set
VIDEO
AUDIO IN
L/R
J701
RV301 
L-CH 


IC301
 REC LEVEL


RV351


R-CH
2. Mode: Playback
recorded
portion
level meter
+
–
set
MAIN board
MD OUT jack (J701)
L-CH, R-CH
– AUDIO BOARD (Component Side) –
3. Confirm playback the signal recorded in step 1 become specification values as follows.
If these values are out of specification values, adjust the RV341
(L-CH) and RV441 (R-CH) on the AUDIO board to repeat
steps 1and 2.
REC Level Adjustment DECK B
Procedure:
1. Mode: Record
FUNCTION: VIDEO
PB LEVEL (L)
– DECK A –
(NORMAL) (HIGH)
RV1002
blank tape
CS-123
attenuator
set
2. Mode: Playback
level meter
+
–
MAIN board
MD OUT jack (J701)
L-CH, R-CH
3. Confirm playback the signal recorded in step 1 become specification values as follows.
If these values are out of specification values, adjust the RV301
(L-CH) and RV351 (R-CH) on the MAIN board to repeat steps
1 and 2.
16
PB LEVEL R L
(L)
REC BIAS
– DECK B –
TAPE SPEED
600 Ω
set
RV311
– LEAF SW BOARD (Component Side) –
MAIN board
VIDEO AUDIO IN jack (J701)
L-CH, R-CH
315 Hz, 50 mV (– 23.8 dB)
recorded
portion
CN601
RV341










AF OSC
IC602
RV301



Specification values: Playback output of 315 Hz to playback
output of 10 kHz: ± 0.5 dB
Adjustment Location: AUDIO board
RV441
RV1001
CN1001
HCD-XG80/XG700
E-F Balance (1 Track Jump) Check
CD SECTION
oscilloscope
(DC range)
Note:
1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10 MΩ impedance.
4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specified value with the following checks.
TP (TE)
TP (VC)
+
–
Procedure :
1. Connect oscilloscpe to TP (TE) and TP (VC).
2. Turn the power ON.
3. Load a disc (YEDS-18) and playback the number five track.
4. Press the H X button. (Becomes the 1 track jump mode)
5. Confirm that the level B and A (DC voltage) on the oscilloscope waveform.
S-Curve Check
oscilloscope
BD board
TP (FE)
TP (VC)
BD board
+
–
Procedure:
1. Connect oscilloscope to TP (FE) and TP (VC).
2. Connect between TP (FE1) and TP (VC) by lead wire.
3. Connect between TP (AGCCON) and TP (GND) by lead wire.
4. Turn the power ON.
5. Load a disc (YEDS-18) and actuate the focus search. (In consequence of open and close the disc tray, actuate the focus
search)
6. Cofirm that the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within
4 ± 1 Vp-p.
1 track jump waveform
center of
waveform
B
A (DC voltage)
0V
level = 1.3 ± 0.6 Vp-p
Specified level:
S-curve waveform
symmetry
A
× 100 = less than ± 22%
B
symmetry
6. After check, remove the lead wire connected in step 1.
A
within 4 ± 1 Vp-p
Checking Location:
– BD BOARD (Side B) –
B
7. After check, remove the lead wire connected in step 2 and 3.
Note: • Try to measure several times to make sure than the ratio of A : B
or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the brightness
to obtain best waveform.
TP (GND)
TP (VC)
RF Level Check
oscilloscope
(AC range)
BD board
TP (RF)
TP (VC)
IC102
TP (RF)
+
–
Procedure:
1. Connect oscilloscope to TP (RF) and TP (VC).
2. Connect between TP (AGCCON) and TP (GND) by lead wire.
3. Turn the power ON.
4. Load a disc (YEDS-18) and press the H X button to play.
5. Confirm that the oscilloscope waveform is clear and check RF
signal level is correct or not.
6. After check, remove the lead wire connected in step 2.
IC103
TP (AGCCON)
TP (FE)
TP (TE)
TP (FE1)
Note: Clear RF signal waveform means that the shape “ ” can be clearly
distinguished at the center of the waveform.
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
(with the 10: 1 probe
in use)
level:
1.45 ± 0.3 Vp-p
17
HCD-XG80/XG700
MEMO
18
HCD-XG80/XG700
SECTION 7
DIAGRAMS
7-1.
BLOCK DIAGRAM – CD SERVO Section –
(XG80 : Mexican/XG700)
FILTER
55
4
5
2
6
1
7
5
8
B
C
I-V AMP
D
F
10
10
6
11
E
A
RF
SUMMING
AMP
B
RF EQ RFO
16
AMP
51
49
C
48
D
F
E
FOCUS
ERROR AMP
FE
TRACKING
ERROR AMP
TE
RFAC
ASYMMETRY
CORRECTION
EFM
DEMODULATOR
DIGITAL
PLL
ASYI
D/A
INTERFACE
INTERNAL BUS
16K
RAM
7
A
J705
L
SEND
R-CH
FILI
PCO
56 53
CLTV
CD D+5V
54
FILO
DETECTOR
RF AMP,
FOCUS/TRACKING ERROR AMP
IC103
DIGITAL SIGNAL PROCESSOR,
DIGITAL FILTER, D/A CONVERTER
IC101 (1/2)
PCMD
62
BCK
63
LRCK
61
C2PO
19
14
ERROR
CORRECTOR
SUBCODE
PROCESSOR
DIGITAL
CLV
13
26
LDON
LASER DIODE
LD
3
LD
APC LD
AMP
PD
APC PD
AMP
3
SERVO AUTO
SEQUENCER
14
5 6 7
8
PWM
&
INTEGRATOR
DIGITAL
FILTER,
NOISE SHAPER
AOUT1
AOUT2
70
AIN1
71
77
SERVO
INTERFACE
AIN2
76
LOUT1
BUFFER
LOUT2
75
20
1 2
CLOCK
GENERATOR
XTAI
TIMING
LOGIC
DOUT
EMPH
WFCK
GFS
SCLK
COUT
SSTP
9 21 27
64 15 18
XTAO
R-CH
66
67
X101
16.9344MHz
IC781
CD DIGITALOUT
OPTICAL
S101
(LIMIT)
OPTICAL
TRANSCEIVER
IC781
ON : When the optical pick-up
is inner position.
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
IC102
33 SQ-CLK
32 SQ-DATA
19 SCOR
M101
(SPINDLE)
M
15
16
CH4OUTF
CH4OUTR
MOTOR
DRIVE
CH4SIN
56 SENS
25
37 CD-CLK
58 XLT
35 CD-DATA
57 HOLD
18
CH3FIN
CH3OUTF
CH3OUTR
MOTOR
DRIVE
CH3RIN
24
A/D
CONVERTER
23
28
(FOCUS) (TRACKING)
2-AXIS
DEVICE
29
12
11
CH2OUTF
CH2OUTR
CH2FIN
COIL
DRIVE
CH2RIN
5
6
30
31
32
33
14
13
CH1FIN
CH1OUTF
CH1OUTR
COIL
DRIVE
CH1RIN
T-SENS 61
DIGITAL SERVO
PROCESSOR
IC101 (2/2)
DISC TABLE
SENSOR
IC202
ENC3/UP-SW 68
S201
(UP)
SFDR
SRDR
TFDR
TRDR
FFDR
FRDR
FOCUS/TRACKING/SLED
SERVO DSP
M
17
FOCUS/TRACKING/SLED
PWM GENERATOR
M102
(SLED)
TE
FE
RFDC
SE
40 41 39 43
MIRR/DFCT/
FOK
DETECTOR
FOK
24
MIRR
22
DFCT
23
ENC2/DISC-LED 69
SYSTEM CONTROLLER
(CD MECHANISM CONTROL)
IC501 (1/4)
TABLE MOTOR DRIVER
IC201
2
TO SERVO INTERFACE
TBL-L 63
3
TBL-R 65
MUTE 20
D201
(DISC No.)
LED DRIVE
Q201
9
1
OUT1
IN1
IN2
MOTOR
DRIVE
OUT2
7
3
M
M201
(TABLE)
59 XRST
• R-ch is omitted due to same as L-ch.
• SIGNAL PATH
: CD PLAY (ANALOG OUT)
: CD PLAY (DIGITAL OUT)
19
19
A
(Page 21)
60
22
4
R
CD-L
72
TO MIRR/DFCT/
FOK DETECTOR
DIGITAL
OUT
SQSO
SQCK
SCOR
SENS
XLON
DATA
XLAT
CLOK
21
XRST
MDP
HOLD SW
OPTICAL PICK-UP BLOCK
(KSS-213DH)
PD
R-CH
(EXCEPT XG80 : Mexican/XG700)
CPU INTERFACE
AUTOMATIC
POWER
CONTROL
Q101
RETURN
F I-V AMP
E I-V AMP
DJ MIX
L
ASYO
SERIAL
IN
INTERFACE
R
HCD-XG80/XG700
BLOCK DIAGRAM – TUNER/TAPE DECK Section –
DECK PROCESS,
DECK A/B SELECT, PB/REC EQ AMP,
DOLBY NR AMP, ALC, AMS
IC301
RV311
• R-ch is omitted due to same as L-ch.
• SIGNAL PATH
PB LEVEL (L)
(DECK A)
HP101
(PLAYBACK)
: TUNER (FM/AM)
DOLBY PASS
70
53
RV301
R-CH
PB EQ AMP
(DECK B)
IC601 (1/2)
R-CH
+
L.P.F.
ALC
BUFFER
BIAS
CONTROL
CIRCUIT
MAOUT
28
17 19 15 16 18 20 22 23 24 25
: PLAYBACK (DECK A)
: PLAYBACK (DECK B)
: RECORD
B
(Page 21)
R-CH
B IN (R)
A 120/70
B NORM/CROM
ALC ON/OFF
PB A/B
NORM/HIGH
BIAS ON/OFF
RM ON/OFF
NR ON/OFF
REC/PB/PASS
LM ON/OFF
L-CH
PB EQ AMP
(DECK B)
IC601 (2/2)
R-CH
A IN (R)
BIAS (N)
33
BIAS (C)
32
BIAS (M)
31
PB LEVEL (L)
(DECK B)
HRPE101 (1/2)
(RECORD/PLAYBACK)
120
43 44
35
34
EQ IN (L)
51
B IN (L)
PB-L
40
DOLBY NR
AMP
CIRCUIT
REC OUT (L)
PB EQ AMP
(DECK A)
IC611 (1/2)
46
A IN (L)
ALC
IN (L)
48
R OUT (L)
R-CH
PB EQ AMP
(DECK A)
IC611 (2/2)
ALC (L)
L-CH
PB OUT (L)
R IN (L)
7-2.
39
REC
EQ AMP
EQ OUT
(L)
36
38
27
MSIN
RV301
AMS
CIRCUIT
REC LEVEL (L)
(DECK B)
MSOUT
REC-L
26
C
(Page 21)
REC/PB SWITCHING
IC602
S1004
(DECK A 120/70)
1
3
R-CH
R-CH
S1008
(DECK B 120/70)
4
2
C331, L331
BIAS
TRAP
76
B-TRG
CAP-M-H/L
90
87
86
88
89
SYSTEM CONTROLLER
(CD MECHANISM CONTROL)
IC501 (2/4)
RDS-DATA
RDS-INT
91
ST-DIN
ST-DOUT
ST-CLK
ST-CE
77
Q335
ST-MUTE
STEREO
TUNED
FM/AM TUNER UNIT
72
85 84 83 82 81 80 79 78
B-HALF
COAXIAL
FM 75Ω
73
100
B-SHUT
(XG700)
TRIGGER
PLUNGER DRIVE
(DECK B)
Q331, 332
A-SHUT
BIAS OSC
Q621, 622
TRIGGER
PLUNGER DRIVE
(DECK A)
Q333, 334
A-HALF
BIAS OSC
T621
HRPE101 (2/2)
(ERASE)
RV1002
TAPE SPEED
(NORMAL)
CAPSTAN MOTOR
CONTROL SWITCH
Q1001
ROTATION
DETECT SENSOR
(DECK B)
IC1002
AMS-IN
A+7V
TRIGGER PLUNGER
DECK B
A-TRG
REC BIAS
SWITCH
Q623
TRIGGER PLUNGER
DECK A
ROTATION
DETECT SENSOR
(DECK A)
IC1001
ALC
PB-A/B
EQ-H/N
BIAS
B-PLAY-SW
REC-MUTE
NR-ON/OFF
R/PB/PAS
TC-MUTE
RV341
REC BIAS (L)
(DECK B)
A-PLAY-SW
RV441
REC BIAS (R)
(DECK B)
TC-RELAY
R-CH
RV1001
TAPE SPEED
(HIGH)
49 50 51
54 53 55 52
21 20
CAPM-CNT2 74
(XG700)
ST-L
FM ANT
ST-R
AM ANT
AM
AM ANT
ANTENNA
ST-MUTE
STEREO
TUNED
ST-DIN
ST-DOUT
ST-CLK
ST-CE
(XG700)
RDS-DATA
RDS-INT
R-CH
ST-MUTE
STEREO
TUNED
ST-DIN
ST-DOUT
ST-CLK
ST-CE
S1003
(DECK A HALF)
D+5V
(UNSW)
S1001
S1002
(DECK A PLAY) (DECK B PLAY)
S1006
(DECK B HALF)
RDS-DATA
RDS-INT
FM ANT
ST-DIN
ST-DOUT
ST-CLK
ST-CE
FM
75Ω
ST-MUTE
STEREO
TUNED
(XG80)
S1005
(DECK A REC)
S1009
(DECK B REC)
RDS-DATA
RDS-INT
CT-L
20
20
D
(Page 21)
CAPSTAN
MOTOR DRIVE
Q336, 339
M
M1
(CAPSTAN)
HCD-XG80/XG700
7-3.
BLOCK DIAGRAM – MAIN Section –
(Page 22)
DISTORTION
ON/OFF SWITCH
Q880 – 883
DISTORTION
E
GUITAR AMP
IC853
J802
GUITAR
REC-L
GUITAR AMP
IC852
MIC AMP
IC850 (2/2)
SPEANA
+
C
(Page 20)
F
(Page 22)
RV601
GUITAR LEVEL
MD OUT
D
J701 (1/2)
L
VIDEO
AUDIO IN
R-CH
PHONO
EQ AMP
IC601
L
REC A2
REC B2
41
KEY OUT 1
KEY OUT 2
VOL
IN2
36
CPU
INTERFACE
COMMAND
30
J701 (2/2)
72
BUF
OUT2
BASS BOOST
CONTROL
CIRCUIT
VOLUME
CONTROL
33 32 34
M901
(FAN)
FAN MOTOR
DRIVE
Q961, 962
38, 39
M
37
6
59
FEED BACK
SWITCH
Q112
60 5
R-CH
TM401
FRONT SPEAKER
IMPEDANCE
USE 4 – 16Ω
D803
+
DBFB CONTROL
SWITCH
Q111
–1
+
R-CH
L
L
R-CH
R
FUNCTION SELECT
SWITCH
IC181
12
L
14
R
R-CH
11 XC-OUT
X501
32.768kHz
X0
X
X1
10 XC-IN
13
493-DATA 47
493-CLK 48
493-LAT 38
DBFB-H/L 7
SW-MODE 34
R-CH
PROTECT
SWITCH
Q804
D807
MUTING
Q113
R-CH
VOUT
10
MUTING CONTROL
SWITCH
Q802, 803
HEADPHONE
MUTING
Q805, 855
TH831
STANDBY SWITCH
Q803, 804, 834
TEMPERATURE
DETECT SWITCH
Q831, 832
CTLA
CTLB
CTLC
2 3 5
A B C
A B C
28 V MUTE
OVER LOAD
DETECT
Q801, 851
R-CH
RESET
SWITCH
Q801
+
DC DETECT
SWITCH
Q433, 434
R-CH
PROTECT 27
F-RELAY
D401
OVER LOAD
DETECT SWITCH
Q432
OVER LOAD
DETECT SWITCH
Q437
RY401
PROTECT SWITCH
Q431
PROTECT SWITCH
Q439
VIDEO OUT
• R-ch is omitted due to same as L-ch.
• SIGNAL PATH
: TUNER (FM/AM)
J803
PHONES
MUTING CONTROL
SWITCH
Q833
EVER +5V
RESET SIGNAL
GENERATOR
IC801
LINE-MUTE 6
AC-CUT 22
RESET 12
J702 (2/2)
R-CH
D534
POWER AMP
IC801
LOGIC
VIDEO SELECT
SWITCH,
VIDEO AMP
IC191
R
–
D501
STK-POWER 1
HP MUTE 93
IN1
1
IN3
6
+
R-CH
46 FUNC SEL0
45 FUNC SEL1
VIDEO
AUDIO IN
–
–2
R-CH
X502
16MHz
J702 (1/2)
J804 (1/2)
BASS WOOFER
CONTROL SWITCH
Q115
13 X-OUT
A B
10 9
15 X-IN
SYSTEM CONTROLLER
(CD MECHANISM CONTROL)
IC501 (3/4)
GAME
INPUT
VIDEO
42
R-CH
L+R
+
F OUT2
R-CH
R
J804 (2/2)
GAME
INPUT
AUDIO
SOUND
CONTROL
CIRCUIT
KEY IN2
KEY IN1
R
PHONO
IN
+
R-CH
MD IN
GRAPHIC
EQUALIZER
CONTROL
CIRCUIT
+
SUPER
WOOFER
+
BUF IN2
ST-L
INPUT SELECT SWITCH,
GRAPHIC EQUALIZER CONTROL,
ELECTRICAL VOLUME
IC101
IN D2
IN C2
IN B2
INPUT
IN E2
SELECT
SWITCH
IN A2
IN F2
57
BB B2,
BB A2
(Page 20)
66
67
68
65
69
64
PB-L
58
LATCH
B
2
CLOCK
(Page 20)
CD-L
RV602
MIC LEVEL
R
R-CH
R-CH
DATA
A
MIC AMP
IC850 (1/2)
MIC IN
J801
MIX MIC
(Page 19)
L
FRONT SPEAKER PROTECT
RELAY DRIVE
Q401, 402
3
HP-IN 36
RESET
: CD PLAY
: TAPE PLAY
: RECORD
: MIC INPUT
21
21
G
(Page 22)
HCD-XG80/XG700
BLOCK DIAGRAM – DISPLAY/KEY CONTROL/POWER SUPPLY Section –
28 , 27
SEG-1 – SEG-23
GR-15, GR-16
42, 40 – 29
GRID DRIVE
Q605, 606
BPF 0 17
BPF 1 18
BPF 2 19
BPF 3 20
BPF 4 21
ALL BAND 22
GR-2 – GR-14
FLUORESCENT INDICATOR TUBE
FL601
44 – 46
RESET 73
F02
F03
F04
F05
F06
DET
11
LINE
IN
B.P.F.
E
DISTORTION
(Page 21)
G
SUB POWER
TRANSFORMER
T901
EVER +5V
SYSTEM CONTROLLER (IC501) ,
FL DRIVER (IC601) B+
+5V
REGULATOR
IC901
RECT
D902 – 905
4
POWER
TRANSFORMER
T951
REC
LEVEL
REC IN
DET
TO FLUORESCENT
INDICATOR TUBE
(FL601)
6
VF
VF
+VL
–VL
POWER AMP (IC801),
PROTECT CIRCUIT
GUITAR DISTORTION 16
LED SEL
GRID DRIVE
Q607
BAND-PASS FILTER
IC602
16
15
14
13
12
(Page 21)
F
RESET
FLUORESCENT INDICATOR TUBE DRIVER,
KEY CONTROL
IC601
(Page 21)
SPEANA
7-4.
7
+VH
–VH
RECT
D832
RECT
D831
43 GR-1
LED DRIVER
IC701
B+ SWITCH
Q602, 603
VOLTAGE
SELECTOR
S901
+5V (LED)
LED SCK
LED LATCH
5
3
6
13 DATA
14 CLK
15 STB
S608
4
KEY POWER ON/OFF
2
KEY POWER
SAVE/DEMO
S609
POWER
SAVE/DEMO
(STANDBY)
S763
(JOG DIAL)
1
74 JOG A
ROTARY
ENCODER
S736
9
CD A+5V (SW) ,
CD D+5V (SW)
CD MECHANISM
DECK SECTION
B+
D611 – 614, 621, 622,
D700 – 710, 713 – 719,
D741, 791
LED DRIVE
Q601
RECT
D841 – 844
Q914
RECT
D833 – 836
I2C DATA 78
I2C CLK 79
B+ SWITCH
Q911, 912
+5V
REGULATOR
IC911
A+7V
B+ SWITCH
Q901, 902
+7V
REGULATOR
IC901
A–7V
B– SWITCH
Q903 – 905
–7V
REGULATOR
IC951
ST +10V
(FM/AM TUNER UNIT B+)
TUNER
B+ SWITCH
Q931, 932
D601
SYSTEM CONTROLLER
CD MECHANISM
CONTROL
IC501 (4/4)
30 IIC-DATA
29 IIC-CLK
75 JOG B
TC, PANEL,
AUDIO
CD-POWER
5
Q906
WAKE UP
VOL A
10 VOL B
8
18 WAKE UP
XIN
D-SW 80
XOUT
S736
VOLUME
72
70
S742
LID (CD)
OPEN/CLOSE
POWER
+10V
REGULATOR
IC931
2
FAN MOTOR B+
TC M+12V
(TC MOTOR SECTION B+)
X601
12.5MHz
CD M+7V
(CD MOTOR SECTION B+)
STBY RELAY 43
22
22
AC IN
–35V
REGULATOR
Q903, 908
B+ SWITCH
Q913
AU D+5V
M62493FP (IC101) B+
D+5V (SW)
(CD SENSOR SECTION B+)
SIRCS
ROTARY
ENCODER
S763
–35V
FL DRIVER (IC601)
B–
+5V (LED)
(PANEL SECTION B+)
D+5V (UNSW)
(RDS SECTION B+)
LED STANDBY 77
REMOTE CONTROL
RECEIVER
IC702
17, 19 – 23, 1 – 4, 7 – 11
11 – 15
KEY 0 – KEY 4
LED DAT
P1 – P6, P7 – P10, P12 – P16
Q604
S601 – 607, 611 – 619, 621 – 627,
S701 – 710, 712 – 732, 741, 743 – 757
(S632 : XG700)
EXCEPT
XG80 : Mexican
/XG700
+7V
REGULATOR
IC933
+12V
REGULATOR
IC932
RY901
POWER ON/OFF
RELAY DRIVE
Q901
HCD-XG80/XG700
7-5.
• Circuit Boards Location
NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
Q
These are omitted.
B E
•
•
•
•
•
Q
B C
•
•
E
These are omitted.
Q
B
C
E
These are omitted.
SUB TRANS board
TUNER PACK
(FM/AM TUNER UNIT)
PANEL FL board
PANEL VR board
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
• Indication of transistor.
C
TRANS board
•
MAIN board
A : B+ Line.
B : B– Line.
H : adjustment for repair.
Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
Circled numbers refer to waveforms.
Signal path.
F : TUNER (FM/AM)
E : TAPE PLAY (DECK A)
d : TAPE PLAY (DECK B)
G : RECORD
J : CD PLAY (ANALOG OUT)
c : CD PLAY (DEGITAL OUT)
N : MIC INPUT
Abbreviation
AR
: Argentina model
E2
: 120 V AC area in E model
EA
: Saudi Arabia model
MX
: Mexican model
SP
: Singapore model
ILLUMINATION board
PA board
TC-A board
MIC board
CD-L board
HEADPHONES board
TC-B board
CD-R (2) board
CD-R (1) board
FRONT INPUT board
LEAF SW board
TABLE SENSOR board
BD board
AUDIO board
CD MOTOR board
LED board
23
23
HCD-XG80/XG700
7-6.
PRINTED WIRING BOARD – BD Board –
• See page 23 for Circuit Boards Location.
(
)
TP(GND)
(
TP(VC)
)
(
)
TP(RF)
TP
(AGCCON)
TP(FE)
TP(TE)
MAIN BOARD
CN411
TP(FE1)
(Page 34)
19
21 , 31
21 , 31
21 , 31
21 , 31
KSS-213DH
• Semiconductor
Location
• Semiconductor
Location
Ref. No.
Q101
Location
Ref. No.
C-3
IC101
IC102
IC103
24
24
Location
C-2
B-1
B-1
HCD-XG80/XG700
7-7.
SCHEMATIC DIAGRAM – BD Board –
• See page 35 for Waveforms.
• See page 47 for IC Block Diagrams.
2.2
OPTICAL PICK-UP
BLOCK
(KSS-213DH)
D+5V (SW)
L-CH
R-CH
A+5V (SW)
CD-DATA
MAIN
BOARD
CN411
(Page 32)
CD-CLK
SQ-DATA
SQ-CLK
M+7V (UNSW)
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD STOP
(
) : CD PLAY
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
25
25
HCD-XG80/XG700
7-8.
PRINTED WIRING BOARDS – CD MOTOR Section –
• See page 23 for Circuit Boards Location.
B
MAIN BOARD
CN412
(Page 34)
26
26
HCD-XG80/XG700
SCHEMATIC DIAGRAM – CD MOTOR Section –
• See page 47 for IC Block Diagram.
TABLE MOTOR DRIVER
4.8
4.8
LED DRIVE
TRAY
7-9.
B
(Page 32)
MAIN BOARD
CN412
DISC TABLE SENSOR
4.8
4.8
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : CD STOP
27
27
HCD-XG80/XG700
7-10. PRINTED WIRING BOARD – AUDIO Board –
1
• See page 23 for Circuit Boards Location.
2
3
4
5
(Page 34)
AUDIO BOARD
C
6
7
8
MAIN BOARD
CN303
A
9
1
E
1
4
E
1
4
8
5
E
6
1
4
3
3
8
B
5
3
6
4
5
1
1
7
2
4
2
24
1-675-753-
(CHASSIS)
– B DECK –
HPRE101
RECORD/PLAYBACK
ERASE
C
1
2
L-CH
3
4
R-CH
– A DECK –
HP101
(PLAYBACK)
5
6
7
• Semiconductor
Location
Ref. No.
Location
IC601
IC602
IC611
B-2
B-3
B-8
Q621
Q622
Q623
B-5
B-5
B-6
28
28
1
2
L-CH
3
4
R-CH
(24)
HCD-XG80/XG700
7-11. SCHEMATIC DIAGRAM – AUDIO Board –
• See page 47 for IC Block Diagram.
PB EQ AMP
(DECK A)
(PALYBACK)
PB LEVEL (L)
(DECK A)
R492 1.5K
–7
R491 820
PB EQ AMP
(DECK B)
PB LEVEL (L)
(DECK B)
R482 1.5K
NC
A+7.5V
–7
APB-LCH
APB-RCH
R481 820
AGND
BPB-LCH
BPB-RCH
A–7.5V
C
MAIN BOARD
CN303
–VBIAS (–7.5V)
+VBIAS (+7.5V)
(Page 32)
BREC-RCH
BREC-LCH
SWITCHING
TC-HEAD-GND
6.9
REC BIAS (R)
(DECK B)
REC BIAS (L)
(DECK B)
REC BIAS
–6.5
6.9
–6.5
T621
BIAS OSC
–6.5 (–7.2)
–6.5
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : TAPE PLAY
(
) : RECORD
29
29
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
HCD-XG80/XG700
7-12. PRINTED WIRING BOARD – LEAF SW Board –
DECK A
PLUNGER
4
(
• See page 23 for Circuit Boards Location.
DECK B
PLUNGER
)
3
4
3
1
2
1
2
(DECK B 120/70)
(DECK A PLAY)
(DECK B REC)
(DECK B PLAY)
(DECK B HALF)
11
(DECK A HALF)
(DECK A 120/70)
11
(DECK A REC)
1-676-219-
D
MAIN BOARD
CN304
(Page 34)
7-13. SCHEMATIC DIAGRAM – LEAF SW Board –
CONTROL SWITCH
(CAPSTAN)
7.5k
DECK B
PLUNGER
DECK A
PLUNGER
* (3.7)
ROTATION DETECT SENSOR
(DECK A)
4.5 (*)
ROTATION DETECT
SENSOR (DECK B)
CAPM–
CAPM+
(DECK A 120/70)
CAPM–H/L
A–TRGM
TRGM–GND
(DECK A HALF)
B–TRGM
A–SHUT
DGND
(DECK A REC)
A–HALF
+5V
(DECK B HALF)
MAIN BOARD
CN304
B–SHUT
(Page 32)
A–PLAY
B–HALF / REC–A / REC–B
(DECK B REC)
B–120/70
B–PALY
NC
(DECK B 120/70)
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : TAPE PLAY (DECK A)
(
) : TAPE PLAY (DECK B)
: Impossible to measure
∗
(DECK A PLAY)
30
30
(DECK B PLAY)
D
A–120/70
HCD-XG80/XG700
7-14. SCHEMATIC DIAGRAM – MAIN Board (1/3) –
• See page 47 for IC Block Diagram.
(Page 33)
(Page 32)
(Page 32)
(Page 39)
(Page 32)
(Page 33)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER (FM/AM)
(
) : VIDEO
31
31
HCD-XG80/XG700
7-15. SCHEMATIC DIAGRAM – MAIN Board (2/3) –
• See page 35 for Waveforms.
(Page 33)
(Page 31)
(Page 33)
(Page 31)
(Page 41)
(Page 25)
(Page 27)
(Page 33)
(Page 30)
(Page 29)
(Page 33)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER (FM/AM)
(
) : CD PLAY
<
{
[
> : VIDEO
} : TAPE PLAY (DECK A)
] : TAPE PLAY (DECK B)
(Page 31)
〈〈
∗
〉〉 : RECORD
: Impossible to measure
32
32
HCD-XG80/XG700
7-16. SCHEMATIC DIAGRAM – MAIN Board (3/3) –
(Page 32)
(Page 39)
(Page 31)
(Page 32)
(Page 32)
(Page 37)
(Page 32)
(Page 31)
(Page 37)
33
33
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER (FM/AM)
(
) : CD PLAY
HCD-XG80/XG700
7-17. PRINTED WIRING BOARD – MAIN Board –
1
2
• See page 23 for Circuit Boards Location.
3
4
5
6
7
J705
RETURN
R
SEND
L
9
10
11
12
13
14
J701
DJ MIX
A
8
R
PHONO IN
L
R
MD IN
L
R
VIDEO
AUDIO IN
MD OUT
L
R
L
R
M901
(FAN)
J702
VIDEO
VIDEO IN
L
M
VIDEO OUT
(Page 38)
1
3
1
3
IC781
FRONT INPUT
BOARD
NO801
E
MAIN BOARD
CD DIGITAL OUT
OPTICAL
3
1
E
B
E
(AEP, UK, MX)
8
5
1
4
3
(CHASSIS)
1
C
5
E
1
E
E
E
E
E
(E2, EA, SP, AR)
D
1
E
3
E
(AEP, UK)
(XG700)
COAXIAL
FM 75Ω
E
E
E
*
FM 75Ω
U
ANTENNA
FM/AM
TUNER
UNIT
U
AM
(XG80)
E
* SUPPLIED AS
E
THE ASSEMBLED
BLOCK
E
F
1
1
E
3
E
(XG700)
K
PA BOARD
CN803
1
E
H
G
MIC BOARD
CN811
(Page 36)
4
(Page 38)
E
13
E
1
1
3
E
C
H
AUDIO BOARD
CN601
51
50
1
J
(Page 28)
PA BOARD
CN804
31
E
30
3
3
1
(Page 36)
(XG700)
80
81
(XG80)
13
I
100
1
3
1
3
1
E
E
1
3
3
1
E
E
D
J
E
E
LEAF SW BOARD
CN1001
(Page 30)
E
E
E
E
18
19
2
1
9
1
E
E
11
1-680-166-
G
PANEL FL BOARD
CN601
(Page 40)
A
34
34
BD BOARD
CN101
(Page 24)
B
CD MOTOR BOARD
CN201
(Page 26)
(11)
HCD-XG80/XG700
• Semiconductor
Location
Ref. No.
Location
D191
D192
D193
D194
D501
D534
D801
D802
D803
D804
D805
D806
D807
D808
D911
D912
D913
D931
D951
C-8
C-8
B-8
C-8
J-8
H-8
J-8
I-9
I-9
J-9
I-9
I-8
J-10
J-7
F-11
G-11
G-11
H-11
C-12
IC101
IC181
IC191
IC301
IC501
IC601
IC781
IC801
IC901
IC911
IC931
IC932
IC933
IC951
E-5
C-7
C-8
H-4
H-7
C-3
B-13
J-9
D-12
F-11
H-12
H-12
I-12
C-12
Q111
Q112
Q113
Q115
Q161
Q162
Q163
Q165
Q331
Q332
Q333
Q334
Q335
Q336
Q339
Q801
Q802
Q803
Q804
Q901
Q902
Q903
Q904
Q905
Q906
Q911
Q912
Q913
Q914
Q931
Q932
Q961
Q962
E-7
E-7
E-7
E-6
E-6
F-6
F-6
F-5
J-4
J-4
J-4
J-4
J-5
J-4
J-5
I-8
J-10
J-10
I-10
D-13
C-13
C-12
C-12
C-13
C-13
G-11
F-11
G-11
G-11
H-11
H-11
B-12
B-12
• Waveforms
– BD Board –
– MAIN Board –
5 IC101 wh (MDP) (CD Play Mode)
1 IC101 yj (XTAO)
2.5 Vp-p
3.1 Vp-p
7.8 µs
59 ns
2 IC101 ta (RFAC) (CD Play Mode)
1.8 Vp-p
30.5 µs
6 IC103 qh (RFO) (CD Play Mode)
1.2 Vp-p
1 IC501 0 (XC-IN)
2 IC501 qg (X-IN)
1.3 Vp-p
1.8 Vp-p
62.5 ns
3 IC101 ra (TE) (CD Play Mode)
– PANEL FL Board –
1 IC601 u; (XIN)
0.2 Vp-p
3.7 Vp-p
80 ns
4 IC101 el (FE) (CD Play Mode)
0.5 Vp-p
35
35
HCD-XG80/XG700
7-18. PRINTED WIRING BOARD – PA Board –
• Semiconductor
Location
Ref. No.
1
2
• See page 23 for Circuit Boards Location.
3
4
D-4
C-8
B-9
B-9
D-5
E-6
F-6
C-4
C-6
H-2
F-2
E-2
E-2
F-2
C-2
C-2
C-2
D-2
D-5
F-6
G-2
I-4
J-4
J-3
I-3
J-3
I-2
I-2
IC801
IC901
D-7
J-2
Q401
Q402
Q431
Q432
Q433
Q434
Q437
Q439
Q801
Q803
Q804
Q805
Q831
Q832
Q833
Q834
Q851
Q855
Q901
Q903
Q908
B-7
B-8
H-5
H-4
H-4
H-4
H-4
I-4
D-5
G-5
F-5
D-3
B-5
B-5
C-4
C-5
E-5
D-3
J-4
J-2
J-2
6
(Page 34)
Location
D401
D402
D405
D406
D801
D802
D803
D804
D805
D831
D833
D834
D835
D836
D841
D842
D843
D844
D851
D852
D853
D902
D903
D904
D905
D906
D911
D912
5
J
7
8
9
10
(Page 34)
K
MAIN BOARD
CN902
MAIN BOARD
CN901
A
13
1
13
1
PA BOARD
(XG700)
E
E
B
(Page 38)
–2
1
N
E
HEADPHONES
BOARD
CN802
E
–1
4
(CHASSIS)
C
E
–
(XG80)
R
+
E
E
TM401
FRONT SPEAKER
IMPEDANCE
USE 4 – 16Ω
E
22
–
L
+
(XG80)
D
+
E
+
E
E
1
F
E
(Page 46)
1
11
E
M
G
TRANS
BOARD
CN952
1
3
L
11
TRANS
BOARD
CN951
1-680-173-
(Page 46)
1
E
H
E
E
E
E
4
E
I
1
E
Q
E
4
(CHASSIS)
(Page 46)
B
C
J
E
SUB TRANS
BOARD
NO903
3
1
36
36
(11)
HCD-XG80/XG700
7-19. SCHEMATIC DIAGRAM – PA Board –
(Page 39)
(Page 46)
(Page 46)
(Page 46)
(Page 33)
(Page 33)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
37
37
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER (FM/AM)
HCD-XG80/XG700
7-20. PRINTED WIRING BOARDS – MIC/FRONT INPUT/HEADPHONES Boards –
1
2
3
• See page 23 for Circuit Boards Location.
4
5
6
7
8
9
10
MIC BOARD
A
(Page 44)
R
E
E
8
Ref. No.
1
H
E
E
MAIN BOARD
CN452
(Page 34)
1
8
B
• Semiconductor
Location
TC-A BOARD
NO805
1
1
2
4
3
5
6
8
7
1
2
4
3
5
6
8
7
6
J802
Location
IC850
IC852
IC853
C-4
B-4
A-3
Q880
Q881
Q882
Q883
B-2
A-1
B-2
A-2
GUITAR
9
1
4
CN811
J801
8
C
1
MIX MIC
9
1
3
1-680-182-
11
(11)
FRONT INPUT BOARD
D
VIDEO
(Page 36)
N
E
PA BOARD
CN806
HEADPHONES BOARD
J804
GAME
INPUT
L
J803
1
PHONES
AUDIO
R
3
1
6
1
8
6
5
3
4
2
1
9
F
11
(11)
1-680-180-
E
7
4
MAIN BOARD
CN702
(Page 34)
(CHASSIS)
38
38
11
1-680-181-
(11)
HCD-XG80/XG700
7-21. SCHEMATIC DIAGRAM – MIC/FRONT INPUT/HEADPHONES Boards –
(Page 45)
(Page 33)
(Page 31)
(Page 37)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER (FM/AM)
39
39
HCD-XG80/XG700
7-22. PRINTED WIRING BOARD – PANEL FL Board –
1
2
• See page 23 for Circuit Boards Location.
3
4
5
6
7
8
9
10
11
12
13
PANEL FL BOARD
A
1
3
6
28
34
FL601
FLUORESCENT
INDICATOR TUBE
49
52
54
E
D601, S608
B
I/1
E
TIMER
SELECT
E
E
POWER SAVE/DEMO
(STANDBY)
E
FUNCTION
E
SLEEP
DISPLAY
10
18
C
E
1
9
c/CLOCK SET
GAME
SPECTRUM
ANALYZER
1
3
D
11
1-680-169-
U
G
10
1
MAIN BOARD
CN431
S601 – 609
PANEL VR
BOARD
CN701
T
(Page 42)
TC-B BOARD
NX601
(Page 44)
• Semiconductor
Location
Ref. No.
Location
D601
D602
D603
B-13
B-4
B-12
IC601
IC602
C-7
C-10
Q601
Q602
Q603
Q604
Q605
Q606
Q607
B-12
B-4
C-4
C-4
B-9
B-8
B-8
TC-A BOARD
NX602
(Page 44)
(Page 34)
E
S
40
40
(11)
HCD-XG80/XG700
7-23. SCHEMATIC DIAGRAM – PANEL FL Board –
• See page 35 for Waveform.
• See page 47 for IC Block Diagram.
(Page 45)
(Page 45)
(Page 32)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER (FM/AM)
(Page 43)
41
41
HCD-XG80/XG700
1
2
3
• See page 23 for Circuit Boards Location.
4
5
6
7
8
9
10
11
(Page 40)
U
A
12
13
ILLUMINATION
BOARD
PANEL FL
BOARD
CN602
4
3
PANEL VR BOARD
3
1
2
1-680-167-
7-24. PRINTED WIRING BOARDS – PANEL VR/ILLUMINATION Boards –
11
(11)
D791
(ILLUMINATION)
1
(CHASSIS)
1
D717, S713
4
B
GROOVE
S736
ROTARY ENCODER
D708, S719
VOLUME
DANCE
3
1
D706, S717
D710, S721
JAZZ
SALSA
D704, S716
D702, S727
GUITAR
ROCK
D718, S714
b
B
SUPER WOOFER
C
v
D709, S722
GAME
D707, S720
TANGO
D701, S728
MOVIE
D705, S718
SAMBA
V
D719, S712
S715
SURROUND
SUPER WOOFER MODE
D703, S729
11
REGGAE
D714, S708
1-680-170-
ENTER
(CHASSIS)
P. FILE
FLAT
S701 – 710,
S712 – S732
D
MIC GUITAR/
KARAOKE
(AEP, UK)
D716, S702
ENTER/NEXT
S707
PTY
TUNING
MODE
+
–
S706
STEREO/MONO
D713, S704
TUNER/BAND
• Semiconductor
Location
Ref. No.
Location
D701
D702
D703
D704
D705
D706
D707
D708
D709
D710
D713
D714
D715
D716
D717
D718
D719
D791
C-10
C-10
C-9
C-9
C-8
C-8
C-7
C-7
C-6
C-6
D-7
D-4
D-10
D-9
B-13
C-13
C-12
A-11
IC701
IC702
D-10
A-11
42
42
TUNER/MEMORY
S701
D715, S731
GUITAR DISTORTION
(11)
HCD-XG80/XG700
7-25. SCHEMATIC DIAGRAM – PANEL VR/ILLUMINATION Boards –
• See page 47 for IC Block Diagram.
(Page 41)
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : TUNER (FM/AM)
43
43
HCD-XG80/XG700
7-26. PRINTED WIRING BOARDS – TC-A/TC-B/CD-L/CD-R (1)/CD-R (2) Boards – • See page 23 for Circuit Boards Location.
1
2
3
4
5
A
T
PANEL FL
BOARD
NO602
B
8
9
10
PANEL FL
BOARD
NO601
CD-L BOARD
TC-B BOARD
TC-A BOARD
1
7
(Page 40)
(Page 40)
S
6
1
9
D621, S621
D622, S622
H
h
10
LID (CD)
OPEN/CLOSE
D612, S616
D611, S615
H
h
DISC 5
DISC 4
DISC 3
DISC 2
DISC 1
S741,
S743 – 750
LOOP
C
D741, S745
S611 – 619
. AMS >
M
m
M
x
. AMS >
x
m
EDIT
FLASH
NON-STOP
11
S621 – 627
1-680-177-
D614, S612
z REC
D613, S611
X
DIRECTION
DOLBY NR
(11)
CD-R (1) BOARD
D
RV601
GUITAR
LEVEL
S613
RV602
H SPEED DUB
MIC
LEVEL
12
1
1-680-171-
R
E
CD SYNC
11
(11)
11
7
1
1-680-172-
x
PLAY MODE
m
REPEAT
(11)
MIC BOARD
CN812
S763
ROTARY ENCODER
(JOG DIAL)
(Page 38)
D700, S751
HX
S751 – 757
1
M
DISC SKIP
1-680-178-
3
F
11
1-680-183-
CD-R (2) BOARD
• Semiconductor
Location
Ref. No.
D611
D612
D613
D614
D621
D622
D700
D741
Location
B-5
B-4
C-5
C-4
B-1
B-2
E-9
C-7
44
44
(11)
11
(11)
HCD-XG80/XG700
7-27. SCHEMATIC DIAGRAM – TC-A/TC-B/CD-L/CD-R (1)/CD-R (2) Boards –
(Page 41)
(Page 39)
(Page 41)
45
45
HCD-XG80/XG700
7-28. PRINTED WIRING BOARDS – TRANSFORMER Section–
• See page 23 for Circuit Boards Location.
7-29. SCHEMATIC DIAGRAM – TRANSFORMER Section –
1
L
PA BOARD
NO702
3
(Page 36)
4
(Page 37)
TRANS BOARD
1
(Page 37)
M
PA BOARD
CN801
(Page 36)
(MX)
1
T951
POWER
TRANSFORMER
(E2, EA, SP, AR)
(EXCEPT MX)
4
(Page 37)
* * NOT REPLACE:
BUILT IN TRANSFORMER
(E2, EA, SP, AR)
(AEP, UK)
11
1-680-174-
(11)
(E2, EA, SP, AR)
SUB TRANS BOARD
–2
(MX)
S901
–1
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
(AEP, UK)
VOLTAGE
SELECTOR
120V
R
220V
R
230V – 240V
T901
SUB POWER
TRANSFORMER
1
1
4
2
(E2, EA, SP, AR)
(AEP, UK, MX)
1
4
11
(E2, EA, SP, AR)
1-680-175-
Q
PA BOARD
CN904
1
(11)
2
(Page 36)
AC IN
46
46
HCD-XG80/XG700
• IC Block Diagrams
– BD Board –
VDD
VSS
AVDD3
PCO
FILI
FILO
CLTV
AVSS3
RFAC
BIAS
ASYI
ASYO
AVDD0
IGEN
AVSS0
ADIO
RFDC
CE
TE
CXD2587Q
DOUT
IC101
60
59 58 57
56 55 54 53
52
51 50 49 48
47
46 45
44
43 42 41
LRCK 61
D/A
INTERFACE
PCMD 62
ERROR
CORRECTOR
INTERNAL BUS
DIGITAL
OUT
DIGITAL
PLL
16K
RAM
40 SE
39 FE
38 VC
ASYMMETRY
CORRECTOR
OPERATIONAL
AMPLIFIER
ANALOG SWITCH
EFM
DEMODULATOR
A/D
CONVERTER
BCK 63
EMPH 64
XVDD 65
XTAI
XTAO
XVSS
AVDD1
AOUT1
AIN1
66
67
68
69
70
71
TIMING
LOGIC
CLOCK
GENERATOR
SERVO DSP
LOUT1 72
LOUT2 75
SUBCODE
PROCESSOR
PWM
PWM
AVSS1 73
AVSS2 74
RMUT 79
LMUT 80
TRACKING
SERVO
TRACKING
PWM GENERATOR
SLED
SERVO
SLED PWM
GENERATOR
SERVO
INTERFACE
OVER SAMPLING
DIGITAL FILTER
AIN2 76
FOCUS PWM
GENERATOR
26 MDP
25 LOCK
MIRR, DFCT,
FOK
DETECTOR
24 FOK
23 DFCT
22 MIRR
SERVO AUTO
SEQUENCER
C2PO
SCOR
SCLK
VDD
ATSK
SYSM
WFCK
XUGF
XPCK
GFS
9 10 11 12 13 14 15 16 17 18 19 20
4
SPOA
SPOB
XLON
5 6 7 8
DATA
XLAT
CLOK
SENS
XRST
21 COUT
CH4BIN
CH4SIN'
CH4SIN
CH3FIN
CH3RIN
CAPAIN3
GND
MUTE
POWVCC
CH3OUTR
CH3OUTF
CH4OUTR
CH4OUTF
BA5974FP-E2
PRFVCC
IC102
SQSO
SQCK
CPU
INTERFACE
3
FRDR
FFDR
TRDR
TFDR
SRDR
SFDR
DIGITAL
CLV
SERIAL IN
INTERFACE
1 2
33
32
31
30
29
28
27 SSTP
3rd ORDER
NOISE SHAPER
AOUT2 77
AVDD2 78
PWM GENERATOR
FOCUS
SERVO
37 XTSL
36 TES1
35 TEST
34 VSS
28
27
26
25
24
23
22
21
20
19
18
17
16
15
F
R
R
MUTE
INTERFACE
F
LEVEL SHIFT
THERMAL
SHUTDOWN
F
INTERFACE
F
R
F
R
INTERFACE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CH1RIN
CAPAIN1
CH2FIN
CH2RIN
CAPAIN2
GND
VREFIN
POWVCC
CH2OUTR
CH2OUTF
CH1OUTR
CH1OUTF
R
CH1FIN
R
VREFOUT
F
47
HCD-XG80/XG700
IC103
CXA2568M-T6
VCC
HOLD 1
VCC
APC PD AMP
+
–
24 VCC
23 LC/PD
APC LD AMP
VEE
22 LD ON
+
–
+
–
+
–
21 HOLD SW
20 AGC CONT
VEE
AGC VTH 2
50µA
LD 3
VCC
+
–
PD 4
19 RF BOT
VC
+
–
+
–
+
–
VC
A 5
+
–
B 6
VEE
18 RFTC
RF SUMMING AMP
C 7
+
–
VC
RF EQ AMP
VC
D 8
+
–
17 RF I
16 RF O
15 RFE
VC
FOCUS ERROR AMP
VEE
VEE 9
+
–
14 FE
VC
VC
+
–
F 10
–
+
–
+
E 11
TRACKING
ERROR AMP
VC
VC
VC BUFFER
VC 12
VC
48
+
–
VC
VEE
VCC
13 TE
HCD-XG80/XG700
– CD MOTOR Board –
IC201
TA8409S
VREF
BLOCK
STANDBY
BLOCK
HEAT
CUT OFF
BLOCK
1
IN2
2
VCC
3
OUT2
5
GND
4
NC
6
VS
7
OUT1
8
VREF
– AUDIO Board –
– MAIN Board –
µPC1330HA
IC602
9
IN1
IC191
BA7615N
MUTE
INVERTER
75Ω
8db
LOGIC
COMPARATER
8
9
2
3
6
4
5
7
– PANEL FL Board –
– PANEL VR Board –
IC602
IC701
R02
1
REFERENCE
CURRENT
R01
2
REFERENCE
CURRENT
LINE NF
3
LINE IN
4
–
+
RESET
BAND
PASS
FILTER
RESET C
BIAS C
GND
7
8
9
17
16
15
14
13
12
F01
F02
F03
F04
F05
F06
CONTROL
CIRCUIT
SHIFT REGISTER
LATCH CIRCUIT
–
+
11 REC LEVEL
10 VCC
OUTPUT CIRCUIT
1 2 3 4 5 6 7 8 9 10 11
12
SO
6
NJU3716L
P7
P8
P9
P10
P11
VSS
P12
P13
P14
P15
P16
5
REC IN
10
24 23 22 21 20 19 18 17 16 15 14 13
DET
REC NF
18 RESET
9
VDD
P6
P5
P4
P3
P2
VSS
P1
CLR
STB
CLK
DATA
BA3830F
8
VOUT
1
IN4
SW R2
CTLC
7
SW P2 GND
VCC
6
VCC
IN3
5
GND
IN2
SW P1 CONT
SW R1 GND
CTLC
4
CTLB
3
IN1
2
CTLA
1
49
HCD-XG80/XG700
7-30.
IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC501 M30622MAA-A92FP (SYSTEM CONTROLLER (CD MECHANISM CONTROL))
Pin No.
Pin Name
I/O
1
STK-POWER
O
Power amplifier on/off selection signal output “L”: standby mode, “H”: power amplifier on
2
POWER
O
Power on/off control signal output for the audio system (+5V) and deck, panel, audio system
(+7V) and FM/AM tuner unit (+10V) “L”: standby mode, “H”: power on
3
F-RELAY
O
Relay drive signal output for the front speaker protect “H”: relay on
4
REAR-RELAY
O
Relay drive signal output for the rear speaker protect “H”: relay on Not used (open)
5
CD-POWER
O
Power on/off control signal output for the CD mechanism deck section
“L”: standby mode, “H”: power on
6
LINE-MUTE
O
Line muting on/off control signal output “L”: muting on, “H”: muting off
7
DBFB-H/L
O
DBFB normal/high selection signal output to the M62493FP (IC101)
“L”: DBFB high, “H”: DBFB low (normal)
8, 9
—
—
Connect to ground
10
XC-IN
I
Sub system clock input terminal (32.768 kHz)
11
XC-OUT
O
Sub system clock output terminal (32.768 kHz)
12
RESET
I
System reset signal input from the reset signal generator (IC801) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
13
X-OUT
O
Main system clock output terminal (16 MHz)
14
VSS
—
Ground terminal
15
X-IN
I
16
VDD
—
17
NMI
I
Non-maskable interrupt input terminal Fixed at “H” in this set
18
WAKE UP
I
Wakeup control signal input from the fluorescent indicator tube driver (IC601) “L” active
19
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2587Q (IC101)
20
RDS-INT
I
Serial data transfer clock signal input from the RDS decoder on the FM/AM tuner unit
(Used for the HCD-XG700)
21
RDS-DATA
I
Serial data input from the RDS decoder on the FM/AM tuner unit
(Used for the HCD-XG700)
22
AC-CUT
I
AC off detection signal input from the reset signal generator (IC801) “L”: AC cut checked
23
PL-CLK
O
Serial data transfer clock signal output to the pro-logic circuit Not used (open)
24
PL-DATA
O
Serial data output to the pro-logic circuit Not used (open)
25
PL-LAT
O
Serial data latch pulse output to the pro-logic circuit Not used (open)
26
TIMER LED
O
LED drive signal output terminal Not used (open)
27
PROTECT
I
Protect on/off detection signal input from the speaker protect circuit
“L”: protect on, “H”: protect off
28
V MUTE
O
Video muting on/off control signal output to the BA7615N (IC191)
“L”: muting off, “H”: muting on
29
IIC-CLK
I/O
Communication data reading clock signal input or transfer clock signal output with the fluorescent
indicator tube driver (IC601)
30
IIC-DATA
I/O
Communication data bus with the fluorescent indicator tube driver (IC601)
31
NO-USE
O
Not used (open)
32
SQ-DATA
I
Subcode Q data input from the CXD2587Q (IC101)
33
SQ-CLK
I
Subcode Q data reading clock signal output to the CXD2587Q (IC101)
34
SW-MODE
O
Music/movie mode selection signal output to the M62493FP (IC101)
“L”: movie mode , “H”: music mode
35
CD-DATA
O
Serial data output to the CXD2587Q (IC101)
36
H/P IN
I
Connection detection signal input of the headphone jack (J803)
“L”: no connected, “H”: headphone connected
37
CD-CLK
O
Serial data transfer clock signal output to the CXD2587Q (IC101)
38
493-LAT
O
Serial data latch pulse output to the M62493FP (IC101)
50
Description
Main system clock input terminal (16 MHz)
Power supply terminal (+5V)
HCD-XG80/XG700
Pin No.
Pin Name
I/O
Description
39
CLOCK-OUT
O
Not used (open)
40, 41
NO-USE
O
Not used (open)
42
FL OFF
O
Filament on/off selection signal output for the fluorescent indicator tube (FL601)
“L”: filament off, “H”: filament on Not used in this set
43
STBY RELAY
O
Main power on/off control signal output “L”: standby mode, “H”: power on
44
BASS FREQ
O
Sync bass frequency normal/high selection signal output terminal
“L”: sync bass off (normal), “H”: sync bass high Not used (open)
45
FUNC SEL1
O
Function selection signal output to the BA7615N (IC191)
46
FUNC SEL0
O
Function selection signal output to the BA7615N (IC191)
47
493-DATA
O
Serial data output to the M62493FP (IC101)
48
493-CLK
O
Serial data transfer clock signal output to the M62493FP (IC101)
49
ST-MUTE
O
Tuner muting on/off control signal output to the FM/AM tuner unit
“L”: muting off, “H”: muting on
50
STEREO
I
FM stereo detection signal input from the FM/AM tuner unit “L”: stereo
51
TUNED
I
Tuning detection signal input from the FM/AM tuner unit “L”: tuned
52
ST-CE
O
PLL chip enable signal output to the FM/AM tuner unit
53
ST-DOUT
O
PLL serial data output to the FM/AM tuner unit
54
ST-DIN
I
PLL serial data input from the FM/AM tuner unit
55
ST-CLK
O
PLL serial data transfer clock signal output to the FM/AM tuner unit
56
SENS
I
Internal status detection monitor input from the CXD2587Q (IC101)
57
HOLD
O
Laser power control signal output to the CXA2568M (IC103)
58
XLT
O
Serial data latch pulse output to the CXD2587Q (IC101)
59
XRST
O
Reset signal output to the CXD2587Q (IC101) and BA5974FP (IC102) “L”: reset
60
DISC-SENS
I
Disc status detection signal input terminal Not used (fixed at “L”)
61
T-SENS
I
Disc table status detection signal input from the disc table sensor (IC202)
62
VDD
—
Power supply terminal (+5V)
63
TBL-L
O
Motor drive signal output to the table motor driver (IC201) “L” active *1
64
VSS
—
Ground terminal
65
TBL-R
O
Motor drive signal output to the table motor driver (IC201) “L” active *1
66
LOAD-OUT
O
Loading motor drive signal output terminal Not used (open)
67
LOAD-IN
O
Loading motor drive signal output terminal Not used (open)
68
ENC3/UP-SW
I
Detection signal input from the up switch (S201)
69
ENC2/DISC-LED
O
LED drive signal output of the DISC No. indicator (D201) “H”: LED on
70
ENC1
I
Disc tray address detection signal input terminal Not used (fixed at “L”)
71
OUT-OPEN
I
Disc tray open/close detection signal input terminal Not used (fixed at “L”)
72
B-TRG
O
Deck-B side trigger plunger drive signal output “H”: plunger on
73
A-TRG
O
Deck-A side trigger plunger drive signal output “H”: plunger on
74
CAPM-CNT2
O
Capstan motor (M1) drive signal output “L”: reverse direction, “H”: forward direction
75
CAPM-CNT1
O
Capstan motor drive signal output terminal Not used (open)
76
CAP-M-H/L
O
High/normal speed selection signal output of the capstan motor (M1)
“L”: normal speed, “H”: high speed
77
AMS-IN
I
Whether a music is present or not from HA12215F (IC301) is detected at automatic music sensor
“L”: music is present, “H”: music is not present
*1 Table motor (M201) control
Mode
Stop
Counterclockwise
Clockwise
Brake
TBL-L (pin yd)
“H”
“L”
“H”
“L”
TBL-R (pin yg)
“H”
“H”
“L”
“L”
Terminal
51
HCD-XG80/XG700
Pin No.
Pin Name
I/O
78
TC-MUTE
O
Line muting on/off selection signal output to the HA12215F (IC301)
“L”: muting off, “H”: muting on
79
R/PB/PAS
O
Recording/playback/pass selection signal output to the HA12215F (IC301)
“L”: recording mode, “H”: pass, “Hi-z”: playback mode
80
NR-ON/OFF
O
Dolby NR on/off selection signal output to the HA12215F (IC301)
“L”: dolby off, “H”: dolby on
81
REC-MUTE
O
Recording muting on/off selection signal output to the HA12215F (IC301)
“L”: muting on, “H”: muting off
82
BIAS
O
Recording bias on/off selection signal output to the HA12215F (IC301)
“L”: bias off, “H”: bias on
83
EQ-H/N
O
Normal/high speed selection signal output to the HA12215F (IC301)
“L”: normal speed, “H”: high speed
84
PB-A/B
O
Deck-A/B selection signal output to the HA12215F (IC301) “L”: deck-A, “H”: deck-B
85
ALC
O
Automatic limiter control signal output to the HA12215F (IC301) “L”: limiter on
86
B-PLAY-SW
I
Detection signal input from the deck- B play detect switch (S1002) “H”: deck-B play
87
A-PLAY-SW
I
Detection signal input from the deck- A play detect switch (S1001) “H”: deck-A play
88
A-HALF
I
Detection signal input from the deck-A cassette detect switch (S1003)
“L”: no cassette, “H”: cassette in
89
B-HALF
I
Detection signal input from the deck-B half detect switch (S1006)
90
B-SHUT
I
Shut off detection signal input from the deck-B side reel pulse detector (IC1002)
91
A-SHUT
I
Shut off detection signal input from the deck-A side reel pulse detector (IC1001)
92
SOFT-TEST
O
Output terminal for the software test (open)
93
HP MUTE
O
Headphone muting control signal output “L”: muting on, “H”: muting off
94
KEY/CD-ADJ
I
Setting terminal for the CD adjustment mode
95
MODEL-IN
I
Model setting terminal
96
AVSS
—
97
SPEC-IN
I
Destination setting terminal
98
VREF
I
Reference voltage (+5V) input terminal
99
AVCC
—
Power supply terminal (+5V) (for A/D conversion)
100
TC-RELAY
O
Recording/playback selection signal output to the REC/PB switch (IC602)
“L”: playback, “H”: recording
52
Description
Not used (fixed at “L”)
Ground terminal (for A/D conversion)
HCD-XG80/XG700
• PANEL FL BOARD IC601 TMP88CP76F-1B71 (FLUORESCENT INDICATOR TUBE DRIVER, KEY CONTROL)
Pin No.
Pin Name
I/O
Description
1
SIRCS
I
Remote control signal input from the remote control receiver (IC702)
2
KEY POWER
SAVE/DEMO
I
Power save/demonstration switch (S609 POWER SAVE/DEMO (STANDBY)) input terminal
“L” is input when key pressing
3
LED SCK
O
Serial data transfer clock signal output to the LED driver (IC701)
4
KEY POWER
ON/OFF
I
Power on/off switch (S608 I/1) input terminal “L” is input when key pressing
5
LED DAT
O
Serial data output to the LED driver (IC701)
6
LED LATCH
O
Serial data latch pulse signal output to the LED driver (IC701)
7
LED SEL
O
LED selection signal output
8
WAKE UP
O
Wakeup control signal output to the system controller (IC501) “L” active
9
VOL A
I
Jog dial pulse input from the rotary encoder (S736 VOLUME) (A phase input)
10
VOL B
I
Jog dial pulse input from the rotary encoder (S736 VOLUME) (B phase input)
11
KEY 0
I
Key input terminal (A/D input) S601 to S607, S727 to S732 (DISPLAY, SPECTRUM
ANALYZER, TIMER SELECT, SLEEP, c/CLOCK SET, GAME, FUNCTION, ROCK,
MOVIE, REGGAE, MIC GUITAR/KARAOKE, GUITAR DISTORTION, PTY) keys input
(S732 PTY key: used for the HCD-XG700)
12
KEY 1
I
Key input terminal (A/D input) S621 to S627, S743 to S750 (H, h, x, . AMS >
m/M, DOLBY NR, DIRECTION, FLASH, EDIT, NON-STOP, DISC1/2/3/4/5) keys input
13
KEY 2
I
Key input terminal (A/D input)
S615 to S619, S716 to S726 (h, H, x, . AMS > m/M, GUITAR, JAZZ, SAMBA,
DANCE, TANGO, SALSA, GAME, b, v, V, B) keys input
14
KEY 3
I
Key input terminal (A/D input)
S701 to S710, S712 to S715, S741 (TUNER MEMORY, ENTER/TEXT, –, TUNER/BAND, +,
STEREO/MONO, TUNING MODE, ENTER, P.FILE, FLAT, SURROUND, GROOVE, SUPER
WOOFER, SUPER WOOFER MODE, LOOP) keys input
15
KEY 4
I
Key input terminal (A/D input) S611 to S614, S751 to S757 (X, z REC, H SPEED DUB, CD
SYNC, HX, x, m, M, DISC SKIP, REPEAT, PLAY MODE) keys input
16
GUITAR
DISTORTION
O
Distortion on/off control signal output
17
BPF 0
I
Spectrum analyzer drive (super low frequency) signal input from the spectrum analyzer bandpass filter (IC602) (for 40 Hz)
18
BPF 1
I
Spectrum analyzer drive (low frequency) signal input from the spectrum analyzer band-pass filter
(IC602) (for 100 Hz)
19
BPF 2
I
Spectrum analyzer drive (low and middle frequency) signal input from the spectrum analyzer
band-pass filter (IC602) (for 400 Hz)
20
BPF 3
I
Spectrum analyzer drive (middle and high frequency) signal input from the spectrum analyzer
band-pass filter (IC602) (for 2 kHz)
21
BPF 4
I
Spectrum analyzer drive (high frequency) signal input from the spectrum analyzer band-pass filter
(IC602) (for 6 kHz)
22
ALL BAND
I
Spectrum analyzer drive signal input from the spectrum analyzer band-pass filter (IC602)
(for VACS, non-stop signal)
23
VSS
—
Ground terminal
24
VASS
—
Ground terminal (for A/D conversion)
25
VAREF
I
26
VDD
—
Power supply terminal (+5V)
27, 28
GR-16, GR-15
O
Grid drive signal output to the fluorescent indicator tube (FL601)
29 to 40
GR-14 to GR-3
O
Grid drive signal output to the fluorescent indicator tube (FL601)
41
VDD VFT
—
Power supply terminal (+5V)
42
GR-2
O
Grid drive signal output to the fluorescent indicator tube (FL601)
43
GR-1
O
Grid drive signal output to the fluorescent indicator tube (FL601)
Reference voltage (+5V) input terminal (for A/D conversion)
53
HCD-XG80/XG700
Pin No.
Pin Name
44 to 66 SEG-1 to SEG-23
54
I/O
Description
O
Segment drive signal output to the fluorescent indicator tube (FL601)
67
LED STANDBY
O
LED drive signal output of the I/1 indicator (D601) “H”: LED on
68
VKK
—
Power supply terminal (–35V) (for fluorescent indicator tube drive)
69
VDD
—
Power supply terminal (+5V)
70
XIN
I
71
VSS
—
Ground terminal
72
XOUT
O
System clock output terminal (12.5 MHz)
73
RESET
I
System reset signal input from the reset signal generator (IC801) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
74
JOG A
I
Jog dial pulse input from the rotary encoder (S763 JOG DIAL) (A phase input)
75
JOG B
I
Jog dial pulse input from the rotary encoder (S763 JOG DIAL) (B phase input)
76
TEST
I
Connected to ground
77
—
—
Not used (open)
78
I2C DATA
I/O
Communication data bus with the system controller (IC501)
79
I2C CLK
I/O
Communication data reading clock signal input or transfer clock signal output with the system
controller (IC501)
80
D-SW
I
System clock input terminal (12.5 MHz)
CD door open/close detection switch (S742) input terminal “L”: close, “H”: open
HCD-XG80/XG700
SECTION 8
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Abbreviation
AR : Argentina model
E2 : 120 V AC area in E model
EA : Saudi Arabia model
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
MX : Mexican model
SP : Singapore model
8-1. CASE, BACK PANEL SECTION
3
#1
5
#3
4
#2
XG80: MX/XG700
#3
6
#3
#3
#3
#3
not supplied
#3
#3
2
#3
#3
not supplied
#3
7
2
M901
Chassis section
#3
Front panel section
1
#3
Ref. No.
Part No.
Description
1
2
* 3
4
4
4-948-236-21
3-363-099-01
4-214-777-12
1-769-977-11
1-773-009-11
CUSHION (107)
SCREW (CASE 3 TP2)
CASE
WIRE (FLAT TYPE) (13 CORE) (XG80)
WIRE (FLAT TYPE) (15 CORE) (XG700)
5
5
5
1-693-484-11 TUNER (FM/AM) (E2)
1-693-488-11 TUNER (FM/AM) (EA, AR, SP, MX)
1-693-490-11 TUNER (FM/AM) (AEP, UK)
Remark
Ref. No.
Part No.
Description
6
7
7
7
7
1-535-706-21
4-232-088-01
4-232-088-11
4-232-088-21
4-232-088-31
PLUG, JUMPER (XG80: MX/XG700)
PANEL, BACK (AEP, UK)
PANEL, BACK (E2)
PANEL, BACK (SP)
PANEL, BACK (MX)
7
7
M901
4-232-088-41 PANEL, BACK (EA)
4-232-088-51 PANEL, BACK (AR)
1-763-072-11 FAN, D.C.
Remark
55
HCD-XG80/XG700
8-2. FRONT PANEL SECTION-1
72
73
TCM-230PWR42
#3
63
58
61
60
not supplied
64
#3
59
#3
65
not supplied
74
not
supplied
67
66
62
65
75
76
58
58
58
not
supplied
68
70
69
71
69
58
56
55
54
57
not
supplied
not supplied
77
53
52
58
78
not supplied
58
not supplied
51
Front panel section-2
Ref. No.
Part No.
Description
65
66
67
68
69
4-959-229-11
4-225-509-01
X-4952-465-1
4-225-510-01
4-224-104-11
DETENT, CASSETTE
HOLDER (DECK-A)
HOLDER (DECK-B) ASSY
HOLDER (DECK-B)
DAMPER
SPRING (TC EJECT), COIL
KNOB (MIC)
SCREW (2.6X8), +BVTP
COVER (EJECT)
LEVER (EJECT-A)
70
71
72
73
74
4-225-522-01
4-225-523-01
1-773-056-11
1-773-032-11
A-4475-552-A
SPRING (DECK-A)
SPRING (DECK-B)
WIRE (FLAT TYPE) (17 CORE)
WIRE (FLAT TYPE) (15 CORE)
MIC BOARD, COMPLETE
LEVER (EJECT-C)
LEVER (EJECT-B)
SPRING (LEVER)
HOLDER (DECK-A) ASSY
75
76
77
78
1-680-171-11
1-680-172-11
1-680-181-11
1-680-180-11
TC-A BOARD
TC-B BOARD
HEADPHONES BOARD
FRONT INPUT BOARD
Part No.
Description
51
52
53
54
55
4-232-080-01
X-4953-376-1
4-232-085-01
4-232-070-01
4-232-069-01
COVER (TC)
LID (TC) ASSY
SPRING (TC-LID)
KNOB (TC-B)
KNOB (TC-A)
56
57
58
59
60
4-226-537-01
4-232-067-01
4-951-620-01
4-226-883-01
4-226-880-01
61
62
63
64
4-226-882-01
4-226-881-01
4-226-889-01
X-4952-464-1
56
Remark
Ref. No.
Remark
HCD-XG80/XG700
8-3. FRONT PANEL SECTION-2
101
108
101
112
101
not supplied
not supplied
(PANEL VR
board)
109
115
not supplied
(ILLUMINATION board)
not supplied
107
111
110
not
supplied
101
supplied with S736
115
106
104
105
101
not supplied
103
113
102
101
118
115
117
101
116
Part No.
Description
Part No.
Description
101
102
103
104
105
4-951-620-01
4-224-104-11
X-4953-374-1
4-040-472-01
4-232-068-01
SCREW (2.6X8), +BVTP
DAMPER
PANEL (CD) ASSY, SUB
LATCH, D.C.
KNOB (CD)
111
112
113
113
114
4-232-078-01
1-773-150-11
X-4953-379-1
X-4953-380-1
4-232-066-01
HOLDER (LED)
WIRE (FLAT TYPE) (21 CORE)
PANEL ASSY, FRONT (XG700)
PANEL ASSY, FRONT (XG80)
KNOB (VOL)
106
107
108
109
110
X-4953-377-1
4-232-086-01
A-4475-589-A
1-751-688-11
4-232-072-01
LID (CD) ASSY
SPRING (CD)
PANEL FL BOARD, COMPLETE
WIRE (FLAT TYPE) (13 CORE)
INDICATOR (ILLUMI)
115
116
117
118
4-951-620-11
1-680-183-11
1-680-178-11
1-680-177-11
SCREW (2.6X10), +BVTP
CD-R (2) BOARD
CD-R (1) BOARD
CD-L BOARD
Ref. No.
Remark
Ref. No.
114
Remark
57
HCD-XG80/XG700
8-4. CHASSIS SECTION
#2
#5
not supplied
160
#5
#3
159
#2
153
not supplied
#3
T951
152
154
155
not supplied
#4
#3
158
not supplied
156
not supplied
#3
#3
not supplied
#3
#3
CDM37M-5BD32L
151
not
supplied
157
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
Ref. No.
Part No.
Description
151
152
152
152
0 153
1-790-287-11
A-4475-583-A
A-4475-591-A
A-4476-049-A
1-575-653-11
WIRE (FLAT TYPE) (19 CORE)
PA BOARD, COMPLETE (E2, MX, AR)
PA BOARD, COMPLETE (AEP, UK)
PA BOARD, COMPLETE (EA, SP)
CORD, POWER (MX)
0 153
0 153
0 153
0 153
154
1-777-071-51
1-777-071-81
1-783-941-12
1-791-901-11
3-703-244-00
CORD, POWER (AEP, UK)
CORD, POWER (EA, SP)
CORD, POWER (AR)
CORD, POWER (E2)
BUSHING (FBS001), CORD (XG700)
154
* 155
4-966-266-01 BUSHING (S) (FBS002), CORD (XG80)
4-988-533-01 HOLDER, PWB
58
#3
not supplied
Remark
Ref. No.
Part No.
Description
156
156
156
156
156
A-4475-586-A
A-4475-594-A
A-4476-051-A
A-4476-053-A
A-4476-074-A
MAIN BOARD, COMPLETE (E2, AR)
MAIN BOARD, COMPLETE (AEP, UK)
MAIN BOARD, COMPLETE (SP)
MAIN BOARD, COMPLETE (MX)
MAIN BOARD, COMPLETE (EA)
157
158
159
160
0 T951
X-494-122-81
4-235-701-01
1-680-174-11
1-680-175-11
1-435-246-11
FOOT (F22125H-M)
COVER DUST
TRANS BOARD
SUB TRANS BOARD
TRANSFORMER, POWER (XG80)
0 T951
1-435-799-11 TRANSFORMER, POWER (XG700)
Remark
HCD-XG80/XG700
8-5. TAPE MECHANISM DECK SECTION-1
(TCM-230PWR42)
408
408
Tape mechanism deck section-2
407
404
406
HP101
403
407
405
HRPE101
403
406
404
405
409
402
402
401
Ref. No.
Part No.
Description
401
402
403
404
405
3-376-464-11
3-911-116-42
3-016-574-01
X-3374-156-5
X-3374-155-5
SCREW (+PTT 2.6X6), GROUND POINT
RIVET, PUSH
SPRING (HEAD), TENSION
PINCH LEVER (REV) ASSY
PINCH LEVER (FWD) ASSY
Remark
406
3-017-365-01 BASE (PINCH LEVER FWD)
Ref. No.
Part No.
407
3-017-366-01
408
3-016-567-02
409
A-2007-849-A
HP101 A-2004-778-A
HRPE101A-2004-779-A
Description
Remark
BASE (PINCH LEVER REV)
SPRING (CASSETTE), LEAF
AUDIO BOARD, COMPLETE
BASE (A) ASSY, HEAD
BASE (B) ASSY, HEAD
59
HCD-XG80/XG700
8-6. TAPE MECHANISM DECK SECTION-2
(TCM-230PWR42)
465
451
461
459
463
462
466
#12
460
455
452
469
458
#11
#13
#12
470
458
460
456
#12
454
464
470
M1
452
467
457
468
453
Part No.
Description
Part No.
Description
451
452
453
454
455
X-4952-881-1
3-041-946-01
4-227-239-01
X-3378-247-1
X-3378-249-1
CHASSIS ASSY, MAIN
BELT (CAPSTAN B)
BELT (CAPSTAN C)
FLYWHEEL (A-FWD) ASSY
FLYWHEEL (B-FWD) ASSY
462
463
464
465
466
4-228-450-01
3-019-208-01
A-2004-795-A
1-454-887-21
A-2004-796-A
SPRING (REVERSE SLIDER), TORSION
WASHER, STOPPER
CHASSIS (A) ASSY, SUB
SOLENOID, PLUNGER
CHASSIS (B) ASSY, SUB
456
457
458
459
460
X-3378-250-1
X-3378-248-1
3-041-947-01
3-703-454-21
3-016-566-01
FLYWHEEL (B-REV) ASSY
FLYWHEEL (A-REV) ASSY
BELT (FR)
SCREW (1.7X6), TAPPING
SLIDER, REVERSE
467
468
469
470
M1
3-040-580-11
3-017-407-01
3-359-464-41
3-359-464-11
X-3378-246-1
PULLEY (TENSION)
WASHER (FR LEVER), STOPPER
WASHER (CAPSTAN)
WASHER (CAPSTAN)
MOTOR ASSY (CAPSTAN) (TAPE)
461
A-2007-852-A LEAF SW BOARD, COMPLETE
Ref. No.
60
Remark
Ref. No.
Remark
HCD-XG80/XG700
8-7. CD MECHANISM DECK SECTION
(CDM37M-5BD32L)
501
508
501
505
504
507
#3
511
not
supplied
506
510
501
509
502
510
523
510
503
525
512
522
524
518
518
502
M201
517
519
515
513
#3
516
#3
519
#3
not
supplied
511
520
#3
514
521
#3
Part No.
Description
Ref. No.
Part No.
Description
501
502
503
504
505
4-987-976-01
4-944-490-01
A-4660-978-A
4-978-421-01
4-978-425-01
SCREW, STEP
BELT (TIMING)
GEAR (PULLEY) ASSY
GEAR (MID)
ROLLER (CAM)
* 514
515
* 516
* 517
518
A-4673-765-A
4-978-426-01
1-659-059-13
1-659-058-13
4-985-672-01
CD MOTOR BOARD, COMPLETE
INDICATOR (NO.)
LED BOARD
TABLE SENSOR BOARD
SCREW (+PTPWHM2.6), FLOATING
506
507
508
509
510
4-978-420-01
1-452-925-21
4-978-417-01
4-993-142-03
X-4947-960-1
CAM (HOLDER)
MAGNET ASSY
TABLE, DISC
PULLEY (L), PRESS
ROLLER ASSY
519
* 520
521
522
523
4-958-593-01
4-978-419-01
4-998-716-01
4-989-493-01
4-989-494-01
SPRING (BU), COMPRESSION
HOLDER (BU-5)
SCREW, BU FITTING
SLIDER (37)
SCREW (SLIDER), STEP
Ref. No.
* 511
512
* 513
4-978-583-01 BRACKET (BU)
4-978-418-01 CHASSIS
4-980-385-01 HOLDER (SW)
Remark
524
525
M201
Remark
4-989-819-21 SPRING, TENSION
4-989-491-01 COVER, LENS
A-4660-977-A MOTOR ASSY (TABLE) (CD)
61
HCD-XG80/XG700
8-8. BASE UNIT SECTION
(BU-5BD32L)
601
602
609
603
605
604
M101
M102
604
606
607
608
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
Ref. No.
Part No.
Description
0 601
602
603
604
605
8-820-020-02
1-782-817-11
4-917-567-21
4-951-940-01
4-917-565-01
OPTICAL PICK-UP KSS-213D/Q-RP
WIRE (FLAT TYPE) (16 CORE)
GEAR (M)
INSULATOR (BU)
SHAFT, SLED
606
62
4-917-564-01 GEAR (P), FLATNESS
Remark
Ref. No.
607
608
609
M101
M102
Part No.
Description
A-4724-486-A
4-951-620-01
3-713-786-51
X-4917-523-3
X-4917-504-1
BD BOARD, COMPLETE
SCREW (2.6X8), +BVTP
SCREW +P 2X3
MOTOR ASSY (SPINDLE) (CD)
MOTOR ASSY (SLED) (CD)
Remark
HCD-XG80/XG700
SECTION 9
ELECTRICAL PARTS LIST
AUDIO
NOTE:
• Items marked “*” are not stocked since they
• Due to standardization, replacements in the
are seldom required for routine service.
parts list may be different from the parts speciSome delay should be anticipated when orderfied in the diagrams or the components used
ing these items.
on the set.
• SEMICONDUCTORS
• -XX and -X mean standardized parts, so they
In each case, u: µ, for example:
may have some difference from the original
uA. . : µA. .
uPA. . : µPA. .
one.
uPB. . : µPB. .
uPC. . : µPC. .
• RESISTORS
uPD. . : µPD. .
All resistors are in ohms.
• CAPACITORS
METAL: Metal-film resistor.
uF: µF
METAL OXIDE: Metal oxide-film resistor.
• COILS
F: nonflammable
uH: µH
• Abbreviation
AR : Argentina model
MX : Mexican model
E2 : 120 V AC area in E model SP : Singapore model
EA : Saudi Arabia model
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
A-2007-849-A AUDIO BOARD, COMPLETE
**********************
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
Description
Remark
< IC >
< CAPACITOR >
C301
C302
C303
C304
C305
1-162-289-31
1-126-968-11
1-162-282-31
1-130-483-00
1-128-551-11
CERAMIC
ELECT
CERAMIC
MYLAR
ELECT
390PF
100uF
100PF
0.01uF
22uF
10%
20%
10%
5%
20%
50V
6.3V
50V
50V
25V
C311
C313
C314
C315
C331
1-162-289-31
1-162-282-31
1-130-487-00
1-126-233-11
1-137-427-11
CERAMIC
CERAMIC
MYLAR
ELECT
MYLAR
390PF
100PF
0.022uF
22uF
120PF
10%
10%
5%
20%
5%
50V
50V
50V
50V
50V
C332
C333
C401
C402
C403
1-162-288-31
1-162-209-31
1-162-289-31
1-126-968-11
1-162-282-31
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
330PF
27PF
390PF
100uF
100PF
10%
5%
10%
20%
10%
50V
50V
50V
6.3V
50V
C404
C405
C411
C413
C414
1-130-483-00
1-128-551-11
1-162-289-31
1-162-282-31
1-130-487-00
MYLAR
ELECT
CERAMIC
CERAMIC
MYLAR
0.01uF
22uF
390PF
100PF
0.022uF
5%
20%
10%
10%
5%
50V
25V
50V
50V
50V
C415
C431
C432
C433
C601
1-126-233-11
1-137-427-11
1-162-288-31
1-162-209-31
1-104-396-11
ELECT
MYLAR
CERAMIC
CERAMIC
ELECT
22uF
120PF
330PF
27PF
10uF
20%
5%
10%
5%
20%
50V
50V
50V
50V
16V
C602
C611
C612
C621
C622
1-104-396-11
1-104-396-11
1-104-396-11
1-137-150-11
1-126-961-11
ELECT
ELECT
ELECT
FILM
ELECT
10uF
10uF
10uF
0.01uF
2.2uF
20%
20%
20%
5%
20%
16V
16V
16V
100V
50V
C623
C624
C625
C627
C628
1-136-155-00
1-130-481-00
1-130-481-00
1-124-903-11
1-136-153-00
FILM
MYLAR
MYLAR
ELECT
FILM
0.015uF
0.0068uF
0.0068uF
1uF
0.01uF
5%
5%
5%
20%
5%
50V
50V
50V
50V
50V
C642
1-104-664-11 ELECT
47uF
20%
16V
IC601
IC602
IC611
8-759-111-44 IC uPC4570C-1
8-759-143-54 IC uPC1330HA
8-759-111-44 IC uPC4570C-1
< COIL >
L331
L431
1-410-780-11 INDUCTOR
1-410-780-11 INDUCTOR
27mH
27mH
< TRANSISTOR >
Q621
Q622
Q623
8-729-142-46 TRANSISTOR
8-729-142-46 TRANSISTOR
8-729-801-93 TRANSISTOR
2SC2001-LK
2SC2001-LK
2SD1387-3
< RESISTOR >
R301
R302
R303
R304
R305
1-247-881-00
1-249-409-11
1-249-433-11
1-247-889-00
1-247-858-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
220
22K
270K
13K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R311
R312
R314
R315
R331
1-247-881-00
1-247-807-31
1-247-882-11
1-247-850-11
1-249-430-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
100
130K
6.2K
12K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R401
R402
R403
R404
R405
1-247-881-00
1-249-409-11
1-249-433-11
1-247-889-00
1-247-858-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
220
22K
270K
13K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R411
R412
R414
R415
R431
1-247-881-00
1-247-807-31
1-247-882-11
1-247-850-11
1-249-430-11
CARBON
CARBON
CARBON
CARBON
CARBON
120K
100
130K
6.2K
12K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R481
R482
R491
R492
R601
1-249-416-11
1-249-419-11
1-249-416-11
1-249-419-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
820
1.5K
820
1.5K
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R602
R608
1-249-409-11 CARBON
1-249-409-11 CARBON
220
220
5%
5%
1/4W
1/4W
< CONNECTOR >
CN601
1-695-338-11 PIN, CONNECTOR (PC BOARD) 15P
63
HCD-XG80/XG700
AUDIO
Ref. No.
R609
R611
R612
0 R621
0 R622
R623
R624
R625
BD
Part No.
Part No.
Description
C157
C159
C161
C162
C163
1-163-009-11
1-163-019-00
1-126-206-11
1-126-205-11
1-126-206-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
0.001uF
0.0068uF
100uF
47uF
100uF
10%
10%
20%
20%
20%
50V
50V
6.3V
6.3V
6.3V
C165
C167
C168
C171
C172
1-163-038-11
1-163-235-11
1-163-235-11
1-163-009-11
1-163-123-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22PF
22PF
0.001uF
180PF
5%
5%
10%
5%
25V
50V
50V
50V
50V
RES, ADJ, CARBON 2.2K
RES, ADJ, CARBON 2.2K
RES, ADJ, CARBON 220K
RES, ADJ, CARBON 220K
C181
C182
1-163-009-11 CERAMIC CHIP
1-163-123-00 CERAMIC CHIP
0.001uF
180PF
10%
5%
50V
50V
< TRANSFORMER >
CN101
CN102
Description
Remark
1-249-433-11 CARBON
1-249-409-11 CARBON
1-249-409-11 CARBON
22K
220
220
5%
5%
5%
1/4W
1/4W
1/4W
1-212-851-00
1-212-851-00
1-249-432-11
1-249-432-11
1-249-429-11
5.6
5.6
18K
18K
10K
5%
5%
5%
5%
5%
1/4W F
1/4W F
1/4W
1/4W
1/4W
FUSIBLE
FUSIBLE
CARBON
CARBON
CARBON
< VARIABLE RESISTOR >
RV301
RV311
RV341
RV441
1-238-598-11
1-238-598-11
1-241-768-11
1-241-768-11
Ref. No.
< CONNECTOR >
1-778-874-11 CONNECTOR, FFC (LIF (NON-ZIF)) 19P
1-777-937-11 CONNECTOR, FFC/FPC 16P
T621
1-423-980-11 TRANSFORMER, BIAS OSCILLATION
**************************************************************
A-4724-486-A BD BOARD, COMPLETE
*******************
< FERRITE BEAD >
FB101
FB103
1-500-445-21 FERRITE
1-500-445-21 FERRITE
< CAPACITOR >
0uH
0uH
< IC >
C101
C102
C103
C104
C108
1-163-005-11
1-164-004-11
1-163-005-11
1-163-009-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
0.1uF
470PF
0.001uF
0.1uF
10%
10%
10%
10%
10%
50V
25V
50V
50V
25V
IC101
IC102
IC103
C109
C110
C111
C112
C113
1-163-011-11
1-164-182-11
1-163-251-11
1-163-038-11
1-163-038-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0015uF 10%
0.0033uF 10%
100PF
5%
0.1uF
0.1uF
50V
50V
50V
25V
25V
Q101
C114
C115
C116
C117
C118
1-163-038-11
1-126-607-11
1-126-607-11
1-126-209-11
1-163-009-11
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
47uF
47uF
100uF
0.001uF
25V
4V
4V
4V
50V
C119
C121
C122
C123
C124
1-163-235-11
1-163-038-11
1-126-206-11
1-163-021-11
1-107-823-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
0.1uF
100uF
0.01uF
0.47uF
C125
C126
C127
C128
C129
1-163-038-11
1-163-038-11
1-128-065-11
1-163-038-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
68uF
0.1uF
0.01uF
C130
C131
C133
C140
C141
1-164-346-11
1-124-779-00
1-125-838-11
1-164-346-11
1-164-346-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
10uF
2.2uF
1uF
1uF
C143
C151
C153
C154
C156
1-163-038-11
1-163-235-11
1-163-038-11
1-110-501-11
1-163-235-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22PF
0.1uF
0.33uF
22PF
64
Remark
20%
20%
20%
10%
5%
20%
10%
10%
20%
20%
10%
5%
10%
5%
50V
25V
6.3V
50V
16V
25V
25V
10V
25V
50V
16V
16V
6.3V
16V
16V
25V
50V
25V
16V
50V
8-752-386-85 IC CXD2587Q
8-759-549-28 IC BA5974FP-E2
8-752-085-51 IC CXA2568M-T6
< TRANSISTOR >
8-729-010-08 TRANSISTOR
MSB710-R
< RESISTOR >
R101
R102
R103
R104
R105
1-216-077-00
1-216-097-11
1-216-077-00
1-216-085-00
1-216-073-00
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
15K
100K
15K
33K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R106
R107
R108
R109
R110
1-216-049-11
1-216-073-00
1-216-061-00
1-216-121-11
1-216-025-11
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
1K
10K
3.3K
1M
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R111
R113
R114
R116
R117
1-216-121-11
1-216-121-11
1-216-073-00
1-216-001-00
1-216-049-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
1M
1M
10K
10
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R119
R123
R124
R131
R143
1-216-041-00
1-216-073-00
1-216-097-11
1-216-033-00
1-216-103-00
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
470
10K
100K
220
180K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R144
R147
R148
R149
R158
1-216-103-00
1-216-069-00
1-216-001-00
1-216-001-00
1-216-111-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
180K
6.8K
10
10
390K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R159
R161
1-216-101-00 METAL CHIP
1-216-308-00 METAL CHIP
150K
4.7
5%
5%
1/10W
1/10W
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
HCD-XG80/XG700
BD
Ref. No.
Part No.
Description
Remark
R162
R171
R172
1-216-101-00 METAL CHIP
1-216-078-00 RES-CHIP
1-216-073-00 METAL CHIP
150K
16K
10K
5%
5%
5%
1/10W
1/10W
1/10W
R173
R181
R182
R183
1-216-077-00
1-216-078-00
1-216-073-00
1-216-077-00
15K
16K
10K
15K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
< NETWORK RESISTOR >
RN101
RN102
1-233-576-11 RES, CHIP NETWORK 100
1-233-576-11 RES, CHIP NETWORK 100
< SWITCH >
S101
1-572-085-11 SWITCH, LEAF (LIMIT)
Ref. No.
CD MOTOR
Part No.
*
A-4673-765-A CD MOTOR BOARD, COMPLETE
**************************
*
4-980-385-01 HOLDER (SW)
D741
Remark
8-719-058-04 LED SEL5223S-TP15 (NON-STOP)
< RESISTOR >
R741
R742
R743
R744
R745
1-249-407-11
1-249-438-11
1-249-420-11
1-249-422-11
1-247-843-11
CARBON
CARBON
CARBON
CARBON
CARBON
150
56K
1.8K
2.7K
3.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R746
R747
R748
R749
R750
1-249-425-11
1-249-427-11
1-249-429-11
1-249-431-11
1-249-434-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7K
6.8K
10K
15K
27K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
10uF
0.1uF
10uF
20%
20%
S741
S742
S743
S744
S745
< CAPACITOR >
50V
50V
50V
1-762-875-21 SWITCH, KEYBOARD (LOOP)
1-762-587-11 SWITCH, PUSH (1 KEY)
(LID (CD) OPEN/CLOSE)
1-762-875-21 SWITCH, KEYBOARD (FLASH)
1-762-875-21 SWITCH, KEYBOARD (EDIT)
1-762-875-21 SWITCH, KEYBOARD (NON-STOP)
S746
1-762-875-21 SWITCH, KEYBOARD (DISC 1)
S747
1-762-875-21 SWITCH, KEYBOARD (DISC 2)
S748
1-762-875-21 SWITCH, KEYBOARD (DISC 3)
S749
1-762-875-21 SWITCH, KEYBOARD (DISC 4)
S750
1-762-875-21 SWITCH, KEYBOARD (DISC 5)
**************************************************************
< CONNECTOR >
* CN201
Description
< SWITCH >
X101
1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)
**************************************************************
1-126-964-11 ELECT
1-164-159-21 CERAMIC
1-126-964-11 ELECT
CD-R (1)
< LED >
< VIBRATOR >
C201
C202
C203
CD-L
1-680-178-11 CD-R (1) BOARD
**************
1-568-947-11 PIN, CONNECTOR 9P
< CONNECTOR >
< IC >
CN703
IC201
1-785-333-11 PIN, CONNECTOR (LIGHT ANGLE) 7P
8-759-365-94 IC TA8409S
< LED >
< COIL >
D700
L201
1-408-117-00 INDUCTOR
8-719-056-13 LED SML79423C-TP15 (HX)
10uH
< RESISTOR >
< RESISTOR >
R205
R206
1-249-427-11 CARBON
1-249-425-11 CARBON
6.8K
4.7K
5%
5%
1/4W
1/4W
< SWITCH >
S201
1-762-587-11 SWITCH, PUSH (1 KEY) (UP)
**************************************************************
1-680-177-11 CD-L BOARD
***********
R751
R752
R753
R754
R755
1-249-415-11
1-249-417-11
1-249-418-11
1-249-420-11
1-249-422-11
CARBON
CARBON
CARBON
CARBON
CARBON
680
1K
1.2K
1.8K
2.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R756
R757
R758
R759
1-247-843-11
1-249-425-11
1-249-403-11
1-249-403-11
CARBON
CARBON
CARBON
CARBON
3.3K
4.7K
68
68
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
< SWITCH >
< CAPACITOR >
C741
1-162-306-11 CERAMIC
0.01uF
30%
< CONNECTOR >
CN704
16V
S751
S752
S753
S754
S755
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (HX)
SWITCH, KEYBOARD (x)
SWITCH, KEYBOARD (m)
SWITCH, KEYBOARD (M)
SWITCH, KEYBOARD (DISC SKIP)
1-785-332-11 PIN, CONNECTOR (LIGHT ANGLE) 6P
S756
1-762-875-21 SWITCH, KEYBOARD (REPEAT)
S757
1-762-875-21 SWITCH, KEYBOARD (PLAY MODE)
**************************************************************
65
HCD-XG80/XG700
CD-R (2)
Ref. No.
FRONT INPUT
Part No.
HEADPHONES
Description
Remark
Ref. No.
ILLUMINATION
Part No.
LEAF SW
Description
Remark
ILLUMINATION BOARD
*******************
1-680-183-11 CD-R (2) BOARD
**************
< CAPACITOR >
< CAPACITOR >
C751
C752
1-162-306-11 CERAMIC
1-162-306-11 CERAMIC
0.01uF
0.01uF
30%
30%
16V
16V
C791
C792
C793
1-162-974-11 CERAMIC CHIP
1-162-974-11 CERAMIC CHIP
1-162-974-11 CERAMIC CHIP
< ROTARY ENCODER >
0.01uF
0.01uF
0.01uF
50V
50V
50V
< CONNECTOR >
S763
1-473-393-11 ENCODER, ROTARY (JOG DIAL)
**************************************************************
CN791
1-770-011-41 CONNECTOR, BOARD TO BOARD 4P
< LED >
1-680-180-11 FRONT INPUT BOARD
******************
D791
8-719-075-87 LED SECU3M02C (ILLUMINATION)
**************************************************************
< CAPACITOR >
C801
C802
C803
C811
C812
1-162-294-31
1-162-294-31
1-126-960-11
1-162-282-31
1-164-159-21
CERAMIC
CERAMIC
ELECT
CERAMIC
CERAMIC
0.001uF
0.001uF
1uF
100PF
0.1uF
10%
10%
20%
10%
50V
50V
50V
50V
50V
A-2007-852-A LEAF SW BOARD, COMPLETE
************************
< CAPACITOR >
C1001
1-107-716-11 ELECT
10V
CN1001 1-784-459-11 CONNECTOR, FFC/FPC 17P
1-424-228-11 FILTER, NOISE
< DIODE >
< JACK >
J804
20%
< CONNECTOR >
< NOISE FILTER >
FL803
33uF
1-815-310-11 JACK 3P (GAME INPUT AUDIO/VIDEO)
D1001
D1002
8-719-991-33 DIODE 1SS133T-77
8-719-991-33 DIODE 1SS133T-77
< RESISTOR >
< PHOTO INTERRUPTER >
R801
1-249-417-11 CARBON
1K
5%
1/4W
R802
1-249-437-11 CARBON
47K
5%
1/4W
R803
1-249-417-11 CARBON
1K
5%
1/4W
R804
1-249-437-11 CARBON
47K
5%
1/4W
R805
1-247-804-11 CARBON
75
5%
1/4W
**************************************************************
IC1001
IC1002
8-749-014-38 PHOTO INTERRUPTER SG-264
8-749-014-38 PHOTO INTERRUPTER SG-264
< TRANSISTOR >
Q1001
8-729-029-56 TRANSISTOR
1-680-181-11 HEADPHONES BOARD
******************
< RESISTOR >
< CAPACITOR >
C891
C892
C893
1-162-294-31 CERAMIC
1-162-294-31 CERAMIC
1-164-159-21 CERAMIC
0.001uF
0.001uF
0.1uF
10%
10%
50V
50V
50V
< CONNECTOR >
CN802
DTA144ESA
1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4P
R907
R1001
R1002
R1003
R1004
1-249-441-11
1-249-409-11
1-249-409-11
1-249-414-11
1-247-834-11
CARBON
CARBON
CARBON
CARBON
CARBON
100K
220
220
560
1.3K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R1005
R1006
R1007
R1008
1-247-818-11
1-247-864-11
1-247-852-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
300
24K
7.5K
1K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
< JACK >
< VARIABLE RESISTOR >
J803
1-770-226-11 JACK (LARGE TYPE) (PHONES)
< RESISTOR >
RV1001 1-241-785-11 RES, ADJ, CARBON 10K
RV1002 1-241-785-11 RES, ADJ, CARBON 10K
R810
1-247-807-31 CARBON
100
5%
1/4W
**************************************************************
< SWITCH >
S1001
S1002
S1003
S1004
S1005
66
1-570-953-11
1-570-953-11
1-771-333-11
1-771-205-11
1-771-205-11
SWITCH, PUSH (1 KEY) (DECK A PLAY)
SWITCH, PUSH (1 KEY) (DECK B PLAY)
SWITCH, LEAF (DECK A HALF)
SWITCH, LEAF (DECK A 120/70)
SWITCH, LEAF (DECK A REC)
HCD-XG80/XG700
LEAF SW
Ref. No.
Part No.
Description
Remark
S1006 1-771-333-11 SWITCH, LEAF (DECK B HALF)
S1008 1-771-205-11 SWITCH, LEAF (DECK B 120/70)
S1009 1-771-205-11 SWITCH, LEAF (DECK B REC)
**************************************************************
1-659-059-13 LED BOARD
**********
*
Ref. No.
Part No.
LED
Description
MAIN
Remark
C171
C172
1-126-964-11 ELECT
1-164-363-11 CERAMIC CHIP
10uF
560PF
20%
5%
50V
50V
C173
C174
C175
C176
C177
1-136-169-00
1-136-169-00
1-126-964-11
1-130-493-00
1-130-483-00
FILM
FILM
ELECT
MYLAR
MYLAR
0.22uF
0.22uF
10uF
0.068uF
0.01uF
5%
5%
20%
5%
5%
50V
50V
50V
50V
50V
C181
C182
C183
C191
C192
1-164-156-11
1-164-156-11
1-164-156-11
1-162-974-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.01uF
0.1uF
C193
C301
C302
C303
C304
1-126-964-11
1-126-960-11
1-130-479-00
1-136-165-00
1-136-165-00
ELECT
ELECT
MYLAR
FILM
FILM
10uF
1uF
0.0047uF
0.1uF
0.1uF
20%
20%
5%
5%
5%
50V
50V
50V
50V
50V
C305
C306
C307
C308
C309
1-126-964-11
1-126-960-11
1-126-959-11
1-126-964-11
1-137-194-81
ELECT
ELECT
ELECT
ELECT
FILM
10uF
1uF
0.47uF
10uF
0.47uF
20%
20%
20%
20%
5%
50V
50V
50V
50V
50V
C310
C311
C312
C313
C314
1-162-962-11
1-126-964-11
1-126-959-11
1-162-964-11
1-126-964-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
470PF
10uF
0.47uF
0.001uF
10uF
10%
20%
20%
10%
20%
50V
50V
50V
50V
50V
C315
C316
C317
C320
C333
1-126-963-11
1-104-664-11
1-104-664-11
1-162-962-11
1-162-968-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
4.7uF
47uF
47uF
470PF
0.0047uF
20%
20%
20%
10%
10%
50V
16V
16V
50V
50V
C334
C351
C352
C353
C354
1-162-968-11
1-126-960-11
1-130-479-00
1-136-165-00
1-136-165-00
CERAMIC CHIP
ELECT
MYLAR
FILM
FILM
0.0047uF
1uF
0.0047uF
0.1uF
0.1uF
10%
20%
5%
5%
5%
50V
50V
50V
50V
50V
C355
C356
C357
C358
C359
1-126-964-11
1-126-960-11
1-126-959-11
1-126-964-11
1-137-194-81
ELECT
ELECT
ELECT
ELECT
FILM
10uF
1uF
0.47uF
10uF
0.47uF
20%
20%
20%
20%
5%
50V
50V
50V
50V
50V
C401
C411
C412
C413
C414
1-126-961-11
1-164-156-11
1-164-156-11
1-126-916-11
1-126-916-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
2.2uF
0.1uF
0.1uF
1000uF
1000uF
20%
50V
25V
25V
6.3V
6.3V
C416
C431
C451
C510
C511
1-126-935-11
1-164-156-11
1-126-961-11
1-162-918-11
1-162-919-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
470uF
0.1uF
2.2uF
18PF
22PF
20%
C516
C562
C564
C598
C599
1-164-156-11
1-164-156-11
1-104-664-11
1-163-038-11
1-104-664-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0.1uF
0.1uF
47uF
0.1uF
47uF
< LED >
D201
8-719-032-98 LED SEL5820A (DISC No.)
< TRANSISTOR >
Q201
8-729-119-78 TRANSISTOR
2SC2785-HFE
< RESISTOR >
R201
1-249-433-11 CARBON
22K
5%
1/4W
R202
1-249-411-11 CARBON
330
5%
1/4W
R203
1-249-437-11 CARBON
47K
5%
1/4W
**************************************************************
A-4475-586-A
A-4475-594-A
A-4476-051-A
A-4476-053-A
A-4476-074-A
25V
25V
25V
50V
25V
MAIN BOARD, COMPLETE (E2, AR)
MAIN BOARD, COMPLETE (AEP, UK)
MAIN BOARD, COMPLETE (SP)
MAIN BOARD, COMPLETE (MX)
MAIN BOARD, COMPLETE (EA)
*********************
4-875-327-31 HEAT SINK
4-948-236-21 CUSHION (107)
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
< CAPACITOR >
C111
C112
C113
C114
C115
1-137-195-11
1-130-488-00
1-136-167-00
1-130-480-00
1-130-489-00
FILM
MYLAR
FILM
MYLAR
MYLAR
0.56uF
0.027uF
0.15uF
0.0056uF
0.033uF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C116
C117
C118
C119
C120
1-130-473-00
1-130-483-00
1-162-959-11
1-130-477-00
1-130-477-00
MYLAR
MYLAR
CERAMIC CHIP
MYLAR
MYLAR
0.0015uF
0.01uF
330PF
0.0033uF
0.0033uF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C121
C122
C123
C124
C125
1-126-964-11
1-164-363-11
1-136-169-00
1-136-169-00
1-126-964-11
ELECT
CERAMIC CHIP
FILM
FILM
ELECT
10uF
560PF
0.22uF
0.22uF
10uF
20%
5%
5%
5%
20%
50V
50V
50V
50V
50V
C131
C132
C135
C161
C162
1-104-664-11
1-104-664-11
1-126-964-11
1-137-195-11
1-130-488-00
ELECT
ELECT
ELECT
FILM
MYLAR
47uF
47uF
10uF
0.56uF
0.027uF
20%
20%
20%
5%
5%
16V
16V
50V
50V
50V
C163
C164
C165
C166
C167
1-136-167-00
1-130-480-00
1-130-489-00
1-130-473-00
1-130-483-00
FILM
MYLAR
MYLAR
MYLAR
MYLAR
0.15uF
0.0056uF
0.033uF
0.0015uF
0.01uF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C168
C169
C170
1-162-959-11 CERAMIC CHIP
1-130-477-00 MYLAR
1-130-477-00 MYLAR
330PF
5%
0.0033uF 5%
0.0033uF 5%
50V
50V
50V
20%
20%
20%
5%
5%
20%
20%
10V
25V
50V
50V
50V
25V
25V
16V
25V
16V
67
HCD-XG80/XG700
MAIN
Ref. No.
Part No.
Description
C601
C602
C603
C604
1-162-959-11
1-162-927-11
1-162-927-11
1-126-961-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
C604
Remark
330PF
100PF
100PF
2.2uF
5%
5%
5%
20%
1-126-963-11 ELECT
4.7uF
20%
C605
C606
C607
1-130-479-00 MYLAR
1-130-473-00 MYLAR
1-136-159-00 FILM
0.0047uF 5%
0.0015uF 5%
0.033uF 5%
C607
1-136-165-00 FILM
0.1uF
C608
1-162-974-11 CERAMIC CHIP
0.01uF
C609
C651
C652
C653
C654
1-126-933-11
1-162-959-11
1-162-927-11
1-162-927-11
1-126-961-11
100uF
330PF
100PF
100PF
2.2uF
20%
5%
5%
5%
20%
16V
50V
50V
50V
50V
(XG80)
C654
1-126-963-11 ELECT
4.7uF
20%
C655
C656
C657
1-130-479-00 MYLAR
1-130-473-00 MYLAR
1-136-159-00 FILM
0.0047uF 5%
0.0015uF 5%
0.033uF 5%
C657
1-136-165-00 FILM
0.1uF
50V
(XG700)
50V
50V
50V
(XG80)
50V
(XG700)
C658
C659
C699
C701
C702
1-162-974-11
1-126-933-11
1-162-974-11
1-162-960-11
1-162-960-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
100uF
0.01uF
220PF
220PF
C703
C704
1-162-960-11 CERAMIC CHIP
1-162-960-11 CERAMIC CHIP
220PF
220PF
C705
1-162-960-11 CERAMIC CHIP
220PF
C721
C722
1-126-960-11 ELECT
1-126-926-11 ELECT
1uF
1000uF
C724
C751
C752
C753
C772
1-162-962-11
1-162-960-11
1-162-960-11
1-162-960-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
220PF
220PF
220PF
0.1uF
C774
C777
C782
C803
C804
1-164-156-11
1-164-156-11
1-104-664-11
1-126-964-11
1-136-165-00
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
FILM
0.1uF
0.1uF
47uF
10uF
0.1uF
20%
20%
5%
25V
25V
16V
50V
50V
C805
C806
C808
C902
C903
1-136-165-00
1-126-916-11
1-109-953-11
1-126-937-11
1-126-964-11
FILM
ELECT
ELECT
ELECT
ELECT
0.1uF
1000uF
2.2uF
4700uF
10uF
5%
20%
20%
20%
20%
50V
6.3V
50V
16V
50V
C904
C905
C911
C912
C913
1-126-964-11
1-126-935-11
1-126-964-11
1-126-916-11
1-104-664-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
470uF
10uF
1000uF
47uF
20%
20%
20%
20%
20%
50V
10V
50V
6.3V
16V
68
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
5%
5%
20%
10%
10%
50V
50V
50V
50V
(XG80)
50V
(XG700)
50V
50V
50V
(XG80)
50V
(XG700)
50V
50V
16V
50V
50V
50V
10%
50V
10%
50V
(AEP, UK, MX)
10%
50V
(AEP, UK, MX)
20%
50V
20%
10V
10%
10%
10%
10%
50V
50V
50V
50V
25V
Ref. No.
Part No.
Description
Remark
C914
C932
C933
C934
C935
1-126-916-11
1-126-964-11
1-126-933-11
1-126-964-11
1-126-767-11
ELECT
ELECT
ELECT
ELECT
ELECT
1000uF
10uF
100uF
10uF
1000uF
20%
20%
20%
20%
20%
6.3V
50V
16V
50V
16V
C936
C937
C938
C952
C953
1-126-964-11
1-126-933-11
1-126-933-11
1-126-943-11
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
100uF
100uF
2200uF
10uF
20%
20%
20%
20%
20%
50V
16V
16V
25V
50V
C954
C955
C961
1-126-964-11 ELECT
1-126-935-11 ELECT
1-164-156-11 CERAMIC CHIP
10uF
470uF
0.1uF
20%
20%
50V
10V
25V
< CONNECTOR >
CN303
CN304
CN411
CN412
CN431
1-784-776-11
1-784-778-11
1-784-780-11
1-785-321-11
1-784-774-11
CONNECTOR, FFC 15P
CONNECTOR, FFC 17P
CONNECTOR, FFC 19P
PIN, CONNECTOR (STRAIGHT) 9P
CONNECTOR, FFC 13P
CN441
CN441
CN452
CN702
CN901
1-563-616-11
1-750-747-11
1-785-316-11
1-691-767-11
1-778-982-21
CONNECTOR, FLEXIBLE 13P (XG80)
CONNECTOR, FFC/FPC 15P (XG700)
PIN, CONNECTOR (STRAIGHT) 4P
PLUG (MICRO CONNECTOR) 5P
CONNECTOR, BOARD TO BOARD 13P
CN902
CN903
1-778-982-21 CONNECTOR, BOARD TO BOARD 13P
1-564-506-11 PLUG, CONNECTOR 3P
< DIODE >
D191
D192
D193
D194
D501
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
D534
D801
D802
D803
D804
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
D805
D806
D807
D808
D911
8-719-988-61
8-719-988-61
8-719-988-61
8-719-210-33
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
1SS355TE-17
EC10DS2
1SS355TE-17
D912
D913
D931
D951
8-719-210-33
8-719-210-33
8-719-210-33
8-719-988-61
DIODE
DIODE
DIODE
DIODE
EC10DS2
EC10DS2
EC10DS2
1SS355TE-17
< FERRITE BEAD >
FB412
FB413
FB415
1-414-772-11 FERRITE
1-414-551-11 FERRITE
1-414-772-11 FERRITE
0uH
0uH
0uH
< FILTER >
FL501
FL502
1-233-289-21 FILTER, EMI (SMD)
1-233-289-21 FILTER, EMI (SMD)
HCD-XG80/XG700
MAIN
Ref. No.
FL503
Part No.
Description
Remark
1-233-289-21 FILTER, EMI (SMD)
< IC >
IC101
IC181
IC191
IC301
IC501
8-759-571-54
8-759-009-06
8-759-571-53
8-759-495-26
8-759-827-40
IC
IC
IC
IC
IC
M62493FP
MC14052BFEL
BA7615N
HA12215F
M30622MAA-A92FP
IC601
IC781
IC801
IC901
IC911
8-759-100-96
8-749-923-04
8-759-635-63
8-759-071-48
8-759-039-69
IC
IC
IC
IC
IC
NJM4558M-T1
TOTX178A (CD DIGITAL OUT OPTICAL)
M51943BSL-TP
TA7807S
uPC7805AHF
IC931
IC932
IC933
IC951
8-759-604-38
8-759-088-08
8-759-071-48
8-759-604-90
IC
IC
IC
IC
M5F78M10L
uPC7812AHF
TA7807S
M5F7907L
< JACK >
J701
J702
J705
1-794-148-21 JACK, PIN 8P
(PHONO IN, MD IN/OUT, VIDEO AUDIO IN)
1-815-043-11 JACK, PIN 2P (VIDEO VIDEO IN, VIDEO OUT)
1-573-028-31 JACK, PIN 4P (DJ MIX RETURN/SEND)
(AEP, UK, MX)
Ref. No.
Part No.
Description
Remark
Q332
8-729-029-86 TRANSISTOR
DTC124ESA
Q333
Q334
Q335
Q336
Q339
8-729-140-04
8-729-029-86
8-729-029-86
8-729-116-59
8-729-029-86
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SB1116A-L
DTC124ESA
DTC124ESA
2SB1068TP
DTC124ESA
Q801
Q802
Q803
Q804
Q901
8-729-620-05
8-729-029-40
8-729-029-40
8-729-029-40
8-729-040-20
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
DTA124ESA
DTA124ESA
DTA124ESA
RT1P137L-TP
Q902
Q903
Q904
Q905
Q906
8-729-029-40
8-729-040-19
8-729-029-86
8-729-119-76
8-729-620-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA124ESA
RT1N137L-TP
DTC124ESA
2SA1175-HFE
2SC2603-EF
Q911
Q912
Q913
Q914
Q931
8-729-040-20
8-729-029-86
8-729-040-20
8-729-029-86
8-729-040-20
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
RT1P137L-TP
DTC124ESA
RT1P137L-TP
DTC124ESA
RT1P137L-TP
Q932
Q961
Q962
8-729-029-86 TRANSISTOR
8-729-620-05 TRANSISTOR
8-729-140-04 TRANSISTOR
DTC124ESA
2SC2603-EF
2SB1116A-L
< SHORT >
< RESISTOR >
JR1
JR2
JR3
JR4
JR5
1-216-295-11
1-216-296-11
1-216-296-11
1-216-295-11
1-216-295-11
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR6
JR7
JR8
JR9
1-216-296-11
1-216-296-11
1-216-296-11
1-216-295-11
SHORT
SHORT
SHORT
SHORT
0
0
0
0
JR11
JR181
JR182
JR191
JR192
1-216-296-11
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR594
JR703
JR901
JR910
1-216-295-11
1-216-295-11
1-216-295-11
1-216-296-11
SHORT
SHORT
SHORT
SHORT
0
0
0
0
R111
R112
R113
1-216-833-11 METAL CHIP
1-216-857-11 METAL CHIP
1-216-848-11 METAL CHIP
10K
1M
180K
5%
5%
5%
R113
1-216-847-11 METAL CHIP
150K
5%
R114
1-216-818-11 METAL CHIP
560
5%
1/16W
1/16W
1/16W
(XG80)
1/16W
(XG700)
1/16W
R115
R116
R117
R118
R119
1-216-841-11
1-216-842-11
1-216-833-11
1-216-841-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
56K
10K
47K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R120
R121
R122
R123
1-216-845-11
1-216-833-11
1-216-295-11
1-216-847-11
METAL CHIP
METAL CHIP
SHORT
METAL CHIP
100K
10K
0
150K
5%
5%
1/16W
1/16W
5%
R123
1-216-850-11 METAL CHIP
270K
5%
1/16W
(XG700)
1/16W
(XG80)
R124
R125
R126
R127
1-216-825-11
1-216-827-11
1-216-825-11
1-216-847-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
3.3K
2.2K
150K
5%
5%
5%
5%
R127
1-216-852-11 METAL CHIP
390K
5%
R129
R131
R132
R133
R161
1-216-857-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
100
100
100
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R162
1-216-857-11 METAL CHIP
1M
5%
1/16W
< COIL >
L781
1-412-032-11 INDUCTOR CHIP 100uH
< TRANSISTOR >
Q111
Q112
Q113
Q115
Q161
8-729-620-05
8-729-620-05
8-729-141-30
8-729-029-86
8-729-620-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
2SC2603-EF
2SC3623A-LK
DTC124ESA
2SC2603-EF
Q162
Q163
Q165
Q331
8-729-620-05
8-729-141-30
8-729-029-86
8-729-140-04
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
2SC3623A-LK
DTC124ESA
2SB1116A-L
1/16W
1/16W
1/16W
1/16W
(XG700)
1/16W
(XG80)
69
HCD-XG80/XG700
MAIN
Ref. No.
Part No.
Description
Remark
R163
1-216-847-11 METAL CHIP
150K
5%
R163
1-216-848-11 METAL CHIP
180K
5%
R164
R165
1-216-818-11 METAL CHIP
1-216-841-11 METAL CHIP
560
47K
5%
5%
1/16W
(XG700)
1/16W
(XG80)
1/16W
1/16W
R166
R167
R168
R169
R170
1-216-842-11
1-216-833-11
1-216-841-11
1-216-825-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
56K
10K
47K
2.2K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R171
R172
R173
1-216-833-11 METAL CHIP
1-216-295-11 SHORT
1-216-847-11 METAL CHIP
10K
0
150K
5%
1/16W
5%
R173
1-216-850-11 METAL CHIP
270K
5%
R174
1-216-833-11 METAL CHIP
10K
5%
1/16W
(XG700)
1/16W
(XG80)
1/16W
R175
R177
1-216-845-11 METAL CHIP
1-216-847-11 METAL CHIP
100K
150K
5%
5%
R177
1-216-852-11 METAL CHIP
390K
5%
R178
R179
1-216-825-11 METAL CHIP
1-216-857-11 METAL CHIP
2.2K
1M
5%
5%
1/16W
1/16W
(XG700)
1/16W
(XG80)
1/16W
1/16W
R301
R302
R303
R304
R305
1-216-839-11
1-216-825-11
1-216-809-11
1-216-809-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
2.2K
100
100
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R306
R307
R308
R309
R311
1-216-832-11
1-216-832-11
1-216-829-11
1-216-837-11
1-216-857-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
8.2K
8.2K
4.7K
22K
1M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R312
R313
R315
R316
R317
1-218-900-11
1-216-845-11
1-216-833-11
1-216-836-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
160K
100K
10K
18K
10K
0.5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R318
R319
R321
R322
R332
1-216-833-11
1-216-852-11
1-216-826-11
1-216-832-11
1-216-819-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
390K
2.7K
8.2K
680
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R333
R334
R335
R340
R343
1-216-825-11
1-216-819-11
1-216-825-11
1-216-841-11
1-216-061-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
680
2.2K
47K
3.3K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/10W
R344
R345
R351
R352
R353
1-216-061-11
1-216-061-11
1-216-839-11
1-216-825-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
3.3K
33K
2.2K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/16W
1/16W
1/16W
R354
R355
R356
R357
1-216-809-11
1-216-825-11
1-216-832-11
1-216-832-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
2.2K
8.2K
8.2K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
70
Ref. No.
Part No.
Description
Remark
R358
1-216-829-11 METAL CHIP
4.7K
5%
1/16W
R359
R371
R372
R373
R374
1-216-839-11
1-216-841-11
1-216-829-11
1-216-821-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
47K
4.7K
1K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R375
R376
R377
R378
R401
1-218-892-11
1-216-829-11
1-216-841-11
1-218-892-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
75K
4.7K
47K
75K
100
0.5%
5%
5%
0.5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R402
R413
R414
R451
R452
1-216-827-11
1-216-295-11
1-216-295-11
1-216-809-11
1-216-827-11
METAL CHIP
SHORT
SHORT
METAL CHIP
METAL CHIP
3.3K
0
0
100
3.3K
5%
1/16W
5%
5%
1/16W
1/16W
R501
R503
R505
R511
R513
1-216-809-11
1-216-809-11
1-216-809-11
1-216-851-11
1-216-295-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
100
100
100
330K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R517
R518
R519
R520
1-216-833-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
100
100
5%
5%
5%
5%
R521
1-216-809-11 METAL CHIP
100
5%
1/16W
1/16W
1/16W
1/16W
(XG700)
1/16W
(XG700)
R522
R526
R527
R528
R529
1-216-829-11
1-216-829-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R530
R532
R533
R535
R536
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R537
R538
R540
R541
R542
1-216-809-11
1-216-809-11
1-216-827-11
1-216-833-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
3.3K
10K
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R543
R545
R546
R547
R548
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R549
R550
R551
R552
R553
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R554
R555
R556
R557
R558
1-216-809-11
1-216-809-11
1-216-809-11
1-246-041-00
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
470
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/10W
1/16W
HCD-XG80/XG700
MAIN
Ref. No.
Part No.
Description
Remark
R559
R561
R563
R565
R567
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R568
R569
R570
R572
R573
1-216-809-11
1-216-809-11
1-216-841-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
47K
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R574
R575
R576
R577
R578
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R579
R580
R581
R582
R583
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R584
R585
R586
R587
R588
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R589
R590
R591
R593
R594
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-831-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
6.8K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R595
R596
1-216-841-11 METAL CHIP
1-216-831-11 METAL CHIP
47K
6.8K
5%
5%
R596
1-216-837-11 METAL CHIP
22K
R596
1-216-841-11 METAL CHIP
47K
R597
1-216-827-11 METAL CHIP
3.3K
R597
1-216-839-11 METAL CHIP
33K
R597
1-216-841-11 METAL CHIP
47K
R600
R601
R602
1-216-809-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
100
1K
1K
1/16W
(EA)
5%
1/16W
(EXCEPT EA, SP)
5%
1/16W
5%
1/16W
5%
1/16W
R603
R604
1-216-841-11 METAL CHIP
1-216-820-11 METAL CHIP
47K
820
5%
5%
R604
1-216-821-11 METAL CHIP
1K
5%
R605
R606
1-216-854-11 METAL CHIP
1-216-841-11 METAL CHIP
560K
47K
5%
5%
1/16W
1/16W
(XG700)
1/16W
(XG80)
1/16W
1/16W
R607
R608
R609
R651
R652
1-216-821-11
1-216-845-11
1-216-813-11
1-216-821-11
1-216-821-11
1K
100K
220
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1/16W
1/16W
(AEP, UK)
5%
1/16W
(E2, MX, AR)
5%
1/16W
(EA, SP)
5%
1/16W
(SP)
5%
Ref. No.
Part No.
Description
Remark
R653
R654
1-216-841-11 METAL CHIP
1-216-820-11 METAL CHIP
47K
820
5%
5%
R654
1-216-821-11 METAL CHIP
1K
5%
R655
R656
1-216-854-11 METAL CHIP
1-216-841-11 METAL CHIP
560K
47K
5%
5%
1/16W
1/16W
(XG700)
1/16W
(XG80)
1/16W
1/16W
R657
R658
R659
R701
R702
1-216-821-11
1-216-845-11
1-216-813-11
1-216-821-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100K
220
1K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R703
R704
R705
R706
R707
1-216-821-11
1-216-845-11
1-216-821-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100K
1K
100K
1K
5%
1/16W
5%
1/16W
5%
1/16W
5%
1/16W
5%
1/16W
(AEP, UK, MX)
R708
1-216-821-11 METAL CHIP
1K
R709
1-216-821-11 METAL CHIP
1K
R710
1-216-821-11 METAL CHIP
1K
R717
1-216-845-11 METAL CHIP
100K
R718
1-216-845-11 METAL CHIP
100K
5%
1/16W
(AEP, UK, MX)
5%
1/16W
(AEP, UK, MX)
5%
1/16W
(AEP, UK, MX)
5%
1/16W
(AEP, UK, MX)
5%
1/16W
(AEP, UK, MX)
R721
R722
R724
R751
R752
1-211-990-11
1-216-804-11
1-216-833-11
1-216-821-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
75
39
10K
1K
100K
0.5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R753
R754
R755
R756
R801
1-216-821-11
1-216-845-11
1-216-821-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100K
1K
100K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R802
R803
R804
R805
R806
1-216-829-11
1-216-809-11
1-216-841-11
1-216-841-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
100
47K
47K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R807
R808
R809
R810
R811
1-216-833-11
1-216-821-11
1-216-845-11
1-216-813-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
100K
220
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R901
R902
R903
R904
R961
1-216-829-11
1-216-837-11
1-216-821-11
1-216-833-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
22K
1K
10K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R962
R963
1-216-837-11 METAL CHIP
1-216-825-11 METAL CHIP
22K
2.2K
5%
5%
1/16W
1/16W
< VARIABLE RESISTOR >
RV301
1-238-600-11 RES, ADJ, CARBON 10K
71
HCD-XG80/XG700
MAIN
Ref. No.
RV351
MIC
Part No.
PA
Description
Remark
1-238-600-11 RES, ADJ, CARBON 10K
< VIBRATOR >
X501
1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
X502
1-781-107-21 VIBRATOR, SERAMIC (16MHz)
**************************************************************
A-4475-552-A MIC BOARD, COMPLETE
********************
< CAPACITOR >
C801
C802
C803
C804
C805
1-162-306-11
1-162-215-31
1-126-960-11
1-126-959-11
1-162-294-31
CERAMIC
CERAMIC
ELECT
ELECT
CERAMIC
0.01uF
47PF
1uF
0.47uF
0.001uF
30%
5%
20%
20%
10%
16V
50V
50V
50V
50V
C806
C810
C813
C814
C815
1-162-215-31
1-162-286-21
1-137-372-11
1-162-215-31
1-162-215-31
CERAMIC
CERAMIC
MYLAR
CERAMIC
CERAMIC
47PF
220PF
0.022uF
47PF
47PF
5%
10%
5%
5%
5%
50V
50V
50V
50V
50V
C816
C817
C818
C819
C821
1-126-961-11
1-126-961-11
1-162-215-31
1-162-215-31
1-104-664-11
ELECT
ELECT
CERAMIC
CERAMIC
ELECT
2.2uF
2.2uF
47PF
47PF
47uF
20%
20%
5%
5%
20%
50V
50V
50V
50V
16V
C822
C836
C880
C881
C882
1-104-664-11
1-162-306-11
1-126-961-11
1-162-215-31
1-162-215-31
ELECT
CERAMIC
ELECT
CERAMIC
CERAMIC
47uF
0.01uF
2.2uF
47PF
47PF
20%
30%
20%
5%
5%
16V
16V
50V
50V
50V
C884
1-126-961-11 ELECT
2.2uF
20%
50V
< CONNECTOR >
CN811
CN812
FL801
Ref. No.
Part No.
Description
R807
R809
R850
R852
1-249-429-11
1-249-417-11
1-249-417-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
10K
1K
1K
100K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
Remark
R853
R854
R855
R856
R857
1-249-417-11
1-249-437-11
1-249-429-11
1-247-899-00
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
47K
10K
680K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R869
R870
R872
R873
R874
1-247-875-11
1-247-887-00
1-249-421-11
1-247-839-11
1-249-431-11
CARBON
CARBON
CARBON
CARBON
CARBON
68K
220K
2.2K
2.2K
15K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R880
R881
R882
R883
R884
1-247-855-11
1-247-871-11
1-249-437-11
1-249-437-11
1-247-823-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
47K
47K
47K
470
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R885
1-249-429-11 CARBON
10K
5%
1/4W
R886
1-247-893-11 CARBON
390K
5%
1/4W
R887
1-249-429-11 CARBON
10K
5%
1/4W
R888
1-249-417-11 CARBON
1K
5%
1/4W
R891
1-247-903-00 CARBON
1M
5%
1/4W
**************************************************************
A-4475-583-A PA BOARD, COMPLETE (E2, MX, AR)
A-4475-591-A PA BOARD, COMPLETE (AEP, UK)
A-4476-049-A PA BOARD, COMPLETE (EA, SP)
*******************
4-875-327-31 HEAT SINK
< CAPACITOR >
C401
C402
1-126-963-11 ELECT
1-164-159-21 CERAMIC
4.7uF
0.1uF
1-785-316-11 PIN, CONNECTOR (STRAIGHT) 4P
1-785-318-11 PIN, CONNECTOR (STRAIGHT) 6P
C403
1-164-159-21 CERAMIC
0.1uF
< NOISE FILTER >
C404
1-164-159-21 CERAMIC
0.1uF
C405
1-164-159-21 CERAMIC
0.1uF
C412
C413
C432
C433
1-162-306-11
1-162-306-11
1-126-933-11
1-126-961-11
C433
1-424-228-11 FILTER, NOISE
20%
50V
50V
(XG700)
50V
(XG700)
50V
(XG700)
50V
(XG700)
0.01uF
0.01uF
100uF
2.2uF
20%
20%
20%
20%
1-126-962-11 ELECT
3.3uF
20%
16V
16V
16V
50V
(XG700)
50V
(XG80)
C801
C802
C803
C804
C807
1-128-582-11
1-162-290-31
1-162-286-21
1-126-967-11
1-128-560-11
10uF
470PF
220PF
47uF
22uF
20%
10%
10%
20%
20%
100V
50V
50V
50V
100V
C808
C809
C810
1-130-777-00 MYLAR
1-130-777-00 MYLAR
1-128-562-11 ELECT
0.1uF
0.1uF
47uF
10%
10%
20%
C810
1-128-578-11 ELECT
1uF
20%
100V
100V
100V
(XG80)
100V
(XG700)
< IC >
IC850
IC852
IC853
8-759-700-08 IC NJM4558S
8-759-700-08 IC NJM4558S
8-759-700-08 IC NJM4558S
< JACK >
J801
J802
1-770-226-11 JACK (LARGE TYPE) (MIX MIC)
1-770-226-11 JACK (LARGE TYPE) (GUITAR)
< TRANSISTOR >
Q880
Q881
Q882
Q883
8-729-620-05
8-729-029-86
8-729-029-86
8-729-029-40
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
DTC124ESA
DTC124ESA
DTA124ESA
CERAMIC
CERAMIC
ELECT
ELECT
ELECT
CERAMIC
CERAMIC
ELECT
ELECT
< RESISTOR >
R806
72
1-247-903-00 CARBON
1M
5%
1/4W
HCD-XG80/XG700
PA
Ref. No.
Part No.
Description
Remark
C811
1-130-491-00 MYLAR
0.047uF
5%
50V
C812
C813
C814
C815
C830
1-130-491-00
1-162-306-11
1-162-294-31
1-126-959-11
1-107-714-11
0.047uF
0.01uF
0.001uF
0.47uF
10uF
5%
20%
10%
20%
20%
50V
16V
50V
50V
50V
C831
C832
C841
1-126-964-11 ELECT
1-126-967-11 ELECT
1-127-812-11 ELECT
10uF
47uF
3300uF
C841
1-135-516-11 ELECT
3300uF
C842
1-127-755-11 ELECT
3300uF
20%
50V
20%
50V
20%
63V
(E2, MX, AR)
20%
63V
(AEP, UK, EA, SP)
20%
100V
(AEP, UK, EA, SP)
MYLAR
CERAMIC
CERAMIC
ELECT
ELECT
C842
1-127-815-11 ELECT
3300uF
C844
C845
C847
C848
1-130-777-00
1-126-943-11
1-164-159-21
1-164-159-21
MYLAR
ELECT
CERAMIC
CERAMIC
0.1uF
2200uF
0.1uF
0.1uF
20%
100V
(E2, MX, AR)
10%
100V
20%
25V
50V
50V
C849
C850
C851
C852
C853
1-164-159-21
1-107-721-11
1-128-582-11
1-162-290-31
1-162-286-21
CERAMIC
ELECT
ELECT
CERAMIC
CERAMIC
0.1uF
4.7uF
10uF
470PF
220PF
20%
20%
10%
10%
C854
C857
C858
C859
C861
1-126-967-11
1-128-560-11
1-164-159-21
1-164-159-21
1-130-491-00
ELECT
ELECT
CERAMIC
CERAMIC
MYLAR
47uF
22uF
0.1uF
0.1uF
0.047uF
20%
20%
C862
C863
C891
1-130-491-00 MYLAR
1-126-961-11 ELECT
1-127-812-11 ELECT
0.047uF
2.2uF
3300uF
C891
1-135-516-11 ELECT
3300uF
C892
1-127-755-11 ELECT
3300uF
5%
50V
20%
50V
20%
63V
(E2, MX, AR)
20%
63V
(AEP, UK, EA, SP)
20%
100V
(AEP, UK, EA, SP)
C892
1-127-815-11 ELECT
3300uF
C894
C895
C902
C903
1-130-777-00
1-107-721-11
1-164-159-21
1-126-933-11
MYLAR
ELECT
CERAMIC
ELECT
0.1uF
4.7uF
0.1uF
100uF
C904
C905
C906
C909
C910
1-126-964-11
1-126-968-11
1-126-943-11
1-164-159-21
1-104-664-11
ELECT
ELECT
ELECT
CERAMIC
ELECT
10uF
100uF
2200uF
0.1uF
47uF
5%
20%
20%
20%
20%
1-778-981-21 CONNECTOR, BOARD TO BOARD 13P
1-778-981-21 CONNECTOR, BOARD TO BOARD 13P
1-785-316-11 PIN, CONNECTOR (STRAIGHT) 4P
< DIODE >
D401
D402
D405
8-719-991-33 DIODE 1SS133T-77
8-719-991-33 DIODE 1SS133T-77
8-719-991-33 DIODE 1SS133T-77
50V
100V
50V
50V
50V
20%
100V
(E2, MX, AR)
10%
100V
20%
100V
50V
20%
16V
< CONNECTOR >
CN803
CN804
CN904
50V
100V
100V
50V
50V
50V
50V
25V
50V
16V
Ref. No.
Part No.
Description
Remark
D406
D801
8-719-991-33 DIODE 1SS133T-77
8-719-991-33 DIODE 1SS133T-77
D802
D803
D804
D805
D831
8-719-110-49
8-719-991-33
8-719-991-33
8-719-991-33
8-719-060-53
DIODE
DIODE
DIODE
DIODE
DIODE
RD18ESB2
1SS133T-77
1SS133T-77
1SS133T-77
RBV-2506
D833
D834
D835
D836
D841
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
11ES2
11ES2
11ES2
11ES2
D842
D843
D844
D851
D852
8-719-200-82
8-719-200-82
8-719-200-82
8-719-991-33
8-719-110-49
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
11ES2
11ES2
1SS133T-77
RD18ESB2
D853
D902
D903
D904
D905
8-719-991-33
8-719-210-21
8-719-210-21
8-719-210-21
8-719-210-21
DIODE
DIODE
DIODE
DIODE
DIODE
1SS133T-77
11EQS04
11EQS04
11EQS04
11EQS04
D906
D911
D912
8-719-991-33 DIODE 1SS133T-77
8-719-982-37 DIODE MTZJ-39C
8-719-109-89 DIODE RD5.6ESB2
< IC >
IC801
IC801
IC901
8-749-017-06 IC STK412-150 (XG700)
8-749-017-07 IC STK412-170 (XG80)
8-759-450-47 IC BA05T
< COIL >
L401
L402
1-420-872-00 COIL, AIR-CORE (XG700)
1-420-872-00 COIL, AIR-CORE (XG700)
< TRANSISTOR >
Q401
Q402
Q431
Q432
Q433
8-729-029-40
8-729-140-84
8-729-140-84
8-729-119-76
8-729-620-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA124ESA-TP
2SC1841-PAFAEA
2SC1841-PAFAEA
2SA1175-HFE
2SC2603-EF
Q434
Q437
Q439
Q801
Q803
8-729-620-05
8-729-620-05
8-729-620-05
8-729-140-84
8-729-140-82
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2603-EF
2SC2603-EF
2SC2603-EF
2SC1841-PAFAEA
2SA988-PAFAEA
Q804
Q805
Q831
Q832
Q833
8-729-140-84
8-729-231-55
8-729-029-86
8-729-620-05
8-729-029-40
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1841-PAFAEA
2SC2878-AB
DTC124ESA
2SC2603-EF
DTA124ESA
Q834
Q851
Q855
Q901
Q903
8-729-140-84
8-729-140-84
8-729-231-55
8-729-620-05
8-729-141-83
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1841-PAFAEA
2SC1841-PAFAEA
2SC2878-AB
2SC2603-EF
2SB1094-LK
Q908
8-729-119-76 TRANSISTOR
2SA1175-HFE
73
HCD-XG80/XG700
PA
Ref. No.
Part No.
Description
Remark
< RESISTOR >
0 R401
1-215-867-00 METAL OXIDE
470
5%
0 R401
1-215-868-00 METAL OXIDE
680
5%
R406
R407
R410
1-249-437-11 CARBON
1-249-437-11 CARBON
1-249-389-11 CARBON
47K
47K
4.7
5%
5%
5%
R411
1-249-389-11 CARBON
4.7
5%
R412
1-249-389-11 CARBON
4.7
5%
R413
1-249-389-11 CARBON
4.7
5%
R414
1-260-076-11 CARBON
10
5%
R415
1-260-076-11 CARBON
10
5%
R429
R431
R432
R434
R437
1-249-437-11
1-249-438-11
1-249-437-11
1-249-433-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
56K
47K
22K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R439
R440
1-249-425-11 CARBON
1-249-433-11 CARBON
4.7K
22K
5%
5%
R440
1-249-437-11 CARBON
47K
5%
R441
R446
1-249-435-11 CARBON
1-249-429-11 CARBON
33K
10K
5%
5%
1/4W
1/4W
(XG80)
1/4W
(XG700)
1/4W
1/4W
R447
R801
R802
R803
R804
1-249-437-11
1-249-417-11
1-249-437-11
1-249-412-11
1-249-435-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
1K
47K
390
33K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
0 R805
0 R806
0 R807
0 R808
R809
1-216-436-00
1-216-436-00
1-212-881-11
1-214-789-00
1-260-076-11
METAL OXIDE
METAL OXIDE
FUSIBLE
METAL
CARBON
3.9K
3.9K
100
0.1
10
5%
5%
5%
10%
5%
1W
1W
1/4W
5W
1/2W
R810
R811
R812
R813
R814
1-249-437-11
1-249-417-11
1-249-431-11
1-249-441-11
1-249-421-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
1K
15K
100K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R815
R816
R817
R818
R819
1-249-433-11
1-249-429-11
1-249-421-11
1-249-409-11
1-249-439-11
CARBON
CARBON
CARBON
CARBON
CARBON
22K
10K
2.2K
220
68K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
0 R820
R821
R822
R823
R824
1-202-972-61
1-249-435-11
1-249-433-11
1-249-433-11
1-249-418-11
FUSIBLE
CARBON
CARBON
CARBON
CARBON
1
33K
22K
22K
1.2K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W
1/4W
1/4W
0 R825
R827
1-215-891-11 METAL OXIDE
1-249-441-11 CARBON
680
100K
5%
5%
2W
F
1/4W
74
1W
F
(XG80)
1W
F
(XG700)
1/4W
1/4W
1/4W
(XG700)
1/4W
(XG700)
1/4W
(XG700)
1/4W
(XG700)
1/2W
(XG700)
1/2W
(XG700)
F
F
F
F
Ref. No.
Part No.
Description
Remark
R828
R831
R832
1-247-903-00 CARBON
1-249-441-11 CARBON
1-249-441-11 CARBON
1M
100K
100K
5%
5%
5%
1/4W
1/4W
1/4W
R833
1-247-856-00 CARBON
11K
5%
R833
1-249-429-11 CARBON
10K
5%
R834
R835
R836
1-249-429-11 CARBON
1-249-437-11 CARBON
1-249-417-11 CARBON
10K
47K
1K
5%
5%
5%
1/4W
(XG80)
1/4W
(XG700)
1/4W
1/4W
1/4W
R837
R838
R839
R840
R851
1-249-435-11
1-249-435-11
1-249-441-11
1-249-402-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
33K
33K
100K
56
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R852
R853
0 R855
0 R857
0 R858
1-249-437-11
1-249-412-11
1-215-891-11
1-212-881-11
1-214-789-00
CARBON
CARBON
METAL OXIDE
FUSIBLE
METAL
47K
390
680
100
0.1
5%
5%
5%
5%
10%
1/4W
1/4W
2W
F
1/4W F
5W
F
R859
R860
R861
R862
R863
1-260-076-11
1-249-437-11
1-249-417-11
1-249-431-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
CARBON
10
47K
1K
15K
100K
5%
5%
5%
5%
5%
1/2W
1/4W
1/4W
1/4W
1/4W
R864
R865
R868
R880
0 R888
1-249-425-11
1-249-433-11
1-249-409-11
1-249-402-11
1-214-789-00
CARBON
CARBON
CARBON
CARBON
METAL
4.7K
22K
220
56
0.1
5%
5%
5%
5%
10%
1/4W
1/4W
1/4W
1/4W
5W
F
R889
0 R898
R901
R902
R903
1-249-441-11
1-214-789-00
1-249-429-11
1-249-441-11
1-249-429-11
CARBON
METAL
CARBON
CARBON
CARBON
100K
0.1
10K
100K
10K
5%
10%
5%
5%
5%
1/4W
5W
F
1/4W
1/4W
1/4W
R904
R905
R906
R907
R915
1-249-417-11
1-249-429-11
1-247-807-31
1-247-807-31
1-247-791-91
CARBON
CARBON
CARBON
CARBON
CARBON
1K
10K
100
100
22
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
2W
F
(XG80)
2W
F
(XG700)
0 R916
1-215-890-11 METAL OXIDE
470
5%
0 R916
1-216-454-11 METAL OXIDE
390
5%
< RELAY >
RY401
1-515-920-11 RELAY
< THERMISTOR >
TH831
1-807-796-11 THERMISTOR
< TERMINAL >
TM401 1-537-925-61 TERMINAL BOARD (FRONT SPEAKER)
**************************************************************
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
HCD-XG80/XG700
PANEL FL
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
A-4475-589-A PANEL FL BOARD, COMPLETE
************************
Remark
< RESISTOR >
4-225-511-01 HOLDER FL TUBE
4-949-935-81 CUSHION (FL)
*
Description
< CAPACITOR >
R601
R602
R603
R604
R605
1-249-429-11
1-249-437-11
1-247-807-31
1-249-437-11
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
10K
47K
100
47K
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
C601
C602
C603
C604
C605
1-104-664-11
1-162-306-11
1-162-306-11
1-162-294-31
1-164-159-21
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
47uF
0.01uF
0.01uF
0.001uF
0.1uF
20%
30%
30%
10%
16V
16V
16V
50V
50V
R606
R607
R608
R609
R610
1-247-807-31
1-247-807-31
1-249-429-11
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
10K
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
C607
C641
C642
C643
1-104-664-11
1-126-964-11
1-126-964-11
1-162-303-11
ELECT
ELECT
ELECT
CERAMIC
47uF
10uF
10uF
0.0033uF
20%
20%
20%
30%
16V
50V
50V
16V
R611
R612
R613
R614
R615
1-249-429-11
1-249-429-11
1-249-429-11
1-249-429-11
1-249-410-11
CARBON
CARBON
CARBON
CARBON
CARBON
10K
10K
10K
10K
270
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
C644
C645
C646
C647
C648
1-126-964-11
1-104-664-11
1-162-306-11
1-126-963-11
1-126-960-11
ELECT
ELECT
CERAMIC
ELECT
ELECT
10uF
47uF
0.01uF
4.7uF
1uF
20%
20%
30%
20%
20%
50V
16V
16V
50V
50V
R616
R617
R618
R619
R620
1-249-410-11
1-247-903-00
1-247-807-31
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
270
1M
100
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
C649
1-126-960-11 ELECT
1uF
20%
50V
R621
R622
R623
R624
R625
1-247-807-31
1-249-429-11
1-247-807-31
1-249-429-11
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
10K
100
10K
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R626
R627
R628
R629
R630
1-249-429-11
1-249-420-11
1-249-410-11
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
10K
1.8K
270
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R631
R632
R633
R634
R635
1-249-410-11
1-249-411-11
1-249-413-11
1-249-414-11
1-249-415-11
CARBON
CARBON
CARBON
CARBON
CARBON
270
330
470
560
680
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R636
R637
R641
R642
1-249-417-11
1-249-418-11
1-247-893-11
1-247-893-11
CARBON
CARBON
CARBON
CARBON
1K
1.2K
390K
390K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
R643
R644
R645
R646
1-249-441-11
1-249-440-11
1-249-437-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
100K
82K
47K
100K
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
R647
R648
R649
R650
R651
1-249-440-11
1-249-429-11
1-249-420-11
1-249-435-11
1-247-895-00
CARBON
CARBON
CARBON
CARBON
CARBON
82K
10K
1.8K
33K
470K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R652
R653
R654
R655
R656
1-249-437-11
1-249-417-11
1-249-437-11
1-249-417-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
47K
1K
47K
1K
47K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R658
R659
R660
1-249-441-11 CARBON
1-249-441-11 CARBON
1-249-441-11 CARBON
100K
100K
100K
5%
5%
5%
1/4W
1/4W
1/4W
< CONNECTOR >
CN601
CN602
1-784-774-11 CONNECTOR, FFC 13P
1-568-838-11 SOCKET, CONNECTOR 21P
< DIODE >
D601
D602
D603
8-719-058-04 LED SEL5223S-TP15 (I/1)
8-719-050-84 DIODE RB441Q-40T-77
8-719-991-33 DIODE 1SS133T-77
< FLUORESCENT INDICATOR TUBE >
FL601
1-517-940-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC601
IC602
8-759-829-28 IC TMP88CP76F-1B71
8-759-083-77 IC BA3830F
< COIL >
L601
L602
L603
1-410-509-11 INDUCTOR
1-410-509-11 INDUCTOR
1-410-509-11 INDUCTOR
10uH
10uH
10uH
< NOISE FILTER >
LF601
1-424-228-11 FILTER, NOISE
< TRANSISTOR >
Q601
Q602
Q603
Q604
Q605
8-729-029-86
8-729-140-04
8-729-140-04
8-729-620-05
8-729-047-58
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC124ESA
2SB1116A-L
2SB1116A-L
2SC2603-EF
DTC114TLTL2
Q606
Q607
8-729-047-58 TRANSISTOR
8-729-047-58 TRANSISTOR
DTC114TLTL2
DTC114TLTL2
75
HCD-XG80/XG700
PANEL FL
Ref. No.
R661
Part No.
PANEL VR
Description
1-249-410-11 CARBON
Remark
270
5%
1/4W
Ref. No.
IC702
Part No.
Description
Remark
8-759-827-68 IC NJL62H400A-1
(REMOTE CONTROL RECEIVER)
< SWITCH >
< COIL >
S601
S602
S603
S604
S605
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (DISPLAY)
SWITCH, KEYBOARD (SPECTRUM ANALYZER)
SWITCH, KEYBOARD (TIMER SELECT)
SWITCH, KEYBOARD (SLEEP)
SWITCH, KEYBOARD (c/CLOCK SET)
S606
S607
S608
S609
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (GAME)
SWITCH, KEYBOARD (FUNCTION)
SWITCH, KEYBOARD (I/1)
SWITCH, KEYBOARD
(POWER SAVE/DEMO (STANDBY))
< VIBRATOR >
X601
1-781-312-11 VIBRATOR, CERAMIC (12.5MHz)
**************************************************************
PANEL VR BOARD
***************
< CAPACITOR >
C701
C702
C703
C704
C705
1-162-294-31
1-162-294-31
1-162-294-31
1-104-664-11
1-162-306-11
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
0.001uF
0.001uF
0.001uF
47uF
0.01uF
10%
10%
10%
20%
30%
50V
50V
50V
16V
16V
C711
C712
C713
C714
C715
1-162-306-11
1-162-306-11
1-164-159-21
1-104-664-11
1-162-306-11
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
0.01uF
0.01uF
0.1uF
47uF
0.01uF
30%
30%
16V
16V
50V
16V
16V
20%
30%
L701
1-410-509-11 INDUCTOR
10uH
< RESISTOR >
R701
R702
R703
R704
R705
1-249-411-11
1-249-413-11
1-249-414-11
1-249-415-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
330
470
560
680
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R706
R707
R708
R709
R710
1-249-418-11
1-249-420-11
1-249-422-11
1-247-843-11
1-249-425-11
CARBON
CARBON
CARBON
CARBON
CARBON
1.2K
1.8K
2.7K
3.3K
4.7K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R711
R712
R713
R714
R715
1-249-427-11
1-249-429-11
1-249-431-11
1-249-434-11
1-249-411-11
CARBON
CARBON
CARBON
CARBON
CARBON
6.8K
10K
15K
27K
330
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R716
R717
R718
R719
R720
1-249-413-11
1-249-414-11
1-249-415-11
1-249-417-11
1-249-418-11
CARBON
CARBON
CARBON
CARBON
CARBON
470
560
680
1K
1.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R721
R722
R723
R724
R725
1-249-420-11
1-249-422-11
1-247-843-11
1-249-425-11
1-249-420-11
CARBON
CARBON
CARBON
CARBON
CARBON
1.8K
2.7K
3.3K
4.7K
1.8K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R726
R727
R728
R729
R730
1-249-422-11
1-247-843-11
1-249-425-11
1-249-427-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
2.7K
3.3K
4.7K
6.8K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
(XG700)
R734
R735
R736
R737
R738
1-249-417-11
1-249-417-11
1-249-401-11
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1K
47
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R739
R740
R771
R772
R773
1-247-807-31
1-249-429-11
1-249-403-11
1-249-403-11
1-249-403-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
10K
68
68
68
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R774
R775
R776
R777
R778
1-249-403-11
1-249-403-11
1-249-403-11
1-249-403-11
1-249-403-11
CARBON
CARBON
CARBON
CARBON
CARBON
68
68
68
68
68
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R779
R780
R783
R784
R785
1-249-403-11
1-249-403-11
1-249-403-11
1-249-407-11
1-249-407-11
CARBON
CARBON
CARBON
CARBON
CARBON
68
68
68
150
150
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
< CONNECTOR >
CN701
CN702
1-568-838-11 SOCKET, CONNECTOR 21P
1-770-010-21 CONNECTOR, BOARD TO BOARD 4P
< LED >
D701
D702
D703
D704
D705
8-719-058-03
8-719-058-03
8-719-058-03
8-719-058-03
8-719-058-03
LED
LED
LED
LED
LED
SEL5423E-TP15 (MOVIE)
SEL5423E-TP15 (ROCK)
SEL5423E-TP15 (REGGAE)
SEL5423E-TP15 (GUITAR)
SEL5423E-TP15 (SAMBA)
D706
D707
D708
D709
D710
8-719-058-03
8-719-058-03
8-719-058-03
8-719-058-03
8-719-058-03
LED
LED
LED
LED
LED
SEL5423E-TP15 (JAZZ)
SEL5423E-TP15 (TANGO)
SEL5423E-TP15 (DANCE)
SEL5423E-TP15 (GAME)
SEL5423E-TP15 (SALSA)
D713
D714
D715
D716
D717
8-719-058-03
8-719-058-04
8-719-058-04
8-719-058-04
8-719-058-04
LED
LED
LED
LED
LED
SEL5423E-TP15 (TUNER/BAND)
SEL5223S-TP15 (ENTER)
SEL5223S-TP15 (GUITAR DISTORTION)
SEL5223S-TP15 (ENTER/NEXT)
SEL5223S-TP15 (GROOVE)
D718
D719
8-719-058-04 LED SEL5223S-TP15 (SUPER WOOFER)
8-719-057-97 LED SEL5923A-TP15 (SURROUND)
< IC >
IC701
76
8-759-567-59 IC NJU3716L
HCD-XG80/XG700
PANEL VR
Ref. No.
Part No.
Description
Remark
SUB TRANS
Ref. No.
Part No.
TABLE SENSOR
Description
TC-A
Remark
< RELAY >
R786
R787
R788
R789
R790
1-249-407-11
1-249-407-11
1-249-407-11
1-249-403-11
1-249-409-11
CARBON
CARBON
CARBON
CARBON
CARBON
150
150
150
68
220
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R791
R792
1-249-409-11 CARBON
1-249-406-11 CARBON
220
120
5%
5%
1/4W
1/4W
0 RY901
1-755-276-11 RELAY, POWER
< SWITCH >
0 S901
1-786-055-21 SELECTOR, VOLTAGE (VOLTAGE SELECTOR )
(E2, EA, SP,AR)
< TRANSFORMER >
< SWITCH/ROTARY ENCODER >
S701
S702
S703
S704
S705
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (TUNER MEMORY)
SWITCH, KEYBOARD (ENTER/NEXT)
SWITCH, KEYBOARD (-)
SWITCH, KEYBOARD (TUNER/BAND)
SWITCH, KEYBOARD (+)
S706
S707
S708
S709
S710
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (STEREO/MONO)
SWITCH, KEYBOARD (TUNING MODE)
SWITCH, KEYBOARD (ENTER)
SWITCH, KEYBOARD (P.FILE)
SWITCH, KEYBOARD (FLAT)
S712
S713
S714
S715
S716
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (SURROUND)
SWITCH, KEYBOARD (GROOVE)
SWITCH, KEYBOARD (SUPER WOOFER)
SWITCH, KEYBOARD (SUPER WOOFER MODE)
SWITCH, KEYBOARD (GUITAR)
S717
S718
S719
S720
S721
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (JAZZ)
SWITCH, KEYBOARD (SAMBA)
SWITCH, KEYBOARD (DANCE)
SWITCH, KEYBOARD (TANGO)
SWITCH, KEYBOARD (SALSA)
S722
S723
S724
S725
S726
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (GAME)
SWITCH, KEYBOARD (b)
SWITCH, KEYBOARD (v)
SWITCH, KEYBOARD (V)
SWITCH, KEYBOARD (B)
S727
S728
S729
S730
S731
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (ROCK)
SWITCH, KEYBOARD (MOVIE)
SWITCH, KEYBOARD (REGGAE)
SWITCH, KEYBOARD (MIC GUITAR/KARAOKE)
SWITCH, KEYBOARD (GUITAR DISTORTION)
0 T901
1-435-827-11 TRANSFORMER, POWER (XG700)
0 T901
1-437-331-11 TRANSFORMER, POWER (XG80)
**************************************************************
1-659-058-13 TABLE SENSOR BOARD
*******************
*
< PHOTO INTERRUPTER >
IC202
8-749-924-18 PHOTO INTERRUPTER RPI-1391
< RESISTOR >
R207
1-249-416-11 CARBON
820
5%
1/4W
**************************************************************
1-680-171-11 TC-A BOARD
***********
< LED >
D621
D622
8-719-058-03 LED SEL5423E-TP15 (H)
8-719-058-03 LED SEL5423E-TP15 (h)
< RESISTOR >
R681
R682
R683
R684
R685
1-249-411-11
1-249-413-11
1-249-414-11
1-249-415-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
R686
R687
R688
1-249-418-11 CARBON
1-249-403-11 CARBON
1-249-403-11 CARBON
330
470
560
680
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
1.2K
68
68
5%
5%
5%
1/4W
1/4W
1/4W
< VARIABLE RESISTOR >
S732
1-762-875-21 SWITCH, KEYBOARD (PTY) (XG700)
S736
1-473-392-11 ENCODER, ROTARY (VOLUME)
**************************************************************
RV601
RV602
1-225-739-11 RES, VAR CARBON 50K (GUITAR LEVEL)
1-225-739-11 RES, VAR CARBON 50K (MIC LEVEL)
< SWITCH >
1-680-175-11 SUB TRANS BOARD
****************
< CAPACITOR >
0 C901
1-113-925-11 CERAMIC
0.01uF
20%
250V
S621
S622
S623
S624
S625
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (H)
SWITCH, KEYBOARD (h)
SWITCH, KEYBOARD (x)
SWITCH, KEYBOARD (. AMS > m)
SWITCH, KEYBOARD (. AMS > M)
< CONNECTOR >
CN901
* CN902
CN902
1-564-321-00 PIN, CONNECTOR 2P
1-564-321-21 PIN, CONNECTOR 2P (AEP, UK, MX)
1-568-106-11 PIN, CONNECTOR 4P (E2, EA, SP, AR)
S626
1-762-875-21 SWITCH, KEYBOARD (DOLBY NR)
S627
1-762-875-21 SWITCH, KEYBOARD (DIRECTION)
**************************************************************
< DIODE >
0 D901
8-719-991-33 DIODE 1SS133T-77
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
77
HCD-XG80/XG700
TC-B
Ref. No.
TRANS
Part No.
Description
Remark
1-680-172-11 TC-B BOARD
***********
Ref. No.
Part No.
0 F962
0 F963
0 F964
1-533-949-31 FUSE, CYLINDRICAL (TIME LUG) (T8AL/250V)
1-532-506-31 FUSE (T6.3AL/250V)
1-532-506-31 FUSE (T6.3AL/250V)
Description
Remark
< LED >
< RESISTOR >
D611
D612
D613
D614
8-719-058-03
8-719-058-03
8-719-057-97
8-719-058-04
LED
LED
LED
LED
SEL5423E-TP15 (h)
SEL5423E-TP15 (H)
SEL5923A-TP15 (X)
SEL5223S-TP15 (z REC)
0 R951
1-219-121-11 FUSIBLE
0.22
5%
1/4W F
0 R952
1-219-121-11 FUSIBLE
0.22
5%
1/4W F
0 R953
1-219-119-81 FUSIBLE
0.1
5%
1/4W F
**************************************************************
< RESISTOR >
R662
R663
R664
R665
R666
1-249-411-11
1-249-413-11
1-249-414-11
1-249-427-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
330
470
560
6.8K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R667
R668
R669
R670
R671
1-249-431-11
1-249-434-11
1-249-438-11
1-249-403-11
1-249-403-11
CARBON
CARBON
CARBON
CARBON
CARBON
15K
27K
56K
68
68
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R672
R673
1-249-403-11 CARBON
1-249-407-11 CARBON
68
150
5%
5%
1/4W
1/4W
< SWITCH >
S611
S612
S613
S614
S615
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (X)
SWITCH, KEYBOARD (z REC)
SWITCH, KEYBOARD (H SPEED DUB)
SWITCH, KEYBOARD (CD SYNC)
SWITCH, KEYBOARD (h)
S616
1-762-875-21 SWITCH, KEYBOARD (H)
S617
1-762-875-21 SWITCH, KEYBOARD (x)
S618
1-762-875-21 SWITCH, KEYBOARD (. AMS > m)
S619
1-762-875-21 SWITCH, KEYBOARD (. AMS > M)
**************************************************************
1-680-174-11 TRANS BOARD
*************
< CAPACITOR >
1-130-777-00
1-130-777-00
1-162-306-11
1-162-306-11
MYLAR
MYLAR
CERAMIC
CERAMIC
0.1uF
0.1uF
0.01uF
0.01uF
10%
10%
30%
30%
1-564-214-11 PIN, CONNECTOR (B3PS-VH) 3P
1-564-526-11 PLUG, CONNECTOR 11P
< DIODE >
D832
1-769-977-11
1-773-009-11
1-693-484-11
1-693-488-11
1-693-490-11
WIRE (FLAT TYPE) (13 CORE) (XG80)
WIRE (FLAT TYPE) (15 CORE) (XG700)
TUNER (FM/AM) (E2)
TUNER (FM/AM) (EA, AR, SP, MX)
TUNER (FM/AM) (AEP, UK)
6
72
73
109
112
1-535-706-21
1-773-056-11
1-773-032-11
1-751-688-11
1-773-150-11
PLUG, JUMPER (XG80: MX/XG700)
WIRE (FLAT TYPE) (17 CORE)
WIRE (FLAT TYPE) (15 CORE)
WIRE (FLAT TYPE) (13 CORE)
WIRE (FLAT TYPE) (21 CORE)
151
0 153
0 153
0 153
0 153
1-790-287-11
1-575-653-11
1-777-071-51
1-777-071-81
1-783-941-12
WIRE (FLAT TYPE) (19 CORE)
CORD, POWER (MX)
CORD, POWER (AEP, UK)
CORD, POWER (EA, SP)
CORD, POWER (AR)
0 153
465
507
0 601
602
1-791-901-11
1-454-887-21
1-452-925-21
8-820-020-02
1-782-817-11
CORD, POWER (E2)
SOLENOID, PLUNGER
MAGNET ASSY
OPTICAL PICK-UP KSS-213D/Q-RP
WIRE (FLAT TYPE) (16 CORE)
HP101 A-2004-778-A
HRPE101A-2004-779-A
M1
X-3378-246-1
M101
X-4917-523-3
M102
X-4917-504-1
100V
100V
16V
16V
< CONNECTOR >
* CN951
* CN952
4
4
5
5
5
BASE (A) ASSY, HEAD
BASE (B) ASSY, HEAD
MOTOR ASSY (CAPSTAN) (TAPE)
MOTOR ASSY (SPINDLE) (CD)
MOTOR ASSY (SLED) (CD)
M201
A-4660-977-A MOTOR ASSY (TABLE) (CD)
M901
1-763-072-11 FAN, D.C.
0 T951
1-435-246-11 TRANSFORMER, POWER (XG80)
0 T951
1-435-799-11 TRANSFORMER, POWER (XG700)
************************************************************
1-533-217-31 HOLDER, FUSE
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
C834
C893
C961
C963
MISCELLANEOUS
**************
8-719-510-68 DIODE D5SBA204101
**************
HARDWARE LIST
**************
#1
#2
#3
#4
#5
7-685-871-01
7-685-872-09
7-685-646-79
7-685-650-79
7-685-881-09
SCREW +BVTT 3X6 (S)
SCREW +BVTT 3X8 (S)
SCREW +BVTP 3X8 TYPE2 N-S
SCREW +BVTP 3X16 TYPE2 IT-3
SCREW +BVTT 4X8 (S)
#11
7-628-254-05 SCREW +PS 2.6X5
#12
7-685-781-09 SCREW +PTT 2X4 (S)
#13
7-623-921-01 RING, RETAINING, CAPSTAN
************************************************************
< FUSE >
0 F951
0 F961
78
1-533-949-31 FUSE, CYLINDRICAL (TIME LUG) (T8AL/250V)
(E2, EA, SP, AR)
1-533-949-31 FUSE, CYLINDRICAL (TIME LUG) (T8AL/250V)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
HCD-XG80/XG700
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
ACCESSORIES & PACKING MATERIALS
*******************************
0
0
1-569-008-21 ADAPTOR, CONVERSION (EA, SP)
1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
79
HCD-XG80/XG700
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
1.0
Date
2001.03
Description of Revision
New